Post on 03-Apr-2023
2 Warranty and Copyright information
Warranty and Copyright information
Limited warranty
BenQ warrants this product against any defects in material and workmanship, under normal usage and storage.
Proof of purchase date will be required with any warranty claim. In the event this product is found to be defective within the warranty period, BenQ's only obligation and your exclusive remedy shall be replacement of any defective parts (labor included). To obtain warranty service, immediately notify the dealer from which you purchased the product of any defects.
Important: The above warranty shall be void if the customer fails to operate the product in accordance with BenQ's written instructions, especially the ambient humidity must be in-between 10% and 90%, temperature in-between 0°C and 35°C, altitude lower than 4920 feet, and avoiding to operate the projector in a dusty environment. This warranty gives you specific legal rights, and you may have other rights which vary from country to country.
For other information, please visit www.BenQ.com.
Copyright
Copyright © 2021 by BenQ Corporation. All rights reserved. No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system or translated into any language or computer language, in any form or by any means, electronic, mechanical, magnetic, optical, chemical, manual or otherwise, without the prior written permission of BenQ Corporation.
Disclaimer
BenQ Corporation makes no representations or warranties, either expressed or implied, with respect to the contents hereof and specifically disclaims any warranties, merchantability or fitness for any particular purpose. Further, BenQ Corporation reserves the right to revise this publication and to make changes from time to time in the contents hereof without obligation to notify any person of such revision or changes.
*DLP, Digital Micromirror Device and DMD are trademarks of Texas Instruments. Others are copyrights of their respective companies or organizations.
Patents
Please go to http://patmarking.benq.com/ for the details on BenQ projector patent coverage.
3 Table of Contents
Table of ContentsWarranty and Copyright information ................................................................................ 2
Important safety instructions .............................................................................................. 4
Introduction .......................................................................................................................... 7Shipping contents ....................................................................................................................................... 7Projector exterior view ............................................................................................................................ 8Controls and functions.............................................................................................................................. 9
Positioning your projector ................................................................................................. 12Choosing a location .................................................................................................................................12Obtaining a preferred projected image size....................................................................................... 13Mounting the projector ..........................................................................................................................14Adjusting the projected image ..............................................................................................................15
Connection .......................................................................................................................... 17Connecting smart devices ......................................................................................................................18
Operation ............................................................................................................................ 19Starting up the projector ........................................................................................................................19Using the menus ....................................................................................................................................... 21Securing the projector ............................................................................................................................22Switching input signal ...............................................................................................................................24Shutting down the projector .................................................................................................................24Direct power off....................................................................................................................................... 25
Menu operation ................................................................................................................... 26Menu System .............................................................................................................................................26Basic menu ............................................................................................................................................... 30Advanced menu ..................................................................................................................................... 32
Maintenance ........................................................................................................................ 39Care of the projector ..............................................................................................................................39Lamp information ..................................................................................................................................... 40
Troubleshooting ................................................................................................................. 44
Specifications ...................................................................................................................... 45Projector specifications ..........................................................................................................................45Dimensions ................................................................................................................................................46Timing chart............................................................................................................................................... 47RS232 command ....................................................................................................................................... 49
4 Important safety instructions
Important safety instructionsYour projector is designed and tested to meet the latest standards for safety of information technology equipment. However, to ensure safe use of this product, it is important that you follow the instructions mentioned in this manual and marked on the product.
1. Please read this manual before you operate your projector. Save it for future reference.
2. Do not look straight at the projector lens during operation. The intense light beam may damage your eyes.
3. Refer servicing to qualified service personnel.
4. Always open the lens shutter (if any) or remove the lens cap (if any) when the projector lamp is on.
5. The lamp becomes extremely hot during operation. Allow the projector to cool for approximately 45 minutes prior to removing the lamp assembly for replacement.
6. In some countries, the line voltage is NOT stable. This projector is designed to operate safely within a mains voltage between 100 to 240 volts AC, but could fail if power cuts or surges of ±10 volts occur. In areas where the mains voltage may fluctuate or cut out, it is recommended that you connect your projector through a power stabilizer, surge protector or uninterruptible power supply (UPS).
7. Do not block the projection lens with any objects when the projector is under operation as this could cause the objects to become heated and deformed or even cause a fire. To temporarily turn off the lamp, use the blank function.
8. Do not operate lamps beyond the rated lamp life. Excessive operation of lamps beyond the rated life could cause them to break on rare occasions.
5 Important safety instructions
9. Never replace the lamp assembly or any electronic components unless the projector is unplugged.
10. Do not place this product on an unstable cart, stand, or table. The product may fall, sustaining serious damage.
11. Do not attempt to disassemble this projector. There are dangerous high voltages inside which may cause death if you should come into contact with live parts. The only user serviceable part is the lamp which has its own removable cover.
Under no circumstances should you ever undo or remove any other covers. Refer servicing only to suitably qualified professional service personnel.
12. Do not block the ventilation holes.
- Do not place this projector on a blanket, bedding or any other soft surface.
- Do not cover this projector with a cloth or any other item.
- Do not place inflammables near the projector.
If the ventilation holes are seriously obstructed, overheating inside the projector may result in a fire.
13. Always place the projector on a level, horizontal surface during operation.
- Do not use if tilted at an angle of more than 10 degrees left to right, nor at angle of more than 15 degrees front to back. Using the projector when it is not fully horizontal may cause a malfunction of, or damage to, the lamp.
14. Do not stand the projector on end vertically. Doing so may cause the projector to fall over, causing injury or resulting in damage to the projector.
15. Do not step on the projector or place any objects upon it. Besides probable physical damage to the projector, doing so may result in accidents and possible injury.
16. When the projector is under operation, you may sense some heated air and odor from its ventilation grill. It is a normal phenomenon and not a product defect.
6 Important safety instructions
17. Do not place liquids near or on the projector. Liquids spilled into the projector may cause it to fail. If the projector does become wet, disconnect it from the power supply's power outlet and call BenQ to have the projector serviced.
18. This product is capable of displaying inverted images for ceiling/wall mount installation.
19. This apparatus must be earthed.
20. Do not place this projector in any of the following environments.
- Space that is poorly ventilated or confined. Allow at least 50 cm clearance from walls and free flow of air around the projector.
- Locations where temperatures may become excessively high, such as the inside of a car with all windows rolled up.
- Locations where excessive humidity, dust, or cigarette smoke may contaminate optical components, shorten the projector's life span and darken the image.
- Locations near fire alarms- Locations with an ambient temperature above 40°C /
104°F- Locations where the altitudes are higher than 3000 m
(10000 feet).
Risk Group 21. According to the classification of
photobiological safety of lamps and lamp systems, this product is Risk Group 2, IEC 62471-5:2015.
2. Possibly hazardous optical radiation emitted from this product.
3. Do not stare at operating lamp. May be harmful to the eyes.
4. As with any bright source, do not stare into the direct beam.
Hg - Lamp contains mercury. Manage in accordance with local disposal laws. See www.lamprecycle.org.
To avoid damaging the DLP chips, never aim a high-power laser beam into the projection lens.
3000 m(10000 feet)
0 m(0 feet)
7 Introduction
Introduction
Shipping contentsCarefully unpack and verify that you have all of the items shown below. If any of these items are missing, please contact your place of purchase.
Standard accessories
Optional accessories
Replacing the remote control batteries
1. Press and slide off the battery cover, as illustrated.
2. Remove the old batteries (if applicable) and install two AAA batteries. Make sure that the positive and negative ends are positioned correctly, as illustrated.
3. Slide the battery cover in until it clicks into place.
ProjectorRemote control with
batteriesQuick start guide
Warranty card* Power cord
• The supplied accessories will be suitable for your region, and may differ from those illustrated.
• *The warranty card is only supplied in some specific regions. Please consult your dealer for detailed information.
1. Spare lamp kit
2. 3D glasses
• Avoid leaving the remote control and batteries in an excessive heat or humid environment like the kitchen, bathroom, sauna, sunroom or in a closed car.
• Replace only with the same or equivalent type recommended by the battery manufacturer.
• Dispose of the used batteries according to the manufacturer's instructions and local environment regulations for your region.
• Never throw the batteries into a fire. There may be danger of an explosion.
• If the batteries are dead or if you will not be using the remote control for an extended period of time, remove the batteries to avoid damage to the remote control from possible battery leakage.
