Getting Started

Visit www.HowToNoNo.com for Videos, Tips & Tricks

®

Contents Getting to Know no!no!®

4 Getting to Know no!no!®

6 Safety Warnings 8 Cautions 10 What to Expect 11 Where to Use

How to no!no!®

12 A Quick Introduction to no!no!®

14 Before Your First Treatment 14 Charging no!no!®

15 About Thermicon® Tips 17 Turning On/Off

18 Gliding no!no!® 21 About Blue and Red Light 24 Treating Facial Hair 26 After Every Treatment: Buff 27 Taking Care of Your no!no!®

Troubleshooting and Technical Specifications

28 Troubleshooting 29 Technical Specifications 30 Customer Support 33 Warranty

3

Getting to Know no!no!®

no!no!® is suitable for home use on all skin types and hair colors.

It is intended for both women and men, and is designed for the removal of body and facial hair through sustained periodic treatment.

Results take time, patience and a strong commitment to the treatment’s unique procedures. Each individual has an unique pattern of hair growth and each will experience results at their own pace.

READ this entire GETTING STARTED guide completely before using the device to ensure safety and results.

4

Getting to Know

no!no! ® The no!no!® Device

GuideLight Roller

Tip SocketPostsThermodynamic Wire

Thermicon® Wide Tip Thermicon® Narrow Tip

Thermodynamic Wire

On/OffButton

TreatmentLevel Icon

Battery Icon

Cover

Power SupplyConnection

5

Important Safety Instructions

• Always unplug this appliance immediately after charging the battery.

• Do not use while bathing.

• Do not place or store this appliance where it can fall or be pulled into a tub or sink.

• Do not use this appliance near water. Do not use this appliance near bathtubs, showers, basins or other vessels containing water.

• Do not reach for an appliance that has fallen into water, unplug it immediately.

When using electrical appliances, especially when children are present, basic safety precautions should always be followed, including the following:

READ ALL INSTRUCTIONS BEFORE USINGDANGER – To reduce the risk of electric shock:

6

• Use this appliance only for its intended use as described in this manual. Do not use attachments that are not recommended by the manufacturer.

• This appliance is only to be used with the power supply unit provided with the appliance for the purposes of recharging the battery.

• Keep the charging cord away from heated surfaces. Do not wrap the charging cord around the appliance or the power supply.

• Do not use an extension cord with this appliance.

• Never operate this appliance if it has a damaged cord or plug, if it is not working properly, or if it has been dropped, damaged, or dropped into water. Contact Customer Support to return the appliance to a service center for examination and repair.

Getting to K

now no!no! ®

KEEP THIS APPLIANCE AWAY FROM WATERWARNING - To reduce the risk of burns, electric shock, fire, or injury to persons:

7

• Do not open this device. No user serviceable parts inside.

• An appliance should never be left unattended when plugged in.

• Never use this appliance while sleepy or drowsy.

• Never block the openings of the appliance or place it on a soft surface, such as a bed or couch, where the openings may be blocked. Keep the openings free of lint, hair, and the like.

• Never drop or insert any object into any opening on this appliance. Do not insert metal objects into the charging socket.

• Do not use outdoors or operate where aerosol (spray) products are being used or where oxygen is being administered. This appliance is not suitable for use in the presence of flammable anesthetic mixture with air or with Oxygen or Nitrous Oxide.

8

• Do not place or store the appliance in very high temperature conditions (for example, in strong direct sunlight or inside a vehicle in extremely hot conditions).

• Do not charge or use this appliance if the temperature is below 0ºC / 32ºF or above 40°C / 104°F, when the appliance has been exposed to direct sunlight, a heat source, or where there is a lot of moisture.

• This device can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been supervised and instructed and understand the hazards involved.

• Keep the appliance, accessories and power supply out of reach of children under 8 years. Children should be supervised to ensure that they do not play with the appliance. Cleaning and user maintenance shall not be done by children.

Getting to K

now no!no! ®

9

• Do not use this appliance on sunburned skin, open cuts, bruises, blisters, moles or on raised areas such as scars.

• Do not use the appliance on irritated skin (e.g. eczema or inflamed skin reactions such as folliculitis (purulent hair follicles), skin with varicose veins, rashes, spots, moles (with hairs) or wounds without first consulting your physician.

