scope of work - Bharat Petroleum
-
Upload
khangminh22 -
Category
Documents
-
view
4 -
download
0
Transcript of scope of work - Bharat Petroleum
SCOPE OF WORK
PROCUREMENT OF PRESSURE TRANSMITTER, DIFFERENTIAL PRESSURE TRANSMITTER &
TEMPERATURE TRANSMITTER
The specification of the materials are provided below and materials provided by the vendor should
be accordingly suitable for our use.
DIFFERENTIAL PRESSURE TRANSMITTER (0 to 2 Kg/cm2)
GENERAL
Function: Transmitter, indicating
TYPE: MICROPORCESSOR BASED SMART, HART
Case: Manufacturer standard
Mounting: YOKE -2 inch pipe mounting
Mounting accessories: Required
Mounting bracket: U bolt & nuts suitable for 2 inch pipe required
Electrical area classification: IEC zone-1 GR IIA/IIB, T3
Enclosure: weather proof IP-66 Class
Intrinsically safe: YES, Ex ia IIA/IIB, T3
Cable entry: 1/2" NPTF (2 nos)
Accuracy: "+/- 0.1% of calibrated span (including linearity hysteresis &
repeatability
Statutory Certification: CCOE certification required
SIL Rating: SIL 2
Calibration Report: Required.
TRANSMITTER
Output: 4-20 mA HART
Trans. Power supply: 24 V DC loop powered
Zero and span adjustments: Both these adjustments shall be accessible locally at the transmitter
as well as from the Hand Held Communicator (HHC). Both Zero &
Span adjustments shall be non-interactive. Local mechanism of
adjustment shall be clearly explained. This mechanism shall have
tamper proof features.
Rangeability (turndown ratio): 150:1
Response Time: 100 ms
Long Term Stability: +/- 0.2% of URL for 10 years or better
Temperature effect: Should be less than 0.005 % of range per Deg C
Ambient temperature
& Humidity: 5 Deg C to 65 Deg C & upto 95% RH non-condensing
Process temperature: 0 to 70 Deg C
Reverse polarity protection: To be provided
Local indicator: Integral LCD digital display should be provided with each
transmitter.
Local indicator should be 3- 1/2 digit or better. This unit shall have 2
line alpha numeric displays. It shall have the feature of rotation by
900 throughout 3600. Clearly mention the no. of digits of this
display.
Accuracy of display unit should be +/- 0.1% of input signal.
Electronics housing: It shall have the provision for rotation through 180 Deg C
Electronics: Electronics should be plug in cards type with high degree of
interchangeability among the transmitters of different ranges.
MEASURING UNIT
Service: Differential Pressure measurement of MS/HSD/SKO
Element: Diaphragm
Body material: Carbon steel
Element material: SS316
Process connection: 1/2" NPTF
Measuring Range: 0 to 2 Kg/cm2
Static pressure limit: 250 Kg/cm2
Static pressure effect on
Zero & span: Effect of static pressure should be clearly specified. Drift/error due
to static pressure in zero shall not be more than +/-0.1% of upper
range limit per 100 kg/cm2 change in static pressure. Span error
shall not be more than +/- 0.1% of upper range limit per 100 kg/cm2
change in static pressure. It should be possible to correct this error
through zero/span adjustment.
Over pressure limit: The design of the transmitter shall permit one side of the element to
be pressurized to maximum Design Static pressure of 250 Kg/cm2
with the other side vented to atmosphere, with no permanent
damage.
Vent / Drain Connection: To be provided on the side of the pressure chamber with 1/4 inch
NPT(F) thread & plug.
