DCM-M1 - SERVICE MANUAL
198
MICROFILM SERVICE MANUAL Ver 1.3 2000. 08 With SUPPLEMENT-1 (9-927-635-81) With SUPPLEMENT-2 (9-927-635-82) With SUPPLEMENT-3 (9-927-635-83) MINIDISC AV RECORDER US Model Canadian Model E Model SPECIFICATIONS DCM-M1 Model Name Using Similar Mechanism NEW Mechanism Type CT-DCMM1-164 Model Name Using Similar Mechanism NEW Mechanism Type MT-DCMM1-163 MD Section Lens Section – Continued on next page –
-
Upload
khangminh22 -
Category
Documents
-
view
2 -
download
0
Transcript of DCM-M1 - SERVICE MANUAL
MICROFILM
SERVICE MANUALVer 1.3 2000. 08With SUPPLEMENT-1(9-927-635-81)With SUPPLEMENT-2(9-927-635-82)With SUPPLEMENT-3(9-927-635-83)
MINIDISC AV RECORDER
US ModelCanadian Model
E Model
SPECIFICATIONS
DCM-M1
Model Name Using Similar Mechanism NEW
Mechanism Type CT-DCMM1-164
Model Name Using Similar Mechanism NEW
Mechanism Type MT-DCMM1-163MDSection
LensSection
– Continued on next page –
– 2 –
1. Check the area of your repair for unsoldered or poorly-sol-dered connections. Check the entire board surface for soldersplashes and bridges.
2. Check the interboard wiring to ensure that no wires are“pinched” or contact high-wattage resistors.
3. Look for unauthorized replacement parts, particularly transis-tors, that were installed during a previous repair. Point themout to the customer and recommend their replacement.
SAFETY CHECK-OUT
After correcting the original service problem, perform the followingsafety checks before releasing the set to the customer.
4. Look for parts which, though functioning, show obvious signsof deterioration. Point them out to the customer and recom-mend their replacement.
5. Check the B+ voltage to see it is at the values specified.
6. Flexible Circuit Board Repairing
• Keep the temperature of the soldering iron around 270 ˚Cduring repairing.
• Do not touch the soldering iron on the same conductor ofthe circuit board (within 3 times).
• Be careful not to apply force on the conductor when sol-dering or unsoldering.
SAFETY-RELATED COMPONENT WARNING!!
COMPONENTS IDENTIFIED BY MARK 0 OR DOTTEDLINE WITH MARK 0 ON THE SCHEMATIC DIAGRAMSAND IN THE PARTS LIST ARE CRITICAL TO SAFEOPERATION. REPLACE THESE COMPONENTS WITHSONY PARTS WHOSE PART NUMBERS APPEAR ASSHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUB-LISHED BY SONY.
ATTENTION AU COMPOSANT AYANT RAPPORTÀ LA SÉCURITÉ!
LES COMPOSANTS IDENTIFIÉS PAR UNE MARQUE 0SUR LES DIAGRAMMES SCHÉMATIQUES ET LA LISTEDES PIÈCES SONT CRITIQUES POUR LA SÉCURITÉDE FONCTIONNEMENT. NE REMPLACER CES COM-POSANTS QUE PAR DES PIÈCES SONY DONT LESNUMÉROS SONT DONNÉS DANS CE MANUEL OUDANS LES SUPPLÉMENTS PUBLIÉS PAR SONY.
– 3 –
SERVICE NOTE ................................................ 4
1. GENERALGetting Started ...................................................................... 1-1Recording – Basics ............................................................... 1-5Playback – Basics ................................................................. 1-7Advanced Recording Operations .......................................... 1-8Advanced Playback Operations ............................................ 1-11Editing ................................................................................... 1-14Drawing/Effect ....................................................................... 1-19Customing Your Camcorder .................................................. 1-21Using with Other Equipment ................................................. 1-23Additional Information ............................................................ 1-26Quick Reference .................................................................... 1-28
2. DISASSEMBLY
2-1. Main Control Switch Unit ............................................. 2-32-2. Cabinet (R) Section ..................................................... 2-32-3. Zoom Switch Unit ........................................................ 2-32-4. Power Board ................................................................ 2-42-5. Ether Board ................................................................. 2-42-6. Jack Board ................................................................... 2-42-7. Remote Terminal Unit .................................................. 2-52-8. Battery Case Assembly ............................................... 2-52-9. Microphone Block ........................................................ 2-52-10. Main Board .................................................................. 2-62-11. Lens Block (CT-DCMM1-164) ..................................... 2-62-12. Hinge Cover ................................................................. 2-62-13. LCD Block .................................................................... 2-72-14. LCD Cabinet Assembly (U) ......................................... 2-72-15. LCD Board ................................................................... 2-72-16. Fluorescent Tube ......................................................... 2-82-17. Touch Panel, LCD Module (LCD4301) ....................... 2-82-18. EVF Block .................................................................... 2-82-19. VF Board ..................................................................... 2-92-20. VF Lens Assembly ...................................................... 2-92-21. BL Board ...................................................................... 2-92-22. Upper Panel Assembly ................................................ 2-92-23. Mechanism Deck (MT-DCMM1-163) ........................... 2-102-24. CLV Board ................................................................... 2-102-25. Stepper Block Assembly (M5811) ............................... 2-112-26. Holder Assembly ......................................................... 2-112-27. Service Position ........................................................... 2-122-28. Circuit Boards Location ............................................... 2-142-29. Flexible Boards Location ............................................. 2-16
3. BLOCK DIAGRAMS
3-1. Overall Block Diagram ................................................. 3-13-2. Camera Signal Process Block Diagram ...................... 3-33-3. Camera Control Block Diagram .................................. 3-53-4. A/V Data Control, Video Out Block Diagram .............. 3-73-5. MPEG Encode Block Diagram .................................... 3-93-6. MD Signal Process Block Diagram ............................. 3-113-7. MD Servo Block Diagram ............................................ 3-133-8. System Control Block Diagram ................................... 3-153-9. Audio Block Diagram ................................................... 3-173-10. LCD Block Diagram ..................................................... 3-193-11. EVF Block Diagram ..................................................... 3-213-12. Mode Control Block Diagram ...................................... 3-233-13. Ether Interface Block Diagram .................................... 3-253-14. Power 1 Block Diagram ............................................... 3-273-15. Power 2 Block Diagram ............................................... 3-293-16. Power 3 Block Diagram ............................................... 3-31
4. PRINTED WIRING BOARDS ANDSCHEMATIC DIAGRAMS
4-1. Frame Schematic Diagram.......................................... 4-54-2. Printed Wiring Boards and Schematic Diagrams ....... 4-9
VC-216 Printed Wiring Board ...................................... 4-9VC-216 (LENS MOTOR DRIVE, CCD IMAGER)Schematic Diagram ..................................................... 4-13VC-216 (CAMERA SIGNAL PROCESS)Schematic Diagram ..................................................... 4-17MAIN Printed Wiring Board ......................................... 4-21MAIN (AUDIO/VIDEO DATA CONTROL)Schematic Diagram ..................................................... 4-29MAIN (MPEG ENCODER/DECODER)Schematic Diagram ..................................................... 4-33MAIN (RF AMP/DRIVE) Schematic Diagram ............. 4-39MAIN (DIGITAL SIGNAL PROCESSOR)Schematic Diagram ..................................................... 4-43MAIN (SYSTEM CONTROL) Schematic Diagram ..... 4-48MAIN (VIDEO) Schematic Diagram ............................ 4-53MAIN (AUDIO) Schematic Diagram ............................ 4-56MAIN (SWITCHING REGULATOR)Schematic Diagram ..................................................... 4-59MAIN CONTROL SWITCH UNIT, ZOOM SWITCHUNIT Schematic Diagram ........................................... 4-62UPPER CONTROL SW SUB ASSY,REMOCON RAY-CATCHER BLOCK UNIT,LCD DETECTION SW FLEXIBLE BoardSchematic Diagram ..................................................... 4-65CLV Printed Wiring Board ........................................... 4-68CLV Schematic Diagram ............................................. 4-75REC Printed Wiring Board andSchematic Diagram ..................................................... 4-79VF Printed Wiring Board ............................................. 4-83VF Schematic Diagram ............................................... 4-87BL Printed Wiring Board ............................................. 4-93BL Schematic Diagram ............................................... 4-97LCD Printed Wiring Board ........................................... 4-101LCD Schematic Diagram ............................................. 4-106ETHER Printed Wiring Board ...................................... 4-109ETHER Schematic Diagram........................................ 4-116JACK Schematic Diagram ........................................... 4-119JACK Printed Wiring Board ......................................... 4-121POWER Printed Wiring Board .................................... 4-125POWER Schematic Diagram ...................................... 4-130
4-3. Waveforms ................................................................... 4-133
5. EXPLODED VIEWS
5-1. Main Section ................................................................ 5-15-2. Cabinet (R) Section ..................................................... 5-25-3. Microphone Block Section .......................................... 5-35-4. Cabinet (L) Section ..................................................... 5-45-5. LCD Block Section ...................................................... 5-55-6. EVF Block Section ....................................................... 5-65-7. Lens Block Section (CT-DCMM1-164) ........................ 5-75-8. Mechanism Deck Section-1
(MT-DCMM1-163) ........................................................ 5-85-9. Mechanism Deck Section-2
(MT-DCMM1-163) ........................................................ 5-9
6. ELECTRICAL PARTS LIST ............................. 6-1
TABLE OF CONTENTS
Section Title Page Section Title Page
* The color reproduction frame is shown after the pageof ELECTRICAL PARTS LIST.
– 4 –
SERVICE NOTE
• NOTE FOR REPAIR
Make sure that the flat cable and flexible board are not cracked ofbent at the terminal.Do not insert the cable insufficiently nor crookedly.
When remove a connector, don’t pull at wire of connector.Be in danger of the snapping of a wire.
Cut and remove the part of gilt which comes off at the point.(Take care that there are some pieces of gilt left inside)
When installing a connector, don’t press down at wire of connector.Be in danger of the snapping of a wire.
• When repairing this device with the power on, if you removethe MAIN board or open the upper panel assy, this device stopsworking.In this case, you can work without the device stopping by fas-tening the hook of the open/close detect switch (S8003) on theMAIN Board with tape.
S8003
1-1
SECTION 1GENERAL
This section is extracted from in-struction manual. (3-866-152-11)
DCM-M1
1-2
1-3
1-4
1-5
1-6
1-7
1-8
1-9
1-10
1-11
1-12
1-13
1-14
1-15
1-16
1-17
1-18
1-19
1-20
1-21
1-22
1-23
1-24
1-25
1-26
1-27
1-28
1-29
1-301-30 E
2-1
SECTION 2DISASSEMBLY
• This set can be disassembled in the order shown below.
DCM-M1
Holder Assembly(Page 2-11)
Main Control Switch Unit(Page 2-3)
DCM-M1
Cabinet (R) Section(Page 2-3)
Zoom Switch Unit(Page 2-3)
Microphone Unit(Page 2-5)
EVF Block(Page 2-8)
Upper Panel Assembly(Page 2-9)
VF Board(Page 2-9)
BL Board(Page 2-9)
VF Lens Assembly(Page 2-9)
CLV Board(Page 2-10)
Ether Board(Page 2-4)
Power Board(Page 2-4)
Jack Board(Page 2-4)
Main Board(Page 2-6)
Remote Terminal Unit(Page 2-5)
Lens Block (CT-DCMM1-164)(Page 2-6)
Mechanism Deck (MT-DCMM1-163)(Page 2-10)
Stepper Block Assembly (M5811)(Page 2-11)
Hinge Cover(Page 2-6)
LCD Block(Page 2-7)
LCD Cabinet Assembly (U)(Page 2-7)
Touch Panel, LCD Module (LCD4301)(Page 2-8)
Fluorescent Tube(Page 2-8)
LCD Board(Page 2-7)
Battery Case Assembly(Page 2-5)
2-2
S1 S2 S3 S4
S5 S6 S7 S8
S9 S10 S11 S12
S13 S14 S15 S16
22
4
2.5
5 3
5
3
2
4.5 4 4
4.53.5
1.6 1.3
PAPER BOX FOR SCREW
We suggest to make a photo copy of this page before removing the set,put cellophane tape (adhesive tape) in each dotted-line frame for each screw.You can replace these screws without any mistakes after this preparation.(If you use OHP sheet or something similar, you can use it repeatedly.)
unit: mm
2-3
Note: Follow the disassembly procedure in the numerical order given.
2-1. MAIN CONTROL SWITCH UNIT 2-3. ZOOM SWITCH UNIT3 Two screws (S1)
(M1.7 × 3)5 Two screws (S3)
(M1.7 × 4)
4 Screw (S2)(M1.7 × 4.5)
8 Flexible board(zoom switch unit)
7 Translation flexible board2 Screw (S1)
(M1.7 × 3)
1 Open the LCD panel.
6 Main control switch unit
2-2. CABINET (R) SECTION
3 Screw (S5)(M2.0 × 4.5)
8 Translationflexible (jack)board (CN3002)
4 Screw (S1)(M1.7 × 3)
7 Cabinet (R) section
9 Flexible board(ether board)(CN8007)
0 Flexible board (power board)(CN9101)
5 Screw (S1)(M1.7 × 3)
2 Bracket(shoe)
1 Two screws (S4)(K2 × 4)
6 Screw (S3)(M1.7 × 4)
2 Zoom switch unit
1 Screw (S6)(M1.7)
4.5
3.5
3
4
4.5
4
S1 S4
S2 S5
S3 S6
2-4
2-6. JACK BOARD2-4. POWER BOARD
2-5. ETHER BOARD
3 Earth lug
1 Connector
4 Two screws (S8)(M1.7)
5 POWER board
2 Two screws (S7)(M1.7 × 5)
1 Screw (S7)(M1.7 × 5)
3 Insulatingsheet
4 Screw (S7)(M1.7 × 5)
2 Bracket(ether board)5 Two earth lugs
6 ETHER board
3 Flexible board(remote terminal unit)(CN8004)
2 Translation flexible (jack) board(CN3003)
4 Two screws (S8)(M1.7)
5 Remove the JACK boardin the direction of the arrow.
1 Open the jack cover.
5
3
S7
S8
2-5
2-7. REMOTE TERMINAL UNIT 2-9. MICROPHONE BLOCK
2-8. BATTERY CASE ASSEMBLY
ETHER
1 Screw (S8)(M1.7)
2 Remove the remoteterminal unit in thedirection of the arrow.
1 Two screws (S3)(M1.7 × 4)
2 Screw (S3)(M1.7 × 4)
4 Battery case assembly
3 Screw (S3)(M1.7 × 4)
1 Connector(CN3001)
5 Microphone block
2 Flexible board(remocon ray-catcher block unit)(CN8003)
4 Lug
3 Screw (S8)(M1.7)
4
3
S3
S8
2-6
2-10. MAIN BOARD 2-12. HINGE COVER
2-11. LENS BLOCK(CT-DCMM1-164)
0 Three screws (S9)(M1.4 × 2)
4 Flexible board(OP block)(CN5011)
9 Screw (S8)(M1.7)
8 Screw (S7)(M1.7 × 5)
5 Flexible board(CLV board)(CN5002)
6 Connector(yellow)(CN4312)
qs Connector(gray)(CN4313)
qa MAIN board
3 VF flexible board(CN4511)
2 Flexible board(upper control switch unit)(CN8002)
1 Flexible board(VC-216 board)(CN8101)
7 LCD detection sw flexible board(CN8006)
1 Acostic isolation (S)material
2 Screw (S1)(M1.7 × 3)
3Lens block (CT-DCMM1-164)
6 Two screws (S10)(M1.7 × 2.5)
7 Blind plateassembly
8 Screw (S1)(M1.7 × 3)
2 Two screws (S1)(M1.7 × 3)
1 Open the LCD paneland turn it 90°.
3 Two claws
5 Hinge cover (front)
9 Hinge cover (rear)
4 Claw
3 2
2.55
3
S8
S7 S10
S9S1
2-7
2-13. LCD BLOCK 2-15. LCD BOARD
2-14. LCD CABINET ASSEMBLY (U)
3 Screw (S11)(PS2 × 5)
LCD panel Hinge assembly
1 Set the LCD panel andhinge assembly to a stateof the figure.
6 Remove the LCD blockin the direction of the arrow.
2 Screw (S11)(PS2 × 5)
4 Boss
5 Boss
2 Two screws (S1)(M1.7 × 3)
A
B
3 Remove the LCD cabinet assembly (U)in the direction of the arrows A-B.
1 Turn the hinge assembly.
1 Screw (S10)(M1.7 × 2.5)
9 Screw (S8)(M1.7)
qa LCD board
8 Flexible board(fluorescent tube)(CN4307)
7 Flexible board(touch panel)(CN4301)
6 Flexible board(LCD)(CN4306)
0 claw
5 Two connectors(CN4302, 4303)
3 Claw
4 LCD frame2 Two claws
3
3
2.5
5
S10
S8
S1 S11
2-8
2-16. FLUORESCENT TUBE 2-18. EVF BLOCK
2-17. TOUCH PANEL, LCD MODULE (LCD4301)
1 Claw
2 Fluorescent tube
6 Touch panel,LCD module (LCD4301)
5 Claw
3 Claw
2 Claw
1 Two screws (S10)(M1.7 × 2.5)
4 Hinge assembly
1 Screw (S3)(M1.7 × 4) 2 EVF block
2.5
4
S3
S10
2-9
2-19. VF BOARD 2-21. BL BOARD
2-20. VF LENS ASSEMBLY
2-22. UPPER PANEL ASSEMBLY
5 Claw
1 VF/LCD Flexible board(CN4601)
3 Claw
6 Two claws
2 Two claws
7 VF board
4 Claw
2 Two screws (S7)(M1.7 × 5)
1 Two screws (S7)(M1.7 × 5)
Visibility adjustment arm
Shaft
4 VF lens assembly
Note : When installing VF lens assembly,move the visibility adjustment knob in the direction of the arrow and connect shaft of VF lens assemblywith visibility adjustment arm.
Visibility adjustment knob
3 EVF cabinet (upper)
1 Flexible board(LCX024AK-5)(CN4702)
4 BL board
2 Claw
3 Two claws
5 2
S7 S12
5 Upper panel assembly
1 Set on eject position.
2 Screw (S12)(M1.4 × 2)
4 Two screws (S12)(M1.4 × 2)3 Screw (S12)
(M1.4 × 2)
2-10
2-23. MECHANISM DECK(MT-DCMM1-163)
2-24. CLV BOARD
3 Two screws (S13)(damper)
OK NG NG
Note : When installing damper (MD),put it together in the figure.
4 Damper (MD)
7 Claw1 Rotate the worm gear in the direction
of the arrow A and move the torsion spring (limitter) in the direction of the arrow B.
Worm gearA
B
Torsion spring (limitter)
8 Claw
9 Hold the part maked A in thefigure trying not to touch eitherover write head or OP.Pulling the mechanism deck(MT-DCMM1-163) toward you,pull out it to the disc slot side.
6 Damper (MD)
5 Two dampers (MD)
2 Two screws (S13)(damper)
A
4 Two screws (S14)(M1.4)
2 Motor flexible board(CN5801)
5 CLV board
1 Flexible board(CN5902)
3 Remove the solders of the spindlemotor flexible board.
1.6
4
S13
S14
2-11
2-25. STEPPER BLOCK ASSEMBLY (M5811)
2-26. HOLDER ASSEMBLY
3 Screw (S15)(M1.4)
5 Stepper block assembly(M5811)
2 Motor flexible board
1 Remove solders of motor flexible board.
4 Claw
1.3
2
S15
S16
6 Shaft
Lever (rack)
Note : When installing holder assembly, connect lever (cam) with lever (rack). 7 Holder assembly
Holder assembly Flexible board(over write head)
Note : When connecting flexible board (over write head), put it togetherin the figure.
4 Holder guide
5 Shaft
3 Screw (S16)(M1.4)
1 Flexible board (CLV board)(CN5902)
2 Flexible board(over write head)(CN5901)
2-12
2-27. SERVICE POSITIONPreparation: Refer to previous section “DISASSEMBLY”, and connect as shown in the figure after each part has been removed.
MAIN BOARD, CLV BOARD
LCD BOARD VF BOARD
Battry case assembly
Lens block
AC adaptor(AC-VQ800)
AC in
Zoom switch unit
Main control switch unit
MAIN board
CLV board
Cabinet (L) blockPOWER boardLCD block
Note : Put an insulating sheetbetween MAIN board andPOWER board.
Stand
LCD blockLCD board
AC adaptor(AC-VQ800)
AC in
Stand
POWER board
MAIN board
EVF block
VF board
AC adaptor(AC-VQ800)
AC in
Main control switch unit
Stand
2-13
MEMO
2-14
2-28. CIRCUIT BOARDS LOCATION
POWER board(DC/DC CONVERTER)
BL board(EVF BACK LIGHT) VF board
(EVF)
MAIN boardAUDIO/VIDEO DATA CONTROL, MPEG ENCODER/DECODER,RF AMP/DRIVE, DIGITAL SIGNAL PROCESSOR,SYSTEM CONTROL, VIDEO, AUDIO, SWITCHING REGULATOR
2-15
JACK board(AV IN/OUT)
ETHER board(ETHER INTERFACE)
LCD board(LCD)
VC-216 boardLENS MOTOR DRIVE,CCD IMAGER,CAMERA SIGNAL PROCESS
REC boardOVER WRITEHEAD DRIVE
CLV board(MD MOTOR DRIVE)
2-16
2-29. FLEXIBLE BOARDS LOCATION
Remote terminal unit
Remocon ray-catcherblock unit
Fluorescent tube
1 Translation flexible board
Upper control switch unit
3 VF/LCD flexible board
4 LCD detection swflexible board
Touch panel
LCD module (LCD4301)
Zoom switch unit
LCD module (LCD4701)
Lens device
2-17
OP block
Spindle motor(M5821)