8 Introduction
Projector exterior view
1. Focus ring and Zoom ring
2. Vent (air exhaust)
3. Adjuster feet
4. Projection lens
5. IR remote sensor
6. External control panel(See Controls and functions on page 9.)
7. Lamp cover
8. Vent (air inlet)
9. Audio input jacksAudio output jack
10. HDMI 2 input port
11. HDMI 1/MHL input port
12. USB Type A port
13. RS-232 control port
14. AC power jack
15. Kensington anti-theft lock slot
16. Ceiling mount holes
76
16
18
18
8
3
3
3 3
54
1
2
9 10 11 12
14 15
13
9 Introduction
Controls and functions
Projector & Remote control
1. POWER
Toggles the projector between standby mode and on.
ON/ Off
Toggles the projector between standby mode and on.
2. POWER indicator light/TEMPerature warning light/LIGHT indicator light(See Indicators on page 43.)
3. IR remote sensor
4. BACK
Goes back to previous OSD menu, exits and saves menu settings.
5. Arrow keys ( , , , )
When the On-Screen Display (OSD) menu is activated, these keys are used as directional arrows to select the desired menu items and to make adjustments.
Keystone keys ( , )
Displays the keystone correction page.
Volume keys /
Decreases or increase the projector volume.
2
9
76
8
51
34 10
All the key presses described in this document are available on the remote control or projector.
1
5
14
11
4
13
8
10
1216
6
7
17
15
10 Introduction
6. SOURCE
Displays the source selection bar.
7. ECO BLANK
Used to hide the screen picture.
Do not block the projection lens from projecting as this could cause the blocking object to become heated and deformed or even cause a fire.
8. OK
Confirms the selected On-Screen Display (OSD) menu item.
9. AUTO
Automatically determines the best picture timings for the displayed image when PC signal (analog RGB) is selected.
* Available on compatible projectors only.
10. MENU
Turns on the On-Screen Display (OSD) menu.
11.
Displays the keystone menu.
12. PIC MODE
Selects the picture mode.
13.
Toggles projector audio between on and off.
14. MHL Zone
Controls video or audio playback under MHL source.
15. SOUND MODE
This projector does not support SOUND MODE function.
16. LUMIEXPERT BOOST
This projector does not support LumiExpert function.
17. Volume keys /
Decreases or increases the projector volume.
11 Introduction
Controlling your smart device with the AUTO buttonWhen the projector projects the content from your MHL compatible smart device, you can use the remote control to control your smart device.
To enter the MHL mode, press and hold AUTO on the projector keypad for 3 seconds. The MHL Zone keys on the remote control are available for controlling your smart device.
Remote control effective rangeThe remote control must be held at an angle within 30 degrees perpendicular to the projector's IR remote control sensor(s) to function correctly. The distance between the remote control and the sensor(s) should not exceed 8 meters (~ 26 feet).
Make sure that there are no obstacles between the remote control and the IR sensor(s) on the projector that might obstruct the infra-red beam.
When the projector is under MHL mode, the keypad on the projector should be with the same definition of the keys on the remote control.
• Operating the projector from the front • Operating the projector from the top
Approx. +30º
Approx. +30º
12 Positioning your projector
Positioning your projector
Choosing a locationBefore choosing an installation location for your projector, take the following factors into consideration:
• Size and position of your screen
• Electrical outlet location
• Location and distance between the projector and the rest of your equipment
You can install your projector in the following ways.
After turning on the projector, go to Basic Menu - Settings > Projector Installation, press OK and press / to select a setting.
You can also use QUICK INSTALL on the remote control to access this menu.
1. Front
Select this location with the projector placed on the table in front of the screen. This is the most common way to position the projector for quick setup and portability.
2. Rear
Select this location with the projector placed on the table behind the screen. Note that a special rear projection screen is required.
3. Front Ceiling
Select this location with the projector suspended upside-down from the ceiling in front of the screen. Purchase the BenQ Projector Ceiling Mount Kit from your dealer to mount your projector on the ceiling.
4. Rear Ceiling
Select this location with the projector suspended upside-down from the ceiling behind the screen. Note that a special rear projection screen and the BenQ Projector Ceiling Mount Kit are required for this installation location.
13 Positioning your projector
Obtaining a preferred projected image sizeThe distance from the projector lens to the screen, the zoom setting (if available), and the video format each factors in the projected image size.
Projection dimensions
• The screen aspect ratio is 16:9 and the projected picture is in a 16:9 aspect ratio
Screen size Projection Distance (mm)Offset (mm)
DiagonalH (mm) W (mm)
Min distance (with max zoom)
AverageMax distance
(with min zoom)Inch mm
30 762 374 664 996 1046 1096 19
40 1016 498 886 1328 1395 1461 25
50 1270 623 1107 1660 1743 1826 31
60 1524 747 1328 1992 2092 2192 37
70 1778 872 1550 2324 2441 2557 44
80 2032 996 1771 2657 2789 2922 50
90 2286 1121 1992 2989 3138 3287 56
100 2540 1245 2214 3321 3487 3653 62
110 2794 1370 2435 3653 3835 4018 68
120 3048 1494 2657 3985 4184 4383 75
130 3302 1619 2878 4317 4533 4749 81
140 3556 1743 3099 4649 4881 5114 87
150 3810 1868 3321 4981 5230 5479 93
160 4064 1992 3542 5313 5579 5844 100
170 4318 2117 3763 5645 5927 6210 106
180 4572 2241 3985 5977 6276 6575 112
190 4826 2366 4206 6309 6625 6940 118
200 5080 2491 4428 6641 6973 7306 125
210 5334 2615 4649 6973 7322 7671 131
220 5588 2740 4870 7306 7671 8036 137
230 5842 2864 5092 7638 8019 8401 143
240 6096 2989 5313 7970 8368 8767 149
250 6350 3113 5535 8302 8717 9132 156
260 6604 3238 5756 8634 9066 9497 162
270 6858 3362 5977 8966 9414 9862 168
280 7112 3487 6199 9298 9763 10228 174
290 7366 3611 6420 9630 10112 10593 181
300 7620 3736 6641 9962 10460 10958 187
H
WProjection distance
Center of lens
Screen16:9 Screen diagonal
14 Positioning your projector
For example, if you are using a 120-inch screen, the recommended projection distance in the "Average" column is 4184 mm.
If your measured projection distance is 4400 mm, the closest match in the "Average" column is 4533 mm. Looking across this row shows that a 130'' (about 3.3 m) screen is required.
Mounting the projectorIf you intend to mount your projector, we strongly recommend that you use a proper fitting BenQ projector mounting kit and that you ensure it is securely and safely installed.
If you use a non-BenQ brand projector mounting kit, there is a safety risk that the projector may fall down due to an improper attachment through the use of the wrong gauge or length screws.
Before mounting the projector• Purchase a BenQ projector mounting kit from the place you purchased your BenQ projector.
• BenQ recommends that you also purchase a separate Kensington lock compatible security cable and attach it securely to both the Kensington lock slot on the projector and the base of the mounting bracket. This will perform the secondary role of restraining the projector should its attachment to the mounting bracket become loose.
• Ask your dealer to install the projector for you. Installing the projector on your own may cause it to fall and result in injury.
• Take necessary procedures to prevent the projector from falling off such as during an earthquake.
• The warranty doesn’t cover any product damage caused by mounting the projector with a non-BenQ brand projector mounting kit.
• Consider the surrounding temperature where the projector is ceiling/wall mounted. If a heater is used, the temperature around the ceiling may be higher than expected.
• Read the user manual for the mounting kit about the range of torque. Tightening with torque exceeding the recommended range may cause damage to the projector and subsequently falling off.
• Make sure the power outlet is at an accessible height so that you can easily shut down the projector.
To optimize your projection quality, we suggest to do the projection within non-gray area.
All measurements are approximate and may vary from the actual sizes. BenQ recommends that if you intend to permanently install the projector, you should physically test the projection size and distance using the actual projector in situ before you permanently install it, so as to make allowance for this projector's optical characteristics. This will help you determine the exact mounting position so that it best suits your installation location.
15 Positioning your projector
Ceiling/Wall mount installation diagram
Adjusting the projected image
Adjusting the projection angleIf the projector is not placed on a flat surface or the screen and the projector are not perpendicular to each other, the projected image becomes trapezoidal. You can adjust the adjuster feet to fine-tune the horizontal angle.
To retract the feet, screw the adjuster feet in a reverse direction.