• Persons with reduced immune response, during pregnancy or people who suffer from diabetes mellitus, haemophilia or immunodeficiency should also consult with their physician before use. If you have any skin condition other than those listed above, such cold sores, herpes, severe acne, please consult your physician before using this device. Always consult your physician before use if you have a pacemaker.

• Do not share use of the appliance. For hygiene reasons, the appliance should only be used by one person.

To reduce the risk of burns, electric shock, fire, or injury to persons:

CAUTION

10

• Do not use this appliance on the sensitive skin around the eyes, especially the area under the eyes. Do not use this device on eyebrows, eyelashes or scalp hair. Do not use this device on the genitals, on or around the areole (nipples), or near mucous membranes (nasal passages).

• Before using the appliance, make sure the skin surface is completely dry. Do not apply deodorants, lubricants, liquids, creams, gels, alcohol, water (etc.) to the area before use.

• Always check the Thermicon® Tip before use. Never use a Thermicon® Tip if the thermodynamic wire inside the Tip is bent, torn or dirty. Do not allow the thermodynamic wire to touch your skin.

• Always ensure that the main body of the appliance does not get wet (water splashing, condensation, etc.) and do not use with wet hands. Keep the appliance dry.

• Always unplug the appliance before cleaning.

• Do not use on animals, clothes, threads, brushes or other objects to prevent damage and injuries.

Getting to K

now no!no! ®

11

What to Expect - Get Ready To Engage Your Senses!When you use your no!no!®, the experience will surround you.TOUCH/FEEL - While everyone is different, some people experience a mild tingling when they first use no!no!®, especially over sensitive areas. This sensation fades and disappears after a few treatment sessions.

You may also feel a warming of the skin. If it is uncomfortably warm during treatment, take short breaks between use on any one area.

SMELL - Expect to smell the hair crystallizing as the patented Thermicon® technology treats the hair. The smell means it’s working!

SIGHT - While using your no!no!®, you will see the blue light when the tip and device are engaged. You will also see the hair crystallized and most will be removed when you get to the buffing stage. However, if there is any still remaining, follow up with another no!no!® treatment. Keep in mind that you are treating the hair even if it isn’t removed immediately.

SOUND - During your treatments, as you glide across the area you are treating, you will hear a low humming sound, like white noise.

12

Where to Use no!no!®

UnderarmsArms

Legs

Bikini Line

WOMEN can use on: WOMEN DO NOT use on:

Nipples Genitals Around the Eye Area or Eyebrows

MEN DO NOT use on:

Nipples Genitals Around the Eye Area or Eyebrows

Face

Chest

ArmsUnderarms

Legs

Back

MEN can use on:FaceNeck

13

Getting to K

now no!no! ®

ChooseTip

Wide Tip

Narrow Tip

A Quick Introduction to no!no!®

READ this entire GETTING STARTED guide before using the no!no!® to ensure safety and results.

1 2 3 4

Charge& Uncover

Turn OnInsert Tip

14

How

to no!no! ®

5 6

Glide Buff

Get Started

15

Before Your First Treatment

CHARGE the device for at least 5 hours. > Plug the charger into the device at the charger connection. > Plug the charger into a wall socket or outlet.> Place the device on a hard surface at the room temperature.> Charging is complete when the green Battery icon

on the Status Screen stops blinking. > Unplug the Charger from the wall and the device

once charging is complete.

Preparation > Cleanse the treatment area thoroughly, removing

all lotions, oils, gels or creams before use.

Test> Test a small area of the area you would like to treat. If there is any

discomfort, Stop and return to the area later.

Full Icon

16

Select Your Thermicon® Tip

Wide Tip

> Use the Wide Tip to treat large areas like the arms, legs, chest and back.

Narrow Tip

> Use the Narrow Tip for small sensitive areas like the face, neck, underarms and bikini line.

How

to no!no! ®

17

Insert the Thermicon® TipINSERTING the Thermicon® Tip

> Make sure the device is turned off.

> Hold no!no!® in one hand and the Tip in the other.

> Make sure both logos are facing the same direction and line up the posts in the socket with the holes in the Thermicon® Tip.

> Gently push into place.

