Kee Klamp® Safety Components Guide

Safety Components Guide

• DESIGNED TO SUIT BS EN 10255 (ISO 65) STEEL TUBES FROM SIZES 13.5mm TO 60.3mm

• GALVANISED TO BS EN ISO 1461 OR AVAILABLE WITH POLYESTER COATING IN ANY RAL COLOUR

• FLEXIBLE SOLUTIONS FOR ALL TYPES OF SAFETY BARRIERS AND STRUCTURES

• WIDEST PRODUCT RANGE AVAILABLE

Y O U ’ L L N E V E R B E B E T T E R P R O T E C T E D

KEE KLAMP is a registered trademark of Kee Safety Ltd. Whilst every effort has been made to ensure the accuracy of the information contained in this brochure Kee Safety Ltd. cannot be heldresponsible for any errors or omissions. Kee Safety Ltd. reserve the right to alter or withdraw products without prior notice. Kee Safety Ltd. accept no responsibility for any loss or damage arising from

improper use of their products. Copyright 2008 Kee Safety Ltd. All Rights Reserved

Kee Safety Limited1 Boulton RoadReadingRG2 0NHUnited Kingdom

Tel: +44 (0) 118 931 1022Fax: +44 (0) 118 931 1146

Email: [email protected]

TYPE95-8

PGRINTERNALSPIGOT

95

TYPE92-8

92

PGRELBOW

TYPE93-8

93

PGR TEE

TYPE90-8

PGR THREESOCKET TEE

90

TYPE91-8

PGR TWOSOCKETCROSS

91

TYPE99-299-399-499-5

99-699-799-899-9

HEX KEY

99

TYPE100-5100-6100-7

100-8100-9

PLASTIC SETSCREW CAPS

10098

TYPE105-6105-7

105-8105-9

105

HORIZONTALRAILINGBASE

115

TYPES115

PACKERPLATEFORTYPE 115

S115

SWIVEL TEE

114

TYPE114-2114-6

114-7114-8

TYPE115-6115-7

115-8

+/- 7°+/- 7° +/- 7° +/- 7°

PROFILEDOR FLATSHEETINGCLIP

Each fitting has a simple numerical code reference, which defines the typeof fitting and the pipe size, or sizes, it is designed to receive. The firstnumber, preceeding the dash (-) identifies the type of Kee Klamp fitting. Asingle digit, following the dash, defines pipe size. Two single digits afterthe dash indicate that the fitting is designed to receive two sizes of pipe.

Both sockets‘A’ and ‘B’

designed to acceptpipe size 8

10-8Examples:

45-76

Kee KlampFittingType 45

A

B

A

B


Socket ‘A’ designedto acceptpipe size 7

Socket ‘B’ designedto accept pipe size 6

CROSSOVERCOUPLING

145

TYPE145-7

Specifying Kee Klamp® Components

mm in2 13.5 8 1/4”

3 17.5 10 3/8”

4 21.3 15 1/2”

5 26.9 20 3/4”

6 33.7 25 1”7 42.4 32 1 1/4”

8 48.3 40 1 1/2”

9 60.3 50 2”

