IMT Orbit Catalogue - Innovative Measurement Technology Ltd.

DIGITAL NETWORK

[email protected]

Orbit digital measurement system

Higher performance does not meanhigher costs.

Quality standards in industry andresearch are becoming increasinglytight and demands for cost savings arealso increasing. The upgrade from Orbit2 to Orbit 3 provides the way forward forpresent and future precisionmeasurement or positioning needs,whether on the production line or in thelaboratory.

A system that incorporates morethan one sensor technology willnormally require different sets of signalconditioning electronics and software,with all the problems often associatedwith getting diverse technologies andsoftware to work together.

In recognition to the fact that there isnot a single sensor technology that issuitable for all gauging or positioningapplications, Orbit 3 is not dedicated toa single sensor technology and isdesigned for use with an extensiverange of third party sensors.

The upgrade to the Orbit 3 systemcarries forward all the well provenattributes of Orbit 2 plus essentialadditions to performance at no extracost. (See page 7)

Orbit 3 is still based on a ruggedand well proven RS485 multi-dropnetwork running at 1.5m Baud. Thisenables the very high data speedsrequired for dynamic applications.Special attention has been given to allaspects of screening against electricalinterference to provide good noiseimmunity (conforms to EN61000-6-2),which is essential to ensure reliabledata processing.

All Solartron Metrology sensors andmechanical interfaces have beenrigorously tested to ensure a long andproductive life which coupled withthe Orbit 3 data processing systemleads to less down time, improvedproductivity and lower costof ownership.

Displacementtransducers

Gaugingprobes

DIGITAL NETWORK

Miniprobe

PCI networkcard

EthernetinterfaceUSB

interface

RS232interface

Analogueinput

Digitalinput / output

Encoderinput

SI 7500controller

DR 600,DR 700

readouts

SI 3500controller

SI 1500controller

Controllers No. of devices Description

SI 1500 1 Single channel panel mount

display

SI 3500 2 Twin axis display / controller DR

600 / DR 700 Up to 30 Digital readout

SI 7500 Up to 16 Multi channel controller RS232

Interface Module Up to 100 Single channel serial interface

USB Interface Module Up to 31 Single channel serial interface

Ethernet Interface Module TBC Single channel serial interface

PCI network card Up to 200 instandard mode

Dual channel PCI card(up to 100 devices per channel)

Refer to page 14 for details

Leverprobe

Interface Modules Description

Encoder Input Interface to rotary and linear scale incremental encoders (TTL)

Digital I/O Interface to discrete switches and to provide switch outputs.8 I/O lines

Analogue Input Interface to physical sensors with a DC output or 4-20mA

Digimatic Input Interface to Digimatic capable gauges

Power Supply (not shown) Provides power to Orbit modules

Refer to page 15 for details

Software

Software for Microsoft Windows. This includes aCOM object library and DLLs. These allowinterfaces with modern development environments.Examples are also available in VBA.Microsoft® , Windows® 98, Windows® ME, Windows® 2000, Windows®

XP, Windows NT® , Excel® , VBA and VB are either registered trademarksor trademarks of Microsoft Corporation in the United States and/orother countries.

°C PA N

Flexure

Blockgauges

Digimaticinput

[email protected]

A universal truthData is only of true value when it is processed from a reliable source

Unerring data collection + Powerful processing = Rock solid results

3

Unerring data collectionA reliable sensor is essential to anydata processing system. All Orbitbased digital sensors and mechanicalinterfaces are designed to generatereliable data, not just from new but formillions of cycles.

Powerful processingGood original data can be ruined bynoisy signal conditioning and poorimmunity to electrical interference,which in turn affects the repeatabilityof results. Orbit 3 processes andtransmits clean, repeatable data fromsensors at speeds of up to 4,000readings per second.

Rock solid resultsData is only of use if it can be displayedand/or acted upon. Orbit 3 is availablewith a comprehensive range ofDisplay/Controllers or software driversand DLL’s for PC based systems.Ethernet modules will be added to theexisting PCI card, I/O and RS 232modules during 2010 to increasecommunication options to both PC’sand PLC’s.

All standardtransducer cablesfeaturea polyurethane(PUR) sheath witha foil screen layerfor better electricalscreening.Improvedmechanicalproperties includereduced ‘memory’effect and superiorresistance to scuffsand cuts

Anti rotation devicedesigned to bestrong yet givegood non repeatwith probe tip offcentre

Tight tolerancecartridge type

bearing withcarbon/chrome

balls providesgood non repeat

and long life (typetested to over 13m

cycles)

Titanium corecarrier: inert and

able to withstandlateral shock

A multi-chamberedcoil helps improveefficiency byincreasing the gainas the core movesalong the coil

Machined fromsolid, hardened

stainless steel(400 series)

Strong lightweight body withscreening againstelectricalinterference toEN61000-6-2

Strong lightweightconstructionholding the sensoraddress to enableHOT SWAP facility.Improved clampingand IP65 option

35mm DIN Railmount as standard.Removeable toenable alternativemounting options.

PIE (ProbeInterfaceElectronics)

T-Con Orbitnetworkconnector

Indicator lampsshow power withinlimits and datatransmission active

[email protected]

Specification/feature orbit 2 orbit 3Accuracy 0.1% of reading 0.05% to 0.07% of reading (depending on probe

type)

Hot Swap Capability N/A Smart T-Con enables fast exchange of probes

Modules into single PCI card1 62 200

Probe Fault Indication Happy Light Each PIE / Sensor (Red)

Low Supply Voltage Indication N/A Each PIE / Sensor (Red)

Data Transmission Indication Happy Light Each PIE / Sensor (Blue)

Weight 128g 88g max( Din Rail option)

Environmental Sealing (PIE / T-Con) IP43 IP43 / IP65 Optional

Din Rail Mount option N/A New T-Con design with DIN Rail (35mm) attachment

Ethernet Interface Module N/A Ethernet Communication Module to be available 2010

RS232 Interface Module 31 modules Improved to handle 100 modules

Encoder Input Module Standard / Dynamic As orbit2 + Dynamic Measurement Control

Clamping Arrangements Single Lever Mechanism Increased robustness of clamping assembly usingdouble-leverassembly for high vibration applications

Power Supply Modules Separate Block Arrangement New smaller versions including PIE DCvoltage versionconnected directly to stack

Compatibility with Instruments Solartron SI 1500, SI 3500, SI 7500, DR 600, DR 700

Measurement Ranges 1, 2, 5, 10, 20mm for Gauging sensors, 1mm to 300mm for Displacement sensors

Actuation Spring, Pneumatic, Feather Touch, Ultra-Feathertouch

Measurement Modes Standard, Dynamic, Buffered Standard, Dynamic, Buffered (included as standard)

Resolution User selectable <0.1µm

Mechanical Constructionof Electronics Modules

Die-cast Aluminium Nylon and ABS plastic

Electrical Immunity2 CE Marked CE Marked

Operating Temperature (PIE / T-Con) 0° to +60°C 0° to +60°C

Electrical / Software Compatibility Orbit 3 is completely electrically compatible with Orbit 2 and software

Mechanical Compatibility Orbit 3 is mechanically compatible with Orbit 2 when mounted at the start or end of the Orbit 2 stack

1 External power supplies required for >10 modules2 EN6100-6-3 and EN6100-6-2 (2005)

orbit 2 v orbit 3It just gets better and better...

