Nuvap ProSystem Nx Series Device User Manual
-
Upload
khangminh22 -
Category
Documents
-
view
0 -
download
0
Transcript of Nuvap ProSystem Nx Series Device User Manual
Nuvap ProSystem Nx Series Device User Manual
3
Index
Introduction .............................................................................................................................. 11
The Nuvap ProSystem Nx Series ................................................................................................ 12
The Device ..................................................................................................................................... 12
Where to Position the Devices ...................................................................................................... 13
Configuration of the ProSystem devices .................................................................................... 14
Requirements for the configuration of the Nx Series devices ...................................................... 14
Preparing the Nuvap Nx device .................................................................................................... 14
Configuration of the Nuvap Nx ..................................................................................................... 14
Notes on the configuration (in case of problems) ........................................................................ 15
Moving the devices ....................................................................................................................... 15
Reconfiguring the devices ............................................................................................................. 16
Using the ProSystem devices ..................................................................................................... 17
Operating mode ............................................................................................................................ 17
Auto-test ....................................................................................................................................... 17
Reset ............................................................................................................................................. 18
Device notifications ...................................................................................................................... 18
Audio Messages ............................................................................................................................ 18
Light signals ................................................................................................................................... 19
Green Signals ............................................................................................................................. 19
Yellow Signals ............................................................................................................................ 19
Red Signals ................................................................................................................................ 20
Blue Signals ............................................................................................................................... 20
Violet Signals ............................................................................................................................. 21
Other Signals ............................................................................................................................. 21
Manual Detection ......................................................................................................................... 21
The Nuvap Application .............................................................................................................. 22
Login .............................................................................................................................................. 22
Register ......................................................................................................................................... 22
Home ............................................................................................................................................ 23
Overview ................................................................................................................................... 23
Electromagnetic Pollution ......................................................................................................... 23
Nuvap ProSystem Nx Series Device User Manual
4
Acoustic Pollution ...................................................................................................................... 24
Radioactivity .............................................................................................................................. 24
Air Quality ................................................................................................................................. 24
Gas ............................................................................................................................................. 25
Water Measurement ................................................................................................................. 25
Add Water Measurement ...................................................................................................... 25
Previous Water Measurements ............................................................................................. 26
Manage N1s .................................................................................................................................. 26
View Existing N1 Devices ........................................................................................................... 26
Add Viewer ................................................................................................................................ 27
Add Device ................................................................................................................................ 27
Scan the QR Code .................................................................................................................. 27
Join to Nuvap Network .......................................................................................................... 27
IP Settings .............................................................................................................................. 28
Language and Mode Settings ................................................................................................ 28
Connect to the Internet ......................................................................................................... 28
Water Quality ................................................................................................................................ 29
Add new Measure ..................................................................................................................... 30
Previous Measure ...................................................................................................................... 31
Punctual Measures ....................................................................................................................... 32
Punctual History ............................................................................................................................ 33
Notifications Setup ....................................................................................................................... 34
Alarms Log .................................................................................................................................... 35
User ............................................................................................................................................... 36
My.Nuvap Platform ................................................................................................................... 37
Login Page ..................................................................................................................................... 37
Create New Account ................................................................................................................. 37
My N1s .......................................................................................................................................... 38
My N1s History .......................................................................................................................... 38
Home ............................................................................................................................................ 39
Settings ......................................................................................................................................... 39
Tools .............................................................................................................................................. 40
Export ........................................................................................................................................ 40
Nuvap ProSystem Nx Series Device User Manual
5
Export List .................................................................................................................................. 40
General Maintenance ................................................................................................................ 41
SW Maintenance ........................................................................................................................... 41
Calibration ..................................................................................................................................... 41
MTBF Nx Series ............................................................................................................................. 41
Cleaning ........................................................................................................................................ 41
Assistance ..................................................................................................................................... 41
Safety Precautions ........................................................................................................................ 42
Operating Limits ............................................................................................................................ 43
Conformity .................................................................................................................................... 43
HW Characteristics ........................................................................................................................ 43
Nuvap ProSystem Nx Series Device User Manual
7
IndexofPictures
Pic 1: Top of the device .................................................................................................................... 13
Pic 2: Water analysis kit .................................................................................................................... 13
Pic 3: QR Code .................................................................................................................................. 13
Pic 4: Power button .......................................................................................................................... 14
Pic 5: Start the measurements ......................................................................................................... 21
Pic 6: Download page ....................................................................................................................... 22
Pic 7: Login page ............................................................................................................................... 22
Pic 8: Register page .......................................................................................................................... 22
Pic 9: Accessing the menu ................................................................................................................ 23
Pic 10: Overview ............................................................................................................................... 23
