Front and rear view cameras General

Front and rear view cameras
General
More information can be found in the document entitled Connecting a camera with lens cover to the infotainment system.

GeneralThis document describes the options from the factory available for front and rear view cameras. Most of the options described are variants of the option Camera sys-tem FFU (variant family 3832). When variants of this option are mentioned in the document, only the name of the variant and the variant code are provided.

More information on front view cameras and rear view cameras with accessories can be found on the Scania Vehicle Accessories Online website (http://accessories.scan-ia.com).

Contact a Scania dealer for ordering.

Scania Truck Bodybuilder 22:10-710 Issue 6 2022-03-30© Scania CV AB 2022, Sweden 1 (18)

Front view camera


403 3

87

Front view camera accompanying front view mirror 022090.

433

980

Area View FFU, 360° digitally positioned in the centre of the sun visor.

Front view cameraThere are 3 front view camera systems. The 3 front view camera systems are fitted in the sun visor; see illustrations. Depending on the option, the picture from the front view camera is either displayed on the infotainment system monitor or on a separate 7" or 10" monitor.

Information about separate 7" and 10" monitors can be found under the heading Sep-arate monitors.

Camera system accompanying front view mirrorThe front view camera in the Front view camera (variant code 3832E) and Front view camera with 7" monitor (variant code 3832F) options is located in the sun visor on the passenger side and displays the area in front of the cab and outside the passen-ger side; see illustration. The camera has a shooting angle of 118°.

On vehicles fitted with the option Front view camera (variant code 3832E), the cam-era is connected to the infotainment system monitor. The camera is always active at vehicle speeds up to 30 km/h, but never above this speed.

On vehicles fitted with the Front view camera with 7" monitor (variant code 3832F) option, the camera is connected to a separate 7" monitor. The camera is always active at speeds up to 30 km/h. At speeds above 30 km/h, the camera is only active when the direction indicator is activated.

On vehicles fitted with the option Area ViewFFU, 360° digital (variant code 9026A), the camera is positioned in the centre of the sun visor; see illustration. The camera displays the area in front of the cab as a part of the 360° area view. The camera has a recording angle of 190°. Area View The system is always active at speeds up to 40 km/h.


Front view camera


414

233

Front view camera that replaces the front view mirror.

Camera system as replacement for front view mirrorThe front view camera in the option Front view camera with separate 10" monitor (variant code 3832G) displays the area in front of the cab. The camera is connected to a separate 10" monitor. The camera has a recording angle of 270° and is always active when the starter lock is in drive mode.

For vehicles registered in the EU and WVTA markets, it is prohibited to remove front view mirrors.


Rear view camera


394 4

51

Suggested final rear view camera position.

Rear view cameraNote:The infotainment system monitor does not have a function to mirror the camera view. When retrofitting a rear view camera that will show the picture on the infotainment system monitor, the camera must be of a type that mirrors the picture.

There are 2 different positions for the rear view camera: on the chassis frame end beam or on the rear cab wall. Depending on the option, the picture from the rear view camera is shown on the infotainment system monitor or on a separate 7" monitor. The camera has a shooting angle of 118°.

Rear view camera on the chassis frameThe rear view camera in the Rear view camera for trucks (variant code 3832H) and Rear view camera for trucks with separate 7" monitor (variant code 3832J) options is positioned at the rear end of the chassis frame.

The camera gives an overview of the area behind the truck. The rear view camera is delivered transport-mounted from the factory. The bodybuilder fits the camera in the correct position, e.g. on the chassis frame end beam; see illustration. The camera is activated when reverse gear is engaged.

Rear view camera on rear cab wallThe rear view camera in the Rear view camera connected to the infotainment system monitor (variant code 3832K) option is positioned on the rear cab wall. The camera gives an overview of the area behind the cab. The vehicle is fitted with a cable har-ness from the infotainment system to the rear wall of the cab. The camera is supplied loose in the cab. The bodybuilder installs and connects the camera. The camera is ac-tivated when reverse gear is engaged.


Rear view camera


50 mm 50 mm

2000 mm

351 1

22

Measurements for positioning the rear view camera.

Directions for positioning the rear view cameraIf the rear view camera is positioned so that its lower edge is less than 2 m from the ground at the highest permitted load weight, the following requirements apply:

• The camera must not protrude more than 50 mm outside the width of the vehicle; see illustration. This is stipulated in international vehicle regulation ECE R46.

• Sharp edges on the camera with a radius of less than 2.5 mm must not be able to come into contact with anything within a diameter of 100 mm

Extension cable for rear view cameraThe factory-fitted cable harness for the rear view camera is approx. 13 m long meas-ured from the gearbox beam. If the rear view camera needs to be positioned far away from its original position, an extension cable may be necessary. The vehicle can be factory-fitted with the Camera system, extension cable FFU, 5 metres (variant code 7551A) option.

