BCA unitrates 13 05 2011

8/6/2019 BCA unitrates 13 05 2011

1/34

ITEM DESCRIPTION UNIT 2010Q1

MEAN

2010Q2

MEAN

2010Q3

MEAN

2010Q4

MEAN

2011Q1

MEAN

I EXCAVATION

1 GENERAL EXCAVATION

1.1 Oversite Excavation

Excavate over site, commencing from ground

level, to reduce level

A average 100mm deep m2 1.94 1.95 1.93 1.94 1.94

B average 200mm deep m2 2.40 2.38 2.37 2.38 2.38

C average 300mm deep m2 3.46 3.46 3.33 3.33 3.33

D over 300mm deep m3 12.08 12.00 11.98 12.00 12.00

1.2 Pit/Trench Excavation

Excavate to form pit or trench, commencing

from reduced level

A ne 2.00m deep m3 23.73 24.03 23.97 24.17 24.33

B 2.00 - 4.00m deep m3 26.00 25.77 25.70 25.83 26.00

C 4.00 - 6.00m deep m3 29.17 29.17 29.09 27.77 27.83

D extra over for each 2.00m deep m3 6.03 6.00 6.00 6.00 6.00

1.3 Basement Excavation

Excavate to form basement, commencing from

reduced level

A ne 2.00m deep m3 16.33 16.53 16.50 16.60 16.83

B 2.00 - 4.00m deep m3 18.00 17.83 17.77 17.83 18.00

C 4.00 - 6.00m deep m3 20.87 20.87 20.80 20.83 21.00

D extra over for each 2.00m deep m3 2.53 2.53 2.53 2.57 2.60

1.4 Break Up Obstruction

Extra over excavation for breaking up

obstruction below ground level using

mechanical means

A rock m3 92.17 92.17 92.17 92.67 93.00

2 FILLING

2.1 Backfilling

Backfill around trench, column base, pile cap,

foundation, beam and pier hole

A excavated material obtained within the site m3 8.47 8.47 8.47 8.47 8.50

B earthfilling obtained from contractor's own

sourcem

3 10.23 10.23 10.23 10.23 10.27

2.2 Filling and Forming Embankments

Deposit, spread, level, compact and

consolidate in layers of 150mm thick to make

up levels

A excavated material obtained within the sitem

3 7.33 7.33 7.33 7.33 7.37

B earthfilling obtained from contractor's own

sourcem

3 10.93 10.93 10.93 10.93 10.97

Unit Rates - ExcavationLast Updated on 13/05/11

[The data will be updated on a quarterly basis]

Page 1/34

8/6/2019 BCA unitrates 13 05 2011

2/34


MEAN

2010Q2

MEAN

2010Q3

MEAN

2010Q4

MEAN

2011Q1

MEAN

2.3 Hardcore and Aggregate

Spread, level, compact, ram and consolidate

A hardcore, including blinding with sand m3 50.17 50.17 50.17 50.17 50.17

3 DISPOSAL

3.1 Excavated Material

Remove excavated material off siteA to contractor's own dumping site m

3 12.57 12.57 12.57 12.57 12.83

Page 2/34

8/6/2019 BCA unitrates 13 05 2011

3/34


MEAN

2010Q2

MEAN

2010Q3

MEAN

2010Q4

MEAN

2011Q1

MEAN

II CONCRETE WORK

1 IN-SITU CONCRETE

1.1 Lean/Mass Concrete

Lean or Mass concrete complying with BS

8110 in any location

A grade 15 m3 187.33 192.50 193.90 199.57 204.00

B grade 20 m3 196.67 202.17 203.97 210.97 212.67

1.2 Reinforced Concrete

Reinforced concrete complying with BS 8110

in any location

A grade 25 m3 123.60 126.33 126.40 132.83 138.00

B grade 30 m3 128.68 128.78 128.83 133.88 137.75

C grade 35 m3 131.65 131.45 131.23 136.63 140.50

D grade 40 m3 134.88 134.25 134.03 140.00 144.00

E grade 50 m3 138.67 140.27 139.93 146.17 152.00

F Extra over for waterproofing agent m3 44.00 44.00 44.00 44.17 44.67

2 REINFORCEMENT

2.1 Bar Reinforcement

Mild steel bar reinforcement complying with

SS 18 in any location

A 6mm diameter kg 1.53 1.59 1.54 1.56 1.56

B 10mm diameter kg 1.53 1.59 1.54 1.56 1.56

C 13mm diameter kg 1.53 1.59 1.54 1.56 1.56

High tensile steel bar reinforcement complying

with SS 2 in any location

D 10mm diameter kg 1.52 1.58 1.52 1.55 1.55

E 12/13mm diameter kg 1.52 1.58 1.52 1.55 1.55

F 16mm diameter kg 1.52 1.58 1.52 1.55 1.55

G 20mm diameter kg 1.52 1.58 1.52 1.55 1.55H 25mm diameter kg 1.52 1.58 1.52 1.55 1.55

I 28mm diameter kg 1.52 1.58 1.52 1.55 1.55

J 32mm diameter kg 1.52 1.58 1.52 1.55 1.55

K 40mm diameter kg 1.52 1.58 1.52 1.55 1.55

2.2 Fabric Reinforcement

Welded fabric reinforcement complying with

SS 32 and well lapped (measured net)

A Reference No A6 m2 6.59 6.76 6.74 6.89 6.92

B Reference No A7 m2 7.40 7.61 7.59 7.79 7.85

C Reference No A8 m2 8.77 9.01 8.96 9.12 9.12

D Reference No A9 m2 10.64 11.01 10.91 11.10 11.14

E Reference No B6 m2 9.08 9.44 9.37 9.59 9.60

F Reference No B7 m2 10.15 10.54 10.47 10.73 10.80

G Reference No B8m

2 12.27 12.73 12.63 12.94 12.94

H Reference No B9 m2 13.60 14.06 13.93 14.22 14.18

I Reference No B10 m2 14.91 15.43 15.26 15.63 15.61

J Reference No D6 m2 9.43 9.74 9.67 9.89 9.86

Unit Rates - Concrete WorkLast Updated on 13/05/11


Page 3/34

8/6/2019 BCA unitrates 13 05 2011

4/34


MEAN

2010Q2

MEAN

2010Q3

MEAN

2010Q4

MEAN

2011Q1

MEAN

2.2 Fabric Reinforcement

Welded fabric reinforcement complying with

SS 32 and well lapped (measured net)

K Reference No D8 m2 13.70 14.13 14.00 14.28 14.24

L Reference No D9 m2 18.06 18.69 18.52 18.91 18.86

3 FORMWORK

3.1 Timber Formwork

Sawn formwork to in-situ concrete including

strutting ne 3.50m high

A flat surface of suspended slab m2 30.70 30.37 30.50 31.17 31.17

B vertical surface of pilecap, ground beam, etc. m2 30.70 30.37 30.50 31.17 31.17

C vertical surface of column, walls m2 30.70 30.37 30.50 31.17 31.17

D vertical curved surface of column, wall m2 37.67 38.17 38.33 38.33 38.50

E sides and soffits of beams m2 32.20 31.87 32.00 32.00 32.00

F vertical edge for each 100mm high m 3.05 3.05 3.05 3.05 3.05

Wrought formwork to in-situ concrete including


G flat surface m2 31.05 31.53 31.65 31.65 31.65

H vertical surface m2 31.05 31.53 31.65 31.65 31.65

I curved surface m2

41.18 42.35 42.53 42.53 42.63

Extra over formwork for strutting exceeding

J each 1.50m high m2 2.00 2.03 2.03 2.03 2.03

3.2 Metal Formwork

Metal formwork to in-situ concrete including


A vertical surface m2 49.60 51.73 51.43 52.43 52.43

B vertical curved surface m2 56.73 58.97 58.63 59.30 59.30

C 0.75mm Bondek/Condeck to flat surface of

suspended slabm

2 51.63 53.80 53.50 54.17 54.17

D 1.00mm Bondek/Condeck to flat surface of

suspended slabm

2 56.42 59.20 58.87 59.53 59.53

Extra over formwork for strutting exceeding

3.50m highE each 1.50m high m

2 5.67 5.83 5.83 5.87 5.87

4 PRECAST CONCRETE

4.1 Precast Concrete Hollow Core Slab

A 265mm m2 95.82 95.82 95.82 96.47 95.33

B 340mm m2 111.37 111.37 111.37 111.93 110.33

5 EXPANSION JOINTS

5.1 Joint Fillers

Compressible non-extruding bitumen

impregnated fibreboard to joint, including all

necessary formwork

A 10mm thick m2 24.63 24.63 24.63 24.63 24.63

B 12mm thick m2 29.38 29.38 29.38 29.38 29.38

C 25mm thick m2 41.99 41.99 41.99 41.99 41.99

Page 4/34

8/6/2019 BCA unitrates 13 05 2011

5/34


MEAN

2010Q2

MEAN

2010Q3

MEAN

2010Q4

MEAN

2011Q1

MEAN

5.2 Joint Sealant

Polysulphide sealer squeezed into joint

A 25 x 15mm joint m 14.99 14.99 14.99 14.99 14.99

B 25 x 25mm joint m 21.14 21.14 21.14 21.14 21.14

5.3 Prestressing Cables

Cable stand in beams complete with

sleeves,anchors and all necessaryaccessories

A 12x12.9mm diameter kg 5.40 5.57 5.57 5.57 5.57

6 WATERPROOF MEMBRANE

6.1 Damp Proof Membrane

Waterproofing sheet laid to top,side or

underside of concrete structure

A 0.6mm thick polyethylene moisture barrier m2 5.63 5.63 5.70 5.73 5.73

B 0.8mm thick polyethylene moisture barrier m2 8.60 8.60 8.70 8.73 8.73

C approved bituminous m2 25.59 25.59 25.76 25.83 25.33

7 INTEGRATED FINISH

Power floated finish to suspended slabs

A generally m2 4.57 4.57 4.57 4.57 4.57B with Mastercron' or approved equivalent non-

