Hardware.pdf - TVC Communications

66
www.tvcinc.com Section 4: Hardware Table of Contents (888)644-6075 4 - 2 Aerial Cable Damper .......................................... 4 – 3 Anchors .............................................................. 4 – 4 Arms & Braces ................................................... 4 – 7 Bolts ................................................................... 4 – 8 Brackets & Straps ............................................... 4 – 10 Clamps ............................................................... 4 – 18 Clips ................................................................... 4 – 31 Dead End & Splices ............................................ 4 – 36 Eyes ................................................................... 4 – 40 Grounding Materials ............................................ 4 – 41 Guy Hardware ..................................................... 4 – 52 Guy Markers ....................................................... 4 – 54 Lashers ............................................................... 4 – 56 Lashing Wire / Strand .......................................... 4 – 58 Molding ............................................................... 4 – 59 Pole Steps .......................................................... 4 – 60 Screws ................................................................ 4 – 61 Spacers ............................................................... 4 – 63 Staples ................................................................ 4 – 64 Tree Guards ........................................................ 4 – 65 Washers & Nuts ................................................. 4 – 66 Magic Mile .......................................................... 4 – 67

Transcript of Hardware.pdf - TVC Communications

www.tvcinc.com

Section 4: Hardware

Table of Contents

(888)644-60754 - 2

Aerial Cable Damper .......................................... 4 – 3Anchors .............................................................. 4 – 4Arms & Braces ................................................... 4 – 7Bolts ................................................................... 4 – 8Brackets & Straps ............................................... 4 – 10Clamps ............................................................... 4 – 18Clips ................................................................... 4 – 31Dead End & Splices ............................................ 4 – 36Eyes ................................................................... 4 – 40Grounding Materials ............................................ 4 – 41Guy Hardware ..................................................... 4 – 52Guy Markers ....................................................... 4 – 54Lashers ............................................................... 4 – 56Lashing Wire / Strand .......................................... 4 – 58Molding ............................................................... 4 – 59Pole Steps .......................................................... 4 – 60Screws ................................................................ 4 – 61Spacers............................................................... 4 – 63Staples ................................................................ 4 – 64Tree Guards ........................................................ 4 – 65Washers & Nuts ................................................. 4 – 66Magic Mile .......................................................... 4 – 67

www.tvcinc.com

Section 4: Hardware

Aerial Cable Damper

(888)644-60754 - 3

Diamond’s Aerial Cable Damper is designed to use the force of the wind to aerodynamically reduce themovement and oscillation of aerial cable. Intended for use on aerial cables of 18 to 150 pairs. • A.C. Damper plate is made of high-grade aluminum alloy with 25,000 psi tensile strength.

• Lashed cable supports are made of corrosion resistant stainless steel with 80,000 psi tensile strength.• “D” lashing clamps are made of high quality steel mechanically galvanized to meet ASTM specification

B695.

Diamond’s A.C. Damper Kit Consists of the Following:1 pc. A.C. Damper Plate.2 pc. Stainless Steel lashed cable supports, 16" lg. (34–08922)3 pc. “D” Lashing clamps (26–09010) Installation sheet enclosed.

Cable Guards are not included due to variable cable sizes which can be accommodated.

Installation1. Select proper size cable guard for application.2. Place guard on cable over horizontal slots in A.C. Damper.3. Insert lashed cable supports through horizontal slots. Use two wraps and secure by bending end over top

of buckle. Allow 1/4" clearance between cable and top of A.C. Damper. *A.C.D. must be allowed to swingfree with the wind.

4. Position lashing clamps inside lashed cable supports and secure. Lashing clamps will restrict longitudinalmovement to cable area protected by cable guards.

5. Placement – The number of A.C.D’s varies with length of cable span and terrain. The following isrecommended as a guide for maximum effectiveness.

Level Ground – Locate at span’s center for 125–170' Spans (Fig. 1). On spans 170–300' Locate twoA.C.D.’s each one fourth the total span length from either pole. (Fig. 2)Steep Grade – Locate one tenth total span length from pole at lower level on 125–170'spans. (Fig. 3)On spans 170–300' two A.C.D.’s are required. Locate one at one fourth the total spanlength from lower pole. Locate second A.C.D. halfway between first A.C.D. and uphillpole. (Fig. 4)*Note – When installing on Fig. 8 cable A.C.D. should be secured to exposed strand.

Ordering Information Part No. Carton Qty. Wt ea (lbs)

• 28-80001 ................................ 5 ............................ 1.6

www.tvcinc.com

Section 4: Hardware

Anchors

(888)644-60754 - 4

PowerShaft CAM ACTION® AnchorsNo–Wrench Cam Action® Screw Anchors

These anchors can be installed either manually or with power driven equipment. Manual installation isaccomplished by inserting a bar through the eye and screwing the anchor down. Installations with portable orvehicle mounted installing equipment is accomplished by means of adapters. The eye dimensions are the same asshown on the Threaded Forged–Eye.

Ordering Information

Expanding Anchors*Black Painted (Less Rods)

The multi-blade, one-piece top plate expands upon impact into undisturbed earth to form a cone shaped square,which distributes the anchor’s holding power over a wide area, building up compression against an invertedpyramid of earth. The expanding anchor retains its shape under extremely heavy loads because the base platesupports the blades in the middle and distributes the load uniformly over the blades. Reinforcing ribs provideadditional strength.

Ordering Information

Part No. Description Approx. Wt. (lbs. Ea)

J6524WCA 4" Helix, 3/4" x 54" Shaft 8.1J6526WCA (E)* 6" Helix, 3/4" x 66" Shaft 10.9

J6528WCA* 8" Helix, 1" x 66" Shaft 19.1J653OWCA 10" Helix, 1–1/4" x 66" Shaft 30.3J655OWCA 10" Helix, 1–1/4" x 8' Shaft 41.1J6585WCA 16" Helix, 1–1/4" x 8' Shaft 52.0

Tripleye® Helix–Shaft® Assemblies Hot Dip Galvanized

*Thimbleye® shaft add suffix "-1+ (E) REA Accepted

Part No. (in.) Area(Sq. in)

Rod Size (in)(Order

Separately)

Approx.Wt (lbs. Ea)

J0870 (E) 6 70 1/2 or 5/8 5J8115 (E) 8 115 5/8 or 3/4 9J8135 (E) 8 135 5/8 or 3/4 10J8135-1 8 135 1 10J8200-1 (E) 10 200 1 19J8200-3/4 10 200 5/8 or 3/4 19J0283 12 300 1-1/4 33J0283-1 12 300 1 33

Add Suffix G for hot dip galvanized anchors (E) REA Accepted*Expanding anchors are furnished with 8 blades except catalog Nos J0283 / J0283-1 which come with 6 blades

www.tvcinc.com

Section 4: Hardware

Anchors

(888)644-60754 - 5

PartNo.

Approx.Wt. (lbs ea)

PartNo.

Approx.Wt. (lbs

ea)

PartNo.

Approx.Wt. (lbs

ea)

5/8 16,000 5 J7415 5.46 J7416*(E) 6.4 J7516* 6.57 J7417*(E) 7.5 J7517*(E) 8.08 J7418*(E) 8.0 J7518*+(E) 8.4

3/4 23,000 7 J7427 11.0 J7527* 11.0 J7327* 11.28 J7428*(E) 12.5 J7528*(E) 12.4 J7328* 12.59 J7429 (E) 14.0 J7529+(E) 14.0 J7329*+ 14.310 J7430 (E) 15.0 J7530 (E) 15.7

J7538 (E) 22.9 J7338* 22.0J7540*+(E) 28.4 J7340*+ 27.0

1-1/4 58,000 10 J7350+ 44.0* ANSI Standard +Bell Standard (E) REA Accepted

Thimbleye® Twineeye® Tipleeye®

RodDia (in)

Min UltimageStrength Rating (lbs)

Length(ft)

Eye Dimensions

A B C D R A B C D R A B C D R RR

1/2 9/16 1/2 1-1/16 1-7/16 9/165/8 11/16 9/16 1-1/2 1-11/16 11/16 15/16 1/4 1-13/16 1-23/64 11/163/4 13/16 11/16 1-5/8 1-7/8 3/4 1 1/4 1-31/32 1-5/8 11/16 1-9/16 1/4 2-5/8 1-7/16 19/32 5/81 1-1/8 15/16 2 2-1/16 13/16 1-1/4 5/16 2-3/8 1-3/4 11/16 1-9/16 1/4 2-23/32 1-5/8 11/16 21/32

1-1/4 1-9/16 1/4 2-15/16 1-7/8 27/32 13/16

y

Dimensions (In.) Dimensions (In.) Dimensions (In.)RodDia (in)

Threaded Forged-Eye Anchor RodsHot Dip Galvanized

Joslyn forged Thimbleye, Twineye and Tripleye anchor rods are used for guying with expanding, cross plate andcone anchor as well as “Deadman” log anchor assemblies. All rods are threaded 3-1/2" and are assembled with aheavy square nut.

Ordering Information

www.tvcinc.com

Section 4: Hardware

Anchors

(888)644-60754 - 6

Part No. RodDia. (in)

RodLength

(in)

Anchor SizeClosed (in)

Anchor SizeExposed (in)

HoleSize 9in)

Approx.Wt. (lbs ea)

J3436(E) 3/4 15 1-3/4 2-3/8 1-7/8 5J3437(E) 3/4 30 1-3/4 2-3/8 1-7/8 7J3438(E) 3/4 53 1-3/4 2-3/8 1-7/8 10JR360 3/4 60 1-3/4 2-3/8 1-7/8 11JR372 3/4 72 1-3/4 2-3/8 1-7/8 12JR384 3/4 84 1-3/4 2-3/8 1-7/8 13JR396 3/4 96 1-3/4 2-3/8 1-7/8 15JR115L 1 15 2-1/4 3-1/8 2-3/8 10JR130L 1 30 2-1/4 3-1/8 2-3/8 14JR153L 1 53 2-1/4 3-1/8 2-3/8 18JR172L 1 72 2-1/4 3-1/8 2-3/8 24JR184L 1 84 2-1/4 3-1/8 2-3/8 26JR196L 1 96 2-1/4 3-1/8 2-3/8 29

Rock AnchorsHot Dip Galvanized (Complete with Rods)

The malleable iron expanding rock anchor fits into a hole 1-7/8" or 2-3/8" in diameter, expands and wedges firmlyagainst solid rock. When the anchor is expanded, the greater the pull on the rod, the harder the anchor becomeswedged. No lead, concrete or grouting equipment is necessary. Furnished complete with 3/4" and 1" rods, 15" to 8'in length. Anchors are painted black and the rods are hot dip galvanized.

Ordering Information

www.tvcinc.com

Section 4: Hardware

Arms & Braces

(888)644-60754 - 7

Cable Extension Arm

These Cable Extension Arms are used to support a cable at a distance from the pole.The messenger cable is held by a standard J1096 suspension clamp which is bolted upagainst the underside of the two angles by a 5/8" machine bolt. This machine bolt is fittedbetween the legs of the two angles and can be adjusted for proper extension from thepole. Mounting is accomplished by a 5/8" or 3/4" machine bolt at the upper position andtwo 1/2" lag screws at the lower. Mounting bolts and suspension clamp must be orderedseparately.

Ordering Information

Extension Arm

The all steel model 1175 extension arm is zinc plated to prevent corrosion. Eight inches of vertical pole clearanceare required for installation. It can be installed on all type of poles. Slots are provided for banding to cement, steel,or fiberglass poles. For mounting to wood poles, standard bolt holes are available for use of 5/8" thrubolt and two1/2" x 4" drive type lag bolts, not supplied.

Ordering Information

Fiberglass Cable Extension Brackets

Cable Extension Brackets that provide adequate support for communication cables placed some distance fromthe pole to provide the desired clearance. The cable is attached by a standard PA268 or PA273 suspension clampwhich is secured to the bolt in the end casting by a 5/8" nut. Fiberglass rods used in the brackets with ourcastings are also manufactured under stringent specifications. All rods are coated with a polyurethane enamel forultra violet protection. Brackets of the 7562-5 Series are available in any length required.

Ordering Information

Part No.

Angle Size (In.)

Extension FromCenter of Pole

(in.)

Approx.Shipping Weight(lbs. per 100 pcs.)

J7920+ 3 x 2-1/2 x 1/4 17-1/2 - 26 2,900J7921+ 3-1/2 x 2-1/2 x 5/16 26-1/2 - 44-1/2 6,000

Part No. Length Max. Load (lbs.)

Vert. and HorizStd. Pkg.

Wt. Ea.(lbs.)

1175-12 12" 350 2/ctn. 5.51175-18 18" 250 2/ctn. 6.61175-24 24" 200 2/ctn. 9.31175-36 36" 300 2/ctn. 14

PartNo.

Pole M ountingBolts

M ounting BoltSpacing

Fibe rglassRod Dia.

Pole to Clam pClearance

Shipping WPer 100 Pie ces

Std. Pkg.Qty.

EB-512 5/8" 6" & 8" 1-1/2" 12" 738 lbs. 5EB-518 5/8" 6" & 8" 1-1/2" 18" 812 lbs. 5EB-524 5/8" 6" & 8" 1-1/2" 24" 886 lbs. 5EB-530 5/8" 6" & 8" 1-1/2" 30" 960 lbs. 5EB-536 5/8" 6" & 8" 1-1/2" 36" 1034 lbs. 5

www.tvcinc.com

Section 4: Hardware

Bolts

(888)644-60754 - 8

Bolts, CarriageHot Dip Galvanized

Joslyn carriage bolts are roll threaded with square shoulder and square nut. Manufactured in accordance withANSI standards.

Ordering Information

Bolts, Double ArmingHot Dip Galvanized

Joslyn Double Arming Bolts are roll threaded, with cone points at both ends for easy driving and removal withoutdamage to threads. Manufactured in accordance with ANSI standards. “D.A.” bolts are furnished with four squarenuts and are available with static-proof washer nuts. Other lengths are also available. Length dimensions do notinclude the points.

Ordering Information

Part No.

BoltLength

(in.)

ThreadLength

(in.)

Approx.Shipping Wt.

(lbs per 100 pcs)J8634*+(E) 4 3 16.2J8634–1/2*+(E) 4–1/2 3 16.4J8635*(E) 5 3 1 7.6J8635–1/2(E) 5–1/2 3 20.0J8636*+(E) 6 3 21.6J8637 7 3 24.0J8638+ 8 3 26.4J8640 1 0 3 32.0

3/8" Diameter–Minimum Tensile Strength 4,250 lbs.

Part No.

BoltLength

(in.)

ThreadLength

(in.)

Approx.Shipping Wt.

(lbs per 100 pcs)J8644–1/2*(E) 4–1/2 3 34.3J8645*(E) 5 3 35.3J8646+*(E) 6 3 40.5J8647 7 4 44.0J8648 8 4 51.0*ANSI Standard, + Bell Standard, (E) REA Accepted

1/2" Diameter–Minimum Tensile Strength 7,800 lbs.

Part No.w/4 Sq. Nuts

Bolt Length(in.)

Approx.Shipping Wt.

(lbs. per 100 pcs.)J8860 10 118J8862*(E) 12 136J8864*(E) 14 142J8866*(E) 16 158J8868*(E) 18 187J8870*(E) 20 192J8872*(E) 22 208J8874*(E) 24 224J8876 26 240J8877 28 256J8878 30 264J8879 32 284

5/8" Diameter–Minimum Tensile Strength 12,400 lbs.

*ANSI Standard, (E) REA Accepted

Part No.w/4 Sq. Nuts

Bolt Length(in.)

Approx.Shipping Wt.

(lbs. per 100 pcs.)J8882* 12 196J8884* 14 220J8886* 16 240J8888* 18 260J8890*(E) 20 284J8892*(E) 22 304J8894*(E) 24 336J8896 26 345J8897 28 365J8898 30 386

3/4" Diameter–Minimum Tensile Strength 18,350 lbs.

*ANSI Standard, (E) REA Accepted

www.tvcinc.com

Section 4: Hardware

Bolts

(888)644-60754 - 9

Bolts, MachineHot Dip Galvanized Square Head and Square Nut

Joslyn machine bolts are roll threaded. Bolts 1/2" and larger in diameter and 7" and longer in length also have conepoints which permit driving without damage to the threads. Manufactured in accordance with ANSI standards.Other lengths and 1" diameter machine bolts available on special order in production quantities.

Ordering Information

Bolts, Thimbleye®

Hot Dip Galvanized

Joslyn Thimbleye® bolts are forged in two styles, straight and bent at a 45° angle. They are used for attachingguys and deadends to poles and crossarms, eliminating the need for thimbles, strain plates, guyhooks and extra strand.Eye Dimensions are the same as for Thimbleye® anchor rod. Bolt length is measured frombelow the eye to the last thread. All Thimbleye® bolts have cone points and are roll threaded,except for the J22551 which has a gimlet point. 5/8" diameter bolts have a minimum ultimatestrength of 12,400 lbs; 3/4" bolts have a minimum ultimate strength of 18,350 lbs.

Ordering Information

Straight TypePart No.

Approx.Shipping Wt.

(lbs. per 100 pcs.)

Angle TypePart No.

Approx.Shipping Wt.

(lbs. per 100 pcs.)

BoltDia. (in.)

BoltLength

(in.)

ThreadLength

(in.)J8050 (E)+ 124 J8150*(E)+ 130 5/8 8 4J8051*(E)+ 142 J8151*(E)+ 144 5/8 10 4J8052*(E)+ 160 J8152*(E)+ 162 5/8 12 6J8053+ 172 J8153*+ 184 5/8 14 6J8054*+ 186 J8154+ 206 5/8 16 6J8055+ 204 — — 5/8 18 6 — — J8161 (E)+ 216 3/4 10 4 J8062 (E)+ 228 J8162 (E)+ 240 3/4 12 6J8063+ 256 J8163+ 264 3/4 14 6*ANSI Standard, + Bell Standard, (E) REA Accepted

PartNo.

Bolt Length

(in.)

Thread Length

(in.)

Approx.Shipping Wt(lbs. per 100

pcs.)J8806*+(E) 6 3 62.0J8807 (E) 7 4 72.0J8808* (E) 8 4 82.0J8809 (E) 9 4 88J8810* (E) 10 6 94.1J8812* (E) 12 6 108.0J8814* (E) 14 6 125.0J8816* (E) 16 6 136.0J8818* (E) 18 6 152.0J8820* (E) 20 6 170.0J8822 (E) 22 6 184.0J8824 (E) 24 6 200.0*ANSI Standard + Bell Standard (E)REA Accepted

5/8" Diameter–Minimum Tensile Strength 12,400 lbs.

