F-4E Phantom

The F-4 Phantom began development in the late 1950’s as a missile armed fighter interceptor. After initial deployment in the 1960’s the remarkable high-speed performance and carrying capacity of the Phantom proved it to be one of the fastest and most versatile fighters to date. Early production units demonstrated one significant shortcoming however, the lack of guns for air-to-air combat. The F-4E solved this problem adding an advanced 20mm cannon for air combat. Markings in this kit include: USAF F-4E, 20 TFS, Holloman AFB, 1997 USAF F-4E, 34 TFS, Korat RTAB, 1972 RAAF F-4E, No 6 Sqn, RAAF Darwin, 1972

Minicraft Models, 1501 Commerce Drive, Elgin IL 60123 USA www.minicraftmodels.com

Printed in China

14621

1 2 3

4

7 8

5 6

14621

Cement Do Not Cement Symmetrical L/ROptional

Your MINICRAFT F-4E includes optional parts for a 'stationary' or 'ground' version with extended landing gear, or 'in-flight' versions. Optional armament of Sparrow and Sidewinder missiles are provided, as well as optional drop tanks. Please review the assembly steps to become familiar with the parts before beginning assembly.

PARTS LAYOUT DIAGRAM

IN-FLIGHT VERSION STATIONARY VERSION

BOTH VERSIONS

2

25 24 23 22 21

26

27

3

9 1011 12

20

19

13

14

8

76

5

4

17

18

28

15

16

1

1

2

23 (Stationary version ONLY)Add noseweight

22

21

4

1615 14

13

20

20

18

17

520

20

19(2X)

19(2X)

6

725

24

8 (Cut)

8 (Cut)

7 (Cut)7 (Cut)

4 (Cut)

28

Cockpit decal(apply first)

4 (Cut)8

9

12

10

Note alignment

11

26

273

Exhausts BURNT METAL

Intake interiors WHITE

Missiles WHITE

Gear struts / doors / bays WHITEHubs ALUMINUM

Tires FLAT BLACK-GRAY

Addnoseweight

Cut gear doorsas shown

F-4E Paint Guide: PAINTS A Black (ModelMaster 1749, Acryl 4768) B FS36270 Neutral Gray (ModelMaster 1725, Acryl 4757) C FS36118 Gunship Gray (ModelMaster 1723, Acryl 4752) D Jet Exhaust (ModelMaster 1796, Acryl 4676) E FS36622 Light Gray (ModelMaster 1733, Acryl 4766) F FS34079 Dark Green (ModelMaster 1710, Acryl 4726) G FS34102 Green (ModelMaster 1713, Acryl 4734) H FS30219 Brown (ModelMaster 1742, Acryl 4709) Decal Application Tips Your Minicraft model includes high-quality waterslide decals. These decals adhere best to a glossy surface; and it is recommended that you apply a clear gloss coat over your painted model. Use a sharp scissors or knife to cut individual decals from the carrier sheet. Do not cut into the clear film surrounding the individual decals.

* It is recommended that you apply one decal at a time. * Place the decal section in warm water, when first inserted in the water your decal will curl, after approximately ten seconds the decal will uncurl. Remove from water and lay on a paper towel. After approximately 10 - 20 seconds the decal will slide freely from the backing paper. Use a small brush to help slide the decal from the backing paper and into position on the model. Carefully blot excess water from the decal, using care not to move the decal or tear it. * If you choose to use a setting solution, apply a thin coat over the decal following the manufacturer’s instruction. * Allow the decal to dry overnight. Wash any adhesive residue off the model with a small amount of clean water and dry thoroughly. * Apply clear gloss, matte or flat coat to seal decals following the instructions from the manufacturer.

1452

1

U

SAF

F-4E

, 20

TFS,

Ho

llom

an A

FB, 1

997

1452

1

USA

F F-

4E, 3

4 TF

S, K

ora

t R

TAB,

197

2

1462

1

RA

AF

F-4E

, No

6 S

qn

, RA

AF

Dar

win

, 197

2