Do not look into the lens while the lamp is on. The strong light from the lamp may cause damage to your eyes.
Ceiling/Wall mount screw: M4(Max L = 25 mm; Min L = 20 mm)
Unit: mm
65.89
65.89
40.27
113.54 60
16 Positioning your projector
Fine-tuning the image size and clarity
Correcting keystoneKeystoning refers to the situation where the projected image becomes a trapezoid due to angled projection.
To correct this, you will need to manually correct it following these steps.
1. Do one of the following steps to display the keystone correction page.
• Press / on the projector. • Press on the remote control.
2. After the Keystone correction page displays. Press to correct keystoning at the top of the image. Press to correct keystoning at the bottom of the image.
Adjust the projected image to the size that you need using the zoom ring.
Sharpen the image by rotating the focus ring.
Press . Press .
17 Connection
ConnectionWhen connecting a signal source to the projector, be sure to:
1. Turn all equipment off before making any connections.
2. Use the correct signal cables for each source.
3. Ensure the cables are firmly inserted.
• In the connections above, some cables may not be included with the projector (see Shipping contents on page 7). They are commercially available from electronics stores.
• The connection illustrations are for reference only. The rear connecting jacks available on the projector vary with each projector model.
• Many notebooks do not turn on their external video ports when connected to a projector. Usually a key combo like FN + function key with a monitor symbol turns the external display on/off. Press FN and the labeled function key simultaneously. Refer to your notebook's documentation to find your notebook's key combination.
• If the selected video image is not displayed after the projector is turned on and the correct video source has been selected, check that the video source device is turned on and operating correctly. Also check that the signal cables have been connected correctly.
HDMI cable
Audio cable
HDMI wireless dongle
USB cable (A to Micro B type) connect to the power port of HDMI wireless dongle.
1
2
3
412
2
3
4
Notebook or desktop computerA/V device
Speakers
Smart device
18 Connection
Connecting audio
The projector has built-in mono speaker(s) which are designed to provide basic audio functionality accompanying data presentations for business purposes only. They are not designed for, nor intended for stereo audio reproduction use as might be expected in home theater or home cinema applications. Any stereo audio input (if provided), is mixed into a common mono audio output through the projector speaker(s).
The built-in speaker(s) will be muted when the AUDIO OUT jack is connected.
Connecting smart devicesThe projector can project the content directly from a smart device by using a wireless dongle.
HDMI wireless dongle
Connect the dongle to HDMI and USB TYPE-A ports on the projector and switch the input signal to HDMI 1/MHL or HDMI 2.
• The projector is only capable of playing mixed mono audio, even if a stereo audio input is connected.
• If the selected video image is not displayed after the projector is turned on and the correct video source has been selected, check that the video source device is turned on and operating correctly. Also check that the signal cables have been connected correctly.
19 Operation
Operation
Starting up the projector1. Plug the power cord. Turn on the power outlet switch
(where fitted). The power indicator on the projector lights orange after power has been applied.
2. Press on the projector or on the remote control to start the projector. The power indicator flashes green and stays green when the projector is on.
The start up procedure takes about 30 seconds. In the later stage of start up, a startup logo is projected.
(If necessary) Rotate the focus ring to adjust the image clearness.
3. If this is the first time you turn on the projector, the setup wizard appears to guide you through setting up the projector. If you have already done this, skip this step and move on to step 5.
• Use the arrow keys ( / / / ) on the projector or remote control to move through the menu items.
• Use OK to confirm the selected menu item.
The Setup Wizard screenshots below are for reference only and may differ from the actual design.
Step 1:
Specify Projector Position.
For more information about projector position, see Choosing a location.
Step 2:
Specify OSD Language.
Step 3:
Specify Vertical Keystone.
For more information about vertical keystone, see Correcting keystone.
20 Operation
4. If you are prompted for a password, press the arrow keys to enter a 6-digit password. See Utilizing the password function on page 22.
5. Switch all of the connected equipment on.
6. The projector will search for input signals. The current input signal being scanned appears. If the projector does not detect a valid signal, the message “No Signal” will continue displaying until an input signal is found.
You can also press SOURCE to select your desired input signal. See Switching input signal on page 24.
Step 4:
Specify Auto Source.
Select On if you want the projector to always search for available signals automatically when the projector is turned on.
Step 5:
Specify Menu Type.
For more information about menu types, see Using the menus.
Now you’ve completed the initial setup.
• Please use the original accessories (e.g. power cord) to avoid possible dangers such as electric shock and fire.
• If the projector is still hot from previous activity, it will run the cooling fan for approximately 90 seconds before energizing the lamp.
• The Setup Wizard screenshots are for reference only and may differ from the actual design.
• If the frequency/resolution of the input signal exceeds the projector's operating range, you will see the message “Out of Range” displayed on the background screen. Please change to an input signal which is compatible with the projector's resolution or set the input signal to a lower setting. See Timing chart on page 47.
• If no signal is detected for 3 minutes, the projector automatically enters saving mode.
21 Operation
Using the menusThe projector is equipped with 2 types of On-Screen Display (OSD) menus for making various adjustments and settings.
• Basic OSD menu: provides primary menu functions. (See Basic menu on page 30)
• Advanced OSD menu: provides full menu functions. (See Advanced menu on page 32)
To access the OSD menu, press MENU on the projector or remote control.
• Use the arrow keys ( / / / ) on the projector or remote control to move through the menu items.
• Use OK on the projector or remote control to confirm the selected menu item.
The first time you use the projector (after finishing the initial setup), Basic OSD menu displays.
Below is the overview of the Basic OSD menu.
If you intend to switch from the Basic OSD menu to the Advanced OSD menu, follow the instructions below:
1. Go to Basic Menu - Settings > Menu Type and press OK.
2. Press / to select Advanced and press OK. Your projector will switch to Advanced OSD menu.
Below is the overview of the Advanced OSD menu.
The OSD screenshots below are for reference only, and may differ from the actual design.
• Input signal connected • No input signal connected
Picture ModeVivid TV
Volume10
MuteOff
3D Mode3D Off
3D Sync InvertPress OK
SettingsPress OK
Fast ModeOff
Wall ColorOff
Auto SourceOff
Reset Light Timer
Projector PositionFront
Menu TypeBasic
Reset All Settings
Test PatternOff
HDMI RangeAuto
Information
Picture Mode
User Mode Management
Brightness
Contrast
Tint
Sharpness
Picture
7
PC
Vivid TV
ExitCurrent input source
Main menu icon
Main menu name
Submenu
Press BACK to go back to the previous window or to exit.
Status
50
50
50
50
Color
Advanced...
Reset Current Picture Mode
Selection bar
22 Operation
Likewise, when you wish to switch from the Advanced OSD menu to the Basic OSD menu, follow the instructions below:
1. Go to Advanced Menu - System Setup : Basic > Menu Settings and press OK.
2. Highlight Menu Type and press / to select Basic. Your projector will switch to the Basic OSD menu.
Securing the projector
Using a security cable lockThe projector has to be installed in a safe place to prevent theft. Otherwise, purchase a lock, such as the Kensington lock, to secure the projector. You can locate a Kensington lock slot on the rear side of the projector. See item 15 on page 8.
A Kensington security cable lock is usually a combination of key(s) and the lock. Refer to the lock’s documentation for finding out how to use it.
Utilizing the password functionSetting a password
1. Go to Advanced Menu - System Setup : Advanced > Password. Press OK. The Password page appears.
2. Highlight Change Password and press OK.
3. The four arrow keys ( , , , ) respectively represent 4 digits (1, 2, 3, 4). According to the password you desire to set, press the arrow keys to enter six digits for the password.
4. Confirm the new password by re-entering the new password.Once the password is set, the OSD menu returns to the Password page.
5. To activate the Power On Lock function, press / to highlight Power On Lock and press / to select On. Input the password again.
• The digits being input will display as asterisks on-screen. Make a note of your selected password and keep it in a safe place in advance or right after the password is entered so that it is available to you should you ever forget it.
• Once a password has been set and the power on lock is activated, the projector cannot be used unless the correct password is entered every time the projector is started.
Input New Password
Return
23 Operation
If you forget the password
If you enter the wrong password, the password error message will appear, and the Input Current Password message follows. If you absolutely do not remember the password, you can use the password recall procedure. See Entering the password recall procedure on page 23.
If you enter an incorrect password 5 times in succession, the projector will automatically shut down in a short time.
