Impact of Industrial Effluent on the Environment

IMPACT OF INDUSTRIAL EFFLUENT ON THE ENVIRONMENT

(REVISED EDITION)

BY:

ADEODUN SIMILADE ADEOLU B.Sc. WATER RESOURCES MANAGEMENT

M.Sc. ENVIRONMENTAL CONTROL AND MANAGEMENT

EXAMINED BY:

Prof. I. F. ADENIYI

ENVIRONMENTAL POLLUTION MONITORING TECHNIQUES

AND

Dr. (Mrs) A. A. OKOYA WATER TREATMENT AND WATERWORKS

INSTITUTE OF ECOLOGY AND ENVIRONMENTAL STUDIES

OBAFEMI AWOLOWO UNIVERSITY, ILE-IFE

NOVEMBER, 2016

Impact of Waste / Effluent on the Environment Adeodun Similade A.

Water and Environment Management Institute of Ecology and Environmental Studies,

Obafemi Awolowo University, Ile-Ife, Nigeria.

2

TABLE OF CONTENT

TABLE OF CONTENT ............................................................................................................. 2

WATER RESOURCES ............................................................................................................. 3

Sources and Distribution of Water Resources ....................................................................... 4

Hydrologic Cycle ................................................................................................................... 6

WATER POLLUTION .............................................................................................................. 8

Point Source Pollution ......................................................................................................... 10

Non-Point Source Pollution ................................................................................................. 10

INDUSTRIAL EFFLUENT..................................................................................................... 11

IMPACTS OF EFFLUENT ON THE ENVIRONMENT ....................................................... 12

Impact of Industrial Effluent on Water Bodies (Hydrosphere) ........................................... 13

Impact of Industrial Effluent on the Soil (Lithosphere) ....................................................... 14

Impact of Industrial Effluent on the Air (Atmosphere) ....................................................... 15

Impact of Industrial Effluent on Human .............................................................................. 15

REFERENCES ........................................................................................................................ 17




3

WATER RESOURCES

The earth is a water planet. From outer space, the oceans are visible as great swirls of blue

covering about 70 percent of the earth surface. The blue-white of ice snow covers another 3.5

percent. Below the patches and linear clouds are lakes and rivers, ponds and streams; unseen

beneath the surface are vast reservoirs of groundwater (Speidel, 1988). Speidel states further

that the earth is the only water world we know, the only planet where the compound water

(H2O) exists as liquid, vapour and solid. There appears to be only a very small set of conditions

in any solar system where the three states of water can so exist. Earth’s size and location relative

to those of the sun fit within that small set (Strahler, 2008). The change of water from one

physical state to another in the hydrologic cycle is a major factor influencing the geological,

chemical, physical and biological processes operating on the surface of the earth, including the

development and maintenance of life.

Sometimes it may feel like there is an infinite supply of fresh water. Yet, available fresh water

amounts to less than one-half of one Percent of all the water on earth.

Water is life. Water is very essential to life, for without it, no life can survive whether man,

animal or plant. It is a well-known fact that while man can do without solid food for more than

40 days; it is most unlikely that he can survive without water for 7 days. Water is a natural

resource of any country. With the fast growth in world population, the water resources of the

world are becoming one of the most important assets. In the present age, the importance of

water has further increased due to industrialization of the world as much potable water is

needed for the production of many industrial goods, generation of hydropower and irrigation

purposes etc. Water is also an important means of transportation in many parts of the world

and a significant factor in recreation. With the advancement in civilization, men has increased

the rate of pollution of the much needed resource, making it unfit for so many uses.




4

Sources and Distribution of Water Resources

The primary sources of water include: rainwater, surface water (stored in lakes, streams, and

ponds), and groundwater. The distribution of water, however, is quite varied; many locations

have plenty of it while others have very little. Water exists on earth in three forms solid (ice),

liquid or gas (water vapour) (Shiklomanov, 1998). Oceans, rivers, clouds, and rain, all of which

contain water, are in a frequent state of change (Huntington, 2006) (surface water evaporates,

cloud water precipitates, rainfall infiltrates the ground, etc.). However, the total amount of the

earth's water does not change; owing to glaciers, rivers and groundwater flow (Shiklomanov,

1998).

