Engine Tools - BONCRAFT

47
Engine Tools Fan Clutch Service CY-283 4 pcs Fan Hub Wrench Set Open end size: 32- 36- 41- 46mm x 270mm(L) CY-283A Double End Thermo-Viscous Fan Nut Wrench - 32 x 36mm 2090 Ford Fan Clutch Tool Set When it comes to removing the fan clutch assembly on Ford engines, conventional wrenches are just too wide to do the job. With the No.2090,that is no longer a problem. While you hold the fan clutch pulley stationary with the clutch holder tool turn the fan clutch nut with the included wrench. It is that simple! *Available in two popular sizes. FT-090 Fan Clutch Wrench Kit HL-9042 BENZ & BMW Fan Service Kit OT-978 6 pcs Fan Clutch Wrench Set AT-825 Ford Diesel Fan Clutch Wrench Has a 1.7/8" (48mm) opening with special offset handle for use on the viscous fan lock-nut fitted to Ford vans and pickups with 7.3 Litre direct- injected turbo charged (DIT) diesel engines. * 1/2" Dr. * Length: 14.1/4" (360mm) OT-240 5 pcs Fan Clutch Wrench Set Set of 5 pcs included : Ford Thin Wrench 40, 54 & 72mm; Chrysler gas/diesel fan clutch crowfoot 68 & 76mm; Ford fan clutch holder 1-7/8" (47mm) Fan clutch wrench 83mm 2090B GM Fan Clutch Wrench This specially designed tool is used to loosen and tighten the fan clutch on 1996 and later GM trucks and vans. The unique design works with both 10mm & 13mm pulley bolts. 2090C Ford Fan Clutch Wrench Set * 2-1/8" (54mm) Fan clutch pulley holding tool * 1-7/8" (47mm) Left hand clutch nut wrench 2090A Ford Fan Clutch Tool Set 6500A Fan Clutch Removing / Installing Set 6500B Fan Clutch Removing / Installing Set 6500C 24 pcs Fan Clutch Removing/Installing Set & Serpentine Belt Tool & Acc.

Transcript of Engine Tools - BONCRAFT

Engine Tools Fan Clutch Service

CY-283 4 pcs Fan Hub Wrench SetOpen end size: 32- 36- 41- 46mm x 270mm(L)CY-283A Double End Thermo-Viscous Fan Nut Wrench - 32 x 36mm

2090 Ford Fan Clutch Tool SetWhen it comes to removing the fan clutch assembly on Ford engines, conventionalwrenches are just too wide to do the job. With the No.2090,that is no longer aproblem. While you hold the fan clutch pulley stationary with the clutch holder toolturn the fan clutch nut with the included wrench. It is that simple! *Available in twopopular sizes.

FT-090 Fan ClutchWrench Kit

HL-9042 BENZ & BMWFan Service Kit

OT-978 6 pcs FanClutch Wrench Set

AT-825 Ford Diesel Fan Clutch WrenchHas a 1.7/8" (48mm) opening with special offset handle for use on the viscous fanlock-nut fitted to Ford vans and pickups with 7.3 Litre direct- injected turbocharged (DIT) diesel engines. * 1/2" Dr. * Length: 14.1/4" (360mm)

OT-240 5 pcs Fan Clutch Wrench SetSet of 5 pcs included : Ford Thin Wrench 40, 54 & 72mm; Chryslergas/diesel fan clutch crowfoot 68 & 76mm; Ford fan clutch holder 1-7/8"(47mm) Fan clutch wrench 83mm

2090B GM Fan Clutch WrenchThis specially designed tool is used to loosen and tighten the fan clutch on 1996 andlater GM trucks and vans. The unique design works with both 10mm & 13mmpulley bolts.

2090C Ford Fan Clutch Wrench Set* 2-1/8" (54mm) Fan clutch pulley holding tool* 1-7/8" (47mm) Left hand clutch nut wrench

2090A Ford Fan Clutch Tool Set

6500A Fan ClutchRemoving / Installing Set

6500B Fan ClutchRemoving / Installing Set

6500C 24 pcs Fan ClutchRemoving/Installing Set &Serpentine Belt Tool & Acc.

Fan Clutch Wrench Engine Tools

FT-090A Fan Clutch Universal Pulley HolderServices thermostatic fan assemblies without various size holding wrenches.Applications for use in fan clutch removal include: Ford trucks w/2.8L, 2.9L, 3.0L,4.0L, 4.9L, and 5.0L engines.Dodge trucks w/3.9L, 5.2L, 5.9L, 8.0L and V10engines. GM trucks w/4.3L, 5.0L and 5.7L engines. Jeeps w/5.2L engine

HL-9010 BENZ - Fan Clutch Wrench* Replaces fan clutch assembly on Mercedes Benz vehicles. Slim shaft handles let youeasily work in light space.

FT-090-3 3 pcs Fan Clutch Wrench SetIncludes Universal Pulley Holder and Fan Clutch Wrenches. - Ford trucks w/2.8L,2.9L, 3.0L, 4.0L, 4.9L, and 5.0L engines. - Dodge trucks w/3.9L, 5.2L, 5.9L, 8.0L,and V10 engines. - GMC/Chevy trucks w/4.3L, 5.0L, and 5.7L engines. - Jeepsw/5.2L engines. * Universal pulley holder * Wrench (40mm) * Wrench (36mm

6500A-3683 Ford Diesel Fan Clutch Wrench SetWrench Openings - Long: 36mm (1.417"), Short: 83mm (3.250").

FT-238 Audi/VW Fan Clutch Holding* Audi & VW Fan Clutch Idler Pulley Holding Tool is a 4 pin wrench design that holds thepulley of the viscous fan clutch. * Its long handle design gives the technician plenty of room tohold the wrench securely. * (32mm) wrench is a perfect match for this fan clutch service. *AUDI 1996-2001 A6 2.6L V6. * VW 1998 and Later Passat 3.0L V6.

CY-283D Benz & BMW Viscous Fan Hub Spanner -32mmFor removal of thermo, viscous fan hubs. Cranked for easy access.Size: 32mm; App.: BMW 316i, 520i, 525i, 530i, 535i, 730i & 735i Ford CAPRI, sierra GRANADA 2.0 & 2.8 Ford transit 2.0 1986-90. (with viscousfan) LCx2.0, LCT 2.0, 2.5 diesel 1980-90, LCx2.5d & LCY 2.5d

HL-9008 BENZ - Fan Belt Service WrenchSpecial designed 3 holes to hold the stud on fan clutch assembly found on MercedesBenz vehicles to allow release of lock nut. Slim handle for tight space operation.

CY-283E Benz & BMW Viscous Fan Hub Spanner -36mmFor removal of thermo, viscous fan hubs. Cranked for easy access. Size: 36mm, App.: FORD, GRANADA 2.4 & 2.9. GM CARLTON, MOANTA &SENATOR. MERCEDES BENZ

HL-9043 BENZ - Fan Belt Service WrenchThis universal tool has been designed to service Mercedes Benz;Nissan Quest;Mercury Villager Radiator fans and pulley belts. The three-in-one design allowsservicing three separate areas of repair. All of which require a specialty tool due totheir confined locations. This special wrench can be used for loosening the A/C idler pulleytensioner lock-nut for A/C belt Adjustment or replacement 8M/M & 10M/M bit included.

OT-924 Fan Clutch Wrench Set for FORDRemoves Fan Clutch on Most All Ford Vehicles. The double-ended wrench and smallholding wrench work on 2.8, 2.9, 3.0, 4.0 and 4.9 liter engines. The larger open-endwrench and larger holding wrench fit 6.9 and 7.3 liter diesel engines.

6500A-3658 Ford Fan Clutch Wrench SetUse with 1/2" square drive tools and torque wrench. Refer to Ford factory servicemanual for torque specifications and thread direction. Wrench Openings - Long:36mm (1.417"), Short: 58mm (2.283").

Engine Tools Cooling system Tools

RD-3194 3 pcs Hose Pinch-off Pliers Set* Shuts off flow through vacuum lines, fuel lines, coolant lines, etc. * Cockingratchet mechanism holds pivoting jaws tightly in place. Heavy-duty swivel jawspivot to assure parallel pinching. These tools are available separately: 8", 10"12"SA-9203 3 pcs Hose Line Clamp setSmooth round jaw edges prevent damage to internal hose reinfocement; Qickand simple, one hand use; made from durable glass reinforced nylon.Size range: Large: 22-60mm, Midium : 22-42mm. Small: 11-19mmWH-737S 3 pcs Hose Line Clamp setSmooth round jaw edges prevent damage to internal hose reinfocement; Qickand simple, one hand use; made from durable alunimum.Size range: Large: 22-60mm, Midium : 22-42mm. Small: 11-19mm

FT-447 Oil Cooler Line PlierRelease the hydraulic cooling lines that connect to the transmission.• Applications: BMW E46, E53, E65, E66, E85, R50, R53.

OT-224 Freeze Plug Installation Kit* Excellent for working around heaters, exhaust systems, motor mounts, andstartersl * "Speedy driver" even installs freeze plugs in the back of the engineblock on most applications * Jobs that normally take 5-6 hours can now becompleted in 1-2 hours with "speedy driver".

BT-040 IdIer Pulley Wrench*For adjusting of the toothed belt at the automatic tensioning pulley; *Especiallyfor VW Polo Diesel,AUDI 100 since 1991, AUDI A6 with 2.5 l TDi engine. * size:32 mm' *Special steel *Surface mat chrome-plated,handle plastic coated

AT-595 Coolant Temperature Sensor Socket For remover and installation of coolant temperature sensor; Fits Nissan cars andtrucks with 3.OL V6 engines; * Similar design to factory tool.

FT-565 Universal Pulley Holder (U.S.A Patented)* Adjustable jaws fit various water pump pulley bolt patterns. * Jaws lock in placeto securely hold water pump bolts. * Long handle offers leverage for extra torque.

CY-323 GM Water Pump R&R SocketSpecially designed for use on 1993 - current Northstar 4.6 liter, 1997 - currentAurora 4.0 Liter. 1/2" Drive size.

AT-565 GM Heater Line Disconnect ToolDisconnects heater line from engine block/thermostat housing. Fits 1991-current GM 3.1liter, 3.4 liter and 3.8 liter (3800) engine.

AT-205 Heater Hose Disconnect ToolRemoves heater hoses with 1/4" or 5/8" quick disconnect couplings from rearheater core on 1987-currect Dodge Caravan and Plymouth Voyager vans. Alsogets into difficult access area next to firewall on 1986-current Ford Aerostar vans.

AT-205A Ford Aerostar Heater Hose ToolUse tool to remove heater hose from heater core tube without damaging coupling, retainer orhose. It fits Ford 1986 to current Aerostar vans with 5/8" to 3/4" heater hoses and quickdisconnect couplings. Its extension handle allows for easy access to coupling.

Fuel line disconnectorEngine Tools

CJ-400A Transmission Cooler Line & Fuel Line Disconnect ToolRemoves push lock connectors found at both the radiator and transmission. Used on 1983through current Ford, and the 1982 Lincoln Continental overdrive transmissions. Tool slidesdown transmission cooler spread the plastic clip apart for easy removal.

CJ-400C Chrysler Quick Disconnected Coupler Tool

CJ-400 Ford/GM Quick Disconnected ToolFord CFI fuel lines w / hair pin connectors; universal for radiator to transmissionoil cooler lines; '87 & newer Olds. Toronado; Buick Riviera & Regatta; CadillacEldorado, Seville, & Concours: '89 & newer GM 1/2-ton, 3/4-ton, and 1-ton pickups.

2160 16 pcs Rocker Stopper Oil Plugs kitPlug oil holes in ball-joint type rocker arms. Spring steel clips with gaskets stopsplashing, squirting hot oil while you adjust clearance. Designed for cars withhollow, oil-fed push rods.

FT-766 Fuel Pump Gas Tank Retaining Ring Removal ToolTo remove or replace fuel pump retaining rings: * Loosen lock nut on tool andadjust length of tool so slot in ears fits over teeth in plastic ring. * Tighten lock nutand loosen or tighten plastic ring using 1/2" extension and ratchet wrench.

AT-515AB Ford A/C & Fuel Line Lock Coupling ToolSet of both : AT-515A Fuel Line Quick Disconnect Tool AT-515B Spring Lock Coupler Tool

AT-515D Ford A/C & Fuel Line Lock Coupling Tool Kitset included: Fuel Line Quick Disconnect Tool; Spring Lock Coupler ToolFord Fuel Line Coupling Tool; Ford/GM Quick Disconnected Tool

CJ-570 Ford Fuel Line Coupling ToolThe best way to get easy, frustration - and damage-free fuel line separation. The tool'sfingersslip into the fuel line coupling, depressing the re taining collar as they go. The toolworks on 1990 and newer Ford Rangers and Explores having 4.0L, 6-cylinder engines.

AT-525 Ford/GM Fuel Line Disconnect Tool Set1992 & newer Chev, Lumina & Monte Carto: Pont, Grand Prix; Olds Cutlass Supreme; BuickRegal (all w/ABS); 1988 & newer Ford pockups (at fuel sending unit).

AT-535 Chrysler Fuel Line Disconnect Tool1994 & newer Chrysler LH vehicles, other Chrysler vehicles with quick connect fuellines.

FT-155 Ford 7.3L Fuel Cap ToolDesign allows for easy removal and installation of Ford 7.3L Diesel fuel caps and other Dieselfilter systems using the same configuration. Works with fuel caps from 1995 to present.Improves ability to remove and install caps where access is a problem. Patented.

FT-435 Cummins Diesel Fuel Injector Remover KitKit contains a fuel injector connector tube remover and fuel injector puller. The fuelinjector connector tube must be removed before removal of the injector, or both willbe damaged. Application: 1998-1/2-newer Dodge pickups and vans with 5.9L 24-valve Cummins diesel turbo engine.

FT-309 Fuel Line PliersSuitable for VW-Audi, Fiat, GM, Opel, Mercedes etc. e.g. Mercedes M-Class withPetrol engines. For removal and replacement of the connections on the in-line FuelFilter. Required when replacing the Fuel Filter or during engine repairs. Removal ofConnector: Pull the connector backwards with the Pliers. Length: 240 mm

Engine Tools Fuel system service

CJ-400B Disconnect Tool SetTwo popular disconnect tools in one set gives you the versatility to quicklyseparate the quick connectors found on everything from radiators to transmission andpower steering lines. The quick disconnect coupler tool, No. 400 works on late modelFord and GM vehicles by sliding down the line and into the connector, -Works on 1986and newer Ford Tauruses and Mercury Sables with an AXOD, AOD, or ATXtransmission.

FT-618 Fuel Feed Pipe PliersApplication: Opel/Vauxhall, Fiat, GM, VW etc.For undoing quick release connections on fuel feed pipe lines.

BT-025 Fuel Tank Sender Spanner (adjustable)Universal application. For removing and replacing the Plastic Retaining Ring onthe sender Unit on Fuel Tanks.BT-025A Tank Sender Spanner Φ110-170 mm. Drive 24 mmBT-025B Tank Sender Spanner Φ80-122 mm. Drive 24 mm

BT-025C Fuel Tank Sender Spanner (adjustable)Universal application. For removing and replacing the Plastic Retaining Ring onthe sender Unit on Fuel Tanks. ( triple legs )Tank Sender Spanner Φ75-160 mm. Drive 24 mm

CY-006 TOYOTA Fuel Pipe Line Nut Wrench.Used for TOYOTA,HONDA bolts of fuel filter cup. 3/8" Dr. Full length94mm, suit for narrow place. Special design with cover for holding the nutcompletely and prevent slipping. Available size: 14mm & 17mm

HL-9029 BENZ - W210 Fuel Tank Cup WrenchThe tool to removal the plastic fuel tank cup .Apply on BENZ type W210

SF-9037 HINO Oil Mist Separator Wrench - 107mm* HINO oil mist separator wrench(8RIBS,107mm). ‧Using the oil-waterseparator wrench. ‧Looped handle. ‧Japanese truck repair tool.Application range:HINO truck year 2003~2006 or after year 2010.‧Genuine no: 103251,S23401-11840-A

CY-533 Adjustable Fuel Tank Lid RemoverTo adjust from the middle track. You can use on all kinds of vehicle with salientfuel tank lid. Applicable:Benz, BMW, European cars, etc.

SF-9039 FUSO Oil Mist Separator Wrench - 109mm‧Fuso oil mist separator wrench (8RIBS,109mm). ‧Using the oil-waterseparator wrench. ‧Looped handle. ‧Japanese truck repair tool. ‧Specialtytools. Application range:FUSO 380 over 17 tons (Engine no 6M70) and bus.Mitsubishi all NEW CANTER eco-4 3.5 , 6.7and 6.9tons.

FT-6376 Fuel Filter Key Ø109Suitable for new Opel vehicles. The fuel filter key is required to removeand install the fuel filter cap when replacing the fuel filter cartridge.Drive: 3/8” Profile: Ø 109 mm, 6 Rillen

FT-6378 Fuel Filter Key Ø109Suitable for Peugeot, Citroen, Renault etc. The fuel filter key is required toremove and install the fuel filter cap when replacing the fuel filter cartridge. Drive: 3/8” Profile: Ø 109 mm, 8 Rillen

Fuel system service Engine Tools

HL-9032 BENZ - W202 Fuel Tank Cup WrenchThe Special tool to removal the plastic fuel tank cup.* Applicable:BENZ (W202)

HL-9045 Fuel Tank Lid DissemblerThe tool helps to remove the fuel tank lid easily. Used with a 16mm spanner orby hand to drive.

FT-636 Oil Service Wrench* For the oil filler and oil drain plug gearbox, differential, oil pan e.g. on ALFAROMEO, FLAT, LANCIA. * For 12 mm inside hexagon screws.HL-9026 8 & 10mm Oil Service WrenchChrome-vanadium, chrome-plater with 8 and 10 mm outside square drivefor various French passenger cars, oil drain plug on oil pan,gearbox,diferencial.FT-776 1/2" & 3/8" Sq. Drain Plug Wrench1/2" & 3/8" male square for removing drain plugs on oil, transmissions,differentials. Heavy-duty construction, tempered to withstand the rigors ofconstant use.

