TECHNICAL MANUAL

Of

Intel H110 Express Chipset

Based Mini-ITX M/B

NO. G03-NC5D-F

Revision: 2.0

Release date: October 1, 2019

Trademark:

* Specifications and Information contained in this documentation are furnished for information use only, and are

subject to change at any time without notice, and should not be construed as a commitment by manufacturer.

i

Environmental Protection Announcement Do not dispose this electronic device into the trash while discarding. To minimize pollution and ensure environment protection of mother earth, please recycle.

ii

ENVIRONMENTAL SAFETY INSTRUCTION ...................................................................... iii USER’S NOTICE .................................................................................................................. iv MANUAL REVISION INFORMATION .................................................................................. iv ITEM CHECKLIST ................................................................................................................ iv CHAPTER 1 INTRODUCTION OF THE MOTHERBOARD 1-1 FEATURE OF MOTHERBOARD ................................................................................ 1 1-2 SPECIFICATION ......................................................................................................... 2 1-3 LAYOUT DIAGRAM .................................................................................................... 3 CHAPTER 2 HARDWARE INSTALLATION 2-1 JUMPER SETTING ..................................................................................................... 8 2-2 CONNECTORS AND HEADERS ................................................................................ 11 2-2-1 CONNECTORS ............................................................................................. 11 2-2-2 HEADERS ..................................................................................................... 14

CHAPTER 3 INTRODUCING BIOS 3-1 ENTERING SETUP ..................................................................................................... 20 3-2 BIOS MENU SCREEN ................................................................................................ 21 3-3 FUNCTION KEYS ....................................................................................................... 21 3-4 GETTING HELP .......................................................................................................... 22 3-5 MENU BARS ............................................................................................................... 22 3-6 MAIN MENU ................................................................................................................ 23 3-7 ADVANCED MENU ..................................................................................................... 24 3-8 CHIPSET MENU .......................................................................................................... 31 3-9 SECURITY MENU ....................................................................................................... 33 3-10 BOOT MENU ............................................................................................................... 34 3-11 SAVE & EXIT MENU ................................................................................................... 36

TABLE OF CONTENT

iii

Environmental Safety Instruction Avoid the dusty, humidity and temperature extremes. Do not place the product in

any area where it may become wet. 0 to 40 centigrade is the suitable temperature. (The temperature comes from the

request of the chassis and thermal solution) Generally speaking, dramatic changes in temperature may lead to contact

malfunction and crackles due to constant thermal expansion and contraction from the welding spots’ that connect components and PCB. Computer should go through an adaptive phase before it boots when it is moved from a cold environment to a warmer one to avoid condensation phenomenon. These water drops attached on PCB or the surface of the components can bring about phenomena as minor as computer instability resulted from corrosion and oxidation from components and PCB or as major as short circuit that can burn the components. Suggest starting the computer until the temperature goes up.

The increasing temperature of the capacitor may decrease the life of computer.

Using the close case may decrease the life of other device because the higher temperature in the inner of the case.

Attention to the heat sink when you over-clocking. The higher temperature may

decrease the life of the device and burned the capacitor.

iv

USER’S NOTICE COPYRIGHT OF THIS MANUAL BELONGS TO THE MANUFACTURER. NO PART OF THIS MANUAL, INCLUDING THE PRODUCTS AND SOFTWARE DESCRIBED IN IT MAY BE REPRODUCED, TRANSMITTED OR TRANSLATED INTO ANY LANGUAGE IN ANY FORM OR BY ANY MEANS WITHOUT WRITTEN PERMISSION OF THE MANUFACTURER.

THIS MANUAL CONTAINS ALL INFORMATION REQUIRED TO USE THIS MOTHER-BOARD SERIES AND WE DO ASSURE THIS MANUAL MEETS USER’S REQUIREMENT BUT WILL CHANGE, CORRECT ANY TIME WITHOUT NOTICE. MANUFACTURER PROVIDES THIS MANUAL “AS IS” WITHOUT WARRANTY OF ANY KIND, AND WILL NOT BE LIABLE FOR ANY INDIRECT, SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES (INCLUDING DAMAGES FOR LOSS OF PROFIT, LOSS OF BUSINESS, LOSS OF USE OF DATA, INTERRUPTION OF BUSINESS AND THE LIKE).

