Solid State Pressure Sensor STX Series - Angst+Pfister
11
Solid State Pressure Sensor STX Series – Model 13A FEATURES Calibrated Span and Offset Multi-order Temperature compensation Fastening Mount DESCRIPTION 0.5V/4.5V or optional 3V or 5V Supply Customized Configuration upon request ANALOG OUTPUT The Series STX Model 13A is a smart pressure sensor with calibrated and amplified output. The ceramic hybrid package performs excellent isolation to external stress during operation. Digital compensation of sensor offset, sensitivity, temperature drift and nonlinearity is accomplished in factory via an internal DSP running a correction algorithm with calibration coefficients stored in on-chip EEPROM. A variety of output configuration, including resolution, sampling rate, output interface are available to provide simple and ready-to-use solution for a wide rage of application. The Series STX 13A is available for pressure range from 0.15 psi to 100 psi. Please contact factory for detail. 1 STX13A-D_1610-21567-0005-E-0817
-
Upload
khangminh22 -
Category
Documents
-
view
2 -
download
0
Transcript of Solid State Pressure Sensor STX Series - Angst+Pfister
Solid State Pressure Sensor
STX Series – Model 13A
FEATURES
Calibrated Span and OffsetMulti-order Temperature compensation
Fastening Mount
DESCRIPTION
0.5V/4.5V or optional3V or 5V SupplyCustomized Configuration upon request
ANALOG OUTPUT
The Series STX Model 13A is a smart pressure sensor with calibrated and amplified output. The ceramic hybrid package performs excellent isolation to external stress during operation. Digital compensation of sensor offset, sensitivity, temperature drift and nonlinearity is accomplished in factory via an internal DSP running a correction algorithm with calibration coefficients stored in on-chip EEPROM.A variety of output configuration, including resolution, sampling rate, output interface are available to provide simple and ready-to-use solution for a wide rage of application.The Series STX 13A is available for pressure range from 0.15 psi to 100 psi. Please contact factory for detail.
1 STX13A-D_1610-21567-0005-E-0817
Ordering Information
10-2016 V1.0
Series Type of PressureG: Gage (Port B only)H: Gage (Dual Port)A: Absolute (Port A only)D: Differential (Dual Port)
Pressure range005 = 0 ~ 5 psi
015 = 0 ~ 15 psi030 = 0 ~ 30 psi050 = 0 ~ 50 psi100 = 0 ~ 100 psi
L15 = 0 ~ 0.15 psiL30 = 0 ~ 0.3 psiL50 = 0 ~ 0.5 psiL70 = 0 ~ 0.7 psi
(belwo are Low-Pressure)
0
3
= 1-wire P+T= 0.5 to 4.5 V
= 0 to 1 V = 0.2 to 4.7 V
= 1-wire P
= 0.2 to 4.8 V 21
56
= N/A7= I2C 8
= SpecialS
= N/A4
Supply VoltageBlank = 4.75 to 5.25 VL = 2.75 to 3.33 V
007 = 0 ~ 7 psi
001 = 0 ~ 1 psi002 = 0 ~ 2 psi003 = 0 ~ 3 psi
NOTES:1. Specifying differential pressure means a ± pressure range.2. Differential pressure can be specified to a maximum of +/- 100 psi.3. Custom output, pressure range and temperature compensated range are available.4. Negative gage normally has offset (0.5V) at 0 psi and full scale output (4.5V). Reverse is also applicable.5. Accuracy may vary on pressure range6. Minimum absolute pressure that can be specified is 100 psia7. Medium is available for clean air. For other medium please contact factory.
13A L XXX G X 0 X
Series STX 13 Analog
Notes:Custom ranges and units are available upon request. Please contact factory.
X
9 = SPI
Type of Output
Option10: No special reguest97: Compensated Temp 0~85 degC
Other options available upon request.
