Rear Ventilated Facades - EJOT

Rear Ventilated FacadesScrews, Facade Anchors, Insulation support anchors

2

Rear ventilated facades

ImprintPublisher:

EJOT Baubefestigungen GmbH

57334 Bad Laasphe

Layout and realisation:

EJOT Baubefestigungen GmbH

57334 Bad Laasphe

Legal Notes

EJOT products undergo continuous further development.

Technical specifications, ranges and prices are subject to

changes. For the latest information about our products,

please visit our online shop at www.ejot.de/bau

During planning and use of our products, please comply with

the accepted rules of technology, construction legislation

and the relevant safety regulations. The approvals granted by

the building authorities for our products can be downloaded

from www.ejot.com.

General terms and conditions:

Our general terms and conditions can also be found at www.

ejot.com (footer: Terms & Conditions)

©2019 by EJOT Baubefestigungen GmbH

EJOT®, ejotherm®, Delta PT® und PT® are registered trade-

marks of EJOT GmbH & Co. KG.

CRONIMAKS®, Corremaks®, EJOFAST®, Dabo®, ECOmate®

FR-variotool® and Solar Ready® are registered trademarks of

EJOT Building Fasteners GmbH.

SDS plus® is a registered trademark of Robert Bosch GmbH.

DEKTITE® is a registered trademark of Deks Industries Pty.

Ltd.

TORX® is a registered trademark of Acument Intellectual

Properties, LLC.

3

Rear ventilated facades

Screws

Insulation support anchors

Facade anchors and nylon anchors

4

The Fastener.

www.ejot.com

Horizontal and vertical:

CROSSFIX®

www.ejot.com

CROSSFIX® Facade system The flexbile substructure system made of A4 stainless steel

CROSSFIX® is the first 100% A4 stainless steel substructure for horizontal and vertical support profiles. Increase your flexibility, facilitate the assembly and save precious time and storage costs. With the CROSSFIX® system, you get everything from one supplier – in proven EJOT quality.

www.ejot.com 5

Rear ventilated facadesSelf-drilling screws

Application range l To form floating and fixed points on subst-

ructures of rear-ventilated facades

l Fastening pre-drilled stainless steel or alu-

minium wall brackets to aluminium support

profiles

l For component assemblies from 3.1 – 5.0

mm (component I + component II)

Characteristics l A2 or A4 stainless steel

NoteComponent assemblies checked with Rm

(component II) ≥ 190, ≥ 215 and ≥ 245 N/mm2.

For bearing values, please refer to the general

building authorities test certificate (abP) P-

BWU02-1980001.

EJOT® self-drilling screw JT4-3H/5-5.5x19 EJOT® self-drilling screw JT9-3H/5-5.5x19

Technical specifications

Diameter 5.5 mm

Drilling capacity 3.0 mm

Drive Hexagon A/F8

Flange head Ø 13 mm

Length non-threaded part 5.0 mm

Length [mm]

Price/100[EUR]

Order description Article number EAN

JT4 made of A2 stainless steel

19 500 JT4-3H/5-5.5x19 7 380 540 300 4061245014289

19 100 JT4-3H/5-5.5x19 VE100 6 380 540 300 4061245014876


19 500 JT9-3H/5-5.5x19 7 380 540 340 4061245014272

19 100 JT9-3H/5-5.5x19 VE100 6 380 540 340 4061245014869

Possible component assemblies

Component I [mm]

Component II [mm]

Rm support profile/

Wall bracket

1.5(stainless steel)

1.6

≥ 190 N/mm22.0

2.4

3.0(aluminium)

1.6≥ 190 N/mm2

2.0

P-BWU02-1980001

5 mm

AF8SCAN

TOSHOP

www.ejot.com6


Application range l To form floating and fixed points on sub-

structures of rear-ventilated facades

l Fastening pre-drilled stainless steel or alu-

minium wall brackets to aluminium support

profiles

Characteristics l One screw for all part combinations

l Sliding washer E14, Ø 14 mm

l Buffer zone between the screw head and

sliding disk prevents excessive clamp load

of the joint.

l Pre-assembled captive sliding washer

l Consistently low contact pressure prevents

stick-slip phenomenon

l No stripping / destruction of the thread in

component II resulting in high tensile load-

ing capacity

l High tensile and transverse load transmis-

sion in component II due to fine pitch thread

l General building authorities test certificate

(abP) as proof of usability according to DIN

18516-1 (also available as informal English

translation)

l Case hardened drill point of the JT6 version

for fastening in steel support profiles (not

part of the abP)

l Wall brackets made of stainless steel and

aluminium are part of the abP

l Buffer zone serves as visual set control

l Same assembly concept for floating and

fixed points

NoteComponent assemblies checked with Rm

(component II) ≥ 190, ≥ 215 and ≥ 245 N/mm2.

For bearing values, please refer to the general

building authorities test certificate (abP) P-

BWU02-178006.

EJOT® self-drilling screw JT6-2/5-5.0 VARIO EJOT® self-drilling screw JT9-2/5-5.0 VARIO

Length [mm]

Price/100[EUR]


JT6 made of A4 stainless steel with hardened steel drill point

30 500 JT6-2/5-5.0x30 Vario 3 598 077 991 4061245014999

30 100 JT6-2/5-5.0x30 Vario VE100 6 598 077 991 4061245021904


25 500 JT9-2/5-5.0x25 Vario 3 500 777 490 4061245020686

25 100 JT9-2/5-5.0x25 Vario VE100 6 500 777 490 4061245021508


Diameter 5.0 mm

Drilling capacity 3.0 mm

Drive Hexagon A/F8

Possible part combinations

Component I [mm]

Component II [mm]

Rm support profile/

Wall bracket


2.0

≥ 190 N/mm2

2.5

3.0


2.0

2.5

3.0


2.0

2.5

3.0

2.0(aluminium)

2.0

2.5

3.0

3.0(aluminium)

2.0

2.5

3.0

4.0(aluminium)

2.0

2.5

3.0

5.0(aluminium)

2.0

2.5

3.0

Watch the video now: https://youtu.be/pXs-bv1N3dA

P-BWU02-178006

AF8SCAN

TOSHOP

www.ejot.com 7


Visual set control by correct compression of the buffer zone

Pre-assembled captive sliding washer with buffer zone

Drive hexagon A/F 8

Large collar prevents rubbing of thread flanks in the slotted hole of the wall bracket. No stripping or destruction of the thread in component II

Low pitch allows precise com-pression of the buffer zone and high self-locking of the screw in component II

Extreme drilling speed even at low axial pressure

Fine pitch thread creates load bearing thread in component II

Recommended accessories

EJOT® A/F8-Vario Tool Article No. 9 152 900 000

Cordless metal screwdriver ASCS 6.3 Select Article No. 9 150 200 003

www.ejot.com8


The LT system for facadesForcing tension under control: The LT fastening system with plastic sleeves specifi-cally matched to the screws ensures optimum fastening of the cladding panels. The LT screws can be combined with suitable centring bushes - adapted to every application.

Head diameter 16 mm to cover slotted holes and large pre-drill diameters

DriveHexalobular TX25

XT version with cutting ring: Protective film of the facade panel is cut in and can be removed completely after assembly

Centring bushes to form fixed points...

and floating points

Very flat screw head for aesthe-tic facade design

Optionally with free spin zone for a defined low

clamp load

Processing tipWobble-free fastening when using the LT/STS Tool

www.ejot.com 9


Screw type

JT4-LT- 3-5.5x25

KD16

JF3-LT-2-5.5x30

KD16

JT4-LT-XT-3H/4-5.5x19

KD16

JT4-LT-XT-3H/6-5.5x25

KD16

JT3-LT-3-5.5x30

KD16

JT4-LT-2/6-6x50

KD16

Material A2 stainless steelA2 stainless steel

with hardened steel point1)

A2 stainless steel A2 stainless steelA2 stainless steel

with hardened steel drill point

A2 stainless steel

Application2) all common cladding panels

all common cladding panels

Aluminium panels≥ 2.0 mm

Aluminium composite panels4.0 mm



Free spin zone3) - - 4.0 mm 6.0 mm - -

For substructures made of

Aluminium Steel / aluminium Aluminium Aluminium Steel / aluminium Timber

Drilling capacity(tI pre-drilled) tII

1.5 - 3.0 mm 0.4 - 1.5 mm 1.5 - 3.0 mm 3.0 mm 1.5 - 2.5 mm 1.5 - 2.0 mm

Clamp thickness tfix 1 - 15 mm 1 - 15 mm 2 - 3 mm 4 - 5 mm 1 - 15 mm 2 - 19 mm

abP / ETA ETA-10/0200 ETA-10/0200 - P-S 18 0447 ETA-10/0200 ETA-10/0200

Centring bushes / XT centring bushes

Centring bushesØ 11/4Ø 11/6Ø 11/8


Centring bushesØ 11/2

XT centring bushesØ11/4


Centring bushesØ 11/2Ø 11/4Ø 11/6Ø 11/8

1) JF screw requires more axial pressure than JT screw with classic cutting bit in order to penetrate component II. Without swarf: Contrary to conventional self-drilling screws with classic cutting bit, ribbon swarfs, spiral swarfs or spiral swarf pieces are avoided during assembly.

2) Remark: Please note the respective approval of the facade panel and the assembly instructions of the manufacturer.3) Free spin zone: Screws without free spin zone must be loosened by 90 degrees after connecting surface in order to ensure reliable sliding.

Product finder LT system

www.ejot.com10


Application range l For fixing facade panels to 1.5-3.0 mm

aluminium substructures

l Can be combined with LT fixed and floating

point sleeves

Characteristics l A2 stainless steel

l Pan head

Benefits l To cover slotted holes and large pre-drill

diameters

l Also available in RAL lacquering

l Flat screw head for aesthetic facade design

l Wobble-free fastening by using the LT tool

NotePlease note the respective approval of the

facade panel and the assembly instructions of

the manufacturer.

Processing information for floating points on cladding panelsStop fastening as soon as the screw head con-

nects to the surface and turn the screw back a

quarter turn in order to remove the clamp load

from the connection.