[email protected]

Gauge probes: spring push

Standard - DP Compact - DZ

Contact Gauging probes very oftenprovide the only cost effectivesolution for a wide range ofmeasuring or positioningapplications in diverse industries.

As with all electromechanicaltransducers, life is of paramountimportance. It is not too difficult toproduce a Gauge Probe that performswell when new, it is considerably moredifficult to produce a probe thatmaintains its performance throughout along working life.

It requires close attention to detailin design and materials as well asconsiderable investment in state ofthe art machines to produce bearings,which are the heart of a gauge probe.

Solartron Metrology has completecontrol in house over all aspects for thedesign and manufacture of a widerange of linear bearing assemblies andsensors.

This is demonstrated very well in theDZ range, where a very short bodylength and increased performance hasbeen made possible due to a uniquesensor being mounted inside a specialbearing.

Whether the application is in thelaboratory or in a manufacturingenvironment, the extensive range ofgauge probes has somethingsuitable for a very wide range ofenvironments.

Customised or special products willalways be considered when there is notan exact fit in our standard productrange.

The Standard DP range of Spring PushProbes has justifiably become theworkhorse of the gauging industry. Veryhigh resolution, excellent linearity andhigh data speed come as standard.Long life precision bearings, and anIP65 rating ensure that probes maintaintheir performance for millions of cycles.

The DZ’s are probably the shortestprobes available on the market with afull 1mm or 2mm calibrated travel.A bearing size normally found only inmuch longer bodies ensures a longlife. The small size coupled toenhanced linearity and resolutionmake them ideal where space is aproblem.

Feather Touch - DTWith very low tip forces coupledwith user selectable options of highresolution and data speed, FeatherTouch Probes are ideal for the gaugingof delicate high precision components.Long life bearings ensure that theperformance of the probes aremaintained through millions of cycles inindustries producing high volumes ofcomponents on short cycle times.

5 [email protected]

Short or Narrow Body Standard

Axial cable outlet DZ/1/S DZ/2/S - DP/1/S D6P/2/S DP/2/S DP/5/S DP/10/S DP/20/S DP10/2/S Radial cable outlet

DZR/1/S DZR/2/S DP/0.5/S - - DPR/2/S - DPR/10/S DPR/20/S - Body

diameter 8h6 6h6 8h6

Measurement range (mm) 1 2 0.5 1 2 2 5 10 20 2 Pre-travel (mm) 0.15 0.15 0.03 0.15 0.15 0.15 0.15

0.15 0.15 0.15 Over travel (mm) 0.35 0.35 0.05 0.35 0.35 0.85 0.85 0.85 0.85 8.85 Accuracy (% of reading)1 0.05 0.05 0.05 0.05 0.05 0.05 0.05

0.06 0.07 0.05 Repeatability (µm) 0.15 0.15 0.1 0.15 0.15 <0.15

Tip Force (N) @ centre travel 0.7 ± 20% 0.7 ± 20%

Resolution (µm user selectable) <0.01 <0.01 <0.01 <0.01 <0.01 <0.01 <0.05 <0.05 <0.1 <0.01 Data speed (user selectable) Up to 3906

readings per second Up to 3906 readings per second Environmental Protection IP65 (Probe only) IP65

(Probe only)

Feather Touch

Axial cable outlet DT/2/S DT/5/S DT/10/S DT/20/S

DT10/2/S

Radial cable outlet DTR/2/S DTR/5/S DTR/10/S DTR/20/S -

Body diameter 8h6

Measurement range (mm) 2 5 10 20 2

Pre-travel (mm) 0.15 0.15 0.15 0.15

Over travel (mm) 0.85 0.85 0.85 0.85 8.85 Accuracy (% of reading)1 0.05 0.05 0.06 0.07

0.05 Repeatability (µm) <0.15

Tip Force (N) @ centre travel 0.3 ± 20%

Resolution (µm user selectable) <0.01 <0.05 <0.05 <0.1 <0.01

Data speed (user selectable) Up to 3906 readings per second

Environmental Protection IP50 (probe only)

1 Accuracy 1µm or % reading, whichever greater

Materials

Case Stainless steel

Probe tip Nylon or tungsten carbide

Gaiter High grade polymer(none on Feather Touch)

Cable 2m PUR

Temperature ranges (°C)

Storage: probe + signal conditioning -20 to +70

Operating: PIE / T-Con 0 to 60

Probe operating: (not Feather Touch) +5 to +80

Probe operating: (Feather Touch) -10 to +80

Also see...

Dimensions and drawings Page 24 u

Special probe tips Page 34 u

Electronics / instrumentation Page 18 u

Braided and armoured cableand special cable lengths areavailable on request

Digital Probe interface electronics

Bandwidth Up to 460Hz

Output Serial RS485 signal level, Solartron Orbit Protocol

Power ( VDC ) 5± [email protected], includes power for probe

IP Rating 43 ( 65 available on request )

Weight (grams) Probe interface electronics 52

T connector 36

DIN rail adaptor + T-Con 46

[email protected]

Gauge probes: pneumatic push

Standard range - DP ‘J’ Type - DJ

Pneumatic Probes are ideal for usein automatic gauging applicationsor for accessing details that wouldbe diffi cult or impossible to reachusing conventional spring pushprobes.

With no side loading at the contacttip, Pneumatic probes also ensureexcellent repeatability and long life.

Various component materials anddesigns are affected in different waysby the force applied at the pointof contact at the probe tip. Somematerials such as glass or plastic, forexample, require very low tip forces toavoid deforming the component andcontact tip materials that do not leavea mark. Other applications mayrequire higher tip forces.

The Standard range of PneumaticProbes comes with an IP65 rating toensure a long working life in wet oroily environments.In order to ensure the probe is totallysealed to IP65, actuation is achievedby pressurising the gaiter.

