Residual current devices - Seen Joo

3/1ABB SACE

3Index

F 200, DDA 200, DS201, DS202C and DS 200 System pro M compact RCDs .............. 3/2

DDA 60, 70, 90 for S 290 MCBs, DDA 800 RCD-blocks and DS800 ............................ 3/61

DS 271 electronic RCBOs 1P+N ..................................................................................... 3/80

RD2, RD3, RD residual current relays and TR Toroidal Transformers ........................ 3/84

Residual current devices

trade inquiry contact: [email protected]

2/2 ABB SACE

3

RCDs assure a protection to people and installations against fault current to earth. They are divided into three families:

- RCCBs, which are sensitive only to earth fault current (therefore they have to be connected in series with a MCB or a fuse to protect them against overcurrents and short-circuits)

- RCD-blocks, which are devices to be assembled on a MCB with lower or equal rated current to provide protection against both earth-fault currents and overload or short-circuits

- RCBOs, which combines in a single device protection against both earth-fault currents and overloads or short-circuits.

New RCDs System pro M compact® range presents a wide offer for all the three families, respectively F 200, DDA 200 and DS 200 series.

A large offer for standard instantaneous and selective AC and A types is completed with some confi gurations for special applications, like AP-R type against perturbations or AE type for emergency stop.

All sizes up to 63 A with all the sensitivity thresholds up to 1 A are offered in all the possible pole confi gurations.

The new F200 PV B is specifi cally designed for differential protect against earth-fault currents in photovoltaic installation.

ABB expands the offering of its System pro M compact® with new residual current circuitbreakers with overcurrent protection, DS201 (1 phase + neutral) and DS202C (2 phases) both available in two modules.

The new residual current circuitbreakers with overcurrent protection are a technologically advanced and comprehensive range, as concerns size, tripping characteristics, breaking capacity and accessories.

DS201 and DS202C combine protection against overcurrent

the differential tripping and which cannot be activated in case of manual operation on the toggle.

With the practical label carrier fi tted in the new circuitbreakers you can give maximum visibility to the information relating to the protected loads.

ABB RCDs obtained a lot of marks and approvals and offer the same “plus” advantages of the other System pro M

compact® devices.Residual current relays together with toroidal transformers can detect leakage current.

They are available in modular version (RD2 range and the new RD3 electronic residual current relay range) and in front panel versions (RD range).

A common range of toroidal transformers is available for all the residual current relays.

and earth fault current in a single device.

DS201 and DS202C are equipped with clear indication fl ags.

The internal contact position allows an exact information of the circuit-breaker status: “green”, open contacts; “red”, closed contacts, independently of the toggle position. Any earth fault can be immediately identifi ed through the blue indicator, that signals


3/3ABB SACE

3

Index

RCCBs F 200 seriesTechnical features of RCCBs F 200 series ............................................................................ 3/4F 200 AC ................................................................................................................................ 3/6F 200 AC (for overseas market) ............................................................................................. 3/7F 200 A .................................................................................................................................. 3/8F 200 left neutral .................................................................................................................... 3/9F 200 AP-R AC .................................................................................................................... 3/11F 200 AP-R A ....................................................................................................................... 3/12F 200 AC S .......................................................................................................................... 3/13F 200 A S ............................................................................................................................. 3/14F 200 A 400 Hz, F 200 A 16 2/3 Hz ..................................................................................... 3/15F 200 B ................................................................................................................................ 3/16F 200 PV B .......................................................................................................................... 3/18

RCD-blocks DDA 200 seriesTechnical features of RCD-blocks DDA 200 series ............................................................. 3/20DDA 200 AC ........................................................................................................................ 3/22DDA 200 A ........................................................................................................................... 3/23DDA 200 special version 110 V and 400 V .......................................................................... 3/24DDA 200 AC AP-R ............................................................................................................... 3/25DDA 200 A AP-R ................................................................................................................. 3/25DDA 200 A AE ..................................................................................................................... 3/26DDA 200 AC S ..................................................................................................................... 3/27DDA 200 A S ....................................................................................................................... 3/28DDA 200 B ........................................................................................................................... 3/29

RCBOs DS201 and DS202C seriesTechnical features of RCBOs DS201 series ........................................................................ 3/30DS201 L AC ......................................................................................................................... 3/32DS201 L A ........................................................................................................................... 3/32DS201 L APR ....................................................................................................................... 3/33DS201 AC ............................................................................................................................ 3/34DS201 APR .......................................................................................................................... 3/35DS201 A .............................................................................................................................. 3/36DS201 M AC ........................................................................................................................ 3/38DS201 M APR ..................................................................................................................... 3/39DS201 M A .......................................................................................................................... 3/40Technical features of RCBOs DS202C series...................................................................... 3/42DS202C A ............................................................................................................................ 3/44DS202C M A ........................................................................................................................ 3/46DS202C M APR ................................................................................................................... 3/47

RCBOs DS 200 seriesTechnical features of RCBOs DS 200 series ....................................................................... 3/48DS 200 AC B ....................................................................................................................... 3/50DS 200 AC C ....................................................................................................................... 3/51DS 200 A B .......................................................................................................................... 3/52DS 200 A C .......................................................................................................................... 3/53DS 200 A K .......................................................................................................................... 3/54DS 200 M AC B ................................................................................................................... 3/55DS 200 M AC C ................................................................................................................... 3/56DS 200 M A B ...................................................................................................................... 3/57DS 200 M A C ...................................................................................................................... 3/58

Residual current devicesF 200, DDA 200 and DS 200 series


3/4 ABB

3

Technical featuresRCCBs F 200 series

System pro M compact®

F 200

TECHNICAL FEATURESStandards

Electrical Type (wave form of the earth leakage sensed)features Poles

Rated current In A

Rated sensitivity IΔn ARated voltage Ue IEC V

UL/CSA VInsulation voltage Ui VMax. operating voltage of circuit test IEC V

UL/CSA VMin. operating voltage of circuit test VRated frequency HzRated conditional short-circuit current Inc=IΔc SCPD - fuse gG 100 A kA

kARated impulse withstand voltage (1.2/50) Uimp kVDielectric test voltage at ind. freq. for 1 min. kVOvervoltage categorySurge current resistance (wave 8/20) A

Mechanical Togglefeatures Contact position indicator (CPI)

Electrical lifeMechanical lifeProtection degree housing

terminalsTropicalization humid heat °C/RHacc. to IEC/EN 60068-2 constant climatic conditions °C/RH

variable climatic conditions °C/RHAmbient temperature (with daily average ≤ +35 °C) IEC °C

UL/CSA °CStorage temperature °C

Installation Terminal typeTerminal size top/bottom for cable IEC mm2

UL/CSA AWGTerminal size top/bottom for busbar IEC mm2

UL/CSA AWGTightening torque IEC N*m

UL/CSA in-lbs.ToolMountingConnectionWithdrawal from busbar

Dimensions Dimensions (H x D x W) 2P mmand weight 4P mm

Weight 2P g4P g

Combination Combinable with: auxiliary contactwith auxiliary signal contact/auxiliary switchelements shunt trip

undervoltage release � Ground-fault sensing and relaying equipment-component (up to 63 A)� prior to connection of aluminium conductors (≥ 4 mm2) ensure that their contact points are cleaned, brushed and coated with grease


3/5ABB

3

Technical featuresRCCBs F 200 series


F 200

F200 AC F200 A F200 AC AP-R F200 A AP-R F200 AC S F200 A S F200 A 400 Hz F200 A 16 2/3 HzIEC/EN 61008, UL 1053 � IEC/EN 61008 IEC/EN 61008

AC A AC A AC A A A2P, 4P (for 125 A only 4P) 4P 2P, 4P

16, 25, 40, 63, 80, 100, 125 25, 40, 63 25, 40, 63, 80, 100, 125

40, 63 40, 63, 80, 100, 125

25, 40 63

0.01-0.03-0.1-0.3-0.5 0.03 0.1-0.3-0.5-1 0.03 0.03-0.3-0.5230/400 - 240/415

480Y/277 (up to 63 A) -500

254 (440 for 125 A); 440 for F 200 left neutral 254 254277 (up to 63 A); 480 for F 200 left neutral -

110 (185 for 125 A); 195 for F 200 left neutral 110 11050…60 50...400 16 2/3

10 (for 125 A fuse is gG 125 A)1 (1.25 for 125 A)

62.5

III, disconnector abilities250 3000 5000 250 250

blue sealable in ON-OFF positionyes

10000 (2000 for 125 A) 10000 1000020000 (5000 for 125 A) 20000 20000

IP4XIP2X

28 cycles with 55/95…10023/83 - 40/93 - 55/20

25/95 - 40/95-25…+55 (-25...+40 for 125 A) -25...+55 -25...+55

-35…+70 (up to 63 A) --40…+70

failsafe bi-directional cylinder-lift terminal at top and bottom (shock protected) (cage for In > 63 A) �25/25 (35/35 single slot terminal for In > 63 A) 25/25 25/25

18-4 (up to 63 A) -10/10 (not for In = 80-100 A) 10/10 10/10

18-8 (up to 63 A) -2.8 (3 for In = 125 A) 2.8 2.8

25 (up to 63 A) -Nr. 2 Pozidriv

on DIN rail EN 60715 (35 mm) by means of fast clip devicefrom top and bottom

it is possible without using any tools only from the bottom (not for 125 A)85 x 69 x 35

85 x 69 x 70 (85 x 69.5 x 72 for 125 A)-

85 x 69 x 70 85 x 69 x 70200 -

350 (380 for In = 80 and 100 A and 460 for In = 125A) 350 350yes (no for 125 A) yes yes

yes yes yesyes (no for 125 A) yes yesyes (no for 125 A) yes yes


3/6 ABB

3

Technical details .......................... pag. 11/76 Overall dimensions ........................ pag. 13/6

Selection tablesRCCBs F 200 seriesAC w type


F 200 AC

F 200 AC typeFunction: protection against the effects of sinusoidal alternating earth fault currents; protection against indirect contacts and additional protection against direct (with IΔn=30 mA) contacts.

Application: residential, commercial, industrial.

Standard: IEC/EN 61008

Marking: according to EN 61008

Number Rated Rated Order Bbn Price Price Weight Packof poles residual current details 8012542 1 piece group 1 piece unit current

IΔn mA In A Type code Order code EAN kg pc.

2 10 16 F202 AC-16/0.01 2CSF202001R0160 779902 0.225 1/6

30 25 F202 AC-25/0.03 2CSF202001R1250 780007 0.225 1/6

40 F202 AC-40/0.03 2CSF202001R1400 780106 0.225 1/6

63 F202 AC-63/0.03 2CSF202001R1630 780205 0.225 1/6

80 F202 AC-80/0.03 2CSF202001R1800 914204 0.225 1/6

100 F202 AC-100/0.03 2CSF202001R1900 914303 0.225 1/6

100 25 F202 AC-25/0.1 2CSF202001R2250 780304 0.225 1/6

40 F202 AC-40/0.1 2CSF202001R2400 780403 0.225 1/6

63 F202 AC-63/0.1 2CSF202001R2630 780502 0.225 1/6

80 F202 AC-80/0.1 2CSF202001R2800 914402 0.225 1/6

100 F202 AC-100/0.1 2CSF202001R2900 914501 0.225 1/6

300 25 F202 AC-25/0.3 2CSF202001R3250 780601 0.225 1/6

40 F202 AC-40/0.3 2CSF202001R3400 780700 0.225 1/6

63 F202 AC-63/0.3 2CSF202001R3630 780809 0.225 1/6

80 F202 AC-80/0.3 2CSF202001R3800 914600 0.225 1/6

100 F202 AC-100/0.3 2CSF202001R3900 914709 0.225 1/6

500 25 F202 AC-25/0.5 2CSF202001R4250 780908 0.225 1/6

40 F202 AC-40/0.5 2CSF202001R4400 781004 0.225 1/6

63 F202 AC-63/0.5 2CSF202001R4630 781103 0.225 1/6

80 F202 AC-80/0.5 2CSF202001R4800 914808 0.225 1/6

100 F202 AC-100/0.5 2CSF202001R4900 914907 0.225 1/6

4 30 25 F204 AC-25/0.03 2CSF204001R1250 781202 0.375 1/3

40 F204 AC-40/0.03 2CSF204001R1400 781301 0.375 1/3

63 F204 AC-63/0.03 2CSF204001R1630 781400 0.375 1/3

80 F204 AC-80/0.03 2CSF204001R1800 916604 0.405 1/3

100 F204 AC-100/0.03 2CSF204001R1900 916703 0.405 1/3

125 F204 AC-125/0.03 2CSF204001R1950 941507 0.500 1

100 25 F204 AC-25/0.1 2CSF204001R2250 781509 0.375 1/3

40 F204 AC-40/0.1 2CSF204001R2400 781608 0.375 1/3

63 F204 AC-63/0.1 2CSF204001R2630 781707 0.375 1/3

80 F204 AC-80/0.1 2CSF204001R2800 916802 0.405 1/3

100 F204 AC-100/0.1 2CSF204001R2900 916901 0.405 1/3

125 F204 AC-125/0.1 2CSF204001R2950 941606 0.500 1

300 25 F204 AC-25/0.3 2CSF204001R3250 781806 0.375 1/3

40 F204 AC-40/0.3 2CSF204001R3400 781905 0.375 1/3

63 F204 AC-63/0.3 2CSF204001R3630 782001 0.375 1/3

80 F204 AC-80/0.3 2CSF204001R3800 917007 0.405 1/3

100 F204 AC-100/0.3 2CSF204001R3900 917106 0.405 1/3

125 F204 AC-125/0.3 2CSF204001R3950 941705 0.500 1

500 25 F204 AC-25/0.5 2CSF204001R4250 782100 0.375 1/3

40 F204 AC-40/0.5 2CSF204001R4400 782209 0.375 1/3

63 F204 AC-63/0.5 2CSF204001R4630 782308 0.375 1/3

80 F204 AC-80/0.5 2CSF204001R4800 917205 0.405 1/3

100 F204 AC-100/0.5 2CSF204001R4900 917304 0.405 1/3

125 F204 AC-125/0.5 2CSF204001R4950 941804 0.500 1

AC2C

SC

4005

65F0

201

2CS

C40

0569

F020

12C

SC

4001

97F0

201


3/7ABB

3


Selection tablesRCCBs F 200 series AC w type, for overseas markets


F 200 AC for overseas

markets

AC2C

SC

4005

65F0

201

2CS

C40

0569

F020

1

F 200 AC type (for overseas markets) Function: protection against the effects of sinusoidal alternating earth fault currents; protection against indirect contacts and additional protection against direct (with IΔn=30 mA) contacts.



Marking: according to IEC 61008

Number Rated Rated Order Bbn Price Price Weight Packof poles residual current details 8012542 1 piece group 1 piece unit current IΔn mA In A Type code Order code EAN kg pc.

2 10 16 F202 AC-16/0.01 2CSF202005R0160 814603 0.225 1/6

30 25 F202 AC-25/0.03 2CSF202005R1250 814702 0.225 1/6

40 F202 AC-40/0.03 2CSF202005R1400 814801 0.225 1/6

63 F202 AC-63/0.03 2CSF202005R1630 814900 0.225 1/6

80 F202 AC-80/0.03 2CSF202005R1800 935902 0.225 1/6

100 F202 AC-100/0.03 2CSF202005R1900 936008 0.225 1/6

100 25 F202 AC-25/0.1 2CSF202005R2250 815006 0.225 1/6

40 F202 AC-40/0.1 2CSF202005R2400 815105 0.225 1/6

63 F202 AC-63/0.1 2CSF202005R2630 815204 0.225 1/6

80 F202 AC-80/0.1 2CSF202005R2800 936107 0.225 1/6

100 F202 AC-100/0.1 2CSF202005R2900 936206 0.225 1/6

300 25 F202 AC-25/0.3 2CSF202005R3250 815303 0.225 1/6

40 F202 AC-40/0.3 2CSF202005R3400 815402 0.225 1/6

63 F202 AC-63/0.3 2CSF202005R3630 815501 0.225 1/6

80 F202 AC-80/0.3 2CSF202005R3800 936305 0.225 1/6

100 F202 AC-100/0.3 2CSF202005R3900 936404 0.225 1/6

500 80 F202 AC-80/0.5 2CSF202005R4800 936503 0.225 1/6

100 F202 AC-100/0.5 2CSF202005R4900 936602 0.225 1/6 4 30 25 F204 AC-25/0.03 2CSF204005R1250 817109 0.375 1/3

40 F204 AC-40/0.03 2CSF204005R1400 817208 0.375 1/3

63 F204 AC-63/0.03 2CSF204005R1630 817307 0.375 1/3

80 F204 AC-80/0.03 2CSF204005R1800 936701 0.405 1/3

100 F204 AC-100/0.03 2CSF204005R1900 936800 0.405 1/3

100 25 F204 AC-25/0.1 2CSF204005R2250 817406 0.375 1/3

40 F204 AC-40/0.1 2CSF204005R2400 817505 0.375 1/3

63 F204 AC-63/0.1 2CSF204005R2630 817604 0.375 1/3

80 F204 AC-80/0.1 2CSF204005R2800 936909 0.405 1/3

100 F204 AC-100/0.1 2CSF204005R2900 937005 0.405 1/3

300 25 F204 AC-25/0.3 2CSF204005R3250 817703 0.375 1/3

40 F204 AC-40/0.3 2CSF204005R3400 817802 0.375 1/3

63 F204 AC-63/0.3 2CSF204005R3630 817901 0.375 1/3

80 F204 AC-80/0.3 2CSF204005R3800 937104 0.405 1/3

100 F204 AC-100/0.3 2CSF204005R3900 937203 0.405 1/3

500 80 F204 AC-80/0.5 2CSF204005R4800 937302 0.405 1/3

100 F204 AC-100/0.5 2CSF204005R4900 937401 0.405 1/3


3/8 ABB

3


Selection tablesRCCBs F 200 seriesA y type


F 200 A

A F 200 A typeFunction: protection against the effects of sinusoidal alternating and direct pulsating earth fault currents; protection against indirect contacts and additional protection against direct (with IΔn=30 mA) contacts.






2 10 16 F202 A-16/0.01 2CSF202101R0160 782407 0.225 1/6

30 25 F202 A-25/0.03 2CSF202101R1250 782506 0.225 1/6

40 F202 A-40/0.03 2CSF202101R1400 782605 0.225 1/6

63 F202 A-63/0.03 2CSF202101R1630 782704 0.225 1/6

80 F202 A-80/0.03 2CSF202101R1800 915201 0.225 1/6

100 F202 A-100/0.03 2CSF202101R1900 915300 0.225 1/6

100 25 F202 A-25/0.1 2CSF202101R2250 786900 0.225 1/6

40 F202 A-40/0.1 2CSF202101R2400 787006 0.225 1/6

63 F202 A-63/0.1 2CSF202101R2630 787105 0.225 1/6

80 F202 A-80/0.1 2CSF202101R2800 915409 0.225 1/6

100 F202 A-100/0.1 2CSF202101R2900 915508 0.225 1/6

300 25 F202 A-25/0.3 2CSF202101R3250 782803 0.225 1/6

40 F202 A-40/0.3 2CSF202101R3400 782902 0.225 1/6

63 F202 A-63/0.3 2CSF202101R3630 783008 0.225 1/6

80 F202 A-80/0.3 2CSF202101R3800 915607 0.225 1/6

100 F202 A-100/0.3 2CSF202101R3900 915706 0.225 1/6

500 25 F202 A-25/0.5 2CSF202101R4250 783107 0.225 1/6

40 F202 A-40/0.5 2CSF202101R4400 783206 0.225 1/6

63 F202 A-63/0.5 2CSF202101R4630 783305 0.225 1/6

80 F202 A-80/0.5 2CSF202101R4800 915805 0.225 1/6

100 F202 A-100/0.5 2CSF202101R4900 915904 0.225 1/6

4 30 25 F204 A-25/0.03 2CSF204101R1250 783404 0.375 1/3

40 F204 A-40/0.03 2CSF204101R1400 783503 0.375 1/3

63 F204 A-63/0.03 2CSF204101R1630 783602 0.375 1/3

80 F204 A-80/0.03 2CSF204101R1800 917809 0.405 1/3

100 F204 A-100/0.03 2CSF204101R1900 917908 0.405 1/3

125 F204 A-125/0.03 2CSF204101R1950 941903 0.500 1

100 25 F204 A-25/0.1 2CSF204101R2250 787204 0.375 1/3

40 F204 A-40/0.1 2CSF204101R2400 787303 0.375 1/3

63 F204 A-63/0.1 2CSF204101R2630 787402 0.375 1/3

80 F204 A-80/0.1 2CSF204101R2800 918004 0.405 1/3

100 F204 A-100/0.1 2CSF204101R2900 918103 0.405 1/3

125 F204 A-125/0.1 2CSF204101R2950 942009 0.500 1

300 25 F204 A-25/0.3 2CSF204101R3250 783701 0.375 1/3

40 F204 A-40/0.3 2CSF204101R3400 783800 0.375 1/3

63 F204 A-63/0.3 2CSF204101R3630 783909 0.375 1/3

80 F204 A-80/0.3 2CSF204101R3800 918202 0.405 1/3

100 F204 A-100/0.3 2CSF204101R3900 918301 0.405 1/3

125 F204 A-125/0.3 2CSF204101R3950 942108 0.500 1

500 25 F204 A-25/0.5 2CSF204101R4250 784005 0.375 1/3

40 F204 A-40/0.5 2CSF204101R4400 784104 0.375 1/3

63 F204 A-63/0.5 2CSF204101R4630 784203 0.375 1/3

80 F204 A-80/0.5 2CSF204101R4800 918400 0.405 1/3

100 F204 A-100/0.5 2CSF204101R4900 918509 0.405 1/3

125 F204 A-125/0.5 2CSF204101R4950 942207 0.500 1

2CS

C40

0565

F020

12C

SC

4005

69F0

201

2CS

C40

0197

F020

1


3/9ABB

3


AC F 200 AC type with neutral pole on the leftFunction: protection against the effects of sinusoidal alternating earth fault currents; protection against indirect contacts and additional protection against direct (with IΔn=30 mA) contacts. Product helpful where for installation habits, for wiring with busbars or cables, for special needs neutral on the left is needed.






4 30 25 F204 AC-25/0.03 2CSF204023R1250 815907 0.375 1/3 40 F204 AC-40/0.03 2CSF204023R1400 816003 0.375 1/3 63 F204 AC-63/0.03 2CSF204023R1630 816102 0.375 1/3 80 F204 AC-80/0.03 2CSF204023R1800 917403 0.405 1/3 100 F204 AC-100/0.03 2CSF204023R1900 917502 0.405 1/3 125 F204 AC-125/0.03 2CSF204023R1950 975106 0.500 1 100 25 F204 AC-25/0.1 2CSF204023R2250 816201 0.375 1/3 40 F204 AC-40/0.1 2CSF204023R2400 816300 0.375 1/3 63 F204 AC-63/0.1 2CSF204023R2630 816409 0.375 1/3 300 25 F204 AC-25/0.3 2CSF204023R3250 816508 0.375 1/3 40 F204 AC-40/0.3 2CSF204023R3400 816607 0.375 1/3 63 F204 AC-63/0.3 2CSF204023R3630 816706 0.375 1/3 80 F204 AC-80/0.3 2CSF204023R3800 917601 0.405 1/3 100 F204 AC-100/0.3 2CSF204023R3900 917700 0.405 1/3 125 F204 AC-125/0.3 2CSF204023R3950 975304 0.500 1 500 25 F204 AC-25/0.5 2CSF204023R4250 816805 0.375 1/3 40 F204 AC-40/0.5 2CSF204023R4400 816904 0.375 1/3 63 F204 AC-63/0.5 2CSF204023R4630 817000 0.375 1/3

N 1/2

N 2/1

3/4

4/3

5/6

6/5

2CS

C40

0571

F020

12C

SC

4001

97F0

201

Selection tablesRCCBs F 200 seriesAC w type left neutral


F 200 left neutral


3/10 ABB

3


Selection tablesRCCBs F 200 seriesA y type left neutral


F 200 left neutral

F 200 A type with neutral pole on the leftFunction: protection against the effects of sinusoidal alternating and direct pulsating earth fault cur-rents; protection against indirect contacts and additional protection against direct (with IΔn=30 mA) contacts. Product helpful where for installation habits, for wiring with busbars or cables, for special needs neutral on the left is needed.