EJOT® self-drilling screw JT4-LT-3-5.5x25


Diameter 5.5 mm

Drilling capacity (tI pre-drilled) + tII 1.5-3.0 mm

Drive Hexalobular TX25

Head diameter 16 mm

Head height 2.0 mm

Length [mm]

max. panel thickness [mm]

Price/100[EUR]


25 12 500 JT4-LT-3-5.5x25 KD16 7 384 207 300 4061245014029

16 mm

ETA-10/0200

SCANTO

SHOP

TX25

www.ejot.com 11


Application range l For fixing facade panels to 1.0-2.0 mm alu-

minium substructures without swarfs


point sleeves

Characteristics l A2 stainless steel with hardened steel drill

point

l Pan head


diameters




l Fastening without swarf*



the manufacturer.

AttentionJF screw requires more axial pressure than JT

screw with classic cutting bit in order to pen-

etrate component II.





EJOFAST® self-drilling screw JF3-LT-2-5.5


Diameter 5.5 mm

Drilling capacity (tI pre-drilled) + tII 1.5 mm


Head diameter 16 mm

Head height 2.0 mm

Length [mm]


Price/100[EUR]


30 10 500 JF3-LT-2-5.5x30 KD16 7 384 212 301 4061245014005

16 mm

ETA-10/0200

*Without swarfmeans that - contrary to conven-tional self-drilling screws with classic cutting bit - ribbon swarfs, spiral swarfs or spiral swarf pieces are avoided.

SCANTO

SHOP

TX25

www.ejot.com12


Application range l For fastening facade panels to aluminium

substructures ≤ 2.0 mm, for example

Novelis ff2®


point sleeves


l Pan head


diameters




l Easy assembly and reliable sliding thanks to

optimised free spin zone

l Centring bush collar protects the surface of

the facade panel from scratches

l No rivet installation gauge or drilling gauge

necessary

l XT cutting ring under the screw head fa-

cilitates easy removal of the protective film

during the forming of fixed points without

centring bush

l Thread-free part under the screw head

allows an intentional further rotation of the

screw head after connecting surface



the manufacturer.

EJOT® self-drilling screw JT4-LT-XT-3H/4-5.5x19


Diameter 5.5 mm



head diameter 16 mm

Head height 2.0 mm

Free spin zone 4 mm

Pre-drilling diameter sleeves 11 mm

Length [mm]

max. panel thickness

[mm]

Price/100[EUR]


Self-drilling screw

19 2 - 3 500 JT4-LT-XT-3H/4-5.5x19 KD16 7 384 219 300 4061245044507

Centring bushes

- 2 - 3 500 Centring bush Ø 11/2 F 3 010 005 700 4061245010212

- 2 - 3 500 Centring bush Ø 11/2 S 3 010 006 700 4061245018508

16 mm

NEW

SCANTO

SHOP

TX25

www.ejot.com 13


16 mm

Application range l For fastening plain aluminium composite

panels to aluminium substructures

l Can be combined with XT fixed and floating

point sleeves


l Pan head


diameters



l Easy assembly and reliable sliding thanks to

optimised free spin zone

l Regulated by the building authorities in test

certificate P-S 18 0447

l Easy removal of protective film

l Centring bush collar protects the surface of

the facade panel from scratches

l No rivet installation gauge or drilling gauge

necessary



screw head after connecting surface



the manufacturer.

EJOT® self-drilling screw JT4-LT-XT-3H/6-5.5x25


Diameter 5.5 mm



Head diameter 16 mm

Head height 2.0 mm

Free spin zone 6.0 mm

Pre-drilling diameter sleeves 11 mm

Length [mm]

max. panel thickness onto

timber / aluminium [mm]

Price/100[EUR]


Self-drilling screw

25 500 JT4-LT-XT-3H/6-5.5x25 KD16 7 384 216 300 4061245044538

Centring bushes

- 4 500 XT centring bush Ø11/4 F 3 010 013 700 4061245044552

- 4 500 XT centring bush Ø11/4 S 3 010 014 700 4061245044545

Assembly of the XT system1. Place XT centring bush in pre-

drilled facade panel2. Rotate XT centring bush with

LT-XT tool in order to cut the protective film

3. Fasten LT-XT screw with LT-XT tool in support profile

4. Remove protective film gently over the fixing point

NEW

P-S 18 0447

1 2

3 4

SCANTO

SHOP

TX25

www.ejot.com14


Application range l Fastening facade panels to 1.5-2.5 mm

aluminium and steel substructures


point sleeves

Characteristics l A2 stainless steel with hardened drill point

l Pan head


diameters






the manufacturer.





EJOT® self-drilling screw JT3-LT-3-5.5x30


Diameter 5.5 mm

Drilling capacity (tI pre-drilled) + tII 1.5 - 2.5 mm


Head diameter 16 mm

Head height 2.0 mm

Length [mm]


Price/100[EUR]


30 12 500 JT3-LT-3-5.5x30 KD16 7 384 211 301 4061245014012

16 mm

ETA-10/0200

SCANTO

SHOP

TX25

www.ejot.com 15


Application range l Fastening facade panels to aluminium or

timber substructures


point sleeves


l Pan head


diameters



l No pre-drilling of the timber substructure

l Good drilling behaviour even in areas of

branches




the manufacturer.





EJOT® self-drilling screw JT4-LT-2/6-6.0x50


Diameter 6.0 mm



Head diameter 16 mm

Head height 2.0 mm

Length non-threaded part 6.0 mm

Length [mm]

max. panel thickness onto timber / aluminium

[mm]

Price/100[EUR]


50 10 / 26 500 JT4-LT-2/6-6.0x50 KD16 7 384 206 300 4061245014036

16 mm

ETA-10/0200

SCANTO

SHOP

TX25

www.ejot.com16

Rear ventilated facadesCentring bushes

Application range l Fastening facade panels in combination

with LT screws with head diameter 16 mm

l To form fixed points

Characteristics l Grey coloured plastic

l For panel thickness 2 / 4 / 6 / 8 mm

l UV-resistant

Benefits l All holes in the panel are produced with the

same diameter (11 mm), which can be done

efficiently at the shop floor

l No rivet installation gauge, no drilling gauge

necessary

l Fast assembly in combination with LT screws

l Easily revisionable panel fastening

l The 0.5 collar of the bush prevents direct

contact between screw head and panel

surface

l The hole in the middle serves for the cen-

tered

positioning of the screw

NoteUsability of bushes and LT screws must be

agreed with the respective panel manufacturer.

Please note the respective approval of the


the manufacturer.

EJOT® centring bush F (fixed point)

Panel thickness [mm]

Price/100[EUR]


2 500 Centring bush Ø 11/2 F 3 010 005 700 4061245010212

4 500 Centring bush Ø 11/4 F 3 010 009 700 4061245018478

6 500 Centring bush Ø 11/6 F 3 010 011 700 4061245018454

8 500 Centring bush Ø 11/8 F 3 010 007 700 4061245018492


Bush internal hole Ø 5.8 mm

Facade panel drill hole Ø 11.0 mm

NEW

SCANTO

SHOP

www.ejot.com 17

Rear ventilated facadesCentring bushes

Application range l Fastening facade panels in combination

with LT screws with head diameter 16 mm

l To form floating points

Characteristics l Black coloured plastic

l For panel thickness 2 / 4 / 6 / 8 mm

l UV-resistant

Benefits l All holes in the panel are produced with the

same diameter (11 mm), which can be done

efficiently at the shop floor

l No rivet installation gauge, no drilling gauge

necessary

l Fast assembly in combination with LT screws

l Easily revisionable panel fastening

l The 0.5 collar of the bush prevents direct

contact between screw head and panel

surface, thus no scratches on the panel

surface even during thousandfold relative

displacement

l The bottom of the bush which is only 0.3 mm

thin is abraded due to relative displacement

l The hole in the middle serves for the cen-

tered

positioning of the screw

NoteUsability of bushes and LT screws must be

agreed with the respective panel manufacturer.

Please note the respective approval of the


the manufacturer.

Processing information for screws with full threadStop fastening as soon as the screw head con-




EJOT® centring bush S (floating point)

Panel thickness [mm]

Price/100[EUR]


2 500 Centring bush Ø 11/2 S 3 010 006 700 4061245018508

4 500 Centring bush Ø 11/4 S 3 010 010 700 4061245018461

6 500 Centring bush Ø 11/6 S 3 010 012 700 4061245018447

8 500 Centring bush Ø 11/8 S 3 010 008 700 4061245018485


Bush internal hole Ø 8.6 mm

Facade panel drill hole Ø 11.0 mm

NEW

SCANTO

SHOP

www.ejot.com18


Application range l Fastener for ALUCOBOND® external wall

cladding according to Z-10.3-774

l For fastening without forcing tension to 2

mm aluminium substructures


l With centring bush to form floating points

Benefits l Centred drilling and simultaneous fastening

of the boards to the substructure

l No pre-drilling of the substructure



screw head after surface connection

NoteWe recommend the tapered special bit

hexalobular TX25W-1/4“/Cx25 for force fit in

the fastener head. To form fixed points, we

recommend pre-drilling a Ø 4.0 mm hole in the

panel.

