psm2200 Ordering Information - Primion

psm2200Ordering Information

Valid from: April 2020

pdf Innenseiten Beschnitt: außen 3 mm – innen 0mm

System requirements

1. Hardware requirements

1.1 General notes❱ The system requirements of the OS and the DBMS

must be taken into account when sizing the computer(s).❱ The exact requirements of the drivers can be found

in the corresponding documentation and must also be taken into account

1.2 ServerIn the case of the Server, it should be ensured that it offers a true server structure, e.g. Intel Xeon.We recommend the following sizes for a complete psm server, i.e. Database server and Apache Tomcat:❱ CPU: QUAD > 3 GHz or more❱ RAM: 64 bit system: at least 16 GB❱ Hard disc storage:

At least 500 GB of free hard disc storage is required (redundant via Raid 1 or 5 or better).

❱ Network interface with at least 1 GBit/sec.❱ The required interfaces (COM, Ethernet, USB)

are dependent on the driver(s) that are in use. Please refer to the corresponding driver documentation.

1. The requirements in terms of the server hardware are very much dependent on the systems that are connected. The system requirements of the connected systems must be taken into account here.

2. NVR-CCTV video systems must be operated on separate hardware, including network and must not be located on the server.

3. Chapter “Client” (Chapter 1.3) must be noted if client applications should also run on the server.

1.3 ClientWe recommend the following sizes for a client:❱ CPU: at least 3 GHz❱ RAM: 32 bit system (x86 computer): 4 GB

64 bit system: at least 16 GB❱ Hard disc storage:

At least 500 GB of free hard disc storage is required. ❱ Graphic card: DVI, at least 1680 x 1050; Multiple,

depending on the number of required physical monitors with the corresponding number of outputs Please take the requirements of the deployed video system(s) into account, as necessary.

❱ Network interface: at least 1GBit/s❱ Sound card

2. Software requirements

2.1 Server side2.1.1 Operating systemsCurrently, the following operating systems are supported:❱ Windows Server 2008 R2❱ Windows Server 2012❱ Windows Server 2012 R2❱ Windows Server 2016

Chapter “Operating systems” (Chapter 2.2.1) must be noted if client applications should also run on the server.

Virtual operating systems:“VMware” can be deployed as the virtualisation system. Further virtualisation systems on request

Please take note of the following restrictions when deploying virtual operating systems:1. You must ensure that the applications connected to

psm2200 can run on the deployed virtualisation system.2. You must ensure that in the case of serial connections,

the connection to the virtualisation system behaves in the same way as when deployed without visualisation (performance & timing).

3. It may be necessary to reactivate the software licence because the hardware specifications of the virtualisation system can change. The hardware is specified based on the components deployed with the server. For this reason, a new activation, that is to say a new psm2200 licence, is necessary if anything changes in the server constellation. If applications (drivers) are moved, this has no effect on the psm2200 licence.


2.1.2 Supported database management systemsThe following database management systems (DBMS) can be deployed in conjunction with psm2200:❱ H2❱ Oracle from Version 10, 11 and 12 ❱ MS SQL Server 2008, 2008 R2, 2012, 2014, 2016

During the installation, no differentiation is made as to whether an XE version (only for Oracle 10), an Express version or a version requiring a licence is being installed. You should be aware of the restricted sizes of the free-of-charge databases.

Please enquire with your supplier about the suitability of other database management systems.

A pre-prepared, freeware H2 database is supplied with the software.

2.1.3 Web / Application serverTomcatTomcat version 8.0.38 is required. This version is supplied with the software and is installed during the psm2200 installation procedure.

Newer versions have not been tested by us and are therefore not approved by us for use with psm2200. Please enquire with your supplier about the suitability of other web servers . Only the psm2200 Web applications may be operated under the Tomcat for psm2200.

2.1.4 Java Runtime Environment (JRE)The 64 bit version of JRE Version 1.8.0.201 is required. This version is supplied with the software and is installed during the psm2200 installation procedure.

It must be ensured that no automatic Java updates will be carried out.

2.1.5 .NET FrameworkDepending on the driver or plugin, an appropriate .NET Framework (3.5, 4, 4.6.2, ...) is required and is installed largely automatically during the installation process.For this purpose, the psm2200 server may need an Internet connection. Otherwise, the operating system may generate an error during the installation process, which provides information on the correct installation method. This must then be carried out by a system administrator on site to ensure that the system is ready to run.

2.1.6 LDAP / SSOLDAP (username & password) can be used for logging on to psm2200. Single Sign On (SSO) is not supported.

2.1.7 DriversEssentially, each driver has to be considered separately, in order to be able to define the server-based requirements for the proposed psm2200 installation.Different systems are connected to psm2200 over corresponding drivers.Please refer to the appropriate driver documentation to determine the compatibility of the driver to the psm2200 version.

Our general recommendation is that during an update, you should not only update the psm2200 Server and psm2200 Client, but also the corresponding drivers and/or plugins because the individual components are matched to each other.

1. All required drives have to be specified for the generation of the licence file.

2. Redundancy capabilities are dependent on the hardware that is connected and has to be clarified on a case-by-case basis.


2.2 Client side2.2.1 Operating systemsCurrently, the following operating systems are supported:❱ Windows 7 (Professional, Ultimate or Enterprise (min. SP1))

– x86 (32 bit system) – x64 (64 bit system)

❱ Windows 8.1 (Professional, Ultimate or Enterprise) – x86 (32 bit system) – x64 (64 bit system)

❱ Windows 10 (Professional, Ultimate or Enterprise) – x86 (32 bit system) – x64 (64 bit system)

2.2.2 Java Runtime Environment (JRE)The 32 or 64 bit version of JRE Version 1.8.0.201 is required. Newer versions have not been tested by us and are therefore not approved by us for use with psm2200. This version is supplied with the software and is installed during the psm2200 installation procedure.