4 30 25 F204 A-25/0.03 2CSF204123R1250 820109 0.375 1/3 40 F204 A-40/0.03 2CSF204123R1400 820208 0.375 1/3 63 F204 A-63/0.03 2CSF204123R1630 820307 0.375 1/3 80 F204 A-80/0.03 2CSF204123R1800 918608 0.405 1/3 100 F204 A-100/0.03 2CSF204123R1900 918707 0.405 1/3 125 F204 A-125/0.03 2CSF204123R1950 967705 0.500 1 100 25 F204 A-25/0.1 2CSF204123R2250 820406 0.375 1/3 40 F204 A-40/0.1 2CSF204123R2400 820505 0.375 1/3 63 F204 A-63/0.1 2CSF204123R2630 820604 0.375 1/3 300 25 F204 A-25/0.3 2CSF204123R3250 820703 0.375 1/3 40 F204 A-40/0.3 2CSF204123R3400 820802 0.375 1/3 63 F204 A-63/0.3 2CSF204123R3630 820901 0.375 1/3 80 F204 A-80/0.3 2CSF204123R3800 918806 0.405 1/3 100 F204 A-100/0.3 2CSF204123R3900 918905 0.405 1/3 125 F204 A-125/0.3 2CSF204123R3950 967804 0.500 1 500 25 F204 A-25/0.5 2CSF204123R4250 821007 0.375 1/3 40 F204 A-40/0.5 2CSF204123R4400 821106 0.375 1/3 63 F204 A-63/0.5 2CSF204123R4630 821205 0.375 1/3

A

N 1/2

N 2/1

3/4

4/3

5/6

6/5

2CS

C40

0197

F020

12C

SC

4005

71F0

201


3/11ABB

3


Selection tablesRCCBs F 200 series AC w type, AP-R (high immunity)


F 200 AC AP-R

F 200 AP-R, AC typeFunction: protection against the effects of sinusoidal alternating earth fault currents, providing the best compromise between safety and continuity in the service thanks to the resistance to unwanted trippings; protection against indirect contacts and additional protection against direct (IΔn=30 mA) contacts.



Surge current resistance (wave 8/20)=3000 A



2 30 25 F202 AC-25/0.03 AP-R 2CSF202301R1250 785705 0.225 1/6

40 F202 AC-40/0.03 AP-R 2CSF202301R1400 823704 0.225 1/6

63 F202 AC-63/0.03 AP-R 2CSF202301R1630 785804 0.225 1/6

4 30 25 F204 AC-25/0.03 AP-R 2CSF204301R1250 785903 0.375 1/3

40 F204 AC-40/0.03 AP-R 2CSF204301R1400 823803 0.375 1/3

63 F204 AC-63/0.03 AP-R 2CSF204301R1630 786009 0.375 1/3

AC2C

SC

4005

65F0

201

2CS

C40

0569

F020

1


3/12 ABB

3


A

Selection tablesRCCBs F 200 seriesA y type, AP-R (high immunity)


F 200 A AP-R

F 200 AP-R, A typeFunction: protection against the effects of sinusoidal alternating and direct pulsating earth fault currents, providing the best compromise between safety and continuity in the service thanks to the resistance to unwanted trippings; protection against indirect contacts and additional protection against direct (IΔn=30 mA) contacts.







2 30 25 F202 A-25/0.03 AP-R 2CSF202401R1250 785101 0.225 1/6

40 F202 A-40/0.03 AP-R 2CSF202401R1400 785200 0.225 1/6

63 F202 A-63/0.03 AP-R 2CSF202401R1630 785309 0.225 1/6

80 F202 A-80/0.03 AP-R 2CSF202401R1800 916406 0.225 1/6

100 F202 A-100/0.03 AP-R 2CSF202401R1900 916505 0.225 1/6

4 30 25 F204 A-25/0.03 AP-R 2CSF204401R1250 785408 0.375 1/3

40 F204 A-40/0.03 AP-R 2CSF204401R1400 785507 0.375 1/3

63 F204 A-63/0.03 AP-R 2CSF204401R1630 785606 0.375 1/3

80 F204 A-80/0.03 AP-R 2CSF204401R1800 919407 0.405 1/3

100 F204 A-100/0.03 AP-R 2CSF204401R1900 919506 0.405 1/3

125 F204 A-125/0.03 AP-R 2CSF204401R1950 967903 0.500 1

2CS

C40

0565

F020

12C

SC

4005

69F0

201

2CS

C40

0197

F020

1


3/13ABB

3


Selection tablesRCCBs F 200 series AC w type, selective


F 200 AC S

AC F 200 AC selective typeFunction: protection against the effects of sinusoidal alternating earth fault currents with an intentional tripping delay, which permits to realize the selectivity with downstream instantaneous devices (for more information about selectivity see the technical guide); protection against indirect contacts.

Application: commercial, industrial.





2 100 40 F202 AC S-40/0.1 2CSF202901R2400 821304 0.225 1/6

63 F202 AC S-63/0.1 2CSF202901R2630 821403 0.225 1/6

300 40 F202 AC S-40/0.3 2CSF202901R3400 821502 0.225 1/6

63 F202 AC S-63/0.3 2CSF202901R3630 821601 0.225 1/6

500 40 F202 AC S-40/0.5 2CSF202901R4400 821700 0.225 1/6

63 F202 AC S-63/0.5 2CSF202901R4630 821809 0.225 1/6

1000 40 F202 AC S-40/1 2CSF202901R5400 821908 0.225 1/6

63 F202 AC S-63/1 2CSF202901R5630 822004 0.225 1/6

4 100 40 F204 AC S-40/0.1 2CSF204901R2400 822103 0.375 1/3

63 F204 AC S-63/0.1 2CSF204901R2630 822202 0.375 1/3

300 40 F204 AC S-40/0.3 2CSF204901R3400 822301 0.375 1/3

63 F204 AC S-63/0.3 2CSF204901R3630 822400 0.375 1/3

500 40 F204 AC S-40/0.5 2CSF204901R4400 822509 0.375 1/3

63 F204 AC S-63/0.5 2CSF204901R4630 822608 0.375 1/3

1000 40 F204 AC S-40/1 2CSF204901R5400 822707 0.375 1/3

63 F204 AC S-63/1 2CSF204901R5630 822806 0.375 1/3

2CS

C40

0565

F020

12C

SC

4005

69F0

201


3/14 ABB

3


Selection tablesRCCBs F 200 seriesA y type, selective


F 200 A S

A F 200 A selective typeFunction: protection against the effects of sinusoidal alternating and direct pulsating earth fault currents with an intentional tripping delay, which permits to realize the selectivity with downstream instantaneous devices (for more information about selectivity see the technical guide); protection against indirect contacts.







2 100 40 F202 A S-40/0.1 2CSF202201R2400 822905 0.225 1/6

63 F202 A S-63/0.1 2CSF202201R2630 823001 0.225 1/6

100 F202 A S-100/0.1 2CSF202201R2900 916000 0.225 1/6

300 40 F202 A S-40/0.3 2CSF202201R3400 784302 0.225 1/6

63 F202 A S-63/0.3 2CSF202201R3630 784401 0.225 1/6

100 F202 A S-100/0.3 2CSF202201R3900 916109 0.225 1/6

500 40 F202 A S-40/0.5 2CSF202201R4400 784500 0.225 1/6

63 F202 A S-63/0.5 2CSF202201R4630 784609 0.225 1/6

100 F202 A S-100/0.5 2CSF202201R4900 916208 0.225 1/6

1000 40 F202 A S-40/1 2CSF202201R5400 823100 0.225 1/6

63 F202 A S-63/1 2CSF202201R5630 823209 0.225 1/6

100 F202 A S-100/1 2CSF202201R5900 916307 0.225 1/6

4 100 40 F204 A S-40/0.1 2CSF204201R2400 823308 0.375 1/3

63 F204 A S-63/0.1 2CSF204201R2630 823407 0.375 1/3

100 F204 A S-100/0.1 2CSF204201R2900 919001 0.405 1/3

300 40 F204 A S-40/0.3 2CSF204201R3400 784708 0.375 1/3

63 F204 A S-63/0.3 2CSF204201R3630 784807 0.375 1/3

100 F204 A S-100/0.3 2CSF204201R3900 919100 0.405 1/3

125 F204 A S-125/0.3 2CSF204201R3950 968207 0.500 1

500 40 F204 A S-40/0.5 2CSF204201R4400 784906 0.375 1/3

63 F204 A S-63/0.5 2CSF204201R4630 785002 0.375 1/3

100 F204 A S-100/0.5 2CSF204201R4900 919209 0.405 1/3

125 F204 A S-125/0.5 2CSF204201R4950 968405 0.500 1

1000 40 F204 A S-40/1 2CSF204201R5400 823506 0.375 1/3

63 F204 A S-63/1 2CSF204201R5630 823605 0.375 1/3

100 F204 A S-100/1 2CSF204201R5900 919308 0.405 1/3

2CS

C40

0565

F020

12C

SC

4005

69F0

201

2CS

C40

0197

F020

1


3/15ABB

3


Selection tablesRCCBs F 200 series A y type for high frequency and railways applications


F 200 A 400 HzF 200 A 16 2/3 Hz

A F 200 A type for high frequency (400 Hz)Function: protection against the effects of sinusoidal alternating and direct pulsating earth fault currents; protection against indirect contacts and additional protection against direct (with Idn=30 mA) contacts.Advantages: increasing the frequency generates an increase of the magnetic reluctance of the toroi-dal transformer of standard RCCB and what follows is the value of the increasing operating residual current at 400 Hz reaching values 3 or more times higher than those of the residual current at 50Hz. The RCCB F 200 400 Hz guarantees protection against indirect contacts and additional protection against direct (with IΔn=30 mA) contacts considering that the operating residual current doesn’t increase with the increase of the network frequency.





4 30 25 F204 A-25/0.03 400Hz 2CSF204197R1250 968603 0.375 1/3

40 F204 A-40/0.03 400Hz 2CSF204197R1400 968702 0.375 1/3

2CS

C40

0569

F020

1

A F200 A type 16 2/3 HzFunction: protection against the effects of sinusoidal alternating and direct pulsating earth faultcurrents; protection against indirect contacts and additional protection against direct (with IΔn=30 mA) contacts.The RCCB F200 16 2/3 Hz can work at rated frequency of 16 2/3 Hz which is common in railways applications

Application: railways

Standard: IEC/ EN 61008



2 30 63 F202 A-63/0.03 16-2/3Hz 2CSF202196R1630 734536 0.225 1/6

300 63 F202 A-63/0.3 16-2/3Hz 2CSF202196R3630 733638 0.225 1/6

500 63 F202 A-63/0.5 16-2/3Hz 2CSF202196R4630 734437 0.225 1/6

4 30 63 F204 A-63/0.03 16-2/3Hz 2CSF204196R1630 733539 0.375 1/3

300 63 F204 A-63/0.3 16-2/3Hz 2CSF204196R3630 734338 0.375 1/3

500 63 F204 A-63/0.5 16-2/3Hz 2CSF204196R4630 733430 0.375 1/3

2CS

C40

0569

F020

1


3/16 ABB

3


Selection tablesRCCBs F 200 series B y type, B y type selective


F 200 B

B F 200 B type for smooth DC earth fault currentFunction: protection against the effects of sinusoidal alternating, direct pulsating and pulsating DC or smooth DC earth fault currents; protection against indirect contacts andadditional protection against direct (with IΔn=30 mA) contacts.

Application: industrial.

Standard: IEC/EN 61008, IEC 62423




4 30 40 F204 B-40/0.03 2CSF204501R1400 988403 0.500 1

63 F204 B-63/0.03 2CSF204501R1630 988502 0.500 1

125 � F204 B-125/0.03 2CSF204523R1950 988700 0.500 1

300 63 F204 B-63/0.3 2CSF204501R3630 989004 0.500 1

125 � F204 B-125/0.3 2CSF204523R3950 989202 0.500 1

500 125 � F204 B-125/0.5 2CSF204523R4950 730439 0.500 1

� Devices with rated current In=125 A are with neutral on the left

F 200 B selective type for smooth DC earth fault currentFunction: protection against the effects of sinusoidal alternating, direct pulsating and pulsating DCor smooth DC earth fault currents with an intentional tripping delay, which permits to realize theselectivity with downstream instantaneous devices (for more information about selectivity see thetechnical guide); protection against indirect contacts.


Standard: IEC/EN 61008, IEC 62423





4 300 63 F204 B S-63/0.3 2CSF204801R3630 989301 0.500 1

125 � F204 B S-125/0.3 2CSF204823R3950 989509 0.500 1

500 125 � F204 B S-125/0.5 2CSF204823R4950 731238 0.500 1

� Devices with rated current In=125 A are with neutral on the left

2CS

C40

0197

F000

12C

SC

4001

97F0

001

1/2 3/4 5/6 7/8/N

T

Input

Output2/1 4/3 6/5 8/7/N

N 3 5 7

T

Input

OutputN 4 6 8

1/2 3/4 5/6 7/8/N

T

Input

Output2/1 4/3 6/5 8/7/N

N 3 5 7

T

Input

OutputN 4 6 8


3/17ABB

3


Selection tablesRCCBs F 200 series - B y type for continuous, selective continuous type fault currents


F 200 B

Type (wave form of the detected dispersion current) BRated current In [A] 40 63 125No. of poles 4Rated voltage Un [V] 230/400Working range of test circuit [V] 185 V AC-440 V ACRated conditional short-circuit current Inc [kA] 10Rated conditional residual short-circuit current IΔc [kA] 10Rated making and breaking capacity Im [A] 500 800 1250Rated residual making and breaking capacity IΔm [A] 500 800 1250Surge current resistance ring wave 0,5 ms/100 kHz: 200 A, impulse 8/20 μs: 3 kA

(impulse 8/20 μs: 5 kA for F200 type B S - selective)Rated sensitivity IΔn [A] 0.03 0.03-0.3 0.03-0.3-0.5Working frequency range [Hz] 0-1000Min. operating voltagefor detecting type A/AC residual currents [V] 0 Vfor detecting type B residual currents [V] 30 V a.c.Own consumption [W] max. 3.5Dissipated power Pv [W] 2.9 7.2 28Short-circuit fuse acc. to VDE 0636/IEC 60269-1 80 A/gL 100 A/gG 125 A/gLTripping time F200 type B [ms] 1 x IΔn ≤ 300 ms; 5 x IΔn ≤ 40 msTripping time F200 type B S [ms] 1 x IΔn > 130 ms ≤ 500 ms; 5 x IΔn > 50 ms ≤ 150 msToggle Blue sealable in ON/OFF positionImpact resistance 20 g/20 msProtection degree IP40 (after installation in distribution board)Supply terminal 1, 3, 5, 7Ambient temperature [°C] -25…+40Resistance to climate changes acc. to IEC 68-2-30 25 °C/55 °C; 93%/97% relative humidity, 28 cyclesCables max. size [mm2] 1x1.5-50 mm2; 2x1.5-16 mm2 Terminal size [mm2] 50Tightening torque [N*m] 3Mechanical life > 5000Electrical life > 2000Electromagnetic compatibility IEC 61453; DIN VDE 0664 Pt.30Mounting on DIN rail EN 60715 (35 mm) by means of fast clip deviceDimensions (H x P x L) [mm] 85 x 69,5 x 70Weight 4P [g] 500


3/18 ABB

3


Selection tablesRCCBs F 200 series PV B y type


F 200 PV B

B F200 PV B type for smooth DC earth fault current for photovoltaic applicationsFunction: protection against the effects of sinusoidal alternating, direct pulsanting and pulsanting DC or smooth DC earth fault currents; protection against indirect contacts and additional protection against direct (with IΔn=30mA) contacts. Where an electrical installation includes a PV power supply system without at least simple separation between the AC side and the DC side, an RCD installed to provide fault protection by automatic disconnection of supply should be type B according to IEC 60755, amendment 2 (according to IEC 60364-7 art. 712.413.1.1.1.2)

Application: particularly suitable for use in solar energy (photovoltaic) systems

standard: IEC/EN 61008, IEC 62423



2 30 25 F202PV B-25/0,03 2CSF202601R1250 071235 0.500 1

63 F202PV B-63/0,03 2CSF202601R1630 368632 0.500 1

300 25 F202PV B-25/0,3 2CSF202601R3250 910831 0.500 1

63 F202PV B-63/0,3 2CSF202601R3630 659037 0.500 1

5 7

6 8

T

2CS

C40

0676

F000

1


3/19ABB

3


Selection tablesRCCBs F 200 series PV B y type


F 200 PV B

Rated current In 25A 63 A

Rated sensitivity IΔn 0.03 - 0.3 AWorking frequency range 0 - 1000 HzRated voltage Un 230 V ACRated frequency 50 HzMin. operating voltagefor detecting type A/AC residual currentsfor detecting type B residual currents

0 V (mains voltage-independent)

30 V ACOwn consumption max. 1.2 WWorking range of test circuit 100 V AC – 250 V ACNo. of poles: 2-poleDissipated power Pv 1.2 W 7.2 WShort-circuit fuse to VDE 0636 / IEC 60269-1 100 A/gGTripping times F200PV B type 1xIΔn ≤ 300 ms; 5xIΔn ≤ 40 msRated making and breaking capacity Im 500 A 800 A

Rated residual making and breaking capacity IΔm 500 A 800 ARated short circuit current Inc 10 kA

Rated conditional residual short-circuit current IΔc 10 kASurge current resistance Ring wave 0.5 ms / 100 kHz: 200 A, impulse 8/20 μs: 3 kAImpact resistance 20 g / 20 ms durationEnclosure protection type IP40 (after installation in distribution board)Input side Terminals 5, 7Ambient temperature -25°C to 40°CResistance to climate changes according to IEC 68-2-30 damp / heat cyclic (25°C / 55°C; 93% / 97% rel.hum., 28 cycles)Cables max. size 1x1.5-50 mm2 (1-wire connect.); 2x1.5-16 mm2 (2-wire connect.)Tightening torque of fastening screws 3 NmMechanical life > 5000 switching cyclesElectrical life > 2000 switching cyclesElectromagnetic compatibility IEC 61453; DIN VDE 0664 Pt.30 (interference resistance-industrial environment)Mounting On DIN rail EN 60715 (35 mm) by means of fast clip device; any mounting positionToggle Blue sealable in ON/OFF position.Dimensions (H x D x W) 85 x 69 x 72 mmWeight 500 g


3/20 ABB

3 TECHNICAL FEATURES

Standards

Operating characteristic: typeRated current In [A]PolesRated voltage Ue 2P [V]

3P4P

Insulation voltage Ui [V]Operating voltage of circuit test Ut 2P [V]

3P4P

Rated frequency HzRated breaking capacity according to IEC EN 61009 [A]Rated breaking capacity according to IEC EN 60947-2 [A]Rated residual breaking capacity IΔm [kA]Rated inpulse withstand capacity (1,2/50) Uimp [kV]Dielectric test voltage at ind. freq. for 1 min. [kV]Surge current resistance (wave 8/20) [A]

Rated sensitivity IΔn [A]ToggleElectrical lifeMechanical lifeProtection degree housing

terminalsTropicalization humid heat [°C/RH]according to DIN 40046 IEC 68-2 constant climatic conditions [°C/RH]

variable climatic conditions [°C/RH]Ambient temperature (with daily average ≤ +35 °C) [°C]Storage temperature [°C]Terminal type 2P

3P/4P In=25 and 40 A3P/4P In=63 A

Terminal size 2P [mm2]3P/4P In=25 and 40 A [mm2]3P/4P In=63 A [mm2]

Tightening torque 2P [N*m]3P/4P In=25 and 40 A [N*m]3P/4P In=63 A [N*m]

MountingDimensions 2P [mm]H x P x L 3P/4P In=25 and 40 A [mm]

3P/4P In=63 A [mm]Weight 2P [g]

3P/4P In=25 and 40 A [g]3P/4P In=63 A [g]

Combinable with S 200 LS 200S 200 MS 200 P

� All RCD-blocks DDA 200 with rated current 63 A are provided with two additional terminals for remote tripping.� DDA200 A AE is provided with two additional terminals for remote release in positive safety. A remote control circuit should be connected to those terminals where circuit breakers or push buttons with normally closed contacts should be inserted.

Technical featuresRCD-blocks DDA 200 series


DDA 200


3/21ABB

3DDA 200 AC DDA 200 A DDA 200 AC AP-R

DDA 200 A AP-R DDA 200 A AE DDA 200 AC S DDA 200 A S DDA 200 B

IEC EN 61009 App.G IEC EN 61009 App. G and IEC

60755AC A AC A A AC A B

25, 40, 63 � 25, 40, 63 � 63 � 63 � 632P, 3P, 4P 3P, 4P

230 (400 for special execution @400 V)230/400230/400

230 230230/400230/400

400230 230

500110-254 (400 for special execution @400 V)

195-440 (110-254 for special execution @110 V)195-440 (110-254 for special execution @110 V)

184-264 110-254195-440195-440

310-440 310-440184-264 195-254

50…60same of the coupled MCBsame of the coupled MCBsame of the coupled MCB

42,5

250 3000 250 5000 3000 (5000 for selective types)

0.01-0.03-0.1-0.3-0.5-1 0.03 0.03-0.3-0.5-1 0.1-0.3-0.5-1 0.03 - 0.3blue

1000020000IP4X IP2X

28 cycles with 55/95…10023/83 - 40/93 - 55/20

25/95 - 40/95-25...+55-40…+70

bi-directional cylinder-lift cage type

bi-directional cylinder-lift (rigid or fl exible) up to 25(rigid or fl exible) up to 16

(rigid or fl exible) up to 252.81.2

2.8on DIN rail EN 60715 (35 mm) by means of fast clip device

85 x 69 x 3585 x 69 x 35

85 x 69 x 70175175

325yesyesyesyes

Technical featuresRCD-blocks DDA 200 series


DDA 200


3/22 ABB

3


Selection tablesRCD-blocks DDA 200 series AC w type


DDA 200 AC

AC DDA 200 AC typeFunction: RCD-block for assembly on site with MCBs S 200 series. Protection against the effects of sinusoidal alternating earth fault currents; protection against indirect contacts and additional protection against direct (with IΔn=30 mA) contacts.