Kee Klamp Fittings Size Tube Diameter mm o/d Nominal Bore

TYPE89-789-8

TWO SOCKETANGLE CROSS

89

+/- 11°

EAVESFITTING

350

TYPE350-8

COVERFLANGE

118

TYPE121-7

TYPE118-8

CORNERCROSSOVER

121

SHEETINGCLIP

79

TYPE79-7

TYPE82-582-6

82-782-882-9

SINGLESIDED CLIP

81

TYPE81-581-6

81-781-881-9

DOUBLESIDED CLIP

82

TYPE83-583-6

83-783-8

83

PIN FITTING

TYPE84-584-6

84-784-884-9

MALLEABLEPLUG

84

TYPE86-786-8

ANGLETEE

86

ANGLEELBOW

87

TYPE88-788-8

TYPE87-787-8

THREESOCKETANGLE TEE

88

+/- 11° +/- 11° +/- 11°

RIDGEFITTING

351

TYPE351-8

RATCHET

TYPE98-598-698-7

98-898-9

OFFSETRAILINGBASE

265

TYPE265-7265-8

TYPE78-578-6

78-778-8

EYE FITTING

78

TYPEA10-7A10-8

SPLIT TEE

A10

TYPEA21-8

SPLITCORNERCROSS

A21

SPLITCROSS

A26

TYPEA35-8

TYPEA26-8

SPLIT TEECROSSOVER

A35

TYPEA12-8

45°SPLIT TEE

A12

TYPEA40-8

SPLIT 4SOCKETCROSS

A40

TYPEA45-7A45-8

SPLITCROSSOVER

A45

TYPE10-210-310-410-510-610-6510-67

10-710-7510-7610-7810-810-8710-910-98

SINGLESOCKET TEE

10

TYPE12-512-6

12-712-8

45° SINGLESOCKET TEE

12

STRAIGHTCOUPLING

14

TYPE14-414-514-6

14-714-814-9

TYPE15-415-515-6

15-715-815-9

90˚ ELBOW

15

TYPE17-517-617-7

17-817-9

CLAMP-ONCROSS OVER

17

TYPE19-519-619-7

*19-819-8519-9

ADJUSTABLESIDEOUTLET TEE

19

TYPE18-618-718-8

INTERNALCOUPLING

18

TYPE16-516-6

16-716-816-9

16

CLAMP-ONTEE

TYPE29-629-729-830°- 60°SINGLESOCKET TEE

29

30°- 45°ADJUSTABLECROSS

30

TYPE35-435-535-6

35-735-835-9

TYPE30-630-730-8

PALLETFLANGE

31

TYPE31-8

THREESOCKET CROSS

TYPE45-245-345-445-545-645-65

45-745-7645-845-8645-8745-945-98

CROSSOVER

45

COMBINATIONSOCKET TEE& CROSSOVER

46

TYPE46-446-546-6

46-746-846-9

TYPE40-440-540-6

40-740-840-9

40

FOUR SOCKETCROSS

SIDE OUT-LET ELBOW

20

TYPE20-420-520-6

20-720-820-9

TYPE21-421-521-6

21-721-821-9

90° SIDEOUTLET TEE

21

TYPE25-425-525-6

25-725-825-9

25

THREESOCKET TEE

TYPE27-627-7

**27-8

27

0°- 45°THREESOCKETCUSTOM TEE

TYPE26-426-526-6

26-726-826-8726-9

TWO SOCKETCROSS

26

TYPE28-628-7

**28-8

0°- 45°FOUR SOCKETCUSTOMCROSS

28

TYPEBC53-8

SWIVELELBOW

BC53

TYPEC51-555C51-666

C51-777C51-888C51-999

C51

DOUBLESWIVEL SOCKET

TYPEM52-5M52-6

M52-7M52-8

M52

MALE CORNERSWIVEL SOCKETMEMBER

TYPEC50-44C50-55C50-66

C50-77C50-88C50-99

SINGLESWIVELSOCKET

C50

TYPEM50-4M50-5M50-6

M50-7M50-8M50-9

MALE SINGLESOCKETMEMBER

M50

TYPEM51-5M51-6

M51-7M51-8M51-9

MALE DOUBLESWIVELSOCKETMEMBER

M51

TYPEF50-4F50-5F50-6

F50-7F50-8F50-9

FEMALESINGLE SOCKETMEMBER

F50

TYPEP50-8

OFFSET FLANGE

P50

TYPEP51-8

TWO OFFSETFLANGES

TYPEC52-555C52-666

C52-777C52-888

C52

CORNERSWIVEL SOCKET

TYPEMH50-6

MALE SINGLEHORIZONTALSOCKET

MH50

TYPEMH51-6

MALEDOUBLEHORIZONTALSOCKET

MH51

FLANGE

TYPE61-361-461-561-6

61-761-861-9

TYPE63-663-763-8

ANGLE BASEFLANGE

TYPE62-262-562-6