PartNo.

Bolt Length

(in.)

Thread Length

(in.)

Approx.Shipping Wt

(lbs. per 100 pcs.)J8908* (E) 8 4 118.0J8910* (E) 10 6 142.0J8912* (E) 12 6 162.0J8914* (E) 14 6 188.0J8916* (E) 16 6 212.0J8918* (E) 18 6 228.0J8920 (E) 20 6 252.0J8922 (E) 22 6 268.0J8924 (E) 24 6 296.0J8926 (E) 26 6 316.0

3/4" Diameter–Minimum Tensile Strength 18,350 lbs.

www.tvcinc.com

Section 4: Hardware

Brackets & Straps

(888)644-60754 - 10

Trap Sleeve Bracket

DIAMOND’s CATV Trap Sleeve Bracket is designed to mount up to eight (8) trap sleeves to the strand.

• Made of high quality steel and aluminum.• Steel parts are galvanized to meet ASTM specifications A153 and B695.• “W” Bracket and Adapter Plate supplied with captive mounting hardware. Both can be mounted to Slotted Tap Bracket (optional) or Standard 1020A Tap Bracket. (29-19943).• Nuts supplied with external tooth lock washers to prevent loosening.• Windowed flanges on “W” Bracket permit Trap identification from ground if clear trap sleeves are used.• Adapter Plate can be supplied with a longer captive bolt and nut to permit the addition of a

second level adapter plate and two additional “W” Brackets for an eight sleeve version.• Adapter Plate and “W” Bracket have anti-rotational features.• Spring Steel “W” Brackets include snap-in feature suitable for most trap security sleeves

(7/8' to 1- 1/8' diameter).• Trap sleeves are balanced on strand whether 2, 4 or 8 sleeve versions are used.

Ordering Information

Drop Wire Mast Bracket

DIAMOND’s D.W. Mast Bracket provides a means of securing drop wire to service mast.

• “U” Bolt clamp range is 2-1/2" to 3" DIA.• Bracket strap made of high quality 80,000 psi steel.• “U”- Bolt (5/16" - 18 x 3-1/2") plated and chromated per ASTM B633.• Drop wire hook’s load capacity exceeds 700 lbs. Formed from high quality 80,000 psi steel.• Drop wire hook riveted to bracket strap.• Hook and strap mechanically galvanized to meet ASTM specifications A153 and B695.

Ordering Information

Corner Wall Bracket

Corner wall bracket used to dead-end a messenger drop cable or a steel strand at the building.

Ordering Information

Catalog # Description Carton(Qty)

Weight Per(100 pcs. lbs.)

29-90900 Large “W” Bracket 25 1429-90910 Small “W” Bracket 25 1329-90920 Tap/Trap Bracket 25 14

Catalog No.

Carton (Qty)

Weight(100 pcs. lbs.)

40-00540 50 43.5

Catalog No. Specifications Standard

Pkg Qty

Approx.wt./pkg (lbs.)

Approx.wt./pkg

(kg) SC53-1 For steel strand MDU riser 50 14 6.4

SC53-2 For messengered drop cable with .051" to .073" steel messenger wire 50 17 7.7

www.tvcinc.com

Section 4: Hardware

Brackets & Straps

(888)644-60754 - 11

Service Mast BracketHot Dip Galvanized

The J0590 Service Mast Bracket is used with a service wedge clamp to attach the neutral wire of drop cable to theservice mast. The front strap is rounded to prevent damaging the bail of the service wedge clamp. This bracketclamps to 1-1/4" to 3" pipe. A specially designed slot on the end of the front strap permits installation of the bracketwithout removing the bolts, then captures the square carriage bolt shoulder to prevent it from turning or slipping outafter installation. The J26158 Service Mast Bracket provides the same application as the J0590, but the J26158 canalso be used with a telecommunications drop wire clamp. This bracket will also clamp to 1-1/4" to 3" pipe.

Ordering Information

Part No. (App. Ship Wt. Lbs per 100 pcs)• J0590 .............................................. 105

Cable Support BracketHot Dip Galvanized

The J8236 Cable Support Bracket is for use with self-supporting rural telephone cable. It is attached to the pole withtwo 3/8 x 4" lag screws on straight runs and angles of less than 35°. For corner pulls and on angles of more than35°, a 3/8" carriage bolt is substituted in the lower hole.

Ordering Information

Part No. (App. Ship Wt. Lbs per 100 pcs)• J8236+ ............................................220 + Bell Standard

www.tvcinc.com

Section 4: Hardware

Brackets & Straps

(888)644-60754 - 12

House Bracket

• Made of 3/16" thick high quality steel.• Mechanically galvanized to meet ASTM specification B695.• Drop attachment mounting hole is 7/16" diameter.• Bracket has three (3) 9/32" diameter mounting holes which will accommodate #12

wood screws or 1/4" diameter machine screws for a secure mounting in varioussurfaces.

• Suitable for multi-dwelling residential drops or for commercial applications.• May be used for attachments or as a standoff.• Bracket’s legs measure 3-7/16" (house side) by 2-7/8". Width is 1-3/4".

The DIAMOND House Bracket is a sturdy, secure customer premise drop cable bracket. It is recommended forapplications where standard drop attachments are inadequate.

Ordering Information

Tap Bracket

DIAMOND’s Aluminum Tap Bracket is used in CATV drop installation to secure a tap to messenger strand when itcannot be attached directly. The unit is offset below the strand preventing cable abrasion on the equipmenthousing.

Features• 2-1/2" size (distance between strap and tap).• Bracket and clamping plates are made of high grade aluminum alloy with 45,000 psi tensile strength.• Bolt and nut are made of high tensile strength steel. Mechanically galvanized to meet ASTM specifications

A153 and B695.• Square hole in bracket prevents bolt rotation when the nut is tightened.• Tap mounting hole accepts up to a 5/16" bolt (max.).• Designed for 1/4" (6.6M) and 5/16" (6M) messenger strand.• Bent top edge of bracket prevents bolt rotation when the nut is tightened.• Interlocking clamping plate assures a positive and secure grip on the messenger strand.

Ordering Information

Catalog No.

CartonQty

Weight Per100 pcs. (lbs.)

40-00200 50 90

Catalog No. Length Carton

QtyWeight Per

100 pcs. (lbs.)Clamp Type

29-19941 2-1/2" 25 33 One Piece29-19943 2-1/2" 25 20 Two Piece29-19944 9" 25 24 Two Piece29-19945 25 Two Piece

www.tvcinc.com

Section 4: Hardware

Brackets & Straps

(888)644-60754 - 13

Two Hole Straps

DIAMOND Two Hole Straps are used in telephone, CATV and other utility installations to support and secure cable,wire, conduit and pipe to telephone poles, wood, masonry, or various types of walls.

• Made of high quality steel.• Galvanized to resist corrosion.• Clamps available in a full range of sizes to accommodate diameters of 9/16" to

4".• Clamp feet are offset 5° to facilitate mounting on round poles.• REA accepted.• Used as standard by all major telephone companies and throughout

the telecommunications industry.

Ordering Information

Dead-end Strap

Dead end strap made of high quality G90 pre-galvanized steel used to dead-end a drop cable at the house servicemast.

Ordering Information

A B C* E25-80902 1/4 13/32 5/8 9/16 5/8 500 1.625-81102 3/8 9/16 3/4 11/16 5/8 250 225-81302 – 11/16 3/4 13/16 3/4 250 2.825-81602 – 7/8 7/8 1 3/4 300 5.225-82002 1 1-1/16 1 1-1/4 3/4 100 625-82402 – 1-5/16 1 1-1/2 3/4 50 7.225-83002 1-1/4 1-5/8 1-1/8 1-7/8 7/8 50 1025-83602 – 2 1-1/8 2-1/4 7/8 75 13.625-84202 2 2-3/8 1-1/8 2-5/8 7/8 50 15.625-85602 3 1-1/4 1 3-1/2 1 50 22.425-86402 3-1/2 3-1/2 1-1/4 4 1 50 24.8

*Same As Cable Size

CatalogNo.

NearestPipe Sizes

(in.)

Carton(Qty)

WeightPer 100

pcs. (lbs.)

Dimensions

Catalog No. Specifications Standard

Pkg QtyApprox.

wt./pkg (lbs.)Approx.

wt./pkg (kg.) SC11 From 1" to 4" diameter mast 200 40 18.1

SC11T Telephone application, adjustable from 1" to 4" mast 200 36 16.3

www.tvcinc.com

Section 4: Hardware

Brackets & Straps

(888)644-60754 - 14

Bands

Bands in Type 201 stainless steel have been the industry standard for over 54 years. Type 201 stainless steel hassuperior yield and tensile strength properties to provide maximum clamping strength. All bands sizes feature fullyrounded smooth edges for safety and easy installation. For clamps of even greater strength, use a double wrap,threading the Ear-Lokt Buckle each time around.

Ordering Information

Giant Bands

Giant Bands are available in Type 201 stainless steel or galvanized carbon steel. It is used for heavy-duty clampingapplications. Giant 1-1/4" band in 201 stainless steel has a breaking strength of 5,500 lbs. Double wrapped clampsare recommended for maximum strength.

Ordering Information

Type 316 Bands

Type 316 is specified for use in situations where corrosion is the major problem. Type 316 stainless steel is anaustenitic chromium-nickel stainless with excellent corrosion resistant properties. It is used extensively in moistatmospheres and environments where it is subject to chemicals, salts, acids, and high temperatures. Inquire aboutthe availability of Bands in other materials - Inconel, Titanium, and Hastalloy.

Ordering Information

inches mm inches mm lbs. kgMAR204 C204 13204 1/2" 12.70 .030" .76 5.1 2.4MAR205 C205 13205 5/8" 15.88 .030" .76 6.4 3.0MAR206 C206 13206 3/4" 19.05 .030" .76 7.7 3.6

MarathonPart No.

Type 201 Stainless Steel (100' Per Roli - 30.5mm)Width Thickness WeightBand-It

Part No.UICNo.

inches mm inches mm lbs. kgMAR430 G430 17430 3/4" 19.05 .044" 1.12 11.6 5.4MAR431 G431 17431 1" 25.40 .044" 1.12 13.7 6.4MAR432 G432 17432 1-1/4" 31.75 .044" 1.12 17.2 8.0

inches mm inches mm lbs. kgMAR434 G434 17434 1" 25.40 .048" 1.14 15.3 6.9MAR435 G435 17435 1-1/4" 31.75 .048" 1.14 19.1 8.6

Marathon Part No.

Weight

Weight

Band-ItPart No.

UICNo.

Band-ItPart No.

UICNo.

Width Thickness

Type 201 Stainless Steel - 100' Per Roll - (30.5mm)

Galvanized Carbon Steel

Width ThicknessMarathon Part No.

inches mm inches mm lbs. kgMAR404 C404 13404 1/2" 12.70 .030" .76 5.1 2.4MAR405 C405 13405 5/8" 15.88 .030" .76 6.4 3.0MAR406 C406 13406 3/4" 19.05 .030" .76 7.7 3.6

MarathonPart No.

Type 316 Stainless Steel - 100' Per Roll (30.5mm)

Available in mill coil lengths.

Band-ItPart No.

UICNo.

Width Thickness Weight

www.tvcinc.com

Section 4: Hardware

Brackets & Straps

(888)644-60754 - 15

Buckles

Ear-Lokt Buckles in Type 201 stainless steel are designed to accommodate both single and double wrap clamps.The unique teeth and ears provide for maximum clamping strength.

Ordering Information

Giant Buckles

Giant Buckles, Ear-Lokt, are offered in widths and metals to correspond to Giant Band. Giant clamps may be doublewrapped for extra strength.

Ordering Information

Type 316 Buckles

Type 316 Ear-Lokt Buckles are designed to accommodate both single and double wrap clamps to correspond withthe use of Type 316 or 317L Bands.

Ordering Information

Giant Tool

The Giant Tool must be used to apply heavy duty Giant clamps. Measuring 16-1/2" in length, it is designed to pullup to 6,000 lbs.

Ordering Information

inches mm lbs. kgMAR254 C254 13254 1/2" 12.70 2.1 1.0MAR255 C255 13255 5/8" 15.88 2.4 1.1MAR256 C256 13256 3/4" 19.05 3.7 1.7

Width WeightType 201 Stainless Steel - Pkg Qty 100

PartNo.

UICNo.

Band-ItPart No.

inches mm lbs. kgMAR440 G440 17740 3/4" 19.05 1.8 .8MAR441 G441 17441 1" 25.40 2.4 1.1MAR442 G442 17442 1-1/4" 31.75 3.2 1.4

Type 20/301Stainless Steel - Pkg Qty 25PartNo.

UicNo.

Width WeightBand-ItPart No.

inches mm lbs. kgMAR454 C454 13454 1/2" 12.70 2.1 1.0MAR455 C455 13455 5/8" 15.88 2.4 1.1MAR456 C456 13456 3/4" 19.05 3.7 1.7

Type 316 Stainless Steel - Pkg Qty 100PartNo.

UicNo.

Width WeightBand-ItPart No.

PartNo.

Band-ItNo.

UICNo. Description

MAR402 G402 17402 Giant Tool. Pkg Qty 1, Weight 11.7 lbs., 5.3 kg

MAR414 G414 17414 Giant Close Quarter Tension Nut, Replaces tool tension handle when space is limited Pkg Qty 1.

www.tvcinc.com

Section 4: Hardware

Brackets & Straps

(888)644-60754 - 16

Strap Tool

A drop forged tool with tensioning capability of over 2,400 lbs. and a built-in cutter.

• Spring loaded gripper lever for improved band tensioning• Friction held cutoff lever with plastic grip for easier operation• Permanent lubrication on the tension screw to extend tool life and

speed clamping• Zinc plated black chromate finish to provide superior corrosion resis-

tance• Spin handle retaining ring to keep parts intact. The BAND-IT Tool is used to apply BAND-IT Bands and

Buckles, strapping and Free-End clamps.

Ordering Information

Bantam Tool

The Bantam Tool C075 is designed for use in light duty banding applications such asinsulation, cable bundling, and sign hanging.

With the unique 3-way handle, the Bantam Tool can be used in the pistol grip position forone-handed tensioning, or in the other positions for two-handed tensioning. It is especiallyuseful in tight areas with minimal access such as in cable bundling aboard ships.

The Bantam Tool is a compact, lightweight, ratchet action tool with a built-in cutter. It has been designed for easyloading and removing of material, and is zinc plated for corrosion resistance. Tension release levers have beenincorporated into the tool design for situations requiring repositioning of the band after tensioning has begun.

Ordering Information

Bantam Strapping Tool

The Bantam Strapping Tool C085 is a less expensive version designed for light dutystrapping applications on flat surfaces with minimal access. It has been designed forquick take-up and tensioning, and is self-contained, requiring no extra tools to com-plete the clamp.

Ordering Information

PartNo.

UICNo. Description

C075 13075 3-way handle version for one-hand pistol grip or two-hand tensioning. 2.6 lbs., 1.2 kg.

BAND-IT®

PartNo.

UICNo. Description

MAR001 13001 The BAND-IT Tool, Pkg Qty1, Weight 4.4 lbs., 2.0 kg

C043 13043 Close Quarter Tension Nut Replaces tool tension handlewhen space is limited. Pkg Qty 1

C006 13006 Tension Screw/Handle Kit. Pkg Qty 1

PartNo.

UICNo. Description

C085 13085 Strapping version for two-hand quick takeup and tensioning. 2.3 lbs., 1.0 kg.

www.tvcinc.com

Section 4: Hardware

Brackets & Straps

(888)644-60754 - 17

Strap, Aerial Support

The DIAMOND Lashed Cable Support is used to strap CATV and telephone cable to the messenger strand inaerial construction.

• Zinc straps are made of flexible, highly polished zinc alloy.• Tensile strength of zinc strap is 25,000 P.S.I.• Thickness of zinc strap is .012".• Stainless steel straps are made of corrosion resistant type (430) steel.• Tensile strength of stainless steel is 80,000 P.S.I.• Thickness of stainless steel is .010".• Unique buckle design, together with tapered end of strap, facilitates easy threading.• Width of all straps is 3/4".• Edges are processed to remove all raised and projecting metal. All edges are smooth and free from burrs.• Free from kinks.• Meets Bell specifications and packaging requirements.• R.E.A. accepted.

DIAMOND Lashed Cable Supports are made of flexible zinc alloy for easy application. They are also available inhighly polished corrosion resistant stainless steel. Lashed Cable Supports are made in lengths varying from 10" to78" to accommodate cables of different diameters.

Ordering Information

Wall Straps

Joslyn Wall Straps are used for guying and deadending messenger strand to building walls. The J7695 and J7696terminate strand at building corners as illustrated. Both are made of 1-3/8 x 11/32" steel with a forged thimbleye.The J7695 has two and the J7696 has three 9/16" diameter holes spaced 8" from center-to-center. The J7692,formed from 1-7/32 x 15/64" steel, is used similarly to terminate strand at a right angle to the building wall. A wirerope thimble is recommended to protect the strand.

Ordering Information

Diameter Circum3408911 3408912 10" 3/4" 2–5/16" 500 2.9 3.73408921 3408922 16" 1–3/16" 3–5/8" 500 4.0 5.73408931 3408932 22" 2" 6–5/16" 300 5.3 7.23408941 3408942 28" 2–5/8" 8–5/16" 300 7.0 9.43408951 3408952 34" 3–1/8" 10" 300 7.9 11.13408955 3408956 45" 4" 12–1/2" 200 10.3 15.03408961 3408962 50" 5" 15-13/16" 200 11.3 16.93408971 3408972 66" 6–1/2" 20–1/2" 200 14.5 22.43408981 3408982 78" 7–1/2" 23" 200 16.9 26.6

Ctn.Aty.

Wt. per 100pcs. (lbs)

Zinc

Wt. per 100pcs. (lbs)Stainless

Max. Cableor BundlePart No.

ZincPart No.

StainlessLength of Strap

PartNo.