Warranty: 2 years warranty shall be provided from date of supply
PRESSURE TRANSMITTER (0 to 130 Kg/cm2)
GENERAL
Function: Transmitter, indicating
TYPE: MICROPORCESSOR BASED SMART, HART
Case: Manufacturer standard
Mounting: YOKE -2 inch pipe mounting
Mounting accessories: Required
Mounting bracket: U bolt & nuts suitable for 2 inch pipe required
Electrical area classification: IEC zone-1 GR IIA/IIB, T3
Enclosure: weather proof IP-66 Class
Intrinsically safe: YES, Ex ia IIA/IIB, T3
Cable entry: 1/2" NPTF (2 nos)
Accuracy: "+/- 0.075% of calibrated span (including linearity hysteresis &
repeatability
Statutory Certification: CCOE certification required
SIL Rating: SIL 2
Calibration Report: Required.
TRANSMITTER
Output: 4-20 mA HART
Trans. Power supply: 24 V DC loop powered
Zero and span adjustments: Both these adjustments shall be accessible locally at the transmitter
as well as from the Hand Held Communicator (HHC). Both Zero &
Span adjustments shall be non-interactive. Local mechanism of
adjustment shall be clearly explained. This mechanism shall have
tamper proof features.
Rangeability (turndown ratio): 150:1
Response Time: 100 ms
Long term Stability: +/- 0.2% of URL for 10 years or better
Temperature effect: Should be less than 0.005 % of range per Deg C
Ambient temperature
& Humidity: 5 Deg C to 65 Deg C & upto 95% RH non-condensing
Process temperature: 0 to 70 Deg C
Reverse polarity protection: To be provided
Local indicator: Integral LCD digital display should be provided with each
transmitter.
Local indicator should be 3-1/2 digit or better. This unit shall have 2
line alpha numeric displays. It shall have the feature of rotation by
900 throughout 3600. Clearly mention the no. of digits of this
display.
Accuracy of display unit should be +/- 0.1% of input signal.
Electronics housing: It shall have the provision for rotation through 180 Deg C
Electronics: Electronics should be plug in cards type with high degree of
interchangeability among the transmitters of different ranges.
MEASURING UNIT
Service: Pressure measurement of MS/HSD/SKO
Element: Diaphragm
Body material: Carbon steel
Element material: SS316
Process connection: 1/2" NPTF
Measuring Range: 0 to 130 Kg/cm2
Static pressure limit: 250 Kg/cm2
Static pressure effect on
Zero & span: Effect of static pressure should be clearly specified. Drift/error due
to static pressure in zero shall not be more than +/-0.1% of upper
range limit per 100 kg/cm2 change in static pressure. Span error
shall not be more than +/- 0.1% of upper range limit per 100 kg/cm2
change in static pressure. It should be possible to correct this error
through zero/span adjustment.
Over pressure limit: The design of the transmitter shall permit the element to
be pressurized to maximum Design Static pressure of 250 Kg/cm2
with no permanent damage.
Warranty: 2 years warranty shall be provided from date of supply
PRESSURE TRANSMITTER (0 to 20 Kg/cm2)
GENERAL
Function: Transmitter, indicating
TYPE: MICROPORCESSOR BASED SMART, HART
Case: Manufacturer standard
Mounting: YOKE -2 inch pipe mounting
Mounting accessories: Required
Mounting bracket: U bolt & nuts suitable for 2 inch pipe required
Electrical area classification: IEC zone-1 GR IIA/IIB, T3
Enclosure: weather proof IP-66 Class
Intrinsically safe: YES, Ex ia IIA/IIB, T3
Cable entry: 1/2" NPTF (2 nos)
Accuracy: "+/- 0.075% of calibrated span (including linearity hysteresis &
repeatability
Statutory Certification: CCOE certification required
SIL Rating: SIL 2
Calibration Report: Required.
TRANSMITTER
Output: 4-20 mA HART
Trans. Power supply: 24 V DC loop powered
Zero and span adjustments: Both these adjustments shall be accessible locally at the transmitter
as well as from the Hand Held Communicator (HHC). Both Zero &
Span adjustments shall be non-interactive. Local mechanism of
adjustment shall be clearly explained. This mechanism shall have
tamper proof features.