It must be ensured that no automatic Java updates will be carried out.

2.2.3 .NET FrameworkDepending on the driver or plugin, an appropriate .NET Framework (3.5, 4, 4.6.2, ...) is required and is installed largely automatically during the installation process.The psm2200 Server requires an Internet connection for this purpose. Otherwise, a corresponding error message is generated during the installation process, advising what the correction installation procedure is.This then has to be done by a local System administrator so that an operational system is created.

2.2.4 PluginsFundamentally, each plugin has to be considered separately when it comes to determining the client-based system requirements for psm2200.Different systems are connected to psm2200 through various plugins. Please refer to the relevant plugin documentation for details of the compatibility of the plugin to the psm2200 version.The required DLLs and SDK Redistributables are supplied and installed in a similar way to the driver routine.

The plugins always have to be installed locally on the client device where they are to be used. The plugin folder structure is prescribed by the installation and may not be changed.

2.2.5 Supported audio formatsIn terms of audio files, the file extensions .mp3 and .wav are supported, whereby in both cases, they are only containers for the following codings:❱ mp3 encoding:

Raw MPEG-1, 2, and 2.5 audio; layers I, II, and III; all supported combinations of sampling frequencies and bit rates.

❱ pcm encoding: Uncompressed, raw audio samples

There is a limitation to a maximum file size of 5 MB.


2.2.6 Graphics – Formats and sizesThe following graphic formats are supported:❱ Vector graphics: EMF, WMF and SVG (Standard format)❱ Pixel graphics: JPEG, JPG, GIF, PNG, BMP

In the case of SVG graphics, the pure SVG format is supported up to version 1.1. Embedded pictures within the SVG file are not supported. CSS elements within the SVG graphics are not supported.

No animated GIFs are supported

When generating new background pictures, if these are uploaded from the file system, the system checks whether they are bigger than 25 MB.If this is the case, a corresponding message is output.The size of 25 MB is calculated from the maximum picture size of 3840 x 2160 pixels using the RGB colour model. This means that 3 bytes are available per pixel.

2.2.7 Mobile Clients❱ Android and iOS operating systems are supported:

– min. Android 5 – min. iOS 10

❱ In each case, only the on-board browser is supported: – Chrome (Android) – Safari (iOS)

❱ The mobile client is only supported if you are working with HTTPS communication.

Please be aware that the connection is not secure when using self-signed certificates and warning messages may appear.

Changes have to be made at the psm2200 Server if a Milestone Video System 2013 is being controlled through the Mobile client.

A file with the name “config.properties” has to be created in the “<tomcat>/webapps/psm-server-web/WEB-INF/classes” folder, with the following contents:

# En-/Disables the extended authentication

mechanism for Milestone Mobile Server mobile.

streaming.milestone.extended.auth.enabled=false

Then, Tomcat has to be restarted.

3. Network

3.1 FirewallThe deployed port must be released in the firewall settings. Default is 8080 or 8443 when using HTTPS (ssl).

3.2 ProtocolHessian (binary protocol, Version 3.1.6) is used as the protocol over HTTP or HTTPS.A timeout can be defined in the case of Hessian whereby the default value is 60 seconds. If no response is sent to the client within this time, the client identifies this as a connection fault and attempts to re-establish a connection to the server again after 3 seconds. These times can be redefined by creating a workstation within the psm2200 Configuration client and assigning it to the system user.Alternatively, the workstation can also be assigned through the psm2200 control centre client.

3.3 BandwidthPlease refer to Chapter “Server” (Chapter 1.2) and Chapter “Client” (Chapter 1.3) respectively for the required bandwidths for the Server and Client computers.

4. Operation of psm2200 in accordance with VdS 3534, EN 50518-2

The H2 database has to be operated in embedded mode for the operation of psm2200 to be VdS-compliant. This is ensured by the installation program with the “VdS” option is activated.

A process to monitor the NTP Time synchronisation has to be set up in psm2200 for the operation to be VdS-compliant. The NTP Time synchronisation driver is available for this purpose. Here, the NTP Network Time Protocol (S321-006.001) must also be ordered.


S301-000.02 psm2200 Server – Basic licenceIs required for the activation of the psm2200 Hazard Management System Server. Scope of delivery: Licence-free H2 database; licence for the operation of one physical monitor, Software modules: psm2200 Configuration, psm2200 Graphics Editor, psm2200 Control centre for operation with one concurrent user.A maximum of 3 further physical monitors are possible per client PC. These connection options have to be ordered separately under the part numbers: S310-006.01, S310-007.01, S310-008.01 In this way, graphic visualisation is possible on a maximum of 4 physical and 5 virtual monitors, per workplace.Note:The basic licence does not include any datapoints. These have to be ordered separately. You can order the datapoint packages under the part numbers S310-001.02 and S310-002.02 as required.

S309-000.00 psm2200 Software updateFrom customer psm2200 version to the current psm2200 version

S310-003.02 Concurrent Client (2 - 99) – Expansion by one further ClientEnables the parallel operation of a further concurrent client. The client is called either from any PC, through Java Web Start or from the psm2200 server PC.