CY-2592 12 pcs 3/8”Dr. Drain Plug Ket Set3/8"Dr. x 165mm Sliding T bar; 3/8"Dr. Hex : 8-9-10-12-14-17mm & 3/8"3/8"Dr. Square : 8-11-13mm & 3/8”; CR-V steel , Mat Finished;

CY-2593 14 pc 3/8"Dr. Master Drain Plug Key SetBMW, LANCIA, RENAULT, CITROEN, MAZDA, SAAB, FIAT, MERCEDES,TOYOTA, FORD, NISSAN, VAUXHALL/OPEL, HONDA, PEUGEOT, VOLKSWAGEN3/8"Dr. Hex : 8-9-10-12-14-17mm; 3/8"Dr. Square :7-8-11-13mm & 5/16”.3/8”3/8"Dr. Female Square: 10mm; 3/8"Dr. Triangular

FT-437 Oil Drain Plug Repair KitFor threads M14×1,5, Includes a special thread borer, 5 Threaded Plugs, 5Washers.

CY-2591 6 pcs 1/2”Dr. Drain Plug Key Set size : 8-10-12-14mm & 1/2" & 3/8". CR-V steel , Mat Finished

CY-259 Metric Sump Plug KeySump plug key & drain/plug keyFor 8 different int. head size : Square10, 11, 12, 13, 14, 15mm; Hex:14, 17mm

CY-2594 18 pcs 3/8”Dr. Master Drain Plig Key setBMW, LANCIA, RENAULT, CITROEN, MAZDA, SAAB, FIAT, MERCEDES,TOYOTA, FORD, NISSAN, VAUXHALL/OPEL, HONDA, PEUGEOT, VOLKSWAGEN3/8"Dr. Hex : 8-9-10-12-14-17mm; 3/8"Dr. Square :7-8-10-11-12-13-14mm & 5/16”.3/8”3/8”Dr. Female Square : 10mm; 3/8”Dr. Triangular; CR-V steel, Mat Finished

CY-2595 21 pcs 3/8”Dr. Master Drain Plig Key setapply for BMW, Lancia, Renault, Citroen, Mazda, SAAB, Fiat, Merceds, Toyota,Ford, Nissan, VAUXHALL/Opel, Honda, Peugeot, Volkswagen: 3/8”Dr. SlidingT-bar; 3/8”Dr. Hex : 8-9-10-12-13-14-17mm; 3/8”Dr. Square :7-8-10-11-12-13-14mm & 5/16”-.3/8”; TX socket: T45SPL socket: M16, 3/8”Dr. Female Square:10mm; 3/8”Dr. Triangular; T-Handle

Engine Tools Injector service

CY-2596 18 pcs 3/8”Dr. Master Drain Plig Key set3/8”Dr. Hex : 8-9-10-12-14-17mm; 3/8”Dr. Spline (Tamper) : M16;3/8”Dr. Square :7-8-10-11-12-13-14mm & 5/16”-.3/8”3/8”Dr. Female Square : 10mm; 3/8”Dr. Triangular

FT-437C Oil draining screw repair setComplete with fine-thread tap as well as 5 new oversize oil draining screws andsuitable aluminium seals for the given thread size; 33 pcs, M15 - M18 - M20

FT-780 Oil Drain Plug WrenchSize: M14 x T45 x 300mm; Universal application.

FT-437B Oil Pan Repair Master Set*Universal applications e.g. for: Audi, BMW, Citroen, Daimler-Benz, Ford, Fiat, Honda,Mazda, Mitsubishi, Nissan, Opel, Peugeot, Porsche, Renault, Saab, Seat, Skoda, Toyota,Volvo, VW etc. Consisting of: Special Taps M13x1.5; M15x1.5; M17x1.5; M20x1.5; Oildrain plug gasket with aluminum M13x1.5 x 5pcs; M15x1.5 x 5pcs; M17x1.5 x 5pcs;M20x1.5 x 5pcs

CY-286 Injector Nozzle Puller with Slide HammerFor removing adapted tight common rail injectors without having to disassemblecylinder head. use for Mercedes-Benz CD engines 611.612.613….etc. Injectionpuller with impact hammer, injection nozzles that do not fit very tightly can bepulled out without needing to take them apart or remove the cylinder block.

FT-019 Injector Nozzle Puller - Mercedes CDISuitable for Mercedes CDI engine OM 668 e.g. A-Class; The injector nozzlepujller makes it possible to remove even nozzles that are a very tight fit in thecylinder head, without the cylinder head having to be removed from the engine.

OT-343 Mack Fuel Injector Nozzle ToolHere's a handy tool for removing or installing injector nozzles on Mack E-6 4 VH and E-9 4VH four-valve engines. The puller threads directly into nozzle holder, mechanical screwpower does the pulling while a cylindrical guide holds the injector steady.

ST-655 Bosch Nozzle SocketHere's a helpful multipurpose tool for removing or installing injector nozzles. You use theinner socket to hold the nozzle stationary, and the outer socket to loosen or tighten thenozzle's gland nut. Works on Bosch KDEL 21mm injector nozzles used in John Deereengines.

CY-145I 33 pcs Glow Plug Thread Repair KitDesigned to repair the thread for the glow plug threads. Tap size:M8 x1.0, M10x1.0, M10 x1.25, M12 x1.0, M12 x1.25, M14 x1.25; Thread coil size: ‧2-Threadcoil driver; M8 x1.0 (I) - M10 x1.0 (E), M10 x1.0 (I) - M12 x1.0 (E),M10 x1.25 (I) - M12 x1.25 (E), M12 x1.25(I) - M14 x1.25 (E)

CY-286A Injector Nozzle Puller with Slide HammerFor removing adapted tight common rail injectors without having to disassemblecylinder head. use for Mercedes-Benz CD engines 611.612.613….etc. Injectionpuller with impact hammer, injection nozzles that do not fit very tightly can bepulled out without needing to take them apart or remove the cylinder block.

CY-286C Injector Nozzle Puller with Slide HammerA Tool Designed for safe, controlled removal of clamps attaching the exhaust tomanifold; ‧Special design provides LEVERAGE to expand the strong springclamps. ‧For Volkswagen

Glow Plug Tool Engine Tools Injector service

FT-047C Injector Puller Set - Mercedes CDIThis six piece puller set has been especially designed for removing stubbon injectorson Mercedes Benz vehicles fitted with CDi engines.

FT-047D Injector Nozzle Tool Set - Mercedes CDI enginesSuitable for Mercedes CDI engines OM 611, 612, 613, etc.The FT-047D injector nozzle Tool set (comprising nozzlepuller, nozzle puller , milling cutter, compressed air adapter, threadtap and plastic case) makes it possible to remove the injector nozzles correctly.

FT-047D Injector Nozzle Tool SetMercedes CDI engines (German Utility Model); Suitable for Mercedes CDI enginesOM 611, 612, 613, etc. The FT-047D injector nozzle Tool set (comprising nozzlepuller, nozzle puller , milling cutter, compressed air adapter, thread tap and plasticcase) makes it possible to remove the injector nozzles correctly.

FT-047E Glow Plug Tool Set - Mercedes CDI enginesSuitable for Mercedes CDI engines OM 611, 612 and 613.; The glow plug tool set FT-047E enables the correct removal of burnt and/or stuck due to corrosion or torn offglow plugs as well as the repair of the glow plug retaining thread. The cylinder headdoes not have to be removed. Note: Screwing the compressed air adapter into theinjector nozzle bore and injecting compressed air into the combustion chamberprevents dirt and metal particles from entering the conbustion chamber

CY-166 Glow Plug Tool SetDiesel Engine requires GLOW PLUG for combustion process in enginecylinder. The heating element in glow plug heat up and drive the cylindersgradually. But the heating elements are very delicate, and require special tool forremoving the glow plug.

FT-047E Glow Plug Tool Set - for Mercedes CDI enginesSuitable for Mercedes CDI engines OM 611, 612 and 613. The glow plug tool set FT-047E enables the correct removal of burnt and/or stuck due to corrosion or torn offglow plugs as well as the repair of the glow plug retaining thread. The cylinder headdoes not have to be removed. Note: Screwing the compressed air adapter into theinjector nozzle bore and injecting compressed air into the combustion chamberprevents dirt and metal particles from entering the conbustion chamberAdvantage: • Large time saving and cost saving • Clean working methods.

FT-047G Injector Puller for VAGmodels with Tdi-PD systems; Features: Specially designed for Tdi-PD systems; .Slidehammer with special PD puller; .Supplied with Vice Clamp suitable for use withtraditional injectors also

FT-019A Injector Nozzle Puller - Mercedes CDISuitable for Mercedes CDI engine OM 668 e.g. A-Class; The injector nozzle pujllermakes it possible to remove even nozzles that are a very tight fit in the cylinder head,without the cylinder head having to be removed from the engine.

FT-059AH 4pc Diesel Injector Removal Set-Delphi & BoschSpecifically designed for removing Delphi/Bosch diesel injectors using a SlideHammer(492mm) with 5/8" UNF thread. Adaptors can also be used with an air tool toloosen the injectors by vibration. Set of 3 adaptors plus a special tool for removing theinternal part of Bosch injectors.

Injector Service Engine Tools

CY-141 CDI Glow Plug Tool•For unscrewing and disassembly of glow plugs in the cylinder head, especially forglow plugs that are stuck because of carbonization remains. •Cylinder does not neetto be removed any more. •Fits all mercedes 10mm glow plugs, engine codes 611-612-613 etc.

CY-158 Diesel Injection Pump Puller for BMWThis tool is specifically designed for holding the sprocket / chain in place whendisassembling the VP44 injection pump and high pressure pump. ‧Common railfitted to BMW engines: 318D / compact (E46), 320D /TD compact(46),330D(E46), 525D(E39), 525D(E60/E61), 530D(E39), 530D(E60/E61),535D(E60/E61), 730D(E38) ,X53.0D(E53)

OT-323 Fuel Injector Nozzle Puller* Designed to remove the pencil-Type fuel injector nozzles on gricultural and constructionengines. * Slide hammer action gives a straight, pull without damaging components. * ForCase, Caterpillar, GM, John Deere, Waukesha, and White diesel engines

CY-127 Copper Washer Removal Tool for Diesel Injector•Size: inner hole 7 •Length: 230mm•Collet type easy to holding the copper washer

SF-8011 BMW Common Rail Injectors Tool set‧Complete set for removing BMW CR Injectors without dismounting the cylinderhead. ‧Equipped with a blower adapter to clean the injector seats. ‧Boschinjectors: common rail injectors mounted on BMW; Application Engines: BMWCommon Rail : M47TU, M57, M57TU

SF-8013 BMW Common Rail Injectors Removing & Cleaning tool set - Diesel‧Complete set for removing BMW CR Injectors without dismounting the cylinderhead. ‧Equipped with a blower adapter to clean the injector seats.‧Bosch injectors: common rail injectors mounted on BMW; Application Engines:BMW Common Rail : M47TU, M57, M57TU, M87, M87TU

CY-216 9 pcs Injector extractor SetThis high quality tooling is designed for the removal of stuck and seized injectors.‧Material: S45C steel. ‧Total Length: 350mmL‧Contents: Slide hammer: 1.75Kgs. Adaptor: M17 x 1.0; Adaptor: M27 x 1.0 forBosch injector nozzle. Adaptor: puller w/M12 x 1.75P.

SF-8009 VW. AUDI Injectors Remover set (FSI)‧Use " U" sleeve or two jaws hook to fix the injector and then pull out with slidehammer; Application range: VW, AUDI 【FSI】engine.

SF-8003 Universal Remover For JTD On Diesel Engines‧Universal Injector Remover with 4 adjustable feet for JTD Diesel Engines.‧Remover for common rail injectors.Application Models: FIAT, ALFA, OPEL, SAAB, SUZUKI Engines: JTD

SF-8005 Extractor Specific Tool set For Mercedes Injector‧Specific for MERCEDES (C/E/S CLASS, VITO) INJ. Complete W/ SOCKETfor dismounting the EL. Connection. ‧MERCEDES / BOSCH Injector Solution.‧Extractor specific for MERCEDES injectors, complete with socket fordismounting the electrical connection.

Injection Service Engine Tools Serpentine Belt tool

FT-059 4 pcs Diesel Injector Removal SetSpecifically designed for removing Delphi/Bosch diesel injectors using a SlideHammer with 5/8" UNF thread. Adaptors can also be used with an air tool toloosen the injectors by vibration. Set of 3 adaptors plus a special tool forremoving the internal part of Bosch injectors.

FT-327 Injection Pump Pulley ExtractorTo loosen the injection pump pulley from the shaft.Application: VW-Audi, Seat, Škoda, etc.

FT-606 Double Offset Ratchet Wrench* For install/remove glow plugs e.g. diesel engines VW, BMW, AUDI, RENAULT. * Forglow plugs between the motor unit and the diesel injection pump.FT-606-810 8mm x 12PT x 10mm x 12PT x 300 mm Long.FT-606-812 8mm x 12PT x 12mm x 12PT x 300 mm Long.

FT-646 Diesel Injection Pump Wrench13mm - 12PT 90 degree crank.; * For the fastening screws at the injectionpump, when replacing the toothed belt or adjusting the injection start.* Application on 1.6∣4-cyl. Diesel engine AUDI 80, VW Golf, Jetta, Caddy,Passat, Santana.

FT-387 Injection Pump Adjustment ToolSuitable for Renault, Mitsubishi, Opel/Vauxhall and Volvo 1.9 direct-injection dieselengines (F8Q and F9Q) with adjustable injection pump wheel. e.g. RenaultMegane/Scenic, Kangoo; Mitsubishi Carisma; Opel Arena and Volvo S40/V40.; Theinjection pump to the camshaft (start of delivery) can be adjusted with the injectionnozzle adjustment tool in conjunction with the KL-0129-1 A set of tools and the requiredlocking tools.CJ-410 Serpentine Belt Tool SetReleases tension on Serpentine Belts with Spring Loaded Idler Pulley. This tool is usedto remove and install belts on serpentine belt systems using the spring loaded idlerpulley. Fits idler pulleys requiring 13mm, 15mm, 16mm, 18mm, or 3/8" square drivesocket size, which are on most all domestic applications. Select proper socket size andposition tool idler arm, ( handle only is used for 16mm applications.) pulley or pull torelieve tension.

CY-158A Diesel Injection Pump Puller for M7 BMWROVER 75, LR Freelander, Vauxhall/Opel Omega B

CY-158B Injection Pump Puller - M41/M51 BMW3 Series E36, 5 Series E34 and 7Series E38

CY-217 5 pcs Diesel Injector Seat Cutter Set‧Re-face the diesel injector seat in order for the new or reconditioned injectorto be fitted correctly. Clean and re-cutting of injector seat. Avoid a high risk of"blow-by" occurring cause of the build up of carbon deposits and the effects ofcorrosion. ‧Application for all modern common rail diesel engines. ReamerSize: 15 x 19mm, 17 x 17mm, 17 x 19mm, 17 x 21mm.

CY-217E 8 pcs Diesel Injector Seat Cutter Set15 x 19mm flat reamer -- Universal applications17 x 17mm angled reamer -- Mercedes-Benz CDI17 x 17mm flat reamer -Delphi/Bosch injectors (BMW/PSA/RENAULT/FORD)17 x 19 mm flat reamer -- Bosch injectors (Mercedes CRD)17 x 21 mm angled reamer-- Fiat / Iveco.※T handle x 1pc ※Injector Cleaner ※ Pilot post x 1pc

Reaction Wrnech Engine Tools Serpentine Belt Tool

HL-9064 Serpentine belt servicing tool set* Combines the patented innovation of GearWrench with the requirements of theSerpention Belt removal tool to provide the user with the best possible combination.* Provides coverage for all major vehicles with serpentine belt configuration. Theversatility and strength of the Gear Wrench allows for unlimited access to serpentinepulley tension arms with added attachments for unlimited coverage.

CJ-410C Serpentine Belt Tool SetApplications: 13mm Socket-GM Quad Four Engine13mm Socket (on handle)-Late model GM Quad Four Engine14mm Socket-1.9 Liter Saturn; 15mm Socket-Some GM and Chrysler15mm Socket (on long extension)-3.3 Liter Chrysler16mm Socket (on handle & long extension)-3.8 Liter Ford16mm Socket- 4.0 Liter Ford; 18mm Socket - GM 3800 Engine3/8" Square Drive Socket - 3.1 Liter GM; 1/2" Square Drive Socket - Late GM &Ford

HL-9016 Ratcheting Serpentine Belt Wrench KitService approximately 90% of all vehicles equipped with spring-loaded serpentinebelt tensioners. For use when servicing serpentine drive belts or any belt-drivenaccessories. Specifically designed to fit into tight areas. Ratcheting action allowsquick an easy positioning of wrench driving end for tensioner access from any angle.

CY-124A Reaction Wrench for European Automobiles• For Locking the pulley on the WATER-PUMP on VW, AUDI.

FT-357 Reaction WrenchFor tightening timing belts with limited access - the wrench can beactivated from a variety of angles to enable it to be used in confinedspaces. Drive: 3/8“ or by pin. Length: 47 mm ; Depth: 32,5 mm

BT-030 Flywheel Locking Tool (universal)Necessary for dismanting or re-assembling flywheels,clutch pressure platesand belt pulley.(Length 250mm)

CY-124 Reaction Wrench• For Locking the pulley on the WATER-PUMP on VW POLO, GOLF, PASSAt AUDI80/A4 • The 1/2" drive in the tools handle enables an extension of the tool by e.g. aratchet • Easy loosening of stubborn bolts on the water-pump pulley. • L: 250mm

FT-319 Reaction Wrench for Crankshaft Pulley(German Utility Model); For VW-Audi 4 and 5 cylinder engines withand without harmonic damper. To provide a reaction onto the crankshaftfront pulley so that the central pulley bolt may be lossened or tightened.Required for timing belt changes, oil-seal replacement and during enginerepairs. Advantage: By using the 2 extension handles, the loosening andtightening of the central crankshaft pulley bolt can be undertaken by a singlemechanic.