REMOVING the Thermicon® Tip

> Grasp the Tip by both sides.

> Gently pull the Tip out of the socket.

When to REPLACE the Thermicon® Tip

> If the guiding light turns red.

> If it is no longer working efficiently.

> If the wire is damaged in any way.

> If the Thermicon® Tip Icon is blinking red on the Status Screen.

Notes:

> Make sure the Thermicon® Tip is placed properly into the socket before treatment.

> Never use a Thermicon® Tip if the wire is bent or torn.18

How

to no!no! ®

Turn no!no!® On [FIGURE A]

> Press the On/Off Button down until both the Battery and Tip Icon light up.

NOTE: If the red light appears, go to page 23 for further instructions.

A

19

B

Gliding no!no!®

Glide no!no!® at approximately a 90˚ angle with the Roller flat against your skin and the logo facing in the direction you are treating. [FIGURE B]

> Glide one way only, in the direction of the logo. Do not go back and forth.

Important Notes about Gliding:

20

90° angle

How

to no!no! ®> It is best to glide towards your body against the grain of the hair

growth. However, if it is more comfortable you may glide in other directions, but always in the direction of the Status Screen.

> Use a STEADY, SMOOTH and EVEN motion. If you move too slowly, the device will not activate; if you move too fast, you will not achieve optimal results.

> When gliding at the proper speed the blue light will be steady. A blinking or flickering blue light indicates that you may be moving too slowly. Once your movement has been adjusted, the blue light will remain steady.

> Do not press down too hard on your skin.

> You may need to go over an area more than once; 4-6 passes may be enough. If the skin is not uncomfortably warm, you may continue. If there is still hair left after buffing and your skin is too warm, wait a few minutes to return to the area. Try to remove all of the hair.

> Buff after each treatment to remove treated hair left behind.

21

Glide no!no!® on Rounded Areas> Make sure you practice on smooth even skin like your legs or arms

before moving to the face, knees, underarms or bikini line.

> Go slowly and allow no!no!® to follow the natural curve of the body.

NOTE: The face and bikini line may be extra-sensitive to temperature. If it becomes uncomfortably warm during treatment, STOP, work on a different area and return later.

DO NOT use no!no!® on the nipple or genital area, on or around the eye area or the eyebrows.

22

About the Blue and Red Light The Blue Light under the Thermicon® Tip will guide

you throughout your treatment. It is visible only when you are gliding no!no!® at the proper speed. [FIGURE C]

The Red Light appears only when the Thermicon® Tip is improperly installed, damaged or depleted or if the device needs to be charged. [FIGURE D]

How

to no!no! ®C

D

23

ON AND STEADY OFF Correct Gliding Speed

BLUE LIGHT RED LIGHT WHAT IT MEANS

OFF FLICKERING No Thermicon® Tip in Socket

OFF FLICKERING Depleted Thermicon® Tip

OFF FLICKERING Damaged Thermicon® Tip

FLICKERING OFF Incorrect Gliding Speed

OFF OFF Slow or No Movement

24

Treating Facial Hair [FIGURE G]

> TEST no!no!®

on a small, discreet area of the face on the lowest Treatment Level to see how your skin reacts.

> To treat the upper lip area, start under the nose and work your way outwards.

> When treating the chin, jawline or sideburns, start just below the base of the chin or jawline and glide no!no!

®

upwards following the curve of your face.

> Pull your skin tight and/or purse your lips inward to help create a smooth, straight surface.

> If there is any discomfort, STOP.

DO NOT allow your lips to come in contact with the thermodynamic wire.

DO NOT go over one area excessively.

NOTE: The area just below the eye and around the eyelid is especially sensitive.

DO NOT treat this area.

Go to www.HowToNoNo.com for helpful videos on how to maneuver no!no!® on the face.

How

to no!no! ®

After Every Treatment: Buff Buffing exfoliates, removes treated hair and leaves your skin feeling smooth. Without buffing, treated hair remains on the skin leaving a prickly feeling.

Hold the Buffer

> Firmly rub the Buffer in a circular and/or back and forth motion over the treated area. [FIGURE F]

When to Replace the Buffer

> When the pad feels smooth.

> When it is no longer buffing effectively.