PRODUCTS AND CORPORATE NAMES APPEARING IN THIS MANUAL MAY OR MAY NOT BE REGISTERED TRADEMARKS OR COPYRIGHTS OF THEIR RESPECTIVE COMPANIES, AND THEY ARE USED ONLY FOR IDENTIFICATION OR EXPLANATION AND TO THE OWNER’S BENEFIT, WITHOUT INTENT TO INFRINGE.

Manual Revision Information Reversion Revision History Date 2.0 Second Edition October 1, 2019

Item Checklist Motherboard Cable(s) I/O Back panel shield

1

Chapter 1 Introduction of the Motherboard

1-1 Feature of Motherboard Intel® H110 express chipset Support LGA 1151 CPU socket Intel® Core™ i7 processors / Intel® Core™ i5

processors / Intel® Core™ i3 processors / Intel® Pentium™ processors , Intel® Celeron™ processors

Support 1 * DDR3L 1666/1333 MHz SO-DIMM up to 8 GB, Integrated with 2* Intel i211AT Gigabit Ethernet LAN chip Integrated with RealTek 4-CH HD Audio Codec

Support USB 3.0 data transport demand Support 2 * SATAIII (6Gb/s) Devices Support 4* HDMI & 1* DP multi-display (NVIDIA Surround™) Support 2* full-size Mini-PCIE slot(one share with MSATA function) Support Smart FAN function

Supports ACPI S3 Function Compliance with ErP Standard Support Watchdog Timer Technology

2

1-2 Specification Spec Description Design 6-Layer PCB; Size: 18.0 x 22.0cm Chipset Intel H110 Express Chipset

CPU Socket

Support Intel® LGA 1151 Socket Core™ i7 processors, Intel® Core™ i5 processors, Intel® Core™ i3 processors, Intel® Pentium™ processors, Intel® Celeron™ processors

* for detailed CPU support information please visit our website GPU Onboard Nvidia GTX950 + 2GB DDR5 Memory

Memory Slot 1*DDR3L SO-DIMM slot Support DDR3L 1600/1333 MHz SO-DIMM up to 8GB

Expansion Slot 1* Full-size Mini-PCIE slot (MPE1) 1* Full-size Mini-PCIE/ MSATA shared slot (MINIPCIE/SATA) 1* SIM slot

Storage 2* SATA III 6G/s connector 1 * full-size Mini-PCIE/ MSATA shared slot (MINIPCIE/SATA)

Gigabit LAN Chip Integrated with 2* Intel i211AT Gigabit PCI-E LAN chip Support Fast Ethernet LAN function of providing

10/100/1000Mbps Ethernet data transfer rate

Audio Chip Realtek 4-CH HD Audio Codec integrated Audio driver and utility included

BIOS AMI 64Mb Flash ROM Multi I/O Rear Panel I/O:

1* 19V DC-in system power connector 3* HDMI port 1* Display port 1* USB 2.0 port & 2* USB 3.0 port 2* RJ-45 LAN port 1* Line-Out port &1* MIC port

3

Internal I/O Connectors& Headers: 1 *4-pin SATA HDD power-out connector 5* FAN connector 1*Front panel audio header 1* HDMI_SPDIF out header 1* SPEAK_CON header 1*Front panel header 1 * 4-Pin USB 2.0 header for 1* USB 2.0/1.1 port 1 * 9-Pin USB 2.0 header for 2* USB 2.0/1.1 port 1 * 19-Pin USB 3.0 header for 2* USB 3.0 port 1 * PS2 Keyboard & Mouse header 1* GPIO header 2* RS232 Serial port header (COM1/2) 1* HDMI port header

1-3 Layout Diagram

Rear IO Diagram

MIC-IN

Line-OUT 19V DC-in

Power Connector

HDMI Port (HDMI1)

HDMI Port (HDMI2)

Display Port

USB 2.0 Port

USB 3.0 Ports

HDMI Port (HDMI4)

RJ-45 LAN Ports (LAN1/2)