Pic 11: Electromagnetic pollution ..................................................................................................... 23
Pic 12: Acoustic pollution ................................................................................................................. 24
Pic 13: Radioactivity .......................................................................................................................... 24
Pic 14: Air quality .............................................................................................................................. 24
Pic 15: Gas ........................................................................................................................................ 25
Pic 16: Add water measurements ..................................................................................................... 25
Pic 17: Previous measurements ....................................................................................................... 26
Pic 18: Manage N1s .......................................................................................................................... 26
Pic 19: View settings ......................................................................................................................... 26
Pic 20: Add viewer ............................................................................................................................ 27
Pic 21: Device configuration ............................................................................................................. 27
Pic 22: Connect to Wi-Fi ................................................................................................................... 27
Pic 23: Select Nuvap network ........................................................................................................... 27
Pic 24: Connect to Wi-Fi ................................................................................................................... 28
Pic 25: Language options .................................................................................................................. 28
Pic 26: Wi-Fi password ...................................................................................................................... 28
Pic 28: Green Test Tube .................................................................................................................... 29
Pic 29: White Test Tube .................................................................................................................... 29
Pic 30: Test Strip Type1 .................................................................................................................... 29
Pic 31: Test Strip Type2 .................................................................................................................... 29
Pic 27: Water Quality Menu ............................................................................................................. 29
Nuvap ProSystem Nx Series Device User Manual
8
Pic 32: Water Measurement Step1 .................................................................................................. 30
Pic 33: Water Measurement Step2 .................................................................................................. 30
Pic 34: Previous Water Measurements ............................................................................................ 31
Pic 35: Punctual Measurement Starts .............................................................................................. 32
Pic 36: Punctual Measurements Ends .............................................................................................. 32
Pic 37: Punctual History .................................................................................................................... 33
Pic 38: Notification Setup page1 ...................................................................................................... 34
Pic 39: Notification Setup page2 ...................................................................................................... 34
Pic 40: Alarms Log ............................................................................................................................. 35
Pic 41: User Account page1 .............................................................................................................. 36
Pic 42: User Account page2 .............................................................................................................. 36
Pic 43: Change Password .................................................................................................................. 36
Pic 44: My.Nuvap Login page ........................................................................................................... 37
Pic 45: My.Nuvap Create Account page ........................................................................................... 37
Pic 46: My N1s page ......................................................................................................................... 38
Pic 47: My N1s History page ............................................................................................................. 38
Pic 48: My Nuvap Home page .......................................................................................................... 39
Pic 49: My.Nuvap Settings page ....................................................................................................... 39
Pic 50: My.Nuvap Export page .......................................................................................................... 40
Pic 51: My.Nuvap Export List page ................................................................................................... 40
Nuvap ProSystem Nx Series Device User Manual
9
IndexofIcons
Icon 1: High Frequency ..................................................................................................................... 12
Icon 2: Low-Frequency ..................................................................................................................... 12
Icon 3: Radon Gas ............................................................................................................................. 12
Icon 4: Ionizing Nuclear Radiation .................................................................................................... 12
Icon 5: Wi-Fi Networks ..................................................................................................................... 12
Icon 6: Noise ..................................................................................................................................... 12
Icon 7: Formaldehyde ....................................................................................................................... 12
Icon 8: VOC ....................................................................................................................................... 12
Icon 9: Air Quality ............................................................................................................................. 12
Icon 10: CO ....................................................................................................................................... 12
Icon 11: Relative CO2 ....................................................................................................................... 12
Icon 12: CH4 ..................................................................................................................................... 12
Icon 13: Dust and Smoke .................................................................................................................. 12
Icon 14: Water Quality ..................................................................................................................... 12
Icon 15: Temperature ....................................................................................................................... 12
Icon 16: Humidity ............................................................................................................................. 12
IndexofTables
Table 1: Green Signals table ............................................................................................................. 19
Table 2: Yellow Signals table ............................................................................................................ 20
Table 3: Red Signals Table ................................................................................................................ 20
Table 4: Blue Signals table ................................................................................................................ 21
Table 5: Violet Signals table .............................................................................................................. 21
Table 6: Other Signals table .............................................................................................................. 21
Table 7: Device Characteristics ......................................................................................................... 43
Nuvap ProSystem Nx Series Device User Manual
11
IntroductionThis manual provides the instructions for the set-up and correct use of devices in the ProSystem Nx Series, and the Nuvap Application.
Both the manual and the product described in it are protected by copyright, all rights reserved. The manual therefore may not be reproduced either fully or partially, without written permission from Nuvap.
Nuvap ProSystem Nx Series Device User Manual
12
TheNuvapProSystemNxSeries
TheDeviceThe Nuvap ProSystem Nx Series includes devices for the specific monitoring of the main sources of indoor pollution, which can, over time, be harmful for your health.
The ProSystem Nx devices, together with the relative technology and the techniques used in association with the device, are protected by patents or international patent applications and copyright. Thanks to the device sensors, the ProSystem appliances are able to detect up to 26 different parameters, including the following (depending on the version):
Icon 1: High Frequency Electromagnetic Fields
Icon 2: Low-Frequency Electromagnetic Fields
Icon 3: Radon Gas
Icon 4: Ionizing Nuclear Radiation
Icon 5: Wi-Fi Networks
Icon 6: Noise
Icon 7: Formaldehyde
Icon 8: VOC
Icon 9: Air Quality (H2, LPG, Alcohol, NH3, Ethanol,
Toluene)
Icon 10: CO Carbon Monoxide
Icon 11: Relative CO2 Carbon Dioxide
Icon 12: CH4 Methane
Icon 13: Dust and Smoke
Icon 14: Water Quality (Chlorine, Hardness, Alkalinity,
Ph, Nitrine, Nitrate)
Icon 15: Temperature
Icon 16: Humidity
Nuvap ProSystem Nx Series Device User Manual
13
All the d registered by the ProSystem Nx Series devices are available at anytime and anywhere via the Nuvap App and the My.Nuvap platform.
The Nx ProSystem Series comes with: 1. Status LEDs: Red, Yellow, Green 2. Touch key (on top of the device) (see Pic 1) 3. Loudspeaker for the voice messages (this function can be disabled via the app) 4. 5V DC Connector 5. Test tubes with water analysis kit (for N ° 6 tests) (see Pic 2) 6. QR code with MAC Address number (at the bottom of the device) to activate the services in
App and to request the Calibration Certificate. (see Pic 3)
Pic 1: Top of the device
Pic 2: Water analysis kit
Pic 3: QR Code
WheretoPositiontheDevicesThe Nx Series devices function in environments which have a temperature of between -5 e +40°C and a humidity level of less than 80%.
For the configuration of the devices, a fixing kit is not required, but they should be placed on flat surfaces, at eye level (e.g. desks, office furniture, bookcases). The ProSystem devices are designed to be moved around easily, allowing the measuring of the presence of pollutants in work environments in “roaming”.
The appliances should be placed in rooms where people spend most of their time (offices, meeting rooms, etc.) and away from sources of heat, air-conditioners and extremely dusty environments.
The devices should also be placed far away from electromagnetic sources such as smart phones and cordless phones, Smart-TVs, projectors and from sources of local pollution so as not to not to impair the correct functioning.
It is also recommended that the Nx devices not be placed in environments where there is an elevated quantity of dust (work premises with high dust residues such as carpenters, car workshops, bakeries etc.).