2 Translation flexible(jack) board
5 Motor flexible board
VF flexible board
Over write head (HR5901)
10
10
3815
5
22
5
11
93
5 65
263
3
4
10
1 Translation flexible board 2 Translation flexible (jack) board 3 VF/LCD flexible board
4 LCD detection sw flexible board 5 Motor flexible board
2-17 E
unit: mm
DCM-M1
ZOOM LENSZOOM LENS UNIT
IRIS METER
M
M903ZOOM MOTOR
M902FOCUS MOTOR
CCDIMAGER
IC001CCD OUT
EEP ROM
IC103
ZOOM MOTORDRIVE
FOCUS MOTORDRIVE
IC202
S/H,AGC,A/D CONVERTER
IC102 D0-D9 Y0-Y7
C0-C3MEC0-MEC7
MVP
0-M
VP7
ENDT
0-EN
DT7
SYS MVP0-SYS MVP7
MPEG2ENCODER
IC8601
64M SDRAM
IC8602
16M EDO DRAMIC8702 IC8703
64M SDRAM
IC8002 IC8003
1M EEPROMIC8004
64M FLASHIC8005
RESETIC8009
MPEG2VIDEO
PROCESSOR
IC8701
PARA
LLEL
BUS
SERIAL BUS
SERI
AL B
US
SERIAL BUS
SERIAL BUS
SERIAL BUS
SERI
AL B
USSERIAL BUS
SERIAL BUS
SERIAL BUS
SERIAL BUS
CAMERAY/C
PROCESS
IRIS/FOCUS/ZOOM
CONTROL
IC105MD2 DIGITAL
SIGNALPROCESSOR
IC5403
A/D CONVERTER
IC5102
MD1 DIGITALSIGNAL
PROCESSOR
DIGITALSERVOSIGNAL
PROCESSOR
IC5301MDTI
DDI V IN
RFI
D0-D7
DDO HN-H/L,HP-H/L OUT A/B
RF AMPFOCUS/TRACKING
ERROR AMP
IC5002RFO
MNT0
DADT
I,JRF
HEAD UP/DOWNMOTOR DRIVE
IC5601
PHASE CONTROL
IC5804 IC5805 IC5806 IC5808
TEMPERATURESENSOR
IC5406
CY
C
Y
C
Y
C
Y
VIDEOLINE-L
LINE-R
HP-R
HP-L
SP+
LINE OUT L/RHP OUT L/R
L/R OUT1
L/R IN1
LINE IN L/R
MIC IN L/R
MIC R
MIC L
MIC R
MIC L
LINE R
LINE L
L/R IN2
SDTOACDO
ACDO
ACDI
SDTIACDI
DIDT
L/R OUT2
HP OUT L/R
C
Y
B-YR-Y
YB-YR-Y
YB-YR-Y
GBR
GBR
SHOCK SENSOR AMPIC5851
LCD DRIVER
IC4501
TIMING GENERATOR
IC4602
EVR
IC4502
Y/C VIDEOSIGNAL AMP
IC4002
IC4004
HP/LINEAMP
IC3007
SP AMP
IC3008
AD/DACONVERTER
IC3004
ATRACIC3009
Y/C VIDEOSIGNAL AMP
IC4001
IC4003
COMPOSITEVIDEO AMP
IC4005
LANCDRIVER
IC8027
MIC AMP
IC3001
SRAM
IC8808
ETHERINTERFACE
IC8806
DRIVE PULSE GENERATOR
BACK LIGHT
IC4601
SHOCKSENSOR
DETECT SWITCH
SE5851
DRIVECONTROL
IC5404
FOCUS/TRACKINGCOIL DRIVE
SLED MOTORDRIVE
IC5602
IC5007
HEAD SWITCH
DETECTOR
OPTICAL PICK-UPBLOCK
HR5901OVER WRITE HEAD
IC5901
TIMINGGENERATOR
IC101
M
IRIS DRIVE
HALL AMP
HALL BIAS/GAIN CONTROL
IC201
SENSORAMP
REMOTE CONTROLRECEIVER
FUNCTION KEY&
JOG
IC002
IC1
REAL TIMECLOCK
IC8008
SWITCHINGCONTROL SWITCHING
®ULATOR
UNREGBATT SIG
D3.1V4.95V (DRIVE)4.95V (VIDEO)4.95V (ETHER)4.95V (CAMERA)12V13V–6.5V–20VA2.85VD2.85V2.3V
IC9001
ZOOMSENSOR
FOCUSSENSOR
MFBLOCK
THERMALSENSOR
YAWSENSORSE001
SE201PITCH
SENSOR
HALLSENSOR
CAMERACONTROL
IC106
REC BOARD(SEE PAGE 4-79)
CLV BOARD(1/2)(SEE PAGE 4-75)
CLV BOARD (2/2)(SEE PAGE 4-75)
VF BOARD (SEE PAGE 4-87)
LCD BOARD (SEE PAGE 4-106)
JACK BOARD (2/2)(SEE PAGE 4-119)
JACK BOARD (1/2)(SEE PAGE 4-119)
REMOTE TERMINALUNIT (SEE PAGE 4-119)
MAIN CONTROL SWITCH UNIT (2/2)(SEE PAGE 4-62)
BL BOARD(SEE PAGE 4-97)
VC-216 BOARD(SEE PAGE 4-13, 17)
MAIN BOARD (SEE PAGE 4-29 to 59)
LCD DRIVER
IC4302
TIMING GENERATOR
IC4303
D/A CONVERTER
IC4301
INVERTER UNIT
IV4301
BACK LIGHT
FOCUSCOIL
LASERDIODE
SWITCH
TRACKINGCOIL
M5801SLED MOTOR
M
M5811HEAD UP/DOWN
MOTOR
M5821SPINDLE MOTOR
M
FG
J3003
AUDIO/VIDEO
J4001
S. VIDEO
J3002
J11
REMOTE
J3001
MICPLUG IN POWER
MIC2001
MIC1001
R CH
L CH
ETHERADAPTER
BATTERYTERMINAL
LINE IN
10BASE-T
ETHER BOARD (SEE PAGE 4-109)
REMOCON RAY-CATCHER BLOCK UNIT(SEE PAGE 4-65)
MAIN CONTROL SWITCH UNIT (1/2),ZOOM SWITCH UNIT (SEE PAGE 4-62)UPPER CONTROL SW SUB ASSY,LCD DETECTION SW,FLEXIBLE BOARD(SEE PAGE 4-65)
POWER BOARD(SEE PAGE 4-130)
SP3001(SPEAKER)
+
–
MPEG2RATE
CONTROL&
SYSTEMCONTROL
IC8501
LCDPANEL
LCDPANEL
TOUCHPANELPA
RALL
EL B
US
AUDIO & VIDEODATA CONTROL
IC8101
64M EDO DRAMIC8102 IC8103
SYSTEM CONTROL
IC8001
NV-RAM
IC5405
1M FAST SDRAM
IC5501
05
3-1 3-2
3-1. OVERALL BLOCK DIAGRAM
SECTION 3BLOCK DIAGRAMS
DCM-M1
TIMING GENERATORIC101
XSHD
CLPDM
XSHP
ZSG1
PBLK
AVD
ZV1
VGAT
VCK (CL)
CK
OSCO
OSCI
DSGAT
ID
SSK
AHD
SSO
SSI
SEN
RST
CAM
SCK
CAM
SI
CAM
SO
CS C
AM
CAM
RST
V1
V2
V3
VSHT
V4
H1
RG
H2
CCD IMAGERIC001
V3
V1
V2
V4
CCD OUT
RG
H2
SUB
X10136MHz
S/HAGCCDS
D0I
D9A/DCONVERTER
TIMING
CDS, AGC, A/D CONVERTERIC102
PGA CONT 2
PGA CONT 1
AGC
THRO
UGH
STBY
CAM
VD
CAM
FLD
CLPDM
CAMERA Y/C PROCESSIC105 (1/2)
30
29
2I
11
23
22 16 18 4021
AGC CONT 1AGC CONT 2
PBLK19
HDO
VDO
FLDO
40I
37
CO 0I
CO 3
YO 0I
YO 7
TGVD77TGHD
FRQ6OSC ADJIC104
ID
PBLK
ZV1
VGAT
ZSG1
TGVD
TGHD
ID
PBLK
ZV1
VGAT
ZSG1
CLPOB78
89I
80
AD 0I
AD 9
BUFFERQ001
4
3
2
1
10
H1 11
12
13
8
33
26
25
28
31
22
21
18
35 40393837
44
48
42
4
5
7
12
36
41
45
34
2
16
15
1
CLPOB 20
26
27
76
75
72
73
71
74
3
2
CHCK69
CAMERAY/C
PROCESS
53
MCKO 63
VCK 65
52
51
50I
47
45I
42
CN101 (1/2)
29
3
7
6
8I
15
16I
19
Y0-Y7
C0-C3
CAM HD
CAM VD
SPCKO
CAM DD ON
VC-216 BOARD (1/2)(SEE PAGE 4-13, 17)
2
A
1
05
TO A/V DATA CONTROL,VIDEO OUT(SEE PAGE 3-7)
TO SYSTEM CONTROL(SEE PAGE 3-15)
TO CAMERACONTROL(SEE PAGE 3-6)
TO CAMERA CONTROL(SEE PAGE 3-6)
B
CHROMA
REC
Y
VIDEO SIGNAL
SIGNAL PATH
Y/CHROMA
18MHz
13.5MHz
REC/PBH
7 Vp-p
REC/PB
2.24 Vp-p
HREC/PB
7 Vp-p
H
36 MHz
REC/PB
1 Vp-p
18 MHz
REC/PB
3.28 Vp-p
16.33 MHz
18 MHz
REC/PB
3.12 Vp-p
REC/PB
3.84 Vp-p
HREC/PB
3.04 Vp-p
VREC/PB
2.88 Vp-p
2VREC/PB
2.96 Vp-p
13.5 MHz
REC/PB
Approx.3.4 Vp-p
HREC/PB
3.04 Vp-p
VREC/PB
2.88 Vp-p
3-3 3-4
3-2. CAMERA SIGNAL PROCESS BLOCK DIAGRAM
DCM-M1
CAMERA CONTROLIC106
74
43
72
XTAL
EXTAL
LENS RST LED
C RESET
ZOOM RST SENSOR
YAW AD
PITCH AD
IRIS PWM
LENS THERMAL A/D
HALL AD
FOCUS RST SENSOR
LENS RST LED
ZOOM RST SENSOR
FOCUS RST SENSOR
XRST CAM
ZOOM SW AD
STBY GCAM
VD
FLD
XCS EEPROM SCK
DI
DO
XCS
RSTXWEN EEPROM
X10220MHz
40
41
3
51
AGC THROUGH
STBY
CN101 (2/2)
CAM VD
CAM FLD
AGC THROUGH4
56
27
28
1
6
2
3
4BUSYBUSY EEPROM 31 7
EEPROMIC103
CAM SI
CAM SO
CAM SCK
80
XRST CAM 38
XCS CAM 59
HI SI 60
HI SO 61
HI SCK 62
A3 ZA
A2.85V (CAMERA)
B3 ZA
A4 ZB
IN3
EN3
B4 ZB
IN4
EN4
18
19
8
22
10
20
A1 FA
B1 FA
A2 FB
IN1
EN1
B2 FB
05
12
13
IN2
EN2
14
15
5
26
7
24
ZOOMMOTORDRIVE
IC202 (1/2)
FOCUSMOTORDRIVE
IC202 (2/2)
16
17
ZM AM903ZOOM
MOTOR
M902FOCUSMOTOR
FC RST
ZM RST
BIAS –
HALL –
HALL +
BIAS +
DRIVE –
IRISMETER
DRIVE +
TEMP OUT
CN201
SENSE VCC
ZM XA
ZM B
ZM XB
FC A
FC XA
FC B
FC XB
M
M
M
FOCUSSENSOR
ZOOMSENSOR
–+
HALL GAIN CONTROLIC201 (3/4)
HALL GAINCONTROL
Q204
SENSOR VCCSWITCH
Q201
HALL BIAS CONTROLIC201 (2/4)
IRIS DRIVEIC201 (1/4)
HALL ANPIC201 (4/4)
HALL AD
12
1314
–+ 3
+–
108
–+
67
SE201
SENSOR AMPIC002
MF VCC SWITCHQ203
SE001
YAWSENSOR
PITCHSENSOR
4.95V(CAMERA)
9
LPFDRIVEQ202
12
16
19
18
8
42
2
4
2
4
16
7
19
73
85
20
2
CS CAM 98
SOFT V
CAM RST
CAM SI
CAM SO
CAM SCK
CS CAM
11
33
34
35
MF LED17
MF A30
22 MF B
ZOOM LENSUNIT
VC-216 BOARD (2/2)(SEE PAGE 4-13 to 17)
21
16
22
15
24
6
5
23
19
18
17
20
2
3
12
14
4
1
11
13
H
5
Vref 1
LIA 1OUT 1
CRST
OUT 2Vref 2
LIA 2
10
9
A2.85V (CAMERA)MF VCC
THERMALSENSOR
8
MF A, MF BMFBLOCK
24
23
22
21
20
28
FOCUS/ZOOM
MOTOR
DIR0A
DIR1A
DIR0B
EN1
SENS 0
SENS 1
DIR1B
EN0
HALL OFFSETIRIS
13
HALL GAIN12
HALL REF11
95
96
99
98
100
IRIS COM91
93
94
97
XSCK
SO
SI
SYS V
XCLR
SIOEACH
BLOCK
26
28
27
29
30
XHI SCK
DATA TO HI
DATA FROM HI
XCS CAM
XRST CAM
ZOOM SW AD TO MODE CONTROL(SEE PAGE 3-24)
TO CAMERA SIGNALPROCESS(SEE PAGE 3-4)
TO CAMERA SIGNALPROCESS(SEE PAGE 3-3)
TO SYSTEM CONTROL(SEE PAGE 3-15)
C
D
1
2
IRIS,FOCUS/ZOOM
IC105 (2/2)
20 MHz
REC/PB
1.22 Vp-p
3-5 3-6
3-3. CAMERA CONTROL BLOCK DIAGRAM
DCM-M1
MAIN BOARD (1/7)(SEE PAGE 4-29, 48, 53, 59)
CN8101 (1/3)
Y0 – Y7
C0 – C3
CAM_VDCAM_HDSPCKO
73
6
IO0
111110112
71IN
STBY
Y VIDEO SIGNAL AMPIC4004
Y VIDEO SIGNAL AMPIC4003
OUT4
1
IO1 72
IO3 84
EXVDEXHDVCLK
191XABSXARQ
190ACDI192ACDO194RCK4195
188 ACLK
XABSXARQ
SYS_ACDISYS_ACDOACLK
C0/CIM0
AUDIO & VIDEO DATA CONTROLIC8101
ID/CIN1ADC8/CIN2ADC9/CIN3
8ı
15
16ı
19
89•
91•
101•
109
92ı
98•
100
ADC0/YIN0ı
ADC7/YIN7
136 – 140•
142 – 147•
149 – 153•
155 – 158•
160 – 163•
165 – 169•
171 – 173
174 – 176•
178 – 184•
186 • 187
2 – 5 • 7 – 10 •
41 – 44 • 46 – 49 19 – 24 • 27 – 32
37 38 13 14
2 – 5 • 7 – 10 •
41 – 44 • 46 – 49
37 38 13 14
LCAS
UCAS
WE
RAS
LCAS
UCAS
WE
RAS
19 – 24 • 27 – 32
SA0
– SA
11
SA0
– SA
11
SD16
– S
D31
SD0
– SD
15
DATA BUS
ADDRESS BUS
64M EDO DRAM
IC8102
64M EDO DRAM
IC8103
TO AUDIO(SEE PAGE 3-18)
209DSYNCDCLK
203 MBCK128 PLL OUT
212
222
211123
MCLK
207DDI206DDO205
RCLK189
SCLK196SCLK_SYS
SO197SI198
MDTI200
RAS130DWE129CAS0135CAS1134CAS2132CAS3131
MLRCK
DSYNCDCLK
DDIDDO
SOTO MD SERVO(SEE PAGE 3-14)
TO MD SIGNALPROCESS(SEE PAGE 3-12)
TO MD SIGNALPROCESS(SEE PAGE 3-12)
SI
MDTIMLRCK 202
512FS
1DMBCK
2X1CK 3
X1Q
D-FFIC8104 (1/2)
6
2BUFFERQ4002 LPF
FL4002IN
STBY
OUTSAG
4
1
2•3
IN
STBY
C VIDEO SIGNAL AMPIC4002
C VIDEO SIGNAL AMPIC4001
COMPOSITE VIDEOSIGNAL AMP
IC4005
OUT4
1
2BUFFERQ4001 BPF
FL4001
BUFFERQ4006
IN
STBY
OUT4 2
1
VCC8
Y IN
C IN4
2OUT1, 2
BUFFERQ4005
IO2 83 BUFFERQ4007
IC4006
IC4006
IC4009
IC4009
1 7
6 3
1 7
6 3
VHD 66
VVD 67
6
4
CN3002(1/4)
3
1012
6
4
CN3003(1/4)
J4001
3
1012
1211103
CN4313(1/3)
4_JACK_DETVIDEO OUT
S_C
S_JACK_DET
S_Y
4
SWITCHQ4002, 4004
6•7
252426
CN4511(1/2)
2327
PANEL_Y
LINE OUT R
LINE OUT L
PANEL_R-YPANEL_B-YLCD_XHDLCD_XVD
EVF_YEVF_R-YEVF_B-YEVF_XHDEVF_XVD
Y
C
SG
GS
S. VIDEO
J3003 (1/2)
AUDIO/VIDEO
JACK BOARD (1/4)(SEE PAGE 4-119)
2Q9 2D
D-FFIC8104 (2/2)
12RSTTRST
XCS
220XINT219XWAIT218XWE0217XWE1215XWE2214XWE3213
210
XRD
HANDI
FSY
HANDOBITI
BITO
HANDOHANDI
FSY_INTMCLK_BUFF
SYS_BITISYS_BITO
S_JACK_DET4_JACK_DET
S_OUT_OFFC_OUT_OFF
32333436
X2CK11
1Q5 1D
D-FFIC8020 (1/2)
2
X1CK3
DRAMD0ı
DRAMD31
2 – 4•
224 – 227•
229 – 233•
235 – 240•
242 – 248•
250 – 256
5 – 8•
10 – 15•
17 – 23•
25 – 29•
31
DATA0ı
DATA31
ADDR1ı
ADDR23
DRAMA0ı
DRAMA11
A0 ıA1
1
DQ1 ı
DQ16A0 ı
A11
DQ1 ı
DQ16
FSY_INT
TO SYSTEM CONTROL(SEE PAGE 3-16)
SYSCHIP_INT
DEV_RESET
CPU_CS4_100
SYS_WAITDQMLL_WE0
RDDQMUU_ICIOWRDQMUL_ICIORDDQMLU_WE1
54•
52ı
46
37ı
41•
43ı
45
MEC0ı
MEC7
MVP0ı
MVP7SYS_MVP0 – SYS_MVP7
MEC0 – MEC7
A0 – A23
D0 – D31
05
ATO CAMERA SIGNALPROCESS(SEE PAGE 3-4)
3
4
5
6
8
TO MPEG ENCODE(SEE PAGE 3-9)
7
TO LCD(SEE PAGE 3-19)
E
TO EVF(SEE PAGE 3-21)
F
CHROMA Y
VIDEO SIGNAL AUDIOSIGNALY/CHROMAMD1
REC
PB
MD2
MD SIGNAL
SIGNAL PATH
VREC/PB
2.88 Vp-p HREC/PB
3.04 Vp-p
13.5 MHz
REC/PB
Approx.3.4 Vp-p
3.1 Vp-p
VREC/PB
HREC/PB
3.6 Vp-p
HREC/PB
2.32 Vp-p
HREC/PB
360 mVp-p
H
REC/PB
1.48 Vp-p
27 MHz
REC/PB
3.52 Vp-p
HREC/PB
700 mVp-p
H
REC/PB
1.12 Vp-p
3-7 3-8
3-4. A/V DATA CONTROL, VIDEO OUT BLOCK DIAGRAM
DCM-M1
1920474849505152
110111
104105107
5378
888990
23 32
12
7879
5859
22
7133
6
64
63
91
40•
43
RXDO•
RX_SYS39
•40
TXDO•
TX_SYS
ADA_REST TO AUDIO(SEE PAGE 3-17)AT_REST
AT_EXECAT_STROAT_INSLAT_MUTEAT_RECAT_ATRAC2AT_LEVEL3SP_BEEPHP_BEEPSP_NMUTEAMUTESP_VDDPWR_DWNMIC_ATTXWIND
MIC_JACK_DETHP_JACK_DETW_JACK_DET
ADA_REST
MPEG2 RATE CONTRL&
SYSTEM CONTROLIC8501
AT_RESTAT_EXECAT_STROAT_INSL
AT_MUTEAT_REC
AT_ATRAC2AT_LEVEL3
4801
8798949597
MEC_RESETCLK_OUTXIMBBSXCS1XRDXWRXCS2
5129
MVP_RESEM2D11 X2CK2Q
4JACK_DETS_JACK_DETC_OUT_OFFS_OUT_OFF
4JACK_DETS_JACK_DETC_OUT_OFFS_OUT_OFF
SP_BEEPHP_BEEP
SP_NMUTEAMUTE
SP_VDDPWR_DWN
MIC_ATTXWIND
MIC_JACK_DETHP_JACK_DETW_JACK_DET
ETHER_RESET
CN8007(1/3)
CN4313(2/3)
ETHER_RESET
DEV_RESETRATE_RTS
RATE_TX
RATE_RX
RATE_CTS
XRESETRATE_RTS
RATE_CTS
X1
X2
X85016.6MHz
9
TO SYSTEM CONTROL(SEE PAGE 3-15)12
TO MODE CONTROL(SEE PAGE 3-24)10
TO MD SERVO(SEE PAGE 3-14)11
G
V_REC_LED V_REC_LED
A_REC_LED A_REC_LED
RIGHT RIGHT TO LCD(SEE PAGE 3-19)
TO ETHERINTERFACE(SEE PAGE 3-25)
HDOWN
DRV_RESETDRV_RESET
DOWN
173
59 58 57 84
17 18 19 68
62170164168166167
XRST
A0 – A5
MB DATAPROCESSOR
MOTIONESTIMATION
ADAPTIVE PREFILTER
CHROMA POSTFILTER
DRAM INTERFACE
ENCODE SEQUENCECONTROL
HOST
INTE
RFAC
EVIDE
OIN
TERF
ACE
MB
DATA
INTE
RFAC
E
D0-D15
XWE
CAS
RAS
SCLK
64M SDRAMIC8602
MPEG2 ENCODERIC8601
MPEG2 VIDEO PROCESSORIC8701
VE0 – VE7
VDD0 – VDD7
FSY
VDI0 – VDI7
ENDT0 – ENDT7
CLK
FSY_INT
MCLK_BUFF
WE
CAS
PAS
CLK
2 • 4 • 5 • 7 • 8 • 10 • 11 • 13 • 31 • 33 • 34 • 36 • 37 • 39 • 40 • 42 • 45 • 47 • 48 • 50 • 51 • 53 • 54 • 56 • 74 • 76 • 77 • 79 • 80 • 82 • 83 • 85
1 – 4 • 6 – 8 • 10 • 11 • 13 – 16 • 18 • 19 • 21 – 28 • 30 – 32 • 44 – 38 • 40
41 – 43 • 45 – 48 • 50 – 55
22 – 27 • 60 – 66
850D0 – 850D15 850D0 – 850D15
850A1 – 850A6
DRE0
– D
RE31
DR0
– DR
31
BA0,
BA1
,AD
E0 –
ADE
9
BA0,
BA1
,AD
0 –
AD9
850A0 – 850A6
PLLI(FN)XIMB
BSXCSXRDXWR
106103101102
127l
134•
136l
143
137 • 138•
140 – 143•
145 – 148•
150 – 153•
155 • 156
157•
158•
160l
163
119l
125
D0l
D15
A0l
A6
HOST
INTE
RFAC
EMB
DATA
INTE
RFAC
E
POST
FILT
ER
VIDE
OIN
TERF
ACE
DRAM INTERFACE
16M EDO DRAMIC8702
16M EDO DRAMIC8703
D-FFIC8020(2/2)
VARIABLE LENGTHCODINGENCODER
BIT STREAM MANAGER
ENDT0 – ENDT7
FSY
CLK
SYS_BITI
05
SYS_BITOHANDOHANDI
VOUT0 – VOUT7
LOCALDECODER VARIABLE LENGTH
DECODING
DQ0
lDQ
31
A0 lA1
2
103•
104•
106l
111
94l
99•
101l
102
113l
120
128l
135
122
175
MEC0 – MEC7
SYS_MVP0 – SYS_MVP7
TO A/V DATA CONTROL,VIDEO OUT(SEE PAGE 3-8)
7
92
63 61 62
106
112
107 108
1
110
17 18
9190
111•
118
84l
89
75l
82
RSTTRST
XWRXRDXCS
A0 – A5
D0 – D7
12 – 14 • 16 – 19 • 21 – 24 • 26 – 36 • 38 – 43 • 45 – 48
2 – 5 • 7 – 10 •41 – 44 • 46 – 49
21 – 24 • 27 – 32
49 • 50 • 52 – 57 • 59 • 60
RD0
– RD
31
RA0
– RA
9
XWE
BITO
BITI
HAND
OHA
NDI
RAS
CAS
VD0
– VD
31
MVP
0 –
MVP
7
ENDT
0 –
ENDT
7
VA0
– VA
9
VD0
– VD
15
VA0
– VA
9
VD16
– V
D31
VA0
– VA
9
WRI
TERA
S
34 • 35
I/O1 l
I/O16
A0 l A9 UCAS •
LCAS
17 18
WRI
TERA
S
34 • 35
UCAS •
LCAS
850D0 – 850D7
850A0 – 850A5DA
TA B
US
ADDR
ESS
BUS
2l9•
11
65l
68•
70l
73
MAIN BOARD (2/7)(SEE PAGE 4-33, 59)
2 – 5 • 7 – 10 •41 – 44 • 46 – 49
21 – 24 • 27 – 32
I/O1 l
I/O16
A0 l A9
6.6 MHz
REC/PB
1.12 Vp-p
27 MHz
REC/PB
3.52 Vp-p
3-9 3-10
3-5. MPEG ENCODE BLOCK DIAGRAM
DCM-M1
MONITORCONTROL
CLOCKGENERATOR
MAGNETICHEADDRIVE
SIGNALGENERATOR
CPU
INTE
RFAC
E
MNT0
OSCIX5403 70.54MHz
OSCO
MNT2
SQSY
XINT
DQSY
SRDTSWDTSCLKXLATSENS
APCREF
RECP
IC5303
FOCNT
ADFG
FS4FS4
FILOCLTVPCOFILI
ASYOASYO
ASYI
RFI
VCVC
A_B
SISCLK SVXLAT SV
SENS
MNT1
LRCK
DADT
XRST
FS256XBCK
MDTI
512FS
MLRCKMBCK
LRCK
DADT
256FSXBCK
XINTDQSYSQSY
6
17
16
15
5
BUFFERIC5302
24
10
67
55
52
51
59586160
78
13
83
252627
12
1617
3
85679
1211
ATRA
CEN
CODE
R/DE
CODE
R
HEADSWITCHIC5901
OVERWRITEHEADDRIVEQ5902,5903
LASERCLOCK
GENERATOR
A/DCONVERTER
IC5102
SHOE
H PR
OOF
MEM
ORY
CONT
ROLL
ER
DRAM
PLL
FILT
ER
COM
PARA
TOR
14
SUBCODEPROCESSOR
PWMGENERATOR
SPIN
DLE
SERV
OAD
IPDE
CODE
R
90
79
EFM
/ACI
RIC
ENCO
DER/
DECO
DER
MON5(HP-L)
CLK
LSRC
K
MHE
N
ADCCK
RECP
MON4(HP-H)MON3(HN-L)MON2(HN-H)
HP-L
MHEN
RFGAIN UPRFGAIN DOWN
HP-HHN-LHN-H
CN5002(1/2)
CN5803(1/2)CN5902CN5901
5678
37
12
VIN21
89
41
HP-L
MHEN
Q5901
HP-HHN-LHN-H
OUT B
HR5901OVER WRITE HEAD
OUT A2, 36, 74, 58, 9
17, 1813, 1415, 1611, 12
1l8
ADRF0l
ADRF7
RAM
ADR0
lRA
MAD
R16
RAM
DAT0
lRA
MDA
T17
87l
80
D0l
D7
43
44
31
2928
4039
19
42
36
96
1817 32 33 34 35
CLOCKGENERATOR
SYNCGENERATOR
SYNCSELECTOR
SERIAL COMMANDINTERFACE
MD1 DIGITAL SIGNAL PROCESSORIC5301(1/2)
MD2 DIGITAL SIGNAL PROCESSORIC5403(1/2)
1M FAST SRAMIC5501
XBISY
XOE
XWE
A0 lA1
6
I/O1 l
I/O8
OE WE
DIN
REFCK
DSYNC
DDO
DCLK
X5301 22.5792MHzOSCI
OSCO
EDENEDIEN
XSCSY
EDENEDIEN
XSCSY
TO/FROMADIP D OUT DDI
MD1X2 MD1X2
SRDTEX
XCLRIOBUSY XEM
GSR
DTSW
DTSC
LK
XLAT
DRV
RESE
T
XLAT
DDX
DRV
RESE
T
MAIN DATA SIGNALPROCESSING
56 – 62 • 64 – 73
1 – 4 • 13 – 21 • 29 – 32
6 • 7 • 10 • 11 • 22 • 23 • 26 • 27
46 – 50 • 53 – 55 74 75
28 12
5CS SRAM CS
43444546
50
43444546
50
1234
5
CLV BOARD(1/2)(SEE PAGE 4-75)
MAIN BOARD (3/7)(SEE PAGE 4-39, 43)
REC BOARD(SEE PAGE 4-79)
1•24•5
19
40
461
48 47
2
8
9
4
5
6
7
27
161718
38
3736
4241
28
26
32
35
3433
20
XSTBY
PIGPIG
RFO
MOFROCN5001
I2425
3 VCVC
VC
JIJ
MOFRI
AGCI
RF AMPFOCUS/TRACKING
ERROR AMPIC5002
SWDTCOMMANDSCLKXLAT
DTRFCKRFXLRF
RF
EQ
PEAKBOTM
EFWBLGHWBL
SE
TE
ADFG
ABCD
FE
TEMP AUX1
FOCNT
DPP
AD7
WRITE PWM I GAIN
XKSHOCK
J GAIN
WBLEQ
MODE
SERIALCOMANDDECODER
A/B TRACKDETECT
IC5201, 5205(2/2)Q5201, 5202
CENTER VOLTAGEGENERATOR(FOR BIAS)
AUTOMATICPOWER CONTROL
IC5005, Q5002
RF AGC& EQ
RF AMP
GAIN CONTROL AMPIC5003, Q5005
L. P. F.FL5101, Q5101
WBL
WBL
ADFM ADIN
B.P.F.WBLAMP
AMP
WBL
PEAK & BOTTOMHOLD
SLED ERRORAMP
TRACKINGERROR AMP
ADDE
R/SU
BTRA
CTER
ATAMP B.P.F
I-VAMP
PIG
EF(XE)
HG(XF)
E&F
G&H
A
B
C
D
A
B
C
D
ABCDAMP PIG
IC5007
IC5008
17
6
53
5 6 21
7
FOCUS ERRORAMP
BUFFERIC5006(1/2)
COMPARATORIC5205(1/2)
V-ICONVERTER
29 30
30
DETECTOR
28
21
27
23
22
26
31SEL
XLDON
VLPC
PD-A
05
16
13
LASERDIODE
11
13 14
G&H
E&F
IC
D
B
AJ
LDPD
OPTICAL PICK-UP BLOCK (1/2)
412
MD1
REC
PB
MD2
MD SIGNAL
SIGNAL PATH
MD1/MD2
100
19
TO A/V DATA CONTROL,VIDEO OUT(SE PAGE 3-7)
TO MD SERVO(SE PAGE 3-14)
TO MD SERVO(SE PAGE 3-14)
TO MD SERVO(SE PAGE 3-14)
TO AUDIO(SE PAGE 3-17)
TO A/V DATACONTROL,VIDEO OUT(SE PAGE 3-7)
TO MD SERVO(SE PAGE 3-14)
200 nsPB (MD1)
Approx.324 mVp-p
100 nsPB (MD2)
Approx.360 mVp-p
200 ns PB (MD1)
Approx.712 mVp-p
PB (MD2)
100 ns
Approx.280 mVp-p
200 ns
PB (MD1)
Approx.200 mVp-p
22.5792 MHzREC/PB
980 mVp-p
70.54 MHzREC/PB
320 mVp-p
PB
Approx.1.54 Vp-p: MD1Approx.1.86 Vp-p: MD2
PB
200 ns: MD1100 ns: MD2
200 ns: MD1100 ns: MD2
Approx.1.22 Vp-p: MD1Approx.880 mVp-p: MD2
3-11 3-12
3-6. MD SIGNAL PROCESS BLOCK DIAGRAM
DCM-M1
1•2
5•6
3•4
7•8
6 16FO1FFDR PEAK
TO MD SIGNAL PROCESS(SEE PAGE 3-11)
TO MD SIGNAL PROCESS(SEE PAGE 3-11)
TO MD SIGNAL PROCESS(SEE PAGE 3-12)
TO A/V DATA CONTROL,VIDEO OUT(SEE PAGE 3-7)
TO MD SIGNAL PROCESS(SEE PAGE 3-12)
TO SYSTEM CONTROL(SEE PAGE 3-15)
TO MPEG ENCODE(SEE PAGE 3-10)
BOTMABCD
FEAUX1
SETE
XLRF
FROM CPUINTERFACE
CKRFDTRF
FS4
FE
X540116.9344MHz
NV-RAMIC5405
TE
XKSHOCK
FRDR
TFDR
TRDR
SFDRSRDR
FOCUS/TRACKING COIL DRIVE,SLED MOTOR DRIVE
IC5602
DIGITAL SERVO SIGNAL PROCESSORIC5301 (2/2)
2-AXIS DEVICE FCS+
CN5001
FCS–
TRK+
TRK–
(FOC
US)
(TRA
CKIN
G)
FI1
8 15RO1 RI1
31 21FO3 FI3
29 22RO3 RI3
13 17FO2 FI211 18
88
65667374
808182
646362
89
86
85
9291
3 2
RO2
XPS CLK
RI2
TRACKINGMONITOR
IC5006 (2/2)
DIGITALSERVOSIGNAL
PROCESS
PWM
GEN
ERAT
OR
A/D
CONV
ERTE
R
ANAL
OG M
UX
AUTOSEQUENCER
L.P.F.IC5011,
5012
ERROR LEVELDETECTIC5004
DETECT LEVELCONTROL
IC5009,5010
PWM
(P67
)
A/D
DPP
WRI
TE P
WM
I gai
n0J
gain
0
AD7
DPP
WRI
TE P
WM
I GAI
NJ
GAIN
TELEVELINTRRUPT
IC5013
KSHOCKENABLEIC5014
68
38
7 12 39 57 59
XOUT
19
XIN
20
86
85
61
6
41
53
54
55
56
95969798
45
4 32
33279970
65
64
63
67
18 26 28 48 49 66 71 81 82 83 87 93
9
72737475
1713
46
40
94
94
98
97
47
42
43
44
88
3138
21
23
20
27
28
29
1
3
5
2
4
6
14
30
16•
18
36•
37
31
35
38
5
6
3
1
4
2
21
23
20
27
4
162
7
5
16
7
5 3
1
2
28
29
1
3
5
2
4
6
14
30
16•
18
7•9
31
35
SHOCKSENSOR
SE5851
SHOCK SENSOR AMPIC5851
HEAD UP/DOWN MOTOR DRIVEIC5601 SYS_SEL
MHE
NPI
GXS
TBY
SI SCLK
SV
XSCS
YIO
BUSY
SWDT
SCLK_SYS
SRDT
SCLK
RFGA
IN_U
PRF
GAIN
_DOW
NM
D1X2
XLAT
_DDX
SRAM
_CS
SO
SI
EDEN
EDIE
NXE
MG
A_B
NV_DINV_DO
NV_CLKNV_CS
RESET
30
SYS_
CS
DIDOSK
DRV RESET
DRV REQ
DRV
RESE
T
CS PI
SCLK
SRDT
SWDT
XLAT SVSENSXINT
DQSY
CLV_W_MON
CLV_V_MON
CLV_U_MON
CLV_W_CON
CLV_V_CON
CLV_U_CON
TEMP MON
INITIALMD1_MD2REFLECTPROTECTINLMIT
ST2B
ST2A
ST1B
ST1A
SLED2_MON
SLED1_MON
MR_ADJ
SE2_MON
PS_36
SHOCKKSHOCK EN
XKSHOCKTELEVEL INT
SQSY
CLV_VCON
SPRDCL
V_BR
AKE_
EN
S5801PROTECT
XB (2B)
B (2A)
U
V
W
05
COM
XA (1B)
A (1A)
VO1, VO2
SLED–
SLED+CN5801
M5801SLED MOTOR
M5811HEAD UP/DOWN
MOTOR
M5821SPINDLE MOTOR
PROT
ECT
REFL
ECT
MD
1_2
INIT
IAL
INLM
IT
SIA
SIBOUT
14
2
M
M
FG SLED MONITORIC5802, 5807
REFERENCE VOLTAGEGENERATOR
IC5401
SPINDLE VOLTAGECONTROL
Q5801-5803
OUT 1A IN 1A
OUT 1B IN 1B
OUT 2A IN 2A
OUT 2B IN 2B
2
3
16
15
7
10
5
12
S5802REFLECT
(DISK TYPE JUDGMENT)
S5803MD 1/2
S5804INITIAL
S5805IN LIMIT
HEADUP/DOWN
OPTICALPICK-UP
POSITION
100
OUT
TEMPERATURESENSORIC5406
DIGITAL SERVO SIGNAL PROCESSORIC5403 (2/2)
READ DATA SELECTIC5408
SCLK SELECTIC5407
IC5015
SHOCK
CN5803(2/2)
CN5002(2/2)
SLED0_MONSLED1_MON
SD+
SD–
MR_REF
1A
1B
2A
2B
CLV_U_CON
CLV_V_CON
CLV_W_CON
CLV_VCONT
CLV_U_MON
CLV_V_MON
CLV_W_MON
4
SPINDLEMOTORDRIVE
Q5821-5826
PHASECONTROL
IC5804-5806,5808
SPINDLEMOTOR
PRE-DRIVEQ5808-5813
SPINDLEMONITOR
IC5801, 5803
SPINDLECONTROL
SPINDLE DRIVESIGNAL SLECTOR
IC5402
90
92INTERVALCOUNTER
TO SERIAL COMMANDINTERFACE
ADIPDECODER
&SPINDLESERVO
ADFGADIPFMSPFDEX
SPRD
SPRD
ASYORFEX
3421 7
CLV BOARD (2/2)(SEE PAGE 4-68)
DRIVE CONTROLIC5404
MAIN BOARD (4/7)(SEE PAGE 4-39, 43)
OPTICAL PIC-UP BLOCK(2/2)
13
14
11
19
15
4
17
Approx.23.6 ms: MD1 Approx.14.8 ms: MD2
REC/PB
Approx.1 Vp-p: MD1Approx.1.32 Vp-p: MD2
Approx.1.38 Vp-p: MD1Approx.1.68 Vp-p: MD2
