How to change max cell Tx power

HUAWEI TECHNOLOGIES CO., LTD. Huawei Confidential

Security Level:

Slide title :40-47pt Slide subtitle :26-30pt

Color::white Corporate Font :

FrutigerNext LT MediumFont to be used by customers

and partners :

Arial

www.huawei.com

How to change max cell Tx power


Top right corner for field-mark, customer or partner logotypes.

---------------- The following nine groups of colors are an example of how our design colors can be used, please take note that you should only use one design color group per slide. For specific usage details, refer to the “Typesetting Standard”.

Incident Description• Due to power congestion issue at xxx area, my

team leader requested me to increase the max tx power to 478 & cpich power to 380 for these cells [2012-03-06, 15.20].

• As per the request script been prepared for RNC & nodeB Due to last minute & late hours preparation,

typo error occurred where node B set 460 while RNC side set as 478 [2012-03-06, 21.00].

Scrip run by RIC team [2012-03-08 03.30] & unblock status of the cells never been checked

RIC team also never check the 1st hour of the stats for the particular cells.

• On morning BO team only check RIC log performed which was successfully & not the stats [2012-03-08 09.00].

• The site didn’t unblocked after script completed by RIC & only BO team realize after the customer complain [2012-03-08 11:25].




Recover process

• We noticed Max tx power for RNC & node B scripted wrongly from the script that sent to RIC team [2012-03-08 11:50].

• We tried to change the node B max tx power setting to 478 as we plan but failed.

• Noticed the configured license for power set as 46dBm & we increased the power license to 47.8dBm.

• We manage to increase the node B power to 478 & unblock the cells

• All the cells start picking up the traffic [2012-03-08 13:30].




Lesson learned

• We learned the lesson from the mistakes as below Try to avoid last minute & late hours

preparation since this can invent more human error or typo error.

Double/triple check the script before implement RIC team must check the cell’s administrative

state as Unblocked to confirm the cell is up. RIC team must check the early hours of the

performance/traffic of the cells BO team must double confirm the

performance/traffic of the cells once they clock in to office.




Max cell Tx power change Process1. Define available power license & enable

needed power license (Without right license in node B, the cell can’t changed to higher power) Example – For 46dBm license (423/3000) need to

be enable while for 47.8dBm license (0/3000) need to be enable

2. RNC side: block the cell and change maxTxPower

3. Node B side: change maxpwr of LOCELL, must same as RNC side (if the value is not same the site cannot be unblocked)

4. RNC side: unblock the cell5. RNC side & node B side: double confirm the

status of cell is activated6. Monitor the real time stats to double confirm

the cell is up & running.




Check the 60W license availability• There are two kinds of power license in VHA

project 40W (46dBm) 60W (47.8dBm)

• The availability of power license can be found in M2000 “License” – “NE License management” - “Node B license management”




Distribute license to Node B (1/2)• The 60W license need to be distributed to Node

B before change cell max Tx power1. Step 1: Select the Node B2. Step 2: Change the number of license need to be

distributed (1 for each PA)




Distribute license to Node B (2/2)• Step 3: Distribute the license

Please double check the license activated status is True




Script to change cell max Tx power• RNC side: block the cell and change maxTxPower

BLK UCELL:CellId=xxxxx,Priority=HIGH; MOD UCELL: CellId=xxxxx,MaxTxPower=478;

• Node B side: change maxpwr of LOCELL, must same as RNC side MOD LOCELL:

LOCELL=1,SECT=LOCAL_SECTOR,MXPWR=478;• RNC side: unblock the cell

UBL UCELL: CellID=xxxxx;• RNC side & node B side : double confirm the

status of cell is activated DSP UCELL:CellID=xxxxx;




Double confirm the cell is activated1. RNC side & node B side: double confirm the

status of cell is activated In MML command, command “LST UCELL” will give

“cell administrative state” as Unblocked to confirm the cell is up.

2. Monitor the real time stats to double confirm the cell is up & running.

Thank youwww.huawei.com

How to change max cell Tx power

Documents

Transcript of How to change max cell Tx power