S310-010.02 Mobile Client – Expansion by one further Mobile Client Enables the parallel operation of a further concurrent Mobile Client (iOS / Android) With the “Mobile Client” WebApp, the functionality, GUI and menu guidance have all been modified to meet iOS and Android specifications and so that they fit to the display. For the sake of clarity of operation, we recommend the use of a tablet/iPad.Note 1:Supported operating systems: From iOS 10; from Android 5;The mobile client is only supported if you are working with HTTPS communication. psm2200 supports the operation of a maximum of 10 concurrent mobile clients. Note 2:Only the on-board Web browsers are supported, i.e. Safari & Chrome.Workflows for the Mobile client are created using HTML5.Note 3:Supported video plugins: Axis, HeiTel, Milestone. If it is planned to operate several concurrent Mobile Clients, the corresponding number of individual licences has to be ordered.

S310-006.01 psm2200 Multi graphic 2 (2nd monitor connection)Licence for 2nd monitor.Enables the operation of a 2nd physical monitor per workplace PC. Please note that the PC must be set up for the deployment of multiple monitors.

S310-007.01 psm2200 Multi graphic 3 (3rd monitor connection)Licence for 3rd monitor.Enables the operation of a 3rd physical monitor per workplace PC. Please note that the PC must be set up for the deployment of multiple monitors.

S310-008.01 psm2200 Multi graphic 4 (4th monitor connection)Licence for 4th monitor. Enables the operation of a 4th physical monitor per workplace PC. Please note that the PC must be set up for the deployment of multiple monitors.

Licences


Licences

S310-001.02 Licence package for 250 datapoints (up to 1,000 datapoints)Datapoint package for need-based assignment throughout the psm2200 Server, based on the interfaces connected. The psm2200 Server calculates the number of datapoints for each deployed driver.

S310-002.02 Licence package for 250 datapoints (from 1,001 datapoints)Datapoint package for need-based assignment throughout the psm2200 Server, based on the interfaces connected. The psm2200 Server calculates the number of datapoints for each deployed driver.

S330-001.01 Gateway – psm2200 Server standaloneEnables the operation of a psm2200 Server, without graphic visualisation. This option facilitates the provision of datapoint information from connected systems, e.g. prime WebSystems that communicates with protocols such as BACnet, OPC or ESPA. The set-up of the basic system, service functions, logging or the representation of datapoint status information from the psm2200 gateway server are done through the configuration client. Note:In Gateway operation, the psm2200 Graphic editor and the psm2200 Control centre software modules are not available.You can order the datapoint packages under the part numbers S310-001.02 and S310-002.02 as required.The corresponding standard protocol connection, e.g. OPC Server has to be ordered separately.

S330-004.01 Driver redundancyEnables the operation of driver redundancy. For example, a second, independent, monitored driver can be connected and operated in parallel to a driver that is already connected. If either one of the driver connections fails, the other one takes over the communication and increases system drop-out security. Pre-requirement: The hardware that is to be connected has a second driver connection available.Note:A second serial essernet® interface with micro-module is required for the operation of a redundant Esser connection. The Esser order number is 784856. A second IGIS Loop Controller interface is required for the operation of a redundant Honeywell intrusion panel connection The following types are supported: MB / HB 48, MB / HB 100, MB 256. There is an option to upgrade the MB256 to MB 256 plus with an upgrade kit.You can order the datapoint packages under the part numbers S310-001.02 and S310-002.02 as required.


S330-009.01 VdS 3534, EN 50518-2Option for the psm2200 Basic licence. Enables the operation of psm2200 in accordance with VdS 3534 and as a result, opens up application areas where a tested software is demanded, e.g. in Security Command and Control Centres (EN 50518-2), national authorities, in high-security areas, etc.Pre-requirement for operation in accordance with VdS 3534 (EN 50518-2)1. NTP Time synchronisation. Here, the NTP Network Time Protocol (S321-006.001) must also be ordered. 2. The approval is restricted to operation with an H2 database. Oracle and MS SQL are not possible. 3. The driver deployed in the VdS 3534 has to be extended for the VdS 3534 option.

S330-002.01 NotificationOption for the psm2200 Basic licence. Enables the sending and receiving of SMS and e-mail messages, as well as the sending of faxes with graphics. There is an option to send e-mails with attachments. Incoming e-mails and SMS messages are documented in the alarm stack. Their contents can be evaluated, in order to initiate corresponding server scripts or workflows. Pre-requirements: E-Mail: SMTP server with IMAP / POP3 protocol. SMS: Additional hardware: Cinterion MC55i terminal.

S330-007.01 Client data separationOption for the psm2200 Basic licence. Enables the structuring of the psm2200 system with different users/clients, without them being able to view each other’s data. In this way, different applications can be set up on one psm2200 server for different users, each with their own GUI and password structure.

S330-005.01 Windows authentication (LDAP)This option for the psm2200 basic licence enables login to the psm2200 client using the user names and passwords defined for the Windows network.

S330-008.01 VM Virtual machineThis option for the psm2200 basic licence enables the operation of psm2200 in a virtual environment. VMware can be deployed as the virtualisation system. Note: Set VM to static IP addresses, otherwise relicensing will be required from the manufacturer.

Options


Drivers / Interfaces

Access controlS320-004.01 Interface to prime WebAccess

primion Access Control Management System Enables the operation of the prime WebAccess software in conjunction with psm2200. Datapoint generation is done automatically.Note: In order to operate with prime WebAccess, the TopView interface and the “Automatic datapoint generation” option have to be activated in prime WebSystems. Communication is done over Ethernet. You can order the datapoint packages under the part numbers S310-001.02 and S310-002.02 as required.