Figure 1 shows the global water occurrence and distribution. Of the small amount that is

actually freshwater, only a relatively small portion is available to sustain human, plant, and

animal life. The bar chart shows how almost all of Earth's water is saline and is found in the

oceans. In the first bar, only 2.5% of Earth's water is freshwater - the amount needed for life to

survive. The middle bar shows the breakdown of freshwater. Almost all of it is locked up in

ice and in the ground. Only a little more than 1.2% of all freshwater is surface water, which

serves most of life's needs. The right bar shows the breakdown of surface freshwater. Most of

this water is locked up in ice, and another 20.9% is found in lakes. Rivers make up 0.49% of

surface freshwater. Although rivers account for only a small amount of freshwater, this is where

humans get a large portion of their water from (Craig et al., 1996).




5

Figure 1: global water occurrence and distribution

Around fifty years ago, the common perception was that water was an infinite resource. At that

time, there was fewer than half the current number of people on the planet. People were not as

wealthy as today, consumed fewer calories and ate less meat, so less water was needed to

produce their food. They required a third of the volume of water we presently take from rivers

(Falkenmark and Rockström, 2004).

Today, the competition for water resources is much more intense. This is because there are now

seven billion people on the planet, their consumption of water-thirsty meat and vegetables is




6

rising, and there is increasing competition for water from industry, urbanization biofuel crops,

and water reliant food items (Postel and Wolf, 2001). In the future, even more water will be

needed to produce food because the Earth's population is forecast to rise to 9 billion by 2050

(Borkotoki et al., 2015; Cáceres, 2012; Lipae and Deligero, 2012).

Hydrologic Cycle

The movement of water on the earth's surface and through the atmosphere is known as the

hydrologic cycle (De Marsily, 1986). Water is taken up by the atmosphere from the earth's

surface in vapour form through evaporation. It may then be moved from place to place by the

wind until it is condensed back to its liquid phase to form clouds. Water then returns to the

surface of the earth in the form of either liquid (rain) or solid (snow, sleet, etc.) precipitation.

Water transport can also take place on or below the earth's surface by flow (Pidwirny, 2006;

Chahine, 1992; Thurow, 1991; Tuan, 1968).

The hydrologic cycle (Figure 2) is used to model the storage and movement of water between

the biosphere, atmosphere, lithosphere and hydrosphere (Wood et al., 2011). Water is stored

in the following reservoirs: atmosphere, oceans, lakes, rivers, glaciers, soils, snowfields, and

groundwater. It moves from one reservoir to another by processes like: evaporation,

condensation, precipitation, deposition, runoff, infiltration, sublimation, transpiration, and

groundwater flow (Pidwirny, 2006).




7

Figure 2: The Hydrologic Cycle: Delaware River Basin Commission (River, 2002)

Water is stored in the atmosphere in all three states of matter. Water vapour in the atmosphere

is commonly referred to as humidity. If liquid and solid forms of water can overcome

atmospheric updrafts they can fall to the Earth's surface as precipitation. The formation of ice

crystals and water droplets occurs when the atmosphere is cooled to a temperature that causes

condensation or deposition (Pidwirny, 2006). Four processes that can cause atmospheric

cooling are: orographic uplift; convectional uplift; air mass convergence; and radiative energy

loss.

Precipitation can be defined as any aqueous deposit, in liquid or solid form, that develops in a

saturated atmospheric environment and generally falls from clouds. A number of different

precipitation types have been classified by meteorologists including rain, freezing rain, snow,

ice pellets, snow pellets, and hail. Fog represents the saturation of air near the ground surface.




8

Classification of fog types is accomplished by the identification of the mechanism that caused

the air to become saturated (Fletcher et al., 2011).

The distribution of precipitation on the Earth's surface is generally controlled by the absence

or presence of mechanisms that lift air masses to cause saturation. It is also controlled by the

amount of water vapour held in the air, which is a function of air temperature (Fletcher et al.,

2011).

WATER POLLUTION

Water pollution is unarguably one of the most fundamental environmental issues globally and

locally, as untreated or inadequately treated wastes is being discharged into streams, estuaries

and seas (Novotny, 2003). Pollution of water bodies in Nigeria is further worsening with lack

of adequate environmental monitoring schemes; weak enforcement of environmental

regulations; and worst of all bribery and corruption (Nwabuzor, 2005; Winbourne, 2002).

