Post on 21-Jan-2023
TQF-PCS-016
TQF Management Technical Specifications—Certification Regulation Ver. 2.0
1 / 66 ©Taiwan Quality Food Association
[Canned Food]
Specific Provisions for TQF Canned Food Factories
1 Purpose
This specifications provide special guidance for food factories to ensure that during food processing, packaging and transportation, the personnel, premises, facilities, equipment, and sanitary, processing, and quality management are in conformity with good manufacturing practices benchmark and that through the principle of hazard analysis and critical control points (HACCP) will prevent operating under unsanitary conditions, and in environments that may cause food contamination or quality deterioration. It also aims to reduce operation errors and to establish a sound quality assurance system to ensure food safety and product quality stability.
2 Scope of application
The scope of this guidance is applicable to food factories which supply properly packaged canned food for human consumption.
3 Definition of special terms
3.1 Food: Refers to the products and their raw materials for human consumption, either
for eating, drinking or chewing.
3.1.1 Canned Foods: Foods sealed in hermetic containers where commercial
sterilization is performed before and after seaming to ensure long-term storage at room
temperature.
3.1.1.1 Low-acid canned foods (LACFs): Non-alcoholic beverages and canned
foods with a pH value above 4.6 and water activity above 0.85 after
contents reach an equilibrium, and sterilized using a method with a
sterilizing value (F0) above 3.0.
3.1.1.2 Acidified canned foods: Canned foods made with low-acidic or acidic
foods with pH value adjusted by acidifiers and/or acidic foods to maintain
their final pH value below 4.6 (water activity (Aw) above 0.85).
3.1.1.3 Acid canned foods: Canned foods without added acidifiers or acidic foods
during processing, with a pH value at or below 4.6 (water activity (Aw)
above 0.85) in the final equilibrium.
3.1.1.4 Low water activity canned foods: Canned foods that do not have any added
acidifying agent or acidic food during processing and with water activity
below 0.85 and a pH value at 4.6 or above.
3.2 Food factory: refers to the registered factories and manufacturers of properly
TQF-PCS-016
TQF Management Technical Specifications—Certification Regulation Ver. 2.0
2 / 66 ©Taiwan Quality Food Association
[Canned Food]
packaged food, which main products are included in the product categories of
product certification application.
3.3 Materials: Refers to raw materials and packaging materials.
3.3.1 Raw materials Refers to the constituents in edible parts of finished product, including primary raw materials, secondary raw materials, and food additives.
3.3.1.1 Primary raw materials: Refers to the major materials used for
manufacturing finished products.
3.3.1.2 Secondary raw materials: Refers to the raw materials used for
manufacturing finished products excluding primary materials and food
additives.
3.3.1.3 Refers to the material which is added to or brought into contact with food
in the course of manufacturing, processing, mixing, packing, transport and
storage of food, with the purpose of coloring, seasoning, preserving,
bleaching, emulsifying, flavoring, stabilizing the quality, fermentation,
increasing viscosity, nutrition fortification, preventing oxidation or other
necessary purpose and added to or come in contact with food unit or
compound.
3.3.2 Packaging material: Refers to the material used as the inner and outer
packaging.
3.3.2.1 Inner packaging material: Refers to the container which is brought into
direct contact with food, such as bottle, tin can, carton, pouch etc. and to
the packaging material which wraps and covers directly the food, such as
foil, film, paper, waxed paper etc. All those materials shall be in
compliance with food sanitation and hygiene laws and regulations.
3.3.2.2 Outer packaging material: Refers to the packaging material which is not
brought into direct contact with food, such as label, carton, wrapping
materials etc.
3.4 Product: Refers to semi-finished product, bulk product and finished product.
3.4.1 Semi-finished product: Refers to the partly processed product which
must undergo further processing before it becomes a finished product.
3.4.2 Bulk product: Refers to the product which had undergone complete
processing, but not packaged or labelled.
3.4.3 Finished product: Refers to the product which has undergone all stages
of manufacturing with packaging and labeling.
3.5 Premises: Refers to the entire or partial plant construction or facilities which are
TQF-PCS-016
TQF Management Technical Specifications—Certification Regulation Ver. 2.0
3 / 66 ©Taiwan Quality Food Association
[Canned Food]
used in food processing, packaging, storage etc. or their relevant operation.
3.5.1 Food processing and operation areas: Refers to the areas for handling
raw material, manufacturing, processing and preparation, and packaging
and storage.
3.5.1.1 Raw material handling area: Refers to the area that is provided for raw
material to undergoing preparation, thawing, sorting, cleaning, trimming,
cutting, peeling, hulling, entrails removal, blanching or salting operation.
3.5.1.2 Processing and preparation area: Refers to the area that is provided for
materials processing operations to undergoing cutting, grinding, mixing,
blending, moulding, shaping, cooking, extracting and improving food
characteristic or preservation (such as oil extraction, starch separation,
bean paste manufacturing, emulsification, coagulation, fermentation,
sterilization, freezing or drying, etc.).
3.5.1.3 Packaging room: Refers to the place for packaging of finished product,
which includes the rooms for inner and outer packaging.
3.5.1.3.1 Inner packaging room: Refers to the place for inner packaging
operation in which the packaging material is in direct contact with the
product content.
3.5.1.3.2 Outer packaging room: Refers to the place for outer packaging operation in which the packaging material is not in direct contact with the product content.
3.5.1.4 Sterilization site: A workplace for sterilizing products.
3.5.1.5 Inner packaging material preparation room Refers to the place where the inner packaging materials that can be used directly without requiring any further cleaning and disinfection procedures go through pre-forming or have their outer packaging removed.
3.5.1.6 Buffer room Refers to the area that was set up at the entrance of the controlled operation area to avoid its direct connection with the exterior, when raw materials or semi-finished products are not going through normal manufacturing process and have directly accessed to the operation area.
3.5.1.7 Weighing room
Refers to the area for weighing operation of raw materials, secondary raw materials, food additives, ingredients etc..
3.5.2 Controlled operation area
Refers to the areas where higher degree of cleanliness are required, including clean operation area and semi-clean operation area. The entrance for both people and raw material and the prevention of pests and vectors invasion in those areas
TQF-PCS-016
TQF Management Technical Specifications—Certification Regulation Ver. 2.0
4 / 66 ©Taiwan Quality Food Association
[Canned Food]
shall be strictly controlled.
3.5.2.1 Clean operation area
Refers to the area such as the inner packaging room among others where it
is required highest degree of cleanliness.
3.5.2.2 Semi-clean operation area
Refers to the processing, preparation areas among others where the
required degree of cleanliness were below the clean operation area.
3.5.3 General operation area Refers to the storage of raw material, storage of ingredients and outer packaging room among others where the required degree of cleanliness were below the controlled operation area.
3.5.4 Non-food handling area
Refers to the quality control (laboratory) room, office, rest room and toilet where there is not direct involvement with food preparation or processing.
3.6 Cleaning
Refers to the operation of removing dust, scrap, stain, dirt or other possible
impurities that may contaminate the food.
3.7 Disinfection
Refers to appropriate operations to effectively kill and remove pathogenic
micro-organisms without affecting food quality or safety, by using chemical
reagent and (or) physical method in compliance with food hygiene.
3.8 Sealed containers: A sealed container that can prevent the intrusion or
exchange of foreign substances (e.g. microorganisms, water vapor, gases),
including metal, glass, retort pouches, plastic, and laminate composite
containers; and other containers meeting the above requirements.
3.9 Commercial sterilization
3.9.1 Commercial sterilization of foods: A commercial sterility processing
method used to ensure that there are no active microorganisms or spores
that are hazardous to human health are present in foods; and inhibit the
activity of food spoilage microorganisms to ensure that no
microorganisms can grow or toxins are produced in products during
storage and transportation at ambient temperature before expiration.
3.9.2 The equipment and containers for aseptic processing and packaging of
foods by using commercial sterilization: A commercial sterility
processing method used to achieve the commercial sterilization of
equipment and containers with thermal treatment, chemicals (e.g.
TQF-PCS-016
TQF Management Technical Specifications—Certification Regulation Ver. 2.0
5 / 66 ©Taiwan Quality Food Association
[Canned Food]
hydrogen peroxide), or other effective methods and to ensure that there
are no active microorganisms or spores that are hazardous to human
health are present in foods; and inhibit the activity of food spoilage
microorganisms to ensure that no microorganisms can grow or toxins
are produce in products during storage and transportation at ambient
temperature before expiration.
3.10 Aseptic processing and packaging system: A canned food manufacturing system in
which foods and containers are individually sterilized appropriately before filling,
transporting, and seaming in an aseptic environment.
3.11 Sterilizing value (F0-value): Measured in minutes, which represents the ability to
kill bacteria or their spores (e.g. clostridium botulinum), with possessing a Z-value
of 18°F, expressed in terms of equivalent thermal death time at a temperature of
250°F (121.1°C). For example, the heating condition of a 95 grams canned food
product is the following: heat for 9 minutes with an initial temperature of 60°C and
sterilizing at 120°C for 40 minutes. If the F0-value of this condition is 7.5, it means
that the equivalent thermal death time at 250°F (121.1°C) is 7.5 minutes.
3.12 D-value and Z-value: The D-value refers to the time required for killing 90% of the
microorganisms at a temperature, i.e. the time required for the thermal destruction
curve to move one log cycle. The Z-value is the degree of temperature changed
needed for a change of the D-value with a factor of 10 for certain bacteria. In other
words, it is the required degrees of temperature of the thermal resistance curve of
bacteria to move one log cycle.
3.13 Sterilizing condition: Controls and sterilization processes adopted to achieve the
commercial sterilization for the safety of canned foods.
3.14 Critical factors of sterilization: The properties and processing requirements of
specific canned foods that will affect the lethality of sterilization effect and cause
product safety, which including can shape and size, formula, sugar Brix, starch
concentration, viscosity, solid contents or ingredients, total volume or solid-to-
liquid ratio, initial temperature, heating time, slicing size and shape, filling method,
the way of loading and stocking of product, sterilizing temperature and time, water
activity, vacuum degree, and headspace.
3.15 Initial temperature: The equilibrium temperature at the coldest point, before the
start of sterilization process in the loaded canned food.
3.16 Heating-up time: the time from when the steam starts to be introduced into the
sterilizer until the start of sterilization.
3.17 Insulation test: The test of placing the sample at a selected temperature for a period
TQF-PCS-016
TQF Management Technical Specifications—Certification Regulation Ver. 2.0
6 / 66 ©Taiwan Quality Food Association
[Canned Food]
of time to allow the growth of microorganisms.
3.18 Food-grade detergent
Refers to the substances employed in cleaning the equipment, utensils, containers
and packaging materials and shall not bring any risk for the food safety and
hygiene.
3.19 Foreign matters:
Refers to any contaminant or undesirable substances which are mixed or adhered in
the raw material, semi-finished product, finished-product or inner packaging
materials during processing (excluding raw material), making the food to be unsafe
and unhygienic.
3.20 Pest
Refers to small animal or insect which direct or indirectly contaminate the food or
disseminate diseases, such as rats, cockroaches, flies and vermin.
3.21 Pathogenic micro-organism
Refers to the microorganism capable of causing food quality deterioration and
having public health significance.
3.22 Prevention of vector-borne infestation
Refers to appropriate and tangible isolation means to prevent vector invasion, such
as traps, fence with appropriate aperture, gauze, etc.
3.23 Sanitation management personnel
Refers to the staff responsible for the sanitation of the interior and exterior
environment of a plant, the premises and facilities and the health and hygiene of
personnel.
3.24 Food contact surface
Refers to the food direct or indirect contact surfaces, including utensils and
equipment contact surface with the food. The food indirect contact surface: Refers
to the contact surface between food and those surfaces from which drainage onto
the food or onto surfaces that contact the food ordinarily occurs under normal
processing condition.
3.25 Shall
Refers to a requirement that is mandatory.
3.26 Should
Refers to a guideline or recommendation.
3.27 Food appliances and utensils
Refers to the devices, tools or utensils in direct contact with food or food
TQF-PCS-016
TQF Management Technical Specifications—Certification Regulation Ver. 2.0
7 / 66 ©Taiwan Quality Food Association
[Canned Food]
additives.
3.28 Safe moisture level
Refers to a reference level of moisture which can prevent the survival of
pathogenic microorganisms, under pre-established processing, storing and
distributing conditions. Basically, a maximum safe moisture level for food is
indicated by water activity (Aw). The water activity is considered to be safe to the
food if there is sufficient data to show that it does not contribute to the growth of
pathogenic microorganisms under a certain water activity.
3.29 Water activity
Refers to the indicator of free water in foods, and is the quotient of the water vapor
pressure of the food divided by the vapor pressure of pure water under the same
temperature.
3.30 High water activity finished product
Refers to finished product’s water activity that are above 0.85 (inclusive).
3.31 Low water activity finished product
Refers to finished product’s water activity that are below 0.85.
3.32 Appropriate
Refers to the measures taken for intending to complete the expected target or result
under good sanitary operation condition.9
3.33 Lot number
Refers to the specific letters, numbers or symbols for tracing back its processing
history of each batch, while “lot” alone refers to the specific quantity of product
produced during a specific period of time or location.
3.34 Labeling
Refers to the text, pictures or symbols affixed on food, food additive or container
of food-grade detergent and packaging for indicating its name or a descriptive
information.
3.35 Isolation
Refers to the partition of sites and facilities by physical means.
3.36 Separation
Separation has a broader meaning than isolation, including, physical and non-
physical means of partition. Separation of operation area may be accomplished by
one or more of the following ways, such as separation in terms of space, time, and
control of air flow, use of closed system or other effective methods.
3.37 Food Safety Management System
A systematic approach to the identification, evaluation and control of food safety
TQF-PCS-016
TQF Management Technical Specifications—Certification Regulation Ver. 2.0
8 / 66 ©Taiwan Quality Food Association
[Canned Food]
hazards, invoke the principle of hazard analysis and critical control points
(HACCP), and manage food safety hazards throughout the reception of raw
materials and ingredients, the manufacture, packaging, storage and distribution.
3.38 Critical Control Points (CCP)
Refers to a point, step, or procedure of food manufacturing at which control can be
applied and prevent, eliminate or reduce a food safety hazard to an acceptable
level.
3.39 Control limits
Refers to a maximum and/or minimum value to which a physical, biological or
chemical parameter must be controlled at a CCP to prevent, eliminate or reduce to
an acceptable level the occurrence of a food safety hazard.
3.40 Deviation
Failure to meet a critical control limit.
3.41 Hazard Analysis and Critical Control Points (HACCP) Plan
The written document which is based upon the principles of HACCP and which
delineates the procedures to be followed.
3.42 Hazard
A biological, chemical, or physical agent that is most likely to cause illness or
injury on consumers in the absence of its control.
3.43 Hazard Analysis
The process of collecting and evaluating information on hazards associated with
the food under consideration to decide which are significant and must be addressed
in the HACCP plan.
3.44 Monitoring:
To conduct a planned sequence of observations or measurements to assess whether
a CCP is under control and to produce an accurate record for future use in
verification.
3.45 Control Measure:
Any action or activity that can be used to prevent, eliminate or reduce a significant
biological, chemical, or physical hazard.
3.46 Validation:
That element of confirmation focused on collecting and evaluating scientific and
technical information to determine if the HACCP plan, when properly
implemented, will effectively control the hazards.
3.47 Verification:
Activities other than monitoring, that determine the validity of the HACCP plan
TQF-PCS-016
TQF Management Technical Specifications—Certification Regulation Ver. 2.0
9 / 66 ©Taiwan Quality Food Association
[Canned Food]
and that the system is operating according to the plan, to confirm its effectiveness.
