SANDHYA ENTERPRISES

SANDHYA ENTERPRISES AN ISO 9001:2015 Certified Company

# 5‐24‐1223/5/1, Ambedkar Nagar Gajularamaram, Gajularamaram,Near of UMCC Hoptial ,

Qutuulapur Mandal R.R. Dist Hyderabad ‐500055 Telangana State India.

Contact No:9652998932, 95501921831,

Email: [email protected], [email protected],

Wessite:www.sandhyafex.com, www.sandhyaenterprises.co.in

BRAND NAME: “SANDHYAFEX”

Introduction: Dear Sir, We are manufacturer and Supplier of PVC and Rubber Products BRIDE CONSTRUCTION PRODUCTS 1. Elastomeric Bridge Bearing Pad 2.. Strip Seal Expansion Joint Seal. 3 Compression Seal Expansion Joint. 4.. Drainage Sport & Collection74 . 4.Slab Seal Expansion Joint 5. Rubber Speed Breaker IRRIGATION CONSTRUCTION PRODUCTS

1. PVC Water Stopper 2. NCT & NCL PVC Expansion Joint3. Mastic Pad 3. LDPE Sheet 4. Mastic pad

WATER AND DAM GATE PRODUCTS

1. Dam Gate Bulb Seal 2. Dam Gate Hollow Bulb Seal 3. Dam Gate Bottom Seal 4. Dam Gate Corner Seal

PIPE LINE RUBBER GASKET 1. DI & CI Pipe Gasket 2. REKA GRP & FRP Rubber Gasket.

3. NP3 Pipe (RCC) Gasket 4. SWR RUBBER RING RUBBER SUCTION HOSE

1. Rubber Water Suction Hose. 2. Fly Ash For Silo Rubber Hose 3. Cement Feeding Rubber Hose 4. Slurry Rubber Hose 5. Sand and Grovel Rubber Hose

INDUSTRIAL RUBBER HOSE 1. Sand and Shot Blast Rubber Hose 2. Carbon Free Hose 3. Chemical Hose 4. XLPE Chemical Hose 5. Hydraulic Hose R1 and R2 6. Rock Drill Hose 7. Air Hose IS :446 8. Water Hose IS:444 9. Water Delivery Rubber Hose

RUBBER BEADING

1. .Screen Vibrating Rubber Beading. 2. Squire Rubber Beading 3. Sponge Rubber Beading

RUBBER CORD

1. Natural Rubber Cord 2. EPMD Rubber Cord 3. SBR Rubber Cord 4. NBR Rubber Cord 5. Neoprene Rubber Cord

RUBBER EXPANSION JOINT BELLOW as per ASA 150#, PN 10 and PN 16 MS and SS Flange

1. EPMD Rubber Bellow 2. SBR Rubber Bellow 3. NBR Rubber Bellow 4. Neoprene Rubber Bellow

Industrial Rubber Sheet 1. Silicon Rubber Sheet

2. Insertion Rubber Sheet 3. Sponge Rubber Sheet

1.Elastomeric Bridge Bearing

Sandhya Enterprises AN ISO:9001;2015 Certified Company is manufacture and Supplier of

Elatomeric Bridge Bearing as per IRC 83 (Part II) 2015, MORTH and UIC 772 2R Specification:

Thickness:22mm to 144mm max

Width:100mm to 1000mm Max

Length:100mm to 1500mm Max

Hardness:55 to 65 IRHD

Tensile Strength:17.0MPa min

Elongation at Break:400% min

Adhesion Strenght:7kn/M

Ash Contact:5% max

Polymers : CR

Polymer Percentage:60%

Shear Modulus 0.8MPa to 1.2MPa

Shape Factor for Elastic Modulus:6 to 12

TEST REPORT

S. No

Tests IRC 83

(Part II)/1987 Clause Number

Permissible Limits as per

IRC 83(Part II) / 1987

Relevent Code for Testing

Procedure/Method Results

1 Physical Properties - Before Ageing

Hardness Test Table 1 Cl. 915.2 55 to 65 IRHD IS : 3400 (Part II) 60 to 62 IRHD

Tensile Strength Table 1 Cl. 915.2 17 MPa (Min) IS : 3400 (Part I) 19.85 MPa

Elongation at

Break Table 1 Cl. 915.2 400% (Min) IS : 3400 (Part I) 460-480%

2 Adhesion Strength Cl. 915.2.2 7 KN / m (Min) IS : 3400 (Part XIV) 12.50 KN / m

3 Ash Content Cl. 915.1.3 5 % (Max) IS : 3400 (Part

XXII) 3.50%

4 Polymer Percentage

Cl. 915.1.3 60 % (Min) IS : 3400 (Part

XXII) 61.60%

5 Polymer Cl. 915.1 Chloroprene(CR) ASTM D297 Chloroprene(CR)

6 Compression Set @100oC for 22 to 24 hours

Table 1 Cl. 915.2 35 % (Max) IS : 3400 (Part X) 17.86%

7 Physical Properties - After Ageing @ 100oC for 70 +2 Hours

Change in

Hardness Table 1 Cl. 915.2 + 15 Deg (Max) IS : 3400 (Part IV) + 7 Deg

Change in Tensile Strength %

Table 1 Cl. 915.2 - 15 % (Max) IS : 3400 (Part IV) - 8.35%

Change in

Elongation at Break in %

Table 1 Cl. 915.2 - 30 % (Max) IS : 3400 (Part IV) - 16.46%

S. No

Tests IRC 83 (Part II)/1987 Clause Number

Permissible Limitsas per IRC 83(Part II) /

2015



1 Hardness Table 1 Cl. 915.2 60+5 IRHD IS : 3400 (Part II) 60 - 61 IRHD

2 Elastic Modulus, EA ( MPa ) Cl. 10.5 328.05 MPa to 492.07 MPa

IRC : 83 (Part II)/1987 425.35 MPa

3 Shear Modulus, G ( MPa ) Cl. 9.2 0.80 to 1.20 MPa IRC : 83 (Part II)/1987 0.89 MPa

4 Length of the Bearing Table 2 Cl. 917.7 500 mm + 6 mm IRC : 83 (Part II)/1987

502 mm to 503 mm

5 Width of the Bearing Table 2 Cl. 917.7 360 mm + 6 mm IRC : 83 (Part II)/1987 362 mm to 363 mm

6 Thickness of the Bearing Table 2 Cl. 917.7 96 mm + 5 % (Max) IRC : 83 (Part II)/1987 96.3 mm to 97.5 mm

7 Ultimate compressive strength

Cl. 12 60 MPa (Min) IRC : 83 (Part II)/1987

Tested upto 82 MPa & found Satisfactory

8 Stripping Strength Cl. 11.3.3 3 MPa (Max) IRC : 83

(Part II)/1987 Tested & Found Ok

2.Strip Seal Expansion Joint

Sandhya Enterprises AN ISO: 9001;2015 Certified Company is manufacture and Supplier of

