www.tridonic.com 1Subject to change without notice.
Data sheet 07/12-LED078-3
U – LED modules, converters and systemsGENERAL ILLUMINATION
Product description
•Spotlights
•Downlights
•High-flux LED module
•Narrow colour temperature tolerance band
•Lifetime up to 50,000 hours
•Compact design
•Excellent thermal management1
•NTC for temperature control
•High-power LED in chip-on-board technololgy
•Beam characteristic: 140°
•Uniform distribution of light
•Fixing holes for M3 screws
•Connection: Cable 300 mm
•Built-in LED module
•Cooling required
Technical dataBeam characteristic 140°
Ambient temperature ta -30 ... +55 °C
Typ. tc point 65 °C
Weight 0.020 kg
Risk group (EN 62471:2008) 0
ÈStandards, page 2
Colour temperatures and tolerances, page 6, 7
Umodule SPOT P340-3umodule SPOT
NTCNTC
– LED+ LED
1,652,00 typ.
NTC
Ø30
1Ø3
8 2 48
559,
25
14,5
0
21,0
0
27,5
0
34,0
0
40,5
0
45,7
5
0,00
0,003,00
6,00 7,65
40,3542,0045,00
1 Minimal reflector diameter2 Maximum reflector diameter
tc
Ordering dataColour temperature Type Article number
3,000 K LED P340-3 3000K 55x48 89601423
3,500 K LED P340-3 3500K 55x48 89601424
4,000 K LED P340-3 4000K 55x48 89601425
5,000 K LED P340-3 5000K 55x48 89601426
2.700 K LED P340-3 GOLD 55x48 89601595
– LED P340-3 CM+ 55x48 89601596Packaging: 20 pieces/packaging, 360 pieces/carton
Specific technical dataType Photometric
codeTyp. luminous flux at 1,050 mA2 3 4
Typ. luminous flux at 1,400 mA2 3 4
Typ. forward voltage2 3 Power consumptionmodule
Typ. efficacy at 1,050 mA
Colour rendering indexCRI
LED P340-3 3000K 55x48 830/459 2,680 lm 3,350 lm 38.4 V 40.3 W 66 lm/W > 80
LED P340-3 3500K 55x48 835/459 2,680 lm 3,350 lm 38.4 V 40.3 W 66 lm/W > 80
LED P340-3 4000K 55x48 840/459 2,960 lm 3,680 lm 38.4 V 40.3 W 73 lm/W > 80
LED P340-3 5000K 55x48 750/459 3,360 lm 4,190 lm 38.4 V 40.3 W 83 lm/W > 70
LED P340-3 GOLD 55x48 – 2,450 lm 3,000 lm 38.4 V 40.3 W 62 lm/W > 90
LED P340-3 CM+ 55x48 – 2,450 lm 3,000 lm 38.4 V 40.3 W 62 lm/W –All values for ta = 25 °C, tc = 65 °C.
1 If the maximum temperature limits are exceeded, the life of the module will be greatly reduced or the module may be damaged.The temperature of the umodule SPOT at the tc point in the thermally stable state by mean of a temperature sensor or temperature-sensitivesticker as per EN 60598-1. For the precise position of the tc point see the drawing above.
2 At tc = 65 °C.
3 Tolerance range for optical and electrical data: ±15 %.
4 Max. permissible surge current: 3 A, duration max. 10 µs.
PHASED
OUT
www.tridonic.com 2Subject to change without notice.
Data sheet 07/12-LED078-3
U – LED modules, converters and systemsGENERAL ILLUMINATION
Product description
•Housing for LED modul
•Diameter: 65 mm
TALEXXaccessory Cover Spot
ACCE
S-SO
RIES
Ordering DataType Article number
P 340-3 LED cover white D65 LES 30 mm 88167488Packaging: 10 pieces/packaging, 200 pieces/carton
Converter matrix – Umodule SPOT 340-3
REMOTE LCI IN-BUILT LCI
TypeLCI 050/1050
T020LCI 055/1400
T020LCAI 050/1050
T020LCAI 055/1400
T020LCI 050/1050
R010LCI 055/1400
R010LCAI 050/1050
R010LCAI 055/1400
R010
Art. No. 86459218 86459219 86459247 86459248 86459216 86459217 86459245 86459246
Assignable converter Assignable converter
Type Min. Max. Min. Max. Min. Max. Min. Max. Min. Max. Min. Max. Min. Max. Min. Max.