4

Motherboard Internal Diagram-Front

Intel H110 Chipset

LGA 1151 CPU Socket

GPU

DDR3L SODIMM Slot (SODIMM1)

*Full-size Mini-PCIE/MSATA Slot

(MINIPCIE/MSATA)

*Full-size Mini-PCIE Slot

(MPE)

Serial Port Headers (COM1/COM2)

HDMI Port Header

PS/2 Keyboard & Mouse Header

SATAIII Ports (SATA1/2)

GPIO Header

CHAFAN1 Header

SYSFAN1 Header

CPUFAN1 Header

Front Panel Header

GPUFAN1 Header

USB 3.0 Port Header

USB 2.0 Port Header

19V DC-in Power Connector

HDMI Port (HDMI1)

HDMI Port (HDMI2)

Display Port

USB 2.0 Port

USB 3.0 Ports

RJ-45 LAN Ports (LAN1/2)

Line-OUT

MIC-IN

HDMI Port (HDMI4)

Front Panel Audio Header SPEAK_CON

HDMI_SPDIF out

Header

USB 2.0 Port Header

SATA HDD Power-Out Connector

GPUFAN2 Header

5

Motherboard Internal Diagram--Back

Note: SIM card slot only work when compatible SIM card installed & 3G LAN card installed in MPE1 Mini-PCIE slot.

SIM Card Slot

6

Motherboard Jumper Position

AT_MODE

JP1

COPEN1

JP2

JBAT

7

Connectors Connector Name

DC19V_IN1 19V DC-in Power Connector HDMI1/2/4 HDMI Port Connector x3 DP1 Display Port Connector USB1 USB 2.0 Port Connector USB3_1 USB 3.0 Port Connector x2 LAN1/2 RJ-45 LAN Connector x2 LINE_OUT Audio Line-Out Connector MIC Audio MIC Connector SATA1/2 SATAIII Connector x2 PWROUT1 SATA HDD Power-out Connector CPUFAN1/GPUFAN1/GPUFAN2/SYSFAN1 /CHAFAN1

Fan Connector x4

MINIPCIE/SATA Full-size Mini-PCIE/MSATA Slot MPE1 Full-size Mini-PCIE Slot

Headers Header Name Description

FP_AUDIO Front Panel Audio Header 9-pin Block HDMI_SPDIF HDMI_SPDIF Out Header 2-pin Block SPEAK_CON1 Speaker Header 4-pin Block JW_FP1

Front Panel Header(PWR LED/ HD LED/Power Button /Reset)

9-pin Block

GPIO1 GPIO Header 10-pin Block PS2_CON1 PS2 Keyboard & Mouse Header 6-pin Block COM1/2 Serial Port Header 9-pin Block HDMI3 HDMI Port Header 20-pin Block FP_USB1 USB 2.0 Port Header 9-pin Block FP_USB2 USB 2.0 Port Header 4-pin Block

8

USB3_2 USB 3.0 Port Header 19-pin Block

Jumper Jumper Name Description

AT_MODE ATX Mode / AT Mode Select 2-pin Block JP2 MPE Slot Power VCC 3.3V/3.3VSB Select 3-pin Block JP1 ME_Features Select 2-pin Block JBAT Clear CMOS RAM Settings 2-pin Block COPEN1 Case Open Message Display Function 2-pin Block

Chapter 2

Hardware Installation 2-1 Jumper Setting AT_MODE (3-pin): ATX Mode/ AT Mode Select

2-3 Closed: AT Mode Selected.

AT_MODE→ATX/AT Mode Select

1-2 Closed: ATX Mode Selected (Default);

1

3

1

3

*ATX Mode Selected: Press power button to power on after power input ready; AT Mode Selected: Directly power on as power input ready.

9

JP2 (3-pin): MPE Slot VCC 3.3V/3.3 VSB Select

2-3 Closed: MPE Slot VCC= 3.3VSB.

JP2→MPE Slot VCC

1-2 Closed: MPE Slot VCC= 3.3V;

1

3

1

3

JP1 (2-pin): ME Features Select

1 2

1 2

JP1→ME Features Select

1-2 Open: Enable ME Features；

1-2 Closed: Disable ME Features.

