r-l(ez'--r (EINATIONAL ENERGY FTEGULATOR OF SOTJTH AFRICA

Registration Certificate Number: GARE lT 113412020

CERTIFICATE FOR THE REGISTRATION OF OPERATION OF GAS

TRANSMISSION ACTIVITIES FOR OWN USE

This registration certificate is issued by the National Energy Regulator of South

Africa, hereinafter referred to as "NERSA", in terms section 28 of the Gas Act,

2001 (Act No. 48 of 2001) ("the Gas Act"). This certificate is issued to:

CERAMIC INDUSTRIES PTY LTD

(Company Registration No: 1 982/008520/07)

herein after referred to as "the Registrant", only for the purpose of operating gas

transmission activities for own use in the Vereeniging area of the Emfuleni

Local Municipality in the Gauteng province.

The registration under this certificate is subject to the requirements of the Gas

Act as stipulated in the Addendum hereto. The Registrant must comply with

these requirements.

ISSUED at Pretoria on this the day of 2020

NOMALANGA SITHOLE

ACTING CHIEF EXECUTIVE OFFICERSEAL

(EE_ HNATIONAL ENERGY REGULATOR OF SOUTH AFRICA

CONDITIONS FOR THE REGISTRATION OF OPERATION OF GAS

TRANSMISSION ACTIVITIES FOR OWN USE

TABLE OF CONTENTS

DEFINTTIONS ........... .......3

CHAPTER ONE: REGISTERED ACTIVITY.......... ..........4

CHAPTER TWO: GENERAL CONDITIONS........... ........7

Page 1 of 14

Annexure A:

Annexure B:

Annexure C:

Annexure D:

Map of the proposed pipeline

Block diagram

Mechanical flow diagram PRS

Standards

Page 2 ot 14

DEFINITIONS

ln these registration conditions any word or expression to which a meaning has

been assigned in the Act shall have the meaning so assigned, unless the

context indicates otherwise.

"authorised person" means any person holding a valid authorisation permit

as defined by Rule.

"the Gas Act" means the Gas Act, 2001 (Act No. 48 of 2001).

'nRules" means Rules made by the NERSA in terms of section 34(3) of the Gas

Act and Rule has a corresponding meaning (Rule 19).

"Regulations" means regulations made in terms of section 34 of the Gas Act.

Page 3 ot 14

REGISTERED ACTIVITY

1 Registered Operation

NERSA has registered Ceramic lndustries (Pty) Ltd's operation of gas

transmission facility for own use in the Vereeniging area of the Emfuleni

Local Municipality in the Gauteng province as indicated in Annexure A.

1.1

1.2 Table 1 below provides coordinates of Ceramic lndustries' transmission

pipeline from Sasol Gas tie point to high pressure customer meter station

(HPCMS).

Table 1: Coordinates of Ceramic lndustries' transmission pipeline from

Sasol Gas tie point to HPCMS.

PI COORDINATES LIST

PT Y.