Strip Seal Expansion Joint as per IRC 83 (Part II) 2015, MORTH and UIC 772 2R Specification:

Gap 40mm and 70 and 80mm movement, 65mm and 75mm Edges Beam with 16mm

Anchoring Rod. Neoprene Rubber Strip as per IRC 83 (Part II)2015 Specification)

1. Edge beam shall be placed in such a manner that the grooves are positioned properly.

2. Steel structure and main reinforcement shall be anchored with proper welding.

3. Alignment shall be checked for both steel structures, if required by using suitable device.

4. Recess shall be filled with high quality of the concrete not less than M 35 grade.

5. If any installation brackets were used, shall be removed after the concrete has cured.

6. SANDHYAFLEX elastomeric strip seal shall be cut into the required length and inserted between the

beams by using the proper device and to be ensured that the bulb of the seal is getting into the steel

grooves of the both edge beams.

7. When the recess concrete has become set, a sturdy ramp shall be placed over the joint to protect the

exposed steel beams and the elastomeric seal from the traffic.

8. Without carriageway surfacing, expansion joint shall not be exposed to traffic loading.

S. No

Tests

MoRTH

Specification Section

2600, Clause 2607

Clause Number


MoRTH Specification Section 2600, Clause 2607


Procedure/Method

Results


Hardness Test Table 2600-

1 58-68 Shore A IS : 3400 (Part II) 60-62 Shore A

Tensile Strength Table 2600-

1 11 MPa (Min) IS : 3400 (Part I) 17.5 MPa

Elongation at

Break Table 2600-

1 350% (Min) IS : 3400 (Part I) 415%

2 Ash Content Cl. 915.1.3, IRC 83 (Part

II)2015 5 % (Max)

IS : 3400 (Part XXII)

3.50%

3 Polymer Percentage Cl. 915.1.3, IRC 83 (Part

II)2015 60 % (Min)


63.14%

4 Polymer Table 2600-

1 Chloroprene(CR

) ASTM D297

Chloroprene(CR)

5 Compression Set Table 1 Cl.

915.2 -28 % (Max) IS : 3400 (Part X) 16.22%

6 Shock Elasticity Table 2600-

1 -25 % (min) IS : 3400 (Part X) 27.25%

7 Tear Propogation Strength

Longitudinal Table 2600-

1 10N/mm (min IS : 3400 (Part 17) 45.22N/mm

Tranvers Table 2600-

1 10N/mm (min) IS : 3400 (Part 17) 50.24N/mm

8 Sweling behaviour in ASTM Oil No 3 for 70oC for 116 hrs

Valume Change Table 2600-

1 -25 % (max) IS : 3400 (Part 17) -16.22%

Change in

Hardness Table 2600-

1 -20 Shore A

(max) IS : 3400 (Part 17) -6 ShoreA

9 Physical Properties - After Ageing @ 70oC for 14days

Change in Tensile

Strength % Table 1 Cl.

915.2 - 20 % (Max) IS : 3400 (Part IV) -7.13%

Change in


Table 1 Cl. 915.2

- 20 % (Max) IS : 3400 (Part IV) -14.66%

Change in

Hardness Table 1 Cl.

915.2 + 5 Deg (Max) IS : 3400 (Part IV) +26

3.Compression Seal Expansion Joint

Sandhya Enterprises AN ISO: 9001;2015 Certified Company is manufacture and Supplier of

Compression Seal Expansion Joint as per IRC 83 (Part II) 2015, MORTH and UIC 772 2R

Specification:

Gap 40mm and 70 and 80mm movement, 100mm Edges Beam with 16mm Anchoring Rod.

Neoprene Rubber Strip as per IRC 83 (Part II)2015 Specification)

4.SLAB SEAL EXPANSION JOINT

S. No

Tests

MoRTH


2600, Clause 2607

Clause Number




Procedure/Method

Results






Elongation at Break Table 2600-

1 350% (Min) IS : 3400 (Part I) 415%


II)2015 5 % (Max)


3.50%


II)2015 60 % (Min)


63.14%


1 Chloroprene(CR

) ASTM D297

Chloroprene(CR)


915.2 -28 % (Max) IS : 3400 (Part X) 16.22%


1 -25 % (min) IS : 3400 (Part X) 27.25%








1 -25 % (max) IS : 3400 (Part 17) -16.22%

Change in Hardness Table 2600-

1 -20 Shore A



Change in Tensile


915.2 - 20 % (Max) IS : 3400 (Part IV) -7.13%

Change in


Table 1 Cl. 915.2

- 20 % (Max) IS : 3400 (Part IV) -14.66%

Change in Hardness Table 1 Cl.

915.2 + 5 Deg (Max) IS : 3400 (Part IV) +26

Sandhya Enterprises AN ISO:9001;2015 Certified Company is manufacture and Supplier of Slab Seal

Expansion Joint as per IRC 83 (Part II) 2015, MORTH and UIC 772 2R Specification:

Size:320mm Width x50mm Thickness x 1000mm (LG)

S. No

Tests

MoRTH


2600, Clause 2607

Clause Number




Procedure/Method

Results







1 350% (Min) IS : 3400 (Part I) 415%


II)2015 5 % (Max)


3.50%


II)2015 60 % (Min)


63.14%


1 Chloroprene(CR

) ASTM D297

Chloroprene(CR)


915.2 -28 % (Max) IS : 3400 (Part X) 16.22%


1 -25 % (min) IS : 3400 (Part X) 27.25%








1 -25 % (max) IS : 3400 (Part 17) -16.22%


1 -20 Shore A



Change in Tensile


915.2 - 20 % (Max) IS : 3400 (Part IV) -7.13%

Change in


Table 1 Cl. 915.2

- 20 % (Max) IS : 3400 (Part IV) -14.66%


915.2 + 5 Deg (Max) IS : 3400 (Part IV) +26

5.Omega Seal Expansion Joint

Sandhya Enterprises AN ISO:9001;2015 Certified Company is manufacture and Supplier of Slab Seal

Expansion Joint as per IRC 83 (Part II) 2015, MORTH and UIC 772 2R Specification:

1. Surface shall be 1% slope in order to get water drained as shown in figure.

2. Steel bolt shall be inserted into the recess made in the deck and to be filled with M 35 grade concrete.

3. SANDHYAFLEX cap seal to be positioned on both sides of the decks such a manner that the omega

shape covers the gap and the plain surface are perfectly sat on the deck slab.

