Programmable Logic Control (PLC) Solutions Guide

Programmable Logic Control (PLC) Solutions Guide

Industrial Automation Solutions

www.ti.com/automation 2015

http://www.ti.com/automation

The programmable logic controller is the workhorse of industrial control systems. It uses digital and analog I/O modules to interface to sensors, actuators and other equipment. These I/O modules must meet stringent electrical specifications and designers face challenges in conditioning and converting these signals. In addition, increasing levels of embedded processing and connectivity can be seen on these modules.

The PLC systemPLCs can be segmented by I/O count and scan rates. They can also be classified as brick type versus modular PLCs. A small or brick PLC has a fixed number of connections for inputs and outputs. Modular PLCs have a chassis (also called a rack) into which are placed modules with different functions. The processor and selection of I/O modules is customized to fit the application. A modular PLC consists of the central processing unit (CPU), a power supply and various I/O modules. The CPU performs the main controller functions like scanning data and running control sequences. The power supply unit converts line power to 24 volts. The I/O modules are used to measure data from sensors and to control various actuators. Together, the

input and output modules along with the central controller form a control loop.

I/O module typesI/O modules can be classified as analog input (AI), analog output (AO), digital input (DI) and digital output (DO). They are usually cate go rized into 2, 4, 8 and 16channel modules. I/O modules need to meet stringent electrical specifications such as the IEC 610004 family of electro magnetic compatibility (EMC) tests for surge, ESD (electro static discharge) and EFT (electrically fast transients). They also need shortcircuit and over load protection. All these modules include isolation between the control side and the field side via DCDC converters and isolation on the digital commu nication side between the field devices and the digital backplane. Communication over the digital backplane is done by a variety of interfaces (RS485, CAN, Ethernet, LVDS, etc.) In distributed control systems or between equipment, industrial fieldbuses (PROFIBUS®, DeviceNet™, CANopen®, Modbus®, EtherCAT®, EtherNet I/P™, PROFINET®, SERCOS®, POWERLINK, etc.) are used for communication. On the following pages we discuss solutions from TI for these various I/O types.

110V /220V

Programmable Logic Controller with local IO(DIN-rail in cabinet)

Remote IO(DIN-rail)

Decentralized IO(machine attached)

CPU

Coms

SpecialFunction

BusCoupler

SpecialFunction

BusCoupler

Power

Slave

Slave

Master

Slave

Std Ethernet

Industrial Ethernet

BusCoupler

Pow

er

Back

pla

ne B

us

Inpu

t

Pow

er

In-/

Out

put

Back

pla

ne B

us

Pow

er

Inpu

t

Pow

er

In-/

Out

put

In-/

Out

put

Pow

er

Inpu

t

Table of contents

Programmable logic control2 Overview

Analog input3 TI Designs4 Amplifiers5 Precision ADCs (≤ 10 MSPS)5 Programmable gain amplifiers 6 Digital isolators6 Voltage reference

Analog output6 Overview6 TI Designs7 Precision DACs7 Analog output driver

Digital input8 TI Designs8 Digital serializer

Digital output8 TI Designs9 Drivers

Connectivity & interface for I/O module9 Microcontrollers10 Industrial interface transceiver10 LVDS devices10 Logic: LVC

Power for I/O module11 TI Designs12 Input power protection12 LDO linear regulator12 DCDC regulator13 Window comparator

Communication module and PLC controller13 Microprocessors13 Industrial ethernet protocols15 Industrial protocol support15 Ethernet PHY15 eFuses16 DCDC regulators16 DDR termination regulators16 Power Management ICs (PMICs)16 Load switches17 Clock generators17 Clock fanout buffers

2 | Programmable Logic Control (PLC) Solutions Guide 2015 Texas Instruments

Programmable Logic Control (PLC)Overview

Texas Instruments analog input solutions address a wide range of analog input modules in the factory and process automation industry, including temperature (thermocouple and RTD), 420 mA and single ended or differential 05 V, 010 V, ±5 V and ±10 V. The TI Designs provide insights in how to handle multiple channels per module, DeltaSigma and SAR ADC based

signal acquisition and universal input stages. Industry 4.0 (Industrie 4.0) requirements for diagnostics and HART are also showcased. Small footprint and high efficiency isolated power supplies for generating positive and negative voltages help meet the demands for more channels per module and smaller form factors.

Group Isolated Analog Input Module

Per Channel Isolated Analog Input Module

AMP

Protection

Protection±5 V, ±10 V

0–5 V, 0–10 V

4–20 mA0–10 mA

From Sensors

Group Isolated Analog Input Module

DigitalIsolation

DigitalIsolation

Controller Interface

Memory

Buffer

HART

ADC

VREF

PGAMUX

Buffer

Protection

Protection

AMP


MemoryDigital

Isolation

DigitalIsolation

ADC

ADC

±5 V, ±10 V0–5 V, 0–10 V

4–20 mA0–10 mA

Field Inputs From Sensors

DigitalIsolation

DigitalIsolation


PGA

AMP

ADCMUX

Protection

Protection VREF

V+

Temp

Flow

Optical

Pressure

Level

+

LEGEND Logic

ADC/DACClocksOther

Power

RF/IF

ProcessorInterface

Amplifier

TI DesignsName Description Key Features

12-Bit, 8 channel, integrated analog input module for programmable logic controllers (PLC)

TIDA-00119 is a complete, highly-integrated PLC analog input module front-end reference design that is designed and tested to meet IEC61000-4 standards for industrial automation systems. The design can be configured for 4 differential inputs or 8 single-ended inputs with 12-bit ADC resolution and a sample rate of up to 1 MSPS. These inputs can also be programmed to take current or voltage inputs with selectable ranges. The design also includes an isolated power supply providing all necessary module voltages, input surge and ESD protection and an isolated digital data interface that can be connected to any microcontroller, FPGA or ASIC via SPI interface. Full documentation, test results, design files and necessary firmware are available to help reduce time to market.

• Designed to comply with IEC61000-4 standards for ESD, EFT and Surge• Up to 8 channels user programmable inputs and configurable over-range

capability of 20%• Four voltage inputs: 3 Single ended & 1Differential with impedance > 1 M ±10

V, ±5 V, ±2.5 V, 0-10 V, 0- 5 V, Up to ±12 V with external reference• Four current inputs: 0-20 mA, 4-20 mA (with input impedance of 250 Ω)• Accuracy over entire input range• Voltage: < ±0.2% full scale at 25°C• Current: < ±0.35% full scale at 25°C• On-board isolated FlybuckTM power supply with inrush current protection

16-Bit, 8 channel, integrated analog input module for programmable logic controllers (PLC)

The TIDA-00164 reference design provides a complete solution for a single supply industrial control analog input module. The reference design is suitable for process control end equipment like programmable logic controllers (PLC), distributed control system (DCS), data acquisition systems (DAS) modules that must digitize standard industrial current inputs and bipolar or unipolar input voltage ranges up to ±10 V.

• 8-channel, 16-bit SAR ADC ADS8688 that supports from 300 ksps to 30 ksps per channel

• Programmable channels: each channel can be configured as current or voltage input with software configuration

• Programmable current range (0-20mA) and voltage range (±10 V)• Single 24 V input power supply operation• Designed for IEC-61000 compliance (IEC-61000-4-4: EFT up to ±2 kV @ 5 kHz

on signal ports; IEC-61000-4-2: ESD up to 4 kV contact & 8 kV air discharge; IEC-61000-4-5: surge up to ±1 KV line-earth (CM) on signal ports)

16-Bit analog mixed input and output module for programmable logic controller (PLC) reference design

The TIDA-00170 is a reference design for industrial control analog mixed input output modules. The design implements four channel analog input & two channel analog output. The analog input channels can measure all standard industrial voltages up to ±10 V and current inputs up to 24 mA. The two simultaneous analog outputs can source voltage up to ±10 V and current up to 24 mA. The reference design includes the necessary on-board protection circuit & is tested for IEC61000-4 standard – EFT, ESD and surge requirements with IO Controller platform. The protection circuitry does not negatively affect the design and test results showed typical unadjusted errors were less than 0.1% of the full-scale range (FSR) for the analog input channel and less than 0.2% FSR for the analog output channel.

• 16-bit resolution, user programmable analog input output ranges• Programmable channels: each I/P channel can be configured as current or

voltage input and O/P channel can be configured as voltage or current output with software configuration

• Accuracy–input Ch better than ±0.1% FSR at 25°C, output Ch better than ±0.2% FSR at 25°C

• On-board isolated Flybuck power supply with inrush current protection• Designed to comply with IEC61000-4 standards for ESD, EFT, and surge

Temperature sensor interface module for programmable logic controllers (PLC)

The TIDA-00018 reference design enables faster development of high precision temperature measurement solutions using 24-bit delta-sigma ADC and most widely used temperature sensors like thermocouple and RTD. The design guide will address the sensor signal conditioning, thermocouple cold junction compensation, ratiometric measurement technique for RTD, recommended software flow, sensor linearization, sensor diagnostics, transient protection, PCB layout and other practical design considerations for achieving high precision robust design for temperature measurement in industrial applications. The temperature sensor interface module is a fully isolated design, which is essential for small sensor signal measurement. The heart of this reference design is a 24-bit delta-sigma ADC that provides a high resolution, high–integration, low-noise, and low-cost complete sensor analog front-end (AFE) for DC sensing applications. This ADC also makes it suitable to interface with different types of sensors, thus saving board space, reducing design efforts, decreasing the time to market, and lowering BOM cost. Furthermore, external protection circuitry has been successfully tested for compliance with regulatory IEC61000-4 EFT, ESD, and surge standards. Compliance to IEC61000-4 is necessary to ensure that the design not only survives but also perform as intended in the harsh/noisy industrial environment.

• Two different sensor input channels: K-type thermocouple input with CJC• Compatible to 2-, 3- or 4-wire RTD probes• Ratiometric measurement for RTD• Overall measurement accuracy better than: For thermocouple: ±1°C, for RTD:

±0.4°C• Sensor wire open circuit or signal out-of-range detection• Comply to IEC-61000-4 requirements: IEC-61000-4-4: EFT up to ±1 kV @ 5 kHz

on signal ports• IEC-61000-4-2: ESD up to 4 kV contact & 8 kV air discharge• IEC-61000-4-5: Surge up to ±1 kV line-earth (CM) on signal ports

Texas Instruments Programmable Logic Control (PLC) Solutions Guide 2015 | 3

Analog inputsTI Designs

http://www.ti.com/tool/TIDA-00119




Amplifiers

Device DescriptionNumber of Channels

Total Supply Voltage (Min)

(+5 V=5,±5 V=10)

Total Supply Voltage (Max)

(+5 V=5, ±5 V=10)

VOS (Offset Voltage @

25°C) (Max) (mV)

Offset Drift (Typ)

(µV/°C)

Slew Rate (Typ) (V/µs)

BW @ Acl (MHz)

GBW (Typ) (MHz)

Iq per Channel

(Max) (mA)

Vn @ 1 kHz (typ)

(nV/√Hz)

Operating Temp. Range

(°C)Pin/

PackagePrice * (US$)

High speed amplifiers

THS4531A Ultra low power, RRO, fully-differential amplifier 1 2.5 5.5 0.4 3 220 36 0.25 10 –40 to 125

10/QFN8/VSSOP8/SOIC

1.10

THS4532 Dual, ultra low power 0.25 mA, RRO, fully differential amplifier 2 2.5 5.5 0.4 3 220 36 0.25 10 –40 to 125 16/TSSOP 1.85

