VIDEO CD Player - Sony

SONY MCE-F500 (E, C1, C2) 3-858-463-11

Actual page number:

3-858-463-11 (1)

VIDEO CDPlayerOperating Instructions

MMMMM

MMMMM

EN

C1

C2

C2

1996 by Sony Corporation

MCE-F500

SONY MCE-F500 (E, C1, C2) 3-858-463-11

Actual page number:

SONY MCE-F500 (E, C1, C2) 3-858-463-11

Actual page number:

2EN

WARNING

To prevent fire or shock hazard, do notexpose the unit to rain or moisture.To avoid electrical shock, do not open thecabinet. Refer servicing to qualified personnelonly.

Laser component in this product is capable of emittingradiation exceeding the limit for Class 1.

This appliance is classified as a CLASS 1 LASER product. TheCLASS 1 LASER PRODUCT MARKING is located on the rearexterior.

The following caution label is located inside of the unit.

Precautions

On safety• Caution – The use of optical instruments with this product

will increase eye hazard.• Should any solid object or liquid fall into the cabinet,

unplug the player and have it checked by qualifiedpersonnel before operating it any further.

On power sources• Before operating the player, check that the operating

voltage of the player is identical with your local powersupply. The operating voltage is indicated on the nameplateat the rear of the player.

• The player is not disconnected from the AC power source(mains) as long as it is connected to the wall outlet, even ifthe player itself has been turned off.

• If you are not going to use the player for a long time, besure to disconnect the player from the wall outlet. Todisconnect the AC power cord (mains lead), grasp the plugitself; never pull the cord.

• Should the AC power cord (mains lead) need to bechanged, have it done at a qualified service shop only.

On placement• Place the player in a location with adequate ventilation to

prevent heat build-up in the player.• Do not place the player on a soft surface such as a rug that

might block the ventilation holes on the bottom.• Do not place the player in a location near heat sources, or in

a place subject to direct sunlight, excessive dust ormechanical shock.

On operation• If the player is brought directly from a cold to a warm

location, or is placed in a very damp room, moisture maycondense on the lenses inside the player. Should this occur,the player may not operate properly. In this case, removethe disc and leave the player turned on for about an houruntil the moisture evaporates.

On adjusting volume• Do not turn up the volume while listening to a portion with

very low level inputs or no audio signals. If you do, thespeakers may be damaged when a peak level portion isplayed.

On cleaning• Clean the cabinet, panel and controls with a soft cloth

slightly moistened with a mild detergent solution. Do notuse any type of abrasive pad, scouring powder or solventsuch as alcohol or benzine.

If you have any questions or problems concerning yourplayer, please consult your nearest Sony dealer.

Welcome!Thank you for purchasing the Sony Video Compact Disc(VIDEO CD) Player. Before operating the unit, please readthis manual thoroughly and retain it for future reference.

About This ManualThe instructions in this manual are for model MCE-F500.

Conventions• Instructions in this manual describe the controls on the

player.You can also use the controls on the remote if they have thesame or similar names as those on the player.

• The following icons are used in this manual:

Indicates that you can use only the remote to dothe task.

Indicates tips and hints for making the task easier.

Zz

SONY MCE-F500 (E, C1, C2) 3-858-463-11

Actual page number:

3EN

TABLE OF CONTENTS

This Player Can Play the Following Discs ................................................................ 4

Getting StartedUnpacking ............................................................................................................................. 4Hooking Up the System ...................................................................................................... 5

Basic Operations

Playing a VIDEO CD .............................................................................................................. 8

Enjoying Playback Using the PBC FunctionsPlaying VIDEO CDs with PBC Functions (PBC Playback) ......................................... 10Locating Scenes Directly Using the Scene Numbers (Scene Search) ......................... 11

Locating a Scene or Track You WantUsing the On-Screen Display .......................................................................................... 13Using the Front Panel Display ........................................................................................ 14Resuming Playback from the Point You Stopped a VIDEO CD (Resume Play) ..... 15Locating a Specific Scene or Track ................................................................................. 16Locating a Particular Point in a Scene or Track ............................................................ 17Locating by Observing Several Scenes at One Time (Digest Play) ............................ 18

Playing CDs in Various ModesPlaying Repeatedly ........................................................................................................... 20Playing in Random Order (Shuffle Play) ...................................................................... 21Creating Your Own Program (Program Play) .............................................................. 21Reducing Distortion of the Picture (DNR) .................................................................... 23Adding an Incidental Image to Moving Pictures (COMET) ...................................... 23Playing Automatically When Turning On the Player (Auto Play) ............................ 24Switching the Sound ........................................................................................................ 24Controlling the TV with the Supplied Remote ............................................................. 25

Additional InformationNotes on Discs ................................................................................................................... 26Troubleshooting ................................................................................................................ 26Specifications ..................................................................................................................... 27Glossary .............................................................................................................................. 27

Index .......................................................................................................................................... 28

EN

SONY MCE-F500 (E, C1, C2) 3-858-463-11

Actual page number:

4EN

Getting Started

UnpackingCheck that you received the following items:• Audio and video connecting cord

(3 phono plugs – 3 phono plugs) (1)• Remote commander (remote) RMT-F500V (1)• Sony SUM-3 (NS) batteries (2)• Plug adaptor (1)

Inserting batteries into the remote

You can control the player using the supplied remote.Insert two R6 (size AA) batteries by matching the +and – on the batteries. When using the remote, point itat the remote sensor g on the player.

Getting StartedThis Player Can Play theFollowing Discs

Disc logo

Contents

Disc size

Play time

To play VIDEO CDs, see page 8.

To enjoy PBC Playback of VIDEO CDs with PBC functions,see page 10.

Note on VIDEO CDsThis player conforms to Ver. 1.1 and Ver. 2.0 of VIDEO CDstandards. You can enjoy two kinds of playback according tothe disc type.

Disc type

VIDEO CDs withoutPBC functions(Ver. 1.1 discs)

VIDEO CDs with PBCfunctions(Ver. 2.0 discs)

VIDEO CDs

Audio + Video(moving pictures)

12 cm/8 cm

74 min./20 min.

Audio CDs

Audio

12 cm/8 cm (CDsingle)

74 min./20 min.