FT-397 Reaction WrenchFor V-ribbed belts. When changing the poly-V belt the permanent belttensioning roller can be loosened with the reaction wrench. Application: VWPolo, Golf, Passat, T4 and Audi. Drive: 1/2"

FT-407 Reaction WrenchFor V-ribbed belts. When changing the poly-V belt the permanent belttensioning roller can be loosened with the reaction wrench. Application: VWPolo, Golf, Passat, T4 and Audi.

Oil Filter Wrench Engine ToolsFT-417 Reaction WrenchFor tensioning multi-vee belts, equipped with hardened and mill pins which allow thebelt tension to be achieved at the alternator. The milled pins are designed not to slipout of the holes in the alternator. For VW-engines on which the multi-vee belts canonly be tightened at the alternator. 1/2"Dr. Cap. (pin to pin): 157mm

OT-949 16 pcs Cap type Oil Filter Wrench Set* Durable light weight polyacetal copolymer; *High tensile strength* Visible bright color, high impact quality; * No heat distortion up to 230°F(110℃) * Steel square drive insert for non-slip 3/8" drive

CY-268B 5 pcs 3/8" Dr. Oil Filter Socket setChemically blackened, chrome vanadium steel socket. Low profile designenables use on cartridge style filters.Set included Size: 3/8" Dr. x 24- 27- 32- 36- 38mm x 30mm(L) x 6 PT.

CY-268A 4 pcs 3/8" Dr. Oil Filter Socket setsocket : 3/8" Dr. x Length : 30mm(L) x 6 PT. 27mm apply for (MercedesA Class) 32mm apply for (GM/Opel,Astra G, Corsa B, Zafira.)36mm apply for (BMW, Ford, Mondeo 2.0D Duratorq, Transit 2.0 &GM/Opel,) 38mm apply for (Vauxhall Vectra 2.0D)

HC-65300 30 pcs /set HC-65240 24 pcs /set HC-65160 16 pcs /set

HC-65909 9 pcs Cuptype Oil Filter Wrench Kit

HC-65900 9 pcs Cup typeOil Filter Wrench Kit

HC-65100 15 pcs Cuptype Oil Filter Wrench Kit

FT-380 1/2"Dr. Oil Filter Wrench

HC-65770 7 pcs Cuptype Oil Filter Wrench Kit

HC-65666 7 pcs Cup typeOil Filter Wrench Kit

HC-65010 5 pcs Cup typeOil Filter Wrench Kit

Engine Tools Oil filter service

UG-B04 1/2”dr. Chain Oil Filter WrenchFits 1/2” drive; Fully adjustable from 120mm(4-3/4”).1/2” Square drive with 22mm Navel Hexagon adapter.

BT-025D Wire type Oil Filter WrnechUniversal application. SpannerΦ75-100 mm.

FT-935C Double Chain Oil-Filter WrenchFT-935C-1 Suitable for filter Ø 60~115 mm.FT-935C-2 Suitable for filter Ø 60~170 mm.

FT-935D Oil Filter Chain Wrench• For removing oil filters and for the operation of the granulates cartridge oncommercial vehicles with compressed air dryers • Even in areas with restrictedaccess • With chain • j drive 12.5 = 1⁄2” • Special steel• DBGM – German registered utility model

CA-8906 Strap Wrench for Oil Filter‧For removal of oil filters in car engines.‧Special tool steel body, mat chrome plated.‧High-strength fabric strap, ∮160mm; High quality plastic handle.

FT-935 Hinged Chain Wrench For Oil Filters* Burnished and chrome finish.FT-935A Suitable for filter Ø 60~105 mm. Length 350mmFT-935B Suitable for filter Ø 60~160 mm. Length 520mm

FT-998A Swivel Jaw Filter Wrench Plier• Jaws swivel 90° in either direction to access most oil and fuel filters.• Jaws adjust to 4 positions, (30° increments) to fit most applications.• Slip-joint handle offers a big range from 2-1/4" to 4-3/4" (57mm to120mm).• Sure grip teeth prevent slipping. • Cushioned handles provide comfort.

CA-8908 Adjustable Oil Filter Wrench

CA-8913 Oil Filter Strap WrenchSlip strap wrench onto body of oil filter. Remove by applying pressure andturning counter-clockwise. Heavy Duty Spring steel. For Domestic and ImportCars; Fits 3-7/16" to 3-3/4" Diameter Filters for Removal Only

CA-8175 Oil Filter Wrench pliersHardened drop forged CR-V steel tool removes stubborn filters 60m/m up to90m/m. Slip joint design makes adjustment fast & easy.

FT-998B Swivel Jaw Filter Wrench Plier• Jaws swivel 90° in either direction to access most oil and fuel filters.• Works where other oil and fuel filter pliers and wrenches don't.• Jaws adjust to 4 positions, (30° increments) to fit most applications.• Slip-joint handle offers a big range from 3-1/8" to 7-1/2" (80mm to190mm).• Sure grip teeth prevent slipping. • Cushioned handles provide comfort.

CL-012 New Oil Filter Wrench PliersNew design ensures oil filter is gripped on-center to avoid slippage, Safety buttonallows adaptability to pipes of three sizes; Safer and easier to use thanconventional models; Sizes: 9”- 60-90mm; 10”- 85-115mm.

Oil filter service Engine Tools

FT-9286 Oil Filter Key - 3/8"Dr.Applicable for VW-Audi, Seat, Škoda etc. Especially suitable for VW-Audi(Diesel, TDI and 2,4 / 2,6 and 2,8 engine), etc. For Oil Filter with Ø 93mm, 45Ribs

Oil Filter Wrench socketsFT-296 10 points, size: 92mm, depth: 43mmFT-326 8 points, size: 74mm, depth: 35mmFT-306 15 points, size: 105mm, depth: 67mmFT-316 14 points, size: 74mm, depth: 68mm

FT-9282 Oil Filter KeyFor VW-Audi diesel engines with MANN-, Mahle- or Knecht- filter.This tool is especially applicable for removal of oil filters in narrow spaceconditions. Drive: 22 mm hex or 3/8“□, Drive: 22mm hex or 1/2"□ .

FT-9284 Oil Filter Key - 3/8"Dr.Applicable for VW-Audi, Seat, Škoda etc. Especially suitable for VW (e.g. Golf III / Passatup to '96 with TDI-engine) • Audi (e.g. A6 up to '96 with TDI-engine 115 hp); Renault(e.g.Clio; Rapid 1,9 D and Laguna, Safrane; Espace III 2,1 D) • etc For Oil Filter with Ø86mm & 18 Ribs.

FT-9285 Oil Filter Key - 3/8"Dr.Applicable for VW-Audi, Seat, Škoda etc. Especially suitable for Audi (z.B. A4 with TDI-engine) • VW (e.g. Touareg with V 10 TDI engine, Passat’97-onwards with TDI-engine) •Renault (e.g. Laguna; Safrane; Espace III 2,2 D For Oil Filter with Ø 96mm and 18 Ribs.

UG-B01 Oil Filter Wrench, 3 Legs 2 waysFits 3/8” drive; Fully adjustable from 65 ~ 120mm(2-1/2” to 4-3/4”).With 3/8” or 1/2” Square drive with 21mm Navel Hexagon adapter.

UG-B125 Oil Filter Wrench, 3 Legs1/2" Dr. Automotive Special Oil ToolFits 1/2” drive Fully adjustable from 75 ~ 130mm

FT-073 Oil Filter Cap Wrench for DodgeFits Threaded Plastic Oil Filler Caps on Newer Dodge V8 Engines. Helps loosenstubborn oil filler caps by providing leverage. Can be used with 3/8 square drive.Works great in hard-to-reach areas. For use on many Dodge Ram, Dakota andDurango as well as some Jeep Liberty, Grand Cherokee

UG-B01S Oil Filter Wrench, 3 Legs 2 waysFits 3/8” drive, Fully adjustable from 45 ~ 75mmWith 3/8” or 1/2” Square drive with 21mm Navel Hexagon adapter.

UG-B36 Oil Filter Wrench, 3 Legs 2 waysFits 3/8” drive, Fully adjustable from 65mm - 120mm(2-1/2” to 4-3/4”).With 3/8” or 1/2” Square drive with 21mm Navel Hexagon adapter.

FT-9283 Oil Filter KeyApplicable on VW-Audi, BMW, Citroën, Fiat, Ford, Lancia, Mazda, Mercedes, Nissan,Opel/Vauxhall, Peugeot, Porsche, Renault, Suzuki, Toyota, etc. Especially suitable for AudiA3 TDI, VW Golf IV TDI, BMW E36 with 4-cylinder engines, Porsche Cayenne, Boxster,911 and Mercedes CDI engines, as well as C- and E-Class with 4- and 6-cylinder petrolengines. For Oil Filter with 74mm and 14 Flats. Drive: SW 22 mm

CY-156 1/2”Dr. self-griping Oil Filter WrenchFits 1/2” drive; Fully adjustable for Filter 95-165mm

Engine Tools Oil filter service

FT-92812 Oil Filter Wrench 74mm x 14 flutesWrench for gasoil to immersion. Aluminium Filter wrench in 1/2"D for use on AudiBMW,Citroen,Fiat,Ford,Lancia,Mazda,Mercedes,Nissan,Peugeot,Renault,Suzuki,Toyota,Vauxhall/Opel and Volkswagen. 14 sides Ø 74mm

FT-92812A Oil Filter Immersion WrenchWrench for gasoil to immersion; VW CARS15 sides Ø 74mm

FT-92813 Oil Filter WrenchMULTIJET 1.9; 16 sides Ø 75mm

FT-92814 Oil Filter WrenchVOLVO& Mercedes Benz, etc.16 sides Ø 87mm

FT-92816 Oil Filter WrenchFord Mitsubishi Mazda, etc.14 sides Ø 67mm

FT-9287 Oil Filter KeyApplicable for VW-Audi, Mercedes, Seat, Škoda etc. Especially suitable for Mercedeswith 6-cylinder petrol engine M102 and M103. Due to the particularly compact oilfilter wrench design, the oil filter on Mercedes M102 and M103 . For Oil Filter withØ 76mm and 12 Ribs. 3/8" Dr.

FT-9288A Oil Filter KeyAllows quick and easy removal of stubborn Oil Filters. Ø 66 mm • 6 Ribs Renault(Twingo, Clio with D-Petrol engines and filter; 3/8“ Dr.

FT-9288B Oil Filter KeyAllows quick and easy removal of stubborn Oil Filters. Ø 108 mm • 18 Ribs Renault(Trafic, Master, Safrane with S8U-engines and filter. 3/8“ Dr.

FT-92814A 1/2"DR. Oil Filter WrenchHyundai, Kia3.3L(2007)15 sides Ø 88mm

FT-92815 3/8"DR. Oil Filter WrenchTOYOTA(2007). NISSAN and SUZUKI small cars.14 sides Ø 64mm

FT-92810 Oil Filter Key 135 mm 18 flatsNecessary to remove and replace the oil-filter housing when replacing the oil-filterelement. Applicable e.g. for the MAN 18 - 48 tons series F2000, FE and TGA.(MANN Filter No. HU 1381 x) 3/8"Dr.

FT-92811 Oil Filter Key 106 mm hex. 15 flatsStubborn and hard to reach oil filters quickly and easily removed and replaced.Applicable e.g. for the MAN 8 - 10 tons series L2000, LE, M2000 and ME. (MANNFilter No. W 1160); 3/8" Dr.

Oil Filter tool Engine Tools Head Valve Tool

CJ-710 Piston Ring InstallerSave by reducing ring breakage. Tapered jaws to remove and install most passengercar and light truck rings from 3/64" to 1/4" (1.2 - 6.3mm)

FT-516A Valve Stem Seal Remover* Application: PSA HDI engine. * Slide-hammer puller.* Removes seals without scoring or damaging bore in cylinder-head.* Min. hole 21 mm. Height 70 mm. * Length 310 mm. Ø 60 mm.

CJ-760 "Air Holds" for Overhead ValvesHere is a long needed tool to make Overhead Valve repairs without removing the cylinderhead. Set of 14mm and 18mm with 1/4" pipe thread for any quick coupler. It lets air do thework.

FT-9289 Oil Filter WrenchAllows quick and easy removal of stubborn Oil Filters. Ø 76 mm • 12 Ribs • with gripFord with 1,8 diesel-engines and motorcraft-filter EFL 344• Peugeot with Purflux-filter • Renault (R5, Twingo, Rapid with C-Petrol engines; Clio, Kangoo with E-Petrol engines; R19, Espace III, Laguna with F-Petrol engines; Megane, Kangoo withK-Petrol engines and filter; R21, Espace I + II with F-Petrol engine; Trafic with J-Petrol engine & filter

AT-585N Valve Adjusting Tool (Nissan)(for Nissan overhead camshaft engines using spacer shims).Same shim pliers as the AT-585above. except its wedge tool is designed for Nissan GM engines found on Sentra.

2130 Heavy-Duty Hydraulic Valve Lifter RemoverRemove most stuck hydraulic valve tappets with this slide hammer-type tool. Spreadjaws to clamp recessed area of tappet and use slide hammer to remove.

2150 2 pcs Valve Lappers kit2150A 1-1/8" x 1-3/8" diameter cups for large valves.2150B 5/8" x 13/16" diameter cups for small valves.

7900 2 pcs Valve Grinder kit*7900A Suction pads Ø 19 and 22 mm. Length: 245mm*7900B Suction pads Ø 22 and 32 mm. Length: 255mm

FT-92817 Oil Filter WrenchTOYOTA: 2007-2008 3.5L V6, ES 350(2007), GS 350(2007), GS 450H (2007), LS460(2007), RX 350(2007, LS 600H(2008); Lexus GS 300(2006), IS 250(2006), IS350(2006), sides Ø 64.5mm/14PT

FT-958 Oil Filter Remover WrenchSpecially designed for removing the oile filteron GM vehicles with 3 litre Dti engines.

CY-164 Air Operated Valve Lapper Set•Design for operating in tough environments.•Adjustable speed regulator for precise control during operation.•Complete with rubber caps of 20mm, 30mm, 35mm and 45mm

AT-585T Valve Adjusting Tool (Toyota)(for Toyota and other overhead camshaft engines using spacer shims). Shim pliers pushbetween the shim and camshaft allowing the included wedge tool the to be placed between thevalve lifter ledge and camshaft for easy shim replacement.

Engine Tools Head & Valve tool

FT-468 Piston Detaching Tool* For motorcycle vehicle* Description: 16.5 mm to 40 mm capacity * Length: 193 mm

RD-5172 Piston Ring Groove CleanerTwo-easy-to-set cutters included. Sharp steel cutter removes carbon & tarnishes.Fits 2" to 5" (51-127mm) pistons. Three six-bladed cutters cover all major pistonring grooves SEA & Metric. SAE: 1/16" 5/64" 3/32" 1/8" 5/32" 3/16". ; Metric:2.0, 2.5, 3.0, 4.0, 4.5mm, 1/4".; Metric: 1.2, 1.5, 1.8, 2.8, 5.0, 5.5mm.

FT-366 Valve Depressors for Disc Removal* For shimming overhead-camshaft engines. 180mm FIAT Tipo 1.4 DGT.230mm AUDI 80/100, Volks; Golf/Jetta/Sirocco/Passat, VOLVO 740 D.245mm FORD Escort 1.8D - TD/Sierra Tbo D-Dx.

CY-120 Valve Spring Compressor* 8-cylinder Chevrolet or Pontiac, * Heavy-duty tool for fast, easy valve springcompressing; * 12-1/2" (317.5mm) long.

FT-916 / FT-926 Valve Retainer Ring Pliers* For removing valve stem seals on multi-valve-engines.* Working area dip-insulated avoiding damages of the timing gear. * Jaws hardened, longitudinallytoothed. FT-916 Straight design. Length: 250 mm FT-926 Bent 25 degree. Length: 241 mm

FT-936 Valve Seal Removal PliersFor Valve Stem Sealing Rings, The special long, slim form allows quick, easyand safe removal of valve-stem oil-seals, even on 4-valve cylinder heads.

FT-356 Valve Disc Removing ToolLength: 275 mm

CY-8275 H/D Overhead Valve Spring Compressor* Removes valve springs on most cars with overhead valves without removingcylinder head. * Offset jaws grip springs in parallel compression position. * Canbe used on high performance engines.

CJ-710A Piston Ring Pliers - 210mm(L)With prism gripper for safe piston ring spreading.Special steel. Hardened prism gripper. Gunmetal finished tips.

CJ-710B Piston Ring Installer - 245mm(L)Save by reducing ring breakage. Tapered jaws to remove and install mostpassenger car and light truck rings from 3-1/4" to 5-5/16" (83 - 135 mm)

FT-566 Valve Spring Compressor with Straight & OffsetJawsJaw opening : 45~225mm, also available Jaw opening : 75~225mm

FT-566E Valve Spring Compressor for Overhead and L-HeadCompresses valve springs on overhead valve and L-head engines on cars, trucksand tractors. Throat depth 9-3/4" and jaw opening 2-3/4" to 7-3/4" fits largerengine sizes. Jaws and plunger bar are easily adjusted. Plunger bar seats on bothflat and cup shaped valve heads. Includes offset and straight jaws.

Head & Valve Tools Engine Tools

FT-507 Valve Stem Oil Seal Service KitThis kit is essential for renewing the Valve Stem Seals without removing thecylinder head on Audi vehicles with 20v engines. Comprising compressor unitassembly with Valve Spring Holding Tool, Pressure Hose and Valve StemSeal Replacer.

OT-248 Ford valve Spring Compressor ToolYou don't have to remove the head from the engine, it is easier & quicker for valve spring,valve seal, camshaft & retainer service. You can use a 3/8" Drive ratchet or breaker bar towork on 1991 & newer Ford 4.6 Liter. 2 valves. V-8 engines also 1997 & newer Explorerswith 4.0 Liter engines.