Standard: IEC/EN 61009 Ann. G


2 10 25 DDA202 AC-25/0.01 2CSB202001R0250 791003 0.180 1

30 25 DDA202 AC-25/0.03 2CSB202001R1250 791102 0.180 1

40 DDA202 AC-40/0.03 2CSB202001R1400 791201 0.180 1

63 � DDA202 AC-63/0.03 2CSB202001R1630 791300 0.180 1

100 25 DDA202 AC-25/0.1 2CSB202001R2250 791409 0.180 1

40 DDA202 AC-40/0.1 2CSB202001R2400 791508 0.180 1

63 � DDA202 AC-63/0.1 2CSB202001R2630 791607 0.180 1

300 25 DDA202 AC-25/0.3 2CSB202001R3250 791706 0.180 1

40 DDA202 AC-40/0.3 2CSB202001R3400 791805 0.180 1

63 � DDA202 AC-63/0.3 2CSB202001R3630 791904 0.180 1

500 25 DDA202 AC-25/0.5 2CSB202001R4250 792000 0.180 1

40 DDA202 AC-40/0.5 2CSB202001R4400 792109 0.180 1

63 � DDA202 AC-63/0.5 2CSB202001R4630 792208 0.180 1

1000 25 DDA202 AC-25/1 2CSB202001R5250 808305 0.180 1

40 DDA202 AC-40/1 2CSB202001R5400 808404 0.180 1

63 � DDA202 AC-63/1 2CSB202001R5630 792307 0.180 1

2000 63 DDA202 AC-63/2 2CSB202001R6630 792406 0.180 1

3 30 25 DDA203 AC-25/0.03 2CSB203001R1250 792505 0.220 1

40 DDA203 AC-40/0.03 2CSB203001R1400 792604 0.220 1

63 � DDA203 AC-63/0.03 2CSB203001R1630 792703 0.260 1

100 25 DDA203 AC-25/0.1 2CSB203001R2250 792802 0.220 1

40 DDA203 AC-40/0.1 2CSB203001R2400 792901 0.220 1

63 � DDA203 AC-63/0.1 2CSB203001R2630 793007 0.260 1

300 25 DDA203 AC-25/0.3 2CSB203001R3250 793106 0.220 1

40 DDA203 AC-40/0.3 2CSB203001R3400 793205 0.220 1

63 � DDA203 AC-63/0.3 2CSB203001R3630 793304 0.260 1

500 25 DDA203 AC-25/0.5 2CSB203001R4250 793403 0.220 1

40 DDA203 AC-40/0.5 2CSB203001R4400 793502 0.220 1

63 � DDA203 AC-63/0.5 2CSB203001R4630 793601 0.260 1

1000 25 DDA203 AC-25/1 2CSB203001R5250 808503 0.220 1

40 DDA203 AC-40/1 2CSB203001R5400 808602 0.220 1

63 � DDA203 AC-63/1 2CSB203001R5630 793700 0.260 1

2000 63 DDA203 AC-63/2 2CSB203001R6630 793809 0.260 1

4 30 25 DDA204 AC-25/0.03 2CSB204001R1250 793908 0.260 1

40 DDA204 AC-40/0.03 2CSB204001R1400 794004 0.260 1

63 � � DDA204 AC-63/0.03 2CSB204001R1630 794103 0.305 1

100 25 DDA204 AC-25/0.1 2CSB204001R2250 794202 0.260 1

40 DDA204 AC-40/0.1 2CSB204001R2400 794301 0.260 1

63 � DDA204 AC-63/0.1 2CSB204001R2630 794400 0.305 1

300 25 DDA204 AC-25/0.3 2CSB204001R3250 794509 0.260 1

40 DDA204 AC-40/0.3 2CSB204001R3400 794608 0.260 1

63 � DDA204 AC-63/0.3 2CSB204001R3630 794707 0.305 1

500 25 DDA204 AC-25/0.5 2CSB204001R4250 794806 0.260 1

40 DDA204 AC-40/0.5 2CSB204001R4400 794905 0.260 1

63 � DDA204 AC-63/0.5 2CSB204001R4630 795001 0.305 1

1000 25 DDA204 AC-25/1 2CSB204001R5250 808701 0.260 1

40 DDA204 AC-40/1 2CSB204001R5400 808800 0.260 1

63 � DDA204 AC-63/1 2CSB204001R5630 795100 0.305 1

2000 63 DDA204 AC-63/2 2CSB204001R6630 795209 0.305 1

� version with test button working at 110VAC - 254VAC is available. For selection tables refer to special version paragraph.� provided with additional terminals for remote tripping

1 3

2/1 4/3

5

6/5

2 4 6

In=63 AY1 Y2

2CS

C40

0163

F020

12C

SC

4001

64F0

201

2CS

C40

0165

F020

1


3/23ABB

3


Selection tablesRCD-blocks DDA 200 series A y type


DDA 200 A

A DDA 200 A typeFunction: RCD-block for assembly on site with MCBs S 200 series. Protection against the effects of sinusoidal alternating and direct pulsating earth fault currents; protection against indirect contacts and additional protection against direct (with IΔn=30 mA) contacts.




2 10 25 DDA202 A-25/0.01 2CSB202101R0250 795308 0.180 1

30 25 DDA202 A-25/0.03 2CSB202101R1250 795407 0.180 1

40 DDA202 A-40/0.03 2CSB202101R1400 795506 0.180 1

63 � DDA202 A-63/0.03 2CSB202101R1630 795605 0.180 1

100 25 DDA202 A-25/0.1 2CSB202101R2250 795704 0.180 1

40 DDA202 A-40/0.1 2CSB202101R2400 795803 0.180 1

63 � DDA202 A-63/0.1 2CSB202101R2630 795902 0.180 1

300 25 DDA202 A-25/0.3 2CSB202101R3250 796008 0.180 1

40 DDA202 A-40/0.3 2CSB202101R3400 796107 0.180 1

63 � DDA202 A-63/0.3 2CSB202101R3630 796206 0.180 1

500 25 DDA202 A-25/0.5 2CSB202101R4250 796305 0.180 1

40 DDA202 A-40/0.5 2CSB202101R4400 796404 0.180 1

63 � DDA202 A-63/0.5 2CSB202101R4630 796503 0.180 1

1000 25 DDA202 A-25/1 2CSB202101R5250 808909 0.180 1

40 DDA202 A-40/1 2CSB202101R5400 809005 0.180 1

63 � DDA202 A-63/1 2CSB202101R5630 796602 0.180 1

3 30 25 DDA203 A-25/0.03 2CSB203101R1250 796701 0.220 1

40 � DDA203 A-40/0.03 2CSB203101R1400 796800 0.220 1

63 � � DDA203 A-63/0.03 2CSB203101R1630 796909 0.260 1

100 25 DDA203 A-25/0.1 2CSB203101R2250 797005 0.220 1

40 DDA203 A-40/0.1 2CSB203101R2400 797104 0.220 1

63 � DDA203 A-63/0.1 2CSB203101R2630 797203 0.260 1

300 25 DDA203 A-25/0.3 2CSB203101R3250 797302 0.220 1

40 DDA203 A-40/0.3 2CSB203101R3400 797401 0.220 1

63 � DDA203 A-63/0.3 2CSB203101R3630 797500 0.260 1

500 25 DDA203 A-25/0.5 2CSB203101R4250 797609 0.220 1

40 DDA203 A-40/0.5 2CSB203101R4400 797708 0.220 1

63 � DDA203 A-63/0.5 2CSB203101R4630 797807 0.260 1

1000 25 DDA203 A-25/1 2CSB203101R5250 809104 0.220 1

40 DDA203 A-40/1 2CSB203101R5400 809203 0.220 1

63 � DDA203 A-63/1 2CSB203101R5630 797906 0.260 1

4 30 25 DDA204 A-25/0.03 2CSB204101R1250 798002 0.260 1

40 DDA204 A-40/0.03 2CSB204101R1400 798101 0.260 1

63 � � DDA204 A-63/0.03 2CSB204101R1630 798200 0.305 1

100 25 DDA204 A-25/0.1 2CSB204101R2250 798309 0.260 1

40 DDA204 A-40/0.1 2CSB204101R2400 798408 0.260 1

63 � DDA204 A-63/0.1 2CSB204101R2630 798507 0.305 1

300 25 DDA204 A-25/0.3 2CSB204101R3250 798606 0.260 1

40 DDA204 A-40/0.3 2CSB204101R3400 798705 0.260 1

63 � DDA204 A-63/0.3 2CSB204101R3630 798804 0.305 1

500 25 DDA204 A-25/0.5 2CSB204101R4250 798903 0.260 1

40 DDA204 A-40/0.5 2CSB204101R4400 799009 0.260 1

63 � DDA204 A-63/0.5 2CSB204101R4630 799108 0.305 1

1000 25 DDA204 A-25/1 2CSB204101R5250 809302 0.260 1

40 DDA204 A-40/1 2CSB204101R5400 809401 0.260 1

63 � DDA204 A-63/1 2CSB204101R5630 799207 0.305 1

� version with test button working at 110VAC - 254VAC is available. For selection tables refer to special version paragraph.� provided with additional terminals for remote tripping

1 3

2/1 4/3

5

6/5

2 4 6

In=63 AY1 Y2

2CS

C40

0163

F020

12C

SC

4001

64F0

201

2CS

C40

0165

F020

1


3/24 ABB

3



Selection tablesRCD-blocks DDA 200 series special version

DDA 200 @ 110 VDDA 200 @ 400 V

DDA 200 special version 110 V and 400 VFunction: special version of RCD-blocks to assembly on site with MCBs S 200 series. Special version are available with protection against the effects of sinusoidal alternating and/or direct pulsating earth fault currents, protection against indirect contacts and additional protection against direct contacts (with IΔn=30 mA).DDA200 110 V is a particular RCD-block with voltage range for test button Ut = 110-245 V. RCD- blocks work for naval applications where the IT system is typically used and the voltage between the phase and the neutral conductor is 115 - 125 V. DDA200 110 V (Ut = 110-245 V) are suitable for naval applications. Special version is also available for 400 V in the two poles version working in two-phase industrialsystems where voltage between phases is 400 V.

Applications: naval, industrial.

Standards: IEC EN 61009 Ann. G

110 V versionNumber Rated Rated Order Bbn Price Price Weight Packof poles residual current details 8012542 1 piece group 1 piece unit current IΔn mA In A Type code Order code EAN kg pc.

AC type

4 AC 63 � DDA 204 AC-63/0.03 110V 2CSB204099R1630 929901 0.350 1

A type

3 A 40 DDA 203 A-40/0.03 110V 2CSB203199R1400 811701 0.350 1

3 A 63 � DDA 203 A-63/0.03 110V 2CSB203199R1630 811800 0.350 1

4 A 63 � DDA 204 A-63/0.03 110V 2CSB204199R1630 812104 0.350 1

400 V versionNumber Rated Rated Order Bbn Price Price Weight Packof poles residual current details 8012542 1 piece group 1 piece unit current IΔn mA In A Type code Order code EAN kg pc.

A type

2 A 63 � DDA 202 A-63/0.03 400V 2CSB202192R1630 954934 0.200 1

� provided with additional terminals for remote tripping

1 3

2/1 4/3

5

6/5

2 4 6

In=63 AY1 Y2

2CS

C40

0115

F000

12C

SC

4001

16F0

001

In=40 A

2CS

C40

0562

F000

1


3/25ABB

3


A DDA 200 AP-R, A type Function: RCD-block for assembly on site with MCBs S 200 series. Protection against the effects of sinusoidal alternating and direct pulsating earth fault currents, providing the best compromise between safety and continuity in the service thanks to the resistance to unwanted trippings; protection against indirect contacts and additional protection against direct (with IΔn=30 mA) contacts.





2 30 25 DDA202 A-25/0.03 AP-R 2CSB202401R1250 801108 0.180 1

40 DDA202 A-40/0.03 AP-R 2CSB202401R1400 801207 0.180 1

63 � DDA202 A-63/0.03 AP-R 2CSB202401R1630 801306 0.180 1

3 30 25 DDA203 A-25/0.03 AP-R 2CSB203401R1250 811008 0.220 1

40 DDA203 A-40/0.03 AP-R 2CSB203401R1400 811107 0.220 1

63 � DDA203 A-63/0.03 AP-R 2CSB203401R1630 811206 0.260 1

4 30 25 DDA204 A-25/0.03 AP-R 2CSB204401R1250 801405 0.260 1

40 DDA204 A-40/0.03 AP-R 2CSB204401R1400 801504 0.260 1

63 � DDA204 A-63/0.03 AP-R 2CSB204401R1630 801603 0.305 1


1 3

2/1 4/3

5

6/5

2 4 6

In=63 AY1 Y2

2CS

C40

0163

F020

1

AC DDA 200 AP-R, AC type Function: RCD-block for assembly on site with MCBs S 200 series. Protection against the effects of sinusoidal alternating earth fault currents, providing the best compromise between safety and continuity in the service thanks to the resistance to unwanted trippings; protection against indirect contacts and additional protection against direct (with IΔn=30 mA) contacts.





2 30 25 DDA202 AC-25/0.03 AP-R 2CSB202301R1250 800507 0.180 1

40 DDA202 AC-40/0.03 AP-R 2CSB202301R1400 800606 0.180 1

63 � DDA202 AC-63/0.03 AP-R 2CSB202301R1630 800705 0.180 1

3 30 25 DDA203 AC-25/0.03 AP-R 2CSB203301R1250 810704 0.220 1

40 DDA203 AC-40/0.03 AP-R 2CSB203301R1400 810803 0.220 1

63 � DDA203 AC-63/0.03 AP-R 2CSB203301R1630 810902 0.260 1

4 30 25 DDA204 AC-25/0.03 AP-R 2CSB204301R1250 800804 0.260 1

40 DDA204 AC-40/0.03 AP-R 2CSB204301R1400 800903 0.260 1

63 � DDA204 AC-63/0.03 AP-R 2CSB204301R1630 801009 0.305 1

1 3

2/1 4/3

5

6/5

2 4 6

In=63 AY1 Y2


Selection tablesRCD-blocks DDA 200 series AC w type and A y type, AP-R (high immunity)

DDA 200 AP-R

2CS

C40

0163

F020

1


3/26 ABB

3

Technical details .......................... pag. 11/76 Overall dimensions ........................ pag. 13/7 Application sheets ......................... pag. 12/4

Selection tablesRCD-blocks DDA 200 series A y type, AE (for emergency stop)


DDA 200 AE

A DDA 200 AE, A type Function: RCD-block for assembly on site with MCBs S 200 series. Protection against the effects of sinusoidal alternating and direct pulsating earth fault currents; protection against indirect contacts and additional protection against direct (with IΔn=30 mA) contacts.The RCD-block is provided with two additional terminals to be used in emergency circuits for remote opening in positive safety. A remote control circuit should be connected to those terminals where NC push buttons should be inserted in series.ATTENTION!It’s allowed to use multiple NC buttons to control one DDA200 AE but it’s not permitted to use one button in a control circuit for more RCD-blocks DDA200 AE. DDA200 AE must be supplied by the top side.




2 30 63 DDA202 A-63/0.03 AE 2CSB202701R1630 801702 0.180 1

300 63 DDA202 A-63/0.3 AE 2CSB202701R3630 801801 0.180 1

500 63 DDA202 A-63/0.5 AE 2CSB202701R4630 801900 0.180 1

1000 63 DDA202 A-63/1 AE 2CSB202701R5630 802006 0.180 1

3 30 63 DDA203 A-63/0.03 AE 2CSB203701R1630 802105 0.260 1

300 63 DDA203 A-63/0.3 AE 2CSB203701R3630 802204 0.260 1

500 63 DDA203 A-63/0.5 AE 2CSB203701R4630 802303 0.260 1

1000 63 DDA203 A-63/1 AE 2CSB203701R5630 802402 0.260 1

4 30 63 DDA204 A-63/0.03 AE 2CSB204701R1630 802501 0.305 1

300 63 DDA204 A-63/0.3 AE 2CSB204701R3630 802600 0.305 1

500 63 DDA204 A-63/0.5 AE 2CSB204701R4630 802709 0.305 1

1000 63 DDA204 A-63/1 AE 2CSB204701R5630 802808 0.305 1

2CS

C40

0163

F020

12C

SC

4005

63F0

201

2CS

C40

0562

F020

1

Y1 Y2

2 4 6

2 4 6

1 3 5

INPUT

OUTPUT

Y1 Y2

2 4 6 N

2 4 6 N

1 3 5 N

INPUT

OUTPUT

Y1 Y2

2 4

2 4

1 3

Y1 Y2

INPUT

OUTPUT


3/27ABB

3



AC

Selection tablesRCD-blocks DDA 200 series AC w type, selective

DDA 200 AC S

DDA 200 AC selective typeFunction: RCD-block for assembly on site with MCBs S 200 series. Protection against the effects of sinusoidal alternating earth fault currents with an intentional tripping delay, which permits to realize the selectivity with downstream instantaneous devices (for more information about selectivity see the technical guide).





2 100 63 DDA202 AC S-63/0.1 2CSB202901R2630 809500 0.180 1

300 63 DDA202 AC S-63/0.3 2CSB202901R3630 809609 0.180 1

500 63 DDA202 AC S-63/0.5 2CSB202901R4630 809708 0.180 1

1000 63 DDA202 AC S-63/1 2CSB202901R5630 809807 0.180 1

3 100 63 DDA203 AC S-63/0.1 2CSB203901R2630 809906 0.260 1

300 63 DDA203 AC S-63/0.3 2CSB203901R3630 810001 0.260 1

500 63 DDA203 AC S-63/0.5 2CSB203901R4630 810100 0.260 1

1000 63 DDA203 AC S-63/1 2CSB203901R5630 810209 0.260 1

4 100 63 DDA204 AC S-63/0.1 2CSB204901R2630 810308 0.305 1

300 63 DDA204 AC S-63/0.3 2CSB204901R3630 810407 0.305 1

500 63 DDA204 AC S-63/0.5 2CSB204901R4630 810506 0.305 1

1000 63 DDA204 AC S-63/1 2CSB204901R5630 810605 0.305 1

Attention:All DDA 200 AC S are provided with additional terminals for remote tripping

1 3

2/1 4/3

5

6/5

2 4 6

In=63 AY1 Y2

2CS

C40

0163

F020

12C

SC

4005

63F0

201

2CS

C40

0562

F020

1


3/28 ABB

3



A

Selection tablesRCD-blocks DDA 200 series A y type, selective

DDA 200 A S

DDA 200 A selective typeFunction: RCD-block for assembly on site with MCBs S 200 series. Protection against the effects of sinusoidal alternating and direct pulsating earth fault currents with an intentional tripping delay, which permits to realize the selectivity with downstream instantaneous devices (for more information about selectivity see the technical guide).





2 100 63 DDA202 A S-63/0.1 2CSB202201R2630 799306 0.180 1

300 63 DDA202 A S-63/0.3 2CSB202201R3630 799405 0.180 1

500 63 DDA202 A S-63/0.5 2CSB202201R4630 799504 0.180 1

1000 63 DDA202 A S-63/1 2CSB202201R5630 799603 0.180 1

3 100 63 DDA203 A S-63/0.1 2CSB203201R2630 799702 0.260 1

300 63 DDA203 A S-63/0.3 2CSB203201R3630 799801 0.260 1

500 63 DDA203 A S-63/0.5 2CSB203201R4630 799900 0.260 1

1000 63 DDA203 A S-63/1 2CSB203201R5630 800002 0.260 1

4 100 63 DDA204 A S-63/0.1 2CSB204201R2630 800101 0.305 1

300 63 DDA204 A S-63/0.3 2CSB204201R3630 800200 0.305 1

500 63 DDA204 A S-63/0.5 2CSB204201R4630 800309 0.305 1

1000 63 DDA204 A S-63/1 2CSB204201R5630 800408 0.305 1

Attention:All DDA 200 A S are provided with additional terminals for remote tripping

1 3

2/1 4/3

5

6/5

2 4 6

In=63 AY1 Y2

2CS

C40

0163

F020

12C

SC

4005

63F0

201

2CS

C40

0562

F020

1


3/29ABB

3


2CS

C40

0125

F000

1

6/52/1 4/3 N

51 3 N

2 4 6 N

6/52/1 4/3

51 3

2 4 6

2CS

C40

0563

F000

1

2/1 4/3

1 3

2 4

2CS

C40

0563

F000

1

Selection tablesRCD-blocks DDA 200 seriesB y type


DDA 200 B

B DDA 200 type B for continuous type fault currents RCD-blocks type B are also sensitive to continuous or mainly continuous (continuous with weak ondulation) current pulsating earth fault currents. They are also sensitive to alternate sinusoidal and direct pulsating earth fault currents as with type A circuit breakers.They satisfy the requirements of type A devices and thus the requirements for type AC devices which can be considered an extension. For this reason the differential blocks type B are sometimes referred as “universal type”, as sensitive to “all” kind of residual current shape.DDA 200 type B can be coupled with all the S 200 series MCBs.They are used for protection in installations with electronic equipments according to EN 50178.

Applications: tertiary and industrial.

Standards: IEC EN 61009 Ann. G, IEC 60755

Surge current resistance (8/20 wave): 3000 A



2 30 63 DDA202 B-63/0.03 2CSB202501R1630 987802 0.260 1

300 63 DDA202 B-63/0.3 2CSB202501R3630 987703 0.260 1

3 30 63 DDA203 B-63/0.03 2CSB203501R1630 154754 0.325 1

300 63 DDA203 B-63/0.3 2CSB203501R3630 154853 0.325 1

4 30 63 DDA204 B-63/0.03 2CSB204501R1630 987505 0.325 1

300 63 DDA204 B-63/0.3 2CSB204501R3630 987604 0.325 1

DDA 200 type B for selective continuous type fault currents Function: protection against the effects of alternate sinusoidal, direct pulsating, continuous current and continuous current pulsating earth fault currents with an intentional trip delay that permits se-lectivity with instantaneous type devices placed downstream (for further information on selectivity, see chapter 10).DDA 200 type B can be coupled with all the S 200 series MCBs.

They are used for protection in installations with electronic equipments according to EN 50178.

Applications: tertiary and industrial.

Standards: IEC EN 61009 Ann. G, IEC 60755

Surge current resistance (8/20 wave): 5000 A



3 300 63 DDA203 B S-63/0.3 2CSB203801R3630 987901 0.325 1

4 300 63 DDA204 B S-63/0.3 2CSB204801R3630 154952 0.325 1

B

2CS

C40

0125

F000

1

6/52/1 4/3 N

51 3 N

2 4 6 N

6/52/1 4/3

51 3

2 4 6

2CS

C40

0563

F000

1


3/30 ABB

3

Technical featuresRCBOs DS201 series

DS201System pro M compact®

TECHNICAL CHARACTERISTICSStandards


Rated current In ARated sensitivity IΔn ARated voltage Ue VInsulation voltage Ui VMax. operating voltage of circuit test VMin. operating voltage of circuit test VRated frequency HzRated breaking capacity acc. to IEC/EN 61009 ultimate Icn ARated breaking capacity acc. to IEC/EN 60947-2 ultimate Icu kA1P+N @230 VAC service Ics kARated residual breaking capacity IΔm kARated impulse withstand voltage (1.2/50) Uimp kVDielectric test voltage at ind. freq. for 1 min. kVThermomagnetic release B: 3 In ≤ Im ≤ 5 Incharacteristic C: 5 In ≤ Im ≤ 10 In

K: 10 In ≤ Im ≤ 14 InSurge current resistance (wave 8/20) A

Mechanical Togglefeatures Flag indicators


terminalsTropicalization constant climatic conditions °C/RHacc. to IEC /EN 60068-2 variable climatic conditions °C/RHReference temperature for setting of thermal element °CAmbient temperature (with daily average ≤ +35 °C) °CStorage temperature °C

Installation Terminal type topbottom

Terminal size top/bottom for cables mm2

Terminal size top/bottom for busbar mm2

Tightening torque top/bottom N*mMountingConnection

Dimensions Dimensions (H x D x W) mmand weight Weight gCombination Combinable with: auxiliary contactwith auxiliary signal contactelements shunt trip

undervoltage release


3/31ABB

3



DS201 L DS201 DS201 MIEC / EN 61009

AC A APR AC A APR AC A APR1P+N

6 ≤ In ≤ 32 1 ≤ In ≤ 40 4 ≤ In ≤ 400.03-0.3 0.01-0.03-0.3 0.03 0.03-0.1-0.3-1 0.01-0.03-0.1-0.3 0.03-0.1-0.3 0.03-0.1-0.3 0.01-0.03-0.1-0.3 0.03-0.1-0.3

230-240500254110

50…604500 6000 10000

6 10 104.5 6 7.54.5 6 6

42.5

250 (3000 for APR versions)black sealable in ON-OFF position

differential trip indicator (blue)contact position indicator (green/red)

1000020000IP4XIP2X

23/83 - 40/93 - 55/2025/95 - 40/95

30-25…+55-40…+70

failsafe bi-directional cylinder-lift terminal at top and bottom (shock protected)failsafe bi-directional cylinder-lift terminal at top and bottom (shock protected)

25/2510/10


from top and bottom85 x 69 x 35

239yesyesyesyes


3/32 ABB

3


DS201 L A type, C characteristicFunction: protection of end user single-phase circuits against overload and short-circuit currents; protection against the effects of sinusoidal alternating earth fault currents; protection against indirect contact and additional protection against direct contact (IΔn=30 mA).



Icn=4.5 kA


1+N 10 6 DS201 L C6 A10 2CSR245140R0064 163404 0.240 5

10 DS201 L C10 A10 2CSR245140R0104 171003 0.240 5

16 DS201 L C16 A10 2CSR245140R0164 171102 0.240 5

30 6 DS201 L C6 A30 2CSR245140R1064 172406 0.240 5

10 DS201 L C10 A30 2CSR245140R1104 172505 0.240 5

16 DS201 L C16 A30 2CSR245140R1164 172604 0.240 5

20 DS201 L C20 A30 2CSR245140R1204 172703 0.240 5

25 DS201 L C25 A30 2CSR245140R1254 173809 0.240 5

32 DS201 L C32 A30 2CSR245140R1324 173908 0.240 5

300 6 DS201 L C6 A300 2CSR245140R3064 174004 0.240 5

10 DS201 L C10 A300 2CSR245140R3104 174103 0.240 5

16 DS201 L C16 A300 2CSR245140R3164 174202 0.240 5

20 DS201 L C20 A300 2CSR245140R3204 174301 0.240 5

25 DS201 L C25 A300 2CSR245140R3254 174707 0.240 5

32 DS201 L C32 A300 2CSR245140R3324 174806 0.240 5

C

DS201 L AC type, C characteristicFunction: protection of end user single-phase circuits against overload and short-circuit currents; protection against the effects of sinusoidal alternating earth fault currents; protection against indirect contact and additional protection against direct contact (IΔn=30 mA).