J’ Type probes are similar to StandardPneumatic Probes except thatactuation is by an inbuilt piston. Hightip forces are available but as air isvented through a port close to thefront of the probe, they have a lowerIP rating.

Feather Touch - DT Ultra Feather Touch - UTFeather Touch Probes are designedspecifically for applications where lowtip forces are critical.Air is vented through the shroud at thefront of the probe during actuation,which in turn cleans the bearing. With nogaiter to protect the shaft fromcontamination they are unsuitable foruse in wet or oily conditions.

Ultra Light probes are similar toFeather Touch probes except theyhave a significantly lower movingmass and are capable of tip forces aslow as 0.03N.

7 [email protected]

Standard ‘J’ Type

Axial cable outlet DP/2/P DP/5/P DP/10/P DP/20/P DP10/2P D6J/2/P DJ/2/P DJ/5/P DJ/10/P DJ10/2P

Radial cable outlet DPR/2/P DPR/5/P DPR/10/P DP/20/P DPR10/2/P - DJR/2/P DJR/5/P DJR/10/P DJR10/2/P

Body diameter 8h6 6H6 8h6

Measurement range (mm) 2 5 10 20 2 2 2 5 10 2

Pre-travel (mm) 0.15 0.15 0.15 0.15 0.15 0.15 Over travel

(mm) 0.85 0.85 8.85 0.35 0.85 8.85 Accuracy (% of reading)1 0.05 0.05

0.06 0.07 0.05 0.05 0.05 0.05 0.06 0.06 Repeatability (µm)

0.15 0.15

Tip Force (N) @ centre travel± 20%

0.8 @ 0.4Bar, 2.8@ 1 Bar

0.85 @ 0.4Bar, 2.8 @

1 Bar

0.7 @ 0.4 Bar, 2.5 @ 1 Bar 1.15@1bar 0.85 @ 1Bar ± 20%

Resolution (µm user selectable) <0.01 <0.05 <0.05 <0.1 <0.01 <0.01 <0.01 <0.05 <0.05 <0.05 Data speed (user selectable) Up to 3906

readings per second Up to 3906 readings per second Environmental Protection IP65 (probe only) IP50

(probe only)

Feather TouchUltra

FeatherTouch

Axial cable outlet DT/2/P DT/5P DT/10/P DT/20P

Radial cable outlet DTR/2/P DTR/5/P DTR/10/P DTR/20/P

Body diameter 8h6 8h6

Measurement range (mm) 2 5 10 20 10 Pre-

travel (mm) 0.15 0.15

Over travel (mm) 0.85 0.85

Accuracy (% of reading)1 0.05 0.05 0.06 0.07 0.06 Repeatability (µm) 0.15

0.15 Tip Force (N) @ centre travel 0.18 @

0.3 Bar, 1.1 @ 1 Bar ± 30% 0.03 - 0.05@ 0.4 bar

Resolution (µm user selectable) <0.01 <0.05 <0.05 <0.1 <0.01

Data speed (user selectable) Up to 3906 readings per second

Environmental Protection IP50 (probe only)

1 Accuracy 1µm or % reading, whichever greater

Materials

Case Stainless steel

Probe tip Nylon or tungsten carbide

Gaiter High grade polymer(none on Feather Touch)

Cable 2m PUR


Storage: probe + signal conditioning -20 to +70

Operating: PIE / T-Con 0 to 60

Probe operating: (not Feather Touch) +5 to +80

Probe 0perating: (Feather Touch) -10 to +80

Also see...




Braided and armoured cableand special cable lengths areavailable on request



Output Serial RS485signal level, Solartron Orbit Protocol



Weight (grams) Probe interface electronics 52

T connector 36

DIN rail adaptor + T-Con 46

[email protected]

Specialist gauging products

Lever probe - DLLever probes are generally used forprecision gauging of components,such as shafts, for profiling but theOrbit compatible Lever Probe is notrestricted to such applications.The narrow body (compared to suchdevices based on dial test indictors)coupled with a gentle touch down to0.05N enables access to difficult toreach details, even on fragilecomponents.

Specialist gauging products are forapplications where a standard pencilstyle probe for various reasonswon’t fi t.

They are primarily motion changers ormechanical interfaces that sit betweenthe component and measuring sensor.

Special care has to be applied inthe design and manufacture of allmechanical interfaces where thecontact point is not in line with or maybe some distance from the sensor.

Unmeasured movement that is oftenseen for example in classic bell armlever type motion changers, is a majorcause of poor gauge R&R.

All specialist gauging products arespecifically designed to ensure longlife and consistent repeatability.

Block Gauges have precision linearbearings with zero clearance whichlimits unmeasured movement andtherefore maintains good repeatability,even when the contact tip is mountedoff centre.

Flexures have no sliding componentswithin the gauge frame and nocontacting moving components withinthe sensor. This means that millions ofcycles are achievable withoutdegradation of performance.

The miniature flexures within MiniProbes are particularly robust on bothaxes of loading.

9

Mini probe - DMThe Mini Probe is a very robustminiature flexure with all the attributesof its bigger brother.It’s particularly useful in all aspects ofbore gauging where high accuracyand durability are required.A range of customer fit contact tipsare available to suit most gaugingapplications.

Flexure - DUFlexures are ideal for very high volumeand high precision applications suchas bearing component gauging. Theyare often the best solution formeasuring moving material, suchas roundness testing, with Orbit set tovery high resolution and fast datatransmission.

Block gauge - DKBlock Gauges make precisionmeasurements of bores and cavities asimple and reliable process. A rangeof springs is available to ensure thattip forces can be maintained with theBlock gauge mounted in any attitude.Pneumatic actuators can be retrofittedfor automatic applications.

[email protected]

Block Gauge

Axial cable outlet DK/2 DK/5 DK/10

Radial cable outlet DKR/2 DKR/5 DKR/10

Measurement range (mm) 2 5 10

Total mechanical travel (mm) 3 6 11

Accuracy (% of reading)1 0.05 0.05 0.08

Repeatability (µm) @0.7 N tip force 0.25 0.25 0.5 Tip

force (N) at centre of travel (horiz. attitude) ± 20% 1.5 1.5 1.5

Mass of moving parts (g) less tool holder 35 90 95

Temperature coefficient (µm/°C) ± 0.2 ± 0.5 ± 1.0

Environmental protection IP65

Tip force is affected by mounting attitude and weight of accessories. Tip force can beadjusted higher or lower using a selection of springs. Tip force depends on the weight ofaccessories + the selected springs + air pressure. See page 28 for tool and tip holders,springs and pneumatic actuators.