Approx.23.6 ms: MD1Approx.14.8 ms: MD2
REC/PB
Approx.560 mVp-p: MD1Approx.780 mVp-p: MD2
Approx.23.6 ms: MD1Approx.14.8 ms: MD2
REC/PB
Approx.12 ms: MD1Approx.7.5 ms: MD2
REC/PB
3 Vp-p
16.934 MHzREC/PB
1.58 Vp-p
3-13 3-14
3-7. MD SERVO BLOCK DIAGRAM
DCM-M1
MAIN BOARD (5/7)(SEE PAGE 4-48, 59)
CLE
UDQM
X800132kHz
RFAL TIME CLOCKIC8008
SYSTEM CONTROLIC8001
CLOCK_EN
OSC OUT
OSC IN
DQMUU_ICIOWR
RD/WT
DQMUL_ICIORD
3
2
4
7
8
9
92
93
2
ALE3
43
41
15
UDQM
39
/WE
16
/CE
19
/CAS
17
/RAS
18
CKE
37
CLK
38
VOUT 3
VCC 4
91
CN8101(2/3)
21
20
24
22
29
23
DATA_TO_HI
XHI_SCK
DATA_FROM_HI
CAM_XCS
CAM_RST
CAM_DD_ON
LCD_SI
LCD_SCK
LCD_SO
LCD_EN_SWED
IC8007
IC8025
IC8006
TO CAMERA CONTROL(SEE PAGE 3-6)
TO AUDIO(SEE PAGE 3-17)
167 CAM ENABLE
186 CAM PWR
184 CAM RESET
171
182
LCD_EN 103
EVF_EN 107165
164
189
SO
SCLK
SI
CE
190
CAM_SI
CAM_SCK
CAM_SO
ATRAC2_EN
ADA_EN
CAM_SI
CAM_SCK
CAM_SO
ATRAC2_EN
ADA_EN
DRV_REQ169 DRV_REQ
155 XTAL
156 EXTAL
XTAL2
EXTAL2
168
170
174
176
RATE_TX
RATE_RTS
RATE_RX
RATE_CTS
DEV_RESET
RATE_TX
RATE_RTS
RATE_RX
RATE_CTS
177 DEV_RESET
193 XRESET
185 DRV_PWR
X800232KHz
4
5
X80039.8304MHz
SWITCHQ8005
SWITCHQ8013
SWITCHQ8014
RESETIC8009
IC8010
SH_3.1V
IC80236
4
224
1
1
2
IC8013
05
CN4312(1/2)
3
14
2
1
TO LCD(SEE PAGE 3-19)
IC400726
1
IC4008
2 6
1IC4008
5 3
7
IC4007
5 3
7
EVF_SI
EVF_SCK
EVF_SO
EVF_EN_SWED
CN4511(2/2)
CN4313 (3/3)
9
10
8
7
IC401026
1
IC40112 6
1IC40115 3
7
IC40105 3
7
ETHER_PWR
SBHE_CE2B
CN8007(2/3)
36
27
ETHER_INT33
CS6_ETHER
ETHER_WAIT
SYS_WAIT
SYSCHIP_INT
FSY_INT
CPU_CS4_100
DEV_RESET
A0 – A3
D0 – D15
DQMUL_ICIORD
DQMUU_ICIOWR
RD & WT
DQMUL_ICIORD
DQMUU_ICIOWR
DQMLL_WE0
DQMLU_WE1RD
26
DQMLU_WE1
CS3_SDRAM
DQMLL_WE090
99
98
96
89
ETHER_PWR 94
ETHER_INT 138
SBHE_CE2B 104
CS6_ETHER 102
13 – 18 • 20 •
22 – 26 • 28 •
30 – 32 • 34 •
36 – 44 • 46 •
48 – 52
53 – 56 • 58 •
60 – 68 • 70 •
72 – 78 • 80 • 82
20 – 26 •
29 – 35
2 • 4 • 5 • 7 • 8 • 10 •
11 • 13 • 42 • 44 • 45 •
47 • 48 • 50 • 51 • 53
A0 ıA1
3
DQ0 ı
DQ15
UDQM
15
UDQM
39
/WE
16
/CE
19
/CAS
17
/RAS
18
CKE
37
CLK
38
20 – 26 •
29 – 35
2 • 4 • 5 • 7 • 8 • 10 •
11 • 13 • 42 • 44 • 45 •
47 • 48 • 50 • 51 • 53
A0 ıA1
3
DQ0 ı
DQ15
CAS 108
RAS3L 106
CKE 105
KIO 162
123
137
139
100
WAIT
CS2_FLASH
88RD
SYSCHIP_INT
FSY_INT
CS4_SYSCHIP
110CLE
112ALE
113CE
191RDY_BUSY
CSO_ROM
2
14
2
14
1
24
28
29
34
31A2
– A
13,
A22,
A23
A2 –
A13
, A2
2, A
23
D16
– D3
1
D0 –
D15
64M SDRAMIC8002
64M SDRAMIC8003
64M FLASHIC8005
DATA BUS
ADDRESS BUS
DATA
BUS
ADDR
ESS
BUS
D0–D15
A0 – A3
D0 – D31D0 – D7
A0 – A23
D0 – D7
A0 – A16
1ı4•6ı9•
11ı
13•
15ı
19
21ı
24
424
5
18ı
21•
24ı
27
I/O-0ı
I/O-7
REWE
WP
CE
R/B
30
32
9
1M EEPROMIC8004
21ı
23•
25ı
29
I/O-0ı
I/O-7
A0ı
A6
A0ı
A23
D0ı
D31
OE
5 WE
CE
RDY/BAO
6 RES
SWITCHQ8012
1ı4•7•
10ı
20•
31
C
TO CAMERA SIGNAL PROCESS(SEE PAGE 3-4)
B
18
TO MD SERVO(SEE PAGE 3-14)
19
TO MPEG ENCODE(SEE PAGE 3-10)
12
I
TO EVF(SEE PAGE 3-21)
J
TO ETHER INTERFACE(SEE PAGE 3-25)
K
TO A/V DATA CONTROL,VIDEO OUT(SEE PAGE 3-8)
8
32.768 kHz
REC/PB
408 mVp-p
9.8304 MHz
REC/PB
1.1 Vp-p
qg
32.768 kHz
REC/PB
1.5 Vp-p
qh
3-15 3-16
3-8. SYSTEM CONTROL BLOCK DIAGRAM
DCM-M1
MAIN BOARD (6/7)(SEE PAGE 4-48, 56)
JACK BOARD (3/4)(SEE PAGE 4-119 )
MAIN CONTROLSWITCH UNIT(1/2)(SEE PAGE 4-62)
ETHER BOARD(1/2)(SEE PAGE 4-109)
JACK BOARD (2/4)(SEE PAGE 4-119)
ETHER ADAPTER(1/2)
1
CN8802(1/2)
353
CN8801(1/2)
5553
CN8007 (3/3)
55
19 59 59LINE_R
W_JACK_DET W_JACK_DET
LINE_LLINEIN_RLINEIN_L
21
CN3003 (2/4) CN3002 (2/4)
3026
MICIN_RMICIN_L
EXT
INT
EXT
INT 2
31
6
57
21
3026
MIC_JACK_DET
MIC2001
MIC1001
R CH
L CH
CN3001
XWIN
D
29
2
18
19
17
13
14
44
43
41
40
36
31
38
37
+– +
–
+–
+–
+–
+– +
–
HPF
HPF
FILTER
BIAS
FILTER
24
23
11
12
8
6
2120109
1
4
2
3
ON
OFF
OFF
ON
RIN3
LIN3
RIN2ADCR
ADCLLIN2
PGAR
PGAL
IC3002
RIN1
LIN1
XRST
PD
35
32
OPGAL26
OPGAR23
LOUT1
ROUT1
LOUT229
ROUT228
INR15
OUTR8
VCOM
OUTL
LOUTR
NF14
NF2
LOUTL
INL16
LINR
LINL
47
XCS
CCLK
CDTO
CDTI
MCL
K
SDTI
12 13 14 15 1
BCLK
3
LCLK
2
SDTO
46
25
24
ADCONVERTER
DACONVERTER
CONTROLREGISTER
I/F
CLOCKDIVIDER
6
18
13
9
11
17
14
VREF
MUTE
SD BIAS
BEEP
MUTE BEEP23 21
2
7
INVERTERQ3002
SP SWITCHIC3003
MIC AMPIC3001
SP AMPIC3008
3
5 6
3
1
45
1
AD/DA CONVERTERIC3004
HP/LINE AMPIC3007
15
17
CN3002 (3/4)
11
20
1619
15
17
CN3003 (3/4)
11
20
1619
HP_COM
HP_R
VIDEO OUT
4 JACK DET
HP_L
LINEOUT-L
LINEOUT-R
SP_IN
SP+
CN8001(1/2) CN8301 (1/2)
SP–
18•
20
17•
19
SP3001(SPEAKER)17
•19
18•
20
ACLK
SHOCKPROOF
I/F
MICROCOMPUTER
I/F
AUDIO I/F
IC3005
2
4
ACDIXABSACDOXARQ
ACLKSYS_ACDOXABSSYS_ACDIXARQ32
31292825
SCLK
XRST
EXTAL
SWDTXLATLEXCSTROMTERECATRAC2LEVEL3
CAM_SCK
AT_RESET
512FS
TO MPEG ENCODE(SEE PAGE 3-10)
CAM_SOATRAC2_EN
AT_EXECAT_STROAT_MUTEAT_RECAT_ATRAC2AT_LEVEL3
202324394046474950
15
19
DSP COREDATA
RAM & ROMPROGRAM
ROM
CLOCKGENERATOR
RESETCIRCUITR
333545 36 38 34
5 4
AMUT
EHP
_BEE
PHP
_JAC
K_DE
TSP
_NM
UTE
XBCK
AT_I
NSL
LRCK
JNSL
DIDT
DODT
BCK
LRCK
AIDT
CAM
_SO
CAM
_SI
CAM
_SCK
ADA_
EN
256F
S
MIC
_JAC
K_DE
T
W_J
ACK_
DET
MIC
_ATT
ADA_
RESE
TPW
R_DW
N
DADT
SP_B
EEP
SP_V
DD
05
ATRACIC3009
J3003 (2/2)
AUDIO/VIDEO
LINE IN
J3001
MICPLUG IN POWER
25
AUDIOI/F
CONTROL
ATTSWITCHQ3001
9
TO MD SIGNAL PROCESS(SEE PAGE 3-12) 16
TO SYSTEM CONTROL(SEE PAGE 3-15) 18
TO A/V DATA CONTROL,VIDEO OUT(SEE PAGE 3-7)
3
AUDIOSIGNALMD1
REC
PB
MD SIGNAL
SIGNAL PATH
J3002
30
11.2896 MHz 44.1 kHz
2..8224 MHz
REC/PB
3.84 Vp-p
REC/PB
4.24 Vp-p
REC/PB
4.32 Vp-p
3-17 3-18
3-9. AUDIO BLOCK DIAGRAM
DCM-M1
LCD BOARD (1/2)(SEE PAGE 4-106)
UNREG
LCD_4.95V
BL_L
VL
CLK
DI
A10
A12
19
17
20
A02
A05
A01
XHDXVD
DOWN
RIGHT
LCD_XHDLCD_XVD
PANEL_B-Y
PANEL_R-Y
PANEL_Y
DOWN
RIGHT
LCD_EN_SWED
LCD_SI
LCD_SCK
LCD_SO
A06
A04
A03
A07
2
5
1
6
4
3
7
6
40
39
30
31
32
35
G/Y
COM_AMP
COLOR
EXT_
BGP
BLAC
K IN
VCO
V_CO
M
XTES
T
COM
_AM
P
FRP
COM
_FRP
CONT
BRIGHT
RGB_AMP
SUB_BRT_B
SUB_BRT_R
8
R/R-Y/CR9
B/B-Y/CB10
G_OUT22
R_OUT20
B_OUT24
COM_OUT41
14 48
12
A118
A099
A08
BL_LVL
V_COM
VCO11
DO
10
47
1
2
DOWN
BGP
SW
3
9
SW_COM
FRP
10
11
HDB
SYF
MCLK
4
33
PD 32
OSCO 26
OSCI 27
24
OE 23
44
PHOIN
PHOOUT
COMTST
TG-20, TG-21, TG-22
TG-24
TG-23
TG-18
TG-17
TG-16
TG-15
TG-14
TG-13
TG-12
3
4
5
14
14
CN4303
20
CN4306BUFFER
Q4303, 4304
BUFFERQ4305, 4306
BUFFERQ4307, 4308
CLAMP MATRIX
PICTURE
CLAMPGCA CLAMPGAMMA INV
38 37 29 28
18 CS/LD
RIGHTO 18
RESET 17
GSRT 16
GPCK 15
GRES 14
DOWNO 13
HCNT 12RIGHT46
QVD/XVD34
CSY/XHD
DOWN
05
RIGHT
XVD
XHD37
22ı
20
SRT1ı
SRT3
FILTERIC4304 (1/2)
COM DRIVEQ4312, 4313
INVERTERUNIT
IV4301
VCO
+–6
75
CN4302 (1/2)
CN4307
D4317(LED)
CN4305
FLUORESCENTTUBE
ND4307BACK LIGHT
D/A CONVERTERIC4301
TIMING GENERATORIC4303
COM AMPIC4304 (2/2)
LCD DRIVERIC4302
VGL
LCD_4.95V (VSH)
VG
VR
VB
VGH
2.85V (TG) (VDO)
HCNT
OE
MODE1
MCLK
SRTR
MODE2
SRTL
SRTM
GPCK
GRES
CS
VCOM
RESET
GSRT
LED
BL_GND
BL_HIGH
BL_LOW
HSY
SYF
BL (+)
BL (–)
PANEL_COM
XTST
VG
PANEL_XHD
LCD_–15V
LCD_4.95V
LCD_13V
LCD_2.85V
FOR JIG
LCDPANEL
LCD UNITLCD4301
11
12
13
1
12
13
22
21
1
2
3
24
18
17
16
15
14
13
12
9
8
7
6
5
23
10
3
9
4
6
7
8
1
2
10
3
2
1
TG-18
TG-24
TG-12
TG-23TG-22
TG-21
TG-20
TG-13TG-17
TG-16
TG-15
TG-14
HTO MPEG ENCODE(SEE PAGE 3-10)
ETO A/V DATA CONTROL,VIDEO OUT(SEE PAGE 3-8)
ITO SYSTEM CONTROL(SEE PAGE 3-16)
CHROMA Y
VIDEO SIGNAL
PB
SIGNAL PATH
HREC/PB
560 mVp-p
HREC/PB
220mVp-p
H
REC/PB
236 mVp-p
3.1 Vp-p
VREC/PB
HREC/PB
3.6 Vp-p
REC/PB
3.12 Vp-p
15.4 MHz
2H
REC/PB
4 Vp-p
2H
REC/PB
4 Vp-p
REC/PB
2H
4 Vp-p
2H REC/PB
1.26 Vp-p
3-19 3-20
3-10. LCD BLOCK DIAGRAM
DCM-M1
VF BOARD(SEE PAGE 4-87)
EVF_B-Y
EVF_SO
EVF_SCK
EVF_SI
EVF_EN_SWED
EVF_R-Y
EVF_Y G/Y8
R/R-Y/CR9
B/B-Y/CB10
G OUT22
R OUT
BLK
HCK1
20
B OUT24
CN4501 CN4601
BUFFERQ4502, 4503
SWITCHINGQ4701
BUFFERQ4504, 4505
BUFFERQ4506, 4507
CLAMP MATRIX CLAMP GAMMA CLAMPS/H
PICTUREAGC
GCAINV
FTO A/V DATA CONTROL,VIDEO OUT(SEE PAGE 3-8)
INV CURRENT
VCO
8
18
7
AGC
PICTURE
COLOR
CONTRAST
BRT
D_CLIP
SUB_BRT_B
11
10
2
5
1
6
4
5
1
6
40
39
27
31SUB BRT B
SUB_BRT_R 3 32SUB BRT R
AGC LEVEL
PICTURE
COLOR
GAMMA1 9 33GAMMA1
CONTRAST
BRIGHT
BLACK LIMITLD
19 CLK
17 DO
20 DI
EVRIC4502
41
42
XHD
SH1
SH3
SH0
32
34
30
SH2
XCLP
38
35
SBLK
FRP
5
28
BLK 12
CLR 1627
CKI
CKO
39 RPD
CLR
BLK
EN
VSTVCK2
VCK1
HST
HCK2HCK1
EN 17
VST1 18
VCK2 20
VCK1 21
HST1 22
HCK2 23
HCK1 24
XVD45EVF_XVD
EVF_XHD
LCD TIMING GENERATORIC4602
DRIVE PULSE GENERATORIC4601
LCD DRIVERIC4501
VCO
BUF IN15
BUF OUT16
EXT
BGP
14
RGB
BLK
28
FRP
29
SHR
48
SHG
47
SHB
46
SHA
45
+–
15+–
9
SHORTCIRCUIT
PROTECTION
DISCHARGESWITCHQ4601
9
11
13
7
15
17
6
HCK219
HST21
CLR23
EN25
VCK127
VCK229
VST
BLK
HCK1
HCK2
HST
CLR
EN
VCK1
VCK2
VST
BLK
HCK1
HCK2
HST
CLR
EN
VCK1
VCK2
VST
BL_LOW
COM
B
R
G
COM (5.7V)
B
R
G
VF LCDCN BOARD
LCD4701
BACK LIGHTND4701
T4701
EVF_BL_4.95V
FB
DRIVE_PULSE
CN4901
EVF_4.95V (–)
EVF_4.95VEVF_4.95V
VCO
G
FOR JIG
30
18
14
19
18
20
1
21
2
3
4
17
CN4701
11
10
9
12
8
1
25
2
3
4
5
6
7
13
19
21
CN4702
15
14
13
16
12
11
10
9
7
6
5
4
3
1EVF_12V
8
VVDD (12V)
GRT (12V)
4
3
2
1
AGC DET
8
7
6 4
5
10
11
2
12
2.5V REG
OSC
BL BOARD(SEE PAGE 4-97)
05
JTO SYSTEM CONTROL(SEE PAGE 3-16)
CHROMA Y
VIDEO SIGNAL
PB
SIGNAL PATH
500 mVp-p
HREC/PB
208 mVp-p
HREC/PB
2HREC/PB
204 mVp-p
REC/PB
2.16 Vp-p
11 MHz
3.1 Vp-p
VREC/PB H
REC/PB
3.6 Vp-p
H
12 Vp-p
2HREC/PB
8 Vp-p
2H
8 Vp-p
2H
REC/PB
8 Vp-p
3-21 3-22
3-11. EVF BLOCK DIAGRAM
DCM-M1
UPPER CONTROL SW SUB ASSY(SEE PAGE 4-65)
MAIN CONTROL SWITCH UNIT (2/2) (SEE PAGE 4-62)ZOOM SWITCH UNIT(SEE PAGE 4-62)
REMOCON RAY-CATCHERBLOCK UNIT(SEE PAGE 4-65)
MAIN BOARD (7/7)(SEE PAGE 4-29, 48, 56, 59)
LCD BOARD (2/2)(SEE PAGE 4-106)
JACK BOARD(4/4)(SEE PAGE 4-119)
REMOTE TERMINAL UNIT(SEE PAGE 4-119)
LCD DETECTION SW FLEXIBLE BOARD(SEE PAGE 4-65)
LCD OPEN
LCD REVERSEKEY VREC
201
KEY AREC10
KEY PLAY/PAUSE11
8
127
EVER 5V8
PCONT 4
DOUT 10
L DC 14
LOUT 11D IN12
KEY PHOTO
KEY KURU1
KEY KURU2
9
OUT
KEY AD1
143 KEY STOP
188 KEY EJECT
141 OPEN/CLOSE
142 HALF LOCK
202
128
129
130
133135131
ETHER STB
KEY
PLAY
EDI
T
KEY
INTE
RVIE
W
KEY
CAM
ERA
116
LANC OUT 192
TP Y0 120
MULTI_WAKE 187
LANC IN 115
TP X0 119
RMC IN 159
TP IX0 203
KEY AD2
CN8301
S8314 S8311
S8304 S8302 S8301
S8308 S8306 S8303 S8301
S8315
D2.85V
D8301
S8312 S8309
S8307 S8306
A2.85VRV8301
W
T
DSPL
BACK LIGHT
S8308
PHOTO
FOCUSINFINITY
AUDIO REC
S8303
ERASE EXPOSUREMENU
VOL
6
3
5
4
1
CN8303
2
1
7
4
CN8302
2
1
7
4
CN8301 (2/2)
2
8
13
9
10
5
6
7
11
CN8001 (2/2)
1
7
14
10
9
6
5
8
12
CN8002
S8001
S8003
S8002
KEY AD1
KEY AREC
KEY PLAY & PAUSE
KEY STOP
FOCUS
MARK
KEY AD2
KEY PHOTO
KEY KURU1
KEY KURU2
KEY INTERVIEW
KEY PLAY EDIT
KEY VREC
ZOOM SW ZOOM SW AD
KEY CAMERA
PHOTO
ZOOM
A REC LED A REC LED
6
3
5
4
1
ZOOM
3
6
LCD OPEN
LCD REVERSE
LCD OPEN
LCD REVERSE
JOG
CN8021
05
4
1
V REC LED V REC LED
RMC OUTCN1
4
1
CN8003REMOTE CONTROLRECEIVER
IC1
3
6CN8006
S8021
LCD REVERSEDETECT
S8022LCD
OPEN/CLOSEDETECT
S8001, 8003
OPEN/CLOSEDETECT
S8002HALF LOCK
DETECT
D2.85V
D1(CAMERA RECORDING)
2
S8305(START/STOP)
BUFFERQ8006
SWITCHQ8011
TP IY0 206
TP IX1 204
TP IY1 207
LANC WAKE 12
LANC DETECT 140
TP X1 117
TP Y1 118
CN4312 (2/2)
CN4301
TP Y1
TP X1
TP IY1
TP IX1
TP IY0
TP IX0
TP IY1
TOUCHPANEL
TP IX1
TP IY0
TP IX0
TP X0
TP Y0
12
11
9
8
6
7
5
10
CN4302 (2/2)
3
4
6
7
9
8
10
5
IC8015
IC8026
SH3.1V
IC80161
1
24
4
72
1
2
35
6
SYSTEM CONTROLIC8001
LANC DRIVERIC8027
REMOTE
J11
25
27
29
CN3002(4/4)
28
CN8101 (3/3)
25
27
29
4
3
2
CN3003(4/4) CN8004
LANC VCC OUT
LANC DETECT
LANC DATA
LANC VCC OUT
LANC DET
LANC DATA4
3
2
CN11
SWITCHQ4301 (1/2)
SWITCHQ4302 (1/2)
SWITCHQ4301 (2/2)
SWITCHQ4302 (2/2)
SH3.1V
SH3.1V
5
4
2
3
10 TO MPEG ENCODE(SEE PAGE 3-10)
D TO CAMERA CONTROL(SEE PAGE 3-6)
SEL/ PUSH ENTER
S8300
PLAY/EDIT
OFF
CAMERA
INTERVIEW
POWER
3-23 3-24
3-12. MODE CONTROL BLOCK DIAGRAM
DCM-M1
31
1314
78
9
654
7172
77787980
61
62
78
9
10
TPIP
PULSE TRANSFORMERIC8807
CN8802(2/2)
ETHER INTERFACEIC8806
SRAMIC8808
RD+
10BASE-T
ETHER ADAPTER(2/2)
TPIN
TPOPA
IO B
ASE-
T TR
ANSC
EIVE
R
ENCO
DER/
DECO
DER
DETA
LIN
K CO
NTRO
LLER
BUFF
ER M
ANAG
ER
SYST
EM IN
TERF
ACE
TPOPBTPONATPONB
CLKO
CLKI
CE
OEWE
BCS
BOEBWE
34l
4142
l45
•47
l50
•53
56
•58
l60
2l5•8l
17•
28
18l
20•
22l
26
I/O1l
I/O8
A0l
A14
X880120MHZ
BD0 – BD7BD0 – BD7DATA BUS
BA0 – BA14ADDRESS BUS BD0 – BA14
303233
2761
RD–
TD+
TD–
DATA BUS
ADDRESS BUS
18I
23•
25•
27I
29•
85•
87I
91
SD0 – SD15SD8 – SD15
SA0 – SA3
BHE
SA0 – SA34I7
3I
10
14I
21
B0I
B7
A0I
A7
11171582
5436
A2A1A0A3
B2B1B0B3
19202118
923
64
2 22
LEVEL SHIFTIC8801
T/R OE
3I
10
14I
21
B0I
B7
A0I
A7
2 22
LEVEL SHIFTIC8802
T/R OE
7I
10
B4I
B7
A4I
A7
22
LEVEL SHIFTIC8803
LEVEL SHIFTIC8805
CN8801 (2/2)
TO SYSTEM CONTROL(SEE PAGE 3-16)
DO – D15
RD&WT
A0 – A3
SBHE_CE2B
CS6_ETHER
ETHER_INTETHER_WAIT
ETHER_PWR
ETHER_RESET
DQMUL_ICIORDDQMUU_ICIOWR
OE
109
A7A6
B7B6
14
LEVEL SHIFTIC8804
10A7B7
22OE
D8 – D15
D0 – D7 SD0 – SD7
A0 – A314
I17
27282926
21I
24
153334
36
1432
31
1I4•6I9•
11I
13•
15I
19
ECSIOR
READY
HWRST
INT
IOW
K
ETHER BOARD (2/2)(SEE PAGE 4-109)
TO MPEG ENCODE(SEE PAGE 3-10)
G
05
20 MHzREC/PB
1.28 Vp-p
3-25 3-26
3-13. ETHER INTERFACE BLOCK DIAGRAM
DCM-M1
4.95V (CAMERA)
BATTERY TERMINAL POWER BOARD(SEE PAGE 4-130)
VREF
SWITCHING CONTROLIC9001
OUTPUT_6
11INVINPUT_6
10NONINVINPUT_6
51
42
STANDBY3STANDBY
COMPVCC
OUTPUTVCCC_4&5&6
OUTPUTVCC_1&3
OUTPUTVCC_2
63
F9001 L9001
F9002 L9002
F9004 L9005
F9003 L9003
L9004
L9007
CN9002
2
3
1
4
BATT_SIG
AC_DETECT
U_GND
LITIUM BATT_+
BATT_SIG
AC_DETECT_SW
LITIUM_BATT_+(AC_IN_+)
LITIUM_BATT_ –(AC_IN_ –)
13•
28
29•
30
PWMCOMP
OUTPUTCIRCUIT
ERRORAMP
64OUTPUT_5
16INVINPUT_5
15NONINVINPUT_5
PWMCOMP
OUTPUTCIRCUIT
ERRORAMP
19INVINPUT_4
57OUTPUT_4
60MOSGATE_4PWM
COMP
OUTPUTCIRCUIT
ERRORAMP
56OUTPUT_3
PWMCOMP
OUTPUTCIRCUIT
ERRORAMP 33
INVINPUT_3
50OUTPUT_2
46OUTPUT_1
43MOSGATE_1
PWMCOMP
OUTPUTCIRCUIT
ERRORAMP 36
6 4
3
INVINPUT_2
SWITCHINGQ9003
UNREG
39INVINPUT_1
PWMCOMP
OUTPUTCIRCUIT
ERRORAMP
TIMER&
LATCH
OSC
05
27
4
L9013 2.3V
D2.85VL9008SWITCHING
Q9004
SWITCHINGQ9001
L9006SWITCHING
Q9005
SWITCHINGQ9006
L9015
L902
2
L902
1
L9020
L9016 –20V
13V
T9001
12V REGULATORIC9002
4.95V (CAMERA)
IN OUT
FB
4.95V (ETHER)
4.95V (VIDEO)
4.95V (DRIVE)
L9018
L9023
L9017
L9010 D3.1V
SWITCHINGQ9009
SWITCHINGQ9007
–6.5V REGULATORQ9002, 9010
SWITCHINGQ9008
L9009 A2.85V
L9019
1
3
5
48
CN9001
TO MAIN BOARDCN9101 (2/2)(SEE PAGE 3-30)
20
38
4
32
2
6
50•
52
54•
56
30
2.3V
UNREG
DD_CTL
AC_DETECT
BATT_SIG
D2.85V
D2.85V (NF)
A2.85V
A2.85V (NF)
–20V
–6.5V
13V
12V
4.95V (ETHER)
4.95V (VIDEO)
4.95V (DRIVE)
D3.1V
D3.1V (NF)
34•
36
58•
60•
62•
64•
66•
68•
70
40•
42•
44•
46
12•
14•
16•
18
22•
24•
26•
28
8•
10
L
TO MAIN BOARDCN9101 (1/2)(SEE PAGE 3-29)
M
470 kHzREC/PB
2.88 Vp-p
470 kHzREC/PB
5.44 Vp-p
470 kHzREC/PB
940 mVp-p
470 kHzREC/PB
840 mVp-p
470 kHzREC/PB
1.44 Vp-p
470 kHz
REC/PB
800 mVp-p
470 kHzREC/PB
840mVp-p
470 kHz
REC/PB
5.52 Vp-p
3-27 3-28
3-14. POWER 1 BLOCK DIAGRAM
DCM-M1
MAIN BOARD(SEE PAGE 4-29 to 59)
ETHER BOARD (SEE PAGE 4-109) UPPER CONTROLSW SUB ASSY(SEE PAGE 4-65)
REMOCON RAY–CATCHERBLOCK UNIT(SEE PAGE 4-65)
SWITCHQ4003, 4004
MPEG2 RATE CONTROL & SYSTEM CONTROLIC8501
IC8601 IC8101
IC3005IC3009IC5303IC5403IC8020IC8104
IC4001IC4002IC4003IC4004
IC5004IC5005IC5006IC5009
3.1VREGULATOR
IC8202
–15VREGULATOR
Q9102, 9104, 9112
6.5VREGULATOR
Q9101, 9103, 9111
2.8VREGULATOR
IC9103
DC-DC CONVERTERQ5601, 5603
IC5603
SWITCHQ9115, 9116
SWITCHQ9113, 9117
DRIVE CONTROLIC5404
SWITCHQ9105, 9108
SWITCHQ9107, 9110
SWITCHQ5003, 5004
BUFFERQ8009, 8010
SWITCHQ5009, 5010
SWITCHQ5602
SWITCHQ5102
IC5003IC5102
IC5201IC5205
SWITCHQ5001
SWITCHQ5203, 5204
IC5602
IC8027
IC5601
SWITCHQ3003, 3004
IC3001IC3002
C CUT OFF
XLCD
PW
R5LC
D PW
R4LC
D PW
R3LC
D PW
R2LC
D PW
R1EV
F PW
R3EV
F PW
R2EV
F PW
R1
MIC PWR
101
112
SYSTEM CONTROLIC8001
RESETIC8009
MAIN PWR
SDRAM PWR
AC DETECT
DRV PWR
178DD WATCH200
180
151
185199
18694
179
1413121110848586
EVF PWR3
EVF PWR2
EVF PWR1
XLCD PWR5
LCD PWR2
LCD PWR3
LCD PWR1
2.8VREGULATOR
IC9104
IC4006IC4007IC4008IC4009IC4010IC4011
IC8012IC8013IC8602IC8701IC8702IC8703
IC3003IC3004IC3007IC3008IC5002IC5007IC5008IC5013IC5014IC5015
IC5301IC5302IC5401IC5402IC5405IC5406IC5407IC5408IC5501
XSTPON
ADCS
89
DRV REG 16
84
PS A_B 62
LDON
A2.85V
12V
CN8007 CN8801
4.95V (ETHER)
D3.1V
ETHER PWR
CN9101 (1/2)4.95V (ETHER)
4.95V (VIDEO)
12V
–20V
13V
D3.1V (NF)
D3.1V
2.3V
UNREG
D2.85V
D2.85V (NF)
A2.85V (NF)
A2.85V
4.95V (DRIVE)
–6.5V
4.95V(CAMERA)
–20V
13V
D3.1V
2.3V
4.95V (VIDEO)
UNREG
D2.85V
A2.85V
4.95V (DRIVE)
SH 3.1V
IC8023
IC8023
CAM PWR
UNREG WATCH
XCPU PWR
ETHER PWR
4VCC
3OUT
IC8024
IC8023
IC80105 3
4
2
24
1
1
6 2
1
7
2
14
U8001
IC8013
UNREG
SH 3.1V
4.95V (VIDEO)
13V
–20V
12V
4.95V (DRIVE)
14
XMOD 15
INFOBATT SI5
INFOBATT SO29
UNREG MONBA
TT S
IG
AC D
ETEC
T
DD C
TL
CAM
DD
ON
A2.8
5V (C
AMER
A)
A2.8
5V (C
AMER
A)
1.9V
–6.5
V
4.95
V (C
AMER
A)
12V
3
IC8002IC8003IC8005IC8006IC8007IC8014
IC8010IC8023IC8024
IC8004IC8013IC8015IC8016IC8025IC8026
SWITCHQ8007
SWITCHQ8008
SWITCHQ8004
SWITCHQ8003
PROTECTQ9122
3.2VREGULATOR
IC8012,Q8001, 8002
3.2VREGULATOR
IC8011
1.9VREGULATOR
IC9102
UNREG VCCMONITOR
Q9125, 9126
CN4511
EVF A2.85V
EVF D2.85V
EVF 4.95V
EVF 12V
LCD –15V
LCD 6.5V
LCD 13V
LCD 2.85V
LCD 4.95V
SH 3.1V
UNREG
13V
UNREG
MH-V
A2.85V (DRIVE)
4.95V (DRIVE)
LD-VCC
PD-K
MDEN
VCC
CN4313
CN4312
CN5002
CN5001
7
8
9
6
48
12
17
32
17•
18
13•
14
15•
16
47•
49
12•
24
18•
19
9
13•
15
5
4
13
CN9101 (2/2)CN8101
05
13529353739
RMC VCC
D2.85V
D2.85V
D2.85V
D2.85V
CN8002
CN8003
CN8301
CN1
2
3
2
2
34 • 3638 • 40
22 • 24 •
26 • 28
40 • 42 •
44 • 46
58 • 60 •
62 • 64 •
66 • 68 •
70
12 • 14 •
16 • 18
2
38
32
30
8 • 10
34 • 36
50 • 52
4
6
20
48
54 • 56
SH 3
.1V
CN8001
211
IC4005
IC8008
LCD PWR4
40
38 •
39
36
IC8801IC8802IC8803
IC8806IC8808
IC1
40
38 •
39
36
SWITCHQ8801
3
2
IC5010IC5011IC5012
OPTICALPICK-UPBLOCK
19•
20M
TO POWER BOARDCN9001(SEE PAGE 3-28)
NTO VC-216 BOARDCN101(SEE PAGE 3-31) O
TO MAIN CONTROL SWITCH UNITCN8301(SEE PAGE 3-31) L
TO POWER BOARDCN9001(SEE PAGE 3-28)
PTO VF BOARDCN4501(SEE PAGE 3-32)
QTO LCD BOARDCN4302, CN4303(SEE PAGE 3-32)
RTO CLV BOARDCN5803(SEE PAGE 3-32)
IC8804IC8805
3-29 3-30
3-15. POWER 2 BLOCK DIAGRAM
DCM-M1
VF BOARD(SEE PAGE 4-87)
BL BOARD(SEE PAGE 4-97)
IC4502
IC4602
IC4501
IC4601
INVERTER TRANST4701
05
CN4501
CN4901
CN4601 CN4701
CN4702
EVF A2.85V
EVF D2.85V
EVF 12V
EVF 4.95V
EVF 12VGRT (12V)
VVDD (12V)
FOR JIG
EVF BL 4.95V
EVF 4.95V13•
14
9•
10
7•8
2•3
22•
24
2•4
16•
17
26•
27
18
11•
12
SWITCHQ4602, 4603
VF LCDCN BOARD
LCD4701
BACK LIGHTND4701
CLV BOARD(SEE PAGE 4-75)
REC BOARD(SEE PAGE 4-79)
CN5803
CN5801
CN5902
A2.85V (DRIVE)
A2.85VSL
A2.85V
MH-V
4.95V (DRIVE)
MH-V
4.95V
VCC
24
9
13•
15
47•
49
10
8•9
48
12
IC5801IC5803
IC5901
IC5802IC5807IC5851
IC5804IC5805IC5806IC5808
LCD BOARD(SEE PAGE 4-106)
IC4302
IC4301IC4303
IC4304
INVERTER UNITIV4301
CN4303
CN4305
CN4307
CN4306
LCD 6.5V
LCD 4.95V
UNREG
SH 3.1VSH 3.1V
LCD 2.85VLCD –15V
LCD 13V
LCD 4.95V (VSH)
BL HIGH
2.85V (TG) (VDD)
VGL
FOR JIG
VGH
BL
9
6
7
1•2
10
1
2
24
UNREG
13V
UNREG
13V
4.95V
8
CN4302
11
210
LCDPANEL
BACKLIGHT
3
VC-216 BOARD(SEE PAGE 4-13, 17)
IC104
IC202
CN101TO MAIN BOARDCN8101(SEE PAGE 3-29)
CN201
–6.5V
CAM DD ON
12V
1.9V
A2.85V (CAMERA)
4.95V (CAMERA)
MF VCC
SENSE VCCFOCUS/ZOOM
SENSOR
39
38•
40
34•
36
35IC105
IC101
SWITCHQ203
SWITCHQ201
IC001
SWITCHQ103,104
SWITCHQ102
SWITCHQ101
IC002IC102IC103IC201SE001SE201
MFBLOCK
37
29
10
MAIN CONTROLSWITCH UNIT(SEE PAGE 4-62)
ZOOMSWITCH UNIT(SEE PAGE 4-62)
CN8301 CN8302 CN8303A2.85V (CAMERA)
SH 3.1V
VCC-ZOOM12 66
1 SH 3.1V
VCC-ZOOM
CAMERA MICONIC106
LENS RST LED 16
MF LED 17
8
5•
23
N
TO MAIN BOARDCN8001(SEE PAGE 3-29)
O
TO MAIN BOARDCN4511(SEE PAGE 3-30)
P
TO MAIN BOARDCN4312, CN4313(SEE PAGE 3-30)
Q
TO MAIN BOARDCN5002(SEE PAGE 3-30)
R
MOTOR FLEXIBLE BOARD
3-31 3-32 E
3-16. POWER 3 BLOCK DIAGRAM
DCM-M1
4-1 4-2
DCM-M1
(For printed wiring boards)• b: Pattern from the side which enables seeing.
(The other layers’ patterns are not indicated.)• Through hole is omitted.• Circled numbers refer to waveforms.• There are few cases that the part printed on diagram
isn’t mounted in this model.• Chip parts.
• Lead Layouts
When indicating parts by reference number, pleaseinclude the board name.
(For schematic diagrams)• All capacitors are in µF unless otherwise noted. pF : µ
µF. 50 V or less are not indicated except for electrolyticsand tantalums.