4 Factory Environment
4.1 The food factory shall not be located in areas which are liable to contamination,
except otherwise, there is an effective measure to prevent contamination.
4.2 The surroundings of the plant shall always be easy to clean. The ground shall be
free from puddle of water, mud, dirt, etc. that can cause food contamination, also to
prevent it from being source of pollution. The open ground of the plant site shall be
paved with cement, asphalt or grasses may be planted to prevent dust and beautify
the environment.
4.3 The roads in the vicinity or within the plant shall be paved with cement to prevent
contamination from dust.
4.4 The processing plant shall be free from any facility able to cause odors, harmful
(toxic) gases, smoke, or other unsanitary condition.
4.5 Raising poultry, livestock or pets shall be prohibited inside the plant, with
exception of guard dogs, but they should be properly constrained to avoid
contaminating food.
4.6 A proper drainage system shall be installed inside the plant, the drainage channels
shall be at a proper degree of inclination and the drainage system shall be cleaned
regularly and kept unblocked. Drainage shall be free from bad odor, water puddle,
seeping, silt, dirt, breakage or propagation of vector that could cause food
contamination.
4.7 The surrounding of the production site shall be constructed and designed to
adequately protect against the entrance of external contamination. If fences are
installed, at least 30 cm from the ground shall be constructed with insulated
materials.
4.8 Premises built with staff dormitory and cafeterias, staff lounges, offices or
laboratory, shall be isolated and separated from the manufacturing, preparation,
processing, and food or food additives storage areas, and have good lighting and
ventilation; must be equipped with devices to prevent vector intrusion or microbial
contamination, cleaned regularly and assigned a specialist in charge.
TQF-PCS-016
TQF Management Technical Specifications—Certification Regulation Ver. 2.0
10 / 66 ©Taiwan Quality Food Association
[Canned Food]
5 Premises and Facilities
5.1 Lay-out and Space:
5.1.1 The premises shall be designed to meet food process flow, sanitation
and hygienic requirement, providing good order and tidy conditions,
and to prevent cross-contamination.
5.1.2 The premises shall provide sufficient space for required facilities,
including sanitation facilities, storage areas, staff amenities, etc.
Adequate working space shall be provided to ensure food safety and
sanitation. Food utensils and devices shall have a clean place for
storage. Operational areas for vegetarian food production shall not share
the same production line for the production of non-vegetarian food, and
their utensils and devices shall not be shared. Ovo-vegetarian,
lactovegetarian, ovo-lactovegetarian and strict vegetarian production
site shall have their production line, utensils and devises effectively
separated from the non-vegetarian.
5.1.3 The food processing equipment in a food plant shall be provided with
proper working space or aisles with enough distance in between the
equipment or between the equipment and the walls. It shall provide with
sufficient width to permit employees to carry out their operations
(including cleaning and sanitizing) without contaminating the food,
food-contact surfaces, or packaging material with their clothing or
physical contact.
5.1.4 Laboratory in a food plant shall be provided with enough space for the
installation of experimental table and instruments to perform physical,
chemical, sensorial and (or) microbiological test. Microbiological
testing laboratory shall be properly separated from the other testing
areas, especial isolation shall be made when the laboratory is equipped
with pathogenic microbial testing facility.
5.2 Premises separation
5.2.1 Different purposes premises (e.g. warehouse for raw material,
packaging material, and raw material handling area) shall be built
separately or be effectively separated.
5.2.2 Premises shall be effectively separated or isolated from one another
according to the cleanliness level classification (Table 1).
TQF-PCS-016
TQF Management Technical Specifications—Certification Regulation Ver. 2.0
11 / 66 ©Taiwan Quality Food Association
[Canned Food]
Table 1 Cleanliness Classification of the Processing Zones of Canned Food Factories (Note 1)
Plant facility (arranged by processing order)
Classification of cleanliness level
Receiving Zone Cold Storage Raw materials storage Packaging material storage Raw material handling area Extraction Room (delivery by using closed system equipment
and pipelines) Inner packaging washing area (**) Empty bottles (cans) arrangement area Sterilization treatment area (for closed system equipment and
pipeline)
General operation area
Processing and preparation area Extraction Room (open system equipment) Sterilization treatment area (for closed system equipment) Inner packaging materials preparation room Buffer room Interior packaging (products that are packaged before
sterilization)
Semi-clean operation
area
Controlled operation
area
Interior packaging (products that are sterilized before packaging)
Clean operation
area
Seamed Products Sterilization Zone Exterior Packaging Area Finished product storage
General operation area
Quality control (testing) area Office (***) Change room and hand washing and sanitizing area Toilet other
Non-food handling area
Notes: 1. The classification of cleanliness level of the different operation area can be improved according to actual conditions, and comply with the specific provisions when there is one. 2. The exit of the inner packaging container washing area shall be located within the controlled operation area. 3. The office shall not be located in the controlled operation area (except for the production management and quality control area, but appropriate control measures area required).
5.3 Premises structure The Plant buildings shall be durable, easy to maintain, be kept clean and shall be able to prevent food, food-contact surfaces and inner packaging materials from being contaminated (such as vector intrusion, habitat, breeding, etc.)
TQF-PCS-016
TQF Management Technical Specifications—Certification Regulation Ver. 2.0
12 / 66 ©Taiwan Quality Food Association
[Canned Food]
5.4 Safety facilities
5.4.1 The electricity system installed inside the plant shall be waterproof.
5.4.2 Power supply shall be grounded and with circuit breaker.
5.4.3 The electrical outlet and power switch in workplaces with high
humidity shall be waterproof.
5.4.4 The electrical outlet used for different voltage shall be clearly marked
and labeled.
5.4.5 Fire alarm system shall be set in all buildings and working area,
in accordance with the Fire Services Act.
5.4.6 Ventilation devices shall be equipped in working zones where CO2 and
N2 gases are used.
5.4.7 Fire extinguisher devises and equipment shall be installed in appropriate
places with strict control to prevent food contamination.
5.5 Floor and Drainage
5.5.1 Floor shall be smooth, non-slippery, and kept clean; it shall also be free
from corrosion, cracks or accumulation of water or dust. Floors of the
controlled operation area shall be constructed with water impermeable
materials.
5.5.2 Proper slope (no less than 1/100) and adequate floor drainage system
shall be provided in all areas where floors are subject to flooding-type
cleaning or where normal operations release or discharge water or other
liquid waste on the floor.
5.5.3 Wastewater or effluent disposal shall be made into an adequate
sewerage treatment system or disposed of through other adequate
means.
5.5.4 Drainage system shall be equipped with screen that allow water to flow
and trap to prevent solid wastes from flowing, and free of filthy odor.
5.5.5 No other pipelines shall be arranged inside the drainage system and it
shall remain unobstructed. The joint between the side and the bottom of
the ditch shall have a proper arc (the radius of the curvature shall be
3cm or above).
5.5.6 Drainage outlet shall be equipped with devices to prevent vectors from
entering the facility.
5.5.7 The flow direction of indoor drainage should be from the area with
higher requirement of cleanliness to the area with lower requirement of
cleanliness, and should be designed to prevent the backflow of
TQF-PCS-016
TQF Management Technical Specifications—Certification Regulation Ver. 2.0
13 / 66 ©Taiwan Quality Food Association
[Canned Food]
wastewater.
5.6 Roof and Ceiling
5.6.1 The roofs inside the processing, packaging and storage rooms shall be
easy to clean to prevent dust accumulation, water condensation, mold
growth and it shall not shed particle matters. The V-type supported roof
in the controlled operation area or food exposure area (except for raw
material handling area) which are easy to harbor contaminant, shall be
provided with smooth ceiling easy to be clean. When the construction is
made of reinforced concrete, the roof shall be smooth and free from
cracks and open joints.
5.6.2 The surface of flat-type roof or ceiling shall be constructed with white
or light-colored water proof materials. Where paint spray is required,
the paint shall be anti-mold, not easy to flake off and easy to clean.
5.6.3 Pipes and cables of steam, water or electricity shall not be located
directly above the exposed food, otherwise devices shall be installed to
prevent dust and water condensation from falling, and their exterior
shall be kept clean and cleaned regularly. Air ducts should be located at
the ceiling.
5.6.4 Stairways or over-pass across production lines shall be constructed and
designed so as to avoid food and food contact surfaces in the vicinity
from being contaminated and equipped with safety devices.
5.7 Walls and Windows
5.7.1 The walls inside controlled processing area shall be constructed with
non-absorbent, smooth, easy to clean, water-impermeable and light-
colored materials (except from closed-type fermentation tank, and
outdoor operations). The corner and column feet of the wall shall have
an appropriate arc (with a radius of curvature of 3 cm or above, as
shown in Figure 4-01) to facilitate cleaning and avoid dust and filth
accumulation, except from dryer operation area.
5.7.2 Windows that are opened frequently during operation shall be equipped
with easy-to-dismantle, easy to clean and rust resistant gauze to protect
against food contamination and to prevent vectors from entering the
facility. Windows shall be kept clean and shall not be opened during
operation in the clean operation area. The windowsill in the controlled
production area shall be sloped 45 degree or more (as shown in Figure
TQF-PCS-016
TQF Management Technical Specifications—Certification Regulation Ver. 2.0
14 / 66 ©Taiwan Quality Food Association
[Canned Food]
4-02), if the depth of the windowsill is more than 2 cm. If the depth is
less than 2 cm, the windowsill corner shall be filled with impervious
material.
5.7.3 Windows, doors, and opening entrances in the controlled processing
area shall be provided with automatic closing screened door (or air
curtain), and (or) provided with shoe cleaning and sanitizing equipment
(operation area that needs to be kept dry shall set up shoe changing
facilities). Doors shall be made of smooth, easy to clean and
impermeable strong material, and be kept closed.
5.8 Lighting
5.8.1 Facilities shall be provided with adequate lighting in all areas of the
building, and be kept clean to prevent food contamination. In principle,
the lighting facilities shall not be suspended over exposed food in any
step of the production line, or otherwise, lighting facilities shall be
equipped to prevent food contamination in case of breakage or fall.
5.8.2 Lighting shall be provided so that there shall be no less than 110 lux for
working tables in the general operation area, 220 lux or above for
working tables in the controlled operation area and 540 lux or above for
inspection tables. The source of artificial light shall not alter the original
food color.
5.9 Ventilation
5.9.1 The processing, packaging and storing areas shall be well ventilated,
and the ventilation system shall be kept clean. When necessary effective
ventilation system should be installed to prevent the temperature from
being too high, the air condensation or odor formation, and to keep
indoor air fresh. Clean operation area of perishable ready-to-eat
products and finished products that require transportation at low
temperature shall be equipped with air-conditioning equipment
5.9.2 In the presence of filthy odors and gases (including vapor and toxic
gases) or dusts that may contaminate food, appropriate means of
exclusion, collection or control shall be provided.
5.9.3 The exhaust vent of the controlled operation area shall be equipped with
devices to prevent vectors from entering the facility, and the intake vent
shall be equipped with air purification devices. Both equipment should
be easily disassembled for cleaning or replacement.
5.9.4 Airflow direction from low-cleanliness areas to high-cleanliness areas
TQF-PCS-016
TQF Management Technical Specifications—Certification Regulation Ver. 2.0
15 / 66 ©Taiwan Quality Food Association
[Canned Food]
should be avoided, when air conditioning, air intake and exhaust
systems, or fans are used in the plant to prevent food, food contact
surfaces and internal packaging materials contamination
5.10 Water Supply
5.10.1 Water supply shall be capable of providing sufficient water, with
adequate water pressure and quality to all the food plant. If necessary,
there should be water storage facilities and hot water available.
5.10.2 The reservoirs (towers and tanks) shall be made of non-toxic materials
that do not contaminate the water, they shall be cleaned regularly at
least once a year, kept clean and recorded. Measures shall be taken to
prevent water contamination.
5.10.3 Water used for food manufacturing shall meet potable water quality
standards. When potable water are not used, there shall be a water
purification and disinfection equipment, and pH and chlorine residual
need to be tested, and recorded on a daily basis.
5.10.4 Water used that will have direct contact with foods or for preparing
canned foods shall comply with the drinking water standard.
Water having direct contacts with foods or used for formulating canned foods
shall comply with the drinking water standard.
5.10.5 Pipeline of non-potable water (such as cooling water or waste water)
that shall not be in contact with foodstuffs and the pipeline of water for
food manufacturing shall be clearly distinguished by color and
transported in completely separate piping system, there shall be no
backflow or cross-connection.
5.10.6 Groundwater sources should be located at a distance of more than 15
meters from sources of potential pollution or contamination (septic
tanks, waste dumps, etc.), and water storage facilities should be kept at
a distance of more than 3 meters away from sources of pollution or
contamination (septic tanks, waste dumps, etc.).
5.11 Hand-washing facilities
5.11.1 A sufficient number of hand-washing and hand-dryer facilities shall be
provided at suitable and convenient locations (e.g., at the entrance to the
controlled operation area, toilet and processing area). If necessary,
warm or hot and cold water should be provided, and faucets with
adjustable hot and cold water should be installed.
5.11.2 Liquid soap shall be provided near the hand-washing facilities, and if
TQF-PCS-016
TQF Management Technical Specifications—Certification Regulation Ver. 2.0
16 / 66 ©Taiwan Quality Food Association
[Canned Food]
necessary, hand sanitizers dispensers shall also be provided when
needed (e.g., when hands are at risk of contaminating food if not
disinfected).
5.11.3 The hand washing sink shall be made of impervious material such as
stainless steel and ceramic, and designed so that it can be easily cleaned
and disinfect.
5.11.4 Hand dryer or paper towel shall be used for hand drying. When paper
towels are used, they should be thrown into an easy to clean receptacles
(preferably use foot pedal hands free bins). When using hand dryer, it
shall be cleaned and disinfected regularly to prevent contamination.
5.11.5 Faucets shall be foot pedal operated, elbow operated or electric eye
sensor operated, to prevent re-contamination after cleaning or
disinfecting hands.
5.11.6 Drainage of hand washing facilities shall be fitted with devices to
prevent backflow, vector entry and filthy odor.
5.11.7 A concise and easy understanding hand-washing instruction shall be
posted in the vicinity of the hand-washing facilities.
5.12 Hands-sanitizing room
5.12.1 Separated hands-sanitizing room should be provided in the entrance and
exit of the controlled operation area. (It is a must for the perishable
ready-to-eat food production plant).
5.12.2 In addition to the elements in 5.11, the room should be equipped with
working shoes or boots sanitizing facilities, but shoes changing areas
should be provided in working areas that need to be kept dry. When
boots dips are used, the solution should be kept clean and be able to
cover the shoes upper part. The free residual chlorine concentration
should be maintained at 200ppm or more when chlorine solutions are
used.
5.13 Storage areas
5.13.1 Storage areas for raw material, packaging material, semi-finished and
finished products shall be stored separately and have sufficient space
for transport. Chilled or frozen storage shall be provided when needed.
5.13.2 Raw materials and finished products storage shall be separated or
isolated from the other areas, and different types of items in the same
storage shall also be properly separated.
5.13.3 The storage area shall be constructed so as to minimize the quality
TQF-PCS-016
TQF Management Technical Specifications—Certification Regulation Ver. 2.0
17 / 66 ©Taiwan Quality Food Association
[Canned Food]
deterioration of the raw materials, semi-finished products and finished
products and to prevent contamination. The storage area shall also be
constructed with strong materials, provide sufficient working space and
should be well organized and easy to keep clean. These areas should
also be equipped with devices to protect against the entry of vectors.
5.13.4 Storage areas shall be laid out to permit effective and orderly
segregation of the various categories of materials stored. Materials shall
be stored on pallets, shelves, or other effective method, and keep tidy,
clean, and be at a distance of at least 5cm from the floor and walls.