Flexure Gauge

Axial cable outlet

DU/2/S

Radial cable outlet

DU/2/R

Measurement range (mm) 2

Total mechanical travel (mm) 2.5

Accuracy (% of reading)1 0.05

Repeatability (µm) @0.7 N tip force 0.1

Tip force (N) at centre of travel (horiz. attitude) 1.5

Environmental protection IP65

Mini Probe DM/0.5/S

DM/1.0/S

Measurment range (mm) 0.5 1

Accuracy (% of reading)1 0.20 0.2

Repeatability (µm)...at 100µ from limit stop...at 250µ from limit stop ...at500µ from limit stop ...at1000µ from limit stop

on axis0.10.250.5-

cross axis0.1

0.15 0.25-

on axis0.1-

0.150.3

cross axis0.1-

0.10.15

Tip force (at centre of range) (N) 0.7 ±

25%

Temperature coefficient (µm/°C) 0.08

Tip adjustment (mm) ± 0.25 from the factory position. Refer to manual

Mounting 1x M3 hex head screw (supplied)

Lever Probe

Measurement range (mm) 0.5

Mechanical travel (mm) 0.6

Stylus adjustment

180º

Accuracy (% of reading)1 0.2

Repeatability (µm) (on axis) <0.15

Hysteresis (µm) <0.25

Tip force (N) in 0.05N increments 0.05 - 0.3

Temperature coefficient 0.1µm/ºC

Materials

Body / frame Stainless steel (not mini probe)

Probe tip various options

Gaiter High grade polymer(not lever probe)

Cable 2m PUR (not mini probe - see P29)

Also see...






Output Serial RS485 signal level, Solartron Orbit Protocol



Weight (grams) Probe interface electronicsT connectorDIN rail adaptor + connector

523646


Storage (all) -20 to

+70

Operating (all) 5 to 60

[email protected]

Controllers

PCI Network card USB InterfaceModule (USBIM)

RS232 InterfaceModule (RS232IM)

Ethernet InterfaceModule (ETHIM)

Computer Interface

Bus PCI USB 2.0 full speed RS232 (up to 115.2 kB) Ethernet

Operating system Microsoft Windows

Network Interface

Signal RS485

Protocol Orbit

Number of Orbit modules(with external PSIM)1 Up to 100 Up to 31 Up to 100

To be confirmedNumber of Orbit modules withoutexternal PSIM)2

Up to 10 depending onmodule type

Up to 4 depending onmodule type 0

Baud Rate 187.5kB or 1.5MB 187.5kB

Measurement Modes supported3 All modes Standard/Buffered

Power Requirement

Voltage Range (VDC) 4.7 to 5.25To be confirmed

No Load Current (mA) 250 250 62

Environmental

Operating Temp. Range (°C) 0 to +60

To be confirmedStorage Temp. Range (°C) -20 to +85

IP Rating - 43

Mechanical & Connections

Computer connections PCI card slot USB socket type A RS232 port Ethernet port

Dimensions (mm) - 65 x 61 x 18 excluding connector (refer to PIE drawings on page 30)

Weight (g) 89 98g max( Din Rail option)

Material - Nylon and ABS plastic

1 1 PSIM required per channel.2 The specifications quoted are dependant on the power available from the computer in use.3 Orbit provides three measurement modes. Standard where modules are communicated with on an individual basis. Each module is asked for itsmeasurement data by the controller as required. Buffered where modules are told by the controller to take a series of measurements and store them ininternal module memory. This data is then extracted in one block by the controller when the required measurements have been taken. Dynamic wheremodules take measurements on receipt of a common synchronization pulse sent to the modules from the controller. Each module in turn sends its databack to the controller within a specific time frame. This process continues until the required number of measurements have been taken.

Whether it be PC, laptop or PLC,there is a range of plug-and-gointerfaces for directly connecting anOrbit network to the controller ofyour choice.

11

[email protected]

[email protected]

Modules

Digimatic inputModule (DIM)

Analogue InputModule (AIM)

Encoder InputModule (EIM)

Digital input-outputModule (DIOM)

Power Requirement

Voltage Range (VDC) 5 ± 0.25

Current Consumption1 (mA) 41 Up to 154 dependingon input type 49 42 (no load)

Signal Input 2

Input Type Digimatic Interface Analogue Voltage orCurrent Incremental Encoder 8 channel Input/Output

Input Voltage (VDC) - 0-24, 0-10, 0-5, ± 10, ± 5 30 max 0 to 30 Input

Currents (mA) - 4-20, ± 20, 0-20 < 10 1 per

Channel

Options - Special PT100 moduleavailable

Single ended ordifferential, HTL -

Signal Output

Voltage Output - - Open drain up to 30 V

Current Output - - 50 mA for each output

Reading Speed - Up to 3906 readings/second

Interpolation Rate - - x1, x2, x4 programmable -

Measurements performance

Warm-up - 95% accuracy after 5 mins - -

Linearity (%FSO) - 0.05

Bandwidth - 460 Hz 1.2 MHz max frequency DC

Measurement Modes Standard Standard/Dynamic/Buffered Standard/Dynamic

Standard/Dynamic

Environmental

Operating Temp. Range (°C) 0 to +60

Storage Temp. Range (°C) -20 to +85

IP Rating 43

Mechanical & Connections

Transducer Various connector options

Enclosure - Size (mm) 65 x 61 x 18 excluding connector (refer to PIE drawings on page 30)

Weight (g) 160

Material Nylon and ABS plastic

There is a range of modules for thirdparty sensors and for generalinstrumentation tasks.

The Analogue Input Moduleintegrates third party transducers (e.g.temperature, force, pressure) to theOrbit network. The Digital Input/ Output

module enables switches or controllines and the Encoder Input Moduleties in rotary or line scale incrementaltype encoders (TTL).

[email protected]

Accessories

Also see...


PSIM-AC PSIM-DC PSIM-5V

Output voltage 5.1VDC @ 1.8A

max.

Operating temp. range (°C) 0 to +60

Drive capability Up to 31 Orbit modules dependent on type

Supply voltage 90 to 264VAC@ 1 Amax.

10 to 30VDC 0 to 30

Supply frequency (Hz) 47 to 440 - -

Termination IEC320 plug (suppliedwith 2m lead andlocal AC supply

connector)

2m flying lead5m flying lead

(input directly to themodule. There is no

transformer)

Cable length (m) 2 (between module and power supply) -

Dimensions As PIE plus T-CON (see page 30). Module does not separate

PSIM (Power SupplyInterface Module)For use with multi-channel systemsneeding more power than availablefrom the host computer. The powersupply can also extend the networkbeyond the normal 10m per port limitdepending on cable type.