S320-011.01 Interface to XCess access control (GET) primion GET Access Control Management SystemEnables the operation of XCess in conjunction with psm2200. Datapoint generation is done automatically. Communication is done over Ethernet. You can order the datapoint packages under the part numbers S310-001.02 and S310-002.02 as required.

S320-031.01 Interface to Evalos-Secure.NET (DIGITEK) primion Digitek Access Control Management SystemEnables the operation of the prime Evalos-Secure.NET in conjunction with psm2200. Datapoint generation is done automatically. Communication is done over Ethernet. You can order the datapoint packages under the part numbers S310-001.02 and S310-002.02 as required.

Video – CCTVS320-041.01 ONVIF interface (Client) Profile S (driver / plugin)

The connection makes an ONVIF client available, in order to integrate ONVIF-compatible cameras in psm2200 and to communicate bi-directionally with them. Communication is done over Ethernet. The driver can be deployed in the psm2200 VdS 3534 option, S330-009.01.General planning advice: Before selecting the camera(s) you wish to deploy, please refer to the camera datasheet to ensure that the required ONVIF functionalities are available. Note: Please be aware that there are potential inconsistencies in respect of the scope of the ONVIF commands, on the part of the camera manufacturers. Any licences required for the operation of the video system must be taken into account and ordered as necessary.You can order the datapoint packages under the part numbers S310-001.02 and S310-002.02 as required. Driver functionality: Bidirectional communication with the cameras (control functions, state changes, etc.). Note: The datapoint packages, part numbers S310-001.02 and S310-002.02, must be ordered as required, in addition to the driver licence. Plugin functionality: Live stream display, archive search, PTZ functionality if supported by the camera. Please refer to the video system manufacturer’s camera compatibility reference list.


S320-026.01 Interface to HeiTel (Xtralis) (Driver/Plugin)Enables the connection of the HeiTel CCTV systems “CamTel, CamServer, CamDisc, CamMobile, ipVG” to psm2200. Datapoint generation is done automatically. Communication is done over Ethernet.Important planning information: The CCTV system “Heitel” is a discontinued line. It should not be used for new projects. General planning advice: Before selecting the cameras you wish to deploy, please refer to the video system manufacturer’s camera compatibility reference list. Any licences required for the operation of the video system must be taken into account and ordered as necessary.Driver functionality: Bidirectional communication with the video system. (peripherals, control functions, state changes, etc.). Note 1: The datapoint packages, part numbers S310-001.02 and S310-002.02, must be ordered as required, in addition to the driver licence. Note 2: The HeiTel Cam-Control server licence (dongle) must be ordered separately for the operation of the driver functionality.Plugin functionality: Live stream display, archive search, PTZ functionality if supported by the camera. Please refer to the video system manufacturer’s camera compatibility reference list. Note: No Cam-Control server licence is needed for operation of the plugin.

S320-038.01 Interface to Geutebrück GCore / GScope (Driver/Plugin)This driver enables the connection of the Geutebrück “GScore / GScope” CCTV system to psm2200. Datapoint generation is done automatically. Communication is done over Ethernet. General planning advice: Before selecting the cameras you wish to deploy, please refer to the video system manufacturer’s camera compatibility reference list. Any licences required for the operation of the video system must be taken into account and ordered as necessary.Driver functionality: Bidirectional communication with the video system. (peripherals, control functions, state changes, etc.). Note: The datapoint packages, part numbers S310-001.02 and S310-002.02, must be ordered as required, in addition to the driver licence.Plugin functionality: Live stream display, archive search, PTZ functionality if supported by the camera. Please refer to the video system manufacturer’s camera compatibility reference list.

S320-007.01 Interface to Geutebrück Reporter / Geviscope (Driver/Plugin)This driver enables the connection of the Geutebrück “Reporter / Geviscope” CCTV system to psm2200. Datapoint generation is done automatically. Communication is done over Ethernet. Important planning information: The CCTV system “Geutebrück GCore / GScope” is a discontinued line. It should not be used for new projects. General planning advice: Before selecting the cameras you wish to deploy, please refer to the video system manufacturer’s camera compatibility reference list. Any licences required for the operation of the video system must be taken into account and ordered as necessary.Driver functionality: Bidirectional communication with the video system (peripherals, control functions, state changes, etc.). Note: The datapoint packages, part numbers S310-001.02 and S310-002.02, must be ordered as required, in addition to the driver licence.Plugin functionality: Live stream display, archive search, PTZ functionality if supported by the camera. Please refer to the video system manufacturer’s camera compatibility reference list.




S320-012.01 Interface to Quadrox (Driver/Plugin)Enables the connection of the Quadrox CCTV system to psm2200. Datapoint generation is done automatically. Communication is done over Ethernet. Pre-requirement: Microsoft .NET Framework 4.0Important planning information: The production of the CCTV system “Quadrox” is discontinued. It should not be used for new projects. General planning advice: Before selecting the cameras you wish to deploy, please refer to the video system manufacturer’s camera compatibility reference list. Any licences required for the operation of the video system must be taken into account and ordered as necessary. Note: We recommend that the video recording system should be installed and operated on a separate computer, in order to optimise performance.Driver functionality: Bidirectional communication with the video system. (peripherals, control functions, state changes, etc.).Note: The datapoint packages, part numbers S310-001.02 and S310-002.02, must be ordered as required, in addition to the driver licence.Plugin functionality: Live stream display, archive search, PTZ functionality if supported by the camera. Please refer to the video system manufacturer’s camera compatibility reference list.