Icn=4.5 kA


1+N 30 6 DS201 L C6 AC30 2CSR245040R1064 171201 0.240 5

10 DS201 L C10 AC30 2CSR245040R1104 171300 0.240 5

16 DS201 L C16 AC30 2CSR245040R1164 171409 0.240 5

20 DS201 L C20 AC30 2CSR245040R1204 171508 0.240 5

25 DS201 L C25 AC30 2CSR245040R1254 171607 0.240 5

32 DS201 L C32 AC30 2CSR245040R1324 171706 0.240 5

300 6 DS201 L C6 AC300 2CSR245040R3064 171805 0.240 5

10 DS201 L C10 AC300 2CSR245040R3104 171904 0.240 5

16 DS201 L C16 AC300 2CSR245040R3164 172000 0.240 5

20 DS201 L C20 AC300 2CSR245040R3204 172109 0.240 5

25 DS201 L C25 AC300 2CSR245040R3254 172208 0.240 5

32 DS201 L C32 AC300 2CSR245040R3324 172307 0.240 5

C

Selection tablesRCBOs DS201 series 4500 AC w type, A y type

DS201 LSystem pro M compact®

2CS

C40

0005

F020

22C

SC

4000

05F0

202


3/33ABB

3


DS201 L APR type, C characteristicFunction: protection against the effects of sinusoidal alternating earth fault currents, providing an optimal trade-off between safety and continuity of service, thanks to the resistance to unwanted tripping; protection against indirect contact and additional protection against direct (IΔn=30mA) contact; protection and isolation of resistive and inductive loads.



Icn=4.5 kA


1+N 30 6 DS201 L C6 APR30 2CSR245440R1064 174905 0.240 5

10 DS201 L C10 APR30 2CSR245440R1104 175001 0.240 5

16 DS201 L C16 APR30 2CSR245440R1164 175100 0.240 5

20 DS201 L C20 APR30 2CSR245440R1204 175209 0.240 5

25 DS201 L C25 APR30 2CSR245440R1254 175605 0.240 5

32 DS201 L C32 APR30 2CSR245440R1324 175704 0.240 5

C

Selection tablesRCBOs DS201 series 4500 A y APR type

DS201 LSystem pro M compact®

2CS

C40

0005

F020

2


3/34 ABB

3


DS201 AC type, C characteristicFunction: protection of end user single-phase circuits against overload and short-circuit currents; protection against the effects of sinusoidal alternating earth fault currents; protection against indirect contact and additional protection against direct contact (IΔn=30 mA).



Icn=6 kA


1+N 30 6 DS201 C6 AC30 2CSR255040R1064 294504 0.240 5

10 DS201 C10 AC30 2CSR255040R1104 294603 0.240 5

13 DS201 C13 AC30 2CSR255040R1134 294702 0.240 5

16 DS201 C16 AC30 2CSR255040R1164 294801 0.240 5

20 DS201 C20 AC30 2CSR255040R1204 294900 0.240 5

25 DS201 C25 AC30 2CSR255040R1254 295006 0.240 5

32 DS201 C32 AC30 2CSR255040R1324 296003 0.240 5

40 DS201 C40 AC30 2CSR255040R1404 296102 0.240 5

C

DS201 AC type, B characteristicFunction: protection of end user single-phase circuits against overload and short-circuit currents; protection against the effects of sinusoidal alternating and direct pulsating earth fault currents; pro-tection against indirect contact and additional protection against direct contact (IΔn=30 mA).



Icn=6 kA


1+N 30 6 DS201 B6 AC30 2CSR255040R1065 279709 0.240 5

10 DS201 B10 AC30 2CSR255040R1105 280309 0.240 5

13 DS201 B13 AC30 2CSR255040R1135 285205 0.240 5

16 DS201 B16 AC30 2CSR255040R1165 285304 0.240 5

20 DS201 B20 AC30 2CSR255040R1205 285403 0.240 5

25 DS201 B25 AC30 2CSR255040R1255 285502 0.240 5

32 DS201 B32 AC30 2CSR255040R1325 285601 0.240 5

40 DS201 B40 AC30 2CSR255040R1405 285700 0.240 5

100 6 DS201 B6 AC100 2CSR255040R2065 285809 0.240 5

10 DS201 B10 AC100 2CSR255040R2105 285908 0.240 5

13 DS201 B13 AC100 2CSR255040R2135 286004 0.240 5

16 DS201 B16 AC100 2CSR255040R2165 286103 0.240 5

20 DS201 B20 AC100 2CSR255040R2205 286202 0.240 5

25 DS201 B25 AC100 2CSR255040R2255 286301 0.240 5

32 DS201 B32 AC100 2CSR255040R2325 286400 0.240 5

40 DS201 B40 AC100 2CSR255040R2405 286509 0.240 5

300 6 DS201 B6 AC300 2CSR255040R3065 286608 0.240 5

10 DS201 B10 AC300 2CSR255040R3105 286707 0.240 5

13 DS201 B13 AC300 2CSR255040R3135 293903 0.240 5

16 DS201 B16 AC300 2CSR255040R3165 294009 0.240 5

20 DS201 B20 AC300 2CSR255040R3205 294108 0.240 5

25 DS201 B25 AC300 2CSR255040R3255 294207 0.240 5

32 DS201 B32 AC300 2CSR255040R3325 294306 0.240 5

40 DS201 B40 AC300 2CSR255040R3405 294405 0.240 5

B

Selection tablesRCBOs DS201 series 6000 AC w type, APR type


2CS

C40

0005

F020

22C

SC

4000

05F0

202


3/35ABB

3


100 6 DS201 C6 AC100 2CSR255040R2064 296201 0.240 5

10 DS201 C10 AC100 2CSR255040R2104 296409 0.240 5

13 DS201 C13 AC100 2CSR255040R2134 370802 0.240 5

16 DS201 C16 AC100 2CSR255040R2164 370901 0.240 5

20 DS201 C20 AC100 2CSR255040R2204 371601 0.240 5

25 DS201 C25 AC100 2CSR255040R2254 371700 0.240 5

32 DS201 C32 AC100 2CSR255040R2324 371809 0.240 5

40 DS201 C40 AC100 2CSR255040R2404 498100 0.240 5

300 6 DS201 C6 AC300 2CSR255040R3064 498209 0.240 5

10 DS201 C10 AC300 2CSR255040R3104 498308 0.240 5

13 DS201 C13 AC300 2CSR255040R3134 505907 0.240 5

16 DS201 C16 AC300 2CSR255040R3164 506003 0.240 5

20 DS201 C20 AC300 2CSR255040R3204 506102 0.240 5

25 DS201 C25 AC300 2CSR255040R3254 506201 0.240 5

32 DS201 C32 AC300 2CSR255040R3324 618300 0.240 5

40 DS201 C40 AC300 2CSR255040R3404 638407 0.240 5

1000 6 DS201 C6 AC1000 2CSR255040R5064 996606 0.240 5

10 DS201 C10 AC1000 2CSR255040R5104 996705 0.240 5

16 DS201 C16 AC1000 2CSR255040R5164 996804 0.240 5

20 DS201 C20 AC1000 2CSR255040R5204 996903 0.240 5

25 DS201 C25 AC1000 2CSR255040R5254 997009 0.240 5

32 DS201 C32 AC1000 2CSR255040R5324 997108 0.240 5

40 DS201 C40 AC1000 2CSR255040R5404 997207 0.240 5

DS201 APR type, C characteristicFunction: protection against the effects of sinusoidal alternating earth fault currents, providing an optimal trade-off between safety and continuity of service thanks to the resistance to unwanted tripping; protection against indirect contact and additional protection against direct (IΔn=30 mA) contact; protection and isolation of resistive and inductive loads.



Icn=6 kA


1+N 30 6 DS201 C6 APR30 2CSR255440R1064 997306 0.240 5

10 DS201 C10 APR30 2CSR255440R1104 997405 0.240 5

13 DS201 C13 APR30 2CSR255440R1134 997504 0.240 5

16 DS201 C16 APR30 2CSR255440R1164 997603 0.240 5

20 DS201 C20 APR30 2CSR255440R1204 997702 0.240 5

25 DS201 C25 APR30 2CSR255440R1254 997801 0.240 5

32 DS201 C32 APR30 2CSR255440R1324 997900 0.240 5

40 DS201 C40 APR30 2CSR255440R1404 998006 0.240 5

100 6 DS201 C6 APR100 2CSR255440R2064 126454 0.240 5

10 DS201 C10 APR100 2CSR255440R2104 126553 0.240 5

13 DS201 C13 APR100 2CSR255440R2134 126652 0.240 5

16 DS201 C16 APR100 2CSR255440R2164 126751 0.240 5

20 DS201 C20 APR100 2CSR255440R2204 126850 0.240 5

25 DS201 C25 APR100 2CSR255440R2254 126959 0.240 5

32 DS201 C32 APR100 2CSR255440R2324 127055 0.240 5

40 DS201 C40 APR100 2CSR255440R2404 127154 0.240 5

300 6 DS201 C6 APR300 2CSR255440R3064 998105 0.240 5

10 DS201 C10 APR300 2CSR255440R3104 998204 0.240 5

13 DS201 C13 APR300 2CSR255440R3134 998303 0.240 5

16 DS201 C16 APR300 2CSR255440R3164 998402 0.240 5

20 DS201 C20 APR300 2CSR255440R3204 998501 0.240 5

25 DS201 C25 APR300 2CSR255440R3254 998600 0.240 5

32 DS201 C32 APR300 2CSR255440R3324 998709 0.240 5

40 DS201 C40 APR300 2CSR255440R3404 998808 0.240 5

C

Selection tablesRCBOs DS201 series 6000 AC w type, APR type


2CS

C40

0005

F020

2


3/36 ABB

3


C

DS201 A type, B characteristicFunction: protection of end user single-phase circuits against overload and short-circuit currents; protection against the effects of sinusoidal alternating and direct pulsating earth fault currents; pro-tection against indirect contact and additional protection against direct contact (IΔn=30 mA).



Icn=6 kA


1+N 10 10 DS201 B10 A10 2CSR255140R0105 995708 0.240 5

13 DS201 B13 A10 2CSR255140R0135 995807 0.240 5

16 DS201 B16 A10 2CSR255140R0165 995906 0.240 5

30 6 DS201 B6 A30 2CSR255140R1065 638506 0.240 5

10 DS201 B10 A30 2CSR255140R1105 647805 0.240 5

13 DS201 B13 A30 2CSR255140R1135 655503 0.240 5

16 DS201 B16 A30 2CSR255140R1165 655602 0.240 5

20 DS201 B20 A30 2CSR255140R1205 655701 0.240 5

25 DS201 B25 A30 2CSR255140R1255 766902 0.240 5

32 DS201 B32 A30 2CSR255140R1325 814504 0.240 5

40 DS201 B40 A30 2CSR255140R1405 910602 0.240 5

100 6 DS201 B6 A100 2CSR255140R2065 990307 0.240 5

10 DS201 B10 A100 2CSR255140R2105 990406 0.240 5

13 DS201 B13 A100 2CSR255140R2135 990505 0.240 5

16 DS201 B16 A100 2CSR255140R2165 990604 0.240 5

20 DS201 B20 A100 2CSR255140R2205 990703 0.240 5

25 DS201 B25 A100 2CSR255140R2255 990802 0.240 5

32 DS201 B32 A100 2CSR255140R2325 990901 0.240 5

40 DS201 B40 A100 2CSR255140R2405 991007 0.240 5

300 6 DS201 B6 A300 2CSR255140R3065 991908 0.240 5

10 DS201 B10 A300 2CSR255140R3105 992004 0.240 5

13 DS201 B13 A300 2CSR255140R3135 992103 0.240 5

16 DS201 B16 A300 2CSR255140R3165 992202 0.240 5

20 DS201 B20 A300 2CSR255140R3205 992301 0.240 5

25 DS201 B25 A300 2CSR255140R3255 992400 0.240 5

32 DS201 B32 A300 2CSR255140R3325 992509 0.240 5

40 DS201 B40 A300 2CSR255140R3405 992608 0.240 5

B

Selection tablesRCBOs DS201 series 6000 A y type

DS201

DS201 A type, C characteristicFunction: protection of end user single-phase circuits against overload and short-circuit currents; protection against the effects of sinusoidal alternating and direct pulsating earth fault currents; pro-tection against indirect contact and additional protection against direct contact (IΔn=30 mA).



Icn=6 kA


1+N 10 10 DS201 C10 A10 2CSR255140R0104 996002 0.240 5

13 DS201 C13 A10 2CSR255140R0134 996101 0.240 5

16 DS201 C16 A10 2CSR255140R0164 996200 0.240 5

30 2 DS201 C2 A30 2CSR255140R1024 123958 0.240 5

4 DS201 C4 A30 2CSR255140R1044 942306 0.240 5

6 DS201 C6 A30 2CSR255140R1064 942405 0.240 5

8 DS201 C8 A30 2CSR255140R1084 124054 0.240 5

10 DS201 C10 A30 2CSR255140R1104 952503 0.240 5

13 DS201 C13 A30 2CSR255140R1134 976004 0.240 5

16 DS201 C16 A30 2CSR255140R1164 976103 0.240 5


2CS

C40

0005

F020

22C

SC

4000

05F0

202


3/37ABB

3


20 DS201 C20 A30 2CSR255140R1204 976202 0.240 5

25 DS201 C25 A30 2CSR255140R1254 976301 0.240 5

32 DS201 C32 A30 2CSR255140R1324 990109 0.240 5

40 DS201 C40 A30 2CSR255140R1404 990208 0.240 5

100 6 DS201 C6 A100 2CSR255140R2064 991106 0.240 5

10 DS201 C10 A100 2CSR255140R2104 991205 0.240 5

13 DS201 C13 A100 2CSR255140R2134 991304 0.240 5

16 DS201 C16 A100 2CSR255140R2164 991403 0.240 5

20 DS201 C20 A100 2CSR255140R2204 991502 0.240 5

25 DS201 C25 A100 2CSR255140R2254 991601 0.240 5

32 DS201 C32 A100 2CSR255140R2324 991700 0.240 5

40 DS201 C40 A100 2CSR255140R2404 991809 0.240 5

300 2 DS201 C2 A300 2CSR255140R3024 124153 0.240 5

4 DS201 C4 A300 2CSR255140R3044 124252 0.240 5

6 DS201 C6 A300 2CSR255140R3064 992707 0.240 5

8 DS201 C8 A300 2CSR255140R3084 124351 0.240 5

10 DS201 C10 A300 2CSR255140R3104 992806 0.240 5

13 DS201 C13 A300 2CSR255140R3134 992905 0.240 5

16 DS201 C16 A300 2CSR255140R3164 993001 0.240 5

20 DS201 C20 A300 2CSR255140R3204 993100 0.240 5

25 DS201 C25 A300 2CSR255140R3254 993209 0.240 5

32 DS201 C32 A300 2CSR255140R3324 993308 0.240 5

40 DS201 C40 A300 2CSR255140R3404 993407 0.240 5

DS201 A type, K characteristicFunction: protection of end user single-phase circuits against overload and short-circuit currents; protection against the effects of sinusoidal alternating earth fault currents; protection against indirect contact and additional protection against direct contact (IΔn=30 mA).


Standard: IEC/EN 60947-2

Icn=6 kA


1+N 10 10 DS201 K10 A10 2CSR255140R0107 996309 0.240 5

13 DS201 K13 A10 2CSR255140R0137 996408 0.240 5

16 DS201 K16 A10 2CSR255140R0167 996507 0.240 5

30 1 DS201 K1 A30 2CSR255140R1017 993506 0.240 5

2 DS201 K2 A30 2CSR255140R1027 993605 0.240 5

4 DS201 K4 A30 2CSR255140R1047 993704 0.240 5

6 DS201 K6 A30 2CSR255140R1067 993803 0.240 5

8 DS201 K8 A30 2CSR255140R1087 123750 0.240 5

10 DS201 K10 A30 2CSR255140R1107 993902 0.240 5

13 DS201 K13 A30 2CSR255140R1137 994008 0.240 5

16 DS201 K16 A30 2CSR255140R1167 994107 0.240 5

20 DS201 K20 A30 2CSR255140R1207 994206 0.240 5

25 DS201 K25 A30 2CSR255140R1257 994305 0.240 5

32 DS201 K32 A30 2CSR255140R1327 994404 0.240 5

40 DS201 K40 A30 2CSR255140R1407 994503 0.240 5

300 1 DS201 K1 A300 2CSR255140R3017 994602 0.240 5

2 DS201 K2 A300 2CSR255140R3027 994701 0.240 5

4 DS201 K4 A300 2CSR255140R3047 994800 0.240 5

6 DS201 K6 A300 2CSR255140R3067 994909 0.240 5

8 DS201 K8 A300 2CSR255140R3087 123859 0.240 5

10 DS201 K10 A300 2CSR255140R3107 995005 0.240 5

13 DS201 K13 A300 2CSR255140R3137 995104 0.240 5

16 DS201 K16 A300 2CSR255140R3167 995203 0.240 5

20 DS201 K20 A300 2CSR255140R3207 995302 0.240 5

25 DS201 K25 A300 2CSR255140R3257 995401 0.240 5

32 DS201 K32 A300 2CSR255140R3327 995500 0.240 5

40 DS201 K40 A300 2CSR255140R3407 995609 0.240 5

C



2CS

C40

0005

F020

2


3/38 ABB

3


C

DS201 M AC type, B characteristicFunction: protection of end user single-phase circuits against overload and short-circuit currents; protection against the effects of sinusoidal alternating earth fault currents; protection against indirect contact and additional protection against direct contact (IΔn=30 mA).



Icn=10 kA


1+N 30 6 DS201 M B6 AC30 2CSR275040R1065 998907 0.240 5

10 DS201 M B10 AC30 2CSR275040R1105 999003 0.240 5

13 DS201 M B13 AC30 2CSR275040R1135 999102 0.240 5

16 DS201 M B16 AC30 2CSR275040R1165 999201 0.240 5

20 DS201 M B20 AC30 2CSR275040R1205 999300 0.240 5

25 DS201 M B25 AC30 2CSR275040R1255 999409 0.240 5

32 DS201 M B32 AC30 2CSR275040R1325 999508 0.240 5

40 DS201 M B40 AC30 2CSR275040R1405 999607 0.240 5

100 6 DS201 M B6 AC100 2CSR275040R2065 106159 0.240 5

10 DS201 M B10 AC100 2CSR275040R2105 106258 0.240 5

13 DS201 M B13 AC100 2CSR275040R2135 106357 0.240 5

16 DS201 M B16 AC100 2CSR275040R2165 106456 0.240 5

20 DS201 M B20 AC100 2CSR275040R2205 106555 0.240 5

25 DS201 M B25 AC100 2CSR275040R2255 106654 0.240 5

32 DS201 M B32 AC100 2CSR275040R2325 106753 0.240 5

40 DS201 M B40 AC100 2CSR275040R2405 106852 0.240 5

300 6 DS201 M B6 AC300 2CSR275040R3065 107750 0.240 5

10 DS201 M B10 AC300 2CSR275040R3105 107859 0.240 5

13 DS201 M B13 AC300 2CSR275040R3135 107958 0.240 5

16 DS201 M B16 AC300 2CSR275040R3165 108054 0.240 5

20 DS201 M B20 AC300 2CSR275040R3205 108153 0.240 5

25 DS201 M B25 AC300 2CSR275040R3255 108252 0.240 5

32 DS201 M B32 AC300 2CSR275040R3325 108351 0.240 5

40 DS201 M B40 AC300 2CSR275040R3405 108450 0.240 5

B

Selection tablesRCBOs DS201 series 10000 AC w type, A y APR type

DS201 M

DS201 M AC type, C characteristicFunction: protection of end user single-phase circuits against overload and short-circuit currents;protection against the effects of sinusoidal alternating earth fault currents; protection against indirect contact and additional protection against direct contact (IΔn=30 mA).



Icn=10 kA


1+N 30 6 DS201 M C6 AC30 2CSR275040R1064 999706 0.240 5

10 DS201 M C10 AC30 2CSR275040R1104 999805 0.240 5

13 DS201 M C13 AC30 2CSR275040R1134 999904 0.240 5

16 DS201 M C16 AC30 2CSR275040R1164 105657 0.240 5

20 DS201 M C20 AC30 2CSR275040R1204 105756 0.240 5

25 DS201 M C25 AC30 2CSR275040R1254 105855 0.240 5

32 DS201 M C32 AC30 2CSR275040R1324 105954 0.240 5

40 DS201 M C40 AC30 2CSR275040R1404 106050 0.240 5


2CS

C40

0005

F020

22C

SC

4000

05F0

202


3/39ABB

3


100 6 DS201 M C6 AC100 2CSR275040R2064 106951 0.240 5

10 DS201 M C10 AC100 2CSR275040R2104 107057 0.240 5

13 DS201 M C13 AC100 2CSR275040R2134 107156 0.240 5

16 DS201 M C16 AC100 2CSR275040R2164 107255 0.240 5

20 DS201 M C20 AC100 2CSR275040R2204 107354 0.240 5

25 DS201 M C25 AC100 2CSR275040R2254 107453 0.240 5

32 DS201 M C32 AC100 2CSR275040R2324 107552 0.240 5

40 DS201 M C40 AC100 2CSR275040R2404 107651 0.240 5

300 6 DS201 M C6 AC300 2CSR275040R3064 108559 0.240 5

10 DS201 M C10 AC300 2CSR275040R3104 108658 0.240 5

13 DS201 M C13 AC300 2CSR275040R3134 108757 0.240 5

16 DS201 M C16 AC300 2CSR275040R3164 108856 0.240 5

20 DS201 M C20 AC300 2CSR275040R3204 108955 0.240 5

25 DS201 M C25 AC300 2CSR275040R3254 109051 0.240 5

32 DS201 M C32 AC300 2CSR275040R3324 109150 0.240 5

40 DS201 M C40 AC300 2CSR275040R3404 109259 0.240 5

DS201 M APR type, C characteristicFunction: protection against the effects of sinusoidal alternating earth fault currents, providing an optimal compromise between safety and continuity of service, thanks to the resistance to unwanted tripping; protection against indirect contact and additional protection against direct (IΔn=30 mA) contact; protection and isolation of resistive and inductive loads.



Icn=10 kA


1+N 30 6 DS201 M C6 APR30 2CSR275440R1064 114154 0.240 5

10 DS201 M C10 APR30 2CSR275440R1104 114253 0.240 5

13 DS201 M C13 APR30 2CSR275440R1134 114352 0.240 5

16 DS201 M C16 APR30 2CSR275440R1164 114451 0.240 5

20 DS201 M C20 APR30 2CSR275440R1204 114550 0.240 5

25 DS201 M C25 APR30 2CSR275440R1254 114659 0.240 5

32 DS201 M C32 APR30 2CSR275440R1324 114758 0.240 5

40 DS201 M C40 APR30 2CSR275440R1404 114857 0.240 5

100 6 DS201 M C6 APR100 2CSR275440R2064 127253 0.240 5

10 DS201 M C10 APR100 2CSR275440R2104 127352 0.240 5

13 DS201 M C13 APR100 2CSR275440R2134 127451 0.240 5

16 DS201 M C16 APR100 2CSR275440R2164 127550 0.240 5

20 DS201 M C20 APR100 2CSR275440R2204 127659 0.240 5

25 DS201 M C25 APR100 2CSR275440R2254 127758 0.240 5

32 DS201 M C32 APR100 2CSR275440R2324 127857 0.240 5

40 DS201 M C40 APR100 2CSR275440R2404 127956 0.240 5

300 6 DS201 M C6 APR300 2CSR275440R3064 114956 0.240 5

10 DS201 M C10 APR300 2CSR275440R3104 115052 0.240 5

13 DS201 M C13 APR300 2CSR275440R3134 115151 0.240 5

16 DS201 M C16 APR300 2CSR275440R3164 115250 0.240 5

20 DS201 M C20 APR300 2CSR275440R3204 115359 0.240 5

25 DS201 M C25 APR300 2CSR275440R3254 115458 0.240 5

32 DS201 M C32 APR300 2CSR275440R3324 115557 0.240 5

40 DS201 M C40 APR300 2CSR275440R3404 115656 0.240 5

C

Selection tablesRCBOs DS201 series 10000 AC w type, A y APR type

DS201 MSystem pro M compact®

2CS

C40

0005

F020

2


3/40 ABB

3


DS201 M A type, B characteristicFunction: protection of end user single-phase circuits against overload and short-circuit currents; protection against the effects of sinusoidal alternating and direct pulsating earth fault currents; pro-tection against indirect contact and additional protection against direct contact (IΔn=30 mA).