You can

Enjoy video playback (movingpictures) as well as music.

Play interactive software usingmenu screens displayed on the TVscreen (PBC Playback), in additionto the video playback functions ofVer 1.1 discs. Moreover, you canplay high-resolution still pictures, ifthey are included on the disc.

z You can control Sony TVs with the g mark using thesupplied remoteSee page 25.

z When to replace batteriesWith normal use, the batteries should last for about sixmonths. When the remote no longer operates the player,replace all the batteries with new ones.

Notes• Do not leave the remote near an extremely hot or humid

place.• Do not drop any foreign object into the remote casing,

particularly when replacing the batteries.• Do not expose the remote sensor to direct sunlight or

lighting apparatuses. Doing so may cause a malfunction.• If you don’t use the remote for an extended period of time,

remove the batteries to avoid possible damage from batteryleakage and corrosion.

Playing CDsGetting Started

SONY MCE-F500 (E, C1, C2) 3-858-463-11

Actual page number:

5EN

Getting StartedGetting Started

R L

L

R

VIDEO

AUDIO

INPUTVIDEOOUT

AUDIO OUT

Hooking Up the SystemOverview

This section describes how to hook up the VIDEO CDplayer to a TV (with audio/video input jacks) and/oran amplifier. Be sure to turn off the power of eachcomponent before making the connections.

pWhen listening to the sound through TV speakers

VIDEO CD player

To AUDIOOUT

To VIDEOOUT

To an AC outlet

To video input

To audio input

TV

To an AC outlet: Signal flow

pWhen listening to the sound through speakersconnected to an amplifier

VIDEO CD player

To AUDIOOUT

To VIDEOOUT

To an ACoutletTV

To video input

To audioinput

: Signal flow

To an AC outlet

To an AC outlet

What cords will I need?Audio and video connecting cord (supplied) (1)

Yellow Yellow

Audio connecting cord (not supplied) (1)

White(L)Red(R)

Video connecting cord (not supplied) (1)

Yellow(video)

White(L)

Red(R)

Hookups

When connecting the cord, be sure to match the color-coded cord to the appropriate jacks on the components:Yellow (video) to Yellow, Red (right) to Red and White(left) to White. Be sure to make connections firmly toavoid hum and noise.

pWhen listening to the sound through TV speakers

Red(R)

White(L)

Yellow(video)

White(L)Red(R)

VIDEO CD player TV

pWhen listening to the sound through speakersconnected to an amplifier

VIDEO CD player

VIDEOOUT

R L

AUDIO OUT

L

R

VIDEO

AUDIO

INPUT

CD

L

R

Amplifier

TV

(Continued)

Amplifier

SONY MCE-F500 (E, C1, C2) 3-858-463-11

Actual page number:

6EN

Getting Started

AUTOPALNTSC

,

COLOR SYSTEM

S VIDEOOUT

S VIDEO IN

VIDEO CD player

S video cable

z If you have a digital component such as a DAT or MDYou can make digital recordings of audio CDs. Connectthe component via the DIGITAL OUT (OPTICAL)connector using the optical cable (not supplied). Take offthe cap and plug in the optical cable.

z If your TV or VCR has an S video input connectorConnect the component via the S VIDEO OUT connectorusing the S video cable (not supplied). You will get abetter picture.

YC-15V (not supplied)

ImportantSetting the color system switchThis player conforms to the NTSC and PAL colorsystems. Set the COLOR SYSTEM switch on the rearof the player to the appropriate position, accordingto your TV.

• If the color system of your TV is NTSC:Set the COLOR SYSTEM switch to NTSC. Pictureswill not be displayed if you set the switch to PAL.When you play a VIDEO CD recorded in the PALcolor system, the picture will be stretchedvertically and will be displayed with the upperand lower parts of the picture cut off.

• If the color system of your TV is PAL:Set the COLOR SYSTEM switch to PAL. Pictureswill not be displayed if you set the switch toNTSC. When you play a VIDEO CD recorded inthe NTSC color system, the picture will bestretched horizontally and will be displayed withthe upper and lower parts of the screen masked inblack.

• If your TV automatically changes the color systemaccording to the input signal:Pictures will be displayed with the switch set toeither NTSC or PAL.If you set the COLOR SYSTEM switch to AUTO,the player automatically changes the color systemof video output according to the color system ofthe VIDEO CD to be played. In this case, the colorsystem selected remains until you turn off theplayer, or you play another VIDEO CD with adifferent color system. If you turn off the player,the color system will be set to NTSC automaticallywhen you turn on the player again.

Be sure to turn off and on the player when youchange the setting.

TV

Optical cable

POC-15 (not supplied)

DIGITAL OUT DIGITAL IN

OPTICAL OPTICAL

Notes• You cannot make digital recordings of VIDEO CDs,

since this player does not output signals through theDIGITAL OUT (OPTICAL) connector while playing aVIDEO CD.

• When you connect via the DIGITAL OUT (OPTICAL)connector, noise may occur when you play CDsoftware other than music, such as a CD-ROM.

VIDEO CD player Digital component


SONY MCE-F500 (E, C1, C2) 3-858-463-11

Actual page number:

7EN

Getting StartedGetting Started

220 - 240V110 - 120V

VOLTAGE SELECTOR

Setting the VOLTAGE SELECTOR

Check that the VOLTAGE SELECTOR on the rearpanel of the player is set to the local power linevoltage. If not, set the selector to the correct positionusing a screwdriver before connecting the AC powercord to a wall outlet.When you set the selector to “110 – 120 V” position, besure to use the supplied plug adaptor.

Connecting the AC power cord

Connect the AC power cord to a wall outlet.

SONY MCE-F500 (E, C1, C2) 3-858-463-11

Actual page number:

Basic Operations

8EN

g

POWER

LEVELPHONES

AUTO PLAYOFF ON

DNR

RETURN SELECTNEXTPREV

OPEN/CLOSE

COMET

PLAY MODE

REPEAT

MENU/AMS

When using a TVTurn on the TV and select the video input so that you can viewthe pictures from this player.

When using an amplifierTurn on the amplifier and select the CD player position so thatyou can listen to the sound from this player.

Press POWER to turn on the player.