• Chip resistors are 1/10 W unless otherwise noted.kΩ=1000 Ω, MΩ=1000 kΩ.
• Caution when replacing chip parts.New parts must be attached after removal of chip.Be careful not to heat the minus side of tantalumcapacitor, Because it is damaged by the heat.
• Some chip part will be indicated as follows.Example C541 L452
22U 10UHTA A 2520
• Constants of resistors, capacitors, ICs and etc with XXindicate that they are not used.In such cases, the unused circuits may be indicated.
• Parts with differ according to the model/destination.Refer to the mount table for each function.
• All variable and adjustable resistors have characteristiccurve B, unless otherwise noted.
• Signal nameXEDIT → EDIT PB/XREC → PB/REC
• 2: non flammable resistor• 1: fusible resistor• C: panel designation• U : B+ Line• V : B– Line• C: adjustment for repair.• Circled numbers refer to waveforms.
Yello
w
A AB BA=B
Fig. a (Video output terminal output waveform)
Fig.b (Picture on monitor TV)
Color bar chartpicture frame
Monitor TVpicture frame
H
Cya
nG
reen
Whi
teM
agen
ta
Red
Blu
e
Yello
wC
yan
Gre
enW
hite
Mag
enta
Red
Blu
e
THIS NOTE IS COMMON FOR WIRING BOARDS AND SCHEMATIC DIAGRAMS(In addition to this, the necessary note is printed in each block)
2 1
3
2 1
3
2 1
3
345
21
123
654
EB
C
31
55
2
46
123
54Transistor Diode
SECTION 4PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS
surface
Lead layout of conventional IC
(Measuring conditions voltage and waveform)MD1 PB :
• Voltages are dc between measurement point.• Readings are taken when playing CD reference disc.
MD2 REC/PB :• Voltages and waveforms are measured between the
measurement points and ground when camera shootscolor bar chart of pattern box. They are reference valuesand reference waveforms.(VOM of DC 10 MΩ input impedance is used)
• Voltage values change depending upon input impedanceof VOM used.)
1. Connection
2. Adjust the distance so that the output waveform of Fig.a and the Fig. b can be obtain.
CSP (chip size package)
Kinds of capacitor
Temperature characteristicsExternal dimensions (mm)
• The voltage and waveform of CSP (chip size package) can-not be measured, because its lead layout is different formthat of conventional IC.
L
Front side of the lens
L = About 90 cm
Pattern box
Note:The components identi-fied by mark 0 or dottedline with mark 0 are criti-cal for safety.Replace only with partnumber specified.
Note:Les composants identifiés parune marque 0 sont critiquespour la sécurité.Ne les remplacer que par unepièce portant le numérospécifié.
DCM-M1
4-5 4-6 4-7 4-8
4-1. FRAME SCHEMATIC DIAGRAM
FRAME
DCM-M1
4-9 4-10 4-11
4-2. PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS
VC-216 (LENS MOTOR DRIVE, CCD IMAGER, CAMERA SIGNAL PROCESS) PRINTED WIRING BOARD– Ref. No.: VC-216 board; 20,000 series –
VC-216 BOARD (SIDE A)
C001 D-7C002 D-7C003 D-6C004 D-7C007 D-7C008 D-8C009 D-7C012 D-8C015 C-8C016 C-8C022 C-8C108 E-5C109 D-5C110 D-6C111 C-5C112 D-5C113 D-5C114 D-5C115 D-5C116 E-5C118 D-5C120 D-5C123 D-4C124 C-4C125 D-4C126 C-4C127 D-4C128 D-4C129 C-3C130 C-3C131 E-3C132 E-3C133 E-3C134 E-3C135 E-3C142 C-4C143 E-3C203 A-8C204 A-8C207 B-8C208 A-8C210 A-8C212 A-8C217 B-8C221 A-6
CN201 A-7
FB103 E-4FB104 E-4FB105 C-3
IC102 D-4IC103 E-4
IC105 D-3IC201 B-8
L001 D-7L101 E-5L103 E-3
Q001 D-7Q101 C-4Q102 C-4Q103 C-4Q104 C-4Q202 A-8Q204 A-8
R005 D-7R007 D-8R009 D-8R010 C-8R011 C-8R015 C-8R107 E-4R115 E-4R116 E-4R118 E-3R119 E-3R123 E-3R135 C-4R138 C-3R203 A-8R206 A-8R208 A-8R209 A-8R210 A-8R211 A-8R213 A-8R215 A-8R218 B-8R219 B-8R220 A-8R221 A-8R222 B-8R224 A-8R225 B-6R226 B-8
SE001 D-8SE201 B-7
LENS MOTOR DRIVE, CCD IMAGER, CAMERA SIGNAL PROCESSVC-216
4-12
VC-216 BOARD (SIDE B)
C010 D-8C011 D-6C013 D-8C014 D-8C017 D-8C018 C-8C019 C-8C020 E-8C021 E-8C023 D-8C024 D-6C101 E-5C102 E-5C103 D-5C104 E-4C105 E-5C106 D-5C107 E-4C117 D-4C119 C-5C121 C-4C136 C-3C137 C-3C138 C-3C139 C-2C140 C-2C141 D-2C201 B-8C202 B-7C205 B-8C206 B-8C209 A-8C211 A-8C213 A-6C214 A-8C215 A-6C216 A-8C218 B-7C219 B-7C220 B-7C222 B-7
CN101 D-1
D101 C-4D201 B-7
FB101 E-4FB102 D-5FB201 A-8
IC002 D-8IC101 D-4IC104 C-4IC106 D-3IC202 A-8
L002 E-6L104 C-4L201 B-6L202 B-7L203 B-6
Q201 A-6Q203 B-7
R008 D-6R012 D-8R013 D-8R014 D-8R016 D-8R101 D-5R102 D-5R103 D-5R104 E-4R105 D-5R106 C-4R108 C-4R109 C-4R110 E-4R111 E-4R112 E-4R113 E-4R117 C-4R120 E-4R121 E-4R122 E-3R124 E-3R125 C-3R126 E-3R127 E-3R128 C-3R129 C-3R130 C-3R131 D-2R132 C-2R133 D-2R134 D-2R136 C-3R137 C-5R201 B-7R202 B-7R205 A-6R207 B-7R212 B-8R214 B-8R216 B-8R217 B-8R223 B-7
X101 C-4X102 E-3
• For Printed Wiring Board.• There are few cases that the part isn't mounted in this model
is printed on this diagram.• Chip transistor
321
45
EB
C
VC-216 boardLENS MOTOR DRIVE,CCD IMAGER,CAMERA SIGNAL PROCESS
REC boardOVER WRITEHEAD DRIVE
CLV board(MD MOTOR DRIVE)
24 1
8
7
14
1
BB
C221
R225
LND201
CN201
R222
R220
R221
R224
R211
R213
R209
R204
C204
Q202
C210
R208
R215 R210
R203C208
C212 C203
R218
R226
R015R011
R010
R007
R009
C012
C008
C002
C001
C123C124
C127
R118R123
R119 L103
C133
C131FB103
C143
C132
C134
C135
R135
Q101Q102
Q103
Q104
C111
C115
IC102
IC103
IC105
C116
C142C129
R138
C130FB105
C122
C120
C118
C112
C114
C109
R115 C1
08
L101
R116
FB10
4 R107
C113
C126C1
28C1
25
C003
R005
C015C016
C009
Q001
C007
C004C110
L001
C022
C217
Q204 R2
06C2
07
R219 LND202
IC201
BB
1
18
5 4
48 3736
2524
1312
75 7651
50
2625 1
100
A
B
C
D
E
1 2 3 4 5 6 7 805
VC-216 BOARD (SIDE A)
IC001 71
14 8
1-673-650-
11
FB20
1
R217
C222
L202
L201
L203
R214
R207
C202
C213
C215
D201
1
15
16
30
IC20
2
C209C211
C205 C201
C206
C019
C018
C014C010
C023
C013 C024
C011
R102
R106R114 R128
R132
R133R134
R131
R130
R137R136
C136C138
C139
C141
C121
R104R110
R111R112
R120
R121
R113 R124R126
R127
X102FB101
C117
D101
C101
C102C104
C107
X101
IC101
IC106
IC104
LND102
LND101
L002
C020
R008 R1
01 R103
R105
R122
R108
R125R1
17
C137
R129
C140
CN10
1
L104
D102
R109
C106
C119
FB10
2
C105 C1
03
C021
R012
R016
R013
C017
R014
IC002
R212R223
R216
C214C216
R202 R201
R205
C220
C218
C219
Q203
Q201
1120
1 10
1001
1
7675
515026
25
48
373625
24
1312
40 3912
A
B
C
D
E
8 7 6 5 4 3 2 105
VC-216 BOARD (SIDE B)
SE001
SE001YAW
SENSOR
SE201(PITCH SENSOR)
1-673-650-
11
3 1
54
DCM-M1
4-13
4-14 4-15 4-16
VC-216 (LENS MOTOR DRIVE, CCD IMAGER) SCHEMATIC DIAGRAM • See page 4-9 for VC-216 printed wiring board. • See page 4-133 for waveforms.
LENS MOTOR DRIVE, CCD IMAGERVC-216 (1/3) VC-216 (2/3)
DCM-M1
4-17 4-18 4-19
VC-216 (CAMERA SIGNAL PROCESS) SCHEMATIC DIAGRAM • See page 4-9 for VC-216 printed wiring board. • See page 4-133 for waveforms.
CAMERA SIGNAL PROCESSVC-216 (3/3)
DCM-M1
DCM-M1
MAIN (AUDIO/VIDEO DATA CONTROL, MPEG ENCODER/DECODER, RF AMP/DRIVE, DIGITAL SIGNAL PROCESSOR,SYSTEM CONTROL, VIDEO, AUDIO, SWITCHING REGULATOR) PRINTED WIRING BOARD– Ref. No.: MAIN board; 10,000 series –
AUDIO/VIDEO DATA CONTROL, MPEG ENCODER/DECODER, RF AMP/DRIVE, DIGITALSIGNAL PROCESSOR, SYSTEM CONTROL, VIDEO, AUDIO, SWITCHING REGULATOR
MAIN
4-21
• For Printed Wiring Board.• There are few cases that the part isn't mounted in this model
is printed on this diagram.• Chip transistor
• Lead Layouts
345
21
EB
C
31
55
2
46
4-23 4-24
MAIN BOARD (SIDE A)
C1003 G-8C1004 G-8C1005 H-8C1006 F-8C1007 F-8C1008 F-8C1009 F-8C1010 F-8C1011 F-8C1012 F-7C1013 G-7C1014 G-7C1015 F-7C1016 G-7C1017 G-6C1018 G-6C1019 G-6C1020 G-5C1021 F-5C1022 G-5C2003 G-8C2004 G-8C2005 H-8C2006 G-8C2007 F-8C2008 F-8C2009 F-8C2010 F-8C2011 F-8C2012 F-7C2013 F-7C2014 G-7C2015 F-7C2016 G-7C2017 G-6C2018 G-6C2019 F-6C2020 G-5C2021 F-5C2022 G-5C3001 G-8C3002 G-8C3003 G-8C3004 F-7C3005 F-8C3006 F-8C3007 H-5C3008 F-5C3011 G-8C3013 G-7C3014 G-7C3015 G-7C3016 G-7C3017 G-8C3018 G-5C3019 G-7C3021 G-6C3022 F-6C3023 F-6C3025 E-6C3026 E-6C3027 F-7C3028 A-6C3030 H-5C3031 F-6C3032 F-6C3033 F-6C3034 F-6C3035 F-6C3036 A-6C3037 A-7C3038 A-7C3039 A-7C3040 A-6C3041 A-7C3042 G-4C3043 F-4C3044 F-5C3045 F-5C3046 F-5C3047 E-6C3049 A-5C3050 G-6C3051 H-6C3053 E-7C3055 F-5C4001 E-5C4002 E-5
C4023 G-4C4024 H-5C4026 G-4C4027 G-4C5001 C-2C5002 B-2C5003 A-1C5004 B-1C5005 A-1C5006 A-2C5007 A-2C5008 B-2C5009 B-1C5011 C-3C5012 C-1C5013 B-2C5014 B-2C5015 B-2C5016 B-2C5017 B-2C5018 A-1C5020 B-1C5021 B-1C5022 B-1C5023 B-1C5024 B-1C5025 B-2C5026 B-1C5027 B-2C5055 B-2C5101 B-3C5102 B-2C5103 B-3C5104 B-3C5105 B-3C5106 B-2C5201 C-3C5202 C-3C5203 C-3C5204 C-3C5205 C-3C5206 D-3C5207 C-3C5208 D-3C5209 D-3C5212 D-3C5301 C-1C5302 D-1C5303 C-1C5304 C-1C5305 C-1C5306 C-2C5307 D-2C5308 C-2C5309 D-2C5310 C-2C5311 D-2C5312 C-2C5313 C-2C5314 C-2C5315 C-2C5316 C-2C5317 C-2C5318 D-2C5319 C-2C5401 G-1C5402 G-1C5403 G-1C5404 F-3C5405 F-2C5406 F-2C5407 G-4C5408 F-2C5409 G-2C5410 F-2C5411 G-2C5412 G-3C5413 F-3C5414 C-3C5415 F-3C5417 D-4C5418 D-4C5420 B-3C5421 D-4C5424 D-4C5501 C-3C5503 E-3C5601 G-1
C5603 E-3C5604 D-3C5605 E-3C5606 D-2C5607 F-2C5608 F-3C5609 D-2C5610 D-2C5614 F-2C8035 B-3C8069 B-4C8070 B-4C8071 G-3C8072 G-3C8073 G-2C8074 G-2C8075 H-2C8076 H-3C8077 G-2C8078 H-2C8079 G-2C8101 D-7C8102 E-5C8103 E-5C8104 E-6C8105 E-6C8106 D-7C8107 E-6C8108 E-6C8109 E-7C8110 E-6C8111 C-6C8112 B-6C8113 B-5C8114 D-7C8115 C-6C8116 C-5C8117 C-5C8118 C-5C8119 D-5C8120 D-5C8121 A-6C8123 E-5C8126 E-6C8127 D-7C8128 A-6C8129 B-5C8130 C-5C8204 B-5C8208 B-5C8211 B-6C9101 A-4C9112 B-7C9113 A-8C9116 A-7C9117 A-4C9118 B-3C9120 A-7C9121 A-7C9122 B-8C9123 A-4C9128 B-8C9129 B-8C9130 B-4C9131 B-4
CN3001 G-8CN3002 H-3CN4312 H-5CN4511 B-8CN5001 A-2CN5002 F-1CN8001 A-5CN8002 C-8CN8003 H-2CN8006 H-6CN8007 B-7CN8101 D-8CN9101 A-4
D4001 H-5D5601 E-3D8005 H-3
FB3001 A-6FB3002 A-6FB8001 B-8FB8002 B-8
FB8003 B-8FB8004 B-8FB8005 B-8FB8006 B-8FB8007 B-8FB8008 C-8FB8009 C-8FB8010 C-8FB8011 C-8FB8012 C-8FB8013 C-8FB8014 C-8FB8015 C-8FB8016 C-8FB8017 C-8FB8018 C-8FB8019 C-7FB8020 C-7FB8021 H-6FB8022 H-6
FL5101 A-2
IC3001 G-8IC3002 F-8IC3004 F-7IC3005 F-7IC3007 F-6IC3008 A-6IC3009 G-4IC4006 G-5IC4007 G-4IC4008 G-4IC5002 B-1IC5003 B-2IC5005 B-2IC5102 B-4IC5201 C-3IC5205 D-3IC5301 C-2IC5302 D-2IC5303 C-3IC5401 G-1IC5403 C-4IC5404 F-3IC5405 G-3IC5406 F-2IC5407 G-4IC5408 F-3IC5501 E-4IC5601 G-2IC5602 E-2IC8026 G-3IC8027 H-3IC8101 D-5IC8102 B-6IC8103 B-5IC8104 E-5IC8202 B-5IC9104 A-7
L3001 F-8L3002 E-6L3003 H-5L3004 A-6L3005 F-5L3006 H-5L4001 E-5L4002 E-5L5001 C-3L5002 B-1L5101 B-3L5301 D-1L5401 D-4L5402 C-3L5403 D-4L5601 E-3L5602 D-3L5603 F-3L5604 F-3L5605 D-2L5606 D-2L5607 D-2L5610 E-1L8003 B-4L8004 B-4L8101 D-7L8102 A-6
L8103 E-6L8104 B-5L8202 B-5L9104 B-8L9105 B-4
Q3004 F-8Q3001 F-8Q3002 E-7Q3003 F-8Q4001 E-6Q4002 E-6Q4005 E-6Q4006 E-6Q4007 F-6Q5001 A-2Q5002 A-2Q5003 B-2Q5004 B-2Q5005 B-2Q5101 B-2Q5102 C-3Q5201 C-3Q5202 C-3Q5203 B-3Q5204 B-3Q5602 G-1Q8006 G-3Q8011 G-3Q9113 B-8Q9115 A-7Q9116 B-7Q9117 A-8Q9125 A-3Q9126 A-3
R1001 G-8R1002 H-8R1003 F-8R1004 F-8R1005 F-8R1006 F-8R1007 F-8R1008 F-8R1009 F-8R1010 F-8R1011 F-8R1012 F-8R1013 F-8R1014 F-8R1015 F-7R1016 G-6R1017 F-7R1019 G-7R1021 G-7R1022 G-6R1023 G-6R1024 G-5R1025 F-5R1026 F-5R1027 G-6R1028 G-6R1029 G-6R1030 G-5R1032 F-8R2001 G-8R2002 H-8R2003 G-8R2004 G-8R2005 F-8R2006 F-8R2007 G-8R2008 F-8R2009 F-8R2010 F-8R2011 F-8R2012 F-8R2013 F-8R2014 F-8R2015 E-7R2016 G-6R2017 F-7R2019 G-7R2021 G-7R2022 G-6R2023 G-6R2024 G-5R2025 F-5
R2026 F-5R2027 G-6R2028 G-6R2029 G-6R2030 G-5R2032 G-8R3001 G-8R3002 F-6R3004 E-8R3005 E-8R3006 F-5R3009 A-7R3010 A-7R3011 A-7R3013 F-8R3014 F-8R3015 F-8R3016 A-7R3018 E-7R3019 E-7R3022 F-5R3023 A-7R4005 E-6R4010 E-6R4013 E-6R4014 E-6R4015 E-6R4016 E-6R4017 E-6R4018 F-6R4021 F-5R4022 F-6R4026 H-5R4030 H-4R5001 A-1R5003 C-2R5004 A-2R5009 B-2R5010 B-2R5011 B-2R5013 B-1R5014 C-1R5015 C-1R5016 B-2R5017 B-2R5018 B-2R5020 B-2R5021 B-2R5022 B-1R5023 B-2R5024 B-1R5025 A-1R5026 B-1R5027 B-1R5028 B-1R5060 B-1R5061 B-1R5101 B-2R5102 B-2R5103 B-2R5104 B-2R5105 B-2R5106 C-3R5107 C-3R5112 B-3R5113 B-3R5201 C-3R5202 C-3R5203 C-3R5204 C-3R5205 C-3R5206 C-3R5207 D-3R5208 C-3R5209 D-3R5210 D-3R5211 D-3R5214 B-3R5215 B-3R5216 D-3R5217 C-3R5301 C-1R5302 C-1R5303 C-2R5304 C-2R5305 C-2R5306 C-2R5307 C-2
R5308 D-3R5309 C-2R5310 D-2R5311 C-2R5312 C-2R5313 D-2R5314 C-2R5316 D-1R5318 D-1R5401 G-1R5402 G-1R5403 F-3R5404 F-3R5405 F-2R5406 F-3R5407 F-2R5408 G-3R5409 F-2R5410 F-2R5411 F-2R5412 F-2R5413 F-4R5414 G-4R5416 D-4R5417 D-4R5418 G-3R5419 D-4R5420 D-4R5421 G-2R5422 G-2R5423 B-4R5424 F-3R5425 D-4R5426 E-2R5427 E-2R5428 E-2R5429 E-2R8063 B-8R8064 B-8R8065 B-8R8066 B-8R8067 B-8R8068 B-8R8069 B-8R8070 C-8R8071 C-8R8072 C-8R8073 C-8R8074 C-8R8075 C-8R8076 C-8R8077 C-8R8078 C-8R8079 C-8R8080 C-8R8081 C-7R8082 C-7R8098 G-2R8101 D-7R8102 E-7R8103 E-7R8104 E-7R8105 E-6R8106 E-7R8107 E-6R8108 E-6R8109 D-6R8110 D-6R8111 C-8R8112 D-6R8113 C-8R8114 D-6R8115 C-8R8116 D-6R8117 C-8R8118 D-6R8119 C-8R8120 D-6R8121 C-8R8122 D-6R8125 D-5R8126 F-5R8127 E-6R8129 D-7R8130 D-7R8208 B-6R8908 G-3R8909 G-2
R8910 H-2R8912 G-3R8915 B-3R8919 A-3R8921 A-6R8931 H-3R8932 H-3R8933 G-3R8934 H-3R8935 G-3R8936 G-3R8937 G-3R9121 A-7R9127 B-7R9128 A-8R9129 B-7R9130 A-4R9132 B-8R9134 B-7R9135 B-7R9136 A-8R9137 A-7R9139 B-7R9143 A-4R9148 A-4R9150 A-3R9153 A-3R9155 A-3R9156 A-3R9904 A-2R9905 B-6R9906 D-7R9910 G-1
X5301 D-1X5401 G-2X5403 D-4
POWER board(DC/DC CONVERTER)
BL board(EVF BACK LIGHT) VF board
(EVF)
MAIN boardAUDIO/VIDEO DATA CONTROL, MPEG ENCODER/DECODER,RF AMP/DRIVE, DIGITAL SIGNAL PROCESSOR,SYSTEM CONTROL, VIDEO, AUDIO, SWITCHING REGULATOR
4-22
surface
Lead layout of conventional IC CSP (chip size package)
R9130
R101
0
R101
2
R201
2R2
009
R200
8
R201
0
R201
4
R101
7
R101
8
R201
7
R201
8
R401
3
R402
2
R402
4
R402
3
R402
1
R202
6R3
022
R102
6
R401
7R4
016
R401
5
R810
5
R810
7R8
108
R810
6
R810
2R3
019
R301
8
R810
3
C810
6C8
114 C8
127
R810
4
R810
1
R811
6R8
118 R8
122
R812
0R8
110
R812
9
R813
0
R811
1
R811
3
R811
7R8
119
C912
8
C911
6
C304
1C3
039
R301
0
R300
9C3
038
C303
7
C911
2
C821
1
C303
6
C304
9
C820
4
C812
9
C806
9
C910
1
C911
7
C911
8C5
103
C510
5
C510
4
Q912
5
Q500
3TP
5001
TP5010 TP5014
Q500
4
C913
0
C913
1
C813
0
R542
3
R914
3
R914
8
R892
0
R891
9R915
6
R915
5
R541
5
C820
8
C811
3
C302
8
L300
4
L820
2
L810
4
L910
5
L810
2
C812
1
C912
1
C912
0
R913
7
R302
3
R820
4
R301
6
R203
1
R103
1
R301
1
R912
9
R912
7
R913
9
R913
5
R913
2
R912
8
C911
3
R913
6
R913
1
C912
9R8
115
R812
1
R810
9C8
111
C812
2
R811
4
R811
2
R812
7R4
014
R100
9
R301
3 R301
4
R301
5
Q300
4
L300
1 R100
8
1
1
4
1
1 345
4
58
11
1
1716
11 4
58
8
5 4
1
1
1 4
58
1
1
1
2
1 345
30
29
141 6
4
58 1 4
58
1 4
58
1 4
58
5 8
14
3619
18
32
7
8
30
3637
48 1612
12
14
13
13
24
24
25
15
IC3001
CN3001
IC3004IC3007
IC8104
IC5501
IC8101
IC8103
IC8202
CN8001CN9101
IC5102
FL5101
CN5001
IC5002
IC8102
IC5205
IC5403
IC5201
IC5003
IC5602
IC5301
IC5005
IC5408
IC5405
1
1 6
7
814
8 9
161
IC8027
IC5601
IC5407
IC8026 IC4006
IC3009IC5404
CN4312
CN3002
CN8003
CN5002
IC4007
IC4008
IC3002IC3005
1
1 2
5049
34
1 234
5
IC5401
IC5406
1 345
1 345
IC5302
IC5303
1169
5 4
1617
98
1
322524
4 5
8
1
1
2 3
270232
133
1
3 4
6
2 20
19
59 60
39
40
26 27
1 2
11
1
8
8
5
5
4
4
6 43
1
1
1
7
2
2
CN8101
CN8007
IC9104
Q9115
IC3008
CN8002
CN4511
R991
0
R542
1R5
422
R890
9
R809
8 R893
6 R893
3R8
912
R541
4
R540
8R5
418
R540
3
R540
6
R540
4
R541
1
R540
7
R540
5
R541
2
R542
4
R541
3
R893
4 R893
2
R891
0
R893
1
C807
6
C560
1
C807
3
C807
7
C541
2C5
404
C541
3
C560
8D5
601
C560
7
L560
3
C541
5
C807
1 C540
7
C304
2
C302
9
C303
0
C305
1
D990
4
R990
9R1
029R2
028
R202
9
R102
8
R102
2
R202
0
R102
0
R200
3R1
014
R203
2
R200
2
R303
0
R100
2
R101
9
R201
9
R102
3
R102
7R2
027
R202
3
C301
8
C101
8
C305
0
C101
9
C101
7
C201
7
C201
4
C301
9 C301
2C301
3
C301
5
C101
4
C101
6
C100
5C1
002
C200
2C301
6
C301
4
C200
3
C100
6
C201
1C2
010C1
015
C201
5
C302
5
C302
6C3
023
C302
1
C302
2
C303
3
C303
2
C303
4
C305
5
C400
1
C400
2
C811
0
C810
9C810
7C8
108
C202
0C3
046
C304
4
C303
5
C303
1R3
007
C300
5
R100
3R1
004
C101
0
C101
1
C100
3
L300
3
L300
6
CN8006
FB8021
C2018
FB8022
C402
7
C807
5
X540
1C541
0
L5610
R531
8
R531
7
R531
6
R531
5
R531
0
L560
7
L500
1
L540
2
L540
1
L540
3
L400
1
L400
2
L560
6
L560
5
L560
2
L560
8C530
9
C561
0
C560
9
C531
8
C560
6
C541
6C521
2C5
208
C520
9R5
211
R530
8
R531
2R5
311
R530
4
R510
6
R520
1 R520
4
R521
5
R521
4
R511
2
R511
3
C531
2C5
306
R530
9C5
316
C531
0
C520
3
C520
2
C541
4C530
8
C510
7
C501
1
Q510
2
R530
6R5
303
C502
5
C521
0
C501
4
C501
0
C505
5
C502
7
C500
9
C502
3
C530
1
C500
1
C500
8
C500
2
C502
4
C500
4
C500
5
C500
3
R510
2
R510
1
R500
4
R501
4
R501
5
R530
1
R506
0
R510
3R5
010
R502
0
R502
1
R501
6
R501
7
R501
8R5
003
R501
1
R510
4
R521
3R5
209
R521
0
R531
3
R520
7R5
208
R521
6R5
217
R521
2
C560
4
C531
9
C520
6C5
207
C541
7C5
418
C811
8C8
119
C812
0
R812
5
C531
5
C560
3
C550
3
C530
7C5
409
C807
9
D800
5C807
8
Q5602
C5403 C5401
C5408
C5405
C5406
C5614
C5411
C8074
L5604
L5601
C5605
C5611
C5311
C5313
Q5202Q5201
X5403
C5314
R5307
Q5204
Q5203
Q5005
R5205
R5202R5203
R5206
R5420 R5419 R5425 R5416
R8124
R5417
R5107
C5205 C5204
C5423
C5422
C5424
C8123
C8102 C8103 C8104 C8105
R9906
R8081
R8082R8080
L9104
Q9117
Q9116
Q9113
R8079
R8078
R8077
R8076
R8075
R8074
R8073
R8072
C9122
R8071
R8070
R8069
R8068
R8067
R8066
R8065
R8064
R8063
R9134R9905
R8208
R8921
R8922
C8112
C8128
C8070
R9150
R5111
R9904
R5105
R9153
R5009
R5029
R5027
R5061
R5023
R5002
R5019
R5025
R5028
R5022
R5024
R5026
R5001
TP5002
R5013
C5007
C5018
C5006
C5013
C5016
C5015
C5017
C5020C5021
C5012
C5022
C5026
C5305
C5304
C5303
R5302
L5002
Q9126
Q5001
Q5101
Q5002
C9123
C8035
C5106
C5102
L8003
L5101
L8004
FB3002
TP8047
FB3001
C3040 R9122
R9121
FB8018
FB8017
FB8016
FB8015
FB8014
FB8013
FB8012
FB8011
FB8010
FB8009
FB8008
FB8007
FB8006
FB8005
FB8004
FB8003
FB8002
FB8001
FB8019
FB8020
D9903C5421
C5201
C5101 C5420
C5501
R5305
TP5015
C5317
R5319
R5314
TP5401 TP5403
TP5424
TP5404
TP5422TP5421
TP5408
TP5407
TP5409
TP5423
R8935
R8908 C8072
R8937
R4030 R4027 R4026
R2024 R1030
R1024
R1016 R2016
C2016
C2004C3001
C1004
C3003
C3011
C1007
C1009C2009
C2012
C3010
C3053
C3009
C3004
C2013
C1008
C3006
C3017
C3002
C1012
C3027
C3020
C2019 C2006
C2008
C2007
C1013
R2004
R1021
R1015
R2021
R2001
R2006
R1006
R2011
R3004R2015
R3002R1025
L3005
Q4001
R3006
R2025
R2030
L3002
L8103
C3024
C3047
C8126
C8101
C8115C8116C8117
L8101
C1021
C3045
C3043
C3008
C2021
C2022
C1022
Q4006
Q4005
Q3002
Q4002
Q4007 D3009
R2022
R4018R8126 R8123
R4010
R4005
R8128
C3048 R3005
R1013
R2013
R1011
Q3003
Q3001
R1005
R1032
R1007
R3001
R2005
R2007
R1001
C2005
C4025 C4024
C1020
C3007
C4026 C4023
D4002 D4001
Q8011
Q8006
C5402
R5402R5401
R5410
R5428
C5302
X5301
L5301
R5426R5429
R5427
R5409
D8004
12 113
2425 36
37
48
5 4
31
A
B
C
D
E
F
G
H
1 2 3 4 5 6 7 805
MAIN BOARD (SIDE A)
1-672-520-
11
DCM-M1
4-25 4-26
DCM-M1
AUDIO/VIDEO DATA CONTROL, MPEG ENCODER/DECODER, RF AMP/DRIVE, DIGITALSIGNAL PROCESSOR, SYSTEM CONTROL, VIDEO, AUDIO, SWITCHING REGULATOR
MAIN
4-27
MAIN BOARD (SIDE B)
C3048 E-8C3052 G-6C4003 G-1C4004 G-2C4005 G-2C4006 G-2C4007 G-3C4008 G-3C4009 G-3C4010 H-2C4011 H-3C4012 H-2C4013 H-2C4014 H-3C4015 H-3C4017 H-2C4018 H-2C4019 H-1C4020 G-1C4021 G-2C4022 G-1C4028 C-8C4029 B-8C4031 A-8C4032 A-8C5019 B-1C5028 B-1C5029 B-1C5030 B-1C5031 C-1C5032 C-1C5033 C-1C5034 A-1C5035 C-2C5036 C-2C5037 C-2C5038 C-2C5039 B-2C5040 C-2C5041 B-2C5042 B-2C5043 B-1C5044 B-1C5045 B-2C5046 B-2C5047 B-1C5048 B-1C5049 C-1C5051 E-2C5052 E-1C5056 B-1C5057 A-1C5419 F-3C5602 F-2C5615 F-3C8001 D-6C8002 C-6C8003 D-6C8004 C-6C8005 C-6C8006 C-6C8007 C-6C8008 C-6C8009 B-5C8010 B-5C8011 B-5C8012 B-4C8013 B-4C8014 C-4C8015 C-4C8016 C-3C8017 C-3C8018 C-4C8019 C-4C8020 C-4C8021 D-4C8022 C-3C8023 D-5C8024 D-5C8025 D-5C8026 D-5C8027 D-5C8028 D-5C8029 D-5C8030 D-5C8031 D-5C8032 A-3C8033 A-3