10

JBAT (2-pin): Clear CMOS RAM Settings

1

1

JBAT→Clear CMOS

1-2 Open: Normal (Default);

1-2 Closed:Clear CMOS Settings.

2

2

COPEN1 (2-pin):Case Open Message Display Function Select

1 2

1 2

COPEN1→Case Open Detect

1-2 Open: Normal (Default);

1-2 Close: Case Open Detect Function Selected(One Touch).

Pin (1-2) Close: When Case open function pin short to GND, the Case open function was detected. When Used, needs to enter BIOS and enable ‘Case Open Detect’ function. In this case if your case is removed, next time when you restart your computer, a message will be displayed on screen to inform you of this.

11

2-2 Connectors and Headers 2-2-1 Connectors (1) Rear Panel Connectors

* For I/O diagram please refer to page-3. Icon Name Function

19V DC-in Power Jack Connector

For user to connect compatible power adapter to provide power supply for the system.

HDMI Port To connect display device that support HDMI specification.

Display Port To the system to corresponding display device with compatible display port cable.

Display Port To the system to corresponding display device with compatible display port cable.

USB 2.0 Port To connect USB keyboard, mouse or other devices compatible with USB specification.

USB 3.0 Port To connect USB keyboard, mouse or other devices compatible with USB specification. USB 3.0 ports supports up to 5Gbps data transfer rate.

RJ-45 LAN Port

This connector is standard RJ-45 LAN jack for Network connection.

Line-Out Connector

For user to connect external speaker, earphones, etc. to transfer system audio output.

MIC Connector

User can connect microphone device to this port.

12

(2) SATA1/SATA2 (7-pin): SATA III Port connector

SATA1&SATA2 are high-speed SATAIII port that supports 6 GB/s transfer rate.

Pin No. Definition

1 GND 2 TXP 3 TXN 4 GND 5 RXN 6 RXP 7 GND

(3) PWROUT1(4-pin): SATA HDD Power-out Connector

Pin No. Definition

1 +5V 2 GND 3 GND 4 +12V

13

(4) CPUFAN1/GPUFAN1/GPUFAN2(4-pin):Fan Connector

(5) SYSFAN1/CHAFAN1(3-pin):Fan Connector

14

2-2-2 Headers (1) FP_AUDIO (9-pin): Line-Out, MIC-In Header This header connects to Front Panel Line-out, MIC-In connector with cable.