The devices are equipped with a battery that allows up to 3 hours of use. Depending on the characteristics of the environment being monitored (including, for example, ceiling height, number of floors, thickness of the walls, etc.), the devices may not detect significant levels of some parameters (see the FAQ section on the Nuvap website). Generally speaking, to understand the data detected by the device, we recommend that you contact the Nuvap support team when you have been monitoring for a few weeks.
Nuvap ProSystem Nx Series Device User Manual
14
ConfigurationoftheProSystemdevices
RequirementsfortheconfigurationoftheNxSeriesdevicesTo configure the ProSystem devices you need:
• 2.4 GHz 802.11 b/g (40Kb/s minimum band upload) Wi-Fi connection1 • An iOS or Android Smartphone or Tablet • A Nuvap account.
The Nx devices require a Wi-Fi network with WPA PSK authentication and do not support access via WPA Enterprise or catch portal. The internet connection via the Wi-Fi network must not be through proxy and must not filter the HTTP and HTTPS protocols (ports 80 e 443).
The devices use the 80 port to transmit the information via Internet. If this port is inaccessible or the firewall is configured to block it, data transmission is not possible.
PreparingtheNuvapNxdeviceIn order to configure and use the device you must:
1. Remove the device and the power supply from the package; 2. Place it in the environment that you want to monitor; 3. Connect to the electricity supply; 4. Connect the power supply and insert the plug into the socket; 5. Press the power button next to the power connector to switch on
the device; (see Error! Reference source not found.) 6. Download the ‘Nuvap App’ Mobile App from Apple Store (™) or
Google Play (™) 7. Have a Nuvap Account, created automatically on the
my.nuvap.com platform, when you install the App.
ConfigurationoftheNuvapNxThe device acquires the information from the Wi-Fi network at the moment when it is switched on; it is therefore extremely important to switch it on and configure it in an area with a good network coverage.
1. Login from the Mobile App with the credentials provided by the Nuvap account. 2. Select ‘Manage N1s’ from the menu on the left of the app 3. Select ‘Add Device’ 4. Scan the QRCODE that is at the bottom of the device to be configured. (see Pic 3) 5. Follow the guided configuration procedure from the Nuvap App (see section Add Device). 6. Wait for the message: “Continuous Monitoring activated” to appear.
1 It is impossible to install the Nx device without a W-Fi connection.
Pic 4: Power button
Nuvap ProSystem Nx Series Device User Manual
15
If the device has been installed correctly, a few minutes after the installation procedure has been completed, it will transmit the first measurements from the sensors and make them available via the App. If this does not occur, we recommend that you repeat the installation procedure.
In the case of further installations, you simply need to add a new device from the ‘Manage Devices’ area of the App. All the devices that have been installed and are online will be visible on the account.
When the device has been correctly configured, on the App’s main page under the Nuvap Index panel, you will be able to see that the device has been updated (grey writing under the device icon). At this point, the monitoring of the environmental parameters has started, and from this moment, roughly every quarter of an hour, the data will be updated and can be consulted either via the Nuvap App or the My.Nuvap platform (see section My.Nuvap Platform).
The data can be only be visualized by authorized profiles (owners and viewers of the device). The owner of the device can authorize all the viewer users that he likes, provided that they have previously been registered on the my.nuvap.com platform. The viewer profiles, the notifications and the function configurations are managed via the APP by the device’s owner.
Notesontheconfiguration(incaseofproblems)The device is not correctly connected to the Wi-Fi network if it does not transmit the data after a few minutes, or if it sends these messages: “Wi-Fi Password Error” or “IP Address Conflict”.
Any difficulties in configurating the devices can be caused by:
• Entering the wrong Wi-Fi network Password • Presence of a network Firewall that denies access to Nuvap servers • The Nuvap Nx device is too far from the Access Point • The Nx battery is flat or not very charged • A connection problem with the WAN network (if the device is connected to the Wi-Fi network,
but is not updating the monitored data)
MovingthedevicesIf the devices are moved, they may lose the internet connection. If this happens, you must put the device back in the area with Wi-Fi coverage, or reconfigure it in the new environment using the reconfiguration procedures.
The devices can memorize the data acquired even if they are not connected to the network, for up to a maximum of 60 days. To allow the Nx Series device to retransmit all the memorized data to the My Nuvap platform, just bring it back into the zone of the pre-configured Wi-Fi coverage.
The Nx devices have autonomy of around 3 hours, thanks to the built-in back-up battery.
Nuvap ProSystem Nx Series Device User Manual
16
ReconfiguringthedevicesTo reconfigure the device, just follow these easy steps:
1. Switch the ProSystem off and then on again. 2. Keep the touch button pressed with at least two fingers (on the top of the device, with the
Nuvap logo). 3. The status LED will first become purple and then BLUE. In the presence of the BLUE LED
release the touch button. 4. The device will emit three sounds twice and tell you it is ready for a new configuration by
saying “ready - waiting for configuration”. 5. Follow the installation procedure.
Nuvap ProSystem Nx Series Device User Manual
17
UsingtheProSystemdevices
OperatingmodeThe Nx Series devices have three operating modes:
• Continuous mode, • Punctual mode 1 • Punctual mode 2
After the initial configuration of the device, the continuous mode is automatically activated: the device constantly analyses the parameters and regularly updates the global assessment of the quality of the monitored environment2, on the basis of a proprietary algorithm (“NUVAP QUALITY INDEX”). The data and the index can be consulted via the App and the Platform at http://my.nuvap.com.
Locally, at any time, by pressing the touch button, the Nx Series device will return a voice message summarizing the quality of the monitored environment.
A reliable assessment of the quality of the monitored environment requires the use of an Nx Series device in continuous mode, for a period of at least 30 consecutive days. It is possible to know the Nuvap Quality Index of the environment in which the device is installed, at any time, through the App and the Platform, at http://my.nuvap.com.
To pass to the punctual mode, just press the touch button and wait for the violet led.
In the punctual modes, the Nx device supplies the real-time results of the analysis of the environmental quality parameters of the area monitored via the Nuvap App.