0= same side
Leading Direction
1. Port B is used for positive differential
3. Port B is used for gage2. Port A is used for absolute
Port B
Port A
2 STX13A-D_1610-21567-0005-E-0817
NOTES:5. Wetted material: PA, RTV, Epoxy, ceramic, Au, nickel and silicon
3. Accuracy includes NOL, hysterisis, TCS and TCO over 0/50°C, BFSL definition6. Output is ratiometric to supply voltage7. Output load resistance to Vss or Vdd: 2.5KΩ (min), 10KΩ (typ)
CharacteristicsUnless otherwise specified, all parameters are measured at 3/5V, 25 °C and 60% RH
1. Supply 3V or 5V must be ordered separately.2. Smaller range and other units are also available for ordering
4. For differential, offset = 2.50V, Span = ±2.00V
Over Pressure 5
Span Output 4 Zero Output 4 Pressure Range 2
Supply Voltage 1
°C
Rated Pressure
V
V
V
PSI
Min
0.50
4.00
0
0.428
2.75
5
Temp - Compensating
Parameters
Temp - Operating
Temp - Storage
-20
-40
°C
°C
+50
3X
0.572
5.25
100
+85
+125
Typ Max Unit
Supply Current 1 mA2.5
Thermal Hysteresis 3 %FS-0.15 +0.15
Response Time ms1 2
Accuracy 3 %FS1.8
Linearity 3 %FS-0.5 +0.5
10-2016 V1.0
NOTE:1. Port B is used for positive differential
2. Port A is used for absolute
3. Port B is used for gage
4. All dimensions are mm
NOTES:N.C. pins must be left floatingA 0.1uf capacitor must be connected between VDDand VSS
* Pin out configuration may vary, refer to individual data sheetSoldering reflow: 250 °C for 5 sec max.
Dimension
Pin #
1
2
3
4
5
6
Description
VSS
N.C.
N.C.
N.C.
VDD
SIG
Top ViewBottom View
12.6
t=0.3
10.7
14
9.0
4.8
10.7
21.6
27.4
20.3
Ø3.6 SmateXXXXXX
XXXXXXX
5.35
0.552.54
5.00
Port B
Port A
3 STX13A-D_1610-21567-0005-E-0817
NOTE:1. Port B is used for positive differential
2. Port A is used for absolute
3. Port B is used for gage
4. All dimensions are mm
NOTES:N.C. pins must be left floatingA 0.1uf capacitor must be connected between VDDand VSS
* Pin out configuration may vary, refer to individual data sheetSoldering reflow: 250 °C for 5 sec max.
NOTES:
6. Wetted material: PA, RTV, Epoxy, ceramic, Au, nickel and silicon3. Accuracy includes NOL, hysterisis, TCS and TCO over 0/50°C, BFSL definition 7. Output is ratiometric to supply voltage
Dimension
8. Output load resistance to Vss or Vdd: 2.5KΩ (min), 10KΩ (typ)
CharacteristicsUnless otherwise specified, all parameters are measured at 3/5V, 25 °C and 60% RH
1. Supply 3V or 5V must be ordered separately.2. Smaller range and other units are also available for ordering
4. For differential, offset = 2.50V, Span = ±2.00V
5. Over-pressure will vary on different range
Over Pressure 5
Span Output 4 Zero Output 4 Pressure Range 2
Supply Voltage 1
°C
Rated Pressure
V
V
V
PSI
Min
0.50
4.00
0
0.412
2.75
0.15
Temp - Compensating
Parameters
Temp - Operating
Temp - Storage
-20
-40
°C
°C
+50
3X
0.588
5.25
3
+85
+125
Typ Max Unit
Supply Current 1 mA2.5
Thermal Hysteresis 3 %FS-0.15 +0.15
Response Time ms1 2
Accuracy 3 %FS2.2
Linearity 3 %FS-0.5 +0.5
9. Zeroing at installation is required
10-2016 V1.0
Pin #
1
2
3
4
5
6
Description
VSS
N.C.
N.C.
N.C.