Numerous studies have been and are being conducted to help define this problem; to determine

the amounts of pollutant substances released to the environment, their sources, their impacts,

and possible means of control (Kim et al., 2013).

Water is considered polluted if some substances or condition is present to such a degree that

the water cannot be used for a specific purpose. Water pollution occurs when unwanted

materials with potentials to threaten human and other natural systems find their ways into

rivers, lakes, wells, streams, boreholes or even reserved fresh water in homes and industries

(Rice et al., 2012). The pollutants are usually pathogens, silt and suspended solid particles such

as soils, sewage materials, disposed foods, cosmetics, automobile emissions, construction

debris and eroded banks from rivers and other waterways (Bakare and Akintan, 2016).




9

Water pollution affects plants and organisms living in bodies of water. In almost all cases the

effect is damaging not only to individual species and populations, but also to the natural

biological communities (Simberloff and Von Holle, 1999).

Pollution by organic and inorganic contaminant such as pesticide and heavy metals respectively

is a serious threat to aquatic ecosystems because some of these contaminants are potentially

toxic, even at very low concentrations. Additionally, heavy metals and pesticides are not

biodegradable and tend to accumulate in living organisms, and they can cause severe problems

to both human health and wildlife (Crini, 2005).

Water Pollutants can be grouped into three broad categories according to their nature:

I. Organic pollutants

II. Inorganic pollutants

III. Biological pollutants

Water pollutants can also be grouped according to source:

I. Point source

II. Non-point source

Water is in a continuous cycle (hydrological cycle), some pollutants from surface water

especially inorganic are capable of migrating from surface water to ground water (Carpenter et

al., 1998).

Surface waters may have the following types of pollutions:

Suspended Solids: The inorganic suspended solids blanket the stream bed effecting

benthos (flora and fauna at bottom of water) organisms, while the organic solids create

sludge banks and decompose causing odours and pathogens.

Floating Solids (Oils, Greases): Floating materials obstruct passage of light and aeration

which are vital for flora and fauna and self-purification of water.

Organic Matter: Biological decomposition of waste organic matter in stream depletes

dissolved oxygen content of water which may stifle the fish and aquatic life due to lack




10

of oxygen. Unpleasant odour, flavour and taste, result due to lack of dissolved oxygen.

Untreated sewage is the biggest pollutant and a cause of pathogens in water.

Inorganic Dissolved Salts: High total dissolved solids (TDS) may interfere with the use

of water in industries, municipal supplies and for irrigation purposes. Phosphorus and

Nitrogen are plant nutrients which induce algae growth and sometimes create

‘Eutrophic’ condition when excessive plant and algal growth may kill fishes and water

animals.

Toxic Chemicals and Heavy Metals: Acid, alkalis, toxic chemicals and heavy metals

cause adverse effect on human and animal life and plants.

Radioactive Materials: Radioactive materials cause adverse effects on all biological

beings.

Foam and Colour: Foam and colour are indicators of contaminations.

Microorganisms: Pathogenic bacteria, viruses, etc. are health hazards.

Thermal Pollution: Heat depletes dissolved oxygen in water adversely affecting fishes.

Higher temperature of water also adversely affects its use as coolant in industries.

Point Source Pollution

Point source pollution comes directly from a known source like an industrial or sewage outfall

pipe. It can also be from factories, wastewater treatment facilities, septic systems, and other

sources that are clearly discharging pollutants into water sources (Rehman et al., 2008). Point

sources are typically associated with manufacturing processes. However, point sources also

include discharges from water treatment plants and large animal feeding operations (Knight et

al., 2000).

Non-Point Source Pollution

Non-point source pollution can be defined as pollution that comes from many miscellaneous

or diffuse sources rather than from an identifiable, specific point (Harrington et al., 1985). Non-

point source pollution can originate from urban environments such as yards in neighbourhoods

or from agricultural production areas such as crop fields (Robbins et al., 2001).