62-762-862-9

STANDARDRAILINGFLANGE

6362

TYPE64-664-764-8

STANDARDVERTICALRAILING BASE

TYPE65-6

6564

STANDARDHORIZONTALRAILING BASE

TYPE66-666-766-8

GROUNDSOCKET

66

6160

TYPE60-560-6

60-760-8

EXTRA HEAVYFLANGE

TYPE55-655-755-8OBTUSEANGLEELBOW

55

ACUTEANGLEELBOW

56

TYPE56-8

TYPEC58-5C58-6C58-7

C58-8C58-9

SWIVELFLANGE

C58

TYPEP57-8

CENTRALFLANGE

P57

35

TYPEM58

BASE PLATE

M58

TYPE68-668-768-8

WALLFLANGE

68

TYPE67-767-8

ANGLEFLANGE

67

TYPE71-671-771-8

WEATHER CAP

71

TYPE69-669-7

69-8

RAILING FLANGEWITH TOEBOARDADAPTOR

69

RAILSUPPORT

70

TYPE70-570-6

70-770-8

COLLAR

75

TYPE72-8

72

STAIR TREADSUPPORT

TYPE77-477-577-6

77-777-877-9

PLASTICPLUG

77

TYPE76-576-6

76-776-8

76

HOOK

Kee Klamp® Safety Components Guide

P58

DOUBLECENTRALFLANGE

TYPEP58-7

P51

TYPEP57E-7

ELONGATEDCENTRALFLANGE

P57E

* Normally used in pairs but sold and priced separately.** These Fittings require machining to customer specifications.

Kee Klamp® Safety Components Guide

TYPE75-475-575-6

75-775-8

TYPE59--559-659-7

59-859-9

59

SPIGOTFLANGE


• DESIGNED TO SUIT BS EN 10255 (ISO 65) STEEL TUBES FROM SIZES 13.5mm TO 60.3mm

• GALVANISED TO BS EN ISO 1461 OR AVAILABLE WITH POLYESTER COATING IN ANY RAL COLOUR

• FLEXIBLE SOLUTIONS FOR ALL TYPES OF SAFETY BARRIERS AND STRUCTURES

• WIDEST PRODUCT RANGE AVAILABLE


KEE KLAMP is a registered trademark of Kee Safety Ltd. Whilst every effort has been made to ensure the accuracy of the information contained in this brochure Kee Safety Ltd. cannot be heldresponsible for any errors or omissions. Kee Safety Ltd. reserve the right to alter or withdraw products without prior notice. Kee Safety Ltd. accept no responsibility for any loss or damage arising from

improper use of their products. Copyright 2008 Kee Safety Ltd. All Rights Reserved

Kee Safety Limited1 Boulton RoadReadingRG2 0NHUnited Kingdom

Tel: +44 (0) 118 931 1022Fax: +44 (0) 118 931 1146

Email: [email protected]

TYPE95-8

PGRINTERNALSPIGOT

95

TYPE92-8

92

PGRELBOW

TYPE93-8

93

PGR TEE

TYPE90-8

PGR THREESOCKET TEE

90

TYPE91-8

PGR TWOSOCKETCROSS

91

TYPE99-299-399-499-5

99-699-799-899-9

HEX KEY

99

TYPE100-5100-6100-7

100-8100-9

PLASTIC SETSCREW CAPS

10098

TYPE105-6105-7

105-8105-9

105

HORIZONTALRAILINGBASE

115

TYPES115

PACKERPLATEFORTYPE 115

S115

SWIVEL TEE

114

TYPE114-2114-6

114-7114-8

TYPE115-6115-7

115-8

+/- 7°+/- 7° +/- 7° +/- 7°

PROFILEDOR FLATSHEETINGCLIP

Each fitting has a simple numerical code reference, which defines the typeof fitting and the pipe size, or sizes, it is designed to receive. The firstnumber, preceeding the dash (-) identifies the type of Kee Klamp fitting. Asingle digit, following the dash, defines pipe size. Two single digits afterthe dash indicate that the fitting is designed to receive two sizes of pipe.