4. Galvanized steel plate(80 X 80mm) having oblong hole (40 X 20mm) to be placed on the plain surface of

the seals at both sides , such a manner the bolt is inserted through the oblong holes.Seal also to be

punched with a hole suiting to oblong hole of the steel plate to enable to get inserted through the bolt.

5. Nut to be tightened on every bolt properly and tack welded to ensure the locking.

6. On completion of installation, every aspects to be checked for proper installation.

7. wearing coat shall be done with proper care without disturbing the seal.

S. No

Tests

MoRTH


2600, Clause 2607

Clause Number




Procedure/Method

Results







1 350% (Min) IS : 3400 (Part I) 415%


II)2015 5 % (Max)


3.50%


II)2015 60 % (Min)


63.14%


1 Chloroprene(CR

) ASTM D297

Chloroprene(CR)


915.2 -28 % (Max) IS : 3400 (Part X) 16.22%


1 -25 % (min) IS : 3400 (Part X) 27.25%








1 -25 % (max) IS : 3400 (Part 17) -16.22%


1 -20 Shore A



Change in Tensile


915.2 - 20 % (Max) IS : 3400 (Part IV) -7.13%

Change in


Table 1 Cl. 915.2

- 20 % (Max) IS : 3400 (Part IV) -14.66%


915.2 + 5 Deg (Max) IS : 3400 (Part IV) +26

6.DRAINAGE SPOUT.

A drainage spout is a vertical pipe for carrying rainwater down from a platform. It is made from mild steel and galvanized to prevent corrosion or rusting due to water flowing through the pipe. Drainage spouts are manufactured and supplied according to MORTH specifications. Our range of Deranges Spout and as per customers Drg.

RCC Construciton Products

1.PVC WATER STOPPER

1.PVC WATER STOPPER

A.PVC Water Stopper with Centre Bulb

1. SANDHYAFLEX –PVCWSCB‐150‐6” (150mm) x 5mm

2.SANDHYAFLEX –PVCWSTCB150‐6” (150mm) x 6mm

3.SANDHYAFLEX‐PVCWSCB150‐6” (150mm) x 8mm




7‐SANDHYAFLEX‐PVCWSCB230‐9” (230mm) x 10mm




B. PVC Water Stopper Dumbell

S.No Size

1 SANDHYAFLEX‐DBTPVCWAT150‐6” (150mm) x 6mm

2 SANDYAFLEX‐DBTPVCWS230‐9” (230mm) x 6mm

3 SANDHYAFLEX‐DBTPVCWS‐250‐10” (250mm) x 8mm

4 SANDHYAFLEX‐12” (305mm) x 8mm

C.PVC Water Stopper Kiker Type

S.No Size

1 SANDHYAFLEX‐KTPVCWS230‐9” (230mm) x 8mm

2 SANDHYAFLEX‐KTPVCWS300‐12” (305mm) x 8mm


PVC Water Stopper as per IS:15058‐2002 Specification:

Color: Black and White

Type:1. PVC Water Stopper with Centre Bulb

2.PVC Water Stopper Kicker Type

3. PVC Water Stopper Dumbell Type SANDHYAFLEX Water Stops are profiles based on specially formulated plasticized PVC composition. PVC Water Stopper is used in concrete masonry construction of hydraulic structures to safeguard from hydrostatic pressure and water seepage. Water Stopper also withstands expansion and contraction of joints as well takes care of any deflection and displacement arising due to change in temperature or settlement of foundation eliminating dangers of cracks since these is engineered as water tight seals in poured concrete structures. After being embedded in concrete, PVC water stops fill up the joints to form a continuous watertight diaphragm that prevents the passage of fluid. Most popular way of the placement of the water stop seal is tied to the steel frame works or small eyelet by means of small wires, certain metal clamps made to grip the water stop seal to keep it in proper position. The water stop must be designed and installed properly to accommodate joint expansions, contraction and lateral & transverse movements. In addition to these considerations, the water stop must be compatible with the concrete system and the liquids and chemicals to be contained or controlled. The basic kind of water stops, suggested normally for use in construction joints where movement is not expected, is the basic type of flat ribbed water stop, however the ribbed type with centre bulb is used in expansion joints where movement is likely to occur. SANDHYAFLEX PVC Water Stops have good ageing properties leading to longer life, have high mechanical strength, chemical resistance, corrosion resistance, excellent weather resistance, lower water absorption, non-hazardous and flame retardant, good shock bearing capacities against earth quakes, floods, heavy turbine vibrations, allows safe passage of seepage water, easy to weld and install.SANDHYAFELX PVC Water Stops maintains its premier position of the preferred industry supplier by offering customized products meeting specific needs of our customer. We offer a wide variety of PVC water stop in rolls, in width150mm up to 300 mm and thickness of 4 to 12 mm. We also welcome any special or customized design from the end user.

