Selective Laser Sintering of Filled Polymer Systems
12
Physics Procedia 83 (2016) 991 – 1002 Available online at www.sciencedirect.com 1875-3892 © 2016 Published by Elsevier B.V. This is an open access article under the CC BY-NC-ND license (http://creativecommons.org/licenses/by-nc-nd/4.0/). Peer-review under responsibility of the Bayerisches Laserzentrum GmbH doi:10.1016/j.phpro.2016.08.104 ScienceDirect a Institute of Polymer Technology, Am Weichselgarten 9, 91058 Erlangen b Collaborative Research Center 814 – Additive Manufacturing, Am Weichselgarten 9, 91058 Erlangen Keywords: E-mail address: © 2016 Published by Elsevier B.V. This is an open access article under the CC BY-NC-ND license (http://creativecommons.org/licenses/by-nc-nd/4.0/). Peer-review under responsibility of the Bayerisches Laserzentrum GmbH
-
Upload
khangminh22 -
Category
Documents
-
view
1 -
download
0
Transcript of Selective Laser Sintering of Filled Polymer Systems
Physics Procedia 83 ( 2016 ) 991 – 1002
Available online at www.sciencedirect.com
1875-3892 © 2016 Published by Elsevier B.V. This is an open access article under the CC BY-NC-ND license (http://creativecommons.org/licenses/by-nc-nd/4.0/).Peer-review under responsibility of the Bayerisches Laserzentrum GmbHdoi: 10.1016/j.phpro.2016.08.104
ScienceDirect
aInstitute of Polymer Technology, Am Weichselgarten 9, 91058 Erlangen bCollaborative Research Center 814 – Additive Manufacturing, Am Weichselgarten 9, 91058 Erlangen
Keywords:
E-mail address:
© 2016 Published by Elsevier B.V. This is an open access article under the CC BY-NC-ND license (http://creativecommons.org/licenses/by-nc-nd/4.0/).Peer-review under responsibility of the Bayerisches Laserzentrum GmbH
992 Katrin Wudy et al. / Physics Procedia 83 ( 2016 ) 991 – 1002
Katrin Wudy et al. / Physics Procedia 83 ( 2016 ) 991 – 1002 993
3.1. Material
3.2. Powder Characterization
994 Katrin Wudy et al. / Physics Procedia 83 ( 2016 ) 991 – 1002
3.3. Processing and specimen characterization
3.3.1. Processing
ss
LD hv
PE
3.3.2. Test specimen
Katrin Wudy et al. / Physics Procedia 83 ( 2016 ) 991 – 1002 995
3.3.3. Specimen characterization
4.1. Powder Properties
996 Katrin Wudy et al. / Physics Procedia 83 ( 2016 ) 991 – 1002
Katrin Wudy et al. / Physics Procedia 83 ( 2016 ) 991 – 1002 997
998 Katrin Wudy et al. / Physics Procedia 83 ( 2016 ) 991 – 1002
4.2. Specimen Properties
Katrin Wudy et al. / Physics Procedia 83 ( 2016 ) 991 – 1002 999
1000 Katrin Wudy et al. / Physics Procedia 83 ( 2016 ) 991 – 1002
Katrin Wudy et al. / Physics Procedia 83 ( 2016 ) 991 – 1002 1001
enerative Fertigungsverfahren : Rapid Prototyping - Rapid Tooling - Rapid Manufacturing.Selektives Lasersintern (SLS) mit Kunststoffen - Technologie, Prozesse und Werkstoffe.
Macromolecular Materials and Engineering60th Anual Technical Conference of the Society of Plastic
Engineers (ANTEC), San Francisco, CaliforniaPraxis der thermischen Analyse von Kunststoffen.
Assembly AutomationAIP Conference Proceedings
Procedia Engineering
DDMC ProceedingsWerkstoffverhalten und Prozessanalyse beim Laser-Sintern von Thermoplasten
Materials & Design
1002 Katrin Wudy et al. / Physics Procedia 83 ( 2016 ) 991 – 1002
Mat Sci Eng a-Struct
Modern techniques in applied molecular spectroscopy.
Physics Procedia
Physics Procedia