11

Chemicals, waste products and soil that are carried by rain into streams or rivers become a part

of non-point source pollution (Alloway and Ayres, 1997). Common examples are fertilizers,

herbicides, pesticides, spilled motor oil and wastes from pets, wildlife and livestock. Other

significant sources of non-point source pollution include:

1. Litters

2. Hazardous waste improperly stored or discarded

3. Erosion from construction sites, farms or home sites

4. Pollution from roadways and road salting activities

5. Discharge of sewage and garbage from ships and boats

6. Cleansers and other compounds used on ships in the urban or agriculture environment

and boats to prevent barnacles and algae from accumulating

7. Disposal of wastes in catch basins

8. Improperly operating septic systems

9. Acid deposition including acid rain and fog

10. Leaking sewer lines

11. Improper use of fertilizers and pesticides

12. Animal feeding operations

Non-point sources are more difficult to identify, because they cannot be traced back to a

particular location (Sigel et al., 2010). Treatment of polluted water from non-point sources can

also be very difficult. Best management measure to non-point source pollution is the Watershed

Management system (Ritter and Shirmohammadi, 2000). Riparian community must act as

stakeholder in watershed management (Bulkley, 2011).

INDUSTRIAL EFFLUENT

Effluent is a wastewater, treated or untreated that flows out of a treatment plant, sewers, or

industrial outfall. It is liquid waste discharged from a sewage system, factory, nuclear power

station, or other industrial plant.

One of the most serious environmental problems is the existence of hazardous and toxic

pollutants in industrial wastewaters: problem because most of these wastewaters end up being




12

discharged to the environment. The major hindrance is the simultaneous existence of

many/different types of pollutants as

i. Dyes

ii. Heavy metals

iii. Phenols

iv. Pesticides and

v. Pharmaceuticals.

IMPACTS OF EFFLUENT ON THE ENVIRONMENT

Pollution of the aquatic environment has been defined by UNESCO /WHO/UNEP as the

introduction by man directly or indirectly of substances or energy into the marine environment

which results in such deleterious effects as harm to the living resources (Schwarzenbach et al.,

2010; Novotny, 2003; Harrington et al., 1985).

A major source of pollution in developing countries is industrial activities and this has

gradually increased the problem of waste disposal. Increased industrial activities have led to

pollution stress on surface water both from industrial, agricultural and domestic sources.

Untreated wastes from processing factories located in cities are discharged into inland water

bodies resulting to stench, discoloration and a greasy oily nature of such water bodies

(Akpomie et al., 2015; Olajumoke, 2010).

Industrial activities and urbanization in developing countries including Nigeria has gradually

led to increased problem of waste disposal. Increase in crude oil exploration, refining and

activities of other industrial establishments in the Niger Delta has resulted in the wide-scale

contamination of most of its creeks, swamps and rivers with hydrocarbon and dispersant

products (Olajumoke, 2010).

The major industrial categories in Nigeria are metals and mining, food, beverages and tobacco;

breweries, distilleries, textile, leather products, wood processing and manufacture, furniture,

pulp and paper industries and chemical and allied industries (Eluozo, 2013). Industrial effluents




13

contain toxic and hazardous materials from the wastes that settle in river water as bottom

sediments and constitute health hazards to the urban population that depend on the water as

source of supply for domestic uses (Akaninwor et al., 2007).

Meanwhile, the impact of industrial effluent has on the environment is not limited to water

bodies alone, rather cut across all portion of the environment. The various component of the

environment interact with each other, hence sooner or later, the harm done to the water bodies

would soon be felt by the land and the atmosphere (Sharma, 1994). According to Sharma 1994,

the impact of industrial effluent would be discussed as it affects each components of the

environment namely;

a) Impact on the water bodies (hydrosphere)

b) Impact on the soil (lithosphere)

c) Impact on the air i.e. atmosphere

d) Impact on human and on the ecosystem and flow of energy (food web)

Impact of Industrial Effluent on Water Bodies (Hydrosphere)

Contamination of drinking water supplies from industrial waste is as a result of various types

of industrial processes and disposal practices. Industries that use large amounts of water for

processing have the potential to pollute waterways through the discharge of their waste into

streams and rivers, or by run-off and seepage of stored wastes into nearby water sources

(Mathubala et al., 2015).