PSIM Transformer (not shown)

For use with Power Supply InterfaceModule versions PSIM-AC.

Other accessories avaliable includehigh perfomance data cables to ensurehigh speed orbit communication.

13

PSIM dimensions areidentical to PIE plusT-Con, however theunit does not separate

PIE (Probe InterfaceElectronics)Fitted to all Orbit products

T-Con connectorThe Orbit Network ‘building block’

35mm DIN rail connectorSupplied as standard

[email protected]

14

Software

Orbit® support packfor Windows®

Solartron Metrology provides softwaresupport for Microsoft Windows.This software is supplied with the OrbitNetwork Card, the USB InterfaceModule and the RS232 InterfaceModule.The Orbit Windows Support Packsoftware includes a COM ObjectLibrary for COM applications andDynamic Link Libraries (DLLs) forlower level programming. Support isalso provided for all majorprogramming languages, such asVBA, VB, C++, Borland C Builderand Delphi. Example programs forthese languages are available uponrequest.

Orbit® support packfor Excel®

The Orbit Excel Support Pack enablesthe user to take readings from theOrbit Network and place valuesdirectly into cells of a Microsoft Excelspreadsheet.Following installation of the Excelsupport pack, a toolbar becomesavailable to the user and enablescommands such as "Take Readings","Zero Readings", "Close Link", etc.,The Orbit Excel Support Pack disccontains examples to help you getstarted, each designed to showdifferent aspects of the software.

Orbit® examplesfor LabVIEW®

Solartron Metrology provides programexamples to enable users to developapplications under the NationalInstruments LabVIEW environment.Examples are also provided to allowquick test application tests, such astaking measurement readings fromDigital Probes or Linear Encoders intoLabVIEW.

Microsoft® , Windows® 98, Windows® ME, Windows®

2000, Windows® XP, Windows NT® , Excel® , VBA andVB are either registered trademarks or trademarks ofMicrosoft Corporation in the United States and/or othercountries.

Delphi® , C++ Builder® are registered trademarks ofBorland Software Corporation.

LabVIEW® is a registered trademark of NationalInstruments.

Orbit® is a registered trademark of Solartron Metrology.

DIGITAL NETWORK

Compatible with Windows XP, Vista,Windows 7 32 bit. Check with yourlocal sales office for 64 bit compatibility

[email protected]

Dimensions

Case size (incl. bezel) H = 48mm x W = 96 x D = 137mm

Panel cut out H = 44.5mm x W 93mm

Depth behind panel (inc. terminals) 135mm

Display

Display Type 7 digit red led

Display Update Rate Up to 10 readings/second

Indicators Low, OK and High warning lamps

Range -99.9999 to +99.9999

Resolution 1mm to 0.1um (user selectable)

Bandwidth/response time/sensor reading rate

Up to 100 readings/second

Discrete Inputs Zero, Peak(+Peak/-Peak/Difference), Hold

Outputs

Analogue 4-20 mA, -5V to +5V, -10V to +10V,0V to +5V, 0V to +10V (selectable)

Discrete Alarm Relay - Open Collector

Low, OK and High

Relay Response Time = 0.1-9.9 seconds (selectable)

Communications

Serial Port RS232 or RS485 Configurable

Power

Voltage +24 VDC

Current 850 mA Max

Environmental

Operating Temperature 10°C to 40°C

Storage Temperature -10°C to 70°C

Electrical Immunity EN6100-6-2:2007

Electrical Emissions EN61000-6-3:2007

Front Panel Sealing IP65

SI 1500Panel mount display / controller

u Red 7 digit display

u RS232 or RS485 Serial outputs

u VDC or 4-20 mA outputs

u Low, OK, High lamps and relays

u Peak Hold

The SI 1500 is a cost effectiveyet versatile panel mount singlechannel display specificallydesigned for use with Solartron’shigh performance Orbit® basedDigital Probes, Linear Encoders andModules.

15 [email protected]

u Intuitive menu

u 2 channel 7 digit colour displays

u 2 channel analogue colour displays

u Auto colour change for in/out range

u Auto course/fine resolution

u Peak hold facility

u Data logging facility

u RS232 output

u Discrete I/O

u 4-20mA or DC output

Specifically designed for use with highperformance Orbit® network, the SI 3500features an intuitive, menu driven-twinaxis display which can be programmedto display readings, set Limits/Alarms,Peak Hold, Track, or act as a DataLogger for inputs from one or twotransducers.

LCD Display

Digital 2 x colour

Analogue 2 x colour horizontal bars

Update speed 40Hz

Display length (mm) ± xx.xxxxx (user selectable)

Display length (ins) ± x.xxxxxx (user selectable)

Resolution mm Down to 0.05µm (user selectable)

Resolution ins Down to 0.000005'' (user selectable)

Keypad

Membrane type with 9 keys Print, Zero, Up, Down, Left, Right, Enter,Peak Hold/Track, Menu

Measurement type A, B, A+B, A-B, (A+B/2), (A-B/2), (B-A/a) X and Y Data

Logging 10,000 readings via switch or 1ms to 24hr time interval

Indications mm/inch, Lower & Upper Limits, Out of Range,Measurement Mode

Power requirement +24 VDC ± 10%

External I/O

Serial RS232 serial port (for printer or PC)

Discrete Output 2 x 3 isolated

Analogue Output 2 channels DC or 4-20mA

Environmental

Front Panel IP65

Case IP51

Rear connection IP51

EMC Immunity: EN6100-6-2:2001Emissions: EN61000-6-3:2001

Storage Temperature (°C) -20 to +50

Operating Temperature (°C) 0 to +50

Mechanical

Mounting Bench top or panel mount

Dimensions WxHxD (mm) Without bezel 134 x 65x160With bezel 144 x 74 x 175

SI 3500Twin axis display / controller

[email protected]

DR600 DR700

Display Type 24 character alpha numeric display

Display length ± 999.9999mm or ± 39.370078”

Resolution Down to 0.05µm or 0.000005”

Range Lamps Indicates Hi/OK/Lo for limited detection

Input

Number of Orbit modules up to 10 without external PSIMexampleup to 30 with external PSIM example

External input/output

Single output ù ùDigital I/O ù ùMotor drive ù ùMeasurement configurations

Individual probe ù ùProbe pair ù ùMultiple probes ù ùScan ù øGauging mode ø ùElectrical

Power supply (VAC) 96 to 244

Line frequency (Hz) 47 to 440

Environmental

Storage temperature range (°C) -20 to + 60

Operating temperature range (°C) 0 to +40 Humidity

0 to 95% non

condensing

Safety rating EN61010-1

EMC Emission: EN50081-1 Immunity:

EN50082-2

IP rating Front panel: IP65 Unit: IP40

Mechanical

Dimensions (mm) 235 x 190 x

90

Weight (kg) 2.25

DR 600 and DR 700Digital readouts

Designed specifically for use with Orbit,the DR 600 and 700 have a 24 characteralphanumeric display which guides theuser through a series of menus frominitial setup to gauging applications andarithmetic operations.