EJOT® self-drilling screw JT4-FR-2H/6-4.8


Diameter 4.8 mm

Drilling capacity tI + tII 1.0 + 3.0 mm


Head diameter 12 mm

Head height 3.4 mm

Ø drill hole centring bush 8.5 mm

Length [mm]

[mm]

Price/100[EUR]


Self-drilling screw

22 6 1,000 JT4-FR-2H/6-4.8x22* 7 384 170 300 4061245014050

Centring bush

- - 500 Centring bush 3 010 003 700 4061245010205

*JT9 made of A4 stainless steel upon request

Z-10.3-774

SCANTO

SHOP

TX25

www.ejot.com 19


Application range l Fastener between the reinforcing profile

and an ALUCOBOND® cassette according to

Z-10.3-774


Benefits/Operating principle l Fastener pierces the ALUCOBOND panel

and the aluminium substructure



screw head after surface connection

l Cutting ring under the screw head cuts pro-

tective film on the facade panel

l Protective film can be removed from the

ALUCOBOND® panel without residue after

assembly

l Also available as laquered version

EJOT® self-drilling screw JT4-XT


Diameter 6.0 mm

Drilling capacity tI + tII 2.0 mm


Head diameter 11 mm

Head height 2.5 mm

Free spin zone 6.0 mm

Length [mm]

For panel thickness [mm]

Price/100[EUR]


21 4.0 500 JT4-XT-3/6-6.0x21 7 384 213 300 4061245013992

Watch the video now: https://youtu.be/RKUPO7xTQ8c

Z-10.3-774

SCANTO

SHOP

TX25

www.ejot.com20


Application range l Fastening timber laths

to aluminium substructure ≤ 2 mm


l Countersunk head with milling ribs

EJOT® self-drilling screw JT4-S-2-4.8


Diameter 4.8 mm



Installation rotation speed max. 1800 rpm

Length [mm]

For timber thickness [mm]

Price/100[EUR]


38 20 - 30 500 JT4-S-2-4.8x38 7 382 086 300 4061245014197

48 30 - 40 500 JT4-S-2-4.8x48 7 382 072 300 4061245014203

Application range l Fastening plaster-base sheeting to alu-

minium substructures ≤ 3 mm


l Countersunk head with flange

Benefits l Very flat head

l Wobble-free fastening with

LT-STS Tool

EJOT® self-drilling screw JT4-STS-3-4.8


Diameter 4.8 mm


Head diameter 12 mm


Length [mm]

For panel thickness [mm]

Price/100[EUR]


35 0 - 25 500 JT4-STS-3-4.8x35 7 384 094 300 4061245014074

P-BWU02-168012

SCANTO

SHOP

SCANTO

SHOP

TX25

TX25

www.ejot.com 21

Rear ventilated facadesFacade anchors

Range of lengths anchorswith screws made of steel with zinc-plated Cr(VI)-free coating (-V) or made of A4 stainless steel

Anchor typeSDF-S

8VSDF-KB

8VSDF-S

10VSDF-KB

10VSDF-S10H

SDF-KB10H

SDF-S14A

SDF-KB14A

SDP-S10G

SDP-KB10G

Material -V -E -V -E -V -E -V -E -V -E -V -E -V -E -V -E -V -E -V -E

Length [mm]

50 • • •

60 • • • •

70 • • •

80 • • • • • • • • • • • • • •

100 • • • • • • • • • • • • • •

120 • • • • • • • • • • • • •

140 • • • • • • • • • • • • •

160 • • • • • • • • • • • • •

180 • • • • • • • • • • • • •

200 •1) •1) • • • • • • • • •1) • •1)

220 •1) •1) • • • • • • • • •1) • •1)

240 • • •1)

260 • • •

280 • • •1)

300 • • •

320 •

340 •

360 •

1) Delivery time upon request

Approval ETA-15/0387 ETA-10/0305 ETA-15/0027 ETA-12/0502

Anchor type SDF-8V SDF-10V SDF-10H SDF-14A SDP-10G

Nominal drill diameter dnom / dD [mm] 8 10 10 14 10

Drill cut diameter dcut [mm] ≤ 8.45 10.45 10.45 14.5 10.45

Drill hole depth h1 / t [mm] ≥ 60 50 / 60 80 80 80

Embedment depth (concrete + masonry) hnom / hv [mm] ≥ 50 – 70 70 70

Embedment depth (concrete) hnom,1 / hv [mm] ≥ 50 40 70 70 70

Embedment depth (masonry) hnom,2 / hv [mm] ≥ 50 50 70 70 70

Hole diameter of the component to be installed df [mm] 8.5 10.5 10.5 14.5 10.5

Building materials Standard SDF-8V SDF-10V SDF-10H SDF-14A SDP-10G

Standard concrete ≥ C12/15 DIN 1045 EN 12 • • • •

Solid brick Mz EN 77-1-001 DIN EN 772 • • • •

Vertically perforated brick Hlz EN 771-1-002 DIN 105-1 • •

Vertically perforated brick LHlz1) DIN 105-2 •

Solid sand-lime brick KS EN 771-2-009 DIN 106 (•) • • •

Perforated sand-lime brick KSL EN 771-2-003 DIN 106 • •

Slag brick 1) DIN 398

Lightweight concrete cavity block ≥ HBL 2 EN 771-3-005 DIN 18151 • •

Solid lightweight concrete bricks DIN 18152 (•) •

Solid concrete brick1) EN 771-3-006 DIN 18153 (•) •

Concrete cavity block1) DIN 18153

Concrete rain screen ≥ C 12/15 DIN 1045 •

Aerated concrete EN 771-4 DIN 1053 / 4165 • • •

1) As a rule: pull-out tests on the structureNote: Please observe the corresponding approvals for determining the characteristic load-carrying capacity.

www.ejot.com22


Application range l The cost-effective alternative for embedding

timber substructures to solid brick masonry

and concrete

Characteristics l Countersunk head

l Small drill-hole diameter

l Product identification through different

sleeve colours

NoteFor planning and processing, please observe

ETA-15/0387

EJOT® facade anchor SDF-S-8V

Characteristic values

Diameter 8.0 mm


Drill hole depth ≥ h1 60 mm

Embedment depth ≥ hnom 50 mm

Anchor length L [mm]

Fasteningthickness tfix ≤

[mm]

Price/100[EUR]


Anchors with steel screws with zinc-plated Cr(VI)-free coating (-V)

80 30 100 SDF-S-8Vx80-V 8 569 080 430 4061245019123

100 50 50 SDF-S-8Vx100-V 8 569 100 430 4061245019116

120 70 50 SDF-S-8Vx120-V 8 569 120 430 4061245019109

140 90 50 SDF-S-8Vx140-V 8 569 140 430 4061245019093

160 110 50 SDF-S-8Vx160-V 8 569 160 430 4061245019086

180 130 50 SDF-S-8Vx180-V 8 569 180 430 4061245019079

200 150 50 SDF-S-8Vx200-V* 8 569 200 430 4061245019062

220 170 50 SDF-S-8Vx220-V* 8 569 220 430 4061245019055

* Delivery time upon request

Instructions for using galvanic zinc-plated facade anchor screws (excerpt from ETA-15/0387) The special screw made of galvanic zinc-plated

steel may also be used outside, after careful

installation and if the area of the screw head

is protected against moisture and driving rain

in such a way, that no moisture can enter the

anchor shaft. This requires facade cladding or

a rain screen fixed in front of the screw head

and the screw head has to be coated with a

soft-plastic, permanently elastic, bitumen oil

combination coat (e.g. car underbody coating

or cavity protection).

Characteristic loads*

Tensile strength NRk,p in concrete < C16/20 4.50 kN

Tensile strength NRk,p in concrete ≥ C16/20 6.50 kN

Brick Mz 28-1.8, NF 2.50 kN

Solid lime sand brick KS, NF 20-2.0 2.00 kN

Transverse strength VRk,s

Anchor with steel screw 5.30 kN

Bending moment MRk,s

Anchor with steel screw 8.20 Nm

*applies to temperature range 30-50 °C / 50-80 °C

ETA-15/0387

TX30SCAN

TOSHOP

www.ejot.com 23


Application range l For the embedment of metal substructures

in solid brick masonry and concrete

Characteristics l Hexagon head with flange

l Small drill-hole diameter

l Thermal and electrical isolation


sleeve colours


ETA-15/0387

EJOT® facade anchor SDF-KB-8V


Diameter 8.0 mm

Drive Hexagon A/F10

Drill hole depth ≥ h1 60 mm

Embedment depth ≥ hnom 50 mm



[mm]

Price/100[EUR]



60 10 100 SDF-KB-8Vx60-V 8 570 060 430 4061245019048

80 30 100 SDF-KB-8Vx80-V 8 570 080 430 4061245019024

100 50 50 SDF-KB-8Vx100-V 8 570 100 430 4061245019000

120 70 50 SDF-KB-8Vx120-V 8 570 120 430 4061245018997

140 90 50 SDF-KB-8Vx140-V 8 570 140 430 4061245018980

160 110 50 SDF-KB-8Vx160-V 8 570 160 430 4061245018973

180 130 50 SDF-KB-8Vx180-V 8 570 180 430 4061245018966

200 150 50 SDF-KB-8Vx200-V* 8 570 200 430 4061245018959

220 170 50 SDF-KB-8Vx220-V* 8 570 220 430 4061245018942

* Delivery time upon request


Tensile strength NRk,p in concrete < C16/20 4.50 kN

Tensile strength NRk,p in concrete ≥ C16/20 6.50 kN


Solid lime sand brick KS, NF 20-2.0 2.00 kN

Transverse strength VRk,s





ETA-15/0387

SCANTO

SHOP

AF10

www.ejot.com24


Application range l Installation of timber or metal attach-

ments

l For non-supporting redundant systems ac-

cording to ETAG 020

l Suitable for the structural fastening of gates,

doors, windows, square timber


l Anchor with an embedment depth

of 40 mm in concrete

l Two installation depths (embedment in ma-

sonry 50 mm)

l Very short expansion part for extremely fast

installation

l Optimal expanding part due to radial expan-

sion

l Very high bending moment


sleeve colours

l Double safety lock against torsion for secure

installation

NotePlease observe European Technical Approval

ETA-10/0305 in the planning and processing of

products. Further information about parameters

and loads can be found in the approval.