More information about the option can be found under the heading Ordering options.


Rear view camera


414

238

Positioning the harness-to-component connector for connecting a rear view camera located on a trailer.

Connecting a rear view camera located on a trailerThe Preparation for rear view camera on semi-trailer (variant code 3832L) and Preparation for rear view camera on semi-trailer, separate 7" monitor (variant code 3832M) options allow a rear view camera to be connected to a trailer.

Depending on the option, the image is displayed on the infotainment system monitor or on a separate 7" monitor.

More information about the options can be found under the heading Ordering op-tions.

The rear view camera is activated when the reverse gear is engaged. The rear view camera on the truck is automatically disengaged when the rear view camera on the trailer is connected.

Connecting the Area View camera system1 rear view camera and 2 side view cameras are included in vehicles factory-fitted with the Area ViewFFU, 360° digital (variant code 9026A) option. The cameras are supplied in a plastic bag in the cab storage box. A document containing information on FFU customization for the bodybuilder is placed in the cab. The Area View sys-tem must be calibrated after installing a camera on the bodywork.

More information on calibration can be found on the Scania Vehicle Accessories website (https://accessories.scania.com).


Separate monitor


404 1

92

7" monitor.

414 2

46

10" monitor.

414 2

52

Combination of 7" and 10" monitor.

Separate monitorDepending on the option, images from the front view camera and rear view camera are displayed on a separate monitor. The separate monitors are available in 2 sizes: 7" and 10".

The 7" and 10" monitors are both positioned on the centre panel in the cab; see illus-trations. The 7" monitor can display images from both the front and rear view cam-eras. The 10" monitor only displays images from the front view camera.


Separate monitor


432

385

7" monitor for Area View, 360° digital.

Vehicles fitted with the Area ViewFFU, 360° digital (variant code 9026A) option display images from all 4 cameras on a 7" monitor; see illustration. The view adapts to vehicle speed, oscillation signals and gear position while driving. This enables di-rectional operation and the vehicle is safer to operate in a turn.

More information on Scania 360 Area View can be found on the Scania Vehicle Ac-cessories website (https://accessories.scania.com).More information on the options that show the picture on a separate monitor can be found under the heading Ordering options.


Scania's infotainment system


394 4

54

Scania infotainment system with monitor.

Scania's infotainment systemFor the image from the camera to be displayed on the infotainment system monitor, the vehicle must be fitted with the Infotainment system 2 DIN with 7" monitor (pre-mium) (variant code 5120B) option. The infotainment system with monitor is posi-tioned in the instrument panel; see illustration.


Ordering options


Description

Rear view camera with lens cover that is connected to the infotainment system monitor and is activated when reverse gear is engaged. The lens cover is lowered and protects the camera lens from dirt and dust when the vehicle is driving forwards. The camera is temporarily fit-ted at the rear end of the frame and final refitting must be handled by the bodybuilder or customer.

Preparation for rear view camera for mounting on the rear wall of the cab. Can be used to see loading and unloading. The camera is activated on the infotainment system monitor. The lens cover is only open during activation and therefore keeps the lens clean. Preparation with cable harness in the cab wall included. The camera is delivered in the cab. Camera bracket not included.

Side view camera mounted on the passenger side of the cab and connected to the infotain-ment system monitor. The monitor is switched off when the vehicle speed exceeds 35 km/h and switched on automatically when the direction indicator is activated on the passenger side, even at higher vehicle speeds.

Side view camera mounted on the passenger side of the cab and connected to the infotain-ment system monitor. The monitor is switched off when the vehicle speed exceeds 35 km/h and switched on automatically when the direction indicator is activated on the passenger side, even at higher vehicle speeds. Preparation for rear view camera for mounting on the rear wall of the cab. Can be used to see loading and unloading. The camera is activated on the infotainment system monitor.

Front view camera CornerEye connected to a separate 10" monitor. The camera is posi-tioned on the sun visor, and the monitor is positioned above the passenger door.

Ordering optionsTractors and trucksOption Alternative Variant

code

Camera system, FFU Rear view camera (x2) with lens cover 3832AD

Rear view camera with lens cover, cab wall 3832AE

Side view camera 3832AF

Side view camera + rear view camera with lens cover on cab wall

3832AP

Front view camera with 10" monitor 3832GA


Ordering options


Description

The camera is connected to the factory-fitted infotainment system monitor. The camera is fitted in the sun visor. Front view mirrors are also fitted if required by law.

The camera is connected to a separate, factory-fitted 7" monitor. The camera is fitted in the sun visor. Front view mirrors are also fitted if required by law.

The camera is connected to a separate, factory-fitted 10" monitor. The camera is fitted in the sun visor. The camera replaces the front view mirror.