The indicator above the POWER button goes off and the frontpanel display lights up.

Press § OPEN/CLOSE, and place the disc on the disc tray.

Press ·.

The disc tray closes and the player plays all the tracks once(Continuous Play). Adjust the volume on the TV or theamplifier.

Playing a VIDEO CD

1• See pages 5 – 6 for the hookup

information.

• You can also play audio CDs justlike VIDEO CDs.

2z You can turn on the player

using the remotePress POWER while theindicator above the POWERbutton on the front panel islit.

Connect the headphones.

Adjust the headphonevolume.

2

4

3

z When playing VIDEO CDs withPBC functionsIn Step 4, the menu screenappears on the TV screen.You can play the VIDEO CDinteractively, following theinstructions on the menuscreen. (PBC Playback, seepage 10.)

z What is a VIDEO CD with PBCfunctions?See page 10 or 27.

3

4With the label side up

SONY MCE-F500 (E, C1, C2) 3-858-463-11

Actual page number:B

asic O

pera

tion

s

Basic Operations

9EN

To stop playbackPress p.

§ OPEN/CLOSE Jog Dial

SELECTpP·

z When “RESUME” appears inthe front panel displayYou can resume playbackfrom the point you stoppedthe VIDEO CD (ResumePlay, see page 15).

6 OPEN/CLOSE

·

P

p=/+

To

Pause

Resume play after pause

Go to the next scene or track/Go back to the precedingscene or track(in Continuous Play mode)

Stop play and remove the CD

z What is a track?A disc is divided intosections of a picture or amusic piece called “tracks.”Each track is assigned with atrack number to locate thetrack you want.

Press

P

P or ·

While playing, on the player:Turn Jog Dial to select the track number

While playing, on the remote:Go to the next scene or track +Go back to the preceding scene or track =

Before you start playing:Turn Jog Dial or press =/+ to select the tracknumber, then press SELECT or ·

§ OPEN/CLOSE

SONY MCE-F500 (E, C1, C2) 3-858-463-11

Actual page number:

10EN

Enjoying Playback Using the PBC Functions

1 2 3 4 5

6 7 8

PBCVIDEO CD

Playing VIDEO CDs with PBCFunctions (PBC Playback)When playing VIDEO CDs with PBC functions (Ver.2.0 discs), you can enjoy playing simple interactivesoftware, software with search functions, etc.PBC Playback allows you to play VIDEO CDsinteractively, following the menu screen on the TVscreen.On this player, you can use the number buttons, JogDial, SELECT, PREV, NEXT, and RETURN ˆ duringPBC Playback.Also refer to the instructions supplied with the disc, asthe operating procedure may differ according to theVIDEO CD.


2 Select the item number you want.

On the playerTurn Jog Dial to select the item number, then pressSELECT.

On the remotePress the number button of the item you want.When you want to select an item number over 20,press >20 first, then the corresponding numberbuttons. To enter “0,” use button 10.Exmaple: To select item number 30

Press >20 first, then 3 and 10.

3 Follow the instructions on the menu screen forinteractive operations.

When

Selecting the item

“SELECT” is flashingon the TV screen whileplaying movingpictures

Going back to themenu screen

Do the following

Turn Jog Dial on the player todisplay the item number, thenpress SELECT.

Press the number button of theitem you want on the remote.

In this case, you can go toanother scene even whileplaying moving pictures.Turn Jog Dial then pressSELECT on the player, or pressnumber button of the item youwant on the remote.

Press RETURN ˆ, PREV, orNEXT.(Also refer to the instructionssupplied with the disc, as theoperating procedure may differaccording to the VIDEO CD.)

Jog DialPREV/NEXT/RETURN ˆ

SELECT

Number buttons

· (SELECT)

>20

RETURN ˆ

PREV =

NEXT +

1 Start playing a VIDEO CD with PBC functions,following Steps 1 through 4 in “Playing a VIDEOCD” on page 8.The menu screen appears on the TV screen and“SELECT” flashes. The item numbers you canselect in the menu appear in the front paneldisplay.Note that some item numbers cannot be selectedeven if they appear in the front panel display.

Item numbers you can select

When ” CANNOT OPERATE NOW“ appears on theTV screenYou’ve pressed an invalid button. Press the correctbutton, following the instructions on the menu screen.

To cancel PBC Playback of a VIDEO CD with PBC functionsand play the disc in Continuous Play modeThere are two ways.• Before you start playing, select the track you want with Jog

Dial, then press SELECT. When using the remote, select thetrack with =/+, then press ·.

• Before you start playing, select the track number using thenumber buttons on the remote.

“PBC OFF” and “CONTINUE” appear in the front paneldisplay and the player starts Continuous Play. You cannotplay still pictures such as a menu screen.

z You can use · instead of SELECT after turning JogDial.


SONY MCE-F500 (E, C1, C2) 3-858-463-11

Actual page number:

11EN


SCENE – (1 – 312)

SPECIAL MENU

1) SCENE SEARCH 2) DISC DIGEST 3) TRACK DIGEST

.1 >2

Example of PBC Playback

This is an example of PBC Playback. Also refer to theinstructions supplied with the disc, as the operatingprocedure may differ according to the VIDEO CD.

TV screen

.1 >2

.1 >2

/3

?4

2MENU 1[1] AAAA[2] BBBB[3] CCCC[4] DDDD

MENU 2 (#1)[1] aaa[2] bbb

+ next page

MENU 2 (#2)[3] ccc[4] ddd

= previous page

Movingpicture, etc.

Moving picture,still picture, etc.

1 To select the item:Turn Jog Dial to select the item number, then pressSELECT, or select the number button you want on theremote.

2 To go to the preceding menu:Press ˆ.

3 To go to the next page of the menu:Press NEXT.

4 To go back to the preceding page of the menu:Press PREV.

Locating Scenes Directly Usingthe Scene Numbers(Scene Search) ZOn VIDEO CDs with PBC functions, the menu screens,moving pictures and still pictures are divided into“scenes” and each scene is assigned with a scenenumber.You can check the current scene number by displayingit on the TV screen during playback (see page 13). Besure to memorize the scene number from which youwant to start playing.