S320-008.01 Interface to Milestone (Driver/Plugin)Enables the connection of the Milestone CCTV XProtect professional, XProtect Enterprise, XProtect Expert and XProtect Corporate systems to psm2200. Datapoint generation is done automatically. Communication is done over Ethernet. General planning advice: Before selecting the cameras you wish to deploy, please refer to the video system manufacturer’s camera compatibility reference list. Any licences required for the operation of the video system must be taken into account and ordered as necessary. Note: We recommend that the video recording system should be installed and operated on a separate computer, in order to optimise performance.Driver functionality: Bidirectional communication with the video system. (peripherals, control functions, state changes, etc.). Note: The datapoint packages, part numbers S310-001.02 and S310-002.02, must be ordered as required, in addition to the driver licence. Plugin functionality: Live stream display, archive search, PTZ functionality if supported by the camera. Please refer to the video system manufacturer’s camera compatibility reference list.


S320-022.01 Interface to Funkwerk-Plettac (POSA) (Driver/Plugin)Enables the connection of the Funkwerk-Plettac CCTV POSA system to psm2200. The import and generation of the datapoints from the CCTV system is done using an import tool in the psm2200 Configuration module. Communication is done over Ethernet. Project-specific approval for the deployment of the driver must be obtained from the Funkwerk company.Important planning information: The CCTV system “POSA Funkwerk Plettac” is a discontinued line. It should not be used for new projects. General planning advice: Before selecting the cameras you wish to deploy, please refer to the video system manufacturer’s camera compatibility reference list. Any licences required for the operation of the video system must be taken into account and ordered as necessary.Note: We recommend that the video recording system should be installed and operated on a separate computer, in order to optimise performance. Driver functionality: Bidirectional communication with the video system (peripherals, control functions, state changes, etc.). Note: The datapoint packages, part numbers S310-001.02 and S310-002.02, must be ordered as required, in addition to the driver licence. Plugin functionality: Live stream display, archive search, PTZ functionality if supported by the camera. Please refer to the video system manufacturer’s camera compatibility reference list.

S320-029.01 Interface to Axis (IP camera viewer) This driver enables the integration of Axis IP cameras in psm2200 using a plug-in.

S320-023.01 Interface to Mobotix (IP camera viewer) (Driver/Plugin)Enables the integration of Mobotix IP cameras in psm2200. The import and generation of the datapoints from the CCTV system in the psm2200 server is automatic, if supported by the camera protocol. Communication is done over Ethernet.General planning advice: Before selecting the cameras you wish to deploy, please refer to the video system manufacturer’s camera compatibility reference list. Any licences required for the operation of the video system must be taken into account and ordered as necessary.Note: We recommend that the video recording system should be installed and operated on a separate computer, in order to optimise performance.Driver functionality: Bidirectional communication with the video system (peripherals, control functions, state changes, etc.). Note: The datapoint packages, part numbers S310-001.02 and S310-002.02, must be ordered as required, in addition to the driver licence.Plugin functionality: Live stream display, archive search, PTZ functionality if supported by the camera. Please refer to the video system manufacturer’s camera compatibility reference list.




Intrusion detection systemsS320-010.01 psm2200 Honeywell EMT; MB Secure Interface

Enables the connection of intruder alarm panels from the MB-Secure range to psm2200. Communication is done over Ethernet. You can order the data point packages under the part numbers S310-001.02 and S310-002.02 as required. Note: The driver can be deployed from psm2200 Version 3.1.0.0.

S320-001.01 Interface to Honeywell/Novar EMT; MB/HB Series in the IGIS LoopImportant planning information: The production of the EMT system “Honeywell / Novar MB / HB-Serie im IGIS-Loop” is discontinued. It should not be used for new projects. Enables the connection to psm2200 of IDS panels from the MB/HB Series that are operated in the IGIS Loop network. The import and generation of the datapoints from the IDS system is done using an import tool in the psm2200 Configuration module. Communication is done over a monitored serial RS232 interface. You can order the datapoint packages under the part numbers S310-001.02 and S310-002.02 as required. Note: The IGIS LOOP Controller Interface is required for operation. The following types are supported: MB / HB 48, MB / HB 100, MB 256plus (Option: Upgrade the MB 256 to MB 256 plus with an upgrade kit).

S320-003.01 Interface to Esser EMT 5008 (Honeywell)Important planning information: The production of the EMT system “Honeywell Esser EMT 5008” is discontinued. It should not be used for new projects. Enables the connection to psm2200 of Esser/EMA 5008 IDS panels via essernet®.The import and generation of the datapoints from the IDS system is done using an import tool in the psm2200 Configuration module. Communication is done over a monitored serial RS232 interface. You can order the datapoint packages under the part numbers S310-001.02 and S310-002.02 as required.Note: The serial essernet® interface with micro-module (Esser part number 784856) is required for operation.

S320-014.01 Interface to Galaxy Dimension EMT GD 520 (Honeywell)Enables the connection to psm2200 of Galaxy Dimension IDS panels. Datapoint generation is done automatically. Communication is done over Ethernet. The following types are supported: GD 520, GD-264, GD-96, GD-48, G-512 (older version), G3-512, G3-48, G3-144 You can order the datapoint packages under the part numbers S310-001.02 and S310-002.02 as required.