C8034 B-5C8036 B-3C8037 D-6C8038 B-3C8039 C-6C8040 C-6C8041 C-6C8042 C-6C8043 B-6C8044 C-6C8045 B-6C8046 A-4C8047 A-4C8048 A-4C8049 A-6C8050 A-4C8051 B-4C8052 A-4C8053 A-4C8055 B-3C8056 B-3C8057 B-4C8059 B-4C8062 A-3C8063 D-4C8064 D-6C8065 B-3C8067 D-6C8068 D-4C8080 B-3C8081 A-3C8501 E-3C8502 E-3C8503 D-2C8504 E-3C8506 C-2C8507 E-3C8508 D-2C8510 E-2C8511 D-3C8601 F-6C8602 F-6C8603 G-4C8604 G-4C8605 F-4C8606 F-5C8607 F-5C8608 F-5C8609 F-5C8610 F-7C8611 F-5C8612 F-6C8613 G-6C8614 G-6C8615 G-5C8616 G-5C8617 G-5C8618 G-5C8619 E-4C8620 G-4C8621 G-3C8622 E-3C8623 E-3C8624 F-3C8701 E-7C8702 F-5C8703 F-5C8704 E-4C8705 E-4C8706 E-4C8707 E-6C8708 E-6C8709 E-6C8710 D-6C8711 E-6C8712 E-6C8713 E-6C8714 E-6C8715 E-6C8716 E-6C8717 E-7C8718 F-6C9103 H-5C9104 H-5C9105 H-6C9106 G-5C9107 H-5C9108 H-4
C9109 G-5C9110 H-5C9111 G-6C9114 H-4C9115 H-5C9119 H-6C9126 C-8C9127 C-8C9132 C-8C9133 C-8
CN4313 H-4
D4003 B-8D5602 E-1D8001 D-5D8002 B-2D8003 B-3D8006 C-3D8007 A-3
FL4001 G-3FL4002 H-3
IC3003 G-6IC4001 G-2IC4002 G-2IC4003 H-2IC4004 H-3IC4005 H-2IC4009 B-8IC4010 A-8IC4011 A-8IC5004 C-2IC5006 B-1IC5007 B-1IC5008 C-1IC5009 C-2IC5010 C-2IC5011 B-2IC5012 B-2IC5013 C-1IC5014 E-2IC5015 E-1IC5402 F-3IC5603 F-2IC8001 C-5IC8002 C-6IC8003 B-6IC8004 B-5IC8005 A-5IC8006 A-4IC8007 A-4IC8008 D-4IC8009 D-5IC8010 D-5IC8011 A-3IC8012 B-3IC8013 A-4IC8015 B-4IC8016 B-4IC8020 A-3IC8023 D-5IC8024 D-5IC8025 B-3IC8501 D-3IC8601 F-5IC8602 F-4IC8701 E-5IC8702 E-6IC8703 E-6IC9102 C-8IC9103 G-5
L4003 G-1L8001 D-5L8002 D-3L8501 E-2L8601 G-7L8602 F-6L8603 F-3L8701 F-6L8702 F-7L9102 G-5L9103 G-6
Q4003 H-1Q4004 H-1
Q5009 A-2Q5010 B-2Q5601 E-2Q5603 F-3Q8001 B-3Q8002 B-2Q8003 C-3Q8004 C-2Q8005 D-4Q8007 A-3Q8008 A-3Q8009 B-3Q8010 B-3Q8012 B-6Q8013 A-6Q8014 B-6Q9101 H-5Q9102 H-6Q9103 H-5Q9104 H-6Q9105 H-4Q9107 H-5Q9108 G-4Q9110 H-6Q9111 H-5Q9112 G-6Q9122 D-8
R4001 G-2R4002 G-2R4003 G-3R4004 G-3R4006 H-3R4007 H-3R4008 H-3R4009 H-3R4011 H-1R4012 H-1R4019 H-3R4020 H-3R4028 B-8R4031 A-7R5005 B-1R5006 B-1R5007 B-1R5008 B-1R5012 B-1R5030 C-1R5031 C-2R5032 B-1R5033 A-1R5034 B-1R5037 C-2R5038 C-2R5039 C-2R5040 C-2R5041 C-2R5042 C-2R5043 C-2R5044 C-2R5045 C-2R5046 C-2R5047 C-2R5048 C-2R5049 B-2R5050 B-2R5051 C-2R5052 B-2R5053 B-2R5054 B-1R5055 B-2R5056 B-2R5057 B-1R5058 E-2R5059 E-2R5076 B-2R5077 B-2R5078 A-2R5601 F-2R5602 F-2R5603 F-2R5604 F-2R5605 F-3R5606 F-3R5607 E-2R8001 D-6R8002 D-6R8003 D-6
R8004 D-6R8005 D-7R8006 D-6R8007 D-6R8008 D-7R8009 D-6R8010 D-6R8011 D-6R8012 C-3R8013 C-3R8015 B-4R8016 B-4R8017 C-4R8018 C-4R8019 C-4R8020 C-4R8021 C-4R8022 B-4R8023 B-4R8024 C-4R8025 C-4R8026 C-3R8027 C-3R8028 B-3R8029 C-3R8030 C-4R8031 C-4R8032 C-3R8033 C-3R8034 C-4R8035 C-4R8036 B-7R8037 C-4R8038 D-5R8039 B-4R8040 B-3R8041 D-5R8042 D-5R8043 D-5R8044 D-5R8045 D-5R8046 C-7R8047 D-5R8048 B-3R8049 B-3R8050 B-2R8051 B-3R8052 B-2R8053 B-4R8055 B-3R8056 B-3R8057 B-4R8058 B-4R8061 A-2R8062 B-7R8083 D-5R8084 A-4R8085 B-7R8086 B-7R8087 B-7R8088 D-4R8089 D-5R8090 D-5R8091 B-7R8092 C-7R8093 D-5R8094 D-5R8095 D-5R8096 D-5R8097 B-3R8099 D-6R8501 D-2R8502 D-2R8503 D-2R8504 D-2R8505 D-2R8506 D-2R8507 D-2R8508 D-2R8509 D-2R8510 D-2R8511 D-3R8512 E-4R8513 E-4R8514 E-4R8515 E-4R8516 E-4R8517 E-4
R8519 E-4R8520 C-3R8521 D-2R8522 D-2R8523 D-2R8524 D-3R8525 E-4R8526 E-4R8527 E-4R8528 E-4R8529 D-3R8530 E-2R8531 D-3R8532 E-3R8601 F-5R8602 F-5R8603 F-4R8901 B-4R8902 B-6R8903 B-6R8904 D-6R8906 C-4R8911 C-3R8913 D-5R8914 C-3R8916 B-3R8917 A-3R8918 A-3R9101 H-6R9102 H-6R9103 H-6R9104 H-6R9105 H-5R9106 G-5R9107 H-4R9108 G-4R9109 H-4R9110 H-5R9111 H-6R9112 H-6R9113 G-4R9114 H-6R9116 H-6R9117 H-5R9118 G-5R9119 G-5R9120 G-4R9123 H-5R9124 H-6R9125 G-6R9126 G-4R9140 C-8R9144 H-6R9147 G-6R9152 C-8R9154 G-5R9157 H-5R9159 C-8R9161 C-8R9901 A-2R9902 B-7R9903 D-6
S8001 D-1S8002 E-1S8003 G-4
U8001 D-4
X8001 D-4X8002 D-6X8003 C-4X8501 D-3
TP5018
TP5013
TP5012
TP5011
TP9114
TP9110
TP9103
TP9109
TP9104
TP9111TP9106
TP9105
TP8042
TP9107
TP9108
TP5016
C5057
R5008R5007R5032
C502
8
C505
6
C501
9
C5108
R5109R5108
Q5010R5035
R5036R5110
R5053 R5054
C5044C5041
C5042 C502
9C5
031
C505
0
C851
2
C850
3C8
508
C503
5
C808
0
L800
2
C802
0
C802
5
C802
6
C802
7C802
8
X800
3
Q800
5
C806
8C802
3
C802
4
C800
2C8
005
C800
6C8
007
C800
8
C804
3C8
049
R890
3R8
902
C806
6
C803
0
X800
1
D800
6
C850
6
C503
3C5
049
S8001
U8001
S8002
C503
0R5
034
R990
1
R500
6
R507
6
R507
7R805
6R8
055
R805
1
C803
6 C505
4
C808
2
R507
8
R805
0
Q800
2
Q800
1
Q800
9
C808
1
C805
7
TP80
44
C805
3
C804
8C8
052
C805
0
C805
5
C801
9R8
907
R804
7
R808
3
R804
1
R803
8
R804
3R8
042
R804
4
R800
6C8
710
C871
1
C870
1
L870
2
IC3003
L870
1
L910
3
C305
2
C910
9
C910
4
R910
5
R911
9
C910
6
C862
0
C400
9
C400
8 C400
5
C402
1
R401
2
R401
1
C402
2
C402
0
C400
3
L400
3
C401
0
C401
8
C401
1
IC4004
IC4002 IC4001
C401
4
C400
7
C862
1
C400
6
C401
6
R400
9
R400
4
R400
3
S8003 FL4001
C860
3C8
604
C860
5
C911
5
C911
4
R914
7
R915
4R9
106
R911
7R9
118
R910
9R9
115 R9
107
C910
8R9
126
R910
8
R911
3
R912
0
R910
1
R911
6
R911
2
R912
4
C910
5
C910
2
R910
4
R910
3
R910
2
R911
4
R912
5
L860
1
C871
4C8
715
R800
7R8
009
R800
4
R800
1
R800
3
R800
5
R800
2
R801
0
R800
8
R801
1
R891
3
R890
6
TP8045
C801
4C8
013
C805
6R8
917
R805
8
R891
8R808
4
R805
4
IC80
11
R805
2
R891
6
D800
2
R500
5
R503
0
R505
1
R504
8R5
043
R503
1R5
042
R851
0
IC5015
R8504
TP8502
S8001
TP8503TP8501
R8505
R8502
R8501
R8503
R8506
R8507
R8521
R5607
R5605
R5606
C5615
C8623
C8507R8532R8515
R8512R8527
R8525
R8519
R8603
R8526
R8517
R8516
R8514
R8513
R8528
C8624
C5419TP5417
TP5414
TP5402
Q5601
Q5603
L8603
D5602
TP5405
R5058
R5059
C5051
C5052
R850
9
R850
8
R852
3
R852
2
R853
0C8
510
C560
2
C850
1
C850
2
C862
2
C870
5
C861
9
C860
6
C860
7
C861
1
C870
9C8
708
C870
7
C870
2
C860
9
C860
8
C870
3
R860
2
R860
1
C870
4
C870
6
C850
4
R853
1R8
524
C561
3
R560
2
R560
3
R560
4
R560
1
L850
1
R504
0
R503
9R5
037
R503
8
R504
1
R891
4
R504
4
R504
6
R504
5
R504
7
D500
1
R501
2
IC5006
IC5007
C5032
IC5008
TP5003C5043
C5048
R5057
R5050R5049
R5055
R5056
R5052
C5047
C5046
C5045
C5036
C5037
IC5009
C5040C5038
C5039
C5034R5033
R8061
Q5009
5
5
4
4
1
1
8
8
54 1
8
IC5013
18 5
4
IC8501
IC8004
IC8001
IC8002
X8002
IC8003
IC8005
32
17
1
16
Q8007
C8033
C8062
C8047C8046
C8054
D8003
C8032
C8038
R8915TP8018
C8065
C8016C8017C8018C8015
R8040
R8097R8022R8015R8053
R8034
R8088
R8090
R8089
R8045
R8093
R8096R8095D8001
R8094
R8099
L8001
R8905R8904
R9903
TP8020
C8029
C8004
C8012C8011C8010C8009C8034
C8045
Q8012
Q8013
Q8014
TP8019
TP8039
TP8043
TP8021
TP8024
TP8022
TP8040
TP8031
TP8023
TP8032 TP8025
TP8012
TP8034
TP8015
TP8017
TP8035
TP8009TP8013
TP8027TP8026
TP8028
TP8029 TP8109
TP8107
TP8106
TP8108
TP8601
TP1002
TP2002
TP8101
TP8102
TP8103
TP8111
TP8110TP8113
TP8114TP9112
TP9116
TP8007
TP8008
TP8006
TP8005
TP8001TP8003
TP8002
TP8004
TP8104
TP8105
TP9115
TP8112
TP8033
TP8036
TP8011
TP8010
TP8016
TP8014
TP8038
TP807
TP8030
TP8041
TP9102
TP3002
TP3001
D9901
R9902
R4031C4032C4031
C4030
C4029
C4028 C9132
C9133
Q9122
C9127
D4004
D4003
R8036
R8046
R8092
R914
0R9
152
R915
8R9
160
R915
9
R916
1
C912
6
R8086
R8091
R8062
R8085
R8087
R4029
R4028
TP9101
C8031
C8003
C8039C8040
C8041C8044C8042
C8001
C8712
C8713
C8718
C8610
L8602
L9102
C8602
C8601
C8612
C8613
C8614
C9111
TP9113
C8615 C8616
C9107
C8617 C8618
C9103
C9119
C9110
R9111
Q9112
Q9103
Q9107
Q9111 Q9108
R4019R4008
R4007
R4006
R4002
R9908
TP4003
R4001
C4015
C4012
C4004
C4019
Q4003
Q4004
TP4001
C4017
C4013IC4003
R4020
TP1001
TP2001
TP4002
FL4002
Q9105Q9101
R9144R9157
R9123
R9110
Q9104 Q9110
Q9102
C8716C8717
C8067
C8064
C8037
R8018
R8017
TP8046R8016
R8037
R8021
R8031
R8025
R8023
R8019
R8020
R8030
R8024
R8028
R8029
R8013
R8033
R8027
R8048
R8057
R8049
IC8012
Q8008
Q8010
IC8025
IC8016
IC8013
IC8007 IC8006
IC8014 D8007
IC8015
C8059R8039
C8051
R8901
8
8
5
5
5
44
4
1
1
IC8020
1
1
14 8
8
7
IC5004
Q8004
R8520
C8505
C8063C8021
C8022
C8511
R8529R8511
R8911
R8012
R8032
R8026
R8035
TP8504
TP8505
X8501
IC5010
IC5012
IC5011
Q8003
14
8 7
1
11
4
4
558
8
IC8008
IC8010IC8009
U8001
5
1 10
6
IC8023
IC8024
IC8601
IC8701
IC8602
IC8702
IC8703
18 5
4
1 86
4443
IC5014
IC5402
IC5603
4
1 8
5
IC4011
18 5
4IC4010
18 5
4
IC4009
IC9102
1
1 346
8 54
IC9103
CN4313
4
3 1
6
IC4005
5
4 1
8
1
1
1
1
5
5
5
5
4
4
4
4
3
3
3
3
15 4
3
15 4
3
15 4
315 4
3
15 4
3
154
3
1 345
5
1
1
23
3
4
4
1
4 5
8
1 14 1
34
6
1
34
6 1
34
6
1 346
1 5
54
3 1
43
K
A
1 345
4
5 1
3
5 4
31
OPEN/CLOSEDETECT
S8002HALF LOCK
DETECT
S8003OPEN/CLOSE
DETECT
(LITHIUM SECONDARY BATTERY)
A
B
C
D
E
F
G
H
8 7 6 5 4 3 2 105
MAIN BOARD (SIDE B)
1-672-520- 11
DCM-M1 MAIN (AUDIO/VIDEO DATA CONTROL) SCHEMATIC DIAGRAM • See page 4-21 for MAIN printed wiring board. • See page 4-133 for waveforms.
AUDIO/VIDEO DATA CONTROLMAIN (1/8)
4-29
4-30 4-31 4-32
DCM-M1
4-37
4-36MPEG ENCODER/DECODER
MAIN (2/8)
MAIN (MPEG ENCODER/DECODER) SCHEMATIC DIAGRAM • See page 4-21 for MAIN printed wiring board. • See page 4-133 for waveforms.
4-33 4-34 4-35
DCM-M1
4-39 4-40 4-41 4-42
MAIN (RF AMP/DRIVE) SCHEMATIC DIAGRAM • See page 4-21 for MAIN printed wiring board. • See page 4-134 for waveforms.
DCM-M1
RF AMP/DRIVEMAIN (3/8)
DCM-M1MAIN (DIGITAL SIGNAL PROCESSOR) SCHEMATIC DIAGRAM • See page 4-21 for MAIN printed wiring board. • See page 4-134 for waveforms.
4-43 4-44 4-45
DCM-M1
DIGITAL SIGNAL PROCESSORMAIN (4/8)
4-46
DCM-M1
SYSTEM CONTROLMAIN (5/8)
4-48
4-49 4-50 4-51 4-52
MAIN (SYSTEM CONTROL) SCHEMATIC DIAGRAM • See page 4-21 for MAIN printed wiring board. • See page 4-133 for waveforms.
DCM-M1
4-554-53 4-54VIDEO
MAIN (6/8)
MAIN (VIDEO) SCHEMATIC DIAGRAM • See page 4-21 for MAIN printed wiring board. • See pages 4-133, 134 for waveforms.
DCM-M1
4-56 4-57AUDIO
MAIN (7/8) 4-58
MAIN (AUDIO) SCHEMATIC DIAGRAM • See page 4-21 for MAIN printed wiring board. • See page 4-134 for waveforms.
DCM-M1
4-614-59 4-60SWITCHING REGULATOR
MAIN (8/8)
MAIN (SWITCHING REGULATOR) SCHEMATIC DIAGRAM • See page 4-21 for MAIN printed wiring board. • See page 4-133 for waveforms.
DCM-M1
4-62
4-63MAIN CONTROL SWITCH UNIT, ZOOM SWITCH UNIT
4-64
MAIN CONTROL SWITCH UNIT, ZOOM SWITCH UNIT SCHEMATIC DIAGRAM
DCM-M1
4-65 4-66
4-67
UPPER CONTROL SW SUB ASSY, REMOCON RAY-CATCHERBLOCK UNIT, LCD DETECTION SW FLEXIBLE BOARD
UPPER CONTROL SW SUB ASSY, REMOCON RAY-CATCHER BLOCK UNIT,LCD DETECTION SW FLEXIBLE BOARD SCHEMATIC DIAGRAM
DCM-M1
4-68 4-69 4-70
CLV (MD MOTOR DRIVE) PRINTED WIRING BOARD– Ref. No.: CLV board; 20,000 series –
CLV BOARD (SIDE A)
C5807 C-11C5808 C-11C5811 B-9C5813 B-5C5814 A-6C5815 B-8C5818 B-7C5819 B-11C5823 C-9C5825 B-9
IC5802 B-10IC5804 B-6IC5805 B-8IC5806 B-6IC5807 C-11IC5808 B-7
Q5821 C-9Q5823 B-9
R5802 C-11R5803 C-11R5806 B-10R5807 B-10R5809 C-10R5810 C-10R5823 C-11R5824 C-11R5826 C-9R5828 B-9
S5801 A-5S5802 A-6S5803 A-6S5804 A-9
MD MOTOR DRIVECLV
DCM-M1
4-744-71 4-72 4-73
CLV BOARD (SIDE B)
C5804 A-10C5805 A-9C5806 B-10C5809 C-9C5810 C-10C5812 C-10C5816 A-8C5817 B-8C5820 A-9C5824 C-8C5826 C-9C5827 B-9C5828 B-9C5829 A-6C5851 D-6C5852 C-7C5853 D-7C5854 D-7
CN5801 C-11CN5803 B-1
D5801 C-7
IC5801 B-10IC5802IC5803 C-10IC5851 D-7
L5801 B-6
Q5801 B-7Q5802 A-8Q5803 A-9Q5808 D-8Q5809 C-8Q5810 C-8Q5811 C-8Q5812 B-8Q5813 B-8Q5822 C-9Q5824 C-9Q5825 B-9Q5826 B-9
R5801 A-10R5804 A-9R5805 C-10R5808 C-9R5811 A-8R5812 A-9R5813 C-8R5814 C-8R5815 C-8R5816 C-9R5817 B-8R5818 B-8R5819 A-9R5820 B-7R5821 A-8R5822 A-8R5825 E-12R5827 D-8R5829 C-8R5830 B-9R5831 B-8R5832 B-10R5833 B-10R5834 C-10R5851 D-6R5852 D-7
S5805 E-11
SE5851 D-6
• For Printed Wiring Board.• There are few cases that the part isn't mounted in this model
is printed on this diagram.• Chip transistor
VC-216 boardLENS MOTOR DRIVE,CCD IMAGER,CAMERA SIGNAL PROCESS
REC boardOVER WRITEHEAD DRIVE
CLV board(MD MOTOR DRIVE)
123
654
EB
C
MD MOTOR DRIVECLV
DCM-M1
4-75 4-76 4-77 4-78
CLV (MD MOTOR DRIVE) SCHEMATIC DIAGRAM • See page 4-68 for CLV printed wiring board. • See page 4-134 for waveforms.
MD MOTOR DRIVECLV
DCM-M1
4-824-79 4-80 4-81
• For Printed Wiring Board.• There are few cases that the part isn't mounted in this model
is printed on this diagram.• Chip transistor
VC-216 boardLENS MOTOR DRIVE,CCD IMAGER,CAMERA SIGNAL PROCESS
REC boardOVER WRITEHEAD DRIVE
CLV board(MD MOTOR DRIVE)
OVER WRITE HEAD DRIVEREC
REC (OVER WRITE HEAD DRIVE) PRINTED WIRING BOARD AND SCHEMATIC DIAGRAM– Ref. No.: REC board; 20,000 series –
EB
C
DCM-M1
VF (EVF) PRINTED WIRING BOARD– Ref. No.: VF board; 20,000 series –
• For Printed Wiring Board.• There are few cases that the part isn't mounted in this model
is printed on this diagram.• Chip transistor
POWER board(DC/DC CONVERTER)
BL board(EVF BACK LIGHT) VF board
(EVF)
MAIN boardAUDIO/VIDEO DATA CONTROL, MPEG ENCODER/DECODER,RF AMP/DRIVE, DIGITAL SIGNAL PROCESSOR,SYSTEM CONTROL, VIDEO, AUDIO, SWITCHING REGULATOR
VF BOARD (SIDE A)
C4502 F-4C4503 F-3C4504 E-1C4505 E-1C4506 F-1C4507 F-1C4508 F-2C4510 H-4C4512 F-1C4514 G-1C4516 H-3C4517 H-3C4518 H-3C4519 H-2C4520 G-1C4521 H-4C4522 G-4C4523 H-1C4524 H-2C4526 E-4C4527 E-4C4612 A-4C4618 C-2C4620 B-2C4624 A-3C4625 A-1
IC4501 G-3IC4602 A-2
L4501 H-5L4502 F-3
Q4502 F-1Q4503 F-1Q4504 F-1Q4505 G-1Q4506 G-1Q4507 H-1
R4501 E-2R4516 F-2R4517 F-2R4518 G-5R4525 F-4R4528 F-4R4530 G-4R4531 G-4R4540 G-4R4564 G-2R4565 G-4R4566 G-4R4567 G-4R4568 G-5R4604 B-4R4607 B-5R4615 A-4R4617 A-4R4618 B-4R4629 B-1R4630 C-2R4634 C-2
4-83 4-84 4-85 4-86EVF
VF
EB
C
VF BOARD (SIDE B)
C4501 F-3C4509 F-1C4515 G-1C4525 H-1C4601 C-5C4602 C-5C4603 C-4C4604 C-4C4605 A-5C4606 C-4C4608 C-4C4610 B-4C4611 B-4C4613 A-4C4614 C-4C4615 C-4C4616 C-1C4617 C-2C4619 B-3C4621 B-2C4622 C-3
CN4501 F-4CN4601 A-2CN4901 H-7
D4601 A-3D4602 C-2
IC4502 G-4IC4601 B-4
L4503 F-4L4601 B-3L4602 B-3L4603 B-1
Q4601 C-5Q4602 A-3Q4603 A-3
R4502 F-4R4503 F-3R4507 F-4R4508 F-3R4514 E-1R4515 E-1R4519 F-1R4520 F-1R4523 F-1R4524 F-1R4526 G-3R4527 G-2R4529 F-1R4532 G-3R4533 F-1R4534 F-1R4535 G-1R4538 F-1R4539 G-1R4541 G-3R4542 H-3R4543 G-3R4544 G-1R4546 H-3R4547 H-3R4550 G-2R4551 G-2R4553 G-1R4556 G-3R4557 G-1R4558 G-1R4559 G-1R4560 G-1R4561 G-1R4562 H-2R4570 G-1R4601 C-3R4602 C-3R4603 B-4R4605 B-4R4608 B-4R4609 B-4R4610 A-4R4611 A-4R4612 A-4R4613 B-4R4614 B-4R4616 B-4R4619 C-4R4620 C-4R4621 B-4R4622 A-3R4623 C-4R4624 B-2R4626 C-3R4627 C-1R4628 C-2R4636 B-3
DCM-M1
4-91
4-90EVF LCD DRIVE, EVF TIMING GENERATOR
VF
VF (EVF LCD DRIVE, EVF TIMING GENERATOR) SCHEMATIC DIAGRAM • See pages 4-133, 134, 135 for waveforms.
4-87 4-88 4-89
DCM-M1
4-93 4-94 4-95 4-96
DCM-M1
EVF BACK LIGHTBL
BL (EVF BACK LIGHT) PRINTED WIRING BOARD– Ref. No.: BL board; 20,000 series –
• For Printed Wiring Board.• There are few cases that the part isn't mounted in this model
is printed on this diagram.• Chip transistor
POWER board(DC/DC CONVERTER)
BL board(EVF BACK LIGHT) VF board
(EVF)
MAIN boardAUDIO/VIDEO DATA CONTROL, MPEG ENCODER/DECODER,RF AMP/DRIVE, DIGITAL SIGNAL PROCESSOR,SYSTEM CONTROL, VIDEO, AUDIO, SWITCHING REGULATOR
EB
C
DCM-M1
4-97 4-98 4-99
4-100
BL (EVF BACK LIGHT DRIVE, EVF BACK LIGHT) SCHEMATIC DIAGRAM
EVF BACK LIGHT DRIVE, EVF BACK LIGHTBL
Note:The components identi-fied by mark 0 or dottedline with mark 0 are criti-cal for safety.Replace only with partnumber specified.
Note:Les composants identifiés parune marque 0 sont critiquespour la sécurité.Ne les remplacer que par unepièce portant le numérospécifié.
DCM-M1
4-101 4-102 4-103 4-104LCDLCD
LCD (LCD) PRINTED WIRING BOARD– Ref. No.: LCD board; 20,000 series – • For Printed Wiring Board.
• There are few cases that the part isn't mounted in this modelis printed on this diagram.
• Chip transistor
EB
C
DCM-M1
4-1084-105 4-106 4-107LCDLCD
LCD BOARD (SIDE B)
C4301 D-9C4302 D-10C4303 D-10C4304 G-10C4305 F-7C4306 E-8C4307 G-9C4308 F-5C4309 G-8C4310 H-8C4311 H-8C4312 F-9C4313 G-8C4314 H-7C4315 F-8C4316 G-8C4317 G-5C4318 H-6C4319 D-10C4320 B-3C4321 B-4C4322 G-7C4323 H-7C4324 G-7C4325 G-5C4326 G-6C4327 A-4C4328 C-2C4329 D-3C4330 D-3C4331 D-2C4332 B-4C4334 B-4C4335 B-4C4336 C-3C4337 B-4C4338 B-2C4339 C-4C4340 D-4C4341 C-5C4342 D-3C4344 A-3C4345 D-8C4346 A-4C4352 D-9
CN4301 A-5CN4302 C-11CN4303 F-11CN4305 F-1CN4306 A-3CN4307 A-8
D4302 D-2D4303 B-4D4304 D-4
FB4301 A-4
IC4301 E-9IC4302 F-7IC4303 C-3IC4304 C-4
L4301 E-10L4302 E-10L4303 E-8L4305 G-6L4306 B-4L4307 C-2L4308 B-3L4309 B-2
Q4301 E-4Q4302 E-3Q4303 G-9Q4304 G-8Q4305 H-8Q4306 H-9Q4307 G-8Q4308 H-7Q4312 D-3Q4313 D-4
R4301 F-9R4302 G-8R4303 G-9R4304 G-9R4305 G-9R4309 E-4R4310 F-6R4313 G-9R4314 H-8R4315 H-8R4316 H-8R4317 F-7R4318 F-6R4319 F-8R4320 F-8R4321 H-8R4322 G-8R4323 F-6R4324 F-6R4325 F-6R4326 F-6R4327 F-6R4328 G-9R4329 F-6R4330 F-6R4331 F-9R4334 F-9R4335 H-7R4336 G-7
R4337 G-8R4338 E-3R4339 H-7R4340 G-8R4343 G-8R4344 H-7R4345 F-8R4347 F-8R4350 G-6R4351 G-7R4353 F-8R4354 D-3R4356 D-2R4357 D-3R4358 C-3R4359 B-5R4360 B-5R4362 D-3R4366 C-2R4369 B-4R4370 C-4R4371 C-4R4372 C-4R4373 C-4R4374 C-4R4375 C-4R4376 C-4R4377 C-4R4378 C-4R4379 C-5R4380 C-5R4381 C-5R4382 D-3R4383 C-4R4384 E-4R4385 E-3R4386 C-5R4387 G-2R4388 F-2R4389 F-2R4390 F-2R4391 A-5R4392 F-2R4393 D-10R4394 E-10R4395 D-11R4396 D-11R4397 E-7R4400 B-2R4401 C-4R4402 B-5R4403 F-6R4405 F-9R4407 H-7R4408 D-8R4409 E-8
LCD (LCD) SCHEMATIC DIAGRAM • See page 4-135 for waveforms.
JACK board(AV IN/OUT)
ETHER board(ETHER INTERFACE)
LCD board(LCD)
Note:The components identi-fied by mark 0 or dottedline with mark 0 are criti-cal for safety.Replace only with partnumber specified.
Note:Les composants identifiés parune marque 0 sont critiquespour la sécurité.Ne les remplacer que par unepièce por tant le numérospécifié.
DCM-M1
ETHER (ETHER INTERFACE) PRINTED WIRING BOARD– Ref. No.: ETHER board; 20,000 series –
• For Printed Wiring Board.• There are few cases that the part isn't mounted in this model
is printed on this diagram.• Chip transistor
4-109 4-110 4-111 4-112ETHER INTERFACE
ETHER
EB
C
JACK board(AV IN/OUT)
ETHER board(ETHER INTERFACE)
LCD board(LCD)
DCM-M1
4-1154-113 4-114ETHER INTERFACE
ETHER
DCM-M1
4-116 4-117ETHER INTERFACE
ETHER 4-118
ETHER (ETHER INTERFACE) SCHEMATIC DIAGRAM • See page 4-109 for printed wiring board. • See page 4-135 for waveforms.
DCM-M1
4-119 4-120AV IN/OUT
JACK
JACK (AV IN/OUT) SCHEMATIC DIAGRAM • See page 4-121 for printed wiring board.
DCM-M1
4-121
JACK (AV IN/OUT) PRINTED WIRING BOARD– Ref. No.: JACK board; 20,000 series –
4-122AV IN/OUT
JACK
DCM-M1
4-123 4-124AV IN/OUT
JACK
• For Printed Wiring Board.• There are few cases that the part isn't mounted in this model
is printed on this diagram.
JACK board(AV IN/OUT)
ETHER board(ETHER INTERFACE)
LCD board(LCD)
DCM-M1
4-125
POWER (DC/DC CONVERTER) PRINTED WIRING BOARD– Ref. No.: POWER board; 20,000 series –
4-126DC/DC CONVERTER
POWER
POWER BOARD(SIDE A)
C9001 A-10C9002 A-10C9003 A-10C9004 C-9C9009 C-8C9011 C-8C9015 C-6C9052 A-9C9055 C-5C9057 C-5C9061 C-5C9063 C-5C9064 C-1C9065 C-4C9068 C-1C9076 C-4C9080 C-5
CN9001 G-1
D9001 A-10D9002 C-9D9003 C-9D9011 A-10D9012 B-1
F9001 C-10F9002 B-10
FB9001 A-10FB9002 A-9
L9001 C-9L9002 B-9L9003 C-7L9004 B-8L9005 B-7L9006 C-6L9007 B-6L9008 B-3L9009 B-5L9010 B-2L9013 A-5L9015 B-1L9017 C-5L9018 C-4L9019 C-5L9023 C-4
R9060 C-2R9062 B-5R9064 C-3R9066 B-3R9067 A-4R9068 C-2
T9001 B-1
DCM-M1
4-1294-127 4-128
• For Printed Wiring Board.• There are few cases that the part isn't mounted in this model
is printed on this diagram.• Chip transistor
DC/DC CONVERTERPOWER
123
654
EB
C
POWER board(DC/DC CONVERTER)
BL board(EVF BACK LIGHT) VF board
(EVF)
MAIN boardAUDIO/VIDEO DATA CONTROL, MPEG ENCODER/DECODER,RF AMP/DRIVE, DIGITAL SIGNAL PROCESSOR,SYSTEM CONTROL, VIDEO, AUDIO, SWITCHING REGULATOR
DCM-M1
4-130 4-131DC/DC CONVERTER
POWER 4-132
POWER (DC/DC CONVERTER) SCHEMATIC DIAGRAM • See page 4-125 for printed wiring board. • See page 4-135 for waveforms.
Note:The components identi-fied by mark 0 or dottedline with mark 0 are criti-cal for safety.Replace only with partnumber specified.
Note:Les composants identifiés parune marque 0 sont critiquespour la sécurité.Ne les remplacer que par unepièce por tant le numérospécifié.