MIC2_L MIC2_R

LINE_OUT_R

SENSE

MIC_JD

Pin 1

2 GND DETECT

LINE_OUT_L LINE_OUT_JD

(2) HDMI_SPDIF(2-pin): HDMI-SPDIF Out header

Pin1

SP

DIF

_OU

T

GN

D

15

(3) SPEAK_CON1 (4-pin block): Speaker Header

(4) JW_FP1 (9-pin): Front Panel Header

HDD LED+

GND

HDD LED- GND

RSTSW

PWRBTN

Pin 1

2

VCC

PWR LED+ PWR LED -

16

(5) GPIO1(10-pin): GPIO Header

Pin 1

GPIO_31

2

GPIO_37

GPIO_35 GPIO_33

VCC

GPIO_30

GPIO_36

GPIO_34

GPIO_32

GND

(6) PS2_CON1 (6-pin): PS/2 Keyboard & Mouse Header

Pin 1

KB_CLK

MS_CLK

VCC

GND

KB_DATA

MS_DATA

17

(7) COM1/COM2 (9-Pin): RS232 Serial Port Header

DC

D

Pin1 Pin6

SIN

S

OU

T

DT

R

GN

D

DS

R

RT

S

CT

S

RI

(8) HDMI3(20-Pin): HDMI Port Header

Pin 1

11

GND

20

2

HDMI_TXP1

HDMI_TXN1

GND

HDMI_TXCP HDMI_TXCN

HDMI_SDA HDMI_+5V

GND

HDMI_TXP2 HDMI_TXN2 GND

HDMI_TXP0

HDMI_TXN0

GND

NC

HDMI_SCL GND

HDMI_HPD

NC

18

(9) FP_ USB1(9-pin): USB 2.0 Port Header

VCC

NC

+DATA

Pin 1

-DATA VCC

GND GND +DATA -DATA

2

(10) FP_ USB2(9-pin): USB 2.0 Port Header

19

(11) USB3_2 (19-Pin): USB 3.0 Port Header

SSTX1+

Pin 1

10

D1+

D1-

GND1

NC

GND2

GND3

VBUS2

SSRX2-

SSRX2+

SSTX2-

SSTX2+

D2 - D2+

SSTX1-

GND0

SSRX1+

SSRX1-

20

VBUS

11

20

Chapter 3 Introducing BIOS

Notice! The BIOS options in this manual are for reference only. Different configurations may lead to difference in BIOS screen and BIOS screens in manuals are usually the first BIOS version when the board is released and may be different from your purchased motherboard. Users are welcome to download the latest BIOS version form our official website.

The BIOS is a program located on a Flash Memory on the motherboard. This program is a bridge between motherboard and operating system. When you start the computer, the BIOS program will gain control. The BIOS first operates an auto-diagnostic test called POST (power on self test) for all the necessary hardware, it detects the entire hardware device and configures the parameters of the hardware synchronization. Only when these tasks are completed done it gives up control of the computer to operating system (OS). Since the BIOS is the only channel for hardware and software to communicate, it is the key factor for system stability, and in ensuring that your system performance as its best.

3-1 Entering Setup Power on the computer and by pressing <Del> immediately allows you to enter Setup. If the message disappears before your respond and you still wish to enter Setup, restart the system to try again by turning it OFF then ON or pressing the “RESET” button on the system case. You may also restart by simultaneously pressing <Ctrl>, <Alt> and <Delete> keys. If you do not press the keys at the correct time and the system does not boot, an error message will be displayed and you will again be asked to Press <Del> to enter Setup

21

3-2 BIOS Menu Screen The following diagram show a general BIOS menu screen:

BIOS Menu Screen

3-3 Function Keys In the above BIOS Setup main menu of, you can see several options. We will explain these options step by step in the following pages of this chapter, but let us first see a short description of the function keys you may use here: Press←→ (left, right) to select screen;

Menu Bar

Menu Items Current Setting Value

Function Keys

General Help Items

22

Press ↑↓ (up, down) to choose, in the main menu, the option you want to confirm or to modify.

Press <Enter> to select. Press <+>/<–> keys when you want to modify the BIOS parameters for the active

option. [F1]: General help. [F2]: Previous values. [F3]: Optimized defaults. [F4]: Save & Reset. Press <Esc> to exit from BIOS Setup.

3-4 Getting Help Main Menu The on-line description of the highlighted setup function is displayed at the top right corner the screen.

Status Page Setup Menu/Option Page Setup Menu Press F1 to pop up a small help window that describes the appropriate keys to use and the possible selections for the highlighted item. To exit the Help Window, press <Esc>.

3-5 Menu Bars There are six menu bars on top of BIOS screen:

Main To change system basic configuration Advanced To change system advanced configuration Chipset To change chipset configuration Security Password settings Boot To change boot settings Save & Exit Save setting, loading and exit options.

23

User can press the right or left arrow key on the keyboard to switch from menu bar. The selected one is highlighted.

3-6 Main Menu Main menu screen includes some basic system information. Highlight the item and then use the <+> or <-> and numerical keyboard keys to select the value you want in each item.

System Date Set the date. Please use [Tab] to switch between date elements. System Time Set the time. Please use [Tab] to switch between time elements.

24

3-7 Advanced Menu

► ACPI Settings

Press [Enter] to make settings for the following sub-items: ACPI Settings Enable Hibernation The optional settings: [Enabled]; [Disabled]. Use this item to enable or disable system ability to hibernate (OS/S4 Sleep State). This option may not be effective with some OS. ACPI Sleep State Use this item to select the highest ACPI sleep state the system will enter when the suspend button is pressed.