OT-919 Valve Spring CompressorAn "on the car" Tool. * Makes compressing the spring and removing the keepers a simplejob because there is no need to remove the head. Adjustable cam action. Fast, because thereis no need to readjust the tool after each spring.

FT-297 Valve Stem Seal Tool SetFor Valve Stem Sealing Rings. This tool set allows the removal and replacementof valve shaft sealing rings.Consists of: * Basic Slide Hammer * Oil Seal Removal Pliers - Long* Valve Seal Collet Chuck (bucket-tappets dia. 26mm upwards)* Valve Seal Collet Chuck (bucket-tappets dia. 23mm upto 26 mm)* Press Set for valve seals (10 pcs., Ø 9.5 - 14 mm inside)

RD-5186 Valve Adjustment ToolsEach tool includes an idle adjustment screwdriver within a socket with window anda different handle for holding adjustment screw in place. For all cars with 10mm;12mm; 9/16" jam nut valve screws. Primarily for “VW” and “Porsche” cars with13mm jam nut valve screws.

CY-246 Valve Seal Removal & Installer KitWorks on both valves still seated or removed.Precision machined seal driving adapters guide the seal for proper setting.1 pcs valve stem seal plier. (Long: 245mm); 1pcs drive handle 6" (150mm) long.2 ocs deep seal driving sockets for seals O.D. 10.8-14.8mm.7 pcs seal driving adapters fit seals 5, 5.5, 6, 6.6, 7, 8, & 3/8".

CY-246C Valve Seal Removal & Installer KitWorks on both valves still seated or removed. Precision machined seal drivingadapters guide the seal for proper setting.1 pcs valve stem seal plier. (Long: 270mm); 1pcs drive handle 6" (150mm) long.2 ocs deep seal driving sockets for seals O.D. 10.8-14.8mm.7 pcs seal driving adapters fit seals 5, 5.5, 6, 6.6, 7, 8, & 3/8".

CY-296 Universal Valve Repair Kit• Completes service tool kit for OHV & OHC petrol or diesel engines onAudi, Nissan, Toyota, Chrysler, Honda, Mazda, Mitsubishi, Porsche, Volvo,VW.

Valve spring compressor Engine Tools Head & Valve Service

FT-163 Valve Shim Pliers.For valve shim replacement; .Application on VW 1.3 l bucket tappet engines.Tips hardened and tempered

FT-506 Valve Stem Seal PliersPEUGEOT, CITROEN and other engines.

FT-837 Valve Shim Remover --- Valve / Opel│VolvoFor use on some European Cars with overhead camshafts which use spacer shims.

FT-183 Valve Spring Tensioner.For pressing down valve springs, when changing the valve stem seals on VW-Audibucket tappet engines 1.3-1.8 l with stud bolts M 8; Replaceable plastic thrust pcs

CY-266 Valve Spring Compressor* Reversible jaw adaptor for multi-valve engines.* Capacity 45-145mm, throated clearance 250mm big window jaw adaptor for easyreplacement of valve collects. * Dual size in 25mm and 30mm diameter.

CY-266A Universal Valve Spring Compressor* Suitable for use on multi-valve petrol & diesel engines with deep seated valves.* Also for use with OHC OHV & CHV engines.* Reversible jaw with 55mm-175mm capacity. * 165mm throat depth.

HL-5014 Valve Spring Compressorfor R & R of valve spring or rocker arm (cylinder head does not need to be removed). Applicable:V-8 engines (M116&117) 4 & 6 cylinder engines with singlecamshaft, With the exception of engines M 102, 103 & 119.

FT-4682 Piston Detaching Tool* For motorcycle vehicle

FT-4681 Heavy Duty Piston Detaching Tool* For motorcycle vehicle * Length: 217 mm* Description: 16.5 mm to 40 mm capacity

CY-263 Valve Spring CompressorUsed for Car & Motorcycle. Pusher size: 16, 19, 23, 25, 30mm; 5pcs pusher forfitting the valve spring correctly and easier to compress the valve spring.

CY-266B Overhead Valve Spring Compressor• For use on a wide range of OHV, OHC and CHV engines. • Not suitable for useon engines with deep seated valves. • Allow valve springs and valve stem oil sealsto be replaced with the cylinder head. • Feature a reversible jaw/adaptor andautomatic cam-action locking to a re-determined setting.

Valve Service Engine Tools

FT-499A Valve Spring CompressorFor Mercedes engines M102 and M103 with single camshaft to change the valve sealwithout removing the cylinder head. The tool does not apply to model 190 E 2.3-16

SF-9035 Truck Valve Remover / Installer set‧ To remove and install the valve of truck. Application range: FUSO 3.5 tons,FUSO over 15 tons, HINO, 750,ISUZU 180, ISUZU 200

FT-499B Valve Spring CompressorFitted with a fork head for 8 mm Cylinder Head Studs. Applicable for removal andinstallation of valve springs on VW-Audi engines from 1.3 l, up to 1993. Pressurepiece , metallastic design. Accessory: Fork Head for Cylinder-Head with 7 mmstuds (e.g. VW Polo, Golf II, Golf III with 1.4 l and 1.6 l engines).

CL-337 Piston Ring Service Tool setPiston ring compressor w/ratchet key:H: 3" (53~125mm); H: 3-1/2" (90~175mm); H: 4" (90~175mm).* piston ring tool capacity: 50~100mm.* piston ring groove cleaning fits: 2"~5" (51 to127mm).* blades x 3 (Sizes: 1/16"~3/16"; 2~4.5mm; 1.2~5.5mm)* Screwdriver : flat & Philipe.

FT-467 Universal Valve-Spring Compressor ToolInstallation example VW-Audi, Ford, Peugeot, Volvo, etc.Applicable for 1-12 cylinder engines - two up to four-valve technology, in-line-engines or V-engines. This tool permits renewal of valve-stem oil-seals with thecylinder head removed or cylinder head assembled. The retaining flanges arerotatable, so that they may be affixed to the cylinder head lengthways, sideways ordiagonally. The correct height of the supporting rod may be adjusted due to theadjustment spindles on the left and right side, to achieve the correct angle betweenhandle and the pressure piece for compressing the valve-spring. Moveable rests allowinfinitely adjustment of the tool length and therefore an universal application for 1-12 cylinder engines.

FT-278AB Valve Keeper Remover & Installer KitFor use on all motors with overhead valves-autos, motorcycles, marine, and aircraft.Will not bend or loosen valve springs. Works on gas or diesel engines; removes andreplaces VW Rabbit keepers. Magnet retains keepers. Takes the place of C-clampstyle removers. Fits most Overhead Valve applications; * Smaller size fits newChrysler New World Engine and some Toyota four cylinders;

CL-324 Piston Ring Toolfor remove and mounting the piston ring,Sizes available : capacity: 50~100mm; 80~120mm, 110~160mm.

CL-327 Valve Spring CompressorCompressor easily removes valve spring on m ost cars and light trucks. Works withcylinder head on or off the engine.

CL-336 Valve spring CompressorRemove and install valve springs with the heads on or off the engine, * Fits 3/8" and7/16" rocker studs, * Handles 1"~2" diameter springs. * press down to compresscoil spring, then remove valve keepers and release slowly.

Valve & piston ring Engine Tools Clutch service

RD-3209 Clutch Adjusting WrenchFor spacer-built heavy-duty clutches. This easy-to-use clutch adjusting wrenchwill solve the difficult, time-consuming job of internal adjustment of spacerangle-spring and multiple lever clutches found on nearly 50% of all heavy-dutytrucks. Until now, a pry bar or other makeshift method was used and oftenresulted in damage to parts, poor job performance, and excessive downtime.

AT-15 Metric Clutch Alignment ToolFor faster, easier replacement or repair of metric clutches. Tool consists of theshaft, ten pilot bushing and two plate alignment cones with graduated turneddiameters for automatic fit of most metric clutch plates. A tapered cone to fit allother is provided.; Sizes: 11.85, 13.85, 15.8, 16.7, 18.98mm.

FT-388 Self Adjusting Clutch Assemble ToolApplicable for the most SAC-Clutche.g. VW-Audi, BMW, Mercedes, Volvo, Opel/Vauxhall, Renault etc.Material available in Alluminum & Steel

HC-7045 Clutch Spring Check Tool

CY-261C 17pc Clutch Aligning Tool setChemically blackened steel components in presentation box. Aids alignment ofclutch plate for assembly. Applications: Audi, Citroen, Fiat, Ford, Honda,Mazda, Mitsubishi, Nissan, Opel, Peugeot, Renault, Rover, Saab, Toyota,Vauxhall, VW, Volvo.

CY-261 Clutch Aligning SetUse to align single disc clutches on most domestic and imported vehicles.Includes shaft and 8 two-stepped pilot bearing adapters for 16 sizes. Platealigning cone has 1-1/8" maximum diameter taper.

CJ-460 S.A.E. Clutch Alignment ToolFaster, easier replacement of clutches. Align clutch plates and pilot bearingsaccurately. Shaft and bushings provide an accurate fit for eight pilot bearingsizes. Two turned sizes (1" and 1-1/8") fit 90% of the clutch plates andcone handles the rest. Metric Clutch Alignment Tool also available

2120 Clutch Alignment ToolFaster, easier replacement of clutches. Align clutch plates and pilot bearing accurately.Shaft and bushings provide an accurate fit for eight pilot bearing sizes. Two turned size(1" and 1-1/8") fit 90% of the clutch plates and cone handles the rest. Shaft and bushingsto fit 8 pilot bearing sizes: 0.587", 0.650", 0.673", 0.748", 0.787", 0.807", 0.981".

SF-8029 Auto Transmission Clutch Spring Compressor -4PinAdjustable legs fit most cars & trucks for replacement of transmission rear clutchpiston snap ring. ‧Special design to assemble &reassemble the clutch snap ringeasier. ‧Capacity : clutch diameter from 64mm to 175 mm.SF-8035 Auto Transmission Clutch Spring Compressor -2PinFor removing and installing the transmission rear clutch piston snap ring.‧Special design to assemble &reassemble the clutch snap ring easier.‧General Transmission Repair Tool. Application range: Adjustable for mostmodels of American cars and light trucks.

Clutch Service Engine Tools

CJ-890 Truck Clutch Alignment ToolsThese truck clutch tools are available in the three most popular sizes: 1-1/2", 1-3/4", and2" O.D. 10-spline shafts. Each tool is constructed of a lightweight fiberglass-reinforcednylon body that won't hang up in the clutch disc spines. Each tool is designed to provide aperfect fit to the spine of the clutch disc. Easily supports heavy pressure plates.Size Available : 1-1/2" O.D. 30mm pilot. Wt.10 oz.; 1-1/2" O.D. 1" pilot. Wt.10 oz. 1-3/4" O.D. 1-1/4" pilot. Wt.11 oz.; 2" O.D. 1-1/4" pilot. Wt.13 oz. 1-3/4" O.D. 1" pilot. Wt.7 oz.

FT-857 Automatic Clutch Spring CompressorA simple snap-in and compression procedure permits removal and installation ofthe snap rings right in the bell housing. The center shaft in the clutch drumassembly no longer must be pressed out to remove the snap ring and piston.

FT-957 BMW Self Adjusting Clutch Fixture/Centering ToolUse to install and set all self adjusting clutches (SAC).Use to reset and center the centering ring on self adjusting clutch.•Applicable: BMW E34, E36, E38, E39, E46, E52, E53, E85, Z3.

FT-509 Cylinder liner puller with support braceWet heavy-vehicle (e.g. Daimler Benz, MAN) cylinder liners, automobile andstationary-engine liners, and other parts may be extracted using this puller.Operation: The spindle of the support brace is screwed into the clamping nut ofthe puller, and the puller inserted into the liner. The support brace is placed on tothe cylinder block. Due to the newlydeveloped spreading system, when thespindle is turned, all three jaws spread quickly and without difficulty, until theyare firmly seated beneath the edge of the liner. Then the nut of the support braceis tightened. Suitable for Cylinder liners with Ø 60 - 160 mm

FT-388C Universal Clutch Alignment Set‧Clutch Alignment and assembly. ‧The vehicles equipped with late-modelfront wheel drives without pilot bear in flywheel.‧Size: Small cone:Range 14.4~21 mm. Large cone:Range 20.9~29 mm.

FT-388F Complete Kit For Assembling And Disassembly OfSelf Adjusting Clutches (3 and 4 hole pitch)Suitable for most Self Adjusting Clutches SAC(3 and 4 holes) equipped onvehicles of FIAT GROUP, VW-AUDI, BMW, MERCEDES, VOLVO, OPEL,RENAULT etc. Allows operations on clutch equipped with this device in order toprevent any damage to system and to keep adapter ring in right position.Advantages: ‧Pre-tightening of disk pushing plate during assembly anddisassembly avoiding clutch deformation.‧Alignment of clutch disk to drive bearing or to disk pushing plate.‧Material:Steel.

FT-388A SAC Clutch Tool SetAs FT-388, but applicable for SAC-clutches (3 and 4 hole pitch)e.g. VW-Audi, BMW, Mercedes, Volvo, Opel/Vauxhall, Renault etc.Consists of : * Clutch pretensioner; * Clutch Aligner* Resetting Tool; * Clutch Mandrel Set* Supplementary set (4 hole pitch)

Engine Tools Clutch Service

FT-388D Clutch Aligner SetFor Clutch-Hub-Ø: 15 - 28 mm. As a result of parallel expansion technique it is possibleto align the clutch plate to the pilot bearing in the crankshaft flywheel. Clutchassemblies no longer equipped with a pilot bearing in the crankshaft can be aligned withthe cover plate using the new parallel expansion technique. Advantage: The expandingsegments expand in the same axis of both the tool body and the crankshaft, so thatalignment of the clutch plate is possible relative to either flywheel or cover plate.

OT-223 Rear Clutch Spring Compressor* Releases rear retainer inside the case makes snap ring easy to remove/replace; * Putsretainer MA Straight w/o bending* For turbo - hydramatic 250 / 350 / 350C Transmissions

HL-9018 BENZ 722.6 Clutch Spring Cmopressor* "BENZ 208 589 00 21 00 R T" (original number) * This tool is to setup a correctgape in transmission clutch. * Set the clutch on press table then place this tool on it andpress the spring cylinder with press to the set-line on the cylider for a correct gape.Application : BENZ 722.6 transmission clutch.

RD-3207 Clutch Release ToolPermits removal of the shipping blocks from new clutch assemblies.A simple one-step operation.

AT-375 Hydraulic Clutch Line Disconnect Tool* For removing hydraulic clutch lines from clutch slave cylinders on some manualtransmissions. Applications: * 1989 to current Mercury Cougars & Thunderbirds.

AT-375A Hydraulic Clutch Line Disconnect Tool* For removing hydraulic clutch lines from clutch slave cylinders on some manualtransmissions.

CY-008 8pc Camshaft Locking Tool KitFor Vauxhalls/Opel cars. This tool aids the removal and replacement of cam followers andcamshafts. Remove the rocker cover and locate the warn cam follower. Rotate the engine tocompress the valve, now set the height of the tool to sit on the valve clamp to the camshafthousing using the rocker cover bolt in the nearest rocker cover bolt hole. Rotate the engine againso the lobe of the camshaft faces upwards leaving the valve compressed. The Cam follower cannow be removed with a bit of deft finger work, also the hydraulic tappet or impact pad can beremoved and replaced if need. Replace the worn cam follower and rotate the engine again andremove the tool.

CY-181 Camshaft Drive Belt Pulley Puller• Special puller designed for pulling camshaft pulley wheels.• Applicable: 4 & 6 cylinder, V6 & V8 engines on VW and AUDI petrol engine.

AT-785 Camshaft lock Set w/adjustable 38mm wrenchcontains: * Camshaft Spanner;* Camshaft Locking Tool RH; * Camshaft Locking Tool LH

AT-395 Self-Adjust Clutch Rotating ToolReplaces self-adjuster mechanism on spacer self-adjust clutches. Permits use of openend or box wrench to make proper clutch adjustment.

CY-0015 Petrol Engine Twin Camshaft setting/locking Kit VW GROUP-1.4/1.6 FSI ENGINES

Camshaft service Engine Tools

2010 Universal Camshaft Bearing ToolDrives camshaft bearing smoothly , now, one complete low cost set that will removeor insert camshaft bearings in nearly all engines from compact cars to heavy trucks.Range of 1.125" to 2.69" (28.58~68.3mm).

OT-291 Universal Cam Securing Bar SetDesigned to Securing cam Sprocket from rotating during the Cam nut on engines.Includes three pairs of different size lock Pins. Lock pins slide in a milled slot whichare secured in place with a bolt from behind. Allows for applicability to a wide rangeof sprocket sizes.

CY-0038 BMW (M42, M50) Camshaft alignment tool* Includes:2 blocks swivel lock plate & locking pin for setting camshaft timing.* Application:BMW engine model M42 & M50

CY-292 Camshaft Pulley Remover / Installer Kit‧Designed to hold the camshaft Pulley stationary while loosening and tightening thecenter shaft bolt. ‧Using the centered screw rod to uproot the pulley.‧Locking screw : M8 M10; ‧Fixed distance : 54-120mm

CY-0040 16pc Twin Camshaft Locking & Setting Tool Kit•FOR PETROL ENGINES; •The kit supplied with adequate tools to lock thecamshafts on twin cam (multi-valve) engines in order to stop them rotating out oftimed position when the timing belt is replaced and removed. •It also providesdifferent camshaft locking pins that can cover specific crankshaft and flywheellocking applications. •Suitable for a range of vehicles including: Ford, Honda, LandRover, Rover and Vauxhall / Opel • Allows the service easier and reduce the risk ofincorrect valve timing from taking place.

CY-182 VW, AUDI Camshaft Pulley Remover․Special design for removing the camshaft pulley on diesel engine TD, TDI etc.....․Applicable: VW, AUDI, SKODA, SEAT.