In punctual mode 1, the Nx device supplies the real-time results of the analysis of the environmental quality parameters of the area monitored via the Nuvap App. We recommend this mode every time you wish to check a specific environment.
In punctual mode 2, the Nx Series devices supply the reading of one sensor at a time in “live” mode via the Nuvap App, and update the analyzed data every two seconds, producing a graph of the values in real-time.
Auto-testThe Nx series is able to perform an automatic correct operation test at predetermined time intervals. If there are no operating anomalies it emits a green light, which if desired, you can turn off via the App.
In the event of the auto-test detecting operating anomalies, such as for example, problems with the Wi-Fi connection, problems with the battery, broken or uncalibrated sensors etc., the device emits a blue light.
2 The environmental conditions may vary over time.
Nuvap ProSystem Nx Series Device User Manual
18
It is also possible to check the state of the device and any anomalies in the functioning by simply pressing the touch button.
Any information regarding malfunction is also transmitted to the platform, if the network connection functions have not been compromised. It is in any case necessary to calibrate the device at regular intervals to confirm that it is functioning correctly.
ResetIt is possible to reset the Nx Series devices by cancelling all the settings. This operation can be made necessary, for example in the event of modifications in the Wi-Fi network (change of network name and/or password, change of modem, moving the device).
It is not possible to carry out the reset only from the Nuvap App. To carry out the reset and cancel all the data and settings, proceed as follows:
• Switch the device off and switch it on again after a few seconds • Press the touch button and keep it pressed until the Nx device emits a blue light (after around
20 seconds) and then release the touch button. • After a few seconds, Nx will start functioning again, ready for a new configuration. • After the reset, you must follow the initial configuration procedure.
DevicenotificationsThe Nx Series devices can communicate via audio messages, light signals and notifications via App or web platform.
Each device is able to emit two types of audio notification (Attention and Danger), and five types of light signals via its leds (green, yellow, red, blue and violet).
In the event of an Nx device detecting the presence of pollutants at Attention or Danger levels, as well as emitting a local alarm, it sends a notification to the App and the Nuvap platform (http://my.nuvap.com).
AudioMessagesEach device emits two types of audio message to signal the increase in the levels of the pollutants monitored: Attention and Danger3.
The notification that the attention level has been exceeded is to signal the increased levels of one or more of the monitored pollutants before they reach the danger level.
In this case, the Nx device will emit the following message. “Detected presence of (name of pollutant)”. At the same time, the device will emit an intermittent yellow light.
The danger alarm sounds when the level of one or more pollutants reaches the danger level, and higher than the values believed to be healthy. The device emits an alarm and the voice message: "High presence of (name of pollutant)". At the same time, the Nx Series device emits an
3 Voice notifications can be disabled via APP
Nuvap ProSystem Nx Series Device User Manual
19
intermittent red light. In both cases, the device continues to repeat the voice alarm signal and the light signal until it is deactivated by pressing the touch key on the top of the device.
LightsignalsThe Nx Series devices are able to send out five types of light signals:
• Green signal: occurs periodically or on request, (Touch) and signifies that the device is functioning properly and there are no anomalies or pollutants detected. (see Green Signals table)
• Yellow signal: occurs in the event of detection of higher levels of one or more of the pollutants monitored before they reach the danger threshold (“ATTENTION”). Simultaneously emits the voice message: “Presence of (name of pollutant)”. (see Yellow Signals table)
• Red signal: occurs when the level of one or more pollutants reaches the threshold of danger, (DANGER). The device simultaneously sounds the alarm and the voice message: “Danger, high presence of (name of pollutant)”. (see Red Signals Table)
• Blue signal: warns about malfunctions, for example, problems with Wi-Fi connection, battery, sensors. The same blue signal can be seen during the start/reset phase of the Nx Series devices. (see Blue Signals table)
• Violet signal: indicates that punctual measurement has started. (see Violet Signals table)
GreenSignalsVoice Message What It Means What You Should Do
Continuous measuring started
The device has started to monitor the environment in a continuous manner
Wait for the messages on the state of the monitored environment
No pollutants detected in the monitored area
The device did not detect any pollutants in the monitored area after the measurement in Punctual mode
Do nothing
Quality of the monitored environment Excellent / Good / Insufficient
The device indicates that the monitored environment has an Excellent / Good / Insufficient quality
See the complete measurements carried out by the device through the NUVAP App
or Platform. (http://my.nuvap.com)
Table 1: Green Signals table
YellowSignalsVoice Message What It Means What You Should Do
Presence of Particulates or smoke
The device has detected the presence of Smoke or
particulate matter at ATTENTION levels
See the entry for the pollutant on www.nuvap.com/en/solutions
Presence of Ionizing nuclear
radiation
The device has detected the presence of Ionizing nuclear radiation at
ATTENTION levels
See the entry for the pollutant on www.nuvap.com/en/solutions
Wi-Fi networks detected The device has detected the presence of Wi-Fi networks at ATTENTION levels
See the entry for the pollutant on www.nuvap.com/en/solutions
Presence of Radon Gas The device has detected the presence of Radon Gas at ATTENTION levels
See the entry for the pollutant on www.nuvap.com/en/solutions
Presence of Carbon Monoxide
The device has detected the presence of CO at
ATTENTION levels
See the entry for the pollutant on www.nuvap.com/en/solutions
Presence of Formaldehyde The device has detected the presence of Formaldehyde at ATTENTION levels
See the entry for the pollutant on www.nuvap.com/en/solutions
Nuvap ProSystem Nx Series Device User Manual
20
Voice Message What It Means What You Should Do Presence of Carbon
dioxide The device has detected the presence of Carbon dioxide at ATTENTION levels
See the entry for the pollutant on www.nuvap.com/en/solutions
Presence of VOC The device has detected the presence of VOC at
ATTENTION levels
