CRAFTSMAN+ - Sears Parts Direct

Owner's Manual

CRAFTSMAN+3.75 HP17 INCH TINE WIDTHFRONT TINE

TILLER

Model No.917.292381

• Safety

Assembly

• Operation• Maintenance• Espanol° Repair Parts

O

CAUTION:

Read and follow all SafetyRules and Instructions beforeoperating this equipment.

Sears, Roebuck and Co., Hoffman Estates, II 60179Visit our Craftsman website:www.sears.com/craffsman

Warranty..................................................2SafetyRules............................................2ProductSprcifications.............................4Assembly................................................5Operation...........................................3&7

Manintenance.......................................1

Service and Adjustments ...................... 1Storage ............................................ 3&1Troubleshooting .................................... 1Illustrated Parts List ............................... 3

Parts Ordering ........................ Back Cow

LIMITED ONE YEAR WARRANTY ON CRAFTSMAN TILLER

For one (1) year from date of purchase, when this Craftsman Tiller is maintained,lubricated, and tuned up according to the operating and maintenance instructions in theowner's manual, Sears will repair free of charge any defect in material or workmanship.This Warranty does not cover:• Expendable items which become worn during norma_ use, such as tines, spark plugs,

air cleaners and belts.

• Repairs necessary because of operator abuse or negligence, including bent crank-shafts and the failure to maintain the equipment according to the instructions con-tained in the owner's manual.

• If this Craftsman Tiller is used for commercial or rental purposes, this Warranty applie.,for only thirty (30) days from the date of purchase.

Warranty service is available by returning the craftsman power mower to the nearestsears service center/department in the united states. This warranty applies only whilethis product is in use in the united states.This Warranty gives you specific legal rights, and you may also have other rights whichvary from state to state.

SEARS, ROEBUCKAND CO., D/817WA, HOFFMAN ESTATES, IL 60179

IMPORTANT: This cutting machine iscapable of amputating hands and feet andthrowing objects. Failure to observe thefollowing safety instructions could result inserious injury or death.

TRAINING• Read the Owner's Manual carefully. Be

thoroughly familiar with the controls andthe proper use of the equipment. Knowhow to stop the unit and disengage thecontrols quickly.

• Never allow children to operate theequipment. Never allow adults tooperate the equipment without properinstruction.

• Keep the area of operation clear of allpersons, particularly small children, andpets.

PREPARATION

• Thoroughly inspect the area where theequipment is to be used and remove allforeign objects.

• Disengage all clutches and shift intoneutral before starting the engine(motor).

• Do not operate the equipment withoutwearing adequate outer garments. Wea_footwear that will improve footing onslippery surfaces.

• Handle fuel with care; it is highlyflammable.

• Use an approved fuel container.• Never add fuel to a running engine or

hot engine.• Fill fuel tank outdoors with extreme care

Never fill fuel tank indoors.• Replace gasoline cap securely and

clean up spilled fuel before restarting.• Use extension cords and receptacles as

specified by the manufacturer for allunits with electric drive motors or electric

starting motors.

2

• Never attempt to make any adjust-ments while the engine (motor) isrunning (except where specificallyrecommended by manufacturer).

OPERATION

• Do not put hands or feet near or underrotating parts.

• Exercise extreme caution when

operating on or crossing gravel drives,walks, or roads. Stay alert for hiddenhazards or traffic. Do not carry passen-gers.

• After striking a foreign object, stop theengine (motor), remove the wire fromthe spark plug, thoroughly inspect thetiller for any damage, and repair thedamage before restarting and operat-ing the tiller.

• Exercise caution to avoid slipping orfalling.

• If the unit should start to vibrate

abnormally, stop the engine (motor)and check immediately for the cause.Vibration is generally a warning oftrouble.

• Stop the engine (motor) when leavingthe operating position.

• Take al_ possible precautions whenleaving the machine unattended.Disengage the tines, shift into neutral,and stop the engine.

• Before cleaning, repairing, or inspect-ing, shut off the engine and makecertain all moving parts have stopped.Disconnect the spark plug wire, andkeep the wire away from the plug toprevent accidental starting. Disconnectthe cord on electric motors.

• Do not run the engine indoors; exhaustfumes are dangerous.

• Never operate the tiller without properguards, plates, or other safety protec-tive devices in place.

• Keep children and pets away.• Do not overload the machine capacity

by attempting to till too deep at too fasta rate.

• Never operate the machine at highspeeds on slippery surfaces. Lookbehind and use care when backing.

• Never allow bystanders near the unit.• Use only attachments and accessories

approved by the manufacturer of thetiller.

• Never operate the tiller without goodvisibility or light.

• Be careful when tilling in hard ground.The tines may catch in the ground andpropel the tiller forward. If this occurs,let go of the handlebars and do notrestrain the machine.

MAINTENANCE AND STORAGE

• Keep machine, attachments, andaccessories in safe working condition.

• Check shear pins, engine mountingbolts, and other bolts at frequentintervals for proper tightness to be surethe equipment is in safe workingcondition.

• Never store the machine with fuel in the

fuel tank inside a building whereignition sources are present, such ashot water and space heaters, clothesdryers, and the like. Allow the engine tocool before storing in any enclosure.

• Always refer to the operator's guideinstructions for important details if thetiller is to be stored for an extended

period._l, Look for this symbol to point outimportant safety precautions. It meansCAUTION!!! BECOME AWARE!!! YOURSAFETY IS INVOLVED.

_,CAUTION: Always disconnect sparkplug wire and place wire where it cannotcontact spark plug in order to preventaccidental starting when setting up,transporting, adjusting or making repairs._WARNING: The engine exhuast fromthis product contains chemicals known tothe State of California to cause cancer,birth defects or other reproductive harm.

3

PRODUCT SPECIFICATIONS

GASOLINE 2 QTS

CAPACITY: UNLEADED

REGULAR

OlL(API-SF/SG/SH): SAE 30

CAPACITY: 20 OZ.) (ABOVE 32°F)SAE 5W-30

(BELOW 32°F)

SPARK PLUG : CHAMPION

(GAP: .030") RJ19LM OR J19LM

Congratulations on your purchase of aSears Tiller. It has been designed,engineered and manufactured to give youthe best possible dependability andperformance.Should you experience any problems youcannot easily remedy, please contactyour nearest authorized Sears ServiceCenter/Department. We have competent,well-trained technicians and the propertools to service or repair this unit.Please read and retain this manual. The

instructions will enable you to assembleand maintain your tiller properly. Alwaysobserve the "SAFETY RULES".Your new tiller has been assembled at the

factory with exception of those parts leftunassembled tot shipping purposes. Toensure safe and proper operation of yourtiller all parts and hardware you assemblemust be tightened securely. Use thecorrect tools as necessary to insureproper tightness,

CUSTOMER RESPONSIBILITIES

• Read and observe the safety rules.• Follow a regular schedule in maintain-

ing, caring for and using your tiller.• Follow the instructions under the

"Maintenance" and "Storage" sectionsof this Owner's Manual.

