VectaStar System Overview Next generation thinking
Transcript of VectaStar System Overview Next generation thinking
VectaStar Gigabit today
VectaStar Gigabit ODU-S
− 10.5, 26, 27* & 28GHz: 7/14/28MHz, 300Mbps Ethernet throughput per AP (28 MHz@256QAM)
− Fully GA, full ETSI Approval (*subject to Type Approval)
Features
− Zero-footprint sector mode supporting up to 8 RTs with no indoor base station equipment
− With Radio Controller:
− 30 RTs supported per sector
− Full indoor Redundancy (parallel Radio Controllers)
− Full Outdoor Redundancy (1+1 & 2+0 AP options per sector)
− Support for TDM on VSG platform using MPA at RC-based hub with IDU-4VL-4E1 at Remote Terminals
− Supports AP-VS2, AP-GE and AP-S sectors
− 7-state hitless adaptive modulation (QPSK up to 256QAM)
Benefits
− Excellent return on investment due to low $/MByte
− High spectrum efficiency with 7 modulation states
− Up to full sector throughput to a single RT
− Lower installation & maintenance costs with slip-fit antennas and improved cable management
− Enables system migration from VS2 to VectaStar Gigabit
− Support for IP optimisation
Commercial in confidence 2
Enhanced Features of ODU-S
− 10.5GHz - Single variant AP and RT – increased power output +23dBm
− Additional 28MHz channel support at 10.5GHz
− 7/14/28MHz for all variants - 10.5/26/27/28GHz
− 300Mbps net Ethernet sector capacity using 28 MHz channel @ 256QAM
− 600Mbps net Ethernet sector capacity with 2+0 operation (26,27,28GHz only)
− Smaller, lighter form factor (~4kg) with simplified antenna interface
− Polarisation set simply by rotation of ODU
− Tilt sensor provides polarisation configuration feedback via VNMS
Additional Benefits of ODU-S
− Compatibility with VectaStar
Gigabit and VS2
− Less wind loading
− Easy to install
− ODU-S hardware TDM ready
− SyncE capable
− Support for IP optimisation*
VectaStar Gigabit ODU-S
3
ty ** Candidate roadmap feature
Commercial in confidence
Extension Kit for VSG CAT5 ODUs
• Enables a distance extension of >100m for CAT-5e ODUs
• Converts from fibre to CAT-5e, using an ORing media converter and other components
• Environmental: Rated to +55oC, Indoor Use Only
• Order Code: EXT-KIT-VSG-CAT5-ODU
• Description: Extension Kit for VSG CAT5 ODUs (inc. Media converter and SM SFP,
converts Cat5 ODU to fibre media)
Commercial in confidence 4
Customer Responsibilities:
• Kit must be assembled onto the supplied DIN
rail by the customer
• Kit requires a fibre connection on the
customer’s equipment
• Customer to provide IDU-GPI, LP-GE, Fibre
cable and connectors, 48VDC supply and
cables (these items not contained in the kit)
Status: released and available
VectaStar Gigabit Radio Controller
• Features
− Supports 8 APs per RC or 6 per redundant RC
− Enables up to 30 RTs per sector
− Supports up to 240 Remote Terminals
− AP-only and Full (RC and AP) redundancy
− 1U footprint, all interfaces front-panel
− Ten Gigabit Ethernet interfaces
− Two 10 Gigabit Ethernet core interconnections*
− Support for TDM services* (with Fibre AP)
− Support for fibre and copper** SFP
5
• Benefits− Elegant, small solution for dense
urban networks
− Resilient interconnection to core
− Simple and flexible installation
options
− Supports low-latency X2 and flat
networks
*Check timeline for availability, **Check release notes
Commercial in confidence
2+0 Access Point (AP) redundancy
• Features• Separate channels used for redundant sector APs (26,27,28GHz)
• Enables 600Mbps total sector capacity (2 x 300Mbps APs using 28MHz channels @256QAM)
• If AP1 fails, all RTs registered with AP1 move to AP2 until AP1 restored
• Benefits• Doubles sector capacity compared to 1+1 redundancy
• No extra hardware required over 1+1
• Software feature for 1+1 redundant AP configurations
6Commercial in confidence
2+0 sector in
normal operation
AP1
AP2
AP1
AP2
Sector operation
if an AP failsF1
F2 F2600Mbps
sector capacity
300Mbps
sector capacity
If AP1 fails, all RTs registered with AP1 move to AP2 until AP1 restored
VectaStar Gigabit capacity roadmap
Four principal LTE requirements
1. Capacity
● Current VectaStar Gigabit
− Provides a 300Mbps Ethernet sector capacity on a single channel.