Entering the password recall procedure
1. Press and hold AUTO for 3 seconds. The projector will display a coded number on the screen.
2. Write down the number and turn off your projector.
3. Seek help from the local BenQ service center to decode the number. You may be required to provide proof of purchase documentation to verify that you are an authorized user of the projector.
Changing the password
1. Go to Advanced Menu - System Setup : Advanced > Password. Press OK. The Password page appears.
2. Highlight Change Password and press OK. The message “Input Current Password” appears.
3. Enter the old password.
• If the password is correct, another message “Input New Password” appears. • If the password is incorrect, the password error message will appear, and the message “Input Current Password”
appears for your retry. You can press BACK to cancel the change or try another password.
4. Enter a new password.
5. Confirm the new password by re-entering the new password.
Disabling the password function
To disable password protection, go to Advanced Menu - System Setup : Advanced > Password > Power On Lock and press / to select Off. The message “Input Current Password” appears. Enter the current password.
• If the password is correct, the OSD menu returns to the Security Settings page. You will not have to enter the password next time turning on the projector.
• Under the Advanced OSD menu • Under the Basic OSD menu
• Under the Advanced OSD menu • Under the Basic OSD menu
Password ErrorPlease try again.
Password ErrorPlease try again.
Please write down the recall code, and contact BenQ Customer Center.
Recall code:
XXX XXX XXX XXX
Recall Password
Exit
Recall Password
XXX XXX XXX XXX
Please write down the recall code, and contact BenQ Customer Center.
Recall code:
24 Operation
• If the password is incorrect, the password error message will appear, and the message “Input Current Password” appears for your retry. You can press BACK to cancel the change or try another password.
Switching input signalThe projector can be connected to multiple devices at the same time. However, it can only display one full screen at a time. When starting up, the projector automatically searches for the available signals.
Be sure the Advanced Menu - System Setup : Basic > Auto Source menu is On if you want the projector to automatically search for the signals.
To select the source:
1. Press SOURCE. A source selection bar appears.
2. Press / until your desired signal is selected and press OK.
Once detected, the selected source information will appear at the corner of the screen for seconds. If there is multiple equipment connected to the projector, repeat steps 1-2 to search for another signal.
Shutting down the projector
1. Press on the projector or on the remote control and a confirmation message will appear prompting you. If you don't respond in a few seconds, the message will disappear.
2. Press or a second time. The power indicator flashes orange, the projection lamp shuts down, and the fans will continue to run for approximately 90 seconds to cool down the projector.
3. Once the cooling process finishes, the power indicator becomes a steady orange and fans stop. Disconnect the power cord from the power outlet.
Though the password function is disabled, you need to keep the old password in hand should you ever need to re-activate the password function by entering the old password.
• The brightness level of the projected image will change accordingly when you switch between different input signals.
• For best display picture results, you should select and use an input signal which outputs at the projector’s native resolution. Any other resolutions will be scaled by the projector depending upon the “aspect ratio” setting, which may cause some image distortion or loss of picture clarity. See Aspect Ratio on page 35.
• To protect the lamp, the projector will not respond to any commands during the cooling process.
• To shorten the cooling time, you can also activate the Quick cooling function. See Quick Cooling on page 37.
• Avoid turning on the projector immediately after turning it off as excessive heat may shorten lamp life.
• Lamp life results will vary depending on environmental conditions and usage.
HDMI 1/MHL
HDMI 2
Source
25 Operation
Direct power offThe AC power cord can be pulled out right after the projector is turned off. To protect the lamp, wait about 10 minutes before re-starting the projector. If you attempt to re-start the projector, the fans may
run for a few minutes to cool down. In such cases, press or again to start the projector after the fans stop and the power indicator turns orange.
26 Menu operation
Menu operationPlease note that the on-screen display (OSD) menus vary according to the signal type selected and the projector model you are using.
The menu items are available when the projector detects at least one valid signal. If there is no equipment connected to the projector or no signal detected, limited menu items are accessible.
Menu System
Basic Menu
Sub-menu Options
Picture ModeBright/Living Room/Cinema/Game/Sports/User 1/User 2/(3D)
Volume 0~10~20Mute On/OffFast Mode On/Off
3D ModeAuto/3D Off/Frame Sequential/Frame Packing/Top-Bottom/Side-by-Side
3D Sync InvertSettings
27 Menu operation
Advanced Menu
Main menu Sub-menu Options
PICTURE
Picture ModeBright/Living Room/Cinema/Sports/Game/User 1/User 2/(3D)
User Mode Management
Bright/Living Room/Cinema/Sports/Game/User 1/User 2Rename User Mode
Brightness 0~50~100Contrast 0~50~100Sharpness 0~7~15
Advanced
Gamma Selection
1.6/1.8/2.0/2.1/2.2/2.3/2.4/2.6/2.8/BenQ
Color Temperature
Preset (Normal/Cool/Lamp Native/Warm)Red Gain (0~200)Green Gain (0~200)Blue Gain (0~200)Red Offset (0~511)Green Offset (0~511)Blue Offset (0~511)
Color Management
R (Hue/Saturation/Gain)G (Hue/Saturation/Gain)B (Hue/Saturation/Gain)C (Hue/Saturation/Gain)M (Hue/Saturation/Gain)Y (Hue/Saturation/Gain)White (R Gain/G Gain/B Gain)
Noise Reduction
0~31
Brilliant Color 0~10Fast Mode On/Off
Light ModeNormal/Economic/SmartEco/LampSave
Reset Current Picture Mode
Reset/Cancel
Sound
Mute On/OffVolume 0~10~20Power On/Off Ring Tone
On/Off
Reset Audio Settings
Reset/Cancel
28 Menu operation
DISPLAY
Aspect Ratio Auto/Real/4:3/16:9/16:10Wall Color Off/Light Yellow/Pink/Green/BlueOverscan Adjustment
0~1~3
3D3D Mode
Auto/3D Off/Frame Sequential/Frame Packing/Top-Bottom/Side-by-Side
3D Sync InvertDigital Lens Shift
-20~0~20
SYSTEM SETUP: BASIC
Language
Background Color Black/Blue/PurpleSplash Screen BenQ/Black/Blue
Projector PositionFront/Front Ceiling/RearRear Ceiling
Auto OffDisable/5 min/10 min/15 min/20 min/25 min/30 min
Direct Power On On/Off
Menu Settings
Menu Type Basic/Advanced
Menu PositionCenter/Top-Left/Top-Right/Bottom-Right/Bottom-Left
Menu Display Time
Always On/5 sec/10 sec/15 sec/20 sec/25 sec/30 sec
Blank Reminder Message
On/Off
Source RenameAuto Source On/Off
Main menu Sub-menu Options
29 Menu operation
SYSTEM SETUP: ADVANCED
Light Settings
Reset Light Timer
Reset/Cancel
Light Usage Time
HDMI Settings HDMI Range Auto/Full/Limited
Baud Rate9600/14400/19200/38400/57600/115200
Test Pattern On/OffQuick Cooling On/OffHigh Altitude Mode On/Off
PasswordChange PasswordPower On Lock On/Off
Key Lock On/OffLED Indicator On/OffReset All Settings Reset/Cancel
INFORMATION
SourcePicture ModeResolutionColor SystemLight Usage Time3D FormatFirmware VersionService Code
Main menu Sub-menu Options
30 Menu operation
Basic menu
Picture Mode
The projector is preset with several predefined picture modes so that you can choose one to suit your operating environment and input signal picture type.
• Bright: Maximizes the brightness of the projected image. This mode is suitable for environments where extra-high brightness is required, such as using the projector in well lit rooms.
• Living Room: Being slightly brighter than Cinema mode, it is suitable for playing movies in rooms where there is a small amount of ambient light, eg. your living room.
• Cinema: With well-balanced color saturation and contrast with a low brightness level, this is most suitable for enjoying movies in a totally dark environment (as you would find in a commercial cinema).
• Sports: This mode is best for watching sporting events in rooms where is a small amount of ambient light, et. your living room.
• Game: This mode is best for playing video games in rooms where there is a small amount of ambient light, eg. your living room.
• User 1/User 2: Recalls the settings customized based on the current available picture modes. See User Mode Management on page 32.
Volume Adjusts the sound level.
Mute Temporarily turns off the sound.
Fast Mode Select to turn On or Off the Fast Mode.
