Power Mac G4 Cube Modem ReplacementInstalling a new Modem.

Written By: Ryan Chun

Power Mac G4 Cube Modem Replacement Draft: 2014-01-28Guide ID: 3384 -

This document was generated on 2019-10-19 03:24:56 AM (MST).

© iFixit — CC BY-NC-SA www.iFixit.com Page 1 of 8

INTRODUCTION

Installing Modem involves removing the outer case and video card before installation.

TOOLS:T10 Torx Screwdriver (1)

Power Mac G4 Cube Modem Replacement Draft: 2014-01-28Guide ID: 3384 -

This document was generated on 2019-10-19 03:24:56 AM (MST).

© iFixit — CC BY-NC-SA www.iFixit.com Page 2 of 8

Step 1 — Outer Case

Release the back handle of the PowerMac. Slowly pull out the cube by holding the end of thehandle. Watch for any parts that may become entangled with the outer case.

Push back the handle after you have taken the core out of the case.

Step 2

Place the cube upside down and remove the four T10 Torx screws on the front plate. Then removethe two screws on each side.

Power Mac G4 Cube Modem Replacement Draft: 2014-01-28Guide ID: 3384 -

This document was generated on 2019-10-19 03:24:56 AM (MST).

© iFixit — CC BY-NC-SA www.iFixit.com Page 3 of 8

Step 3

Slowly lift the plate off the cube anddisconnect the power cord.

Step 4

Remove the four pillars from eachcorner.

The pillars should come out fairlyeasily.

Power Mac G4 Cube Modem Replacement Draft: 2014-01-28Guide ID: 3384 -

This document was generated on 2019-10-19 03:24:56 AM (MST).

© iFixit — CC BY-NC-SA www.iFixit.com Page 4 of 8

Step 5 — Video Card

Remove the screws on the back ofthe VGA port.

Step 6

Remove the screw attaching thevideo card to the logic board.

Power Mac G4 Cube Modem Replacement Draft: 2014-01-28Guide ID: 3384 -

This document was generated on 2019-10-19 03:24:56 AM (MST).

© iFixit — CC BY-NC-SA www.iFixit.com Page 5 of 8

Step 7

Remove power cord from the video card.

Step 8

Remove the power cord.

Remove the connector.

Remove the video card from thelogic board.

Power Mac G4 Cube Modem Replacement Draft: 2014-01-28Guide ID: 3384 -

This document was generated on 2019-10-19 03:24:56 AM (MST).

© iFixit — CC BY-NC-SA www.iFixit.com Page 6 of 8

Step 9

Carefully lift the video card from thelogic board.

The video card should come outeasily.

Step 10

Separate the video card from the adapter.

Power Mac G4 Cube Modem Replacement Draft: 2014-01-28Guide ID: 3384 -

This document was generated on 2019-10-19 03:24:56 AM (MST).

© iFixit — CC BY-NC-SA www.iFixit.com Page 7 of 8

To reassemble your device, follow these instructions in reverse order.

Step 11 — Modem

Remove the two screws from themodem.

Step 12

Lift modem from the Logic Board.

The modem should come out easily.

Power Mac G4 Cube Modem Replacement Draft: 2014-01-28Guide ID: 3384 -

This document was generated on 2019-10-19 03:24:56 AM (MST).

© iFixit — CC BY-NC-SA www.iFixit.com Page 8 of 8