THS452x Very low power rail-to-rail output fully differential amplifier 1,2,4 2.5 5.5 2 2 490 145 1.14 4.6 –40 to 85

8/VSSOP, 8/SOIC

16/TSSOP, 38T/SSOP

1.21

THS4541 High-speed differential I/O amplifier 1 2.7 5.4 0.45 0.5 1500 620 10.1 2.2 –40 to 125 10/QFN16/QFN 2.65

OPAx835 Dual, ultra low power, rail-to-rail out, negative rail In, VFB amplifier 1,2 2.5 5.5 0.5 2.25 160 56 0.25 9.3 –40 to 125

6/SOT-23, 10/QFN

10/µQFN, 10/VSSOP

8/SOIC

1.35

OPAx836 Dual, very low power, rail-to-rail out, negative rail in, VFB op amp 1,2 2.5 5.5 0.4 1.1 560 205 1 4.6 –40 to 85

6/SOT-23, 10/QFN

10/µQFN, 10/VSSOP

8/SOIC

1.50

THS403x 100-MHz low noise voltage-feedback amplifier 1,2 9 32 2 2 100 200 8.5 1.6 –40 to 85, 0

to 708/MSOP8/SOIC

3.70 | 100u

THS4130 Fully differential input/output low noise amplifier with shutdown 1 5 30 2 4.5 52 150 12.3 1.3 –40 to 85, 0

to 70

8/MSOP8/VSSOP8/SOIC

5.91 | 100u

THS4281Very low-power high speed rail-to-rail input/output voltage feedback operational amplifier

1 2.7 16.5 2.5 7 35 95 0.8 12.5 –40 to 855/SOT-238/VSSOP8/SOIC

1.23

Precision amplifiers

OPA21880.03 µV/°C, 6 µV Vos, low-noise, rail-to-rail output, 36 V zero-drift operational amplifier

2 4 36 0.025 0.03 0.8 2 0.475 8.8 –40 to 105 8/SOIC, 8/VSSOP 1.05

OPA2111.1 nV/rtHz noise, low-power, precision operational amplifier in tiny DFN-8 package

1 4.5 36 0.05 0.15 27 45 4.5 1.1 –40 to 1258/SOIC, 8/SON,

8/VSSOP3.45

OPA14011 MHz, single-supply, low-noise, precision, rail-to-rail output, JFET amplifier

1 4.5 36 0.12 0.35 20 11 2 5.1 –40 to 1258/SOIC,

5/SOT-23, 8/VSSOP

1.55

OPA827 Low-noise, high-precision, JFET-input operational amplifier 1 4 36 0.15 2 28 22 5.2 4 –40 to 125 8/SOIC, 8/

VSSOP 3.75

OPAx227 High-precision, low-noise operational amplifiers 1,2,4 5 36 0.075 0.1 2.3 8 3.8 3 –40 to 85

DIP-8, SO-8, DIP-14, SO-14

1.402.074.53

OPA320 Precision, 20 MHz, 0.9 pA Ib, RRIO, CMOS operational amp 1 1.8 5.5 0.15 1.5 10 20 1.75 8.5 –40 to 125 5/SOT-23,

6/SOT-23 0.80

OPA365 2.2 V, 50 MHz, low-noise, single-supply rail-to-rail operational amplifier 1 2.2 5.5 0.2 1 25 50 5 4.5 –40 to 125 5/SOT-23,

8/SOIC 0.65

OPA335/ 2335

0.05 µV/°C max, single-supply CMOS operational amplifier 1,2 2.7 5.5 0.005 0.02 1.6 2 0.35 1.4 –40 to 125

5/SOT-23, 8/SOIC,

8/VSSOP

1.121.79

OPAx19236 V, Precision, rail-to-rail input/output, low offset voltage, low input bias current op amp with e-trim

1,2,4 4.5 36 0.025 0.15 20 10 1.2 5.5 –40 to 1255/SOT-23,

8/SOIC, 8/VSSO

1.352.162.75

OPAx172 36 V, single-supply, 10 MHz, rail-to-rail output operational amplifiers 1,2,4 4.5 36 1 0.3 10 10 1.8 7 –40 to 125

5/SC70,5/SOT-23,

8/SOIC, 8/VSSOP,14/SOIC,

14/TSSOP

0.650.991.49

*Suggested resale price in U.S. dollars in quantities of 1,000.


Analog inputsAmplifiers

http://www.ti.com/product/OPA140












http://www.ti.com/product/THS4031




http://www.ti.com/product/THS4531A



Precision ADCs (≤10 MSPS)

Device DescriptionResolution

(Bits)

Sample Rate (Max) (SPS)

No. of Input Channels

VREF (V)

INL (Max)

(±)

Power Consumption (Typ) (mW) Architecture

Input Voltage

Range (V) Interface

Operating Temperature Range (°C)

Pin/ Package

Price* (US$)

LMP90097/098/ 099/100

Multi-channel, low power 24-bit sensor AFE with true continuous background calibration

24 214 4/4/7/7 Int/ext 15 ppm 5.3 Delta-Sigma ±VREF/PGA Serial SPI –40 to 125 28/HTSSOP 3.43/3.61/3.80/4.00

ADS1246/7/8 Precision 24-bit ADCs with low-noise PGA for small signal sensors 24 2k 1/3/7 Int/ext 15 ppm 2.3 Delta-Sigma ±VREF/PGA Serial SPI –40 to 125

16/TSSOP, 20/TSSOP, 28/

TSSOP

3.45/4.45/ 4.95

ADS1252/4/5 24-bit, multi-channel, easy-to-use industrial delta-sigma ADCs 24 41k/

20k/30k 1/2/4 Ext 15 ppm 40/4/38 Delta-Sigma ±VREF/PGA Serial SPI –40 to 85 8/SOIC, 16/SSOP, 20/SSOP

6.45/7.17/ 6.96

ADS1259 Low noise, low drift, 14 kSPS, 24-bit industrial delta-sigma ADC 24 14.4k 1 Int/ext 10 ppm 13 Delta-Sigma ±VREF/PGA Serial SPI –40 to 105 20/TSSOP 5.60

ADS1258 16-ch, 125 kSPS, fast channel-scanning delta-sigma ADC 24 125k 16 Ext 15 ppm 42 Delta-Sigma ±VREF/PGA Serial SPI –40 to 105 48/VQFN 16.50

ADS1262/3Ultra-low noise, 32-bit ADC with PGA, internal reference, and diagnostic features

32 38k 10 Int/ext 3ppm 24 Delta-Sigma ±VREF/PGA Serial SPI –40 to 125 28/TSSOP 9.10/12.65

ADS82012.2 V to 5.5 V, low-power, 12-bit, 100 kSPS, 8-channel DAS with PGA and SPI™

12 100k 8 Ext 0.5 LSB 1.32 SAR 0 to 5.5 Serial SPI –40 to 85 24/VQFN 2.75

ADS8634/812-bit, 8-channel, bipolar SAR with software-selectable input ranges

12 1M 4/8 Int/ext 1.5 LSB 14.45 SAR ±10 Serial SPI –40 to 125 24/VQFN 2.85/3.25

ADS7042Ultra low power & ultra small size 12-bit, 1 MSPS SAR ADC with SPI interface

12 1M 1 Int 1 LSB 0.234 SAR 0 to 3.6 Serial SPI –40 to 125 8/VSSOP, 8/X2QFN 2.10

ADS8664/812-bit SAR ADC, 4/8 channels, 500 kSPS, and bipolar inputs off +5 V supply

12 500k 4/8 Int/ext 0.5 LSB 65 SAR ± 10.24 Serial SPI –40 to 125 38/TSSOP 4.00/5.00

ADS7253/7853/8353

SAR ADC, Dual, 1 MSPS/600 kSPS, 12/14/16-bit, simultaneous sampling

12/14/16 1M/600k 2 Int 1/2/2.5 LSB 42.5 SAR 0 to 5.5 Serial SPI –40 to 125 16/TSSOP,

16/WQFN3.50/

6.00/9.00


14 500k 4/8 Int/ext 0.75 LSB 65 SAR ± 10.24 Serial SPI –40 to 125 38TSSOP 9.00/12.00

ADC141S626/ ADC161S262

14-/16-bit, 50 to 250 kSPS, differential input, MicroPower ADC 14/16 250k 1 Ext 0.95/2 LSB 4.8/5.8 SAR 0 to 5.5 Serial SPI –40 to 85 10/VSSOP 2.75/5.00

ADS8319 Precision 16-bit SAR w/ SPI interface 16 500k 1 Ext 1.5 LSB 18 SAR 0 to 5.5 Serial SPI –40 to 85 10/VSSOP, 10/

VSON 6.00

ADS8684/4A/8/8A

SAR ADC with 16 bits, 4/8 channels, 500 kSPS, and bipolar inputs off +5 V supply (A = alarm)

16 500k 4/8 Int/ext 2 LSB 65 SAR ± 10.24 Serial SPI –40 to 125 38/TSSOP

10.0011.0014.0015.00


18 500k 4/8 Int/ext 5 LSB 65 SAR ± 10.24 Serial SPI –40 to 125 38/TSSOP 15.00/20.00

Programmable gain amplifiers

Part Number Description

Number of

Channels Gain(V/V)

Gain Error (±)(Max)

(%)

Slew Rate

(Typ)(V/μs)

Settling Time to 0.01%

(Typ)(μs)

Non-Linearity (±)(Max)

(%)Vs(Min)

(V)Vs(Max)

(V)

Noise at 1kHz(Typ)(nV/rt)(Hz)

Input Offset Drift (±)(Max)

(μV/C)

Input Offset (±)(Max)

(μV)

Iq(Typ)(mA)

Operating Temperature

Range(C)Pin/

Package

Approx. Price (US$)

PGA281 Zero-drift, high voltage 1

1/8,1/4, 1/2, 1, 2, 4, 8,

16, 32, 64, 128

0.15 1 20 0.0001 10 36 20 0.2 15 3 –40 to 125 16/TSSOP 2.55

PGA280 Zero drift, high voltage 4

1/8, 1/4, 1/2, 1, 2, 4, 8, 16, 32, 64, 128

0.15 1 20 0.0001 10 36 20 0.2 15 3 –40 to 125 24/TSSOP 2.90

PGA204 Programmable gain instrumentation amplifier 1 1, 10, 100,

1000 0.024 0.3 140 0.002 9 36 13 0.25 + 5/G 50 + 100/G 5.2 –40 to 85 16/SOIC16/PDIP 8.35

*Suggested resale price in U.S. dollars in quantities of 1,000. New products are listed in bold red.


Analog inputsPrecision ADCs / programmable gain amplifiers

http://www.ti.com/product/ADC141S626

http://www.ti.com/product/ADS1246














http://www.ti.com/product/LMP90097

http://www.ti.com/product/PGA204



Texas Instruments analog output solutions address a wide range of analog input modules in the factory and process automation industry, 420 mA and single ended or differential 05 V, 010 V, ±5 V and ±10 V. The TI Designs provide insights in how to handle universal output, multiple channels per module and adaptive power supplies to reduce thermal constraints in slim

modules. Industry 4.0 (Industrie 4.0) requirements for diagnostics and HART are also showcased. Small footprint and high efficiency isolated power supplies to generate positive and negative voltages help meet the demands for more channels per module and smaller form factors.