The vehicle is fitted with a cable harness from the infotainment system to the rear wall of the cab where the cable harness is accessible behind a rubber sealing cap. The camera is sup-plied loose in the cab and fitted by the bodybuilder. Brackets are not included.

Infotainment system with built in 7" monitor

An extension cable is supplied in the cab

Option Alternative Variant code

Camera system, FFU Front view camera 3832E

Front view camera with 7" monitor 3832F

Front view camera with separate 10" monitor 3832G

Rear view camera, connected to the infotain-ment system monitor

3832K

Infotainment system 2 DIN with 7" monitor (premium) 5120B

Camera system, exten-sion cable FFU

5 metres 7551A


Ordering options


Description

Orlaco rear view camera connected to the infotainment system monitor. The rear view cam-era is positioned on the rear of the cab and has a shooting angle of 118 degrees. The cable harness from infotainment system to camera is prepared and fitted. Due to many different possible variants, the camera bracket is not included. Preparation for rear view camera on semi-trailer. The preparation is connected to the infotainment system monitor and activated when reverse gear is engaged. Camera not included. Spiral cable to semi-trailer is included and supplied in the cab.

Side view camera connected to the infotainment system monitor. The side view camera is mounted on the passenger side of the cab. The monitor is switched off when the vehicle speed exceeds 35 km/h. The monitor is switched on automatically when the direction indi-cator is activated on the passenger side, even at higher vehicle speeds. Preparation for rear view camera on trailer. When a camera is fitted and connected, it gives a better view when the vehicle is reversing. Electrical cable, camera cable connectors, support bracket and spi-ral cable (to connect to the trailer) are supplied. Connectors for connecting to the trailer are fitted on the trailer bracket behind the cab. Camera for the trailer is not included.

TractorOption Alternative Variant

code

Camera system, FFU Rear view camera on cab + preparation for rear view camera on trailer

3832AH

Side view camera + preparation for rear view camera on trailer

3832AK


Ordering options


Description

The vehicle is prepared with a cable harness from the infotainment system to a harness-to-component connector on the rear cab wall. A spiral cable for connection between the vehicle and semi-trailer is supplied in the cab. The harness-to-component connector is compatible with camera types with these part numbers: 2 545 694, 2 545 696, 2 545 698, 2 545 699, 2 545 700.

The vehicle is prepared with a cable harness from the 7" monitor to a harness-to-component connector on the rear cab wall. A spiral cable for connection between the vehicle and semi-trailer is supplied in the cab. The harness-to-component connector is compatible with cam-era types with these part numbers: 2 545 694, 2 545 696, 2 545 698, 2 545 699, 2 545 700.

Combination of 3832E and 3832L

Combination of 3832F and 3832M

Combination of 3832G and 3832L

Combination of 3832G and 3832M


Camera system, FFU Preparation for rear view camera on semi-trail-er

3832L

Preparation for rear view camera on semi-trail-er, separate 7" monitor.

3832M

Front view camera and preparation for rear view camera on semi-trailer

3832N

Front view camera with 7" monitor and prepa-ration for rear view camera on semi-trailer

3832P

Front view camera with 10" monitor and prepa-ration for rear view camera on semi-trailer

3832S

Front view camera with 10" monitor and prepa-ration for rear view camera on semi-trailer, separate 7" monitor

3832T


Ordering options


Description

Front view camera connected to the infotainment system monitor; the front view camera is delivered positioned on the sun visor. Rear view camera with lens cover that is connected to the infotainment system monitor and is activated when reverse gear is engaged. Prepara-tion for rear view camera on trailer containing camera with lens cover, extension cable, spi-ral cable and connection. The connection is temporarily fitted at the rear end of the frame while other parts are supplied in the cab.

The side view camera fitted on the passenger side of the cab and a rear view camera to the rear of the chassis; both are connected to the infotainment system monitor.

Rear view camera with lens cover connected to the infotainment system monitor. The rear view camera is activated when the reverse gear is engaged. Side view camera mounted on the passenger side of the cab and connected to the infotainment system monitor.

2 cameras with lens covers on the chassis, connected to the infotainment system monitor. The lens cover is lowered and protects the camera lens from dirt and dust when the vehicle is driving forwards. A camera is activated when reverse gear is engaged. This camera can be positioned on the lower part of the chassis and allows the driver to see the area behind the truck and the trailer coupling (if there is one). The other camera is activated with a but-ton on the infotainment system.

A rear view camera with lens cover on the chassis, connected to the infotainment system monitor. The lens cover is lowered and protects the camera lens from dirt and dust when the vehicle is driving forwards. The design also includes a preparation for rear view camera with lens cover for semi-trailer. Cable harness and harness-to-component connector for semi-trailer are fitted. Both the rear view camera on the chassis and the preparation are con-nected to the infotainment system monitor. Both are activated when reverse gear is engaged.