LED P340-3 3000K 55x48 89601423 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
LED P340-3 3500K 55x48 89601424 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
LED P340-3 4000K 55x48 89601425 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
LED P340-3 5000K 55x48 89601426 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
LED P340-3 GOLD 55x48 89601426 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
LED P340-3 CM+ 55x48 89601426 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
WiringCable: AWG24; length 300 mm
pin 1 2 5 6function + - NTC NTCcolour red black grey grey
PHASED
OUT
www.tridonic.com 3Subject to change without notice.
Data sheet 07/12-LED078-3
U – LED modules, converters and systemsGENERAL ILLUMINATION
Typical heat sink surface
NotesThe actual cooling surface can differ because of the material, the structural shape, outside influences and the installation situation. A thermal connection between umodule SPOT and heat sink with heat-conducting paste or heat conducting adhesive film is absolutely necessary.
Umodule SPOT P340-3, 1,050 mAta tc Rth, hs-a
25 °C 65 °C 1.34 K/W30 °C 65 °C 1.15 K/W40 °C 65 °C 0.77 K/W50 °C 65 °C 0.4 K/WFor umodule SPOT P340-3 a tc temperature of 65 °C has to be complied in
order to achieve an optimum between heat sink requirements, light output and life time.
Compliance with the maximum permissible reference temperature at the tc point must be checked under operating conditions in a thermally stable state. The maximum value must be determined under worst-case conditions for the relevant application.
Mounting instruction
umodule SPOT from Tridonic which have to be installed on a heat sink have to be connected with heat-conducting paste or heat conducting adhesive film and fixed with M3 screws with plastic washer.
The fixing/cooling surface must be cleaned before installing the u modules to remove all dirt, dust and grease.
None of the components of the umodule SPOT (substrate, LED, electronic components etc.) may be exposed to tensile or compressive stresses.
Thermal design and heat sinkThe rated life of u products depends to a large extent on the temperature. If the permissible temperature limits are exceeded, the life of the umodule SPOT will be greatly reduced or the umodule SPOT may be destroyed.
Therefore the umodule SPOT P340-3 needs to be mounted onto a heat sink.
Tridonic’s excellent thermal design for the umodule SPOT products provides the lowest thermal resistance and therefore allowing new compact designs without sacrificing quality, safety and life time.
tc point, ambient temperature and lifetimeThe temperature at tc reference point is crucial for the light output and life time of a u product.
Thermal behaviour
storage temperature -30 – 85 °Coperating temperature -30 – 55 °Ctc max. (at typ. current) 85 °C
StandardsEN 62031EN 62471
Umodule SPOT P340-3, 1,400 mAta tc Rth, hs-a
25 °C 65 °C 0.96 K/W30 °C 65 °C 0.82 K/W40 °C 65 °C 0.54 K/W50 °C 65 °C 0.25 K/W
0
200
400
600
800
1000
1200
1400
1600
0 10 20 30 40 50 60 70 80 90 100Tc [°C]
If [m
A]
0
20
40
60
80
100
120
140
160
180
200
30 40 45 55 70Temperature [°C]
Resi
stan
ce [k
Ω]25 656035 50 75
220
240
80 85
Temperature controlAn NTC resistor is on the board of the umodule SPOT P340-3 to control the tc temperature during the operation.Exact position see drawing on page 1.The details of the 220 kΩ NTC (order number B57431V2223J062) you can find in the data sheet of the manufacturer AVX (Nr. NB12QØØ224).