3D Mode
This projector supports playing three-dimensional (3D) content transferred through your 3D-compatible video devices and contents, such as PlayStation consoles (with 3D game discs), 3D Blu-ray players (with 3D Blu-ray discs), 3D TV (with 3D channel), and so on. After you have connected the 3D video devices to the projector, wear the BenQ 3D glasses and make sure the power is on to view 3D contents.
When watching 3D contents,
• the image may seem misplaced, however, this is not a product malfunction.
• take appropriate breaks when watching 3D content.
• stop watching 3D content if you feel fatigue or discomfort.
• keep a distance from the screen of about three times the effective height of the screen when watching 3D content.
• children and people with a history of oversensitivity to light, heart problems, or have any other existing medical condition should be refrained from watching 3D content.
31 Menu operation
3D Mode
The default setting is Auto and the projector automatically chooses an appropriate 3D format when detecting 3D contents. If the projector cannot recognize the 3D format, manually choose a 3D mode according to your preference.
When this function is enabled:
• The brightness level of the projected image decreases.
• The Picture Mode cannot be adjusted.
• The Vertical Keystone can only be adjusted within limited degrees.
The function is accessible through the remote control.
3D Sync Invert
When your 3D image is distorted, enable this function to switch between the image for the left eye and the right eye for comfortable 3D viewing experience.
The function is accessible through the remote control.
Settings
Press OK to enter its submenu.
Press BACK to save your changes and exit.
See below for more details.
32 Menu operation
Advanced menu
Picture0
Picture Mode
The projector is preset with several predefined picture modes so that you can choose one to suit your operating environment and input signal picture type.
• Bright: Maximizes the brightness of the projected image. This mode is suitable for environments where extra-high brightness is required, such as using the projector in well lit rooms.
• Living Room: Being slightly brighter than Cinema mode, it is suitable for playing movies in rooms where there is a small amount of ambient light, eg. your living room.
• Cinema: With well-balanced color saturation and contrast with a low brightness level, this is most suitable for enjoying movies in a totally dark environment (as you would find in a commercial cinema).
• Sports: This mode is best for watching sporting events in rooms where is a small amount of ambient light, et. your living room.
• Game: This mode is best for playing video games in rooms where there is a small amount of ambient light, eg. your living room.
• User 1/User 2: Recalls the settings customized based on the current available picture modes. See User Mode Management on page 32.
• 3D: Is appropriate for playing 3D images and 3D video clips.
User Mode Management
There are 2 user-definable modes if the current available picture modes are not suitable for your need. You can use one of the picture modes (except the User 1/User 2) as a starting point and customize the settings.
1. Go to Picture > Picture Mode.
2. Press / to select User 1 or User 2.
3. Press to highlight User Mode Management and press OK.
4. Highlight Load Settings From and press OK.
5. Press to select a picture mode that is close to your need.
6. When done, press OK and BACK to return to the Picture menu.
7. Press to select other submenus you want to make changes and use / to adjust the values. The adjustments define the selected user mode.
• Rename User Mode
Select to rename the customized picture modes (User 1 or User 2).
1. Go to the Picture > Picture Mode menu, select User 1 or User 2.
2. Press to select User Mode Management.
3. On the User Mode Management window, select Rename User Mode and press OK.
4. On the Rename User Mode window, use / / / to select desired characters for the selected mode.
5. When done, press OK and BACK to exit.
33 Menu operation
BrightnessThe higher the value, the brighter the image. Adjust this control so the black areas of the image appear just as black and that detail in the dark areas is visible.
ContrastThe higher the value, the greater the contrast. Use this to set the peak white level after you have previously adjusted the Brightness setting to suit your selected input and viewing environment.
Sharpness The higher the value, the sharper the picture becomes.
Advanced
Gamma Selection
Gamma refers to the relationship between input source and picture brightness.
• 1.6/1.8/2.0/2.1: Select these values according to your preference.• 2.2/2.3: Increases the average brightness of the picture. Best for a lit environment, meeting
room or family room.• 2.4: Best for viewing movies in a dark environment.• 2.6/2.8/BenQ: Best for viewing movies which are mostly composed of dark scenes.
Color Temperature
There are several preset color temperature settings available. The available settings may vary according to the signal type selected.
• Lamp Native: With the lamp’s original color temperature and higher brightness. This setting is suitable for environments where high brightness is required, such as projecting pictures in well lit rooms.
• Warm: Makes images appear reddish white.• Normal: Maintains normal colorings for white.• Cool: Makes images appear bluish white.
High BrightnessLow Contrast
Low BrightnessHigh Contrast
1.6 1.8 2.0 2.1 2.2 2.3 2.4 2.6 2.8 BenQ
34 Menu operation
Advanced
Color Management
This function provides six sets (RGBCMY) of colors to be adjusted. When you select each color, you can independently adjust its range and saturation according to your preference.
• Primary Color: Selects a color from among R (Red), G (Green), B (Blue), C (Cyan), M (Magenta), or Y (Yellow).
• Hue: Increase in the range will include colors consisted of more proportions of its two adjacent colors. Please refer to the illustration for how the colors relate to each other.For example, if you select Red and set its range at 0, only pure red in the projected picture will be selected. Increasing its range will include red close to yellow and red close to magenta.
• Saturation: Adjusts the values to your preference. Every adjustment made will reflect to the image immediately. For example, if you select Red and set its value at 0, only the saturation of pure red will be affected.
Saturation is the amount of that color in a video picture. Lower settings produce less saturated colors; a setting of “0” removes that color from the image entirely. If the saturation is too high, that color will be overpowering and unrealistic.
• Gain: Adjusts the values to your preference. The contrast level of the primary color you select will be affected. Every adjustment made will reflect to the image immediately.
Noise Reduction
Reduces electrical image noise caused by different media players. The higher the value, the less the noise.
Brilliant Color
This function utilizes a new color-processing algorithm and system level enhancements to enable higher brightness while providing truer, more vibrant colors in picture. It enables a greater than 50% brightness increase in mid-tone images, which are common in video and natural scenes, so the projector reproduces images in realistic and true colors. If you prefer images with that quality, select On. Selecting Off disables Brilliant Color, and Color Temperature becomes unavailable for access at the same time.
Fast Mode
Select to turn On or Off the Fast Mode.
Light Mode
Select the Light Mode. The options are Normal, Economic, SmartEco, and LampSave.
Reset Current Picture Mode
Returns all of the adjustments you’ve made for the Picture menu to the factory preset values.
RED
BLUE
GREENYellow
CyanMagenta
35 Menu operation
Sound
Display
Mute Temporarily turns off the sound.
Volume Adjusts the sound level.
Power On/Off Ring Tone
Sets the ring tone for the projector On or Off.
Reset Audio Settings
All of the adjustments you’ve done under the Sound menu return to the factory preset values.
Aspect Ratio
There are several options to set the image's aspect ratio depending on your input signal source.
• Auto: Scales an image proportionally to fit the projector's native resolution in its horizontal or vertical width.
• Real: Projects an image as its original resolution and resizes it to fit within the display area. For input signals with lower resolutions, the projected image will be displayed in its original size.
• 4:3: Scales the picture so that it is displayed in the center of the screen with a 4:3 aspect ratio.
• 16:9: Scales an image so that it is displayed in the center of the screen with a 16:9 aspect ratio.
• 16:10: Scales an image so that it is displayed in the center of the screen with a 16:10 aspect ratio.
Wall Color
Corrects the projected picture’s color when the projection surface such as a painted wall which may not be white, the Wall Color feature can help correct the projected picture’s colors to prevent possible color difference between the source and projected pictures. There are several precalibrated colors to choose from: Light Yellow, Pink, Green, and Blue.
Overscan Adjustment
Conceals the poor picture quality in the four edges.
The greater the value, the more portion of the picture is concealed while the screen remains filled and geometrically accurate. Setting 0 means the picture is 100% displayed.
15:9 picture
4:3 picture
16:9 picture
4:3 picture
16:9 picture
16:10 picture
36 Menu operation
System Setup : Basic
3D
This projector features a 3D function which enables you to enjoy the 3D movies, videos, and sporting events in a more realistic way by presenting the depth of the images. You need to wear a pair of 3D glasses to view the 3D images.
• 3D Mode: The default setting is Off. If you want the projector to automatically choose an appropriate 3D format when detecting 3D contents, select Auto. If the projector cannot recognize the 3D format, press / to choose a 3D mode from among Top Bottom, Frame Sequential, Frame Packing and Side by Side.