5.13.5 Chilled (frozen) storage for food products that are more prompt to
microbial growth shall be equipped with accurate temperature sensor,
temperature indicator or automatic temperature recorder, and also
automatic controller or temperature alarm system shall be installed to
alert of abnormal temperature variation.
5.13.6 Chilled (frozen) storage shall be equipped with an alarm switch that
connects to the monitoring department in case a working personnel is
locked inside accidentally or due to any failure and needs to contact and
get assistance from the exterior.
5.13.7 Temperature shall be recorded in the storage area, and also record
humidity when necessary.
5.14 Change room
5.14.1 Change room shall be located in an appropriate and convenient location
near the controlled operation area, and separate dressing room shall be
provided for men and women. Adequate lighting and ventilation shall
also be provided. The change room of a perishable ready-to-eat factory
shall be located near the hand washing and sanitizing area.
5.14.2 There shall be enough space for staff to change clothes, and facilities
such as mirror, dust remover devices and sufficient number of personnel
cabinets or lockers and shoes racks shall be provided in these rooms.
5.15 Toilet facilities
5.15.1 Toilets shall be located in appropriate and convenient places of the plant
to prevent contaminating water source and in sufficient number for the
staff to use.
5.15.2 Flush toilets shall be installed using materials that are impermeable,
easy to clean and sanitize.
5.15.3 Hand washing facilities within the toilet shall be in compliance with
TQF-PCS-016
TQF Management Technical Specifications—Certification Regulation Ver. 2.0
18 / 66 ©Taiwan Quality Food Association
[Canned Food]
element 5.11, and shall be installed near the exit.
5.15.4 Toilet doors shall remain close and shall not face directly toward the
controlled operation area, unless a buffer facility with air curtain control
system to prevent contamination is provided.
5.15.5 Toilets shall be equipped with adequate illumination and well ventilated
to prevent odors. Windows and doors in the toilets shall be equipped
with rustproof screens.
5.15.6 The words "Wash hands after using the toilet" should be clearly
marked.
6 Machine and Equipment
6.1 Design
6.1.1 Food processing equipment shall be designed and constructed in a way
that does not pose a threat to food hygiene. It shall easily be cleaned,
disinfected (and easy to disassemble as possible) and inspected.
Lubricants, metal fragments, contaminated water or other substances
shall not represent a food safety hazard when using these equipment.
6.1.2 The food contact surfaces shall be smooth, free of cracks or
recesses as to reduce the accumulation of food debris, dirt and
organic matter and thus minimize the potential microbiological
growth.
6.1.3 Dead angle, difficult-to-clean areas, or the areas that are prone to
external contamination shall be avoided in utensils and containers, such
as steamers/cookers, mixing tanks, storage tanks (barrels), etc.
6.1.3.1 Utensils and containers shall be equipped with detachable lids and shall
have a flanges design on the rim. Lids that open in the middle shall be
ringed or hinged and pulled from the middle to the sides. Seams that are
designed to be opened in the middle shall be flanged to prevent water, dust,
and foreign matter from entering.
Such utensils and containers shall be equipped with detachable lids
and flanges. Lids opened in the middle shall be ringed or hinged
and pulled from the middle to the sides. The seam in the middle
shall be flanged to prevent water, dust, and foreign matter from
entry.
6.1.3.2 The rim contours on the flange or the bottom shall be round and curves,
TQF-PCS-016
TQF Management Technical Specifications—Certification Regulation Ver. 2.0
19 / 66 ©Taiwan Quality Food Association
[Canned Food]
and sharp angles shall be avoided.
6.1.3.3 Drains shall be equipped at the bottom (the lowest point).
6.1.4 The feeder pump shall be designed for quick disassembly, with a
polished surface, and be free of hollows and cracks to prevent
microorganism from accumulation.
6.1.5 The plants shall avoid installing driving devices, such as motors and
bearings, in overhead locations where foods are exposed. If it is
unavoidable, it shall have appropriate protective devices or trays
underneath such devices to contain the oil and prevent it from falling
onto the foods.
6.1.6 Finished coating (e.g. plating, painting, etc.) surfaces of equipment,
utensils and piping shall ensure that it does not represent any risk to
food and food contact surfaces contamination.
6.1.7 The equipment and utensils, that is within the manufacturing or
processing zones but do not have direct contact with foods, shall have
the structures designed to easily meet the level cleanliness required.
6.2 Material
6.2.1 Equipment and utensils in direct contact with food used in the food
handling area shall be made of nonabsorbent materials that do not
transmit toxic substances, odors, and corrosion resistant, capable of
withstanding repeated cleaning and sanitation. At the same time,
materials that could cause corrosion shall be avoided.
6.2.2 Wood shall not be used as food contact surfaces material unless it is
proved that it will not become a source of contamination.
6.3 Food processing equipment
6.3.1 The food processing equipment in a food plant shall be properly laid out
to meet process flow with sufficient space to avoid cross-contamination.
The production capacity of each equipment should be compatible with
each other.
6.3.2 Instruments or recorders used for measuring, controlling or recording
shall be in good condition and be of suitable accuracy for the intended
use, and periodically calibrated.
6.3.3 Compressed air or other gases which are introduced into food or
used to clean food contact surfaces or equipment shall be
adequately pretreated to prevent indirect contamination.
6.3.4 An LACF factory shall be equipped with appropriate machinery and
TQF-PCS-016
TQF Management Technical Specifications—Certification Regulation Ver. 2.0
20 / 66 ©Taiwan Quality Food Association
[Canned Food]
equipment based on the product needs.
6.4 Sterilization system for low acid canned foods (LACFs)
6.4.1 Static sterilizers
6.4.1.1 Static steam sterilizers
6.4.1.1.1 Mercury-in-glass thermometer
6.4.1.1.1.1 Each sterilizer shall be equipped at least one mercury-in-glass
thermometer with a total length of the scale marks at least 7
inches long, and a maximum of 55 scale division, with accuracy
as low as 0.5°C.
6.4.1.1.1.2 A mercury-in-glass-thermometer shall be calibrated, by an
accredited organization at least once a year, before use. The latest
calibration date and respective calibration data shall be labeled on
the thermometer.
6.4.1.1.1.3 The mercury line in glass shall not be separated and the
thermometer shall be installed in a position where the sterilizer
operators can correctly read the scale.
6.4.1.1.1.4 The mercury bulb shall be installed inside the kettle of the
sterilizer or inside the temperature well linking the kettle. An air
release valve of no less than 1/16th of an inch in diameter shall
be equipped in the temperature well. During the sterilization
process, the valve shall be opened for steam to be continuously
released.
6.4.1.1.1.5 During the sterilization process, the temperature indicated by the
mercury-in-glass thermometer shall be used as the sterilization
temperature, and the temperature indicated on the automatic
temperature recorder shall not function as a substitute.
6.4.1.1.2 Temperature recorder
6.4.1.1.2.1 Each sterilizer shall be equipped with at least one temperature
recorder that can accurately record temperature. The number of
scale marks per inch for a 10°C range of sterilization temperature
recorder chart shall not exceed 25°C in the recorder grid, and the
scale division of a 5°C range of sterilization temperature recorder
chart shall not exceed 1°C. The mercury bulb shall be installed
inside the kettle of the sterilizer or inside the temperature well
linking the kettle. An air release valve of no less than 1/16th of an
TQF-PCS-016
TQF Management Technical Specifications—Certification Regulation Ver. 2.0
21 / 66 ©Taiwan Quality Food Association
[Canned Food]
inch in diameter shall be equipped in the temperature well.
6.4.1.1.2.2 During the sterilization process, the valve shall be opened for
steam to be continuously released.
6.4.1.1.2.3 The temperature indication of the recorder shall be adjusted in
consistent, as much as possible, with that of the mercury-in-glass
thermometer, provided that the temperature read from the record
shall not be higher than that of the mercury-in-glass thermometer.
6.4.1.1.2.4 The recorder is equipped with a steam controller and is composed
of a temperature recording controller. In addition to the vertical
kettle device temperature record control device, the other
pipelines of temperature recorder should be connected with the
mercury thermometer temperature sensor adjacent device.
6.4.1.1.2.5 Vertical retort, temperature record controller shall be installed
under the basket at the bottom of sterilizer, and shall avoid steam
spraying directly to the temperature sensor.
6.4.1.1.2.6 Horizontal retort, the temperature sensor should be installed
between the water surface of the kettle and the center of the kettle
to prevent steam from directly touching the temperature sensor.
6.4.1.1.2.7 Measures to prevent unauthorized access shall be in place to
prevent unauthorized personnel or sterilizing operators from
arbitrary changing the temperature recorder settings. Measures
may include using a lock or posting warning signs indicating
“Authorized Personnel Only”.
6.4.1.1.2.8 The pneumatic temperature controller shall be equipped with an
effective filtering system to ensure the air is clean and dry.
6.4.1.1.3 Pressure gauge
6.4.1.1.3.1 Each sterilizer shall be equipped with at least one pressure gauge
on a coiled tube. The gauge dial shall be at least 4½ inches in
diameter, with reading ranging from 0-3.5kg/cm2. Each span of
scale mark shall be 0.1kg/cm2.
6.4.1.1.3.2 A pressure gauge shall be calibrated by an accredited
organization at least once a year before use. Pressure shall not be
a reference parameter for the sterilization condition.
6.4.1.1.3.3 Each sterilizer shall be equipped with an adjustable pressure
relief valve or pressure control valve on the overflow pipe to
prevent the pressure in the tank from increasing drastically when
TQF-PCS-016
TQF Management Technical Specifications—Certification Regulation Ver. 2.0
22 / 66 ©Taiwan Quality Food Association
[Canned Food]
the inlet valve is fully opened.
6.4.1.1.4 Steam controller
6.4.1.1.4.1 An automatic steam controller shall be equipped to maintain the
correct sterilization temperature of a sterilizer. An integrated
temperature recorder and steam controller is also acceptable.
6.4.1.1.4.2 When using a hand-operation instead of automatic steam
controller, during the sterilizing process shall ensure to meet the
sterilizing operation requirement and recorded.
6.4.1.1.5 Steam inlet pipe
6.4.1.1.5.1 The diameter of the smallest orifice (such as inlet pipes, valves
and fittings) shall not be less than 1 inch (approximately 25mm),
in other words, the internal diameter shall be greater than 26 mm
(cross sectional area 530mm2). The information of diameters,
apertures and number of holes should refer to the related
regulations which is announced in “The regulation on Good
Hygiene Practice for Food, GHP“, TFDA. The steam inlet of
Vertical retort shall be located at the central line of the bottom.
6.4.1.1.5.2 If the length of the horizontal kettle is within 9 meters
(approximately 30 feet), the inlet of the kettle shall be at the
longitudinal centerline of the tank bottom. If the length of the
kettle exceeds 9 meters, two or more steam inlets shall be
installed. The inlet steam inlet device shall distribute the heat
within the kettle evenly.
6.4.1.1.6 Introduction of steam
6.4.1.1.6.1 Steam shall be introduced from the bottom of retort to equalize
the heat distribution within the retort.
6.4.1.1.6.2 Vertical retorts may use any method that has been approved to
average the heat distribution
6.4.1.1.6.3 The steam turbine of the horizontal retort shall extend to the full
length of the bottom of the retort, and the steam injection holes
shall be evenly distributed above the steam injection pipe.
6.4.1.1.7 Steam distribution pipes and steam nozzles
6.4.1.1.7.1 The size of steam distribution pipes shall not be larger than the
steam inlet pipe and shall not be less than one inch in diameter.
The steam distribution pipes of horizontal sterilizers shall extend
across the total length of the sterilizer and have three rows of
TQF-PCS-016
TQF Management Technical Specifications—Certification Regulation Ver. 2.0
23 / 66 ©Taiwan Quality Food Association
[Canned Food]
nozzles, including one at the center top and two at 45°
intersecting the top center line. Nozzles of each of these two rows
shall be alternated.
6.4.1.1.7.2 For vertical sterilizers, nozzles shall be aligned on the overhead
or on both sides of the vertical sterilizers.
6.4.1.1.7.3 The number of nozzles shall ensure that the total cross sectional
area of the nozzles of a vertical or a horizontal sterilizer has
minimum of 1.5 to 2 times the cross sectional area of the inlet
steam pipe.
6.4.1.1.8 Vapor release valve
6.4.1.1.8.1 The cross section diameter of the valve shall at least be ⅛ inch
(except for valves installed in the temperature well). Vapor
release valves shall be installed in a location where operators can
observe their operation and be fully opened at all times during the
sterilization process to maintain good steam circulation.
6.4.1.1.8.2 Vapor release valves for a horizontal sterilizer shall be installed
within 12 inches away from both ends of the sterilizer’s top, and
the interval between valves shall be within 8 feet.
6.4.1.1.8.3 Vapor release valves for a vertical sterilizer shall be installed on
top of the lid. When installing vapor release valves in other
positions, manufacturers shall submit thermal distribution data to
prove that the air inside the sterilizer is completely drained and
steam circulation is good.
6.4.1.1.8.4 All vapor release valves shall be installed in a manner so that
operators can ensure their functions throughout the sterilization
process.
6.4.1.1.9 Sterilization baskets and container racks shall be made with metal
bars, metal mesh plates, or other suitable materials. When using metal
mesh plates, the mesh diameter shall be equivalent to 1 inch, the mesh
interval shall be 2 inches apart from center to center, or the total mesh
cross sectional area shall not be smaller than 36% of the plate area.
When partitions are used on each level of containers, the mesh size of
the partition shall be the same as that of the metal mesh plate. During
the sterilization process, containers shall be arranged in a manner
complying with the sterilization process specified on the procedure
TQF-PCS-016
TQF Management Technical Specifications—Certification Regulation Ver. 2.0
24 / 66 ©Taiwan Quality Food Association
[Canned Food]
(exempted when none).
6.4.1.1.10 Basket frame support
No sterilizer baffle shall be installed at the bottom of a static
sterilizer. Horizontal sterilizers shall be equipped with basket frame
supports to allow there is a 4cm (1.5 inch) gap between the wall of
sterilizer and basket frame.
6.4.1.1.11 Pressure air pipes
Pressure air pipes for pressure cooling shall be equipped with an
appropriate type of valves. Valve specifications, such as globe valves
or ball valves, shall be the same as that of water intake pipes to
prevent air from infiltrating into the sterilizer during the sterilization
process.
6.4.1.1.12 Water inlet pipes, drainage pipes, drainage valves, and safety valve
water inlet pipes shall be equipped with an appropriate type of valve,
such as globe valves or ball valves, to prevent cold water from
leaking into the sterilizer during the sterilization process. In addition,
gate valves shall not be used on water inlet pipes. Water shall enter
the sterilizer from the top to ensure even cooling of cans inside the
sterilizer. The size of drainage pipes shall not be smaller than that of
the water inlet pipes. Filters shall be installed on the drains. Each
sterilizer shall be equipped with a safety valve whose diameter shall
not be smaller than that of the steam inlet pipe.
6.4.1.1.13 Main steam pipe
Main steam pipes shall be appropriately constructed and equipped
with a water discharge valve. A pressure gauge with correct
indications that can be clearly read by operators shall be installed on
the end of the main steam pipes in the sterilization zone. The pressure
of the main steam pipes shall be maintained at over 6kg/cm2.
6.4.1.1.14 Air release pipelines
6.4.1.1.14.1 An air release device shall be designed to ensure the release of
air inside a sterilizer before sterilization begins.
6.4.1.1.14.2 The cross sectional area of the pipe diameter shall be larger than
that of the steam inlet pipe. Valves shall be gate type, plug type,
or other types appropriate to quickly fully opening the air
release valve. In addition, the air release pipe shall not be
directly connected to a closed pipeline and shall remain at
TQF-PCS-016
TQF Management Technical Specifications—Certification Regulation Ver. 2.0
25 / 66 ©Taiwan Quality Food Association
[Canned Food]
normal open position.