4-133
DCM-M1
4-3. WAVEFORMS
REC/PB
2.24 Vp-p
6
REC/PBH
H
7 Vp-p
1
REC/PB
7 Vp-p
2
H
36 MHz
REC/PB
1 Vp-p
3
18 MHz
REC/PB
3.28 Vp-p
4
16.33 MHz
18 MHz
REC/PB
3.12 Vp-p
5
REC/PB
3.84 Vp-p
7
HREC/PB
3.04 Vp-p
8
VREC/PB
2.88 Vp-p
9
VREC/PB
2.88 Vp-p
0
2VREC/PB
2.96 Vp-p
qa
13.5 MHz
REC/PB
Approx.3.4 Vp-p
qs
20 MHz
REC/PB
1.22 Vp-p
qd
32.768 kHz
REC/PB
408 mVp-p
qf
9.8304 MHz
REC/PB
1.1 Vp-p
qg
32.768 kHz
REC/PB
1.5 Vp-p
qh
27 MHz
REC/PB
3.52 Vp-p
qj
H
REC/PB
700 mVp-p
qk
H
H
REC/PB
360 mVp-p
3.1 Vp-p
ql
REC/PB
1.12 Vp-p
w;
VREC/PB
wa
H
REC/PB
3.6 Vp-p
ws
6.6 MHz
REC/PB
1.12 Vp-p
wd
H
REC/PB
2.32 Vp-p
wf
H
H
H
REC/PB
2.04 Vp-p
wg
REC/PB
1.48 Vp-p
wh
REC/PB
1.1 Vp-p
wj
4-134
DCM-M1
PB (MD2)
REC/PBH
H
680 mVp-p
REC/PB
368 mVp-p
200 ns
100 ns
PB (MD1)
Approx.712 mVp-p
Approx.280 mVp-p
PB
Approx.1.54 Vp-p: MD1Approx.1.86 Vp-p: MD2
PB
200 ns: MD1100 ns: MD2
200 ns: MD1100 ns: MD2
Approx.1.22 Vp-p: MD1Approx.880 mVp-p: MD2
200 nsPB (MD1)
Approx.324 mVp-p
100 nsPB (MD2)
Approx.360 mVp-p
200 ns
PB (MD1)
Approx.200 mVp-p
22.5792 MHzREC/PB
980 mVp-p
22.5792 MHzREC/PB
3.4 Vp-p
70.54 MHzREC/PB
320 mVp-p
16.934 MHzREC/PB
1.58 Vp-p
11.2896 MHz
44.1 kHz
2..8224 MHz
REC/PB
3.84 Vp-p
REC/PB
4.24 Vp-p
Approx.12 ms: MD1Approx.7.5 ms: MD2
Approx.23.6 ms: MD1 Approx.14.8 ms: MD2
REC/PB
3 Vp-p
REC/PB
4.32 Vp-p
Approx.1.38 Vp-p: MD1Approx.1.68 Vp-p: MD2
Approx.560 mVp-p: MD1Approx.780 mVp-p: MD2
REC/PB
Approx.1 Vp-p: MD1Approx.1.32 Vp-p: MD2
500 mVp-p
208 mVp-p
Approx.23.6 ms: MD1Approx.14.8 ms: MD2
REC/PB
Approx.23.6 ms: MD1Approx.14.8 ms: MD2
REC/PB
HREC/PB
H
REC/PB
2H
2H
REC/PB
REC/PB
204 mVp-p
2H
2H
REC/PB
8 Vp-p
REC/PB
8 Vp-p
8 Vp-p
H
REC/PB
12 Vp-p
wk ej
ek
el
r;
ra
rs
rd
rf
rg
rh
rj
rk
rl
t;
ta
ts
td
tf
ef
eg
eh
wl
e;
ea
es
ed
4-135
DCM-M1
REC/PB
REC/PB
H
2.16 Vp-p
REC/PB
560 mVp-p
H
H
2H
2H
2H
2H
REC/PB
220mVp-p
4 Vp-p
REC/PB
1.26 Vp-p
REC/PB
3.12 Vp-p
REC/PB
236 mVp-p
REC/PB
4 Vp-p
REC/PB
4 Vp-p
20 MHz11 MHz
REC/PB
1.28 Vp-p
15.4 MHz
tg yf
470 kHz
REC/PB
800 mVp-p
yg
470 kHz
REC/PB
5.52 Vp-p
yh
470 kHzREC/PB
940 mVp-p
yj
470 kHzREC/PB
840 mVp-p
yk
470 kHzREC/PB
1.44 Vp-p
yl
470 kHzREC/PB
2.88 Vp-p
u;
470 kHzREC/PB
5.44 Vp-p
ua
470 kHzREC/PB
840mVp-p
us
ya
ys
yd
th
tj
tk
tl
y;
4-135E
5-1
SECTION 5EXPLODED VIEWS
DCM-M1
• Items marked “*” are not stocked since theyare seldom required for routine service. Somedelay should be anticipated when orderingthese items.
• The mechanical parts with no reference num-ber in the exploded views are not supplied.
• Hardware (# mark) list and accessories andpacking materials are given in the last of theelectrical parts list.
NOTE:• -XX and -X mean standardized parts, so they
may have some difference from the originalone.
• Color Indication of Appearance PartsExample:KNOB, BALANCE (WHITE) . . . (RED)
↑ ↑Parts Color Cabinet's Color
Les composants identifiés par unemarque 0 sont critiquens pour lasécurité.Ne les remplacer que par une pièceportant le numéro spécifié.
The components identified bymark 0 or dotted line with mark0 are critical for safety.Replace only with part numberspecified.
Ref. No. Part No. Description RemarkRef. No. Part No. Description Remark
5-1. MAIN SECTION
13
12
11
1029
7
6
4
58
cabinet (R) section
14
2
15
16
15#1
17
2
2
1
3
18
2
1
19
20
1 4-223-679-23 SCREW (2.0), MI (M2.0X4.5)2 4-223-676-15 SCREW (1.7), MI (M1.7X3)3 3-977-650-01 SCREW, TRIPOD4 4-218-461-11 SCREW (M1.7)5 4-216-024-01 COVER, JACK
6 4-216-022-01 BRACKET, BELT7 4-216-023-01 SHAFT (BELT FRONT)8 4-218-462-01 BELT, GRIP9 4-221-110-01 BRACKET10 4-216-036-01 BRACKET (REAR), BELT
11 4-216-049-01 SHAFT (BRACKET REAR)12 4-219-035-01 SCREW13 X-4951-294-1 CAP ASSY, LENS14 1-418-201-21 SWITCH UNIT, MAIN CONTROL15 4-223-676-23 SCREW (1.7), MI (M1.7X4)
16 4-223-676-31 SCREW (1.7), MI (M1.7X4.5)17 4-220-888-01 BRACKET (SHOE)18 X-4950-890-1 PEN ASSY, TOUCH19 1-418-732-21 REMOTE COMMANDER (RMT-DCM1)20 3-742-854-01 LID, BATTERY (for RMT-DCM1)
5-2
5-2. CABINET (R) SECTION
Ref. No. Part No. Description RemarkRef. No. Part No. Description Remark
67
6869
70
71
72 73
51
51
not supplied
not supplied
not supplied
78
59
77
63
59
59
6465
66
62
6151
60
5851
57
51
56
55
54
5251
53
77
74
74
#2
7681
77
74
807975
#2
82
83
51 4-218-461-01 SCREW (M1.7)52 A-3321-881-A POWER BOARD, COMPLETE
* 53 4-216-028-01 CASE (REAR), SHIELD54 3-043-103-01 CUSHION (SHIELD)
* 55 4-216-027-01 CASE (FRONT), SHIELD
56 1-672-513-11 TRANSLATION FLEXIBLE (JACK) BOARD57 A-3321-883-A JACK BOARD, COMPLETE58 4-216-025-01 BRACKET (JACK)59 4-224-946-01 SPACER (JACK)60 4-224-945-01 SPACER (REMOTE TERMINAL)
61 1-418-563-11 TERMINAL UNIT, REMOTE* 62 4-220-720-01 MATERIAL, ACOUSTIC ISOLATION (M)
63 4-216-021-01 BRACKET (FRONT), BELT64 4-223-676-15 SCREW (1.7), MI (M1.7X3)65 4-225-467-01 SEAL (JACK. ENGLISH)
66 3-043-483-01 SHEET (GRIP RUBBER), ADHESIVE67 3-043-015-01 RUBBER, GRIP
68 3-043-016-01 RUBBER, GRIP69 1-418-202-21 SWITCH UNIT, ZOOM70 X-3378-880-1 CABINET (R) SUB ASSY71 4-216-052-01 BLIND (EVF), ADJUSTMENT72 4-984-017-21 SCREW (1.7), TAPPING
73 4-215-993-01 SHEET, BT74 3-713-791-01 SCREW (M1.7X5), TAPPING, P275 X-4950-899-1 CASE ASSY, BATTERY76 3-972-819-01 SPRING, BATTERY77 4-223-676-23 SCREW (1.7), MI (M1.7X4)
78 1-694-497-11 TERMINAL BOARD, BATTERY79 4-219-034-01 SHEET, INSULATING80 4-215-995-01 BRACKET (ETHER PC BOARD)81 A-3323-174-A ETHER BOARD, COMPLETE82 3-043-261-01 SHEET, COPY
83 3-044-616-01 SHEET, SHIELD
5-3
5-3. MICROPHONE BLOCK SECTION
Ref. No. Part No. Description RemarkRef. No. Part No. Description Remark
108
109
113
110111
105
114111
101
102
#3
LCD block section
103
102104
117
115 116
107106
124
116
#2
123
cabinet (L) section
120
122119
116
118
not supplied
112
121
101 4-216-044-01 COVER (FRONT), HINGE102 4-223-676-15 SCREW (1.7), MI (M1.7X3)
* 103 4-220-721-01 MATERIAL, ACOUSTIC ISOLATION (S)104 4-216-045-01 COVER (REAR), HINGE
* 105 4-220-719-01 MATERIAL, ACOUSTIC ISOLATION (L)
106 X-4950-891-1 PLATE ASSY, BLIND107 4-223-676-09 SCREW (1.7), MI (M1.7X2.5)108 X-4950-897-1 BASE ASSY, MICROPHONE109 4-216-018-01 RUBBER, MICROPHONE110 1-418-564-11 RAY-CATCHER BLOCK UNIT, REMOCON
111 4-984-017-21 SCREW (1.7), TAPPING112 1-418-192-11 MICROPHONE UNIT
113 4-220-639-01 ABSORBENT (GEL), ACOUSTIC114 4-216-019-01 COVER, BASE115 3-043-171-01 SHEET (MICROPHONE)116 4-218-461-01 SCREW (M1.7)117 4-220-640-01 ABSORBENT (SHEET), ACOUSTIC
118 3-713-791-01 SCREW (M1.7X5), TAPPING, P2119 3-335-797-01 SCREW (M1.4X2), TOOTHED LOCK120 A-3323-422-A MAIN BOARD, COMPLETE121 3-044-612-01 SHEET, SHIELD (IC3009)122 1-672-514-11 TRANSLATION FLEXIBLE BOARD
123 4-215-975-21 CUSHION (PANEL)124 3-043-102-01 FOOT (L), RUBBER
5-4
5-4. CABINET (L) SECTION
Ref. No. Part No. Description RemarkRef. No. Part No. Description Remark
167
155
166
168
165CT-DCMM1-164
164
164
163
161162
157158
159
160
156
155
154
153
152
151
152
152
154
MT-DCMM1-163
173
168160
172
171EVF block section
170
169
151 X-3378-420-1 PANEL ASSY, UPPER152 4-218-229-19 SCREW (1.4), MI (M1.4X2)153 3-320-382-11 FOOT, RUBBER154 4-218-458-01 DAMPER (MD)155 4-223-676-15 SCREW (1.7), MI (M1.7X3)
156 X-3378-881-1 CABINET (FRONT) ASSY157 X-4950-893-1 CHASSIS (F) ASSY158 4-995-402-01 SPRING (LOCK), TENSION159 3-914-116-01 SPRING (R), TENSION160 4-215-976-01 SCREW (DAMPER)
161 4-215-989-21 CUSHION (MD)162 X-4950-894-1 CHASSIS (M) ASSY
163 3-837-971-01 CUSHION164 4-215-989-01 CUSHION (MD)165 4-218-461-01 SCREW (M1.7)166 4-220-349-01 CUSHION (CAMERA)167 4-216-053-01 CUSHION (CABINET)
168 4-223-676-09 SCREW (1.7), MI (M1.7X2.5)169 X-3378-951-1 CONTROL SW SUB ASSY, UPPER170 X-4950-892-1 BUTTON ASSY, AUDIO CONTROL171 4-223-676-23 SCREW (1.7), MI (M1.7X4)172 4-221-112-01 SHAFT
173 3-842-935-01 CUSHION
5-5
5-5. LCD BLOCK SECTION
Ref. No. Part No. Description RemarkRef. No. Part No. Description Remark
208 209
207
223206
205
203
201
202 212
204
211
210
205
215
205
214
218
216
217
219220
213
221
222LCD4301
224
201 X-3378-952-1 CABINET ASSY (U), LCD202 4-216-051-01 BLIND (LCD), ADJUSTMENT203 4-223-676-15 SCREW (1.7), MI (M1.7X3)
* 204 4-216-034-01 FRAME, LCD205 4-223-676-09 SCREW (1.7), MI (M1.7X2.5)
206 4-218-461-01 SCREW (M1.7)207 1-959-252-11 HARNESS (GLAY)208 1-959-251-11 HARNESS (YELLOW)209 4-220-687-01 TAPE (LCD), HARNESS BLIND210 A-3323-169-A LCD BOARD, COMPLETE
211 4-220-440-01 SHEET (LCD), SHIELD212 4-926-578-01 PLATE (P), RUBBER
0213 1-517-843-11 FLUORESCENT TUBE
214 X-4950-896-1 HINGE ASSY215 1-672-355-11 LCD DETECTION SW FLEXIBLE BOARD216 4-223-676-07 SCREW (1.7), MI (M1.7X2)217 4-216-041-01 CABINET (O), LCD218 3-051-046-01 SLEEVE, HARNESS
219 4-216-047-01 SPRING (LOCK), TORSION220 4-216-043-01 LOCK, LCD221 1-803-445-11 PANEL, TOUCH222 4-218-463-01 SPACER (LCD)223 3-042-678-01 SHEET (LCD), ELECTROSTATIC
224 3-042-688-01 SHEET (LCD FLEXIBLE RETAINER)LCD4301 1-803-033-21 INDICATOR MODULE, LIQUID CRYSTAL
The components identified bymark 0 or dotted line withmark 0 are critical for safety.Replace only with part num-ber specified.
Les composants identifiés par unemarque 0 sont critiques pour lasécurité.Ne les remplacer que par une pièceportant le numéro spécifié.
5-6
5-6. EVF BLOCK SECTION
Ref. No. Part No. Description RemarkRef. No. Part No. Description Remark
251
252
253254
253
LCD4701
263
255
267
266
265
264
263
262
261
260
257
258259
256
251 1-672-356-11 VF/LCD FLEXIBLE BOARD252 A-3321-877-A BL BORAD, COMPLETE253 3-989-416-01 CUSHION (458), LCD254 3-988-563-01 ILLUMINATOR (458), BL255 3-960-302-11 CUSHION (1), LCD
256 X-3948-473-1 LENS ASSY (458), VF257 4-216-042-01 CABINET (UPPER), EVF258 3-988-565-01 SHEET, VF COVER ADHESIVE259 3-988-564-01 COVER, VF
260 4-216-039-01 CUP, EYE261 4-218-460-01 ARM, VISIBILITY ADJUSTMENT262 4-216-040-01 CABINET (LOWER), EVF263 3-713-791-01 SCREW (M1.7X5), TAPPING, P2264 3-950-044-01 RING, O
265 4-218-459-01 KNOB, VISIBILITY ADJUSTMENT266 A-3321-879-A VF BORAD, COMPLETE267 1-672-357-11 VF FLEXIBLE BOARDLCD4701 8-753-023-89 LCX024AK-5
5-7
5-7. LENS BLOCK SECTION(CT-DCMM1-164)
Ref. No. Part No. Description RemarkRef. No. Part No. Description Remark
305306
307
302
308
302
309 310310
311not supplied(IC001)
304
303
302
301
notsupplied
301 A-3250-920-A CT-DCMM1-164302 3-713-791-01 SCREW (M1.7X4), TAPPING, P2
* 303 4-215-973-01 BRACKET, LENS FRAME304 8-848-732-01 DEVICE, LENS (LSV-620B)305 3-963-467-11 ADAPTOR (FH), CCD FITTING
306 1-758-202-21 FILTER BLOCK, OPTICAL
307 3-961-192-01 RUBBER (FH), SEAL* 308 4-215-974-01 BRACKET, LENS BLOCK
309 4-215-989-21 CUSHION (MD)310 3-335-797-01 SCREW (M1.4X2), TOOTHED LOCK311 3-318-203-11 SCREW (B1.7X6), TAPPING
5-8
5-8. MECHANISM DECK SECTION-1(MT-DCMM1-163)
Ref. No. Part No. Description RemarkRef. No. Part No. Description Remark
351 3-349-825-41 SCREW352 A-3321-863-A REC BOARD, COMPLETE353 X-4951-230-1 HOLDER ASSY354 4-217-955-01 SPRING (POWER TENSION), TENSION355 4-963-883-41 SCREW (M1.4), PRECISION PAN
356 4-217-946-01 GUIDE, HOLDER357 3-315-414-41 WASHER358 4-217-950-01 GEAR, WORM359 4-217-957-01 SPRING (WORM GEAR), COIL360 4-996-249-01 SCREW (M1.2X1.2)
361 4-217-944-01 GEAR (STEPPER)
362 4-217-948-01 GEAR (WORM WHEEL)363 X-4951-231-1 HOLDER (STEPPER) ASSY364 3-338-645-31 WASHER (0.8-2.5)365 4-963-883-01 SCREW (M1.4), PRECISION PAN366 4-217-958-01 SHEET, ADHESIVE
367 A-3323-163-A CLV BOARD, COMPLETE* 368 4-217-952-01 SHIELD (A)* 369 4-217-953-01 SHIELD (B)
370 4-963-883-21 SCREW (M1.4), PRECISION PANM5811 1-698-543-21 MOTOR (STEPPING)
370
366
369
368
364365
367
362
361
360359
358
357
M5811
363
356
355
354
353352 351
5-9
5-9. MECHANISM DECK SECTION-2(MT-DCMM1-163)
Ref. No. Part No. Description RemarkRef. No. Part No. Description Remark
401 X-4952-432-1 SERVICE ASSY, OP402 4-963-883-21 SCREW (M1.4), PRECISION PAN403 X-4951-229-1 CHASSIS ASSY404 4-995-585-01 SPRING (LIMITTER), TORSION405 4-963-897-01 HOLDER (GUIDE SHAFT)
* 406 4-217-956-01 SHAFT (SUB GUIDE)407 3-704-197-33 SCREW (M1.4X3.0), LOCKING408 1-675-950-11 MOTOR FLEXIBLE BOARD409 1-418-191-11 SENSOR, MR410 4-217-928-01 GEAR (A)
411 4-217-954-01 SCREW (M1.4X4), TAPPING* 412 4-217-943-01 BRACKET, MOTOR
413 3-704-246-01 SCREW (P 1.4X1.6)414 4-217-941-01 BRACKET (LEAD SCREW)
* 415 4-217-949-01 SHAFT (MAIN GUIDE)416 4-217-927-01 GEAR (B)417 1-452-997-11 ENCODER, MAGNET
* 418 4-217-942-01 SCREW, LEAD419 4-963-883-81 SCREW (M1.4), PRECISION PAN420 4-963-883-41 SCREW (M1.4), PRECISION PAN421 4-217-947-01 SPRING, THRUST422 4-955-841-11 SCREW
423 4-217-951-01 COVER, MD
416417
418
419
409411
410
412413
414
not supplied(M5801)
408
407
405
406
405
415
401
404
403402
not supplied(M5821)
not supplied
423not supplied(HR5901)
420421
422
5-9 E
6-1
SECTION 6ELECTRICAL PARTS LIST
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
BL CLV
NOTE:• Due to standardization, replacements in the
parts list may be different from the parts speci-fied in the diagrams or the components usedon the set.
• -XX and -X mean standardized parts, so theymay have some difference from the originalone.
• RESISTORSAll resistors are in ohms.METAL: Metal-film resistor.METAL OXIDE: Metal oxide-film resistor.F: nonflammable
• Items marked “*” are not stocked since theyare seldom required for routine service.Some delay should be anticipated when order-ing these items.
• SEMICONDUCTORSIn each case, u: µ, for example:uA. . : µA. . uPA. . : µPA. .uPB. . : µPB. . uPC. . : µPC. .uPD. . : µPD. .
• CAPACITORSuF: µF
• COILSuH: µH
A-3321-877-A BL BOARD, COMPLETE*******************
(Ref. No.: 20,000 Series)
< CAPACITOR >
C4701 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25VC4702 1-113-642-11 TANTALUM CHIP 47uF 20% 10VC4703 1-115-566-11 CERAMIC CHIP 4.7uF 10% 10VC4704 1-164-677-11 CERAMIC CHIP 0.033uF 10% 16V
0C4706 1-115-464-91 CERAMIC CHIP 0.0022uF 10% 630V
< CONNECTOR >
CN4701 1-784-421-11 CONNECTOR, FFC/FPC (ZIF) 27PCN4702 1-691-354-21 CONNECTOR, FFC/FPC (ZIF) 16P
< DIODE >
0D4701 8-719-056-49 DIODE 1SS370 (TE85L)
< COIL >
L4701 1-410-389-31 INDUCTOR CHIP 47uHL4702 1-414-398-11 INDUCTOR 10uH
< FLUORESCENT INDICATOR >
0ND4701 1-517-758-11 TUBE, FLUORESCENT (0.55 INCH)
<TRANSISTOR >
0Q4701 8-729-039-24 TRANSISTOR FX216-TL1
< RESISTOR >
R4701 1-218-883-11 METAL CHIP 33K 0.5% 1/16WR4702 1-216-809-11 METAL CHIP 100 5% 1/16W
< TRANSFORMER >
0T4701 1-426-848-51 TRANSFORMER, INVERTER************************************************************
A-3323-163-A CLV BOARD, COMPLETE*********************
(Ref. No.: 20,000 Series)
* 4-217-952-01 SHIELD (A)* 4-217-953-01 SHIELD (B)
< CAPACITOR >
C5804 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16VC5805 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16VC5806 1-107-820-11 CERAMIC CHIP 0.1uF 0% 16VC5807 1-164-874-11 CERAMIC CHIP 100PF 5% 16VC5808 1-164-874-11 CERAMIC CHIP 100PF 5% 16V
C5809 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16VC5810 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16VC5811 1-107-820-11 CERAMIC CHIP 0.1uF 0% 16VC5812 1-107-820-11 CERAMIC CHIP 0.1uF 0% 16VC5813 1-107-820-11 CERAMIC CHIP 0.1uF 0% 16V
C5814 1-107-820-11 CERAMIC CHIP 0.1uF 0% 16VC5815 1-107-820-11 CERAMIC CHIP 0.1uF 0% 16VC5816 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10VC5817 1-113-991-11 TANTALUM CHIP 33uF 20% 16VC5818 1-107-820-11 CERAMIC CHIP 0.1uF 0% 16V
C5819 1-107-820-11 CERAMIC CHIP 0.1uF 0% 16VC5820 1-113-682-11 TANTALUM CHIP 33uF 20% 10VC5823 1-164-939-11 CERAMIC CHIP 0.0022uF 10% 16VC5824 1-164-939-11 CERAMIC CHIP 0.0022uF 10% 16VC5825 1-164-939-11 CERAMIC CHIP 0.0022uF 10% 16V
C5826 1-164-939-11 CERAMIC CHIP 0.0022uF 10% 16VC5827 1-164-939-11 CERAMIC CHIP 0.0022uF 10% 16VC5828 1-164-939-11 CERAMIC CHIP 0.0022uF 10% 16VC5829 1-113-991-11 TANTALUM CHIP 33uF 20% 16VC5851 1-115-566-11 CERAMIC CHIP 4.7uF 10% 10V
C5852 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10VC5853 1-164-870-11 CERAMIC CHIP 68PF 5% 16VC5854 1-135-070-00 TANTALUM CHIP 0.1uF 10% 35V
< CONNECTOR >
* CN5801 1-778-158-21 CONNECTOR, FFC/FPC (ZIF) 10PCN5803 1-778-592-21 CONNECTOR, BOARD TO BOARD 50P
< DIODE >
D5801 8-719-048-98 DIODE RB160L-40TE25
< IC >
IC5801 8-759-358-40 IC TLC372CPW-E20IC5802 8-759-572-35 IC TLC3702CPWRIC5803 8-759-358-40 IC TLC372CPW-E20IC5804 8-759-082-55 IC TC7W00FUIC5805 8-759-082-57 IC TC7W04FU
DCM-M1
Les composants identifiés par unemarque 0 sont critiquens pour lasécurité.Ne les remplacer que par une pièceportant le numéro spécifié.
The components identified bymark 0 or dotted line with mark0 are critical for safety.Replace only with part numberspecified.
When indicating parts by referencenumber, please include the board.