EJOT® facade anchor SDF-S-10V

Anchorlength L

[mm]

Fasteningthickness t

fix (concrete / masonry)

≤ [mm]

Price/100[EUR]



50 10 / - 100 SDF-S-10Vx50-V 8 580 050 450 4061245018935

60 20 / 10 100 SDF-S-10Vx60-V 8 580 060 450 4061245018928

70 30 / 20 100 SDF-S-10Vx70-V 8 580 070 450 4061245018911

80 40 / 30 100 SDF-S-10Vx80-V 8 580 080 450 4061245018904

100 60 / 50 50 SDF-S-10Vx100-V 8 580 100 450 4061245018898

120 80 / 70 50 SDF-S-10Vx120-V 8 580 120 450 4061245018881

140 100 / 90 50 SDF-S-10Vx140-V 8 580 140 450 4061245018874

160 120 / 110 50 SDF-S-10Vx160-V 8 580 160 450 4061245018867

180 140 / 130 50 SDF-S-10Vx180-V 8 580 180 450 4061245018850

200 160 / 150 50 SDF-S-10Vx200-V 8 580 200 450 4061245018843

220 180 / 170 50 SDF-S-10Vx220-V 8 580 220 450 4061245018836

hh1nomh ttol

t fix

h

h1,1hnom,1

t fixtolt

h

h1,2hnom,2

t fixtolt

Concrete

hh1nomh ttol

t fix

h

h1,1hnom,1

t fixtolt

h

h1,2hnom,2

t fixtolt

Masonry


Diameter 10 mm

Hole depth in concrete h1.1 ≥ 50 mm

Effective Embedment depth in concrete hnom,1 ≥ 40 mm

Hole depth in masonry h1.2 ≥ 60 mm

Effective Embedment depth in masonry hnom,2 ≥ 50 mm

Drill hole diameter d0 10 mm

Through hole diameter of component to be attached df

≤ 10.5 mm

Drive TX40

Characteristic loads

Tensile load NRk,p in concrete C12/15

Temperature range 30 °C / 50 °C 4.50 kN


FRk brick Mz 20-1.8, NF 2.50 kN

FRk solid sand-lime brick KS 36, NF 4.00 kN

FRk solid sand-lime brick KS 20, 8 DF 4.50 kN

Transverse load VRk,s in concrete C12/15 at hnom,1 = 40 mm


Transverse load VRk,s at hnom,2 = 50 mm


Bending moment MRk,s at hnom,1 =40 mm


Side load MRk,s at hnom,2 = 50 mm


ETA-10/0305

TX40SCAN

TOSHOP

www.ejot.com 25


Application range l Installation of metal attachments


cording to ETAG 020

l Suitable for the structural fastening of wall

cupboards, cladding, metal angle pieces


l Anchor with an embedment depth of 40 mm

in concrete

l Two installation depths (embedment in ma-

sonry 50 mm)

l Very short expansion part for extremely fast

installation

l Optimal expanding part due to radial expan-

sion

l Very high bending moment


sleeve colours


installation





EJOT® facade anchor SDF-KB-10V


Diameter 10 mm


Effective Embedment depth in concrete hnom,1 ≥ 40 mm

Hole depth in masonry h1.2 ≥ 60 mm

Effective Embedment depth in masonry hnom,2 ≥ 50 mm



≤ 10.5 mm

Drive AF13/TX40





FRk brick Mz 20-1.8, NF 2.50 kN

FRk solid sand-lime brick KS 36, NF 4.00 kN

FRk solid sand-lime brick KS 20, 8 DF 4.50 kN

Transverse load VRk,s in concrete C12/15 at hnom,1 = 40 mm


Anchor with A4 stainless steel screw 9.12 kN

Transverse load VRk,s at hnom,2 = 50 mm



Bending moment MRk,s at hnom,1 =40 mm



Side load MRk,s at hnom,2 = 50 mm


Anchor with A4 stainless steel screw 26.62 Nm

Anchorlength L

[mm]

Fasteningthickness t

fix (concrete / masonry)

≤ [mm]

Price/100[EUR]



50 10 / - 100 SDF-KB-10Vx50-V 8 581 050 450 4061245018829

60 20 / 10 100 SDF-KB-10Vx60-V 8 581 060 450 4061245018805

70 30 / 20 100 SDF-KB-10Vx70-V 8 581 070 450 4061245018775

80 40 / 30 100 SDF-KB-10Vx80-V 8 581 080 450 4061245018751

100 60 / 50 50 SDF-KB-10Vx100-V 8 581 100 450 4061245018744

120 80 / 70 50 SDF-KB-10Vx120-V 8 581 120 450 4061245018737

140 100 / 90 50 SDF-KB-10Vx140-V 8 581 140 450 4061245018720

160 120 / 110 50 SDF-KB-10Vx160-V 8 581 160 450 4061245018713

180 140 / 130 50 SDF-KB-10Vx180-V 8 581 180 450 4061245018706

200 160 / 150 50 SDF-KB-10Vx200-V 8 581 200 450 4061245018690

220 180 / 170 50 SDF-KB-10Vx220-V 8 581 220 450 4061245018683

Anchor with A4 stainless steel screw (-E)

50 10 / - 100 SDF-KB-10Vx50-E 8 581 050 650 4061245018812

60 20 / 10 100 SDF-KB-10Vx60-E 8 581 060 650 4061245018799

70 30 / 20 100 SDF-KB-10Vx70-E 8 581 070 650 4061245018768

hh1nomh ttol

t fix

h

h1,1hnom,1

t fixtolt

h

h1,2hnom,2

t fixtolt

Concrete

hh1nomh ttol

t fix

h

h1,1hnom,1

t fixtolt

h

h1,2hnom,2

t fixtolt

Masonry

ETA-10/0305

SCANTO

SHOP

AF13/TX40

www.ejot.com26


Application range l Installation of timber or metal attachments


cording to ETAG 020



l For embedment in rain screens


l Approved for all common building materials

l Reliable hold in problematic building materi-

als thanks to optimised expansion part

l Radial expansion for reliable hold


sleeve colours


installation

NotePlease observe European Technical Approval ETA-10/0305 in the plan-ning and processing of products. Further information about param-eters and loads can be found in the approval.

EJOT® Universal anchor SDF-S-10H






Solid sand-lime brick KS 36, NF 4.50 kN

Solid sand-lime brick KS 20, 8 DF 4.50 kN

Solid lightweight concrete brick V6, 2 DF 2.00 kN

Vertically perforated brick HLz 12-0.9, NF 2.00 kN

Perforated sand-lime brick KSL 12, 4 DF 2.50 kN

Cavity block made of lightweight concrete Hbl 10, 12 DF

1.20 kN

Transverse load VRk,s





Compressive strength of aerated concrete [N/mm2] 30 - 50 °C

Aerated concrete 4 1.5 kN




Partial safety factor γMAAC 2.0


Diameter 10 mm


Effective embedment depth hnom ≥ 70 mm



≤ 10.5 mm

Drive TX40



[mm]

Price/100[EUR]



80 10 100 SDF-S-10Hx80-V 8 510 080 420 4061245019864

100 30 50 SDF-S-10Hx100-V 8 510 100 420 4061245019840

120 50 50 SDF-S-10Hx120-V 8 510 120 420 4061245019826

140 70 50 SDF-S-10Hx140-V 8 510 140 420 4061245019802

160 90 50 SDF-S-10Hx160-V 8 510 160 420 4061245019789

180 110 50 SDF-S-10Hx180-V 8 510 180 420 4061245019765

200 130 50 SDF-S-10Hx200-V 8 510 200 420 4061245019741

220 150 50 SDF-S-10Hx220-V 8 510 220 420 4061245019727

240 170 50 SDF-S-10Hx240-V 8 510 240 420 4061245019703

260 190 50 SDF-S-10Hx260-V 8 510 260 420 4061245019680

280 210 50 SDF-S-10Hx280-V 8 510 280 420 4061245019666

300 230 50 SDF-S-10Hx300-V 8 510 300 420 4061245019659

hh1nomh ttol

t fix

h

h1,1hnom,1

t fixtolt

h

h1,2hnom,2

t fixtolt

Installationsubstrate

ETA-10/0305

SCANTO

SHOP

TX40

www.ejot.com 27




cording to ETAG 020










sleeve colours


installation

NotePlease observe European Technical Approval ETA-10/0305 in the plan-ning and processing of products. Further information about param-eters and loads can be found in the approval.

EJOT® Universal anchor SDF-S-10H












1.20 kN













Diameter 10 mm





≤ 10.5 mm

Drive TX40



[mm]

Price/100[EUR]



80 10 100 SDF-S-10Hx80-E 8 510 080 620 4061245019857

100 30 50 SDF-S-10Hx100-E 8 510 100 620 4061245019833

120 50 50 SDF-S-10Hx120-E 8 510 120 620 4061245019819

140 70 50 SDF-S-10Hx140-E 8 510 140 620 4061245019796

160 90 50 SDF-S-10Hx160-E 8 510 160 620 4061245019772

180 110 50 SDF-S-10Hx180-E 8 510 180 620 4061245019758

200 130 50 SDF-S-10Hx200-E 8 510 200 620 4061245019734

220 150 50 SDF-S-10Hx220-E 8 510 220 620 4061245019710

240 170 50 SDF-S-10Hx240-E 8 510 240 620 4061245019697

260 190 50 SDF-S-10Hx260-E 8 510 260 620 4061245019673

280 210 50 SDF-S-10Hx280-E 8 510 280 620 4061245031514

300 230 50 SDF-S-10Hx300-E 8 510 300 620 4061245031521

hh1nomh ttol

t fix

h

h1,1hnom,1

t fixtolt

h

h1,2hnom,2

t fixtolt


ETA-10/0305

NEW

NEW

NEW

NEW

SCANTO

SHOP

TX40

www.ejot.com28




cording to ETAG 020










sleeve colours


installation





EJOT® Universal anchor SDF-KB-10H


Diameter 10 mm





≤ 10.5 mm

Drive AF13/TX40












1.20 kN















[mm]

Price/100[EUR]



80 10 100 SDF-KB-10Hx80-V 8 513 080 420 4061245019642

100 30 50 SDF-KB-10Hx100-V 8 513 100 420 4061245019611

120 50 50 SDF-KB-10Hx120-V 8 513 120 420 4061245019581

140 70 50 SDF-KB-10Hx140-V 8 513 140 420 4061245019567

160 90 50 SDF-KB-10Hx160-V 8 513 160 420 4061245019543

180 110 50 SDF-KB-10Hx180-V 8 513 180 420 4061245019529

200 130 50 SDF-KB-10Hx200-V 8 513 200 420 4061245019505

220 150 50 SDF-KB-10Hx220-V 8 513 220 420 4061245019482

hh1nomh ttol

t fix

h

h1,1hnom,1

t fixtolt

h

h1,2hnom,2

t fixtolt


ETA-10/0305

SCANTO

SHOP

AF13/TX40

www.ejot.com 29




cording to ETAG 020










sleeve colours


installation





EJOT® Universal anchor SDF-KB-10H


Diameter 10 mm





≤ 10.5 mm

Drive AF13/TX40












1.20 kN















[mm]

Price/100[EUR]



80 10 100 SDF-KB-10Hx80-E 8 513 080 620 4061245019635

100 30 50 SDF-KB-10Hx100-E 8 513 100 620 4061245019604

120 50 50 SDF-KB-10Hx120-E 8 513 120 620 4061245019574

140 70 50 SDF-KB-10Hx140-E 8 513 140 620 4061245019550

160 90 50 SDF-KB-10Hx160-E 8 513 160 620 4061245019536

180 110 50 SDF-KB-10Hx180-E 8 513 180 620 4061245019512

200 130 50 SDF-KB-10Hx200-E 8 513 200 620 4061245019499

220 150 50 SDF-KB-10Hx220-E 8 513 220 620 4061245019475

hh1nomh ttol

t fix

h

h1,1hnom,1

t fixtolt

h

h1,2hnom,2

t fixtolt


ETA-10/0305

SCANTO

SHOP

AF13/TX40

www.ejot.com30




cording to ETAG 020









sleeve colours


installation

NoteFor planning, please observe approval ETA-

15/0027.