6.4.1.1.14.3 Air release pipes shall be installed atop horizontal sterilizers or
on the lid of a vertical sterilizer in the opposite position of the
steam intake pipe.
6.4.1.1.14.4 The outlet of an air release pipe shall be open to atmosphere.
Right angle bends or other conditions that will hamper airflow
shall be prevented in the piping. An air release pipe shall be
below 46cm long, and can transport the steam off the
sterilization zone with an air release pipeline that have a sizes
larger than the air release pipe and with a condensed water
outlet at the bottom.
6.4.1.1.14.5 The cross sectional area of an air release main pipe shall be
larger than the total cross sectional area of the connected air
outlets or an air release pipeline.
6.4.1.1.14.6 When connecting air release pipes of several static sterilizers to
one air release master pipeline, the cross sectional area of the air
release master pipeline shall be larger than the total cross
sectional area of the connected air release pipes and no valve
shall be installed on the master pipeline.
6.4.1.1.14.7 Most importantly, the sterilization time shall not be calculated
before the air release procedure is completed or before the reach
of temperature required.
6.4.1.2 Static pressurized hot water sterilizers
6.4.1.2.1 Mercury-in-glass thermometer
6.4.1.2.1.1 Each sterilizer shall be equipped at least one mercury-in-glass
thermometer with a total length of the scale marks at least 7
inches long, and a maximum of 55 scale division, with accuracy
as low as 0.5°C.
6.4.1.2.1.2 A mercury-in-glass-thermometer shall be calibrated, by an
accredited organization at least once a year, before use. The latest
calibration date and respective calibration data shall be labeled on
the thermometer.
6.4.1.2.1.3 The mercury line in the glass shall not be separated and the
thermometer shall be installed in a position where the sterilizer
operators can correctly reading the scale.
6.4.1.2.1.4 During the sterilization process, the bulb shall be immersed
TQF-PCS-016
TQF Management Technical Specifications—Certification Regulation Ver. 2.0
26 / 66 ©Taiwan Quality Food Association
[Canned Food]
under water by at least 50mm (2 inches). The temperature
indicated by the mercury-in-glass thermometer shall be used as
the base sterilization temperature, and shall not be substituted
by the temperature from the automatic temperature recorder.
6.4.1.2.1.5 For horizontal sterilizers, a mercury-in-glass thermometer shall
be installed at the center on the side of the sterilizer.
6.4.1.2.2 Temperature recorder
Same as static steam sterilizers.
6.4.1.2.3 Pressure gauge
Same as static steam sterilizers.
6.4.1.2.4 Steam controller
Same as static steam sterilizers.
6.4.1.2.5 Sterilization baskets and container racks arrangement
Same as static steam sterilizers.
6.4.1.2.6 Steam pipes and steam nozzles
Same as static steam sterilizers. Nozzles of a vertical sterilization
shall be aligned in a row, facing downward at a degree of 15°.
Nozzles shall not be clogged.
6.4.1.2.7 Basket frame supports
Same as static steam sterilizers.
6.4.1.2.8 Drainage valves
Same as static steam sterilizers.
6.4.1.2.9 Water level gauge
Each sterilizer shall be equipped with one water level gauge for
reading the water level inside the sterilizer, during the heating,
sterilizing, and cooling processes. The water inside the sterilizer shall
cover up the containers at the top level (4-6 inches is recommended).
Operators shall check and record the water level before sterilization
and at any time during the sterilization process.
6.4.1.2.10 Supply and control of air
6.4.1.2.10.1 Air pressure control shall be achieved by the automatic pressure
controller (Actuator). Air shall be supplied at an appropriate
pressure and flow. Air pipes shall be equipped with a check
valve to prevent water in the sterilizer from flowing back into
the pipe. During the heating, sterilizing, and cooling processes,
continuous air or water circulation shall be maintained. Air shall
TQF-PCS-016
TQF Management Technical Specifications—Certification Regulation Ver. 2.0
27 / 66 ©Taiwan Quality Food Association
[Canned Food]
be used to facilitate air circulation. Compressed air shall be
input through the steam inlet pipeline between the steam inlet
and the steam control valve at the bottom of the sterilizer.
6.4.1.2.10.2 For air pressurized cooling air pipes, the valve of the pipe shall
be equipped with a ball valve or ball plug valve. Gate valves
should not be used.
6.4.1.2.10.3 When automatic pressure controller operation is not carried out
but hand-operation, the pressure shall be manually controlled to
ensure compliance with the sterilizing operating conditions.
6.4.1.2.11 Water circulation system
Nozzles on the water spreading pipe shall be evenly distributed. The
total cross sectional area of nozzles shall be smaller than the cross
sectional area of the output pipe of the pump water. Filters shall be
installed at the outlet of pump at the bottom of the sterilizer to prevent
debris from entering the water circulation system. A warning
indicator shall be equipped on the circulation pump to alert operators
when the pump stops.
6.4.1.2.12 Supply of cooling water
6.4.1.2.12.1 Check valves shall be installed along the cooling water pipeline.
Cooling water for horizontal sterilizers shall be introduced from
inlet side of the circulation pump. Cooling water for vertical
sterilizers shall be input from in between of the top water level
and containers on the top level (should be 2 inches under the
overflow pipe).
6.4.1.2.12.2 When cooling is carried out in a retort, the horizontal retort shall
be filled with water from the spray pipe on the top. The vertical
retort shall be filled with water from spray ring on the top. The
water spray pipe of the horizontal retort shall have three or more
rows of water spray holes to spray water downwards (when using
three rows of water spray holes, the central row of ones shall be
vertically downward, and the other two rows shall be at an angle
of 45 degrees with it).
6.4.1.2.12.3 The inlet pipe shall be fitted with a ball valve or ball plug valve.
Gate valves shall not be used.
6.4.1.2.13 Headspace inside sterilizers
An adequate head space between the top of a sterilizer and water level
TQF-PCS-016
TQF Management Technical Specifications—Certification Regulation Ver. 2.0
28 / 66 ©Taiwan Quality Food Association
[Canned Food]
shall be maintained (at least 4 inches is recommended) to facilitate
internal pressure control.
6.4.2 Rotary sterilizers
6.4.2.1 Discontinuous steam pressurized sterilizers
6.4.2.1.1 Mercury-in-glass thermometer
Same as static steam sterilizers.
6.4.2.1.2 Temperature recorder
Same as static steam sterilizers.
6.4.2.1.3 Pressure gauge
Same as static steam sterilizers.
6.4.2.1.4 Steam controller
Same as static steam sterilizers.
6.4.2.1.5 Vapor release valve
The valve shall at least be ⅛ inch (except for valves installed in the
temperature well). the installation position shall be within 20
centimeters (about 8 miles) from the ends of the centerline of the
kettle top, and the distance between the bolt and the spigot shall not
be more than 240 cm (approximately 8 miles), and should be able to
make operators aware of its operating conditions, and throughout the
sterilization process must be kept fully open to maintain a good steam
cycle.
6.4.2.1.6 Air release and condensed water discharge
Air inside sterilizers shall be vented before sterilizing. When
sterilization begins, open the drain valve or drain plug for adequate
time to drain out the condensed water.
6.4.2.1.7 RPMs of sterilizers
Rotations per minute (RPMs) shall comply with the sterilization
requirements. Measures shall be taken to prevent unauthorized access
to or the designated operators from making arbitrary changes of the
RPM settings. It may include using a lock or posting labels such as
“Authorized Personnel Only”. Every time when can sterilization, the
TQF-PCS-016
TQF Management Technical Specifications—Certification Regulation Ver. 2.0
29 / 66 ©Taiwan Quality Food Association
[Canned Food]
RPMs of sterilizers and the period shall be recorded.
6.4.2.2 Discontinuous hot water pressurized sterilizers
6.4.2.2.1 Mercury-in-glass thermometer
Same as static steam sterilizers.
6.4.2.2.2 Temperature recorder
Same as static steam sterilizers.
6.4.2.2.3 Pressure gauge
Same as static steam sterilizers.
6.4.2.2.4 Steam controller
Same as static steam sterilizers.
6.4.2.2.5 Supply and control of air
Same as static hot water sterilizers.
6.4.2.2.6 RPMs of sterilizers
Same as discontinuous steam pressurized sterilizers.
6.4.3 Aseptic processing and packaging systems
6.4.3.1 Product sterilization
6.4.3.1.1 Temperature display devices
6.4.3.1.1.1 Each product sterilization unit shall be equipped with at least one
mercury-in-glass thermometer or other temperature display device
(e.g. thermocouple recorder). A mercury-in-glass thermometer
shall be equipped with scale marks with accuracy as low as 0.5°C,
a total length of the scale marks of at least 7 inches long, and a
maximum of 55 scale divisions.
6.4.3.1.1.2 Every thermometer shall indicate the date of least calibration. The
thermometer shall be calibrated by an accredited organization at
least once a year and qualified before use.
6.4.3.1.1.3 The mercury line in glass shall not be separated and the
thermometer shall be installed in a position where the sterilizer
operators can correctly read the scale.
6.4.3.1.1.4 During the sterilization process, the temperature indicated by the
mercury-in-glass thermometer or temperature display device shall
be used as the sterilization temperature, and shall not be substituted
by the temperature indicated on the automatic temperature
recorder.
6.4.3.1.1.5 For non-use mercury thermometers, the sterilization temperature
shall be based on the indicated temperature of the temperature
TQF-PCS-016
TQF Management Technical Specifications—Certification Regulation Ver. 2.0
30 / 66 ©Taiwan Quality Food Association
[Canned Food]
indicating device. The temperature measurement shall be between
the outlet of the product sterilizing holding pipe and the inlet of the
cooling pipe, and the temperature of the product can be directly
sensed.
6.4.3.1.2 Temperature recorder
6.4.3.1.2.1 Each product sterilization unit shall be equipped with temperature
recorders that can accurately record the temperature. A recorder
shall be installed at the outlet of a constant temperature insulation
pipe, in between of the thermostat insulated pipe and cooling
device inlet, which can directly detect product temperature.
6.4.3.1.2.2 The number of scale marks per inch for a 10°C range of
sterilization temperature recorder chart shall not exceed 25°C in
the recorder grid, and the scale division of a 5°C range of
sterilization temperature recorder chart shall not exceed 1°C. The
temperature indication of the recorder shall be adjusted in
consistent with that of the mercury-in-glass thermometer, provided
that the temperature read from the record shall not be higher than
that of the mercury-in-glass thermometer.
6.4.3.1.2.3 Measures to prevent unauthorized access shall be in place to
prevent unauthorized personnel or the sterilizing operators from
arbitrary changing the temperature recorder settings. Measures
may include using a lock or posting warning sign indicating such
as “Authorized Personnel Only”.
6.4.3.1.3 Temperature controller
An accurate temperature control shall be equipped at the outlet of the
sterilization unit to ensure products are maintained at the designated
sterilization temperature. The scale division of a 5°C range of
sterilization temperature recorder chart shall not exceed 1°C.
6.4.3.1.4 Product heat exchanger
A heat exchanger shall be designed, operated, and controlled to
ensure a positive pressure of sterilized products that is greater than
that of cold unsterilized products in the heat exchanger to prevent the
latter from infiltrating into the former.
6.4.3.1.5 Differential pressure control recorder
A differential pressure control record shall be equipped at the outlet
of sterilized products and the outlet of unsterilized products of a heat
TQF-PCS-016
TQF Management Technical Specifications—Certification Regulation Ver. 2.0
31 / 66 ©Taiwan Quality Food Association
[Canned Food]
exchanger. The scale marks per inch shall not exceed 20psi, with
accuracy up to 2psi for each mark division. Differential pressure
control recorders should be calibrated by accredited organizations
before use and calibrated once every three months.
6.4.3.1.6 Quantitative pump
A quantitative pump shall be installed in front of the thermostat-
insulated pipe to ensure product flow velocity specified in the
sterilization requirements. Measures shall be in place to prevent
unauthorized access or the sterilizing operators from arbitrary
changing the settings. Measures may include using a lock or posting
warning sign indicating such as “Authorized Personnel Only”.
6.4.3.1.7 Thermostat insulated pipe
A pipe shall be designed to ensure continuously retention of products
in the pipe for an adequate time and comply with the sterilization
requirements. No heating devices of any kind shall be installed
between the inlet and outlet of the pipe. The pipe shall be inclined at
a minimum gradient of 0.25in/ft. (2.1cm/m).
6.4.3.1.8 Diversion system
A diverter shall be installed at the product pipelines between a cooler
and a product filler/aseptic storage tank. The system shall be designed
to automatically divert products away from a filler or aseptic storage
tank, and an alarm shall be installed once the temperature of the
thermostat insulated pipe or the differential pressure of the heat
exchange is lower than the specified sterilizing condition.
6.4.3.1.9 Subsequent equipment after the thermostat insulated pipe
Equipment installed behind the thermostat insulated pipe, including
product cooling device, aseptic storage tank, or other equipment that
containing rotating shafts or valve handles, and equipment
connections which with potential threats of microbial intrusion shall
be equipped with a steam seal or other blocking devices, and
appropriate methods for operators to monitor those operation shall be
in place.
6.4.3.1.10 Handling of temperature drop of the thermostat insulated pipe
When the temperature of a thermostat insulated pipe drops below the
specified sterilizing condition, the operators shall divert products off
the filler or aseptic storage tank. When under-sterilized products have
TQF-PCS-016
TQF Management Technical Specifications—Certification Regulation Ver. 2.0
32 / 66 ©Taiwan Quality Food Association
[Canned Food]
been filled into the containers, operators shall segregate them from
the sterilized products and handle them in accordance with the
“Sterilization Anomaly Handling Procedure”. The products within
and after the thermostat insulated pipe that have been affected by the
temperature drop shall be re-sterilized until meeting the commercially
sterilization standard before diverting the products to the filler or
aseptic storage tank.
6.4.3.1.11 Handing of differential pressure anomaly of the heat exchanger
When the differential pressure between the sterilized products and
unsterilized products is below 1psi, the operators shall divert products
off the filler or aseptic storage tank. When under-sterilized products
have been filled into containers, it shall be segregated from the
sterilized products and handled in accordance with the “Sterilization
Anomaly Handling Procedure”. A corrective actions shall be taken for
the differential pressure variation and sterilizing the affected products
until they meet the commercially sterilization standard before re-
starting of sterilization and filling operation.
6.4.3.1.12 Handling of anomaly in aseptic storage thank
When the aseptic storage tank occurs anomaly on its maintain of
positive pressure or other protection measures used, which may cause
deficiency of the aseptic condition of the storage tank, all potentially
affected products shall be eliminated, and the aseptic storage shall be
re-sterilized until it meets the commercially sterilization standard
before re-starting of product sterilization and filling operation.
6.4.3.2 Container sterilization and filling and seaming of product
6.4.3.2.1 Time for container sterilization
Appropriate measures shall be applied to control container
sterilization conditions (germicide concentration, sterilization time,
and sterilization speed) and comply the designated level(s) of
sterilization. A speed regulator shall be equipped with measures to
prevent unauthorized access or the sterilizing operators from arbitrary
changing settings. Measures may include using a lock or posting
warning sign indicating such as “Authorized Personnel Only”.
6.4.3.2.2 Handing of anomaly
When filling conditions are below the requirements designated by the
sterilization conditions, filling shall be stopped or appropriate
TQF-PCS-016
TQF Management Technical Specifications—Certification Regulation Ver. 2.0
33 / 66 ©Taiwan Quality Food Association
[Canned Food]
methods shall be used to segregate filled products, such as diverting
products off the filler or blocking containers from entering the filler
with a diversion system. The finished products that are not complying
with the sterilization standard shall be segregated from those
sterilized products and handled in accordance with the “Sterilization
Anomaly Handling Procedure”.