metallic hardenerm

2 16.57 16.57 16.57 16.57 15.90

Page 5/34

8/6/2019 BCA unitrates 13 05 2011

6/34


MEAN

2010Q2

MEAN

2010Q3

MEAN

2010Q4

MEAN

2011Q1

MEAN

III BRICKWORK AND BLOCKWORK

1 CLAY BRICKS

1.1 Common Brickwork (Standard Size)

Common brick in cement mortar (1:4) with

mortar plasticiser

A 115mm thick wal l m2 30.13 30.88 30.88 30.88 30.88

B 230mm thick wal l m2 60.25 61.25 61.25 61.25 61.25

1.2 Facing Brickwork

First quality facing brick in cement mortar (1:4)

with plasticiser

A 115mm thick wal l m2 41.97 42.37 42.37 42.30 42.30

B 215mm thick wal l m2 85.80 86.63 86.63 86.13 86.13

2 CONCRETE BLOCKS

2.1 Hollow Blockwork

Hollow concrete block in cement mortar (1:4)

A 390x190x90mm thick wall m2 25.33 25.60 25.60 25.43 25.67

B 390x190x190mm thick wall m2 48.80 49.27 49.27 48.97 49.17

Unit Rates - Brickwork and BlockworkLast Updated on 13/05/11


Page 6/34

8/6/2019 BCA unitrates 13 05 2011

7/34


MEAN

2010Q2

MEAN

2010Q3

MEAN

2010Q4

MEAN

2011Q1

MEAN

IV ROOFING

1 TILE ROOFING

1.1 Clay Roof Tiles

`GR 13' French clay interlocking roof tiles with

galvanised nails on every 4th course

A generally m2 57.26 57.26 57.26 57.26 57.26

Extra over `GR 13' French clay for roof

accessories

B ridge or hip tile m 42.12 42.12 42.12 42.12 42.12

"Roman GR 13" or other equal roof tiles fixed

to batten with galvanised nails at

approximately 400mm centres

C generally m2 47.78 47.78 47.78 47.78 47.78

Extra over GR13 for roof accessory

D ridge or hip tile m 39.25 39.25 39.25 39.25 39.25

TBF Romane tile fixed to battens (measured

separately) with galvanised nails at

approximately 400mm centres

E generally m 55.99 55.99 55.99 55.99 55.99

Extra over TBF Romane tile' for roof

necessary

F ridge or hip tile m 42.78 42.78 42.78 42.78 42.78

1.2 Concrete Roof Tiles

Redland `51' or Pelangi interlocking concrete

roofing tile complying with SS310 and SS

CP43 fixed to battens (measured separately)

with galvanised nails at every other courseA generally m

2 21.60 21.60 21.60 21.60 21.60

Extra over for Redland `51' or Pelangi roof

accessories

B ridge tile m 13.84 13.84 13.84 13.84 13.84

Monier interlocking concrete roofing tile

complying with SS310 and SS CP43 fixed to

battens (measured separately) with galvanised

nails at every other course

C generally m2 35.07 35.07 35.07 35.07 35.07

Extra over Monier roof accessory

D ridge tile m 21.10 21.10 21.10 21.10 21.10

Unit Rates - RoofingLast Updated on 13/05/11


Page 7/34

8/6/2019 BCA unitrates 13 05 2011

8/34


MEAN

2010Q2

MEAN

2010Q3

MEAN

2010Q4

MEAN

2011Q1

MEAN

2 BUILT-UP ROOFING

2.1 Insitu Finishes

`Vermiculite' lightweight screed wood floated

finish laid to falls on concrete to receive

waterproof membrane

A 25mm m2 15.81 15.81 15.81 15.81 15.81

B 50mm m2 26.29 26.29 26.29 26.29 26.29

C add or deduct for each 10mm thickness m2 5.78 5.78 5.78 5.78 5.78

`Ais-Texsa' lightweight concrete insulating

underbeds to flat roof to falls

D 75mm m2 16.04 16.04 16.04 16.04 16.04

E add or deduct for each 10mm thickness m2 4.38 4.38 4.38 4.38 4.38

Cement and sand (1:3) screed with Sika'

waterproofing additive

F 25mm m2 15.43 15.60 16.00 16.17 16.50

G 50mm m2 24.63 24.90 25.50 25.50 25.87

H add or deduct for each 10mm thickness m2 5.20 5.20 5.20 5.20 5.27

Cement and sand (1:3) screed

I 25mm m2 13.70 14.08 14.38 14.38 14.50

J 50mm m2 17.17 17.60 18.17 18.17 18.33

K add or deduct for each 10mm thickness m2 3.78 3.78 3.78 3.78 3.82

2.2 Waterproofing Membranes

Roof waterproofing membrane system on

screed (measured separately)

A Nural ite sheet m2 53.67 53.67 53.67 53.67 53.67

3mm Mortar Plas waterproofing membrane

with minimum 75mm laps

B to f lat surface m2 21.67 21.67 21.67 21.67 21.67

C to vertical surface m2 22.69 22.69 22.69 22.69 22.69

Bituthene 3000 waterproofing membrane

D to f lat surface m2 26.80 26.80 26.80 26.80 26.80

E to vertical surface m2 26.80 26.80 26.80 26.80 26.80

Hypalon waterproofing membrane

F to f lat surface m2 30.73 30.73 30.73 30.73 30.73

G to vertical surface m2 30.73 30.73 30.73 30.73 30.73

`Apex' waterproofing membrane

H to f lat surface m2 26.54 26.54 26.54 26.54 26.54

I to vertical surface m2 26.54 26.54 26.54 26.54 26.54

Carboeol waterproof membrane

J to flat surface m2 27.69 27.69 27.69 27.69 27.69

K to vertical surface m2 29.97 29.97 29.97 29.97 29.97

2mm `Texsaplas' exposed synthetic

waterproofing membrane

L gutter m2 20.98 20.98 20.98 20.98 20.98

Page 8/34

8/6/2019 BCA unitrates 13 05 2011

9/34


MEAN

2010Q2

MEAN

2010Q3

MEAN

2010Q4

MEAN

2011Q1

MEAN

2.2 Waterproofing Membranes

0.90mm Uniroof' waterproofing membrane

M flat surface m2 29.41 29.41 29.41 29.41 29.41

N vertical surface m2 30.57 30.57 30.57 30.57 30.57

2.3 Panel Roofing

Waterproofed cement and sand (1:3) screed

A 25mm thick (average) m2 16.46 16.66 17.13 17.13 17.16

B 50mm thick (average) m2 29.90 30.27 31.10 31.10 31.10

Precast concrete panel grade 20 roof slab

C 600 x 600 x 50mm m2 31.93 32.26 32.26 32.93 32.93

3 PROFILED SHEET ROOFING OR CLADDING

3.1 Steel Deckings

Galvanised steel roof or wall cladding with

zincalume coating and colorbond finish on one

side, fixed to steel or timber framing

(measured separately) with fixing clips,bolts

and nails

A 0.47mm thick Stramit `Multideck Hi-Ten' sheet m2 33.00 33.00 33.00 33.00 33.00

B 0.48mm thick BlueScope Lysaght Trimdek Hi-

Ten' sheetm

2 35.47 35.47 35.47 35.47 35.47

C 0.53mm thick Stramit Speed Deck Hi-Ten'