VDD
SIG
Top ViewBottom View
12.6
t=0.3
10.7
14
9.0
4.8
10.7
21.6
27.4
20.3
Ø3.6 SmateXXXXXX
XXXXXXX
5.35
0.552.54
5.00
Port B
Port A
4 STX13A-D_1610-21567-0005-E-0817
NOTES:5. Wetted material: PA, RTV, Epoxy, ceramic, Au, nickel and silicon
3. Accuracy includes NOL, hysterisis, TCS and TCO over 0/50°C, BFSL definition6. Output is ratiometric to supply voltage7. Output load resistance to Vss or Vdd: 2.5KΩ (min), 10KΩ (typ)
CharacteristicsUnless otherwise specified, all parameters are measured at 3/5V, 25 °C and 60% RH
1. Supply 3V or 5V must be ordered separately.2. Smaller range and other units are also available for ordering
4. For differential, offset = 2.50V, Span = ±2.00V
Over Pressure 5
Span Output 4 Zero Output 4 Pressure Range 2
Supply Voltage 1
°C
Rated Pressure
V
V
V
PSI
Min
0.50
4.00
0
0.428
2.75
5
Temp - Compensating
Parameters
Temp - Operating
Temp - Storage
-20
-40
°C
°C
+85
3X
0.572
5.25
100
+85
+125
Typ Max Unit
Supply Current 1 mA2.5
Thermal Hysteresis 3 %FS-0.15 +0.15
Response Time ms1 2
Accuracy 3 %FS1.8
Linearity 3 %FS-0.5 +0.5
10-2016 V1.0
NOTE:1. Port B is used for positive differential
2. Port A is used for absolute
3. Port B is used for gage
4. All dimensions are mm
NOTES:N.C. pins must be left floatingA 0.1uf capacitor must be connected between VDDand VSS
* Pin out configuration may vary, refer to individual data sheetSoldering reflow: 250 °C for 5 sec max.
Dimension
Pin #
1
2
3
4
5
6
Description
VSS
N.C.
N.C.
N.C.
VDD
SIG
Top ViewBottom View
12.6
t=0.3
10.7
14
9.0
4.8
10.7
21.6
27.4
20.3
Ø3.6 SmateXXXXXX
XXXXXXX
5.35
0.552.54
5.00
Port B
Port A
5 STX13A-D_1610-21567-0005-E-0817
Solid State Pressure Sensor
STX Series – Model 13D
FEATURES
Calibrated Span and OffsetMulti-order Temperature compensation
Fastening Mount
DESCRIPTION
OWI, I2C or SPI Interface3V or 5V SupplyCustomized Configuration upon request
DIGITALOUTPUT
The Series CCD Model 13D is a smart pressure transducer with digital output via 1-wire serial, I2C or SPI interface. Digital compensation of sensor offset, sensitivity, temperature drift and nonlinearity is accomplished in factory via an internal DSP running a correction algorithm with calibration coefficients stored in on-chip EEPROM.A variety of output configuration, including resolution, sampling rate, output interface are available to provide simple and ready-to-use solution for a wide rage of application.The Series STX 13D is available for pressure range from 0.15 psi to 100 psi. Please contact factory for detail.