When 3D function is activated:
• The brightness level of the projected image will decrease.
• The following settings cannot be adjusted: Picture Mode, Reference Mode.
• The Keystone can only be adjusted within limited degrees.
• 3D Sync Invert: When you discover the inversion of the image depth, enable this function to correct the problem.
Digital Lens Shift
Use / to vertically shift the projected image.
Language Sets the language for the On-Screen Display (OSD) menus.
Background Color
Sets the background color for the projector.
Splash Screen Allows you to select which logo screen will be displayed during projector start-up.
Projector Position
See Choosing a location on page 12.
Auto OffAllows the projector to turn off automatically if no input signal is detected after a set period of time to prevent unnecessary waste of lamp life.
Direct Power On
Allows the projector to turn on automatically once the power is fed through the power cord.
Menu Settings
• Menu Type: Switches to the Basic OSD menu.
• Menu Position: Sets the OSD menu position.
• Menu Display Time: Sets the length of time the OSD will remain active after your last key press.
• Blank Reminder Message: Sets whether the reminder message is displayed by the projector while the image is hidden.
Source Rename
Renames the current input source to your desired name.
On the Source Rename window, use / / / to set the desired characters for the connected source item.
When done, press OK to save the changes.
Auto Source Allows the projector to automatically search for a signal.
37 Menu operation
System Setup : Advanced
Light Settings• Reset Light Timer: See Timing of replacing the lamp (FOR SERVICE PERSONNEL ONLY) on page 41.
• Light Usage Time: Displays the number of hours the light has been used.
HDMI Settings
HDMI Range: Sets the HDMI Range to Auto, Full, or Limited.
Baud RateSelects a baud rate that is identical with your computer’s so that you can connect the projector using a suitable RS-232 cable and update or download the projector’s firmware. This function is intended for qualified service personnel.
Test Pattern
Adjusts the image size and focus and check that the projected image is free from distortion.
Quick CoolingSelect On enables the function and projector cooling time will be shortened from a normal 90-second duration to approximately 15 seconds.
High Altitude Mode
We recommend you use the High Altitude Mode when your environment is between 1500 m –3000 m above sea level, and ambient temperature is between 0°C–30°C.
Operation under "High Altitude Mode" may cause a higher decibel operating noise level because of increased fan speed necessary to improve overall system cooling and performance.
If you use this projector under other extreme conditions excluding the above, it may display auto shut-down symptoms, which is designed to protect your projector from over-heating. In cases like this, you should switch to High Altitude mode to solve these symptoms. However, this is not to state that this projector can operate under any and all harsh or extreme conditions.
Do not use the High Altitude Mode if your altitude is between 0 m and 1500 m and ambient temperature is between 0°C and 35°C. The projector will be over cooled, if you turn the mode on under such a condition.
Password
For security purposes and to prevent unauthorized use, you may set up password security for the projector. See Utilizing the password function for details.
• Change Password
You will be asked to enter the current password before changing to a new one.
• Power On Lock
Limits use of the projector to only those who know the correct password.
38 Menu operation
Information
Key Lock
With the control keys on the projector locked, you can prevent your projector settings from being changed accidentally (by children, for example).
When you select On to enable this function, no control keys on the projector will
function, except POWER.
To unlock the keys, press and hold on the projector for 3 seconds.
LED Indicator
When you select On, all LED indicators on the projector function normally. See Indicators for more details.
When you select Off, the LED indicators are off after you turn on the projector and the splash screen displays. However, if the projector is not working properly, the LED indicators light or flash to remind you that a problem may occur. See also Indicators for more details.
Reset All Settings
Returns all settings to the factory preset values.
The following settings will still remain: Picture, Keystone, Language, Projector Position, Menu Type, Password, Key Lock, Reset Light Timer, and High Altitude Mode.
Information
• Source: Shows the current signal source.
• Picture Mode: Shows the selected mode in the Picture menu.
• Resolution: Displays the native resolution of the input source.
• Color System: Shows input system format.
• Light Usage Time: Shows the number of hours the light has been used.
• 3D Format: Shows the current 3D mode.
• Firmware Version: Shows the firmware version of your projector.
• Service Code: Shows the service code of your projector.
39 Maintenance
Maintenance
Care of the projector
Cleaning the lensClean the lens whenever you notice dirt or dust on the surface. Please be sure to turn off the projector and let it cool down completely before cleaning the lens.
• Use a canister of compressed air to remove dust.
• If there is dirt or smears, use lens-cleaning paper or moisten a soft cloth with lens cleaner and gently wipe the lens surface.
• Never use any type of abrasive pad, alkaline/acid cleaner, scouring powder, or volatile solvent, such as alcohol, benzene, thinner or insecticide. Using such materials or maintaining prolonged contact with rubber or vinyl materials may result in damage to the projector surface and cabinet material.
Cleaning the projector caseBefore you clean the case, turn the projector off using the proper shutdown procedure as described in Shutting down the projector on page 24 and unplug the power cord.
• To remove dirt or dust, wipe the case with a soft, lint-free cloth.
• To remove stubborn dirt or stains, moisten a soft cloth with water and a neutral pH detergent. Then wipe the case.
Storing the projectorIf you need to store the projector for an extended time, please follow the instructions below:
• Make sure the temperature and humidity of the storage area are within the recommended range for the projector. Please refer to Specifications on page 45 or consult your dealer about the range.
• Retract the adjuster feet.
• Remove the battery from the remote control.
• Pack the projector in its original packing or equivalent.
Transporting the projectorIt is recommended that you ship the projector with its original packing or equivalent.
Never use wax, alcohol, benzene, thinner or other chemical detergents. These can damage the case.
40 Maintenance
Lamp information
Getting to know the lamp hourWhen the projector is in operation, the duration (in hours) of lamp usage is automatically calculated by the built-in timer. The method of calculating the equivalent lamp hour is as follows:
1. Light Usage Time = (x+y+z+a) hours, if:
Time used in Normal mode = x hours
Time used in Economic mode = y hours
Time used in SmartEco mode = z hours
Time used in LampSave mode = a hours
2. Equivalent Lamp Hour = hours
, if
X= lamp life spec of Normal mode
Y= lamp life spec of Economic mode
Z= lamp life spec of SmartEco mode
A= lamp life spec of LampSave mode
A’ is the longest lamp life spec among X, Y, Z, A
To obtain the lamp hour information:
1. Go to Advanced Menu - System Setup : Advanced > Light Settings and press OK. The Light Settings page appears.
2. Press to select Light Usage Time and press OK. The Light Usage Time information is displayed.
You can also get the Light Usage Time information on the Information menu.
When you calculate Equivalent Light Usage hour manually, it will probably have deviation from the value shown in OSD menu since projector system calculates time used for each light mode in “Minutes” then rounds down to an integer in hours shown in OSD.
For time used in each light mode shown in OSD menu:
• Time used is accumulated and rounded down to an integer in hours.
• When time used is less than 1 hour, it shows 0 hours.
A'X---- A'
Y---- y A'
Z---- z A'
A---- a+ + +=
41 Maintenance
Extending lamp life• Setting the Light Mode
Go to Advanced Menu - Picture > Advanced > Light Mode, press OK. The Light Mode page appears.
Setting the projector in Economic, SmartEco or LampSave mode extends lamp life.
• Setting Auto Power Off
This function allows the projector to turn off automatically if no input signal is detected after a set period of time to prevent unnecessary waste of lamp life.
To set Auto Power Off, go to Advanced Menu - System Setup : Basic > Auto Off and press / .
Timing of replacing the lamp (FOR SERVICE PERSONNEL ONLY)When the LIGHT indicator lights up or a message appears suggesting it is time to replace the lamp, please consult your dealer or go to http://www.BenQ.com before installing a new lamp. An old lamp may cause a malfunction in the projector and in some instances the light may explode.
The following Lamp warning displays will remind you to change the lamp.
Light Mode DescriptionNormal Provides full lamp brightnessEconomic Lowers brightness to extend the lamp life and decreases the fan noise
SmartEcoAdjusts the lamp power automatically depending on the content brightness level while optimizing display quality
LampSaveAdjusts the lamp power automatically depending on the content brightness level while offering a longer lamp life
• The apparent brightness of the projected image will vary depending on the ambient lighting conditions, selected input signal contrast/brightness settings, and is directly proportional to projection distance.
• The lamp brightness will decline over time and may vary within the lamp manufacturers specifications. This is normal and expected behavior.