TEST REPORT

S. No

Tests IS:15058-2002 Specification

Clause Number


IS:15058-2002 Specification


Procedure/MethodResults


Hardness Test Cl.3.2 65 Shore A (min) IS : 3400 (Part II) 68 Shore A

Tensile Strength Cl.3.2 13.8 MPa (Min) IS : 3400 (Part I) 14.8MPa

Elongation at Break Cl.3.2 285% (Min) IS : 3400 (Part I) 320%

2 Water Absortion Cl.3.2 0.6% (max) IS : 3400 (Part VI) 0.35%

3 Cold Bend Test at -25oC Cl.3.2 Should be no any

crack IS : 9766 Fond OK

4 Accelarted Extraction Test

Tensile Strength Cl.3.2 10.3 MPa (Min) IS : 3400 (Part IV) 12.8MPa

Elongation at Break Cl.3.2 280% (Min) IS : 3400 (Part IV) 305%

5 Stability in effect of alkalies test

a. Weight increase at

7days Cl.3.2 0.25 % (Max) IS : 3400 (Part IV) 0.17%

b. Weight decrease at 7days

Cl.3.2 0.10 % (Max) IS : 3400 (Part IV) 0.05%

c. Change in Hardness at 7 days Cl.3.2 + 5 Shore (Max) IS : 3400 (Part

IV) -3/+ 2 Shore

A

d. Weight increase at 28days Cl.3.2 0.40 % (Max) IS : 3400 (Part

IV) 0.27%

e. Weight decrease at 28days

Cl.3.2 0.30 % (Max) IS : 3400 (Part IV) 0.15%

f. Dimension Change

Change in Elongation at Break in %

Cl.3.2 + 1% (Max) IS : 3400 (Part IV) -0.3/+ 0.25%

2.BITUMINIZED EXPANSION JOINT FILLER BOARDS Construction of concrete roads, runways, floor and roof slabs of buildings, involves casting of concrete in slab orm, which leads to construction joints. Provision must be made to accommodate the expansion and contraction at these joints which occurs with seasonal variations in temperature. Our Bitumen Impregnated Expansion Joint Fillers Boards display excellent resistance to compression, with outstanding recovery characteristics. Provision of these boards in the joints permits free movement of the concrete slabs. This prevents damage to the slabs besides providing waterproofing and resisting entry of foreign matter into the joints.

It is a low density high quality fibre board which is cellular in nature, securely bonded together and uniformly saturated with Bituminous Compound. Impregnation with Bituminous Compound makes it durable and water proof. Cellular nature provides compressible properties and ability to recover after compression load is released; conforming to Indian as well as international technical specifications. It bears normal structural movements without breaking or cracking. It ensures sealing of joints as no gap exists between the joint spaces. The fillers are environment friendly as opposed to the environment destroying thermocol /plastic expansion joint filler. FEATURES

Meets worldwide technical specifications 1. IS: 1838 2. ASTM: D.1751 3. BS: 1142 Excellent resiliency Unaffected by temperature extremes Excellent dimensional tolerances Non extruding Compression to 50% thickness in the initial state:- Recovery is 80/84% Weathering and compression to 50% thickness: – Recovery is 70/76%. Extrusion: No effect

(0.75 mm) Low moisture absorption due to bitumen impregnation. Standard Bitumen content 10-20-

35%. Other possibilities upon bulk orders Cuts cleanly

USES Preserves life and evenness of the slab Prevents seepage of surface water through the joints and ingress of water or dirt down

the joint

Relieves stress developed due to temperature, shrin kage, creep, relaxation, variation, vibration etc.

Relieves compressive stresses which develop when concrete expands in horizontal, vertical or inclined directions

Prevents the intrusion of foreign material into the joint which would prevent the joint from working

Useful in all types of concrete construction in both interior and exterior APPLICATION

Concrete expansion: sidewalk, retaining walls, patios, curbs and gutters, airport runways. Concrete isolation joints: bridge approaches, highway interchanges, dams, concrete

abutments Header plate sealer. Sill sealer.

USAGE

DIMENSIONS

Standard Thickness: 10MM, 12MM, 18MM, 25MM, 50MM Standard Sizes: 4’ x 2’, 4’ x 4’, 4’ x 8’ Size and thickness can be customized upon bulk orders

LDPE SHEET

Sandhya Enterprises Dealing and Supply LDPE Sheet as per IS:2508-1984 Specification

Density Polyethylene sheet has many names. It goes by the names poly sheeting, plastic sheeting, plastic

film, polyethylene sheet, and poly film to name a few. Polyethylene sheeting is a plastic film made from

petroleum. That is why the price of the product can vary depending on what oil prices are doing. It is sold

in rolls where in additives can be added to change the functionality of the film. Additive such as U.V.

inhibitors, fire retardants, anti-static additives are added so each variation can best serve it’s intended use.

LDPE Plastic Sheet, LDPE Sheets Mono Industries were established in the year 2016 at Hyderaad, India. We are an ISO 9001:2015 Certified Company and a reckoned name in the field of supplying a vast collection of LDPE Sheet. We are specialized in offering an expansive range of LDPE Plastic Sheet to high standards. Our specialization is in Supply HDPE Sheet of 30 micron to 1000 microns and width of 1 meter to 6 meter. Our production procedures conform to IS-2508/1984. Few application areas of our products are:

Agriculture (Mulching Film, Pond Lining Film) Automotive Industry (VCI Films) Construction Films (Protection Films, Lieving Films, Seepage Constructions)

Electronic Industry (Anti Static Films) Industries (Shrink Films, Cling Films, Stretch Films)

TEST REPORT

S. No

Tests IS:10655-1999-

Type I Clause Number

Permissible Limits as per IS:2508-1984

Specification



1 Physical Properties -Lengthwise direction

Tensile Strength Table-2.Cl. 4.3.1 120kgf/cm2 Min) IS : 3400 (Part I) 130kgf/cm2

Elongation at Break 12.5µm to bu not

including 75µm Table-2.Cl. 4.3.1 100% (Min) IS : 3400 (Part I) 125%

Elongation at Break above 75µm Table-2.Cl. 4.3.1 200% (Min) IS : 3400 (Part I) 220%

2 Physical Properties -Crosswise direction

Tensile Strength Table-2.Cl. 4.3.1 25kgf/cm2 Min) IS : 3400 (Part I) 30kgf/cm2

Elongation at Break 12.5µm to bu not

including 75µm Table-2.Cl. 4.3.1 350% (Min) IS : 3400 (Part I) 260%

Elongation at Break above 75µm Table-2.Cl. 4.3.1 400% (Min) IS : 3400 (Part I) 420%