6 STX13A-D_1610-21567-0005-E-0817
Ordering Information
Series Type of PressureG: Gage (Port B only)H: Gage (Dual Port)A: Absolute (Port A only)D: Differential (Dual Port)
Sampling Rate0 = 1 kHz1 = 200 Hz2 = 40 Hz3 = 8 Hz
Pressure range005 = 0 ~ 5 psi
015 = 0 ~ 15 psi030 = 0 ~ 30 psi050 = 0 ~ 50 psi100 = 0 ~ 100 psi
L15 = 0 ~ 0.15 psiL30 = 0 ~ 0.3 psiL50 = 0 ~ 0.5 psiL70 = 0 ~ 0.7 psi
(belwo are Low-Pressure)
0
3
= 1-wire P+T= 0.5 to 4.5 V
= 0 to 1 V = 0.2 to 4.7 V
= 1-wire P
= 0.2 to 4.8 V 21
56
= N/A7= I2C 8
= SpecialS
= N/A4
Supply VoltageBlank = 4.75 to 5.25 VL = 2.75 to 3.33 V
007 = 0 ~ 7 psi
001 = 0 ~ 1 psi002 = 0 ~ 2 psi003 = 0 ~ 3 psi
NOTES:1. Specifying differential pressure means a ± pressure range.2. Differential pressure can be specified to a maximum of +/- 100 psi.3. Custom output, pressure range and temperature compensated range are available.4. Negative gage normally has offset (0.5V) at 0 psi and full scale output (4.5V). Reverse is also applicable.5. Accuracy may vary on pressure range6. Minimum absolute pressure that can be specified is 100 psia7. Medium is available for clean air. For other medium please contact factory.
13D L XXX G X 0 X
Series CCD 13 Digital
Notes:Custom ranges and units are available upon request. Please contact factory.
X
Option0: No special reguest
9 = SPI
Type of Output
10-2016 V1.0
0= same side
Leading Direction
1. Port B is used for positive differential
3. Port B is used for gage2. Port A is used for absolute
Port B
Port A
7 STX13A-D_1610-21567-0005-E-0817
NOTES:5. Wetted material: PA, RTV, Epoxy, ceramic, Au, nickel and silicon
3. Accuracy includes NOL, hysterisis, TCS and TCO over 0/50°C, BFSL definition6. Output is ratiometric to supply voltage7. Output load resistance to Vss or Vdd: 2.5KΩ (min), 10KΩ (typ)
CharacteristicsUnless otherwise specified, all parameters are measured at 3/5V, 25 °C and 60% RH
Warm-up Time
Full Scale Output 4 Zero Output 4 Accuracy 3
Resolution 3 Pressure range 2 Excitation 1
°C
ms
Hex
Hex
%FS, +1LSB
Bit
V
PSI
Min
14
±1.8
0666
3999
1
0
2.75
5
Temp - Compensating
Parameters
Temp - Operating -20 °C
50
2
100
+85
Typ Max Unit
-40 °C+125 Temp - Storage
Rated Pressure3X Over Pressure 5
Sampling Rate
Start-up Time
Hz
ms
8 1000
10
5.25
1. Supply 3V or 5V must be ordered separately.2. Smaller range and other units are also available for ordering
4. For differential pressure, offset = 2000 hex, FS = 666/3999
10-2016 V1.0
NOTE:1. Port B is used for positive differential
2. Port A is used for absolute
3. Port B is used for gage
4. All dimensions are mm
NOTES:N.C. pins must be left floatingA 0.1uf capacitor must be connected between VDDand VSS
* Pin out configuration may vary, refer to individual data sheetSoldering reflow: 250 °C for 5 sec max.
Dimension
Pin #
1
2
3
4
5
6
Description
VSS
N.C.
N.C.
N.C.
VDD
SIG
Top ViewBottom View
12.6
t=0.3
10.7
14
9.0
4.8
10.7
21.6
27.4
20.3
Ø3.6 SmateXXXXXX
XXXXXXX
5.35
0.552.54
5.00
Port B
Port A
8 STX13A-D_1610-21567-0005-E-0817
NOTES:
6. Wetted material: PA, RTV, Epoxy, ceramic, Au, nickel and silicon3. Accuracy includes NOL, hysterisis, TCS and TCO over 0/50°C, BFSL definition 7. Output load resistance to Vss or Vdd: 2.5KΩ (min), 10KΩ (typ)
CharacteristicsUnless otherwise specified, all parameters are measured at 3/5V, 25 °C and 60% RH
Warm-up Time
Full Scale Output 4 Zero Output 4 Accuracy 3
Resolution 3 Pressure range 2 Excitation 1
°C
ms
Hex
Hex
%FS, +1LSB
Bit
V
PSI
Min
±2.2
0666
3999
1
0
12
2.75
0.15
Temp - Compensating
Parameters
Temp - Operating -20 °C
50
2
3
+85
Typ Max Unit
-40 °C+125 Temp - Storage
Rated Pressure3X Over Pressure 5
Sampling Rate
Start-up Time
Hz
ms
8 1000
10
5.25
1. Supply 3V or 5V must be ordered separately.2. Smaller range and other units are also available for ordering
4. For differential pressure, offset = 2000 hex, FS = 666/3999
5. Over-pressure will vary on different range
8. Zeroing at installation is required
10-2016 V1.0
NOTE:1. Port B is used for positive differential
2. Port A is used for absolute
3. Port B is used for gage
4. All dimensions are mm
NOTES:N.C. pins must be left floatingA 0.1uf capacitor must be connected between VDDand VSS
* Pin out configuration may vary, refer to individual data sheetSoldering reflow: 250 °C for 5 sec max.