CY-0038A BMW (M60, M62) Camshaft alignment tool2 blocks swivel lock plate & locking pin for setting camshaft timing.* Application:BMW engine models M60 & M62

HC-7004 Universal Rotating Camshaft Pulleys HolderLength: 360mm; Pin : 5mm & 9mm

HC-2113 Universal Camshaft Pulley Holding ToolIt is the essential disengaging tools for preventing the Flywheel clutch and the pulleyfrom rotating, size: 3/8" drive 5- 6- 8- 10mm- 10mm(longer)

RD-5193A Camshaft Pulley Repair ToolTo hold and manipulate the cam drive pulley on Ford Zeta and Zetec engines. Thistool fits into camshaft spoke enabling it to move accurately for tension, alignmentand sprocket bolt tightening.

CY-294 TOYOTA Cam Tool / Wrench / SpannerUniversal design fits many different types of pulleys having slots or holes, includingcamshaft pulleys and crankshaft pulleys. Wrench is adjustable from 1-1/4" to 5",works with 1/2" ratchet or breaker bar.

Engine Tools CamShaft Service

CY-0038B BMW Camshaft Alignment Tool KitBMW engine models M42 & M50: Includes 2 block swivel lock plate & locking pinfor setting camshaft timing. Engine models M40 & M70: Include plate & lockingpin for setting camshaft timing. BMW engine models M60 & M62: Includes 2 blockswivel lock plate & locking pin for setting camshaft timing.

FT-069 Camshaft Clamp Tool KitFor locking camshafts when checking and adjusting timing. For removing andinstalling camshaft drive gear and eliminating play in gear train.Application:Transporter T5, Touareg.

FT-0693 Engine Timing Tool Kit Volkswagen 2.5/4.9D/TDIPDVolkswagen Touareg and Trasporter 2.5 TDI PD models with a new timing tool kitdesigned for gear driven engines where the injection timing is controlled by thecamshaft followers. This engine is driven by Timing Gears which are morecommonly fitted to engines without an overhead Camshaft or on diesel engines.Most gears used for driving camshafts and diesel injection pumps have helical-cutteetj but some applicatons have spur gears with straight cut or backlash reductionsystems. The service life of the timing gears depends on: Correct gear backlashCorrect lubricaition Timing gears are not mormally considered part of the generalservice and need checking only if they are dismantled or become noisy.

CY-0036 BMW Camshaft Alignment ToolRemoves lock nuts on thermo-Viscous fans found onFord BMW .....many vehicles. Made from tempered pressed steel with PVC dipped handle.;Applicable: BMW engine models M40, M70.

HL-9084 Camshaft/Crankshaft Alignment Tool kitFor alignment of the cam and crankshafts. Also enables correct installation of thecamshafts with the cam cover.Applicable: VOLVO models 850, 960, S40, S70 and S90

7800 Crankshaft Pulley HolderBreak loose the crank shaft pulley / harmonic balancer bolt. Designed to properlysecure the pulley from rolating during R & R of crank bolt.

7800A Crankshaft Pulley HolderBreak loose the crank shaft pulley / harmonic balancer bolt. Designed to properlysecure the pulley from rolating during R & R of crank bolt.

2400 Crankshaft Drive Belt Pulley PullerSpecial universal puller with 132mm spread for removing crankshaft drive beltpulleys with and without bolt holes on European vehicles.

CY-272 Pulley Spinning Tool‧ Special tool for forged pulley. For turning/spinning off the crankshaft,camshaft..etc. ‧ Weight: 390g, Length: 330mm Application: Japanese Vehicles,Mercedes Benz, BMW, Ford, Opel, Peugeot, Renault, Rover, Volvo, VW, Audi.

FT-0697 Camshaft Clamp Tool KitFor Phaeton 2003, Touareg 2003, Transporter 2004, 10-cyl. diesel engine inPhaeton and Touareg for 5-cyl. diesel engine in Touareg and Transporter.Touareg 2003, Transporter 2004, 5-cyl. Diesel engine.For setting engine to cylinder 1 TDC.

Cranhshaft Service Engine Tools

FT-920 Crankshaft Pulley Holder* Suit for BENZ M111, 112; * Brake loose the crank shaft pulley/harmonic balancerbolt. Designed to properly secure the pulley from rolating during R & R of crank bolt.The 50mm hex head armature slips past the lightest of spaces and slides right into thecenter slot on the pulley.

AT-635 Crankshaft Pulley Holder* Ford removal and installation of crankshaft pulley attaching bolt; * Hexagonal shaped toolmates with hole in crankshaft Pulley; * Shallow 1" overall depth fist tight engine compartmentareas; Hole in center allows access to crankshaft pulley bolt with socket; Prevents crankshaft andengine movement when held with breaker bar; * Fits Honda Prelude 1944-95 and someHonda/Acura V6 engines

AT-635A Crankshaft Pulley Holding Tool*Ford removal and installation of crankshaft pulley attaching bolt*Hexagonal shaped tool mates with hole in crankshaft Pulley

SF-8043 BENZ Rear Crankshaft Radial Sealing Ring Installer‧The crankshaft redial sealing ring has both a lip and a protective lip.‧They can not be damaged when assemble the cover to the crankshaft flange.‧This tool is design to prevent damage when assemble the cover to the crankshaftflange. Application range: Mercedes Benz M272, M271.

FT-035 Crankshaft Rotation AdapterNo more broken balancer bolts. Rotates the crankshaft the proper way, when turning theengine with the balancer already installer. Useful when assembling an engine ordegreeing the cam. Easily attaches to the balancer. Then crankshaft can be rotated witha 1/2" breaker bar or a 1" socket and breaker bar.

OT-340 Crankshaft Damper remover/installer kitThe special 3-jaw puller is used with the insert to remove the crankshaft damper whenever timingbelt, water pump, or front cover service is required. * Services Chrysler-built 2.0L, 2.4L, 2.5L,3.3L and 3.5L engines. 1995-newer 3.3L and 3.5L V-6 used in Chrysler New Yorker andConcorde, Dodge Intrepid , and Eagle Visio; 1995-newer 2.0L, 2.4L 4-cyl., and 2.5LV-6 used inCirrus, Stratus, and Breeze; 1995-newer 2.0L 4-cyl. Used in Neon.

FT-328 Universal Pulley Puller Set* For pulling and installing of belt pulleys at power steering pumps, generators, fanwheels, etc. * 2 cross beams: 140 mm and 230 mm long.* 2 pairs of straight pullers: length 60 mm and 110 mm.* 1 pair of specifically formed pullers: length 60 mm.* All pullers and cross beams can be combined.

FT-465 Crankshaft Pulley Remover* Puller grips crankshaft pulley grooves.* Pulley φ130-156mm.; * Groove pitch 3,56mm

FT-347 Puller for Crankshaft PulleyFor VW-Audi 4 and 5 cylinder engines.To remove the front pulley from the crankshaft.

FT-367 Locking ToolTo lock the vibrator damper (pulley at the crankshaft) when the central bolt has to beloosened (e.g. changing of the timing belt).Application: VW engines (e.g. VW T4 Van with 5-cylinder Diesel)

FT-377 Locking ToolFor counterbearing of the V-belt pulley / vibration damper while removing thecrankshaft-centre bolt.; Application: VW-Audi 5 Cylinder diesel engines up to ’97..(AAT, ABP, AEL).

Engine Tools Harmonic balance

OT-501 Master Harmonic Balancer InstallerCovering almost every car and light truck application, old or new. Installs drivepulleys or harmonic balancers that are pres-fit onto the crankshaft. The heavy-duty7/8" diameter forcing screw has internal threads to fit the threaded adapters. Thirteenadapters, in the right reach length to fit most threaded crankshafts. Contains:

CY-011 Chrysler Harmonic Damper Pulley Remover This tool was developed to aid in the removal of the harmonic damper pulleys foundon the many Chrysler Corporation engines. This pulley is hard to access and removedue to space limitations in and around the engine compartment.

6700A Harmonic Balancer Remover Set* 2 of 3/8" x 16 x 4" * Small pointed tip * 3 of 5/16" x 18 x 2" * Flat tip* 3 of 3/8" x 24 x 2" * Long center bolt * 2 of 10mm x 1.5 x 3" * Yoke

CY-125 Honda/Acura Crankshaft Damper Holding ToolTool allows the technician to hold the crankshaft damper whentightening or loosening the crankshaft bolt.

OT-215B Harmonic Balancer Puller & Holding Tool* Designed to remove and install the harmonic balancer on the most popular Chryslerengines; * Includes OT-215A 3-jaw puller, which removes the harmonic balancerfrom the crankshaft and OT-215D Holding tool, which holds the harmonic balancerwhew tightening or loosening the crankshaft bolt or removing the balancer.

CY-238 Pulley Puller & Installer SetRemove pressed-on alternator and power steering pulleys, Threaded end installs late-model GM alternator and power steering pulleys Puller fits some AMC'sWill not work on 3.3L and 3.5L Chrysler engines

CY-117 Pulley PullerRemoves pressed on 1 or 2 groove pulleys from alternators or power steering pumps.Also easily removes alternator bearings. Adjusted by simple thumbscrew movement.

CY-7846 Harmonic Balancer Puller Set‧Designed for use on harmonic balancers, crankshaft pulleys, steering wheels andgear pulleys ‧Can be used on tapped flywheels of electric or two-cycle motors‧Heavy duty 4-way slotted yoke

6600 Master Harmonic Balancer Puller Replacer SetThis unique puller & replacer design includes eight imperial and metric adaptors, plusan end cap adaptor. Special 1/4" shoulder bolts and a 2" extension piece are includedto suit Holden 3800cc V6 Commodore engines. The pulling plate, fitted with its needlerace thrust bearing removes or replaces the pulley by the position of the thrust nut.

OT-228 Taskmaster Twins Puller SetOne flange type puller for removal of parts with 2 or 3 tapped holes, includingharmonic balancers & timing gears. Another special puller for steering wheels,pulleys & flywheels. Contains three 3/8"- 24 x 3, three 3/8"-24 x 3", three 5/16"-18 xx3-1/2" size cap screws.

6700 Master Bolt Grip SetMaster Bolt Grip Set works on harmonic balancers, steering wheels, crankshaft pullers, andgears. Capable of handling almost every two or three-way bolt pull possible on almost every car,pickup, SUV, and small engine. * Two or three way Yoke * 4 pc Tip Set; * Center Screw forPuller(2) * Metric Bolt Set- 8 mm x 80(3), 8 mm x 65(2), 8 mm x 40(3), 10 mm x 50(3)* SAE Bolt Set- 5/16-18 x 4-1/2”(3), 5/16-24 x 3-1/2”(2), 3/8-16 x 4”(3), 3/8-16 x 2”(3), 3/8-24 x 2”(3), 5/16-18 x 2”(3)

Harmonic Damper Engine Tools

OT-294 Gear and Pulley PullerDesigned to pull timing gears, fan pulleys, harmonic balancers, and other tapped-holeparts. * Two hex head cap screws. * 3/8"-16 UNC x 3" long screw.* Puller block, width: 4-7/8", Spread: 1-1/2"~4-1/4"

FT-508A Damper Pulley Puller HolderWrench Set size: 13, 15, 16, 17, 19 mm

FT-508B Damper Pulley Puller HolderWrench Set size: E10- 12- 14- 16- 18.

OT-232 Flange-Type Puller SetRemoves a wide variety of components having tapped hales, including harmonicbalancers and timing gears. Cap screws can be positioned to handle bolt-circle diametersfrom 1-1/2" to 4-5/8".; Includes 3 each of the following cap screw sizes: 1/4"-28 x 3",3/8"-24 x 1-1/2", 3/8"-16 x 2", 3/8"-16 x 3", 3/8"-16 x 4-1/2", 5/16"-24 x 3", 5/16"-18 x3-1/2", 5/16"-18 x 6". M8 x 1.25 x 45mm, M8 x 1.25 x 65mm, M8 x 1.25 x 65mm, M8x 1.25 x 90mm, M10 x 1.5 x 35mm.

OT-322 Flange type Puller Set* Designed to use on a variety of jobs: steering wheels, crankshaft pulleys, gears andharmonic balancers. * Handling almost every two or three way bolt pull possible onalmost every car, pick-up, SUV and small engine. * Slotted holes in puller flangepermit cap screws to be positioned to handle bolt circles from 1-1/2"~4-1/4".

FT-218 Harmonic Balancer Installation ToolFor small block & big block Chevrolet. This tool makes installing the harmonic balancervery easy: just thread the proper end into crankshaft, and then rotate the nut which pressthe bearing against the balancer which will slide onto the crankshaft smoothly.

FT-337 Puller for Harmonic DamperFor VW 5 cylinder engines with poly-V-belt e.g. T4, LT etc. Removes the harmonicdamper while simultaneously reacting against the crankshaft pulley. The FT-337 Pulleris absolutely necessary if the shoulder of the Pulley has corroded onto the harmonicdamper. Advantages: * No damage to the harmonic damper. * High time-savings.

OT-297A Honda/Acura harmonic Damper Pulley Holding ToolThis unique tool has been developed to aid in the removal/installation of the crank bolton most Honda and Acura engines. Performing with a 1/2” breaker bar of ratchet, thistool holds the harmonic damper pulley from rotating when removing the pulley bolt.There is a hole in the center of the tool to allow the use of a socket and extension toloosen or tighten the pulley bolt

OT-297 Handa/Acura Damper Holding Tool

FT-716 Powerbar Hand Impact WrenchRemove replace Harmonic Balancer Pulleys. Up to 600 ft/lb of torque. applicationsinclude pulleys, flywheels, couplings, flanges, lawn mower base plate, etc.

Engine Tools Flange type puller

6700B Steering Wheel Puller* Removes steering wheels on most domestic or imported vehicles, with or withouttelescoping steering columns. * Also works as a regular 2/3-way puller to removepulleys and small engine flywheels.

CY-126 Steering Wheel Lock Plate RemoverRemoves steering wheel lock plates from most vehicles with tilt and telescopingcolumns. Designed for air bag-equipped vehicles. Includes 9/16" x 18" and M14 x1.5mm adaptors.

6700C Flange-Type Puller Set* Contents: M8 x 1.25 x 90mm x 2, M8 x 1.25 x 45mm x 3, M8 x 1.25 x 65mm x 2,M10 x 1.5 x 35mm x 3, 3/8"-16 x 114mm x 2, 3/8"-16 x 76mm x 3, 3/8"-24 x 38mm x3,5/16"-18 x 89mm x 3, 5/16"-24 x 76mm x 2, 5/16"-18 x 151mmx 2, 1/4"-28 x 63 mm x2.Forcing screw: 3/4"-16 x 116 mmThree each of the following flat washer: 16mm, 18mm, 21mm.

CJ-850C Harmonic Balance InstallerIncludes eight adapters for use on a wide range of engines. Adapters sizes are7/16"-20, 1/2"-20, 9/16"-18, 5/8"-18, 3/4"-16, M12x1.5, M12x1.75, M14x1.5 andM16x2.0.

CJ-850A Miscellaneous -Harmonic Balance InstallerIncludes eight adapters for use on a wide range of engines. Adapters sizes are7/16"-20, 1/2"-20, 9/16"-18, 5/8"-18, 3/4"-16, M12x1.5, M14x1.5 and M16x2.0.

CY-205S Steering Wheel Pulley & Flywheel Puller SetHere's a puller that works in a variety of applications.It pulls steering wheels on most late model cars. It also works as a regular 2/3-waypuller to remove pulleys and small engine flywheels. Cap screws included (pairs):3/8-16 x 3-1/2 in.; 5/16-18 x 3-1/2 in.; 5/16-24 x 3-1/2 in.; M8-1.25 x 90 mm; and5/16-18 x 4 in. (SIR).

6700D Flange-Type Puller Set* Covers almost every car, SUV, and small engine. * Capable of handling almostevery two- or three-way bolt pull possible. * For use on a variety of jobs: harmonicbalancers, steering wheels, crankshaft pulleys, and gears. * Storage tray anddetailed application chart included. * Slotted holes in puller flange permit capscrews to be positioned to handle bolt circles from 1-1/2" to 4-1/4".

CY-205 Flange-Type Puller Combination SetTwo specialty pullers in one box. You get a flange-type puller for removal ofharmonic balancers, timing gears, and other parts with two or three tapped holes.You also get a steering wheel, pulley, and flywheel puller.

FT-286 Differential Filter Spanner WrenchSize: 46 mm x 12 PT; Hex Key: 5 mm; Applicable: VW5+6-GangSchaltgetriebe Allrad (Bora, Golf IV, Sharan, Skoda-Octavia)

FT-546 General Puller SetPuller Set for Steering Wheels, Sprockets, Pulleys and Shafts, etc. Range: Ø32~ Ø90mm. Consists of Puller Disc: Ø-110mm (2+3 Hole mounting) with Spindle.Allen-bolt: M8 x 1.25 x 100 - 3pcs; Allen-bolt: M10 x 1.25 x 100 - 3pcs.Hex bolt: M8 x 1.25 x 80 - 3Pcs. Hex bolt: M10 x 1.5 x 50 - 3Pcs.Hex bolt: 1/4"UNF x 75 - 2Pcs. Hex bolt: 5/16"UNF x 90 - 2Pcs.Hex bolt: 5/16"UNC x 50 - 3Pcs. Hex bolt: 5/16"UNC x 110 - 3Pcs.Hex bolt: 3/8"UNF x 50 - 3Pcs. Hex bolt: 3/8"UNC x 100 - 3Pcs.Washers: 1/4" x 19 2Pcs.; 5/16" x 18 3Pcs.; 3/8" x 20 3Pcs.

Power Steering service Engine Tools

CY-144 Steering Wheel PullersFor use on most Ford power steering pump pulleys. Heat treated alloy steelconstruction. Plated for corrosion resistance. Beveled jaws.

FT-690A Special Steering Wheel Puller SetFor Opel, Ford and many other cars. Included long and short pulling arms.FT-690AL long pulling arm. Length: 135mmFT-690AS short pulling arm. Length: 87mm

CJ-380 Special Steering Wheel PullersFor Opel, Ford and many other cars.