OverallLength (in)

Approx. Ship Wt.(lbs. Per 100)

J7695 16-7/8 251J7696 24-3/8 325J7692 8 78

www.tvcinc.com

Section 4: Hardware

Clamps

(888)644-60754 - 18

Stainless Steel Drop Wire Clamp

DIAMOND’s Stainless Steel Drop Wire Clamp is used to support both ends of an aerial service drop span, at themessenger strand and at the building. The clamp is ideally suited for installations within five (5) miles of theseacoast and near oil refineries, chemical plants, steel mills or any areas subject to a corrosive environment.

• Entire clamp made of corrosion resistant stainless steel.• Bail wire made of 85,000 psi stainless steel.• Shell, wedge and shim made of 90,000 psi stainless steel.• Clamp exceeds breaking strength of most drop wires - 555 lbs. tensile strength.• Design meets specifications of all major telephone companies and the telecommunications industry.• Packaging available to Bell and other specifications, assembled or unassembled.• Suitable for usage with most one and two pair aerial service wires (.200" max. height and .300" max. width).• Manufactured in the USA.

Ordering Information

Dual Cable Clamp

The DIAMOND Dual Cable Clamp is used in CATV installations to secure dual drop wire to wood, metal siding ormasonry surfaces. It can also be used to secure 6 pair telephone aerial service wire.

• Made of high quality steel, rather than plastic, for strength and durability.• Mechanically galvanized to meet ASTM specification B695.• Designed to accommodate both RG7 and RG6 coaxial cable.

Also 6 pair Telco drop wire.• Special “non-pinch” lip to prevent damage to jacket.• One hole design to reduce installation cost and provide attractive

installation along base of shingles and siding.• Secure with DIAMOND Drive pins, using a DIAMOND Hammer Drive Tool.• Manufactured in the USA.

Ordering Information

CatalogNo.

BagQty.

BoxQty.

CartonQty.

WeightPer 100 (lbs)

23-88881 – 25 500 1323-88888 – 25 500 1323-88885 2 1 250 13

CatalogNo.

BoxQty.

CartonQty.

Weight Per100 pcs.

(lbs.)

DualCable Size

Telco6 Pr.

22-12121 500 5000 1.0 6 YES22-12127 500 5000 1.3 7 NO

www.tvcinc.com

Section 4: Hardware

Clamps

(888)644-60754 - 19

SC48 Messenger Bonding Clamp

Bonding clamp used to bond a fig. 8 integrated steel messenger cable to a #6 AWG copper ground wire.

Ordering Information

6 Pair Drop Wire Clamp

DIAMOND’s 6 Pair Drop Wire Clamp is used to support both ends of aerial service wire (2 pair or 6 pair) on themessenger strand and at the building.

Specifications• Shell, shim and wedge made of high grade aluminum alloy.• Tail Wire made of high grade stainless steel wire.• DIMPLED SHIM - dimples are positioned along edges of shim to avoid

compression of 6 pair cables with centrally located copper pairs.• Mechanical (tensile) strength exceeds 750 lbs. without cable slippage,

wedge pulling out of shell or cable damage.• Tensile tests conducted to Bell and cable manufacturer’s standards.• Accepts drop wire cable up to .300" high x.500" wide.• Packaging available to Bell specifications or bulk.• Made in the USA.

Ordering Information

Catalog No. Specifications

Std.PkgQty

Approx.wt./pkg(lbs.)

Approx.wt./pkg

(kg)

SC48.1 For 1/4" or .109" steel messenger cable fitted withthree hardened steel pins .104" diameter. 100 18.5 8.4

CatalogNo. Shim Box

Qty.Carton

Qty.Weight Per

100 pcs. (lbs)23-82350 Dimpled 2 Per Bag 500 1123-82351 Dimpled 25 500 11

www.tvcinc.com

Section 4: Hardware

Clamps

(888)644-60754 - 20

Drop Wire Clamp

The DIAMOND Drop Wire Clamp is used to support both ends of an aerial service drop span at the messengerstrand and building.

• Shell, shim and wedge made of high grade aluminum alloy.• Tail wire made of high grade stainless steel.• Used as a standard by major telephone companies and throughout the

Telecommunications Industry.• Mechanical strength of 555 lbs. exceeds break strength of drop wire.• Suitable for most one and two pair aerial service wires. (.200" max. height and .410" max. width.)• Available with standard Bell type shim (perforated with projections) or a new flat shim with holes only. (No

projections.)• Packaging available to Bell specifications.• R. E. A. accepted.

Ordering Information

SC41 Tap Bonding Clamp

Tap bonding clamp used to bond a fig. 8 integrated steel messenger cable to a tap.

Ordering Information

“E” Span Clamp

The DIAMOND “E” Span Clamp is recognized in the telephone industry for its quality anddependability. The clamping plates are made of 1/4" thick, high tensile strength steel.The 3/8" pigtail hook is shaped for absolute retention of the wire loop of the drop wireclamp. This feature eliminates the problem of an attached wire being loosened by windwhip. All parts are corrosion resistant due to DIAMOND’s quality galvanizing process.

Ordering InformationCatalog Carton Weight PerNumber Quantity 100 pcs. (lbs.)

• 27-00865 ................................100 .......................................... 42.5

CatalogNo.

BagQty.

BoxQty.

Ctn.Qty.

Wgt. Per100 pcs.

(lbs.)

ShimType

23-44441 – – 500 623-44444 – 25 500 623-44445 2 - 250 623-44454 – 25 500 623-44455 2 – 250 6

Perforatedw/projections

Flat Shimwith holes

CatalogNo. Specifications

StndPkgQty

Approx.wt./pkg(lbs.)

Approx.wt./pkg

(kg)

SC41-1 For 1/4" or .109" steel messenger cable fitted withthree hardened steel pins .104" diameter. 100 19 8.6

www.tvcinc.com

Section 4: Hardware

Clamps

(888)644-60754 - 21

“F” Span Clamp

Thread the drop wire or distribution cable through the hook. A tree pruner handle is attached to the “F” SpanClamp by means of a special wrench. The clamp is then raised to strand height with the treepruner handle and placed on the strand. Turn the pruner handle from the ground. This willactivate a mechanical clamping action which will secure the clamp to the messenger strand.Once clamp is secured, remove pruning handle by rotating counter-clockwise.

Ordering InformationCatalog Carton Weight PerNumber Quantity 100 pcs. (lbs.)

• 27-00870 ................................50 ........................................... 60.3

TVC “O” Span Clamp

The “O” Clamp is used to support “take-off” at mid span. It includes a two piece aluminumstrand clamp and galvanized hook.

Ordering InformationCatalog Carton/Case Weight PerNumber Quantity 100 pcs. (lbs.)

• A-1 ..........................................50/250 .................................... 9.7

“O” Span Clamps

The DIAMOND “O” Span Clamp is used in CATV installations to provide drop wire take-offs along the span andrelieve tension on the drop wire at this point. The DIAMOND “O” Span Clamp was recently developed for CATVwith the only true “O” configuration in the industry. The clamping plates are made of 4" thick, high grade aluminumalloy to prevent distortion of the plates while being fastened on the messenger strand. The true “O” configurationprovides a stronger curl than the hook design used in other “O” clamps on the market. The “O” designprovides better retention of the drop wire and eliminates the problem of an attached wire beingloosened by wind whip. All of the steel parts are corrosion resistant due to DIAMOND’s qualitygalvanizing process.

Ordering InformationCatalog Carton Weight PerNumber Quantity 100 pcs. (lbs.)

• 27-00860 ................................100 ......................................... 21.5

“C” Span Clamps

The DIAMOND “C” Span Clamp is used in CATV and telephone drop installations to provide drop wire take-offsalong the span and relieve tension on the drop wire at this point. The “C” is also used as a pull off to hold cableaway from obstacles in the line of aerial construction. This application eliminates the use of tree guards.

Ordering InformationCatalog Carton Weight PerNumber Quantity 100 pcs. (lbs.)

• 27-00869 ................................50 ........................................... 24.3

www.tvcinc.com

Section 4: Hardware

Clamps

(888)644-60754 - 22

“Q” Span Clamps

The DIAMOND “Q” Span Clamp was developed primarily for drop installations in the CATV industry. Allcomponents are manufactured from high quality steel and are corrosion resistant due to DIAMOND’s qualitygalvanizing process. The 1/4" pigtail hook has a deep bend for better retention of the drop wire clamp or wire grip.The positive clamping action insures against slippage on the messenger strand, usually caused by vibration orwind dance.

Ordering InformationPart No. Ctn, Qty. Wt Per 100 pcs. (lbs.)

• 27-00185 ................................100 .......................................... 18.3

SC03E “Econospan” Span Clamp

Multi-directional clamp for messengered and non-messengered drop cable used for dead-end or mid-spanapplication.

Ordering Information

SC03EK Stacker Kit

Stacker to SC03E series span clamps for adding more drops.

Ordering Information

SC03E-2G Span Clamp

Span clamp for steel messengered drop cable bonding applications. Unique locking design prevents any partrotation on steel strand.

Ordering Information

CatalogNo. Specifications

StdPkgQty

Approx.wt./pkg(lbs.)

Approx.wt./pkg

(kg)

SC03EK Formed to take a 1" dia. wrap of a steel messengerwire .051" to .073" 100 7 3.2

CatalogNo. Specifications

StdPkgQty.

Apx.wt./pkg(lbs.)

Apx.wt./pkg

(kg)

SC03E-2G For two steel messenger wires .051" to .073"diameter used on 1/4" (6.6 mm) steel strand 75 14 6.4

SC03ET-2G Same as above used on 7/16" (16 mm) steel strand 75 14 6.4

SC03E-3GW For bonding up to three steel messenger wires .051"to .073" diameter used for 1/4" (6.6 mm) steel strand 75 14 6.4

SC03ET-3GW Same as above used on 7/16" (16 mm) steel strand 75 14 6.4

CatalogNo. Specifications

StdPkgQty

Approx.wt./pkg(lbs.)

Approx.wt./pkg

(kg) SC03E Clamp will accept 1/4" (6.6 mm) steel strand 100 16 7.3 S003ET Clamp will accept 7/16" (16 mm) steel strand 100 16 7.3

www.tvcinc.com

Section 4: Hardware

Clamps

(888)644-60754 - 23

SC23GE Span Ground Clamp

Span ground clamp used to dead end at the tap and to bond messenger steel wires.

Ordering Information

One Hole Offset Clamp

Ordering Information

CatalogNo. Specifications

StdPkgQty

Apx.wt./pkg(lbs.)

Apx.wt./pkg

(kg)

SC23GE-2 Common ground for two .051" to .073" messenger steelwires used for 1/4" (6.6 mm) steel strand 32 9 4.1

SC23GET-2 Same as above used for 7/16" (16 mm) steel strand 32 9 4.1

SC23GE-4 Common ground for four .051" to .073" messenger steelwires used for 1/4" (6.6 mm) steel strand 32 10 4.5

SC23GET-4 Same as above used for 7/16" (16 mm) steel strand 32 10 4.5

A B C D E F G23-80403 5/32 7/32 – 5/16 x .048 1/4 1/4 5/32 1-1/16 9/64 3/16 1/4 500 5000 .423-80405 1/4 5/16 – 5/16 x .048 11/32 3/8 5/32 1-3/16 9/64 1/4 9/32 500 7500 .523-80406 5/16 3/8 – 1/2 x .048 7/16 7/16 1/4 1-1/16 7/32 1/4 5/16 500 5000 .923-80407 3/8 1/2 1/8 1/2 x .048 17/32 17/32 1/4 1-1/8 7/32 5/16 3/8 500 5000 1.023-80408 1/2 9/16 1/4 1/2 x .048 5/8 9/16 1/4 1-3/16 7/32 5/16 3/8 500 5000 1.023-80409 5/32 7/32 – 5/16 x .048 1/4 1/4 5/32 11/16 3/16 5/16 1/4 500 5000 .3

Cable InchCatalog

No. Min. Max.

Wt. Per100 pcs.

(lbs.)

Dimensions (in.)Pipe Size (in.)

SizeStock(in.)

BoxQty

Cart.Qty

www.tvcinc.com

Section 4: Hardware

Clamps

(888)644-60754 - 24

A B C D E F24-80003 3/16 – – 1/2 x .035 11/64 3/16 11/32 7/8 7/32 1/16 500 7500 .524-80004 1/4 – – 1/2 x .035 15/16 1/4 11/32 15/16 7/32 1/16 500 5500 .624-80005 5/16 – – 1/2 x .035 19/64 5/16 11/32 1 7/32 1/16 500 5500 .624-80006 3/8 1/8 – 1/2 x .048 11/32 3/8 1/4 1-1/8 7/32 3/32 500 5000 1.024-80007 7/16 – – 1/2 x .048 13/32 7/16 9/32 1-3/16 7/32 1/8 500 5000 1.024-80008 1/2 1/4 3/8 1/2 x .048 15/32 1/2 1/4 1-1/4 7/32 1/8 500 5000 1.224-80009 9/16 – – 1/2 x .048 17/32 9/16 1/4 1-3/8 7/32 3/16 500 500 1.424-80010 5/8 – – 1/2 x .048 19/32 5/8 9/32 1-3/8 7/32 3/16 500 500 1.424-80011 11/16 3/8 1/2 5/8 x .062 41/64 11/16 3/8 1-5/8 9/32 5/32 500 500 2.424-80012 3/4 1/2 – 11/16 x .062 45/64 3/4 3/4 2-1/8 9/32 1/4 500 500 2.924-80014 7/8 – 3/4 11/16 x .062 53/64 7/8 3/4 2-1/4 9/32 5/16 500 500 3.224-80016 1 3/4 – 3/4 x .080 15/16 1 9/16 2-3/8 9/32 1/4 250 250 5.524-80018 1-1/8 – 1 3/4 x .080 1-1/16 1-1/8 9/16 2-3/8 9/32 11/32 250 250 6.124-80020 1-1/4 1 – 7/8 x .115 1-3/16 1-1/4 3/4 2-15/16 9/32 1/2 100 100 11.8

CatalogNo.

NearestPipeSize(in.)

BoxQty

Carton

Qty

Wt. Per100 pcs

(lbs.)

CableSize (in)

NearestE.M.T*

(in.)

SizeStock(in.)

Dimensions (in.)

C D E25-80100 – 1/4 1/2 x .048 7/32 2 7/32 500 1000 2.025-80120 3/4 – 1/16 x .062 3/8 2-1/2 9/32 250 250 4.025-80140 7/6 1/2 11/16 x .062 3/8 2-5/8 9/32 250 250 4.425-80160 1 – 3/4 x .080 3/8 2-7/8 9/32 300 300 7.425-80200 1-1/4 1 7/8 x 1/8 3/8 3-1/8 9/32 100 100 14.025-80260 1-5/8 1-1/4 1/8 x 1/2 3/8 3-5/8 9/32 50 50 17.425-80400 2-1/2 2 1 x 1/8 1/2 5-1/2 11/32 50 50 31.8

CatalogNo.

CableSize(in.)

NearestPipe

Size (in.)

Size Stock(in.)

BoxQty.

Cart.Qty.

Wt. Per100 pcs.

(lbs.)

Dimensions (in.)

One and Two Hole Clamps

These clamps are used in CATV, telephone, LAN, and other utility installations to support and secure cable,wire, conduit and pipe. All clamps are made of high quality steel and are galvanized to resist corrosion. Onehole clamps are available in a full range of sizes to accommodate 3/16" to 1-1/4" cable. Two hole clampsare available in a full range of sizes to accommodate 7/16" to 3-1/2" cable, R.E.A. accepted. Manufacturedin the USA.

Ordering Information

www.tvcinc.com

Section 4: Hardware

Clamps

(888)644-60754 - 25

Cable SuspensionHot Dip Galvanized

Joslyn Cable Suspension Clamps are used with through bolts, which serve as a clamping member, and are shapedto securely grip messenger wire to the pole. A nut and square washer is used between the clamp and the pole toprovide proper spacing. The J1095 is used for light cables and consists of the clamping members only. A 5/8"through bolt tightens the clamp on the wire as well as to the pole. The J1096 and J25088.1 three–bolt clamps areused for heavier cables and are furnished with a 5/8" through bolt hole. The J25088.1 keeper plate is flat.The J26049 three–bolt clamp is also used for heavier cables and is furnished with a 3/4" through bolt hole.

Ordering information

Angle Suspension ClampHot Dip Galvanized

Angle Suspension Clamps have curved ends to prevent damage to the messenger strand when turning small angles.All clamps firmly grip 1/4" to 7/16" diameter strand. They are furnished with two track bolts and a center mountinghole.

Ordering Information

Crossover ClampHot Dip Galvanized

Joslyn Crossover Clamps for CATV or Telephone Cables are used to clamp two messengers where they cross atright angles. The J7930 Drop Forged Clamp sections are 1-1/2" wide and 3-1/4" long. Two 1/2" diameter bolts haveoval shoulders to prevent turning when tightening. The J25564 Clamps are 1-1/2" wide and 3-1/2" long. Two 3/8"diameter carriage bolts and nuts are installed in the square holes of the clamp providing a “locking action.” Uniquecable grooves with a center “dimple” provide superior clamping action.

Ordering Information Part No. For Strand Dia (in.) Approx. Ship Wt. (lbs per 100 pcs)

• J7930 .............................................. 5/16 to 3/8 ............................................. 154• J25564 ............................................ 3/16 to ½ ............................................... 71

PartNo.

NoBolts

Clamp BoltDia (in.)

ClampLength (in)

Mounting Hole Dia. (in)

StrandDia (in)

Appr. Ship Wt(obs per 100 pcs

J1095 1 – 2–1/2 11/16 1/4 to 7/16 67J1096+ 3 1/2 5–3/4 11/16 x 15/16 1/4 to 7/16 180J25088.1 3 1/2 5–3/4 11/16 x 15/16 1/4 to 7/16 175+ Bell Standard

PartNo.

ClampWidth (in)

Clamp BoltDia (in.)

Mounting Hole Dia. (in)

Appr. Ship Wt(obs per 100 pcs

J7901 1–11/16 1/2 13/16 208J7901A 1–11/16 1/2 11/16 210+ Bell Standard

www.tvcinc.com

Section 4: Hardware

Clamps

(888)644-60754 - 26

Figure–8 Three Bolt Suspension Clamp

The DIAMOND Figure–8 Three Bolt Suspension Clamp is used in CATV and telephone aerialconstruction to secure figure–8 aerial cable and multi–pair distribution wire to the pole. This Clamp has a patentedjaw designed to grip the figure–8 messenger through the jacket. This feature eliminates the need to pre–strip thewire, and reduces the possibility of the cable separating from the messenger.The bolts, nuts and lock washers are finished with DIAMOND’s quality galvanizing process for long, rust free life.