EJOT® facade anchor SDF-S-14A



[mm]

Price/100[EUR]



120 50 50 SDF-S-14Ax120-V 8 591 120 430 4061245018638

140 70 50 SDF-S-14Ax140-V 8 591 140 430 4061245018621

160 90 50 SDF-S-14Ax160-V 8 591 160 430 4061245018614

180 110 50 SDF-S-14Ax180-V 8 591 180 430 4061245018607

200 130 50 SDF-S-14Ax200-V 8 591 200 430 4061245018591

220 150 50 SDF-S-14Ax220-V 8 591 220 430 4061245018584

240 170 25 SDF-S-14Ax240-V 8 591 240 430 4061245018577

260 190 25 SDF-S-14Ax260-V 8 591 260 430 4061245018560

280 210 25 SDF-S-14Ax280-V 8 591 280 430 4061245018553

300 230 25 SDF-S-14Ax300-V 8 591 300 430 4061245018546

320 250 25 SDF-S-14Ax320-V 8 591 320 430 4061245018539

340 270 25 SDF-S-14Ax340-V 8 591 340 430 4061245018522

360 290 25 SDF-S-14Ax360-V 8 591 360 430 4061245018515


Diameter 14 mm


Drill hole depth ≥ t 80 mm

Embedment depth ≥ hv 70 mm


Tensile load NRk,p in concrete > C12/15 8.50 kN


Solid lime sand brick KS, 2 DF 20-2.0 6.00 kN


Solid brick V, 3 DF 3.00 kN

Vertically perforated brick HLz, 2 DF 28-1.2 2.00 kN

Perforated sand-lime brick KSL, 8 DF 16-1.4 2.50 kN

Cavity block tile made of lightweight concrete Hbl, 12 DF

2.00 kN

Aerated concrete fb ≥ 2 N/mm2 1.20 kN










ht fixh1

nomh tolt

ht fixh1

nomh tolt

Ø14A

SDF-KB

Ø14A

SDF-S

ETA-15/0027

TX40SCAN

TOSHOP

www.ejot.com 31




cording to ETAG 020









sleeve colours


installation

NoteFor planning, please observe approval ETA-

15/0027.

EJOT® facade anchor SDF-KB-14A


Diameter 14 mm

Drive Hexagon A/F17





[mm]

Price/100[EUR]



80 10 50 SDF-KB-14Ax80-V 8 590 080 430 4061245018676

100 30 50 SDF-KB-14Ax100-V 8 590 100 430 4061245018652


Tensile load NRk,p in concrete > C12/15 8.50 kN




Solid brick V, 3 DF 3.00 kN

Vertically perforated brick HLz, 2 DF 28-1.2 2.00 kN

Perforated sand-lime brick KSL, 8 DF 16-1.4 2.50 kN

Cavity block tile made of lightweight concrete Hbl, 12 DF

2.00 kN











ht fixh1

nomh tolt

ht fixh1

nomh tolt

Ø14A

SDF-KB

Ø14A

SDF-S

ETA-15/0027

SCANTO

SHOP

AF17

www.ejot.com32


EJOT® facade anchor SDP-S-10G


Diameter 10 mm





Compressive strength of aerated concrete [N/mm2]






Characteristic Bending moment

Steel screw 17.7 Nm / γMs 1.50

Stainless steel screw 20.6 Nm / γMs 1.87



[mm]

Price/100[EUR]



80 10 100 SDP-S-10Gx80-V 8 530 080 420 4061245019468

100 30 50 SDP-S-10Gx100-V 8 530 100 420 4061245019444

120 50 50 SDP-S-10Gx120-V 8 530 120 420 4061245019420

140 70 50 SDP-S-10Gx140-V 8 530 140 420 4061245019406

160 90 50 SDP-S-10Gx160-V 8 530 160 420 4061245019383

180 110 50 SDP-S-10Gx180-V 8 530 180 420 4061245019369

200 130 50 SDP-S-10Gx200-V 8 530 200 420 4061245019345

220 150 50 SDP-S-10Gx220-V 8 530 220 420 4061245019321


80 10 100 SDP-S-10Gx80-E 8 530 080 620 4061245019451

100 30 50 SDP-S-10Gx100-E 8 530 100 620 4061245019437

120 50 50 SDP-S-10Gx120-E 8 530 120 620 4061245019413

140 70 50 SDP-S-10Gx140-E 8 530 140 620 4061245019390

160 90 50 SDP-S-10Gx160-E 8 530 160 620 4061245019376

180 110 50 SDP-S-10Gx180-E 8 530 180 620 4061245019352

200 130 50 SDP-S-10Gx200-E 8 530 200 620 4061245019338

220 150 50 SDP-S-10Gx220-E 8 530 220 620 4061245019314

Application range l Fixing wood components in aerated con-

crete


l Facade anchor with two-stage screw

l Reliable form-fit in the substrate thanks to

combined expansion zones

l High load capacity

l Available with steel screws or stainless steel

screws


sleeve colours


approval ETA-12/0502.

ETA-12/0502

TX40SCAN

TOSHOP

www.ejot.com 33



Diameter 10 mm

Drive A/F13/hexalobular TX40




Compressive strength of aerated concrete [N/mm2]






Characteristic Bending moment

Steel screw 17.7 Nm / γMs 1.50

Stainless steel screw 20.6 Nm / γMs 1.87

Application range l For embedment of metal components in

aerated concrete


l Facade anchor with two-stage screw

l Reliable form-fit in the substrate thanks to

combined expansion zones

l High load capacity

l Available with steel screws or stainless steel

screws


sleeve colours


approval ETA-12/0502.

EJOT® facade anchor SDP-KB-10G



[mm]

Price/100[EUR]



80 10 100 SDP-KB-10Gx80-V 8 532 080 420 4061245019307

100 30 50 SDP-KB-10Gx100-V 8 532 100 420 4061245019277

120 50 50 SDP-KB-10Gx120-V 8 532 120 420 4061245019246

140 70 50 SDP-KB-10Gx140-V 8 532 140 420 4061245019222

160 90 50 SDP-KB-10Gx160-V 8 532 160 420 4061245019208

180 110 50 SDP-KB-10Gx180-V 8 532 180 420 4061245019185

200 130 50 SDP-KB-10Gx200-V 8 532 200 420 4061245019161

220 150 50 SDP-KB-10Gx220-V 8 532 220 420 4061245019147


80 10 100 SDP-KB-10Gx80-E 8 532 080 620 4061245019291

100 30 50 SDP-KB-10Gx100-E 8 532 100 620 4061245019260

120 50 50 SDP-KB-10Gx120-E 8 532 120 620 4061245019239

140 70 50 SDP-KB-10Gx140-E 8 532 140 620 4061245019215

160 90 50 SDP-KB-10Gx160-E 8 532 160 620 4061245019192

180 110 50 SDP-KB-10Gx180-E 8 532 180 620 4061245019178

200 130 50 SDP-KB-10Gx200-E 8 532 200 620 4061245019154

220 150 50 SDP-KB-10Gx220-E 8 532 220 620 4061245019130

ETA-12/0502

SCANTO

SHOP

AF13/TX40

www.ejot.com34


Application range l For fast and adhesive-free subsequent

installation of curtain walls

l For load-bearing shells made of concrete,

solid brick and perforated brick

Characteristics l Approved anchor for fixing curtain walls

l Double expansion wall anchor: simultane-

ous embedment in load-bearing wall and

outer sheet

l Clean and fast installation (no mortar

required)

l Universal expansion zone: secure installa-

tion into concrete load-bearing shells, solid

and perforated brick

l The use of A4 stainless steel screws

guarantees corrosion protection

l 100% installation control

l Temperature-independent installation

l Can be installed at 0°C

EJOT® cavity wall repair anchor VSD

NoteThe EJOT® VSD double expansion wall anchor

enables the subsequent renovation of double-

leaf masonry.

Advanced corrosion or a complete lack of wire

anchors can lead to decreased stability of the

outer sheet and possibly cause considerable

physical injury.

In particular curtain walls made before 1979

should be subject to further inspection.

When renovating the outer facade, the stability

of the curtain wall must be verified. The EJOT®

VSD is a particularly cost-effective solution for

subsequent installation between load-bearing

shell and outer sheet.