• The LIGHT indicator light and TEMPerature warning light will light up if the lamp becomes too hot. Turn the power off and let the projector cool for 45 minutes. If the Light or Temp indicator still lights up after turning the power back on, please contact your dealer. See Indicators on page 43.
Install a new lamp for optimal performance. Press OK to dismiss the message.
It is strongly recommended that you replace the lamp at this age. The lamp is a consumable item. The lamp brightness diminishes with use. This is normal lamp behavior. You can replace the lamp whenever you notice that the brightness level has significantly diminished.Press OK to dismiss the message.
Order Replacement Lamp
Lamp>XXXX Hours
Order a new lamp at www.benq.com
OK
OK
Replace Lamp Soon
Lamp>XXXX Hours
Order a new lamp at www.benq.com
42 Maintenance
The lamp MUST be replaced before the projector will operate normally.Press OK to dismiss the message.
"XXXX" shown in the above messages are numbers that vary depending on different models.
OK
Out of Lamp Usage Time
Replace lamp (Refer to user manual)
Then reset lamp timer
Order a new lamp at www.benq.com
OK
Replace Lamp Now
Lamp>XXXX Hours
Order a new lamp at www.benq.com
Lamp usage time exceeded
43 Maintenance
IndicatorsLight
Status & Description
Power events
Stand-by mode
Powering up
Normal operation
Normal power-down cooling
Download
CW start fail
Lamp life exhausted
Lamp door is not closed
Burn-In events
Burn-in ON
Burn-in OFF
Lamp events
Lamp error in normal operation
Lamp is not lit up
Thermal events
Fan 1 error (the actual fan speed is outside the desired speed)
Fan 2 error (the actual fan speed is outside the desired speed)
Fan 3 error (the actual fan speed is outside the desired speed)
Temperature 1 error (over limited temperature)
Thermal IC #I2C connection error
: Off: Orange On : Green On : Red On
: Orange Flashing : Green Flashing : Red Flashing
44 Troubleshooting
Troubleshooting
The projector does not turn on.
Cause Remedy
There is no power from the power cord.
Plug the power cord into the AC power jack on the projector, and plug the power cord into the power outlet. If the power outlet has a switch, make sure that it is switched on.
Attempting to turn the projector on again during the cooling process.
Wait until the cooling down process has completed.
No picture
Cause Remedy
The video source is not turned on or connected correctly.
Turn the video source on and check that the signal cable is connected correctly.
The projector is not correctly connected to the input signal device.
Check the connection.
The input signal has not been correctly selected. Select the correct input signal with the SOURCE key.The lens cover is still closed. Open the lens cover.
Blurred image
Cause Remedy
The projection lens is not correctly focused. Adjust the focus of the lens using the focus ring.The projector and the screen are not aligned properly.
Adjust the projection angle and direction as well as the height of the projector if necessary.
The lens cover is still closed. Open the lens cover.
Remote control does not work.
Cause Remedy
The batteries are out of power. Replace both of the batteries with new ones.There is an obstacle between the remote control and the projector.
Remove the obstacle.
You are too far away from the projector. Stand within 8 meters (26 feet) of the projector.
The password is incorrect.
Cause Remedy
You do not remember the password. See Entering the password recall procedure on page 23.
45 Specifications
Specifications
Projector specifications
All specifications are subject to change without notice.
Optical
Resolution1920 x 1080 FHD
Display system1-CHIP DMD
LensF = 2.0 ~ 2.05, f = 15.843 ~ 17.445 mm
Lamp245 W lamp
Electrical
Power supplyAC100–240V, 3.8 A, 50–60 Hz (Automatic)
Power consumption340 W (Max); < 0.5 W (Standby)
Mechanical
Weight2.79 Kg (6.1 lbs)
Output terminals
Speaker10 watt x 1
Audio signal outputAudio jack x 1
Control
USBType-A power supply 5V / 1.5 A x 1
RS-232 serial control9 pin x 1
IR receiver x 2
Input terminals
Video signal inputSD/HDTV signal input
Digital - HDMI 1/MHL x 1HDMI 2 x 1
Audio signal inputAudio in
Audio jack x 1
Environmental Requirements
Operating temperature0°C–40°C at sea level
Operating relative humidity10%–90% (without condensation)
Operating altitude0–1499 m at 0°C–35°C1500–3000 m at 0°C–30°C (with High Altitude Mode on)
Storage temperature-20°C–60°C at sea level
Storage humidity10%–90% RH (without condensation)
Storage altitude30°C@ 0~12,200m above sea level
TransportingOriginal packing or equivalent is recommended
RepairingPlease visit below website and choose your country to find your service contact window. http://www.benq.com/welcome
47 Specifications
Timing chartSupported timing for HDMI (HDCP) input
• PC timings
Resolution ModeVertical
Frequency (Hz)
Horizontal Frequency
(kHz)
Pixel Frequency
(MHz)
Supported 3D formatFrame
SequentialTop
BottomSide-by-Si
de
640 x 480
VGA_60 59.940 31.469 25.175 V V VVGA_72 72.809 37.861 31.500 VGA_75 75.000 37.500 31.500 VGA_85 85.008 43.269 36.000
720 x 400 720 x 400_70 70.087 31.469 28.3221
800 x 600
SVGA_60 60.317 37.879 40.000 V V VSVGA_72 72.188 48.077 50.000 SVGA_75 75.000 46.875 49.500 SVGA_85 85.061 53.674 56.250
SVGA_120 (Reduce Blanking) 119.854 77.425 83.000 V
1024 x 768
XGA_60 60.004 48.363 65.000 V V VXGA_70 70.069 56.476 75.000 XGA_75 75.029 60.023 78.750 XGA_85 84.997 68.667 94.500
XGA_120 (Reduce Blanking) 119.989 97.551 115.5 V
1152 x 864 1152 x 864_75 75 67.5 108
1024 x 576@60Hz BenQ Notebook Timing 60.00 35.820 46.996
1024 x 600@65Hz BenQ Notebook Timing 64.995 41.467 51.419
1280 x 720 1280 x 720_60 60 45.000 74.250 V V V1280 x 768 1280 x 768_60 59.870 47.776 79.5 V V V
1280 x 800
WXGA_60 59.810 49.702 83.500 V V VWXGA_75 74.934 62.795 106.500WXGA_85 84.880 71.554 122.500
WXGA_120 (Reduce Blanking) 119.909 101.563 146.25 V
1280 x 1024SXGA_60 60.020 63.981 108.000 V VSXGA_75 75.025 79.976 135.000SXGA_85 85.024 91.146 157.500
1280 x 960 1280 x 960_60 60.000 60.000 108 V V1280 x 960_85 85.002 85.938 148.500
1360 x 768 1360 x 768_60 60.015 47.712 85.500 V V1440 x 900 WXGA+_60 59.887 55.935 106.500 V V1400 x 1050 SXGA+_60 59.978 65.317 121.750 V V1600 x 1200 UXGA 60.000 75.000 162.000 V1680 x 1050 1680 x 1050_60 59.954 65.290 146.250 V V
640 x 480@67Hz MAC13 66.667 35.000 30.240832 x 624@75Hz MAC16 74.546 49.722 57.280
1024 x 768@75Hz MAC19 75.020 60.241 80.0001152 x 870@75Hz MAC21 75.06 68.68 100.00
1920 x 1080@60Hz 1920 x 1080_60 60 67.5 148.5 V V
1920 x 1200@60Hz 1920 x 1200_60(Reduce Blanking) 59.95 74.038 154 V V
The timings showing above may not be supported due to EDID file and VGA graphic card limitations. It is possible that some timings cannot be chosen.