Icn=10 kA


1+N 10 10 DS201 M B10 A10 2CSR275140R0105 124450 0.240 5

16 DS201 M B16 A10 2CSR275140R0165 124559 0.240 5

30 6 DS201 M B6 A30 2CSR275140R1065 109358 0.240 5

10 DS201 M B10 A30 2CSR275140R1105 109457 0.240 5

13 DS201 M B13 A30 2CSR275140R1135 109556 0.240 5

16 DS201 M B16 A30 2CSR275140R1165 109655 0.240 5

20 DS201 M B20 A30 2CSR275140R1205 109754 0.240 5

25 DS201 M B25 A30 2CSR275140R1255 109853 0.240 5

32 DS201 M B32 A30 2CSR275140R1325 109952 0.240 5

40 DS201 M B40 A30 2CSR275140R1405 110057 0.240 5

100 6 DS201 M B6 A100 2CSR275140R2065 111054 0.240 5

10 DS201 M B10 A100 2CSR275140R2105 111153 0.240 5

13 DS201 M B13 A100 2CSR275140R2135 111252 0.240 5

16 DS201 M B16 A100 2CSR275140R2165 111351 0.240 5

20 DS201 M B20 A100 2CSR275140R2205 111450 0.240 5

25 DS201 M B25 A100 2CSR275140R2255 111559 0.240 5

32 DS201 M B32 A100 2CSR275140R2325 111658 0.240 5

40 DS201 M B40 A100 2CSR275140R2405 111757 0.240 5

300 6 DS201 M B6 A300 2CSR275140R3065 112556 0.240 5

10 DS201 M B10 A300 2CSR275140R3105 112655 0.240 5

13 DS201 M B13 A300 2CSR275140R3135 112754 0.240 5

16 DS201 M B16 A300 2CSR275140R3165 112853 0.240 5

20 DS201 M B20 A300 2CSR275140R3205 112952 0.240 5

25 DS201 M B25 A300 2CSR275140R3255 113058 0.240 5

32 DS201 M B32 A300 2CSR275140R3325 113157 0.240 5

40 DS201 M B40 A300 2CSR275140R3405 113256 0.240 5

B



2CS

C40

0005

F020

2


3/41ABB

3


DS201 M A type, C characteristicFunction: protection of end user single-phase circuits against overload and short-circuit currents; protection against the effects of sinusoidal alternating and direct pulsating earth fault currents; pro-tection against indirect contact and additional protection against direct contact (IΔn=30 mA).



Icn=10 kA


1+N 10 10 DS201 M C10 A10 2CSR275140R0104 124658 0.240 5

16 DS201 M C16 A10 2CSR275140R0164 124757 0.240 5

30 4 DS201 M C4 A30 2CSR275140R1044 110156 0.240 5

6 DS201 M C6 A30 2CSR275140R1064 110255 0.240 5

10 DS201 M C10 A30 2CSR275140R1104 110354 0.240 5

13 DS201 M C13 A30 2CSR275140R1134 110453 0.240 5

16 DS201 M C16 A30 2CSR275140R1164 110552 0.240 5

20 DS201 M C20 A30 2CSR275140R1204 110651 0.240 5

25 DS201 M C25 A30 2CSR275140R1254 110750 0.240 5

32 DS201 M C32 A30 2CSR275140R1324 110859 0.240 5

40 DS201 M C40 A30 2CSR275140R1404 110958 0.240 5

100 6 DS201 M C6 A100 2CSR275140R2064 111856 0.240 5

10 DS201 M C10 A100 2CSR275140R2104 111955 0.240 5

16 DS201 M C16 A100 2CSR275140R2164 112051 0.240 5

20 DS201 M C20 A100 2CSR275140R2204 112150 0.240 5

25 DS201 M C25 A100 2CSR275140R2254 112259 0.240 5

32 DS201 M C32 A100 2CSR275140R2324 112358 0.240 5

40 DS201 M C40 A100 2CSR275140R2404 112457 0.240 5

300 6 DS201 M C6 A300 2CSR275140R3064 113355 0.240 5

10 DS201 M C10 A300 2CSR275140R3104 113454 0.240 5

13 DS201 M C13 A300 2CSR275140R3134 113553 0.240 5

16 DS201 M C16 A300 2CSR275140R3164 113652 0.240 5

20 DS201 M C20 A300 2CSR275140R3204 113751 0.240 5

25 DS201 M C25 A300 2CSR275140R3254 113850 0.240 5

32 DS201 M C32 A300 2CSR275140R3324 113959 0.240 5

40 DS201 M C40 A300 2CSR275140R3404 114055 0.240 5

C



2CS

C40

0005

F020

2


3/42 ABB

3

Technical featuresRCBOs DS202C series

DS202C

TECHNICAL CHARACTERISTICSStandards


Rated current In ARated sensitivity IΔn ARated voltage Ue VInsulation voltage Ui VMax. operating voltage of circuit test VMin. operating voltage of circuit test VRated frequency HzRated breaking capacity acc. to IEC/EN 61009 ultimate Icn ARated breaking capacity acc. to IEC/EN 60947-2 ultimate Icu kA2P @230 VAC service Ics kARated residual breaking capacity IΔm kARated impulse withstand voltage (1.2/50) Uimp kVDielectric test voltage at ind. freq. for 1 min. kVThermomagnetic release B: 3 In ≤ Im ≤ 5 Incharacteristic C: 5 In ≤ Im ≤ 10 In


Mechanical Togglefeatures Flag indicators


terminalsTropicalization constant climatic conditions °C/RHacc. to IEC /EN 60068-2 variable climatic conditions °C/RHReference temperature for setting of thermal element °CAmbient temperature (with daily average ≤ +35 °C) °CStorage temperature °C


Terminal size top/bottom for cables mm2

Terminal size top/bottom for busabar mm2

Tightening torque top/bottom N*mMountingConnection

Dimensions Dimensions (H x D x W) mmand weight Weight gCombination Combinable with: auxiliary contactwith auxiliary signal contactelements shunt trip




3/43ABB

3

Technical featuresRCBOs DS202C series

DS202C

DS202C DS202C MIEC / EN 61009

A A APR2P

6 ≤ In ≤ 320.03-0.3 0.01-0.03-0.3 0.03-0.3

230-240500254110

50…606000 1000010 106 7.56 6

42.5

250 (3000 for APR versions)black sealable in ON-OFF position

differential trip indicator (blue)contact position indicator (green/red)

1000020000IP4XIP2X

23/83 - 40/93 - 55/2025/95 - 40/95

30-25…+55-40…+70

failsafe bi-directional cylinder-lift terminal at top and bottom (shock protected) failsafe bi-directional cylinder-lift terminal at top and bottom (shock protected)

25/2510/10


from top and bottom85 x 69 x 35

239yesyesyesyes



3/44 ABB

3


DS202C A type, B characteristicFunction: protection of end user single-phase circuits against overload and short-circuit currents; protection against the effects of sinusoidal alternating and direct pulsating earth fault currents; pro-tection against indirect contact and additional protection against direct contact (IΔn=30 mA).



Icn=6 kA


2 30 6 DS202C B6 A30 2CSR252140R1065 132257 0.240 5

10 DS202C B10 A30 2CSR252140R1105 132356 0.240 5

13 DS202C B13 A30 2CSR252140R1135 132455 0.240 5

16 DS202C B16 A30 2CSR252140R1165 132554 0.240 5

20 DS202C B20 A30 2CSR252140R1205 132653 0.240 5

25 DS202C B25 A30 2CSR252140R1255 132752 0.240 5

32 DS202C B32 A30 2CSR252140R1325 132851 0.240 5

300 6 DS202C B6 A300 2CSR252140R3065 132950 0.240 5

10 DS202C B10 A300 2CSR252140R3105 133056 0.240 5

13 DS202C B13 A300 2CSR252140R3135 133155 0.240 5

16 DS202C B16 A300 2CSR252140R3165 133254 0.240 5

20 DS202C B20 A300 2CSR252140R3205 133353 0.240 5

25 DS202C B25 A300 2CSR252140R3255 133452 0.240 5

32 DS202C B32 A300 2CSR252140R3325 133551 0.240 5

B

Selection tablesRCBOs DS202C series 6000 A y type

DS202C ASystem pro M compact®

2CS

C40

0006

F020

2


3/45ABB

3


DS202C A type, C characteristicFunction: protection of end user single-phase circuits against overload and short-circuit currents; protection against the effects of sinusoidal alternating and direct pulsating earth fault currents; pro-tection against indirect contact and additional protection against direct contact (IΔn=30 mA).



Icn=6 kA


2 30 6 DS202C C6 A30 2CSR252140R1064 122357 0.240 5

10 DS202C C10 A30 2CSR252140R1104 122456 0.240 5

13 DS202C C13 A30 2CSR252140R1134 122555 0.240 5

16 DS202C C16 A30 2CSR252140R1164 122654 0.240 5

20 DS202C C20 A30 2CSR252140R1204 122753 0.240 5

25 DS202C C25 A30 2CSR252140R1254 122852 0.240 5

32 DS202C C32 A30 2CSR252140R1324 122951 0.240 5

300 6 DS202C C6 A300 2CSR252140R3064 123057 0.240 5

10 DS202C C10 A300 2CSR252140R3104 123156 0.240 5

13 DS202C C13 A300 2CSR252140R3134 123255 0.240 5

16 DS202C C16 A300 2CSR252140R3164 123354 0.240 5

20 DS202C C20 A300 2CSR252140R3204 123453 0.240 5

25 DS202C C25 A300 2CSR252140R3254 123552 0.240 5

32 DS202C C32 A300 2CSR252140R3324 123651 0.240 5

C


DS202C ASystem pro M compact®

2CS

C40

0005

F020

2


3/46 ABB

3


DS202C M A type, C characteristicFunction: protection of end user single-phase circuits against overload and short-circuit currents; protection against the effects of sinusoidal alternating earth fault currents; protection against indirect contact and additional protection against direct contact (IΔn=30 mA).



Icn=10 kA


1+N 10 13 DS202C M C13 A10 2CSR272140R0134 117957 0.240 5

16 DS202C M C16 A10 2CSR272140R0164 118053 0.240 5

30 6 DS202C M C6 A30 2CSR272140R1064 118855 0.240 5

10 DS202C M C10 A30 2CSR272140R1104 118954 0.240 5

13 DS202C M C13 A30 2CSR272140R1134 119050 0.240 5

16 DS202C M C16 A30 2CSR272140R1164 119159 0.240 5

20 DS202C M C20 A30 2CSR272140R1204 119258 0.240 5

25 DS202C M C25 A30 2CSR272140R1254 119357 0.240 5

32 DS202C M C32 A30 2CSR272140R1324 119456 0.240 5

300 6 DS202C M C6 A300 2CSR272140R3064 120254 0.240 5

10 DS202C M C10 A300 2CSR272140R3104 120353 0.240 5

13 DS202C M C13 A300 2CSR272140R3134 120452 0.240 5

16 DS202C M C16 A300 2CSR272140R3164 120551 0.240 5

20 DS202C M C20 A300 2CSR272140R3204 120650 0.240 5

25 DS202C M C25 A300 2CSR272140R3254 120759 0.240 5

32 DS202C M C32 A300 2CSR272140R3324 120858 0.240 5

C

DS202C M A type, B characteristicFunction: protection of end user single-phase circuits against overload and short-circuit currents; protection against the effects of sinusoidal alternating and direct pulsating earth fault currents; pro-tection against indirect contact and additional protection against direct contact (IΔn=30 mA).



Icn=10 kA


1+N 10 10 DS202C M B10 A10 2CSR272140R0105 124856 0.240 5

13 DS202C M B13 A10 2CSR272140R0135 117759 0.240 5

16 DS202C M B16 A10 2CSR272140R0165 117858 0.240 5

30 6 DS202C M B6 A30 2CSR272140R1065 118152 0.240 5

10 DS202C M B10 A30 2CSR272140R1105 118251 0.240 5

13 DS202C M B13 A30 2CSR272140R1135 118350 0.240 5

16 DS202C M B16 A30 2CSR272140R1165 118459 0.240 5

20 DS202C M B20 A30 2CSR272140R1205 118558 0.240 5

25 DS202C M B25 A30 2CSR272140R1255 118657 0.240 5

32 DS202C M B32 A30 2CSR272140R1325 118756 0.240 5

300 6 DS202C M B6 A300 2CSR272140R3065 119555 0.240 5

10 DS202C M B10 A300 2CSR272140R3105 119654 0.240 5

13 DS202C M B13 A300 2CSR272140R3135 119753 0.240 5

16 DS202C M B16 A300 2CSR272140R3165 119852 0.240 5

20 DS202C M B20 A300 2CSR272140R3205 119951 0.240 5

25 DS202C M B25 A300 2CSR272140R3255 120056 0.240 5

32 DS202C M B32 A300 2CSR272140R3325 120155 0.240 5

B


DS202C M ASystem pro M compact®

2CS

C40

0005

F020

22C

SC

4000

05F0

202


3/47ABB

3


DS202C M APR type, B characteristicFunction: protection of end user single-phase circuits against overload and short-circuit currents; protection against the effects of sinusoidal alternating and direct pulsating earth fault currents; pro-tection against indirect contact and additional protection against direct contact (IΔn=30 mA).



Icn=10 kA


2 30 6 DS202C M B6 APR30 2CSR272440R1065 120957 0.240 5

10 DS202C M B10 APR30 2CSR272440R1105 121053 0.240 5

13 DS202C M B13 APR30 2CSR272440R1135 121152 0.240 5

16 DS202C M B16 APR30 2CSR272440R1165 121251 0.240 5

20 DS202C M B20 APR30 2CSR272440R1205 121350 0.240 5

25 DS202C M B25 APR30 2CSR272440R1255 121459 0.240 5

32 DS202C M B32 APR30 2CSR272440R1325 121558 0.240 5

300 6 DS202C M B6 APR300 2CSR272440R3065 124955 0.240 5

10 DS202C M B10 APR300 2CSR272440R3105 125051 0.240 5

13 DS202C M B13 APR300 2CSR272440R3135 125150 0.240 5

16 DS202C M B16 APR300 2CSR272440R3165 125259 0.240 5

20 DS202C M B20 APR300 2CSR272440R3205 125358 0.240 5

25 DS202C M B25 APR300 2CSR272440R3255 125457 0.240 5

32 DS202C M B32 APR300 2CSR272440R3325 125556 0.240 5

DS202C M APR type, C characteristicFunction: protection of end user single-phase circuits against overload and short-circuit currents; protection against the effects of sinusoidal alternating and direct pulsating earth fault currents; pro-tection against indirect contact and additional protection against direct contact (IΔn=30 mA).



Icn=10 kA


2 30 6 DS202C M C6 APR30 2CSR272440R1064 121657 0.240 5

10 DS202C M C10 APR30 2CSR272440R1104 121756 0.240 5

13 DS202C M C13 APR30 2CSR272440R1134 121855 0.240 5

16 DS202C M C16 APR30 2CSR272440R1164 121954 0.240 5

20 DS202C M C20 APR30 2CSR272440R1204 122050 0.240 5

25 DS202C M C25 APR30 2CSR272440R1254 122159 0.240 5

32 DS202C M C32 APR30 2CSR272440R1324 122258 0.240 5

Selection tablesRCBOs DS202C series 10000 A y APR type

DS202C M APR

C

B


2CS

C40

0005

F020

22C

SC

4000

05F0

202


3/48 ABB

3TECHNICAL CHARACTERISTICSStandards

Electrical Operating characteristic: type (wave form of the earth leakage sensed)features Poles

Rated sensitivity IΔn ARated current In ARated voltage Ue 2P, 3P, 4P V

Rated residual operating current AInsulation voltage Ui VMax. operating voltage of circuit test VMin. operating voltage of circuit test VRated frequency HzRated breaking capacity acc. to IEC/EN 61009 ultimate Icn ARated breaking capacity ultimate Icu kAacc. to IEC/EN 60947-2 1P+N @230 VAC, 2P, 3P, 4P @400 VAC service Ics kARated residual breaking capacity IΔm kARated impulse withstand voltage (1.2/50) Uimp kVDielectric test voltage at ind. freq. for 1 min. kVOvervoltage categoryThermomagnetic release B: 3 In ≤ Im ≤ 5 Incharacteristic C: 5 In ≤ Im ≤ 10 In


Mechanical Toggle 2P, 3P, 4Pfeatures Electrical life

Mechanical lifeProtection degree housing

terminalsTropicalization humid heat °C/RHacc. to IEC /EN 60068-2 constant climatic conditions °C/RH

variable climatic conditions °C/RHReference temperature for setting of thermal element °CAmbient temperature (with daily average ≤ +35 °C) °CStorage temperature °C

Installation Terminal type topbottom 2P 3P/4P In ≤ 40 A 3P/4P 50 A ≤ In ≤ 63 A

Terminal size top/bottom per cable 2P mm2

3P/4P In ≤ 40 A mm2

3P/4P 50 A ≤ In ≤ 63 A mm2

Tightening torque top/bottom 2P N*m3P/4P In ≤ 40 A N*m3P/4P 50 A ≤ In ≤ 63 A N*m

MountingConnection

Dimensions Dimensions (H x D x W) 2P mmand weight 3P In ≤ 40 A mm

4P In ≤ 40 A mm3P 50 A ≤ In ≤ 63 A mm4P 50 A ≤ In ≤ 63 A mm

Weight 2P g3P In ≤ 40 A g4P In ≤ 40 A g3P 50 A ≤ In ≤ 63 A g4P 50 A ≤ In ≤ 63 A g

Combination Combinable with: auxiliary contactwith auxiliary signal contact/auxiliary switchelements shunt trip

undervoltage release� Available depending on type and characteristic curve. For 2P RCBOs A type B-C curves up to 32 A, refer to DS202C 2 protected poles RCBOs in only two modules� Prior to connection of aluminium conductors (≥ 4 mm2) ensure that their contact points are cleaned, brushed and coated with grease

Technical featuresRCBOs DS 200 series


DS 200


3/49ABB

3



DS 200

DS 200 AC DS 200 A DS 200 M AC DS 200 M AIEC/EN 61009, IEC/EN 60947-2

AC A AC A2P, 3P, 4P

0.036 ≤In ≤ 63 �

230-240230/400 - 240/415

0.03500

254 (440 for 3P and 4P)110 (195 for 3P and 4P)

50…606000 6000 10000 1000010 10 15 157.5 7.5 11.2 11.26 6 10 10

62.5

III, disconnector abilities

250black (MCB) sealable in ON-OFF position + blue (RCD)

1000020000IP4XIP2X

28 cycles with 55/95…10023/83 - 40/93 - 55/20

25/95 - 40/9530

-25…+55-25…+55

failsafe bidirectional cylinder-lift terminal (shock protected) �failsafe bidirectional cylinder-lift terminal (shock protected) �

cage (shock protected)failsafe bidirectional cylinder-lift terminal (shock protected) �

(rigid and flexible) up to 25/25(rigid and flexible) up to 25/16(rigid and flexible) up to 25/25

2.8/2.82.8/1.22.8/2.8

on DIN rail EN 60715 (35 mm) by means of fast clip device715 (35 mm) by means of fast clip devicefrom top and bottom

85 x 69 x 7085 x 69 x 87.585 x 69 x 105

85 x 69 x 122.585 x 69 x 140

475625775775925yesyesyesyes


3/50 ABB

3

Technical details .......................... pag. 11/76 Overall dimensions ....................... pag. 13/8


B

Selection tablesRCBOs DS 200 series

6000 - AC w type

DS 200 AC B

DS 200 AC type, B characteristicFunction: protection against overload and short-circuit currents; protection against the effects of sinusoidal alternating earth fault currents; protection against indirect contacts and additional pro-tection against direct contacts.


Standard: IEC/EN 61009 and IEC/EN 60947-2

Icn=6 kA

Number Type/ Rated Rated Order Bbn Price Price Weight Packof poles class residual current details 8012542 1 piece group 1 piece unit current IΔn mA In A Type code Order code EAN kg pc.

2 AC 30 6 DS202 AC-B6/0.03 2CSR252001R1065 863502 0.440 1

10 DS202 AC-B10/0.03 2CSR252001R1105 863601 0.440 1

13 DS202 AC-B13/0.03 2CSR252001R1135 863700 0.440 1

16 DS202 AC-B16/0.03 2CSR252001R1165 863809 0.440 1

20 DS202 AC-B20/0.03 2CSR252001R1205 863908 0.440 1

25 DS202 AC-B25/0.03 2CSR252001R1255 864004 0.440 1

32 DS202 AC-B32/0.03 2CSR252001R1325 864103 0.440 1

40 DS202 AC-B40/0.03 2CSR252001R1405 864202 0.440 1

50 � DS202 AC-B50/0.03 2CSR252001R1505 864301 0.440 1

63 � DS202 AC-B63/0.03 2CSR252001R1635 864400 0.440 1

3 AC 30 6 DS203 AC-B6/0.03 2CSR253001R1065 865506 0.610 1

10 DS203 AC-B10/0.03 2CSR253001R1105 865605 0.610 1

13 DS203 AC-B13/0.03 2CSR253001R1135 865704 0.610 1

16 DS203 AC-B16/0.03 2CSR253001R1165 865803 0.610 1

20 DS203 AC-B20/0.03 2CSR253001R1205 865902 0.610 1

25 DS203 AC-B25/0.03 2CSR253001R1255 866008 0.610 1

32 DS203 AC-B32/0.03 2CSR253001R1325 866107 0.610 1

40 DS203 AC-B40/0.03 2CSR253001R1405 866206 0.610 1

50 � DS203 AC-B50/0.03 2CSR253001R1505 866305 0.650 1

63 � DS203 AC-B63/0.03 2CSR253001R1635 866404 0.650 1

4 AC 30 6 DS204 AC-B6/0.03 2CSR254001R1065 867500 0.780 1

10 DS204 AC-B10/0.03 2CSR254001R1105 867609 0.780 1

13 DS204 AC-B13/0.03 2CSR254001R1135 867708 0.780 1

16 DS204 AC-B16/0.03 2CSR254001R1165 867807 0.780 1

20 DS204 AC-B20/0.03 2CSR254001R1205 867906 0.780 1

25 DS204 AC-B25/0.03 2CSR254001R1255 868002 0.780 1

32 DS204 AC-B32/0.03 2CSR254001R1325 868101 0.780 1

40 DS204 AC-B40/0.03 2CSR254001R1405 868200 0.780 1

50 � DS204 AC-B50/0.03 2CSR254001R1505 868309 0.825 1

63 � DS204 AC-B63/0.03 2CSR254001R1635 868408 0.825 1


1/2 3/4 5/6 7/8

In up to 40 A

1/2 3/4 1/2 3/4

1/2 3/4 5/6

1/2 3/4

2/1 4/3

5/6

6/5

7/8

8/7

In=50-63 AY1 Y2

1/2 3/4

2/1 4/3

5/6

6/5

In=50-63 AY1 Y2

2CS

C40

0191

F020

12C

SC

4001

93F0

201

2CS

C40

0194

F020

1


3/51ABB

3



C


6000 - AC w type

DS 200 AC C

DS 200 AC type, C characteristicFunction: protection against overload and short-circuit currents; protection against the effects of sinusoidal alternating earth fault currents; protection against indirect contacts and additional pro-tection against direct contacts.