WARNING: This unit is equipped withan internal combustion engine and shoulcnot be used on or near any unimprovedforest-covered, brush-covered or grasscovered land unless the engine's exhaustsystem is equipped with a spark arrestermeeting applicable local or state laws (ifany). If a spark arrester is used, it shouldbe maintained in effective working orderby the operator.In the state of California the above isrequired by law (Section 4442 of theCalifornia Public Resources Code). Otherstates may have similar laws. Federallaws apply on federal lands. See yourSears Authorized Service Center for spafl,arrester. Refertothe Repair Parts sectionof this manual for part number.

These accessodes were available when the tiller was purchased, They are alsoavailable at most Sears Retail outlets and Service Centers. Most Sears Stores can

order repair parts for you when you provide the model number of your tiller.ENGINE

TILLER MAINTENANCE

BELT ' TINES SHEAR PIN HAIRPIN CLIP

4

Your new tiller has been assembled at the tactory with exception of those parts leftunassembled for shipping purposes. To ensure safe and proper operation of your tillerall parts and hardware you assemble must be tightened securely. Use the correct toolsas necessary to insure proper tightness.

TOOLS REQUIRED FOR ASSEMBLY

A socket wrench set will make assemblyeasier. Standard wrench sizes are listed.

(1) Utility knife(1) Pair of pliers(2) 1/2 Wrench

OPERATOR'S POSITION

When right or left hand is mentioned inthis manual, it means when you are inthe operating position (standing behindtiller handles).

LEFT

FRONT

RIGHT

OPERATOR'SPOSITION

CONTENTS OF HARDWARE PACK

Hex Bolts8 x 314 5/16-18 x 1 5/16-18 x 1-1/4

©(6) Hex Nuts

5/16-18(1) BottleEngine Oil

(4) Washers3/8 x 7/8 x 14 Ga.

(6) LockWashers 5/16

5

UNPACK CARTON & INSTALLHANDLE

_CAUTION: Be careful of exposedstaples when handling or disposing ofcartoning material.IMPORTANT: When unpacking andassembling tiller, be careful not to stretchor kink cable(s).• Cut cable ties securing handles.• The handle may be assembled in high

or low position. Slowly lift handleassembly up and align handle holeswith desired handle panel hole and slot.

• Loosely assemble hardware as shown.Be sure the shorter (3/4" long) hex boltis assembled in lower hole of handle.

Repeat for opposite side. Tighten allhardware securely.

• Cut cable ties securing tiller to skid andremove tiller from skid.

Handle PanelNut,

• LockWasher

Washer

€Bolt5/16-18 x 1"

Hex Bolts5/16-18 x 3/4"

INSTALL DEPTH STAKEASSEMBLY

• Loosen nut "A".

• Insert stake support between enginebracket halves with stake spring down.

• Bolt stake support to engine bracketswith bolts, lock washers and nuts.Tighten securely. Tighten nut "A".

• Depth stake must move freely. If it doesnot, loosen support belt.

\

qut "A"Depth Stake

Stake

Support Bolt

Hex Bolts, Lockwashers,and Hex Nuts

HANDLE HEIGHT

• Handle height may be adjusted to bettersuit operator. (See "HANDLE HEIGHT"in the Service and Adjustments sectionof this manual).

TILLING WIDTH

• Tilling width may be adjusted to betterhandle your tilling conditions (See =TINEARRANGEMENT" in the Service and

Adjustments section of this manual).

TINE OPERATION

• Check tine operation before first use.(See "TINE OPERATION CHECK" inthe Service and Adjustments section ofthis manual).

6

These symbols may appear on your 1311eror in literature supplied with the product. Learnand understand their meeting.

KNOW YOUR TILLER

READ THIS OWNER'S MANUALAND SAFETY RULES BEFORE OPERATING YOURTILLER.

Compare the illustrations with your tiller to familiarize with the location of variouscontrols and adjustments. Save this manual for future reference.

_RUJ_ FOf_N_I,_ NIELr{ _4&. _RSIE CN3T_N _NqE ENgiNE _FJ,ST SLOW C_(_E FUEL C4t V

OR WARNING ON O_F

Throttle Control

Depth Stake

TineShield

Recoil Starter HandleTines

MEETS ANSI SAFETY REQUIREMENTS

Our tillers conform to the safety standards of the American National Standards Institute.

FORWARD TINE CONTROL - Engagestines in forward direction.

CHOKE CONTROL - Used when startinga cold engine.THROTTLE CONTROL - Controls enginespeed,

DEPTH STAKE - Controls forward speedand the depth at which the tiller will dig.RECOIL STARTER HANDLE - Used to

start the engine.

7

The operation of any tiller can result in foreign objects thrown into the eyes,which can result in severe eye damage. Always wear safety glasses or eyeshields before starting your tiller and while tilling. We recommend a widevision safety mask over spectacles or standard safety glasses.

HOWTO USE YOUR TILLER

Know how to operate all controls beforeadding fuel and oil or attempting to startengine.

STOPPINGTINES

WHEELS

Adjust wheels by removing the hairpin clipand clevis pin. Change wheel position.Replace the hairpin clip and clevis pin.• For normal tilling, set wheels at the

second or third hole from the top.

• Release tine control to stop movement.ENGINE

• Move throttle control to "STOP" position.• Never use choke to stop engine.

\

Hairpin Clip and

Depth Stake

Forward "FineControl"On" (DOWN)

Control"OFF' (UP) Position

/ ThrottleControl

ChokeControl

TINE OPERATION

• Squeeze tine control to handle.

TILLING

The speed and depth of tilling is regulatedby the position of the depth stake andwheel height.The depth stake should always be belowthe wheels for digging. It serves as abrake to slow the tiller's forward motion to

enable the tines to penetrate the ground.Also, the more the depth stake is loweredinto the ground the deeper the tines willdig.