S320-018.01 Interface to Telenot EMT Complex 400HEnables the connection to psm2200 of Complex 400H IDS panels. Datapoint generation is done automatically. Communication is done over a monitored serial RS232 interface. You can order the datapoint packages under the part numbers S310-001.02 and S310-002.02 as required.


Fire detection systemsS320-002.01 Interface to Esser BMT (Honeywell)

Enables the connection to psm2200 of Esser fire alarm panels via essernet®. The import and generation of the datapoints from the IDS system is done using an import tool in the psm2200 Configuration module. Communication is done over a monitored serial RS232 interface. You can order the datapoint packages under the part numbers S310-001.02 and S310-002.02 as required.Note: The serial essernet® interface with micro-module (Esser part number 784856) is required for operation. The following Esser fire alarm panels are supported: Esser FlexES, IQ8C/M; BMA Series 8000x The following Honeywell Novar central units are supported: BMC 1024-F in essernet® via serial essernet® interface; 1 upgrade kit with the Esser part number 78931 is needed for each BMC 1024-F . BMC 1024-F firmware pre-requirement: Workstation V7.04, main computer V7.08, eSEI with K Bus interface connection V1.0.0R000

S320-036.01 Interface to Hekatron Integral IP BMT Note for operators: Before project planning / operation on psm2200, please clarify possible license fees with the corresponding hardware manufacturer.Enables the connection to psm2200 of Hekatron Integral IP fire alarm panels via ISP protocol®. (Operation of Securiton SecuriFire BMT via ISP protocol on request)Integration level 1: There is the option of creating a logical sub-fire panel that can be made up of a maximum of 16 physical single panels.Integration level 2: Enables the integration of the Hekatron N3 Seconet ®.The import and generation of the datapoints from the IDS system is done using an import tool in the psm2200 Configuration module. Communication is done over Ethernet. You can order the datapoint packages under the part numbers S310-001.02 and S310-002.02 as required.Supported Hekatron panels: Integral IP MX, Integral IP BX, Integral IP CX.

S320-037.01 Interface to SICLI BMT Important planning information: The Interface to “SICLI BMT” is a discontinued line from 12/2019. It should not be used for new projects. Enables the connection to psm2200 of SICLI COP 3000 fire alarm panels.The import and generation of the datapoints from the IDS system is done using an import tool in the psm2200 Configuration module. Communication is done over a monitored serial RS232 interface. You can order the datapoint packages under the part numbers S310-001.02 and S310-002.02 as required.

Call systemsS320-015.01 Interface to Clino Systevo – IPC Nurse Call system

Enables the connection of Ackermann Call Systems to psm2200 through an IPC module. Communication is done over Ethernet. The following types are supported: Clino 99plus and Clino Systevo via IPC module. You can order the datapoint packages under the part numbers S310-001.02 and S310-002.02 as required.




Voice alarm systemsS320-043.01 SIP Client Interface

The psm2200 SIP Client communicates using Session Initiation Protocol (SIP) and makes it possible to send voice messages to a SIP telephony user. The voice messages are generated as strings and can be acknowledged using a defined DTMF Acknowledgement code and can also be documented in psm2200. The text-to-speech synthesis is done using Balabolka, which is included in the scope of delivery of the driver.Note: The driver can be deployed from psm2200 Version 3.1.0.0 and from Windows 7 (64 bit). The possible range of languages available for speech synthesis is dependent on the deployed operating system. From Windows 8, TextToSpeech is integrated in the operating system and the complete language package has to be installed for each usable language, in online or offline mode.Currently, only German and English are supported from Windows 10 and Windows Server 2016.You can order the data point packages under the part numbers S310-001.02 and S310-002.02 as required.

S320-016.01 Interface to SAA VARIODYN® D1 Voice Alarm System (Honeywell)This driver enables the connection to psm2200 of Esser SAA VARIODYN® D1 Voice Alarm System (Honeywell). Datapoint generation is done automatically. Communication is done over Ethernet. You can order the datapoint packages under the part numbers S310-001.02 and S310-002.02 as required.Note: The driver needs a free port at the VARIODYN® D1 Digital output module (DOM).

Intercom systemsS320-020.01 Interface to TDM-NIS Emergency call system

Enables the connection of TDM (Trans Data Management AG) Emergency call and Information systems (NIS) to psm2200.The scope of function includes the connection control of the telephone and operating devices and the display of their operational status. Communication via Ethernet over the CTI (CSTA) and SNMP interfaces.You can order the datapoint packages under the part numbers S310-001.02 and S310-002.02 as required.

S320-019.01 Interface to AVAYA IMS message serverEnables the connection of the Avaya message server to psm2200, via Alpha protocol. Communication via serial interface.You can order the datapoint packages under the part numbers S310-001.02 and S310-002.02 as required.

S320-021.01 Interface to ESPA 4.4.4 – Terminal devicesEnables the connection of the ESPA 4.4.4 protocol for the distribution of messages to mobile terminal devices such as DECT pagers.Communication via Ethernet TCP/IP or serial interface. You can order the datapoint packages under the part numbers S310-001.02 and S310-002.02 as required.

S320-027.01 Interface to Siedle – ACCESS; IP InterfaceEnables the connection of the Siedle IP systems to psm2200.Datapoint generation in psm2200 is done automatically with the Siedle Driver Version SDK v 1.0.0.1. Communication is done over Ethernet.You can order the datapoint packages under the part numbers S310-001.02 and S310-002.02 as required.