DAM GATE SEAL

Dam Gate Seal as per IS:11855

SANDHYAFLEX Bulb Seal/ Side Seal

25Diax 70x10mm Bulb Seal

Size: Bulb Dia. 33mm X 90mm wide C 10mm thick s

Bulb seal with 44mm bulb dia X 125mm width

BULB DIA 36 X 12 MM TH STEM X 80 MM

PTFE / Teflon Coated Bulb Type Rubber Seal

44mm Bulb Da x 14mm Thick x 127mm Width

44mm Dia x 14mm Thick x 100mm Widh

Bulb seal with 44mm bulb dia X 125mm width

J/P TYPE SOLID BULB RUBBER SEAL 100 X 50 Dia Bulb X 16 MM,

P/J Type Solid Rubber Seal 45x20x150

Z Tyoe Seal 130x20

45x14x45 Bulb Seal

T F Double Bulb Seal 45x20x150mm

50mmBulb x 125x20mm

SANDHYAFLEX Double Steam Bulb Seal as per IS:11855

25mmBulbx 100x10mm

36mm Bulb x 125x12mm


45mmBulb x 150x16mm

50mmBulb x 200x20mm

SANDHYAFLEX Bottom Seal as per IS:11855

10 MM THK X 75 MM WIDE

14mm Thick x85mm Width

20mm Thick x 100mm Width

20mm thick X 125mm width

75mm wide X 16mm thick

100x10 Bottom Seal

100 x 14 Bottom Seal

110x20 Bottom Seal

70x10 Bottom Seal

SANDHYAFLEX CORNER SEAL as per IS:11855

Bulb x16 MM X 400 X 400 MM

25mmBulb x 250x250mm


50mm Dia 44mm bulb dia X 125mm width X 300mm long X 12mm thick

Corner Seal ‐45x400x400

50mmBulbx500x500mm

TEST REPORT

S. No Tests


Clause Number






Hardness Test Cl.2.1 60 to 70 Shore A IS : 3400 (Part II) 65 Shore A

Tensile Strength Cl.2.1 14.5 N/mm2 (Min) IS : 3400 (Part I) 16.5N/mm2

Elongation at Break Cl.2.1 450% (Min) IS : 3400 (Part I) 500%

2 Water Absortion Cl.2.1 10% (max) IS : 3400 (Part VI) 5.80%

3 Polymer Percentage Cl.2.1 70 % (Min) IS : 3400 (Part XXII) 71.50%

4 Polymer Cl.2.1 (NR) ASTM D297 NR

5 Physical Properties - After Ageing @ 70oC for 48 Hours

Change in Hardness Cl.2.1 + 20%(Max) IS : 3400 (Part IV) + 7 Deg

Change in Tensile Strength % Cl.2.1 - 20 % (Max) IS : 3400 (Part IV) - 7.35%

Change in Elongation at Break in %

Cl.2.1 - 20 % (Max) IS : 3400 (Part IV) - 12.15%

6 Low Temperatuer Brittleness for 3Min

Cl.2.1 Should No any Defect

Annexure A Testes and Found OK

PIPE LINE DI PIPE GASKET


DI Pipe Gasket (EPDM TYTON) as per IS:5382‐2003 Specification:

Size:80mm To 2000mm

For Type 2

Hardness‐ 50 Shore A

Tensile Strength‐11.0MPa

Elongation at Break‐400%

For Type 5

Hardness‐ 80 Shore A

Tensile Strength‐9.0MPa

Elongation at Break‐125%

Cement Feeding Rubber Hose


Cement Feeding Rubber Hose as per IS:5137:990 Specification:

Size: 3” ID to 16” ID

End Fitting: MS Flange as per ASA 150 # ANSI 16.5 Drilled and DIN Specification.

Working Pressure ‐10 to 15kg/cm2

Color: Black

Vaccum:500 to 700hg

Temperature‐ 150Deg C

Top: Plain and Corrugated.

Lining : Synthetic Rubber High Ablation Resistance.

Reinforcement: High Quality and Heat Resistance Fabric and Tyre Cord Reinforcement.

Helical Wire: 16 WWG to 8 SWG High Tensile Spring Helical Wire

Cover: Weather Resistance Synthetic Rubber

REGULAR SIZE:

SANDHYAFLEX‐CFRH‐80NB‐3Inch ID









TEST REPORT

S. No

Tests IS:5137:1990 Clause

Number


IS:5137:1990 Specification



1 Physical Properties - Lining Before Ageing

Tensile Strength Table-2,Cl.4.3.1 14.0 MPa (Min) IS : 3400 (Part I) 15.5 MPa

Elongation at Break Table-2,Cl.4.3.1 500% (Min) IS : 3400 (Part I) 540%

2 Physical Properties -Cover Before Ageing



3 Physical Properties - Lining After Ageing @ 72h at 70 + 1oC

Change in Tensile Strength

% Table-2,Cl.4.3.1 +25% (Max) IS : 3400 (Part IV) -18.85%

Change in Elongation at

Break in % Table-2,Cl.4.3.1 +10/ -30 % (Max) IS : 3400 (Part IV) -.13.94%

4 Physical Properties - Cover After Ageing @ 72h at 70 + 1oC





5 Adhesion Table-3,Cl.4.4.1 2.0 kN/m(min) IS : 3400 (Part IV) 2.8 kN.m

Bulker Unloading Cement Fly Ash Rubber Hose

Sandhya Enterprises AN ISO:9001;2015 Certified Company is manufacture and Supplier of Bulker

Unloading Cement Fly Ash Rubber Hose as per IS:5137:990 Specification:




Color: Black

Vaccum:500 to 700hg





Helical Wire: 16 WWG to 8 SWG High Tensile Spring Helical Wire


SANDHYAFLEX‐BUCFFARH‐80NB‐3Inch ID




TEST REPORT

S. No


Number






















Slurry and Mud Rubber Hose

Sandhya Enterprises AN ISO:9001;2015 Certified Company is manufacture and Supplier of Slurry and

Mud Rubber Hose as per IS:5137:990 Specification:




Color: Black

Vaccum:500 to 700hg





Helical Wire:10 WWG to 8 SWG High Tensile Spring Helical Wire


REGULAR SIZE:

SANDHYAFLEX‐SMRH ‐150NB ‐6 Inch ID



TEST REPORT

S. No


Number






















Road and Rail Tanker Oil Suction and Discharge Rubber Hose

Sandhya Enterprises AN ISO: 9001;2015 Certified Company is manufacture and Supplier of Road and

Rail Ranker Oil Suction and Discharge Rubber Hose as per IS:10733 Specification:

Construction: The tube of fuel dispensing hoses contains uniform seamless lining of top quality rubber that is completely resistant to petroleum products.

Reinforcement : Plies of woven textile which contains rubber on both the sides. It is supported by the helical GS wire included in fabric plies.

Electrical Bonding : Low resistant electrical bonding wire is in incorporated between the reinforcement plies to provide electrical continuity along the whole length of the hose.

Cover: a great smooth synthetic compound which is highly resistant to extreme weather, abrasion, petroleum products, wear and tear.