sheetm

2 37.93 37.93 37.93 37.93 37.93

D 0.53mm thick BlueScope Lysaght Colorbond

XRW Kliplok Hi-Ten roofing sheetm

2 41.57 41.57 41.57 41.57 41.57

Galvanised steel roof or wall cladding with

zincalume coating and colorbond finish on one

side, fixed to steel or timber framing

(measured separately) with fixing clips,bolts

and nails

E 0.47mm thick BlueScope Lysaght Colorbond

XRW Crimp Curved Trimdek Hi-Ten roofing

sheet

m2 45.63 45.63 45.63 45.63 45.63

F 0.61mm thick Stramit `C-Clad' sheet m2 44.90 44.90 44.90 44.90 44.90

G 0.65mm thick Stramit Sped Deck Hi-Ten'sheet

m2 50.57 50.57 50.57 50.57 50.57

4 RAINWATER GOODS

4.1 Flashings/Cappings

0.61mm thick galvanised steel standard rain-

water goods with zincalume coating and

colorbond finish including fixing clips, bolts and

nails

A girth f lashing m2 34.50 34.50 34.50 34.50 35.20

B girth capping m2 44.70 44.70 44.70 44.70 45.23

1.0mm thick Zincalume (unpainted) box gutter

including fixing accessories

C girth f lashingm

2 49.70 49.70 49.70 49.70 49.73

D girth capping m2 52.81 52.81 52.81 52.81 52.81

Page 9/34

8/6/2019 BCA unitrates 13 05 2011

10/34


MEAN

2010Q2

MEAN

2010Q3

MEAN

2010Q4

MEAN

2011Q1

MEAN

4.1 Flashings/Cappings

1mm thick natural anodised aluminium

including fixing clips, bolts and nails

E girth f lashing m2 48.77 48.77 48.77 48.77 47.37

F girth capping m2 57.03 57.03 57.03 57.03 55.66

2mm thick natural anodised aluminium

including fixing clips, bolts and nails

G girth f lashing m2 56.39 56.39 56.39 56.39 56.82

H girth capping m2 56.99 56.99 56.99 56.99 57.66

Stainless steel in No 4 brush finish including

fixing chips, bolts and nails

I girth flashing m2 67.09 67.09 67.09 67.09 67.09

4.2 Gutters

1.2mm thick galvanised steel open box gutter

with zincalume coating and colorbond finish

including brackets, fixing clips, bolts, nails and

laying to falls

A gutter m2 95.40 95.40 95.40 95.40 95.40

4.3 UPVC Downpipes

Unplasticied polyvinyl chloride rainwater

downpipe including solvent welded joints and

jointing to sumps and drains

A 75mm diameter m 35.73 36.37 34.87 35.33 36.00

B 100mm diameter m 40.63 41.67 40.00 40.50 41.67

C 150mm diameter m 54.10 55.07 53.43 54.00 55.00

D 250mm diameter m 66.33 67.57 64.67 64.67 65.33

5 SUNDRIES

5.1 Insulation

Insulation material to roof

A 50mm thick fibreglass insulation, density 16

kg/m3m

2 7.00 7.00 7.00 7.00 7.33

B 25mm thick m2 5.67 5.67 5.67 5.67 5.67

Insulation material to roof

C ACI Sisalation 450 double-sided, double

reinforced aluminum foil insulation paper with

150mm laps

m2 5.08 5.08 5.08 5.08 5.08

D 50mm Roofmate' or equivalent extruded

polystyrene insulation boardm

2 18.67 18.67 18.67 18.67 18.67

5.2 Wire Mesh

Wire mesh to roof space including dressing

over purlins (measured net)

A BRC Reference No 3315 (75 x 75 x 1.5mm

diameter)m

2 3.76 3.76 3.76 3.76 3.86

5.3 Purlin

A Lysaght Z20020 purlin m 25.33 25.33 25.33 25.33 25.33

B Lysaght C20025 purlin m 30.70 30.70 30.70 30.70 30.70

Page 10/34

8/6/2019 BCA unitrates 13 05 2011

11/34


MEAN

2010Q2

MEAN

2010Q3

MEAN

2010Q4

MEAN

2011Q1

MEAN

V CARPENTRY AND JOINERY

1 CARCASSING

1.1 Structural Timber

Sawn timber in carpenter's works

A kapur m3 1910.00 1910.00 1910.00 1910.00 1910.00

B balau m3 2128.33 2128.33 2128.33 2128.33 2128.33

C kempas m3 1453.33 1453.33 1453.33 1453.33 1453.33

D chengal m3 2886.83 2886.83 2886.83 2886.83 2886.83

1.2 Timber Preservation

Extra over structural timber for pressure

impregnation with a suitable wood

preservative to an average dry salt retention of

5.6kg/m3 and complying with SS 72 and

treated in accordance with SS CP 1

A generally m3 74.67 74.67 74.67 74.67 74.67

2 FRAMING

2.1 Mouldings

Bead, picture rail, architrave, fillet and cornice

and the like not exceeding 500mm2 in

sectional area including gluing and nailing

A teak m 12.55 12.55 12.55 12.55 12.55

B chengal m 8.41 8.41 8.41 8.41 8.41

C balau m 9.47 9.47 9.47 9.47 9.47

2.2 Joinery Framing

Wrought kapur in frame and the like

A per 1000mm2 sectional area m 4.78 4.78 4.78 4.78 4.78

Wrought tanalised chengal in frame and thelike

B per 1000mm2 sectional in area m 21.04 21.04 21.04 21.04 21.04

Wrought teak in frame and the like

C per 1000mm2 sectional in area m 31.55 31.55 31.55 31.55 31.55

Wrought oak in frame and the like

D per 1000mm2 sectional in area m 39.87 39.87 39.87 39.87 39.87

2.3 Handrails

Wrought oak in handrails and the like

A per 1000mm2 sectional area m 69.48 69.48 69.48 69.48 69.48

Wrought kapur in handrails and the like

B per 1000mm2 sectional area m 26.38 26.38 26.38 26.38 26.38

Wrought Balau in handrails and the like

C per 1000mm2 sectional area m 33.66 33.66 33.66 33.66 33.66

Unit Rates - Carpentry and JoineryLast Updated on 13/05/11


Page 11/34

8/6/2019 BCA unitrates 13 05 2011

12/34


MEAN

2010Q2

MEAN

2010Q3

MEAN

2010Q4

MEAN

2011Q1

MEAN

2.4 Stud Partition Framing

Sawn kapur framing fixed at 600mm centres

bothways

A 50 x 50mm cross-section m2 25.06 25.06 25.06 25.06 25.06

B 50 x 75mm cross-section m2 36.23 36.23 36.23 36.23 36.23

3 LININGS

3.1 Calcium Silicate Boards

Calcium silicate board reinforced with selected

fibres and fillers (Class 0) including pointing

A 6mm thick m2 21.56 21.56 21.56 21.78 21.78

B 9mm thick m2 30.42 30.42 30.42 30.73 30.73

C 12mm thick m2 33.71 33.71 33.71 33.75 33.75

3.2 Cement Building Boards

Cement building board including pointing

A 6mm thick m2 18.85 18.85 18.85 18.85 18.85

B 12mm thick m2 26.24 26.24 26.24 26.24 26.24

3.3 Gypsum Boards

Bare finish gypsum board including pointing

A 10mm thick m2 16.92 16.92 16.92 16.92 17.39

B 13mm thick m2 20.85 20.85 20.85 20.85 21.45

3.4 Plywoods

Non-waterproofed plywood complying with

SS1

A 6mm thick m2 16.32 16.32 16.32 16.32 16.33

B 12mm thick m2 21.17 21.17 21.17 21.17 21.18

C 18mm thick m2 26.48 26.48 26.48 26.48 26.51

D 25mm thick m2 37.77 37.77 37.77 37.77 37.84

Waterproofed plywood type WBP

E 6mm thick m2 19.78 19.78 19.78 19.78 19.79

F 12mm thick m2 26.18 26.18 26.18 26.18 26.18

G 18mm thick m2 33.39 33.39 33.39 33.39 33.41

H 25mm thick m2 37.55 37.55 37.55 37.55 37.66

3.5 Laminated Plastics

Laminated plastic sheet to BS 3796 including

compatible adhesive

A 0.8mm thick Formica m2 24.08 24.08 24.08 24.08 24.08

B 0.8mm thick Print m2 21.17 21.17 21.17 21.17 21.17

C 1.0mm thick Formica m2 28.16 28.16 28.16 28.16 28.16

Laminated plastic sheet to BS 3796 including

compatible adhesive

D 1.0mm thick Print m2 23.12 23.12 23.12 23.12 23.12

E 1.2mm thick Print m2 26.23 26.23 26.23 26.23 26.23

F 1.3mm thick Print m2 26.08 26.08 26.08 26.08 26.08

G 1.3mm thick Formica m2 31.28 31.28 31.28 31.28 31.28

Page 12/34

8/6/2019 BCA unitrates 13 05 2011

13/34


MEAN

2010Q2

MEAN

2010Q3

MEAN

2010Q4

MEAN

2011Q1

MEAN

4 WALL INSULATION

4.1 Fibreglass

Supply and fix fibreglass

A 50mm thick, 48 kg/m3 m2 22.70 22.70 22.70 22.70 22.70

B 75mm thick, 48 kg/m3 m2 28.38 28.38 28.38 28.38 28.38

4.2 Mineral Wool

Supply and fix mineral wool

A 25mm thick, 48 kg/m3 m2 12.75 12.75 12.75 12.75 12.75

B 50mm thick, 48 kg/m3 m2 17.38 17.38 17.38 17.38 17.38

C 25mm thick, 80 kg/m3 m2 14.75 14.75 14.75 14.75 14.75

5 PANELLING

5.1 Timber Panelling

100mm wide tongued and grooved wrought

boarding fixed to battens (measured

separately)