6.4.4 Sterilization records
6.4.4.1 At the binging of sterilization and during the process, at least once every
hour to test and record the following items.
6.4.4.1.1 The temperature presented by the temperature indicator and
temperature recording device at the outlet of the product sterilizing
maintaining pipe.
6.4.4.1.2 The pressure on the both end-side of heating exchange device of a
product.
6.4.4.1.3 Product flow rate (can be counted using quantitative or filling
packaging methods).
6.4.4.1.4 Aseptic air pressure in sterile storage tanks or other measures to
maintain sterility.
6.4.4.1.5 Inspection of steam seals or other blocking devices on equipment and
piping to prevent the ingress of microorganisms.
6.4.4.2 Recording device: containers and lidding materials of sterilization system,
product filling and sealing systems, shall be capable of performing the
required degree of sterilization continuously. If necessary, automatic
recording devices shall be used to record the flow rate, temperature,
concentration or other factor. If the containers are sterilized in batches, the
sterilization conditions should be recorded.
6.4.5 If the sterilization equipment differs from the above descriptions, the canned
food factory shall submit proof of the test of even thermal distribution for its
sterilization equipment, which is issued by a government recognized entity.
6.5 Quality control equipment
6.5.1 The food factory shall have adequate testing equipment for the routine
QC testing and inspection to determinate the quality of raw materials,
semi-finished and finished products. When necessary, testing and
inspection shall be performed by an approved contractors or institutes
when suppliers do not possess the equipment on site.
6.5.2 The food plants shall equip with specified testing instruments and apparatus
TQF-PCS-016
TQF Management Technical Specifications—Certification Regulation Ver. 2.0
34 / 66 ©Taiwan Quality Food Association
[Canned Food]
which is appropriate for analyzing the ingredients, materials, semi-finished
products, and finished products:
6.5.2.1 Analytical scale (with maximum sensitivity at 0.1 mg).
6.5.2.2 pH meter (with sensitivity down to two decimals).
6.5.2.3 Brix hydrometer.
6.5.2.4 Incubator.
6.5.2.5 Microbial test equipment.
6.5.2.6 Residual chlorine analyzer.
6.5.2.7 Can seam micrometer.
6.5.2.8 Can vacuum or pressure testing device.
6.5.2.9 Can vacuum leak testing device.
6.5.2.10 Tensile strength tester (required for retort pouch packaged food factories).
6.5.2.11 Pouch residual air analyzer (required for retort pouch food packaged
factories).
6.6 Establishment of sterilization conditions
6.6.1 LACF sterilization conditions shall be established by a qualified organization
that having suitable equipment and capacity, and is recognized by the
government. Data for calculating, evaluating, and validating sterilization
conditions shall be set in order and properly retained by the organization
during the period of using such sterilization conditions.
6.6.2 The sterilization conditions of acid canned foods shall be established by those
who have been qualified by the training course on sterilization technology
management that offered by a government recognized organization, and who
have manufacturing experience of acid canned foods.
6.6.3 Sterilization conditions shall be established in consideration of food properties;
preparation and processing methods; shape and size of foods; liquid filled;
solid-to-liquid ratio; container specifications; and the species, habits, and total
contaminated number of putrefactive bacteria; and the critical factors for
sterilizing.
6.6.4 The setting of sterilizing conditions of every different product, shall be
presented near to the sterilization machines or placed in a place where is easily
accessible to sterilizing operation workers.
6.6.5 The management of important factors of sterilization
6.6.5.1 The important control factors for the setting of sterilization conditions
should be determined and recorded at a sufficient frequency to ensure that
TQF-PCS-016
TQF Management Technical Specifications—Certification Regulation Ver. 2.0
35 / 66 ©Taiwan Quality Food Association
[Canned Food]
all important control factors are within the set limits.
6.6.5.2 All heat distribution data, including exhaust gas, temperature rising time
and final temperature, shall be tested by the central health welfare authority
approved organizations which have the heat pasteurization expertise of low
acid canned foods.
6.6.5.3 In the sterilization conditions, when the highest loading volume or solid
volume is set, it shall be measured and recorded at an appropriate
frequency to ensure that the solids content of the product does not exceed
the set volume.
6.6.5.4 In the sterilization conditions, when setting the degree of vacuum, the
upper gap, the viscosity, etc., it should be checked and recorded at an
appropriate frequency to ensure conforming to the intended sterilization
conditions.
6.6.5.5 Non-continuous rotary retort steam pressurization and sterilization shall set
the rotation speed of the retort, the upper gap (or the highest loading
capacity) inside the tank, the viscosity and the arrangement of the cans as
important factors.
7 Organization and Personnel
7.1 Organization and duties
7.1.1 The food factory shall have and disclose the organizational structure
and its responsibilities related to food safety activities, including the
specialist in charge for food safety and quality and their authority to
supervise and carry out the tasks. Personnel in charge of the
management of the production, quality assurance, sanitation, food
safety and other departments shall be assigned as a specialist to
supervise, monitor or perform their respective functions and activities.
7.1.2 Production specialist are in charge of raw material handling, processing
and packaging operations. Quality assurance supervisor are responsible
for the establishment of quality standards and sampling requirements,
testing and traceability management of raw materials, intermediate and
finished products. Sanitation and hygiene supervisor are responsible for
the sanitary aspects of the internal and external environment, premises
and facilities, personnel hygiene, production and cleaning operation and
personnel hygiene training. The food safety control specialist is
TQF-PCS-016
TQF Management Technical Specifications—Certification Regulation Ver. 2.0
36 / 66 ©Taiwan Quality Food Association
[Canned Food]
responsible for the implementation and maintenance of the food safety
control program based on the HACCP principles and the TQF
specifications and product certification scope; While the specialist
responsible for labor safety management are in charge of the food plant
safety and defense.
7.1.3 A committee to promote the TQF system shall be established. The
committee should consist of at least three person from senior executives
and department specialists, in which the senior executives or their
designees are necessary members and are responsible of identifying the
food safety management system and verifying the HACCP plan of TQF
product certification, and to formulate, implement and manage relevant
records; in the means time, the committee is also responsible for
planning, reviewing, supervising and assessing the quality management
of the matters concerning the food plant’s quality management. The
senior executives shall supervise the implementation and maintenance
of food safety and provide sufficient manpower and resources to
achieve the goal of food safety management and to ensure that effective
and sustainable resources are continuously provided to meet the
operation, maintenance and improvement of the food safety
management system.
7.1.4 The Quality Assurance Department shall be independent from the other
departments and shall have full authority to manage quality assurance
tasks. The person in charge shall have the authority to stop production
or product release.
7.1.5 The Quality Assurance Department shall designate a food testing and
inspection personnel to analyze and test the general and sanitary-
hygienic quality of the products.
7.1.6 A working group for sanitation and hygiene management (which can be
incorporated into the relevant committees that implement the TQF
system) shall be established, comprising of the specialist of sanitation
management and personnel of other departments. The group shall be
responsible for planning, evaluating, instructing and monitoring, and
auditing sanitation and hygiene matters of the whole plant. The name of
the person should be clearly marked based on the appropriate
workplace.
7.1.7 The person in charge of the production and the person in charge of the
TQF-PCS-016
TQF Management Technical Specifications—Certification Regulation Ver. 2.0
37 / 66 ©Taiwan Quality Food Association
[Canned Food]
quality control area shall not be the same. However, personnel of other
departments are allowed to share interdepartmental responsibilities.
7.2 Personnel and qualification
7.2.1 The person in charge of production, quality control, sanitation management
and safety management shall be a college graduate from related fields, or have
a high school or vocational education diploma, or a higher degree with at least
four years experiences in food manufacturing.
7.2.2 Food testing personnel should have passed the government-certified
examination for food testing technicians or be graduated from related fields at
university degree. If the personnel is graduated from high school, vocational
education or unrelated university degree, the personnel shall have gone
through government-approved professional training (i.e., food testing training
course), and hold a certificate of completion.
7.2.3 The person in charge of a department and the technical assistants shall
receive, within three years of employment, professional pre-
employment or on-the-job training by attending the training courses
organized by government entities, research institutions or private
training organizations and hold a certificate of completion.
7.2.4 Food manufacturing factories which is specified in the categories of “Act
Governing Food Safety and Sanitation” shall be equipped with sanitation
management personnel, who are with qualifications and duty descriptions
complied with the “Regulations Governing the Establishment of the Sanitation
Control Personnel of Food Manufacturing Factory”.
7.2.5 All category of specialized technical personnel shall comply with the relevant
laws and regulations stipulated by the central competent authority.
7.2.6 At least one member of the related committee implementing TQF Technical
Specification shall be a certified food technologist or being graduated from a
food related department with a university degree, and have attended and
passed the training courses in Good Hygiene Practice (GHP) and Hazard
Analysis and Critical Control Points (HACCP) organized by training agencies
approved by the central competent authority.
7.2.7 A canned beverage factory shall be equipped with management personnel for
can seaming and sterilization in accordance with following regulations:
7.2.7.1 Container seaming mechanics taking charge of the adjustment,
maintenance, repair and recording of seaming machines must graduate
from at least a junior high school or an elementary school with three years
TQF-PCS-016
TQF Management Technical Specifications—Certification Regulation Ver. 2.0
38 / 66 ©Taiwan Quality Food Association
[Canned Food]
of can seaming experience and pass accredited container seaming
technology training.
7.2.7.2 Sterilization equipment operators taking charge of the operation, recording,
and maintenance of sterilization equipment must at least graduate from
junior high schools or equivalent and pass accredited sterilization
equipment operation training.
7.2.7.3 Sterilization technical management personnel taking charge of production
management of the beverage sterilization system must be a university
graduate or equivalent (senior high schools, senior high schools of
industry, senior high schools of agriculture, and senior high schools of
commerce with over three years of practical work experience) and pass
accredited sterilization technology management training.
7.3 Education and training
7.3.1 New employees should receive appropriate education and training so
that their capacity of execution are in line with the production,
sanitation, hygiene and quality management requirements. Employees
should set annual training plans to be carry out and documented. The
annual training program should include on-site and off-site training
courses, and the effectivity in enhancing the management and
implementation capacity of the TQF certification shall be considered
during its planning.
7.3.2 Training on GHP and HACCP shall be conducted periodically (even
inside the factory) for employees engaged in food manufacturing and
related operations.
7.3.3 Personnel of the Quality Assurance Committee responsible for the food
safety management system shall, at least once every three years, be
subjected to HACCP related professional training, seminars,
workshops, meetings or other courses approved by the central
competent authority, with a cumulative training duration of more than
12 hours.
7.3.4 All departmental managers shall be committed to their responsibilities,
lead by example, and supervise and educate their staff to follow the
established operating procedures or rules.
7.3.5 Employees are required to obtain a certificate of participation in a
hygiene seminar or training course conducted by the competent health
TQF-PCS-016
TQF Management Technical Specifications—Certification Regulation Ver. 2.0
39 / 66 ©Taiwan Quality Food Association
[Canned Food]
authority or approved related institution.
8 Sanitation and Hygiene Management
8.1 Establishment and implementation of the “Standard Operation Procedure for
Sanitation Management”.
8.1.1 The food plant shall establish standards for sanitation management as the basis
for sanitation and hygienic management and assessment, which shall include
the provisions of this chapter, even when amendments are made.
8.1.2 A sanitation inspection plan shall be established with specification of
schedules and items to be checked, and a sanitation management personnel
shall be designated to carry out the sanitation inspection in according to the
plan to confirm the sanitation condition of the specific day and that it was
actually carried out and recorded.
8.1.3 Pests and vector control measures should be developed, implemented and
documented.
8.2 Environmental sanitation management
8.2.1 Roads adjacent to the factory, along with passages ways and garden inside the
factory shall always be kept clean. The open ground inside the plant shall be
kept in good state of repair without damage, accumulation of water and no
dust.
8.2.2 Vegetation inside the plant shall be trimmed periodically, and accumulation
and storage of unnecessary equipment and articles are prohibited to prevent
pests from entering the facility.
8.2.3 Premises and plant facilities shall be kept in good sanitary condition and
properly maintained to protect against the contamination of food.
8.2.4 Gutters shall be kept unobstructed, with no accumulation of sludge, and waste
water shall be properly addressed and treated.
8.3 Plant facilities sanitation management
8.3.1 Sanitary standards and sanitation management regulations for operation zones
shall be established in accordance with the cleanliness classification specified
in 5.2.
8.3.2 Sanitary standards and sanitation management regulations for factory
equipment shall be established and exactly implemented in accordance with
TQF-PCS-016
TQF Management Technical Specifications—Certification Regulation Ver. 2.0
40 / 66 ©Taiwan Quality Food Association
[Canned Food]
the regulations outside of the factory.
8.3.3 Facilities inside the plant shall be kept clean and in good state of maintenance
at all times. When the roof, ceiling and walls of the factory are damaged, they
shall be repaired immediately, and the ground and drainage facilities shall not
be damaged or stagnant.
8.3.4 Raw material handling areas, processing and preparation areas, and toilets
shall be cleaned daily (including floors, drains, and walls) before production
and disinfected when necessary.
8.3.5 Steam generated during the operation shall not be allowed to remain inside the
factory for a long period of time and shall be vented out through effective
facilities.
8.3.6 Production and storage areas shall take effective measures to prevent
or eliminate pests and vectors, such as screens, air curtain, fences or
insect traps.
8.3.7 The surface of lighting and pipes shall be kept clean at all times and be swept
or cleaned periodically.
8.3.8 Cool storage shall be sorted, set in order, and kept clean at all times, and
conditions affecting food sanitation such as pooling on floors and moldy walls
shall be prevented.
8.3.9 No pest or vector or traces of it shall be found inside the plant. However, when
present the source shall be eliminated using methods that do not cause
contamination of food, food contact surfaces and inner packaging material
(pesticides shall be avoided).
8.3.10 Raw materials, inner packaging materials or other unnecessary articles that are
not being immediately used shall not be keep in the controlled operation area.
8.3.11 Equipment and tools for cleaning and sanitizing shall be stored at specific
designated location.
8.3.12 Do not place or store any substance in the processing area that pose a risk to
food safety.
8.3.13 Periodical cleaning and daily inspection of chlorination treatment (prior to
production), and regular monitoring to avoid contamination of processing
water quality are recommended if reservoirs (tower or pool) are used. When
using non-potable water, a personnel shall be designated in charge of checking
the residual chlorine and pH value every day, and at least once a year a
government recognized inspection agency shall be sent to ensure that water
meets potable water quality standards (with exception of boiler water, cooling
TQF-PCS-016
TQF Management Technical Specifications—Certification Regulation Ver. 2.0
41 / 66 ©Taiwan Quality Food Association
[Canned Food]
water for refrigeration compressor or evaporator, or floor cleaning water etc.).
8.4 Machinery and equipment sanitation management
8.4.1 Equipment and utensils for manufacture, processing, formulation, packaging,
and storage shall be cleaned and sterilized periodically. The “machinery and
equipment sanitation management standards and regulations” shall be
established and exactly implemented. The cleaning and sterilization of utensils
and equipment shall not contaminate foods, food contact surfaces, and food
interior packaging materials.
8.4.2 Every day after manufacturing ends, sugar (salt) liquid barrels, sugar (salt)
liquid filters, sanitation pumps, rubber tubes, plastic hoses, and all kinds of
gauges and containers shall be disassembled (except for CIP) and thoroughly
cleaned.