End Connection : The hose is available with or without flanges and with built in nipples.

APPLICATION The application is in applying the petroleum products from road rail tanker carrying these products. It is mainly used for the loading and unloading of the products such as petrol and diesel.

TECHNICAL SPECIFICATION

SIZE Working Pressur

e 7

Kgf/cm2

Bursting Pressur

e 28

Kgf/cm2

Working Pressur

e 10

Kgf/cm2

Bursting Pressur

e 40

Kgf/cm2

Working Pressur

e 15

Kgf/cm2

Bursting Pressur

e 60

Kgf/cm2

MM INCH

63.00 2.1/2 8.5 6.5 10.5 8.5 - -

75.00 3 10.0 7.5 12.0 10.0 - -

TEST REPORT

S. No

Tests IS:10733-1983-Type 1B

Clause Number

Permissible Limits as per IS:10733-

1983-Type 1B Specification




Tensile Strength Table-2. Cl.4.4 7.0 MPa (Min) IS : 3400 (Part I) 8.8 MPa

Elongation at Break Table-2. Cl.4.4 250% (Min) IS : 3400 (Part I) 300%


Tensile Strength Table-2. Cl.4.4 7.0 MPa (Min) IS : 3400 (Part I) 8.5 MPa

Elongation at Break Table-2. Cl.4.4 300% (Min) IS : 3400 (Part I) 360%

3 Resistance to Vacuum Cl.4.9 Vacuum of 83kPa

(500mm mercury) for 10 minutes

IS:443-1975 Tested and Found OK

4 Adhesion Test Cl.4.6 4.5Kg IS:3400 (Part V) 5.8kg

5 Swelling Test Cl.4.7 75% (max) IS:3400 (Part VI) 40.20%

6 Fuel Soluble Matter Cl.4.8 5% (max) IS:3400 (Part VI) 3.50%


Change in Tensile

Strength % Table-2.Cl..4.5 + 25.0%(Max) IS : 3400 (Part IV) -12.85%


Break in % Table-2.Cl..4.5 +10/ - 15 % (Max) IS : 3400 (Part VI) -.11.94%


Change in Tensile

Strength % Table-2.Cl..4.5 +10/-15 % (Max) IS : 3400 (Part IV) -11.25%


Break in % Table-2.Cl..4.5 +10/ - 15 % (Max) IS : 3400 (Part IV) -11.25%

Oil Suction and Discharge Discharge Rubber Hose

Sandhya Enterprises AN ISO:9001;2015 Certified Company is manufacture and Supplier of Oil

Suction and Discharge Rubber Hose as per IS:8189 Specification:

Construction: The tube of fuel dispensing hoses contains uniform seamless lining of top quality rubber that is completely resistant to petroleum products.

Reinforcement : Plies of woven textile which contains rubber on both the sides. It is supported by the helical GS wire included in fabric plies.

Electrical Bonding : Low resistant electrical bonding wire is in incorporated between the reinforcement plies to provide electrical continuity along the whole length of the hose.

Cover: a great smooth synthetic compound which is highly resistant to extreme weather, abrasion, petroleum products, wear and tear.

End Connection : The hose is available with or without flanges and with built in nipples.

APPLICATION The application is in aupplying the petroleum products from road rail tanker carrying these products. It is mainly used for the loading and unloading of the products such as petrol and diesel.


SIZE Working Pressure

7 Kgf/cm2

Bursting Pressure

28 Kgf/cm2

Working Pressure

10 Kgf/cm2

Bursting Pressure

40 Kgf/cm2

Working Pressure

15 Kgf/cm2

Bursting Pressure

60 Kgf/cm2

MM INCH

63.00 2.1/2 8.5 6.5 10.5 8.5 - -

75.00 3 10.0 7.5 12.0 10.0 - -

100.00 4 15.0 11.0 18.0 14.0 - -

150.00 6 30.0 22.5 36.0 24.0 48.0 31.5

200.00 8 45.0 28.5 51.0 36.0 63.0 43.5

250.00 10 - - 66.0 49.0 78.0 66.0

300.00 12 -

TEST REPORT

S. No

Tests IS:8189-1996 Clause

Number

Permissible Limits as per IS:8189-1996

Specification




Tensile Strength Table-1. Cl.5.1.1.3 7.0 MPa (Min) IS : 3400 (Part I) 8.8 MPa

Elongation at Break Table-1. Cl.5.1.1.3 250% (Min) IS : 3400 (Part I) 300%


Tensile Strength Table-1. Cl.5.1.1.3 7.0 MPa (Min) IS : 3400 (Part I) 8.5 MPa

Elongation at Break Table-1. Cl.5.1.1.3 300% (Min) IS : 3400 (Part I) 360%

3 Resistance to Vacuum Cl.4.9 Vacuum of 83kPa

(500mm mercury) for 10 minutes

IS:443-1975 Tested and Found

OK

4 Adhesion Test Cl.4.6 4.5Kg IS:3400 (Part V) 5.8kg

5 Swelling Test

Lining Table-1. Cl.5.1.1.3 30% (max) IS:3400 (Part VI) 15.25%

Cover Table-1. Cl.5.1.1.3 100% (max) IS:3400 (Part VI) 65.20%

6 Fuel Soluble Matter Table-1. Cl.5.1.1.3 3% (max) IS:3400 (Part VI) 2.25%


Change in Tensile



Break in % Table-2.Cl..4.5 +10/ - 40 % (Max) IS : 3400 (Part VI) -.22.94%


Change in Tensile



Break in % Table-2.Cl..4.5 +10/ - 40 % (Max) IS : 3400 (Part IV) -23.25%

Water Suction and Discharge Rubber Hose

WATER SUCTION & DISCHARGE HOSE, HEAVY DUTY TYPE 1 ROUGH BORE, TYPE 2 SMOOTH BORE CONFORMING TO IS 3549/1983 APPLICATION Water suction and discharge hose is designed for various applications that involve the suction and discharge of waste water, mud and sewage. The hose posses very flexible structure and properties so that it can be used in adverse conditions. The material used in manufacturing of it is resistant to

abrasion and unwanted material. It can be used for deflooding, suction of waste water in construction works, mines and other heavy duty operations that involve removal of mud and waste water.