CommunicationFieldbus IN

Group Isolated Analog Output Module

Per Channel Isolated Analog Input Module

AMP

Protection

Protection

AMPControllerInterface

Memory

DigitalIsolation

DigitalIsolation

DAC

DAC

DigitalIsolation

DigitalIsolation

ControllerInterface

AMP

AMP

DAC

Protection

Protection

AMP Protection

VREF

ProtectionAMPDigital

IsolationDAC

To Field Acutators

I/V Driver

4–20 mA

Voltage Driver

0–5 V, 0–10 V, ±5 V, ±10 V

Current Driver

0–5 V, 0–10 V, ±5 V, ±10 V4–20 mA

I/V Driver

4–20 mA

Voltage Driver

0–5 V, 0–10 V, ±5 V, ±10 V

Current Driver

0–5 V, 0–10 V, ±5 V, ±10 V4–20 mA

LEGEND Logic

ADC/DACClocksOther

Power

RF/IF

ProcessorInterface

Amplifier

Digital isolators


Isolation Rating

(kVrms)

Peak Isolation Rating (Vpk)

Working Voltage (Vpk)

Forward /Reverse

Channels

Speed (Max)

(Mbps)

VCC (Min) (V)

VCC (Max)

(V)Default Output

Propagation Delay (Typ)

(ns)

Operating Temperature Range (°C) Pin/Package

Price* (US$)

ISO7420 Low-power dual-channel isolators 2500 4000 560 2/0 1 3.3 5 High 9 –40 to 105 8/SOIC 0.85

ISO7420FCCLow-power 2/0 dual-channel digital isolator with fail-safe output low and noise filter

2500 4000 560 2/0 50 3.3 5 Low 20 –40 to 85 8/SOIC 1.05

ISO7631FC 4 kVpk low-power triple-channel, 25 Mbps digital isolator 2500 4000 1414 3/1 25 2.7 5 Low 17 –40 to 125 16/SOIC 1.40

ISO7141FCC

4242-VPK small-footprint and low-power 3/1 quad-channel digital isolator with fail-safe output low

2500 4000 560 3 / 1 50 2.7 5 Low 23 –40 to 125 16/SOIC 1.90

Voltage reference


VO (V)

Temp Coeff (Typ) (ppm/°C)

Temp Coeff (Max)

(ppm/°C)

Initial Accuracy

@ 25/°C (%)

0.1–10 Hz Noise (Max)

(μVpp)

IOUT/Iz (Max) (mA)

Iq (Typ) (µA)

VIN (Min) (V)

VIN (Max)

(V)


Pin/Package

Price* (US$)

REF5020 Low noise, very low drift, precision voltage reference 2.048 2.5 3 0.05 6 10 800 2.7 18 –40 to 125 8/SOIC,

8/VSSOP 1.35

REF3325 30 ppm/°C drift, 3.9 µA, voltage reference 2.5 9 30 0.15 84 5 5 2.7 5.5 –40 to 125 3/SC-70, 3/SOT-23 0.85

LM4132 SOT-23 precision low dropout voltage reference1.024, 1.25, 2.048, 2.5,

4.09610, 20, 30 0.05 170, 190, 240,

285, 310, 350 20 60 2.2 5.5 –40 to 125 5/SOT-23 0.78

REF1941 Dual output Vref and Vref/2 voltage reference 4.096, 2.048 10 25 0.1 49.2 20 360 4.116 5.5 –40 to 125 SOT23-5 0.99

REF2041 Low-drift, low-power, dual-output VREF and VREF/2 voltage reference 4.096, 2.048 3 8 0.05 49.2 20 360 4.116 5.5 –40 to 125 SOT23-5 1.4


Analog outputsOverview


Analog inputsDigital isolators / voltage reference

http://www.ti.com/product/ISO7141FCC

http://www.ti.com/product/ISO7420

http://www.ti.com/product/ISO7420

http://www.ti.com/product/ISO7420FCC

http://www.ti.com/product/ISO7631FC

http://www.ti.com/product/LM4132

http://www.ti.com/product/REF1941




Precision DACs

Device DescriptionResolution

(Bits)No. of

Channels

INL (Max) (±LSB)

Output Range (Max)

(V or mA)

Settling Time (µs)

Output Type Interface

Reference: Type


Pin/ Package

Price* (US$)

DAC7760/8760

12/16-bit programmable current and voltage output DAC with 5 V internal reference 12/16 1 52 -11 V to 11 V,

0 to 24 mA 10Buffered voltage, current

SPI Ext, Int –40 to 125 24/HTSSOP, 40/VQFN

2.99/3.99

DAC7750/8750

12/16-bit, single channel, programmable current output DAC with 5 V internal reference 12/16 1 26 0 to 24 mA 10 Current SPI Ext, Int –40 to 125 24/HTSSOP,

40/VQFN2.49/3.49

DAC7562/ 8162/ 8562

12/14/16-bit, dual, low-power, ultra-low glitch, buffered voltage output DAC with 2.5 V, 4 ppm/°C reference

12/14/16 2 12 0 to 5 V 7 Buffered voltage SPI Ext, Int –40 to 125 10/VSSOP,

10/WSON

2.50/3.85/4.20

DAC161S055 Precision 16-bit, buffered voltage-output DAC 16 1 3 0 to 5.25 V 5 Buffered voltage SPI Ext –40 to 105 16/WQFN 2.95

DAC7716/ 8234/ 8734

12/14/16-bit quad high accuracy ±16.5 V output digital-to-analog converter 12/14/16 4 4 -16.5 to 33 V 15 Buffered

voltage SPI Ext –40 to 105 48/VQFN, 64/TQFP

8.20/14.95/20.00

DAC7718/ 8218/ 8718

12/14/16-bit octal high accuracy ±16.5 V output digital-to-analog converter 12/14/16 8 4 -16.5 to 33 V 15 Buffered

voltage SPI Ext –40 to 105 48/VQFN, 64/TQFP

8.95/13.45/16.45

DAC161P997/ S997 SPI 16-bit precision DAC for 4–20 mA loops 16 1 9 4 to 20 mA - Current Single Wire/

SPI Ext –40 to 105 16/WQFN 1.75


Adaptive power supply for PLC analog output module with output channel protection

The TIDA-00231 is a reference design for an industrial programmable logic controller (PLC) analog output module. The design provides a unique power saving solution for a digital-to-analog converter (DAC)-based analog current output module with an adaptive power supply. This adaptive power supply dynamically regulates the AVDD supply of the DAC and limits power losses to < 50 mW for typical load resistance of > 300 Ω. The analog output can source current up to 24 mA. This reference design includes the necessary on-board protection circuit and has been tested to IEC61000-4 standard EFT, ESD, and surge requirements with IO controller platforms. The protection circuitry does not negatively affect the design and test results showed typical unadjusted errors were less than 0.2% FSR and calibrated accuracy is 0.05%.

• 16-bit user configurable analog current output• Accuracy • Un-calibrated better than ±0.2% FSR at 25°C• Calibrated better than ±0.05% FSR at 25°C• Adaptive power supply reduces system power dissipation- power losses across

FET are limited to < 50 mW for typical load resistance > 300 Ω• Reverse voltage protection for analog output• On-board isolated Flybuck™ power supply with inrush current protection• Designed to comply with IEC61000-4 standards for ESD, EFT, and surge

16-Bit Analog output module reference design for programmable logic controllers (PLC)

The TIDA-00118 reference design provides a complete 4-channel, 16-bit analog output module design for programmable logic controllers (PLCs). It is designed and fully tested to meet IEC61000-4 EMC and surge requirements for industrial automation systems. The small form-factor design implements four 16-bit digital-to-analog converters with integrated output drivers capable of driving several current and voltage output ranges. Digital data and control lines are galvanically isolated from the PLC host using TI’s high-speed, 4242 V peak, digital isolator technology. The design also includes an over-current protected, isolated power supply providing all necessary module voltages. With full documentation, test results, design files and necessary firmware, the design makes it easier to evaluate complete signal chain performance and reduces time to market.

• Designed to comply with IEC61000-4 standards for ESD, EFT and surge• 4-channel 16-bit DAC based configurable analog outputs• Voltage outputs: ±10 V, 0 - 10 V, ± 5 V, 0 - 5 V• Current outputs: 0 - 20 mA, 4 - 20 mA, 0 - 24 mA• Voltage output accuracy: ± 0.2% FSR and current output accuracy: ± 0.2% FSR• Designed with output filtering, protection circuitry and integrated 15 kV ESD

protection• 24 VDC powered with on-board isolated power supplies

Analog output driver

Part Number DescriptionVs (Min)

(V)Vs (Max)

(V)Non-Linearity

(Max) (%)

Auxiliary Output Voltage

(V)Span Error (Max) (%)

Offset Voltage (±) (Max) (µV)

Offset Voltage Drift (±) (Max) (µV/°C)

Pin/ Package

Price* (US$)

XTR300 Industrial analog current/voltage output driver 10 40 0.1 17.5 0.12 1900 6 20/VQFN 1.90

XTR117 4-20 mA current loop transmitter 7.5 40 0.02 5 0.4 50 6 8/SON, 8/VSSOP 0.90



Analog outputsTI Designs / precision DACs / analog output driver

http://www.ti.com/product/DAC161P997

http://www.ti.com/product/DAC161S055

http://www.ti.com/product/DAC7562





http://www.ti.com/product/XTR117

http://www.ti.com/product/XTR300




Digital serializers

Part Number Description # of Inputs Interface

I/O max rate

(kbps)

Operating Voltage

(V)

I/O Voltage

(V) Special FeaturesI/O Current

(mA)


Price* (US$)

SN65HVS8818 input, wide 10–34 V digital-input serializer with parity for industrial digital inputs

8 SPI 1000 10 to 34 0 to 34

Parity, over temperature,

cascadable, drivers for external LEDs

0.2 to 5.2 –40 to 125 28/HTSSOP 2.00

SN65HVS880 8 input, nominal 24 V digital-input serializer for industrial digital inputs 8 SPI 1000 18 to 30 0 to 30

Voltage monitor, over temperature,

cascadable, drivers for external LEDs

0.2 to 5.2 –40 to 85 28/HTSSOP 1.90


Texas Instruments digital output solutions address a wide range of digital output modules in the factory automation industry including lowside and highside driving capabilities at 24 V nominal voltage. It also showcases solutions for pushpull high frequency outputs known as Pulse Train Output (PTO). The

TI Designs provide insights in how to handle inductive loads, isolation and protection in the digital output module. Industry 4.0 (Industrie 4.0) requirements for diagnostics is also highlighted. Thermal data and highly integrated drivers help meet the demands for more channels per module and smaller form factors.


8-ch parallel 0.5 A low side digital output module for PLC

The TIDA-00320 design is capable of delivering 0.5 A on all 8 channels in a small form factor without compromising thermal management. digital output modules are a standard component in a PLC/PAC or DCS to control actuators, motors and other resistive, capacitive or inductive loads. Customers will benefit from this integrated protected low-side driver with parallel interface as it makes the MCU interface easy to test together with a BeagleBone Black.

• High density 8 ch 24 V low side digital output• 500 mA /ch. unregulated (+20%), 2 A peak• Parallel control for simple MCU interface• Capable of switching inductive loads• LED to indicate output state and faults• BeagleBone Black cape form factor for easy evaluation


8-channel digital input module forprogrammable logic controllers(PLC)

The TIDA-00017 reference design provides a complete 8-channel digital input module front-end reference design for programmable logic controllers (PLCs). It is designed and fully tested to meet IEC61000-4 EMC and surge requirements for industrial automation systems thus reducing the time to market for customer. The design serializes 8 digital inputs, up to 34 V each, minimizing the number of isolation channels and GPIO pins required of the host interface. Serialized data and control signals are galvanically isolated from the PLC using TI’s high-speed, 4242 V peak, digital isolator technology. The design also includes an over-current protected, isolated power supply providing all necessary module voltages. Full documentation, test results, design files and necessary firmware are also available for this design.