Both DRs have functions:

u Zero

u Print

u Motor Drive

u Program Select

u Units

u Preset

u Maximum/Minimum

u Limits/Tolerance

u Multiple Probes

u Probe Scan

u Mathematics

u Resolution

u Count Direction

u Reference Mark

u Display Freeze

u Lock

The DR 700 also has:

u Scaling Factor

u Max A + Max B

u Gauging Mode

u Autosense Mode

u Peak Mode


u Up to 16 digital probes / modules

u Up to 100 parts storable

u SPC support

u Suite of mathematical functions

u Intuitive menu system

u Clear graphical display

The SI 7500 is a multi axis metrologydisplay that connects to an OrbitNetwork and accepts up to 16 OrbitModule inputs; such as Digital Probes,Linear Encoders and Analogue InputModules.It features intuitive displays, helpfulaudio cues and user defi ned formulas.The SI 7500 also reports dynamicMin/Max measurements, provides SPCanalysis from an integrated databaseand offers connectivity to PC’s andother peripherals.

SI 7500

Display type 6'' Colour LCD

Resolution 0.0001mm or

0.000004''

Inputs

Signal Input Orbit

Connection type Orbit Network

Cable

Number of Orbit Modules 16

Additional Input/Outputs Remote Switch, USB Port, Remote Keypad, Parallel Data Port,RS232C Serial Port, Relay Outputs x 2

Electrical Interface

Power Supply (VAC) 85 to 264

Line Frequency (Hz) 43 to 63

Environmental

Storage Temperature (°C) -20 to +60

Operating Temperature (°C) 0 to +45

Humidity 0 to 95%, non condensing

Safety Rating EN 61010-1

EMC EN 55011:1998, EN50082-

2:1995

Mechanical

Enclosure WxHxD (mm) 292.1 x 190.5 x 69.85

Base WxHxD (mm) 254 x 50.8 x 190.5

Enclosure Weight (Kg) 1.59

Base Weight (Kg) 3.18

SI 7500Multi channel controller

[email protected]

Application examples

19

Synchronising data

Linear and Angular readings accurately synchronised using an Orbit RotaryEncoder Module and data from linear measuring sensors taken at highspeed with the Orbit Network set in Dynamic Mode.

Orbit multiple sensor technology

Gauging components, such as automotive pistons and con’ rods, withtemperature compensation and weight measurement within the samemeasuring station. Orbit can also accept strain and pressure sensors whererequired. See pages 4 and 15.

Inside diameter gauging

Dynamic Bore Gauging using Mini Probes with Orbit set in Dynamic Modeand resolution set to 0.1µm. See page 12.

Outside diameter gauging

2 probes configured A+B/2 is a common method used to measurediameters. If the centre line of the ball in a ball tip is not perfectly aligned tothe centre line of the component, errors can occur. The type of tip chosenfor a gauging application can have a significant effect on accuracy. A tipwith a knife edge or pin is often a better solution in this type of application.For a selection of tips, see page 34.

Automatic gauging systems

Automatic on line or post process is made possible with pneumatic probesand mechanical Interfaces. See pages 10 and 12.

Measuring angles

The precision measurement of angles requires high resolution + excellentlinearity and repeatability.

OrbitRotaryEncoderModule

a),b) gauge probes c)load celld) temperature sensor

Pneumaticallyoperatedgauging

a

b

c

d

a

b

c

d

Rotary encoder

Linear and Angularreadings poorlysynchronised and datataken at low speed

d

c

ba

On Axis

Cross Axis

[email protected]

20

Application examples

Con’ Rod weight grading

By using the Orbit system to balance sets of automotive connecting rods,the customer is able to use the same software as the dimensional gaugingsystem. A significant cost reduction can be achieved by reducing thenumber of sensor signal processing systems and the associated software.

Temperature and pressure

Research into the temperature and air pressure in automotive heating andair conditioning systems is made easy with Orbit Analogue Input Modulesand the Excel® support pack.

Daisy chain pressure sensors Measuring the change of the shape of a structure

Measuring the change of the shape of a structure and its recovery after beingstressed is a common problem. The Orbit multi drop data acquisition systemcan take readings from a mix of Displacement, Strain, Pressure andTemperature sensors.

Mechanical interfaces

Flexures have the best overall performance for contact measurementof moving material. Linear forces through the flexure and no slidingcomponents within the flexure help to ensure excellent performance and avery long life. See page 12.

Low tip forces

Tip force is critical when gaugingfragile or flexible components.

For low and very low tip forceprobes and special tips, seepages 8 and 10.

Linear forces

Load cell

AnalogueInputModule

To dimensionalgauging system

To control or dataacquisition system

Data

Force, temperature and pressure measurement

[email protected]

Dimensions (mm): Spring push gauge probes

DP/2/S DP10/2/S DP/5/S DP/10/S DP/20/S

A 47.50 75.00 66.50 90.50 127.00 C

2.00 4.00 2.00 2.00 3.00

B1 13.90 25.40 17.40 25.40 44.90

B2 10.90 14.40 11.40 14.40 23.90

DT/2/S DT/5/S DT/10/S DT/20/S

A 47.50 66.50 90.50 127.00 C 2.00 2.00 2.00 3.00

B1 13.90 17.40 25.40 33.90

B2 10.90 11.40 14.40 12.90

DP/2/V DP/5/V DP/10/V DP/20/V

A 46.00 65.00 96.00 127.00 C 2.00 2.00 2.00 3.00

B1 13.90 17.40 25.40 44.90

B2 10.90 11.40 14.40 23.90

DTR/2/S DTR/5/S DTR/10/S DTR/20/S

A 33.50 52.50 76.50 113.50 C 2.00 2.00 2.00 3.00

B1 13.90 17.40 25.40 33.90

B2 10.90 11.40 14.40 12.90

Standard Spring Push (DP/S)

Feather Touch Spring Push (DT/S)

Vacuum Retract (DP/V)

Right Angle Feather Touch Spring Push (DTR/S)

A1.00

Ø 3.

50

Ø 8h

6

B1

C

FULLY EXTENDED

FULLY RETRACTEDB2

30.00

A

30.00

1.00

Ø 3.