CommunicationS320-013.01 Interface to Bosch-Connetix gateway

Enables the connection of the Bosch Connetix Gateway DS6100i to psm2200. The import and generation of datapoints in psm2200 is done automatically. Communication via UDP/IP Ethernet or serial RS232 interface. You can order the datapoint packages under the part numbers S310-001.02 and S310-002.02 as required.

S320-044.01 ATS IDS4100 InterfaceThe driver enables the connection of the IDS4100 (software based server), Alarm receiver unit from ATS to psm2200. The IDS4100 accepts alarms and technical messages in the VdS 2465 protocol that have been sent using the TCP/IP and GSM(GPRS) communication paths. Using transmission units such as the comXline 3516 (Telenot) or DS7700 (Honeywell), these are transmitted to the IDS4100 receiver unit and made available for further processing in psm2200 as data points.The communication between psm2200 and the IDS 4100 is done using TCP/IP (S4 protocol, in acc, VdS2465). The ATS IDS4100 connection (VdS recognition G109810) can be deployed together with the psm2200 VdS3534 option (S330-009.01) and in this way, it allows a system for operation within Monitoring and Alarm Receiving Centres in acc. EN 50518-2 to be established. Note: The driver can be deployed from psm2200 Version 3.1.0.0.You can order the data point packages under the part numbers S310-001.02 and S310-002.02 as required.

S320-042.01 Interface to Telenot comXline AE Important planning information: Production of the Telenot comXlineAE Receiver unit has been stopped and it is therefore now a discontinued item. It should not be used for new projects. The IDS4100 from the ATS Company (software based server) can be used to replace it. To do this, you will need to deploy the S320-044.01 “Interface to ATS IDS4100”. The driver enables the connection of the Telenot comXline AE receiver unit. The alarm receiver unit is used to accept alarm messages such as intrusion, fire, arming/disarming, etc. together with technical messages such as operational statuses, threshold values, faults, etc. Using transmission units such as the comXline 3516, these are transmitted to the comXline AE receiver unit and made available in psm2200 as data points. The generation of data points in psm2200 is done automatically, based on a message from the corresponding data point. Communication is done over the serial interface. The driver can be deployed in the VdS 3534 option, S330-009.01. You can order the datapoint packages under the part numbers S310-001.02 and S310-002.02 as required.

S320-040.01 Interface to SNMP Client / Version 1 and Version 2The connection makes an SNMP client available, in order to accept data from SNMP-enabled devices into psm2200. If supported by the device, the possible values / states can be queried and set. This enables a basic monitoring function at the same time. Communication is done over Ethernet. Note:Supported protocols: SNMP V1, SNMP V2c (further protocols on request)You can order the datapoint packages under the part numbers S310-001.02 and S310-002.02 as required.




Building management systemsS320-039.01 OPC Client Interface (UA)

The OPC Client (UA protocol) connection makes an OPC (UA protocol) client available, in order to integrate and control data from external OPC-UA server systems in psm2200. Communication is done over Ethernet. You can order the datapoint packages under the part numbers S310-001.02 and S310-002.02 as required.

S321-002.01 OPC Client Interface (DCOM)The connection makes an OPC client available, in order to accept data from external systems/applications in psm2200. The following protocols are supported: Alarm Event 1.10, Data access 1.0a / Data access 2.05 / Data access 3.0 Communication is done over Ethernet. You can order the datapoint packages under the part numbers S310-001.02 and S310-002.02 as required.

S321-001.01 OPC Server Interface (DCOM)The connection makes an OPC server available, in order to transfer data from psm2200 to external systems/applications. The following protocols are supported: Alarm Event 1.10, Data access 1.0a / Data access 2.05 / Data access 3.0 Communication is done over Ethernet. You can order the datapoint packages under the part numbers S310-001.02 and S310-002.02 as required.Note: The number of datapoints is calculated from the number of datapoints that have to be provided at the external system and must be taken into account when placing the order.

S321-003.01 BACnet Client interfaceThe connection makes a BACnet client available, in order to accept data from external BACnet devices within a closed IP network into psm2200 and to communicate bidirectionally with the devices.The protocol that is supported for data transfer is BACnet IP. Datapoint transfer is done through the integrated BACnet browser.You can order the datapoint packages under the part numbers S310-001.02 and S310-002.02 as required.Planning information 1:Before deploying the driver, it has to be clarified which BACnet objects and commands in psm2200 are to be implemented. Please check the corresponding data in the BACnet driver documentation supplied with psm2200.It also has to be clarified whether BACnet compliance (ANSI/ASHRAE BACnet Standard 135-2008; alternatively DIN EN ISO 16484-5) is given with the hardware that is to be connected.This driver does not cover all the BACnet objects and commands that are theoretically possible.Planning information 2:If there is a requirement to integrate devices outside the closed network system, a VPN tunnel has to be installed using a BBMD (BACnet/IP Broadcast Management Device) router. All BACnet devices throughout the complete network have to have BBMD functionality.One possible BACnet router that could be used is the UBR-O1 from the MBS company. Order details and technical information can be found under: www.mbs-software.de/en/

S320-032.01 Interface to Modbus IP Client / Serial MasterThe connection makes a Modbus client available, in order to accept data from external systems/applications in psm2200.The protocol that is supported for data transfer is Modbus IP and serial (RS232 / RS485) over Modbus-Serial-Master. You can order the datapoint packages under the part numbers S310-001.02 and S310-002.02 as required.