Other disposal practices which cause water contamination include deep well injection and

improper disposal of waste in surface impoundments. Industrial waste consists of both organic

and inorganic substances. Organic wastes include pesticide residues, solvents and cleaning

fluids, dissolved residue from fruits and vegetables, and lignin from pulp and paper (Ipinmoroti

et al., 2007). This impacts high organic pollutants on receiving waters consequently creating

high competition for oxygen within the ecosystem (Osibanjo and Adie, 2007). Effluents can




14

also contain inorganic wastes such as brine salts and metals. A number of toxic substances

human beings encounter regularly may pose serious health risks (Olajumoke, 2010). Pesticide

residues on vegetable crops, mercury in fish and many industrially produced chemicals may

cause cancer, birth defects genetic mutations or death. Discharge of metals and some non-

metals into water bodies have serious environmental effects (Förstner and Wittmann, 2012).

Lead a prime environmental pollutant, is a multi-organ poison which in addition to well-known

toxic effects depresses immune status, causes damage to the central nervous system, kidney

and reproductive system (Nwosu et al., 2014).

Thermal pollution is a major impact from industrial effluent as it alters the natural temperature

of the receiving water body (Abel, 1996). The native aquatic organisms of the receiving water

bodies would function normally under the condition they are used to. Deviation from the

normal condition could result in low in productivity, migration from the region or even mass

death of the fishes and other aquatic species (Langford, 1990).

Impact of Industrial Effluent on the Soil (Lithosphere)

Sometimes, effluent, especially sludge from the water or wastewater treatment facility are

disposed of by using them as soil amendment, or just indiscriminately to dump sites. When

these effluent or sludge (as the case may be) contains toxic materials and heavy metals, they

immediately become part of the soil; when these toxic materials and heavy metals become

ionised (i.e. in soluble form), they could be picked by the root of the plant and bioaccumulation

in the tissues of the plant (Mura et al., 2013). This is highly undesirable.

These toxic materials and heavy metals may also disrupt the natural activities of both the flora

and fauna components of the soil. The activities of bacterial and other micro-organisms could

be altered by the presence of these pollutants (Abel, 1996).




15

Impact of Industrial Effluent on the Air (Atmosphere)

Effluent especially when it contains high BOD and other organic pollutant tends to give off

foul smell. This worsens when the waste is not properly dosed with the required oxygen to

effectively digest the complex organic matter to simpler form. Disgusting gases like hydrogen

sulphide (H2S), cyanide (CN) among others is very notorious in this regards (Ghosh, 2002).

With uncontrolled release of effluent / wastewater, the undesirable foul smell could become a

threat to the inhabitants of such locality.

Impact of Industrial Effluent on Human

In non-ferrous metal industries, and industries that produce batteries, pigments, stabilizers and

plastics the primary heavy metals discharged are lead, zinc, and cadmium, also cement

manufacture results in high emission of mercury as well as these heavy metals except zinc

(Scoullos et al., 2012). Arsenic and Zinc gain access to the water environment through mining

operations. Nickel and Cobalt are used in the electroplating industry. Effluents contain these

heavy metals which are harmful to human health either through direct ingestion or from fish

and other animals or plants. Heavy metals particularly arsenic, mercury and lead are

environmental pollutants threatening the health of human population and natural ecosystem

(Castro-González and Méndez-Armenta, 2008).

The untreated effluent when released to the environment would interact with all components

of the environment. The effect would not only be felt in the water bodies alone, but across all

the components. The toxic component would definitely move round the food web / trophic

level (Förstner and Wittmann, 2012; Gavrilescu, 2004). According to Figure 3 below, the heavy

metals or other toxins could be picked up the root of the plants (the autotrophs), then be

transferred to primary consumer, and finally to the top of the food web, humans. The scary part




16

of this is that the toxins or heavy metals as it goes up the food web or trophic level tend to

increase up, that is referred to bio-magnification.

Figure 3: Bioaccumulation of Heavy Metals in the Food Chain




17

REFERENCES

Abel, P. D. (1996) Water pollution biology: CRC Press.

Akaninwor, J., Anosike, E., and Egwim, O. (2007) Effect of indomie industrial effluent

discharge on microbial properties of new calabar river. Sci Res Essays, 2(1), 1-5.