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
6-2
CLV ETHER
IC5806 8-759-082-55 IC TC7W00FUIC5807 8-759-572-28 IC NJU7016RIC5808 8-759-082-55 IC TC7W00FUIC5851 8-759-572-54 IC TA6009FN (EL)
< COIL >
L5801 1-416-928-21 INDUCTOR 470uH
< TRANSISTOR >
Q5801 8-729-047-36 TRANSISTOR CPH3303-TLQ5802 8-729-046-70 TRANSISTOR XP4654- (TX).SOQ5803 8-729-037-89 TRANSISTOR 2SC4627J-C (TX).SOQ5808 8-729-037-73 TRANSISTOR UN9212J- (TX).SOQ5809 8-729-037-73 TRANSISTOR UN9212J- (TX).SO
Q5810 8-729-037-73 TRANSISTOR UN9212J- (TX).SOQ5811 8-729-037-73 TRANSISTOR UN9212J- (TX).SOQ5812 8-729-037-73 TRANSISTOR UN9212J- (TX).SOQ5813 8-729-037-73 TRANSISTOR UN9212J- (TX).SOQ5821 8-729-044-26 TRANSISTOR CPH3404-TL
Q5822 8-729-044-26 TRANSISTOR CPH3404-TLQ5823 8-729-044-26 TRANSISTOR CPH3404-TLQ5824 8-729-044-26 TRANSISTOR CPH3404-TLQ5825 8-729-044-26 TRANSISTOR CPH3404-TLQ5826 8-729-044-26 TRANSISTOR CPH3404-TL
< RESISTOR >
R5801 1-218-965-11 RES, CHIP 10K 5% 1/16WR5802 1-218-977-11 RES, CHIP 100K 5% 1/16WR5803 1-218-977-11 RES, CHIP 100K 5% 1/16WR5804 1-218-965-11 RES, CHIP 10K 5% 1/16WR5805 1-218-965-11 RES, CHIP 10K 5% 1/16W
R5806 1-218-971-11 RES, CHIP 33K 5% 1/16WR5807 1-218-953-11 RES, CHIP 1K 5% 1/16WR5808 1-218-965-11 RES, CHIP 10K 5% 1/16WR5809 1-218-971-11 RES, CHIP 33K 5% 1/16WR5810 1-218-953-11 RES, CHIP 1K 5% 1/16W
R5811 1-218-969-11 RES, CHIP 22K 5% 1/16WR5812 1-218-965-11 RES, CHIP 10K 5% 1/16WR5813 1-218-977-11 RES, CHIP 100K 5% 1/16WR5814 1-218-977-11 RES, CHIP 100K 5% 1/16WR5815 1-218-977-11 RES, CHIP 100K 5% 1/16W
R5816 1-218-977-11 RES, CHIP 100K 5% 1/16WR5817 1-218-977-11 RES, CHIP 100K 5% 1/16WR5818 1-218-977-11 RES, CHIP 100K 5% 1/16WR5819 1-218-965-11 RES, CHIP 10K 5% 1/16WR5820 1-218-973-11 RES, CHIP 47K 5% 1/16W
R5821 1-218-955-11 RES, CHIP 1.5K 5% 1/16WR5822 1-218-961-11 RES, CHIP 4.7K 5% 1/16WR5823 1-218-965-11 RES, CHIP 10K 5% 1/16WR5824 1-218-965-11 RES, CHIP 10K 5% 1/16WR5825 1-218-990-11 SHORT 0
R5826 1-218-975-11 RES, CHIP 68K 5% 1/16WR5827 1-218-975-11 RES, CHIP 68K 5% 1/16WR5828 1-218-975-11 RES, CHIP 68K 5% 1/16WR5829 1-218-975-11 RES, CHIP 68K 5% 1/16WR5830 1-218-975-11 RES, CHIP 68K 5% 1/16W
R5831 1-218-975-11 RES, CHIP 68K 5% 1/16W
R5832 1-218-965-11 RES, CHIP 10K 5% 1/16WR5833 1-218-965-11 RES, CHIP 10K 5% 1/16WR5834 1-218-965-11 RES, CHIP 10K 5% 1/16WR5851 1-218-967-11 RES, CHIP 15K 5% 1/16W
R5852 1-218-987-11 RES, CHIP 680K 5% 1/16W
< SWITCH >
S5801 1-692-847-21 SWITCH, PUSH (1 KEY) (PROTECT)S5802 1-692-377-31 SWITCH, PUSH (1 KEY) (REFLECT)S5803 1-692-377-31 SWITCH, PUSH (1 KEY) (MD1/2)S5804 1-572-467-61 SWITCH, PUSH (1 KEY) (INITIAL)S5805 1-572-467-61 SWITCH, PUSH (1 KEY) (IN LIMIT)
< SENSOR >
SE5851 1-418-203-21 SENSOR, SHOCK (SHOCK SENSOR)************************************************************
A-3323-174-A ETHER BOARD, COMPLETE***********************
(Ref. No.: 20,000 Series)
3-043-261-01 SHEET, COPY3-044-616-01 SHEET, SHIELD
< CAPACITOR >
C8801 1-107-820-11 CERAMIC CHIP 0.1uF 0% 16VC8802 1-104-851-11 TANTALUM CHIP 10uF 20% 10VC8803 1-107-820-11 CERAMIC CHIP 0.1uF 0% 16VC8804 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16VC8805 1-107-820-11 CERAMIC CHIP 0.1uF 0% 16V
C8806 1-107-820-11 CERAMIC CHIP 0.1uF 0% 16VC8807 1-164-858-11 CERAMIC CHIP 22PF 5% 16VC8808 1-164-854-11 CERAMIC CHIP 15PF 5% 16VC8809 1-107-820-11 CERAMIC CHIP 0.1uF 0% 16VC8810 1-107-820-11 CERAMIC CHIP 0.1uF 0% 16V
C8811 1-107-820-11 CERAMIC CHIP 0.1uF 0% 16VC8812 1-107-820-11 CERAMIC CHIP 0.1uF 0% 16VC8813 1-107-820-11 CERAMIC CHIP 0.1uF 0% 16VC8814 1-107-820-11 CERAMIC CHIP 0.1uF 0% 16VC8815 1-107-820-11 CERAMIC CHIP 0.1uF 0% 16V
C8816 1-107-820-11 CERAMIC CHIP 0.1uF 0% 16VC8817 1-107-820-11 CERAMIC CHIP 0.1uF 0% 16VC8818 1-107-820-11 CERAMIC CHIP 0.1uF 0% 16VC8819 1-107-820-11 CERAMIC CHIP 0.1uF 0% 16VC8820 1-164-937-11 CERAMIC CHIP 0.001uF 10% 16V
< CONNECTOR >
CN8801 1-778-598-21 CONNECTOR, BOARD TO BOARD 60PCN8802 1-537-439-41 TARMINAL BOARD, CONNECTOR 20P
< IC/FILTER >
IC8801 8-759-573-34 IC 74LVX4245MTCXIC8802 8-759-573-34 IC 74LVX4245MTCXIC8803 8-759-573-34 IC 74LVX4245MTCXIC8804 8-759-573-34 IC 74LVX4245MTCXIC8805 8-759-573-34 IC 74LVX4245MTCX
IC8806 8-759-572-50 IC MB86967PFV-G-BNDIC8807 1-803-453-11 FILTER MODULE, PCMCIAIC8808 8-759-573-35 IC KM62256DLTG-7L
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
6-3
ETHER JACK LCD
< COIL >
L8801 1-414-753-91 INDUCTOR 4.7uH
< TRANSISTOR >
Q8801 8-729-047-36 TRANSISTOR CPH3303-TL
< RESISTOR >
R8801 1-218-977-11 RES, CHIP 100K 5% 1/16WR8803 1-218-957-11 RES, CHIP 2.2K 5% 1/16W
< VIBRATOR >
X8801 1-781-265-21 VIBRATOR, CRYSTAL (20MHz)************************************************************
A-3321-883-A JACK BOARD, COMPLETE**********************
(Ref. No.: 20,000 Series)
< CAPACITOR >
C1001 1-164-937-11 CERAMIC CHIP 0.001uF 10% 16VC1014 1-164-937-11 CERAMIC CHIP 0.001uF 10% 16VC2001 1-164-937-11 CERAMIC CHIP 0.001uF 10% 16VC2014 1-164-937-11 CERAMIC CHIP 0.001uF 10% 16VC3008 1-164-937-11 CERAMIC CHIP 0.001uF 10% 16V
C3060 1-164-937-11 CERAMIC CHIP 0.001uF 10% 16VC3061 1-164-937-11 CERAMIC CHIP 0.001uF 10% 16V
< CONNECTOR >
CN3003 1-778-596-21 CONNECTOR, BOARD TO BOARD 30PCN8004 1-778-711-11 CONNECTOR, FFC/FPC (ZIF) 5P
< DIODE >
D1001 8-719-074-62 DIODE MAZS082001SOD1002 8-719-074-62 DIODE MAZS082001SOD2001 8-719-074-62 DIODE MAZS082001SOD2002 8-719-074-62 DIODE MAZS082001SOD3001 8-719-074-62 DIODE MAZS082001SO
D3002 8-719-074-62 DIODE MAZS082001SOD3003 8-719-074-62 DIODE MAZS082001SOD3004 8-719-074-62 DIODE MAZS082001SOD3005 8-719-074-62 DIODE MAZS082001SOD3006 8-719-074-62 DIODE MAZS082001SO
D3007 8-719-074-62 DIODE MAZS082001SOD3008 8-719-074-62 DIODE MAZS082001SOD4001 8-719-074-62 DIODE MAZS082001SOD4002 8-719-074-62 DIODE MAZS082001SOD4003 8-719-074-62 DIODE MAZS082001SO
D4004 8-719-074-62 DIODE MAZS082001SOD4005 8-719-074-62 DIODE MAZS082001SOD8011 8-719-074-62 DIODE MAZS082001SOD8012 8-719-074-62 DIODE MAZS082001SOD8013 8-719-074-62 DIODE MAZS082001SO
< FERRITE BEAD >
FB1101 1-469-637-21 FERRITE 0uHFB1102 1-469-637-21 FERRITE 0uHFB1103 1-469-637-21 FERRITE 0uH
FB2101 1-469-637-21 FERRITE 0uHFB2102 1-469-637-21 FERRITE 0uH
FB2103 1-469-637-21 FERRITE 0uHFB3001 1-469-637-21 FERRITE 0uHFB3002 1-469-637-21 FERRITE 0uHFB3003 1-469-637-21 FERRITE 0uHFB3101 1-469-637-21 FERRITE 0uH
< JACK/CONNECTOR >
J3001 1-779-881-21 JACK (MIC)J3002 1-569-950-21 JACK (i)J3003 1-778-040-11 JACK, SMALL TYPE (AUDIO/VIDEO)J4001 1-779-870-11 CONNECTOR (ROUND TYPE) 4P (S. VIDEO)
< RESISTOR >
R3051 1-218-990-11 SHORT 0R3052 1-218-990-11 SHORT 0R3053 1-218-990-11 SHORT 0R3055 1-218-990-11 SHORT 0R4051 1-216-821-11 METAL CHIP 1K 5% 1/16W
< VARISTOR >
VDR103 1-801-923-11 VARISTOR, CHIPVDR203 1-801-923-11 VARISTOR, CHIP
************************************************************
A-3323-169-A LCD BOARD, COMPLETE*********************
(Ref. No.: 20,000 Series)
4-220-440-01 SHEET (LCD), SHIELD
< CAPACITOR >
C4301 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10VC4302 1-117-919-11 TANTALUM CHIP 10uF 20% 6.3VC4303 1-117-919-11 TANTALUM CHIP 10uF 20% 6.3VC4304 1-119-750-11 TANTALUM CHIP 22uF 20% 6.3VC4305 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V
C4306 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10VC4307 1-117-919-11 TANTALUM CHIP 10uF 20% 6.3VC4308 1-104-752-11 TANTALUM CHIP 33uF 20% 6.3VC4309 1-164-004-11 CERAMIC CHIP 0.1uF 10% 25VC4310 1-119-750-11 TANTALUM CHIP 22uF 20% 6.3V
C4311 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10VC4312 1-135-180-21 TANTALUM CHIP 3.3uF 20% 6.3VC4313 1-164-004-11 CERAMIC CHIP 0.1uF 10% 25VC4314 1-119-750-11 TANTALUM CHIP 22uF 20% 6.3VC4315 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16V
C4316 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10VC4317 1-119-751-11 TANTALUM CHIP 22uF 20% 16VC4318 1-164-004-11 CERAMIC CHIP 0.1uF 10% 25VC4319 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10VC4320 1-164-866-11 CERAMIC CHIP 47PF 5% 16V
C4321 1-164-882-11 CERAMIC CHIP 220PF 5% 16VC4322 1-110-501-11 CERAMIC CHIP 0.33uF 10% 16VC4323 1-110-501-11 CERAMIC CHIP 0.33uF 10% 16VC4324 1-110-501-11 CERAMIC CHIP 0.33uF 10% 16VC4325 1-104-851-11 TANTALUM CHIP 10uF 20% 10V
C4326 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
6-4
C4327 1-117-919-11 TANTALUM CHIP 10uF 20% 6.3VC4328 1-164-004-11 CERAMIC CHIP 0.1uF 10% 25VC4329 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10VC4330 1-110-501-11 CERAMIC CHIP 0.33uF 10% 16V
C4331 1-164-870-11 CERAMIC CHIP 68PF 5% 16VC4332 1-164-004-11 CERAMIC CHIP 0.1uF 10% 25VC4334 1-164-937-11 CERAMIC CHIP 0.001uF 10% 16VC4335 1-164-862-11 CERAMIC CHIP 33PF 5% 16VC4336 1-164-004-11 CERAMIC CHIP 0.1uF 10% 25V
C4337 1-164-934-11 CERAMIC CHIP 330PF 10% 16VC4338 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10VC4339 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10VC4340 1-113-985-11 TANTALUM CHIP 10uF 20% 20VC4341 1-109-982-11 CERAMIC CHIP 1uF 10% 10V
C4342 1-113-985-11 TANTALUM CHIP 10uF 20% 20VC4344 1-107-682-11 CERAMIC CHIP 1uF 10% 16VC4345 1-119-751-11 TANTALUM CHIP 22uF 20% 16VC4346 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10VC4352 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V
< CONNECTOR >
* CN4301 1-778-154-21 CONNECTOR, FFC/FPC (ZIF) 6P* CN4302 1-785-283-41 PIN, CONNECTOR (PC BOARD) 14P
CN4303 1-785-283-21 PIN, CONNECTOR (PC BOARD) 14PCN4305 1-764-708-21 CONNECTOR, FFC/FPC (LIF) 9P
* CN4306 1-778-172-11 CONNECTOR, FFC/FPC (ZIF) 24P
* CN4307 1-569-352-11 HOUSING, CONNECTOR 10P
< DIODE >
D4302 8-713-102-80 DIODE 1T369-01-T8AD4303 8-713-102-80 DIODE 1T369-01-T8AD4304 8-719-421-69 DIODE MA133
< FERRITE BEAD >
FB4301 1-414-445-11 FERRITE 0uH
< IC >
IC4301 8-759-596-12 IC AK9813AFS-E2IC4302 8-759-539-27 IC IR3Y37A4IC4303 8-759-524-61 IC CM7018L3-T4IC4304 8-759-327-01 IC NJM062V (TE2)
< COIL >
L4301 1-414-754-11 INDUCTOR 10uHL4302 1-414-754-11 INDUCTOR 10uHL4303 1-414-404-41 INDUCTOR 100uHL4305 1-414-754-11 INDUCTOR 10uHL4306 1-414-754-11 INDUCTOR 10uH
L4307 1-414-754-11 INDUCTOR 10uHL4308 1-412-945-11 INDUCTOR 3.3uHL4309 1-414-754-11 INDUCTOR 10uH
< TRANSISTOR >
Q4301 8-729-044-38 TRANSISTOR SI6552DQ-T1Q4302 8-729-044-38 TRANSISTOR SI6552DQ-T1Q4303 8-729-037-53 TRANSISTOR 2SB1462J-QR (TX).SOQ4304 8-729-037-53 TRANSISTOR 2SB1462J-QR (TX).SOQ4305 8-729-037-53 TRANSISTOR 2SB1462J-QR (TX).SO
Q4306 8-729-037-53 TRANSISTOR 2SB1462J-QR (TX).SOQ4307 8-729-037-53 TRANSISTOR 2SB1462J-QR (TX).SOQ4308 8-729-037-53 TRANSISTOR 2SB1462J-QR (TX).SOQ4312 8-729-037-52 TRANSISTOR 2SD2216J-QR (TX).SOQ4313 8-729-037-53 TRANSISTOR 2SB1462J-QR (TX).SO
< RESISTOR >
R4301 1-208-691-11 METAL CHIP 2.2K 0.5% 1/16WR4302 1-208-675-11 METAL CHIP 470 0.5% 1/16WR4303 1-208-683-11 METAL CHIP 1K 0.5% 1/16WR4304 1-218-971-11 RES, CHIP 33K 5% 1/16WR4305 1-218-975-11 RES, CHIP 68K 5% 1/16W
R4309 1-218-929-11 RES, CHIP 10 5% 1/16WR4310 1-218-973-11 RES, CHIP 47K 5% 1/16WR4313 1-218-957-11 RES, CHIP 2.2K 5% 1/16WR4314 1-218-849-11 METAL CHIP 3.3K 0.5% 1/16WR4315 1-208-675-11 METAL CHIP 470 0.5% 1/16W
R4316 1-208-683-11 METAL CHIP 1K 0.5% 1/16WR4317 1-218-971-11 RES, CHIP 33K 5% 1/16WR4318 1-218-967-11 RES, CHIP 15K 5% 1/16WR4319 1-218-967-11 RES, CHIP 15K 5% 1/16WR4320 1-218-967-11 RES, CHIP 15K 5% 1/16W
R4321 1-218-971-11 RES, CHIP 33K 5% 1/16WR4322 1-218-975-11 RES, CHIP 68K 5% 1/16WR4323 1-218-969-11 RES, CHIP 22K 5% 1/16WR4324 1-218-967-11 RES, CHIP 15K 5% 1/16WR4325 1-218-973-11 RES, CHIP 47K 5% 1/16W
R4326 1-218-967-11 RES, CHIP 15K 5% 1/16WR4327 1-218-971-11 RES, CHIP 33K 5% 1/16WR4328 1-218-957-11 RES, CHIP 2.2K 5% 1/16WR4329 1-218-963-11 RES, CHIP 6.8K 5% 1/16WR4330 1-218-975-11 RES, CHIP 68K 5% 1/16W
R4331 1-218-983-11 RES, CHIP 330K 5% 1/16WR4334 1-218-990-11 SHORT 0R4335 1-208-691-11 METAL CHIP 2.2K 0.5% 1/16WR4336 1-208-675-11 METAL CHIP 470 0.5% 1/16WR4337 1-208-683-11 METAL CHIP 1K 0.5% 1/16W
R4338 1-218-929-11 RES, CHIP 10 5% 1/16WR4339 1-218-971-11 RES, CHIP 33K 5% 1/16WR4340 1-218-975-11 RES, CHIP 68K 5% 1/16WR4343 1-218-977-11 RES, CHIP 100K 5% 1/16WR4344 1-218-957-11 RES, CHIP 2.2K 5% 1/16W
R4345 1-218-990-11 SHORT 0R4347 1-218-965-11 RES, CHIP 10K 5% 1/16WR4350 1-216-009-91 RES, CHIP 22 5% 1/10WR4351 1-218-990-11 SHORT 0R4353 1-218-975-11 RES, CHIP 68K 5% 1/16W
R4354 1-218-990-11 SHORT 0R4356 1-218-983-11 RES, CHIP 330K 5% 1/16WR4357 1-218-975-11 RES, CHIP 68K 5% 1/16WR4358 1-218-990-11 SHORT 0R4359 1-208-939-11 METAL CHIP 150K 0.5% 1/16W
R4360 1-208-955-11 METAL CHIP 680K 0.5% 1/16WR4362 1-218-990-11 SHORT 0R4366 1-208-931-11 METAL CHIP 68K 0.5% 1/16WR4369 1-218-965-11 RES, CHIP 10K 5% 1/16WR4370 1-218-989-11 RES, CHIP 1M 5% 1/16W
LCD
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
6-5
R4371 1-218-975-11 RES, CHIP 68K 5% 1/16WR4372 1-218-969-11 RES, CHIP 22K 5% 1/16WR4373 1-218-973-11 RES, CHIP 47K 5% 1/16WR4374 1-218-961-11 RES, CHIP 4.7K 5% 1/16WR4375 1-218-933-11 RES, CHIP 22 5% 1/16W
R4376 1-218-975-11 RES, CHIP 68K 5% 1/16WR4377 1-218-961-11 RES, CHIP 4.7K 5% 1/16WR4378 1-218-977-11 RES, CHIP 100K 5% 1/16WR4379 1-218-971-11 RES, CHIP 33K 5% 1/16WR4380 1-218-977-11 RES, CHIP 100K 5% 1/16W
R4381 1-218-971-11 RES, CHIP 33K 5% 1/16WR4382 1-218-967-11 RES, CHIP 15K 5% 1/16WR4383 1-218-965-11 RES, CHIP 10K 5% 1/16WR4384 1-218-929-11 RES, CHIP 10 5% 1/16WR4385 1-218-929-11 RES, CHIP 10 5% 1/16W
R4386 1-218-990-11 SHORT 0R4387 1-218-937-11 RES, CHIP 47 5% 1/16WR4388 1-218-937-11 RES, CHIP 47 5% 1/16WR4389 1-218-937-11 RES, CHIP 47 5% 1/16WR4390 1-218-961-11 RES, CHIP 4.7K 5% 1/16W
R4391 1-218-977-11 RES, CHIP 100K 5% 1/16WR4392 1-218-961-11 RES, CHIP 4.7K 5% 1/16WR4393 1-218-990-11 SHORT 0R4394 1-218-990-11 SHORT 0R4395 1-218-990-11 SHORT 0
R4396 1-218-990-11 SHORT 0R4397 1-218-971-11 RES, CHIP 33K 5% 1/16WR4400 1-218-990-11 SHORT 0R4401 1-218-933-11 RES, CHIP 22 5% 1/16WR4402 1-208-719-11 METAL CHIP 33K 0.5% 1/16W
R4403 1-218-961-11 RES, CHIP 4.7K 5% 1/16WR4405 1-208-711-11 METAL CHIP 15K 0.5% 1/16WR4407 1-208-707-11 METAL CHIP 10K 0.5% 1/16WR4408 1-217-671-11 METAL CHIP 1 5% 1/10WR4409 1-217-671-11 METAL CHIP 1 5% 1/10W
************************************************************
A-3323-422-A MAIN BOARD, COMPLETE*********************
(Ref. No.: 10,000 Series)
< CAPACITOR >
C1003 1-163-077-00 CERAMIC CHIP 0.1uF 10% 25VC1004 1-125-891-11 CERAMIC CHIP 0.47uF 10% 10VC1005 1-164-480-11 CERAMIC CHIP 0.01uF 10% 50VC1006 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10VC1007 1-164-677-11 CERAMIC CHIP 0.033uF 10% 16V
C1008 1-162-967-11 CERAMIC CHIP 0.0033uF 10% 50VC1009 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16VC1010 1-164-677-11 CERAMIC CHIP 0.033uF 10% 16VC1011 1-164-677-11 CERAMIC CHIP 0.033uF 10% 16VC1012 1-164-874-11 CERAMIC CHIP 100PF 5% 16V
C1013 1-135-337-11 TANTALUM CHIP 1uF 20% 6.3VC1014 1-125-837-91 CERAMIC CHIP 1uF 10% 6.3VC1015 1-135-177-21 TANTALUM CHIP 1uF 20% 20VC1016 1-125-837-91 CERAMIC CHIP 1uF 10% 6.3VC1017 1-117-919-11 TANTALUM CHIP 10uF 20% 6.3V
C1018 1-117-919-11 TANTALUM CHIP 10uF 20% 6.3VC1019 1-164-935-11 CERAMIC CHIP 470PF 10% 16V
C1020 1-107-686-11 TANTALUM CHIP 4.7uF 20% 16VC1021 1-125-891-11 CERAMIC CHIP 0.47uF 10% 10VC1022 1-164-939-11 CERAMIC CHIP 0.0022uF 10% 16V
C2003 1-163-077-00 CERAMIC CHIP 0.1uF 10% 25VC2004 1-125-891-11 CERAMIC CHIP 0.47uF 10% 10VC2005 1-164-480-11 CERAMIC CHIP 0.01uF 10% 50VC2006 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10VC2007 1-164-677-11 CERAMIC CHIP 0.033uF 10% 16V
C2008 1-162-967-11 CERAMIC CHIP 0.0033uF 10% 50VC2009 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16VC2010 1-164-677-11 CERAMIC CHIP 0.033uF 10% 16VC2011 1-164-677-11 CERAMIC CHIP 0.033uF 10% 16VC2012 1-164-874-11 CERAMIC CHIP 100PF 5% 16V
C2013 1-135-337-11 TANTALUM CHIP 1uF 20% 6.3VC2014 1-125-837-91 CERAMIC CHIP 1uF 10% 6.3VC2015 1-135-177-21 TANTALUM CHIP 1uF 20% 20VC2016 1-125-837-91 CERAMIC CHIP 1uF 10% 6.3VC2017 1-117-919-11 TANTALUM CHIP 10uF 20% 6.3V
C2018 1-117-919-11 TANTALUM CHIP 10uF 20% 6.3VC2019 1-164-935-11 CERAMIC CHIP 470PF 10% 16VC2020 1-107-686-11 TANTALUM CHIP 4.7uF 20% 16VC2021 1-125-891-11 CERAMIC CHIP 0.47uF 10% 10VC2022 1-164-939-11 CERAMIC CHIP 0.0022uF 10% 16V
C3001 1-164-937-11 CERAMIC CHIP 0.001uF 10% 16VC3002 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16VC3003 1-135-337-11 TANTALUM CHIP 1uF 20% 6.3VC3004 1-107-820-11 CERAMIC CHIP 0.1uF 0% 16VC3005 1-117-919-11 TANTALUM CHIP 10uF 20% 6.3V
C3006 1-107-820-11 CERAMIC CHIP 0.1uF 0% 16VC3007 1-107-820-11 CERAMIC CHIP 0.1uF 0% 16VC3008 1-125-891-11 CERAMIC CHIP 0.47uF 10% 10VC3011 1-117-919-11 TANTALUM CHIP 10uF 20% 6.3VC3013 1-107-820-11 CERAMIC CHIP 0.1uF 0% 16V
C3014 1-107-686-11 TANTALUM CHIP 4.7uF 20% 16VC3015 1-107-820-11 CERAMIC CHIP 0.1uF 0% 16VC3016 1-107-686-11 TANTALUM CHIP 4.7uF 20% 16VC3017 1-107-820-11 CERAMIC CHIP 0.1uF 0% 16VC3018 1-135-337-11 TANTALUM CHIP 1uF 20% 6.3V
C3019 1-107-820-11 CERAMIC CHIP 0.1uF 0% 16VC3021 1-119-750-11 TANTALUM CHIP 22uF 20% 6.3VC3022 1-107-820-11 CERAMIC CHIP 0.1uF 0% 16VC3023 1-110-569-11 TANTALUM CHIP 47uF 20% 6.3VC3025 1-107-820-11 CERAMIC CHIP 0.1uF 0% 16V
C3026 1-117-919-11 TANTALUM CHIP 10uF 20% 6.3VC3027 1-107-820-11 CERAMIC CHIP 0.1uF 0% 16VC3028 1-110-569-11 TANTALUM CHIP 47uF 20% 6.3VC3030 1-119-750-11 TANTALUM CHIP 22uF 20% 6.3VC3031 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V
C3032 1-117-919-11 TANTALUM CHIP 10uF 20% 6.3VC3033 1-135-337-11 TANTALUM CHIP 1uF 20% 6.3VC3034 1-119-750-11 TANTALUM CHIP 22uF 20% 6.3VC3035 1-135-337-11 TANTALUM CHIP 1uF 20% 6.3VC3036 1-117-919-11 TANTALUM CHIP 10uF 20% 6.3V
C3037 1-107-826-91 CERAMIC CHIP 0.1uF 10% 16VC3038 1-107-826-91 CERAMIC CHIP 0.1uF 10% 16VC3039 1-164-874-11 CERAMIC CHIP 100PF 5% 16VC3040 1-125-926-91 TANTALUM CHIP 4.7uF 20% 6.3VC3041 1-107-820-11 CERAMIC CHIP 0.1uF 0% 16V
LCD MAIN
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
6-6
C3042 1-107-820-11 CERAMIC CHIP 0.1uF 0% 16VC3043 1-107-820-11 CERAMIC CHIP 0.1uF 0% 16VC3044 1-117-919-11 TANTALUM CHIP 10uF 20% 6.3VC3045 1-107-820-11 CERAMIC CHIP 0.1uF 0% 16VC3046 1-107-820-11 CERAMIC CHIP 0.1uF 0% 16V
C3047 1-107-820-11 CERAMIC CHIP 0.1uF 0% 16VC3048 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10VC3049 1-107-820-11 CERAMIC CHIP 0.1uF 0% 16VC3050 1-107-820-11 CERAMIC CHIP 0.1uF 0% 16VC3051 1-119-750-11 TANTALUM CHIP 22uF 20% 6.3V
C3052 1-107-820-11 CERAMIC CHIP 0.1uF 0% 16VC3053 1-117-919-11 TANTALUM CHIP 10uF 20% 6.3VC3055 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16VC4001 1-104-851-11 TANTALUM CHIP 10uF 20% 10VC4002 1-104-851-11 TANTALUM CHIP 10uF 20% 10V
C4003 1-104-851-11 TANTALUM CHIP 10uF 20% 10VC4004 1-119-749-11 TANTALUM CHIP 33uF 20% 4VC4005 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10VC4006 1-135-181-21 TANTALUM CHIP 4.7uF 20% 6.3VC4007 1-135-181-21 TANTALUM CHIP 4.7uF 20% 6.3V
C4008 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10VC4009 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16VC4010 1-125-899-11 TANTALUM CHIP 220uF 20% 4VC4011 1-119-749-11 TANTALUM CHIP 33uF 20% 4VC4012 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V
C4013 1-135-181-21 TANTALUM CHIP 4.7uF 20% 6.3VC4014 1-135-181-21 TANTALUM CHIP 4.7uF 20% 6.3VC4015 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10VC4017 1-104-847-11 TANTALUM CHIP 22uF 20% 4VC4018 1-125-899-11 TANTALUM CHIP 220uF 20% 4V
C4019 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10VC4020 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10VC4021 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10VC4022 1-135-337-11 TANTALUM CHIP 1uF 20% 6.3VC4023 1-107-820-11 CERAMIC CHIP 0.1uF 0% 16V
C4024 1-115-467-11 CERAMIC CHIP 0.22uF 10% 10VC4026 1-107-820-11 CERAMIC CHIP 0.1uF 0% 16VC4027 1-107-820-11 CERAMIC CHIP 0.1uF 0% 16VC4028 1-115-467-11 CERAMIC CHIP 0.22uF 10% 10VC4029 1-107-820-11 CERAMIC CHIP 0.1uF 0% 16V
C4031 1-107-820-11 CERAMIC CHIP 0.1uF 0% 16VC4032 1-107-820-11 CERAMIC CHIP 0.1uF 0% 16VC5001 1-164-937-11 CERAMIC CHIP 0.001uF 10% 16VC5002 1-107-820-11 CERAMIC CHIP 0.1uF 0% 16VC5003 1-119-750-11 TANTALUM CHIP 22uF 20% 6.3V
C5004 1-107-820-11 CERAMIC CHIP 0.1uF 0% 16VC5005 1-119-750-11 TANTALUM CHIP 22uF 20% 6.3VC5006 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10VC5007 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10VC5008 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16V
C5009 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16VC5011 1-113-985-11 TANTALUM CHIP 10uF 20% 20VC5012 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10VC5013 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10VC5014 1-125-837-91 CERAMIC CHIP 1uF 10% 6.3V
C5015 1-107-819-11 CERAMIC CHIP 0.022uF 10% 16VC5016 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16V
C5017 1-115-467-11 CERAMIC CHIP 0.22uF 10% 10VC5018 1-164-942-11 CERAMIC CHIP 0.0068uF 10% 16VC5019 1-119-923-81 CERAMIC CHIP 0.047uF 10% 10V
C5020 1-164-938-11 CERAMIC CHIP 0.0015uF 10% 16VC5021 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16VC5022 1-125-837-91 CERAMIC CHIP 1uF 10% 6.3VC5023 1-110-563-11 CERAMIC CHIP 0.068uF 10% 16VC5024 1-164-677-11 CERAMIC CHIP 0.033uF 10% 16V
C5025 1-107-820-11 CERAMIC CHIP 0.1uF 0% 16VC5026 1-104-851-11 TANTALUM CHIP 10uF 20% 10VC5027 1-107-820-11 CERAMIC CHIP 0.1uF 0% 16VC5028 1-107-820-11 CERAMIC CHIP 0.1uF 0% 16VC5029 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16V
C5030 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16VC5031 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10VC5032 1-107-820-11 CERAMIC CHIP 0.1uF 0% 16VC5033 1-107-820-11 CERAMIC CHIP 0.1uF 0% 16VC5034 1-119-923-81 CERAMIC CHIP 0.047uF 10% 10V
C5035 1-107-820-11 CERAMIC CHIP 0.1uF 0% 16VC5036 1-107-820-11 CERAMIC CHIP 0.1uF 0% 16VC5037 1-107-820-11 CERAMIC CHIP 0.1uF 0% 16VC5038 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16VC5039 1-119-923-81 CERAMIC CHIP 0.047uF 10% 10V
C5040 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10VC5041 1-107-820-11 CERAMIC CHIP 0.1uF 0% 16VC5042 1-164-870-11 CERAMIC CHIP 68PF 5% 16VC5043 1-164-862-11 CERAMIC CHIP 33PF 5% 16VC5044 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V
C5045 1-107-820-11 CERAMIC CHIP 0.1uF 0% 16VC5046 1-164-870-11 CERAMIC CHIP 68PF 5% 16VC5047 1-164-862-11 CERAMIC CHIP 33PF 5% 16VC5048 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10VC5049 1-107-820-11 CERAMIC CHIP 0.1uF 0% 16V
C5051 1-107-820-11 CERAMIC CHIP 0.1uF 0% 16VC5052 1-107-820-11 CERAMIC CHIP 0.1uF 0% 16VC5055 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10VC5056 1-107-819-11 CERAMIC CHIP 0.022uF 10% 16VC5057 1-107-819-11 CERAMIC CHIP 0.022uF 10% 16V
C5101 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10VC5102 1-125-837-91 CERAMIC CHIP 1uF 10% 6.3VC5103 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16VC5104 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16VC5105 1-104-851-11 TANTALUM CHIP 10uF 20% 10V
C5106 1-107-820-11 CERAMIC CHIP 0.1uF 0% 16VC5201 1-107-826-91 CERAMIC CHIP 0.1uF 10% 16VC5202 1-107-826-91 CERAMIC CHIP 0.1uF 10% 16VC5203 1-107-820-11 CERAMIC CHIP 0.1uF 0% 16VC5204 1-164-850-11 CERAMIC CHIP 10PF 0.5PF 16V
C5205 1-164-850-11 CERAMIC CHIP 10PF 0.5PF 16VC5206 1-164-940-11 CERAMIC CHIP 0.0033uF 10% 16VC5207 1-164-940-11 CERAMIC CHIP 0.0033uF 10% 16VC5208 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10VC5209 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V
C5212 1-107-820-11 CERAMIC CHIP 0.1uF 0% 16VC5301 1-110-569-11 TANTALUM CHIP 47uF 20% 6.3VC5302 1-119-750-11 TANTALUM CHIP 22uF 20% 6.3VC5303 1-107-820-11 CERAMIC CHIP 0.1uF 0% 16VC5304 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V
MAIN
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