• Bolts, nuts and lock washers are made of high tensile strength steel, mechanically galvanized to meetASTM specifications A153 and B695.

• Plates are made of high grade aluminum alloy, with a tensile strength of 45,000 P.S.I.• Clamp will accommodate a 1/2" or 5/8" thru bolt (not furnished).• Patented design allows clamp jaws to penetrate the messenger jacket and grip the bare wire, eliminating

the need to pre–strip the messenger.• R.E.A. accepted.

Ordering Information

Figure–8 Tangent Support Clamps

The DIAMOND Figure–8 Tangent Support Clamp is used in CATV and telephone aerial construction to secure figure–8 aerial cable and multi–pair distribution wire to the pole where cable spans are straight line or around curves.

• Plates and hook are made of high grade aluminum alloy, with a tensile strength of 45,000 P.S.I.• Unique clamping configuration guarantees a positive grip on the messenger without damaging the jacket.• J hook has a smooth, convex inner surface to minimize friction while tensioning the cable.• Eliminates the need to pre–strip messenger.• Reduces the number of rollers required during tensioning.• J hook is designed to dig into pole when tightened, to prevent rotation during tensioning of cable.• R.E.A. accepted.

Ordering Information

Part No.

MessengerSize Range

CartonQty.

Weight Per100 pcs. (lbs.)

28–09610 .109" – .134" 20 78.828–09615 .148" – .250" 20 71

PartNo.

Thru BoltHole Size

Angle ofTangent

MessengerSize Range

CartonQty.

Weight Per100 Pcs (lbs)

28-09500 5/8" 0-15° .148-.250" 25 37.528-09600 1/2" 0-35° .109-.134" 25 23.028-19651 5/8" 0-35° .109-.134" 25 22.5

PartNo.

Thru BoltHole Size Descrip. Carton

Qty.Weight Per

100 Pcs (lbs)45-80013 1/2" J Hook Only 50 11.045-90003 5/8" J Hook Only 50 14.0

www.tvcinc.com

Section 4: Hardware

Clamps

(888)644-60754 - 27

Figure–8 Span Clamp

The DIAMOND Figure–8 Span Clamp is used in CATV and telephone drop installations to provide drop wire take–offsalong a span of figure–8 aerial cable or multi–pair distribution wire, relieving tension on the drop wire at this point. Itis also used as a pull off to hold figure–8 aerial cable or multi–pair distribution wire away from obstacles in the line ofaerial construction. This application eliminates the use of tree guards. This Clamp is a multi–purpose clamp. The 3/8" hook has a deep bend and extended shank to retain a drop wire clamp or wire grip so it cannot slip off. And it hasthe strength required to withstand the stress of pulling the cable or wire away from an obstruction along the cablerun. This multi–purpose design eliminates the need to carry two separate clamps in inventory.

• Hook and nut are made of high quality steel. Mechanically galvanized to meet ASTM specifications A153 and B695.• Through controlled galvanizing, threads are sharp and clean, allowing nut to turn easily.• Plates are made of high grade aluminum alloy, with a tensile strength of 45,000 P.S.I.• Full 3/8" body and thread diameter of hook insures against nut stripping and snapping of bolt.• Tensile strength of steel hook is 75,000 P.S.I.• Clamp will accommodate multiple drops.• R.E.A. accepted.

Ordering Information

Crossover Clamp

The DIAMOND Crossover Clamp is used in telephone and CATV aerial construction to clamp two 1/4" diameterstranded messengers at right angle crossings. This Clamp is designed with a greater clamping area thanconventional crossover clamps to provide more positive clamping action and prevent frictional wear on the messengercables. The symmetrical top and bottom plates are precisely contoured to accept and lock the crossing messengercables.

The DIAMOND Crossover Clamp is partially assembled, with both the top and bottom plates held together by one ofthe bolts. The 3/8" diameter hex head bolts are threaded into tapped holes in the plates, eliminating the handling ofloose nuts. These features minimize the number of components the installer must handle and allow fasterinstallation.DIAMOND’s quality controlled galvanizing allows bolts to be easily turned into the tapped holes and providesmaximum corrosion resistance.

• Made of high quality, heavy duty steel.• Mechanically galvanized to meet ASTM specifications A153 and B695.• Accommodates 1/4" (6.6M) messenger strand.• Tapped holes in plates eliminate handling of loose nuts.• Partially assembled for time–saving installation.• Through controlled galvanizing, threads are sharp and clean, allowing the hex bolts to turn freely during tightening.• Increased clamping area to maximize holding power.• R.E.A. accepted.

Ordering Information Part No. Box Qty. Wt. Per 100 pcs (lbs)

• 29-09970 ............... 25 ........................... 70.0

PartNo.

MessengerSizes

CartonQty.

Weight Per100 pcs. (lbs.)

28–09800 .109" – .134" 50 29.028–09850 .148" – .250" 50 38.5

www.tvcinc.com

Section 4: Hardware

Clamps

(888)644-60754 - 28

Clamps, Cable Suspension, Corner Attachment

Corner attachment clamps are used for angles of 35° to 60°. Accommodates 5/8" diameter pole mounting bolt. Theinner surface is curved with integral spurs for contact stability with the pole. The integral thimble eyes will acceptdeadending devices up to 1/2" diameter.

Ordering Information Part No. Clamp Length (in) App. Ship. Wt. (lbs. Per 100 pcs.)

• P294 ................................................... 6 ........................................................ 209

Cable Lashing Clamp

The DIAMOND “D” & “E” Cable Lashing Clamp is used in CATV and telephone aerial construction to secure lashingwire terminations at any interruption to cable span continuity, or end of lashing wire coil.

The many unique features of the DIAMOND “D” Cable Lashing Clamp have made it the standard of thecommunications industry. The 13/64" clamping plates are made of specially rolled high tensile strength steel. The“E” Cable Lashing Clamp is essentially the same as the “D” clamp except the clamping plates are of one piecedesign for fast clamping.The 1/4" diameter stud bolt, also made of high tensile strength steel, is staked at both ends to prevent loss of nutswhile positioning the clamp prior to tensioning. The stud has a square shoulder at midpoint which mates with asquare hole in the clamping plate. This prevents rotation of the bolt during final tightening of the clamp to themessenger strand prior to retaining the tension of the lashing wire.Two large diameter, heavy duty steel washers are provided to assure permanent attachment of the terminated lashingwire. All parts are corrosion resistant due to DIAMOND’s quality galvanizing process.

• Made of high quality steel.• Galvanized to meet ASTM specifications A153 and B695.• Minimum tensile strength of the clamping plate is 80,000 P.S.I.• Tensile strength of the stud is 3,000 lbs.• Clamping range from 1/4" (6.6M) to 7/16" (16M) messenger strand.• Large diameter, heavy duty steel washers assure permanent attachment of the

lashing wire.• Clamp is manufactured so the square shank on the stud fits a square hole in the clamping

plates to prevent rotation when the nut is tightened.• Used as a standard by all major telephone companies and throughout the telecommunications industry.• R.E.A. accepted.

Ordering Information

PartNo.

BoxQty. Type Weight Per

100 pcs. (lbs.)26–09010 100 D 15.326–09020 100 E 10.8

www.tvcinc.com

Section 4: Hardware

Clamps

(888)644-60754 - 29

Split Bolt Connectors

Guy ClampHot Dip Galvanized

Joslyn Guy Clamps are rolled from carbon steel with straight parallel grooves that will not damage guy strand. Offsetguy clamps are designed to give increased holding strength. The clamping bolts have special shoulders to preventturning when the nuts are tightened.Ordering Information

B-Beam ClampHot Dip Galvanized

The Joslyn J25911 B Beam Clamp is used in conjunction with a 5/8" thimbleye bolt in the application of deadendingstrand to I beams. A clamping screw allows the clamp to be positioned on the beam flange.

Ordering Information Part No. App. Ship. Wt. (lbs.per 100 pcs/)

• J25911+ ...................................................... 75

PartNo.

No.of Bolts

BoltDia (in)

Clamp Length (in)

ClampWidth (in)

For StrandDia. (in)

Approx.Ship. Wt.

Lbs per 100 pcs)

J1061 + 1 1/2 1–1/2 1–9/16 3/16 to 3/8 63J1030 2 1/2 3–3/8 1–9/16 3/16 to 3/8 126J929 3 1/2 4 1–9/16 3/16 to 7/16 160J930* (E) 3 1/2 6 1–9/16 3/16 to 7/16 224J931* (E) + 3 5/8 6 1–21/32 5/16 to 1/2 256

J926 (E) 2 1/2 3–1/4 1–9/16 3/16 to 5/1 6 128J927 (E) 2 5/8 3–15/16 1–21/32 5/16 to 1/2 174 +Bell standard, (E)REA Accepted

Offset Style

Regular Style

• For copper to copper connections• Bolt and nut of high strength corrosion resistant bronze alloy• Pressure bar is copper through 40H; copper alloy is used for 350 kcmil and above• Bolt and nut of hex design up to 350 kcmil• Tested adn listed to U.L 486A requirements

PartNo.

Range of EqualMain and Tap

Ctn.Qty.

Approx.lbs./ctn.

S-4 8 Sol. - 4 Sol. 100 7S-6 10 Sol. - 6 Sol. 100 5S-8 16 Str. - 8 Str. 100 3UL listed

Ordering Information

www.tvcinc.com

Section 4: Hardware

Clamps

(888)644-60754 - 30

B–Strand, Ground Clamp

Joslyn J7956 Clamps are used to bond the cable sheath to the messenger strand. The Clamp bodyis made of 1-1/2" x 3/16" steel with an inside keeper riding on the end of the bolt. The 1/2" bolt canbe removed to place the clamp over the messenger wire.

Ordering Information Part No. App. Ship. Wt. (lbs. per 100 pcs.)

• J7956+ ............................................................ 52

Bronze, Bonding Clamps

Bonding Clamps are available cadmium plated, semi–cadmium plated and plain bronze for a wide variety of jumperapplications. The assembly consists of 2 clamp sections and a 5/16" x 7/8" bronze hex washer head bolt. Oneclamp section is tapped to allow installation with a single wrench.

Ordering Information

Bonding & Grounding Hardware

Bonding Connector for Meter Pan• Meter pan connector designed to provide a bonding connection between the metallic frame of a meter pan

and a copper ground wire.• Its unique design allows a fixed and positive mechanical contact without interfering with the opening of the

meter pan front cover.

Ordering Information

Part No. Description Wire

RangeWt.

(per 100 Pcs.)

K-1 Plated bronze clamp with onebare bronze groove #6 – 1/0 16

K-2 Bronze clamp completely plated #6 – 1/0 16K-3 Bronze clamp – Unplated #6 – 1/0 16KUL Universal bronze clamp UL listed #6 – 1/0 16

Part No. Application SpecificationsSC51-1 CATV For #10/12/14 AWG copper ground wire made of mech. galv. steel B695 yellow chromateSC51-1SS CATV Same as above but made of stainless steelSC51-2 Tel. For #6 AWG copper ground wire made of mech. galv. steel B695 yellow chromateSC51-2SS Tel. For #6 AWG copper ground wire made of stainless steelSC51-TG Tel. For #6 AWG #14 AWG copper ground wireSC51-CF CATV For #10/12/14 AWG copper ground wire made of stainless steelSC51-1BE Tel.* For #6-10 AWG copper ground wireSC51CF-81 CATV For #10-14 AWG copper ground wireSC51CF-85 Tel. For #6-10 AWG copper ground wire

www.tvcinc.com

Section 4: Hardware

Clips

(888)644-60754 - 31

CATV - Aluminum Drop Wire Clip

The DIAMOND CATV Drop Wire Clip is used in drop installations to secure drop wire and commonground wires to either wood or masonry surfaces.

Specifications• Aluminum thickness is .025"• Hole diameter is .209"• Fastening is accomplished by passing a screw through the holes and securing the clip to the structural surface.• The particular grade of aluminum chosen allows for both excellent strength as well as formability around the cable.• Excellent corrosion resistance.• Made in the USA.

Ordering InformationCatalog No. Carton Quantity Weight Per 100 Pcs. (lbs.)

• 40-80365 ...................... 500 .................. .3

“E”,”A”, 2 Pair “E”, Drop Wire Clips

The DIAMOND “E”, “A”, and 2 Pair “E” Drop Wire Clips are used in telephone and CATV drop installations to secure drop wire runs to either wood or masonry surfaces.

Specifications• Made of high quality steel.• Mechanically galvanized to meet ASTM specifications A153 and B695.• Hole diameter is .209" for all clamps.• Tabs of clamps are spread 3/4" apart to facilitate easy insertion of drop wire.• Three transverse ribs in the radius of the clamp provide a positive hold on the drop wire to prevent wear from friction.• The 2 Pair Drop Wire Clamp is an enlarged version of the “E” drop wire clamp designed for use on 2 Pair Drop Cable.• Clamping is accomplished by passing a screw through the pierced tabs and securing the clamp to the fastening surface.• A DIAMOND Plastic Screw Anchor may be used to secure the clamp to masonry surfaces.• The “E” Drop Wire Clamp is used as a standard by all major telephone companies for standard one pair Drop Cable.• R.E.A. accepted.

Ordering Information

CatalogNo. Style Max

Cable SizeBoxQty.

CartonQty.

Weight Per 100 Pcs.

(lbs.)23-80361 “E” .175" x .310" 50 2,000 1.223-80362 “A” .130" x .240" 50 2,000 123-80370 2 PR. “B” .200" x .400" 50 2,000 1.4

www.tvcinc.com

Section 4: Hardware

Clips

(888)644-60754 - 32

6 Pair “E” Drop Wire Clip

DIAMOND’s 6 Pair “E” Drop Wire Clip is used in telephone drop installations to secure drop wire runs to wood ormasonry surfaces.

Specifications• Made in the USA of high quality steel.• Galvanized to meet ASTM specifications A153 and B695.• Hole diameter is .209".• Clamping action occurs as No. 10 screw is secured to

mounting surface.• A DIAMOND Plastic Screw Anchor is recommended to

secure to masonry surfaces.

Ordering Information

“SAXXIT”™ Cable Clip

“Galvalume” steel cable clip used on concrete, mortar, stucco or wood with a Pre-Inserted Self-Tapping Screw or aDrive Pin.

Ordering Information

CatalogNo.

MaxCable Size

BoxQty.

CartonQty.

Weight Per100 Pcs.

(lbs.)23-83361 .300" x .500" 50 2000 1.4

Part Number Specifications

StdPkg.Aty.

Apx.Wt/pkg

(lbs)

Apx.Wt/pkg

(kg)

SC16-19 For 6 mm RG59 cable with no. 8" x 1"1/4" hex head indented “Phillips” 250 2 1

SC16P-19 Same as above, painted* 250 2 1

SC16-26 For 7 mm RG6 cable with no. 8" x 1" screw1/4" hex head indented "Phillips" 250 2 1

SC16P-26 Same as above, painted* 250 2 1

SC16-3Q For 8 mm QUAD cable with no. 8" x 1" screw1/4" hex head indented “Phillips” 250 2 1

SC16P-3Q Same as above, painted* 250 2 1

SC16-411 For 10 mm RG11 cable with no. 8" x 1" screw1/4" hex head indented “Phillips” 250 2 1

SC16P-411 Same as above, painted* 250 2 1 SC16DP-19 For 6 mm RG59 cable with a 1" drive pin 250 2 1 SC16DPP-19 Same as above, painted* 250 2 1 SC16DP-26 For 7 mm RG6 cable with a 1" drive pin 250 2 1 SC16DPP-26 Same as above, painted* 250 2 1 SC16DP-3Q For 8 mm QUAD cable with a 1" drive pin 250 2 1 SC16DPP-3Q Same as above, painted* 250 2 1 SC16DP-411 For 10 mm RG11 cable with a 1" drive pin 250 2 1 SC16DPP-411 Same as above, painted* 250 2 1

*25 per polybagColors available specify: black, white, beige or grey.

www.tvcinc.com

Section 4: Hardware

Clips

(888)644-60754 - 33

“SAXXON”™ Cable Clip

“Galvalume” steel cable clip used on wood, stucco or mortar with a hardened Pre-Inserted Nail.

Ordering Information

“U” Cable Clip

Preformed aluminum cable clip used to secure drop cables and ground wires to either wood ormasonry surfaces using SC25 screws.

Ordering Information

Siding Clips

DIAMOND’s Siding Clips are designed to attach coaxial cable (RG 59/U, RG 6/U) to aluminum, vinyl or steel sidedcustomer premises.

• Made of high quality, weather-resistant, high density, outdoor polypropylene.• Contains inhibitors to retard ultraviolet degradation.• Contoured surfaces facilitate installation.• Available in black and white colors.

Ordering Information

Part Number Specifications

StdPkgQty

Apxwt/pkg(lbs)

Apxwt/pkg

(kg) SC18-19 For 6 mm RG59 cable 500 2.5 1.1 SCI18P-19 Same as above, painted* 500 2.5 1.1 SC18-26 For 7 mm RG6 cable 500 2.5 1.1 SC18P-26 Same as above, painted* 500 2.5 1.1 SC18-3Q For 8 mm QUAD cable 500 2.5 1.1 SC18P-3Q Same as above, painted* 500 2.5 1.1 SC18L-19 For 6 mm RG59 cable with 1.625" hardened nail 500 3 1.4 SC18LP-19 Same as above, painted* 500 3 1.4 SC18L-26 For 7 mm RG6 cable with 1.625" hardened nail 500 3 1.4 SC18LP-26 Same as above, painted* 500 3 1.4 SC18L-3Q For 8 mm QUAD cable with 1.625" hardened nail 500 3 1.4 SC18LP-3Q Same as above, painted* 500 3 1.4Colors available specify: black, white, beige or grey. *50 per polybag

Part Number Specifications

Std.Pkg.Qty.

Apx.Wt/pkg

(lbs)

Apx.Wt/pkg

(kg) SC19 For RG59 cable 500 1 0.5 SC20 For RG6 cable 500 1 0.5 SC21-1 For #12 or #14 AWG ground wire 500 1 0.5 SC21-2 For #10 or #6 AWG ground Wire 500 1 0.5 SC22 For RG11 cable 400 1 0.5

CatalogNumber Description Box

QtyCartQty

Weight Per1000 Pcs.