DEPTH STAKEAdjust depth stake by removing the hairpinclip and clevis pin. Change depth stake todesired position. Replace the clevis pinand hairpin clip.• For normal tilling, set depth stake at the

second or third hole from the top.

Hairpin Clip andWheel Clevis Pin

TO TRANSPORT

ACAUTION: Before lifting or transporting.allow tiller engine and muffler to cool.Disconnect spark plug wire. Draingasoline from fuel tank.AROUND THE YARD

• Tip depth stake forward until it is held bythe stake spring.

• Push tiller handles down, raising tines offthe ground.

• Push or pull tiller to desired location.AROUND TOWN

• Disconnect spark plug wire.• Drain fueltank.

• Transport in upright position to preventoil leakage.

BEFORE STARTING ENGINE

IMPORTANT: Be very careful not to allowdirt to enter the engine when checking oradding oil or fuel. Use clean oil and fueland store in approved, clean, coveredcontainers, use clean fill funnels.FILL ENGINE WITH OIL

• Remove hangtag from engine.• With engine level, remove engine oil

filler plug.• Fill engine with oil to point of overflow-

ing. For approximate capacity see"PRODUCT SPECIFICATIONS".

• Tilt tiller back on its wheels and then re-level.

8

• With engine level, refill to point ofoverflowing if necessary. Replace oilfiller plug.

• For cold weather operation you shouldchange oil for easier starting (See =OILVISCOSITY CHART" in the Mainte-nance section of this manual).

• To change engine oil, see the Mainte-nance section of this manual.

Oil FillerOil Level Plug

ADD GASOLINE• Fill fuel tank. Use fresh, clean, regular

unleaded gasoline. (Use of leadedgasoline will increase carbon and leadoxide deposits and reduce valve life.)

IMPORTANT: When operating in tempera-tures below 32°F(0°C), use fresh, clean,winter grade gasoline to help insure goodcold weather starting.AWARNING: Experience indicates thatalcohol blended fuels (called gasohol orusing ethanol or methanol) can attractmoisture which leads to separation andformation of acids during storage. Acidicgas can damage the fuel system of anengine while in storage. To avoid engineproblems, the fuel system should beemptied before storage of 30 days orlonger, Drain the gas tank, start theengine and let it run until the fuel lines andcarburetor are empty. Use fresh fuel nextseason. See Storage section of thismanual for additional information. Never

use engine or carburetor cleaner productsin the fuel tank or permanent damage mayoccur.

_CAUTION: Fill to within 112 inch of top offuel tank to prevent spills and to allow forfuel expansion. If gasoline is accidentallyspilled, move machine away from area ofspill. Avoid creating any source of ignitionuntil gasoline vapors have disappeared.Do not overfill. Wipe off any spilled oil orfuel. Do not store, spill or use gasolinenear an open flame.

TO START ENGINE

_:LCAUTION: Keep tine control in "OFF"position when starting engine.When starting engine for the first time or ifengine has run out of fuel, it will take extrapulls of the recoil starter to move fuel fromthe tank to the engine.• Make sure spark plug wire is properly

connected.

• Place throttle control in "FAST" position.• Move choke control to full "CHOKE"

position. Grasp recoil starter handle withone hand and grasp tiller handle withother hand. Pull rope out slowly untilengine reaches start of compressioncycle (rope will pull slightly harder at thispoint).

• Pull recoil starter handle quickly. Do no1let starter handle snap back againststarter. Repeat if necessary.

• If engine fires but does not start, movechoke control to half choke position. Pulrecoil starter handle until engine starts.

• When engine starts, slowly move chokecontrol to "RUN" position as enginewarms up.

NOTE: A warm engine requires lesschoking to start.• Move throttle control to desired running

position.• Allow engine to warm up for a few

minutes before engaging tines.NOTE: If at a high altitude (3000 feet) orin cold temperatures (below 32°F), thecarburetor fuel mixture may need to beadjusted for best engine performance.See %0 ADJUST CARBURETOR" in the

Service and Adjustments section of thismanual.

NOTE: If engine does not start, seetroubleshooting points,

Control

Control

9

BREAKING IN YOUR TILLERBreak-in your belt(s), pulleys and tinecontrol before you actually begin tilling.• Start engine, tip tines off ground by

pressing handles down and engage tinecontrol to start line rotation. Allow tinesto rotate for five minutes.

• Check tine operation and adjust ifnecessary. See "TINE OPERATIONCHECK" in the Service and Adjustmentssection of this manual.

TILLING HINTS

ACAUTION: Until you are accustomed tohandling your tiller, start actual field usewith throttle in slow position.To help tiller move forward, lift up thehandles slightly (thus lifting depth stakeout of ground). To slow down the tiller,press down on handles.If you are straining or tiller is shaking, thewheels and depth stake are not setproperly in the soil being tilled. The propersetting of the wheels and depth stake isthrough trial and error and depends uponthe soil condition. (The harder or wetterthe ground, the slower the engine and tinespeed needed. Under these poor condi-tions, at fast speed the tiller will run andjump over the ground).A properly adjusted tiller will dig with littleeffort from the operator.* Tilling is digging into, turning over, and

breaking up packed soil before planting.Loose, unpacked soil helps root growth.Best tilling depth is 4"-6". A tiller willalso clear the soil of unwanted vegeta-tion. The decomposition of this veg-etable matter enriches the soil. De-

pending on the climate (rainfall andwind), it may be advisable to till the soilat the end of the growing season tofurther condition the soil.

. Soil conditions are important for propertilling. Tines will not readily penetratedry, hard soil which may contribute toexcessive bounce and difficult handlingof your tiller. Hard soil should bemoistened before tilling; however,extremely wet soil will "ball-up" or clumpduring tilling. Wait until the soil is lesswet in order to achieve the best results.When tilling in the fall, remove vines andlong grass to prevent them fromwrapping around the tine shaft andslowing your tilling operation.

10

• You will find tilling much easier if youleave a row untilled between passes.Then go back between tilled rows.There are two reasons for doing this.First, wide turns are much easier tonegotiate than about-faces. Second, tltiller won't be pulling itself, and you,toward the row next to it.

• Set depth stake and wheel height forshallow tilling when working extremelyhard soil or sod. Then work across thefirst cuts at normal depth.