See the entry for the pollutant on www.nuvap.com/en/solutions
Quality of the monitored environment Excellent / Good / Insufficient
The device indicates that the monitored environment has an Excellent / Good / Insufficient quality
See the complete measurements carried out by the device through the NUVAP App or
Platform. (http://my.nuvap.com)
Table 2: Yellow Signals table
RedSignalsVoice Message What It Means What You Should Do
Danger, high level of Electromagnetic Fields
NX has detected a high presence of Electromagnetic Fields
See the entry for the pollutant on www.nuvap.com/en/solutions
Danger, high level of Magnetic Fields
NX has detected a high presence of Magnetic Fields
See the entry for the pollutant on www.nuvap.com/en/solutions
Danger, high presence of noise
NX has detected a high presence of Noise
See the entry for the pollutant on www.nuvap.com/en/solutions
Danger, high presence of air pollutants
NX has detected a high presence of air pollutants
See the entry for the pollutant on www.nuvap.com/en/solutions
Danger, high presence of Particulates or Smoke
NX has detected a high presence of Particulates or Smoke
See the entry for the pollutant on www.nuvap.com/en/solutions
Danger, high presence of Ionizing Nuclear Radiation
NX has detected a high presence of Ionizing Nuclear Radiation
See the entry for the pollutant on www.nuvap.com/en/solutions
Danger, high presence of Wi-Fi networks
NX has detected a high presence of Wi-Fi networks
See the entry for the pollutant on www.nuvap.com/en/solutions
Danger, high presence of Radon Gas
NX has detected a high presence of Radon Gas
See the entry for the pollutant on www.nuvap.com/en/solutions
Danger, high presence of Carbon Monoxide
NX has detected a high presence of Carbon Monoxide
See the entry for the pollutant on www.nuvap.com/en/solutions
Danger, high presence of Formaldehyde
NX has detected a high presence of Formaldehyde
See the entry for the pollutant on www.nuvap.com/en/solutions
Danger, high presence of carbon dioxide
NX has detected a high presence of carbon dioxide
See the entry for the pollutant on www.nuvap.com/en/solutions
Danger, high presence of VOC
NX has detected a high presence of VOC
See the entry for the pollutant on www.nuvap.com/en/solutions
Quality of the monitored environment Excellent / Good / Insufficient
The device indicates that the monitored environment has an Excellent / Good / Insufficient quality
See the complete measurements carried out by the device through the NUVAP App or
Platform. (http://my.nuvap.com)
Table 3: Red Signals Table
BlueSignalsVoice Message What It Means What You Should Do
Is starting up Wait for the start up Ready awaiting configuration
The device is awaiting configuration Configure the device (see chapter Add Device)
Fatal Error Generic error Switch the device off and on again. If the message is repeated, reset the device
(see section Reconfiguring the devices). Visit www.nuvap.com/en/support for
information Please wait The device cannot perform the Wait. The device will perform the required
Nuvap ProSystem Nx Series Device User Manual
21
Voice Message What It Means What You Should Do requested action manually action as soon as it is ready
Low battery The device signals the battery level below the minimum threshold
Connect the device to the power supply. Visit www.nuvap.com/en/support for information.
Wi-Fi password error The Wi-Fi password is wrong Reset the device (see section Add Device) and repeat the configuration.
Wi-Fi IP Conflict The device reports a conflict of IP addresses on the network
Reconfigure the device with a different free address. Visit www.nuvap.com/en/support for
information.
Table 4: Blue Signals table
VioletSignalsVoice Message What It Means What You Should Do
Punctual measuring started
The device has started to monitor the environment in a punctual mode
Wait for the message of end of punctual measuring with the relative state of the
environment monitored
Table 5: Violet Signals table
OtherSignalsVoice Message What It Means What You Should Do
For details access data on Nuvap application
The device recommends viewing the data recorded on
NUVAP App
See complete measurements carried out by the device through the NUVAP App or
Platform. (http://my.nuvap.com)
Table 6: Other Signals table
ManualDetectionPress the touch key (see Pic 5) to perform the manual operational test. Press the touch key located on the top of N1 and listen to the message: “No pollutants were detected in the monitored area”.
View all data monitored by your N1, through Nuvap App, anytime and anywhere you are.
Pic 5: Start the measurements
Nuvap ProSystem Nx Series Device User Manual
22
TheNuvapApplicationThe Nuvap Application, which can be found in Apple stores (™) and Google (™) is essential for the configuration of the Nx series devices.
LoginIn this section you can Login and create a Nuvap Account with your e-mail address and password (see Pic 6).
Execute the application and press register (see Pic 7) to create your Nuvap account.
RegisterInsert your name, surname, email and password to identify yourself in the Nuvap system. Accept Privacy Policy and press Register (see Pic 8).
After registering your user you can enter the Nuvap application.
Pic 6: Download page
Pic 7: Login page
Pic 8: Register page
Nuvap ProSystem Nx Series Device User Manual
23
HomeThe main menu can be accessed by clicking on the symbol, located on the top left. From this menu it is possible to reach all the available data and functions (see Pic 9).
The first screen you can see when executing the application is the home screen with the summary of the latest measurements in graphical mode.
Pic 9: Accessing the menu
OverviewIn this screen we can see an overview of the environment in which we have installed the N1 device (see section Where to Position the Devices). The current condition is described with many ways (see Pic 10):
• Text (ex. GOOD) • Number from 1 to 10 • Color from red to green
If we press anywhere in this area we can see a measurement variance chart from the day we install the N1 device up to date.
Pic 10: Overview
ElectromagneticPollutionThe factors that the N1 device measures are described as follows (see Pic 11):
• High frequency with warning signal on 3 V/m and alert signal on 6 V/m.
• Low frequency with warning signal on 3000 nT and alert signal on 10000 nT.
• WiFi with warning signal on 15 networks and alert signal on 20 networks.
If we press anywhere in these areas we can see a measurement variance chart from the day we install the N1 device up to date for each of these factors.
Pic 11: Electromagnetic pollution
Nuvap ProSystem Nx Series Device User Manual
24
AcousticPollutionThe factor that the N1 device measures is described as follows (see Pic 12):
• Noise with warning signal on 70 db(spl) and alert signal on 85 db(spl).
If we press anywhere in this area we can see a measurement variance chart from the day we install the N1 device up to date.