Rangeability (turndown ratio): 150:1
Response Time: 100 ms
Long term Stability: +/- 0.2% of URL for 10 years or better
Temperature effect: Should be less than 0.005 % of range per Deg C
Ambient temperature
& Humidity: 5 Deg C to 65 Deg C & upto 95% RH non-condensing
Process temperature: 0 to 70 Deg C
Reverse polarity protection: To be provided
Local indicator: Integral LCD digital display should be provided with each
transmitter.
Local indicator should be 3-1/2 digit or better. This unit shall have 2
line alpha numeric displays. It shall have the feature of rotation by
900 throughout 3600. Clearly mention the no. of digits of this
display.
Accuracy of display unit should be +/- 0.1% of input signal.
Electronics housing: It shall have the provision for rotation through 180 Deg C
Electronics: Electronics should be plug in cards type with high degree of
interchangeability among the transmitters of different ranges.
MEASURING UNIT
Service: Pressure measurement of MS/HSD/SKO
Element: Diaphragm
Body material: Carbon steel
Element material: SS316
Process connection: 1/2" NPTF
Measuring Range: 0 to 20 Kg/cm2
Static pressure limit: 250 Kg/cm2
Static pressure effect on
Zero & span: Effect of static pressure should be clearly specified. Drift/error due
to static pressure in zero shall not be more than +/-0.1% of upper
range limit per 100 kg/cm2 change in static pressure. Span error
shall not be more than +/- 0.1% of upper range limit per 100 kg/cm2
change in static pressure. It should be possible to correct this error
through zero/span adjustment.
Over pressure limit: The design of the transmitter shall permit the element to
be pressurized to maximum Design Static pressure of 250 Kg/cm2
with no permanent damage.
Warranty: 2 years warranty shall be provided from date of supply
PRESSURE TRANSMITTER (-1 to 4 Kg/cm2)
GENERAL
Function: Transmitter, indicating
TYPE: MICROPORCESSOR BASED SMART, HART
Case: Manufacturer standard
Mounting: YOKE -2 inch pipe mounting
Mounting accessories: Required
Mounting bracket: U bolt & nuts suitable for 2 inch pipe required
Electrical area classification: IEC zone-1 GR IIA/IIB, T3
Enclosure: weather proof IP-66 Class
Intrinsically safe: YES, Ex ia IIA/IIB, T3
Cable entry: 1/2" NPTF (2 nos)
Accuracy: "+/- 0.035% of calibrated span (including linearity hysteresis &
repeatability
Statutory Certification: CCOE certification required
SIL Rating: SIL 2
Calibration Report: Required.
TRANSMITTER
Output: 4-20 mA HART
Trans. Power supply: 24 V DC loop powered
Zero and span adjustments: Both these adjustments shall be accessible locally at the transmitter
as well as from the Hand Held Communicator (HHC). Both Zero &
Span adjustments shall be non-interactive. Local mechanism of
adjustment shall be clearly explained. This mechanism shall have
tamper proof features.
Rangeability (turndown ratio): 150:1
Response Time: 100 ms
Long term Stability: +/- 0.2% of URL for 10 years or better
Temperature effect: Should be less than 0.005 % of range per Deg C
Ambient temperature
& Humidity: 5 Deg C to 65 Deg C & upto 95% RH non-condensing
Process temperature: 0 to 70 Deg C
Reverse polarity protection: To be provided
Local indicator: Integral LCD digital display should be provided with each
transmitter.
Local indicator should be 3-1/2 digit or better. This unit shall have 2
line alpha numeric displays. It shall have the feature of rotation by
900 throughout 3600. Clearly mention the no. of digits of this
display.
Accuracy of display unit should be +/- 0.1% of input signal.
Electronics housing: It shall have the provision for rotation through 180 Deg C
Electronics: Electronics should be plug in cards type with high degree of
interchangeability among the transmitters of different ranges.