• Fully tested to comply with IEC61000-4 for ESD, EFT and surge• Input protection circuitry and integrated 15 kV ESD protection• User-programmable current limit of 2 mA on inputs for overcurrent protection• Galvanic isolation on data and SPI data up to 4242 V peak• Integrated over-temperature indicator to disconnect inputs when fault conditions

occur• Slim form factor 95 x 50x 10 mm (LxWxH)

Texas Instruments digital inputs solutions for factory automation showcase how digital input serializers can be used to achieve higher channel density in the modules. The TI Designs also help with handle overvoltage, isolated power and data transmission in an isolated digital input module. Industry 4.0 (Industrie 4.0) requirements for diagnostics, speed and debounce filters are also highlighted.

LEGEND Logic

ADC/DACClocksOther

Power

RF/IF

ProcessorInterface

Amplifier

0 – 24 V±24V

DigitalInput

Serializer

Protection

Protection

Protection

Protection

24 V

DigitalIsolation


Field InputsFrom Sensors

CommunicationFieldbus IN

CommunicationFieldbus OUT

Digital outputOverview / TI Designs


Digital inputTI Designs / digital serializers

http://www.ti.com/product/SN65HVS880

http://www.ti.com/product/SN65HVS881



Drivers


Vs (Min)

(V)

Vs (Max)

(V)

Output Current (Max)

(A)Control

I/F


Price* (US$)

DRV8803 1 A quad relay / solenoid driver 8.2 60 2 PWM –40 to 85 20/SOIC, 16/HTSSOP 1.40

DRV8804 1 A quad relay / solenoid driver 8.2 60 2 Serial –40 to 85 20/SOIC, 16/HTSSOP 1.40

DRV8806 1 A quad relay / solenoid driver w/ open load detect 8.2 40 2 Serial –40 to 85 16/HTSSOP 1.25

DRV8844 1.75 A quad high-side / low-side driver 8 60 2.5 PWM –40 to 85 28/HTSSOP 2.50

DRV8860 200 mA octal low-side driver w/ open load detect 8 38 0.56 Serial –40 to 85 16/TSSOP 1.50

*Suggested resale price in U.S. dollars in quantities of 1,000. Preview products are listed in bold blue.

Name Description Key Features

Low side 0.5A 8ch digital output module for PLC

The TIDA-00236 design is capable of delivering 0.5 A on all 8 channels in a small form factor without compromising thermal management. Digital output modules are a standard component in a PLC/PAC or DCS to control actuators, motors and other resistive, capacitive or inductive loads. Customers will benefit from this integrated protected low-side drivers and the low pin count control interface which saves pins and isolation channels.

• High density 8 ch 24 V low side digital output• 500 mA /ch unregulated (+20%), 2 A peak• Data serializer to save isolation channels• Capable of switching inductive loads• LED to indicate output state and faults• Standalone use or with TIDA-00123

8 channel 1A/Ch high side driver for programmable logic controller (PLC) reference design

The TIDA-00183 reference design shows a high-density, high-power digital output circuitry with full protection and isolation for programmable logic controllers in factory automation and control environment. The BeagleBone-Black cape form factor allows easy evaluation of the used driver chips and the interoperation with an MSP430 MCU for innovative protection schemes.

• High-density 8-channel, 24 V high-side output• 1 A/channel unregulated (+20%), 3-A peak• 4-wire SPI MCU interface• Fast switching of inductive loads• LEDs to indicate output state• BeagleBone Black cape form factor for easy evaluation (four boards stackable)

High performance pulse train output (PTO) with PRU-ICSS for industrial applications

The TIDEP0027 high performance pulse train output (PTO) with PRU-ICSS for industrial application combines the AM335x SitaraTM processor family from Texas Instruments (TI) and the PTO module into a single system-on-chip (SoC) solution. The design is based on the TMDSICE3359 Industrial communications engine (ICE) but can be also used with other PRU-ICSS capable development boards.

• High speed/frequency with high precision for accurate PTO control and synchronization

• Implementation without external ASIC or FPGA• Implementation on PRU-ICSS with Sitara processor• Contains PRU-ICSS firmware in source code and can get adoptable by customer• Easy evaluation with TMDSICE3359 Industrial Communication Engine (ICE) EVM

24 VDC 10 A eFuse and protection circuit for programmable logic controllers (PLC)

This sub system design (TIDA-00233) shows an IC based implementation of over-voltage, over-current, reverse current, reverse polarity and miss wire protection which is more accurate, lower power and faster compared to fuses, PTCs and diodes. Programmable logic controller (PLC) I/O modules connected to a field power supply benefit from protection on the 24 V field input connectors as power supply faults or miss wiring might damage or cause the module to not operate correctly.

• Short circuit protection• Over-and under-voltage protection• Reverse polarity protection• Miss wire and reverse current protection • Surge protection (IEC61000-4-5)• This reference design is tested with HW and includes a design guide

TI Designs

Connectivity options ranging from Ethernet ports to UARTs to simple SPI ports are required. Ethernet enables integration of field devices to the corporate enterprise network. There are a number of fieldbus options – both serial (RS485, DeviceNet™,

PROFIBUS®, CAN, etc.) and Ethernet based. Extended cable reach and diagnostics to debug wire breaks provides system designers significant value. Integrated digital isolation on the interface transceivers is highly desirable to reduce board space.

Connectivity & interface for I/O moduleOverview / microcontrollers

Microcontrollers Part Number Description Core Communication Interface Analog I/O End Equipment

MSP MCUs

16- and 32-bit mixed-signal processors designed for ultra-low-power sensing applications, including those operating on a current loop; portfolio features up to 48 MHz, 512 KB non-volatile memory (Flash/FRAM), 64 KB SRAM and smart analog and digital peripherals

MSP430™/ ARM® Cortex™-M4 I2C, SPI, UART, USB, IrDA

24-bit SD ADCs, 14-bit SAR

ADCs, DACs, Op Amps,

Comparators, LCD

Sensor transmitters, metering solutions,current loop controllers

C2000™ C2000 32-bit real-time MCU optimized for processing, sensing and actuation to improve closed loop performance Proprietary UART, I2C, SPI, USB ADC, DAC I/O modules & communication modules

TM4C Industrial grade 10/100/1000 Ethernet physical layer transceiver ARM Cortex-M4 UART, I2C, SPI, CAN,ethernet, USB ADC, DAC I/O modules & communication modules

RM4x RM4x ARM Cortex-R4-based microcontroller for safety-critical applications up to 220 MHz and 3 MB flash ARM Cortex-R4 UART, I2C, SPI, CAN,

ethernet, USB ADC, DAC Safety

TMS570 TMS570 ARM Cortex-R4F-based microcontroller for safety-critical applications up to 160 MHz and 2 MB flash ARM Cortex-R4 UART, I2C, SPI, CAN,

ehernet, USB ADC, DAC Safety


Digital outputTI Designs (continued) / drivers

http://www.ti.com/product/DRV8803







http://www.ti.com/tool/TIDEP0027


LVDS devices

Device Description FeatureSupply input Channel

Signal rate

(Mbps) Input OutputOperating Temperature

Range (°C)Pin/

PackagePrice* (US$)

DS90LV001 Single channel, 800 Mbps LVDS buffer

Interoperable with LVPECL and LVDS, tri-state output, low jitter 3.3 1 800

LVDSLVPECL

CMLLVDS –40 to +85 8/WSON

8/SOIC 0.76

DS90LV011A Single channel, 400 Mbps, LVDS driver Power off protection, low power 3.3 1 400 LVTTL LVDS –40 to +85 5/SOT-23 0.42

DS90LT012A Single channel, 400 Mbps, LVDS receiver

Power off protection, low power, integrated termination 3.3 1 400 LVDS LVTTL –40 to +85 5/SOT-23 0.49

DS90LV047A Quad channel, 400 Mbps, LVDS driver

Low power, supports tri-state function 3.3 4 400 LVTTL LVDS –40 to +85 16/SOIC

16/TSSOP 1.09

DS90LV048A Quad Channel, 400 Mbps, LVDS receiver

Low power, supports tri-state function 3.3 4 400 LVDS LVTTL –40 to +85 16/SOIC

16/TSSOP 1.09

LVC


VCC(Min)(V)

VCC(Max)

(V) Bits(#)Voltage

(Nom)(V)

F @ Nom Voltage

(Max)(Mhz)

ICC @ Nom Voltage

(Max)(mA)tpd @ Nom

Voltage(Max)(ns)Operating Temp. (°C) Pin/ Package

Price* (US$)

SN74LVC1G57 Configurable multiple-function gate 1.65 5.5 1 1.8, 2.5, 3.3, 5 150 0.01 14.4, 8.3, 6.3, 5.1 –40 to 125 DSBGA, SC70, SON, SOT,

SOT-23 0.07

SN74LVC14A Hex Schmitt-trigger inverter 2 3.6 6 1.8, 2.5, 2.7, 3.3 100 0.01 11, 7.8, 7.5, 6.4 –40 to 125 SO, SOIC, SSOP, TSSOP,

TVSOP, VQFN 0.07

SN74LVC1G125 Single bus buffer gate with 3-state outputs 1.65 5.5 1 1.8, 2.5, 3.3, 5 150 0.01 9, 5.5, 4.5, 4 –40 to 125,

–40 to 85DSBGA, SC70, SON, SOT,

SOT-23, X2SON 0.07

SN74LVC1G17 Single Schmitt-trigger buffer 1.65 5.5 1 1.8, 2.5, 3.3, 5 150 0.01 11, 6.5, 5.5, 5 –40 to 125,

–40 to 85DSBGA, SC70, SON, SOT,

SOT-23, X2SON 0.07

SN74LVC00A Quadruple 2-input positive-NAND gate 1.65 3.6 1.8, 2.5, 2.7, 3.3 150 0.04 12.5, 6.4, 5.1, 4.3 –40 to 125 SO, SOIC, SSOP, TSSOP,

VQFN 0.05

SN74LVC244A Octal buffer/driver with 3-state outputs 1.65 3.6 8 1.8, 2.5, 2.7, 3.3 100 0.04 14.4, 10.4, 7.4, 6.7, 5.7 –40 to 125,

–40 to 85

BGA MICROSTAR JUNIOR, PDIP, SO, SOIC, SSOP, TSSOP, TVSOP, VQFN

0.08u

SN74LVC541A Octal buffer/driver with 3-state outputs 1.65 3.6 8 1.8, 2.5, 2.7, 3.3 100 0.01 15.7, 7.8, 5.6, 5.1 –40 to 125

–40 to 85SO, SOIC, SSOP, TSSOP,

TVSOP, VQFN 0.14

SN74LVC245A Octal bus transceiver with 3-state outputs 1.65 3.6 8 1.8, 2.5, 2.7, 3.3 100 0.03 12.7, 8.3, 7.3, 6.3 –40 to 125

BGA MICROSTAR JUNIOR, PDIP, SO, SOIC, SSOP, TSSOP, TVSOP, VQFN

0.12


Logic

Industrial interface transceivers


Bus Fault Voltage

(V)

ICC (Max) (mA)

Number of Nodes Date Duplex ESD

Supply Voltage(s)

(V)Special

Features


Price* (US$)

DS75176BT 5 V, multipoint RS-485/RS-422 transceivers –10 to 15 55 32 10 Mbps Half +500V HBM +4.75 to