CJ-530AB GM Power steering pump pulley kitRemove and install the power steering pump pulley easily and without damaging thepump shaft or pulley. Kitsd included : Ford Power Steering Pump Pulley Installer,GM Power Steering Pump Pulley Installer

FT-227 Steering Link GripperFor to loosen and to tighten steering links. A broad bearing surface and hardenedcontact elements avoid slipping. At the follow-up, a spring cares for that the grippercan be used like a ratchet.Application: Track-Rods Ø 11~14mm.also available size: Track-Rods Ø 14~23mm. Track-Rods Ø 40~55mm.

CY-230A Steering Wheel Remover/Lock Plate Compressor SetFor steering wheel removal of most automotive & light truck applications.Includes steering wheel puller & related bolts.Includes non-threaded puller legs for late model vehicles with non-threaded hubs.Includes pivot pin removing tool for serving tilt s

CY-233A GM Power steering pump pulley install kitEasily installs power steering pump pulley without damage to pump shaft or pulley. Requiredtool for: 1988 thru current GM Quad 4 engines; 1990-current Chevrolet, Lumina APV,Oldsmobile, Silhouette, and Pontiac Trans, Sport mini vans; 3.1L V6 engines on 1991 -currentChevrolet Lumina sedans, Pontiac Grand Prix, Oldsmobile Cutlass Supreme and Buick Regal.

CY-230 Steering Wheel Remover/Lock Plate Compressor SetRemoving steering wheels of most vehicles, with or without telescoping tilt steeringcolumns is easy with this new set.The steering wheel lock plate compressor is also included, to compress the steeringwheel lock plate to remove or install the snap ring.

2040 Power Steering Pump Pulley Replacerwhen it comes to installing power steering pump pulleys, it will not damage internalcomponents by exerting force through the pump shaft. A roller bearing in the toolallows for easy turning and the tool shape prevents damage to the pump.

2050 Power Steering Pump/Alternator Pulley RemoverThe tool removes pulleys on all Chrysler, Ford GM, and VW vehicles; includingSaginaw, Thompson and the Ford C2 power steering pumps. GM belt driven vacuumpumps on boot gas and diesel cars and press-on water pump pulley on GM V6 engines.The 2050 works on pulleys with hub diameters of 1-1/8". 1-1/4", 1-5/16" and 1-3/8"with split collet design, the jaws grip the pulley flange for damage-free removal.

Engine Tools Power steering service

CJ-530C GM Power steering pump pulley installerThis tool offers easy, damage- free installation of power steering pump pulleys. It works on1988-'95 GM Quad 4 engines; 1990-'94 Chevrolet Lumina APV, Oldsmobile Silhouette, andPontiac Trans Sport vehicles; 1990-'94 3.1L V-6 engines; 1994- newer 3100 GM V-6; 1999-newer 3400 GM V-6. Threads are 3/8-16" to fit pulley shaft threads.

OT-941 Steering Wheel Puller & Lock Plate DepressorIncludes selection of bolts and handle in Box for service GM, Ford, Chrysler andAMC cars. Adaptors are included for servicing lock plates on all GM and AMCvehicles with tilt wheel. Detachable handle helps hold puller when turning force isapplied to pressure screw. Industrial finish.

AT-35 Power Steering Pump Alternator Pulley Remover / InstallerThis 2-in-1 impact tool features a 2-sided flange which fit domestic automobilesincluding GM, Chrysler and Ford, and install Saginaw, Thompson and Ford C-2power pumps with grooved assemblies. Works on alternator pulley the followinggrooved hub dia.:1-1/8"(28mm), 1-1/4" (32mm), 1-5/16" (34mm),1-3/8" (35mm)

FT-715B Screw Pusher SetFor loosening and extraction of firmly sitting clamping screws, which fix the link pins in thewheel bearing housing of four-steering wheel front axles; e.g. of VOLKSWAGEN Passat +Synchro, AUDI A4, A6, A8 including Quattor, SKODA Superb. Length: 90mm x Ø 12mm

CY-230C Steering Pivot Pin RemoverApplications: 1969 and newer GM, Chrysler & Ford cars & trucks with tilt ortelescoping Saginaw type steering columns

CJ-820 GM Steering Wheel Puller LegsGM eliminated the tapped holes in the steering wheel assembly on late model cars andvans, making these puller legs the only way to remove the wheel without damage. They'reused with CJ-270 steering wheel puller to get behind the steering wheel assembly to give astraight, even pull. Works on: Pontiac: 1988-93 Lemans;1977-current Grand Prix, Trans

AT-35A Power Steering Pump Alternator Pulley Remover / Installer kitRemoves and installs Saginaw, Thompson, Bishop Bendix, TRW and Ford C-4power steering pump pulleys with grooved hub assemblies. Features a two-sidedflange which also fits most alternator pulleys with grooved center hubs. Suits HubDiameters: 1-1/8"(28mm), 1-1/4"(32mm), 1-5/16"(33mm), 1-3/8" (35mm)

FT-715A Screw Pusher SetFor loosening and extraction of firmly sitting clamping screws, which fix the link pins in thewheel bearing housing of four-steering wheel front axles; e.g. of VOLKSWAGEN Passat +Synchro, Audi A4, A6, A8 including Quattor, SKODA Superb. Length: 110mm x 16mm(SW)

2070 Ford Lock Pin Remover* Removes tie rod inner socket retaining pin on Ford vehicles with rack and pinionpower steering. * Replacement tips available separately.

FT-665A Steering Arm Puller with yokeFor the removal of steering arm gears, ball bearing etc. Clamping device will presslegs securely behind parts to be withdrawn. Especially for extracting the innerbearing ring at VW-Audi cars. Capacity: 20-70mm , Arm length: 94mm

FT-665B Steering Arm PullerFor the removal of steering arm gears, ball bearing etc.Clamping device will press legs securely behind parts to be withdrawn.

Pulley Extrator Engine Tools Water Pump service

CY-143 Seal PullerHeavy-duty, heat-treated steel. Easily removes grease and oil seals. Red vinyl, non-sliphandle. 2 tips for multiple applications.

CJ-720 Cummins water pump pulley Remover/Installer kitThis heavy-duty tool is designed for use on water pumps found on Cummins L10 and M11engines. Installer includes a rugged thrust bearing that allows for friction-free pulleyinstallation without damaging pump components.

FT-003 41mm Water Pump Wrench for GM 1.6LUse With 3/8” Square Drive and Short Extension to Easily Adjust and Hold the Water PumpWhen Replacing or Adjusting Timing Belt. Stubby tool design allows access to timing beltsprocket without interference from vehicle frame. Works on 1.6L engines in 2004-currentChevrolet Aveo excluding 2009 with variable timing engine and 1999-2002 Daewoo Lanos.Heat treated alloy steel for strength.

CY-180 Water Pump Removal Tool KitMaterial: Cr-Mo with S45C Steel. This set allows the crankshaft rotation on TDC-positionand the crankshaft counterhold,during the loosening of the crankshaft center screw or of thewater pump toothed wheel fastening screw.it is also suitable for removal or extraction of thewater pump toothed wheel and water pump itself.For VW T5,Touareg 2.5 L 5-cylinder TDI engines.

CY-154 Water Pump Holding Tool with 3 pcs Screw‧PEIROL 2.2 16-TIMING; ‧Explanation: retains poistion of coolant pump sprocketduring replacement of pump, maintaining engine timing. ‧Explanation: retains poistion ofcoolant pump sprocket during replacement of pump,maintaining engine timing.‧Models: ASTRS,VECTER,VX220,ZAFIRA,SIGNUM(00-04)

FT-020A 39mm Fork Spring Compressor Kit for Harley-DavidsonDesigned to install fork caps on forks with large amount of spring pre-load. Will work onmost 39mm Harley-Davidson fork applications.Kit included: 39mm Adapter, 39mm socket, Jackscrew;

FT-020B 41mm Fork Spring Compressor Kit for Harley-DavidsonDesigned to install fork caps on forks with large amount of spring pre-load. Will work onmost 41mm Harley-Davidson fork applications.Kit included: 41mm Adapter, 41mm socket, Jackscrew;

FT-020 39/41mm Fork Spring Compressor Kit for Harley-DavidsonDesigned to install fork caps on forks with large amount of spring pre-load. Will work onmost 39mm and 41mm Harley-Davidson fork applications.set included : Jackscrew; Adapter: 39, 41mm; Socket: 39, 41mm.

FT-317A Pulley-Extractor and Reaction ToolUiversal application; Loosen the retaining bolt and extract the Pulley. Suitable for allPulleys with holes with a PCD Ø from 70 mm - 100 mm. Suitable for hole Ø from minimum20 mm.; To lock the Pulley while loosening or tightening the retaining bolt, as well aspreventing the Pulley from rotating during extraction. Any available ½“ ratchet or extensiondrive may be used as the reaction tool.contants: 1 x Pressure-Unit; 1 x Puller Plate; 3 xHook Ø 20 mm; 3 x Hook Ø 26 mm; 3 x Shoulder Nut M10

FT-317B Pulley-Extractor and Reaction Toolwith 2 Hooks Ø- 26 mm and 2 Hexagonal Nuts. Suitable for VW-Audi, Seat, Škoda,Opel/Vauxhall Ford, BMW, Mercedes, Peugeot, Citroën, Renault, Fiat, Japanese vehicles,etc. *1 x Puller Plate *2 x Hook Ø 26 mm *2 x Shoulder Nut M10, * 1 x Pressure-Unit

Injector service Engine Tools Sealing service

FT-669 Water Pump/Timing ToolHolds the timing chain and gear in place while removing and installing the waterpump on GM Ecotec engines. Holding the sprockiet prevents loss of timing ordamage to the engine. Special half-moon design allows easier access to water pumpgear bolts. . Uses access cover bolts to hold the tool in place.

SF-8023 Injectors Pump Extractor Remover Set‧Use “U” sleeve or two jaws hook to fix the injector and then pull out with slidehammer, special two jaws design to fix the injector and pull out with slide hammer‧Application range: VW, AUDI (TDI); (FSI); VW, AUDI, SEAT, SKODA

SF-7029 Rear Seal Repair KitWorks on 1994 - 2003 7.3L diesel engine in Ford 3/4- and 1-ton trucks, A completekit with the tools you need to properly remove and install the rear main oil seal andwear ring on the crank shaft ‧Eliminates makeshift methods of seal removal andinstallation that could damage new seal or cranksha ‧To prevent personal injurywhen using these tools, wear eye protection That meets ANSI Z87.1 and OSHAstandards

FT-029 Puller for Sealing RingFor use on sealing rings with internal diameter 4 - 16 mm, e.g. injector nozzle sealingrings on Mercedes CDI engines. The puller extracts the sealing rings correctly, forexample from between the injector nozzle and the cylinder head.To pull out the sealing ring, screw the taper point of the tool into it, then remove withthe impact-type puller.

SF-8027 Slat To Adjust The Pump Injectors 4 cylinder‧Adjustment gauge for testing the installation position or to adjust the pump/nozzle unitduring assembly. The adjusting device (see picture) allows the use of the adjustment gauge onpump/nozzle units with new and /or old solenoid valve nuts. The gauge sizes are the maximumsettings and can be changed accordingly by using the feeler gauge.Adjustment gauge for pump/nozzle unit size 1 , 4 cylinderApplication Engines: Audi and VW pump/nozzle enginesAttention: The two allen screws of the adjustment unit are not be unfastened.

SF-8015 Seal Extractor Kit‧According to space, and as an opportunity to leverage the whole nation to performthe extraction extracted HANDLE.(fig.1+fig2)‧Extractor for oil seals, oil seals, sealing boots, seals, bearing seals and oil seals.‧Now on its own Remscheid Manufacturing: Guarantee the 2-K components withbulky and ergonomically designed handles triangular issue by combining hard andsoft surface parts, a maximum power transfer. Application range: For extracting oilseals, oil seals, sealing boots, seals, bearing seals and oil seals

CY-175A VW, AUDI Injector Remover (FSI)‧Use “U” sleeve or two jaws hook to fix the injector and then pull out with slidehammer. ‧Applicable: VW, AUDI FSI engine.

CY-175B VW. AUDI Diesel Injector Remover‧Special design to remove the seized injector form VAG TDI engines.‧Always allow to cool down the engine before using the tool.‧Applicable: VW, AUDI TDI engine code :ALH/ AHU / 1Z.

CY-175 VW. AUDI Common Rail Diesel Injector (TDI)VW. AUDI Common Rail Diesel Injector (TDI)

Oxygen sensor socket Engine Tools

AT-805 Open-End Hexagon Socket* for Lambda Probes with 1/2" Female Square Drive* Universal application of the lambda probe e.g. on Ford, BMW, OPEL, VW-AUDI.

CY-209H 5 pcs Oxygen Sensor socket & Vacuum switch socektTapered 12m/m and 18m/m threads designed to start and remove carbon & dirt orstraighten damaged threads in spark plug hole. Use with deep socket, open ends orboxes wrench.

CY-209C 6 pcs Diesel Injection Socket KetDiesel Injector Socket Set for Alfa Romeo, Audi, BMW, Chrysler , Ford, Mercedes,Peugeot, Rover, Seat, Vauxhall and Volvo. Also Ford duratorq engines fitted to fordmondeo and transit also included a new injector socket for chrysler voyager andV/M engines fitted to land rovers. Manufactured from chrome molybdenum inblack finish and Packed in a Blow case. Size: 1/2"Dr. x 21mm x 90mm(L); 1/2"Dr. x28mm x 82mm(L) Size: 1/2"Dr. x 22- 27- 28mm x 78mm(L); 1/2"Dr. x 22mm x110mm(L)

CY-209G 3 pcs Oxygen Sensor socket & Vacuum switch socektHEATED OXYGEN SENSOR SOCKET 1/2" Dr. x 7/8"(22mm) x 50mm long.VACUUM SWITCH SOCKET 3/8" Dr. x 7/8" (22mm)x 30mm long.VACUUM SWITCH SOCKET 3/8"Dr. 7/8"(22mm) x 6PT x 80mm long.

CY-209A 4 pcs Diesel Injection Socket KetA set of window sockets for allowing the diesel injectors to be removed. Suitable foruse on Alfa Romeo, Audi, BMW, Chrysler,Ford, Mercedes, Peugeot, Rover, SeatVauxhall and Volvo Size: 1/2"Dr. x 22- 27- 28mm x 78mm(L); 1/2"Dr. x 22mm x110mm(L)

CY-209B 10 pcs Oxygen Sensor & Injection Socket Setfor Oxygen Sensor & Diesel Injection

CY-165 4 pc Toothed Socket Set -Truck Diesel Pressure&Injector1/2" Dr. for mounting, dismounting and tightening the pressure nut at the nozzleholder on commercial vehicles Mercedes-Benz M 401/421, M 402/422, LA, A, M403/423, M 470h, 1/2”Dr. x 72mm(L) x 4 toothes for Mercedes Trucks enginesOM401 / 421,OM403 / 423, LA, A, OM470‧H32 x 70mm(L) x 4 toothes With M14 x 1.5mm receiver thread Mercedes Trucks,Neoplan, Setra ‧H32 x 120mm(L) x 4 toothes for MAN.Mercedes,‧1/2”Dr. x 120mm(L) x 3 toothes Mercedes Trucks, Iveco, Scania, Renault.

CY-209 7 pcs Oxygen Sensor Socket SetFor use on Lambda sensors (oxygen sensors) on most modern cars. This tool covers awide variety of options and fits most heated and non-heated sensors.

FT-317C Reaction ToolApplicable for Mercedes Motor z.B. M112, M113 and OM642, etc.For counter-holding the crankshaft belt pulley when screwingand unscrewing the central crankshaft bolt.

FT-317D Puller Set & Slide HammerSuitable for : VW-Audi, Alfa Romeo, BMW, Citroën, Fiat Ford, Mazda, Mercedes,Opel, Porsche, Renault, Seat, Škoda, etc.

Injector socket Engine Tools Specility socket set

CY-20914 14 pcs Specility Socket Setfor Oxygen Sensor & Vacuum Switch & Spark Plug Hole Thread Chaser

CY-20921 21 pcs Specility Socket SetDiesel Injector Socket Set for Alfa Romeo, Audi, BMW, Chrysler , Ford,Mercedes, Peugeot, Rover, Seat, Vauxhall and Volvo. Also Ford duratorqengines fitted to ford mondeo and transit also included a new injector socket forchrysler voyager and V/M engines fitted to land rovers. Manufactured fromchrome molybdenum in black finish and Packed in a Blow case.

CY-308 Oxygen Sensor WrenchNeeded for servicing computer-controlled vehicle systems. easily removes theoxyen sensor located in the exhaust manifold. Heat treated cast steel.Has 7/8" hex. 1/2" Dr. (double square for easy access). x 50mm long.

CY-313 Opened side Injector Socket - Deep1/2"DR x 22mm x 12PT x 78mm long.Suitable for injectors fitted to GM(Vauxhall/Opel),Mitsubishi,Nissan,VW.

CY-311G Injector Socket1/2"DR x 27mm x 6PT x 78mm long.

CY-312 Injector Socket1/2"DR x 27mm x 12PT x 78mm long.

CY-346 Injector Socket1/2"DR x 22mm x 6PT x 90mm long.

CY-329 Injector Socket1/2"DR x 28mm x 12PT x 78mm long.

CY-347 Injector Socket1/2"DR x 21mm x 12PT x 90mm long.

CY-348 Injector Socket1/2"DR x 28mm x 6PT x 83mm long.

CY-359 22mm Hex. Angled SocketWith radially positioned 1/2"Drive as well as a radially displaced 1/2" Dr.

CY-309 Offset Oxygen Sensor Wrench -22mm* This unique wrench has been developed for use on the LTI GENII 5.71 HOMPFI v-8 found in the 1993 and later Corvette, 1993 Camaro, and 1993Firebird / TransAm; * Additional applications include the 1989 and laterCorvette ZRI with the LTI 5.71 DOHC SFI v-8 as well as many other vehicles; *3/8" sq. dr.