F

26

Taking Care of Your no!no!®

NOTE: Do not use any liquid to clean the device, Thermicon® Tips or Rollers.

Keep the Thermicon® Tips and Roller clean to lower the risk of malfunction and prolong the life of the Tips.

1. Turn off your no!no!®.

2. Remove the Thermicon® Tip.

3. Gently brush the inside of the Tips clean. [FIGURE G]

4. Brush debris out and away from the socket and roller. [FIGURE H]

If any hair or debris falls into the socket, this may cause no!no!® to malfunction. Brush any particles out of the socket before beginning a treatment.

G H

How

to no!no! ®

27

TroubleshootingIf the no!no!® will not turn on: > Make sure it is charged. > Press and hold the On/Off Button for a few seconds

until the Status Screen lights up.If the no!no!® will not glide:> Make sure the Thermicon® Tip is not bent or torn and

is inserted correctly. Replace if necessary.> Increase gliding speed.If the Red Light comes on:> Check if the Thermicon® Tip needs to be replaced.> Restart your no!no!®.> Make sure the device is charged.If the device is not working properly contact no!no!® Customer Support for more troubleshooting tips or go to www.HowToNoNo.com.

The no!no!® warranty is only valid if no!no!® has been used according to the instructions in this guide (Pg. 33-34). Retain all receipts and original packaging.

28

Symbols on Device

On/Off Switch

CE mark represents the compliance to the European Low Voltage Directive 2006/95/EC and the Electromagnetic Compatibility Directive 2004/108/EC.

Protect the environment by not disposing of this product with household waste (2002/96/EC). Check your local authority or retailer for recycling advice and facilities (Europe only).

Refer to instruction manual. Indicates the need to consult accompanying documents.

Manufacturer

ICTV Brands Israel, Ltd. 5 Hanagar Street Hod Hasharon, 4501307 Israel

EU RepresentativeICTV Brands UK, Limited. 25 Horsell Road London, N5 1XL, U.K. Phone: +44 20 7319 9190 Fax: +44 20 7319 9191 info@ictvbrands.com

Customer SupportUS & Canada Customer Support: 888.525.7580

European Customer Support: +44 0344 482 5089

For additional no!no! products make sure to visit:

US & Canada: www.officialnono.com

United Kingdom: www.officialnono.co.uk

29

Troubleshooting and Technical Specifications

Technical SpecificationsWeight: 61.3gr

Physical Dimensions: 96.6 x 46.5 x 24.6mm [3.8 x 1.8 x 0.97in]

Mode of Operations: Continuous Battery: 680mAh LiPo

Operating Conditions Temperature: 5°C (41°F)-30°C(86°F)

Humidity: 30%-80% RH

Charger Rating: Input 100-240VAC/50-60Hz. 0.2A Output 8.4VDC 0.5A

Transport and Storage LESS THAN THREE MONTHS

Temperature: -10°C to 60°C

Humidity: 30-80%RH

Atmospheric Pressure: 0.1-1.5 atm.

Electrical Safety Power Supply: Class II equipment - double insulation. The Quality Management System of ICTV Brands Israel, Ltd. complies with the Quality Management Standard EN ISO 13485:2012.

Design and technical specifications are subject to change without notice.

© 2017 ICTV Brands®, Inc. no!no!® and Thermicon® are registered trademark of ICTV Brands®, Inc.

This device is protected by one or more U.S. and foreign patents and/or pending patent applications held by ICTV Brands, Inc.

no!no! complies with the following international standards Household and similar electrical appliances-Safety: IEC60355-1 and IEC60335-2-8

This equipment complies with FCC Rules, Part 15 and Industry Canada’s ICES-003 for a Class B Digital Device.

Operation is subject to two conditions:

(1) This device may not cause harmful interference, and

(2) This device must accept any interference that may cause any undesired operation.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.

30

If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

Industry Canada ICES-003 Compliance Label: CAN ICES-3 (B)/NMB-3(B)

Do not modify this product in any way. Any changes or modifications not expressly approved by the manufacturer could void the user’s authority to operate the equipment.

Technical Specifications

31

SAVE THESE INSTRUCTIONSBattery Storage & Removal

NOTE: For long term storage, your device should be stored at room temperature with the battery charged to about 40% to 60% of the battery capacity. The battery should be charged once every three months to retain optimal performance. If the device has been stored for more than three months, the battery should be fully discharged and then fully recharged again.