There are two types of hoses: Type I comes with rough bore TYpe II comes with smooth bore


SIZE W. P. 7 Kgf/cm2 W. P. 10 Kgf/cm2 W. P. 15 Kgf/cm2

MM inch Proof

Pressure Kgf/cm2

Bursting PressureKgf/cm2

Proof PressureKgf/cm2

Bursting Pressure Kgf/cm2



38.00 1.1/4 10.5 21 15 30 22.5 45

50.00 2 10.5 21 15 30 22.5 45

63.00 2.1/2 10.5 21 15 30 22.5 45

75.00 3.0 10.5 21 15 30 22.5 45

100.00 4.0 10.5 21 15 30 22.5 45

100.00 5.0 10.5 21 15 30 22.5 45

150.00 6.0 10.5 21 15 30 22.5 45

200.00 8.0 10.5 21 15 30 22.5 45

250.00 10.0 10.5 21 15 30 22.5 45

300.00 12.0 10.5 21 15 30 22.5 45

Water Delivery Rubber Hose Pipe

Enterprises AN ISO:9001;2015 Certified Company is manufacture and Supplier of Water

Delivery Rubber Hose Pipe Specification:


EWorking Pressure ‐2.5 to 5kg/cm2

Color: Black


Top: Plain

Lining : Synthetic Rubber High Water Resistance



REGULAR SIZE:










SAND BLASTING RUBBER HOSE

RUBBER HOSE FOR SAND BLASTING As per IS 5894/90

APPLICATION These rubber hose for sand and blasting are used to carry the abrasive material such as sand at a very high pressure. The application is in ordinance factories, manufacturing workshops and other heavy engineering realted works. The level of strength os this hose is very high so that it can satisfy the need of the work. Manufactured to provide the top quality to the hose.


SIZE TYPE-I TYPE-II

MM INCH Working Pressure Kgf/cm2



Working Pressure Kgf/cm2



12.50 1/2 7 17.5 35 10 25 50

20.00 3/4 7 17.5 35 10 25 50

25.00 1.0 7 17.5 35 10 25 50

31.50 1.1/4 7 17.5 35 10 25 50

38.00 1.1/2 7 17.5 35 10 25 50

45.00 1.3/4 7 17.5 35 10 25 50

50.00 2.0 7 17.5 35 10 25 50

63.00 2.1/2 7 17.5 35 10 25 50

75.00 3.0 7 17.5 35 10 25 50

Chemical Rubber Hose

The rubber hose for chemicals are specially designed for the transfer of chemicals and acids. They are apt for any kind of apllication where chemicals are transferred through suction or pumping. Now chemical rubber hoses have to bear abrasion, heat and many more aggressive and adverse conditions so these are designed using high quality synthetic rubber.

Rubber hose is designed to carry material/chemicals in the factories during the production process. Our premium quality rubber hoses are resistant to the material they are carrying. We are one of the best brands in the area of rubber hose manufacturing and our products are trusted worldwide.

APPLICATION Transfer of acids and chemicals through pumping, suction and discharge.


SIZE No. of BRAND PLY

MM INCH

12.50 1/2 2 2

20.00 3/4 2 3

25.00 1 2 3

31.50 1.1/4 2 3

35.00 1.3/8 2 3

38.00 1.1/2 2 3

45.00 1.3/4 2 3

50.00 2 3 4

56.00 2.1/4 3 4

60.00 2.3/8 3 4

63.00 2.1/2 3 4

70.00 2.3/4 - 4

75.00 3 - 5

88.00 3.1/2 - 5

100.00 4 - 5

112.00 4.1/4 - 5

125.00 5 - 6

150.00 6 - 7

200.00 8 - 10

250.00 10 - 10

300.00 12 - 12

Carbon Free Rubber Hose

CARBON FREE RUBBER HOSE

Carbon free rubber hoses are available with or without asbestos cover both.

APPLICATION SThese are specially designed hoses to carry cables that can conduct upto 11KVA and above.

FEATURES A synthetic carboon free white tube is used inside to provide the strength and resistance against high heat and electricity. Asbestos cover is provided on the outer side for longer life. Can handle the working pressure ranging from 7 kg/cm2 to 15 kg/cm2


Nominal bore

(in mm)

Tolerance on

Nominal bore

(in mm)

Number of reinforcement

(ply)

Working Pressure

(Kg.f/cm2)

Testing Pressure

(Kg.f/cm2)

Bursting Pressure

(Kg.f/cm2)

12.5 0.75 3 10 20 40

16.0 0.75 3 10 20 40

20.0 0.75 4 10 20 40

25.0 1.25 4 10 20 40

28.0 1.25 4 10 20 40

31.0 1.25 4 10 20 40

35.0 2.00 4 10 20 40

38.0 2.00 4 10 20 40

50.0 2.00 5 10 20 40

56.0 2.00 5 10 20 40

60.0 2.50 5 10 20 40

63.0 2.50 6 10 20 40

70.0 2.50 6 10 20 40

75.0 2.50 6 10 20 40

88.0 2.50 6 10 20 40

100.0 2.50 6 10 20 40

TEXTILE BRAIDED AIR RUBBER HOSE

APPLICATION Rubber Air Hose have numerous applications in pneumatic industry. Type-I and Type-II can be used for various purposes. These hoses comes with strength and endurance that is needed in applications related to compressor and pneumatics. These can be used in various types of compressors.

HYDROSTATIC TESTING The standard stock lengths that are available with us to satisfy your needs are 50 ft, 75 ft and 100 ft.

TYPE-I TYPE-II TYPE-III

SIZE MM INCH



Working PressureKgf/cm2




1/4 7 28 10 40 14 56

5/16 7 28 10 40 14 56

3/8 7 28 10 40 14 56

1/2 7 28 10 40 14 56

3/4 7 28 10 40 14 56

1 7 28 10 40 14 56

1.1/4 7 28 10 40 14 56

1.1/2 7 28 10 40 14 56

2 7 28 10 40 14 56

2.1/2 7 28 10 40 14 56

3 7 28 10 40 14 56

SIZE No. of BRAID

MM INCH

06.30 1/4 1

08.00 5/16 1

10.00 3/8 1

12.50 1/2 1

20.00 3/4 1

25.00 1 2

31.00 1.1/4 2

38.00 1.1/2 2

50.00 2 3

63.00 2.1/2 4

75.00 3 4

WELDING RUBBER HOSE as per IS:447:1988

Applications: Rubber air hose for welding is used for wide variety of applications in welding and gas cutting operations. It is suitable for any type of industry where welding is required. It is very popular in automobile industry.