MEASURING UNIT
Service: Pressure measurement of MS/HSD/SKO
Element: Diaphragm
Body material: Carbon steel
Element material: SS316
Process connection: 1/2" NPTF
Measuring Range: -1 to 4 Kg/cm2
Static pressure limit: 250 Kg/cm2
Static pressure effect on
Zero & span: Effect of static pressure should be clearly specified. Drift/error due
to static pressure in zero shall not be more than +/-0.1% of upper
range limit per 100 kg/cm2 change in static pressure. Span error
shall not be more than +/- 0.1% of upper range limit per 100 kg/cm2
change in static pressure. It should be possible to correct this error
through zero/span adjustment.
Over pressure limit: The design of the transmitter shall permit the element to
be pressurized to maximum Design Static pressure of 250 Kg/cm2
with no permanent damage.
Warranty: 2 years warranty shall be provided from date of supply
TEMPERATURE TRANSMITTER (0 to 100 Deg C)
GENERAL
Function: Transmitter, indicating
TYPE: MICROPORCESSOR BASED SMART, HART
Case: Manufacturer standard
Mounting: YOKE – 2 inch pipe mounting
Mounting accessories: Required
Mounting bracket: U bolt & nuts suitable for 2" pipe required
Electrical area classification: IEC zone-1 GR IIA/IIB, T3
Enclosure: weather proof IP-66 Class
Intrinsically safe: YES, Ex ia IIA/IIB, T3
Cable entry: 1/2" NPTF (2 nos)
Accuracy: "+/- 0.2 % of calibrated span (including linearity hysteresis &
repeatability
Statutory Certification: CCOE certification required
SIL Rating: SIL 2
Calibration Report: Required.
TRANSMITTER
Output: 4-20 mA HART
Trans. Power supply: 24 V DC loop powered
Zero and span adjustments: Both these adjustments shall be accessible locally at the transmitter
as well as from the Hand Held Communicator (HHC). Both Zero &
Span adjustments shall be non-interactive. Local mechanism of
adjustment shall be clearly explained. This mechanism shall have
tamper proof features.
Long term Stability: +/- 0.2% of URL for 10 years
Temperature effect: Should be less than 0.005 % of range per Deg C
Ambient temperature
& Humidity: 5 Deg C to 65 Deg C & upto 95% RH non-condensing
Process temperature: 0 to 70 Deg C
Reverse polarity protection: To be provided
Local indicator: Integral LCD digital display should be provided with each
transmitter.
Local indicator should be 3-1/2 digit or better. This unit shall have 2
line alpha numeric displays. It shall have the feature of rotation by
900 throughout 3600. Clearly mention the no. of digits of this
display.
Accuracy of display unit should be +/- 0.1% of input signal.
Electronics housing: It shall have the provision for rotation through 180 Deg C
Electronics: Electronics should be plug in cards type with high degree of
interchangeability among the transmitters of different ranges.
MEASURING UNIT
Service: Temperature measurement of MS/HSD/SKO
Type: Pt-100, Simplex, 3 wire RTD
Body material: Carbon steel
Element material: SS316
Measuring Range: 0 to 100 Deg C
Warranty: 2 years warranty shall be provided from date of supply
The materials should be delivered to given addresss according to the list
given below:
ADDRESS 1:
MUMBAI REFINERY,
BHARAT PETROLEUM CORPORATION LIMITED
MAHUL GAON, CHEMBUR
MUMBAI,400074
ITEM QTY UNT
Pressure Transmitter -1 to 4 Kg/cm2 for Mumbai 2 No.
Pressure Transmitter 0 to 20 Kg/cm2 for Mumbai 8 No.
Pressure Transmitter 0 to 130 Kg/cm2 for Mumbai 5 No.
Differential Pressure Transmitter 0 to 2 Kg/cm2 for Mumbai 4 No.
Temperature Transmitter 0 to 100 deg C for Mumbai 6 No.
ADDRESS 2:
WASHALA PUMPING STATION – MMBPL BHARAT PETROLEUM CORP. LTD VILLAGE-WASHALA, 7 KM from KASARA RAILWAY STATION TALUKA – SHAHPUR DISTRICT – THANE, MAHARASTRA – 421604 MOBILE: 9823060209
ITEM QTY UNT
Pressure Transmitter 0 to 20 Kg/cm2 for Washala 5 No.