This appliance contains an embedded Lithium Polymer battery, which is not intended to be replaced. Do not attempt to replace the battery. This could result in the risk of fire or electric shock. Do not tamper with the device’s internal components. There are no user-serviceable parts inside. Do not put in fire or mutilate the battery during disposal as it may burst or release toxic materials.

When your appliance reaches the end of its useful life, the battery must be removed and recycled or disposed of properly in accordance with your local, provincial, state and/or government requirements.

The battery is to be disposed of safely. To remove the battery, do the following:

1. Disconnect the front panel by pushing from the bottom (place of the Thermicon® Tip) with a screwdriver.

2. Pull the circuit and the battery from the plastic frame.

3. Disconnect the battery wires from the circuit.

To prevent the battery pack from leaking, self-heating, or fire, please observe the following precautions:

• Be aware that a discharged battery may cause fire or smoke. Tape the terminals to insulate them.

• The soft aluminum packing foil is very easily damaged by sharp-edged parts such as Ni-tabs, pins and needles. Do not strike at battery pack with any sharp-edged parts.

• Do not immerse the battery pack in water or seawater.

• Do not leave the battery pack near a heat source as fire or heater.

• Do not leave the battery pack at very high ambient temperatures.

• Do not short-circuit the battery pack by directly connecting the positive and negative terminal with metal object such wire.

• Do not transport or store the battery together with metal objects such as necklaces, hairpins etc.

• Do not strike or throw the battery pack.

• Do not pierce the battery with a nail or other sharp object.

• If the battery pack leaks and the electrolyte get into the eyes, do not rub eyes, instead, rinse the eyes, with clean running water, and immediately seek medical attention.

• If the battery pack gives off an odor, generates heat, becomes discolored or deformed, or in any way appears abnormal during storage, immediately move it to a fireproof container.

32

WarrantyLimited Warranty:This Limited Warranty covers the no!no! product. The warranty provides for the repair or replacement of the device or its component parts, free of charge, within the warranty period.

Note: Certain items, such as Thermicon Tips and Buffers, are excluded from the coverage of this warranty, as they are spare parts/consumables and subject to wear and tear.

The warranty period is valid for one (1) year. In certain circumstances, an extended warranty may be available from the date of the original purchase of the device. When making a warranty claim, you must provide the following information: product serial number, date of purchase, guarantor’s name, address and phone number, together with the original sales receipt or invoice to verify the date of purchase. Any alteration or amendment of the purchase documents, including the sales receipt or invoice,

or failure to present the purchase documents at the time a warranty claim is made, will invalidate this warranty.

This warranty does not cover damage or deterioration:1. Incurred or reported more than one

(1) year or more when an extended warranty is purchased after the date of purchase;

2. Incurred due to improper use of the device;

3. Due to the modification or repair of the device by an unauthorized third party;

4. Due to damage or defects incurred during transportation or improper handling which were not reported at the time the product was received;

5. Due to humidity or any liquid or foreign body placed inside the device;

6. Due to the use of unapproved

accessories or attachments with the device;

7. Due to use contradictory to the procedures shown in the device’s user manual;

8. Due to Acts of God, natural events (floods, fire, lightning, etc.), force majeure or accidental or deliberate damage; or

9. Due to the device being subjected to high dust environments or excessive humidity or temperatures.

This Limited Warranty specifically disclaims and excludes all other warranties, whether express or implied in law, including the warranties of merchantability and fitness for a particular purpose. Manufacturer shall not be liable for any incidental or consequential damages that result from the use of this device. This warranty does not extend to any purchases made from

33

Battery Storage &

Warranty

anyone other than an authorized dealer in the no!no!® device.

This Limited Warranty gives specific rights to purchasers of the no!no!® Device; purchasers may have other rights that vary from country to country. In the United States, this Limited Warranty is governed by the laws of the State of Pennsylvania, regardless of any conflict of laws

provisions; any disputes under this warranty shall be adjudicated within the state courts situated in the county where the manufacturer is located.

For more information visit www.officialnono.com.

34

INSTNNMEN1/LIT-01000/REV. A01/Oct 2017

®