CULTIVATING

Cultivating is destroying the weeds be-tween rows to prevent them from robbingnourishment and moisture from the plant-,At the same time, breaking up the upperlayer of soil crust will help retain moisturein the soil. Best digging depth is 1"-3".• You will probably not need to use the

depth stake. Begin by tipping the depthstake forward until it is held by the stakespring.

• Cultivate up and down the rows at aspeed which will allow tines to uprootweeds and leave the ground in roughcondition, promoting no further growth cweeds and grass.

OOOOOOOOOO

i

OOO O O

MAINTENANCESCHEDULE

FiLL IN DATES 6<" _AS YOU COMPLETE SERVICE DATESREGULAR SERVICE

Check Engine Oil Level V' I_

Change Engine Oil _1,_

Oil Pivot Points

inspect Spark Arrestar / Muffler V'

Inspect Air Screen I_

Clean or Replace Air Cleaner Cartridge I_ 2

Clean Engine Cylinder Fins

Replace Spark Plug if

I - Change more often when operating under a heavy load or in high ambient temperatures.2 - Service more often when operating in dirty or dusty conditions,

GENERAL RECOMMENDATIONS

The warranty on this tiller does not coveritems that have been subjected tooperator abuse or negligence. To receivefull value from the warranty, the operatormust maintain tiller as instructed in thismanual.

Some adjustments will need to be madeperiodically to properly maintain your tiller.All adjustments in the Service andAdjustments section of this manual shouldbe checked at least once each season.

• Once a year you should replace thespark plug, clean or replace air filter,and check tines and belts for wear. A

new spark plug and clean air filterassure proper air-fuel mixture and helpyour engine run better and last longer.

BEFORE EACH USE

• Check engine oil level.• Checktine operation.• Check for loose fasteners.LUBRICATION

Keep unit well lubricated (See "LUBRICA-TION CHART")

LUBRICATION

*Idler Arm

* SAE30 or 10W-30 Motor Oil** Refer to Maintenance "ENGINE" Section

11

ACAUTION: Disconnect spark plug wirebefore performing any maintenance(except carburetor adjustment) to preventaccidental starting of engine.Prevent fires! Keep the engine free ofgrass, leaves, spilled oil, or fuel. Removefuel from tank before tipping unit formaintenance. Clean muffler area of all

grass, dirt, and debris.Do not touch hot muffler or cylinder fins ascontact may cause burns.

ENGINELUBRICATION

Use only high quality detergent oil ratedwith API service classification SF, SG orSH. Select the oil's SAE viscosity gradeaccording to your expected temperature.

SAE VISCOSITY GRADES

oc ._, o, 30,TEMPERATURE RANGE ANTtCIPATED BEFORE NEXT OIL CHANGE

NOTE: Although multi-viscosity oils (5W-30, 10W-30, etc.) improve starting in coldweather, these multi-viscosity oils willresult in increased oil consumption whenused above 32°F (0°C). Check yourengine oil level more frequently to avoidpossible engine damage from running lowon oil.

Change the oil after every 50 hours ofoperation or at least once a year if the tilleris not used for 50 hours in one year.Check the crankcase oil level before

starting the engine and after each five (5)hours of continuous use. Add SAE 30motor oil or equivalent. Tighten oil fillerplug securely each time you check the oillevel.TO CHANGE ENGINE OIL

Determine temperature range expectedbefore oil change. All oil must meet APIservice classification SF, SG or SH.• Be sure tiller is on level surface.

• Oil will drain more freely when warm.• Catch oil in a suitable container.• Remove drain plug.• Tip tiller forward to drain oil.• After oil has drained completely, replace

oil drain plug and tighten securely.• Remove oil filler plug. Be careful not to

allow dirt to enter the engine.• Refill engine with oil. See "CHECK

ENGINE OIL LEVEL" in the Operationsection of this manual.

OilDrainPlug_

Oil LevelOil Filler Plug

AIR CLEANER

Service air cleaner cartridge everytwenty-five hours, more often if engine isused in very dusty conditions.• Loosen air cleaner screws, one on each

side of cover.• Remove air cleaner cover.

• Carefully remove air cleaner cartridge.Be careful. Do not allow dirt or debris tofall into carburetor.

• Clean by tapping gently on a flatsurface.

• If very dirty or damaged, replacecartridge.

• Clean and replace cover. Tightenscrews securely.

_t,CAUTION: Petroleum solvents, such askerosene, are not to be used to cleancartridge. They may cause deterioration ofthe cartridge. Do not oil cartridge. Do notuse pressurized air to clean or drycartridge.

Cleaner

AirCleanerCartridge

COOLING SYSTEM

Your engine is air cooled. For properengine performance and long life keepyour engine clean.• Clean air screen frequently using a stiff-

bristled brush.

• Remove blower housing and clean asnecessary.

• Keep cylinder fins free of dirt and chaff.

12

Muffier_ y,nTer HnsBlower

)ous,ogA "_'-'-,_,. iI_F- ./Air

ScreenMUFFLER

Do not operate tiller without muffler. Do nottamper with exhaust system. Damagedmufflers or spark arresters could create afire hazard. Inspect periodically andreplace if necessary. If your engine isequipped with a spark arrester screenassembly, remove every 50 hours forcleaning and inspection. Replace ifdamaged.

SPARK PLUG

Replace spark plugs at the beginning ofeach tilling season or after every 50 hoursof use, whichever comes first. Spark plugtype and gap setting are shown in"PRODUCT SPECIFICATIONS".

TRANSMISSIONYour transmission is sealed and will notrequire lubrication unless serviced.

CLEANING

* Clean engine, wheels, finish, etc. of allforeign matter.

, Keep finished surfaces and wheels freeof all gasoline, oil, etc.

• Protect painted surfaces with automo-tive type wax.

We do not recommend using a gardenhose to clean you_ unit unless the muffler,air filter and carburetor are covered to

keep water out. Water in engine can resultin a shortened engine life.

_},CAUTION: Disconnect spark p!ug wi_efrom spark plug and place wire where itcannot come into contact with plug.

TILLER

TO ADJUST HANDLE HEIGHT

Factory assembly has provided lowesthandle heighL Select handle height bestsuited for your tilling conditions. Handleheight will be different when tiller digs intosoil.

• If a higher handle height is desired,loosen the four nuts securing handlepanel to engine brackets.

• Slide handle panel to desired location.• Tighten the four nuts securely.

_=Br_ it_tHandle Pane!