25

The optional settings are: [Suspend Disabled]; [S3 (Suspend to RAM)]. ERP Support The optional settings: [Disabled]; [Enabled]. Use this item to enable or disable ERP function for this board. This item should be set as [Disabled] if you wish to have active all Wake-up functions. Wake-Up by PCIE/LAN from S5 The optional settings: [Disabled]; [Enabled]. Use this item to enable or disable wake-up by PCIE/LAN from S5. *This item will only show when ‘ERP Support’ is set as [Disabled]. Wake-Up by PS/2 Keyboard The optional settings: [Disabled]; [Enabled]. Use this function to enable or disable PS/2 keyboard wake-up from S3/S4/S5. *This item will only show when ‘ERP Support’ is set as [Disabled]. Wake-Up by PS/2 Mouse The optional settings: [Disabled]; [Enabled]. Use this function to enable or disable PS/2 mouse wake-up from S3/S4/S5. *This item will only show when ‘ERP Support’ is set as [Disabled]. PWRON After PWR-Fail The optional settings: [Former-Sts]; [Always On]; [Always Off]. RTC WakeUp Use this item to enable or disable system wake on alarm event. The optional settings: [Disabled]; [Fixed Time]; [Dynamic Time]. When set as [Fixed Time], system will wake on the hour/min/sec specified. When set as [Dynamic Time], system will wake on the current time + increased minute(s).The setting range is from [1] to [255].

► PCH-FW Configuration Press [Enter] to view ME information and make settings in the following sub-items: ME FW Image Re-Flash Use this item to enable or disable ME FW Image Re-Flash function. The optional settings: [Disabled]; [Enabled]. * In the case that user needs to update ME firmware, user should set ‘ME FW

26

Image Re-Flash’ as [Enabled], save the settings and exit. The system will turn off and reboot after 4 seconds. If the user goes to BIOS screen again will find this item is set again as [Disabled], but user can still re-flash to update firmware next time.

► Super I/O Configuration Press [Enter] to make settings for the following sub-items: Super IO Configuration ► Serial Port 1 Configuration Press [Enter] to make settings for the following items: Serial Port Use this item to enable or disable serial port (COM). Change Settings Use this item to select an optimal setting for super IO device. Transmission Mode Select The optional settings are: [RS232]; [[RS485/RS422]. ► Serial Port 2 Configuration Press [Enter] to make settings for the following sub-items: Serial Port Use this item to enable or disable serial port (COM). Change Settings Use this item to select an optimal setting for super IO device. WatchDog Timer Use this item to enable or disable WatchDog Timer function. The optional settings: [Disabled]; [Enabled]. When set as [Enabled], the following sub-items shall appear: WatchDog Timer Value User can set a value in the range of [4] to [255]. WatchDog Timer Unit The optional settings are: [Sec.]; [Min.]. Case Open Detect Use this item to detect case has already open or not, show message in POST. The optional settings: [Disabled]; [Enabled].

27

► H/W Monitor Press [Enter] to view current hardware health status, make further settings in ‘CPUFAN Smart Mode’ and ‘GPUFAN1 Smart Mode’.

CPUFAN Smart Mode/GPUFAN1 Smart Mode The optional settings are: [Disabled]; [Enabled]. When set as [Enabled], the following sub-items shall appear: CPUFAN / GPUFAN1 Full-Speed Temperature Use this item to set CPUFAN/GPUFAN1 full speed temperature. Fan will run at full speed when above this pre-set temperature. CPUFAN / SYSFAN Idle-Speed Temperature Use this item to set CPUFAN/GPUFAN1 idle speed temperature. Fan will run at idle speed when below this pre-set temperature.

► CPU Configuration Press [Enter] to view current CPU configuration and make settings for the following sub-items: Intel Virtualization Technology The optional settings: [Enabled]; [Disabled]. When set as [Enabled], a VMM can utilize the additional hardware capabilities provided by Vanderpool Technology. Hardware Prefetcher Use this item to turn on/off the MLC streamer prefecher. The optional settings: [Disabled]; [Enabled]. Adjacent Cache Line Prefetch Use this item to turn on/off prefeching of adjacent cache lines. The optional settings: [Disabled]; [Enabled]. Intel(R) SpeedStep(tm) This item allows more than two frequency ranges to be supported. The optional settings: [Disabled]; [Enabled]. When set as [Enabled], user can make further settings in ‘Turbo Mode’.

Turbo Mode Use this item to enable or disable Turbo Mode. The optional settings: [Disabled]; [Enabled].