Pic 12: Acoustic pollution
RadioactivityThe factors that the N1 device measures are described as follows (see Pic 13):
• Radon with warning signal on 100 Bq/m3 and alert signal on 300 Bq/m3.
• Radioactivity with warning signal on 0.387 uSv/h and alert signal on 0.95 uSv/h.
If we press anywhere in these areas we can see a measurement variance chart from the day we install the N1 device up to date for each of these factors.
Pic 13: Radioactivity
AirQualityThe factors that the N1 device measures are described as follows (see Pic 14):
• Temparature with no warning or alert limits. • Hunidity with no warning or alert limits. • Air pollutants with warning signal on 20 % and alert
signal on 83 %. • Smoke/Particulate with warning signal on 250 ug/m3
and alert signal on 500 ug/m3.
If we press anywhere in these areas we can see a measurement variance chart from the day we install the N1 device up to date for each of these factors.
Pic 14: Air quality
Nuvap ProSystem Nx Series Device User Manual
25
GasThe factors that the N1 device measures are described as follows (see Pic 15):
• Methane with warning signal on 500 ppm and alert signal on 8000 ppm.
• CO with warning signal on 10 ppm and alert signal on 29 ppm.
• Carbon Dioxide with warning signal on 1500 ppm and alert signal on 1858 ppm.
• Formaldehyde with warning signal on 0.2 ppm and alert signal on 0.75 ppm.
• VOC with warning signal on 313 ppB and alert signal on 3130 ppB.
If we press anywhere in these areas we can see a measurement variance chart from the day we install the N1 device up to date for each of these factors.
Pic 15: Gas
WaterMeasurementIn this section you can view and add water measurements with the water kit that is attached to dhe N1 device. For more details you can refer to the Water Quality section.
AddWaterMeasurementYou can add new measurements by pressing the corresponding button and inserting the value (see Pic 16) of the colorimetric comparison chart kit for water analysis found at the bottom of the N1 device (see Pic 2). The factors that the N1 device measures are described as follows:
• Hardness • Chlorine • Alkalinity • Ph • Nitrites (mg/L) • Nitrates (mg/L)
You must repeat this test every six months.
Pic 16: Add water measurements
Nuvap ProSystem Nx Series Device User Manual
26
PreviousWaterMeasurementsYou can see the previous measurements (see Pic 17) by pressing the corresponding button.
Pic 17: Previous measurements
ManageN1sIn this screen you can either view or change the existing N1 devices by selecting them from the top of the page or you can add an extra N1 device (see Pic 18).
Pic 18: Manage N1s
ViewExistingN1Devices By selecting this option you can view or edit your current settings of an N1 device such as:
• Name of the device • Language used • Enable/Disable silent mode • Allow/Disallow alarms • Viewer of this application
You can always dissociate an N1 device from your environment by pressing the existing button (see Pic 19).
Pic 19: View settings
Nuvap ProSystem Nx Series Device User Manual
27
AddViewerBy pressing the Edit button on the upper right corner of the screen you can add an extra viewer of this application (see Pic 20). As an extra edition to the previous screen comes the add viewer option where you must insert a valid Nuvap account name (see section Register).
Pic 20: Add viewer
AddDeviceIn this section you can start the configuring the ProSystem device.
To access, select Manage N1 from the drop-down menu and then select ADD N1. You should then scan the QRCODE on the bottom (see Pic 3) of the device that you want to configure and then follow the instructions from the App.
ScantheQRCodeThe first step is to scan the QR Code that is located under the N1 device (see Pic 21).
JointoNuvapNetworkYou must connect N1 to the internet via WiFi. Press the button to go the Wi-Fi settings (see Pic 22). Once you have selected the Wi-Fi option the App will tell you to connect to the Wi-Fi network’s4 SSID created by the device you are configuring with a name like: “NUVAP_F8F0XXXXXXXX”. The device creates a unique Nuvap Wi-Fi Network (see Pic 23). You must select it and return to the previous screen.
Pic 21: Device configuration
Pic 22: Connect to Wi-Fi
Pic 23: Select Nuvap network
4 With some operating systems, this network can be detected 'without internet connectivity'. Despite this, access must be allowed.
Nuvap ProSystem Nx Series Device User Manual
28
IPSettingsThe second phase in the configuration process is connecting your Smartphone/Tablet to the Wi-Fi network generated by the ProSystem device (see Pic 24).
Select the Wi-Fi option from the configuration screen. You can select other types of connectivity available for different models. If you prefer, instead of choosing the DHCP option, you can give an IP address.
LanguageandModeSettingsYou can set more options of the N1 device such as language and silent mode (see Pic 25).
ConnecttotheInternetOnce you have selected the network created by the device from the networks available on your Smartphone or tablet, you must return to the Nuvap App.
Insert the data necessary for the connectivity (SSID and Wi-Fi network password where you want to register the ProSystem device, or alternatively the APN) and select “CONNECT” (see Pic 26).
Pic 24: Connect to Wi-Fi
Pic 25: Language options
Pic 26: Wi-Fi password
Nuvap ProSystem Nx Series Device User Manual
29
WaterQualityIn this section you can view previous water measurements and you can also add a new water analysis measurement. You can choose between adding a new measurement and view previous measurement (see Pic 27).
In order to do so you must use the water analysis kit attached to the bottom of the N1 device (see Pic 2).
The water analysis kit consists of the following items:
• Green Test Tube (see Pic 28): contains a number of test Strips type1 (see Pic 30).
• White Test Tube (see Pic 29): contains a number of test strips type 2 (see Pic 31).
• Test Strip Type1 (see Pic 30): we can measure the parameters of Hardness, Chlorine, Alkalinity and Ph of the sample water.
• Test Strip Type2 (see Pic 31): we can measure the parameters of Nitrites and Nitrates of the sample water.
Test Tubes Water Analysis Strips
Pic 28: Green Test Tube
Pic 29: White Test Tube
Pic 30: Test Strip Type1
Pic 31: Test Strip Type2
Pic 27: Water Quality Menu
Nuvap ProSystem Nx Series Device User Manual
30
AddnewMeasureWe select the Water Quality option in the Nuvap application. Then choose the "Add new measure" option. We fill the test tubes with the sample water and then we insert the test strips in each of the test tubes for one minute. The Nuvap application shows the Colorimetric Comparison Chart in order to select the appropriate values.