Both sockets‘A’ and ‘B’

designed to acceptpipe size 8

10-8Examples:

45-76


A

B

A

B


Socket ‘A’ designedto acceptpipe size 7

Socket ‘B’ designedto accept pipe size 6

CROSSOVERCOUPLING

145

TYPE145-7

Specifying Kee Klamp® Components

mm in2 13.5 8 1/4”

3 17.5 10 3/8”

4 21.3 15 1/2”

5 26.9 20 3/4”

6 33.7 25 1”7 42.4 32 1 1/4”

8 48.3 40 1 1/2”

9 60.3 50 2”

Kee Klamp Fittings Size Tube Diameter mm o/d Nominal Bore

TYPE89-789-8

TWO SOCKETANGLE CROSS

89

+/- 11°

EAVESFITTING

350

TYPE350-8

COVERFLANGE

118

TYPE121-7

TYPE118-8

CORNERCROSSOVER

121

SHEETINGCLIP

79

TYPE79-7

TYPE82-582-6

82-782-882-9

SINGLESIDED CLIP

81

TYPE81-581-6

81-781-881-9

DOUBLESIDED CLIP

82

TYPE83-583-6

83-783-8

83

PIN FITTING

TYPE84-584-6

84-784-884-9

MALLEABLEPLUG

84

TYPE86-786-8

ANGLETEE

86

ANGLEELBOW

87

TYPE88-788-8

TYPE87-787-8

THREESOCKETANGLE TEE

88

+/- 11° +/- 11° +/- 11°

RIDGEFITTING

351

TYPE351-8

RATCHET

TYPE98-598-698-7

98-898-9

OFFSETRAILINGBASE

265

TYPE265-7265-8

TYPE78-578-6

78-778-8

EYE FITTING

78


• HIGH CORROSION RESISTANCE • LIGHTWEIGHT VERSATILITY• NO WELDING, THREADING OR BOLTING REQUIRED

KEE LITE is a registered trademark of Kee Safety Limited. Whilst every effort has been made to ensure the accuracy of the information contained in this brochure Kee Safety Limited cannot be held responsible for any errors or omissions. Kee Safety Limited reserves the right to alter or withdraw products without prior notice. Kee Safety Ltd accepts no responsibility

for any loss or damage arising from improper use of their products. ©2012 Kee Safety Ltd. All Rights Reserved.

Kee Lite® Safety Components Guide


• KeeLiteFittingsaremadefromhighgradeAluminium Silicon Magnesium Alloy.• Recommendedsetscrewtorqueis39Nm.• Minimumsliploadcapacityonaluminiumtube: 7.56kN. (safety factor = 2 with tube having a minimum UTS of 275 N/mm²).• Largegrubscrewsaredesignedtoresist threadstripping• ThecorerangeofKeeLiteFittingshasundergone independent testing by TUV. Forcurrentdetailoftheapprovedfittingsgoto www.keesafety.co.uk

Eachfittinghasasimplecodereference,whichdefinesthetypeoffittingandthetubesize,orsizes,itisdesignedtoreceive.Thefirstpart,precedingthedash(-)identifiesthetypeofKeeLite®fitting.Adigit,followingthedash,definestubesize.

Specifying Kee Lite® FittingsExample:

L10-8

Kee Lite®

FittingType L10

All three sockets designed to accept

tubesize8

A A

A

Forhighlycorrosiveenvironments,stainlesssteelgrubscrewsareavailableatasmalladditionalcharge.Kee Lite aluminium fittings are designed to suit BS EN 755 tube.

GasketsBS6180:1999(specificationforguardrailinandaroundbuildings)statesthatwhen Aluminium comes into contact with concrete the aluminium surface should have at least 2 coats of Bituminous paint applied.

The simple alternative is to use a standard Kee Lite rubber gasket.