50

Ø 8h

6C

FULLY RETRACTED

FULLY EXTENDEDB1

B2

A

Ø 8h

6C

FULLY RETRACTED

FULLY EXTENDEDB1

B2

9.50

21.5

0

Ø 4.30

A

Ø 8h

6

B1

C

4.50

Ø 3.

50

Ø 3.

00

7.50

FULLY EXTENDED

FULLY RETRACTEDB2

8.00

30.0

0

8.50

Right Angle Standard Spring Push (DP/R)Plastic adaptor kit turns cable through 90° where axial space is limited.


Dimensions (mm): Spring push gauge probes

4.00 FULLY RETRACTED

FULLY EXTENDED15.00

Ø 3.

50

3.00 5.50

Ø 8h

6

6.50 FULLY EXTENDED

FULLY RETRACTED4.00

15.50

8.00

Ø 3.50

14.0

0

Ø 8h

6


FULLY EXTENDED

8.00

Ø 3.50

11.00

14.0

0

5.50

Ø 8h

6

FULLY EXTENDED

FULLY RETRACTED4.00

19.50

Ø 3.

50

3.00 6.50

Ø 8h

6

Compact Spring Push (DZ/S)Right Angle Compact Spring Push (DZR/S)

Ultra Small Spring Push (DP/0.5/S)

Ultra Short Spring Push (DP1/S)

Slim 6mm Ø Spring Push (D6P/2/S)

50.001.00

Ø 3.

50

Ø 6h

6

14.35 FULLY EXTENDED


DZ/S

DZ/S

DZ/S

DZ/S

22.505.30

Ø 3.

50

Ø 8h

6

7.45 FULLY EXTENDED


Ø 3.50

9.50 12.00Ø

8h6

3.78

9.50

8.00

FULLY EXTENDED

FULLY RETRACTED3.20

[email protected]

Dimensions (mm): Pneumatic push gauge probes

DP/2/PE DP/2/P DP/5/P DP/10/P DP/20/P

A 84.00 52.50 71.00 96.00 127.00 C 2.00 2.00 2.00 2.00 3.00

B1 25.40 13.90 17.40 25.40 44.90

B2 14.40 10.90 11.40 14.40 23.90

B1

C7.50

4.50

Ø 3.

50

A

Ø 8h

6

Ø 3.

00

FULLY EXTENDED

FULLY RETRACTEDB2

C

A

Ø 8h

6

B1 FULLY EXTENDED

FULLY RETRACTEDB2

Ø 3.50

15.50

Ø 3.00

7.50

39.5

0

B1

C7.50

4.50

Ø 3.

50

A

Ø 8h

6

Ø 3.

00

FULLY EXTENDED

FULLY RETRACTEDB2

AIR EXHAUST

Ø 3.50

7.50

Ø 3.

00

C

Ø 3.

50

4.50 A

Ø 8h

6

B1 FULLY EXTENDED

FULLY RETRACTEDB2

C

AØ

8h6

B1 FULLY EXTENDED

FULLY RETRACTEDB2

Ø 4.30

15.50

21.5

0

7.50

Ø 3.00

52.00Ø 3.

50

Ø 6h

6


6.00

16.00 FULLY EXTENDED

43.00

12.0

0

2.50

7.00

DTR/2/P DTR/5/P DTR/10/P DTR/20/P

A 38.50 57.50 82.50 113.50 C 2.00 2.00 2.00 3.00

B1 13.90 17.40 25.40 33.90

B2 10.90 11.40 14.40 12.90

DT/2/P DT/5/P DT/10/P DT/20/P

A 52.50 71.00 96.00 127.00 C 2.00 2.00 2.00 3.00

B1 13.90 17.40 25.40 33.90

B2 10.90 11.40 14.40 12.90

DTR/2/P DTR/5/P DTR/10/P DTR/20/P

A 38.50 57.50 82.50 113.50 C 2.00 2.00 2.00 3.00

B1 13.90 17.40 25.40 33.90

B2 10.90 11.40 14.40 12.90

DJ/2/P DJ10/2/P DJ/5/P DJ/10/P

A 52.0 84.0 71.0 96.0 C

7.0 7.0 7.0 7.0

B1 15.4 26.9 18.9 26.9

B2 12.4 15.9 12.9 15.9

Pneumatic Push (DP/P)

Right Angled Pneumatic Push (DTR/P)90° output/ non braided cable

Feather Touch Pneumatic Push (DT/P)

Right Angled Feather Touch Pneumatic Push (DTR/P)90° output/ braided cable

Gaiter Independent Pneumatic Push (DJ/P)Gaiter Independent Slim 6mm Ø Pneumatic Push (D6J/2/P)

23

96.00

Ø 3.

50

Ø 3.

00 7.50

4.50FULLY RETRACTED

FULLY EXTENDED

Ø 8h

6

2.00

21.4010.40

Ultrs Feather Touch Pneumatic Push (UT/10/P)

[email protected]

IN 3

PO

SIT

ION

S

Ø 4h

7

20.0

0

29.5

0

50.00

Ø 3.

00

8.00

18.00

47.0

018

.50

10.5

0

Ø 3.

50

20.0

0Ø 7.

50

7.70

40.00 5.00IN 2 POSITIONSM5 X 0.8-6H

Ø 6h

6

6.00 TYP

10.00

24.50 6.00 A/F

Ø 8h

6

Ø 10

.00

23.1

5

31.1

556

.35

22.80

Ø 3.

00

IN 3

PO

SIT

ION

S

Ø 4h

724

.50

IN 4 POSITIONS

8.00

18.0030.00

Ø 3.

50

M6 X 1-6H

A

11.7

0B 5.00

15.00C

8.00 A/F

24.5

037.0

0

ALTERNATIVERIGHT ANGLEOUTLETTRANSDUCER

30-35

Dimensions (mm): Specialist gauge probes

Block gauge2mm

Block gauges5mm and

10mm

Block gaugeconfi gurations

24

Spring on

Spring

Spring

Springholder

Springholder

Springholder

Spring Springholder

Springholder

Spring on

Pneumatic onSpring return

Pneumatic offSpring on

Pneumatic offSpring on

Pneumatic onSpring return

Air

inle

tn

ozz

le

Air

inle

tn

ozz

le

Pneumaticactuator

Pneumaticactuator

Spring Springholder

5mm 10mm

A 74.50 90.00

B 60.00 75.00

C 30.00 45.00

[email protected]

20.00 10.00

7.8

0

37.0

0

M4 X 0.7-6HIN 2 POSITIONS

Ø6h6

8.00

24.00

18.00

12.006.00

IN 3

PO

SIT

ION

S

Ø4h7

5 HOLESM3 X 0.5-6H X6.00 DEEP

69.0

0

Ø3.5

0

40.00

6.0

0

10.5

0

18.5

0

27.00

Ø3.0

0

22.0

0

6.00 A/F

7.5

0

11.00 MID TRAVEL


Flexure gauge

Block gauge / Flexure gauge accessories

Pneumatic actuator

Block gauges and flexure gauges are suppliedwithout pneumatic actuators as standard.Please order separately.