A 13mm thick ramin m2 55.39 55.39 55.39 55.39 55.50

B 19mm thick ramin m2 72.86 72.86 72.86 72.86 72.94

C 13mm thick chengal m2 46.31 46.31 46.31 46.31 46.52

D 19mm thick chengal m2 52.39 52.39 52.39 52.39 52.46E 25mm thick chengal m

2 113.16 113.16 113.16 113.16 113.83

5.2 Woodwool Slab Wall Panelling

Supply and fix woodwool slab to wall

A 50mm thick m2 17.83 17.83 17.83 17.83 17.83

5.3 Glasal Panels

`Glasal' fully compressed autoclaved fibre

cement sheet panel fixed to timber frame

A 45mm thick panel fixed to timber frame and

bendm

2 120.92 120.92 120.92 120.92 120.92

6 FLOORING

6.1 Floor Boards

100mm wide wrought plain edge floor board

fixed to bearers (measured separately)

A 19mm thick teak m2 86.36 86.36 86.36 86.36 86.36

B 25mm thick teak m2 103.99 103.99 103.99 103.99 103.99

C 19mm thick chengal m2 52.15 52.15 52.15 52.15 52.15

D 25mm thick chengal m2 62.80 62.80 62.80 62.80 62.80

100mm wide wrought tongued and grooved

floor board fixed to bearers (measured

separately)

E 19mm thick teak m2 107.32 107.65 107.65 107.65 107.65

F 25mm thick teak m2 127.98 128.65 128.65 128.65 128.65

G 19mm thick chengal m2 74.17 74.50 74.50 74.50 74.50

H 25mm thick chengal m2 85.38 85.72 85.72 85.72 85.72

I 20mm thick oak m2 150.33 150.33 150.33 150.33 150.33

Page 13/34

8/6/2019 BCA unitrates 13 05 2011

14/34


MEAN

2010Q2

MEAN

2010Q3

MEAN

2010Q4

MEAN

2011Q1

MEAN

6.2 Block/Parquet Flooring

Teak parquet floor laid to herring-bone pattern,

bedded and jointed with and including one

coat of bituminous emulsion

A 12mm thick m2 43.25 43.25 43.25 43.82 43.82

B 20mm thick m2 54.63 54.63 54.63 56.13 56.13

Ramin parquet floor in mosaic pattern

C 8mm thick m2 99.60 99.60 99.60 99.60 99.60

7 DOORS

7.1 Kapur Flush Doors

Solid core flush door complying with BS 459

comprising hardwood lipping around 16mm

wide vertical core strips glued and well

cramped together and covered on both sides

with 6mm thick plywood

A 45mm thick m2 243.27 243.27 248.17 248.17 250.00

B 50mm thick m2 260.97 260.97 266.23 266.23 268.33

Skeleton framed flush door complying with BS

459 comprising hardwood lipping all round

stiles and rails covered on both sides with

6mm thick plywood

C 38mm thick m2 106.00 106.00 109.67 109.67 110.00

D 45mm thick m2 120.00 120.00 124.00 124.00 124.33

E 50mm thick m2 123.00 123.00 127.00 127.00 128.00

Hollow core flush door complying with BS 459

comprising skeleton framing, hardwood lipping

all round and covered on both sides with 6mm

thick plywood

F 38mm thick m2 178.33 176.67 180.67 180.67 183.33

G 45mm thick m2 198.20 197.67 202.17 202.17 204.33

7.2 Kapur Panelled Doors

Panelled door complying with BS 459 in 3

panels comprising stiles and rails framed

around 20mm thick plywood

A 38mm thick m2 186.29 186.29 186.29 186.29 186.29

B 45mm thick m2 220.72 220.72 220.72 220.72 220.72

Labour only to form observation panels of any

size in doors

C generally No 31.68 31.68 31.68 31.68 31.76

7.3 Timber Fire Door

1/2 hour rated fire door complying with SS 332

complete with fire proofed cylinder lockset,

stainless steel ball bearing hinges, flush bolt,

door closer and frame

A 900x2100x45mm thick, double leaf No 694.96 694.86 697.19 697.19 697.19

B 900x2100x45mm thick, single leaf No 717.28 717.17 719.83 719.83 719.83

C 1200x2100x45mm thick, single unequal leaf No 907.59 907.47 910.47 910.47 910.47

D 1200x2100x45mm thick, double unequal leaf No 969.81 969.67 972.87 972.87 972.34

E 1800x2100x45mm thick, double leaf No 1438.27 1438.07 1442.73 1442.73 1441.40

Page 14/34

8/6/2019 BCA unitrates 13 05 2011

15/34


MEAN

2010Q2

MEAN

2010Q3

MEAN

2010Q4

MEAN

2011Q1

MEAN

7.3 Timber Fire Door

1 hour rated fire door complying with SS 332




F 900x2100x45mm thick, single leaf No 826.21 828.90 828.90 828.90 828.90

G 1200x2100x45mm thick, double unequal leaf No 1303.47 1307.90 1307.90 1307.90 1307.90

2 hour rated fire door complying with SS 332




H 900x2100x45mm thick, single leaf No 1438.50 1438.50 1438.50 1438.50 1438.57

8 PARTITIONS

Drywall partition covered both sides with 2

layers of 13mm gypsum plasterboards with

fibreglass/rockwood insulation including steel

studs,fixing and jointing accessories

A wall m2 61.35 63.77 63.77 63.77 62.50

150mm one hour fire rated gypsum drywall

partition covered both sides with 2 layers

13mm gypsum plasterboard including steelstuds fixing and jointing accessories

B wall m2 80.90 81.63 81.63 81.83 81.83

214mm two hour rated gypsum drywall

partition covered both sides with 3 layers

19mm,gypsum plasterboard including steel

studs, fixing and jointing accessory

C wall m2 149.57 150.97 150.97 151.07 151.07

Page 15/34

8/6/2019 BCA unitrates 13 05 2011

16/34


MEAN

2010Q2

MEAN

2010Q3

MEAN

2010Q4

MEAN

2011Q1

MEAN

VI STRUCTURAL STEELWORK & METAL WORK

1 STRUCTURAL STEELWORK

1.1 Mild Steel Members

Mild steel member complying with BS 4360

grade 55 in welded or bolted construction

A universal column kg 4.96 5.20 5.22 5.28 5.30

B universal beam kg 4.96 5.20 5.22 5.28 5.30

C connection plates kg 5.09 5.33 5.33 5.38 5.37

D composite beam kg 4.96 5.20 5.22 5.28 5.30


Grade 50 in welded or bolted construction

E universal column kg 5.03 5.27 5.27 5.33 5.37

F universal beam kg 5.03 5.27 5.27 5.33 5.37

G universal curved beam kg 5.32 5.60 5.60 5.67 5.70

H connection plate kg 5.26 5.53 5.53 5.60 5.63I roof truss kg 5.10 5.37 5.37 5.43 5.47


grade 43 in stanchion, beam, girder, roof truss,

purlin, cleat and bracket

J solid section kg 5.03 5.23 5.23 5.30 5.33

K hollow section kg 5.10 5.30 5.30 5.37 5.40

2 METAL WORK

2.1 Mild Steel Members

A hollow section, flat, rod, angle and channel

complying with BS 4360 Grade 43C

kg 5.08 5.33 5.37 5.37 5.37

B 50mm diameter tubular rail complying withSS17; light duty

m 51.83 52.97 53.63 53.63 53.63

C 38mm diameter tubular baluster/balustrade

complying with SS 17; light duty

m 43.00 43.93 44.27 44.27 44.27

2.2 Aluminium Members

Aluminium members complying with BS 1474

A 50mm diameter, 1.5mm thick natural anodised

tubular rail

m 46.33 46.33 47.00 47.00 47.00

B 38mm diameter, 1.5mm thick natural anodised

tubular baluster/balustrade

m 37.17 37.17 37.83 37.83 37.83

Unit Rates - Structural Steelwork & Metal WorkLast Updated on 13/05/11


Page 16/34

8/6/2019 BCA unitrates 13 05 2011

17/34

8/6/2019 BCA unitrates 13 05 2011

18/34


MEAN

2010Q2

MEAN

2010Q3

MEAN

2010Q4

MEAN

2011Q1

MEAN

4.1 Casements and Sashes

Natural anodised aluminium section frames in

single light, complete with ironmongery, fixing

straps, vinyl weather strips including building-

in and pointing frame (glass measured

separately)