Kee Lite® Technical Information

LG58 LG61-8 LG62-8 LG68-8 LG70-6 LG148-9 LG152-7

LG61-6 LG62-6 LG68-6 LG69-7 LG70-7 LG150-8 LG152-8

LG61-7 LG62-7 LG68-7 LG69-8 LG70-8 LG152-6 LG164-8

Kee Lite®

Fitting Ref.Nom. Bore

mmTube Dia. 0.D. mm

Fitting I.D. mm

6 25 33.7 35

7 32 42.4 43.5

8 40 48.3 49.5

9 51 60.3 61.5

Kee Lite® Reference Chart

L148

TYPEL148-9/2L148-9/4(/2 & /4 refer to the number offixingholes)

HEAVY DUTY RECTANGULAR FLANGE

L152

TYPEL152-6L152-7L152-8

4 HOLE SQUARE FLANGE

L150

TYPEL150-8

HEAVY DUTY 4 HOLE SQUARE FLANGE

L160

TYPEL160-7L160-8

SMOOTH HANDRAIL FITTING

L164

TYPEL164-8

OFFSET WALL FLANGE

KL/SCG_v3/12_12

Kee Safety LimitedCradley Business ParkOverend RoadCradley HeathWest MidlandsB64 7DWUnited Kingdom

Tel:+44(0)1384632188Fax:+44(0)1384632192

Email:[email protected]

Kee Lite® Safety Components Guide Kee Lite® Safety Components Guide

L10

TYPEL10-6L10-7L10-8L10-9

SINGLE SOCKET TEE

L15

TYPEL15-6L15-7L15-8L15-9

90° ELBOW

L14

TYPEL14-6L14-7L14-8

STRAIGHT COUPLING

L19

TYPEL19-6L19-7L19-8

AJUSTABLE SIDE OUTLET TEE

L21

TYPEL21-6L21-7L21-8

90° SIDE OUTLET TEE

L20

TYPEL20-6L20-7L20-8

SIDE OUTLET ELBOW

L25

TYPEL25-6L25-7L25-8L25-9

THREE SOCKET TEE

L29

TYPEL29-7L29-8

30° TO 60° SINGLE SOCKET TEE

L26

TYPEL26-6L26-7L26-8L26-9

TWO SOCKET CROSS

L30

TYPEL30-7L30-8

30° TO 45° ADJUSTABLE CROSS

L45

TYPEL45-6L45-7L45-8

CROSSOVER

L35

TYPEL35-6

THREE SOCKET CROSS

L46

TYPEL46-6

COMBINATION SOCKET TEE AND CROSSOVER

LF50

TYPELF50-6LF50-7LF50-8

FEMALE SINGLE SWIVEL SOCKET MEMBER

LC50

TYPELC50-66LC50-77LC50-88

SINGLE SWIVEL SOCKET

LM50

TYPELM50-6LM50-7LM50-8

MALE SINGLE SWIVEL SOCKET MEMBER

LM51


MALE DOUBLE SWIVEL SOCKET MEMBER

LC51

TYPELC51-666LC51-777LC51-888

DOUBLE SWIVEL SOCKET

LC52

TYPELC52-666LC52-777LC52-888

90° CORNER SWIVEL SOCKET

LB54

TYPELB54-66LB54-77LB54-88

AJUSTABLE ELBOW

LM52


90° MALE CORNER SWIVEL SOCKET

LC58

TYPELC58-6LC58-7LC58-8

SWIVEL FLANGE

L61

TYPEL61-6L61-7L61-8

FLANGE

LM58

TYPELM58

BASE PLATE

L62

TYPEL62-6L62-7L62-8

STANDARD RAILING FLANGE

L69

TYPEL69-7L69-8

FLANGE WITH TOEBOARD ADAPTOR

L68

TYPEL68-6L68-7L68-8

WALL FLANGE

L70

TYPEL70-6L70-7L70-8

RAIL SUPPORT

L114

TYPEL114-6L114-7L114-8

SWIVEL TEE

L84

TYPEL84-6L84-7L84-8

PLUG

Kee Klamp® Safety Components Guide

Documents

Transcript of Kee Klamp® Safety Components Guide