(lbs.)12-01501 TVCG-1 Horizontal/Black 100 1,000 2.212-01401 TVCG-1 Horizontal/White 100 1,000 2.212-01502 TVCG-2 Vertical/Black 100 1,000 5.212-01402 TVCG-2 Vertical/White 100 1,000 5.2

www.tvcinc.com

Section 4: Hardware

Clips

(888)644-60754 - 34

D-SC Clip

Fastened with ordinary pliers, the S shaped clip is used to secure the loop in the drop cable at the point of the dropwire clamp or porcelain knob attachment.

• Made of soft aluminum for easy forming.• Corrugated to provide a positive grip on the drop wire.• Clips are free of burrs and sharp edges.

Ordering Information

“S” Cable Clip

Cable clip used to prevent separation of two cables or a messenger steel wire from a drop cable

Ordering Information

One-Nail Straps for Coaxial Cable

• Hardened nails made from high carbon steel drive into plaster, mortar and concrete block.• The black color of these straps and the addition of a UV stabilizer provide maximum resistance to the

effects of sunlight.

Ordering Information

PartNum ber

M ax.Cable Size Specifications

23-80366 .160" x .300" 1-2 pr. “S” clip23-80261 .225" x .375" 2-3 pr. “S” clip23-80262 .300" x .500" 6 pr. “S” clip

Part Number Specifications

StdPkg.Qty.

Apx.Wt/pkg

(lbs)

Apx.Wt/pkg

(kg) SC10 Made of soft aluminum for easy finger forming 500 4 1.8

SC10T Made of corrugated aluminum to provide a positivegrip on telephone cable 500 4 1.8

CatalogNumber

MaxCable Size Color Box

Qty.Cart.Qty

Weight per Cart.

CC-1005 #12 Ground Wire (.140" Dia.) Black 100 1000 3 lbs.CC-1010 59/U (.242" Dia.) Black 100 1000 3 lbs.CC-1020 6/U (.275" Dia.) Black 100 1000 3 lbs.CC-1030 6U Quad Shield (.300" Dia.) Black 100 1000 4 lbs.CC-2010 59/U Dual (.250" x .500") Black 100 1000 5 lbs.CC-2020 6/U Dual (.305" x .594") Black 100 1000 5 lbs.

www.tvcinc.com

Section 4: Hardware

Clips

(888)644-60754 - 35

Nail Clips

Tyton Nail Clips are easy to use and highly reliable. The tough, precision engineered plastic clips hold wire and cablesecurely in place. The nail is hardened for driving into wood, masonry joints, cinder block and mortar. The nails are alsoperpendicular to the work surface and are driven straight in, greatly reducing cracking. The Nail Clips do not have sharpedges. This reduces the chance of cutting cable jackets or sheaths and causing signal loss.

Ordering Information

Masonry Clips

Masonry Clips are a low cost, easy method for mounting station wire and PBX cable to cinder block, masonry and other formsof concrete. They are made from high impact, flame retardant Lexan with two steel pins molded into them. The M63-3 isspecially designed with only one pin for routing near corners. Standard Color: clear.

Ordering Information

TVC Nylon Cable Clips

TVC Brand Nail Clips are easy to use and highly reliable. The unique clip-on design allows for fast and simple installation.The nail is hardened for driving into wood, masonry joints, cinder block and mortar. The nails are also perpendicular to thework surface and are driven straight in, greatly reducing cracking. The Nail Clipsdo not have sharp edges. This reduces the chance of cutting cable jackets orsheaths and causing signal loss.

Ordering Information

CatNo.

Clip RangeInches(mm)

NailLength Color Coaxial Cable

NC2* .08-.10 (2-2.5) 1" B&W 14 AWG Ground wireNC3.5* .14-.16 (3.5-4) 1" B&W 12 AWG Ground wireNC6* .24-.28 (6-7) 1" B&W RG59NC7* .28-.32 (7-8) 1" B&W RG6 and RG59 double NC8* .32-.35 (8-9) 1" B&W RG7 and RG6NC9* .35-.43 (9- 11) 1" B&W RG 7NC11* .43-.47 (11-12) 1" B&W RG 11FC14* 0.54 (13.8) 1" B&W Flat twin and ground

PartNo.

Unit ofMeasure

MaxCable Dia.

M63-1 in.mm

0.256.35

0.62515.88

0.256.35

0.1884.75

M63-2 in.mm

0.512.7

1.2531.75

0.512.7

0.512.7

M63-3 in.mm

0.512.7

0.87522.2

0.512.7

0.512.7

Dimensions

M63-1 M63-3

M63-2

NC-5 NC-7 NC-14

NC-2 NC-3.5

CatalogNo. Description Color Pkg

QtyTNC-7B RG-6 Black 1000TNC-7W RG-6 White 1000

www.tvcinc.com

Section 4: Hardware

Dead Ends & Splices

(888)644-60754 - 36

Guy-Grip® Dead-endsPreformed

Ordering Information

PREFORMED – False Dead-ends

PREFORMED False Dead-ends are a fast, safe, and economical method for false dead-ending strand. They areeasily applied without any special tools, and because False Dead-ends are made from the same material as thestrand, they will hold the same published rated breaking strength.

Ordering Information

Units Wt./lbs.

Size Const. MeanDia.

GDE-1102 3/16" 7W7W

.186"

.195" 20" Red 100 30 B Coated

GDE-1104 1/4"3W7W3W

.259"

.240"

.312"25" Yellow 50 24 B Coated

GDE-1104LA 1/4" 7W .240" 23" Yellow 100 36 A Coated

GDE-1106 5/16" 7W7W

.312"

.356" 31" Black 50 39 B Coated

GDE-1107 3/8" 3W7W

.356"

.360" 35" Orange 50 51 B Coated

GDE-1108 7/16" 7W .435" 38" Green 25 40 B Coated

GDE-2102 3/16" 7W7W

.186"

.195" 20" Red 100 30 C Coated

GDE-2104 1/4"3W7W3W

.259"

.240"

.312"25" Yellow 50 24 C Coated

GDE-2106 5/16" 7W7W

.312"

.327" 31" Black 50 39 C Coated

GDE-2107 3/8" 3W7W

.356"

.360" 35" Orange 50 51 C Coated

GDE-2108 7/16" 7W .435" 38" Green 25 40 C Coated

CoatingPer Carton

StrandPartNo. Length Color

Code

PartNo.

Strand7-Wire

Mean(dia) Length Color

Code Units Wt./lbs.Per Carton

GFDE-2121 1/4" .240" 36" Yellow 25 17GFDE-2123 5/16" .327" 39" Black 25 24GFDE-2124 3/8" .360" 42" Orange 25 30GFDE-2125 7/16" .435" 48" Green 25 52GFDE-2126 1/2" .495" 50" Blue 25 71

Galvanized Steel Strand C-Coat

www.tvcinc.com

Section 4: Hardware

Dead Ends & Splices

(888)644-60754 - 37

Dead-Ends (Galvanized Steel)

There is no quicker, easier way to support Figure-8 wire or cable than with PREFORMED dead-ends. Merely stripthe messenger and wrap on the dead-end for permanent installation. The helical shape will insure low distribution ofholding stresses to prevent premature fatigue. False or double dead-ending can be accomplished without cutting themessenger, a feature exclusive with all PREFORMED dead-ends.

Ordering Information

Description Cable CatalogDiameter Number

• For Use on Galvanized Steel Messenger .............. .051" ...................... DE-2525• For Use on Galvanized Steel Messenger .............. .063" - .072" .......... DE-2505• For Use on Galvanized Steel Messenger .............. .083" ...................... DE-2506• For Use on Galvanized Steel Messenger .............. .109" ...................... GDE-2501• For Use on Galvanized Steel Messenger .............. .134" ...................... GDE-2503

www.tvcinc.com

Section 4: Hardware

Dead Ends & Splices

(888)644-60754 - 38

PREFORMED – Strand Splices

PREFORMED Strand Splices are used to repair strand or messenger simply and economically. All applications can bechecked visually-no guesswork involved. Because of its superior design, the Strand Splice provides maximum strength andexcellent fatigue characteristics resulting in longer life for both strand and messenger.

Ordering Information

Strandvise & Strandlink

A mechanical holding device for wire, strand and rod that is used primarily by telephone and electric utilities to hold strand orrod for guying purposes to deadend at the pole top and at the ground. The strandlink is a splice and is used to make aconnection between two pieces of strand or rod, generally used when a guy is broken or when moving guys.

• Simple, fast and foolproof installation.• Cartridge made of a sturdy, corrosion resistant 6061-T6 Aluminum Alloy.• Jaws are cold forged 1010-1015 low carbon steel case hardened and zinc chromated.• The jaw washer is a 1010-1015 low carbon steel.• The spring is a hard drawn tinned steel.• Yoke is a 6061-T6 extruded aluminum.• The bails are a 300 series stainless steel with the lobes being cold headed.• Each strandlink fitting is sealed with a pilot cup on each end.• The strandvise uses one pilot cup and an end cap.• All strandvises are equipped with release slots.• A lubricant coats the internal portion of the tube and jaws.• A variety of bail configurations and sizes are available to handle virtually all requirements.

Ordering Information

Units Wt./lbs.

Size Constr. Mean(dia.)

GLS-2102 3/16" 7W .186" 27" 2 Red 100 30GLS-2104 1/4" 7W .240" 35" 2 Yellow 50 34GLS-1104* 1/4" 7W .240" 35" 2 Yellow 50 32GLS-2106 5/16" 7W .312" 42" 3 Black 50 46GLS-2107 3/8" 7W .360" 50" 3 Orange 25 38GLS-2108 7/16" 7W .435" 56" 3 Green 25 57GLS-2109 1/2" 7W .495" 63" 3 Blue 10 34

Extra High Strength Strand C-Coat

Per Carton

StrandPartNo. Length

No. of

Subsets

Color Code

Strandlink

For strain insulator

types 502, 504

X-long to placemultiple Guys onTriple Eye Rods

Wire Range(in)

(mm)

All grades incl. EHS, Bell Syst.

UltimateLoad

N/A R5099 N/A N/A .185" -. 193", 3/16"4.70 - 4.95 2.2M 4,200 lbs

1,905 kg.

R5000 R5100 R5150 R5100-L .240" - .253", 1/4"6.10 - 6.43 6.6 M 7,000 obs

3,175 kg.

R5001 R5101 N/A N/A .310" - .335", 5/16"7.87 - 8.51 6M 11,500 lbs

5,216 kg.

R5002 N/A N/A .360" - .405", 3/8"9.14 - 10.29 10M 15,500 lbs.

7,031

StandviseSpecifications

Short bails for eyes

and hooks

Long Bail Types

• Reducter Type Universal Strandlink..........R5087 (End A - 5/16”, .270, .315) (End B - 1/4” .215-.270)

www.tvcinc.com

Section 4: Hardware

Dead Ends & Splices

(888)644-60754 - 39

Wirevise & Wirelink

MacLean Power Systems’ Mechanical Holding Device for small gauge wire and strand is used for splicing and deadendingaluminum covered steel copper or copper covered steel or steel strand when used as a messenger for telephone or electricutility applications. Used wherever a holding device is required for terminating or splicing solid wire or strand.

Features• The wirelink and wirevise for use with steel and aluminum covered steel are made of heat treated aluminum tubing

with case-hardened plated steel jaws.• This wirevise has a stainless steel bail and an aluminum alloy yoke.• Wirelink and wirevise for use on copper covered steel wire are made of copper tubing and have bronze jaws.• The wirevise has a stainless steel bail and a bronze yoke.• Both types are lubricated with inhibitor lubricants and individually packaged in plastic containers.• The wirelink is available with a polyolefin coating for use in continuing the insulation when splicing insulated or

jacketed support wires.

Ordering Information

in. mm in. mm in. mm in. mm

*Polyolefin-covered wirelink +Universal strandlink and strandvise

R5056 6-1/2 165.12-15/16 75.6 .454 1 27.0R5057*R5057N

2-15/16 75.6 .479 12.2 R5058 6-13/16 173.0

11.5

9-13/32 238.9 6-31/32

5

103.2 .546 13.9 R5062

6-1/2 165.1

5 127.0

1.026 26.1

177.0

4-5/32 105.6 .575 14.6 R5072 9-1/4 235.0

R5199A 8-1/2 215.9 4-7/8 123.8

127.05165.16-1/2R507812.2.47975.62-15/16R5079

R5059*R5059N

R5063*R5063N

R5073*R5073N

R5039*R5039N+ 9 228.6

4-1/16

Inches .140 - .215 (mm 3.7 - 5.5)9 U.S.S.W.G. (.1483) 9 BWG (.148)8 U.S.S.W.G. (.1520) 8 BWG (.165)7 U.S.S.W.G. (.1770) 7 BWG (.180)6 U.S.S.W.G. (.1920) 6 BWG (.203)5 U.S.S.W.G. (.2070)

Inches .091 - .114 (mm 2.3 - 2.9)11 AWG (.091) 12 S.W.G. (.104)10 AWG (.102)9 AWG (.114)

Inches .062 - .100 (mm 1.4 - 2.6) 16 U.S.S.W.G. (.0625) 16 BWG (.065)15 U.S.S.W.G. (.0720) 15 BWG (.072)14 U.S.S.W.G. (.0800) 14 BWG (.083)13 U.S.S.W.G. (.0915) 13 BWG (.095)

Inches .091 - .114 (mm 2.3 - 2.9) 13 U.S.S.W.G. (.0915) 13 BWG (.095)12 U.S.S.W.G. (.1055) 12 BWG (.109)

Inches .120 - .135 (mm 3.1 - 3.5)11 U.S.S.W.G. (.1205) 11 BWG (.120)10 U.S.S.W.G. (.1350) 10 BWG (.134)(Except Gcl 90)2,500 lbs. Max.

Inches .120 - .135 (mm 3.1 - 3.5)11 U.S.S.W.G. (.1205) 11 BWG (.120)10 U.S.S.W.G. (.1350) 10 BWG (.134)

Wire Range

Wirelink Wireverse

A BPartNo.

PartNo.

A B

For steel wire and aluminum covered steel wire

www.tvcinc.com

Section 4: Hardware

Eyes

(888)644-60754 - 40

Auxiliary Eyes PA155

Designed to fulfill the need for an economical attachment of an additional guy to an existing anchor rod. Long inuse by many power and telephone companies. Where anchor capacity is available, Auxiliary Eyes offer the mosteconomical method of adding one or even two additional guys to any type of existing anchor rod. Can also be usedfor temporary guying or as a come-along to tension guys. Easy installation, generous thimble diameter.

• Malleable Iron, Hot Dip Galvanized Body & Plates• Hi-Strength Steel & Hot Dip Galvanized “U” Bolts & Nuts

Ordering Information

Eyelets

Designed to meet E.E.I. dimensional and strength specifications. Will exceed the rating of the bolt with which eachis used. Hole design permits thru bolt to be inserted from the eye side. More economical than a steel forging.

Ordering Information

Forged Eyenuts

Joslyn hot dipped galvanized Forged Eyenuts are tapped to fit hot dip galvanized bolts made to ANSI Specificationsand are designed to develop strength ratings consistent with the bolts with which they are used.Thimbleyenuts® are used for span, head and stub guying; Twineyenuts® accommodate double guys. Oval eyenutsare used for deadending with suspension or strain insulators.

Ordering Information

PartNo. Type Rod

Dia

Max.Strand Thimble

SizeDia. Material

PA155 Sq. 5/8-3/4" 1/2" 1-1/2" MalleablePA155H Hex 5/8-3/4" 1/2" 1-1/2" MalleablePA155A Sq. 7/8-1" 1/2" 1-1/2" MalleablePA155AH Hex 7/8-1" 1/2" 1-1/2" Malleable

PartNo. Type Bolt

Dia.Strand Max.

Shipping Wt.Per 100 Pieces

Std. Pkg.Qty.

P127A* Std. Long 5/8" 1/2" 96 lbs. 50P127B* Std. Long 3/4" 1/2" 99 lbs. 50P126B* Thimble 5/8" 1/2" 105 lbs. 50P126A* Thimble 3/4" 1/2" 151 lbs. 50*Equals or exceeds EEI requirments

Part No.

For BoltDia (in)

Max. StrandSize 9in)

Appro. Ship WT(lbs. per 100 pcs.)

J6510 5/8 1/2 91J6511* 3/4 1/2 91 Part

No.For BoltDia (in)

Max. StrandSize 9in)

Appro. Ship WT(lbs. per 100 pcs.)

J1092* (E) 5/8 — 54J1093 3/4 — 53*ANSI Standard (E) REA Accepted

Thimbleynuts

Oval Eyenuts

www.tvcinc.com

Section 4: Hardware

Grounding Materials

(888)644-60754 - 41

TVC Brand Ground Block and F-81 Splice

TVC has developed a line of true 1 GHz splice and ground block devices capable of providing high return losscharacteristics at frequencies over 1 GHz. The models G-F81L and G-G2B2 have been constructed usingtraditional high frequency design techniques coupled with the required physical durability of CATV products toprovide return losses over 25 dB at 1 GHz. The mechanical design techniquesprovide a minimum of 100% more cable center conductor-to-connecter contactarea resulting in higher reliability and transmission performance.

Ordering Information

Catalog No. MHz Std.

Pkg.Weight

Std. Pkg.G2B2 750 500 36 lbs.

G-G2B2 1000 500 36 lbs.F-81 750 100 1.06 lbs.

G-F81L 1000 100 1.60 lbs.

High Pass Filter, Ground Blocks

FeaturesThe ground block with built-in high pass filter prevents low frequencies from entering the system at the drop. Thisproduct should be used on all active two-way systems. In addition, the unit eliminates the need for multiplematching transformers with high pass filters. The GHP-50 features zinc diecast housing and is completely weatherproof. Each port is machine threaded for a perfect connector fit.