Tips (see page 34)Standard M2.5 thread

Tip carriers4mm Ø , choice of 20, 30,40mm length (all).6mm Ø , choice of 20, 30,40mm length (5 & 10mmblock gauges only)

Tool holders4mm bore (all)6mm bore (5 & 10mmblock gauges only)

Block gauge springs

A set of springs (of different forces) is includedwith each gauge. Replacements can beordered individually or as sets.



Mini probe 0.5mm Lever probe

Mini probe tips

Ø 3.00mm Ball

Tip material Part no.

T. Carbide 804847

Ruby 804582

Silicon Nitride 804982

R12.70mm Ball

Tip material Part no.

T. Carbide 804857

Mounting blocksThe lever probe can be clampeddirectly into a 9.52 mm mountinghole. Alternatively the followingmounting blocks are available;

Industry standarddovetail mountingblock

8 mm pegmounting block

Ball tipped styliLever probe styli are available in arange of ball diameters. All have1-75 UNF mounting threads.

Ball Ø

0.38

0.79

1.59

2.54

D= DATUM

0.050

3.75

3.00 A/F

9.25

MA

X.

11.7

5/11

.80

AT

RE

ST

7.25 MAX.

PROTECTIVERUBBER BOOT

R1.50

10.0

0

7.50/7.5530.55D

28.00

CHAMFER 1.80/2.00 X 45°IN 2 POSITIONS

3.75

4.00

D

D

Ø 3.20 THROUGH HOLEC/BOREDØ 5.70/5.80 X 4.50 DEEP

0.050

4.00

7.25

MA

X

6.25 MAX

7.50

3.25

Ø 3.20 THROUGH HOLEC/BOREDØ 5.70/5.80 X 3.50 DEEP

25.35 6.50/6.55

9.25

/9.3

0 A

T R

ES

T

23.50

D

D

D

3.25

R1.50 3.00 A/F

CHAMFER 1.80/2.00 X 45°IN 2 POSITIONS

PROTECTIVERUBBER BOOT

D= DATUM

PIECONNECTOR

EARTH

RE

DB

LUE

70mm

35mm

0.3m +

0.1-0.0m

ID LA

BE

LY

ELLO

W

Mini probe 1.00mm

Ø 3.50

30.00

37.00

Ø 9.512

Ø 9.500

2.25 22.86

Ø 1.59

30.00

6.00

Ø 3.00

2.90

/3.0

0

A/F

6.25

1.40

M2 x 0.4

(REF)

R16.0/10.0

Ø 3.00

1.25/0.75

2.90

/3.0

0

A/F

6.25

1.30

M2 x 0.4

Mini probecable assembly

[email protected]

Dimensions (mm): Orbit interface components

66.00

65.00

35.00

34.3

510

.50

23.20

19.90

16.40

71.50

46.0

0

19.00 MOUNTING

19.00MOUNTING

47.802 OFF M4 MOUNTING POSITIONS 23.20

19.90

16.4065.00

66.00

35.00

23.90

34.3

5 46.0

0

8.00

19.0

019

.00

VIEW SHOWING 3 ASSEMBLIES PLUGGED TOGETHERVIEW SHOWING 3 ASSEMBLIES PLUGGED TOGETHER

XXXA

123Y

ZZ9X

XXXX

-X

DP/X

X/X

61.00

72.0

017

.70

77.5

0

PIE (Probe Interface Electronics)

T-CON Orbit network connector

T-CON with mounting feet optionT-CON with 32 mm DIN raise connector



PSIM (Power Supply Interface Module)

28

19.00 MOUNTING

19.00MOUNTING

71.50

23.20

19.90

VIEW SHOWING 3 ASSEMBLIES PLUGGED TOGETHER

99.0

0

105.

00

10.5

0

17.70

66.00

65.00

9XXX

XX-XDP

/XX/

XXX

XA123YZZ

39.5

0

4.50

TY

P4

PO

SIT

ION

S

128.00

29.0

0

6.00 TYP4 POSITIONS

57.0

0

152.00

36.0

0

38.9

0

3D VIEW OF MOUNTING BRACKET

PSIM transformer

[email protected]

Other Orbit transducersOverview

29

S SeriesThe S Series of DisplacementTransducers is the culmination of manyyears’ experience and careful note ofmarket feedback.

u 5mm to 150mm measurement range

u <0.2% Linearity FRO

u Hermetically sealed andsubmersible on request

u IP65 or IP67 protection

u Rugged 19mm diameter stainlesssteel construction

u Excellent measurement range tobody length ratio

u Large bore to core clearance

u Wide range of accessories

SR SeriesBased on the S Series, SR ruggediseddisplacement transducers are designedspecifically for use in challengingenvironments in laboratory & test andprocess applications.

u 5mm to 150mm measurement range

u <0.2% Linearity FRO

u Rugged construction for use indemanding environments

u IP68 and hermetically sealedversions available

u Stainless steel body and corecarrier

Optimum SeriesWith a 9.5mm body diameter, theOptimum Series of LVDT displacementtransducers is the ideal choicefor process control and researchapplications where space is limited.Optimum Series transducers areavailable with free or guided core.

u Small 9.5mm body diameter

u Excellent measurement range tolength ratio

u Large radial core to bore clearance

u 3, 12, 25mm measurement range

u Rugged stainless steel construction

u 0.25% Linearity FRO

LE Series Linear Encodersu A choice of 12mm or 25mm

measurement ranges

u Spring, free, pneumatic, cablerelease

u Choice of IP65 or IP50 (probe only)

u Up to 0.4µm accuracy

u Up to 0.0125µm resolution

u CE approved

u Verification / calibration traceable toNPL (National Physical Laboratory)

linear encoders are highly accurateoptical gauges designed for use inapplications where consistent submicron measurement is required.

In contrast to traditional gaugingprobes, accuracy is maintained alongthe entire measurement range.

[email protected]

IMT Orbit Catalogue - Innovative Measurement Technology Ltd.

Documents

Transcript of IMT Orbit Catalogue - Innovative Measurement Technology Ltd.