Icn=6 kA


2 AC 30 6 DS202 AC-C6/0.03 2CSR252001R1064 869504 0.440 1

10 DS202 AC-C10/0.03 2CSR252001R1104 869603 0.440 1

13 DS202 AC-C13/0.03 2CSR252001R1134 869702 0.440 1

16 DS202 AC-C16/0.03 2CSR252001R1164 869801 0.440 1

20 DS202 AC-C20/0.03 2CSR252001R1204 869900 0.440 1

25 DS202 AC-C25/0.03 2CSR252001R1254 870005 0.440 1

32 DS202 AC-C32/0.03 2CSR252001R1324 870104 0.440 1

40 DS202 AC-C40/0.03 2CSR252001R1404 870203 0.440 1

50 � DS202 AC-C50/0.03 2CSR252001R1504 870302 0.440 1

63 � DS202 AC-C63/0.03 2CSR252001R1634 870401 0.440 1

3 AC 30 6 DS203 AC-C6/0.03 2CSR253001R1064 871507 0.610 1

10 DS203 AC-C10/0.03 2CSR253001R1104 871606 0.610 1

13 DS203 AC-C13/0.03 2CSR253001R1134 871705 0.610 1

16 DS203 AC-C16/0.03 2CSR253001R1164 871804 0.610 1

20 DS203 AC-C20/0.03 2CSR253001R1204 871903 0.610 1

25 DS203 AC-C25/0.03 2CSR253001R1254 872009 0.610 1

32 DS203 AC-C32/0.03 2CSR253001R1324 872108 0.610 1

40 DS203 AC-C40/0.03 2CSR253001R1404 872207 0.610 1

50 � DS203 AC-C50/0.03 2CSR253001R1504 872306 0.650 1

63 � DS203 AC-C63/0.03 2CSR253001R1634 872405 0.650 1

4 AC 30 6 DS204 AC-C6/0.03 2CSR254001R1064 873501 0.780 1

10 DS204 AC-C10/0.03 2CSR254001R1104 873600 0.780 1

13 DS204 AC-C13/0.03 2CSR254001R1134 873709 0.780 1

16 DS204 AC-C16/0.03 2CSR254001R1164 873808 0.780 1

20 DS204 AC-C20/0.03 2CSR254001R1204 873907 0.780 1

25 DS204 AC-C25/0.03 2CSR254001R1254 874003 0.780 1

32 DS204 AC-C32/0.03 2CSR254001R1324 874102 0.780 1

40 DS204 AC-C40/0.03 2CSR254001R1404 874201 0.780 1

50 � DS204 AC-C50/0.03 2CSR254001R1504 874300 0.825 1

63 � DS204 AC-C63/0.03 2CSR254001R1634 874409 0.825 1


1/2 3/4 5/6 7/8

In up to 40 A

1/2 3/4 1/2 3/4

1/2 3/4 5/6

1/2 3/4

2/1 4/3

5/6

6/5

7/8

8/7

In=50-63 AY1 Y2

1/2 3/4

2/1 4/3

5/6

6/5

In=50-63 AY1 Y2

2CS

C40

0191

F020

12C

SC

4001

93F0

201

2CS

C40

0194

F020

1


3/52 ABB

3



B


6000 - A y type

DS 200 A B

DS 200 A type, B characteristicFunction: protection against overload and short-circuit currents; protection against the effects of sinusoidal alternating and direct pulsating earth fault currents; protection against indirect contacts and additional protection against direct contacts.



Icn=6 kA


2 A 30 40 DS202 A-B40/0.03 2CSR252101R1405 858201 0.440 1

50 � DS202 A-B50/0.03 2CSR252101R1505 858300 0.440 1

63 � DS202 A-B63/0.03 2CSR252101R1635 858409 0.440 1

3 A 30 6 DS203 A-B6/0.03 2CSR253101R1065 858508 0.610 1

10 DS203 A-B10/0.03 2CSR253101R1105 858607 0.610 1

13 DS203 A-B13/0.03 2CSR253101R1135 858706 0.610 1

16 DS203 A-B16/0.03 2CSR253101R1165 858805 0.610 1

20 DS203 A-B20/0.03 2CSR253101R1205 858904 0.610 1

25 DS203 A-B25/0.03 2CSR253101R1255 859000 0.610 1

32 DS203 A-B32/0.03 2CSR253101R1325 859109 0.610 1

40 DS203 A-B40/0.03 2CSR253101R1405 859208 0.610 1

50 � DS203 A-B50/0.03 2CSR253101R1505 859307 0.650 1

63 � DS203 A-B63/0.03 2CSR253101R1635 859406 0.650 1

4 A 30 6 DS204 A-B6/0.03 2CSR254101R1065 859505 0.780 1

10 DS204 A-B10/0.03 2CSR254101R1105 859604 0.780 1

13 DS204 A-B13/0.03 2CSR254101R1135 859703 0.780 1

16 DS204 A-B16/0.03 2CSR254101R1165 859802 0.780 1

20 DS204 A-B20/0.03 2CSR254101R1205 859901 0.780 1

25 DS204 A-B25/0.03 2CSR254101R1255 860006 0.780 1

32 DS204 A-B32/0.03 2CSR254101R1325 860105 0.780 1

40 DS204 A-B40/0.03 2CSR254101R1405 860204 0.780 1

50 � DS204 A-B50/0.03 2CSR254101R1505 860303 0.825 1

63 � DS204 A-B63/0.03 2CSR254101R1635 860402 0.825 1


1/2 3/4 1/2 3/4

1/2 3/4 5/6

1/2 3/4

2/1 4/3

5/6

6/5

7/8

8/7

In=50-63 AY1 Y2

1/2 3/4

2/1 4/3

5/6

6/5

In=50-63 AY1 Y2

1/2 3/4 5/6 7/8

In up to 40 A

2CS

C40

0191

F020

12C

SC

4001

93F0

201

2CS

C40

0194

F020

1


3/53ABB

3



C


6000 - A y type

DS 200 A C

DS 200 A type, C characteristicFunction: protection against overload and short-circuit currents; protection against the effects of sinusoidal alternating and direct pulsating earth fault currents; protection against indirect contacts and additional protection against direct contacts.



Icn=6 kA


2 A 30 40 DS202 A-C40/0.03 2CSR252101R1404 861201 0.440 1

50 � DS202 A-C50/0.03 2CSR252101R1504 861300 0.440 1

63 � DS202 A-C63/0.03 2CSR252101R1634 861409 0.440 1

3 A 30 6 DS203 A-C6/0.03 2CSR253101R1064 861508 0.610 1

10 DS203 A-C10/0.03 2CSR253101R1104 861607 0.610 1

13 DS203 A-C13/0.03 2CSR253101R1134 861706 0.610 1

16 DS203 A-C16/0.03 2CSR253101R1164 861805 0.610 1

20 DS203 A-C20/0.03 2CSR253101R1204 861904 0.610 1

25 DS203 A-C25/0.03 2CSR253101R1254 862000 0.610 1

32 DS203 A-C32/0.03 2CSR253101R1324 862109 0.610 1

40 DS203 A-C40/0.03 2CSR253101R1404 862208 0.610 1

50 � DS203 A-C50/0.03 2CSR253101R1504 862307 0.650 1

63 � DS203 A-C63/0.03 2CSR253101R1634 862406 0.650 1

4 A 30 6 DS204 A-C6/0.03 2CSR254101R1064 862505 0.780 1

10 DS204 A-C10/0.03 2CSR254101R1104 862604 0.780 1

13 DS204 A-C13/0.03 2CSR254101R1134 862703 0.780 1

16 DS204 A-C16/0.03 2CSR254101R1164 862802 0.780 1

20 DS204 A-C20/0.03 2CSR254101R1204 862901 0.780 1

25 DS204 A-C25/0.03 2CSR254101R1254 863007 0.780 1

32 DS204 A-C32/0.03 2CSR254101R1324 863106 0.780 1

40 DS204 A-C40/0.03 2CSR254101R1404 863205 0.780 1

50 � DS204 A-C50/0.03 2CSR254101R1504 863304 0.825 1

63 � DS204 A-C63/0.03 2CSR254101R1634 863403 0.825 1


1/2 3/4 1/2 3/4

1/2 3/4 5/6

1/2 3/4

2/1 4/3

5/6

6/5

7/8

8/7

In=50-63 AY1 Y2

1/2 3/4

2/1 4/3

5/6

6/5

In=50-63 AY1 Y2

1/2 3/4 5/6 7/8

In up to 40 A

2CS

C40

0191

F020

12C

SC

4001

93F0

201

2CS

C40

0194

F020

1


3/54 ABB

3



C


6000 - A y type

DS 200 A K

DS 200 A type, K characteristicFunction: protection and control against overloads and short-circuit in systems where motors, tran-sformers and auxiliary circuits are present. Advantages: no unwanted release in case of currents peak up to 8 x In, according to the series; thanks to the high sensibility bimetal, the K curve switches offer protection of the sensible elements from overcurrents; they also allow the best protection of cables and lines.



Icn=6 kA


2 A 30 6 DS202 A-K6/0.03 2CSR252101R1067 930303 0.475 1

10 DS202 A-K10/0.03 2CSR252101R1107 900702 0.475 1

13 DS202 A-K13/0.03 2CSR252101R1137 930402 0.475 1

16 DS202 A-K16/0.03 2CSR252101R1167 930501 0.475 1

20 DS202 A-K20/0.03 2CSR252101R1207 930600 0.475 1

25 DS202 A-K25/0.03 2CSR252101R1257 930709 0.475 1

32 DS202 A-K32/0.03 2CSR252101R1327 930808 0.475 1

40 DS202 A-K40/0.03 2CSR252101R1407 930907 0.475 1

50 DS202 A-K50/0.03 2CSR252101R1507 931003 0.475 1

63 DS202 A-K63/0.03 2CSR252101R1637 931102 0.475 1

4 A 30 6 DS204 A-K6/0.03 2CSR254101R1067 931201 0.775 1

10 DS204 A-K10/0.03 2CSR254101R1107 931300 0.775 1

13 DS204 A-K13/0.03 2CSR254101R1137 931409 0.775 1

16 DS204 A-K16/0.03 2CSR254101R1167 931508 0.775 1

20 DS204 A-K20/0.03 2CSR254101R1207 931607 0.775 1

25 DS204 A-K25/0.03 2CSR254101R1257 931706 0.775 1

32 DS204 A-K32/0.03 2CSR254101R1327 931805 0.775 1

40 DS204 A-K40/0.03 2CSR254101R1407 931904 0.775 1

50 DS204 A-K50/0.03 2CSR254101R1507 932000 0.775 1

63 DS204 A-K63/0.03 2CSR254101R1637 932109 0.775 1


1/2 3/4 1/2 3/4

1/2 3/4

2/1 4/3

5/6

6/5

7/8

8/7

In=50-63 AY1 Y2

1/2 3/4 5/6 7/8

In up to 40 A

2CS

C40

0191

F020

12C

SC

4001

94F0

201


3/55ABB

3



B

Selection tablesRCBOs DS 200 series M 10000 - AC w type

DS 200 M AC B

DS 200 M AC type, B characteristicFunction: protection against overload and short-circuit currents; protection against the effects of sinusoidal alternating earth fault currents; protection against indirect contacts and additional pro-tection against direct contacts.



Icn=10 kA


2 AC 30 6 DS202 M AC-B6/0.03 2CSR272001R1065 932208 0.440 1

10 DS202 M AC-B10/0.03 2CSR272001R1105 932307 0.440 1

13 DS202 M AC-B13/0.03 2CSR272001R1135 932406 0.440 1

16 DS202 M AC-B16/0.03 2CSR272001R1165 932505 0.440 1

20 DS202 M AC-B20/0.03 2CSR272001R1205 932604 0.440 1

25 DS202 M AC-B25/0.03 2CSR272001R1255 932703 0.440 1

32 DS202 M AC-B32/0.03 2CSR272001R1325 932802 0.440 1

40 DS202 M AC-B40/0.03 2CSR272001R1405 932901 0.440 1

50 � DS202 M AC-B50/0.03 2CSR272001R1505 933007 0.440 1

63 � DS202 M AC-B63/0.03 2CSR272001R1635 933106 0.440 1

3 AC 30 6 DS203 M AC-B6/0.03 2CSR273001R1065 933205 0.610 1

10 DS203 M AC-B10/0.03 2CSR273001R1105 933304 0.610 1

13 DS203 M AC-B13/0.03 2CSR273001R1135 933403 0.610 1

16 DS203 M AC-B16/0.03 2CSR273001R1165 933502 0.610 1

20 DS203 M AC-B20/0.03 2CSR273001R1205 933601 0.610 1

25 DS203 M AC-B25/0.03 2CSR273001R1255 933700 0.610 1

32 DS203 M AC-B32/0.03 2CSR273001R1325 933809 0.610 1

40 DS203 M AC-B40/0.03 2CSR273001R1405 933908 0.610 1

50 � DS203 M AC-B50/0.03 2CSR273001R1505 934004 0.650 1

63 � DS203 M AC-B63/0.03 2CSR273001R1635 934103 0.650 1

4 AC 30 6 DS204 M AC-B6/0.03 2CSR274001R1065 934202 0.780 1

10 DS204 M AC-B10/0.03 2CSR274001R1105 934301 0.780 1

13 DS204 M AC-B13/0.03 2CSR274001R1135 934400 0.780 1

16 DS204 M AC-B16/0.03 2CSR274001R1165 934509 0.780 1

20 DS204 M AC-B20/0.03 2CSR274001R1205 934608 0.780 1

25 DS204 M AC-B25/0.03 2CSR274001R1255 934707 0.780 1

32 DS204 M AC-B32/0.03 2CSR274001R1325 934806 0.780 1

40 DS204 M AC-B40/0.03 2CSR274001R1405 934905 0.780 1

50 � DS204 M AC-B50/0.03 2CSR274001R1505 935001 0.825 1

63 � DS204 M AC-B63/0.03 2CSR274001R1635 935100 0.825 1


1/2 3/4 1/2 3/4

1/2 3/4 5/6

1/2 3/4

2/1 4/3

5/6

6/5

7/8

8/7

In=50-63 AY1 Y2

1/2 3/4

2/1 4/3

5/6

6/5

In=50-63 AY1 Y2

1/2 3/4 5/6 7/8

In up to 40 A

2CS

C40

0191

F020

12C

SC

4001

93F0

201

2CS

C40

0194

F020

1


3/56 ABB

3



C

Selection tablesRCBOs DS 200 series M 10000 - AC w type

DS 200 M AC C

DS 200 M AC type, C characteristicFunction: protection against overload and short-circuit currents; protection against the effects of sinusoidal alternating earth fault currents; protection against indirect contacts and additional pro-tection against direct contacts.



Icn=10 kA


2 AC 30 6 DS202 M AC-C6/0.03 2CSR272001R1064 851509 0.440 1

10 DS202 M AC-C10/0.03 2CSR272001R1104 851608 0.440 1

13 DS202 M AC-C13/0.03 2CSR272001R1134 851707 0.440 1

16 DS202 M AC-C16/0.03 2CSR272001R1164 851806 0.440 1

20 DS202 M AC-C20/0.03 2CSR272001R1204 851905 0.440 1

25 DS202 M AC-C25/0.03 2CSR272001R1254 852001 0.440 1

32 DS202 M AC-C32/0.03 2CSR272001R1324 852100 0.440 1

40 DS202 M AC-C40/0.03 2CSR272001R1404 852209 0.440 1

50 � DS202 M AC-C50/0.03 2CSR272001R1504 852308 0.440 1

63 � DS202 M AC-C63/0.03 2CSR272001R1634 852407 0.440 1

3 AC 30 6 DS203 M AC-C6/0.03 2CSR273001R1064 852506 0.610 1

10 DS203 M AC-C10/0.03 2CSR273001R1104 852605 0.610 1

13 DS203 M AC-C13/0.03 2CSR273001R1134 852704 0.610 1

16 DS203 M AC-C16/0.03 2CSR273001R1164 852803 0.610 1

20 DS203 M AC-C20/0.03 2CSR273001R1204 852902 0.610 1

25 DS203 M AC-C25/0.03 2CSR273001R1254 853008 0.610 1

32 DS203 M AC-C32/0.03 2CSR273001R1324 853107 0.610 1

40 DS203 M AC-C40/0.03 2CSR273001R1404 853206 0.610 1

50 � DS203 M AC-C50/0.03 2CSR273001R1504 853305 0.650 1

63 � DS203 M AC-C63/0.03 2CSR273001R1634 853404 0.650 1

4 AC 30 6 DS204 M AC-C6/0.03 2CSR274001R1064 853503 0.780 1

10 DS204 M AC-C10/0.03 2CSR274001R1104 853602 0.780 1

13 DS204 M AC-C13/0.03 2CSR274001R1134 853701 0.780 1

16 DS204 M AC-C16/0.03 2CSR274001R1164 853800 0.780 1

20 DS204 M AC-C20/0.03 2CSR274001R1204 853909 0.780 1

25 DS204 M AC-C25/0.03 2CSR274001R1254 854005 0.780 1

32 DS204 M AC-C32/0.03 2CSR274001R1324 854104 0.780 1

40 DS204 M AC-C40/0.03 2CSR274001R1404 854203 0.780 1

50 � DS204 M AC-C50/0.03 2CSR274001R1504 854302 0.825 1

63 � DS204 M AC-C63/0.03 2CSR274001R1634 854401 0.825 1


1/2 3/4 1/2 3/4

1/2 3/4 5/6

1/2 3/4

2/1 4/3

5/6

6/5

7/8

8/7

In=50-63 AY1 Y2

1/2 3/4

2/1 4/3

5/6

6/5

In=50-63 AY1 Y2

1/2 3/4 5/6 7/8

In up to 40 A

2CS

C40

0191

F020

12C

SC

4001

93F0

201

2CS

C40

0194

F020

1


3/57ABB

3



B

Selection tablesRCBOs DS 200 series M 10000 - A y type

DS 200 M A B

DS 200 M A type, B characteristicFunction: protection against overload and short-circuit currents; protection against the effects of sinusoidal alternating and direct pulsating earth fault currents; protection against indirect contacts and additional protection against direct contacts.



Icn=10 kA


2 A 30 40 DS202 M A-B40/0.03 2CSR272101R1405 846208 0.440 1

50 � DS202 M A-B50/0.03 2CSR272101R1505 846307 0.440 1

63 � DS202 M A-B63/0.03 2CSR272101R1635 846406 0.440 1

3 A 30 6 DS203 M A-B6/0.03 2CSR273101R1065 846505 0.610 1

10 DS203 M A-B10/0.03 2CSR273101R1105 846604 0.610 1

13 DS203 M A-B13/0.03 2CSR273101R1135 846703 0.610 1

16 DS203 M A-B16/0.03 2CSR273101R1165 846802 0.610 1

20 DS203 M A-B20/0.03 2CSR273101R1205 846901 0.610 1

25 DS203 M A-B25/0.03 2CSR273101R1255 847007 0.610 1

32 DS203 M A-B32/0.03 2CSR273101R1325 847106 0.610 1

40 DS203 M A-B40/0.03 2CSR273101R1405 847205 0.610 1

50 � DS203 M A-B50/0.03 2CSR273101R1505 847304 0.650 1

63 � DS203 M A-B63/0.03 2CSR273101R1635 847403 0.650 1

4 A 30 6 DS204 M A-B6/0.03 2CSR274101R1065 847502 0.780 1

10 DS204 M A-B10/0.03 2CSR274101R1105 847601 0.780 1

13 DS204 M A-B13/0.03 2CSR274101R1135 847700 0.780 1

16 DS204 M A-B16/0.03 2CSR274101R1165 847809 0.780 1

20 DS204 M A-B20/0.03 2CSR274101R1205 847908 0.780 1

25 DS204 M A-B25/0.03 2CSR274101R1255 848004 0.780 1

32 DS204 M A-B32/0.03 2CSR274101R1325 848103 0.780 1

40 DS204 M A-B40/0.03 2CSR274101R1405 848202 0.780 1

50 � DS204 M A-B50/0.03 2CSR274101R1505 848301 0.825 1

63 � DS204 M A-B63/0.03 2CSR274101R1635 848400 0.825 1


1/2 3/4 1/2 3/4

1/2 3/4 5/6

1/2 3/4

2/1 4/3

5/6

6/5

7/8

8/7

In=50-63 AY1 Y2

1/2 3/4

2/1 4/3

5/6

6/5

In=50-63 AY1 Y2

1/2 3/4 5/6 7/8

In up to 40 A

2CS

C40

0191

F020

12C

SC

4001

93F0

201

2CS

C40

0194

F020

1


3/58 ABB

3



C


DS 200 M A C

DS 200 M A type, C characteristicFunction: protection against overload and short-circuit currents; protection against the effects of sinusoidal alternating and direct pulsating earth fault currents; protection against indirect contacts and additional protection against direct contacts.



Icn=10 kA


2 A 30 40 DS202 M A-C40/0.03 2CSR272101R1404 849209 0.440 1

50 � DS202 M A-C50/0.03 2CSR272101R1504 849308 0.440 1

63 � DS202 M A-C63/0.03 2CSR272101R1634 849407 0.440 1

3 A 30 6 DS203 M A-C6/0.03 2CSR273101R1064 849506 0.610 1

10 DS203 M A-C10/0.03 2CSR273101R1104 849605 0.610 1

13 DS203 M A-C13/0.03 2CSR273101R1134 849704 0.610 1

16 DS203 M A-C16/0.03 2CSR273101R1164 849803 0.610 1

20 DS203 M A-C20/0.03 2CSR273101R1204 849902 0.610 1

25 DS203 M A-C25/0.03 2CSR273101R1254 850007 0.610 1

32 DS203 M A-C32/0.03 2CSR273101R1324 850106 0.610 1

40 DS203 M A-C40/0.03 2CSR273101R1404 850205 0.610 1

50 � DS203 M A-C50/0.03 2CSR273101R1504 850304 0.650 1

63 � DS203 M A-C63/0.03 2CSR273101R1634 850403 0.650 1

1/2 3/4 1/2 3/4

1/2 3/4 5/6

1/2 3/4

2/1 4/3

5/6

6/5

In=50-63 AY1 Y2

2CS

C40

0191

F020

12C

SC

4001

93F0

201


3/59ABB

3

1/2 3/4

2/1 4/3

5/6

6/5

7/8

8/7

In=50-63 AY1 Y2

1/2 3/4 5/6 7/8

In up to 40 A

2CS

C40

0194

F020

1

4 A 30 6 DS204 M A-C6/0.03 2CSR274101R1064 850502 0.780 1

10 DS204 M A-C10/0.03 2CSR274101R1104 850601 0.780 1

13 DS204 M A-C13/0.03 2CSR274101R1134 850700 0.780 1

16 DS204 M A-C16/0.03 2CSR274101R1164 850809 0.780 1

20 DS204 M A-C20/0.03 2CSR274101R1204 850908 0.780 1

25 DS204 M A-C25/0.03 2CSR274101R1254 851004 0.780 1

32 DS204 M A-C32/0.03 2CSR274101R1324 851103 0.780 1

40 DS204 M A-C40/0.03 2CSR274101R1404 851202 0.780 1

50 � DS204 M A-C50/0.03 2CSR274101R1504 851301 0.825 1

63 � DS204 M A-C63/0.03 2CSR274101R1634 851400 0.825 1





DS 200 M A C


2/60 ABB SACE

3

The range of DDA 60, 70 and selective 90 RCD blocks for the S 290 series includes 100A devices suitable for assembly with MCBs in the S 290 series of type C only.

The DDA 800 RCD blocks for protecting people and electrical installations are useful when a higher breaking capacity is required. Assembling a DDA 800 RCD block with an S 800 N or S 800 S MCB creates an RCBO with a breaking capacity of 36 kA and 50 kA respectively. The RCD-blocks must be mounted on the right side of the MCB, so that the available accessories can be mounted on the left side. DDA 800 RCD blocks are available in AC and A, A AP-R (high immunity) and A selective types. DS 800 RCBOs are available, only in the size of 125 A, in A, AP-R (high immunity) and A selective types.

In compliance with IEC EN 61009, which establishes that the RCD blocks can be assembled with an MCB only once, the S 290 series DDA blocks have a mechanical pin which prevents disassembly once inserted.

In contrast, RCD blocks for the S 800 series which conform to IEC EN 60947-2 app. B do not have unlosable coupling elements.

DDA RCD blocks for the S 290 and S 800 series are

not sensit ive to impulsive atmospheric and operational discharges, therefore, they are not subject to unwanted tripping in accordance with IEC EN 61008, and IEC EN 61009, even with 8/20 μs wave up to 250 A.