− Each link is capable of full sector capacity
− Current 2+0 AP doubles sector capacity to 600Mbps using 2 channels per sector
• Wide-Band 56MHz channel radio doubles sector capacity to 600Mbps per channel, 1.2Gbps for 2+0 sector
● IP optimisation* in Terminal Station and
● Radio Controller increases sector
● capacity to ~ 1.4Gbps (link ~ 700Mbps)
LTE 20MHz carrier, 2+2 MIMO base station maximum throughput is 170Mbps
7
0
200
400
600
800
1000
1200
1400
VSG 28MHzchannel
2+0 Protection Wideband56MHz
IPOptimisation**
Link Sector
Commercial in confidence
* Candidate feature
VectaStar Gigabit – Other LTE requirements
Four principal LTE requirements (cont’d)
2. Synchronisation
− VectaStar supports flexible synchronisation schemes, currently E1, 1588v1, 1588v2, external clocking and NTPv4
− SyncE support on VectaStar Gigabit - hardware support now, see Roadmap for software release
− Flexible platform means evolving standards can be tracked
3. X2 switching and flat network support
− VectaStar Gigabit supports high-capacity switching from core to end-points, and from end-point to end-point, simplest flat network hierarchy supported
4. Low end-to-end latency
− LTE requirement is maximum 10ms end-to-end
− VectaStar IP round trip latency today is average < 0.6ms with 99.9% < 1ms
VectaStar Gigabit is LTE-ready Now
8Commercial in confidence
VectaStar Gigabit Ethernet and TDM Services
9
Fibre AP-GE or
AP-S **
Legend
Gigabit Ethernet
Fast Ethernet
E1
STM-1
Gigabit Ethernet with -48V DC
IDU-4VL-4E1VSG-DON-4VL
SW
5.1 FP1
VSG-RC **
VC-4 or VC-12* Check for release dates
** Hardware is SyncE capable
MPA
RTs
VSG or ODU-S **
IDU-GPI
** GigE only
Fast Ethernet & 4xE1
SW:
0 & 4E1 5.4 *
8xE1*
GigE & 4 or 8xE1 with VSG IDU
VSG-IDU-6VL-4E1 or 8E1 * **
** GigE & up to 40 concatenated E1s with VSG IDUs
Candidate
Feature
Commercial in confidence
GE – IDU*
Features
•Dual power supply inputs.
•1 dedicated port carries power and data to the
ODU
•All connections on the front panel
•Wall or rack mount
•Reduced footprint (30% smaller than current IDU)
•4 SyncE capable RJ-45 interfaces
•2 SFP GE interfaces (SyncE capable with fibre
SFP), release with 8xE1 variant
•3 variants with 0, 4 or 8xE1 interfaces per unit
• Increased flexibility
* Check availability** Candidate feature
Benefits
•Operates at Gigabit speeds
•Synchronous Ethernet can be used for eNodeB
RAN
•Optical fibre interfaces offer flexibility
•Scalable solution by concatenating IDUs **
•Up to 16 E1s at an RT location **
•Flexible installation options
10Commercial in confidence
www.cbnl.com Commercial in confidence 11
VectaStar Metro*: product features
• Application: small cell backhaul/ enterprise access/ mixed networks
• Deployment scenario: rooftop/ mast/ wall/ street furniture
• Integrated antenna
• 26, 27 and 28GHz frequency support
• Downlink Low and High supported for all bands
• 7-state hitless adaptive modulation (QPSK up to 256QAM)
• 7, 14, 28MHz channels supported for all bands
• 300Mb/s per sector and up to 300Mb/s per link
• Future proofed Gigabit Ethernet interfaces
• 35W (typical) power consumption
• Range: 2.5km (99.99%, 1E-9 BER, Vertical, London, 28MHz, 16QAM+TCM, typical)
• Dimensions: 306 (w) x 168 (248) (h) x 133mm (d) (typical)
• Weight: 5.4kg (typical, including antenna)
Pictured: VectaStarMetro Access Point and Remote Terminal
– both designed with identical form factors.
Simple mounting bracket allows for rapid installation on
street furniture and building walls
* Check availability
www.cbnl.com Commercial in confidence 12
VectaStar ODU Wideband* (ODU-W) AP & RT: product features
• Application: macro backhaul / enterprise access / mixed networks
• Deployment scenario: rooftop / mast
• 26, 27 and 28GHz frequency support
• Downlink Low and High supported for all bands
• 7-state hitless adaptive modulation (QPSK up to 256QAM)
• 7, 14, 28MHz and 56MHz channels supported for all bands
• Up to 600Mb/s Ethernet throughput per AP (56 MHz@256QAM)
• Up to 600Mb/s Ethernet throughput on one RT
• Up to 4.8Gb/s per Radio Controller
• Ethernet as default configuration (TDM optional)
• Future proofed Gigabit Ethernet interfaces
• Dimensions: 309 x 289 x 110mm (excluding antenna)
• Weight: 4.0kg (typical, excluding antenna)
* Preliminary Data
www.cbnl.com Commercial in confidence 13
VectaStar Metro Wideband* (ODU-MW) AP & RT: product features
• Application: small cell backhaul/ enterprise access/ mixed networks
• Deployment scenario: rooftop/ mast/ wall/ street furniture
• Integrated antenna
• 26, 27 and 28GHz frequency support
• Downlink Low and High supported for all bands
• 7-state hitless adaptive modulation (QPSK up to 256QAM)
• 7, 14, 28 and 56MHz channels supported for all bands
• 600Mb/s per sector and up to 600Mb/s per link
• Future proofed Gigabit Ethernet interfaces
• 35W (typical) power consumption
• Dimensions: 306 (w) x 168 (248) (h) x 133mm (d) (typical)
• Weight: 5.4kg (including antenna) (typical)
Pictured: VectaStar Metro Wideband Access Point and
Remote Terminal –(provisional only).
Simple mounting bracket allows for rapid installation on
street furniture and building walls
* Preliminary Data
VectaStar Configuration App
www.cbnl.com Commercial in confidence 14
• Further accelerates network roll-out by reducing time on site for backhaul installation
• Workflow enforces right-first-time installer practices
• Secure connection to ODU over WiFi dongle (removed post-installation)
• GPS coordinates of ODU set for accurate NMS geographical overview
• Commercially available for iOS platforms (iPad, iPhone)
Search App Store for ‘CBNL’