°_tli_lffr_ide

TINE ARRANGEMENT

Your outer tines can be assembled in

several different ways to suit your tilling orcultivating needs,_CAUTION: Tines are sharp. Weargloves or other protection when handlingtines.NORMAL TILLING - 17" PATH

° Assemble holes "A" in tine hubs to holes"B" in tine shaft.

inotrTinMID-WIDTH TILLING - 15" PATH

= Assemble holes "A" in tine hubs to holes"C" in tine shaft.

0 0

13

NARROW TILLING/CULTIVATING -10-114" PATH• Remove outer tines.

_ merTines Or

oo]

NARROW CULTIVATING - 12-112" PATH

• Remove inner tines.• Assemble holes "A" in tine hubs to holes

"C" in tine shaft.

EDGING - 9-5/8" PATH

• Remove inner tines.• Assemble holes "A" in tine hubs to holes

"D" in tine shaft.

NOTE: When reassembling outer tinesbe sure right tine assembly (marked "R"and left tine assembly (marked "L") aremounted to correct side of tine shaft.

TINE OPERATION CHECK

Be sure tines do not rotate when engine isrunning and tine control is in the "OFF"position._CAUTION: Disconnect spark plug wirefrom spark plug to prevent starting whilechecking tine operation.FINAL CHECK "OFF" POSITION

• With tine control "OFF" (up), push downon handle to raise tines off the ground.

• Slowly pull recoil starter handle whileobserving tines. Tines should notrotate.

• If tines rotate, place loop of idler springin a lower link of chain and retest.

FINAL CHECK "ON" POSITION

• With tine control "ON" (held down tohandle) push down on handle to raisetines off the ground.

• Slowly pull recoil starter handle whileobserving tines. Tines should rotateforward.

• If tines do not rotate, place loop of idlespring in a higher link of chain andretest.

NOTE: If "ON" position check requiredadjustment, recheck "OFF' positionadjustment to insure tines do not rotatewhen control is "OFF" (up).

Chain

/

\

\TO REMOVE BELT GUARD

• Remove cap nut and washer from sideof belt guard.

• Pull belt guard out and away from unit.• Replace belt guard by reversing above

procedure. Be sure slot in bottom ofbelt guard is under head of tine shieldbolt and all nuts are tightened securely

Sc[ew

Belt Guard

rew

14

TO REPLACE V-BELTReplace V-belt if it has stretched consider-ably or if it has cracks or frayed edges.Belt guard must be removed to servicebelt. See "TO REMOVE BELT GUARD" inthis section of manual.BELT REMOVAL

• Remove V-belt from transmission pulleyfirst and then from engine pulley.

BELT REPLACEMENT

• Install new V-belt to engine pulley firstthen to transmission pulley. Be surebelt is positioned on inside groove ofboth pulleys, inside all belt guides andrests on idler pulley.

CHECK TINE OPERATION

• See "TINE OPERATION CHECK" in thissection of manual.

REPLACE BELT GUARD

Belt Guide

Engine

FINAL SETTING

• Start engine and allow to warm for fiveminutes.

• With throttle control in "SLOW" positionIDLE RPM ADJUSTMENT

• To adjust idle RPM, rotate throttlelinkage counterclockwise and holdagainst stop while adjusting idle speedadjusting screw to obtain 1750 RPM.Release throttle linkage.

High speed stop is factory adjusted. Donot adjust or damage may result.IMPORTANT: Never tamper with theengine governor, which is factory set forproper engine speed, overspeeding theengine above the factory high speedsetting can be dangerous. If you think theengine-governed high speed needsadjusting, contact your nearest authorizecservice center/department, which has theproper equipment and experience to makany necessary adjustments,

Throttle Throttle Stop

\TransmissionPulley

ENGINEMaintenance, repair, or replacement of theemission control devices and systems,which are being done at the customersexpense, may be performed by any non-road engine repair establishment orindividual. Warranty repairs must beperformed by an authorized enginemanufacturer's service outlet.TO ADJUST CARBURETOR

The carburetor has a high speed fixed jetand has been preset at the factory andadjustment should not be necessary.However, minor adjustments may berequired to compensate for differences infuel, temperature, altitude or load. If thecarburetor does need adjustment, proceedas follows.

Idle speedAdjusting Screw

Immediately prepare your tiller for storageat the end of the season or if the unit will

not be used for 30 days or more._CAUTION: Never store the tiller withgasoline in the tank inside a buildingwhere fumes may reach an open flame orspark. Allow the engine to cool beforestoring in any enclosure.

TILLER

• Clean entire tiller (See "CLEANING" inthe Maintenance section of thismanual).

• Inspect and replace belts, if necessary(See belt replacement instructions in theService and Adjustments section of thismanual).

• Lubricate as shown in the Maintenancesection of this manual.

• Be sure that all nuts, bolts and screwsare securely fastened. Inspect movingparts for damage, breakage and wear.Replace if necessary.

• Touch up all rusted or chipped paintsurfaces; sand lightly before painting.

ENGINEFUELSYSTEM

IMPORTANT: It is important to preventgum deposits from forming in essentialfuel system parts such as the carburetor,fuel _ter, fuel hose, or tank during storage.also, experience indicates that alcoholblended tuets (called gasohol or usingethanol or methanol) can attract moisturewhich leads to separation and formation ofacids during storage. Acidic gas candamage the fuel system of an enginewhile in storage.• Drain the fuel tank.

• Start the engine and let it run until thefuel lines and carburetor are empty.

• Never use engine or carburetor cleanerproducts in the fuel tank or permanentdamage may occur.

• U,;e fresh fuel next season.

NOTE: Fuel stabilizer is an acceptablealternative in minimizing the formation offuel gum deposits during storage. Addstabilizer to gasoline in fuel tank or storagecontainer. Always follow the mix ratiofound on stabilizer container. Run engineat least 10 minutes after adding stabilizerto a_ow the stabilizer to reach the carbure-tor. Do not drain the gas tank andcarburetor if using fuel stabilizer.

ENGINE OIL

Drain oil (with engine warm) and replacewith clean oil. (See "ENGINE" in theMaintenance section of this manual).

CYLINDER(S)

• Remove spark plug.• Pour 1 ounce (29 ml) of oil through

spark plug hole into cylinder.• Pull starter handle slowly several times

to distribute oil.

• Replace with new spark plug.

OTHER

• Do not store gasoline from one seasonto another.

• Replace your gasoline can if your canstarts to rust. Rust and/or dirt in yourgasoline will cause problems.

• If possible, store your unit indoors andcover it to give protection from dust anddirt.