(Continued)

SPECIAL MENU

Number buttons(1–10)

CLEAR

·

1 Press SPECIAL MENU before you start playing orwhile playing a disc.The following menu appears on the TV screenwhile playing a disc.

TV screen

You cannot select the item with this mark.

2 Press button 1.“SCENE –” and the scene numbers appear on theTV screen.

TV screen

Total scene numbers

SONY MCE-F500 (E, C1, C2) 3-858-463-11

Actual page number:

12EN


SCENE 103 (1 – 312)

TV screen

Selected scene number

3 Press the number buttons (1 – 10) to select thescene.To enter “0”, use the button 10.Example: To select scene number 103

Press 1, then 10 and 3.The selected scene number appears on the TVscreen.

If you’ve made a mistakePress CLEAR, then press the correct number button.

4 Press · to start playing from the selected scene.The player automatically starts PBC Playback(page 10).

z You can check the scene number while playing a discPress ON SCREEN repeatedly to select ON SCREEN 2display mode (see page 13). The scene numbers appearon the upper left side of the TV screen.

Notes• Some discs don’t allow you to start playing from a

particular scene. In this case, when you do the task beforeyou start playing, the player starts playing from scene 1.When you do the task while playing a disc, the player startsplaying from the current scene.

• Some discs don’t display the selected scene on the TVscreen.

SONY MCE-F500 (E, C1, C2) 3-858-463-11

Actual page number:

Locating a Scene or Track You Want

13EN

Locating a Scene or Track You WantLocating a Scene or Track You Want

CD PLAYTRK 3 index 1 0:55CONTINUE

∗ ∗ 3 4 5 6 7 8 9 10 11 12 13 14 15

SCENE 1 0:55

VideoCD STOPTOTAL 10:04

PROGRAM

1. TRK 1 2. TRK 3 3. TRK 4

PLAY

When Using a VIDEO CD

pDisplay information of ON SCREEN 1 modeThe operating status is displayed for a few seconds onlywhen you change the operating status.

Playing status• “PLAY” when you start

playing• “STOP” when you stop

playing• “PAUSE” when you pause

playing

• Before you start playing (except for the Program Playmode)

• During PBC Playback (page 10)

Total playing time


Playing time of the scene(not displayedfor some scenes)

Scene number (page 11)

Programmed tracknumbers

Playing time on thecurrent track• “PLAY” is displayed

when you start playing• “PAUSE” is displayed

when you pause playingON SCREEN 1.

ON SCREEN 2.

ON SCREEN OFF

Current track number

Current index number

Playing time of the current track

Play mode

Music calendar

(Continued)

Using the On-Screen Display ZYou can check the operating status of the player andthe information about the disc with the on-screendisplay on the TV screen.

ON SCREEN

Press ON SCREEN.Each time you press the button, the on-screen displaychanges as follows:

When Using an Audio CD

The same information is displayed in ON SCREEN 1mode and ON SCREEN 2 mode while playing an audioCD.

pDisplay information of ON SCREEN 1 or ON SCREEN 2.

• In Continuous or Shuffle Play mode

pDisplay information of ON SCREEN OFF modeNo information is displayed.

pDisplay information of ON SCREEN 2 modeWhile playing a disc, the current track number and theplaying time are always displayed.The operating status is displayed for a few seconds onlywhen you change the operating status.The same information as in ON SCREEN 1 is displayedbefore you start playing.

• Before you start playing in Program Play mode

VideoCD PBC STOP47:55

CONTINUE MONO LREPEAT RESUMEDNR

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15

Music calendar*

Total playing timeSound indication

While playing VIDEO CDswith PBC functions

When Resume Play isavailable

Play mode

During Repeat Play

While DNR function isturned on(“COMET” is displayedwhen you selectCOMET.)

* The music calendar is not displayed during PBC Playback.

TRK 3 0:55

SONY MCE-F500 (E, C1, C2) 3-858-463-11

Actual page number:


14EN

CD STOPTOTAL 10:44

PROGRAM

1. TRK 1 2. TRK 3 3. TRK 4

CD PLAYTRK 3 index 1 0:55PROGRAM

1. TRK 1 2. TRK 3 3. TRK 4

• Before you start playing in Program Play mode

• In Program Play mode

• Before you start playing (except for the Program Playmode)

Using the Front Panel Display ZYou can check information about the disc using thefront panel display.Indicates the current track

Play mode

Total playing time

Music calendar

Total playing time of theprogram

Programmed track numbers

TIME

Checking the total number and playingtime of the tracks

Press TIME before you start playing.The front panel display shows the total number oftracks, total playing time and music calendar.

Total number of tracks

Total playing time

Music calendar

Music calendarPlayingtime

Indexnumber

Current tracknumber

"PBC" is displayedwhile playing aVIDEO CD with PBCfunctions.

"CONTINUE" is displayedwhile playing a VIDEO CDwithout PBC functions or anaudio CD.

pDisplay information of ON SCREEN OFF modeNo information is displayed.

Notes• Select the display mode other than ON SCREEN OFF for

normal operation. When you select ON SCREEN OFF, youcannot check the operating status while operating theplayer. In this case, check the information in the front paneldisplay.

• When you record the playback picture of this player onanother VCR, etc., be sure to select ON SCREEN OFF.Otherwise, the display information is also recorded on theVCR.

The information also appears when you press§ OPEN/CLOSE to close the disc tray.

Display information while playing a disc

pWhile playing a VIDEO CD without PBC functions or anaudio CDThe front panel display shows the current track number,playing time of the track, index number (page 17), and themusic calendar. The track numbers in the music calendardisappear after they are played.

CD STOP47:55

CONTINUE

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15

1 2 3 4 5

6 7 8 9 10

MIN SEC

VIDEO CDCONTINUE

1 2 3 4 5

6 7 8 9 10

MIN SEC

PBCVIDEO CD

INDEX

CONTINUE

SONY MCE-F500 (E, C1, C2) 3-858-463-11

Actual page number:


15EN


1 2 3 4 5

6 7 8 9 10

MIN SECINDEX

CONTINUE

1 2 3 4 5

6 7 8 9 10

MIN SECINDEX

CONTINUE

1 2 3 4 5

6 7 8 9 10

MIN SEC

CONTINUE

Resuming Playback from thePoint You Stopped a VIDEO CD(Resume Play)The player memorizes the point you stopped a VIDEOCD and you can resume playback from that point.Resume Play is not cancelled whenever you turn offthe player.Note that Resume Play is not available while playingan audio CD.

pWhile playing a VIDEO CD with PBC functionsThe track numbers and the music calendar aren’t displayed.However, while the menu screen is displayed on the TVscreen, the item numbers you can select in the menu appearin the music calendar.Note that you cannot select some item numbers even if theyappear in the music calendar.