GRB-1 TVC BrandGrounding block with F81 zinc

GRB-2 TVC BrandDual grounding block with F81 zinc

GB-81 LRCGround blocks made from high-quality,extruded aluminum alloy are available foruse with environmentally sealed products(i.e. thread protectors). All suppliedscrews have #2 Phillips -1/4" HexCombination Head

Ground Blocks

GB-81 LRC

GRB-1

GRB-2

www.tvcinc.com

Section 4: Hardware

Grounding Materials

(888)644-60754 - 42

SC12DNS Grounding Block

Grounding block used for CATV subscriber grounding application. Unique Locking Tab designed to facilitate theinstallation of the F81 connector. New Oval Slot permits upgrading with various brands of 2, 3 or 4 way splitters,simply by using the SCO9 splitter ring nut for mounting. Quick insert-and-wrap locking hole to accept up to #10AWG ground wire. Made of G90 galvanized steel with a yellow-chromate overcoat. Supplied with stainless steelgreen grounding screw.

Ordering Information

SC12DNMS Grounding Block

Grounding block used for CATV subscriber grounding application. Unique Locking Tab designed to facilitate theinstallation of the F81 connector. New oval slot permits upgrading with various brands of 2, 3 or 4 way splitters,simply by using the SCO9 splitter ring nut for mounting. Quick insert and wrap locking hole to accept up to #10AWG ground wire. Made of G90 galvanized steel with a yellow-chromate overcoat. Supplied with stainless steelgreen grounding screw and a stainless steel screw to bond steel messenger wire.

Ordering Information

SC12DS Grounding Block

Grounding block used for CATV subscriber grounding application. Quick insert-and wrap locking hole to accept up to#10AWG ground wire. Made of G90 galvanized steel with a yellow-chromate overcoat. Supplied with stainless steelgreen grounding screw.

Ordering Information

Part Number Specifications

StdPkgQty

Apx.wt./pkg

(lbs)

Apx.wt./pkg

(kg)SC12DNS-81 Complete with regular F81 connector 100 10 4.5

SC12DNS-81 L Complete with long barrel F81 connector 100 11 5

SC12DNS81-25 As SC12DNS-81 with two SC25-3 mounting screws 100 12.5 5.7

SC12DNS81L-25 As SC12DNS-81 L with two SC25-3 mounting screws 100 13.5 6.1

SC12D and SC12DN series can also be available with two F81 type connectors to specify short or long barrel.

Part Number Specifications

StdPkgQty

Apx.wt./pkg

(lbs)

Apx.wt./pkg

(kg) SC12DNMS-81 Complete with regular F81 connector 100 11 5 SC12DNMS-81 L Complete with long barrel F81 connector 100 12 5.4 SC12DNMS81-25 As SC12DNMS-81 with two SC25-3 screws 100 13.5 6.1 SC12DNMS81L-25 As SC12DNMS-81 L with two SC25-3 screws 100 14.5 6.6SC12D and SC12DN series can also be available with two F81 type connectors to specify short or long barrel.

Part Number Specifications

StdPkgQty

Apx.wt./pkg

(lbs)

Apx.wt./pkg

(kg)SC12DS-81 Complete with regular F81 connector 100 10 4.5SC12DS-81L Complete with long barrel F81 connector 100 11 5SC12DS81-25 As SC12DS-81 with two SC25-3 mounting screws 100 12.5 5.7SC12DS81L-25 As SC12DS-81L with two SC25-3 mounting screws 100 13.5 6.1

www.tvcinc.com

Section 4: Hardware

Grounding Materials

(888)644-60754 - 43

SC12DMS Grounding Block

Grounding block used for CATV subscriber grounding application. Quick insert and wrap locking hole to accept up to#10AWG ground wire. Made of G90 galvanized steel with a yellow chromate overcoat. Supplied with stainless steelgreen grounding screw and a stainless steel screw to bond steel messenger wire.

Ordering Information

SC12N Grounding Block

Grounding block used for CATV subscriber grounding application. Unique locking tab designed to facilitate theinstallation of the F81 connector.

Ordering Information

SC12-4W Four Way Grounding Block

Four way grounding block used for CATV subscriber grounding application. Provides up to four drop connections witha #6 AWG ground connection.

Ordering Information

Part Number Specifications

StdPkgQty

Apx.wt./pkg

(lbs)

Apx.wt./pkg

(kg)SC12DMS-81 Complete with regular F81 connector 100 11 5SC12DMS-81L Complete with long barrel F81 connector 100 12 5.4SC12DMS81-25 As SC12DMS-81 with two SC25-3 mounting screws 100 13.5 6.1SC12DMS81L-25 As SC12DMS-81 L with two SC25-3 mounting screws 100 14.5 6.6SC12D and SC12DN series can also be available with two F81 type connectors to specify short or long barrel.

Part Number Specifications

StdPkgQty

Apx.wt./pkg

(lbs)

Apx.wt./pkg

(kg)SC12N-81 Complete with regular F81 connector 150 9 4.1SC12N-81L Complete with long barrel F81 connector 150 10 4.5SC12N81-25 As SC12N-81 with two SC25-3 mounting screws 150 12 5.4SC12N81L-25 As SC12N-81 L with two SC25-3 mounting screws 150 13 5.9SC12D and SC12DN series can also be available with two F81 type connectors to specify short or long barrel.

Part Number Specifications

StdPkgQty

Apx.wt./pkg

(lbs)

Apx.wt./pkg

(kg)SC12-4W Complete with four regular F81 connectors 50 13 .9SC124W-25 Same as above but with two mounting SC25-3 screws 50 15 6.8SC12-4WL Complete with four long barrel F81 connectors 50 17 7.7SC124WL-25 Same as above but with two SC25-3 mounting screws 50 18 8.2SC12D and SC12DN series can also be available with two F81 type connectors to specify short or long ba

www.tvcinc.com

Section 4: Hardware

Grounding Materials

(888)644-60754 - 44

SC12NED “ED” Grounding Block

“ED” grounding block used for CATV subscriber grounding application. Permits upgrading by replacing the initial F-81connectors with 2, 3 or 4 way splitters, limiting the use of only two F-81 connectors with up to a #10 AWG groundwire.

Ordering Information

SC23G Grounding Bracket

Grounding bracket provides a means to bond up to eight steel messenger wires to steel strand. Firm and positivegrip with no rotation or sliding on strand.

Ordering Information

SC46DN Grounding Bracket

Grounding bracket permits upgrading number of drops by mounting 2, 3 or 4 way splitters simply by using the SC09splitter ring nut for mounting.

Ordering Information

SC46DNM Grounding Bracket

Grounding bracket with a steel messenger wire connection permits upgrading number of dropsby mounting 2, 3 or 4 way splitters simply by using the SC09 splitter ring for mounting.

Ordering Information

Part Number Specifications

StdPkgQty

Apx.wt./pkg

(lbs)

Apx.wt./pkg

(kg)SC12NED-81 Complete with two F81 connectors 50 10 4.5SC12NED81-25 Same as above with two SC25-3 mounting screws 50 11 5SC12NED81L Complete with two F81 connectors long barrel 50 11 5SC12NED81L-25 Same as above with two SC25-3 mounting screws 50 12 5.4

Part Number Specifications

StdPkgQty

Apx.wt./pkg

(lbs)

Apx.wt./pkg

(kg)SC23G-2 For 2 steel messenger wires 100 28 12.7SC23G-4 For 4 steel messenger wires 50 14 6.4SC23G-8 For 8 steel messenger wires 32 11 5

Part Number Specifications

StdPkgQty

Apx.wt./pkg

(lbs)

Apx.wt./pkg

(kg)SC46DN Accepts up to #10 AWG ground wire 100 8 3.6SC46DN-25 Same as above with two SC25-3 mounting screws 100 10 4.5

Part Number Specifications

StdPkgQty

Apx.wt./pkg

(lbs)

Apx.wt./pkg

(kg)SC46ONM Accepts up to #10 AWG ground wire 100 9 4.1SC46ONM-25 Same as above with two SC25-3 mounting screws 100 1 1 6

www.tvcinc.com

Section 4: Hardware

Grounding Materials

(888)644-60754 - 45

SC46N-4W Four Way Grounding Bracket

Four way grounding bracket used for CATV subscriber grounding application. Accepts up to four F81 connectorswith a #6 AWG ground connection.

Ordering Information

SC46N-ED “ED” Grounding Bracket

“ED” ground bracket used for CATV subscriber grounding application. Accepts upgrading with 2, 3 or 4 waysplitters, limiting the use of only two F-81 connectors with up to a #10 AWG ground wire.

Ordering Information

SC03E-2G Span Clamp

Span clamp for single steel messengered drop cable bonding applications. Unique locking design prevents anypart rotation on steel strand.

Ordering Information

SC55 Universal Ground Clamp

Ground clamp used for connecting a copper ground wire to water pipe, ground rods and steelstrand to steel strand.

Ordering Information

Part Number Specifications

StdPkgQty

Apx.wt./pkg

(lbs)

Apx.wt./pkg

(kg)SC46N-4W Accepts up to #6 AWG ground wire 50 8 3.6SC46N-4W-25 Same as above with two SC25-3 mounting screws 50 9 4.1

Part Number Specifications

StdPkgQty

Apx.wt./pkg

(lbs)

Apx.wt./pkg

(kg)SC46N-ED Accepts up to #10 AWG ground wire 50 8 3.6SG46NED-25 Same as above with two SC25-3 mounting screws 50 9 4.1

Part Number Specifications

StdPkgQty

Apx.wt./pkg

(lbs)

Apx.wt./pkg

(kg)

SC03E-2G For single steel messenger wire .051" to .073"diameter used on 1/4" (6.6 mm) steel strand 75 14 6.4

SC03ET-2G Same as above used on 7/16" (16 mm.) steel strand 75 14 6.4

SC03E-3GW For bonding up to three steel messenger wires .051"to .073" diameter used for 1/4" (6.6 mm) steel strand 75 14 6.4

SC03ET-3GWI Same as above used on 7/16" (16 mm) steel strand 75 14 6.4

Part Number Specifications

StdPkgQty

Apx.wt./pkg

(lbs)

Apx.wt./pkg

(kg)

SC55Connects #6 AWG and #10 AWG to galvanized pipe1/2" to 1", ground rod up to 5/8" diameter, strand tostrand 1/4", 5/16", 7/16" and #2/0 AWG copper ground wire

50 28 12.7

www.tvcinc.com

Section 4: Hardware

Grounding Materials

(888)644-60754 - 46

SC07GG “I” Beam Grounding Clamp

Grounding clamp used to bond a solid or strand copper wire to steel structure.

Ordering information

SC23GE Span Ground Clamp

Span ground clamp used to dead-end at the tap and to bond messenger steel wires.

Ordering Information

“B” Ground Wire Clamp

The DIAMOND “B” Ground Wire Clamp is used in telephone and CATV drop installations to secure wire forgrounding.

Specifications• Made of high quality steel.• Mechanically galvanized to meet ASTM specifications A153 and B695.• Clamp dimensions are 9/16" long by 3/8" wide.• Clamp has a 1/8" curve to accommodate the wire to be grounded.• Hole diameter is 7/32".• R.E.A. accepted.• Manufactured in the USA.

Ordering Information

Part Number Specifications

StdPkgQty

Apx.wt./pkg

(lbs)

Apx.wt./pkg

(kg)SC07GG Up to #10 AWG copper ground wire 100 16 7.3SC07GG-142 Up to #6 AWG copper ground wire 100 19 8.6

Part Number Specifications

StdPkgQty

Apx.wt./pkg

(lbs)

Apx.wt./pkg

(kg)

SC23SE2 Common ground for two .051" to .073" messengersteel wires used for 1/4" (6.6 mm) steel strand 50 15 6.8

SC23GET2 Same as above used for 1/16" (16 mm) steel strand 50 15 6.8

SC23GE4 Common ground for four .051" to .079" messengersteel wires used for 1/4" (6.6 mm) steel strand 50 16 7.3

SC23GET4 Same as above used for 1/16" (16 mm) steel strand 50 16 7.3

CatalogNo.

Max. Wireor cable size

(in)

BoxQty

Cart.Qty

Weight Per100 Pcs.

(lbs)23-80002 1/8 500 5000 0.3

www.tvcinc.com

Section 4: Hardware

Grounding Materials

(888)644-60754 - 47

Meter Box Ground Clamp

Ordering Information

SC51 Bonding Connector for Meter Pan

Meter pan connector designed to provide a bonding connection between the metallic frame of a meter pan and acopper ground wire. Its unique design allows a fixed and positive mechanical contact without interfering with theopening of the meter pan front cover.

Ordering Information

L Ground Strap

DIAMOND’s L Ground Clamp is used to secure ground wires to power conduit, power mast or water pipes.

Specifications• Tin plated copper strap is suitable for mounting on any materials commonly used in grounding including

galvanized steel, copper water pipes, aluminum or die cast fittings.• Clamp range is between 1.800" and 3.580" diameters.• Small opening accepts No. 6 (.162" dia.) ground wire.• Secure smaller ground wires No. 14 (.064" dia.) thru No. 8

(.128" dia.) between first and second nut.• Conforms to Bell specifications.• Strap tensile strength is 33,000 psi min.• Bolt, washer and nuts are mechanically galvanized to ASTM B695 specifications.

Ordering Information

PartNo.

ClampRange Specifications

40-20000 7" - 10-1/4" Meter box ground clamp (S), #12-16 AGW40-20001 11-1/2" - 15-1/4" Meter box ground clamp (L), #12-16 AGW40-20002 11-1/2" - 15-1/4 Meter box ground clamp (S), #6 AGW40-20003 11-1/2" - 15-1/4" Meter box ground clamp (L), #6 AGW

Part Number Specifications

StdPkgQty

Apx.wt./pkg

(lbs)

Apx.wt./pkg

(lbs)SC51-1 For #10/12/14 AWG copper ground wire 100 9.5 4.3SC51-2 For #6 AWG copper ground wire 100 13 5.9SC51-1BE For #6 AWG meets Telco specs 100 26 12

Part Number

Hole Spacing

Clamp Range

Cart.Qty

Weight Per100Pcs (lbs)

29-09972 2.50" to 11.25" 1.800" to 3.580" dia. 100 16

www.tvcinc.com

Section 4: Hardware

Grounding Materials

(888)644-60754 - 48

Ground Strap

DIAMOND’S Ground Straps (available in copper and galvanized steel) are used for securing ground wires to waterpipes or conduits to provide a low resistance connection for grounding telephone and CATV service drops.DIAMOND’S Ground Straps are available in either 6", 9" or 12" lengths. Accommodates Solid Copper GroundWires from #48 to #8 AWG. The 6", 9" and 12" straps are designed to fit pipe or tubing having outside diametersranging from 5/8" through 1-3/4" and 5/8" through 3-1/2".

• Adjustable copper strap (per ASTM B152).• Adjustable galvanized steel strap (per ASTM A153).• One piece construction for easy installation• Weldless construction reduces possible breakage.• Brass nickel plated nut, screw and washer (per ASTM B134).• Slotted, hex head screw to accommodate a screwdriver, wrench or pliers.• Designed so the copper wire is in direct contact with the ground strap to assure a positive, low resistance

ground.• Underflap protects pipe from screw puncture.

Ordering Information

Ground Strap

Function: Connects ground wire to water pipe.

Ordering Information

SC13B Ground Strap

Ground strap used to provide a fixed and permanent connection between acopper water pipe to a copper ground wire.

Ordering Information

CatalogNumber

StrapLength

CartonQty

Weight Per100 Pcs.

(lbs.)Material

40-09806 6" 100 4 Copper40-09812 12" 100 6 Copper40-09807 6" 100 3.5 Galv. Steel40-09809 9" 100 4.4 Galv. Steel40-09813 12" 100 5.3 Galv. Steel

CatalogNo.

PipeSize (in)

WireSize

StdPkg

A-24-6 3/8 - 1" 14 150A-24-12 3/8 - 3" 10-6 150

Part Number Specifications

StdPkgQty

Apx.wt./pkg

(lbs)

Apx.wt./pkg

(lbs)

SC13B-1 6-1/2" strap, fits 1/2" to 1" dia. pipe to #10/12/14 AWGcopper ground wire 150 7 3.2

SC13B-2 9" strap, fits 1/2" to 2-1/4" dia. Pipe to #10/12/14 AWGcopper ground wire 200 12 5.4

SC13B-3 12" strap, fits 1/2" to 3" dia. pipe to #10/12/14 AWGcopper ground wire 150 10 4.5

Made of pure copper (ASTM B152-110). Brass fasteners (ASTM B16-360 and B134-260).

www.tvcinc.com

Section 4: Hardware

Grounding Materials

(888)644-60754 - 49

SC13BZ Galvanized Ground Strap

Ground strap used to provide a fixed and permanent connection between a galvanized water pipe or a servicemast to a copper ground wire.

Ordering Information

SC11TG “T” Grounding Strap

The new “T” grounding strap is designed to provide a fixed and permanent connection between a water pipe to acopper ground wire.

Ordering Information

SC42 Ground Connector

Ground connector used to connect various size copper ground conductors with a firm mechanical contact. Made ofpure copper (ASTM B152-110) with brass fasteners (ASTM B16-360 and B134-260).

Ordering Information

Part Number Specifications

StdPkgQty

Apx.wt./pkg

(lbs)

Apx.wt./pkg

(lbs)

SC13BZ-2 9" strap, fits 1/2" to 2-1/4" dia. pipe to #10/12/14 copper ground wire 200 12 5.4

SC13BZ-3 12" strap, fits 1/2" to 3" dia. pipe to #10/12/14 copper ground wire 150 10 4.5

Made of G90 galvanized steel that meets salt test ASTM B117.

Part Number Specifications

StdPkgQty

Apx.wt./pkg

(lbs)

Apx.wt./pkg

(lbs)

SC11TGC Copper strap to #6 AWG copper ground wireaccepts from 1/2" to 3" pipe 200 28 12.7

SC11TGS G90 galvanized steel to #6 AWG copper ground wireaccepts from 1/2" to 3" pipe 200 28 12.7

Made of G90 galvanized steel that meets salt test ASTM B117. Fasteners are made of brass, nickel plated (ASTM B16-360 and 6134-260).

Part Number Specifications

StdPkgQty

Apx.wt./pkg

(lbs)

Apx.wt./pkg

(lbs)SC42-4 Connects #4 AWG to #10 AWG copper ground wire 150 5 2.3SC42-6 Connects #6 AWG to #10 AWG copper ground wire 150 5 2.3SC42G-4 For use in conjunction with SC13B series 150 5 2.3SC42G-6 For use in conjunction with SC13B series 150 5 2.3SC42ZG-4 Nickel plated for use in conjunction with SC13BZ 150 5 2.3SC42ZG-6 Nickel plated for use in conjunction with SC13BZ 150 5 2.3Parts nickel plated for compatibility with aluminum cable sheath.

www.tvcinc.com

Section 4: Hardware

Grounding Materials

(888)644-60754 - 50

SC47-500 Feeder Grounding Connector

Grounding connector used to provide a bonding connection between a feeder cable anda copper ground wire. Made of pure copper (ASTM B152-110) with brass fasteners(ASTM B16-360 and B134-260).