• Cover your unit with a suitable protec-tive cover that does not retain moisture.Do not use plastic. Plastic cannotbreathe which allows condensation to

form and will cause your unit to rust.IMPORTANT: Never cover tiller while

engine and exhaust areas are still warm.

16

II II

PROBLEM

Will not start

Hard to start

Loss of power

CAUSE

1. Out of fuel.2. Engine not "CHOKED"

properly.3. Engine flooded.

4. Dirty air cleaner.

5. Water in fuel.

6. Clogged fuel tank.7. Loose spark plug wire.

8. Bad spark plug orimproper gap.

9. Carburetor out of adjust-ment.

1. Throttle control not setproperly.


3. Bad spark plug orimproper gap.

4, Stale or dirty fuel.

5. Loose spark plug wire.

6. Carburetor out of

adjustment.

1. Engine is overloaded.


3. Low oil level/dirty oil.4. Faulty spark plug.

5. Oil in fuel.

6. Stale or dirty fuel.

7. Water in fuel.

8. Clogged fuel tank.9. Spark plug wire loose.

10, Dirty engine air screen.11. Dirty/clogged muffler.12. Carburetor out of

adjustment.13. Poor compression.

CORRECTION

1. Fill fuel tank.2. See "TO START ENGINE" in

the Operation section.3. Wait several minutes before

attempting to start.4. Clean or replace air cleaner

cartridge.5. Drain fuel tank and carbure-

tor, and refill tank with freshgasoline.

6. Remove fuel tank and clean.

7. Make sure spark plug wire isseated properly on plug.

8. Replace spark plug or adjustgap.

9. Make necessary adjustments,

1. Place throttle control in"FAST" position.

2. Clean or replace air cleanercartridge.

3. Replace spark plug or adjustgap.

4. Drain fuel tank and refill withfresh gasoline.

5. Make sure spark plug wire isseated properly on plug.

6, Make necessary adjustments.

1. Set depth stake and wheelsfor shallower tilling.

2. Clean or replace air cleanercartridge.

3. Check oil level/change oil.4. Clean and regap or change

spark plug.5. Drain and clean fuel tank and

refill, and clean carburetor.6, Drain fuel tank and refill with

fresh gasoline.7. Drain fuel tank and carbure-

tor, and refill tank with freshgasoline.

8. Remove fuel tank and clean.9. Connect and tighten spark

plug wire.10. Clean engine air screen.11. Clean/replace muffler.12. Make necessary adjustments.

13. Contact an authorized SearsService Center/Department.

17

CAUSE CORRECTIONPROBLEM

Engine overheats

Excessivebounce/difficult

handling

Soil balls up orclumps

Engine runs buttiller won't move

Engine runs butlabors when tilling

1. Low oil level/dirty oil.2. Dirty engine air screen.3. Dirty engine.

4. Partially plugged muffler.5. Improper carburetor

adjustment.

1. Ground too dry and hard.

2. Wheels and depth stakeincorrectly adjusted.

1. Ground too wet.

1. Tine control is notengaged.

2. V-belt not correctlyadjusted.

3. V-belt is off pulley(s).

1, Tilling too deep.

2. Throttle control not

setting.3. Carburetor out of

adjustment.

1. Check oil level/change oil.2. Clean engine air screen.3. Clean cylinder fins, air

screen, muffler area.4. Remove and clean muffler.5. Adjust carburetor to richer

position,

1. Moisten ground or wait formore favorable soil condition_

2. Adjust wheels and depthstake.

1. Wait for more favorablesoil conditions.

1. Engage tine control.

2. Inspect/adjust V-belt.

3. Inspect V-belt.

1. Set depth stake for shallowertilling.

2. Check throttle control properlyadjusted.

3. Make necessary adjustments.

18

TILLER - - MODEL NUMBER 917.292381

HANDLE ASSEMBLY

KEY PARTNO. NO,

1 137176X4312 72140512

3 9266R4 1514735 7368O5OO6 191111167 191214i_6 747605169 7476051210 1O04059O11 7322050012 98000129

16

DESCRIPTION

Bracket, Handle*Bolt, Carriage5/16-18 UNC x 1-1/2Gnp, HandleHandle, LH.*Locknut, Crown 5/16-18*Washer 11/32 x 11/16 x 16 Ga.*Washer 3/8 x 7/8 x 14 Ga.Bolt, Hex Hd 5/16-18 x 1Bolt, Hex Hd 5/16-18 x 3/4"Washer, Lock 5!16*Nut, Hex 5/16-16*Nut, Flanged 5/16-18

33

19

KEY PARTNO, NO.

13 72140506

14 9209R43115 7476052416 15147418 3067J19 16493728 1913131233 8206H34 3070J

DESCRIPTION

*Bolt, Carriage 5/16-18 x 3/4Gr. 5Panel, Handle*Bolt, Hex 5/16-i8x 1-1/2Handle, R.H.Cable, Control, TineLever, Clutch 8.00Washer 13/32 x 13/16 x 12 Ga.Grip, LeverSpring, Extension

*STANDARD HARDWARE--PURCHASE LOCALLY

NOTE: All component dimensions given in U.S.inches. 1 inch = 25.4 mm

36


BELT GUARD AND PULLEY ASSEMBLY

KEY PARTNO. NO.1 23230506

2 1308124 746108125 174904406 1657707 1655038 9223R9 165768X558

10 109227X12 9180R13 1200002814 151223

DESCRIPTIONKEY PARTNO. NO.

*Screw, Set, Forged Socket, 15 165504Headless 5/16-18x3/8 16 12000036Sheave, Engine 17 73350600Bolt, Hex 1/2-20 x 3/4 18 161806Bott,Thd Roller 1/4-20 x 2-1/2 19 162290Shield, Inner Guard Bit Ft 20 74760620Screw Hex Wsh Hd #8-18 x !/2 21 106968XSpacer, Split 25 73350500Guard, BeltPad, IdlerV-BeltRing, RetainerSheave, Transmission

DESCRIPTION

Nut, J ClipRing,Klip

*Nut, Hex, Jam 3/8-16Pulley, IdlerIdler Arm Assembl'g"Bolt, Hex 3/8-16 x 1-1/4Shaft, IdlerAnn"Nut, Hex, Jam 5/16-18

*STANDARD HARDWARE--PURCHASE LOCALLY

NOTE: Allcomponent dimensions given in U.S.ir',ches.1 inch = 25.4 mm

37


WHEEL AND DEPTH STAKE ASSEMBLY

112

16

247

2

16

47

17

2O19

18

17

KEY PART KEY PARTNO. NO. DESCRIPTION NO. NO.