Injector Socket Engine Tools Oxygen Sensor socket

CY-306A 1/2" Dr. Oxygen Sensor Socket1/2” Dr. 7/8” (22m/m) x 90 mm long, 7mm slot for oxygen sensor on Japanesecars Ford, GM, Chrysler & other cars.

CY-306C 3/8" Dr. Oxygen Sensor Socket3/8"DR. 7/8"(22mm)x 6PT x 90mm long. 20mm slot for vacuum.PVS TVS valve & oxygen sensor on Ford, GM, Chrysler & other cars.

CY-306E 1/2" Dr. Oxygen Sensor Socket1/2"DR. 7/8"(22mm) x 6PT x 90mm long. 20mm slot for vacuum.PVS TVS valve & oxygen sensor on Ford, GM, Chrysler & other cars.

CY-309A 3/8" Dr. Vacuum Switch Socket - 22mm3/8" drive 7/8" flare nut socket or vacuum switch & oxgen sensor service oncomputer controlled engines. 3/8" DR. x 7/8" (22mm)x 30mm long.

CY-306 3/8" Dr. Oxygen Sensor Socket - 22mm3/8"DR. 7/8"(22mm) x 6PT x 90mm long. 20mm slot for vacuum. PVS TVSvalve & oxygen sensor on Ford, GM, Chrysler & other cars.

CY-306B 3/8" Dr. Vacuum Switch SocketRemoves vacuum switches on Ford, GM & Chrysler vehicles.Cutaway slot for vacuum hose clearance. Alloy steel construction.

CY-360 1/2" Dr. Vacuum Switch Socket -- 19mm1/2"DR. 19mm x 6PT x 78mm long.7mm slot for oxygen on computer engine controlled cars.

CY-307 3/8" Dr. Vacuum Switch Socket - 22mm3/8"DR. 7/8"(22mm) x 6PT x 80mm long.7mm slot for oxygen on computer engine controlled cars.

CY-305 1/2"Dr. Vacuum Switch Socket - 29mm1/2"DR x 29mm x 6PT x 90mm long, 7mm Slot

SF-9013F MAN & BENZ Truck Diesel Injection Valve Socket‧Remove and install diesel injection valve. ‧Barreled shape. ‧European truckrepair tool. ‧Application range:MAN 422/403 ,BENZ Truck, SCANIA.

SF-9013F Truck Injection Nozzle Socket, 22.2mm‧The tool removes and installs diesel injected nozzle. The bottom four corners.‧Barreled shape, Europe Truck Repair Tool.Application range : Man (422.403), Benz Truck, Scania.

CY-313A 1/2"Dr. Injector Socket - 22mm1/2"DR x 22mm x 12PT x 78mm long.

CY-314 1/2"Dr. Injector Socket - 22mm1/2"DR x 22mm x 6PT x 110mm long.

Engine Tools Oil pressure socket

FT-818A Diesel Injection Pump Remover & Sprocket Retainer - Land Rover/RoverRemoves the diesel pump and retains the pump sprocket in-situ so that thesprockets/timing chain configuration remains undisturbed, minimise the levelof engine disassembly. Essential for transversely fitted engines.

FT-818B Diesel Injection Pump Remover & Sprocket Retainer - BMW M47/M57Removes the diesel pump and retains the pump sprocket in-situ so that thesprockets/timing chain configuration remains undisturbed, minimising thelevel of engine disassembly.

CY-131A Ford Ignition module Tool with T20 Star driverFor removal of 7/32" hex or T-20 Star retaining bolt on Ford ignition modules.Heat treated carbon steel shank. Knurled aluminum knob.

CY-147A Offset Distributor Clamp Wrench - 1/2" & 9/16"Contains two offset box wrenches sizes 1/2" and 9/16".Use tool by itself or turn with 3/8" Dr. ratchet. Drop forged steel construction.

CY-147B Offset Distributor Clamp Wrench - 13mm &15mm13mm Application : 1981 & later Ford V6 (3.8L) engines, 1984-1988 Ford Tempo &Topaz 2.3L HSC vehicles, 1986 & later GM Blazers with V6 (2.8L) engines.15mm Application : GM "X" body cars with V6 (2.8L) engines, 1982 & later Cadillac

CY-321A 3/8"Dr. Oil Sender Unit Socket3/8"DR x 1-3/16" x 6PT x 108mm(L)Long.deep socket services 1987 to current GM's, including 2.0L, 2.5L, 2.8L &3.0L engines. Socket is 5" (108mm) long with 1-3/16" hex

CY-315A 1/2"Dr. Oil Pressure Switch Socket* For late model 2.0L, 2.3L, 2.5L, 2.8L & 3.0L GMS with oil pressure sendingunits.* Use with 1/2" drive wrench; Length- 90 mm

CY-321 Extra Oil Pressure Sending Unit SocketExtra deep socket services 1987 to current GM's, including 2.0L, 2.5L, 2.8L,and 3.0L engines. Socket is 5" (105mm) long with 1-3/16" hex opening. Usewith 7/8" hex wrench or 1/2" sq. dr. tool.

CY-315 3/8"Dr. Oil Sender Unit Socket3/8" DR. x 1" & 1-1/16"(27mm) x 74mm long. Alloy steel, heat treated blackfinished. To remove and install 1-1/16" oil pressure sending units on GM andlate Chrysler. 3/8" Dr.

CY-306G 1/2" Dr. Oxygen Sensor Socket - 22mm1/2"DR. x 22mm x 6PT x 87mm long.

CY-324 Oil Pressure Switch ToolFor quick removal and replacement of oil pressure sending units.Two-step design fits 1" & 1-1/16" oil pressure sending units.3/8" Dr. Round stud or 3/8" Dr. & 3/4" hex on the stud.

CY-351 Oxygen Sensor Socket.Works on all domestic and imported vehicles with oxygen sensors. .Slot insocket's side allows wire clearance . .Outside rib provides added strength, yetdoes not restrict access to sensors. ‧1/2" square drive, 1" male hex drive ontop , 7/8" 6-point opening, 3-7/8" long.

Timing Tool Engine Tools

HL-8010 Diesel Fuel Pump Timing setThis precision measuring instrument is designed for resetting the timing position on Dieselengines with the following fuel pumps : BOSCH EP/VE, ROTORY, KIKKI, NIPPONDENSO, CAV, ROTODIESEL, Top entry these fuel pumps will be found on the followingvehicles with diesel engines : Alfa Romeo, Audi, BMW, Daihatsu, Fiat, Ford, Isuzu, Iveco,Lancia, Land Rover, Mazda, Mitsubishi, Nissan, Renault, Rover and Volkswagen.

CY-0039 Timing Kit for Diesel & Petrol EngineFor use on Audi, Citroën, Peugeot, Volkswagen and Volvo diesel and petrol engined carsand light commercial vehicles. After use, remove all setting pins & locking plates. Turn theengine over twice by hand to complete a full cycle. Regain T.D.C. (top dead center) & insertsetting tools to re-check the alignment is correct. Remove setting tools and check there is noobstruction, by turning the engine over twice by hand again, to complete a full cycle.

HL-8006 Engine Timing Tools kit - Citroen & PeugeotThis comprehensive set of tools B250 enables the correct Engine Timing to bemade when replaceing the Timing Belt. suitable for use on the most recent carswith either HPI (PETROL) or HDI (DIESEL) engines.

CY-278A 6 pcs Timing Tool KitTiming Tools VAG 2.0 TDI PDTiming tool Set for VAG 2.0 Litre TDI PD DOHC engines fitted to Audi A4, A6Skoda; Octavia ll and Volkswagen Golf / Golf Plus / Jetta and Touran models

8400 TDC Timing Degree Wheel360o Timing degree wheel is designed for finding top dead center and checkingcamshaft timing. Three holes allow the wheel to securely fasten to the enginecrankshaft. Use in conjunction with a dial gauge for correct intake and exhaustvalve timing settings. Diameter: 12-5/8" (320mm)

8400A TDC Timing Degree Wheel (Aluminum)360o Timing degree wheel is designed for finding top dead center and checkingcamshaft timing. Three holes allow the wheel to securely fasten to the enginecrankshaft. Use in conjunction with a dial gauge for correct intake and exhaustvalve timing settings. Diameter: 6-4/3" (171mm)

CY-226 Timing Gear PullerRemoves timing gears and other gears with tapped holes. Drop forged yoke isplated to resist corrosion. Heat treated center screw.Includes two 5/16" x 4 bolts.

HL-0032 13 pcs Diesel & Petrol Engine Timing KitFor use on Rover group vehicles. Petrol engine:Metro Gta, Gti 16v DOHC, 111, 114, 214,414, 216 and 416Gti DOHC, 820 8V SOHC.* Diesel engine:218SD, 218SLD Turbo, 418GSD Turbo, Maestro 2.0D, 2.0D Turbo,Maestro 500 & 700 vans, Metro 1.4LD, 1.4SD, Montego 2.0D Turbo and Sherpa DL200.

CY-288 Universal Camshaft Sprocket Puller‧Hold the sprocket and undo the retaining bolt or nut and remove.‧This tool enables the removal of the camshaft sprocket on a wide range of vehicles. ‧Suitable: 45 ~ 70mm

CY-288A Timing Pulley Puller* Draws pulleys by the holes without causing damage. * Moving legs adapt todiffering pulley diameters. * Compact design for use with engine in situ.

Engine Tools Timing Tool

CY-0003 Engine Timing Tools kit - VW & AUDIThis new kit of twelve tools is required for Petrol and Diesel engines serviceincluding Timing belt replacement on recent models and also older 1.9D modelsfrom 1976. Models: AUDI:A4,A6,A8, Allroad (97-04); VW: PASSAT: (98-04)Engines Codes : AFB, AKE, AKN, AYM, BAU, BCZ, BDG, BDH, BFC.

CY-0004 Engine Timing Tools -Citroen &PeugeotThis comprehensive set tools enables the correct engine timing to be made whenreplacing the timing belt. Suitable for use on the most recent cars with eitherHPI(petrol) or HDI(diesel) engines.

OT-856 13 pcs Diesel Engine Setting & Locking kit (Euro)Suitable for Audi, Citroen, Peugeot, Volkswagen and Volvo Vehicles.Manufactured from cropped steel stock. Supplied in carry case.

CY-0006 Engine Timing Tools kit -BMW, VW & AUDIThis set enables the correct Timing position to be made when servicing BMW M472.0 16 Engines. E46 318D 320D 330D E39 520D 525D 530D E38 730D

OT-851 Diesel Engine Injection setting & timing kit* 1600cc & 1800cc diesel injection engines fitted to Ford Fiesta, Escort, Orion,P100, Sierra and Mondeo models * Also suitable for 2500cc DI engines on post1985 Ford Transit Vans

OT-855 13 pcs Diesel Engine Setting & Locking kit (Rover)Cropped steel stock, chemically treated for corrosion resistance. Suitable for Rover groupvehicles. * Petrol: Metro Gta, GTI 16v Twin Cam, 111, 114, 214, 414, 216/416 Gti 16vTwin Cam, 820 8v. Diesel: Metro 1.4LD, 1.4SD, Maestro 2.0D, 2.0D TurboMestro500/700, Montego 2.0DT, 218SD, 218SLD T, 418 SLD T, 418 GSD T, SherpaLD200.

OT-850 FORD Diesel Engine Timing Kit* For use on 1.6 and 1.8 diesel engines fitted to Ford Fiesta, Escort, Orion, P100,Sierra and Mondeo models. Also suitable for 2.5DI (direct injection) Transitmodels (Feb. 1985 onwards).

CY-238 Ford Diesel Engine Injection Timing KitApplications: 1600cc & 1800cc diesel engines fitted to Ford Fiesta, Escort, Orion,P100, Sierra and Mondeo models.Also suitable for 2500cc DI engines on 1985 and later Ford Transit Vans andGalaxy 1900cc TD vehicles.

OT-235A Cam Positioning Tool* For setting the camshaft timing on 1991-newer 4.6L 2-valve, 5.4L V-8, and 6.8LV-10 engines. * Tools install onto the camshaft to prevent it from rotating whencam timing is being adjusted.

OT-238 Chrysler Timing Belt Adjustment Wrench* Makes belt tension adjustment easier and correct* Holds tension on belt, while tightened nut to correct torque eliminates over orunder tightening; * For Chrysler 2.2L and 2.5L engines.

Timing service Engine Tools

CY-0022 Petrol Twin Cam 1.6 16VModels : BRAVA/BRAVO, MAREA/WEEKEND, STILO, MULTIPLA &PALIO, WEEKEND(95-04)Engines : 178B3.000, 182A4.00, 182A6.000 & 182B6.000.

CY-0003C Universal JGO Adjust Core ToolThe adjustable key allows to tighten the free roller in spaces even limited.

CY-0003B Engine Timing Tool KitApplicable: ‧VW-AUDI 2.5 TDI V6 & AUDI A8 3.3 TDI V8 ENGINE.‧AUDI V6 PETROL & V6/V8 DIESEL ENGINE.

CY-0009 Petrol 1.0, 1.2, 1.4 Twin Cams (CHAIN)Models : CORSA, AGILA, ASTRA, MERIVA (97-04)Engines : 1.0 12v, 1.0 16v., 1.4 16v. (chain)Codes : X10XE, Z10XE, Z10XEP, X12XE, Z12XE, Z14XEP.

HL-8013 Diesel 1.7 Opel & IsuzuModels : OPEL engines : ASTRA, CAVALIES,VECTRA-A (87-00), ISUZU, NOVA,CORSA/COMBO, STRA, CAVALIER, VECTRA, FRONTERA, MONTEREY, MIDI,BRAVA (88-04) Engines OPEL : 16DA, 17D, 17DR, X17DTL.ISUZU : 4EC1, 4EE1, 4JB1,4XJ1, 4JA1,4JG2, 4FC1, 4FD1, 4FG1, Z17DT,Y17DT/DTL.

CY-0003D Camshaft Locking ToolApplicable VW : POLO , CLASSIC, GOLF,BORA, BEETLE, CADDY (97-04).Engine : 1.9 SDI/TDI

PC-1656 Twin Cam Adjustable Timing Locking ToolDesign for each type Twin Cam locking tool, Special design for adjusting the pinto lock the cam. Material: Aluminum & plastic.

CY-0011 Camshaft/Crankshaft Alignment Tool SetSpecial made for alignment of the cam and cranshafts.Allows correctly installation of the camshafts with the cam cover.Applicable: For VOLVO models 850, 960, S40, S70 and S90.

CY-0023 Engine Timing Tool Set - Citroen & PeugeotMet de uitbreiding kunt u nu ook aan de 1.4 en 1.6 HDI werken.

HL-8065 Engine Timing Tensioner Kit - for most Petrol & Diesel EngineA comprehensive range of tension lever and wrenches required for changing thecam belt on most popular petrol and diesel engines including: Alfa Romeo,Fiat, Citroen, Peugeot, Renault, Volkswagen.

Engine Tools Timing Tool

CY-0001 Attrezzo Messa in Fase Toolfor Camshalf Regulation;applied for RENAULT ESPACE 2.2; DCI-MASTER 2.2/2.5DCI

CY-0032 Engine Timing Tool Set - Citroen & PeugeotThis comprehensive set tools enables the correct engine timingto be made when replacing the timing belt. Suitable for use onthe most recent cars with either HPI(PETROL) or HDI(DIESEL)engines.

CY-273 Engine Timing Tools set - Ford & MazdaCamshaft setting/Locking Plates are used to accurately align a detumslot, located in the end of Camshaft T, with the top face of the Camshafthousing to hold, the Camshaft at the (TDC) Top Dead Centre position.Locking pins are designed to pass through datum holes in the timingbelt pulleys into fixed position timing holes on the Engine.

CY-0037 12 pcs Engine Timing set -Land RoverNew EDC manual transmission timing pin. * 200 TDI 300 TDI & 2.5 DieselEngine. ‧Combubed crankshaft damper puller and fuel pump gear locking tool

CY-0029 Timing Tools Setfor BMW/ Land Rover / GM 2.5 TD5 EnginesThis timing tool set includes: Crankshaft holding tool; Timing Chain Compressor;Injection Pump Puller; Shaft Puller Timing Pins for 2.5 TD5 engines.

CY-0002 Engine Timing Tools kit - VW & AUDIapplied models : AUDI : A4, A6, A8, A11road(97-04) VW : PASSAT(98-04)Engines code: AFB, AKE, AKN, AYM, BAU, BCZ, BDG, BDH, BFC.

CY-0008 Engine Timing Tools kit - GMThis set of Timing Tools enables the correct Timing position to be made whenservicing GM ECOTEC 2.0 Engines; Applications: VAUXHALL/OPEL, VECTRA2.0D TURBO, SINTRA 2.2D TURBO , ZAFIRA 2.0D TURBO, FRONTERA-B2.2D TURBO,SAAB 9-3 2.2D TURBO,

CY-0016 AUDI Camshaft Alignment toolHolding /Alignment Fixture Align and hold camshaftApplicable: VW polo Disel,Audi 100 since 1991, & I A6 with Z15L TDI engine.

CY-0018 Timing Tool KitTiming tools for Ford 1.8 TDDI/ TDCI from 2000 to 2006 including Fiesta / Focus/Camax/ Tourneo/ Transit with chain driven engines.

CY-0016A AUDI Camshaft Alignment toolHolding /Alignment Fixture Align and hold camshaftApplicable: VW polo Disel,Audi 100 since 1991, & I A6 with Z15L TDI engine.

Timing Tool Engine Tools

HL-8019 Diesel 2.0 & 2.4 TDDI - TDCI (CHAIN)Models : MONDEO & TRANSIT (01-04)Engines : 2.0 & 2.4 DURATORQ 16v.Codes : FMBA/B, D5BA, ABFA, D3FA, F3FA, D2FA, D4FA, F4FA.