Diameter 8 mm

Embedment depth hef ≥ 70 mm

Drill hole depth ts ≥ Id + 10 mm

Nominal drill diameter 8 mm

Minimum thickness of the outer sheet

115 mm


ef

VSD

s

z

d

a

Length ld mmDistance az

[mm]Price/100

[EUR]Order description Article number EAN


205 0 - 20 100 VSD-8Ux205-E 8 765 205 600 4061245010670

225 20 - 40 100 VSD-8Ux225-E 8 765 225 600 4061245010663

245 40 - 60 100 VSD-8Ux245-E 8 765 245 600 4061245010656

265 60 - 80 100 VSD-8Ux265-E 8 765 265 600 4061245010649

285 80 - 100 100 VSD-8Ux285-E 8 765 285 600 4061245010632

305 100 - 120 100 VSD-8Ux305-E 8 765 305 600 4061245010625

Z-21.2-1652

TX25SCAN

TOSHOP

www.ejot.com 35

Rear ventilated facadesAll wall plug

L [mm]

d0

[mm]D

[mm]tsheet, min

[mm]Price/100

[EUR]Order description Article number EAN

32 6 8.5 8 100 Gripper 6 all wall plug 9 650 075 232 4061245003146

38 8 12 12 50 Gripper 8 all wall plug 9 650 075 234 4061245003139

45 10 14 12 50 Gripper 10 all wall plug 9 650 075 236 4061245003122

GRIPPER all wall plug

Application range l For pre-installation in boards,

cavity and solid walls as well as in any other

construction material

Application examples l Hand rails

l Wall attachment of cabinets

l Ceiling lights

l Storage racks

l Bookcases

l Mounting televisions

l Heating bodies

l Wash basins

l Urinals

l Electrical installations

l Attachment of HVAC and sanitary equipment

l Attachment of sanitary equipment

Base materialsSuitable for

l Cinder blocks

l Plasterboard

l High-strength plasterboard

l Hollow expanded clay bricks

l Pre-stressed hollow core slab

l Natural stone

l Non-cracked concrete

l Vertically perforated clay bricks

l Hollow brick sandstone

l Bricks

l Expanded clay aggregate concrete solid

brick

l Solid brick sandstone

Characteristics

l Anchor made of thermoplastic elastomer -

The material adapts to the surface of the drill

hole, while the non-slip GripEdge surface

and the screws ensure secure mechanical

embedment

l GRIPPER surpasses normal anchors in

its power of resistance against long-term

stress, wear, weather conditions, moisture

and storage

l Can be used with all popular types and

diameters of screws

l The special collar keeps the anchor at the

optimal installation depth and also remains

covered by the screw head

Appropriate screwsø

[mmLength [mm]

GRIPPER 5 3-4.5 24 + tfix

GRIPPER 6 4- 5.5 32 + tfix

GRIPPER 8 4.5-6 38 + tfix

GRIPPER 10 4.5-7 45 + tfix

SCANTO

SHOP

www.ejot.com36

Rear ventilated facadesNail anchors

Nail anchor ND-K

Typed0

[mm]df

[mm]hnom

[mm]hef

[mm]AF

[mm]Tinst

[Nm]

Recommended loadsnon-cracked concrete C20/25

Recommended loadsBricks fb 20.5 N/mm2

NRec [kN] VRec [kN] NRec [kN] VRec [kN]

5x 30 5 5.5 25 25 PZ 2 - 0.2 0.2 0.1 0.1

5x 40 5 5.5 30 30 PZ 2 - 0.2 0.2 0.1 0.1

5x 50 5 5.5 30 30 PZ 2 - 0.2 0.2 0.1 0.1

6x 40 6 6.5 30 30 PZ 2 - 0.4 0.4 0.2 0.2

6x 60 6 6.5 30 30 PZ 2 - 0.4 0.4 0.2 0.2

6x 80 6 6.5 30 30 PZ 2 - 0.4 0.4 0.2 0.2

8x 60 8 8.5 40 40 PZ 2 - 0.6 0.6 0.3 0.3

8x 80 8 8.5 40 40 PZ 2 - 0.6 0.6 0.3 0.3

8x 100 8 8.5 40 40 PZ 2 - 0.6 0.6 0.3 0.3

Characteristic data and loads

L [mm]

d0

[mm]htot

[mm]tfix

[mm]Price/100

[EUR]Order description

Article number EAN

Anchors with zinc-plated steel screw

30 5 40 0-5 200 ND-K 5x 30 V 9 650 075 678 4061245002880

40 5 50 10 200 ND-K 5x 40 V 9 650 075 680 4061245002866

50 5 60 20 200 ND-K 5x 50 V 9 650 075 681 4061245002859

40 6 50 10 200 ND-K 6x 40 V 9 650 075 679 4061245002873

60 6 70 30 200 ND-K 6x 60 V 9 650 075 682 4061245002842

80 6 90 50 100 ND-K 6x 80 V 9 650 075 683 4061245002835

60 8 70 20 100 ND-K 8x 60 V 9 650 075 684 4061245002828

80 8 90 40 100 ND-K 8x 80 V 9 650 075 685 4061245002811

100 8 110 60 100 ND-K 8x 100 V 9 650 075 686 4061245002804

Anchor with stainless steel screw

30 5 40 0-5 200 ND-K 5/30 E 9 650 075 691 4061245002798

40 6 50 10 200 ND-K 6/40 E 9 650 075 692 4061245002781

80 6 90 50 100 ND-K 6/80 E 9 650 075 693 4061245002774

80 8 90 40 100 ND-K 8/80 E 9 650 075 694 4061245002767

Application rangeTime-saving simple speed plug for light fasten-

ings:

l Substructures

l Cabinets

l Skirting boards

l Battens

l Cable racks

l Cable clips

l Pipe supports



l Bricks

l Natural stone

l Vertically perforated bricks

Characteristics l Pre-assembled with nail screw, ready-to-

assemble nylon plugs for drive-in

l Nail screw head with Pozidriv recess for the

removal or adjustment of the anchor

l The plug collars serve as plastic insulating

washers and thus prevent galvanic corro-

sion

l Suitable conditions concerning the material

quality of the nail screws:

GVZ for dry indoor areas

SCANTO

SHOP

PZ 2

www.ejot.com 37

Rear ventilated facadesNail anchors

EJOT® Nail anchor ND-S

L [mm]

d0

[mm]htot

[mm]tfix

[mm]Price/100

[EUR]Order description

Article number EAN

Anchors with zinc-plated steel nail

30 5 40 0-5 200 ND-S 5x 30 V 9 650 075 658 4061245002965

50 5 60 20 200 ND-S 5x 50 V 9 650 075 659 4061245002958

40 6 50 10 200 ND-S 6x 40 V 9 650 075 660 4061245002941

60 6 70 30 200 ND-S-6x 60 V 9 650 075 661 4061245002934

80 6 90 50 100 ND-S-6x 80 V 9 650 075 662 4061245002927

60 8 70 20 100 ND-S 8x 60 V 9 650 075 665 4061245002897

80 8 90 40 100 ND-S-8x 80 V 9 650 075 663 4061245002910

100 8 110 60 100 ND-S 8x 100 V 9 650 075 664 4061245002903

120 5 40 0-5 100 ND-S 8x 120 V 9 650 075 610 4061245003115

140 6 50 10 100 ND-S 8x 140 V 9 650 075 611 4061245003108

160 6 90 50 100 ND-S 8x 160 V 9 650 075 612 4061245003092

Typed0

[mm]df

[mm]hnom

[mm]hef

[mm]AF

[mm]Tinst

[Nm]

Recommended loadsnon-cracked concrete C20/25

Recommended loadsBricks fb 20.5 N/mm2

NRec [kN] VRec [kN] NRec [kN] VRec [kN]

5x 30 5 5.5 25 25 PZ 2 - 0.2 0.2 0.1 0.1

5x 50 5 5.5 30 30 PZ 2 - 0.2 0.2 0.1 0.1

6x 40 6 6.5 30 30 PZ 2 - 0.4 0.4 0.2 0.2

6x 60 6 6.5 30 30 PZ 2 - 0.4 0.4 0.2 0.2

6x 80 6 6.5 30 30 PZ 2 - 0.4 0.4 0.2 0.2

8x 60 8 8.5 40 40 PZ 2 - 0.6 0.6 0.3 0.3

8x 80 8 8.5 40 40 PZ 2 - 0.6 0.6 0.3 0.3

8x 100 8 8.5 40 40 PZ 2 - 0.6 0.6 0.3 0.3

8x 120 8 8.5 40 40 PZ 2 - 0.6 0.6 0.3 0.3

8x 140 8 8.5 40 40 PZ 2 - 0.6 0.6 0.3 0.3

8x 160 8 8.5 40 40 PZ 2 - 0.6 0.6 0.3 0.3

Characteristic data and loads

Application rangeTime-saving simple speed plug for

light fastenings

l Substructures

l Cabinets

l Skirting boards

l Battens

l Cable racks

l Cable clips

l Pipe supports



l Bricks

l Natural stone

l Vertically perforated bricks

Characteristics l Countersunk head anchors with zinc-plated

steel nail

l Pre-assembled with nail screw, ready-to-

assemble nylon plugs for drive-in

l Nail screw head with Pozidriv recess for the

removal or adjustment of the anchor

l The plug collars serve as plastic insulating

washers and thus prevent galvanic corro-

sion

l Suitable conditions concerning the material

quality of the nail screws:

GVZ for dry indoor areas

SCANTO

SHOP

PZ 2

www.ejot.com38

Rear ventilated facadesAssembly elements for External Thermal Insulation Composite Systems (ETICS)

Order descriptionPrice/1[EUR]

Article number EAN

EJOT Iso-Dart 80 10 8 500 080 440 4039161012771

EJOT Iso-Dart 100 10 8 500 100 440 4039161012788

EJOT Iso-Dart 120 10 8 500 120 440 4039161012795

EJOT Iso-Dart 140 10 8 500 140 440 4039161012801

EJOT Iso-Dart 160 10 8 500 160 440 4039161012818

EJOT Iso-Dart 180 10 8 500 180 440 4039161012825

EJOT Iso-Dart 200 10 8 500 200 440 4039161012832

EJOT Iso-Dart 220 10 8 500 220 440 4039161012849

EJOT Iso-Dart 240 10 8 500 240 440 4039161012856

EJOT Iso-Dart 260 10 8 500 260 440 4039161012863

EJOT Iso-Dart 280 10 8 500 280 440 4039161013273

EJOT® Iso-Dart

Included in delivery10 EJOT facade anchors (1)10 installation bushes (2) 10 seals (3) 10 reduction inserts (4)1 installation bit (5)