We hold the Type1 strip upside down (as shown in Pic 32) and we select (click) the appropriate value from the table for each row for the parameters of Hardness, Chlorine, Alkalinity and Ph of the sample water.
We then hold the Type2 strip (as shown in Error! Reference source not found.) and we select (click) the appropriate value from the table for each row for the parameters of Nitrites and Nitrates of the sample water.
We save the data and we return the main screen of the N1 device.
Water Measurement Step 1 Water Measurement Step 2
Pic 32: Water Measurement Step1
Pic 33: Water Measurement Step2
Hold Strip from Here Hold Strip from Here
Nuvap ProSystem Nx Series Device User Manual
31
PreviousMeasureIn this section we can see the previous water analysis measurements. The screen is shown in Error! Reference source not found. and we can see the values for each of the measured parameters along with a relative state of the parameter.
We must repeat this test every six months in order to monitor with accuracy our water supplies.
Pic 34: Previous Water Measurements
Nuvap ProSystem Nx Series Device User Manual
32
PunctualMeasuresWith this function you can perform manually a complete test of your environment.
When you select this function the application prompts you to press the touch key located on the top of the N1 device until a violet signal5 lights the device (see Pic 35). You can hear the message: "Accurate Measurement has Started" from the N1 device. During this phase you will be prompted to join the N1 WiFi network (see Join to Nuvap Network) in order to update the cloud with the results of this action.
At the end of the measurements the device will announce the relative state of the environment monitored and the N1 data of the device will be updated in your application (see Pic 36).
Pic 35: Punctual Measurement Starts
Pic 36: Punctual Measurements Ends
5 see Violet Signals
Nuvap ProSystem Nx Series Device User Manual
33
PunctualHistoryWithin this section you can view all the measurements that have been made by the N1 device during the Punctual Measurement procedure (as described previously in Punctual Measures).
By selecting this option you can view all the data that have been measured ordered by the date that the punctual measurement had been taken (see Pic 37).
Pic 37: Punctual History
Nuvap ProSystem Nx Series Device User Manual
34
NotificationsSetupIn this section you can set on and off all the audio and visual alarms of the N1 device. You can start by selecting from the drop down list the N1 device you want to setup.
You can turn on and off all 15 different parameters (as seen in Pic 38 and Pic 39):
Electromagnetic Pollution
Acoustic Pollution
Radioactivity Gas Air Quality
High Frequency
Noise
Radon
Methane
Humidity
Low Frequency
Radioactivity
CO
Air Pollutants
Wi-Fi
CO2
Smoke/Particulate
Formaldehyde
Possibility of Fire
VOC
Pic 38: Notification Setup page1
Pic 39: Notification Setup page2
Nuvap ProSystem Nx Series Device User Manual
35
AlarmsLogIn this section you can view all the alarm history of the N1 device. The alarm log is ordered by the date of the alarm descending from the newest to the oldest date (see Pic 40).
Pic 40: Alarms Log
Nuvap ProSystem Nx Series Device User Manual
36
UserIn this section you can view and edit all the personal information of your account such as (see Pic 41 and Pic 42):
• Application Language • Account Details such as: Name, Surname, Email and Phone Number • Address Details such as: Street, ZIP code, City, State/Province and Country
Pic 41: User Account page1
Pic 42: User Account page2
Pic 43: Change Password
You can also change your current password by pressing the Change Password button at the end of the screen where you must enter your old password once and your new password twice as seen above (see Pic 43).
Nuvap ProSystem Nx Series Device User Manual
37
My.NuvapPlatformMy.Nuvap is a cloud platform devoted to collect the data monitored by Nuvap Nx devices and enable multiple actions such as:
• Account management • Device Management • Device History Management • Dashboard (Nuvap Index) • Notifications Management • Download Data
LoginPageThis is the starting page of My.Nuvap environment (www.my.nuvap.com).
You can either insert your credentials or create o new account.
After inserting your credentials you can press the confirm button (see Pic 44)
Pic 44: My.Nuvap Login page
CreateNewAccountIn case you don’t have an account in Nuvap cloud environment you can create one (see Pic 45) by clicking the appropriate button in the login page.
You must enter:
• First name * • Middle name • Last name * • E-mail * • Password * • Phone number • Address • Personalized assistance
(*) Compulsory data field
Pic 45: My.Nuvap Create Account page
Nuvap ProSystem Nx Series Device User Manual
38
MyN1sThis is the first page after the login page in which you can choose between all available N1 devices. (see Pic 46)
This page is always available from the “MY N1s” link shown on the top side of every Nuvap page.
Pic 46: My N1s page
MyN1sHistoryIn this page you can see all the data collected from the chosen N1 device.(see Pic 47)
You can select any record by pressing the appropriate pencil icon on the right side of each line and then see the measurements of the specific date.
This page is always available from the “MY N1s History” link shown on the top side of every Nuvap page.
Pic 47: My N1s History page
Nuvap ProSystem Nx Series Device User Manual
39
HomeThis is the Home page in which you can see the summary of the latest measurements of the chosen device. (see Pic 48). On the left side you can navigate between the different factors that are measured (see section The Device) You can select any of these factors in order to see a more detailed chart. This page is always available from the “Home” link shown on the top side of every Nuvap page.
Pic 48: My Nuvap Home page
SettingsBy selecting the gear icon on the top right side on the menu you can view the IP and SSID settings and you can modify or see the following settings of the chosen device (see Pic 49) :
• You can modify the user list. • You can dissociate the chosen
N1 device. • Show the full log. • Show the full ownership log. • Show the latest
measurements. • Show the punctual
measurements log.
Pic 49: My.Nuvap Settings page
Nuvap ProSystem Nx Series Device User Manual
40
ToolsIn the tools section that you can access through the top right link in the upper right corner of the Home page with the name “TOOLS”.
ExportWith this option (see Pic 50) you can export data for a specific date range, MAC address or N1 device.