8.4.3 When water needs to be disposed from the equipment, it shall be design to
properly collect the water and direct it to the drainage system to avoid any
contamination.
8.4.4 Cleaning agents or disinfectants used in the cleaning operation shall
not contaminate food, food contact surfaces and inner packaging
materials.
8.4.5 Juice extractors, fine filters, and centrifuges shall be disassembled and washed
immediately after use.
8.4.6 Fillers shall be thoroughly washed, and the inlet shall be disinfected with
disinfectants such as chlorine after washing.
8.4.7 After using a seaming machine, parts and blind spots, such as the chuck,
seaming roll, and lifter, and other areas that are prone to contamination shall
be washed thoroughly.
8.4.8 Container cleaning equipment, such as bottle washing machines and can
cleaning machines, shall be cleaned and maintained periodically.
8.4.9 Aseptic filling systems shall be sterilized before use. All pipelines shall be
cleaned and disinfected by means of cleaning in place (CIP) after construction
and disassembled for cleanliness inspection periodically.
8.4.10 After cleaning and sterilization, movable equipment and utensils shall be
stored in appropriate places that can prevent the food contact surface from
contamination and ensure they are ready for use.
8.4.11 The water used to clean the equipment and tools in direct contact with food
shall meet potable water quality standards.
8.4.12 Equipment or facilities used in food manufacturing shall not be used for other
TQF-PCS-016
TQF Management Technical Specifications—Certification Regulation Ver. 2.0
42 / 66 ©Taiwan Quality Food Association
[Canned Food]
non-food production purposes.
8.5 Personnel hygiene management
8.5.1 Workers having direct contacts with foods shall keep their hands clean at all
times to prevent contamination. Such workers shall not have long fingernails,
polished fingernails, or wear ornaments. Workers shall also wash and/or
sanitize their hands thoroughly with appropriate equipment before work
(including leaving work and return to their post afterwards) or on any
occasions that may contaminate their hands.
8.5.2 New employees shall have a health examination in a health or medical
institution prior to employment. During the course of their employment,
employer shall take the initiative to establish routine health examinations
which shall include relevant examinations in compliance with the Good
Hygiene Practice (GHP) provision.
8.5.3 Employees infected with hepatitis A, hand skin diseases, rash,
abscess, wound, tuberculosis, typhoid or other infectious diseases
even in its incubation period, that may contaminate food shall not be
working in direct contact with food.
8.5.4 Workers in the operation zone shall keep their hands clean or wear clean and
sanitized waterproof gloves.
8.5.5 Operators must wear a clean work clothes and hair nets to prevent hair,
dandruff and foreign materials from falling into and contaminating the food,
food contact surface or inner packaging material. Shall wear mask when
necessary.
8.5.6 No smoking, chewing gum or betel nut, eating, drinking and other behavior
that may cause food contamination is allowed in the production area. It is
necessary to take precautions to protect against contamination of food, food-
contact surfaces, or food-packaging materials with microorganisms or foreign
substances, including but not limited to sweat, saliva, cosmetics, and
medicines applied topically.
8.5.7 Hand washing or (and) disinfection shall be properly done according to the
hand washing procedures and instructions.
8.5.8 Personal clothing should be stored in the change room and should not brought
into food handling area or equipment, appliances and utensils cleaning areas.
8.5.9 Before entering food factory (including work shift), or after using the toilet
(the sign indicating washing hands after use should be posted in the toilet), or
because of spitting, nose blowing lead to possible contamination of the hands,
TQF-PCS-016
TQF Management Technical Specifications—Certification Regulation Ver. 2.0
43 / 66 ©Taiwan Quality Food Association
[Canned Food]
hands shall be washed properly and even disinfect when necessary.
8.5.10 The access of visitors or off-site staffs shall be properly controlled. Hygienic
requirements for them should comply with those for on-site operation
personnel.
8.6 Management of chemicals and supplies such as detergents and disinfectant
8.6.1 Detergents and sanitation agents should have been proven that it is safe and
applicable for the purpose being used.
8.6.2 Inside the food operation area, with the exception of those agents necessary for
environmental protection and sanitation purposes, other agents are not allowed
in the food operation area.
8.6.3 Sanitizing agents, sanitizers, and dangerous reagents shall comply with
relevant specifications, and shall be clearly identified and labeled with
indication of its toxicity, instruction of how to use, and emergency handling
and stored and kept locked in a specific designated location to avoid food from
being contaminated. A specialist in charge should be assigned of their storage
and record the amount of usage.
8.6.4 Strict preventive measures and limitations shall be taken regarding the use of
pesticides and sanitizing agents, to protect against contamination of food,
food-contact surfaces, or food-packaging materials. They shall be used by or
under the supervision of a sanitation personnel who understands their potential
harm to the human body (including in the event of food contamination).
8.7 Waste material
8.7.1 Handling of waste material shall comply with waste material cleaning law and
related regulations of the provisions of removing and handling, and shall be
collected, classified and properly disposed according to their characteristics.
Perishable waste shall be removed at least once a day, the container shall be
cleaned and disinfected after emptied.
8.7.2 Waste disposal areas shall not present bad odors or harmful (toxics) gases. It is
necessary to prevent the harboring of pests and the food, food contact surface,
water source and ground from being polluted.
8.7.3 Waste material and receptacles shall not be allowed to accumulate inside the
food operation area or outside the building to prevent the breeding of pests and
vectors.
8.7.4 Raw materials handling, processing, packaging, storage and other areas, shall
have waste receptacles that are easy to clean and disinfect (with exception of
the ones that are discarded after usage), can be closed (or sealed), and
TQF-PCS-016
TQF Management Technical Specifications—Certification Regulation Ver. 2.0
44 / 66 ©Taiwan Quality Food Association
[Canned Food]
regularly (at least once a day) removed from the plant. Reusable containers
should be cleaned and disinfected immediately after discarding the content. If
a large number of waste is generated, it shall be transported outside the
facility, as soon as possible, and also away from the plant, in order to prevent
pests breeding, and the contamination of water sources, ground, ground water
etc.. The machines and equipment used for waste handling shall be cleaned
and disinfected immediately upon finishing operation.
8.7.5 When there is waste exposure that may put human health and food safety in
direct danger such as chemicals, radioactive materials, pathogenic
microorganisms and food spoilage, etc. special storage facilities shall be set
up.
8.7.6 Harmful (toxic) gases, waste water, litter, noise pollution, etc. shall be avoided
or handled in accordance with relevant laws and regulations in order to prevent
environmental pollutions.
9 Food Production Management
9.1 Establishment and implementation of the "Standard Operation Procedure for Food
Manufacturing".
9.1.1 The Production Department is responsible for the establishment and revision
of the "Standard Operation Procedure for Food Manufacturing", and approved
by the quality assurance and related departments.
9.1.2 The "Standard Operation Procedure for Food Manufacturing" shall specify the
recipe, standard operation procedure, process control standard (including at
least the manufacturing process, control object, control item, control standard
value and precautions, etc.) and machinery and equipment operation and
maintenance standards.
9.1.3 The employees shall be educated and trained to carry out their work in
accordance with the "Standard Operation Procedure for Food Manufacturing"
so as to be in compliance with the production, sanitation, hygiene and quality
control requirements.
9.2 Raw material handling
9.2.1 The food factory shall establish raw material inspection standard procedure for
its reception, and shall not use primary or secondary raw materials from which
microorganisms and toxic substances (e.g., cyanide in the cassava) cannot be
removed or reduced to an acceptable level during normal processing. Semi-
TQF-PCS-016
TQF Management Technical Specifications—Certification Regulation Ver. 2.0
45 / 66 ©Taiwan Quality Food Association
[Canned Food]
finished products or finished products the raw materials, manufacturing
environment, manufacturing process and quality control shall meet the hygiene
requirements of the Good Manufacturing Practices of food factories. The same
requirements will stand for semi-finished or finished products, which are used
as raw materials, and are produced by their own factory or outsourced.
9.2.2 Raw materials shall go through sensorial inspection before use, and if
necessary, go through selection and removal of foreign matters or
substandard specification materials.
9.2.3 A procurement plan shall be established and implemented for purchasing
perishable fresh ingredient agricultural products, such as fruits and vegetables.
They shall be shipped to the factory from the production site or supplier as
quickly as possible and processed as soon as possible. Unprocessed ingredients
shall be refrigerated or stored in the ingredient zone or storage zone for proper
management to prevent contamination and quality deterioration.
9.2.4 Fresh raw materials, should be cleaned when necessary, and the water should
meet potable water quality standards. If water is recycled, it shall be properly
disinfected, and filtered, when necessary, so as to avoid raw materials from
secondary contamination.
9.2.5 Approved raw materials and substandard raw materials shall be stored
separately, and clearly identified.
9.2.6 Food additives used in processing shall be qualified and registered by the
Ministry of Health and Welfare (MOHW) and with complete product labeling.
9.2.7 Ingredients and food additives shall be separately stored in appropriate
conditions with good ventilation, appropriate temperature, and appropriate
humidity by variety and by lot number. Records of temperature and humidity
of the warehouse shall be maintained.
9.2.8 Ingredients shall be used based on the first in and first out (FIFO) principle
and be used within expiry date. Frozen ingredients shall be thawed in
conditions that can prevent them from quality deterioration.
9.2.9 Raw materials shall be stored in such a way that they can be protected
from contamination and damages, and minimize quality deterioration.
When temperature and humidity control are needed, control limits shall be established. Frozen raw materials should be kept below -18℃, and
refrigerated raw materials below 7℃ and above the freezing point of
water.
9.2.10 Effective vector prevention measures, as well was measures to prevent damage
TQF-PCS-016
TQF Management Technical Specifications—Certification Regulation Ver. 2.0
46 / 66 ©Taiwan Quality Food Association
[Canned Food]
on the external package from contaminating ingredients and food additives,
shall be implemented in the ingredient storage zone.
9.2.11 Unused ingredients and food additives after production shall be sealed and
packaged properly according to storage needs before storing in appropriate
locations to prevent contamination. The use of such ingredients and food
additives shall be prioritized during the period when their quality remains
qualified.
9.3 Canned food container handling
9.3.1 When receiving containers, suppliers shall provide a proof of quality or
sampled for testing its quality and hygiene.
9.3.2 The storage shall be prevented from contamination, when the temperature and
humility are required to be controlled during the storage shall established
managing methods and standards, and recorded.
9.3.3 Shall adopt an appropriate mothed to keep container clean before use.
9.3.4 During delivering, moving, canning, etc., bruising should be avoided and
intrusion of debris should be prevented.
9.4 Manufacturing operation
9.4.1 All food manufacturing operation procedures, including packaging and
storage, shall be in accordance with the principles of food safety and
sanitation. Food shall be quickly processed under controlled condition to
minimize microbial growth and food contamination as possible.
9.4.2 When the control of temperature, humidity, pH value, water activity,
pressure, flow rate and time are needed during operation procedures, a
related control methods and control limits shall be established and
recorded, to ensure that food is not spoiled or being contaminated by
mechanical failure, time delays, temperature changes and other
factors.
9.4.3 Ingredients shall be processed as quickly as possible. Where production is
lagged by mechanical failures, timely and effective responsive actions shall be
taken on formulated or mixed semi-finished products to prevent deterioration,
quality change, or contamination. When production resumes, such semi-
finished products or finished products that have been lagged behind shall be
examined and assessed. Seriously deteriorated semi-finished products or
finished products shall be discarded immediately and eliminated from
processing.
9.4.4 A double check system shall be established and exactly implemented for the
TQF-PCS-016
TQF Management Technical Specifications—Certification Regulation Ver. 2.0
47 / 66 ©Taiwan Quality Food Association
[Canned Food]
weighing and use of food additives, and records shall be maintained.
9.4.5 When storing formulated semi-products in storage barrels, workers shall pay
attention to contamination by foreign matter and avoid long-term storage.
Where refrigeration is required, the refrigeration temperature shall be between
freezing point and 7°C.
9.4.6 In the course of operation, appropriate methods shall be used to
prevent pathogenic microorganism growth, and to prevent food
degradation during manufacturing, storage and transportation, such as
sterilization, irradiation, pasteurization, freezing, refrigeration, and pH or
water activity control.
9.4.7 The path for transporting semi- finished products and finished products via
pipes shall be strictly controlled to prevent mixing with other products or
foreign matter, such as acid solutions, alkaline solutions, syrups, or cleaning
water, to affect quality.
9.4.8 Filters, metal detectors, and other effective measures shall be equipped in
appropriate locations of formulating barrels, storage barrels, and other
pipelines to prevent foreign matter from mixing with semi- finished products
and finished products.
9.4.9 The operation, utilization and maintenance of equipment, containers and
utensils which are in contact with the raw materials, semi-finished and finished
products shall not contaminate food during processing and storage. Equipment,
containers and utensils in contact with raw materials or contaminants shall not
be used for handling finished food products unless thoroughly cleaned and
disinfected. Food containers that contain semi-finished food shall not be
directly put on the ground to avoid splashing water contamination or cross-
contamination from the bottom of the container. When entering from the
general operation area into the controlled operation area, appropriate cleaning
and disinfection measures shall be established to prevent food contamination.
9.4.10 Sterilized can after cooling down, using conveyor belt for conveying shall
avoid the contact between conveyor belt and roll seal (seal); damaged
conveyor belt and caning buffering device shall be replaced, the conveyor belt
and track which is contact with seal shall be kept clean.
9.4.11 Water for making ice cubes which directly come into contact with food
during processing shall meet the standard of potable water, and the ice
cubes shall be made under sanitary conditions.
9.4.12 An aseptic filling zone shall be appropriately segregated, and operation shall
TQF-PCS-016
TQF Management Technical Specifications—Certification Regulation Ver. 2.0
48 / 66 ©Taiwan Quality Food Association
[Canned Food]
be implemented in accordance with the environmental sanitation management
standards for clean zones. Sanitation and filling conditions shall comply with
the operating specifications to prevent re-contamination.
9.4.13 Containers, such as empty cans, empty bottles, or empty boxes, for filling shall
be washed, and re-sterilized as necessary, before use.
9.4.14 The filling of products shall be managed, to ensure compliance with the
volume of sterilization condition presented in clause 6.6, this specific
provision.
9.4.15 When heating for re-sterilization after filling and sealing, products shall not be
retained for a long period of time to prevent temperatures from falling below
the initial sterilization temperature and thereby affecting sterilization safety.
9.4.16 Degassing after filled shall be managed and to ensure compliance with the
volume of sterilization condition presented in clause 6.6, this specific
provision. When using degassing device, it shall be cleaned and maintained.
9.4.17 Ultra-high temperature (UHT) short-time sterilizers shall be disassembled and
checked for leakage periodically.
9.4.18 Appropriate corrective actions shall be taken for anomalies in the
manufacturing process; anomalies shall be reviewed to prevent recurrence; and
records shall be maintained.
9.4.19 Effective methods shall be used to prevent products under processing or in
storage from contamination by ingredients or scraps.
9.4.20 Handling raw material blanching
9.4.20.1 During blanching, temperature (especially temperature of the inlet and
outlet) and time shall be strictly controlled, quickly cool down and moved
to the next operation procedure. Equipment shall be routinely cleaned to
prevent thermo-resistant bacteria growth and contamination, and to
minimize its contamination. If the blanched food is cooled before filling,
the cooling medium should conform to the principle of safety, hygiene and
sanitation.
9.4.20.2 Blanching devices shall be cleaned thoroughly. Those who adopts hot
water blanching shall drain and refill hot water frequently, and preventing
blanched water from contamination.
9.4.20.3 The water for washing raw material and cooling shall comply with
“Potable water quality standard”.
9.4.21 Foods that rely on pH control to prevent pathogenic micro-organism growth,
such as acidic or acidified foods, shall be regulated and keep the pH below 4.6.