Checking the remaining time

Each time you press TIME while playing a disc, thedisplay changes as shown in the chart below.Note that you cannot check the remaining time duringPBC Playback (page 10).

Playing time and number of the current track

Remaining time on the current track

Remaining time on the disc

This information does not appear in Program Playmode if the remaining time exceeds 100 minutes.

z What is a track?A disc is divided into sections of a picture or a musicpiece called “tracks.” Each track is assigned with a tracknumber to locate the track you want.

Press TIME

Press TIME

Press TIME

· p

1 While playing a VIDEO CD, press p to stopplayback.“RESUME” appears in the front panel display andon the TV screen.If “RESUME” doesn't appear, Resume Play is notavailable.

2 Press ·.The player starts playback from the point youstopped the VIDEO CD in Step 1.

z To view from the beginning of the VIDEO CDWhen "RESUME" appears in the front panel display,press p, then press ·.

Notes• Resume Play is not available in Digest, Shuffle or Program

Play mode.• Depending on where you stopped the VIDEO CD, the

player may resume playback from a different point.• The point at which you stopped playing is cleared when :

– you press number buttons, PLAY MODE or p– you turn the Jog Dial– you remove the VIDEO CD from the player– you unplug the AC power cord of the player

SONY MCE-F500 (E, C1, C2) 3-858-463-11

Actual page number:


16EN

Locating a Specific Scene orTrackYou can quickly locate any scene or track while playinga disc using the Jog Dial, =/+ buttons (AMS:Automatic Music Sensor) or number buttons.Note that while playing a VIDEO CD with PBCfunctions, this function is available only duringplayback without PBC functions (PBC OFF, page 10).

Jog Dial

z What is a track?A disc is divided into sections of a picture or a musicpiece called “tracks.” Each track is assigned with a tracknumber to locate the track you want.

NoteDuring PBC Playback, the Jog Dial, = and + buttonshave different functions from the ones explained above.

Number buttons

>20

=/+

pOn the playerTurn Jog Dial until you find the scene or track.

pOn the remote

To locate

The next orsucceeding scenes ortracks (AMS)

The current orpreceding scenes ortracks (AMS)

A specific trackdirectly Z

z When you directly locate a track numbered over 20 ZPress >20 first, then the corresponding number buttons.To enter “0,” use button 10.Example: To play track number 30

Press >20 first, then 3 and 10.

Press

+ repeatedly until you find thescene or track

= repeatedly until you find thescene or track

Number button of the track

SONY MCE-F500 (E, C1, C2) 3-858-463-11

Actual page number:


17EN


CD PLAYTRK 3 index 2 0:55CONTINUE

∗ ∗ 3 4 5 6 7 8 9 10 11 12 13 14 15

TRK 3 V-index 2

Locating a Particular Point in aScene or TrackYou can also locate a particular point in a scene ortrack while playing a disc.During PBC Playback (page 10), this function isavailable only while playing moving pictures.While playing an audio CD, Slow-motion Play is notavailable.

Locating a point using the index(Index Search) Z

There are two kinds of indexes: one is for audio CDsand the other is for VIDEO CDs. You can locate a pointyou want using the index.Note that this function is available only for indexeddiscs. Also note that you cannot search indexes indifferent tracks.

While playing a track, press INDEX C or crepeatedly.• To locate the current or preceding index numbers,

press INDEX C.• To locate the next or subsequent index numbers,

press INDEXc.

z What is an index?It is a number that divides a track or a disc into somesections in order to easily locate the point you want. Youmay determine if a disc uses index by looking at thedisc’s packaging.

NoteIf there are no more indexes while playing a VIDEO CD,“ CANNOT OPERATE NOW” appears on the TV screenand the player continues playing.

TV screen (while playing an audio CD)ON SCREEN 1 or 2 display mode

TV screen (while playing a VIDEO CD)ON SCREEN 1 or 2 display mode

Index number

Front panel display

Index number

Index number

3 4 5

6 7 8 9 10

MIN SEC

VIDEO CD

INDEX

CONTINUE

0 )

& SLOWINDEX C/c0/)

To locate a point

While monitoring thepicture or sound Z

Slowly by observingthe TV screen(Slow-motion Play) Z

Quickly by observingthe front panel displayduring pause

z If you want to locate a particular point of a long trackIt is convenient to use Track Digest (see page 19).

z If “ ” appears in the front panel displayThe disc has reached the end while you were pressing). Press 0 or = to go back.

z If you want to change the playback speed duringSlow-motion Play ZPress & SLOW repeatedly until you find the playbackspeed you want. Three speeds are available: SLOW 1 (1/5th the normal speed), SLOW 2 (1/10th) and SLOW 3 (1/15th). Each time you press the button, the indicationchanges as follows.

NoteWhile playing a VIDEO CD, the picture may be distortedduring the search operation.

Press

) (forward) or 0 (backward)and hold down until you find thepoint. You will not hear the soundwhile playing a VIDEO CD.

& SLOW. You will not hear thesound during the operation. Whenyou find the point, press ( toreturn to the normal speed.

0/) and hold down until youfind the point. You will not hear thesound during the operation.

n SLOW 1 n SLOW 2 n SLOW 3

SONY MCE-F500 (E, C1, C2) 3-858-463-11

Actual page number:


18EN

SPECIAL MENU


Locating by Observing SeveralScenes at One Time(Digest Play) ZYou can locate the track or scene you want byobserving several still pictures at one time on the TVscreen.Note that while playing a VIDEO CD with PBCfunctions, this function is available before you startplaying or during playback without PBC functions(PBC OFF, page 10).While playing a VIDEO CD, you will not hear thesound.While playing an audio CD, you will only hear thesound.