EOS/ESD safety guidelines
The device / module contains components that are sensitive to electro-static discharge and may only be installed in the factory and on site if appropriate EOS/ESD protection measures have been taken. No special measures need be taken for devices/modules with enclosed casings (contact with the pc board not possible), just normal installation prac-tice. Please note the requirements set out in the document EOS / ESD guidelines (Guideline_EOS_ESD.pdf) at: http://www.tridonic.com/com/en/technical-docs.asp
1st digit 2nd + 3rd digit 4th digit 5th digit 6th digit
Code CRIColour temperature in
Kelvin x 100McAdams
initial
McAdams after 25% of the
lifetime (max.6000h)
Lumen maintanance after 25% of the lifetime (max.6000h)
Code Remaining lumen7 67 – 76 7 ≥ 70 %8 77 – 86 8 ≥ 80 %9 87 – ≥90 9 ≥ 90 %
Photometric code
Key for photometric code, e. g. 830 / 559
PHASED
OUT
www.tridonic.com 4Subject to change without notice.
Data sheet 07/12-LED078-3
U – LED modules, converters and systemsGENERAL ILLUMINATION
Electrical supply/choice of converterumodule SPOT from Tridonic are not protected against overvoltages, overcurrents, overloads or short-circuit currents. Safe and reliable operation can only be guaranteed in conjunction with a converter which complies with the relevant standards. The use of u converters from Tridonic in combination with umodule SPOT guarantees the necessary protection for safe and reliable operation.
If a converter other than Tridonic uconverter is used, it must provide the follow-ing protection:•Short-circuitprotection•Overloadprotection•Overtemperatureprotection
umodule SPOT P340-3 must be supplied by a constant current converter.Operation with a constant voltage converter will lead to an irreversible damage of the module.
Wrong polarity can damage the umodule SPOT P340-3.
Lumen maintenance
tc temperature in °C luminous flux in % operating time in h
2580 60,00070 81,00050 132,000
4580 44,00070 64,00050 110,000
6580 32,00070 50,00050 91,000
7580 25,00070 41,00050 81,000
f(soldering time) for the modules
Temperature Max. timewithout heat sink
Max. timewith optimized heat sink
330 °C 15 s –340 °C 12 s –350 °C 10 s –360 °C 5 s 15 s370 °C 3 s 12 s380 °C 2 s 10 s390 °C 1 s 5 s
Matrix temperature
The values apply for soldering without heat sink. To reduce the duration of soldering it is recommended to pre-heat the module at ta max., e.g. on a plate.
PHASED
OUT
www.tridonic.com 5Subject to change without notice.
Data sheet 07/12-LED078-3
U – LED modules, converters and systemsGENERAL ILLUMINATION
The diagrams based on statistic values.The real values can be different.
0,80
0,85
0,95
1,00
current [mA]
rel.
volta
ge [a
. u.]
Relative forward voltage at tc = 65 °C
600200
1,10
140012001000800400
0,90
1,05
1600
0,20
0,40
0,80
1,00
current [mA]
rel.
lum
inou
s flu
x [a
. u.]
Relative luminous flux at tc = 65 °C
600200
1,40
140012001000800400
0,60
1,20
1600
Relative forward voltage and relative luminous flux
0,97
0,98
0,99
1
1,01
1,02
1,03
1,04
1,05
20 30 40 50 60 70Tc [°C]
rel.
volta
ge [a
.u.]
80 85
0,92
0,94
0,96
0,98
1
1,02
1,04
1,06
1,08
1,1
1,12
1,14
30 40 50 60 85Tc [°C]
rel.
lum
inou
s flu
x [a
.u.]
20 8070
Optical characteristics Umodule SPOT P340-3
The optical design of the umodule SPOT product line ensures optimumhomogenity for the light distribution.