+5.25 Industry standard –40 to 85 8/SOIC, 8/PDIP 0.52

DS485 5 V, low power, half-duplexRS-485/RS- –14 to 14 0.9 32 2.5 Mbps Half +2kV HBM +4.75 to

+5.25Low power

(Typical ICC = 200uA) –40 to 85 8/SOIC, 8/PDIP 0.87

SN65HVD773.3 V, full-duplex RS-485, 12 kV IEC ESD, 50 Mbps data rate, no enables

–13 to 16.5 1.1 96 50 Mbps Full

±30-kV HBM protection±12-kV IEC61000-4-2

Contact Discharge±4-kV IEC61000-4-4 Fast

Transient Burst

3.3 High ESDLow power –40 to 125 8SOIC

8MSOP 1.9

SN65HVD783.3 V, half-duplex RS-485, 12 kV IEC ESD, 50 Mbps data rate

.95 200 50 Mbps Half

±15 kV HBM Protection±12 kV IEC 61000-4-2

Contact Discharge±4 kV IEC 61000-4-4 Fast

Transient Burst

3.3 High ESDLow power –40 to 125

8SOIC 8SON 8VSSO

1.0

SN65HVD1176 PROFIBUS® RS-485 transceiver –9 to 14 6 160 40 Mbps Half ±10-kV HBM 5

Low bus capacitance Exceeds PROFIBUS

requirements of 2.1 V with voltage at 54 V

–40 to 85 8SOIC 1.54

SN65HVD255CAN transceiver with fast loop times for highly loaded networks

–27 to 40 85 167 1 Mbps High speed, turbo short prop delay, silent mode 4.5 to 5.5 Meets the Requirements

of ISO11898-2 -40 to 125 8SOIC 0.50

SN65HVD256CAN transceiver With Fast Loop Times for Highly Loaded Networks

–27 to 40 85 167 1 Mbps High speed, turbo short prop delay, RXD I/O supply

4.5 to 5.5 2.8 to 5.5

Meets the Requirements of ISO11898-2 -40 to 125 8SOIC 0.50

TRS3253E7RS-232 transceiver with 1.8 V logic supply and IEC-ESD protection

1 1 Mbps

±8 kV IEC 61000-4-2 air-gap discharge, ±8 kV IEC 61000-4-2 contact

discharge, ±15 kV human body model

3 to 5.5 Logic supply pin with 1.8 support –40 to 85 32/VQFN 1.12



Connectivity & interface for I/O moduleIndustrial interface transceivers / LVDS devices / logic: LVC

http://www.ti.com/product/DS485

http://www.ti.com/product/DS75176BT

http://www.ti.com/product/DS90LT012A

http://www.ti.com/product/DS90LV001

http://www.ti.com/product/DS90LV011A



http://www.ti.com/product/SN65HVD1176





http://www.ti.com/product/SN74LVC00A


http://www.ti.com/product/SN74LVC1G125






To protect against transients and ground loops, the module is electrically isolated from the control side. The design can be customized for perfor mance and cost by using a DCDC converter. Finally, using LDOs with good PSRR (power supply rejection ratio) to supply the precision analog circuitry will reduce the power supply ripple and preserve system accuracy and resolution.

Analog ±5 V, ±10 V, ±15 V, ±10 VDigital 1.0 V, 1.8 V, 3.3 V, 5 V

12-24 VBackplane

Isolation barrier

DC/DC LDO Isolated DC/DC

DC/DC

SupervisorSequencer

E-Fuse & Protection

5 V, 3.3 V, 1.8 V, 1.0 V


1 W small form factor power supply with isolated dual output for PLC I/O modules

The TIDA-00129 reference design is a 1 W power supply with dual isolated outputs for space constrained applications. With 24 V and 3.3 V isolated outputs, this design was created specifically to power programmable logic controller (PLC) I/O modules in a factory automation setting. This design was created to comply with IEC 61010-1, which in turn will provide a designer faster time to market with their own design.

• Designed to comply with IEC61010-1 • Small form factor for space constrained I/O cards: 51 x 40 x 5.97 mm

(L x W x H) • Up to 87% efficiency for low heat dissipation in small plastic housings • A complete and cost effective design for I/O cards • ±10% output voltage accuracy • Wide input voltage range: 1 7V to 36 V (24 VNOM)

Isolated power supply for programmable logic controller (PLC) I/O modules reference design

The TIDA-00400 isolated power supply reference design provides multiple isolated outputs to supply the bias voltage needed in a programmable logic controller (PLC) IO module. It generates 3 isolated outputs: ±15 V@30 mA and +5 V@4 0mA. These voltage rails can satisfy most of the required voltage rails in the I/O modules, such as the op-amp, DAC bias, RS-485 transmitter and digital isolator power supplies.

• Wide input voltage range: 18 to 30 V (24 VNOM)• Non-Isolated output: 3.3 V with 50 mA• Three isolated outputs: +15 V with 30 mA -15 V with 30 mA +5 V with 4 0mA• Small form factor for space constrained I/O cards 51 x 51 x 8 mm (L x W x H)• Primary-side regulation (no need for optocoupler) increases lifetime reliability

Adaptive power supply for PLC analog output module with output channel protection

The TIDA-00231 is a reference design for an industrial programmable logic controller (PLC) analog output module. The design provides a unique power saving solution for a digital-to-analog converter (DAC)-based analog current output module with an adaptive power supply. This adaptive power supply dynamically regulates the AVDD supply of the DAC and limits power losses to < 50 mW for typical load resistance of > 300 Ω. The analog output can source current up to 24 mA. This reference design includes the necessary on-board protection circuit and has been tested to IEC61000-4 standard EFT, ESD, and surge requirements with I/O Controller platforms. The protection circuitry does not negatively affect the design and test results showed typical unadjusted errors were less than 0.2% FSR and calibrated accuracy is 0.05%.

• 16-bit user configurable analog current output• Accuracy • Un-calibrated better than ±0.2% FSR at 25°C• Calibrated better than ±0.05% FSR at 25°C• Adaptive power supply reduces system power dissipation- power losses across

FET are limited to < 50 mW for typical load resistance > 300 Ω• Reverse voltage protection for analog output• On-board isolated Flybuck™ power supply with inrush current protection• Designed to comply with IEC61000-4 standards for ESD, EFT, and surge

Isolated DC/DC power supply for PLC analog input and output modules

The TIDA-00401 reference design is an isolated DC/DC turn-key solution. For a 10 W isolated power supply with wide input voltage range, no opto-coupler feedback and low number of external components the Flybuck™ topology is superior to a flyback design. The single side populated PCB board provides a convenient tool for evaluation and on-the-fly optimization of the design, with adequate headers, jumpers and test points for applications like PLC analog Input/Output modules.

• Isolated DC/DC power supply for 15 V to 36 V Input, up to 10 W of output power• Low quiescent current up to 20 mA• Open-loop, optocoupler-less design• Synchronization output and fixed switching frequency enable use in noise

sensitive applications• Flexible configurable board enables easy evaluation and modification• Design guide provides detailed description and performance test data

16-Channel status LED driver for PLC modules reference design

The objective of the TIDA-00560 reference design is to demonstrate a multi-channel LED driver as required in PLC I/O modules to indicate the status of several analog, digital input, and output channels. Important requirements for such a design like low static current, low component count, minimal PCB requirements, and an integrated LED diagnostic features are addressed with this design. The two-layer single-side component mounted board is compatible with the BeagleBone cape specification for rapid evaluation with the BeagleBone platform.

• 16-channel shift register with wide range constant current sinks (2-35 mA)• Two-level selectable LED brightness to compensate for ambient light• Diagnostic features: LED open and LED shorted to ground• Standardized SPI connects seamlessly to standard processors• Number of channels can be increased by daisy-chaining multiple LED driver

devices• BeagleBone cape support for easy evaluation

Ultra-small 1 W, 12 V-36 V iso power supply for analog prog logic controller modules

Analog input and output modules are a standard component in programmable logic controllera (PLC) or distributed control systems (DCS). More channels per module and slimmer modules bring design challenges to the isolated power supply in those modules. Anyone facing those challenges will benefit from TIDA-00237, as the total design footprint is less than 2.54x2.54 mm and less than 5 mm height. It uses a Flybuck approach which means no optocoupler feedback with wide input voltage range of 12V-36 V. The design provides ±15 V and 5 V isolated, low noise outputs optimal for driving a data converter or analog front end.

• Wide input voltage range: 12 V to 36 V (24 VNOM)• 3 isolated outputs: 15 VISO at 3 0mA ultra low noise, -15 VISO at 30 mA ultra

low noise, 5 VISO at 40 mA• ±2.5% output voltage accuracy• Ultra low profile < 5 mm• IEC 61131-2 compliant


Power for I/O moduleOverview / TI Designs








LDO linear regulators

Part Number Description Output Options

Iout (Max)

(A)

VIN (Min) (V)

VIN (Max)

(V)

VOUT (Min) (V)

VOUT (Max)

(V)Iq (Typ)

(mA)

Vdo (Typ) (mV)

Noise(uVrms) Additional Features


Pin/Package

Price* (US$)

TLV1117Single output LDO, 800 mA, fixed and Adj., internal current limit, thermal overload protection

Adjustable output 0.8 2.7 25 1.25 13.7 0.08 1200 Overcurrent protection, thermal shutdown

–40 to 125, 0 to 125

DDPAK/TO-263, SON, SOT-223, TO-220, TO-252

0.18

LM317 3/4 Pin 1.5A adjustable positive voltage regulator

Adjustable output, programmable output 0.03 1.4 5.5 Fixed

outputsFixed

outputs 0.05 2000 Overcurrent protection, thermal shutdown 0 to 125

DDPAK/TO-263, PFM, SOT-223, TO-220

0.18

UA78L05 3/8 Pin 100 mA fixed 5 V positive voltage regulator Fixed output 0.15 2.7 30 Fixed

outputsFixed

outputs 3.8 1700 42 Overcurrent protection, thermal shutdown 0 to 125 SOIC, SOT-

89, TO-92 0.09

LP2985-50Single output LDO, 150 mA, fixed(5.0 V), 1.5% tolerance, low quiescent current, low noise

Fixed output 0.03 1.4 5.5 Fixed outputs

Fixed outputs 0.85 280 30 Overcurrent protection,

thermal shutdown –40 to 125 SOT-23 0.18

TPS709 30 V, 150 mA, Ultra-low Iq low-dropout regulator

Fixed 1.2 V, 1.35 V, 1.5 V, 1.6 V, 1.8 V, 1.9 V, 2.5 V, 2.8 V, 3.0 V, 3.3 V, 3.6 V, 3.8 V, 3.9 V, 5.0 V, 6.0 V

0.15 2.7 30 Fixed outputs

Fixed outputs 0.001 300

Reverse current protection, enable, overcurrent protection, thermal

shutdown

–40 to 125 5/SOT, 6/SON 0.39

TLV733PCapacitor-free, 300 mA, Low-dropout regulator with foldback current limit

Fixed 1.0 V, 1.1 V, 1.2 V, 1.5 V, 1.8 V, 2.5 V, 2.8 V,

2.85 V, 3.0 V, 3.3 V0.03 1.4 5.5 Fixed

outputsFixed

outputs 0.034 122

Enable, stable without output capacitors, foldback

overcurrent protection, output discharge, thermal

shutdown

–40 to 125 5/SOT, 4/SON 0.17

TPS7A4901VIN 3 V to 36 V, 150 mA, ultra-low noise, high PSRR, low-dropout linear regulator