Application range For retrofitting of light to medium heavy attach-

ments to ETICS facades made of EPS, mineral

wool and mineral foam, like for example:

l Downpipe brackets

l Folding shutter latch

l Signs and billboards

l Lamps

Characteristics l Installation bush made of glass-fibre-rein-

forced plastic including a high-quality EPDM

sealing washer and an EJOT facade anchor

(Ø 8 mm)

l Attachments are fastened with common

hanger bolts or coarse thread screws

l Common assembly tool

l Recommended service load for each fixing

point max. 15 kg

Benefits l High load-bearing capacity through load

extension into the substrate

l Reduced thermal transmission by thermal

decoupling – Chi value 0.002 W/K according

to TR 025

l Waterproofing against the plaster shell with

high-quality EPDM seal - Inspection of the

resistance to driving rain in accordance with

DIN EN 12155

l Easy and quick installation


Drill hole diameter 8.0 mm

Drill hole depth h1 ≥ in the substrate 80 mm


Processing in installation bush

Coarse thread screws Ø 9 mm

Hanger bolts Ø 9 mm, M10

Minimum installation depth 40 mm

Processing in installation bush + reduction insert

Coarse thread screws Ø 5 mm / Ø 6 mm

Minimum installation depth 35 mm

2

4

5

2

1 3

4

41 mm

77 m

m

TX30SCAN

TOSHOP

NEW

www.ejot.com 39

Rear ventilated facadesAssembly elements for External Thermal Insulation Composite Systems (ETICS)

EJOT® Iso-Dart

Recommended service loads

SubstrateRaw density class ?

[kg/dm3]

Minimum compressive strength fb

[N/mm2]

Axial tensile strength 1)

[kN]

Shear force-carrying capacity

[kN]

Concrete ≥ C12/15 - - 0.30 0.15

Solid clay brick ≥ 1.8 12 0.30 0.15

Solid sand-lime brick ≥ 1.8 12 0.30 0.15

Solid masonry of lightweight concrete

≥ 0.5 4 0.25 0.15

Vertically perforated clay bricks ≥ 0.9 12 0.25 0.15

Perforated sand-lime brick ≥ 1.6 12 0.25 0.15

Lightweight concrete hollow blocks ≥ 0.5 2 0.15 0.15

Aerated concrete ≥ 0.5 4 0.20 0.15

Chipboard and OSB boards, d ≥ 18 mm

- - 0.20 0.10

Solid construction timber, d ≥ 60mm

- - 0.30 0.15

Details apply for the shear force transmission immediately after the bush.1) When using the reduction insert the axial force is limited to max. 0.2 kN.

Application matrix

Insulation thickness

[mm]Concrete and masonry1) Solid wood2)

Timber composite plates2) (OSB, wood chipboard d≥18

mm)

80 EJOT Iso-Dart 80 - -

100 EJOT Iso-Dart 100 - -

120 EJOT Iso-Dart 120 EJOT Iso-Dart 100 EJOT Iso-Dart 80









300 - EJOT Iso-Dart 280 EJOT Iso-Dart 260

320 - - EJOT Iso-Dart 2801) Tolerance compensation up to 30 mm2) Using the screw without anchor sleeve - only pre-drill up to the substrate

www.ejot.com40

Rear ventilated facadesInsulation support anchors

Price/100[EUR]


Washer only

300 Washer DH 8 550 090 999 4061245011592

Insulation thickness ≤

[mm]

Price/100[EUR]


Shaft only

60 300 Shaft DH 60 8 550 060 999 4061245011622

80 300 Shaft DH 80 8 550 080 999 4061245011608

100 300 Shaft DH 100 8 550 100 999 4061245011578

120 300 Shaft DH 120 8 550 120 999 4061245011554

140 300 Shaft DH 140 8 550 140 999 4061245011530

160 300 Shaft DH 160 8 550 160 999 4061245011516

180 300 Shaft DH 180 8 550 180 999 4061245011493

200 300 Shaft DH 200 8 550 200 999 4061245011479

220 300 Shaft DH 220 8 550 220 999 4061245011455

240 300 Shaft DH 240 8 550 240 999 4061245011431

260 300 Shaft DH 260 8 550 260 999 4061245011417

280 300 Shaft DH 280 8 550 280 999 4061245011394

300 300 Shaft DH 300 8 550 300 999 4061245011370

EJOT® insulation support anchor DH (individual components)

Application range l For fixing insulating material in the rear

ventilated facade (VHF) to all substrates

Benefits l Prevents "quilt effect"

(indentations in the insulation) due to retro-

fitting of the washer

l Prevents gaping of the joints between the

individual insulating panels at the joining

edges

l Packing and handling volume is reduced by

over 60% compared to one-part insulation

support anchors

l Installation depth limiter guarantees

defined installation, independent of the

substrate

l Process reliable installation even with thick

insulation boards

Characteristics l Requirement: 5 pcs. per m2

l Easy installation with no additional expan-

sion element

l Parts can be positioned freely on the shaft

l All-purpose for all building materials

NoteFor the installation of two-ply insulation,

additional stress plates are required. The prac-

ticability depends on the respective insulation

properties and needs to be tested on site.

Rotary hole drilling is obligatory in aerated

concrete and perforated brick masonry.


Plate diameter 90 mm

Shaft diameter 8 mm

Drill bit diameter 8 mm



Point thermal transmittance χ 0.0001 W/K

Carrying capacity (pull over washer) 0.2 kN

Wall embedmentSingle-ply insulation

SCANTO

SHOP

www.ejot.com 41


Insulation thickness ≤

[mm]

Price/100[EUR]


Set, comprised of washer and shaft

40 300 DH-40 (one-part) 8 551 906 009 4061245011363

60 300 Set DH-60 8 550 060 009 4061245011639

80 300 Set DH-80 8 550 080 009 4061245011615

100 300 Set DH-100 8 550 100 009 4061245011585

120 300 Set DH-120 8 550 120 009 4061245011561

140 300 Set DH-140 8 550 140 009 4061245011547

160 300 Set DH-160 8 550 160 009 4061245011523

180 300 Set DH-180 8 550 180 009 4061245011509

200 300 Set DH-200 8 550 200 009 4061245011486

220 300 Set DH-220 8 550 220 009 4061245011462

240 300 Set DH-240 8 550 240 009 4061245011448

260 300 Set DH-260 8 550 260 009 4061245011424

280 300 Set DH-280 8 550 280 009 4061245011400

300 300 Set DH-300 8 550 300 009 4061245011387

EJOT® insulation support anchor DH (set)

NoteFor the installation of two-ply insulation,

additional stress plates are required. The prac-

ticability depends on the respective insulation

properties and needs to be tested on site.



Wall embedmentSingle-ply insulation

Values determined by the



Shaft diameter 8 mm




Point thermal transmittance χ 0.0001 W/K

Carrying capacity (pull over washer) 0.2 kN

Application range l For fixing insulating material in the rear

ventilated facade (VHF) to all substrates

Benefits l Prevents "quilt effect"

(indentations in the insulation) due to retro-

fitting of the washer

l Prevents gaping of the joints between the

individual insulating panels at the joining

edges

l Installation depth limiter guarantees

defined installation, independent of the

substrate

l Process reliable installation even with thick

insulation boards

l Packing and handling volume is reduced by

over 60% compared to one-part insulation

support anchors

Characteristics l Requirement: 5 pcs. per m2

l Easy installation with no additional expan-

sion element

l Parts can be positioned freely on the shaft

l All-purpose for all building materials

SCANTO

SHOP

www.ejot.com42


EJOT® installation point

Application range l Installation tool for ceiling insulation, lintels

and split-mould insulation

l Attaches to the DH insulation support

anchor

Price/100[EUR]


10 Installation point for DH 8 550 000 031 4061245011646

Wall embedmentTwo-ply insulation with installation point

Ceiling embedmentSingle-ply insulation with installation point

SCANTO

SHOP

www.ejot.com 43




Shaft diameter 8 mm




Axial distance a ≥ 120 mm

Edge distance ar ≥ 60 mm

Minimum component thickness hmin 80 mm

Recommended tensile loads Frec

Concrete ≥ B25 0.20 kN

Solid sand-lime brick 0.20 kN

Bricks 0.20 kN

Vertically perforated clay bricks 0.05 kN

Perforated sand-lime brick 0.05 kN

Recommended transverse loads Frec

Concrete ≥ B25 0.25 kN

Solid sand-lime brick 0.25 kN

Bricks 0.25 kN

Vertically perforated clay bricks 0.10 kN

Perforated sand-lime brick 0.15 kN

Application range l For fixing hard insulation materials

l In combination with the EJOT® DMT metal

insulation stress plate also for fixing soft insula-

tion materials

l For fixing insulation materials for high fire

protection requirements.

Characteristics l Easy installation by striking in, self-

expanding

l Easy installation

l Fire performance class A1: non-combustible

according to DIN EN 13501-1:2010-01 (test

certificate no. PZ 3.1/17-226-1)

NoteThe EJOT® insulation support anchors are used

to fasten soft and hard insulating material in

rear ventilated facades. The insulation board

fastening is carried-out according to DIN

18516-1.



For the usage in non-accessible areas of rear-

ventilated facades, we recommend the metal

insulation support anchor made of stainless

steel.

