01-Gen Sinkron2tak Serempak

1

RE1345 RE1345

KONVERSI TENAGA LISTRIK II KONVERSI TENAGA LISTRIK II

Vita LystianingrumVita Lystianingrum

2

RE1345 KONVERSI TENAGA LISTRIK IIRE1345 KONVERSI TENAGA LISTRIK II SILABUSSILABUS

RE1345 Konversi Tenaga Listrik IIElectrical Power Conversion II

Semester IV 2SKS

Tujuan:Memahami tentang dasar-dasar mesin listrik arus bolak-balik, khususnya: generator serempak, motor serempak, motor tak serempak.

Prasyarat:Konversi Tenaga Listrik I

3

RE1345 RE1345 KONVERSI TENAGA LISTRIK IIKONVERSI TENAGA LISTRIK II

1: Klasifikasi mesin-mesin listrik dan konstruksi 2: Generator sinkron: proses terbangkitnya EMF dan macam-macam

generator sinkron 3: Generator sinkron: berbeban, kerugian tegangan, diagram vektor

untuk pf. lagging, pf. leading 4: Generator sinkron: menentukan voltage regulator dengan metode

EMF dan karakteristik 5: Generator sinkron: kerja paralel 6:7: Motor sinkron: metode start dan pengaruh perubahan arus eksitasi 8: Motor sinkron: torque dan contoh soal 9 & 10: UTS

4

ReferencesReferences

1. Theraja, B. L., ‘Electrical Technology’, S. Chand & Company Ltd., 1978.

2. Karady, G., ‘Lecture Notes on Synchronous Generator’, www.eas.asu.edu/~karady/360_pp.html.

3. Zuhal

5

• Motivasi, Tujuan:– Menambah wawasan?

• MAteri kuliah bisa didownload di: www.oc.its.ac.id

• Komposisi Nilai– Tugas 20 %– UTS 40 %– UAS 40 %

• Peraturan Kelas– Kelas dimulai jam 7.30

6

Review KTL 1:Review KTL 1:DC MachinesDC Machines

• Generators convert mechanical energy to electric energy.

• Motors convert electric energy to mechanical energy.

• Faraday’s Law

-> Dynamically & statically induced.

• The construction of motors and generators are similar.

7

DC generatorDC generator

8

DC generatorDC generator

9

carbon brushes

DC Motor DC Motor PartsParts

Field magnet

stator

rotor

10

AC Generators / AlternatorsAC Generators / Alternators

• Same principles as DC generators -> armature winding & magnetic field.

• Armature winding -> statorfield winding -> rotor

**

11

Why stationary armature?Why stationary armature?

• Without brush contact->The output current can be led directly from fixed terminals on the stator (armature windings) to the load circuit.

• Easier to insulate stationary armature winding for high AC voltages (may be as high as 30 kV or more)

• Sliding contacts i.e. slip-rings are transferred to the low-voltage, low-power DC field circuit-> easily insulated

• **Armature windings can be more easily braced to prevent any deformation produced by the mechanical stresses

12

SYNCHRONOUS MACHINESSYNCHRONOUS MACHINES

Stator Rotor

Connections

Bearing

Stator winding

Rotor winding

Housing ,cooling ducts

Shaft

13


Stator• Laminated iron

core with slots• Steel Housing

14


Stator details• Coils are placed in

slots

• Coil end windings are bent to form the armature winding.

Slots

Coil

End winding

Iron core

16

??

18

**2 kinds of rotor**2 kinds of rotor

19


Round rotor

Steel ring

DC current terminals

Wedges

Shaft

20


Rotor Details

21


Round rotor

• The round rotor is used for large high speed (3600rpm) machines.

• A forged iron core (not laminated,DC) is installed on the shaft.

• Slots are milled in the iron and insulated copper bars are placed in the slots.

• The slots are closed by wedges and re-enforced with steel rings.

Round rotor

22


Round Rotor Machine

• The stator is a ring shaped laminated iron-core with slots.

• Three phase windings are placed in the slots.

• Round solid iron rotor with slots.

• A single winding is placed in the slots. Dc current is supplied through slip rings.

Concept (two poles)

N S

A

-B

+

A

+C

+

C

-

B

-

A

B

CStator with laminated iron-core

Slots withwinding

Rotor with dcwinding

23

Salient rotorSalient rotor

• Usually for low- & medium-speed alternators

24


Salient Rotor Machine• The stator has a laminated

iron-core with slots and three phase windings placed in the slots.

• The rotor has salient poles excited by dc current.

• DC current is supplied to the rotor through slip-rings and brushes.

• Concept (two poles)

N

S

A+

B+

C+B-

A-

C-

26


Construction

• The picture shows the laminated iron core and the slots (empty and with winding).

• The winding consists of copper bars insulated with mica and epoxy resin.

• The conductors are secured by steel wedges.

• In large machines, the stator is liquid cooled.

• The iron core is supported by a steel housing.

• Construction

empty slots

insulated winding

27


Salient pole rotor construction

• The poles are bolted to the shaft.• Each pole has a DC winding.• The DC winding is connected to the slip-rings (not shown).• A DC source supplies the winding with DC through brushes

pressed into the slip ring. • A fan is installed on the shaft to assure air circulation and

effective cooling.

28


29


Construction• Low speed, large hydro-

generators may have more than one hundred poles.

-> relationship between speed & poles

• These generators are frequently mounted vertically.

• The picture shows a large, horizontally arranged machine.

30

• Thank You, see you next week

31

• Different construction of synch. Gen & DC gen ->

• Which one precedes?

01-Gen Sinkron2tak Serempak

Documents

Transcript of 01-Gen Sinkron2tak Serempak