2 Press button 2.The TV screen shows still pictures of the firstscenes of tracks 1 to 9 on the disc.

TV screen

To view still pictures of the tracks numbered over 9Press +. The TV screen shows still pictures of tracks 10to 18.If there are more tracks, “+” is displayed on the upperright side of the TV screen.To go back to the previous screen, press =.

3 Press the number button to select the track.The player starts playing from the selected track.

To select tracks numbered over 20Use the >20 button (see page 16).

To cancel Disc DigestPress p.

z While the still pictures are displayed in Step 2, youcan start playing the track you want right awaybefore all the still pictures are displayedPress · when the picture of the track you want appearson the TV screen.

Notes• If you start Disc Digest before you start playing a VIDEO

CD with PBC functions, the player automatically startsplaying without PBC functions (PBC OFF, page 10).

• When you start Disc Digest in Shuffle or Program Playmode, the player automatically enters Continuous Playmode (page 8).

SPECIAL MENU

>20

Number buttons

Locating the track you want on a disc(Disc Digest)

You can locate the track you want by observing thefirst picture of up to 9 tracks on the disc at one time onthe TV screen.

1 Press SPECIAL MENU while playing a disc orbefore you start playing.The following menu appears on the TV screen.

TV screen

DISC DIGEST

1 2 3

4 5

7 8 9

6

SONY MCE-F500 (E, C1, C2) 3-858-463-11

Actual page number:


19EN


TRACK 1 DIGEST

1 2 3

4 5

7 8 9

6

SPECIAL MENU


Locating the point you want in a track(Track Digest)

You can have the player divide a track into 9 sections.You can locate the point you want by viewing the firstpicture of each section at one time on the TV screen.This might be useful when you play a disc which isdivided into few tracks, such as a movie.

1 Press SPECIAL MENU while playing a disc orbefore you start playing.The following menu appears on the TV screen.

2 Press button 3.The player divides the track into 9 sections and theTV screen shows still pictures of each section inorder.

TV screen

3 Press the number button (1 – 9) to select the pointyou want.The player starts playing from the selected point.The player may start playing from a point which isa little different from the one displayed duringTrack Digest.

To cancel Track DigestPress p.

TV screen

Currenttrack

z You can select a point which isn’t displayed yet onthe TV screen in Step 2

z During Track Digest, you can start Track Digest onanother trackPress = or +.Note that this function is not available in Shuffle orProgram Play mode.

Notes• If you start Track Digest before you start playing a VIDEO

CD with PBC functions, the player automatically startsplaying without PBC functions (PBC OFF, page 10).

• If you start Track Digest before you start playing in Shuffleor Program Play mode, the player automatically entersContinuous Play mode (page 8).

• When a track is shorter than about 40 seconds, the playermay divide the track into less than 9 sections.

SONY MCE-F500 (E, C1, C2) 3-858-463-11

Actual page number:

20EN

Playing CDs in Various ModesPlaying CDs in Various Modes

Playing RepeatedlyYou can play all the tracks, a single track or a specificportion repeatedly.

REPEAT ·

Repeating all the tracks on a disc

In Shuffle or Program Play mode, the player repeatsthe track in the shuffled or programmed order.You cannot do Repeat Play during PBC playback(page 10) or Digest Play (page 17).

Press REPEAT while playing a disc.“REPEAT” appears in the front panel display. Theplayer repeats the tracks as follows:

When the disc is played in

Continuous Play(page 8)

Shuffle Play(page 21)

Program Play (page 21)

To cancel Repeat PlayPress REPEAT repeatedly until “REPEAT” disappears fromthe front panel display.

The player repeats

All the tracks

All the tracks in random order

The same program

A˜BREPEAT

·

Repeating the current track

You can repeat only the current track in ContinuousPlay mode (page 8).

While the track you want is being played, pressREPEAT repeatedly until “REPEAT 1” appears in thefront panel display.

To cancel repeating the current trackPress REPEAT repeatedly until “REPEAT 1” disappears fromthe front panel display.

Repeating a specific portion(A˜B Repeat) Z

You can play a specific portion in a track repeatedly.This might be useful when you want to memorizelyrics.During PBC Playback (page 10), this function isavailable only while playing moving pictures.

1 While playing a disc, press A˜B when you findthe starting point (point A) to be playedrepeatedly.“A–” of “REPEAT A–” flashes in the front paneldisplay.

2 When you reach the ending point (point B), pressA˜B again.“REPEAT A–B” appears. The player plays thisspecific portion repeatedly.

To cancel A˜B RepeatPress REPEAT.

z When you want to restart from the starting point APress · during A˜B Repeat.

SONY MCE-F500 (E, C1, C2) 3-858-463-11

Actual page number:

Playing CDs in Various Modes

21EN


2 5

8

MIN SECSTEP

PROGRAM

1 2 3 4 5

6 7 8 9 10

PROGRAM

Playing in Random Order(Shuffle Play)You can have the player “shuffle” tracks and play in arandom order.

Creating Your Own Program(Program Play)You can arrange the order of the tracks on the discsand create your own program. The program cancontain up to 24 tracks.

PLAY MODE

Jog Dial

· pP SELECT

Number buttons

CHECK

CLEAR

pP=/+

·

>20

PLAY MODE

”PROGRAM“ is lit

1 Press PLAY MODE repeatedly until “PROGRAM”appears in the front panel display.

Total playing time

Programmed order

Last programmedtrack

Programmed tracks

(Continued)

PLAY MODE ·

PLAY MODE

·

1 Press PLAY MODE repeatedly until “SHUFFLE”appears in the front panel display.

1 2 3 4 5

6 7 8 9 10

SHUFFLE

”SHUFFLE“ is lit

2 Press the number buttons of the tracks you want toprogram in the order you want. ZBe sure to use the remote.Example: To program the tracks in the order 2, 8, 5

Press the number buttons 2 n 8 n 5.To program a track numbered over 20, use the >20button (see page 16).

2 Press · to start Shuffle Play.The indication appears while the player is“shuffling” the tracks.

To cancel Shuffle PlayPress PLAY MODE repeatedly until “CONTINUE” appears inthe front panel display.

z You can start Shuffle Play while playing in ContinuousPlay modePress PLAY MODE repeatedly until “SHUFFLE” appearsin the front panel display. Shuffle Play starts from thecurrent track.