2CS

C40

0170

F020

12C

SC

4002

74F0

201

2CS

C40

0273

F020

1


3/61ABB SACE

3

Residual current devices DDA for S 290 and S800 series, RCBOs DS800 and1P+N RCBOs DS271,RD2, RD3, RD residual current relays and TR toroidal transformers

Index

Technical features of RCDs-blocks for MCBs S 290 series ........................................ 3/62

Selection tables of RCDs-blocks for MCBs S 290 series

DDA 60, DDA 70 and DDA 90 for MCBs S 290 series ........................................................ 3/64

Technical features of RCDs-blocks for MCBs S800 series ......................................... 3/66

Selection tables of RCD-blocks for MCBs S800 series

DDA 800 for MCBs S800 series .......................................................................................... 3/68

Technical features of DS800 RCBOs series .................................................................. 3/72

Selection tables of DS800 RCBOs series

DS800 RCBOs series .......................................................................................................... 3/74

Technical features of 1P+N RCBOs DS271 series ........................................................ 3/80

Selection tables of 1P+N RCBOs DS271 series

DS271 RCBOs series .......................................................................................................... 3/82

Selection tables of residual current relays RD2, RD3, RD and toroidal transformers TRRD2 residual current relays ................................................................................................. 3/84RD3 residual current relays ................................................................................................. 3/85RD front panel residual current relays ................................................................................. 3/86TR toroidal transformers ...................................................................................................... 3/87


3/62 ABB

3 TECHNICAL FEATURESStandards


Rated current In ARated sensitivity IΔn ARated voltage UN VInsulation voltage Ui VMax. operating voltage of circuit test VMin. operating voltage of circuit test VRated frequency HzRated breaking capacity (Icn) acc. to IEC /EN 61009 ARated breaking capacity (Icn) acc. to IEC/EN 60947-2 ARated residual breaking capacity IΔm kARated impulse withstand voltage (1.2/50) Uimp kVDielectric test voltage at ind. freq. for 1 min. kVSurge current resistance (wave 8/20) A

Mechanical Togglefeatures Electrical life



variable climatic conditions °C/RHAmbient temperature (with daily average ≤ +35 °C) °CStorage temperature °C

Installation Terminal size for cables mm2

Tightening torque N*mMounting

Dimensions Dimensions (H x D x W) 2P mmand weight 3P/4P mm

Weight 2P g3P/4P g

Combinationwith auxiliary elements

Combinable with: S 290 C characteristicS 290 D and K characteristics

Technical featuresRCD-blocks for MCBs S 290 series

DDA 60 DDA 70 DDA 90



3/63ABB

3

Technical featuresRCD-blocks for MCBs S 290 series

DDA 60 DDA 70 DDA 90

DDA 60 DDA 70 DDA 90IEC/EN 61009 Ann. G

AC A A - A selective2P, 4P100

0.03-0.3 0.03-0.3 0.3-1230/400

500240(2P), 415(4P)100(2P), 175(4P)

50…60according to the breaking capacity of the associated MCBaccording to the breaking capacity of the associated MCB

7.54

2.5250 1000 3000

black operating from ON-OFF position1000020000IP4XIP2X

28 cycles with 55/95…10023/83 - 40/93 - 55/20

25/95 - 40/95-25…+45-40…+60

503.5

on DIN rail EN 60715 (35 mm) by means of rapid fixing device94 x 68 x 6194 x 68 x 90

325600yesno



3/64 ABB

3

Technical details .......................... pag. 11/76 Overall dimensions ...................... pag. 13/10

AC

Selection tablesRCD-blocks DDA 60 for MCBs S 290 series

DDA 60

DDA 60 AC type for MCBs S 290Function: RCD-block for assembly on site with MCBs S 290 series only in C characteristic. Protection against the effects of sinusoidal alternating earth fault currents; protection against indirect contacts and additional protection against direct (with IΔn=30 mA) contacts.Additional terminals for remote tripping are available.




2 0.03 100 DDA62 100 30MA 36229002 183307 0.325 1

0.3 100 DDA62 100 300MA 36229010 183505 0.325 1

4 0.03 100 DDA 64 100 30MA 36229044 183901 0.600 1

0.3 100 DDA 64 100 300MA 36229051 184106 0.600 1

Y1 Y2 2 4/N

2/14/3(N)

Y1 Y2 2 4 6 8/N

2/14/3

6/58/7(N)


2CS

C40

0167

F020

12C

SC

4001

69F0

201


3/65ABB

3


DDA 70 A type for MCBs S 290Function: RCD-block for assembly on site with MCBs S 290 series only in C characteristic. Protection against the effects of sinusoidal alternating and direct pulsating earth fault currents; protection against indirect contacts and additional protection against direct (with IΔn=30 mA) contacts.Additional terminals for remote tripping are available.




2 0.03 100 DDA 72 100 30MA 36229069 184304 0.325 1

0.3 100 DDA 72 100 300MA 36229077 184403 0.325 1

4 0.03 100 DDA 74 100 30MA 36229101 184700 0.600 1

0.3 100 DDA 74 100 300MA 36229119 184809 0.600 1

DDA 90 A selective type for MCBs S 290Function: RCD-block for assembly on site with MCBs S 290 series (only in C characteristic). Protection against the effects of sinusoidal alternating and direct pulsating earth fault currents with an intentional tripping delay, which permits to realize the selectivity with downstream instantaneous devices (for more information about selectivity see the technical guide).Additional terminals for remote tripping are available.



2 0.3 100 DDA 92 100 300MA S 36229127 185103 0.325 1

1 100 DDA 92 100 1A S 36229135 185509 0.325 1

4 0.3 100 DDA 94 100 300MA S 36229168 185905 0.600 1

1 100 DDA 94 100 1A S 36229176 186001 0.600 1

A

Selection tablesRCD-blocks DDA 70 and DDA 90 for MCBs S 290 series

DDA 70DDA 90

Y1 Y2 2 4/N

2/14/3(N)

Y1 Y2 2 4 6 8/N

2/14/3

6/58/7(N)

Y1 Y2 2 4/N

2/14/3(N)

Y1 Y2 2 4 6 8/N

2/14/3

6/58/7(N)


2CS

C40

0169

F020

12C

SC

4001

67F0

201

2CS

C40

0169

F020

12C

SC

4001

67F0

201


3/66 ABB

3

Technical featuresRCD-blocks for MCBs S800 series

DDA 800

TECHNICAL FEATURESStandards


Rated current In ARated sensitivity IΔn ARated voltage Ue VInsulation voltage Ui VMax. operating voltage of circuit test VMin. operating voltage of circuit test VRated frequency HzRated breaking capacity (Icn) acc. to IEC /EN 60947-2 ARated residual breaking capacity IΔm with S 800 N kA

with S 800 S kARated impulse withstand voltage (1.2/50) Uimp kVDielectric test voltage at ind. freq. for 1 min. kVSurge current resistance (wave 8/20) A




variable climatic conditions °C/RHAmbient temperature (with daily average ≤ +35 °C) °CStorage temperature °CTerminal size for cables flexible mm2

rigid mm2

Tightening torque N*mMounting

Dimensions Dimensions (H x D x W) 2P mmand weight 3P mm

4P mmWeight 2P g

3P g4P g

Combination Combinable with: S 800 Nwith MCBs S 800 S



3/67ABB

3

Technical featuresRCDs-blocks for MCBs S800 series

DDA 800System pro M compact®

DDA 800 AC DDA 800 A DDA 800 A AP-R DDA 800 A SIEC/EN 60947-2 Ann. B

AC A A A2P, 3P, 4P

63 63 100 63-100 63 1000.03-0.3 0.03-0.3-0.5 0.3-0.5 0.03 0.3-1 0.3-0.5*-1

230/400 - 240/415 - 400/690690690195

50...60according to the breaking capacity of the associated MCB

according to the Icu of the associated MCBaccording to the Icu of the associated MCB

62.5

250 3000 5000blue operating just from OFF position

1000020000IP4XIP2X

28 cycles with 55/95...10023/83 - 40/93 - 55/20

25/95 - 40/95-25...+60-40...+70

6...506...70

min. 3 / max. 4on DIN rail EN 60715 (35 mm) by means of rapid fixing device

108.2 x 82.3 x 81108.2 x 82.3 x 117108.2 x 82.3 x 117

300 for 63 A - 415 for 100 A400 for 63 A - 640 for 100 A460 for 63 A - 765 for 100 A

yesyes

* only on 3P and 4P versions


3/68 ABB

3


AC

Selection tablesRCD-blocks DDA 800 AC w type

DDA 800 AC

DDA 800 AC type for MCBs S800Function: RCD-block for assembly on site with MCBs S800 series up to 63 A. Protection against the effects of sinusoidal alternating earth fault currents; protection against indirect contacts and additional protection against direct (with IΔn=30 mA) contacts.


Standard: IEC/EN 60947-2 Ann. B


2 30 63 DDA802AC-63/0.03 2CSB802001R1630 919704 0.300 1

300 63 DDA802AC-63/0.3 2CSB802001R3630 919902 0.300 1

3 30 63 DDA803AC-63/0.03 2CSB803001R1630 922001 0.400 1

300 63 DDA803AC-63/0.3 2CSB803001R3630 922209 0.400 1

4 30 63 DDA804AC-63/0.03 2CSB804001R1630 924401 0.460 1

300 63 DDA804AC-63/0.3 2CSB804001R3630 924609 0.460 1

31

4/32/1

42

53

6/54/3

1

2/1

642

75

8/76/5

3

4/3

1

2/1

8642


2CS

C40

0177

F020

12C

SC

4001

78F0

201

2CS

C40

0179

F020

1


3/69ABB

3


A

Selection tablesRCD-blocks DDA 800 A y type

DDA 800 A

DDA 800 A type for MCBs S800Function: RCD-block for assembly on site with MCBs S800 up to 100 A. Protection against the effects of sinusoidal alternating and direct pulsating earth fault currents; protection against indirect contacts and additional protection against direct (with IΔn=30 mA) contacts.




2 30 63 DDA802 A-63/0.03 2CSB802101R1630 920007 0.300 1

300 63 DDA802 A-63/0.3 2CSB802101R3630 920205 0.300 1

100 DDA802 A-100/0.3 2CSB802101R3000 545033 0.415 1

500 63 DDA802 A-63/0.5 2CSB802101R4630 920403 0.300 1

100 DDA802 A-100/0.5 2CSB802101R4000 542636 0.415 1

3 30 63 DDA803 A-63/0.03 2CSB803101R1630 922308 0.400 1

300 63 DDA803 A-63/0.3 2CSB803101R3630 922506 0.400 1

100 DDA803 A-100/0.3 2CSB803101R3000 544135 0.640 1

500 63 DDA803 A-63/0.5 2CSB803101R4630 922704 0.400 1

100 DDA803 A-100/0.5 2CSB803101R4000 541738 0.640 1

4 30 63 DDA804 A-63/0.03 2CSB804101R1630 924807 0.460 1

300 63 DDA804 A-63/0.3 2CSB804101R3630 925002 0.460 1

100 DDA804 A-100/0.3 2CSB804101R3000 547532 0.765 1

500 63 DDA804 A-63/0.5 2CSB804101R4630 925200 0.460 1

100 DDA804 A-100/0.5 2CSB804101R4000 544937 0.765 1

31

4/32/1

42

53

6/54/3

1

2/1

642

75

8/76/5

3

4/3

1

2/1

8642


2CS

C40

0177

F020

12C

SC

4001

78F0

201

2CS

C40

0179

F020

1


3/70 ABB

3


A

Selection tablesRCD-blocks DDA 800 A y type AP-R (high immunity)

DDA 800 A AP-R

DDA 800 A AP-R type for MCBs S800Function: RCD-block for assembly on site with MCBs S800 up to 100 A. Protection against the ef-fects of sinusoidal alternating and direct pulsating earth fault currents, providing the best compromise between safety and continuity in the service thanks to the resistance to unwanted trippings; protection against indirect contacts and additional protection against direct (with IΔn=30 mA) contacts.




2 30 63 DDA802 A-63/0.03 AP-R 2CSB802401R1630 921400 0.300 1

100 DDA802 A-100/0.03 AP-R 2CSB802401R1000 544630 0.415 1

3 30 63 DDA803 A-63/0.03 AP-R 2CSB803401R1630 923800 0.400 1

100 DDA803 A-100/0.03 AP-R 2CSB803401R1000 542230 0.640 1

4 30 63 DDA804 A-63/0.03 AP-R 2CSB804401R1630 927709 0.460 1

100 DDA804 A-100/0.03 AP-R 2CSB804401R1000 547136 0.765 1

31

4/32/1

42

53

6/54/3

1

2/1

642

75

8/76/5

3

4/3

1

2/1

8642


2CS

C40

0177

F020

12C

SC

4001

78F0

201

2CS

C40

0179

F020

1


3/71ABB

3


DDA 800 A selective type for MCBs S800Function: RCD-block for assembly on site with MCBs S800 series up to 100 A. Protection against the effects of sinusoidal alternating and direct pulsating earth fault currents with an intentional trip-ping delay, which permits to realize the selectivity with downstream instantaneous devices (for more information about selectivity see the technical guide).




2 300 63 DDA802 A S-63/0.3 2CSB802201R3630 920601 0.300 1

100 DDA802 A S-100/0.3 2CSB802201R3000 542537 0.415

1000 63 DDA802 A S-63/1 2CSB802201R5630 920809 0.300 1

100 DDA802 A S-100/1 2CSB802201R5000 547433 0.415 1

3 300 63 DDA803 A S-63/0.3 2CSB803201R3630 922902 0.400 1

100 DDA803 A S-100/0.3 2CSB803201R3000 544838 0.640 1

500 100 DDA803 A S-100/0.5 2CSB803201R4000 542438 0.640 1

1000 63 DDA803 A S-63/1 2CSB803201R5630 923206 0.400 1

100 DDA803 A S-100/1 2CSB803201R5000 547334 0.640 1

3 300 63 DDA804 A S-63/0.3 2CSB804201R3630 926207 0.460 1

100 DDA804 A S-100/0.3 2CSB804201R3000 544739 0.765 1

500 100 DDA804 A S-100/0.5 2CSB804201R4000 542339 0.765 1

1000 63 DDA804 A S-63/1 2CSB804201R5630 926504 0.460 1

100 DDA804 A S-100/1 2CSB804201R5000 547235 0.765 1

Selection tablesRCD-blocks DDA 800 A y type selective

DDA 800 A S

A

31

4/32/1

42

53

6/54/3

1

2/1

642

75

8/76/5

3

4/3

1

2/1

8642


2CS

C40

0177

F020

12C

SC

4001

78F0

201

2CS

C40

0179

F020

1


3/72 ABB

3 TECHNICAL CHARACTERISTICS Standards

Electrical Operating characteristic: type (wave form of the earth leakage sensed) features Poles Rated sensitivity IΔn A Rated current In A Rated voltage Ue V Insulation voltage Ui V Max. operating voltage of circuit test V Min. operating voltage of circuit test V Rated frequency Hz Short-circuit breaking capacity 240/415 V kA ultimate Icu 254/440 V kA

acc. to IEC/EN 60947-2 289/500 V kA (AC) 50/60 Hz 400/690 V kA Short-circuit breaking capacity 240/415 V kA service Ics 254/440 V kA acc. to IEC/EN 60947-2 289/500 V kA (AC) 50/60 Hz 400/690 V kA

Rated impulse withstand voltage (1.2/50) Uimp kV Dielectric test voltage at ind. freq. for 1 min. kV Thermomagnetic release B: 3 In ≤ Im ≤ 5 In characteristic C: 5 In ≤ Im ≤ 10 In

D: 10 In ≤ Im ≤ 20 In K: 8 In ≤ Im ≤ 14 In Surge current resistance acc. to VDE 0432 Part 2 (wave 8/20) A Mechanical Toggle features Electrical life Mechanical life Protection degree housing terminals Tropicalization humid heat °C/RH acc. to IEC /EN 60068-2 constant climatic conditions °C/RH variable climatic conditions °C/RH Ambient temperature (with daily average ≤ + 35 °C) °C Storage temperature °C Installation Terminal size for cables flexible mm2 rigid mm2 Tightening torque N*m MountingDimensions Dimensions (H x D x W) 2P mm and weight 3P mm 4P mm Weight 2P g

3P g 4P g

Combination Combinable with: auxiliary contact with auxiliary signal contact/auxiliary switch elements shunt trip undervoltage release (*) 1A on 2P and 4P versions, while 0.3A only on 4P ones.




3/73ABB

3



DS800S A DS800N A DS800S A S DS800N A S DS800S A AP-R DS800N A AP-RIEC/EN 60947-2

A A A 2P, 3P, 4P 2P,4P 2P, 3P, 4P

0.3 0.3-1(*) 0.03125

230/400-240/415-400/690690690195

50…6050 36 50 36 50 3630 20 30 20 30 2010 10 10 10 10 104.5 4.5 4.5 4.5 4.5 4.540 30 40 30 40 3015 10 15 10 15 105 5 5 5 5 53 3 3 3 3 3

62.5

250 250 5000 5000 3000 3000black (MCB) sealable in ON-OFF position + blue (RCD) operating just from OFF position

1000020000IP4XIP2X

28 cycles with 55/95…10023/83 - 40/93 - 55/20

25/95 - 40/95-25…+60-40…+70

6…506…70

min. 3 / max. 4on DIN rail EN 60715 (35 mm) by means of rapid fi xing device

108,2 x 82,3 x 133.5108,2 x 82,3 x 196108,2 x 82,3 x 223

79011401440yesyesyesyes


3/74 ABB

3


2CC

C41

3257

F000

12C

CC

4132

58F0

001

2CC

C41

3259

F000

1

Selection tablesRCBOs DS800 series A y type

DS800S A

DS800S, A typeFunction: protection against overload and short-circuit currents; protection against the effects of sinusoidal alternating earth fault currents; protection against indirect contacts; command and isolation of resistive and inductive loads.



Icu=50 kA

Number Curve Rated Rated Order Bbn Price Price Weight Packof poles residual current details 7612271 1 piece group 1 piece unit current


2 B 300 125 DS802S-B125/0.3A 2CCA862005R0845 211721 0.790 1

C 300 125 DS802S-C125/0.3A 2CCA862005R0844 211738 0.790 1

D 300 125 DS802S-D125/0.3A 2CCA862005R0841 211745 0.790 1

K 300 125 DS802S-K125/0.3A 2CCA862005R0647 211752 0.790 1

3 B 300 125 DS803S-B125/0.3A 2CCA863005R0845 211769 1.14 1

C 300 125 DS803S-C125/0.3A 2CCA863005R0844 211776 1.14 1

D 300 125 DS803S-D125/0.3A 2CCA863005R0841 211783 1.14 1

K 300 125 DS803S-K125/0.3A 2CCA863005R0647 211790 1.14 1

4 B 300 125 DS804S-B125/0.3A 2CCA864005R0845 211806 1.44 1

C 300 125 DS804S-C125/0.3A 2CCA864005R0844 211813 1.44 1

D 300 125 DS804S-D125/0.3A 2CCA864005R0841 211820 1.44 1

K 300 125 DS804S-K125/0.3A 2CCA864005R0647 211837 1.44 1


5/63/4

6/54/3

1/2

2/1

3/41/2

4/32/1

7/85/6

8/76/5

3/4

4/3

1/2

2/1


3/75ABB

3


DS800N, A typeFunction: protection against overload and short-circuit currents; protection against the effects of sinusoidal alternating earth fault currents; protection against indirect contacts; command and isolation of resistive and inductive loads.



Icu=36 kA



2 B 300 125 DS802N-B125/0.3A 2CCA892005R0845 211844 0.790 1

C 300 125 DS802N-C125/0.3A 2CCA892005R0844 211851 0.790 1

D 300 125 DS802N-D125/0.3A 2CCA892005R0841 211868 0.790 1

3 B 300 125 DS803N-B125/0.3A 2CCA893005R0845 211875 1.14 1

C 300 125 DS803N-C125/0.3A 2CCA893005R0844 211882 1.14 1

D 300 125 DS803N-D125/0.3A 2CCA893005R0841 211899 1.14 1

4 B 300 125 DS804N-B125/0.3A 2CCA894005R0845 211905 1.44 1

C 300 125 DS804N-C125/0.3A 2CCA894005R0844 211912 1.44 1

D 300 125 DS804N-D125/0.3A 2CCA894005R0841 211929 1.44 1


DS800N ASystem pro M compact®

2CC

C41

3257

F000

12C

CC

4132

58F0

001

2CC

C41

3259

F000

1

7/85/6

8/76/5

3/4

4/3

1/2

2/1

5/63/4

6/54/3

1/2

2/1

3/41/2

4/32/1


3/76 ABB

3


Selection tablesRCBOs DS800 series A y type, selective

DS800S A S

DS800S, A selective typeFunction: protection against overload and short-circuit currents; protection against the effects of sinusoidal alternating earth fault currents with an intentional tripping delay, which allows to realize the selectivity with downstream instantaneous devices (for more information about selectivity see the technical guide); protection against indirect contacts; command and isolation of resistive and inductive loads.



Icu=50 kA



2 B 1000 125 DS802S-B125/1AS 2CCC862006R0845 211516 0.790 1

C 1000 125 DS802S-C125/1AS 2CCC862006R0844 211523 0.790 1

D 1000 125 DS802S-D125/1AS 2CCC862006R0841 211530 0.790 1

K 1000 125 DS802S-K125/1AS 2CCC862006R0647 211547 0.790 1

4 B 300 125 DS804S-B125/0.3AS 2CCC864005R0845 211554 1.44 1

1000 125 DS804S-B125/1AS 2CCC864006R0845 211592 1.44 1

C 300 125 DS804S-C125/0.3AS 2CCC864005R0844 211561 1.44 1

1000 125 DS804S-C125/1AS 2CCC864006R0844 211608 1.44 1

D 300 125 DS804S-D125/0.3AS 2CCC864005R0841 211578 1.44 1

1000 125 DS804S-D125/1AS 2CCC864006R0841 211615 1.44 1

K 300 125 DS804S-K125/0.3AS 2CCC864005R0647 211685 1.44 1

1000 125 DS804S-K125/1AS 2CCC864006R0647 211622 1:44 1


2CC

C41

3257

F000

12C

CC

4132

59F0

001

3/41/2

4/32/1

7/85/6

8/76/5

3/4

4/3

1/2

2/1


3/77ABB

3


DS800N, A selective typeFunction: protection against overload and short-circuit currents; protection against the effects of sinusoidal alternating earth fault currents with an intentional tripping delay, which allows to realize the selectivity with downstream instantaneous devices (for more information about selectivity see the technical guide); protection against indirect contacts; command and isolation of resistive and inductive loads.



Icu=36 kA



2 B 1000 125 DS802N-B125/1AS 2CCC892006R0845 211639 0.790 1

C 1000 125 DS802N-C125/1AS 2CCC892006R0844 211646 0.790 1

D 1000 125 DS802N-D125/1AS 2CCC892006R0841 211653 0.790 1

4 B 300 125 DS804N-B125/0.3AS 2CCC894005R0845 211660 1.44 1

1000 125 DS804N-B125/1AS 2CCC894006R0845 211691 1.44 1

C 300 125 DS804N-C125/0.3AS 2CCC894005R0844 211677 1.44 1

1000 125 DS804N-C125/1AS 2CCC894006R0844 211707 1.44 1

D 300 125 DS804N-D125/0.3AS 2CCC894005R0841 211684 1.44 1

1000 125 DS804N-D125/1AS 2CCC894006R0841 211714 1.44 1


DS800N A SSystem pro M compact®

2CC

C41

3257

F000

12C

CC

4132

59F0

001

7/85/6

8/76/5

3/4

4/3

1/2

2/1

3/41/2

4/32/1


3/78 ABB

3


Selection tablesRCBOs DS800 series A y type, AP-R (high immunity)

DS800S A AP-R

DS800S AP-R, A typeFunction: protection against the effects of sinusoidal alternating earth fault currents, providing the best compromise between safety and continuity in the service thanks to the resistance to unwanted trippings; protection against indirect contacts and additional protection against direct (IΔn=30 mA) contacts; protection and isolation of resistive and inductive loads.