Escape route technologyS320-028.01 Interface to Assa Abloy ERT Bus controller TSBC 970-20

Enables the connection of the effeff TSBC 970-20 Bus controller to psm2200.The import and generation of datapoints in psm2200 is done automatically.Communication is done over Ethernet.The driver can be deployed in the psm2200 VdS 3534 option, S330-009.01.You can order the datapoint packages under the part numbers S310-001.02 and S310-002.02 as required.

S320-006.01 Interface to Assa Abloy ERT Bus controller 925Important planning information: The production of the ERT system “ERT Bus controller 925” is discontinued. It should not be used for new projects. Enables the connection of the effeff BCM 925 Bus controller to psm2200.The import and generation of datapoints in psm2200 is done automatically.Communication is done over a monitored serial RS232 interface. You can order the datapoint packages under the part numbers S310-001.02 and S310-002.02 as required.

Third-party systemsS320-030.01 Interface to Third-Party Systems

Enables the connection of third-party systems in conjunction with psm2200.The import and generation of datapoints in psm2200 is done automatically, depending on the driver protocol.The driver supports third-party systems whose protocol can be connected to, through a customised programming of the interface SDK. The customised programming is not a component of the driver and and a separate offer has to be made for the work involved, which will be dependent on the complexity of the interface functionality.You can order the datapoint packages under the part numbers S310-001.02 and S310-002.02 as required. Note: Alternatively, the development can be done by primion Technology GmbH. In this case, S321-005.01, Development of a customised interface, has to be ordered separately.

OtherS321-004.01 External database display

Visualisation GUI for the display of information from external databases. The database query is done using Groovy scripts. The driver supports the following databases: Oracle 10, 11, 12, 18 and 19 (including express versions)MSSQL 2005, 2008, 2012, 2014, 2016, 2017, 2019 (including express versions)MySQL from version 5.1Note: One datapoint corresponds to one table from the external database that is being accessed.

S321-006.01 NTP Network Time Protocol The driver enables the monitoring of the time synchronisation between psm2200 and Windows operating systems. If a deviation is detected, a corresponding error message is generated that can be used for further evaluations/controls.

S321-007.01 psm2200 Universal V24 Read-only monitor connectionThe driver can receive the data that is sent to psm2200 over the serial V24 interface and can make it available for further evaluation Note: The driver can be deployed from psm2200 Version 3.1.0.0.You can order the data point packages under the part numbers S310-001.02 and S310-002.02 as required.



Service

psm2200 – Customised driver developmentS321-005.01 Development of customised interfaces

Development of an “interface/connection” to a third-party system, if a specification and description of the interface is provided.Pre-requirements: Provision of a functioning device environment (hardware & software).Requirements specification and an SDK for the execution of the development work.Note: Please take any licence costs and legal restrictions imposed by the third-party supplier into account.

G003-100.03 Creation of Functional specification and Project management (day rate)Covers the analysis of the system environment that is to be integrated in pm2200 and the resultant creation of the Requirements Specification and the Functional Specification. This part number refers to the day rate for the work involved and is calculated on a T&E basis.

ServicesG003-100.03 Creation of Functional specification and Project management (day rate)

Covers the analysis of the system environment that is to be integrated in pm2200 and the resultant creation of the Requirements Specification and the Functional Specification. This part number refers to the day rate for the work involved and is calculated on a T&E basis.

G003-101.03 Installation, customising, commissioning, training (day rate)Software installation, adaptation to customer specification in terms of Workflows, Scripts, etc., commissioning, documentation and training required for a psm2200 system, carried out by a system engineer. This part number refers to the day rate for the work involved and is calculated on a T&E basis. Pre-requirement: Provision of a functioning device environment (hardware & software) and the Requirements specification.

G003-102.01 Generation of a multi-functional datapoint (up to1,000 datapoints)Generation of multi-functional datapoint. Pre-requirement: Provision of a functioning device environment (hardware & software) and the Requirements specification.

G003-103.01 Generation of a multi-functional datapoint (from 1,001 datapoints)Generation of multi-functional datapoint.Pre-requirement: Provision of a functioning device environment (hardware & software) and the Requirements specification.

G003-104.01 Generation of a Message TextGeneration of message texts including text describing the measures that are to be taken.Pre-requirement: Provision of the Requirements specification.

G003-105.01 Import of a multi-functional building plan graphicImport of an existing graphic page, e.g. building plan into psm2200.Pre-requirement: Provision of the Requirements specification and corresponding building plan graphicsImportable formats: emf, wmf, svg, jpeg, jpg, gif, png, bmp. Other file formats must be converted into one of these formats.

primion Technology GmbHSteinbeisstr. 2-5 72510 Stetten a. k. M. +49 7573 9520 [email protected] www.primion.de

OPERTIS GmbH Auf dem Hagen 1 34454 Bad Arolsen +49 5691 877410 [email protected] www.opertis.de

sa GET nvAntwerpsesteenweg 107 2390 Malle +32 3 312 92 30 [email protected] www.get.be

GET Nederland bv Albert Einsteinweg 4 8218 NH Lelystad +31 320 25 37 90 [email protected] www.get.nl

primion Digitek SLUCalle Teide, 3, Oficina 0.3. 28700 San Sebastian de los Reyes (Madrid) +34 93 4774 770 [email protected] www.primion-digitek.es

primion S.A.S.205 av. Georges Clemenceau 92000 Nanterre +33 1 41 10 43 70 [email protected] www.primion.fr

Time & Security Division

Germany

Belgium

The Netherlands

Spain

France

Germany

04/2

0P

061-

035.

10

psm2200 Ordering Information - Primion

Documents

Transcript of psm2200 Ordering Information - Primion