NoteIf you play a VIDEO CD with PBC functions in Shuffle Playmode, you cannot use the PBC functions.

SONY MCE-F500 (E, C1, C2) 3-858-463-11

Actual page number:

22EN


If you’ve made a mistakePress CLEAR, then press the correct number button.

3 Press · to start Program Play.

To cancel Program PlayPress PLAY MODE repeatedly until “CONTINUE” appears inthe front panel display.

z You can check the total playing time whileprogramming in Step 2 (Program Edit)1 Turn Jog Dial or press = or + until the track you

want to program appears in the front panel display.The total playing time including the selected trackappears in the front panel display.

2 Press SELECT or PLAY MODE to confirm yourselection.

3 Repeat Steps 1 and 2 to program more tracks.

z You can insert a pause as one stepDuring programming, press P to insert a pause. Thetotal playing time is reset to “0.00.”When playing a program which contains a pause, theplayer pauses at the step in which a pause isprogrammed, until you press P or ·. This might beuseful when you record a program on both sides of atape.

z You can check the contents of the program duringprogramming on the TV screenIf you press ON SCREEN to select ON SCREEN OFFdisplay mode, you won’t see this information (page 13).

z The program remains even after the Program PlayendsWhen you press ·, you can play the same programagain.

Notes• If you play a VIDEO CD with PBC functions in Program

Play mode, you cannot use PBC functions (page 10).• If the total playing time exceeds 100 minutes, “– – . – –”

appears in the front panel display.• If you program more than 24 tracks, “FULL” appears in the

front panel display and on the TV screen.

Checking the track order Z

You can check your program before or after you startplaying.

Press CHECK.Each time you press this button, the front panel displayshows the track number and the total playing time inthe programmed order. After the last track in theprogram, the front panel display shows “End” andreturns to the original display.

Changing the track order

You can change your program before you start playing.

To

Erase a track Z

Erase the last track inthe program Z

Add tracks to the endof the program Z

Change the wholeprogram completely

Press

CHECK until the track you don’twant appears in the display, thenpress CLEAR.

CLEAR. Each time you press thisbutton, the last track is cleared.

Number buttons of the tracks to beadded.

p (stop). Create a new programfollowing the programmingprocedure.

SONY MCE-F500 (E, C1, C2) 3-858-463-11

Actual page number:


23EN


Reducing Distortion of thePicture (DNR: Digital NoiseReduction)You can make picture clearly by reducing distortion ofthe picture.

Adding an Incidental Image toMoving Pictures (COMET)You can enjoy the picture which leaves an incidentalimage, such as a trail of comet. The COMET functiongives an atmosphere to the picture.

Press COMET. The COMET button indicator lights up.

To cancel the COMET functionPress COMET again. The COMET button indicator goes off.

NoteIf you press DNR, the COMET function is cancelled.

COMETDNR

COMETDNR

To cancel the DNR functionPress DNR to goes off the DNR button indicator.

To turn on the DNR function againPress DNR to lights up the DNR button indicator.

Notes• If you press COMET, the DNR function is cancelled.• The DNR function cannot reduce the outline noise of the

picture or block noise on the picture.• The effect of the DNR function may not be noticeable with

the disc which contains low level noise.• When you connect the AC power cord of the player to a

wall outlet, the DNR function is automatically turned on.

SONY MCE-F500 (E, C1, C2) 3-858-463-11

Actual page number:

24EN


Switching the Sound ZOn multiplex discs, you can select the sound from theright or left channel and listen to the sound of theselected channel through both the right and leftspeakers. In this case, the sound loses the stereo effect.

L/R/STEREO

You will hear

The sound of the left channel

The sound of the right channel

The standard stereo sound

Indication*

MONO L

MONO R

STEREO**

Press L/R/STEREO while playing a disc.Each time you press the button, the indication and thesound from the speakers change as follows:

Press

Once

Twice

Three times

* When you select ON SCREEN OFF display mode, check theindication on the front panel display.

** This indication doesn’t appear in the front panel display.

NoteWhen you turn off the player, the standard stereo playbackwill be resumed.

Playing Automatically WhenTurning On the Player (AutoPlay)You can start playing automatically when you turn onthe player.By connecting a timer (not supplied), you can startplaying at any time you want.

AUTO PLAY

Set AUTO PLAY to ON.The player starts playing automatically when you turnon the player.

To cancel Auto PlaySet AUTO PLAY to OFF.

NoteIf you start playing with Auto Play function, the playerautomatically starts Continuous Play (When a VIDEO CDwith PBC functions is in the player, PBC playback starts). Theplayer cannot start in Shuffle Play or Program Play mode.

SONY MCE-F500 (E, C1, C2) 3-858-463-11

Actual page number:


25EN


Controlling the TV with theSupplied Remote ZYou can control Sony TVs with the g mark using thesupplied remote.

Press

POWER

TV/VIDEO

VOL

CH

You can

Turn on or off the TV

Select the input source to the TV

Adjust the volume of the TV

Change the channel of the TV

TV/VIDEO

POWERCH

VOL

SONY MCE-F500 (E, C1, C2) 3-858-463-11

Actual page number:

26EN

Additional Information

TroubleshootingIf you experience any of the following difficulties whileusing the player, use this troubleshooting guide to helpyou remedy the problem. Should any problem persist,consult your nearest Sony dealer.

There’s no sound./Check that the player is connected securely./Make sure you operate the TV or the amplifier

correctly./Make sure you select the CD player position on

the amplifier.

There’s no picture./Check that the player is connected securely./Make sure you operate the TV correctly./Make sure you set the COLOR SYSTEM switch

correctly, according to your TV.

The picture is distorted./Clean the disc (see page 26).

The disc doesn’t play./There’s no disc inside (“no dISC” appears).

Insert a disc./Insert the disc with the label side up on the disc

tray correctly./Clean the disc (see page 26)./Moisture has condensed inside the player.

Remove the disc and leave the player turned onfor about an hour (see page 2).

The sound loses stereo effect./“MONO R” or “MONO L” appears in the front

panel display (see page 24).