Ordering Information

SC49 Ground Extension Bracket

Extension bracket used to provide a bonding connection between a tap and a copper ground wire in pedestal or lockbox.

Ordering Information

SC27 Messenger Grounder

Messenger grounder used in conjunction with various SACHS hard wire to bond a steel messenger wire.

Ordering Information

Ground Clamp

Ordering Information

Part Number Specifications

StdPkgQty

Apx.wt./pkg

(lbs)

Apx.wt./pkg

(lbs)SC47-500 For .500" feeder cable to a #6 AWG copper ground wire 100 6 2.7Parts nickel plated for compatibility with aluminum cable sheath.

Part Number Specifications

StdPkgQty

Apx.wt./pkg

(lbs)

Apx.wt./pkg

(lbs)SC49-1 Various tap brand to a #6 AWG copper ground wire 75 13 5.9SC49-2 JERROLD tap to a #6 AWG copper ground wire 75 13 5.9

Part Number Specifications

StdPkgQty

Apx.wt./pkg

(lbs)

Apx.wt./pkg

(lbs)

SC27 Accepts .051" to .073" steel messenger wire suppliedwith a stainless steel green screw 100 1.8 0.8

Catalog No. Size Material Cart.

Qty.Std. Pkg. Wt

GC-1 1/2" x 1" Bronze 25 250 52GC-2 1-1/4" x 2" Bronze 25 250 11GC-5 1/2" x 1" Die-Cast Zinc 25 250 44

www.tvcinc.com

Section 4: Hardware

Grounding Materials

(888)644-60754 - 51

Solid Copper Wire

Made to the specifications of theAmerican Society for Testing Materials.

Type TW Grounding Wire

Solid Copper Conductor - 600 Volts

Grounding Connectors

Fargo bronze vise type connectors are one piece, side loading, for easyinstallation on unbroken run conductors. The vise like construction provideinterlocking components for a vibration proof connection.The GC5006SH is used forgeneral purpose applications while the GC167P is used for Figure-8 or IM Cable.

Ordering Information

Catalog No. Dia. Std.

Pkg. Weight

GC167PMAR 1" 250 22.00GC5006SHMAR 3/4" 500 8.00

Ground Clamps Ground Rods

Part No.

Rod Dia.

Std. Pkg. Manufacturer

WB38 3/8" 100 Thomas & BettsWB12 1/2" 100 Thomas & BettsWB58* 5/8" 100 Thomas & BettsMARG5 5/8" 100 Marathon*UL Listed

Ordering Information

Part No. Description

A21-4 3/8" x 4' ground rod w/clampTV38 3/8" x 4' ground rod w/clampW125 1/2" x 5' ground rodW588 5/8" x 8' ground rod UL Listed

Ordering Information

Part No. Size(AWG) Dia. (in) Wt. 1000' Size (ft)4AWG 4 .20 123 2506AWG 6 .162 79 3158AWG 8 .13 49 5006 Solid-J 6 .220 100 50010TW 10 .23 40 50012TW 12 .15 27 50014TW 14 .13 18 50010THHN 10 .16 39 50012THHN 12 .13 25 50014THHN 14 .11 17 500

Size (AWG) Color Insul. Thickness64ths O.D. Net Wt.

lbs./mft. Cart. Size

14TW-B Black 2 .13" 18 500 ft14TW-W White 2 .13" 18 500 ft14TW-G Green 2 .13" 18 500 ft12TW-B Black 2 .15" 27 500 ft12TW-W White 2 .15" 27 500 ft12TW-G Green 2 .15" 27 500 ft10TW-B Black 2 .17" 40 500 ft10TW-W White 2 .17" 40 500 ft10TW-G Green 2 .17" 40 500 ft

www.tvcinc.com

Section 4: Hardware

Guy Hardware

(888)644-60754 - 52

Guy AttachmentsHot Dip Galvanized

Joslyn Guy Attachments provide an economical and efficient means of fastening guys to poles. Well rounded wiregrooves protect the strand from damage.

The formed steel style guy attachments feature a closed strand loop when mounted. The J6505 two-bolt type ismounted with a 3/4" through-bolt and a 1/2" lag screw to give additional strength and keep the attachment in line.

The ears of the malleable guy attachments will accommodate any type of guy loop or clamp bail. The lowermounting hole is for a 1/2" lag screw.

Wherever possible, installation should be made under the head of a machine bolt; when used under the nut, thethreaded portion of the bolt is subjected to stress, thus reducing strength.

Ordering Information

Guy Wire Serving Sleeves

Designed to secure and prevent flaring of loose end of strand projecting beyond guy clamp. Hot dip galvanized.

Ordering Information

HooksHot Dip Galvanized

Joslyn produces a complete line of hooks for supporting bailtype drop wire and deadend clamps from poles andcrossarms. The J3316P and J3318 drive hooks have rolled fetter drive threads and a pilot point for easy starting.

Ordering Information

PartNo.

Steel Size(in)

HoleDia. (in)

Approx.Shipping Wt.

(lbs. per 100 pcs.)J25164 (E) 2 x 3/16 11/16 113J6506 2 x 1/4 13/16 156

One-Bolt Formed Steel Type

(E) REA Accepted

Part No. Strand SizeJ5600 1/4"J5601 5-16"J5602 3/8"

PartNo.

Size(in)

ApproxShip Wt.

(lbs per 100 pcs.)J3316P 7/16 x 4-3/4 FD. 27.0J3318 5/16 x 3-1/2 FD. 11.6

www.tvcinc.com

Section 4: Hardware

Guy Hardware

(888)644-60754 - 53

Sidewalk Guy FittingsHot Dip Galvanized

These cast iron fittings are used with standard pipe near sidewalks and buildings where there is insufficient spacefor standard guying and where head clearance must be maintained.

• The J1501 pole plate is mounted with one 5/8" bolt and two 1/2" lag screws. • The J1502 end fitting clamps the strand. • The J0521 pole plate has four 9/16" holes for mounting with lag screws. • The J0522 end fitting requires a J931 guy clamp which must be ordered separately. • The 5/8 x 2-1/4" track bolt replaces one of the guy clamp bolts.

Ordering Information

Ram Head Guy Hook

Ordering Information

Hooks, Guy

Two J1019 guy hooks are normally mounted on opposite sides of a pole under two turns of guystrand to prevent the strand from slipping on the pole. The rounded side of the 1-3/4" x 3/8" halfoval steel prevents damage to the guy strand and its galvanized coating.

Ordering Information• J1019*(E) (Approx. Ship. Wt. per 100 pcs. - 80) *ANSI Standard (E) REA Accepted

Part No. Description Pipe

Size (in)

Approx.Ship Wt.

(lbs per 100 pcs.)J1501GEN (E) Pole Plate 2 380J1502 (E) Clamp End Fitting 2 521J0521+ Pole Plate 2 & 2-1/2 495J0522+ Clamp Bolt End Fitting 2 & 2-1/2 350(E) REA Accepted

Part No. Fig. A B

CMounting

Bolt

Thim.Dia Material

P133AX 3 3-15/16 1/2 3/4 1-3/8 MalleableP135AX* 4 3-1/8 7/8 5/8 1-3/8 MalleableP151X* 1 2-7/8 1/2 7/8 1-1/4 Malleable

Dimensions (in.)

Material Specifications: Malleable Iron ASTM A-197-47 / Hot-Dipped Galvanized ASTM A-153 *REA accepted

www.tvcinc.com

Section 4: Hardware

Guy Markers

(888)644-60754 - 54

Steel Cable GuardHot Dip Galvanized

Cable Guards are used to protect power and telephone cable at riser installations. They offer maximum protectionto cable against collisions and vandalism.Cable Guards are available either in inexpensive strap-mounted style or in one-piece type with integral mountingholes for ease of installation. Lag screws are used to secure to the pole.Guards without frustum can be used as extensions to attain any desired height on the pole. A carriage boltassembly is furnished on most styles to fasten extensions and to serve as a ground lead attachment.

Ordering Information

Plastic Cable Guard

Joslyn plastic U cable guards offer a strong, lightweight, maintenance-free means of cable protection. The non-conducting plastic guards are designed to nest over Joslyn one-piece galvanized guards as required by manyconstruction standards which calls for galvanized guard at the base and a plastic guard up the balance of the pole.The plastic guard may be cut to length in the field.

Ordering Information

PartNo.

SteelGauge B.W.

Length (ft)

Depth (in)

Width (in)

Rqd.Mounting

Straps

Approx.Ship Wt.

(lbs. Per 100 pcs)J985 14 5 1-1/8 1-1/8 J995 470J984 14 8 1-1/8 1-1/8 J995 700J986 14 5 2-3/16 2-3/16 J996 840J987 14 8 2-3/16 2-3/16 J996 1,340J989 14 8 3-3/16 3-3/16 J997 2,000

Strap Mounted Guards

PartNo.

SteelSize(in)

For GuardWidth

(in)

Mounting Hole Dia.

(in)

Approx.Ship Wt.

(lbs. Per 100 pcs)J995 1/8 x 3/4 1-1/8 9/32 19.1J994 1/8 x 3/4 1-1/4 9/32 20.4J996 1/8 x 3/4 2-3/16 9/32 31.0J997 3/16 x 1 3-3/16 11/32 69.3

Straps

Part No. Dimensions Weight Ea. (lbs.)PGU-210 2" x 10' 6.0

www.tvcinc.com

Section 4: Hardware

Guy Markers

(888)644-60754 - 55

Guy Markers

PREFORMED™ Guy Markers can be used where anchor guys are exposed to pedestrian or vehicular traffic.

Guy Markers offer several advantages: the O.D. of applied dead-ends is not a factor in product selection; widecombination of strands (range 3/16" -1/2") can be accommodated by one size Guy Marker; and it can be installedquickly without bolts or metal parts. The guy can be covered all the way around.

Made from a high impact polyvinylchloride plastic, Guy Markers retain good physical characteristics, within a rangeof extreme temperatures that are self-extinguishing when exposed to fire.

PREFORMED Reflective Plastic Guy Markers offer all the exclusive features of Guy Markers, plus the addition of atreated area which projects a bright reflection of any light that touches its surface.

Ordering Information

Plastic Guy MarkersTwo-Thirds Round Marker

The 2-1/2" diameter, two-thirds round design provides excellent visibility and permits installation over anchor rods upto 1-1/4" diameter. The markers are produced from high impact resistant PVC with ultraviolet stabilizers added forretention of color under U.V. conditions. Four sets of holes are located along the guard to permit flexibility ofmounting positions. Two different attachment methods are available-bolted clamp assemblies or wire ties. The boltedclamp markers are supplied with three galvanized clamp assemblies which enable tamper resistant attachment toguy wire diameters 3/16" through 1/2" and to anchor rods up to 1-1/4" diameter. The wire tie markers are suppliedwith three wire ties for a fast, low cost method of marker attachment.

Ordering Information

Part No. Description Attachment

MethodWeight Each

(lbs.)J1490G 7' Grey 3 Bolted Clamps 2.5J1490Y 7' Yellow 3 Bolted Clamps 2.5J1491G 8' Grey 3 Bolted Clamps 2.7J1491Y 8' Yellow 3 Bolted Clamps 2.7J1497G 7' Grey 3 Wire Ties 1.7J1497Y 7' Yellow 3 Wire Ties 1.7J1498G 8' Grey 3 Wire Ties 1.9J1498Y 8' Yellow 3 Wire Ties 1.9

PartNo.

LengthCode Color Units

Per Ctn. Wt./lbs.

RPG-5616 6' Yellow 25 27RPG-5617 7' Yellow 25 30RPG-5618 8' Yellow 25 35

Reflective (1,2)

(1) Special yellow tape is added which will reflect headlights approaching from front, back or side(2) Otherwise, the Guy Marker has the same design as standard

PartNo.

LengthCode Color Units

Per Ctn. Wt./lbs.

PG-5516 6' Yellow 25 27PG-5517 7' Yellow 25 30PG-5518 8' Yellow 25 35

Standard

www.tvcinc.com

Section 4: Hardware

Lashers

(888)644-60754 - 56

J2 Cable Lasher

The J2 Cable Lasher is used to lash an aerial cable or numerous cables to supporting strand or to an existinglashed cable with stainless steel lashing wire. The J2 Lasher’s design also gives it maximum service life. Thebody is cylindrical to help it slip more easily through branches and obstructions. There is a built-in mechanicalbrake to prevent unintended reversal, an automatic drum lock for easy span transfers, an all-range tensioningdevice for optimum strand traction and high strength front and rear gates for tighter lashing.

Features• Will lash any single or multiple aerial cables up to 3" (76 mm) diameter

across on any suspension strand from 1/4" (6 mm) to 7/16" (11 mm). Afactory modification will allow the lasher to accommodate 1/2" (13 mm)strand if necessary.

• Consists of a rotating drum supported on a carriage that provides themounting for a driving mechanism, cable lifters, cable and strandrollers.

• Each of two recessed magazines will hold a 1200' coil of .045" (365 mof 1.1 mm wire) lashing wire (or 450' of .065".). The lashing Wire is fullyrecessed and covered by a gate.

• Features a fast setup procedure, quick coil loading, and automaticdrum lock for easy span transfers and smooth forward travel.

• J2 Lashers make overlashing easy. Just push down on the strand rollerknob, rotate it a quarter turn and you can lash additional cables togetheron previously lashed cable.

• Positive internal gear to gear mechanism has no chains or belts to stretch, slip or break.• Constructed with heat-treated, plated steel, stainless steel, brass and aluminum components. Contains

sealed and oil-less bearings to minimize maintenance and assure durability.• Pre-drilled and tapped at the factory for mounting of the lasher guard or “halo”. For use when lashing on

overgrown areas.• The lasher is furnished with a rugged lightweight storage chest with corrosion resistant hardware,

recessed latches and a moisture-proof, tongue-in-groove for maximum protection when not in use.• Supplied with a 6' bridle rope assembly and snap hooks, and an information and operation manual.

Ordering Information

Part No. Description Wire Dia. Weight

86070 J2 Cable LasherStandard w/ chest .045 65 Ibs.(30 kgs)

J2 Cable Lasher w/ ChestModified fro 450" of .065" wire 65 Ibs.(30 kgs)

Weight of lasher only 46 lbs.(22 kgs)03165 3 lbs.(1.5 kg)08189 19 lbs.(8.9 kgs)

86071 .065

Bridle Rope Assembly onlyChest only

www.tvcinc.com

Section 4: Hardware

Lashers

(888)644-60754 - 57

C Cable Lasher

The C Cable Lasher is used to lash small diameter aerial cables to supporting strand with stainless steel lashingwire. It is used primarily for new installations.

Features• Will lash any single or multiple cables up to 1 5/8" (40 mm) dia. onto

bare 1/4" to 3/8" strand.• All the same high quality features as the J2 Cable Lasher; those

features include dual magazines allowing you to load two 1200' coils of.045" lashing wire, (365 m of 1.1 mm wire), the ability to mount a lasherguard of “halo” into pre-drilled holed, and a built in brake to preventbackroll.

• This unit is built to last; the parts are all made from plated steel, stainless steel,brass or aluminum. Contains sealed and self-lubricating bearings to maximizemaintenance and assure durability.

• The Lasher is furnished with a 6' bridle rope assembly and snap hooks, an information and operationmanual and a rugged lightweight storage chest.

Ordering Information

Part No. Description Wire Dia. Weight

71420 C Cable LasherStandard w/ chest .045 49 Ibs.(23 kgs)

C Cable Lasher w/ Chest Modified for 450' of .065" wire 49 Ibs.(23 kgs)

Weight of lasher only 33 lbs.(15.4 kgs)03165 3 lbs.(1.5 kg)07143 16 lbs.(7.5 kgs)

.06571421

Bridle Rope Assembly onlyChest only

www.tvcinc.com

Section 4: Hardware

Lashing Wire / Strand

(888)644-60754 - 58

Stainless Steel Lashing Wire

Strength - For equivalent sizes of lashing wire, Grade 430 stainless has a lower strength (breaking load) than eitherthe 302 or 316 Grades. If increased strength is required, either a larger diameterGrade 430 wire should be used or Grades 302 or 316 should be used becauseof their higher breaking strength. In extreme strength applications, doublelashings of Grades 302 or 316 should be considered for highest possibleload bearing capabilities.Corrosion - In order of increasing corrosion resistance, the materials areranked 430, 302, and 316. For general service conditions where thematerial is exposed to non-salt environments, Grade 430 is adequate.Where acid rain, heavy industrial pollution, and/or salt environments areencountered, Grade 316 should be used. Grade 302 has corrosion resistancewhich falls between the 430 and 316 and is suitable for mildly corrosive environments.

Ordering Information

Part No.

Wire Dia. Grade Description Tensile

Strength

Approx.Break Load

(lbs)

Std.Pkg.

CoilLength

045430 LG .045 430 Zapp Stainless Steel Lashing Wire 70-95,000 psi 111-151 6 1200'045302 LG .045 302 Zapp Stainless Steel Lashing Wire 80-120,000 psi 127-191 6 1200'045316 LG .045 316 Zapp Stainless Steel Lashing Wire 80-120,000 psi 127-191 6 1200'038302 LG .038 302 Zapp Stainless Steel Lashing Wire 80-120,000 psi 91-136 6 1600'MAR045430 .045 430 Marathon Stainless Steel Lashing Wire 70-95,000 psi 111-151 6 1200'MAR045302 .045 302 Marathon Stainless Steel Lashing Wire 80-120,000 psi 127-191 6 1200'MAR045316 .045 316 Marathon Stainless Steel Lashing Wire 80-120,000 psi 127-191 6 1200'MAR038302 .038 302 Marathon Stainless Steel Lashing Wire 80-120,000 psi 91-136 6 1600'

Used to attach cable to strand.