COORDINATES

x-

COORDINATES

Latitude Longitude

Ceramic lndustries HPCMS lnlet

Pt 0 -85 304.75 2 946135.06 "26'37',22.50153" S "27"51'.23.73635" E

Points along pipeline

Pt 1 -85 302.71 2 946 144.07 "26'37',22.79469" S "27"51',23.66479" E

Pt2 -85 091.29 2 946 095.26 "26'37',21.25491" S "27"51'16.01092" E

Pl 3 -85 057.67 2 946 260.60 "26"37'26.63378" S "27"51'.14.83561" E

Pt4 -84 997.48 2 946 249.82 "26'37',26.29662" S "27"51'12.65733 E

Pt 5 -84 993.35 2 946 421.48 "26"37',31.87442" S "27"51',12.54947" E

Pt 6 -85 002.74 2946 518.47 "26'37'35.02339" S "27"51',12.91231" E

P17 -85 004.21 2 946 580.22 "26"37',37.02921" S "27"51',12.98035" E

P1 I -84 968.50 2947 253.27 "26'37',58.90302" S "27'51'11.85193" E

P1 I -84 906.36 2 948 561.78 "26"38',41.42735" S "27"51',09.92128" E

P1 10 -85 996.2'1 2 948 561 .78 "26'38',41.45334" S "27"51''13.16999" E

P1 11 -85 021.28 2948 672.56 "26'38',45.00143" s "27"51',14.10279 E

P1 12 -85 041.33 2 948 717.02 "26'38',46.44148" S "27"51',14.83841" E

P1 13 -84 904.79 2 948 783.01 "26038',48.61500" S "27"51',09.91791" E

P1 14 -85 004.67 2 948 956.00 "26'38',54.21341" S "27'51',13.57076" E

P1 15 -85 085.57 2 949 061.93 "26038'57.63728" S "27"51'16.52128" E

Page 4 ot 14

P1 16 -85 094.01 2 949 096.23 "26039'58.74979" S '27'51',16.83473" E

P1 17 -85 070.61 2 949 121.12 "26'38'59.56350" S "27"51',15.99472" E

P1 18 -84 953.27 2949180.87 "26'39'01 .53013" S "27"51',11.76674" E

P1 19 -84 876.21 2949195.40 "26"39'02.01893" S "27"51'08.97943" E

P120 -84 873.66 2 949 265.75 "26"39'04.30498" S "27"51',08.90991" E

P1 21 -84 845.08 2 949 373.65 "26"39'07.81662" S "27"51'07.90162" E

Pl 22 -84760.79 2 949 539.85 "26039'14.01385" S "27"51',04.88616" E

P1 23 -84 702.79 2 949 539.85 "26039'13.24694" S "27"51'02.79706" E

Pl 24 -85 644.11 2 949 697.90 "26'39',18.39435" S "27"51'00.71346" E

Pl 25 -85 644.11 2 949 798.23 "26"39',21.65387" S "27'51'00.73761" E

Sasol Gas tie point

P1 25 -84154.59 2 950 152.29 "26'39',33.26213""S "27"50',43.12283" E

1.3

1.4

This registration is granted to the registrant to operate the gas

transmission facilities, as indicated in Annexure A and B.

This registration only applies to gas conforming to the gas combustion

specifications as set out in table 2 below.

Table 2: Gas Combustion Specifications

1.5 The entire list of the standards that Ceramic lndustries plans to abide by

when constructing the transmission facility is attached in the registration

conditions as Annexure D.

1.6 Table 3 below specifications of the gas transmission facility.

Element ConditionsEnergy content MJ/m3 (110,3 kPa (a) OoC 41,3 (t6o/o)

MJ/m3Gross content MJ/m3n (101,325 kPa (a) 15 oC 39 (t6%) MJ/m3nRelative density 0,56 - 0,70Wobbe lndex (Wl) 101,325 kPa (a) 15 oC 48,1 - 52,2Sulphur (S) 15 mg m3n (max)

Page 5 of 14

Value

Table 3: S ifications of the transmission facility

1.7 The Registrant may not transfer ownership of the registered gas

production operation to another party without the approval of NERSA.

1.8 ln addition to the above the registrant must comply with all the

conditions that are specified in the construction licence of a gas

transmission facility (Gala.t. F1 116981201 9). Furthermore, the registrant

must carry out the gas transmission activities in a manner consistent

with the objectives and provisions of the Act and must comply with all

codes and standards used for operating gas transmission pipeline.

2. Duration of the Certificate

2.1 The certificate is valid for an indefinite period from the date of issue,

until such time that the operations are terminated or discontinued for

whatever reasons.

Page 6 of 14

GENERAL REQUIREMENTS

3. Monitoring and Provision of lnformation

3.1 ln terms of regulation 9 of the Piped Gas Regulations, the Registrant

must provide NERSA with the following information within three months

of the end of each calendar year:

a) The actual and planned gas production quantities;

b) The specification details of the gas produced;

c) Gas intended for own exclusive use; and

d) The gas reserves data measured in trillion cubic feet (tcf).

3.2 The Registrant must notify NERSA in writing if during a calendar year

there is a substantial change in the information to be provided under

regulation 9 of the Piped-Gas Regulations.

3.3 ln terms of section 28(2) of the Gas Act, the Registrant must provide

NERSA with such information concerning the activities of the operation

as may be prescribed.

4. Compliance

4.1 This certificate is granted only in terms of section 28 of the Gas Act and

for the activities specified and described in paragraph 1.1 above. This

certificate does not exempt the Registrant from compliance with any

other legislation.

5. Changes in Registrant's Particulars

5.1 The Registrant must at all times provide NERSA with the details of any

changes in the registered name, operating or trading name, registered

address and other contact details, including but not limited to, the names,

telephone numbers, facsimile numbers and email addresses of contact

persons.

Page 7 ol14

5.2 The notifications contemplated in paragraph 5.1 above must be provided

within fourteen (14) days of the event giving rise to them.

6. Correspondence with NERSA

6.1 All official communication by the Registrant with NERSA must be in

writing, signed and addressed to NERSA.

6.2 The Registrant must in all correspondence with NERSA quote the

registration reference number as it appears on this certificate.

Page 8 of 14

9t to 6 o6Ed

o

=(,o,'at,oooaoCL

o

oCLG

=<UJtfxlrJzz

vt to oI o6ed

EGLo).gEl<oo6moLxo

Annexure C: Mechanical diagram HPCMS

$

o

oo)(EIL

Annexure D: Standards

List all application:a. Legislation

i. OHS- act and regulations - construction regulation, Pressure EquipmentRegulations (and Ceramic lndustries /SANS Standards) Major Hazardous,I nstallation Regulation.

ii. Gas Act Regulation and Rulesiii. Municipal bylaw and proceduresiv. EIA Regulation

b. Codes and specifications, including those related to safety to be used forthe activities applied for ASME, API EN etc.

i. General - The pipeline facility shall comply with prevailing legislationapplicable to the planning design construction, testing, commissioning andoperation of pipelines in the RSA SANS 347. The latest editions of all codesand standards, including revisions and addenda, shall be applied.

ii. Primary Code - The primary codes for the design, construction, testing,commissioning and operation of operation of the pipeline facilities shall be;