TruckOption Alternative Variant

code

Camera system, FFU Front and rear view camera + preparation for rear view camera on trailer

3832AC

Side view and rear view camera 3832AG

Rear view camera with lens cover + side view camera

3832AJ

2 rear view cameras with lens covers, posi-tioned chassis, connected to the infotainment system monitor

3832AL

Rear view camera with lens cover + prepara-tion for camera with lens cover for semi-trailer

3832AM


Ordering options


2 rear view cameras included on the chassis, connected to the infotainment system monitor. One of the rear view cameras has a lens cover. The lens cover is lowered and protects the camera lens from dirt and dust when the vehicle is driving forwards. The camera with the lens cover is activated automatically when reverse gear is engaged. This camera can be po-sitioned on the lower part of the chassis and allows the driver to see the area behind the truck and the trailer coupling (if there is one). The other camera is activated with a button on the infotainment system.

Front view camera CornerEye connected to a separate 10" monitor. The camera is posi-tioned on the sun visor, and the monitor is positioned above the passenger door. The camera is activated all the time. The front view camera does not replace the class VI front view mir-ror, in accordance with European legislation R46, but the front view mirror is delivered fit-ted.

The front view camera is fitted in the sun visor and the rear view camera is fitted to the rear of the chassis. The cameras are connected to separate monitors.

Description

Camera system, FFU Rear view camera with lens cover + rear view camera

3832AN

Front view camera with 10" monitor and rear view camera connected to the infotainment system alt. 2

3832UA

Front view camera with 10" monitor and rear view camera with 7" monitor

3832V



Ordering options



Ordering options


Description

The camera is connected to the factory-fitted infotainment system monitor. The camera is transport-mounted at the rear end of the chassis frame for final fitting by the bodybuilder. The accompanying cable harness extends 13 metres from the gearbox beam. It can be sup-plemented with Camera system, extension cable FFU (variant code 7551A).

Combination of 3832E and 3832AA

The camera is connected to the factory-fitted infotainment system monitor. The camera is transport-mounted at the rear end of the chassis frame for final fitting by the bodybuilder. The accompanying cable harness extends 13 metres from the gearbox beam. It can be sup-plemented with Camera system, extension cable FFU (variant code 7551A).

The camera is connected to a separate, factory-fitted 7" monitor. The camera is transport-mounted at the rear end of the chassis frame for final fitting by the bodybuilder. The accom-panying cable harness extends 13 metres from the gearbox beam. It can be supplemented with Camera system, extension cable FFU (variant code 7551A).

Combination of 3832E and 3832H

Combination of 3832F and 3832J

Combination of 3832G and 3832H

Combination of 3832E and 3832H. The vehicle is also fitted with preparation for a rear view camera on a trailer. The preparation consists of a cable harness from the infotainment sys-tem to a harness-to-component connector at the rear end of the chassis frame. The spiral ca-ble for connection between the vehicle and trailer is supplied in the cab from the factory. Trailer camera not included. The harness-to-component connector is compatible with cam-era types with these part numbers: 2 545 694, 2 545 696, 2 545 698, 2 545 699, 2 545 700.

2 sets of 3832H. Preparation with 2 cameras. The cameras are transported on the rear end of the chassis frame for final fitting by the bodybuilder. The accompanying cable harness extends 13 metres from the gearbox beam. One camera is activated by reverse gear and the other is activated by a button in the infotainment system.


Camera system, FFU Rear view camera with lens cover 3832AA

Front and rear view cameras with lens cover 3832AB

Rear view camera for trucks 3832H

Rear view camera for trucks with separate 7" monitor

3832J

Front and rear view cameras connected to the infotainment system

3832Q

Front and rear view cameras with 7" monitor 3832R

Front view camera with 10" monitor and rear view camera connected to the infotainment system

3832U

Front view camera and rear view camera, preparation for rear view camera full trailer

3832W

Rear view camera (2 no.) for trucks 3832X


Ordering options


The vehicle is fitted with a camera system consisting of 4 digital cameras, a control unit, a 7" monitor and electrical cables and camera bracket for fitting. The cameras are supplied in a plastic bag in the cab storage box. A document containing information on FFU customi-zation for the bodybuilder is placed in the cab. The Area View system must be calibrated after installing a camera on the bodywork.

Description

More information on calibration can be found on the Scania Vehicle Accessories website (https://accessories.scania.com).

Area ViewFFU, 360° digital

4 cameras (Front view camera, rear view cam-era, 2 side view cameras) with separate 7" monitor

9026A



Front and rear view cameras General

Documents

Transcript of Front and rear view cameras General