After inserting the criteria you can press the Export button to complete the procedure.
Pic 50: My.Nuvap Export page
ExportListIn this page (see Pic 51) you can view all the exports that you have done via the previous stage.
Pic 51: My.Nuvap Export List page
Nuvap ProSystem Nx Series Device User Manual
41
GeneralMaintenance
SWMaintenanceNo update procedure is required as the devices are always automatically updated to the latest firmware version available.
CalibrationThe ProSystem Devices are accompanied by a calibration certificate, lasting one year. The devices can be re-calibrated annually at the Nuvap laboratories.
MTBFNxSeriesLike all devices with sensors, the ProSystem Devices have a limited life-span. The Nx series is designed to operate for a period of about 4 years from its first activation, under normal use and suitably maintained conditions. At the end of this period, some of the sensors may no longer function properly. Contact Nuvap customer support to ensure you have regular and reliable checks.
CleaningDo not spray water or detergent directly onto the surface. The direct spraying of water or detergent can cause fire, electric shock, damage to the product surface or removal of warning labels. Do not apply chemicals containing alcohol, solvents or surfactants such as wax, benzene, thinners, pesticides, air freshener, lubricants or soap. These chemicals can cause discoloration or cracking of the frame or remove the labels. Use a clean sponge or chamois cloth dampened with a solution of nonabrasive detergent and a few drops of warm water; then wipe with a soft, dry cloth.
The ProSystem devices have a built-in rechargeable lithium battery with autonomy of up to hours without power and in conditions of normal use. It cannot be replaced and its duration is the same as the device’s. In any case, in the event of battery malfunction, the device will emit a blue signal.
AssistanceFor technical assistance, please refer to NUVAP’s Customer Support. More information on Authorized Assistance numbers is available on the website www.nuvap.com/en/support. Unauthorized repairs may invalidate your product’s warranty.
Nuvap ProSystem Nx Series Device User Manual
42
SafetyPrecautionsTo ensure a correct use of the product and for your own personal safety please stick to all the rules and instructions given here. For anything not described in this manual, please refer to our website www.nuvap.com/en/support.
• DO NOT expose the device to direct sunlight, heat, flames or water. To do so may cause malfunction or fire.
• DO NOT put the device in dusty or dirty spaces. • DO NOT use the device near liquids and DO NOT expose it to rain or damp. • In the event that the device gets wet, unplug the power cord and wait for the device to dry
completely before you turn it back on. Do not try to dry with an external source of heat, like a microwave oven or hair dryer. Dry it with a soft cloth.
• DO NOT use strong solvents such as benzene or other chemicals on or near the surface of the Nx Series device.
• DO NOT place the device on unstable worktops. • DO NOT hold the device on your lap or any other part of your body. • Make sure that the device does not come into contact with objects that can scratch or
damage it. • DO NOT place or drop objects on the device and do not shove any object into it. • DO NOT spill any food or drink on it. • ALWAYS DISCONNECT THE POWER SUPPLY before cleaning • Dropping the product may result in malfunction or breakage. When carrying the device
around you should keep it in the original packaging. • Keep the device out of children’s reach. • DO NOT UNDER ANY CIRCUMSTANCES attempt to open the device: do not dismantle, try to
repair or adjust the product. Opening or attempting to dismantle the device will compromise its operativity and will void your warranty.
• DO NOT cover the device while it’s functioning, as this will reduce air circulation and affect its functions.
• Do not expose the device to heat or cold. For example, do not leave it in the boot of the car at high temperatures or below zero.
• DO NOT throw the device in waste bins. The product has been designed to allow the components to be reused and the materials to be recycled. Make sure you dispose of or recycle the device in accordance with local laws and regulations regarding the disposal of electronic products. For further information regarding the recycling of Nx Series devices, please consult the website: www.nuvap.com/en/support.
• IMPORTANT: USE ONLY THE POWER SUPPLY PROVIDED. It is obligatory to use a shielded power cord, in order to meet emissions limits imposed by current regulations, and to prevent interference with radio or television reception.
Nuvap ProSystem Nx Series Device User Manual
43
OperatingLimits• The Nx ProSystem devices have been designed for use in indoor environments. • The Nx ProSystem devices should not be considered as substitutes for complete alarm
detection of pollutants in places that are home to large numbers of people, such as residential hotels and dormitories.
• Should you need to transport the device by plane, please check with the airline if specific rules exist.
• The devices might not detect the presence of pollutants if these do not reach its detection range.
• The device is not able to intervene in any way on the presence of pollutants in the environment being monitored.
• SAFE TEMPERATURE: the device should be used in temperatures of between -5 ° C (25 ° F) and 40 ° C (105 ° F).
NUVAP declines any responsibility in the event of accidents or damage to people or property not directly due to intrinsic defects of the product.
NUVAP CANNOT BE HELD LIABLE TO THIRD PARTIES FROM USES OF THE DEVICE OTHER THAN THOSE SPECIFIED HEREIN.
ConformityNUVAP Srl, under its sole responsibility, declares that this product complies with the essential requirements of Directive R&TTE 1999/5/CE, of European Directives 2006/95/CE, 2004/108/CE and 1999/5/CE.
NUVAP states that the following standards and/or specifications have been applied: EN 300 328, EN 301 489-1, EN 301 489-17. EN 55022, EN 55024, EN 61000-3-2 ed EN 61000-3-3.
A copy of the Declaration of Conformity for the European Union can be found at: www.nuvap.com
Nuvap will issue a calibration certificate for the device upon request and presentation of the MAC address, or the device’s QR code.
HWCharacteristics CPU 100 MHz - 32 bit - FPU FLASH MEMORY 2 MB SDRAM 8 MB STORAGE MEMORY 4 GB POWER SUPPLY 5V DC BATTERY Li-ion 3.7VDC 2200 mAh DIMENSIONS 18,3 x 18,3 x 8,4 cm CONNECTIVITY Wi-Fi – 2,4 GHz REPORTING APPS Nuvap App & Nuvap Platform my.nuvap.com WEIGHT 780 gr.
Table 7: Device Characteristics