28

CPU C states Use this item to enable or disable CPU C states. The optional settings: [Disabled]; [Enabled]. When set as [Enabled], user can make further settings in ‘Package C State limit’. Package C State Limit The optional settings are: [C0/C1]; [C2]; [C3]; [C6]; [C7]; [C7s]; [C8]; [AUTO].

► Intel RMT Configuration Press [Enter] to go to next screen to enable or disable ‘Intel Ready Mode Technology’. Intel Ready Mode Technology The optional settings: [Disabled]; [Enabled]. *When set as [Enabled], user can also make further settings in the following items that appear:

Intel RMT State Use this item to enable or disable Intel RMT enabling status in BIOS.

► SATA Configuration Press [Enter] to make settings for the following sub-items: SATA Controller(s) Use this item to enable or disable SATA device. The optional settings: [Enabled]; [Disabled]. *When set as [Enabled], user can make further settings in the following sub-items: SATA Mode Selection Use this item to determine how SATA controller(s) operate. The optional settings are: [IDE]; [AHCI]. Smart Self Test Use this function to run SMART self test on all HDDs during POST. The optional settings are: [Disabled]; [Enabled]. SATA 1/SATA2 Port 0/ Port1 The optional settings: [Disabled]; [Enabled]. Use this item to enable or disable each SATA port.

29

Hot Plug The optional settings: [Disabled]; [Enabled]. Use this item to designate this port as Hot Pluggable. MSATA1 Port2 The optional settings: [Disabled]; [Enabled]. Use this item to enable or disable device connected to mSATA.

► Network Stack Configuration Press [Enter] to go to ‘Network Stack’ screen to make further settings. Network Stack Use this item to enable or disable UEFI Network Stack. The optional settings: [Disabled]; [Enabled]. When set as [Enabled], the following sub-items shall appear: Ipv4 PXE Support The optional settings are: [Disabled]; [Enabled]. Use this item to enable Ipv4 PXE Boot Support. When set as [Disabled], Ipv4 boot option will not be created. Ipv6 PXE Support The optional settings are: [Disabled]; [Enabled]. Use this item to enable Ipv6 PXE Boot Support. When set as [Disabled], Ipv6 boot optional will not be created. PXE boot wait time Use this item to set wait time to press [ESC] key to abort the PXE boot. Media Detect Count Use this item to set number of times presence of media will be checked.

► CSM Configuration Press [Enter] to make settings for the following sub-items: CSM Support Use this item to enable or disable CSM Support The optional settings are: [Disabled]; [Enabled]. Boot option filter Use this item to control Legacy/UEFI ROMs priority.

30

The optional settings are: [UEFI and Legacy]; [Legacy only]; [UEFI only]. Storage This option controls the execution of UEFI and Legacy Storage OpROM. The optional settings are: [Do not launch]; [UEFI]; [Legacy]. Video Use this item to control the execution of UEFI and Legacy video OpROM. The optional settings are: [Do not launch]; [UEFI]; [Legacy]. Other PCI devices This item is for PCI devices other than Network, Mass storage or video defines which OpROM to launch. The optional settings are: [Do not launch]; [UEFI]; [Legacy].

► USB Configuration Press [Enter] to make settings for the following sub-items: USB Configuration Legacy USB Support The optional settings are: [Enabled]; [Disabled]; [Auto]. [Enabled]: To enable legacy USB support. [Disabled]: to keep USB devices available only for EFI specification, [Auto]: To disable legacy support if no USB devices are connected. XHCI Hand-off This is a workaround for OSes without XHCI hand-off support. The XHCI ownership change should be claimed by XHCI driver. The optional settings are: [Enabled]; [Disabled]. USB Mass Storage Driver Support The optional settings are: [Disabled]; [Enabled]. USB hardware delay and time-out USB transfer time-out Use this item to set the time-out value for control, bulk, and interrupt transfers. The optional settings are: [1 sec]; [5 sec]; [10 sec]; [20 sec]. Device reset time-out Use this item to set USB mass storage device start unit command time-out. The optional settings are: [10 sec]; [20 sec]; [30 sec]; [40 sec].