E side-hinged window and casement frames m2 213.83 213.83 214.90 214.90 215.67

F top-hung window frame and sash m

2

214.20 214.20 215.27 215.27 216.03G sliding window frame and sash m

2 199.96 199.96 200.90 200.90 201.50

H fixed window frame m2 167.19 167.19 167.73 167.73 168.23

4.2 Louvre Window Frames

Dark coloured anodised aluminium adjustable

louvre window frame complying with SS 212

including 6mm thick clips

A set of frame with single control m 41.50 41.50 41.50 41.50 41.50

B set of frame with dual control m 43.90 43.90 43.90 43.90 43.90

4.3 Shopfront

Supply and fix aluminium shopfront frame

complete with 10mm thick tinted float glass

and fixing accessories, ironmongeries

A generally m2 330.53 330.53 330.53 330.53 330.53

Supply and fix aluminium shopfront frame

complete with 12mm thick tempered tinted

glass and fixing accessories

B generally m2 382.50 382.50 382.50 382.50 382.50

4.4 Cladding

Supply and fix dark coloured anodised

aluminium frame complete with all necessary

fixing accessories

A 670mm overall girth as cladding to concrete

postm

2 267.50 267.50 267.50 267.50 268.97

B 390mm overall girth as sill m2 276.08 276.08 276.08 276.08 277.73

C 560mm overall girth as blind pelmet m2 276.08 276.08 276.08 276.08 277.73

5 DOORS

5.1 Door Frames

Welded pressed galvanised steel rebated door

frame to suit 110mm wall complying with BS

1245

A 1.2mm thick m 37.37 37.37 37.37 37.37 37.40

Page 18/34

8/6/2019 BCA unitrates 13 05 2011

19/34


MEAN

2010Q2

MEAN

2010Q3

MEAN

2010Q4

MEAN

2011Q1

MEAN

5.2 Roller Shutter

Manually operated roller shutter constructed of

zincalume and colorbond finished sheet steel

panel curtain permanently lock-seamed and

wrapped around drum assembly with extruded

aluminium section, bottom rail including PVC

weather seal and ironmongery

A generallym

2 316.67 318.37 318.37 318.37 320.00

Motor operated roller shutter constructed of

zincalume and colorbond finished sheet steel

panel curtain permanently lock-seamed and

wrapped around drum assembly with extruded

aluminium section, bottom rail including PVC

weather seal and ironmongery

B generally m2 563.33 566.67 566.67 566.67 560.00

5.3 Metal Fire Doors

1/2 hour rated steel fire door complying with

SS 332 complete with fire proofed cylinder

lockset, stainless steel ball bearing hinges,

flush bolt, door closer and frame

A 1100 x 2150mm high No 1,078.77 1,111.53 1,111.53 1,111.53 1,111.53B 1100 x 2150mm high complete with approved No 1,170.48 1,204.33 1,204.33 1,204.33 1,204.33

6.35mm thick clear glass vision panel 600 x

125mm high

1 hour rated steel fire door complying with SS

332 complete with fire proofed cylinder

lockset, stainless steel ball bearing

hinges,flush bolt,door closer and frame

C 1200 x 2100 x 47mm thick, single leaf No 1,253.31 1,228.40 1,228.40 1,228.40 1,228.40

D 2400 x 2100 x 47mm thick, double leaf No 2,583.83 2,532.40 2,532.40 2,532.40 2,532.40

2 hour rated steel fire door complying with SS

332 complete with fire proofed cylinder

lockset, stainless steel ball bearing hinges,

flush bolt, door closer and frame

E 1200 x 2100 x 48mm thick, single leaf No 1,353.71 1,400.40 1,400.40 1,400.40 1,400.40

F 1800 x 2650 x 48mm thick, double leaf No 2,670.37 2,758.77 2,758.77 2,758.77 2,758.77

G 2400 x 2100 x 48mm thick, double leaf No 2,825.08 2,918.50 2,918.50 2,918.50 2,918.50

4 hour rated metal fire and acoustic doors

H 900 x 2090mm high, single leaf No 2,857.01 2,950.50 2,950.50 2,950.50 2,950.50

I 1800 x 2400mm high, double leaf No 6,486.47 6,691.40 6,691.40 6,691.40 6,691.40

Page 19/34

8/6/2019 BCA unitrates 13 05 2011

20/34


MEAN

2010Q2

MEAN

2010Q3

MEAN

2010Q4

MEAN

2011Q1

MEAN

6 BALUSTRADES AND HANDRAILS

6.1 Stainless Steel

900mm stainless steel glass balustrades

comprising 75mm diameter tubular top rail,

20mm vertical flat bars and 12mm thick

etched pattern tempered glass panels fixed to

balusters with stainless buttons with bottom

ends of baluster cast into concrete

A horizontal balustrades m 856.00 860.00 856.00 856.00 856.00

B raking balustrades m 927.33 931.73 927.30 927.30 927.30

1200mm high balustrades comprising 100mm

diameter tubular stainless steel hairline finish

top rail and 12mm thick clear tempered glass

infill panel complete with all necessary fixings

and jointings

C horizontal balustrades m 1,316.00 1,322.10 1,316.00 1,316.00 1,316.00

D raking balustrades m 1,397.17 1,403.63 1,397.17 1,397.17 1,397.17


tubular satin finish stainless steel top rail with

20x40mm vertical frames welded to top rail at

1000 centres with 12mm thick tempered glassinfill panels complete with all necessary fixings

and jointings

E horzontal balustrades m 1,113.17 1,118.37 1,113.17 1,113.17 1,113.17

F raking balustrades m 1,171.33 1,176.80 1,171.33 1,171.33 1,171.33

6.2 Polished Stainless Steel


diameter, two 20mm tubular intermediate and

bottom rails with 32mm tubular balusters fixed

with 100x100x6mm bearing plates at 800mm

centres

A raking balustrades m 325.47 335.55 325.47 325.47 325.47


diameter tubular handrails and bottom railsboth ends fixed with 150x150x6mm bearing

plates with and including two 13mm diameter

bolts with masonry anchors,38x4mm flat L

shaped grid rails with 50x50x4mm triangular

stiffener plates,50x6mm flat balusters at

1000mm centres fixed with 150x150x6mm

bearing plates with and including two 13mm

diameter bolts with masonry anchors fixed to

concrete kerbs

B horizontal balustrades m 471.67 485.75 471.67 471.67 471.67

Page 20/34

8/6/2019 BCA unitrates 13 05 2011

21/34


MEAN

2010Q2

MEAN

2010Q3

MEAN

2010Q4

MEAN

2011Q1

MEAN

6.3 Mild Steel

900mm high mild steel balustrades comprising

50mm diameter tubular handrails infilled with

20 x 6 thick top and bottom flat bars welded to

20mm diameter vertical sections including 20

x 6mm bar baluster

A raking balustrades m 134.67 135.33 135.33 135.33 135.33

B horizontal balustrades m 131.00 131.67 131.67 131.67 131.67

1000mm high mild steel balustrades

comprising 50mm diameter tubular handrails

infilled with 20 x 6 thick top and bottom flat

bars welded to 20mm diameter vertical

sections including 20 x 6mm bar baluster

C raking balustrades m 123.33 124.00 124.00 124.00 124.00

D horizontal balustrades m 120.33 121.00 121.00 121.00 121.00

1000mm high mild steel balustrades

comprising 38x4mm flat core and bottom rails,

38x4mm flat L shaped grid rails with

50x50x4mm triangular stiffener plates,

50x6mm flat balusters at 1000mm centres

E horizontal balustrades m 116.74 116.74 116.74 116.74 116.74

7 PROPRIETORY DEMOUNTABLE PARTITIONS

7.1 Proprietory Toilet Cubicle

Supply & fix `Domo ZF' Series partition

including fixing accessories

A single cubicle 1800mm wide No 1,913.95 1,913.95 1,913.95 1,913.95 1,913.95

B range of two cubicles overall size No 3,212.70 3,212.70 3,212.70 3,212.70 3,212.70

C range of three cubicles overall size No 4,037.80 4,037.80 4,037.80 4,037.80 4,037.80

D range of four cubicles overall size No 5,012.97 5,012.97 5,012.97 5,012.97 5,012.97

E range of f ive cubicles overall size No 6,703.98 6,703.98 6,703.98 6,703.98 6,703.98