TQF-PCS-016
TQF Management Technical Specifications—Certification Regulation Ver. 2.0
49 / 66 ©Taiwan Quality Food Association
[Canned Food]
This requirement should be achieved by one or more of the following effective
methods:
9.4.21.1 Adjustment of pH values of raw material, semi-finished product and
finished product.
9.4.21.2 Controlling the amount of acidic or acidified food added to the low acid
food.
9.4.22 When selecting inner packaging materials, it must protect food during
normal storage and distribution, and to avoid migration of harmful
substances into food and meet sanitation and hygiene standard. Inner
packaging materials shall not be reused with the exception of glass
bottles, stainless steel containers and barrels (e.g. used as water or
invert syrup container), but they shall be properly cleaned. If necessary,
they shall be effectively sterilized.
9.4.23 An effective system, such as labeling with thermochromic inks or
thermochromic papers, shall be established to control the need for sterilization
to prevent sterilized and unsterilized cans from mixing.
9.4.24 The initial temperature of the contents in a container during each time of
sterilization shall be tested and recorded before sterilization to ensure the
initial temperature of sterilization is not below the minimum initial
temperature specified by the sterilization requirements.
9.4.25 Pre-sterilization operation: before sterilization operation, all the contact
surfaces of sterilizer and afterword equipment shall reach the requirement of
commercial sterilization, and shall have appropriate device to present its
effective.
9.4.26 An accurate wall mount clock shall be used for counting sterilization time.
Wristwatches or pocket watches shall not be used.
9.4.27 A sterilization work report shall not be completed in advance or supplemented
afterwards. Records shall be faithfully maintained.
9.4.28 Sterilization operation reports and automatic temperature recording document
shall be checked and signed by sterilization manager within a week after the
operation.
9.4.29 The document of sterilization and sealing shall be kept at least for 5 years.
9.4.30 In the air release and sterilization processes, LACF factories shall maintain the
steam pressure of the main steam pipes at 6kg/cm2 or higher.
9.4.31 During the sterilization process, the temperature read from the mercury-in-
glass thermometer shall be the sterilization temperature that shall not be
TQF-PCS-016
TQF Management Technical Specifications—Certification Regulation Ver. 2.0
50 / 66 ©Taiwan Quality Food Association
[Canned Food]
substituted by the temperature on the temperature recorder.
9.4.32 Cold chlorinated water shall be added to cooling water from sterilization
(except for retort pouches). The minimum volume of ionized residual chlorine
at the outlet shall be 0.2ppm.
9.4.33 The product temperature of cooled cans shall be lukewarm and not higher than
40℃.
9.4.34 Handling sterilization anomalies
9.4.34.1 Where controls relating to commercial sterilization safety, such as air
release, sterilization, critical factors, seaming completeness, and
acidification controls, are found to have deviated from the sterilization
conditions (requirements), all affected products shall be re-processed and
re-sterilized or retained for evaluation. Where deviation is found during the
process, corrective actions recommended by the organization(s)
establishing the sterilization conditions shall be implemented.
9.4.34.2 Retained products shall be evaluated by a government accredited
organization. Products with threats to public health safety shall be re-
processed/re-sterilized or destroyed.
9.4.34.3 Records shall be exactly maintained for the status, cause(s), handling
method(s), correction procedures, and correction outcomes of a
sterilization anomaly and archived individually.
9.5 Control of critical factors
9.5.1 The internal time for monitoring and recording the time, temperature, and
critical factors of sterilization shall be 15 minutes in principle, with a
maximum of not more than 60 minutes.
9.5.2 All control points of the aseptic processing and packaging system, such as the
flow speed, temperature, and concentration of the sterilization medium; and
the speed of containers passing through the sterilization system and seaming
shall be checked and recorded at appropriate times (at least once an hour).
10 Quality Control
10.1 Establishment and implementation of the "Standard Operation Procedure for
Quality Control"
10.1.1 The Quality Assurance Department is responsible for the establishment of the
“Standard Operation Procedure for Quality Control", and it shall be approved
by the Production Department and effectively implemented to ensure that food
TQF-PCS-016
TQF Management Technical Specifications—Certification Regulation Ver. 2.0
51 / 66 ©Taiwan Quality Food Association
[Canned Food]
produced are suitable for human consumption. The content of the manual shall
include the provisions from section 10.2 to 10.6, as a basis for quality control
ensuring product quality. It is also applicable when amended.
10.1.2 “Process and Quality Control Engineering Flow Chart” that are based
on critical control factors shall be established for every product. Its
contents shall include the scope, control points, control limits, sampling
frequency and testing methods etc., and shall be implemented and
recorded.
10.1.3 A quality control standard shall include the following items:
10.1.3.1 Ingredient specifications and quality acceptance criteria.
10.1.3.2 Process quality control standards and methods.
10.1.3.3 Finished product specifications and OQC sampling inspection criteria.
10.1.3.4 Methods of tests and analyses.
10.1.4 Records of quality inspections shall be maintained. A quality record shall
include the following items:
10.1.4.1 The name of the sample, sampling location, sampling size, lot number and
other explicit codes, sampling date, and inspection date.
10.1.4.2 The references of special inspection methods, where necessary.
10.1.4.3 Records of inspection results to be compared with the established
specifications.
10.1.4.4 The name of test operators and date of tests.
10.1.5 Testing methods shall be based on promulgated normative. When a modified
testing method is adopted, it shall be checked regularly against the
promulgated normative and recorded. When there is no national normative or
regulation, the supplier shall provide clear product specification, testing items
and internationally recognized testing methods as supporting documents.
10.1.6 A control system shall be established to avoid possible biological and chemical
contamination during testing, and effectively implemented.
10.1.7 Drugs or chemicals used in quality control tests shall be used under effective
conditions and controlled.
10.1.8 An annual calibration program for measuring instruments (e.g., thermometers,
pressure gauges, weighing scale, etc.) that are important to the manufacturing
process shall be established and recorded. Meters or thermometers and
pressure gauges mounted on heat sterilization equipment that are closely
related to food safety and hygiene shall be calibrated by an authorized entity at
TQF-PCS-016
TQF Management Technical Specifications—Certification Regulation Ver. 2.0
52 / 66 ©Taiwan Quality Food Association
[Canned Food]
least once a year, and effectively implemented and recorded.
10.1.9 Appropriate statistical methods shall be used to analyze the quality control
data recorded.
10.1.10 All food factories shall be up-to-date with all current relevant regulations or
normative information.
10.2 Contract management The food factory shall establish and maintain written procedures for contract review and for its operational coordination.
10.2.1 Contract review
Upon acceptance of each order placed by customers, it is necessary to review
that the requirements have been clearly written and ensure that the customer
requests and requirements can be properly met.
10.2.2 Contract amendment
Amendment of contract or purchase order shall be documented and
communicated accurately to relevant departments and executed in accordance
with the revised content.
10.3 Quality control of raw materials
10.3.1 For the quality control of raw materials it is necessary to specify the quality
specifications of raw materials and packaging materials (including source
information and control points for risk and hazard), testing items, inspection
criteria, sampling plan (sample containers should be properly identified) and
testing methods, and effectively implemented.
10.3.2 Suppliers evaluation procedure shall be established, which shall include the
method applied and frequency, be effectively implemented and recorded.
When possible, on-site assessment of suppliers shall be conducted.
10.3.3 Each batch of raw materials (additives) shall be inspected and approved by
quality assurance personnel before released for use. Traceability and source
control measures of raw material shall be established (including supplier's raw
material quality certificate and certificate of origin, raw material provenience
details and testing reports). Establishment of a TQF certificated products
quality history or curriculum (including product name, lot number,
manufacturing plant, expiration date, ingredients of raw material and its origin,
raw materials testing report, finished product testing report information). Raw
materials that were not approved during inspection shall be clearly identified,
and appropriately managed.
10.3.4 Prior to release for use, it is necessary to verify that those raw materials with
TQF-PCS-016
TQF Management Technical Specifications—Certification Regulation Ver. 2.0
53 / 66 ©Taiwan Quality Food Association
[Canned Food]
potential contamination of pesticides, heavy metal or toxins are safe and the
amount of residues permitted are in compliance with regulatory requirements.
10.3.5 The acceptance of packaging materials should include the source, the
application of materials and their use and storage, etc., in order to avoid
contamination of the product. Inner packaging materials shall meet hygienic
and sanitation normative standards, and suppliers of those packaging materials
should provide periodic test reports to verify the compliance with food safety,
sanitation and hygiene requirements. The testing reports shall be provided
again by the supplier upon changing suppliers or specification.
10.3.6 Special designated storage for food additives shall be set up and be managed
and controlled by authorized personnel who is responsible for issuing the
materials and controlling the expiration date. Log sheets with list of food
additives type, registration number under the health authority, material check-
in and check-out etc. shall be documented.
10.3.7 Raw materials which are provided by the consignor for contract manufacturing
shall be properly stored and controlled, and any missing, damaged, or out of
specs materials shall be recorded and reported to the contract supplier. When
contract manufacturing products apply for certification, the food factory shall
be able to trace back the source of the raw materials and confirm the
composition, purity, etc. of the product, providing supporting documents to
ensure the quality of the products. Qualification for the TQF product
certification will be withdrawn from the supplier for providing false
information.
10.4 Quality control during processing
10.4.1 Hazard Analysis and Critical Control Points shall be performed, and testing
items, criteria and methods for sampling and testing shall be established,
effectively implemented and documented.
10.4.2 Corrective actions and preventive measures shall be established when
deviation from control limits occur during processing, and immediate
investigation and corrective action shall be taken and documented.
10.4.3 The sufficiency of ionized residual chlorine in water for washing ingredients
shall be analyzed periodically, and records shall be maintained.
10.4.4 The temperature and time of blanching or steaming/cooking shall be checked
periodically and records shall be maintained.
10.4.5 The cleanliness and suitability for use of utensils and equipment for
TQF-PCS-016
TQF Management Technical Specifications—Certification Regulation Ver. 2.0
54 / 66 ©Taiwan Quality Food Association
[Canned Food]
formulation and mixing shall be checked before use.
10.4.6 Measuring devices, such as the Brix hydrometer, hydrometer, and scale, shall
be calibrated periodically.
10.4.7 The appearance and characteristics, normal taste, and purity of juice, syrup,
water quality and other secondary ingredients, and food additives shall be
confirmed before use. The dose shall be correct as formulated. Records shall
be maintained.
10.4.8 The appearance, taste, degree Brix, acidity, and foreign matter on
semi-finished products shall be examined after formulation to ensure
there are no anomalies.
10.4.9 The water for making ice that has direct contact with foods during processing
shall comply with the drinking water standard. Such ice shall be made in a
sanitary environment.
10.4.10 Where dichlorination of water for processing is required before formulation,
residual chlorine shall be analyzed immediately afterwards to ensure there is
no residual chlorine contained in the water.
10.4.11 When hot filling is required, the filling temperature shall be checked to ensure
compliance with the control conditions.
10.4.12 During the seaming process, the products seamed first shall be examined for
sealing or seaming integrity. Seaming shall be adjusted where necessary.
Seaming integrity shall be implemented periodically throughout the production
process to ensure seaming integrity and safety. Records shall be maintained.
10.4.12.1 Double seaming of metal containers
10.4.12.1.1 Appearance inspection: Implemented every 30 minutes after
operation begins. Inspection items include appearance defects, seam
thickness (T), seam width (W), countersink (C), and body height. An
M-V control chart shall be produced for the reference of capping. A
can shall be opened for inspection when appearance anomalies are
detected.
10.4.12.1.2 Can opening inspection: To be implemented before and after
operation. Operation shall begin only after the requirements are met.
After operation begins, a can opening inspection shall be
implemented every four hours. Inspection and recording items shall
include appearance and interior detects, seam thickness (T), seam
width (W), the length of the cover hook (CH) and body hook (BH),
overlap (OL) and percentage of overlap (OL%), countersink (C),
TQF-PCS-016
TQF Management Technical Specifications—Certification Regulation Ver. 2.0
55 / 66 ©Taiwan Quality Food Association
[Canned Food]
internal droop (ID), wrinkling (WR), and pressure ridge (PR). When
serious defects are found in the can opening inspection, the seamer
shall be shut down for mechanical re-adjustments before re-running
the can opening inspection.
10.4.12.1.3 When turning on a seamer after trouble shooting or mechanical
adjustment, the appearance inspection and can opening inspection
shall be implemented, and seam thickness (T) and countersink (C)
shall also be checked. Detailed records of adjustments and inspection
results shall be maintained.
10.4.12.1.4 Cold water shall be filled in cans to test the degree of vacuum of
vacuum capping machines.
10.4.12.2 Capping of glass containers
10.4.12.2.1 The sealing efficiency of capping machines shall be inspected every
day before operation or restarting machines after suspension.
Operation shall begin only after the requirements are met. Records
shall be maintained.
10.4.12.2.2 The interval of appearance inspection and recording shall not exceed
30 minutes. The interval of can opening inspection and recording
shall not exceed four hours. The appearance and can opening
inspections after sterilization and cooling may be combined with the
can opening inspection of finished products.
10.4.12.2.3 Cold water shall be filled into cans to test the degree of vacuum of
vacuum capping machines.
10.4.12.3 Heat sealing of retort pouches
10.4.12.3.1 The sealing efficiency of sealers shall be inspected every day before
operation or restarting machines after suspension. Operation shall
begin only after the requirements are met. Records shall be
maintained.
10.4.12.3.2 The interval of appearance inspection and recording shall not exceed
30 minutes. The interval of the compressive strength test and interior
residual air test and recording shall not exceed four hours.
Appearance and can opening inspections shall be conducted after
sterilization and cooling and may be combined with the can opening
inspection of finished products.
10.4.12.3.3 Appearance inspection of retort pouches’ sealing, shall be free from
defects such as pin holes, uneven seals, residual inclusions at seals, or
TQF-PCS-016
TQF Management Technical Specifications—Certification Regulation Ver. 2.0
56 / 66 ©Taiwan Quality Food Association
[Canned Food]
incomplete seals; the quality and inspection methods shall comply
with related requirement of inspection of sterilization-bag-packaged
food and packaged food of republic of china standard.
10.4.12.4 Other sealing systems
10.4.12.4.1 To be inspected every day before operation or restarting machines
after suspension of use. Operations shall begin only after the
requirements are met. Records shall be maintained.
10.4.12.4.2 The interval of appearance inspection and recording shall not exceed
30 minutes. The interval of the compressive strength test and interior
residual air test and recording shall not exceed four hours.
Appearance and can opening inspections shall be conducted after
sterilization and cooling and may be combined with the can opening
inspection of finished products.
10.4.13 The inspection frequency and the control boundary of control items shall be
established according to the item characteristics. A quality control chart shall
be established to ensure the stability of quality, sanitation, and safety.
10.4.13.1 Blanching temperature should be checked every 30 minutes (a -Rm
control chart is recommended).
10.4.13.2 Filling quality or quantization shall be checked every hour (a -R control
chart is recommended).
10.4.13.3 The degree of vacuum of vacuum capping machines or the center
temperature of degassed cans shall be checked every hour (a -R control
chart is recommended).
10.4.13.4 Contents shall be checked every hour (a -R control chart is
recommended).
10.4.13.5 Seam appearance (W, T, C, H) shall be checked every 30 minutes (an M-
V control chart is recommended).
10.4.14 When anomalies are found within the process inspection results, abnormal
semi-finished products and finished products shall be effectively segregated,
cause(s) shall be traced, and corrective actions taken as quickly as possible.