Adjustable output 0.15 3 36 1.2 33 0.06 260Over current protection,

thermal shutdown, enable, soft start

–40 to 125 8/MSOP-PowerPAD 1.10

TPS7A3001VIN –3 V to –36 V, –200 mA, ultra-low noise, high PSRR, low-dropout linear regulator

Adjustable output, negative output 0.2 –3 –36 –1.18 –33 0.05 216

Soft start, enable, over current protection,

thermal shutdown–40 to 125 8/MSOP-

PowerPAD 1.50

DC-DC regulators


VIN (Min)

(V)

VIN (Max)

(V)

VOUT (Min)

(V)

VOUT (Max)

(V) Iout (A) Topology

Switch Current

Limit (Typ) (A)

Iq (Typ) (mA)

Duty Cycle (Max) (%) Soft Start Compensation Special Features


Range (°C)

Pin/Package

Price* (US$)

TPS62097

2 A step down converter with selectable switching frequency in HotRod™ package

2.5 6 0.8 6 2 Buck 3.6 0.04 100 Adjustable Internal

Enable, light load efficiency, output

discharge, power good, pre-bias start-Up, synchronous rectification,tracking

–40 to 125 11VQFN —

TPS6217528 VIN, 0.5 A step-down converter with DCS-Control™

4.75 28 1 6 0.5Buck,

synchronous buck

1 0.022 100 Adjustable InternalEnable, light load

efficiency, sleep mode, power good

–40 to 85 10/SON 0.70

TPS621503–17 V 1 A step-down converter with DCS-Control™

3 17 0.9 6 1Buck,

synchronous buck

1.7 0.017 100 Adjustable Internal

Enable, light load efficiency, power

good, tracking, voltage margining

–40 to 85 16/QFN 0.98

TPS54062/61

4.7 V to 60 V input, 50 mA/200 mA synchronous step-down converter

4.5 60 0.8 58 0.050/0.200 Buck 0.13/0.35 0.09 98 Fixed External

Enable, frequencysynchronization, light

load efficiency–40 to 125 8/SON, 8/

VSSOP 0.88

LM5017100 V, 600 mA constant on-time synchronous buck regulator

9 100 1.25 90 0.6

Constant on-time

synchronous buck

1.3 1.75 90 ExternalNo

compensation needed

Intelligent current limit, primary-side Flybuck™

regulation–40 to 125

8/SO PowerPAD, 8/WSON

1.57

*Suggested resale price in U.S. dollars in quantities of 1,000. New products are listed in bold red

Input power protection


VIN (Min) (V)

VIN (Max) (V)

Current Limit Threshold (A) Enable Fault Response Special Features


Price* (US$)

LM5069 Positive high voltage hot swap / inrush current controller with power limiting 9 80 46.5 Yes Auto retry

latch off –40 to 125 10/VSSOP 1.47

LM5060 High-side protection controller with low quiescent current 5.5 65 Externally

adjustable Yes Latch off No external RSENSE –40 to 125 10/VSSOP 1.09

LM5050 High side OR-ing FET controller 5 75 AUX input oring control –40 to 125 6/SOT 0.87


Power for I/O moduleInput power protection / LDO linear regulators / DCDC regulators



http://www.ti.com/product/LM5050-1



http://www.ti.com/product/LP2985-50

http://www.ti.com/product/TLV1117

http://www.ti.com/product/TLV733P

http://www.ti.com/product/TPS54062




http://www.ti.com/product/TPS7A3001

http://www.ti.com/product/TPS7A4901

http://www.ti.com/product/UA78L05


Window comparator


Vs (Min)

(V)

Vs (Max)

(V)

tRESP Low-to-High

(µs)

Vos (Offset Voltage @

25°C) (Max) (mV)

Iq per Channel

(Max) (mA)Output Type

Input Bias Current

(±) (Max) (nA)

Number of Channels Special Features

Rail-Rail


Pin/Package

Price* (US$)

TPS370136 V window comparator with internal ref for over- and undervoltage detection

1.8 36 28 5.5 0.011 Open drain 25 1 Hysteresis, internal

reference In –40 to 125 6/SOT 0.89

LMV762 Low voltage, precision comparator with push-pull output 2.7 5 0.12 1 0.7 Push-pull 0.005 2 –40 to 125 8/SOIC,

8/VSSOP 0.85

TPS3700High-voltage (18 V) window comparator with over- and undervoltage detection

1.8 18 29 5.5 0.013 Open drain 25 1 Hysteresis, internal

reference In –40 to 125 6/SOT, 6/WSON 0.70


Texas Instruments communication module solutions address the increasing demand for industrial communication connectivity on remote I/Os, bus couplers, motor drives, field transmitters or Intelligent electric devices (IED). TI Designs based on the SitaraTM processors help customers to realize Profibus®, Profinet®, EtherCAT®, Ethernet I/PTM, POWERLINK and Sercos III slave nodes that can run the whole application

by itself or connect to an application processor. Industry 4.0 (Industrie 4.0) support for multiple industrial Ethernet protocols are met with this platform which also allows for scalability depending on processing requirements and power budget. The reference designs also give insight in power management, interface and interconnect to input and output devices.

Industrial ethernet protocols designsName Description Key Features

EtherCAT® Communications Development Platform Targeted for EtherCAT slave communications, this development platform

(TIDEP0001) allows designers to implement real-time EtherCAT communications standards in a broad range of industrial automation equipment. It enables low footprint designs in applications such as industrial automation, factory automation or industrial communication with minimal external components and with best-in-class low-power performance.

• EtherCAT conformance tested by EtherCAT Technology Group (ETG)• Free EtherCAT Slave Stack Code (SSC) from Beckhoff available; requires ETG

membership (free of charge) and valid EtherCAT Vendor ID• Free board support package and industrial software development kit from TI• Support other industrial communications with the same hardware (e.g., PROFIBUS®,

PROFINET®, Ethernet/IPTM and more)• Production ready development platform sub-system which includes schematics, BOM,

user guides, application notes, white paper, software, demos and more

PROFIBUS Communications Development Platform Targeted for PROFIBUS slave communications, this development platform

(TIDEP0002) allows designers to implement PROFIBUS communications standards in a broad range of industrial automation equipment. It enables low footprint designs in applications such as industrial automation, factory automation or industrial communication with minimal external components and with best-in-class low-power performance.

• AM335x ARM® Cortex®-A8 processor-based design enables 40% system BOM savings by eliminating external ASIC/FPGA

• Access to other peripherals and interfaces for a scalable HMI, PLC and I/O solution• PROFIBUS slave certified by Siemens authorized test labs• Pre-tested protocol stack for evaluation• Free board support package and industrial software development kit from TI• Support other industrial communications with the same hardware (e.g., EtherCAT,

Profinet, Ethernet/IP and more)• Production ready development platform sub-system includes schematics, BOM, user

guides, application notes, white paper, software, demos and more

Communication module and PLC controllerOverview / microprocessors / industrial ethernet protocols designs

MicroprocessorsPart Number Description Core Communication Interface Analog I/O End Equipment

Sitara™ AM335x

Sitara™ processors with ARM® Cortex™-A8 core and integrated industrial communications support ARM® Cortex™ - A8 USB, UART,I2C, SPI, Industrial

Ethernet ADC Communication modulePLC controller (CPU)

Sitara AM4xxx

Sitara processors with ARM Cortex-A9 core with integrated industrial communications support ARM Cortex - A9 USB, UART, I2C, SPI, Industrial

Ethernet

12-bit SAR ADC0

12-bit SAR ADC1

Motor controlPLC controller (CPU)

Sitara AM5xxx

Sitara processors with ARM Cortex-A15 core with integrated industrial communications support and DSP acceleration for analytics processing

ARM Cortex - A15 USB, UART, I2C, SPI, Industrial Ethernet PMIC PLC controller (CPU)

66AK2L06 High-performance DSP+ARM SoC with integrated digital front end (DFE) and JESD204B

ARM Cortex-A15 and C66x DSP

UART, I2C, SPI, Ethernet, USB, JESD204B DFE Communication modules

PLC controller (CPU)


Power for I/O moduleWindow comparator

http://www.ti.com/product/LMV762





http://www.ti.com/sitara

http://www.ti.com/product/66AK2L06

Name Description Key Features

PROFINET communications development platform

Targeted for PROFINET slave communications, this development platform (TIDEP0008) allows designers to implement PROFINET communications standards in a broad range of industrial automation equipment. It enables low foot print designs in applications such as industrial automation, factory automation or industrial communication with minimal external components and with best in class low power performance.

• AM335x ARM Cortex-A8 processor-based design enables 30% system BOM savings by eliminating external ASIC/FPGA

• PROFINET IO Device for conformance classes A and B certified by COMDEC• High performance PROFINET cut-through switch supports 250 µs cycle time with 8

real-time connections.• Very robust PROFINET switch with 4 priority queues per port and content filter passing

Netload class 3.• Free board support package and industrial software development kit from TI• Support other industrial communications with the same hardware (e.g., EtherCAT,

PROFIBUS, Ethernet/IP and more)• Production Ready development platform sub-system which includes schematics, BOM,


Certified PROFINET IRT V2.3 device with 1 GHz ARM application processor reference design

Certified hardware and software components for Profinet IRT V2.3 device applications. This design (TIDEP0029) integrates Industrial Ethernet Phys, Profinet IRT switch, Profinet IRT stack and application example in one package. Profinet is the leading Industrial Ethernet standard used by many Industrial segments and end-equipment which require real-time deterministic exchange of IO data and additional bandwidth for service and diagnostics.

• Profinet Conformance Class A/B/C• 250 µs cycle time• 1 step time synchronization (PTCP)• 8 consumer and provider protocol machines• MRP – Media Redundancy Protocol• Integrated with Molex Profinet stack• Integrated with Interniche SNMP stack

Ethernet/IP communications development platform Targeted for Ethernet/IP slave communications, this development platform

(TIDEP0003)allows designers to mplement Ethernet/IP communications standards in a broad range of industrial automation equipment. It enables low foot print designs in applications such as industrial automation, factory automation or industrial communication with minimal external components and with best in class low power performance.

• AM335x ARM Cortex-A8 processor-based design enables 30% system BOM savings by eliminating external ASIC/FPGA

• Access to other peripherals and interfaces for a scalable HMI, PLC and I/O solution• Free board support package and industrial software development kit from TI• Support other industrial communications with the same hardware (e.g., EtherCAT,

PROFIBUS, PROFINET and more)• Production Ready development platform sub-system which includes schematics, BOM,


Powerlink on TI SitaraTM processors The TIDEP0028 Ethernet Powerlink development platform combines the AM335x

Sitara processor family from Texas Instruments (TI) and the Powerlink open media access control (MAC) layer into a single system-on-chip (SoC) solution. Targeted for Ethernet Powerlink slave communications, the TIDEP0028 allows designers to implement the real-time Powerlink communication standard for a broad range of industrial automation equipment. The design is based on the TMDSICE3359 industrial communications engine (ICE).

• Ethernet Powerlink conformance tested• Ethernet Powerlink firmware for PRU-ICSS with openMAC compliant register interface• Board support package and industrial software development kit available from TI and 3rd

party• Development platform includes schematics, BOM, user guides, application notes, white

paper, software, demos and more• Supports other industrial communications with the same hardware (e.g., EtherCAT,

PROFINET, Ethernet/IP and more)

Sercos III communications development platform The TIDEP0010 Sercos III communication development platform combines the

AM335x Sitara processor family from Texas Instruments (TI) and the Sercos III media access control (MAC) layer into a single system-on-chip (SoC) solution. Targeted for Sercos III slave communications, the TIDEP0010 allows designers to implement the real-time Sercos III communication standard for a broad range of industrial automation equipment. The design is based on the TMDSICE3359 Industrial Communications Engine (ICE).