EJOT® metal insulation support anchor DMH


Insulation thickness B ≤

[mm]

Price/100[EUR]


Alu-zinc steel

80 40 250 DMH-8x80-V 9 700 030 301 4061245010373

110 70 250 DMH-8x110-V 9 700 030 602 4061245010359

140 100 250 DMH-8x140-V 9 700 030 603 4061245010342

170 130 250 DMH-8x170-V 9 700 030 912 4061245010335

200 160 250 DMH-8x200-V 9 700 031 215 4061245010328

250 210 200 DMH-8x250-V 9 700 031 520 4061245010304

300 260 200 DMH-8x300-V 9 700 031 300 4061245010311

A2 stainless steel

80 40 250 DMH-8x80-E 9 700 030 302 4061245010366

110 70 250 DMH-8x110-E 9 700 033 603 4061245010298

140 100 250 DMH-8x140-E 9 700 036 904 4061245010243

170 130 250 DMH-8x170-E 9 700 035 912 4061245010250

200 160 250 DMH-8x200-E 9 700 035 215 4061245010281

250 210 200 DMH-8x250-E 9 700 035 520 4061245010267

300 260 200 DMH-8x300-E 9 700 035 300 4061245010274

A1

SCANTO

SHOP

www.ejot.com44


EJOT® metal insulation stress plate DMT

Application range l For fastening soft insulating materials in

combination with the EJOT® DMH metal

insulation support anchor

l For fixing soft insulating materials for high

fire protection requirements

Characteristics l Fire performance class A1: non-combustible

according to DIN EN 13501-1:2010-01 (test

certificate no. PZ 3.1/17-226-1)

Ø [mm]

Price/100[EUR]


Alu-zinc steel

80 250 DMT-80-V 9 700 030 156 4061245010397

A2 stainless steel

80 250 DMT-80-E 9 700 030 157 4061245010380

A1

SCANTO

SHOP

www.ejot.com 45

Accessories

Application range l To compensate for tolerances on wall and

roof

Characteristics l Plastics

l All-purpose for anchor diameters

of 6/8/10 mm

l Easy installation through clipping-on from

the side

l Variable combinations

EJOT® AS spacer

Thick-ness [mm]

Price/100[EUR]


3 100 AS-3 8 600 725 700 4061245020501

5 100 AS-5 8 601 189 710 4061245020488

8 100 AS-8 8 601 233 720 4061245020464

10 100 AS-10 8 601 232 750 4061245020471

15 100 AS-15 8 601 187 730 4061245020495


Dimensions 50 x 50 mm

SCANTO

SHOP

Notes

46

www.ejot.com 47

ContactInternational

AUSTRIAEJOT Austria GmbH & Co KGGrazer Vorstadt 146 A-8570 Voitsberg Phone: +43 3142 2 76 00-0 Fax: +43 3142 2 76 00-30 E-mail: [email protected] Internet: www.ejot.at

BALTIC STATESUAB EJOT BalticTitnago g. 19 LT-02300 Vilnius Phone: +370 5 23 11-437 Fax: +370 5 23 11-439 E-mail: [email protected]: www.ejot.lt

BENELUXEJOT Benelux bvba/sprlReedonk 19-1B-2880 BornemPhone: +32 3 740 79 70Fax: +32 3 740 79 79E-mail: [email protected] Internet: www.ejot.be

BRAZILEJOT & Fey Ltda. Rod BR 470, 2451 - Rio MortoIndaial - SC, 89130-000, BrasilPhone: +55 47 3281-7000E-mail: [email protected]: www.ejot.com.br

BULGARIAEJOT Bulgaria EOOD & Ko KDGurmazovsko shose No 962227, Bozhurishte Phone: +359 2421 96 37Fax: +359 2421 96 37E-mail: [email protected]

BOSNIA AND HERZEGOVINAEJOT d.o.o. SarajevoRajlovacka b.b.BiH-71000 SarajevoPhone: +387 33 782 760E-mail: [email protected]

CANADAEJOT Construction Fastening Systems Inc.50 Fleming Drive, Unit 4Cambridge, ON N1T 2B1phone: +1 226 499 9977e-mail: [email protected]: www.ejot.com

CHINAEJOT Fastening System (Taicang) Co., LtdNo.165 Fada Road Loudong Street Taicang, Jiangsu ProvinceP.R. China 215413Phone: +86 512 53 56 52 90-105Fax: +86 512 53 56 62 92E-mail: [email protected]: www.ejot.cn

CROATIAEJOT Spojna Tehnika d.o.o.Franje Lučića 23/3HR-10090 ZagrebPhone: +385 1 349 86 12Fax: +385 1 349 89 63E-mail: [email protected]

CZECH REPUBLIC EJOT CZ, s.r.o.Zdĕbradská 65CZ-25101 Řičany-JažlovicePhone: +420 323 62 78 11Fax: +420 323 62 78 20E-mail: [email protected]: www.ejot.cz

DENMARKEJOT Danmark ApSIndustrisvinget 8 DK-4683 Rønnede Phone: +45 56 39 08 42Fax: +45 56 39 91 06E-mail: [email protected]: www.ejot.dk

FINLANDSormat OyHarjutie 5FI-21290 RuskoPhone: +358 (0)207 94 0200Fax: +358 (0)201 76 3888E-mail: [email protected] Internet www.sormat.com

FRANCEEJOT France S.à.r.l.Z.I. de Villé - 5 rue du Climont B.P. 40023 F-67220 Villé Phone: +33 388 58 92 00Fax: +33 388 58 92 01E-mail: [email protected]: www.ejot.fr

GERMANYEJOT Construction DivisionIn der Stockwiese 35D-57334 Bad Laasphe, GermanyPhone: +49 2752 908-0fax: +49 2752 908-731e-mail: [email protected]: www.ejot.de

HUNGARYEJOT Hungaria Kft.Leshegy út 16.H-2310 SzigetszentmiklósPhone: +36 30 546 6807E-mail: [email protected]: www.ejot.hu

INDIAEJOT Fastening Systems Pvt. Ltd.A-501/502, Millennium Plaza, Sector-27, Gurgaon -1240022, Haryana, lndiaphone: +91 124 4200 492fax: +91 124 4200 493e-mail: [email protected]

ITALYEJOT S.A.S. di EJOT Tecnologie di fissaggio S.R.L.Via Marco Polo 16I-35011 Campodarsego (PD)Phone: +39 049 98690 00E-mail: [email protected]: www.ejot.it

JAPAN EJOT Japan L.L.C. 1742-1 Yamada, Kawagoe-Shi, Saitama-Ken, 350-0822 JapanPhone: +81 49 227 9181Fax: +81 49 227 9112

MEXICOEJOT ATF Fasteners de México y Compañía, S. en C. División Fijaciones para la ConstrucciónAv. Del Siglo No. 180 Parque Industrial MillenniumSan Luis Potosí S.L.P.C.P. 78395 MéxicoPhone: +52 444 8 70 82 25E-mail: [email protected]: www.ejot-atf.com

NORWAYEJOT Festesystem A/SAslakveien 20AN-0701 OsloPhone: +47 23 25 30 40Fax: +47 23 25 30 41E-mail: [email protected]: www.ejot.no

POLANDEJOT Polska Spółka z ograniczoną odpowiedzialnością Spółka komandytoUl. Jeżowska 9 PL-42-793 Ciasna Phone: +48 34 351 06 60 Fax: +48 34 353 54 10 E-mail: [email protected] Internet: www.ejot.pl

ROMANIAEJOT Romania SRLStr. Depozitelor 27RO-110078 PitestiPhone: +40 248 223 886Fax: +40 248 223 887E-mail: [email protected]

RUSSIAOOO EJOT WOSTOK105523 Moscow, RussiaSchelkovskoe highway, 100 bld. 1Office 5111Phone: +7 495 259 09 09Fax: +7 495 259 09 09E-mail: [email protected]: www.ejot.ru

SERBIAEJOT Tehnika spajanja d.o.o. Autoput Beograd-Novi Sad 296X SCG-Serbia, 11080 ZemunPhone: +381 11 748 60 82Fax: +381 11 748 00 56E-mail: [email protected]

SLOVAKIAEJOT Slovakia, s.r.o.Juzná trieda 82 (Areál VSS)SK-04017 KošicePhone: +421 55 622 17 60Fax: +421 55 678 09 57E-mail: [email protected]: www.ejot.sk

SPAINEJOT Ibérica, S.L.U.C/ Chile, 4 edificio II - oficina 30E-28290 Las Matas (Las Rozas) MadridPhone: +34 916 300 822Fax: +34 911 383 815E-mail: [email protected] Internet: www.ejot.es

SWEDENEJOT Sverige ABSandtagsvägen 9S-70236 ÖrebroPhone: +46 19 20 65 00Fax: +46 19 20 65 28E-mail: [email protected]: www.ejot.se

SWITZERLANDEJOT Schweiz AGUttwiler Strasse 3CH-8582 DozwilPhone: +41 71 414 52 22Fax: +41 71 414 52 50 E-mail: [email protected]: www.ejot.ch

TAIWAN

EJOT Taiwan Branch4No. 8, Aly. 81, Ln. 296, Xinya Rd., Qianzhen Dist. 80673 Kaohsiung, Taiwan, R.O.C.Phone: +886 7 811 08 18e-mail: [email protected]

TURKEYEJOT TezmakCebeci Cad. No. 84TR-34250 Küçükköy-IstanbulPhone: +90 212 477 77 92-95Fax: +90 212 538 00 93E-mail: [email protected]: www.ejot-tezmak.com

UNITED ARAB EMIRATESEJOT Middle East FZESharjah Airport International Free ZoneP.O. Box 120588 SharjahUnited Arab Emirates Phone: +971 6 557 97-70Fax: +971 6 557 97-75 E-mail: [email protected] Internet: www.ejot.com

UNITED KINGDOMEJOT U.K. Ltd.Hurricane CloseSherburn Enterprise ParkSherburn- in- ElmetLeeds, LS25 6PB, GBPhone: +44 1977 68 70 40Fax: +44 1977 68 70 41E-mail: [email protected]: www.ejot.co.uk

USAEJOT Fastening Systems L.P.9900 58th Place, Suite 100Kenosha, Wisconsin 53144 USAPhone: +1 262 612 35 50Fax: +1 262 721 12 45E-mail: [email protected]: www.ejot-usa.com

www.globalfasteneralliance.com

EJOT Baubefestigungen GmbHIn der Stockwiese 35

D-57334 Bad Laasphe, Germany

Phone: +49 2752 908-0

Fax: +49 2752 908-731

E-Mail: [email protected]

Website: www.ejot.com

651-

EN

/-/0

7.19

Rear Ventilated Facades - EJOT

Documents

Transcript of Rear Ventilated Facades - EJOT