48 Specifications
• Video timings
Supported timing for MHL input
Timing ResolutionVertical
Frequency (Hz)
Horizontal Frequency
(kHz)
Pixel Frequency
(MHz)
Supported 3D formatFrame
SequentialFrame Packing
Top Bottom
Side-by-Side
480i 720 x 480 59.94 15.73 27 V480p 720 x 480 59.94 31.47 27 V576i 720 x 576 50 15.63 27576p 720 x 576 50 31.25 27
720/50p 1280 x 720 50 37.5 74.25 V V V720/60p 1280 x 720 60 45.00 74.25 V V V V1080/50i 1920 x 1080 50 28.13 74.25 V1080/60i 1920 x 1080 60 33.75 74.25 V1080/24P 1920 x 1080 24 27 74.25 V V V1080/25P 1920 x 1080 25 28.13 74.251080/30P 1920 x 1080 30 33.75 74.251080/50P 1920 x 1080 50 56.25 148.5 V V1080/60P 1920 x 1080 60 67.5 148.5 V V
Timing ResolutionVertical Frequency
(Hz)Horizontal
Frequency (kHz)Pixel Frequency
(MHz)480i 720 (1440) x 480 59.94 15.73 27480p 720 x 480 59.94 31.47 27576i 720 (1440) x 576 50 15.63 27576p 720 x 576 50 31.25 27
720/50p 1280 x 720 50 37.5 74.25720/60p 1280 x 720 60 45.00 74.25
1080/24P 1920 x 1080 24 27 74.251080/25P 1920 x 1080 25 28.13 74.251080/30P 1920 x 1080 30 33.75 74.251080/50i 1920 x 1080 50 28.13 74.251080/60i 1920 x 1080 60 33.75 74.251080/50p 1920 x 1080 50 56.25 148.51080/60p 1920 x 1080 60 67.5 148.5
49 Specifications
RS232 command
RS232 pin assignmentNo. Serial No. Serial
1 NC 6 NC2 RX 7 RTSZ3 TX 8 CTSZ4 NC 9 NC5 GND
Function Type Operation ASCII
PowerWrite Power On <CR>*pow=on#<CR>Write Power off <CR>*pow=off#<CR>Read Power Status <CR>*pow=?#<CR>
Source SelectionWrite HDMI(MHL) <CR>*sour=hdmi#<CR>Write HDMI 2 <CR>*sour=hdmi2#<CR>Read Current source <CR>*sour=?#<CR>
Audio Control
Write Mute On <CR>*mute=on#<CR>Write Mute Off <CR>*mute=off#<CR>Read Mute Status <CR>*mute=?#<CR>Write Volume + <CR>*vol=+#<CR>Write Volume - <CR>*vol=-#<CR>Write Volume level for customer <CR>*vol=value#<CR>Read Volume Status <CR>*vol=?#<CR>
Picture Mode
Write Bright <CR>*appmod=bright#<CR> Write Living Room <CR>*appmod=livingroom#<CR>Write Game <CR>*appmod=game#<CR>Write Cinema <CR>*appmod=cine#<CR>Write Football <CR>*appmod=football#<CR>Write User1 <CR>*appmod=user1#<CR>Write User2 <CR>*appmod=user2#<CR>Write 3D <CR>*appmod=threed#<CR>Read Picture Mode <CR>*appmod=?#<CR>
1 2 3 4 5
6 7 8 9
50 Specifications
Picture Setting
Write Contrast + <CR>*con=+#<CR>Write Contrast - <CR>*con=-#<CR>Write Set Contrast value <CR>*con=value#<CR>Read Contrast value <CR>*con=?#<CR>Write Brightness + <CR>*bri=+#<CR>Write Brightness - <CR>*bri=-#<CR>Write Set Brightness value <CR>*bri=value#<CR>Read Brightness value <CR>*bri=?#<CR>Write Sharpness + <CR>*sharp=+#<CR>Write Sharpness - <CR>*sharp=-#<CR>Write Set Sharpness value <CR>*sharp=value#<CR>Read Sharpness value <CR>*sharp=?#<CR>Write Color Temperature-Warm <CR>*ct=warm#<CR>Write Color Temperature-Normal <CR>*ct=normal#<CR>Write Color Temperature-Cool <CR>*ct=cool#<CR>Write Color Temperature-lamp native <CR>*ct=native#<CR>Read Color Temperature Status <CR>*ct=?#<CR>Write Aspect 4:3 <CR>*asp=4:3#<CR>Write Aspect 16:9 <CR>*asp=16:9#<CR>Write Aspect 16:10 <CR>*asp=16:10#<CR>Write Aspect Auto <CR>*asp=AUTO#<CR>Write Aspect Real <CR>*asp=REAL#<CR>Read Aspect Status <CR>*asp=?#<CR>Write Vertical Keystone + <CR>*vkeystone=+#<CR>Write Vertical Keystone - <CR>*vkeystone=-#<CR>Read Vertical Keystone value <CR>*vkeystone=?#<CR>Write Overscan Adjustment + <CR>*overscan=+#<CR>Write Overscan Adjustment - <CR>*overscan=-#<CR>Read Overscan Adjustment value <CR>*overscan=?#<CR>
Operation Settings
Write Brilliant color on <CR>*BC=on#<CR>Write Brilliant color off <CR>*BC=off#<CR>Read Brilliant color status <CR>*BC=?#<CR>Write Reset picture settings <CR>*rstpicsetting#<CR>Write Projector Position-Front Table <CR>*pp=FT#<CR>Write Projector Position-Rear Table <CR>*pp=RE#<CR>Write Projector Position-Rear Ceiling <CR>*pp=RC#<CR>Write Projector Position-Front Ceiling <CR>*pp=FC#<CR>Read Projector Position Status <CR>*pp=?#<CR>Write Quick cooling on <CR>*qcool=on#<CR>Write Quick cooling off <CR>*qcool=off#<CR>Read Quick cooling status <CR>*qcool=?#<CR>Write Quick auto search <CR>*QAS=on#<CR>Write Quick auto search <CR>*QAS=off#<CR>Read Quick auto search status <CR>*QAS=?#<CR>Write Menu Position - Center <CR>*menuposition=center#<CR>Write Menu Position - Top-Left <CR>*menuposition=tl#<CR>Write Menu Position - Top-Right <CR>*menuposition=tr#<CR>Write Menu Position - Bottom-Right <CR>*menuposition=br#<CR>Write Menu Position - Bottom-Left <CR>*menuposition=bl#<CR>Read Menu Position Status <CR>*menuposition=?#<CR>Write Direct Power On-on <CR>*directpower=on#<CR>Write Direct Power On-off <CR>*directpower=off#<CR>Read Direct Power On-Status <CR>*directpower=?#<CR>
Function Type Operation ASCII
51 Specifications
Baud Rate
Write 9600 <CR>*baud=9600#<CR>Write 14400 <CR>*baud=14400#<CR>Write 19200 <CR>*baud=19200#<CR>Write 38400 <CR>*baud=38400#<CR>Write 57600 <CR>*baud=57600#<CR>Write 115200 <CR>*baud=115200#<CR>Read Current Baud Rate <CR>*baud=?#<CR>
Lamp Control
Read Lamp <CR>*ltim=?#<CR>Write Normal mode <CR>*lampm=lnor#<CR>Write Eco mode <CR>*lampm=eco#<CR>Write SmartEco mode <CR>*lampm=seco#<CR>Write SmartEco mode 2 <CR>*lampm=seco2#<CR>Read Lamp Mode Status <CR>*lampm=?#<CR>
Miscellaneous
Read Model Name <CR>*modelname=?#<CR>Read System F/W Version <CR>*sysfwversion=?#<CR>Read Scaler F/W Version <CR>*scalerfwversion=?#<CR>Read MCU F/W Version <CR>*mcufwversion=?#<CR>Read Ballast F/W Version <CR>*ballastfwversion=?#<CR>Write Blank On <CR>*blank=on#<CR>Write Blank Off <CR>*blank=off#<CR>Read Blank Status <CR>*blank=?#<CR>Write Menu On <CR>*menu=on#<CR>Write Menu Off <CR>*menu=off#<CR>Read Menu Status <CR>*menu=?#<CR>Write Up <CR>*up#<CR>Write Down <CR>*down#<CR>Write Right <CR>*right#<CR>Write Left <CR>*left#<CR>Write Enter <CR>*enter#<CR>Write Back <CR>*back#<CR>Write Source Menu On <CR>*sourmenu=on#<CR>Write Source Menu Off <CR>*sourmenu=off#<CR>Read Source Menu Status <CR>*sourmenu=?#<CR>Write 3D Sync Off <CR>*3d=off#<CR>Write 3D Auto <CR>*3d=auto#<CR>Write 3D Sync Top Bottom <CR>*3d=tb#<CR>Write 3D Sync Frame Sequential <CR>*3d=fs#<CR>Write 3D Frame packing <CR>*3d=fp#<CR>Write 3D Side by side <CR>*3d=sbs#<CR>Write 3D inverter disable <CR>*3d=da#<CR>Write 3D inverter <CR>*3d=iv#<CR>Read 3D Sync Status <CR>*3d=?#<CR>
Function Type Operation ASCII