• Sercos III conformance tested• Sercos III firmware for PRU-ICSS with Sercos MAC compliant register interface• Board support package and industrial software development kit available from TI and

3rd party• Development platform which includes schematics, BOM, user guides, application notes,

white paper, software, demos and more• Supports other industrial communications with the same hardware (e.g., EtherCAT,

PROFINET, Ethernet/IP and more)

Sercos III Slave for AM437x – Communication development platform

The TIDEP0039 Sercos III Slave For AM437x Communication Development Platform Reference Design combines the AM437x Sitara processor family from Texas Instruments (TI) and the Sercos III media access control (MAC) layer into a single system-on-chip (SoC) solution. Targeted for Sercos III slave communications, the TIDEP0039 allows designers to implement the real-time Sercos III communication standard for a broad range of industrial automation equipment. The design is based on the TMDXIDK437X industrial development kit (IDK).

• Sercos III conformance tested• Sercos III firmware for PRU-ICSS with Sercos MAC compliant register interface• Board support package and industrial development kit available from TI and 3rd party• Development platform includes schematic, BOM, user guides, application notes, white

paper, software, demos and more• Supports other industrial Ethernet communication standards with the same hardware

(e.g. EtherCAT, PROFINET, Ethernet/IP and more)

Multi-Protocol industrialethernet detection withPRU-ICSS

Industrial Ethernet for industrial automation exist in more than 30 industrial standards. Some of the well-established real-time Ethernet protocols, like EtherCAT, EtherNet/IP, PROFINET, Sercos III and Powerlink require dedicated MAC hardware support in terms of FPGA or ASICs. The programmable real-time unit inside the Industrial Communication Subsystem (PRU-ICSS), which exists as HW block inside the Sitara processors family, replaces FPGA or ASICS by a single chip solution. A firmware in the PRU-ICSS detects the type of industrial Ethernet protocol and loads the appropriate industrial application during run-time into the Sitara processor. The TIDEP0032 reference design describes the multi-protocol industrial Ethernet protocol detection firmware for PRU-ICSS.

• High speed/frequency with high precision for accurate PTO control and synchronization• Implementation without external ASIC or FPGA• Implementation on PRU-ICSS with Sitara processor• Contains PRU-ICSS firmware in source code and can get adoptable by customer• Easy evaluation with TMDSICE3359 industrial communication engine (ICE) EVM

Industrial ethernet protocols designs


Communication module and PLC controllerIndustrial ethernet protocols designs (continued)











Ethernet physical layer transceiver (PHY)

Part Number Description Interface

Cable Length

(m)LED (#)

Supply Voltage

(V)Data Rate

(Mbps) JTAG 1149.1Port

Count Special Features


Price* (US$)

DP83848I

Industrial temperature 10/100 Ethernet physical layer transceiver in QFP packaging

MII/RMII/SNI 150 3 3.3 10/100 Yes Single25 MHz clock out, EMI

mitigation circuitry, industry gold standard

–40 to 85 QFP-48 2.20

DP83848K

Industrial temperature 10/100 Ethernet physical layer transceiver in QFN packaging

MII/RMII 137 2 3.3 10/100 Yes Single EMI mitigation circuitry, industry gold standard –40 to 85 QFN-40 0.95

DP83867IRPAP

Industrial grade QFP packaging 10/100/1000 Ethernet physical layer transceiver

RGMII/GMII/MII 130 4 2.5, 1.1 10/100/1000 Yes Single

Cable diagnostics, IEEE 1588 start of frame detect, wake on LAN, integrated

termination resistors

–40 to 85 QFP-64 6.40

DP83867IRRGZIndustrial grade 10/100/1000 Ethernet physical layer transceiver

RGMII 130 4 2.5, 1.0 10/100/1000 Yes Single



–40 to 85 QFN-48 6.40

DP83867ISIndustrial grade with SGMII 10/100/1000 Ethernet physical layer transceiver

SGMIIRGMII 130 4 2.5, 1.0 10/100/1000 Yes Single



–40 to 85 QFN-48 7.27

DP83867E

Extended temperature grade with SGMII 10/100/1000 Ethernet physical layer transceiver

SGMIIRGMII 130 4 2.5, 1.0 10/100/1000 Yes Single



–40 to 105 QFN-48 8.36

eFuses

Part Number DescriptionVin (Max)

(V)Imax (A)

Ron (mΩ)

Current Limit Accuracy Channels Special Features

Operating Temp. (°C)

Pin/ Package

Price*(US$)

TPS25927 18 V, 5 A, 28 mΩ eFuse with BFET driver for reverse current protection 4.5 to 18 5 28 ±8% 1 Reverse current protection, thermal

shutdown, undervoltage protection –40 to 85 10VSON 0.55

TPS25921 18 V, 1.6 A, 90 mΩ eFuse with adjustable ±2% accurate current limit 4.5 to 18 1.6 90.0 ±2% 1 Fault reporting, overvoltage

protection, undervoltage protection –40 to 85 8SOIC 0.50

TPS2594218 V, 5 A, 42 mΩ current limiting power MUX eFuse w/integrated reverse current protection, IMON & PG

2.7 to 18 5 42 ±8% 1

Current sense/monitor, fault reporting, overvoltage protection,

power good, reverse current protection, thermal shutdown,

undervoltage protection

–40 to 85 20WQFN 1.10

Industrial protocol supportMicroprocessor Microcontroller

AM1810 AM335x AM437x AM5xxx1

MSP430 MSP432 C2000 Tiva C RM4x TMS570PRUSS ICSS #1 ICSS #1 ICSS #2 ICSS #1 ICSS #2

Industrial ethernet

ProfiNetTM RT/IRT v2.3 - X X - X X - - - - - -

Ethernet I/PTM - X X - X X - - - - - -

EtherCATTM Slave - X X - X X - - X2 - - -

Powerlink - X X - X X - - - - - -

Sercos III - X X - X X - - - - - -

Position encoder feedback

EnDat 2.2 - - X X X X - - X - X X

HIPERFACE DSL - - X X X X - - - - - -BiSS-C - X X X X X - - X - -

SinCos - - X X X X - X X X X X

Industrial fieldbus

CANOpen - X X X X X - - X X X XProfibusTM Slave DP X X X X X X - - - - - -

Profibus Master DP - X X X X X - - - - - -

HART (4-20 mA) - - - - - - X - - - - -

IO-Link Slave - - - - - - X - - - - -

(1) Each ICSS can run any protocol listed below. Hence, any combination of protocols possible. (2) Over external ET1100


Communication module and PLC controllerIndustrial protocol support / Ethernet PHY / eFuses

http://www.ti.com/product/DP83848I

http://www.ti.com/product/DP83848K

http://www.ti.com/product/DP83867E

http://www.ti.com/product/DP83867IR

http://www.ti.com/product/DP83867IR

http://www.ti.com/product/DP83867IS

http://www.ti.com/product/TPS25921A


http://www.ti.com/product/TPS25942A

DC-DC regulators


VIN (Min)

(V)

VIN (Max)

(V)

VOUT (Min)

(V)

VOUT (Max)

(V) Iout (A) Topology

Switch Current

Limit (Typ) (A)

Iq (Typ) (mA)

Duty Cycle (Max) (%) Soft Start Compensation Special Features


Range (°C)

Pin/Package

Price* (US$)

TPS54218/318

2.95 V to 6 V input, 2/3 A synchronous step-down SWIFT™ converter

2.9 6 0.8 4.5 2/3 Buck 2.9/4 0.35 98 Adjustable ExternalEnable, frequency

synchronization, power good, tracking

–40 to 150 116/WQFN 1.40/1.80

TPS543204.5 V to 17 V input, 3 A synchronous step-down SWIFT converter

4.5 17 0.8 15 3 Buck 4.2 0.6 98 Adjustable InternalEnable, frequency

synchronization, power good, tracking

–40 to 150 14/VQFN 1.50

TPS6217528 Vin, 0.5 A step-down converter with DCS-Control™

4.75 28 1 6 0.5Buck,

synchronous buck

1 0.022 100 Adjustable InternalEnable, light load

efficiency, sleep mode, power good

–40 to 85 10/SON 0.70

TPS55340

Integrated, 5 A 40 V wide input range boost/SEPIC/flyback DC-DC converter

2.9 32 3 38 3 Boost, SEPIC, flyback 6 0.5 90 Adjustable External

Enable, frequency synchronization, power

good–40 to 125 14/HTSSOP,

16/WQFN 1.85

TPS54360/560

4.5 V to 60 V input 3.5 A / 5 A step-down DC-DC converter with Eco-mode™

4.5 60 0.8 58.8 3.5/5Buck,

inverting buck-boost

5.5/7.5 146 98 No External

Enable, frequency synchronization,

light load efficiency, adjustable UVLO

–40 to 125 8SO PowerPAD 2.30

TPS54361/561

4.5 V to 60 V input 3.5 A / 5 A step-down DC-DC converter with soft-start and Eco-mode

4.5 60 0.8 59 3.5/5 Buck 5.5/7.5 152 98 Adjustable External

Enable, frequency synchronization,

light load efficiency, power good, tracking,

adjustable UVLO

–40 to 125 0.88 3.00


Communication module and PLC controllerDCDC regulators / DDR termination regulators / PMICs / load switches

Power Management ICs (PMICs)

Part Number DescriptionMCU/processor

attached Vin (V)

# of Regulator Outputs

DC/DC Step-Up

Converter

DC/DC Step-Down Converter LDO Pin/ Package

Price* (US$)

TPS65217 PMIC w/ 3 DC/DCs, 4 LDOs, linear battery charger & white LED driver AM335x ZCE 2.7 to 5.8 7 1 3 4 48/VQFN 3.45

TPS65910 Integrated PMIC w/ 4 DC/DCs, 8 LDOs and RTC in 6x6mm QFN family AM335x 1.7 to 5.5 12 1 3 9 48/VQFN 2.75

TPS650250 PMIC for Li-Ion powered systems AM335x 1.5 to 6.6 6 - 3 3 32/VQFN 2.20

TPS65218 PMIC for ARM cortex-A8/A9 SoCs and FPGA AM437x AM335x 2.2 to 5.5 7 1 5 1 48/HTQFP

48/VQFN 3.45

Load switches

Part Number DescriptionVin (Max)

(V)Imax (A)

Ron (mΩ)

Leakage Current

(µA) (Typ) Channels Special FeaturesOperating Temp. (°C)

Pin/ Package

Price*(US$)

TPS22954 5.7 V, 5 A, 14 mΩ load switch with voltage monitoring and quick output discharge 0.7 to 5.7 5 14 34 1

Adjustable rise time, power good, quick

output discharge Vbias–40 to 105 10/WSON 0.36

TPS22968 5.5 V, 4 A, 25 mΩ, 2-channel load switch with quick output discharge and adjustable rise time 0.8 to 5.5 4 25 55 2

Adjustable rise time, quick output discharge

Vbias–40 to 85 14/WSON 0.36

TPS22960 5.5V, 0.5A, 435mΩ, 2-Channel Load Switch with Quick Output Discharge 1.62 to 5.5 0.5 435 0 2 Quick output discharge –40 to 85 8/SOT-23

8/UQFN 0.36

*Suggested resale price in U.S. dollars in quantities of 1,000. New products are listed in bold red

DDR termination regulators

Part Number DescriptionDDR Memory

Type

IOUT VTT

(Max) (A)

IOUT VTT

(Max) (A)

VIN (Max)

(V)Iq (Typ)

(mA) Output Additional FeaturesOperating Temp. (°C)

Pin/ Package

Price* (US$)

TPS51200 3 A sink/source DDR termination regulator with VTTREF buffered reference

DDR, DDR2, DDR3, DDR3L,

DDR4, LPDDR2, LPDDR3

3 1.1 3.5 0.5 VREFVTT Enable, power good –40 to 85 10/VSON 0.75

TPS53317 6 A, low input voltage synchronous step-down SWIFT™ converter

DDR, DDR2, DDR3, DDR3L,

DDR4, LPDDR2, LPDDR3

6 1 6 0.32 VTTOvervoltage, Over-

Temperature and Hiccup Undervoltage Protection

–40 to 85 20/VQFN 2.60
















DP8384810/100 MbpsEthernet PHY

10/100M/1G/10G

PHY

Texas Instruments is an industry leader in high performance clock and timing products. With an expansive portfolio of unique products, easy to use design tools, and worldwide support, TI helps engineers quickly design clock trees, simulate and verify performance.