Construction Tube This type of hose is manufactured using synthetic and natural rubber both and has uniform thickness throughout the hose. The covering is plain and smoothly finished and provides high tensile strength due to the use of synthetic yarn.

Reinforcement High Tensile Synthetic yarn.

Cover Blend of Natural & Synthetic rubber. Finish - Plain, Smooth, Fluted, Wrap finish.

Color Blue color is used for oxygen and non fuel gases whereas the red color is used for fuel gases.

Temp Can handle temperature from 400F to +1600F


SIZE MM

Working PressureKgf/cm2



5.0 12.5 25.0 50.0

6.3 12.5 25.0 50.0

8.0 12.5 25.0 50.0

10.0 12.5 25.0 50.0

12.5 12.5 25.0 50.0

RUBBER EXPANSION BELLOW

Sandhya Enterprises AN ISO:9001;2015 Certified Company is manufacture and Supplier of Rubber

Expansion Joint Bellow per customer Specification:

We offer ranges of standard as well as custom manufactured bellows to cater for many applications

from heavy industry to food quality . The selection of bellows design, open:close ratios, stroke

length, convolution width, split or endless configuration, and materials will depend on your specific

application.

Where molded bellows are not suitable, a range of hand-built rubber bellows are available

including tapered and smooth bore.

Our hand-built rubber bellows are designed to absorb motion and displacement between pipe

flanges.

For more than 50 years, Shah India Rubber has stood at the forefront of fluid sealing technology.

Our history of growth and success is rooted in our commitment to deliver the most innovative

sealing solutions and unparalleled service to the worldâ€™s processing industries.

Rubber Expansion Joints protect equipments and piping from damage caused by vibration and

thermal movements. While not their primary purpose, they are also frequently used to

accommodate equipment misalignments. Rubber expansion joints provide superior flexibility,

movement absorption, and cycle life, while resisting chemical attack and abrasion.

They are useful over a wide range of temperatures & pressures, making them the preferred

expansion joint for most liquid and slurry applications, though gases & solids are also frequently

conveyed by rubber expansion joints. Function of rubber expansion joints :

Damp oscillation, noise and vibration

Compensate motion

Compensate expansion caused by differences in temperature

Reduce tension

Compensate ground and foundation settling

Compensate imprecise assembly

Serve as assembly and disassembly aids

Provide an elastic wall seal for penetration assemblies

Compensate pipeline movements Three features set Industrial Moulders Expansion Joint technology apart :

Screen Vibrating Rubber Beading

Sandhya Enterprises AN ISO:9001;2015 Certified Company is manufacture and Supplier of Screen

Vibrating Rubber Beading per customer Specification:

1. Vibrating Screen Rubber Beading for Wire Mesh Regular size: Gap‐10mmm Dia‐35mm, Hight‐52mm


3 Vibrating Screen Rubber Beading for Wire Mesh Regular size: Gap‐7mmm Dia‐29mm, Hight‐43mm


Rubber Cord

Sandhya Enterprises AN ISO: 9001;2015 Certified Company is manufacture and Supplier of Rubber

Cord as per Customer Requirement.

Size:2mm Dia to 100mm Dia

Hardness:25 to 80 Shore A

NR Rubber Cord

NBR Rubber Cord

Neoprene Rubber Cord

SBR Rubber Cord

EPMD Rubber Cord

Sponge Rubber Cord

RUBBER STRIP

Sandhya Enterprises AN ISO: 9001;2015 Certified Company is manufacture and Supplier of Rubber

Strip as per Customer Requirement.

Hardness:25 to 80 Shore A

NR Rubber Strip

NBR Rubber Strip

Neoprene Rubber Strip

SBR Rubber Strip

EPMD Rubber Strip

Sponge Rubber Strip

RUBBER SPEED BREAKER

We Are The Leading Manufacturer of Speed Breaker in India. SANDHYA ENTERPRISES Safety Solutions Have 20 Years good experience to provide all this material.

We have been able to Manufacturer of Speed Breaker in India cater to the various requirements of clients by providing a wide array of Rubber Speed Breker. Highly resistant to brutal weather conditions and various impacts, these Rubber Speed Breaker are manufactured using superior-grade Rubber that is obtained from reliable vendors of the industry. Easy in installation, our offered Rubber Speed Breaker are modular and compact in design, which has affixed night vision reflectors with glass metals on both sides of Rubber Speed Breaker Ours is a prominent name of the industry, which is engaged in manufacturing, supplying, a qualitative range of Rubber Speed Breakers. The offered array of Rubber Speed Breakers is manufactured by our professionals in complying to the international standards of quality. These speed breakers help in controlling traffic and accidents in roads. Further, our respected customers can avail these speed breakers from us at industry leading prices. Speed Breakers : shiv safety solutions is the leading Manufacturer of Speed Breaker in India.We have wide range of speed breakers Size 350 mm x 500 mm x 50 mm,

material : rubber. color – yellow black with reflective cat eyes

Rubber Conveyor Belts

Rapid industrialisation has necessitated the use of conveyor Belts which have proved to be the most cost-effective system for transportation of raw material & finished goods in any form, for any application. SANDHYA ENTERPRISES belting are manufactured in our most modern, fully automated plant, using the finest raw material inputs, under the strict vigil of qualified technical personnel. Our Belts have found satisfactory customers in the Domestic and the International export market with our clientele ranging Iron & Steel Plants, Coal, Copper, Gold Mines, Cement Plants, Thermal Plants, Fertilizers Plant and Ports to name a few.SANDHYA ENTERPRISES Conveyor Belts conform to all relevant Indian/International Standards and are manufactured in a wide range to suit all applications.

SPECIAL FEATURES Unique Carcass Construction Superior Adhesion Levels Improved Flex Life Low Belt Stretch Excellent Impact Resistance Improved Resistance to Mechanical Damage Mildew, Moisture & Rot Resistance Improved Resistance to Ozone and Ultra Violet Radiation Improved Efficiency of Joints Improved Tear Resistance & Excellent Troughability Suitable for all Applications

ANTI VIBRAITION RUBBER PAD

andhya Enterprises AN ISO: 9001;2015 Certified Company is manufacture and Supplier of Anti

Vibration Rubber Pad as per Customer Requirement.

Size:1.150x150x12mm

2.150x150x25mm

SANDHYA ENTERPRISES

Documents

Transcript of SANDHYA ENTERPRISES