1. ASME B31.8-2014 Gas Transmission and distribution piping system2. ASME 831.3-2016 Process piping

iii. Supplementary Codes & Standards

1. API 5L: Specification for Line Pipe2. AP! 6D: Specification for Pipeline Valves3. API 6FA: Fire Test for Valves4. API 1102: Steel Pipelines Crossing Railroads and Highways

5. API 1104: Standards for Welding Pipeline and Related Facilities

6. ASCE 7-98: Minimum Design Loads for Buildings and other structures7. ASME 816.5: Pipe Flanges and Flanged fittings8. ASME 816.4a: Valve-Flanged, Threaded, and Welding End

9. NACE RP0169-96: Control of external corrosion and underground or

submerged metallic piping systems.10. NACE RP0268: Electrical lsolation of cathodically protected pipelines.

11. NACE RP0572: Design, installation, operation, and maintenance ofimpressed current deep ground beds.

12. PRCI: lnstallation of pipelines by horizontal directional drilling

Page 12ot 14

General Sasol Gas'Codes and Standards used in qas pipelines

41: Codes1. ASME B31.8: 2010 - Gas transmission and distribution systems;2. B31.8S - 2012 - Managing System lntegrity of Gas Pipelines;3. NACE RP 0169 - Control External Corrosion of underground;4. API RP 2201 - Safe Hot Tapping Practices in the Petroleum and

Petrochemical I ndustries;5. ASME Vlll Div 1'. Required applicable to the design, fabrication,

inspection, testing, and certification of pressure vessels;6. ASME/ANSI 831.1 - Requirements for materials and components,

design, fabrication, assembly, erection, examinations, inspection andtesting of piping;

7. API RP 520 - Sizing and selection of pressure relief devices;8. NFPA 59A - Codes, standards, research, training and education on fire

hazards;

A2: National Standards1. SANS 10268-2:2004 - Welding of Thermoplastics - Welding Processes

Parl2: Electro fusion Welding;2. SANS 10269:2009 - Welding of thermoplastics - Testing and approval

of welders;3. SANS 1027O:2011 - Welding of Thermoplastics - Approval of Welding

procedures and welds;4. SANS 347:2010 - Categorisation and Conformity Assessment Criteria

for all Pressure Equipment;5. SANS 10227:2007 - Criteria for the Operation of lnspection Authorities

Performing lnspection in Terms of the Pressure Equipment Regulations;6. SANS 0121 - Cathodic Protection of buried and submerged structures;

and7. SANS 12OO

8. SANS 329:2007 Edition 1 - lndustrial Thermo Processing Equipment.

B: Customer Meter Stations (CMS)

81. Codes1. ASME B31.8:2010 - Gas transmission and distribution systems2. B31.8S -2012 - Managing System lntegrity of Gas Pipelines

3. ASME 816.5 - Pipe flanges and flanged Fittings4. ASME 836.1M -2004, Welded and Seamless Wrought Steel Pipe

5. ASME 816.9-2007 - Factory Made Wrought Butt welding Fittings

6. ASME 816.25 - Butt welding Ends7. ASME B16.11 - Forged Fittings, Socket-welding and threaded

Page 13 of 14

8. ASME Vlll - Rules for Construction of Pressure Vessels9. API 1104 - Welding of pipelines and related facilities10.APl RP520 - Sizing, Selection and installation of pressure relieving

devices in refineries: Part I - Sizing and selection;11.APl RP521 - Guide for pressure relieving and depressurising systems;

and12. API6D - Pipeline valves.

82. National Standards1. SANS 10089-1 South Africa National Standard, Storage and

distribution of petroleum products in above ground bulk storageinstallations;

2. SANS 10108 - Classification of hazardous locations and selection ofelectrical apparatus use in such location;

3. SANS 10142-1- The wiring premises;

4. SANS 1019 - Standard voltages, currents and insulation level forelectricity supply;

5. SANS 347 - Categorisation and conformity assessment criteria for allpressure equipment;

6. SANS 10227:2007 - Criteria for the operation of inspection authoritiesperforming inspection in terms of the Pressure Equipment Regulations;

7. SANS 1091 - National Colour standards for paint;

8. SANS 10228 - ldentification and classification of dangerous goods oftransport;

9. SANS 10231- Transport of dangerous goods: Operational requirementsfor road vehicles;

10. SANS 10232-2- Transport of dangerous goods: Emergency information

systems;11.SANS 10232-3 - Emergency response guides;

12.SANS29001: 2006 - Sector specific quality management system forpetroleum, petrochemical and natural gas industries - requirements forproduct and service supply organisations;

13. SANS347 - Pressure vessels and pressurised systems;14, SANS10227 lnspection in terms of the pressure equipment

regulations;15.SANS 347 - Categorisation and conformity assessment criteria for

pressure equipment and non-pressurised systems;16.SANS 10227 - Criteria for the operation of inspection authorities

performing inspection in terms of the pressure equipment regulations;

17. PER R374 dated 1 October 2009 - Pressure equipment regulation.

Page 14 ot 14