Clock generators and XO replacement

Part NumberNumber of

Outputs Output Levels

Max Output Frequency in

MHz VCC Core (V) VCC Out (V) Programmability DividersJitter RMS


Price* (US$)

CDCE(L)913 3 LVCMOS 230 1.8 3.3/2.5/1.8 I2C, EEPROM, pin Fractional and integer > 1ps –40 to 85 14/TSSOP 1.6

CDCEL824 4 LVCMOS 201 1.8 1.8 I2C, EEPROM, pin Fractional and integer > 1ps –40 to 85 16/TSSOP 1.85


CDCE906 6 LVCMOS 167 1.8 3.3 I2C EEPROM, pin Fractional and integer > 1ps –40 to 85 20/TSSOP 2.2



CDCM6208 8 CML, HCSL, LVCMOS, LVDS, LVPECL 800 3.3/2.5/1.8 3.3/2.5/1.8 I2C, SPI, EEPROM, pin Fractional and integer 265 fs –40 to 85 48/VQFN 5.2

CDCE62002/5 2/5 LVPECL, LVDS, LVCMOS 1175 3.3 3.3 SPI, EEPROM integer 500 fs –40 to 85 32 or 48/VQFN 6.60 to 7.5

CDCM9102 2 HCSL 100 3.3 3.3 uWire, pin integer 500 fs –40 to 85 32/VQFN 2.25

LMK03328 8 CML, HCSL, LVCMOS, LVDS, LVPECL 1000 3.3 3.3/2.5/1.8 I2C, EEPROM, pin Fractional and integer 100 fs –40 to 85 48/WQFN 10

Clock fanout buffers

Part Number (Families*)Number of

Outputs Output Levels

Max Output Frequency in

(MHz) VCC Out (V) Operating Temperature Range (°C) Pin/Package Price* (US$)

CDCLVC11xx 2/4/6/8/10/12 LVCMOS 250 2.5/3.3 –40 to 85 8 to 24/TSSOP 0.90 to 2.60

CDCVLD12xx 4/8/10/12/16 LVDS 800 2.5 –40 to 85 16 to 48/VQFN 2.85 to 5.90

CDCLVP11xx 2/4/8/10 LVPECL 2000 to 3500 2.5/3.3 –40 to 85 16 to 32/VQFN 3.15 to 5.55

CDCV304 4 LVCMOS 200 2.5/3.3 –40 to 85 8/TSSOP 1.2

LMK0010x 5/10 LVCMOS 200 2.5/3.3 –40 to 85 24 or 32/WQFN 2.25 or 2.95

LMK0030x 4/6/10 LVPECL, LVDS, HCSL, LVCMOS 3100 2.5/3.3 –40 to 85 32 or 28/WQFN 3.35 to 5.25

LMK0033x 4/8 HCSL 400 2.5/3.3 –40 to 85 32 or 40/WQFN 1.20 or 1.80

CDCUN1208LP 8 LCMOS, LVDS, HCSL 400 1.8/2.5/3.3 32/VQFN 5

*) ‘x’ indicates family of devices


ClockingOverview / clock generators / clock fanout buffers

http://www.ti.com/product/CDCE913






http://www.ti.com/product/CDCEL824

http://www.ti.com/product/CDCLVC1102

http://www.ti.com/product/CDCLVP110

http://www.ti.com/product/CDCM6208

http://www.ti.com/product/CDCM9102

http://www.ti.com/product/CDCUN1208LP

http://www.ti.com/product/CDCV304

http://www.ti.com/product/LMK00101




Notes

_________________________________________________________________________________________

_________________________________________________________________________________________

_________________________________________________________________________________________

_________________________________________________________________________________________

_________________________________________________________________________________________

_________________________________________________________________________________________

_________________________________________________________________________________________

_________________________________________________________________________________________

_________________________________________________________________________________________

_________________________________________________________________________________________

_________________________________________________________________________________________

_________________________________________________________________________________________

_________________________________________________________________________________________

_________________________________________________________________________________________

_________________________________________________________________________________________

_________________________________________________________________________________________

_________________________________________________________________________________________

_________________________________________________________________________________________

_________________________________________________________________________________________

_________________________________________________________________________________________

_________________________________________________________________________________________

_________________________________________________________________________________________


SLYY041C© 2015 Texas Instruments Incorporated

The platform bar, C2000, DCS-Control, Delfino, E2E, MSP430, Piccolo, Sitara and Tiva are trademarks of Texas Instruments. All other trademarks are the property of their respective owners.

TI Worldwide Technical SupportInternetTI Semiconductor Product Information Center Home Pagesupport.ti.comTI E2E™ Community Home Pagee2e.ti.com

Product Information CentersAmericas Phone +1(512) 434-1560

Brazil Phone 0800-891-2616

Mexico Phone 0800-670-7544

Fax +1(972) 927-6377 Internet/Email support.ti.com/sc/pic/americas.htm

Europe, Middle East, and AfricaPhone

European Free Call 00800-ASK-TEXAS (00800 275 83927)

International +49 (0) 8161 80 2121

Russian Support +7 (4) 95 98 10 701

Note: The European Free Call (Toll Free) number is not active in all countries. If you have technical difficulty calling the free call number, please use the international number above.

Fax +(49) (0) 8161 80 2045Internet www.ti.com/asktexasDirect Email [email protected]

JapanFax International +81-3-3344-5317 Domestic 0120-81-0036Internet/Email International support.ti.com/sc/pic/japan.htm Domestic www.tij.co.jp/pic

AsiaPhone Toll-Free Number Note: Toll-free numbers may not support

mobile and IP phones. Australia 1-800-999-084 China 800-820-8682 Hong Kong 800-96-5941 India 000-800-100-8888 Indonesia 001-803-8861-1006 Korea 080-551-2804 Malaysia 1-800-80-3973 New Zealand 0800-446-934 Philippines 1-800-765-7404 Singapore 800-886-1028 Taiwan 0800-006800 Thailand 001-800-886-0010International +86-21-23073444Fax +86-21-23073686Email [email protected] or [email protected] support.ti.com/sc/pic/asia.htm

B021014

Important Notice: The products and services of Texas Instruments Incorporated and its subsidiaries described herein are sold subject to TI’s standard terms and conditions of sale. Customers are advised to obtain the most current and complete information about TI products and services before placing orders. TI assumes no liability for applications assistance, customer’s applications or product designs, software performance, or infringement of patents. The publication of information regarding any other company’s products or services does not constitute TI’s approval, warranty or endorsement thereof.

Engineering Industrial InnovationGet to market faster with TI’s Industrial System Solutions

• Grid Infrastructure• Smart Grid Communications

• Smart Utility Meters• Renewable Energy

ti.com/smartgrid

2015

Smart Grid & Energy Solutions Guide

www.ti.com/buildingAutomation 2015

Connected Sensors Building Automation Systems Guide

www.ti.com/automation

2015

Industrial Communication

Solution Guide

Industrial Automation Solutions

Learn more and see TI’s latest industrial automation solution guides

www.ti.com/automation

Download now!• Field transmitter & process control• Industrial communication• Human machine interface (HMI)• Industrial motor drives • Smart grid & energy

http://e2e.ti.com

http://e2e.ti.com

http://support.ti.com




http://support.ti.com/sc/pic/americas.htm

http://support.ti.com/sc/pic/asia.htm

http://support.ti.com/sc/pic/japan.htm

http://www.ti.com/asktexas

http://www.tij.co.jp/pic




IMPORTANT NOTICE

Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment.

TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily performed.

TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and

applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide

adequate design and operating safeguards.

TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information published by TI regarding thirdparty products or services does not constitute a license to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI.

Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions.

Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements.

Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safetyrelated requirements

concerning its products, and any use of TI components in its applications, notwithstanding any applicationsrelated information or support that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use of any TI components in safetycritical applications.

In some cases, TI components may be promoted specifically to facilitate safetyrelated applications. With such components, TI’s goal is to help enable customers to design and create their own endproduct solutions that meet applicable functional safety standards and requirements. Nonetheless, such components are subject to these terms.

No TI components are authorized for use in FDA Class III (or similar lifecritical medical equipment) unless authorized officers of the parties have executed a special agreement specifically governing such use.

Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components which have not been so designated is solely at the Buyer’s risk, and that Buyer is solely responsible for compliance with all legal and regulatory requirements in connection with such use.

TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of nondesignated products, TI will not be responsible for any failure to meet ISO/TS16949.

Products Applications Applications

Audio www.ti.com/audio Automotive and Transportation www.ti.com/automotiveAmplifiers amplifier.ti.com Communications and Telecom www.ti.com/communicationsData Converters dataconverter.ti.com Computers and Peripherals www.ti.com/computersDLP® Products & MEMS www.ti.com/dlp Consumer Electronics www.ti.com/consumer-appsDSP dsp.ti.com Energy and Lighting www.ti.com/energyClocks and Timers www.ti.com/clocks Industrial www.ti.com/industrialInterface interface.ti.com Medical www.ti.com/medicalLogic logic.ti.com Security www.ti.com/securityPower Mgmt power.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defenseMicrocontrollers microcontroller.ti.com Video and Imaging www.ti.com/videoRFID www.ti-rfid.comOMAP Applications Processors www.ti.com/omap TI E2E Community e2e.ti.comWireless Connectivity www.ti.com/wirelessconnectivity

http://amplifier.ti.com

http://dataconverter.ti.com

http://dsp.ti.com

http://e2e.ti.com

http://interface.ti.com

http://logic.ti.com

http://microcontroller.ti.com

http://power.ti.com

http://www.ti.com/audio

http://www.ti.com/automotive

http://www.ti.com/clocks

http://www.ti.com/communications

http://www.ti.com/computers

http://www.ti.com/consumer-apps

http://www.ti.com/dlp

http://www.ti.com/energy

http://www.ti.com/industrial

http://www.ti.com/medical

http://www.ti.com/omap

http://www.ti.com/security

http://www.ti.com/space-avionics-defense

http://www.ti.com/video

http://www.ti.com/wirelessconnectivity

http://www.ti-rfid.com

http://e2e.ti.com

http://power.ti.com

http://www.ti.com/automotive

Programmable Logic Control (PLC) Solutions Guide

Documents

Transcript of Programmable Logic Control (PLC) Solutions Guide