1 9194R PinClevis 15 5388J2 74760520 *Bolt, Hex 5/16-18x1-1/4 15 121117X3 STD523107 BoltHex Hd 5/16-18 UNC x 3/4 17 9186R4 STD541031 *Nut, Hex 5/16-18 18 STD5510375 STD551131 *Washer, Lock 5/16 19 9190R6 STD541437 Locknut, W/'msert3/8-16 20 STD5414377 4921H Clip, Hairpin 21 747605168 318J Support, Depth Stake, R.H. 22 STD5414319 9193R Depth Stake

10 9551R Pin, Clevis11 74780628 Bolt, Fin, Hex 3/8-t6 x 1-3/412 74760524 Bolt, Hex 5/16-18 X 1-1/213 317J Support, Depth Stake, LH.

DESCRIPTION

Spring, Depth StakeBolt,ShoulderWheel*Washer 13/32 x 13/16 x 11 GaBracket, Wheel*Nut, Crownlock 3/8-16Bolt Hex 5/16-18 x 1Locknut, W/insert 5/16-18

*STANDARD HARDWARE--PURCHASE LOCALL3

NOTE: All componentdimensionsgiven in U.S.inches. 1 inch = 25.4 mm

38


TINE ASSEMBLY

/

6

2

3

KEY PARTNO. NO. DESCRIPTION

1 165774 Tine, Outer, R.H.2 4921H Clip, Hairpin3 165772 Tine, lnner, R.H.

KEY PARTNO. NO. DESCRIPTION

4 165771 Tine, lnner, L.H.5 165773 Tine, Outer, L.H6 9194R Pin, Clevis

39

TRANSMISSION


1514

14

14

I0

KEY PARTNO. NO.

1 747605242 STD5237323 STD5510375 STD5414376 9056R5587 1658358 1658349 STD551131

10 STD54103111 7476054412 15193714 9173R

DESCRIPTION

Bolt, Hex 5/16-18 x 1-1/2 Gr. 2Bolt, Fin, Hex 3/8-16 x 3-1/4Washer 13/32 x 13/16 x 11Locknut,w/washer 3/8.16Shield,TineBracket, Engine, R.H.Bracket, Engine, LH.Washer, Lock 5/16Nut, Hex 5/16-18Bolt, Hex Hd 5/16-18 x 2-3/4TransmissionSpacer, Split

KEY PARTNO. NO.

15 STD54143116 1909141217 1909201618 STD55112519 746104122O

DESCRIPTION

Nut, Keps 5/16-18Washer 9/32 x 7/8 x 12 Ga.Washer 9/32 x 1-1/4 x 16 Ga.Washer, Lock 1/4Bolt. Hex 1/4-28 x 3/4 Gr. 5Engine, Bdggs& StrattonModel No. 94202-0115-E1

"STANDARDHARDWARE--PURCHASELOCALLY

NOTE: All componentdimensionsgiven in U.S.inches. 1 inch = 25.4 mm

4O

DECALS

TILLER - - MODEL NUMBER 917,292381

5

63

9

4 10

KEY PARTNO, NO, DESCRIPTION

2 166128 Decal, Logo3 165327 Decal, Engine Ref.4 166129 Decal, BeltGuard'Fine Shield5 110594X Decal, Control Pnl Inst.6 120431X Decal, Hand Placement7 110719X Decal, Oper/Lubdcation8 120075X Decal, Warning, Rotating Tines9 171803 Decal, Engine10 171920 Decal, HP11 162215 Decal, Tine ShieldWrng Dom12 163165 Decat, ControIPanel- - 172054 Manual, Owner's (Eng/Span)

41


BRIGGS & STRATTON ENGINE - MODEL NUMBER 94202, TYPE NO,0115-E1

11307

635

_13 308

26

42


BRIGGS & STRATI'ON ENGINE - MODEL NUMBER 94202, TYPE NO.0115-E1

i

_7=_ €

J 1036'LABEL KIT- EMISSION I

373

455

332

304

43


BRIGGS & STRATTON ENGINE - MODEL NUMBER 94202, TYPE NO.0115-E1

201

780

lit REQUIRES SPECIAL TOOLSTO INSTALL SEE REPAIRINSTRUCTION MANUAL

o®181

2o ,

526

44


BRIGGS & STRATTON ENGINE - MODEL NUMBER 94202, TYPE NO,0115-E1

358 QASKET SET I

121 CARBUR_-'TOR KITI

1095 VALVE OVERHAUL GASKET SET I

45



KEY PART KEY PARTNO. NO. DESCRIPTION NO. NO. DESCRIPTION

1 494549 Cylinder Assembly2 293708 Bushing, Cylinde (Special

Tools Required ForInstallation)

3 299819 * Seal, Oil5 214277 Head, Cylinder7 272694 _* Gasket, Cylinder Head8 495774 Breather, Valve Chamber9 27549 _* Gasket, Valve Cover10 94621 Screw, Seres, Valve Cover

Mount.11 66578 Grommet, Breather Tube12 270833 " Gasket, Crankcase,

Standard .015"270895 * Gasket, Crankcase .005"270896 * Gasket, Crankcase .009"

13 94960 Screw, Cylinder Head15 94387 Plug, Oil Drain

(Opposite Carb Side)16 495211 Crankshaft

499047 Key, Timing Gear Retaining18 394820 Cover Assembly, Crankcase19 293708 Bushing, Crankcase20 299819 * Seal, Oil21 281658 Plug, Oil Filler22 94607 Screw, Hex22A 94862 Screw, Hex, (Used In Pos.