Dimension
Pin #
1
2
3
4
5
6
Description
VSS
N.C.
N.C.
N.C.
VDD
SIG
Top ViewBottom View
12.6
t=0.3
10.7
14
9.0
4.8
10.7
21.6
27.4
20.3
Ø3.6 SmateXXXXXX
XXXXXXX
5.35
0.552.54
5.00
Port B
Port A
9 STX13A-D_1610-21567-0005-E-0817
NOTES:
6. 1X for 1003. Accuracy includes NOL, hysterisis, TCS and TCO over 0/50°C, BFSL definition 7. The factory setting for I2C slave address is 0x28
CharacteristicsUnless otherwise specified, all parameters are measured at 3/5V, 25 °C and 60% RH
1. Supply 3V or 5V must be ordered separately.2. Smaller range and other units are also available for ordering
4. For differential pressure, offset = 2000 hex, FS = 666/3999
Output Lo-Level Voltage High Level Voltage Low Level
Accuracy 3
Resolution 3 Pressure range 2 Excitation 1
°C
VDDA
VDD
VDD
%FS, +1LSBBitPSI
Min
121.8
01
0
0.8
5
Temp - Compensating
Parameters
Temp - Operating -20 °C50
0.1
0.2
100
+85
Typ Max Unit
-40 °C+125 Temp - StorageRated Pressure3X Over Pressure 6
Update Rate
SCL clocking
ms
KHz
1
100
125
400System Freq MHZ1
Full Scale Output 4 Zero Output 4
HexHex0666
3999
2.75 5.25
10-2016 V1.0
5. Minimum pull-up on SDA and SCL is 1KΩ
NOTE:1. Port B is used for positive differential
2. Port A is used for absolute
3. Port B is used for gage
4. All dimensions are mm
NOTES:N.C. pins must be left floatingA 0.1uf capacitor must be connected between VDDand VSS
* Pin out configuration may vary, refer to individual data sheetSoldering reflow: 250 °C for 5 sec max.
Dimension
Pin #
1
2
3
4
5
6
Description
GND
SDA
SCL
N.C.
SUP
N.C.
Top ViewBottom View
12.6
t=0.3
10.7
14
9.0
4.8
10.7
21.6
27.4
20.3
Ø3.6 SmateXXXXXX
XXXXXXX
5.35
0.552.54
5.00
Port B
Port A
8. Wetted material: PA, RTV, Epoxy, ceramic, Au, nickel and silicon
10 STX13A-D_1610-21567-0005-E-0817
Experts on Design-Infor sensors and power solutions
Scan here and get an overview of personal contacts!
sensorsandpower.angst-pfister.com
We are here for you. Addresses and Contacts.
Headquarter Switzerland:
Angst+Pfister Sensors and Power AG
Thurgauerstrasse 66CH-8050 Zurich
Phone +41 44 877 35 [email protected]
Office Germany:
Angst+Pfister Sensors and Power Deutschland GmbH
Edisonstraße 16D-85716 Unterschleißheim
Phone +49 89 374 288 87 [email protected]