`Moflex Carey' 10mm thick phenolic toilet

partition/cubicle in selected colour complete

with accessories

F generally m2 251.78 251.78 251.78 251.78 251.78

7.2 Proprietory Partition

`Huppe' Variplan system sliding and folding

partition of double shell construction

comprising laminated 13mm three-ply quality

chipboard with individual lever spring mounted

by plastic coated ball bearing rollers on

aluminium ceiling track supported on steel

trusses, with vertical magnetic strips at

meeting stile including all necessary framing

and ironmongery

A 8800x3600mm No 32,654.40 32,654.40 32,654.40 32,654.40 32,654.40

Page 21/34

8/6/2019 BCA unitrates 13 05 2011

22/34


MEAN

2010Q2

MEAN

2010Q3

MEAN

2010Q4

MEAN

2011Q1

MEAN

7.2 Proprietory Partition

`Huppe' Variflex 100U mechanically operated

wall system of steel and aluminium cavity

frames including all necessary framing and

ironmongery

B 8800x3600mm No 39,162.43 38,533.95 39,162.43 39,162.43 39,162.43

Styroplast partitions including all necessarystop ends, angles and intersections

C 50mm part it ion m2 56.13 56.13 56.13 56.13 56.13

8 SUNDRY

8.1 Surface Treatment

Hot dip galvanising complying with SS 117 to

structural steelwork

A generally m2 5.61 5.61 5.61 5.61 5.62

Page 22/34

8/6/2019 BCA unitrates 13 05 2011

23/34


MEAN

2010Q2

MEAN

2010Q3

MEAN

2010Q4

MEAN

2011Q1

MEAN

VII WALL AND CEILING FINISHES

1 IN-SITU FINISHES

1.1 Smooth Finished Plaster

Cement and sand (1:4) plaster mixed with

mortar plasticiser to concrete or brick surface

including trowelling smooth

A 6mm thick m2 10.67 10.83 11.73 11.73 11.73

B 13mm thick m2 13.75 14.43 15.38 15.38 15.38

C 20mm thick m2 17.08 17.78 18.95 18.95 18.95

1.2 Screed Backing

Cement and sand (1:3) screeded backing to

concrete or brick surface to receive tiling

A 13mm thick m2 12.20 12.83 13.63 13.63 13.70

B 20mm thick m2 14.85 15.50 16.50 16.55 16.63

1.3 Aggregate Plaster

Granite aggregate plaster consisting of cement

and granite chippings (1:2) with mortar

plasticiser to concrete or brick surface

including scrubbing to produce exposed

A 20mm thick m2 25.50 25.50 26.47 26.67 26.67

B 25mm thick m2 26.00 26.00 26.93 27.00 27.00

2 TILE FINISHES

2.1 Labour

Supply labour and mortar for laying

homogenous tiles to wall including pointing

with coloured cement

A generally m2

26.63 27.63 28.13 28.13 28.63

Supply labour and compatible adhesive for

laying layng tiles to wall including pointing with

coloured cement

B generally m2 31.20 32.13 32.63 32.63 32.88

3 STONE FINISHES

3.1 Labour

Supply labour and mortar for laying granite

slabs including pointing with coloured cement

A generally m2 66.38 66.38 67.63 67.63 67.63

Supply labour and mortar for laying marble

slabs includng pointing with coloured cement

B generally m2 66.88 66.88 68.13 68.13 68.13

Unit Rates - Wall and Ceiling FinishesLast Updated on 13/05/11


Page 23/34

8/6/2019 BCA unitrates 13 05 2011

24/34


MEAN

2010Q2

MEAN

2010Q3

MEAN

2010Q4

MEAN

2011Q1

MEAN

4 SHEET FINISHES

4.1 Labour


fixing decorative fabric or vinyl paper to wall

including cutting border strips, corners and

motifs to profile

A generally m2 4.30 4.30 4.30 4.30 4.33

5 SUSPENDED CEILINGS

5.1 Metal Framed Ceilings (Exposed Grid)

Exposed grid type suspended ceiling

comprising galvanised steel suspension tees

with aluminium flanged cappings arranged in

grid including 6mm diameter steel rod

hangers, clips and rivetting to all ends of grids

along the boundaries

A 16mm thick Armstrong Minaboard Tegular'

mineral fibre boardm

2 29.51 29.32 29.32 29.33 29.33

B 19mm thick Armstrong`Second Look Cortega'

acoustical mineral fibre boardm

2 31.37 31.05 31.05 31.50 31.50

C 6mm thick calcium silicate board m2 31.21 31.22 31.22 31.22 31.00

D 12mm thick calcium silicate board m2

37.31 37.32 37.32 37.32 37.00E 6mm thick cement building board m

2 29.29 29.28 29.28 29.28 29.28

F 12mm thick cement building board m2 41.33 41.33 41.33 41.33 41.33

G 10mm thick fibrous gypsum board m2 29.81 29.63 29.63 29.63 29.83

H 16mm thick fibrous gypsum board m2 36.78 36.55 36.55 36.55 36.67

I 8mm thick plain plasterglass board m2 36.84 36.83 36.83 36.83 36.83

J 16mm thick Aflco randomed fissured

fibreglass ceiling panelm

2 23.06 23.07 23.07 23.07 23.07

5.2 Metal Framed Ceilings (Concealed Grid)

Recessed grid type suspended ceiling

comprising galvanised steel suspension tees

with aluminium flanged cappings arranged in

grid including 6mm diameter steel rod

hangers,clips and rivetting to all ends of grids

along the boundaries

A 16mm thick Armstrong Minatone Fissured'

mineral fibre boardm

2 36.97 36.77 36.77 36.83 36.83

B 19mm thick Armstrong Travertone Sanserra'

acoustical mineral fibre boardm

2 38.68 38.45 38.45 38.50 38.50

C 12mm thick fibrous qypsum board m2 34.65 34.45 34.45 34.45 34.33

D 16mm thick fibrous gypsum board m2 42.23 41.97 41.97 41.97 41.67

5.3 Timber Ceilings

Ceiling board nailed, pinned or screwed to and

including 50x50mm pressure impregnated

kapur frames at 600mm centres bothways and

hangers

A 12mm thick fibrous gypsum board,including

pointingm

2 36.17 36.17 36.17 36.17 36.17

B 8mm thick plain plasterglass board m2 41.50 41.50 41.50 41.50 41.50

Page 24/34

8/6/2019 BCA unitrates 13 05 2011

25/34


MEAN

2010Q2

MEAN

2010Q3

MEAN

2010Q4

MEAN

2011Q1

MEAN

5.3 Timber Ceilings

`Celotex' Hytone baroque or other equal and

approved non-combustible random fissured

mineral fibre board ceiling of panel size

C 600 x 1200 x 19mm thick m2 27.30 27.30 27.30 27.30 27.30

Suspended fibrous plasterboard ceiling with

sealed joints fixed to & including suspension

system

D 12mm thick m2 35.74 35.74 35.74 35.74 35.73

E 19mm thick m2 43.77 43.77 43.77 43.77 43.83

5.4 Metal Ceilings

Linear metal suspended ceiling with

chromated and stove enamelled finishes

including galvanised steel runners,

hangers,adjustment clips and fixing

accessories

A Luxalon type 84C aluminium perforated linear

ceilingm

2 78.59 78.59 78.59 78.67 78.67

B `Luxalon' lineal strip suspended ceiling system m2 82.65 82.65 82.65 82.65 82.67

C 101x0.6mm thick Luxalon Type V100'