Akpomie, O., Buzugbe, H., and Eze, P. (2015) Effect of brewery effluent on the

microbiological quality of ikpoba river and surrounding borehole waters in benin city,

nigeria. British Microbiology Research Journal, 5(1), 76.

Alloway, B., and Ayres, D. C. (1997) Chemical principles of environmental pollution: CRC

Press.

Bakare, I. A., and Akintan, R. A. (2016) Economics of water governance-rural health survival

linkages in lagos: Evidence from badagry local government area. GLOBAL JOURNAL

OF APPLIED, MANAGEMENT AND SOCIAL SCIENCES, 11.

Borkotoki, B., Pegu, R., Baruah, P., Deka, P. C., Begum, A. M., Sarmah, A. K., Neog, B. K.,

Bora, P., Deka, S. N., and Rahman, N. (2015). IJTA.

Bulkley, J. W. (2011) Integrated watershed management: Past, present, and future. Journal of

Contemporary Water Research and Education, 100(1), 3.

Cáceres, S. B. (2012) Climate change and animal diseases: Making the case for adaptation.

Animal Health Research Reviews, 13(02), 209-222.

Carpenter, S. R., Caraco, N. F., Correll, D. L., Howarth, R. W., Sharpley, A. N., and Smith, V.

H. (1998) Nonpoint pollution of surface waters with phosphorus and nitrogen.

Ecological applications, 8(3), 559-568.

Castro-González, M., and Méndez-Armenta, M. (2008) Heavy metals: Implications associated

to fish consumption. Environmental toxicology and pharmacology, 26(3), 263-271.

Chahine, M. T. (1992) The hydrological cycle and its influence on climate. Nature, 359(6394),

373-380.

Craig, J. R., Vaughan, D. J., and Skinner, B. J. (1996) Resources of the earth: Origin, use, and

environmental impact: Prentice-Hall, Inc.

Crini, G. (2005) Recent developments in polysaccharide-based materials used as adsorbents in

wastewater treatment. Progress in polymer science, 30(1), 38-70.

De Marsily, G. (1986). Quantitative hydrogeology: Paris School of Mines, Fontainebleau.

Eluozo, S. N. (2013) Predictive model to monitor the migration of klebsiella influenced by void

ratio and porosity in homogeneous formation in choba, rivers state of nigeria.

Falkenmark, M., and Rockström, J. (2004) Balancing water for humans and nature: The new

approach in ecohydrology: Earthscan.

Fletcher, N. H., Squires, P., and Bowen, E. (2011) The physics of rainclouds: Cambridge

University Press.

Förstner, U., and Wittmann, G. T. (2012) Metal pollution in the aquatic environment: Springer

Science & Business Media.

Gavrilescu, M. (2004) Removal of heavy metals from the environment by biosorption.

Engineering in Life Sciences, 4(3), 219-232.

Ghosh, G. (2002) Water of india (quality & quantity): APH Publishing.




18

Harrington, W., Krupnick, A. J., and Peskin, H. M. (1985) Policies for nonpoint-source water

pollution control. Journal of Soil and Water Conservation, 40(1), 27-32.

Huntington, T. G. (2006) Evidence for intensification of the global water cycle: Review and

synthesis. Journal of Hydrology, 319(1), 83-95.

Ipinmoroti, K., Amoo, T., and Adebisi, Z. (2007) Effluent and receiving water quality near

food processing industries in ibadan metropolis. Journal of Food Technology, 5(1), 23-

28.

Kim, K.-H., Jahan, S. A., Kabir, E., and Brown, R. J. (2013) A review of airborne polycyclic

aromatic hydrocarbons (pahs) and their human health effects. Environment

international, 60, 71-80.

Knight, R. L., Payne, V. W., Borer, R. E., Clarke, R. A., and Pries, J. H. (2000) Constructed

wetlands for livestock wastewater management. Ecological engineering, 15(1), 41-55.

Langford, T. (1990) Ecological effects of thermal discharges: Springer Science & Business

Media.

Lipae, J. L., and Deligero, E. P. (2012) On forecasting water consumption in davao city using

autoregressive integrated moving average (arima) models and the multilayer perceptron

neural network (mlpnn) processes. International Journal of Humanities and Applied

Sciences, 1(4), 2277-4386.