Umodule SPOT P340-3 140°: Light distribution
0°
20
20
-20 40
40
60
60
80
100
80 100-40-60-80-100
10°-10° 20°-20°-30°
-40°
-50°
-60°
30°
40°
50°
60°
70°
80°
90°-90°0
rela
tive
inte
nsity
Iv/Iv
,max PHASED
OUT
www.tridonic.com 6Subject to change without notice.
Data sheet 07/12-LED078-3
U – LED modules, converters and systemsGENERAL ILLUMINATION
Coordinates and tolerances according to CIE 1964
The specified colour coordinates are measured by a current impulse of 1,050 mA and a duration of 100 ms.The ambient temperature of the measurement is ta = 25 °C.The measurement tolerance of the colour coordinates are ± 0.01.
MacAdam ellipse: 4SDCM
MacAdam ellipse: 4SDCM
0,3700
0,3750
0,3800
0,3850
0,3900
0,3950
0,4000
0,4050
0,4100
0,39
50
0,40
00
0,40
50
0,41
00
0,41
50
0,42
00
0,42
50
0,43
00
0,43
50
0,3800
0,3850
0,3900
0,3950
0,4000
0,4050
0,4100
0,4150
0,4200
0,42
50
0,43
00
0,43
50
0,44
00
0,44
50
0,45
00
0,45
50
0,46
00
0,46
50
3,000 Kx0 y0
Centre 0,4460 0,3990
3,500 Kx0 y0
Centre 0,4160 0,3900
380 420 460 500 540 580 620 660 700 740 780
wave length [nm]
norm
. int
ensi
ty [%
]
0
20
40
60
80
100
380 420 460 500 540 580 620 660 700 740 780wave length [nm]
norm
. int
ensi
ty [%
]
0
20
40
60
80
100
PHASED
OUT
www.tridonic.com 7Subject to change without notice.
Data sheet 07/12-LED078-3
U – LED modules, converters and systemsGENERAL ILLUMINATION
MacAdam ellipse: 4SDCM
0,3450
0,3500
0,3550
0,3600
0,3650
0,3700
0,3750
0,3800
0,3350
0,3400
0,3450
0,3500
0,3550
0,3600
0,3650
0,3700
0,3750
0,3400
5,000 Kx0 y0
Centre 0,3530 0,3590
380 420 460 500 540 580 620 660 700 740 780wave length [nm]
norm
. int
ensi
ty [%
]
0
20
40
60
80
100
MacAdam ellipse: 4SDCM
0.3600
0.3650
0.3700
0.3750
0.3800
0.3850
0.3900
0.3950
0.4000
0.36
50
0.37
00
0.37
50
0.38
00
0.38
50
0.39
00
0.39
50
0.40
00
0.40
50
4,000 Kx0 y0
Centre 0,3860 0,3780
380 420 460 500 540 580 620 660 700 740 780
wave length [nm]
norm
. int
ensi
ty [%
]
0
20
40
60
80
100
MacAdam ellipse: 4SDCM
0,4000
0,4050
0,4100
0,4150
0,4200
0,4250
0,4300
0,4350
0,4400
0,45
00
0,45
50
0,46
00
0,46
50
0,47
00
0,47
50
0,48
00
0,48
50
0,49
00
GOLDx0 y0
Centre 0,4700 0,4160
380 420 460 500 540 580 620 660 700 740 7800
20
40
60
80
100
wave length [nm]
norm
. int
ensi
ty [%
]PHASED
OUT
www.tridonic.com 8Subject to change without notice.
Data sheet 07/12-LED078-3
U – LED modules, converters and systemsGENERAL ILLUMINATION
MacAdam ellipse: 4SDCM
0,2900
0,2950
0,3000
0,3050
0,3100
0,3150
0,3200
0,3250
0,3300
0,37
50
0,38
00
0,38
50
0,39
00
0,39
50
0,40
00
0,40
50
0,41
00
0,41
50
CM+x0 y0
Centre 0,3940 0,3070
380 420 460 500 540 580 620 660 700 740 7800
20
40
60
80
100
wave length [nm]
norm
. int
ensi
ty [%
]
PHASED
OUT
Top Related