Strand WireGuy And Messenger Strand

Galvanized Steel Strand• Finish coatings: Class A, B, or C galvanized• Applications Include: Messenger Wrie, Overhead Ground or Static Wire, Guy Wire

Ordering Information

Also available in Bezinal Corrosive coating of 5% aluminum and 95% zinc. (Contact your TVC Representative for details)

Part No. Description Manufacturer Reel LengthEHS1/4US 1/4" EHS Strand Domestic 5000'EHS1/4IMP 1/4" EHS Strand Imported 5000'EHS1/4IMP-2500 1/4" EHS Strand Imported 2500'EHS1/4US-2500 1/4" EHS Strand Domestic 2500'EHS 3/8 3/8" EHS Strand Domestic 5000'EHS 5/16 5/16" EHS Strand Domestic 5000'EHS 7/16 7/16" EHS Strand Domestic 5000'

www.tvcinc.com

Section 4: Hardware

Molding

(888)644-60754 - 59

Ground Wire MoldingRigid Plastic (Polyvinyl Chloride) Black

Ordering Information

Wood Molding

Ordering Information

Part No. SizeA

SizeB

Feet perBundle

pcs. PerBundle

Weight perBundle

1109 1/2 1/2 1000 125 521115 3/8 3/8 1000 125 321116 3/4 3/4 600 75 681118 1 1 504 63 661119 1-1/2 1-1/2 200 25 391120 2 2 200 25 64

Part No. Description Std. Pkg. Weight/Std. Pkg.

1/2X8WM 1/2" x 8'Wood Molding 200’ 33

www.tvcinc.com

Section 4: Hardware

Pole Steps

(888)644-60754 - 60

Pole StepsHot Dip Galvanized

Joslyn Pole Steps have rolled fetter drive threads and a wide, flat driving surface make installation fast and easy. A

knurled ring indicates the proper driving depth.

Ordering Information Part No. Size (in) Approx. Ship Wt. (lbs per 100 pcs)

• J1118 ......................................5/8 x 10 ................................... 98

Detachable Pole StepsHot Dip Galvanized

detachable Pole Steps are used to prevent unauthorized climbing to the point on a pole where permanent stepsare installed. A special 9/16" x 4" fetter drive lag screw permanently attaches themounting plate to the pole. Twisting is prevented by a punched projection. A nail hole isalso provided. The detachable steps can be hung from the lineman’s belt. Whenattached to the pole, they extend 5-1/2". Steps are turned up at the outside edge to givelinemen a steady foothold.

Ordering Information Part No. Size (in) Approx. Ship Wt. (lbs per 100 pcs)

• J6235 ......................................Pole Plate / Lag Screw .......................... 64• J6236 ......................................Step ........................................................ 59

www.tvcinc.com

Section 4: Hardware

Screws

(888)644-60754 - 61

Lag ScrewsHot Dip Galvanized

Gimlet Point lag screws are installed with a wrench. Fetter Drive and Twist Drive Lag Screws can either bewrenched or driven like a nail for speedier installation without sacrificing any of the holding strength of regulargimlet point lag threads. Twist Drive Lags are furnished with a drive point for additional starting ease and accuracy.This feature is also available on most sizes of Fetter Drive lags.

All Joslyn lag screws have rolled threads. Below the head is an upsetshoulder with the same outside diameter as the threads to provide a snugfit in hardware mounting holes.

Ordering Information

Washer Head Lag StudsHot Dip Galvanized

Washer Head Lag Studs are used for light-duty mounting of cable hangers. The stud end is manufactured with aforged square washer head and a roll threaded stud with assembled square nut. The lag end has sharp rolledgimlet threads and a cone point.

Ordering Information

Gimlet Point

Fetter DriveReg. Point

Fetter DriveDrive Point

Twist DriveDrive Point

Gimlet DriveDrive Point

J8721–1/2 1/4 x 1–1 12 1–1/4 2.2J8722* J8652 1/4 x 2 1–1/2 2.9J8722–1/2’ J8652–1/2* 1/4 x 2–1/2 1–3/4 3.5J8723* 1/4 x 3 2 4.1J8732 J8732HH 5/16 x 2 1–1/2 4.7J8732–1/2 J8732–1/2HH 5/16 x 2–1/2 1–5/8 5.9J8733*J8733–1/2 J8733–1/2HH 5/16 x 3–1/2 2–1/2 8.2

J8742–1/2* 3/8 x 2–1/2 1–3/4 8.5J8773 J8743* J8743P* J8773HH 3/8 x 3 2 9.9

J8744 J8744P J8774HH 3/8 x 4 2–1/2 12.8J8753 J8753P J8753TP 1/2 x 3 2–1/4 19.6

J8784 J8754* J8754P* J8754TP 1/2 x 4 (E) 2–5/8 24.0J8754–1/2* J8754–1/2P* 1/2 x 4–1/2 2–5/8 26.2J8755 J8755P 1/2 x 5 (E) 3 28.0J8765 5/8 x 5 (E) 3–1/2 44.2

*NEMA Standard (E) REA Accepted

Part NumberSize(in)

Min Thread

Length (in)

Approx.Shipping Wt

(lbs per 100 pcs)

PartNo. Lag Size Stud Size

(in)

Approx.Shipping Weight(lbs per 100 pcs)

J9754 9/16 x 4 1/2 x 1-3/8 45J26315 11/16 x 5-1/2 5/8 x 1-1/2 114

www.tvcinc.com

Section 4: Hardware

Screws

(888)644-60754 - 62

Ordering Information

Catalog No. Size Length Type Std.

Pkg6X1/2 PHS 6 0.5" Pan Head Slotted 1006X3/4 PHP 6 0.75" Pan Head Phillips 1006X3/4 HWH 6 0.75" Hex Washer Head 1006X1 HWH 6 1" Hex Washer Head 1006X1 HHP 6 1" Hex Head Phillips 1006X1 PHP 6 1" Pan Head Phillips 1006X1 PHS 6 1" Pan Head Slotted 100

8X1/2 PHS 8 0.5" Pan Head Slotted 1008X3/4 HWH 8 0.75" Hex Washer Head 1008X3/4 HWHS 8 0.75" Hex Washer Head Slotted 1008X3/4 PHS 8 0.75" Pan Head Slotted 1008X1 HWH 8 1" Hex Washer Head 1008X1-1/4 HWH 8 1.25" Hex Washer Head 1008X1-1/2 HWH 8 1.5" Hex Washer Head 100

10X1 PHP 10 1" Pan Head Phillips 10010X1 PHS 10 1" Pan Head Slotted 10010X1 HWH 10 1" Hex Washer Head 10010X1-1/2 PHP 10 1.5" Pan Head Phillips 10010X1-1/2 PHS 10 1.5" Pan Head Slotted 100

14X1 HWH 14 1" Hex Washer Head 10014X1-1/2 HWH 14 1.5" Hex Washer Head 100

www.tvcinc.com

Section 4: Hardware

Spacers

(888)644-60754 - 63

Cable Spacers

The Plastic Cable Spacers are used in lashed cable construction to provide a separation between aerial cable andmessenger when necessary. Used with Lashed Cable Supports, the upper surface of the spacers bears againstthe messenger while the lower surface rests on the aerial cable.

Specifications• Made of quality, weather resistant, high density outdoor Polyethylene.• Contains inhibitor to retard ultra violet degradation

Ordering Information

Spacer TiesAerial Support Spacer Ties

Aerial Support Spacer Ties are molded from special high impact nylon and the spacers in a high density outdoorblack polypropylene to resist the harsh effects of sunlight, saltwater and harsh chemical environments. The one-piece ties are pre-grouped in handy multiples of 5 to save installation time.

Part No. Size (In.) Std. Pkg. Qty./CtnP-14 1/4" 50 500P-12 1/2" 50 500P-34 3/4" 25 250P-10 1" 25 250P-15 1-1/2" 25 250P-20 2" 25 250

Kinsel Type

Part No.

Minimum TensileUnlocking Strength

Approx.Length

Approx.Width

Approx.Max. Dia.

TAS100R 100 lbs. 7.50" .50" 1.75"TAS100M 100 lbs. 10.00" .50" 2.75"TAS100L 100 lbs. 16.00" .50" 4.50"

Place the spacer betweenthe cable and strand.Wrap the tie strap aroundthe cable and through thebackside loop.

Pull the spacer snug to thecable and wrap the tie straparound the strand. Passthe tie strap through thelocking buckle.

Electrician pliers may beused to snug* theinstallation and snip the tail.

* As the cable and strand expand atdifferent rates, the installationshould not be tight but just snug.

Tyton Aerial Support SpacerTies may be released byinserting a screwdriver underthe locking ratchet of thebuckle.

www.tvcinc.com

Section 4: Hardware

Staples

(888)644-60754 - 64

Finish Dimensions (in)(L x Inside Width x Wire Dai.)

Approx Wt.(lbs per 100 pcs)

J127 * Hot Dip Galvanized 2 x 1-1/16 x 3/16 3.3J128 * Hot Dip Galvanized 3 x 1-1/16 x 1/4 7.9J142 Hot Dip Galvanized 3 x 1-1/2 x 1/4 8.3J156 * Hot Dip GaIvanized 2 x 1/2 x .162 2.5J172 * Hot Dip Galvanized 1-1/2 x 3/8 x .148 1.5J173 * Hot Dip Galvanized 1-3/4 x 3/8 x .148 1.6J7487HDG * Hot Dip Galvanized 2 x 5/8 x .162 2.3J7493HDG * Hot Dip Galvanized 3 x 1-1/16 x 1/4 5.7J6490 * Coppercoated 2 x 5/8 x .162 3.6J6491 Coppercoated 2-1/2 x 1 x 1/4 6.5J6492 * Coppercoated 1 x 1/4 x .114 .5J6493 * Coppercoated 1-1/4 x 5/16 x .114 .6J6494 * Coppercoated 1-1/2 x 5/16 x .144 1.2J6495 * Coppercoated 1-3/4 x 3/8 x .144 1.5J6496 * Coppercoated 2 x 1/2 x .162 2.2J6497 *(E) Coppercoated 3 x 1-1/16 x 1/4 8.0J6498 * Coppercoated 2-1/2 x 1-1 /1 6 x 3/16 3.9J6499 Coppercoated 3-1/2 x 1-1/2 x 1/4 9.8J6521 Coppercoated 2 x 1-1/16 x 3/16 3.1J6522 * Coppercoated 3 x 1 x 1/4 7.9J6523 Coppercoated 3 x 3/4 x 1/4 7.7J6524-C Coppercoated 3 x 1-1/2 x 1/4 8.3J7482 * Electro-Galvanized 1-1/2 x 1/4 x .120 1.2J7483 Electro-Galvanized 1-1/2 x 3/8 x .148 1.4J7484 Electro-Galvanized 1-3/4 x 3/8 x .148 1.5J7486 * Electro-Galvanized 2 x 1/2 x .162 2.2J7487 * Electro-Galvanized 2 x 5/8 x .162 2.3J7488 Electro-Galvanized 2 x 5/8 x 3/16 3.2J7490 Electro-Galvanized 2-1/4 x 25/32 x 3/16 3.6J7491 Electro-Galvanized 2-1/2 x 29/32 x 3/16 3.7J7492 * Electro-Galvanized 3 x 3/4 x 1/4 7.0J7493 * Electro-Galvanized 3 x 1-1/16 x 1/4 7.5J7487AL * Aluminum Clad 2 x 5/8 x .187 2.6J7493AL *(E) Aluminum Clad 3 x 1-1/16 x 1/4 6.6

PartNo.

(E) REA Accepted *ANSI Standard

Coppercoated, hot dip galvanized, electro-galvanized, mill galvanized and aluminum clad staples are used tosecure ground wire and ground wire molding to wood poles.

Ordering Information

Rolled (Diamond) Point

www.tvcinc.com

Section 4: Hardware

Tree Guards

(888)644-60754 - 65

PREFORMED Tree Guards are designed to protect bare conductors and fabric-covered or plastic-covered cables against mechanical abrasion caused by tree limbs orother obstructions. Tree Guards provide fast, easy application without disconnectingthe wire. Helical strips are matched, then wrapped over and around the wire, and tapedat each end. High-impact polyvinyl chloride has a strong abrasion resistance, strongweathering endurance, and high dielectric properties.

Ordering Information

Split Tube Cable Protector

Features• Semi-rigid U.V. stabilized exterior poly tube• Wraps around and protects cable

ColorsStandard color is black

Ordering InformationPart No. Size

• 3423TG...................................1/2" x 6'• 3433TG...................................1" x 6'• 3435TG...................................1-1/2" x 6'• 3437TG...................................2" x 6'

PartNo. Dia. Min. Range

Max. Length WallThickness Units Wt./lbs

Per Ctn.

PTG-0125 .479" .511" 6' 1/16" 75 32PTG-0128 .512" .542" 6' 1/16" 75 32PTG-0137 .599" .641" 6' 5/64" 75 48PTG-0140 .642" .706" 6' 5/64" 75 52PTG-0143 .707" .762" 6' 3/32" 50 46PTG-0146 .763" .820" 6' 3/32" 50 48PTG-0149 .821" .882" 6' 3/32" 50 52PTG-0152 .883" .947" 6' 3/32" 50 56PTG-0155 .948" 1.010" 6' 3/32" 50 58

6' Length

Other sizes available. Please Contact your TVC Customer Service Representative.

www.tvcinc.com

Section 4: Hardware

Washers & Nuts

(888)644-60754 - 66

Square WashersHot Dip Galvanized

Ordering Information

PartNo.

HoleSize (in)

For BoltDia (in)

Approx.Dia. (in)

Ship Wt.(lbs per 100 pcs)

J1073* 2 x 2 x 1/8 9/16 1/2 13.0J1074* 2 x 2 x 1/8 11/16 5/8 13.8J1075* 2-1/4 x 2-1/4 x 3/16 11/16 5/8 26.0

J1076 (E) 2-1/4 x 2-1/4 x 3/16 13/16 3/4 26.8J1078* 3 x 3 x 3/16 7/8 3/4 48.0J1079 3 x 3 x 1/4 7/8 3/4 64.0

J1080 (E) 4 x 4 x 3/16 7/8 3/4 87.0J1082 4 x 4 x 1/4 7/8 3/4 114.0J1081 4 x 4 x 1/2 1-1/8 1 21.6

PartNo.

HoleSize (in)

For BoltDia (in)

Approx.Dia. (in)

Ship Wt.(lbs per 100 pcs)

J6821* 2-1/4 x 2-1/4 x 3/16 11/16 5/8 26.0J6822 2-1/2 x 2-1/2 x 3/16 11/16 5/8 33.0J113* 3 x 3 x 1/4 11/16 5/8 65.0J6823* 3 x 3 x 1/4 13/16 3/4 56.5J133 3-1/4 x 3-1/4 x 1/4 13/16 3/4 76.0J6828 3-1/2 x 3-1/2 x 3/8 15/16 7/8 130.0J6829* 4 x 4 x 1/4 15/16 7/8 117.0

Square Washers

Square Curved Washers

*ANSI Standard (E) REA Accecpted

Square NutsHot Dip Galvanized

Square nuts have always been considered safest to use by utility linemen because of their large wrenchingsurface. Regular nuts are used on all types of threaded bolts and insulator pins, whileheavy nuts are used exclusively on anchor rods.

Joslyn square nuts are manufactured in accordance with American National StandardsInstitute Specifications B18.2.2 and tapped Unified National Coarse Thread Series Class2B after centrifugal hot dip galvanizing, oversize for galvanized bolts and rods.

Ordering Information

PartNo.

Nominal Size Boltand

Threads per Inch

Approx.Ship Wt.

(lbs. Per 100 pcs.)

PartNo.

Nominal Anchor

Rod Dia. (in)

Approx.Ship Wt.

(lbs. Per 100 pcs.)J8561* 3/8"–16 2.2 J8563–1 5/8 12.2J8562* 1/2"–13 5.4 J8564–1 3/4 20.8J8563* 5/8"–11 10.2 J8565–1 1 50.0J8564* 3/4"–10 13.8 J8566 1–1/4 100.0J8564–1/2* 7/8"–9 24.3

Regular Heavy

*ANSI Standard

www.tvcinc.com

Section 4: Hardware

Magic Mile

(888)644-60754 - 67

Suggested Pole Line Construction Material Based On 100 Miles/40 Poles Per Mile

Ordering Information

The above list is only a approximation of items typically required for aerial construction. Consult strand maps for actual bill of materials.

Available in Excel spreadsheet. Call your local TVC representative for details

Description TVCPart No.

Avg./Mile U/M

1/4" EHS Strand - Class A Domestic EHS1/4US 6000 FT.Type 302 Lashing Wire Lifetime Guarantee 045-302LG 6 EA.6" Screw Anchors J6526WCA 6 EA.5/8" x 10" Machine Bolt J8810 12 EA.5/8" x 12" Machine Bolt J8812 5 EA.5/8" x 14" Machine Bolt J8814 15 EA.5/8" x 16" Machine Bolt J8816 10 EA.5/8" x 10" Straight T.E. Bolt J8051 3 EA.5/8" x 12" Straight T.E. Bolt J8052 2 EA.5/8" x 14" Straight T.E. Bolt J8053 4 EA.5/8" x 16" Straight T.E. Bolt J8054 2 EA.2" x 2" sq. Washer 11/16" Hole J1074 100 EA.5/8" Square Nut J8563 50 EA.3 Bolt Suspension Clamp J1096 40 EA.3 Bolt Curved Suspension Clamp J7901A 5 EA.Crossover Clamp 2909970 1 EA.Guy Attachment Strap J25164 12 EA.Guy Marker - Yellow - 8 Ft. PG5718 6 EA.2 PC. Lashing Wire Clamp “D” 2609010 100 EA.10" Zinc Strap 3408911 100 EA.16" Zinc Strap 3408921 50 EA.K - UL Universal Bonding Clamp UL Listed MARKUL 20 EA.1/4" Preformed Splice GLS1104 5 EA.1/4" Guy Grip Deadends GDE1104LA 15 EA.1/2" Plastic Spacer 100-0016-02 100 EA.5/8" x 8' Copper Ground Rod UL Listed W588 10 EA.5/8" Ground Rod Clamp UL Listed MARG5 10 EA.6 Ga. Copper Wire Bare #6AWG 250 FT.1 1/4" x 1/4" Copper Coated Staples J6493 70 EA.2" x 5/8" Galvanized Staples J7487 20 EA.1/2" x 8' Ground Wire Molding 1109 200 FT.