The remote doesn’t function./Remove the obstacles in the path of the remote

and the player./Point the remote at the remote sensor g on the

player./Replace all the batteries in the remote with new

ones if they are weak.

The player doesn't play from the first track when playinga VIDEO CD without PBC functions or an audio CD./Press PLAY MODE repeatedly until

“CONTINUE” appears in the front paneldisplay, then press ·.

Notes on Discs

On handling discs• To keep the disc clean, handle the disc by its edge. Do not

touch the surface.• Do not stick paper or tape on the disc.

If there is glue (or a similar substance) on the disc, removethe glue completely before using the disc.

• Do not expose the disc to direct sunlight or heat sourcessuch as hot air ducts, or leave it in a car parked in directsunlight as there can be considerable rise in temperatureinside the car.

• After playing, store the disc in its case.

On cleaning• Before playing, clean the disc with a cleaning cloth. Wipe

the disc from the center out.

• Do not use solvents such as benzine, thinner, commerciallyavailable cleaners or anti-static spray intended for vinylLPs.

Not this way


SONY MCE-F500 (E, C1, C2) 3-858-463-11

Actual page number:

27EN


Glossary

Auto Pause

Automatic pause function that works according to thesignal encoded on the disc during PBC playback. Inthis case, “AUTO P” appears in the front paneldisplay. If the player doesn’t resume play for a longtime, press P or · to resume play manually.

PBC Playback

Playback using the menu screens recorded on VIDEOCDs with PBC functions. You can enjoy simpleinteractive operations using the PBC Playbackfunction.

Playback Control (PBC)

Signals encoded on VIDEO CDs (Version 2.0) tocontrol playback.By using menu screens recorded on VIDEO CDs withPBC functions, you can enjoy playing simpleinteractive software, software with search functions,and so on.When you insert a VIDEO CD with PBC functions onthis player, “PBC” appears in the front panel display.

Track

Sections of a picture or a music piece on a disc. Eachtrack is assigned with a track number to locate thetrack you want.

VIDEO CD

A compact disc that contains moving pictures.The picture information uses the MPEG 1 format, oneof the world wide standards of digital compacttechnology. The picture information is compressedabout 120 times. Consequently, a 12 cm VIDEO CD cancontain up to 74 minutes of moving pictures.VIDEO CDs also contain compact audio information.Sounds outside the range of human hearing arecompressed while the sounds we can hear aren’tcompressed. VIDEO CDs can hold 6 times the audioinformation of conventional audio CDs.There are 2 versions of VIDEO CDs.• Version 1.1: You can play only moving pictures and

sounds.• Version 2.0: You can play high-resolution still

pictures and enjoy PBC functions.This player conforms to both versions.

Specifications

VIDEO CD player

Laser Semiconductor laser

Wavelength 780 – 790 nm

Signal format system NTSC, PAL

Frequency response 2 Hz to 20 kHz ±0.5 dB

Signal-to-noise ratio More than 94 dB

Outputs

AUDIO OUT

DIGITAL OUT(OPTICAL)

VIDEO OUT

S VIDEO OUT

PHONES

General

Power requirements 110 – 120 V or 220 – 240 V AC,adjustable, 50/60 Hz

Power consumption 22 W

Dimensions (approx.) 430 × 95 × 278 mm(w/h/d) incl. projecting parts

Mass (approx.) 3.7 kg

Supplied accessoriesAudio and video connecting cord (3 phono plugs – 3phono plugs) (1)Remote commander (remote) RMT-F500V (1)Sony SUM-3 (NS) batteries (2)Plug adaptor (1)

Design and specifications are subject to change without notice.

Jacktype

Phonojacks

Opticaloutputconnector

Phonojack

4-pin miniDIN

Phonejack

Maximumoutputlevel

2 V(at 50 kilohms)

–18dBm

1 Vp-p

Y: 1 Vp-p

C: 0.286 Vp-p

10mW

Load impedance

Over 10 kilohms

Wave length: 660nm

75 ohms, unbalanced,sync negative, whitepeak

75 ohms, unbalanced,sync negative

32 ohms

SONY MCE-F70 (E, C1, C2) 3-858-463-11

28EN


Index

A, BA-B repeat 20Adjusting

volume 8AMS 16Auto Pause 27Automatic Music Sensor. See

AMS

CColor system switch 6Comet 23Connecting 5Continuous play 8

D, EDigest Play 18Disc Digest 18Display

front panel display 14on-screen display 13

DNR 23

F, GFront panel display 14

HHandling CDs 25Hooking up 5

I, J, KIndex 17Index Search 17

Names of controls

ButtonsA˜B 20CHECK 22CLEAR 22COMET 23DNR 23INDEX C/c 17L/R/STEREO 24Number 10, 16ON SCREEN 13§ OPEN/CLOSE 8PLAY MODE 21PREV/NEXT 10REPEAT 20RETURN ˆ 10SELECT 8, 10SPECIAL MENU 11, 18& SLOW 17TIME 14· 8, 10P 9p 9=/+ 9, 100/) 17>20 16

SwitchAUTO PLAY 24POWER 8

ControlJog Dial 9, 10PHONES LEVEL 8

JackPHONES 8

OthersDisc tray 8Front panel display 14g 4

L, M, NLocating

a specific point 17a specific scene 16a specific track 16by monitoring 17by observing the front panel

display 17directly 16using AMS 16using index 17

OOn-screen display 13

P, QPBC functions 10, 27PBC Playback 10, 27Playback

Continuous Play 8Program Play 21Repeat Play 20Shuffle Play 21

Programchanging 22checking 22

RRemaining time 15Remote control 4Repeating 20Resume Play 15

SScene 11Scene Seach 11Searching. See LocatingShuffle Play 21Slow-motion Play 17Switching the sound 24

TTotal playing time 14Track Digest 19Troubleshooting 26

UUnpacking 4

V, W, X, Y, ZVIDEO CDs 4, 8, 27Voltage selector 7

Index

SONY MCE-F70 (E, C1, C2) 3-858-463-11

Actual page number:

29EN


SONY MCE-F500 (E, C1, C2) 3-858-463-11

Actual page number:

Sony Corporation Printed in Japan

VIDEO CD Player - Sony

Documents

Transcript of VIDEO CD Player - Sony