Assembly Instruction TWIN - FULL BUNK BED

Assembly Instruction TWIN - FULL BUNK BED

TWIN - FULL BUNK BED HARDWARE LIST

NO DRAWING DESCRPTION QTY

1 onimmixce 80mm Bolt 22 pcs

2 11(81(818(n 60mm Bolt 10 pcs

3 30mm Bolt 12 pcs

4 32mm Screw 16 pcs

5 Allen Key M4 1 pc

NO DRAWING DESCRPTION QTY

6 -4i1K*0 30mm Screw 50 pcs

7 .0g010 16mm Screw 2 pcs

8 Wood Dowel 010 x 30mm 40 pcs (-(0

9 Barrel Nut M6 x 13mm 32 pcs

10 Metal Pin

09.5 x 127mm 4 pcs 0 )

NOTE : A screwdriver will be needed to tighten all wood screws.

Replacement Parts Request : Please advise part number from the above hardware list.

MADE IN MALAYSIA

TWIN - FULL BUNK BED ASSEMBLY PAGE 1


IMPORTANT: Unpack All Parts & Organize Before Assembly!!!

TWIN-FULL BUNK BED COMPONENT LIST

PART DRAWING DESCRPTION QTY PART DRAWING DESORPTION QTY

A Headboard

(Upper) 1 pc K Guard Rail

(Front) pcs 2 p 113Z111131111 .• .1

B L Guard Rail

Support 3 pcs Footboard

(Upper) 1 pc 1131331 I. • • i

C M iiiiiii 1;11;1111111111111 111111

Slat (Upper) 1 set

Headboard (lower) 1 pc 1 11:13:13:1111 i

ponniimunq

D Footboard

(Lower) 1 pc 1 1111111111111111111 1 1111111111

i iiiiiiiii lir Slat

(Lower) 1 set 113:111:13:13:11 11111111111111111111

E Center Rail 1 pc O Ladder Leg (Upper-Left) 1 pc l y 1

F Side Rail

(Lower Front) 1 pc Ladder Leg

(Upper-Right) 1 pc I ' 1

G Side Rail

(Lower Rear) 1 pc Q

Ladder Leg Lower

(Left & Right) 2 pcs (•• p-1 I I

H Side Rail

(Upper front) 1 pc Ladder Stretcher (Upper & Middle) 3 pcs I : : I J

1 Side Rail

(Upper Rear) 1 pc Ladder Stretcher (Lower)

1 pc I I I I

J Guard Rail

(Rear) 2 pcs T Support Panel 1 pc

MADE IN MALAYSIA

TWIN - FULL BUNK BED ASSEMBLY

PAGE 2

TWIN - FULL BUNK BED Assembly Instruction

STEP 1 Insert wood dowels, insert barrel nut into hole

& insert bolt from outside.

1

1

1 _

/

/ /

/ 1

/ I / \

L 1- 1-

L__ ,

8

L Align bolts to connect with barrel nut & tighten.

Cleaning Instructions : After assembly, clean & polish with a soft cloth. TWIN - FULL BUNK BED ASSEMBLY

PAGE 3

TWIN - FULL BUNK BED Assembly Instruction

STEP 3

Insert bolts to connect with barrel nut & tighten. Remember to insert wood dowels also for alignment & strength.

Cleaning Instructions : After assembly, clean & polish with a soft cloth.


r 1

L


STEP 5

Insert metal pin, align & stack twin bed.

CAUTION: Please be careful not to pinch your fingers.

STEP 6

Insert bolt to connect with barrel nut & tighten. Remember to insert wood dowel for alignment & strength.

Cleaning Instructions : After assembly, clean & polish with a soft cloth.


STEP 8

Please follow the pilot hole at right ladder rail.


Cleaning Instructions : After assembly, clean & polish with a soft cloth. TWIN - FULL BUNK BED ASSEMBLY

PAGE 6

Assembly Instruction TWIN - TWIN BUNK BED

SAFETY WARNING

Read all instructions carefully before assembling this product.

1. Follow the information on the warnings appearing on the upper bunk end structure and on

the carton. Do not remove warning label from bed.

2. Always use the recommended size mattress or mattress support, or both, to help prevent

the likelihood of entrapment or falls.

3. Surface of mattress must be at least 5 in. (127 mm) below the upper edge of guardrails.

4. Do not allow children under 6 years of age to use the upper bunk.

5. Periodically check and ensure that the guardrail, ladder, and other components are in their

proper position, free from damage, and that all connectors are tight.

6. Do not allow horseplay on or under the bed and prohibit jumping on the bed.

7. Prohibit more than one person on upper bunk.

8. Always use the ladder for entering and leaving the upper bunk.

9. Do not use substitute parts. Contact the manufacturer or dealer for replacement parts.

10. Use of a night light may provide added safety precaution for a child using the upper bunk.

11. Always use guardrails on both long sides of the upper bunk. If the bunk bed will be placed

next to the wall, the guardrail that runs the full length of the bed should be placed against

the wall to prevent entrapment between the bed and wall.

12. The use of water or sleep flotation mattresses is prohibited.

13. STRANGULATION HAZARD-Never attach or hang items to any part of the bunk bed

that are not designed for use with the bed; for example, but not limited to hooks, belts

and jump ropes.

14. Keep these instructions for future reference.

SIZE OF MATTRESS AND FOUNDATION:

• Use a mattress which is 37 1/2" - 38 1/2" wide and 74"-75" long on upper bunk (twin size.)

• Ensure that the thickness of the mattress does not exceed 7" and that the mattress surface is at least 5" (127mm) below the upper edge of the guardrails.

• Use a mattress which is 38" wide and 75" long on lower bunk (twin size). • Ensure that the thickness of the mattress is at least 7".

WARNING:

Adult Assembly Required. This package contains small parts. Keep away from children.

Replacement Parts:

IMPORTANT: ALL CONNECTIONS MUST BE TIGHTENED PROPERLY

Assembly Instruction TWIN - FULL BUNK BED

Documents

Transcript of Assembly Instruction TWIN - FULL BUNK BED