Icu=50 kA



2 B 30 125 DS802SB125/.03AP-R 2CCB862004R0845 211301 0.790 1

C 30 125 DS802SC125/.03AP-R 2CCB862004R0844 211318 0.790 1

D 30 125 DS802SD125/.03AP-R 2CCB862004R0841 211325 0.790 1

K 30 125 DS802SK125/.03AP-R 2CCB862004R0647 211332 0.790 1

3 B 30 125 DS803SB125/.03AP-R 2CCB863004R0845 211349 1.14 1

C 30 125 DS803SC125/.03AP-R 2CCB863004R0844 211356 1.14 1

D 30 125 DS803SD125/.03AP-R 2CCB863004R0841 211363 1.14 1

K 30 125 DS803SK125/.03AP-R 2CCB863004R0647 211370 1.14 1

4 B 30 125 DS804SB125/.03AP-R 2CCB864004R0845 211387 1.44 1

C 30 125 DS804SC125/.03AP-R 2CCB864004R0844 211394 1.44 1

D 30 125 DS804SD125/.03AP-R 2CCB864004R0841 211400 1.44 1

K 30 125 DS804SK125/.03AP-R 2CCB864004R0647 211417 1,44 1


2CC

C41

3257

F000

12C

CC

4132

58F0

001

2CC

C41

3259

F000

1

5/63/4

6/54/3

1/2

2/1

3/41/2

4/32/1

7/85/6

8/76/5

3/4

4/3

1/2

2/1


3/79ABB

3


DS800N AP-R, A typeFunction: protection against the effects of sinusoidal alternating earth fault currents, providing the best compromise between safety and continuity in the service thanks to the resistance to unwanted trippings; protection against indirect contacts and additional protection against direct (IΔn=30 mA) contacts; protection and isolation of resistive and inductive loads.



Icu=36 kA



2 B 30 125 DS802NB125/.03AP-R 2CCB892004R0845 211424 0.790 1

C 30 125 DS802NC125/.03AP-R 2CCB892004R0844 211431 0.790 1

D 30 125 DS802ND125/.03AP-R 2CCB892004R0841 211448 0.790 1

3 B 30 125 DS803NB125/.03AP-R 2CCB893004R0845 211455 1.14 1

C 30 125 DS803NC125/.03AP-R 2CCB893004R0844 211462 1.14 1

D 30 125 DS803ND125/.03AP-R 2CCB893004R0841 211479 1.14 1

4 B 30 125 DS804NB125/.03AP-R 2CCB894004R0845 211486 1.44 1

C 30 125 DS804NC125/.03AP-R 2CCB894004R0844 211493 1.44 1

D 30 125 DS804ND125/.03AP-R 2CCB894004R0841 211509 1.44 1

Selection tablesRCBOs DS800 series A y type, AP-R (high immunity)

DS800N A AP-RSystem pro M compact®

2CC

C41

3257

F000

12C

CC

4132

58F0

001

2CC

C41

3259

F000

1

7/85/6

8/76/5

3/4

4/3

1/2

2/1

5/63/4

6/54/3

1/2

2/1

3/41/2

4/32/1


3/80 ABB

3TECHNICAL CHARACTERISTICSStandards


Rated current In ARated sensitivity IΔn ARated voltage Ue VInsulation voltage UiMax. operating voltage VMin. operating voltage VRated frequency HzRated breaking capacity acc. to IEC/EN 61009 ultimate Icn ARated breaking capacity ultimate Icu kAacc. to IEC/EN 60947-2 1P+N @230 VAC, 2P, 3P, 4P @400 VAC service Ics kARated residual breaking capacity IΔm kARated impulse withstand voltage (1.2/50) Uimp kVDielectric test voltage at ind. freq. for 1 min. kVThermomagnetic release B: 3 In ≤ Im ≤ 5 Incharacteristic C: 5 In ≤ Im ≤ 10 InSurge current resistance (wave 8/20) A




variable climatic conditions °C/RHReference temperature for setting of thermal element °CAmbient temperature (with daily average ≤ +35 °C) °CStorage temperature °C


Terminal size top/bottom for cables 1P+N mm2

line side mm2

load side mm2

Tightening torque top/bottom 1P+N N*mMounting

Dimensions Dimensions (H x D x W) 1P+N mmand weight Weight 1P+N gCombination Combinable with: auxiliary contactwith auxiliary signal contactelements shunt trip



DS 271System pro M compact®


3/81ABB

3


DS 271

DS 271 AC DS 271 AIEC 61009, BSEN 61009-2-2

AC A1P+N

6 ≤ In ≤ 400.01-0.03-0.1-0.3 0.01-0.03-0.1-0.3

230-24050025485

50…6010000

-7.565

2.5

250black sealable in on-off position

1000020000IP4XIP2X

28 cycles with 55/95…10023/83 - 40/93 - 55/20

25/95 - 40/9530

-25…+55-25…+70

cage (shock protected)cage (shock protected)

-L1: 1up to 25; N: flexible 4; FE: flexible 0.5

L1 and N: 1 up to 102 top; 1.2 bottom

on DIN rail EN 60715 (35 mm) by means of fast clip device120 x 67.6 x 17.5

205nononono


3/82 ABB

3


DS 271 AC type, B and C characteristicsFunction: protection against overload and short-circuit currents; protection against the effects of si-nusoidal alternating earth fault currents; protection against indirect contacts and additional protection against direct contacts (IΔn=30 mA).


Standard: IEC 61009, BSEN61009-2-2

Icn=10 kA

Character Rated Rated Order Bbn Price Price Weight Packistics/ residual current details 8012542 1 piece group 1 piece unitCurve current IΔn mA In A Type code Order code EAN kg pc.

B 10 6 DS271 AC-B6/0.01 ELN 2CSR175092R0065 036753 0.205 1

10 DS271 AC-B10/0.01 ELN 2CSR175092R0105 036852 0.205 1

16 DS271 AC-B16/0.01 ELN 2CSR175092R0165 036951 0.205 1

20 DS271 AC-B20/0.01 ELN 2CSR175092R0205 037057 0.205 1

25 DS271 AC-B25/0.01 ELN 2CSR175092R0255 037156 0.205 1

32 DS271 AC-B32/0.01 ELN 2CSR175092R0325 037255 0.205 1

30 6 DS271 AC-B6/0.03 ELN 2CSR175092R1065 037354 0.205 1

10 DS271 AC-B10/0.03 ELN 2CSR175092R1105 037453 0.205 1

16 DS271 AC-B16/0.03 ELN 2CSR175092R1165 037552 0.205 1

20 DS271 AC-B20/0.03 ELN 2CSR175092R1205 037651 0.205 1

25 DS271 AC-B25/0.03 ELN 2CSR175092R1255 037750 0.205 1

32 DS271 AC-B32/0.03 ELN 2CSR175092R1325 037859 0.205 1/20

C 10 6 DS271 AC-C6/0.01 ELN 2CSR175092R0064 038559 0.205 1

10 DS271 AC-C10/0.01 ELN 2CSR175092R0104 038658 0.205 1

16 DS271 AC-C16/0.01 ELN 2CSR175092R0164 038757 0.205 1/20

20 DS271 AC-C20/0.01 ELN 2CSR175092R0204 038856 0.205 1

25 DS271 AC-C25/0.01 ELN 2CSR175092R0254 038955 0.205 1

32 DS271 AC-C32/0.01 ELN 2CSR175092R0324 039051 0.205 1/20

30 6 DS271 AC-C6/0.03 ELN 2CSR175092R1064 039150 0.205 1

10 DS271 AC-C10/0.03 ELN 2CSR175092R1104 039259 0.205 1

16 DS271 AC-C16/0.03 ELN 2CSR175092R1164 039358 0.205 1

20 DS271 AC-C20/0.03 ELN 2CSR175092R1204 039457 0.205 1

25 DS271 AC-C25/0.03 ELN 2CSR175092R1254 039556 0.205 1

32 DS271 AC-C32/0.03 ELN 2CSR175092R1324 039655 0.205 1

40 DS271 AC-C40/0.03 ELN 2CSR175092R1404 128755 0.205 1

100 6 DS271 AC-C6/0.1 ELN 2CSR175092R2064 039754 0.205 1

10 DS271 AC-C10/0.1 ELN 2CSR175092R2104 039853 0.205 1/20

16 DS271 AC-C16/0.1 ELN 2CSR175092R2164 039952 0.205 1/20

20 DS271 AC-C20/0.1 ELN 2CSR175092R2204 040057 0.205 1/20

25 DS271 AC-C25/0.1 ELN 2CSR175092R2254 040156 0.205 1

32 DS271 AC-C32/0.1 ELN 2CSR175092R2324 040255 0.205 1

300 6 DS271 AC-C6/0.3 ELN 2CSR175092R3064 040354 0.205 1

10 DS271 AC-C10/0.3 ELN 2CSR175092R3104 040453 0.205 1

16 DS271 AC-C16/0.3 ELN 2CSR175092R3164 040552 0.205 1

20 DS271 AC-C20/0.3 ELN 2CSR175092R3204 040651 0.205 1

25 DS271 AC-C25/0.3 ELN 2CSR175092R3254 040750 0.205 1

32 DS271 AC-C32/0.3 ELN 2CSR175092R3324 040859 0.205 1

40 DS271 AC-C40/0.3 ELN 2CSR175092R3404 128854 0.205 1

B

Selection tablesRCBOs DS 271 series 10000 AC w type

DS 271 AC B DS 271 AC C

C

2CS

C40

0407

F020

12C

SC

4004

07F0

201



3/83ABB

3


DS 271 A type, B and C characteristicsFunction: protection against overload and short-circuit currents; protection against the effects of sinusoidal alternating and direct pulsating earth fault currents; protection against indirect contacts and additional protection against direct contacts (IΔn=30 mA).


Standard: IEC 61009, BSEN61009-2-2

Icn=10 kA

Character Rated Rated Order Bbn Price Price Weight Packistics/ residual current details 8012542 1 piece group 1 piece unitCurve current IΔn mA In A Type code Order code EAN kg pc.

B 10 6 DS271 A-B6/0.01 ELN 2CSR175192R0065 032557 0.205 1

10 DS271 A-B10/0.01 ELN 2CSR175192R0105 032656 0.205 1

16 DS271 A-B16/0.01 ELN 2CSR175192R0165 032755 0.205 1

20 DS271 A-B20/0.01 ELN 2CSR175192R0205 032854 0.205 1

25 DS271 A-B25/0.01 ELN 2CSR175192R0255 032953 0.205 1

32 DS271 A-B32/0.01 ELN 2CSR175192R0325 033059 0.205 1

30 6 DS271 A-B6/0.03 ELN 2CSR175192R1065 033158 0.205 1

10 DS271 A-B10/0.03 ELN 2CSR175192R1105 033257 0.205 1

16 DS271 A-B16/0.03 ELN 2CSR175192R1165 033356 0.205 1

20 DS271 A-B20/0.03 ELN 2CSR175192R1205 033455 0.205 1

25 DS271 A-B25/0.03 ELN 2CSR175192R1255 033554 0.205 1

32 DS271 A-B32/0.03 ELN 2CSR175192R1325 033653 0.205 1

C 10 6 DS271 A-C6/0.01 ELN 2CSR175192R0064 034353 0.205 1

10 DS271 A-C10/0.01 ELN 2CSR175192R0104 034452 0.205 1

16 DS271 A-C16/0.01 ELN 2CSR175192R0164 034551 0.205 1

20 DS271 A-C20/0.01 ELN 2CSR175192R0204 034650 0.205 1

25 DS271 A-C25/0.01 ELN 2CSR175192R0254 034759 0.205 1

32 DS271 A-C32/0.01 ELN 2CSR175192R0324 034858 0.205 1

30 6 DS271 A-C6/0.03 ELN 2CSR175192R1064 034957 0.205 1

10 DS271 A-C10/0.03 ELN 2CSR175192R1104 035053 0.205 1/20

16 DS271 A-C16/0.03 ELN 2CSR175192R1164 035152 0.205 1/20

20 DS271 A-C20/0.03 ELN 2CSR175192R1204 035251 0.205 1/20

25 DS271 A-C25/0.03 ELN 2CSR175192R1254 035350 0.205 1

32 DS271 A-C32/0.03 ELN 2CSR175192R1324 035459 0.205 1

40 DS271 A-C40/0.03 ELN 2CSR175192R1404 128557 0.205 1

100 6 DS271 A-C6/0.1 ELN 2CSR175192R2064 035558 0.205 1

10 DS271 A-C10/0.1 ELN 2CSR175192R2104 035657 0.205 1

16 DS271 A-C16/0.1 ELN 2CSR175192R2164 035756 0.205 1

20 DS271 A-C20/0.1 ELN 2CSR175192R2204 035855 0.205 1

25 DS271 A-C25/0.1 ELN 2CSR175192R2254 035954 0.205 1

32 DS271 A-C32/0.1 ELN 2CSR175192R2324 036050 0.205 1

300 6 DS271 A-C6/0.3 ELN 2CSR175192R3064 036159 0.205 1

10 DS271 A-C10/0.3 ELN 2CSR175192R3104 036258 0.205 1

16 DS271 A-C16/0.3 ELN 2CSR175192R3164 036357 0.205 1

20 DS271 A-C20/0.3 ELN 2CSR175192R3204 036456 0.205 1

25 DS271 A-C25/0.3 ELN 2CSR175192R3254 036555 0.205 1

32 DS271 A-C32/0.3 ELN 2CSR175192R3324 036654 0.205 1

40 DS271 A-C40/0.3 ELN 2CSR175192R3404 128656 0.205 1

Selection tablesRCBOs DS 271 series 10000 A y type

DS 271 A B DS 271 A C

B

C

2CS

C40

0407

F020

12C

SC

4004

07F0

201



3/84 ABB

3


Residual current relays with external toroidal transformer can detect leakage currents. Through minidip you can set sensitivity and intervention time.

RD2 residual current relays

Operating Order Bbn Price Price Weight Packvoltage details 8012542 1 piece group 1 piece unit V Type code Order code EAN kg pc.

230…400 a.c. RD2 2CSM142120R1201 058007 0.125 1

48…150 a.c./d.c. RD2-48 2CSM242120R1201 537809 0.125 1

Technical featuresOperating voltage [V] 230÷400 a.c. (RD2) and 48÷150 a.c./d.c. (RD2-48)Type AFrequency [Hz] 50÷60Sensitivity settings IΔn [A] 0.03; 0.1; 0.3; 0.5; 1; 2Intervention time [s] Fast (instantaneous); 0.3; 0.5; 1; 2; 5settings Contact capacity [A] 10 at 250 V a.c. (ohmic)Contact type NC-C-NOOperating temperature [°C] -5…+40Modules [No.] 2Standards IEC/EN 62020

IndicationsGreen LED: supply voltage present Red LED: alarm status

More functionsThe connection between the toroidal transformer and the residual current relay is continually che-cked by the relay; if the connection interrupts, the residual current relay enters the “alarm” status. The ”test” pushbutton simulates - internally to the RD2 - the residual current conditions for the RD2 to operate. If pushed, the RD2 must enter the alarm status. The “reset” pushbutton allows the residual current relay to return to the starting condition.

If the configuration is not appropriate, the de-vice will automatically consider as valid the first configuration (according to the diagram) and enter the maximum safety.O

EP

M02

95

0.03 0.1 0.3 0.5 1 2

Fast 0.3 0.5 1 2 5

0.03

IΔn(A)

0.1

0.3

0.5

1

2

Fast

Time(sec.)

0.3

0.5

1

2

5

Selection of calibration

2CS

C40

0320

F020

1

Selection tablesRD2 residual current relays

RD2System pro M compact®

For reference only.www.fengshengelectric.com.sg

3/85ABB

3


RD3 residual current relaysThe RD3 family of electronic residual current relays provides residual current protection and monito-ring functions according to IEC/EN 60947-2:2006 annex M and can be used in conjunction with all S 200 automatic devices and Tmax range moulded case devices up to T5, for industrial installations.

The RD3 residual current relays can provide status indications through two output contacts.


12-48 a.c./d.c. RD3-48 2CSJ201001R0001 748236 0.13 1

230-400 a.c. RD3 2CSJ201001R0002 734833 0.25 1

12-48 a.c./d.c. RD3M-48 2CSJ202001R0001 733935 0.13 1

230-400 a.c. RD3M 2CSJ202001R0002 747031 0.25 1

12-48 a.c./d.c. RD3P-48 2CSJ203001R0001 734734 0.13 1

230-400 a.c. RD3P 2CSJ203001R0002 733836 0.25 1

Technical features RD3/RD3-48 RD3M/RD3M-48 RD3P/RD3P-48

Operating voltage RD3: 230-400 Vac +10% / -15% RD3M: 230-400 Vac +10% / -15% RD3P: 230-400 Vac +10% / -15%

RD3-48: 12-48 Vac/Vdc +10% / -15% RD3M-48: 12-48 Vac/Vdc +10% / -15% RD3P-48: 12-48 Vac/Vdc +10% / -15%

Auxiliary supply frequency 50-60 Hz 50-60 Hz 50-60 Hz

Network monitored frequency 50 Hz -150 Hz* 50 Hz -150 Hz* 50 Hz -150 Hz*

Frequency filter - 150 Hz fT = 400 Hz 150 Hz fT = 400 Hz

Type A (up to IΔn=5 A), A (up to IΔn=5 A) A (up to IΔn=5 A) AC (for higher current) AC (for higher current) AC (for higher current)

Operating temperature -25….+70 °C -25….+70 °C -25….+70 °C

Maximum power consumption <3.6 W (RD3), <3.6W (RD3M), <3.6 W (RD3P), <600 mW (RD3-48) <600mW (RD3M-48) <600 mW (RD3P-48)

Sensitivity settings IΔn 0.03-0.1-0.3-0.5-1-2-3-5-10-30 0.03-0.1-0.3-0.5-1-2-3-5-10-30 0.03-0.1-0.3-0.5-1-2-3-5-10-30

Tripping time settings Δt 0-0.06-0.2-0.3-0.5-1-2-3-5-10 0-0.06-0.2-0.3-0.5-1-2-3-5-10 0-0.06-0.2-0.3-0.5-1-2-3-5-10

Pre-alarm threshold - 60% 60%

Max. resistance connection between toroidal transformer and relay 3 W 3 W 3 W

Max. length connection of remote reset button 15 m 15 m 15 m

Output Contact capacity (7-8-9); (10-11-12) 8 A, 250 V a.c. 8 A, 250 V a.c. 8 A, 250 V a.c.

Led bar indicator - - Yes

Max. cable terminals section 2.5 mm² 2.5 mm² 2.5 mm²

Modules 3 3 3

Dimensions 52.8 × 85 × 64.7 mm 52.8 × 85 × 64.7 mm 52.8 × 85 × 64.7 mm

Protection degree IP20 IP20 IP20

Standards IEC/EN 60947-2 annex. M IEC/EN 60947-2 annex. M IEC/EN 60947-2 annex. M

*RD3 can detect, as a monitor, sinusoidal earth fault currents in networks with frequencies between 50 Hz and 150 Hz.

2CS

C40

0691

F020

12C

SC

4006

90F0

201

2CS

C40

0689

F020

1

Selection tablesRD3 residual current relays

RD3System pro M compact®


3/86 ABB

3


RD front panel residual current relaysRD front panel residual current relays achieve their protective function in combination with an external toroidal transformer. You can set the sensitivity between 0.025 A and 25 A, the tripping time can vary from 0.02 to 5 seconds.

Residual current relays are available in 48 mm x 48 mm, 72 mm x 72 mm and 96 mm x 96 mm versions.

The RD296 version is provided of dip switch to select the fail safe function (the output contacts will switch both for differential current over the threshold that for the lack of input current). The RD296-S is provided of fail safe function and memory led. The RD296-DIG version is provided of fail safe function (as the precedent). The digital display allows the visualization of differential current IΔn.


24, 48 V a.c./V d.c. RD148-24 2CSG452211R1201 540908 0.112 1

115 V a.c./ d.c., 230 V a.c. RD148-230 2CSG252211R1201 541004 0.112 1

24, 48 V a.c./V d.c. RD172-24 2CSG452120R1201 747406 0.322 1

115 V a.c./ d.c., 230 V a.c. RD172-230 2CSG252120R1201 747505 0.322 1

24, 48 V a.c./V d.c. RD272-24 2CSG452424R1201 742302 0.322 1

115 V a.c./V d.c RD272-115 2CSG352424R1201 742401 0.322 1

115, 230, 400 V a.c. RD272-230 2CSG152424R1201 742500 0.322 1

24, 48 V a.c./V d.c. RD196-24 2CSG452130R1201 541103 0.383 1

115 V a.c./ d.c. and 230, 400 V a.c. RD196-230 2CSG252130R1201 541202 0.383 1

24, 48, 115 V a.c./ V d.c. RD296-24 2CSG452434R1201 541301 0.383 1

115 V a.c./ V d.c. RD296-115 2CSG352434R1201 742906 0.383 1

115 V a.c./ V d.c. and 230, 400 V a.c. RD296-230 2CSG152434R1201 541400 0.383 1

24, 48, 115 V a.c./ V d.c. RD296-S-24 2CSG452435R1201 541509 0.383 1

115 V a.c./ V d.c. RD296-S-115 2CSG352435R1201 743002 0.383 1

115 V a.c./ V d.c. and 230, 400 V a.c. RD296-S-230 2CSG152435R1201 541608 0.383 1

24, 48 V a.c./ V d.c. RD296-DIG-24 2CSG452436R1201 743101 0.383 1

115 V a.c./V d.c. RD296-DIG-115 2CSG352436R1201 743200 0.383 1

115, 230, 400 V a.c. RD296-DIG-230 2CSG152436R1201 743309 0.383 1

Technical featuresRD148 RD172 RD272 RD196 RD296 RD296-S

RD296-DIGType A A A A A AOperating voltage [V] 24, 48,

115, 230 a.c./ 24, 48, 115 d.c.

24, 48, 115, 230 a.c./

24, 48, 115 d.c.

24, 48, 115 230, 400 a.c./

24, 48, 115 d.c.

24, 48, 115, 230, 400 a.c./

24, 48, 115 d.c.

24, 48, 115, 230, 400 a.c./

24, 48, 115 d.c.

24, 48, 115, 230, 400 a.c./

24, 48, 115 d.c.Operating frequency [Hz] 50 – 60 50 – 60 50 – 60 50 – 60 50 – 60 50 – 60Current tripping thresholds IΔn [A] from 0.025 to 25 from 0.025 to 25 from 0.025 to 25 from 0.025 to 25 from 0.025 to 25 from 0.025 to 25 (S)

from 0.03 to 30 (DIG)Tripping times [sec.] from 0.02 to 5 from 0.02 to 5 from 0.02 to 5 from 0.02 to 5 from 0.02 to 5 from 0.02 to 5Number of contacts [No.] 2 1 2 1 2 2Contact capacity [A] 5 (250 V a.c.) 5 (250 V a.c.) 5 (250 V a.c.) 5 (250 V a.c.) 5 (250 V a.c.) 5 (250 V a.c.)Contact type change over change over change over change over change over change overWorking temperature [°C] -10…+60 -10…+60 -10…+60 -10…+60 -10…+60 -10…+60Storage temperature [°C] -10…+70 -10…+70 -10…+70 -10…+70 -10…+70 -10…+70Dissipated power [W] 7 max. 7 max. 7 max. 7 max. 7 max. 7 max.Dimensions W x H [mm] 48 x 48 72 x 72 72 x 72 96 x 96 96 x 96 96 x 96Display - - - - - yesApplicable standards EN 62020

IEC 62020EN 62020 IEC 62020

EN 62020 IEC 62020

EN 62020 IEC 62020

EN 62020 IEC 62020

EN 62020 IEC 62020

2CS

C40

5060

F000

12C

SC

4051

60F0

001

2CS

C40

5061

F000

12C

SC

4006

92F0

201

Selection tablesFront panel residual current relays

RDSystem pro M compact®


3/87ABB

3


Toroidal transformers

Dimension Ø Order Bbn Price Price Weight Pack details 8012542 1 piece group 1 piece unit mm Type code Order code EAN kg pc.

29 (modular version) TRM 2CSM029000R1211 020707 0.170 1

35 TR1 2CSG035100R1211 020301 0.212 1

60 TR2 2CSG060100R1211 020400 0.274 1

80 TR3 2CSG080100R1211 020509 0.454 1

110 TR4 2CSG110100R1211 020608 0.530 1

110 (openable version) TR4/A 2CSG110200R1211 743408 0.600 1

160 TR160 2CSG160100R1211 743507 1.350 1

160 (openable version) TR160A 2CSG160200R1211 743606 1.600 1

210 TR5 2CSG210100R1211 024804 1.534 1

210 (openable version) TR5/A 2CSG210200R1211 065708 1.856 1

2CS

C40

0494

F020

1

Selection tablesToroidal transformers

TRSystem pro M compact®


Residual current devices - Seen Joo

Documents

Transcript of Residual current devices - Seen Joo