BILGE WATER SEPARATORS

BILGE WATER SEPARATORS

CPS 3.2E+EBM 14X1New state-of the Art design.• Smaller volume 0.53 m3• Smaller working weight 412 Kgs• Treatment capacity 17.28m3/day• Does not use absorbents• IMO MEPC 107(49) APPROVED

The CPS is based on easy maintenance technology.It uses Peco Facets Mpak®technology with effi-cient membranes that accomplish high efficiency in chemical and mechanical emulsion breaking.Its lightweight, easy maintenance and space sav-ing.All systems are controlled through a PLC.

Main features:The CPS 3.2E + EBM 14x1 is approved for a flow rate of 0.73 m3/h• Supplied ready to install, coming complete with pump, valves and control panel• With the exception of the pump and solenoid valves this Bilge Water Separator has no mobile components. The level control is fixed and has no float• Maintenance requirements are very low, being restricted to occasional hosing down of the plate packs, and disposable membrane replacement. Access for cleaning is extremely simpleand easy to carry out• Separated hydrocarbon does normally contain less than 5% of water and this can be burned, if required• Oil discharge is facilitated by connection to the ship’s pressurized clear water system• The electrical power is at 380/440 V, 50 or 60 Hz

Dimensions:- LxBxH: 1003x980x565mm- Weight empty: 286kg- Weight in use:412kg

Extra options:• Electric heater in the oil dome to facilitate oil discharge (optional)

M: +47 415 05 599 E: oyvind@sandtorv-haugesund.no Bøvågen 30, N-4262 Avaldsnes

CPS BMKIII+EBM14X

New state-of the Art design.• Smaller volume 0.53 m3• Smaller working weight 412 Kgs• Treatment capacity 17.28m3/day• Does not use absorbents• IMO MEPC 107(49) APPROVED

The CPS is based on easy maintenance technology.It uses Peco Facets Mpak®technology with efficient membranes that accomplish high efficiency in chem-ical and mechanical emulsion breaking.Its lightweight, easy maintenance and space saving.All systems are controlled through a PLC.

Main features:• Capacity : 0.5 m3/h (2.2 US GPM) up to 10 m3/h (44 US GPM)• Supplied ready to install, coming complete with pump, valves and control panel• With the exception of the pump and solenoid valves this Bilge Water Separator has no mobile components. The level control is fixed and has no float• Maintenance requirements are very low, being restricted to occasional hosing down of the plate packs, and disposable membrane replacement. Access for cleaning is extremely simpleand easy to carry out• Separated hydrocarbon does normally contain less than 5% of water and this can be burned, if required• Oil discharge is facilitated by connection to the ship’s pressurized clear water system• The electrical power is at 380/440 V, 50 or 60 Hz

MODEL DIMENSION(mm)

FLOW  (m3/h)

WEIGHT  (kg)

WORKINGWEIGHT (kg)

■ a d eCPS  2.5B  MKIII+EBM  14x1 457 860 820 0,5 260 430CPS5BMKIII+EBM  14x1 457 1145 850 1 280 470CPS  10B  MKIII+EBM  14x2 457 1755 820 2,5 415 725CPS  25B  MKIII+EBM  3  14x2 900 1565 1315 5 735 1765CPS  50B  MKIII+EBM  3  14x3 900 2185 1315 10 810 2430

M: +47 415 05 599 E: oyvind@sandtorv-haugesund.no Bøvågen 30, N-4262 Avaldsnes

WE OFFER TAILORMADE SOLUTIONS FOR FILTRATION AND CLEANING OF LUBE, FUEL, HYDRAULIC,AIR,WATER,BALLAST AND BILGE

WATER.