Pressure Transmitter 0 to 130 Kg/cm2 for Washala & SV-1 to 14 28 No.
Differential Pressure Transmitter 0 to 2 Kg/cm2 for Washala 2 No.
ADDRESS 3:
MOBILE: 9422271487
ITEM QTY UNT
Pressure Transmitter -1 to 4 Kg/cm2 for Manmad 2 No.
Pressure Transmitter 0 to 20 Kg/cm2 for Manmad & Sanghvi 13 No.
Pressure Transmitter 0 to 130 Kg/cm2 for Manmad & Sanghvi 6 No.
MANMAD TERMINAL - MMBPL BHARAT PETROLEUM CORP. LTD MANMAD – NANDGAON ROAD PANEWADI, MANMAD MAHARASTRA -- 423104
ADDRESS 4:
MANGALYA TERMINAL MMBPL CONTROL ROOM BHARAT PETROLEUM CORP.LTD MANGALYA – SANVER ROAD INDORE- 453771 MOBILE: 9425065623
ITEM QTY UNT
Pressure Transmitter 0 to 20 Kg/cm2 for Manglya & Gujri 7 No.
Pressure Transmitter 0 to 130 Kg/cm2 for Manglya & Gujri 6 No.
ADDRESS 5:
IPS KOTA – MMBPL BHARAT PETROLEUM CORP. LTD VILLAGE- BRIJESHPURA TAHSIL – TATHED DISTRICT – KOTA RAJASTHAN – 325201 MOBILE: 9928035386
ITEM QTY UNT
Pressure Transmitter 0 to 20 Kg/cm2 for Kota 4 No.
Pressure Transmitter 0 to 130 Kg/cm2 for Kota, Sherpur, Malarna, Bharatpur, Karwadi 16 No.
ADDRESS 6: IPS MATHURA – MMBPL BHARAT PETROLEUM CORP. LTD ROAD NO 26, UPSIDC IND AREA, OPPOSITE IOCL REFINERY, MATHURA – 281005, MOBILE: 9412777828
ADDRESS 7:
PIYALA INSTALLATION – MMBPL BHARAT PETROLEUM CORP. LTDVILLAGE – PIYALA, POST – ASAOTI TEHSIL – BALLABGARH , DIST - FARIDABAD HARYANA – 121102 MOBILE : 9999102660
ITEM QTY UNT
Pressure Transmitter 0 to 20 Kg/cm2 for Piyala 4 No.
Pressure Transmitter 0 to 130 Kg/cm2 for Piyala 4 No.
ADDRESS 8:
BIJWASAN INSTALLATION – MMBPL BHARAT PETROLEUM CORP. LTD POST – BIJWASAN NEW DELHI – 110061,MOBILE: 9910072573
ITEM QTY UNT
Pressure Transmitter 0 to 130 Kg/cm2 for Bijwasan 1 No.
ITEM QTY UNT
Pressure Transmitter 0 to 20 Kg/cm2 for Mathura 2 No.
Pressure Transmitter 0 to 130 Kg/cm2 for Mathura 2 No.
Differential Pressure Transmitter 0 to 2 Kg/cm2 for Mathura 2 No.
ADDRESS 9:
ITEM QTY UNT
Pressure Transmitter 0 to 20 Kg/cm2 for Bina 2 No.
Pressure Transmitter 0 to 130 Kg/cm2 for Bina & Guna 3 No.
Temperature Transmitter 0 to 100 deg C for Bina 4 No.
BORL REFINERY, GATE NO – 3 BINA DESPATCH TERMINAL BHARAT PETROLEUM CORP.LTD BINA – MUNGAWALI ROAD VILLAGE – DEHRI, TEHSIL – BINA, DISTT.- SAGAR(M.P.) - 470113, MOBILE – 09575304063