aluminium screen ceilingm

2 79.71 79.71 79.71 79.71 79.67

D 0.6mm Dampa 200 type perforated aluminium

strip ceilingm

2 79.82 79.82 79.82 80.12 80.12

Page 25/34

8/6/2019 BCA unitrates 13 05 2011

26/34


MEAN

2010Q2

MEAN

2010Q3

MEAN

2010Q4

MEAN

2011Q1

MEAN

VIII FLOOR FINISHES

1 IN-SITU FINISHES

1.1 Plain Paving

Cement and sand (1:3) paving including

trowelling smooth

A average 20mm thick m2 10.68 11.35 11.98 12.03 12.08

B average 25mm thick m2 12.15 12.83 13.55 13.63 13.68

C average 32mm thick m2 13.13 13.83 14.53 14.60 14.68

D average 38mm thick m2 14.03 14.73 15.48 15.60 15.65

E average 50mm thick m2 17.35 18.13 19.00 19.20 19.28

F add or deduct each 10mm thickness m2 1.52 1.52 1.52 1.52 1.52

1.2 Waterproofed Paving

Waterproofed cement and sand (1:3) paving

with Sika `No 1' waterproofing compound or

equivalent including trowelling smooth

A average 20mm thick m2 14.17 14.20 15.20 15.20 15.23

B average 25mm thick m2 16.07 16.13 17.23 17.23 17.27

C average 32mm thick m2 16.80 16.87 17.80 17.80 17.87

D average 38mm thick m2 17.87 17.93 18.93 18.93 19.00

E average 50mm thick m2 20.73 20.80 22.10 22.10 22.17

1.3 Hardened Paving

25mm thick cement and sand (1:3) paving

mixed with hardener including trowelling

smooth

A light duty metallic hardener (0.25kg of

hardener per kg of cement)m

2 17.17 17.17 17.83 17.83 17.87

B heavy duty metallic hardener (0.5kg of


2 22.73 22.73 23.50 23.50 23.53

50mm thick cement and sand (1:3) paving

mixed with hardener including trowelling

smooth

C light duty non- metallic hardener (0.25kg of


2 18.21 18.21 18.67 18.67 18.67

D heavy duty non-metallic hardener (0.5kg of


2 24.58 24.58 25.17 25.17 25.17

E 3 coats Lapidolith hardener m2 35.69 35.69 35.97 35.97 35.97

F Granolith non-metallic hardener m2 36.58 36.58 36.89 36.89 36.89

G `Mastercon' premixed non-metallic hardener m2 29.94 29.94 30.16 30.16 30.16

H prepare & apply Korodor 04' floor hardener

power trowelled smooth and finish with one

spray coat of `Korotex' curing compound

internally

m2 38.35 38.35 38.71 38.71 38.71

I A-H Silica Quartz hardener m2 44.84 44.84 45.10 45.10 45.10

Unit Rates - Floor FinishesLast Updated on 13/05/11


Page 26/34

8/6/2019 BCA unitrates 13 05 2011

27/34


MEAN

2010Q2

MEAN

2010Q3

MEAN

2010Q4

MEAN

2011Q1

MEAN

1.4 Granolithic Paving

Granolithic aggregate paving consisting of

cement,sand and granite chippings of 5mm

gauge (2:1:5) set out in panels with 15x15mm

deep recessed joints laterally at 1.20m centres

including scrubbing to produce exposed

aggregate finish

A 25mm thick m2 37.23 37.00 37.50 37.57 37.57

B 32mm thick m2 38.34 38.11 38.61 38.78 38.78

C 40mm thick m2 38.70 38.45 38.95 39.15 39.15

D 50mm thick m2 46.46 46.16 46.66 46.80 46.80

1.5 Screed Bed

Cement and sand (1:3) screed to receive floor

finishes

A 13mm thick m2 8.96 9.56 10.10 10.15 10.15

B 20mm thick m2 10.42 11.07 11.73 11.75 11.75

C 25mm thick m2 10.98 11.63 12.28 12.35 12.35

D 32mm thick m2 12.26 12.91 13.63 13.75 13.75

E 38mm thick m2 12.81 13.46 14.23 14.48 14.48

F 50mm thick m2 14.58 15.25 16.00 16.25 16.25

G add or deduct each 10mm thickness m2 1.49 1.49 1.49 1.49 1.49

2 STONE FINISHES

2.1 Labour

Supply labour for laying slabs with and

including pointing with coloured cement

A granite generally m2 66.25 66.25 67.25 67.25 67.25

B marble generally m2 66.25 66.25 67.25 67.25 67.25

3 BRICK FINISHES

3.1 Brick Paving

Supply and lay brick-on-edge paving in

standard size 215x102.5x65mm first quality

red facing brick complying with SS103 in

cement mortar (1:4) with mortar plasticiserincluding pointing in coloured cement

A generally m2 38.59 38.59 38.59 38.59 38.83

4 TILE FINISHES

4.1 Labour for Tiling

Supply labour and mortar for laying tiles

including pointing in coloured cement

A floor and horizontal surface m2 28.28 28.28 28.33 28.33 28.67

B skirting ne 150mm high m 7.02 7.02 7.02 7.02 7.33

C skirting 150-300mm high m 13.63 13.63 13.63 13.63 13.83


laying tiles including pointing with coloured

cement

D floor and horizontal surface m2 30.95 30.95 30.95 30.95 31.00

E skirting ne 150mm high m 7.22 7.22 7.22 7.22 7.33

Page 27/34

8/6/2019 BCA unitrates 13 05 2011

28/34


MEAN

2010Q2

MEAN

2010Q3

MEAN

2010Q4

MEAN

2011Q1

MEAN

4.1 Labour for Tiling


laying tiles including pointing with coloured

cement

F skirting 150-300mm high m 10.38 10.38 10.72 10.72 10.83

5 GLASS BLOCKS

5.1 Floors

Supply and lay glass `Solaris' 190x190x95mm

thick glass block including pointing with white

cement

A generally m2 345.23 345.23 345.23 345.23 345.23

5.2 Walls

95mm `NEG' hollow glass block

A generally m2 310.58 310.58 310.58 310.58 310.58

80mm thick with 6mm galvanised mild steel

rod reinforcement

B generally m2 299.39 299.39 299.39 299.39 299.78

6 VINYL FINISHES

6.1 Vinyl Tiles

Supply and lay vinyl tiles with and including

compatible adhesive for laying vinyl finishes

A 300x300x3mm Armstrong m2 25.18 25.18 25.18 25.18 25.18

B 305x305x2.4mm Armstrong Imperial' m2 24.14 24.14 24.14 24.14 24.14

C 300x300x3.2mm Armstrong Excelon' m2 32.97 32.97 32.97 32.97 32.97

D 300x300x4mm asbestos m2 - - - - -

6.2 Labour for Laying Tiles/Sheet


laying vinyl finishes including hot welding

seam joints with matching welding cord andpolishing

A PVC tiles m2 10.17 10.17 10.17 10.17 10.17

B PVC sheet m2 11.55 11.55 11.55 11.55 11.55

7 CARPET FINISHES

7.1 Labour for Carpeting


laying carpet including foam rubber underlay

and fixing at perimeter

A carpet tile m2 7.56 7.56 7.56 7.56 7.68

B broadloom carpet m2 8.50 8.50 8.50 8.50 8.56

Page 28/34

8/6/2019 BCA unitrates 13 05 2011

29/34


MEAN

2010Q2

MEAN

2010Q3

MEAN

2010Q4

MEAN

2011Q1

MEAN

8 SUNDRIES

8.1 Dividing Strip

Supply and fix 25mm high extruded aluminium

dividing strip to receive edge of floor finish

A 2mm thick m 8.19 8.42 8.42 8.42 8.32

B 3mm thick m 11.14 11.47 11.47 11.47 11.37

C 4mm thick m 14.21 14.63 14.63 14.63 14.53

Page 29/34

8/6/2019 BCA unitrates 13 05 2011

30/34


MEAN

2010Q2

MEAN

2010Q3

MEAN

2010Q4

MEAN

2011Q1

MEAN

IX GLAZING

1 STANDARD GLASS

1.1 In Panes

Obscured glass to timber or metal frame

A 5mm thick m2 57.10 57.10 57.10 57.10 57.28

B 6mm thick m2 62.19 62.19 62.19 62.19 62.51

Clear float glass to timber or metal frame

C 5mm thick m2 39.74 39.81 40.24 40.24 40.74

D 6mm thick m2 54.29 54.36 54.90 54.90 55.46

E 8mm thick m2 61.65 61.75 62.45 62.45 63.18

F 10mm thick m2 97.08 97.08 98.20 98.20 99.15

G 12mm thick m2 118.52 118.70 119.97 119.97 121.17

Tinted float glass to timber or metal frame

H 5mm thick m2 35.97 36.41 36.41 36.41 37.01

I 6mm thick m2 47.31 47.85 47.85 47.85 48.48

J 8mm thick m2 68.10 68.89 68.89 68.89 69.75

K 10mm thick m2 134.25 134.25 134.25 134.25 135.97

L 12mm thick m2 154.70 154.70 154.70 154.70 156.75

Clear laminated float glass to timber or metal

M 6mm thick m2 99.97 99.66 100.22 100.22 100.22

N 8mm thick m2 124.46 124.46 125.17 125.17 125.17

O 10mm thick m2 165.04 164.92 165.88 165.88 165.72

P 12mm thick m2 185.21 186.06 187.16 187.16 187.16

Tinted laminated float glass to timber or metal

frame

Q 5mm thick m2 94.45 94.45 95.03 95.03 94.93

R 6mm thick m2 101.43 101.43 102.05 102.05 102.05

S 8mm thick m2 125.39 125.39 126.17 126.17 126.00

T 10mm thickm

2 176.91 176.91 177.99 177.99 177.52

U 12mm thick m2 197.54 197.54 198.76 198.76 198.63

Tempered glass

V 12mm thick m2 210.59 210.59 210.59 210.59 205.52

Tinted wired glass

W 6mm thick m2 145.61 145.14 145.14 145.14 145.44

1.2 In Louvres

Obscured glass with ends housed in grooves

of timber frame or fixed to metal clips

A 100x5mm thick m 4.46 4.46 4.54 4.54 4.54

B 100x6mm thick m 5.67 5.67 5.73 5.73 5.73

C 150x5mm thick m 6.29 6.29 6.40 6.40 6.40

D 150x6mm thick m 7.57 7.57 7.70 7.70 7.70

Clear float glass with ends housed in grooves