10.4.15 The sterilization work report of an LACF factory shall include: product name;
lot number (or symbol); date; can type; sterilizer (machine) number; rough
number of cans; pressure, initial temperature, air release time (start and finish
times) of the main steam pipes; sterilization time (start and finish times);
sterilization temperature indicated on the mercury-in-glass thermometer and
temperature recorder; product temperature after cooling; ionized residual
x
x
x
x
TQF-PCS-016
TQF Management Technical Specifications—Certification Regulation Ver. 2.0
57 / 66 ©Taiwan Quality Food Association
[Canned Food]
chlorine in cooling water; and other required items.
10.4.16 Items required for records of various sterilization methods:
10.4.16.1 Static sterilizers: air release start and finish times; air release time;
temperature at the end of air release; time and temperature at the
beginning, in the middle, and at the end of sterilization (time and
temperature in the middle of sterilization can be omitted when an
automatic controller is equipped).
10.4.16.2 Rotary sterilizers: Status of the condensate check valve, rpm, and
designated sterilization conditions, such as top open space, viscosity, solid
upper limit, content lower limit, and solid percentage.
10.4.16.3 Retort pouch processing and packaging:
10.4.16.3.1 Temperature at the inlet and outlet of the constant temperature
insulation pipe, thermometer, and temperature recorder.
10.4.16.3.2 Temperature at the final outlet of the heater, thermometer, and
temperature recorder.
10.4.16.3.3 The pressure recorded in the differential pressure controller when
product heat exchange is used.
10.4.16.3.4 Product flow speed: Flow speed can be detected from the speed of the
quantitative pump or filling and sealing speed.
10.4.16.3.5 The flow speed and temperature of the sterilization medium.
10.4.16.3.6 Container retention time in the sterilization medium, and temperature-
related data shall be recorded. The lot number for identifying
containers shall also be recorded.
10.4.16.4 Acidified canned foods: Process pH control points, sterilization critical
factors, and sterilization time and temperature.
10.4.16.5 When controlling critical factors (e.g. water activity) with heat treatment is
used in sterilization, the product formula, heat treatment conditions, water
activity, and other critical factors shall be recorded.
10.5 Quality control of finished products
10.5.1 Quality specifications, testing items, testing standards, sampling and testing
methods shall be established.
10.5.2 Finished product inspection: Representative samples shall be taken from each
lot of finished products in accordance with the finished product specifications
and OQC sampling criteria established by a factory for the finished product
TQF-PCS-016
TQF Management Technical Specifications—Certification Regulation Ver. 2.0
58 / 66 ©Taiwan Quality Food Association
[Canned Food]
inspection. The inspection items of finished canned products shall include:
10.5.2.1 Contents (e.g. degree Brix).
10.5.2.2 Solid quantity or content quantity.
10.5.2.3 pH value.
10.5.2.4 Degree of vacuum.
10.5.2.5 Taste.
10.5.2.6 Foreign matter.
10.5.3 Every lot of finished products shall be subject to quality testing. Non-
conforming products shall be appropriately managed.
10.5.4 A sample retention plan shall be established to retain samples from each lot of
finished products. A food storability test shall be conducted on finished
products, as necessary, to test food preservation capacity.
10.5.5 Every lot of product shall be sampled and inspected for its can-opening quality
within a working-day, and recorded the results.
10.5.6 The can opening inspection shall be conducted on each lot of finished products
within one workday, and records shall be maintained.
10.5.7 A 10-day incubation test at 37°C for shall be conducted on samples taken from
each lot after sterilization. After the test is completed, the can opening
inspection shall be conducted in accordance with 10.5.2, and records shall be
maintained.
10.6 Testing condition Raw materials, semi-finished products, final semi-finished products and finished products shall be properly identified, handled and controlled. When the regulation of "Food Businesses Shall Enact Food Safety Monitoring Plan and Mandatorily Conduct Tests and Meet the Minimum Testing Cycle and Other Relevant Matters" enacted by the Ministry of Health and Welfare is applicable to the raw material, semi-finished product or finished product being produced, it shall comply with the requirements of that regulation.
10.7 Non-conforming product handling
10.7.1 The factory shall establish a non-conforming product control plan, effectively
implemented and recorded.
10.7.2 Non-conforming products shall be effectively separated and make sure that
they are not placed on the market; those introduced into the market shall be
recalled and appropriately managed. The quality control of the third-party: food manufactories shall establish and maintain the documented procedure of any service that is related to food safety matters (such as equipment maintenance, instrument calibration, disinfection, and vector control, logistics, etc.). Each document shall be stored properly, easy to access when necessary and reviewing periodically.
TQF-PCS-016
TQF Management Technical Specifications—Certification Regulation Ver. 2.0
59 / 66 ©Taiwan Quality Food Association
[Canned Food]
11 Warehousing and transportation management
11.1 Warehousing and sanitation management
11.1.1 A storage and transport control procedure shall be established, it shall include
storage area separation, storage conditions, inventory control, storage
management, etc.., and be effectively implemented and recorded.
11.1.2 Storage and transport method and its surroundings shall avoid direct exposure
of sunlight, rain, wide fluctuation of temperature or humidity and any direct
impact or collisions and water accumulation to prevent the food ingredients,
composition, quality and concentration from being affected by undesirable
external factors, and maintaining food degradation at a minimum level.
11.1.3 Storage shall be always keep clean and organized, swept and cleaned, and
storage items shall not be placed directly on the ground. Cold chain storage
and transportation equipment shall be available when necessary, to ensure
products are maintained in insulated (temperature control) condition.
11.1.4 Temperature (and humidity, if necessary) in the storage shall be recorded, and
the storage items shall be regularly checked, when abnormalities are detected,
corrective action shall be immediately performed. When possible risk of
quality deterioration are presented due to damaged packaging or prolonged
storage, food products shall be re-inspected to ensure that they have not been
contaminated and the deterioration of quality is still acceptable.
11.1.5 When temperature and humidity control are necessary, control methods and
parameters limit shall be established, documented and recorded.
11.1.6 Food items rotation shall be based on the “first in first out” principle; products
shall be stable and ventilated when stacked.
11.1.7 There shall be measures to prevent cross-contamination of any item that may
contaminate raw materials, semi-finished products or finished products; those
that cannot effectively prevent cross-contamination shall be prohibited from
being stored or transported together with raw materials, semi-finished products
or finished products.
11.1.8 Containers and vehicles for transportation shall be checked to prevent
contamination of ingredients or the factory area. Containers and vehicles for
shipping shall be checked before loading to ensure product cleanliness and
sanitation. When temperature control is required during transportation,
vehicles with effective temperature control shall be used, and records shall be
TQF-PCS-016
TQF Management Technical Specifications—Certification Regulation Ver. 2.0
60 / 66 ©Taiwan Quality Food Association
[Canned Food]
maintained.
11.1.9 Transportation methods to protect finished products from the influence of
unfavorable environmental factors on quality shall be specified.
11.1.9.1 When transporting finished products in a truck without a cover, canvas,
plastic, and other protection against sunshine and rain shall be used.
11.1.9.2 Appropriate protection shall be provided for finished products packed in
easy-to-break bottles, carbon boxes, or aluminum packs to prevent impact
and/or squeezing from affecting product quality and safety during
transportation.
11.1.9.3 Items with potential threats of contamination shall not be transported with
finished products.
11.1.10 Incoming delivery containers and vehicles transporting purchased goods into
the plant shall be inspected, so as not to cause raw materials or plant site
environmental contamination. Outgoing delivery containers and vehicles used
for food product shipping or dispatch shall be also inspected before loading to
assure food safety, sanitation and hygiene conditions. Good transportation
requiring temperature control shall have an effective temperature control
system, and be documented and recorded. The food factory shall require
logistic operations to be in accordance with the temperature conditions of the
products. Low temperature foods shall be promptly loaded and unloaded at a
temperature of 15 degrees Celsius and product temperature shall be detected
and recorded.
11.2 Storage and transport records Inventory and shipping records shall be established, including lot number, time, location, destination, quantity etc., in order to be recalled quickly when any problem comes up.
12 Labeling
12.1 Product labeling shall be in compliance with the Act Governing Food Safety and
Sanitation. When that regulation is not applicable, other relevant laws and
regulations of central competent authorities shall be applied. The label of products
for export shall comply with the requirements of laws and regulations of the
intended country.
12.2 Retail products label shall be presented in Chinese and generic symbols with the
TQF-PCS-016
TQF Management Technical Specifications—Certification Regulation Ver. 2.0
61 / 66 ©Taiwan Quality Food Association
[Canned Food]
following information and must be set off in a frame text box (in the below order):
12.2.1 Product name.
12.2.2 List of ingredients. When it is a mixed ingredient, each component shall
be also listed.
12.2.3 Weight, volume or quantity.
12.2.4 List of food additives.
12.2.5 Name, address, customer service line or phone number of the
manufacturer or company in charge. When only the name of the
company in charge is indicated, the use of the TQF product certification
mark is not permitted.
12.2.6 Country of origin.
12.2.7 Nutrition label.
12.2.8 Genetically modified food ingredients.
12.2.9 Expiration date. When required by the central competent authority, date
of manufacture, shelf life or preservation conditions shall be also
indicated. This information shall be printed on the packaging rather than
tagged.
12.2.10 Lot number: Product lot shall be indicated by explicit or implicit code,
which enables tracing back the raw materials and ingredients records
involved in the manufacturing of a product.
12.2.11 Instructions for consumption or cooking and any special storage
conditions, if necessary.
12.2.12 Other information required as indicated by the central competent
authority.
12.3 It is recommended that finished products be labeled with bar code.
12.4 Product’s outer packaging shall be labelled with the lot number to facilitate storage
management and product recall.
12.5 Allergen information: Allergen labelling shall comply with the regulations of
the country of origin and the allergen management of sales area.
13 Customer Complaint Procedure and Product Recall
13.1 Customer complaint system shall be established for written or verbal complaints
and suggestions. The quality control personnel (and when necessary, with the
coordination of other relevant departments) shall investigate the root cause and
make improvements, and assign a personnel to contact the customer who filed the
TQF-PCS-016
TQF Management Technical Specifications—Certification Regulation Ver. 2.0
62 / 66 ©Taiwan Quality Food Association
[Canned Food]
complaints or suggestions for explanation (or apologies) or in appreciation for
his/her comments.
13.2 A system for product recall and destruction of finished products shall be
established, including degree of product recall, scope and due date, mock recall
shall be conducted at least once a year.
13.3 The written or oral complaints and suggestions made by the customer and the
finished product recall shall be recorded, indicating product name, lot number,
quantity, reason, handling date and final resolution method. It is recommended that
the records be statistically analyzed and reviewed periodically, and the result
distributed to related departments as a reference for improvement.
13.4 Food factories shall establish anomalies or defect handling procedures to address
significant and potential problems that may arise from external or internal
problems or customer complaints.
14 Record Management
14.1 Records
14.1.1 Sanitation management specialist personnel shall record the result of
regular sanitary inspections, fill out the hygiene management log, which
include daily sanitizing work and personnel hygiene conditions and
detailed records of the corrective actions and preventive measures.
14.1.2 The Quality Assurance Department shall record and review the results
of quality control of raw materials, semi-finished product and finished
product and even the customer complaint and product recall results.
Corrective action and preventive measures shall be recorded in detail.
14.1.3 The Production Department shall complete the production records and
process operation control records, and also corrective action and
preventive measures shall be recorded in detail.
14.1.4 All food factory records and documents shall be presented in Chinese
and truly recorded.
14.1.5 Stationaries that not easy to be erased shall be used for record writing.
Every record shall be signed and dated by responsible persons and
supervisor, signature shall be use in principle, when seal are used
instead then special control procedure shall be established. If the
content of the record are modified, the original text shall not be
TQF-PCS-016
TQF Management Technical Specifications—Certification Regulation Ver. 2.0
63 / 66 ©Taiwan Quality Food Association
[Canned Food]
completely illegible so that the original text cannot be read, the person
who made the modification shall sign next to revised text.
14.2 Record verification All production and quality control records shall be reviewed respectively by the Production and Quality Control Departments to ensure that all operations are in compliance and immediate actions shall be taken whenever an anomaly or deviation is found.
14.3 Recordkeeping All food factory records including inventory regulated under this provision, shall be kept at least 5 years and readily accessible.
15 Establishment of Management System and Auditing
15.1 Food factory shall establish an integral effective TQF management system. The
design and control of the organization and implementation system shall have
structural integrity and coordination.
15.2 Management system audit
15.2.1 Food factory shall establish an effective internal auditing system to
conduct both regular and non-regular audits. The assessment shall be
carried out by all levels of management staffs in order to identify
potential problems of the plant and to give a reasonable solution,
corrective action and tracking.
15.2.2 An internal auditor shall be properly trained, and it shall be documented
and recorded.
15.2.3 Food factory shall establish an effective internal audit plan and specify
the frequency of audits (on a three-month basis), and shall be
effectively implemented and recorded. 15.3 Document management system
15.3.1 Shall establish procedure document which cover the requirements of applied
certification scopes and products, according to safety and quality management
policy.
15.3.2 The issuance, renewal and abrogation of the documentation shall be signed
and approved by responsible person or authorized person for implementing
and recorded.
15.3.3 This is also applicable for revisions that will ensure that the staffs responsible
for the quality operation have the valid version of the operation document and
TQF-PCS-016
TQF Management Technical Specifications—Certification Regulation Ver. 2.0
64 / 66 ©Taiwan Quality Food Association
[Canned Food]
is placed in the workplace for the operator to be implemented. 15.4 Traceability system
15.4.1 Food factory shall establish, implement and maintain a product traceability
system according to “food and its related products traceability system
management approach” enacted by TFDA, with lot number or other trace
back method that can identify the name and address of the production
manufactory. The system should be able to trace back the product from the
customer end to the raw material supplier, and to track forward from the raw
material to the finished product and have them recorded.
15.4.2 The OEM products shall also comply with the requirements of traceability
system in this scheme. 15.5 Emergency procedure
Food factory shall stablish procedures and contingency plans for potential emergencies and conduct regular drills.
15.6 Improvement and update
15.6.1 During the course of operation, improvements shall be made based on
the sanitation issues, and reviewed and discussed with the sanitation
control team. Continuous operation improvement and update shall be
done when necessary in accordance with regulations and TQF
requirements.
15.6.2 During the course of operation, the food factory shall identify
improvement opportunities when problems occurred in the
production process, quality control, management system,
customer complaint, deviation responses, product recall, labeling,
supplier assessment, internal audit and food safety management
system implementation, and reviewed and discussed with the
Quality Management Committee. Continuous operation
improvement and update shall be done when necessary in
accordance with this provision. In the event of a major or sudden
food safety incident, or for any reason the product was removed
from the shelf and recalled, the supplier shall notify Taiwan
Quality Food Association and the certification body with priority.
16 Supplementary Specifications
16.1 When the content of these technical specifications are in conflict with existing
TQF-PCS-016
TQF Management Technical Specifications—Certification Regulation Ver. 2.0
65 / 66 ©Taiwan Quality Food Association
[Canned Food]
national laws and regulations, then the existing laws and regulations shall prevail.
Compliance dates for the implementation of the Food Safety Control System
(HACCP) is subject to the announcements of the central authority. Manufacturers
shall establish the HACCP system before any announcement of the central
authority.
16.2 These technical specifications and its amendment shall come into force from the
date of publication.
TQF-PCS-016
TQF Management Technical Specifications—Certification Regulation Ver. 2.0
66 / 66 ©Taiwan Quality Food Association
[Canned Food]
Figure 4-01. The corner and column feet of the wall shall have an appropriate arc
Wall
3 cm 3 cm 3 cm 3 cm
3 cm
3 cm
Floor
Wall Outer Side Inner Side
Windowsill
Windowsill
Figure 4-02. The angle between interior windowsill and surface level
Surface level