Mathubala, G., Devi, R. K., and Ramar, P. (2015) Biosorption of thymol blue from industrial

wastewater using activated biocarbon from cynodon dactylon plant leaves.

Mura, S., Seddaiu, G., Bacchini, F., Roggero, P. P., and Greppi, G. F. (2013) Advances of

nanotechnology in agro-environmental studies. Italian Journal of Agronomy, 8(3), 18.

Novotny, V. (2003) Water quality: Diffuse pollution and watershed management: John Wiley

& Sons.

Nwabuzor, A. (2005) Corruption and development: New initiatives in economic openness and

strengthened rule of law. Journal of Business Ethics, 59(1-2), 121-138.

Nwosu, U., Ajiwe, V., and Okoye, P. (2014) Assessment of heavy metal pollution of effluents

from three (3) food industries in nnewi/ogidi areas of anambra state, nigeria. Mercury,

1, 0.497.

Olajumoke, A. (2010) Impact assesment of brewery effluent on water quality in majawe,

ibadan, southwestern nigeria.

Osibanjo, O., and Adie, G. (2007) Impact of effluent from bodija abattoir on the

physicochemical parameters of oshunkaye stream in ibadan city, nigeria. African

Journal of Biotechnology, 6(15).

Pidwirny, M. (2006) The hydrologic cycle. Fundamentals of Physical Geography, 2nd Edition.

Date Viewed. Pidwirny, M.

Postel, S. L., and Wolf, A. T. (2001) Dehydrating conflict. Foreign policy(126), 60.

Rehman, W., Zeb, A., Noor, N., and Nawaz, M. (2008) Heavy metal pollution assessment in

various industries of pakistan. Environmental Geology, 55(2), 353-358.

Rice, E., Bridgewater, L., Association, A. P. H., and Association, A. W. W. (2012) Standard

methods for the examination of water and wastewater.




19

Ritter, W. F., and Shirmohammadi, A. (2000) Agricultural nonpoint source pollution:

Watershed management and hydrology: CRC Press.

River, S. (2002) Delaware river basin commission.

Robbins, P., Polderman, A., and Birkenholtz, T. (2001) Lawns and toxins: An ecology of the

city. Cities, 18(6), 369-380.

Schwarzenbach, R. P., Egli, T., Hofstetter, T. B., Von Gunten, U., and Wehrli, B. (2010) Global

water pollution and human health. Annual Review of Environment and Resources, 35,

109-136.

Scoullos, M., Vonkeman, G. H., Thornton, I., and Makuch, Z. (2012) Mercury—cadmium—

lead handbook for sustainable heavy metals policy and regulation (Vol. 31): Springer

Science & Business Media.

Sharma, B. (1994) Water pollution: Krishna Prakashan Media.

Shiklomanov, I. A. (1998) World water resources. A new appraisal and assessment for the 21st

century.

Sigel, K., Klauer, B., and Pahl-Wostl, C. (2010) Conceptualising uncertainty in environmental

decision-making: The example of the eu water framework directive. Ecological

economics, 69(3), 502-510.

Simberloff, D., and Von Holle, B. (1999) Positive interactions of nonindigenous species:

Invasional meltdown? Biological invasions, 1(1), 21-32.

Speidel, R. E. (1988) Arbitration of statutory rights under the federal arbitration act: The case

for reform. Ohio St. J. on Disp. Resol., 4, 157.

Strahler, A. H. (2008) Modern physical geography: John Wiley & Sons.

Thurow, T. L. (1991) Hydrology and erosion. Grazing Management: An Ecological

Perspective. Timber Press, Portland, Oregon, 141-160.

Tuan, Y.-F. (1968) The hydrologic cycle and the wisdom of god: A theme in geoteleology:

University of Toronto Press.

Winbourne, S. (2002) Corruption and the environment. Management Systems International

and USAID, Washington.

Wood, E. F., Roundy, J. K., Troy, T. J., Van Beek, L., Bierkens, M. F., Blyth, E., de Roo, A.,

Döll, P., Ek, M., and Famiglietti, J. (2011) Hyperresolution global land surface

modeling: Meeting a grand challenge for monitoring earth's terrestrial water. Water

Resources Research, 47(5).

Impact of Industrial Effluent on the Environment

Documents

Transcript of Impact of Industrial Effluent on the Environment