No. 1)23 496278 Flywheel24 222698 Key, Flywheel25 498668 Piston Assembly, Standard

498669 Piston Assembly .010"Oversize



26 498680 Ring Set, Piston, Standard498681 Ring Set, Piston .010"

Oversize498682 Ring Set, Piston .020"

Oversize498683 Ring Set, Piston .030"

Oversize27 26026 Lock, Piston Pin28 298909 Pin Assembly, Piston,

Standard298908 Pin Assembly, Piston .005"

Over29 294367 Rod Assembly, Connecting

296079 Rod Assembly, Connecting,.020" Undersize CrankpinBore

30 220670 Dipper, Connecting Rod32 94699 Screw, Connecting Rod33 296676 Valve, Exhaust (Includes

Retainer Number 93312)34 296677 Valve, Intake

35 260552 Spring, Valve37 224557 Guard, Fylwheel38 94736 Screw, Hex40 93312 Retainer, Valve Spring45 230173 Tappet, Valve46 493747 Gear, Cam51 273113 _** Gasket, Carb, Mounting53 94523 Screw, Exhaust55 499441 Housing, Rewind, Starter58 281464 Rope, Starter60 393152 Grip, Starter Rope65 94904 Screw, Starter, Housing73 225381 Screen, Rotating90 499491 Carburetor Assembly95 93499 Screw, Slotted96 223793 Valve, Throttle97 495313 Shaft and Lever, Throttle109 497230 Choke, Shaft Kit121 495606 Carburetor, Overhaul Kit124 94616 Screw, Torx_127 220352 Plug, Welch127A 223789 Plug, Welch144 499901 Pulley/Spring Assy.152 260575 Spring Throttle Ad ustment153 490501 Collar, Bell, Crank154 93527 Screw, Slotted161 492797 Base, Air Cleaner163 271935 O* Gasket, AirCleaner180 495377 Tank, Fuel181 494559 Cap, Fuel Tank190 94919 Screw, Torx_190A 94924 Screw, Torx_191 272489 Gasket, Fuel Tank

Indicates Parts Included in Gasket Set(494550)

** IndicatesParts IncludedinCarburetorOverhaul Kit (495606)

IndicatesParts Included in ValueOverhaulGasket Set (292638)

NOTE: All component dimensions given inU.S. inches 1 inch = 25.4 mm

46



KEY PART KEY PARTNO. NO. DESCRIPTION NO. NO. DESCRIPTION

200 495213 Blade, Governor201 263174 Link, Governor202 262470 Unk, Throttle209 260041 Spring, Governor211 263030 Spring, Gov. Idle216 263188 Link, Choke222 499533 Bracket, Controt257 93543 Screw, HexHead298 220859 Locknut, Muffler300 493288 Muffler, Exhaust304 499522 Housing, Blower305 94786 Screw, Seres306 224555 Shield, Cylinder307 93758 Screw, Sems, Cylinder

Shield Mnt.308 224556 Cover, Cylinder Head332 94877 Nut, Flywheel333 496914 Armature, Magneto334 94731 Screw, Armature Mounting337 802592 Plug, Spark356 497298 Wire, Ground358 495605 Gasket Set363 19203 Puller, Flywheel373 94908 Nut, Hex383 89838 Wrench, Spark Plug392 262328 Spring, Fuel Pump

Diaphragm393 225058 Screw, Carburetor394 272538 ** Diaphragm432 221377 Cap, Spring433 93265 Pin, Diaphragm434 213963 Cover, Diaphragm435 93141 Screw, Diaphragm Cover455 225502 Cup, Flywheel456 281503 Plate, Pawl Friction459 281505 Pawl, Ratchet526 94914 Screw, Hex527 223786 Clamp, Breather Tube528 491435 Filter, Air529 67838 Grommet, BreatherTube535 491435 Filter, Air536 494279 Air Cleaner Kit542 94897 Screw, Hex Head608 499706 Starter Assembly, Rewind609 265715 Spring, Choke611 231067 Line, Fuel612 391813 Tube, Pickup621 296110 Switch, Stop

621A62363463564367968068974174878085186486987O871

396847 Switch, Stop94943 Screw, Shoulder271853 Washer, Throttle Shaft, Foam66538 E|bow, Spark Plug280737 Spacer, Air Cleaner270382 Washer, Choke Shaft, Foam221839 Washer, Choke Shaft260575 Spring, Friction261533 Gear, Timing99669 Screw, Hex.225029 Anchor, Spring493880 Terminal, Ignition Cable492232 Adapter Assembly, Muffler211172 Seat, Intake Valve211291 Seat, Exhaust Valve231348 Guide, Exhaust Valve63709 Guide, Intake Valve

(See Repair Manual)Gasket, MufflerPlugFilter, AirCover, Air CleanerScrew, Slotted Hex,(Inc(. Grommet)Screw, RexSeal, Throttle ShaftSpark AttesterControl, ThrottleLabel Kit, EmissionGasket Set, Vavle Overhaul

94202-0115 Replacement Engine-- -- 495914 Replacement Shortblock

883 272203955 281227967 491588968 495872969 490073

971 94902987 398970994 398O67995 4971951036 49932910959966925O0

RPM Settings: Low: 12O0-1600High: 3500 - 3700

Indicates Parts Included in Gasket Set(494550)

** Indicates Parts Included in CarburetorOverhaul Kit (495606)

_1 IndicatesParts IncludedinValueOverhaul Gasket Set (292638)

NOTE: All component dimensions given inU.S. inches 1 inch = 25.4 mm

47

For repair of major brand appliances In your own home...no marLerwho made _, no maIer who sold it!

1-800-4-MY-H OME sM_, c_o_._j_t(1-800-469-4663)

www.sears.com

To bring in products such as vacuums, lawn equipment and electTonicsfor repair, call for the location of your nearest Sears Parts & Repair Center

1-800-488-1222 _*_cWorn_

w_flN,sears.colrn

Fortt_ereplacement parts, accessoriesand owner's mar_alsthat you need to do-it-yourself,call Sears PartsDIrectS"!

1-8 00-3 66-PART 6a_..-11p.m._-r.(1-800-366-7278) 7 daysaweek

www.mars.com I partsdlrect

To purchase or inquire al:x_ a Sears Service Agreerne_:

1'800-827-66557a.m.- 5 p,m,CST.Mort,- Sat.

Pa'apetit_icio dermare_ ad_-r_r_y paraordenarplezaso0n_ a donicilb:

1-888-6U-HOGN:I'"(1"888-784-6427)

AuCanadapoursa'viceen_:1-877-LE-FOYER TM

(1-877-533-6937)

J ., .ARS,-,omeCentrarJ

® Regk_ Tradenuark I _" Tradmrk of Sears, Roebuck and Co.O Sears. Roebuck and Co. ® Mama Regl_mde I Tu Marca de F&brlce de Seers, Roebuck and Co.

172054 Rev. 2 1.6.00 TR Printed in U.S.A.

CRAFTSMAN+ - Sears Parts Direct

Documents

Transcript of CRAFTSMAN+ - Sears Parts Direct