E 100x5mm thick m 4.05 4.05 4.05 4.05 4.06

Unit Rates - GlazingLast Updated on 13/05/11


Page 30/34

8/6/2019 BCA unitrates 13 05 2011

31/34


MEAN

2010Q2

MEAN

2010Q3

MEAN

2010Q4

MEAN

2011Q1

MEAN

1.2 In Louvres

Clear float glass with ends housed in grooves


F 100x6mm thick m 5.61 5.66 5.83 5.83 5.90

G 150x5mm thick m 5.83 5.87 6.00 6.00 6.07

H 150x6mm thick m 6.73 6.81 6.93 6.93 7.00

Tinted float glass with ends housed in grooves


I 100x5mm thick m 4.72 4.72 4.72 4.72 4.79

J 100x6mm thick m 5.70 5.70 5.70 5.70 5.73

K 150x5mm thick m 6.07 6.07 6.07 6.07 6.10

L 150x6mm thick m 7.54 7.54 7.54 7.54 7.57

Georgian wired polished glass with ends

housed in grooves of timber frame or fixed to

metal clips

M 100x6mm thick m 14.82 14.82 14.82 14.82 14.82

N 150x6mm thick m 22.27 22.27 22.27 22.27 22.27

1.3 In Panels/Doors

Clear float toughened glass

A 6mm thick m2 94.46 94.46 95.59 95.59 95.59

B 8mm thick m2 118.03 118.03 119.46 119.46 119.46

C 10mm thick m2 142.64 142.64 144.47 144.47 144.47

D 12mm thick m2 188.90 188.90 191.16 191.16 191.16

Tinted float toughened glass

E 6mm thick m2 96.26 96.26 96.26 96.26 96.59

F 8mm thick m2 125.47 125.47 125.47 125.47 125.60

G 10mm thick m2 162.11 162.11 162.11 162.11 162.28

H 12mm thick m2 205.09 205.09 205.09 205.09 205.29

2 SPECIAL GLASS

2.1 Mirrors

Polished plate glass mirror with copper

backing plugged to wall including chromium

plated mirror screws and felt washersA 3mm thick clear mirror m

2 86.72 86.72 86.72 87.12 88.12

B 3mm thick tinted mirror m2 92.03 92.03 92.03 92.86 93.53

C 6mm thick clear mirror m2 204.19 198.82 198.82 201.35 203.02

D 6mm thick tinted mirror m2 201.96 201.96 201.96 203.79 205.46

Bevelling to straight or circular edges including

internal mitres and scallops

E 8mm wide m 57.50 57.50 62.67 63.48 64.20

F 10mm wide m 64.17 64.17 69.67 70.54 71.31

G 12mm wide m 71.40 71.40 77.48 78.45 79.32

Page 31/34

8/6/2019 BCA unitrates 13 05 2011

32/34


MEAN

2010Q2

MEAN

2010Q3

MEAN

2010Q4

MEAN

2011Q1

MEAN

X PAINTING

1 PAINT APPLICATION

1.1 General Surfaces

Painting concrete or plastered surface and the

like

A two coats of cement paint m2 3.14 3.11 3.11 3.11 3.11

B two coats of water repellant solution m2 3.21 3.14 3.14 3.14 3.14

C one base coat of cement paint, one undercoat

and one finishing coat of acrylic emulsion paintm

2 3.58 3.61 3.61 3.61 3.78

Painting concrete or plastered surface and the

like

D one coat of anti-alkali sealer, one undercoat

and one finishing coat of PVA based emulsion

paint

m2 3.68 3.65 3.65 3.65 3.68

E one coat of oil based anti-alkali sealer, oneundercoat and one finishing coat of acrylic

emulsion paint

m2

4.63 4.63 4.63 4.63 4.65

F one coat of epoxy primer and one coat of

polyurethane paintm

2 9.93 9.93 9.93 9.93 10.00

G one coat of latex primer and two finishing

coats of alkyd semi-gloss enamel paintm

2 7.78 7.78 7.78 7.78 7.78

H one coat of metal primer and 2 coats of

enamel paintm

2 8.48 8.48 8.48 8.48 8.49

I one undercoat and two finishing coats of gloss

oil paintm

2 3.68 3.68 3.68 3.68 3.73

J one coat of primer sealer and three finishing

coats of PVA based emulsion paintm

2 5.83 5.83 5.83 5.84 5.84

K one undercoat two finishing coats synthetic

emulsion paintm

2 3.32 3.32 3.32 3.32 3.36

L two finishing coats of epoxy paint m2 12.40 12.40 12.40 12.40 12.54

M one coat of primer sealer and two finishing

coats of emulsion paintm

2 3.25 3.25 3.25 3.25 3.29

N spray applied two coats of `Flakeline 251' flake

reinforced Bisphenol polyyester resin based

lining

m2 96.13 96.13 96.13 96.13 96.13

O two coats of Sandtex Matt' m2 12.71 12.71 12.71 12.71 12.71

P one coat of primer sealer, one body texture

coat and one finishing coat of polyurethane

finish

m2 10.82 10.82 10.82 10.82 11.00

Q one undercoat and two finishing coats of

weathershield emulsionm

2 5.92 5.92 5.92 5.92 5.75

R Lenaluck acrylic texture spray coating finishes m2 18.05 18.05 18.05 18.05 18.05

S one undercoat and two finishing coats of gloss

enamel three coats of `Methalack-C' coating

system

m2 42.98 42.98 42.98 42.98 42.98

Unit Rates - PaintingLast Updated on 13/05/11


Page 32/34

8/6/2019 BCA unitrates 13 05 2011

33/34


MEAN

2010Q2

MEAN

2010Q3

MEAN

2010Q4

MEAN

2011Q1

MEAN

1.1 General Surfaces

T one coat of plaster sealer, one undercoat and

two coats of solvent based acrylic coatingm

2 3.91 3.91 3.91 3.91 3.94

U one undercoat and one finishing coat with

transparent clear coating of `Cemetex' glazed

coating

m2 3.36 3.36 3.36 3.36 3.36

1.2 Timber Surfaces

Painting timber surfaces

A two coats of aluminium wood primer m2 7.36 7.36 7.36 7.36 7.36

B two coats of wood preservative painting

wrought woodwork surfacem

2 3.36 3.36 3.36 3.36 3.36

C two coats of stain and two coats of wax polish m2 5.45 5.45 5.45 5.45 5.45

D two coats of varnish m2 10.20 10.20 10.20 10.20 10.43

Painting timber surfaces

E one coat of aluminium wood primer, one

undercoat and two finishing coats of synthetic

enamel paint

m2 9.10 9.10 9.10 9.10 9.10

F one coat of stain and three coats of clear

polyurethane

m2 9.63 9.63 9.63 9.63 9.63

G two coats staining, varnishing three coats of

translucent finish on woodm

2 10.10 10.10 10.10 10.10 10.10

1.3 Metal Surfaces

Painting on metal surface

A two coats of aluminium paint m2 4.08 4.08 4.08 4.08 4.11

B one undercoat and two finishing coats of

synthetic enamel paintm

2 8.56 8.56 8.56 8.56 8.73

C two coats of zinc chromate primer, one


enamel paint

m2 10.06 10.20 10.20 10.20 10.30

D one coat of intergard EPA 500/EPA 5001 anti-

corrosive primer, one undercoat of intergard

EPA 003/EPA 746 Mastic Mio aluminium andone recoatable finishing coat of series/PQA

015 or other similar approved paint

m2 45.74 45.74 45.74 45.74 45.74

1.4 Weldmesh Surfaces

Painting on both sides of weldmesh

(measured flat on one side)

A two coats of aluminium paint m2 9.54 9.54 9.54 9.54 9.56

B one undercoat and two finishing coats of

synthetic enamel paintm

2 14.13 14.13 14.13 14.13 14.18

C two coats of zinc chromate primer, one


enamel paint

m2 - - - - -

1.5 Cast Iron Pipe Surfaces

Knot and apply two coats of aluminium primer,

one undercoat and two finishing coats of

synthetic enamel paint

A small pipe m 2.33 2.33 2.33 2.71 2.54

B large pipe m 2.84 2.84 2.84 3.38 3.51

Page 33/34

8/6/2019 BCA unitrates 13 05 2011

34/34


MEAN

2010Q2

MEAN

2010Q3

MEAN

2010Q4

MEAN

2011Q1

MEAN

1.6 Galvanised Pipe Surfaces

Two coats of zinc chromate primer, one


enamel paint

A small pipe m 2.15 2.15 2.15 2.31 2.34

B large pipe m 2.63 2.63 2.63 2.88 2.94

1.7 Copper Pipe Surfaces

One coat of etch primer, one undercoat and

two finishing coats of synthetic enamel paint

A small pipe m 1.66 1.66 1.66 1.81 1.87

B large pipe m 2.15 2.15 2.15 2.34 2.41

1.8 UPVC Pipe Surfaces

One coat of polyvinyl acetate primer, one


enamel paint

A small pipe m 2.38 2.38 2.38 2.54 2.54

B large pipe m 2.89 2.89 2.89 3.04 3.04

1.9 Fire Protection

Provide and spray vermiculite to general

surface

A 13mm thick m2 22.58 22.58 22.58 22.58 23.25

B 25mm thick m2 32.63 32.63 32.63 32.63 33.30

C 50mm thick m2 42.94 42.94 42.94 42.94 43.94

GPG fire rating compound

D generally m2 - - - - -

Mandolite P20 2 hours fire protection

E beam girders m2 42.06 42.06 42.06 42.06 44.77

`Blobest-RS' 2 hours fire protection

F beam m2 42.06 42.06 42.06 42.06 44.77

2.0 Labour

Supply labour to prepare and apply paint on

A concrete or plastered surface m2 1.24 1.26 1.26 1.26 1.26

B timber surface m2 1.24 1.26 1.26 1.26 1.26

C metal surface m2 1.24 1.26 1.26 1.26 1.26

D large pipe surface m2 1.24 1.26 1.26 1.26 1.26

E small pipe surface m2 1.24 1.26 1.26 1.26 1.26

BCA unitrates 13 05 2011

Documents

Transcript of BCA unitrates 13 05 2011