HL-8048 Engine Timing Tool set for Fiat & OpelThis Timing Tool Kit is specifically designed for Fiat Chain engine fitted to thevery lates vauxhall/Opel 1.3 and 1.9 CDTI models (2004 onward)

CY-0043 26pcs OPEL VAUXHALL SetA comprehensive 16pcs set of engine timing locking tools for camshaft, crankshaftand flywheel. Covers/ Citroen/ Fiat/ Ford/ Opel/ Peugeot/ Renault/ Rover/Vauxhall/ Volkswagen

CY-0013 Vauxhall/Opel Timing Tool Kit (Diesel 1.9 CDTI)MODELS:ASTRA, ZAFIRA, VECTRA & SIGNUM (04-)

CY-0021 Timing Tool kit for Fiat diesel engine 1.3Applicable: ASSORTMENT for HYUNDI, MAZDA, MITSUBISHIHYUNDAI: SONATA. MAZDA: 626, 323, PREMACY MITSUBISHI:CARISMA, SPACE STAR,SPACE WAGON, GALANT, SIGMA, PAJERO.

CY-0014B Petrol Engine Sstting-Locking Tool‧Models: VW group 1.2 single(6V) and twin camshaft (12V), Skoda, Fabia, VW, POLO. ‧Engines AWY and AZQ.

CY-0014 Petrol Engine Sstting-Locking Tool kitModels: VW group 1.2 single(6V) and twin camshaft (12V)3 cylinder petrol engines(02-) in SEAT, LBIZA/CORDOBA, SKODA,FABIA, VW, POLO. Engines AWY and AZQ.

HL-8047 Timing Tool kitfor Vauxhall/Opel Diesel 1.9/2.2/2.5 DCI (VANS)MODELS:CLIO, MEGANE, SCENIC LAGUNA, ESPACE, KANGOOTRAFIC & MASTER(99-04); ENGINE:1.5、1.9、2.2 & 2.5 DCI; CODES:K9K, G9T,G9U

CY-0010 Engine Timing Tool SetApplied for MODELS:ASTRA VECTRA VX220 ZAFIRA & SIGNUM (00-04);EXPLANATION:Retains position of coolant Pump sprocket during replacementof pump, maintaining engine timing; CODES:K9K、G9T、G9U

CY-00105 Timing Tool For PEIROL 2.2 16V‧PEIROL 2.2 16 - TIMING ‧Models: ASTRS, VECTER, VX220, ZAFIRA,SIGNUM (00-04) ‧Explanation: retains position of coolant pump sprocketduring replacement of pump , maintaining engine timing.

Engine Tools Timing Tool

HL-8020 Diesel 1.5 / 1.9 / 2.2 / 2.5 DCIModels: CLIO, MEGANE, SCENIC, LAGUNA, ESPACE, KANGOO, TRAFIC& MASTER (99-04). Engines: 1.5,1.9,2.2 & 2.5 DCI. Codes: K9K, F9Q, G9T,G9U.

CY-0044 VW, AUDI Engine Timing Tool Set (2.0 FSI)•With camshaft tools, chain tensioner retainer, locking pins and tensionerbolt.•For 2.0 FSI petrol engines since 2003.•Applicable:AUDI A3 2.0 FSI and FSI SOHC engine codes:AWA , BHD,BMB VW GOLF 2.0 FSI and 2.0 FSI SOHC and Touran 2.0 FSI SOHCengine codes: AWA, AXW.

CY-0023 Engine Timing Tools set - Citroen & PeugeotMet de uitbreiding kunt u nu ook aan de 1.4 en 1.6 HDI werken.

CY-0044 Engine Timing Tool Set -Professional Engine-BMW•For BMW diesel engines M41, M51, M47TU, M47TU/T2, M57/ TU / T2:2.01 / 3.01 year 1998-2008 •nstallation and removal of the camshaft /hydraulic chain tensioner •Checking and adjustment of camshaft timing.•Easily accessible operating instructions including cross references to originalpart numbers •Spare parts optionally available.

CY-0031 Engine Timing Tools for VAG 1.8 Turbo & 1.6 FSI CHAIN DRIVEN ENGINESFor AUDI/ VOLKSWAGEN/ SEAT/ SKODA

CY-0033 Camshaft Locking Pin Set‧Dura-torq chain engines in Mondeo 2.0 TD / TDCi (2000-2003)‧Transit 2.4D (2000-2003)

CY-0001B Water Pump Tool SetModels: ASTAR, VECTRA , VX220, ZAFIRA, SIGNUM (00-04)

CY-0045 BMW (M52,M54,M56) Timing Tool Kit* BENZ double vanes setup bracket.* Application : BMW M52, M54, M56.

CY-282A Engine Timing Tool for Renault‧For following engines : K4J, K4M & F4P, F4R TWIN CAM 16V ENGINES.

CY-0045A BMW Double Vanos Setup Bracket M50-TU"11 6 150/151 CE 12/03" (original number)* Application:BMW M52、M54、M56.

CY-0045B BMW Timing Tool* "11 6 150/151 CE 12/03" (original number)

Timing Tool Engine Tools

CY-0024 Engine Timing Tensioner Kitapplied for most Petrol & Diesel Engines, A comprehensive range oftension lever and wrenches required for changing the cam belt on mostpopular petrol and diesel engines. ‧Including: ALFA ROMEO, FIAT,CITROEN, PEUGEOT, RENAULT, VOLKSWAGEN

CY-0007 Timing Tool for Blet/Chain Engine - RenaultPoint to: Clio 1.2/1.4; Megane 2.5D/TD; Clio 1.4/1.6/1.8 16v; Megane1.4/1.6/2.0/ 16v; Clio Sport2.0 16v; R19 1.4 ; Clio Williams 2.0 16v; R191.4 Eco; Espace 2.0; R19 1.8 16v; Espace 2.0 16v; Rapid 1.4; Espace 2.2TD; Safrane 2.0 16v; Express 1.4; Safrane 2.2 TD; Extra 1.4; Safrane 2.520v;ngoo 1.2/1.4; Scenic 1.4/1.6/2.0 16v Laguna 1.6 16v; Trafic 2.5D;Laguna 1.8/2.0; Twingo 1.2; Laguna 1.8/2.0 16v; Laguna 2.2 D/TD;Laguna 2.5 D/TD

CY-0034 Engine Timing Tool setThis Timing tool kit of three special components enables the timing position to beheld on K4J, K4M&F4P, F4R TWIN CAM 16V engines. This New Camchaftpulley setting Tool holds two pulleys in place while changing the Cam belt. thistool is bolted to the center of the cams using the existing bolts.

CY-0012 Engine Timing Tool set - Renault‧This timing tool kit of three specific components enables the timing position tobe held on K4J, K4M & F4P, F4R twin cam 16v engines. ‧This new camshaftpulley setting tool holds two pulleys in place whilst changing the cam belt. Thistool is bolted to the centre of the cams using the existiong bolts.

CY-0026 Engine Timing Tensioner Kit‧This comprehensive set tools enables the correct engine timing to be made whenreplacing the timing belt. ‧Suitable for use on the most recent cars with eitherHPI(petrol) or HDI(diesel) engines. CITROEN: AX, BX, ZX, XM, VISA, SAXO,XSARA, XANTIA; Synergie/Evasion, Berlingo, Jumpy, C15, C25, Picasso, C5;PEUGEOT: 106, 205, 305, 306, 307, 309, 405, 406, 605, 607, Expert, Partner,Boxer

CY-0028 Engine Timing Assortment KitTIMING ASSORTMENT FOR FIAT/IVECO/PAS/FORD

CY-0025 Engine Timing Tool Kit - Professional EngineRepairPetrol Engines: FIAT BRAVA, BRAVO, BARCHETTA, CARGO, COUPE,MAREA, PALIO WEEKEND, PUNTO,MULTIPLA, STILO, IDEA DOBLO,TWIN CAM ENGINES 1.2/1.4/1.6/1.8 16V.Diesel Engines: FIAT BRAVA, BRAVO, MAREA/WEEKEND,PALIO, PUNTO.MULTIPLA, DOBLO, ULYSSE,DUCATO, STILI JTD DIESE ENGINES1.9D/TD 1.9JTD 2.4TD/JTD.

CY-0035 Engine Timing Locking Tool for Alfa RomeoApplicable for Alfa Romeo Twin Spark 1.4 ; 1.6 ; 1.8 ;and 2.0L 16V TwinCampetrol engines (Engine code: 162.01, 322.01, 323.01, 323.10,335.03,671.06.672.04, and 676.01)e,g. Alfa Romeo 145,146,147,155,156,166, Spider andGTV. To prevent the engine shafts (e.g. camshafts, crankshaft ) from turning or tokeep them in a specific position when chaning a timing belt or during other enginerepairs.

Timing Tools Engine Tools Spark Plug service

FT-656S Internal Spark Plug Rethread ToolThe tool uses the better threads at the base of the spark plug port and greatlyreduces the chance of debris from falling into the cylinder. • Cleans and rethreadssparkplug ports from the inside out. • Uses the good threads at the base of the port.• Reduced dirt and metal from being driven into the cylinder head.• Use light grease on the end to trap filings and keep tool easy to use.

HL-9083 2 pcs Spark Plug Socket RemoverThe VW and Audi Steel spark plug boots are designed to seal and increase contactbetween the spark plug and spark plug wire. With the increased seal and locationof the boot , a special tool has been developed to access and remove the spark plugboot. This sparkplug boot tool was designed in hardened stainless steel for longterm service for the professional technician. The "T" handle gives the technicianplenty of pulling power to remove and replace the most difficult spark plug boot.

CY-0030 Engine Timing Tool Kit - VW & AUDI W/4 Grooves & Alu FinishThis new kit of twelve tools is required for petrol and diesel engine serviceincluding timing belt replacement on recent models and also older 1.9D modelsfrom 1976. Models: AUDI: A4,A6,A48,A11 yoad(97-04) VW: PASSAT (98-04)Engines codes: AFB, AKE, AKN, AYM, BAU, BAU, BCZ, BDG, BDH, BFC.

CY-0041 Engine Timing Tool Kit - for Professional Engine Repair BMW N42 / N46 / N46T•For adjustment and arresting of the twin camshaft on petrol engines:- Engine timing: checking and adjustment- VANOS unit: removal, installationand alignmnet •Easily accessible operating instructions including cross referencesto original part numbers. •Spare parts optionally available.•Clear arrangement of tools in high-quality plastic case with soft foam insert.BMW: E87 118i / 120i N46 engine; E46 316i / 316ti / 318ti N42 engineE90/E91 318i / 320i / N46 engine E85 Z4, 2.01 N46 engine

CY-240 4pc Ignition Coil Remover Tool Set‧For Removing and installing ignition coils with power stage of injectionengines on VW 8 and 12 CYL. For Removing and installing ignition coils withpower stage of injection engines on 5 and 6 CYL ,VW GOLF, BORA, 4 & 5CYL. VW PASSAT,6 CYL,VW SHARAN, TOUAREG,PHAETON. ‧Forremoving and installing ignition coils with power stage on VW POLO, GOLF 1.4,1.6i ,CADDY 1.4i,BORA 1.4,1.6i, PASSAT , TOURAN 1.6i , PHAETON,TRANSPORTER T4. Meterial: SCM440

CY-0042 Engine Timing Tool Kit - for Professional Engine Repair BMW N42 / N46•Suitable for the following application: camshaft installation and removal as wellas removal and installation of the inlet camshaft and carrier assembly /Valvetronic System •Easily accessible operating instructions including crossreferences to original part numbers •Spare parts optionally available •Cleararrangement of tools in high-quality plastic case with foam insertBMW: E87 118i / 120i N46 engine; E46 316i / 316ti / 318ti N42 engineE90/E91 318i / 320i / N46 engine; E85 Z4, 2.01 N46 engine

CJ-450 Round "Key Chain" Spark Plug GaugeThis popular solid steel spark plug gauge is designed with a tapered edge for gauging sparkplugs and with a flanged hole to adjust the side wire of plugs without pressuring centerelectrode. Marked in standard and metric sizes. Used to gap all plugs from .020 to .100(0.5 to 2.53mm).

Spark Plug service Engine Tools

CJ-320B Limited Access Spark Plug ChaserFits Spark Plug Holes with Limited Access.The narrow profile and long length allows access to spark plug holes in confinedspaces. Use with a 3/8" ratchet or extension. Size: M14x1.25 .

CJ-300 10mm & 14mm Spark Plug Rethreader TapUse with any standard 13/16" deep socket.

CJ-280 10mm & 12mm Spark Plug Rethreader TapUse with any standard 13/16" deep socket.

CJ-320 14&18mm Spark Plug Thread Cleaning ToolUse with any standard 13/16" deep socket.

CJ-310 Spark Taper -- 14mmFeatures 5/8" hex and 3/8" square drive. Can be used with Extended Spark PlugSocket.

CJ-290 12mm & 14mm Spark Plug Rethreader TapUse with any standard 13/16" deep socket.

CJ-510B Rethreader Kit For 18mm Spark PlugsIncludes the following-also available separately:CJ-510B-1 Tap and Reamer CJ-510B-2 Insert - 7/16" longCJ-510B-3 Insert - 1/2" long CJ-510B-4 Insert - 5/8" longCJ-510B-5 Insert - 13/16" long

CJ-320A Oxygen Sensor Thread ChaserCleans Threads in Oxygen Sensor Holes.Use with 3/4" hex socket or 3/8" square drive. Size: M18x1.5 Also works onM18x1.5 spark plug threads. IMPORTANT: Use anti-seize.

CJ-510 Rethreader Kit For 14mm Spark PlugsIncludes the following-also available separately:CJ-510-1 Tap and Reamer CJ-510-2 Insert - 3/8" longCJ-510-3 Insert - 7/16" long CJ-510-4 Insert - 1/2" longCJ-510-5 Insert - 3/4" longCJ-510A Rethreader Kit For 14mm Spark PlugsIncludes the following-also available separately:CJ-510A-1 Tap and Reamer CJ-510A-2 Insert - 3/8" longCJ-510A-3 Insert - 7/16" long CJ-510A-4 Insert - 1/2" longCJ-510A-5 Insert - 3/4" long

OT-939 Flexible spark plug socket & Ext. barThis spark plug sockets are designed to securely and safely hold both the longerspark plugs being used on newer cars plug the conventional shorter spark plugs.The socket have plenty of clearance at the top and are deeper ate the base to holdthe spark plug hex securely, A special rubber insert insures a snug fit.* OT-939A 3/8"dr. x 13/16" Alloy steel, heat treated 340mmL.* OT-939B 3/8"dr. x 5/8" Alloy steel, heat treated 340mmL.

CJ-510C Rethreader KitIncludes the following-also available separately:CJ-510C-1 Tap and ReamerCJ-510C-2 Insert - 11mm(7/16") longCJ-510C-3 Insert - 16mm(5/8") longCJ-510C-4 Insert - 19mm(3/4") long

Elec-Stethoscope Engine Tools Shock absorber tool

FT-548 Glow-Plug Connector Pliers(straight)To remove stubborn and awkward to reach Glow-Plug connectors, found on thelatest generation of engines. e.g. Mercedes, BMW, VW-Audi etc.

FT-558 Glow-Plug Connector Pliers(angled)To remove stubborn and awkward to reach Glow-Plug connectors, found on thelatest generation of engines. e.g. Mercedes, BMW, VW-Audi etc. *angled 90°

PT-7632 Automotive Noise FinderPortable automotive noise finder which could quickly detect source or locationof noises emanated from bearing, gear, valve, valve body, cranfshaft, cylinder,gearbox, car body and more parts after staring engine; It helps the servicemanto pinpoint the actual noise part and severity even in severe ambient noise Todetermine the trouble location according to different noise Sound amplificationwith volume control Battery voltage indicate

CY-1558 Mechanic's StethoscopeLocates source of engine noise quickly. Listen for trouble by tracingsound of flowing water, oil, gas or steam. Handle is shockproof.

HC-2114 Combination Electronic Stethoscope KitSuper-sensitive stethoscope with rubber cone and test probe. .Suitable fordetection of faults in: Engine, Transmission. .Cat Intake/Exhaust Manifold.Fuel Injectors, Radiators. Valves, Fuel Tanks. .Kit includes audio probe,headphones, Four clip-on microphones and four channel microphone selectorboxes. .Used by Noise, Harshness and Vibration engineers can isolate problemsources. .Enables vehicle to be road-tested and diagnosed simultaneously.

FT-057 Shock Absorber Screwing Pin WrenchFor the operation of the upper shock absorberscrewing on MERCEDES-BENZ,type 211 T-model rear (E-class station wagon)• Operation with 3 front pins, Ø 8 mm • Length: 230 mm

HC-2114A Electronic Stethoscope KitThis model helps locate and evaluate bearing or machine noise for maintenancediagnosis. The analogue output can be fed into an audio tape recorder (notsupplied) for further analysis or for use as a reference for future comparisons.The headphones supplied are based on standard ear defenders, which minimiseinterference from ambient factory noise.

SF-7019 Shock Absorber Piston Rod Tool set‧ Indispensable for locking the shock absorber piston rod whilst loosening ortightening the piston rod nut, e.g. on Macpherson struts.Application range : VW-AUDI, SEAT,FIAT,VAUXHALL/OPEL, PEUGEOTRENAULT, BMW,MERCEDES, JAPANESE PASSENGER CARS,VOLVO,NISSAN, MERCEDES W203

SA-6518 18 pcs Shock Absorber Tool setFor repair work at the spring strut, shock absorbers, removing strut unit. Forretaining the piston when installing and removing strut unit. Ratchet wheel,pawl, shift lever, 2 screws, ball and compression spring 6-point: 16, 17, 18, 19,21, 22, 24mm; T50: 16, 17, 18, 19, 21, 22, 24mmFor repair work at the spring strut, especially for retaining the piston roadwhen installing or removing strut units. 7mm for MERCEDES-BENZ Vaneo;8mm for BMW; 9mm for OPEL Corsa B, Astra F, G, Vectra B 5. 6-7-8mm, 5x 8mm, 6 x 8mm For PORSCHE Cayenne S, VW-Touareg 7.1 x 9.6mm