31

Device power-up delay Use this item to set maximum time the device will take before it properly reports itself to the host controller. ‘Auto’ uses default value: for a root port it is 100 ms, for a hub port the delay is taken from hub descriptor. The optional settings: [Auto]; [Manual].Select [Manual] you can set value for the following sub-item: Device Power-up delay in seconds, the delay range in from 1 to 40 seconds, in one second increments.

3-8 Chipset Menu

► System Agent (SA) Configuration

Press [Enter] to make settings for the following sub-items: VT-d

32

Use this item to enable or disable VT-d capability. The optional settings are: [Enabled]; [Disabled]. Above 4GB MMIO BIOS assignment Use this item to enable or disable above 4GB memory Mapped IO BIOS assignment. This item is disabled automatically when Aperture Size is set as 2048 MB. The optional settings are: [Enabled]; [Disabled]. ► Memory Configuration Press [Enter] to view brief information for the working memory module.

► PCH-IO Configuration Press [Enter] to make settings for the following sub-items: HD Audio The optional settings are: [Disabled]; [Enabled]; [Auto]. Onboard Lan1 Controller/ Onboard Lan2 Controller Use this item to enable or disable LAN1/LAN2 device or controller. MPE Slot Use this item to enable or disable the PCI Express root port. The optional settings are: [Disabled]; [Enabled].

Speed The optional settings are: [Auto]; [Gen1]; [Gen2]; [Gen3].

MINIPCIE Slot Use this item to enable or disable the PCI Express root port. The optional settings are: [Disabled]; [Enabled].

Speed The optional settings are: [Auto]; [Gen1]; [Gen2]; [Gen3]. Onboard Lan BootROM Use this item to enable or disable Boot Option ROM for onboard network devices. Wake on LAN Use this item to enable or disable integrated LAN to wake the system.The Wake on LAN can not be disabled if ME is on at Sx state.

High Precision Timer

33

Use this item to enable or disable high precision timer. The optional settings are: [Disabled]; [Enabled].

3-9 Security Menu

Security menu allow users to change administrator password and user password settings. Administrator Password Press [Enter] to create new administrator password. Press again to confirm the new administrator password. User Password Press [Enter] to create new user password. Press again to confirm the new user password.

34

3-10 Boot Menu

Setup Prompt Timeout Use this item to set number of seconds to wait for setup activation key. Bootup Numlock State Use this item to select keyboard numlock state. The optional settings are: [On]; [Off]. Boot Option Priorities Fast Boot Use this item to enable or disable boot with initialization of a minimal set of devices required to launch active boot option. This item has no effect for BBS boot options. The optional settings are: [Enabled]; [Disabled].

35

When set as [Enabled], user can make settings in the following items that appear: SATA Support The optional settings are: [Last Boot HDD Only]; [All SATA Devices]. VGA Support The optional settings are: [Auto]; [EFI Driver]. *When set as [Auto], it will only install Legacy OpROM with Legacy OS and logo will not be shown during POST. EFI driver will still be installed with EFI OS. USB Support The optional settings are: [Disabled]; [Full Initial]; [Partial Initial]. [Disabled]: All USB devices will NOT be available until after OS boot; [Partial Initial]: USB mass storage and specific USB port/device will NOT be available before OS boot; [Full Initial]: All USB devices will NOT be available in OS and POST. PS2 Devices Support The optional settings are: [Disabled]; [Enabled]. The PS2 devices will be skipped if this is set as [Disabled]. Network Stack Driver Support The optional settings are: [Disabled]; [Enabled]. Network Stack Driver will be skipped if this is set as [Disabled]. Redirection Support Use this item to enable or disable Redirection Support. The optional settings are: [Disabled]; [Enabled].

36

3-11 Save & Exit Menu

Save Changes and Reset This item allows user to reset the system after saving the changes. Discard Changes and Reset This item allows user to reset the system without saving any changes. Restore Defaults Use this item to restore /load default values for all the setup options. Save as User Defaults Use this item to save the changes done so far as user defaults. Restore User Defaults Use this item to restore defaults to all the setup options.

37

Boot Override UEFI:xx/… Press this item to select the device as boot disk after save configuration and reset Launch EFI Shell from filesystem device Press this item to launch EFI Shell application (Shell.efi) from one of the available file system device.