6-7
C5305 1-107-820-11 CERAMIC CHIP 0.1uF 0% 16VC5306 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10VC5307 1-164-847-11 CERAMIC CHIP 7PF 0.5PF 16VC5308 1-164-677-11 CERAMIC CHIP 0.033uF 10% 16VC5309 1-164-847-11 CERAMIC CHIP 7PF 0.5PF 16V
C5310 1-125-891-11 CERAMIC CHIP 0.47uF 10% 10VC5311 1-107-820-11 CERAMIC CHIP 0.1uF 0% 16VC5312 1-164-939-11 CERAMIC CHIP 0.0022uF 10% 16VC5313 1-164-874-11 CERAMIC CHIP 100PF 5% 16VC5314 1-107-820-11 CERAMIC CHIP 0.1uF 0% 16V
C5315 1-125-891-11 CERAMIC CHIP 0.47uF 10% 10VC5316 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16VC5317 1-107-820-11 CERAMIC CHIP 0.1uF 0% 16VC5318 1-107-820-11 CERAMIC CHIP 0.1uF 0% 16VC5319 1-107-820-11 CERAMIC CHIP 0.1uF 0% 16V
C5401 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10VC5402 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10VC5403 1-107-820-11 CERAMIC CHIP 0.1uF 0% 16VC5404 1-107-820-11 CERAMIC CHIP 0.1uF 0% 16VC5405 1-107-820-11 CERAMIC CHIP 0.1uF 0% 16V
C5406 1-107-820-11 CERAMIC CHIP 0.1uF 0% 16VC5407 1-107-820-11 CERAMIC CHIP 0.1uF 0% 16VC5408 1-107-820-11 CERAMIC CHIP 0.1uF 0% 16VC5409 1-164-845-11 CERAMIC CHIP 5PF 0.25PF 16VC5410 1-164-845-11 CERAMIC CHIP 5PF 0.25PF 16V
C5411 1-107-820-11 CERAMIC CHIP 0.1uF 0% 16VC5412 1-107-820-11 CERAMIC CHIP 0.1uF 0% 16VC5413 1-107-820-11 CERAMIC CHIP 0.1uF 0% 16VC5414 1-119-750-11 TANTALUM CHIP 22uF 20% 6.3VC5415 1-107-820-11 CERAMIC CHIP 0.1uF 0% 16V
C5417 1-164-845-11 CERAMIC CHIP 5PF 0.25PF 16VC5418 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16VC5419 1-107-820-11 CERAMIC CHIP 0.1uF 0% 16VC5420 1-107-820-11 CERAMIC CHIP 0.1uF 0% 16VC5421 1-164-850-11 CERAMIC CHIP 10PF 0.5PF 16V
C5424 1-164-842-11 CERAMIC CHIP 2PF 0.25PF 16VC5501 1-107-820-11 CERAMIC CHIP 0.1uF 0% 16VC5503 1-107-820-11 CERAMIC CHIP 0.1uF 0% 16VC5601 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10VC5602 1-119-751-11 TANTALUM CHIP 22uF 20% 16V
C5603 1-107-820-11 CERAMIC CHIP 0.1uF 0% 16VC5604 1-104-912-11 TANTALUM CHIP 3.3uF 20% 16VC5605 1-113-985-11 TANTALUM CHIP 10uF 20% 20VC5606 1-104-912-11 TANTALUM CHIP 3.3uF 20% 16VC5607 1-104-912-11 TANTALUM CHIP 3.3uF 20% 16V
C5608 1-104-912-11 TANTALUM CHIP 3.3uF 20% 16VC5609 1-113-682-11 TANTALUM CHIP 33uF 20% 10VC5610 1-113-682-11 TANTALUM CHIP 33uF 20% 10VC5614 1-113-642-11 TANTALUM CHIP 47uF 20% 10VC5615 1-164-874-11 CERAMIC CHIP 100PF 5% 16V
C8001 1-119-750-11 TANTALUM CHIP 22uF 20% 6.3VC8002 1-107-820-11 CERAMIC CHIP 0.1uF 0% 16VC8003 1-164-847-11 CERAMIC CHIP 7PF 0.5PF 16VC8004 1-164-847-11 CERAMIC CHIP 7PF 0.5PF 16VC8005 1-107-820-11 CERAMIC CHIP 0.1uF 0% 16V
C8006 1-107-820-11 CERAMIC CHIP 0.1uF 0% 16VC8007 1-107-820-11 CERAMIC CHIP 0.1uF 0% 16V
C8008 1-107-820-11 CERAMIC CHIP 0.1uF 0% 16VC8009 1-107-820-11 CERAMIC CHIP 0.1uF 0% 16VC8010 1-107-820-11 CERAMIC CHIP 0.1uF 0% 16V
C8011 1-107-820-11 CERAMIC CHIP 0.1uF 0% 16VC8012 1-107-820-11 CERAMIC CHIP 0.1uF 0% 16VC8013 1-107-820-11 CERAMIC CHIP 0.1uF 0% 16VC8014 1-107-820-11 CERAMIC CHIP 0.1uF 0% 16VC8015 1-107-820-11 CERAMIC CHIP 0.1uF 0% 16V
C8016 1-164-935-11 CERAMIC CHIP 470PF 10% 16VC8017 1-164-935-11 CERAMIC CHIP 470PF 10% 16VC8018 1-107-820-11 CERAMIC CHIP 0.1uF 0% 16VC8019 1-107-820-11 CERAMIC CHIP 0.1uF 0% 16VC8020 1-164-858-11 CERAMIC CHIP 22PF 5% 16V
C8021 1-164-858-11 CERAMIC CHIP 22PF 5% 16VC8022 1-119-750-11 TANTALUM CHIP 22uF 20% 6.3VC8023 1-107-820-11 CERAMIC CHIP 0.1uF 0% 16VC8024 1-107-820-11 CERAMIC CHIP 0.1uF 0% 16VC8025 1-107-820-11 CERAMIC CHIP 0.1uF 0% 16V
C8026 1-164-937-11 CERAMIC CHIP 0.001uF 10% 16VC8027 1-119-750-11 TANTALUM CHIP 22uF 20% 6.3VC8028 1-107-820-11 CERAMIC CHIP 0.1uF 0% 16VC8029 1-107-820-11 CERAMIC CHIP 0.1uF 0% 16VC8030 1-125-891-11 CERAMIC CHIP 0.47uF 10% 10V
C8031 1-107-820-11 CERAMIC CHIP 0.1uF 0% 16VC8032 1-107-820-11 CERAMIC CHIP 0.1uF 0% 16VC8033 1-107-820-11 CERAMIC CHIP 0.1uF 0% 16VC8034 1-107-820-11 CERAMIC CHIP 0.1uF 0% 16VC8035 1-119-751-11 TANTALUM CHIP 22uF 20% 16V
C8036 1-107-820-11 CERAMIC CHIP 0.1uF 0% 16VC8037 1-107-820-11 CERAMIC CHIP 0.1uF 0% 16VC8038 1-115-565-11 CERAMIC CHIP 2.2uF 10% 10VC8039 1-107-820-11 CERAMIC CHIP 0.1uF 0% 16VC8040 1-107-820-11 CERAMIC CHIP 0.1uF 0% 16V
C8041 1-107-820-11 CERAMIC CHIP 0.1uF 0% 16VC8042 1-107-820-11 CERAMIC CHIP 0.1uF 0% 16VC8043 1-119-750-11 TANTALUM CHIP 22uF 20% 6.3VC8044 1-107-820-11 CERAMIC CHIP 0.1uF 0% 16VC8045 1-107-820-11 CERAMIC CHIP 0.1uF 0% 16V
C8046 1-107-820-11 CERAMIC CHIP 0.1uF 0% 16VC8047 1-107-820-11 CERAMIC CHIP 0.1uF 0% 16VC8048 1-107-820-11 CERAMIC CHIP 0.1uF 0% 16VC8049 1-107-820-11 CERAMIC CHIP 0.1uF 0% 16VC8050 1-107-820-11 CERAMIC CHIP 0.1uF 0% 16V
C8051 1-107-820-11 CERAMIC CHIP 0.1uF 0% 16VC8052 1-107-820-11 CERAMIC CHIP 0.1uF 0% 16VC8053 1-164-874-11 CERAMIC CHIP 100PF 5% 16VC8055 1-107-820-11 CERAMIC CHIP 0.1uF 0% 16VC8056 1-107-820-11 CERAMIC CHIP 0.1uF 0% 16V
C8057 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10VC8059 1-107-820-11 CERAMIC CHIP 0.1uF 0% 16VC8062 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10VC8063 1-107-820-11 CERAMIC CHIP 0.1uF 0% 16VC8064 1-107-820-11 CERAMIC CHIP 0.1uF 0% 16V
C8065 1-107-820-11 CERAMIC CHIP 0.1uF 0% 16VC8067 1-107-820-11 CERAMIC CHIP 0.1uF 0% 16VC8068 1-164-845-11 CERAMIC CHIP 5PF 0.25PF 16VC8069 1-107-820-11 CERAMIC CHIP 0.1uF 0% 16VC8070 1-119-750-11 TANTALUM CHIP 22uF 20% 6.3V
MAIN
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
6-8
C8071 1-164-937-11 CERAMIC CHIP 0.001uF 10% 16VC8072 1-107-820-11 CERAMIC CHIP 0.1uF 0% 16VC8073 1-119-750-11 TANTALUM CHIP 22uF 20% 6.3VC8074 1-104-851-11 TANTALUM CHIP 10uF 20% 10VC8075 1-113-985-11 TANTALUM CHIP 10uF 20% 20V
C8076 1-119-923-81 CERAMIC CHIP 0.047uF 10% 10VC8077 1-107-820-11 CERAMIC CHIP 0.1uF 0% 16VC8078 1-107-820-11 CERAMIC CHIP 0.1uF 0% 16VC8079 1-107-820-11 CERAMIC CHIP 0.1uF 0% 16VC8080 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V
C8081 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10VC8101 1-119-750-11 TANTALUM CHIP 22uF 20% 6.3VC8102 1-107-820-11 CERAMIC CHIP 0.1uF 0% 16VC8103 1-107-820-11 CERAMIC CHIP 0.1uF 0% 16VC8104 1-107-820-11 CERAMIC CHIP 0.1uF 0% 16V
C8105 1-107-820-11 CERAMIC CHIP 0.1uF 0% 16VC8106 1-107-820-11 CERAMIC CHIP 0.1uF 0% 16VC8107 1-107-820-11 CERAMIC CHIP 0.1uF 0% 16VC8108 1-107-820-11 CERAMIC CHIP 0.1uF 0% 16VC8109 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16V
C8110 1-107-820-11 CERAMIC CHIP 0.1uF 0% 16VC8111 1-107-820-11 CERAMIC CHIP 0.1uF 0% 16VC8112 1-107-820-11 CERAMIC CHIP 0.1uF 0% 16VC8113 1-107-820-11 CERAMIC CHIP 0.1uF 0% 16VC8114 1-107-820-11 CERAMIC CHIP 0.1uF 0% 16V
C8115 1-107-820-11 CERAMIC CHIP 0.1uF 0% 16VC8116 1-107-820-11 CERAMIC CHIP 0.1uF 0% 16VC8117 1-107-820-11 CERAMIC CHIP 0.1uF 0% 16VC8118 1-107-820-11 CERAMIC CHIP 0.1uF 0% 16VC8119 1-107-820-11 CERAMIC CHIP 0.1uF 0% 16V
C8120 1-107-820-11 CERAMIC CHIP 0.1uF 0% 16VC8121 1-119-750-11 TANTALUM CHIP 22uF 20% 6.3VC8123 1-107-820-11 CERAMIC CHIP 0.1uF 0% 16VC8126 1-128-964-91 TANTALUM CHIP 100uF 20% 6.3VC8127 1-107-820-11 CERAMIC CHIP 0.1uF 0% 16V
C8128 1-107-820-11 CERAMIC CHIP 0.1uF 0% 16VC8129 1-107-820-11 CERAMIC CHIP 0.1uF 0% 16VC8130 1-119-750-11 TANTALUM CHIP 22uF 20% 6.3VC8204 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10VC8208 1-104-851-11 TANTALUM CHIP 10uF 20% 10V
C8211 1-117-919-11 TANTALUM CHIP 10uF 20% 6.3VC8501 1-119-750-11 TANTALUM CHIP 22uF 20% 6.3VC8502 1-107-820-11 CERAMIC CHIP 0.1uF 0% 16VC8503 1-107-820-11 CERAMIC CHIP 0.1uF 0% 16VC8504 1-107-820-11 CERAMIC CHIP 0.1uF 0% 16V
C8506 1-164-858-11 CERAMIC CHIP 22PF 5% 16VC8507 1-107-820-11 CERAMIC CHIP 0.1uF 0% 16VC8508 1-107-820-11 CERAMIC CHIP 0.1uF 0% 16VC8510 1-107-820-11 CERAMIC CHIP 0.1uF 0% 16VC8511 1-164-858-11 CERAMIC CHIP 22PF 5% 16V
C8601 1-119-750-11 TANTALUM CHIP 22uF 20% 6.3VC8602 1-119-750-11 TANTALUM CHIP 22uF 20% 6.3VC8603 1-107-820-11 CERAMIC CHIP 0.1uF 0% 16VC8604 1-107-820-11 CERAMIC CHIP 0.1uF 0% 16VC8605 1-107-820-11 CERAMIC CHIP 0.1uF 0% 16V
C8606 1-107-820-11 CERAMIC CHIP 0.1uF 0% 16VC8607 1-107-820-11 CERAMIC CHIP 0.1uF 0% 16V
C8608 1-107-820-11 CERAMIC CHIP 0.1uF 0% 16VC8609 1-164-937-11 CERAMIC CHIP 0.001uF 10% 16VC8610 1-107-820-11 CERAMIC CHIP 0.1uF 0% 16V
C8611 1-107-820-11 CERAMIC CHIP 0.1uF 0% 16VC8612 1-107-820-11 CERAMIC CHIP 0.1uF 0% 16VC8613 1-107-820-11 CERAMIC CHIP 0.1uF 0% 16VC8614 1-107-820-11 CERAMIC CHIP 0.1uF 0% 16VC8615 1-107-820-11 CERAMIC CHIP 0.1uF 0% 16V
C8616 1-107-820-11 CERAMIC CHIP 0.1uF 0% 16VC8617 1-107-820-11 CERAMIC CHIP 0.1uF 0% 16VC8618 1-107-820-11 CERAMIC CHIP 0.1uF 0% 16VC8619 1-107-820-11 CERAMIC CHIP 0.1uF 0% 16VC8620 1-107-820-11 CERAMIC CHIP 0.1uF 0% 16V
C8621 1-107-820-11 CERAMIC CHIP 0.1uF 0% 16VC8622 1-107-820-11 CERAMIC CHIP 0.1uF 0% 16VC8623 1-107-820-11 CERAMIC CHIP 0.1uF 0% 16VC8624 1-119-750-11 TANTALUM CHIP 22uF 20% 6.3VC8701 1-119-750-11 TANTALUM CHIP 22uF 20% 6.3V
C8702 1-107-820-11 CERAMIC CHIP 0.1uF 0% 16VC8703 1-107-820-11 CERAMIC CHIP 0.1uF 0% 16VC8704 1-107-820-11 CERAMIC CHIP 0.1uF 0% 16VC8705 1-107-820-11 CERAMIC CHIP 0.1uF 0% 16VC8706 1-107-820-11 CERAMIC CHIP 0.1uF 0% 16V
C8707 1-107-820-11 CERAMIC CHIP 0.1uF 0% 16VC8708 1-107-820-11 CERAMIC CHIP 0.1uF 0% 16VC8709 1-107-820-11 CERAMIC CHIP 0.1uF 0% 16VC8710 1-107-820-11 CERAMIC CHIP 0.1uF 0% 16VC8711 1-107-820-11 CERAMIC CHIP 0.1uF 0% 16V
C8712 1-107-820-11 CERAMIC CHIP 0.1uF 0% 16VC8713 1-107-820-11 CERAMIC CHIP 0.1uF 0% 16VC8714 1-107-820-11 CERAMIC CHIP 0.1uF 0% 16VC8715 1-107-820-11 CERAMIC CHIP 0.1uF 0% 16VC8716 1-107-820-11 CERAMIC CHIP 0.1uF 0% 16V
C8717 1-107-820-11 CERAMIC CHIP 0.1uF 0% 16VC8718 1-119-750-11 TANTALUM CHIP 22uF 20% 6.3VC9101 1-164-004-11 CERAMIC CHIP 0.1uF 10% 25VC9103 1-107-820-11 CERAMIC CHIP 0.1uF 0% 16VC9104 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V
C9105 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10VC9106 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10VC9107 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16VC9108 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10VC9109 1-107-820-11 CERAMIC CHIP 0.1uF 0% 16V
C9110 1-104-916-11 TANTALUM CHIP 6.8uF 20% 20VC9111 1-104-752-11 TANTALUM CHIP 33uF 20% 6.3VC9112 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16VC9113 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10VC9114 1-117-919-11 TANTALUM CHIP 10uF 20% 6.3V
C9115 1-117-919-11 TANTALUM CHIP 10uF 20% 6.3VC9116 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10VC9117 1-164-004-11 CERAMIC CHIP 0.1uF 10% 25VC9118 1-107-819-11 CERAMIC CHIP 0.022uF 10% 16VC9119 1-135-213-21 TANTALUM CHIP 3.3uF 20% 25V
C9120 1-117-919-11 TANTALUM CHIP 10uF 20% 6.3VC9121 1-117-919-11 TANTALUM CHIP 10uF 20% 6.3VC9122 1-119-750-11 TANTALUM CHIP 22uF 20% 6.3VC9123 1-164-004-11 CERAMIC CHIP 0.1uF 10% 25VC9126 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V
MAIN
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
6-9
C9127 1-117-919-11 TANTALUM CHIP 10uF 20% 6.3VC9128 1-107-820-11 CERAMIC CHIP 0.1uF 0% 16VC9129 1-107-820-11 CERAMIC CHIP 0.1uF 0% 16VC9130 1-107-820-11 CERAMIC CHIP 0.1uF 0% 16VC9131 1-119-750-11 TANTALUM CHIP 22uF 20% 6.3V
C9132 1-107-820-11 CERAMIC CHIP 0.1uF 0% 16VC9133 1-127-772-11 CERAMIC CHIP 0.033uF 10% 16V
< CONNECTOR >
CN3001 1-778-507-21 PIN, CONNECTOR (PC BOARD) 4PCN3002 1-778-591-21 CONNECTOR, BOARD TO BOARD 30P
* CN4312 1-785-283-41 PIN, CONNECTOR (PC BOARD) 14PCN4313 1-785-283-21 PIN, CONNECTOR (PC BOARD) 14PCN4511 1-784-651-11 CONNECTOR, FFC/FPC (ZIF) 27P
CN5001 1-784-422-11 CONNECTOR, FFC/FPC (ZIF) 33PCN5002 1-778-597-21 CONNECTOR, BOARD TO BOARD 50PCN8001 1-778-595-21 CONNECTOR, BOARD TO BOARD 20PCN8002 1-573-916-11 CONNECTOR, FFC/FPC (ZIF) 7PCN8003 1-573-915-11 CONNECTOR, FFC/FPC (ZIF) 6P
CN8006 1-573-915-11 CONNECTOR, FFC/FPC (ZIF) 6PCN8007 1-778-593-21 CONNECTOR, BOARD TO BOARD 60PCN8101 1-778-803-11 CONNECTOR, BOARD TO BOARD 40P
* CN9101 1-785-481-41 CONNECTOR, BOARD TO BOARD 70P
< DIODE >
D4001 8-719-056-48 DIODE 1SS388 (TPL3)D4003 8-719-056-48 DIODE 1SS388 (TPL3)D5601 8-719-046-85 DIODE MA2S728D5602 8-719-067-36 DIODE MA3ZD1200LS0D8001 8-719-046-91 DIODE MA2S111
D8002 8-719-046-85 DIODE MA2S728D8003 8-719-046-91 DIODE MA2S111D8005 8-719-046-85 DIODE MA2S728D8006 8-719-056-48 DIODE 1SS388 (TPL3)D8007 8-719-056-48 DIODE 1SS388 (TPL3)
< FERRITE BEAD >
* FB3001 1-469-092-11 FERRITE 0uH* FB3002 1-469-092-11 FERRITE 0uH
FB8001 1-469-638-21 FERRITE 0uHFB8002 1-469-638-21 FERRITE 0uHFB8003 1-469-638-21 FERRITE 0uH
FB8004 1-469-638-21 FERRITE 0uHFB8005 1-469-638-21 FERRITE 0uHFB8006 1-469-638-21 FERRITE 0uHFB8007 1-469-638-21 FERRITE 0uHFB8008 1-469-638-21 FERRITE 0uH
FB8009 1-469-638-21 FERRITE 0uHFB8010 1-469-638-21 FERRITE 0uHFB8011 1-469-638-21 FERRITE 0uHFB8012 1-469-638-21 FERRITE 0uHFB8013 1-469-638-21 FERRITE 0uH
FB8014 1-469-638-21 FERRITE 0uHFB8015 1-469-638-21 FERRITE 0uHFB8016 1-469-638-21 FERRITE 0uHFB8017 1-469-638-21 FERRITE 0uHFB8018 1-469-638-21 FERRITE 0uH
FB8019 1-469-638-21 FERRITE 0uHFB8020 1-469-638-21 FERRITE 0uHFB8021 1-469-637-21 FERRITE 0uHFB8022 1-469-637-21 FERRITE 0uH
< FILTER >
FL4001 1-233-732-21 FILTER, BAND PASSFL4002 1-233-733-21 FILTER, LOW PASSFL5101 1-234-255-21 FILTER, LOW PASS
< IC >
IC3001 8-759-380-80 IC LA7473V-TLMIC3002 8-759-536-71 IC TLV23621PWRIC3003 8-759-488-29 IC TC7W66FU (TE12R)IC3004 8-759-584-59 IC AK4517A-VQ-LIC3005 8-759-058-58 IC TC7S04FU (TE85R)
IC3007 8-759-584-58 IC AN7535NSA-E1IC3008 8-759-649-95 IC LM4881MMXIC3009 8-752-397-21 IC CXZ31021GAIC4001 8-759-571-31 IC TK15406M-1TLIC4002 8-759-571-31 IC TK15406M-1TL
IC4003 8-759-571-32 IC TK15405M-1TLIC4004 8-759-571-31 IC TK15406M-1TLIC4005 8-759-540-53 IC BA7664FV-E2IC4006 8-759-566-06 IC TC7WH08FU (TE12R)IC4007 8-759-497-44 IC TC7WH125FU (TE12R)
IC4008 8-759-497-44 IC TC7WH125FU (TE12R)IC4009 8-759-566-06 IC TC7WH08FU (TE12R)IC4010 8-759-497-44 IC TC7WH125FU (TE12R)IC4011 8-759-497-44 IC TC7WH125FU (TE12R)IC5002 8-752-081-97 IC CXA2524R
IC5003 8-759-449-58 IC LM7131BCM5XIC5004 8-759-273-87 IC NJM2901V (TE2)IC5005 8-759-572-28 IC NJU7016RIC5006 8-759-572-28 IC NJU7016RIC5007 8-759-082-61 IC TC4W53FU
IC5008 8-759-082-58 IC TC7W08FUIC5009 8-759-572-34 IC LMV821M7XIC5010 8-759-572-34 IC LMV821M7XIC5011 8-759-572-34 IC LMV821M7XIC5012 8-759-572-34 IC LMV821M7X
IC5013 8-759-082-55 IC TC7W00FUIC5014 8-759-082-55 IC TC7W00FUIC5015 8-759-058-58 IC TC7S04FU (TE85R)IC5102 8-752-371-18 IC CXD2302QIC5201 8-759-572-38 IC NJM2140R
IC5205 8-759-572-35 IC TLC3702CPWRIC5301 8-752-397-34 IC CXD2652AGAIC5302 8-759-196-96 IC TC7SH08FU-TE85RIC5303 8-759-196-96 IC TC7SH08FU-TE85RIC5401 8-759-572-34 IC LMV821M7X
IC5402 8-759-196-96 IC TC7SH08FU-TE85RIC5403 8-752-390-38 IC CXD606-112GAIC5404 8-759-676-88 IC RU6815TC-DCMM1IC5405 8-759-449-23 IC AK93C55AV-LIC5406 8-759-559-93 IC S-8110ANP-DSB-T2
IC5407 8-759-443-08 IC TC7W241FU-TE12RIC5408 8-759-082-61 IC TC4W53FU
MAIN
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
6-10
IC5501 8-759-572-37 IC KM68V1002AT-12IC5601 8-759-482-07 IC MPC17A28SVMELIC5602 8-759-460-34 IC MPC17A36VMEL
IC5603 8-759-578-53 IC XC6365D103MRIC8001 8-759-572-52 IC HD6417709BT80AIC8002 8-759-572-70 IC KM416S4034CC-C10IC8003 8-759-572-70 IC KM416S4034CC-C10IC8004 8-759-676-89 IC HN58V1001T-25-DCMM1
IC8005 1-803-635-11 IC WTGA-EKM29U64000-K1IC8006 8-759-196-97 IC TC7SH32FU-TE85RIC8007 8-759-196-97 IC TC7SH32FU-TE85RIC8008 8-759-560-17 IC RS5C348A-E2IC8009 8-759-578-13 IC PST9329UL
IC8010 8-759-196-97 IC TC7SH32FU-TE85RIC8011 8-759-573-16 IC S-81232SG-Q4-T1IC8012 8-759-656-85 IC XC62EP3202MRIC8013 8-759-058-54 IC TC7S00FU (TE85R)IC8015 8-759-082-55 IC TC7W00FU
IC8016 8-759-195-81 IC TC7S86FUIC8020 8-759-523-11 IC TC74AC74FT (EL)IC8023 8-759-531-92 IC TC7WH04FU (TE12R)IC8024 8-759-196-96 IC TC7SH08FU-TE85RIC8025 8-759-196-96 IC TC7SH08FU-TE85R
IC8026 8-759-196-96 IC TC7SH08FU-TE85RIC8027 8-759-642-45 IC TL1596CPW-ELM2000IC8101 8-752-396-85 IC CXD702-102GAIC8102 8-759-572-71 IC KM416U4104BC-L6IC8103 8-759-572-71 IC KM416U4104BC-L6
IC8104 8-759-523-11 IC TC74AC74FT (EL)IC8202 8-759-325-27 IC TK11231AMTLIC8501 8-759-653-48 IC uPD70F3102AF1-33-FA1IC8601 8-752-396-81 IC CXD1405GGIC8602 8-759-596-11 IC KM432S2030CT-G8
IC8701 8-752-394-48 IC CXD1404GAIC8702 8-759-572-69 IC KM416U1204CC-L6IC8703 8-759-572-69 IC KM416U1204CC-L6IC9102 8-759-252-41 IC TK11900MTLIC9103 8-759-426-83 IC TK11228BMCL
IC9104 8-759-426-83 IC TK11228BMCL
< COIL >
L3001 1-414-754-11 INDUCTOR 10uHL3002 1-414-754-11 INDUCTOR 10uHL3003 1-414-398-11 INDUCTOR 10uHL3004 1-414-398-11 INDUCTOR 10uHL3005 1-414-754-11 INDUCTOR 10uH
L3006 1-414-398-11 INDUCTOR 10uHL4001 1-414-754-11 INDUCTOR 10uHL4002 1-414-754-11 INDUCTOR 10uHL4003 1-414-754-11 INDUCTOR 10uHL5001 1-414-398-11 INDUCTOR 10uH
L5002 1-414-754-11 INDUCTOR 10uHL5101 1-414-398-11 INDUCTOR 10uHL5301 1-414-754-11 INDUCTOR 10uHL5401 1-412-939-11 INDUCTOR 1uHL5402 1-414-398-11 INDUCTOR 10uH
L5403 1-410-985-42 INDUCTOR CHIP 0.22uH
L5601 1-414-407-41 INDUCTOR 330uHL5602 1-412-056-11 INDUCTOR 4.7uHL5603 1-412-056-11 INDUCTOR 4.7uHL5604 1-412-056-11 INDUCTOR 4.7uH
L5605 1-412-056-11 INDUCTOR 4.7uHL5606 1-410-389-31 INDUCTOR CHIP 47uHL5607 1-410-389-31 INDUCTOR CHIP 47uHL5610 1-416-346-11 INDUCTOR 33uHL8001 1-414-754-11 INDUCTOR 10uH
L8002 1-414-754-11 INDUCTOR 10uHL8003 1-414-398-11 INDUCTOR 10uHL8004 1-414-394-41 INDUCTOR 2.2uHL8101 1-412-028-11 INDUCTOR CHIP 4.7uHL8102 1-414-754-11 INDUCTOR 10uH
L8103 1-414-754-11 INDUCTOR 10uHL8104 1-414-398-11 INDUCTOR 10uHL8202 1-414-754-11 INDUCTOR 10uHL8501 1-469-367-21 INDUCTOR 10uHL8601 1-414-398-11 INDUCTOR 10uH
L8602 1-414-398-11 INDUCTOR 10uHL8603 1-414-398-11 INDUCTOR 10uHL8701 1-469-367-21 INDUCTOR 10uHL8702 1-414-398-11 INDUCTOR 10uHL9102 1-414-404-41 INDUCTOR 100uH
L9103 1-414-404-41 INDUCTOR 100uHL9104 1-414-398-11 INDUCTOR 10uHL9105 1-414-398-11 INDUCTOR 10uH
< TRANSISTOR >
Q3001 8-759-426-37 TRANSISTOR MC68HC05G6PB-SC430917PB
Q3002 8-729-037-52 TRANSISTOR 2SD2216J-QR (TX).SOQ3003 8-729-047-37 TRANSISTOR FDN338PQ3004 8-729-047-68 TRANSISTOR SSM3K03FE (TPL3)Q4001 8-729-037-53 TRANSISTOR 2SB1462J-QR (TX).SO
Q4002 8-729-037-53 TRANSISTOR 2SB1462J-QR (TX).SOQ4003 8-729-037-67 TRANSISTOR UN9119J- (TX).SOQ4004 8-729-037-74 TRANSISTOR UN9213J- (TX).SOQ4005 8-729-427-70 TRANSISTOR XP4401Q4006 8-729-427-70 TRANSISTOR XP4401
Q4007 8-729-427-70 TRANSISTOR XP4401Q5001 8-729-429-50 TRANSISTOR XP4312Q5002 8-729-037-89 TRANSISTOR 2SC4627J-C (TX).SOQ5003 8-729-047-36 TRANSISTOR CPH3303-TLQ5004 8-729-037-73 TRANSISTOR UN9212J- (TX).SO
Q5005 8-729-426-22 TRANSISTOR XP1211Q5009 8-729-047-36 TRANSISTOR CPH3303-TLQ5010 8-729-037-73 TRANSISTOR UN9212J- (TX).SOQ5101 8-729-427-74 TRANSISTOR XP4601Q5102 8-729-047-36 TRANSISTOR CPH3303-TL
Q5201 8-729-427-72 TRANSISTOR XP4501Q5202 8-729-427-70 TRANSISTOR XP4401Q5203 8-729-047-36 TRANSISTOR CPH3303-TLQ5204 8-729-037-73 TRANSISTOR UN9212J- (TX).SOQ5601 8-729-047-90 TRANSISTOR XP162A11C0PR
Q5602 8-729-037-61 TRANSISTOR UN9113J- (TX).SOQ5603 8-729-037-73 TRANSISTOR UN9212J- (TX).SOQ8001 8-729-037-53 TRANSISTOR 2SB1462J-QR (TX).SO
MAIN
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
6-11
Q8002 8-729-043-94 TRANSISTOR CPH3106-PM-TLQ8003 8-729-044-20 TRANSISTOR SI6463DQ-T1
Q8004 8-729-044-20 TRANSISTOR SI6463DQ-T1Q8005 8-729-037-53 TRANSISTOR 2SB1462J-QR (TX).SOQ8006 8-729-047-68 TRANSISTOR SSM3K03FE (TPL3)Q8007 8-729-044-20 TRANSISTOR SI6463DQ-T1Q8008 8-729-044-20 TRANSISTOR SI6463DQ-T1
Q8009 8-729-047-68 TRANSISTOR SSM3K03FE (TPL3)Q8010 8-729-032-62 TRANSISTOR 2SJ347-TE85LQ8011 8-729-032-62 TRANSISTOR 2SJ347-TE85LQ8012 8-729-047-68 TRANSISTOR SSM3K03FE (TPL3)Q8013 8-729-047-68 TRANSISTOR SSM3K03FE (TPL3)
Q8014 8-729-047-68 TRANSISTOR SSM3K03FE (TPL3)Q9101 8-729-427-72 TRANSISTOR XP4501Q9102 8-729-037-52 TRANSISTOR 2SD2216J-QR (TX).SOQ9103 8-729-047-68 TRANSISTOR SSM3K03FE (TPL3)Q9104 8-729-427-70 TRANSISTOR XP4401
Q9105 8-729-041-23 TRANSISTOR NDS356APQ9107 8-729-047-37 TRANSISTOR FDN338PQ9108 8-729-047-68 TRANSISTOR SSM3K03FE (TPL3)Q9110 8-729-047-68 TRANSISTOR SSM3K03FE (TPL3)Q9111 8-729-427-70 TRANSISTOR XP4401
Q9112 8-729-047-68 TRANSISTOR SSM3K03FE (TPL3)Q9113 8-729-047-68 TRANSISTOR SSM3K03FE (TPL3)Q9115 8-729-042-82 TRANSISTOR NDH834PQ9116 8-729-047-68 TRANSISTOR SSM3K03FE (TPL3)Q9117 8-729-041-23 TRANSISTOR NDS356AP
Q9122 8-729-047-37 TRANSISTOR FDN338PQ9125 8-729-037-74 TRANSISTOR UN9213J- (TX).SOQ9126 8-729-032-62 TRANSISTOR 2SJ347-TE85L
< RESISTOR >
R1001 1-218-963-11 RES, CHIP 6.8K 5% 1/16WR1002 1-218-957-11 RES, CHIP 2.2K 5% 1/16WR1003 1-218-959-11 RES, CHIP 3.3K 5% 1/16WR1004 1-218-947-11 RES, CHIP 330 5% 1/16WR1005 1-218-965-11 RES, CHIP 10K 5% 1/16W
R1006 1-218-963-11 RES, CHIP 6.8K 5% 1/16WR1007 1-218-963-11 RES, CHIP 6.8K 5% 1/16WR1008 1-218-971-11 RES, CHIP 33K 5% 1/16WR1009 1-218-971-11 RES, CHIP 33K 5% 1/16WR1010 1-218-969-11 RES, CHIP 22K 5% 1/16W
R1011 1-218-971-11 RES, CHIP 33K 5% 1/16WR1012 1-218-969-11 RES, CHIP 22K 5% 1/16WR1013 1-218-961-11 RES, CHIP 4.7K 5% 1/16WR1014 1-218-963-11 RES, CHIP 6.8K 5% 1/16WR1015 1-218-973-11 RES, CHIP 47K 5% 1/16W
R1016 1-208-691-11 METAL CHIP 2.2K 0.5% 1/16WR1017 1-208-927-11 METAL CHIP 47K 0.5% 1/16WR1019 1-218-990-11 SHORT 0R1021 1-208-927-11 METAL CHIP 47K 0.5% 1/16WR1022 1-218-965-11 RES, CHIP 10K 5% 1/16W
R1023 1-218-965-11 RES, CHIP 10K 5% 1/16WR1024 1-208-927-11 METAL CHIP 47K 0.5% 1/16WR1025 1-218-446-11 METAL CHIP 1 5% 1/16WR1026 1-218-990-11 SHORT 0R1027 1-218-849-11 METAL CHIP 3.3K 0.5% 1/16W
R1028 1-218-975-11 RES, CHIP 68K 5% 1/16WR1029 1-218-973-11 RES, CHIP 47K 5% 1/16WR1030 1-208-675-11 METAL CHIP 470 0.5% 1/16WR1032 1-218-955-11 RES, CHIP 1.5K 5% 1/16WR2001 1-218-963-11 RES, CHIP 6.8K 5% 1/16W
R2002 1-218-957-11 RES, CHIP 2.2K 5% 1/16WR2003 1-218-959-11 RES, CHIP 3.3K 5% 1/16WR2004 1-218-947-11 RES, CHIP 330 5% 1/16WR2005 1-218-965-11 RES, CHIP 10K 5% 1/16WR2006 1-218-963-11 RES, CHIP 6.8K 5% 1/16W
R2007 1-218-963-11 RES, CHIP 6.8K 5% 1/16WR2008 1-218-971-11 RES, CHIP 33K 5% 1/16WR2009 1-218-971-11 RES, CHIP 33K 5% 1/16WR2010 1-218-969-11 RES, CHIP 22K 5% 1/16WR2011 1-218-971-11 RES, CHIP 33K 5% 1/16W
R2012 1-218-969-11 RES, CHIP 22K 5% 1/16WR2013 1-218-961-11 RES, CHIP 4.7K 5% 1/16WR2014 1-218-963-11 RES, CHIP 6.8K 5% 1/16WR2015 1-218-973-11 RES, CHIP 47K 5% 1/16WR2016 1-208-691-11 METAL CHIP 2.2K 0.5% 1/16W
R2017 1-208-927-11 METAL CHIP 47K 0.5% 1/16WR2019 1-218-990-11 SHORT 0R2021 1-208-927-11 METAL CHIP 47K 0.5% 1/16WR2022 1-218-965-11 RES, CHIP 10K 5% 1/16WR2023 1-218-965-11 RES, CHIP 10K 5% 1/16W
R2024 1-208-927-11 METAL CHIP 47K 0.5% 1/16WR2025 1-218-446-11 METAL CHIP 1 5% 1/16WR2026 1-218-990-11 SHORT 0R2027 1-218-849-11 METAL CHIP 3.3K 0.5% 1/16WR2028 1-218-975-11 RES, CHIP 68K 5% 1/16W
R2029 1-218-973-11 RES, CHIP 47K 5% 1/16WR2030 1-208-675-11 METAL CHIP 470 0.5% 1/16WR2032 1-218-955-11 RES, CHIP 1.5K 5% 1/16WR3001 1-218-981-11 RES, CHIP 220K 5% 1/16WR3002 1-216-150-91 RES, CHIP 10 5% 1/8W
R3004 1-218-977-11 RES, CHIP 100K 5% 1/16WR3005 1-218-989-11 RES, CHIP 1M 5% 1/16WR3006 1-218-446-11 METAL CHIP 1 5% 1/16WR3009 1-218-965-11 RES, CHIP 10K 5% 1/16WR3010 1-218-965-11 RES, CHIP 10K 5% 1/16W
R3011 1-218-969-11 RES, CHIP 22K 5% 1/16WR3013 1-218-979-11 RES, CHIP 150K 5% 1/16WR3014 1-218-989-11 RES, CHIP 1M 5% 1/16WR3015 1-218-989-11 RES, CHIP 1M 5% 1/16WR3016 1-218-965-11 RES, CHIP 10K 5% 1/16W
R3018 1-218-975-11 RES, CHIP 68K 5% 1/16WR3019 1-218-969-11 RES, CHIP 22K 5% 1/16WR3022 1-218-990-11 SHORT 0R3023 1-218-983-11 RES, CHIP 330K 5% 1/16WR4001 1-218-941-11 METAL CHIP 100 0.5% 1/16W
R4002 1-208-671-11 METAL CHIP 330 0.5% 1/16WR4003 1-208-683-11 METAL CHIP 1K 0.5% 1/16WR4004 1-208-683-11 METAL CHIP 1K 0.5% 1/16WR4005 1-218-957-11 RES, CHIP 2.2K 5% 1/16WR4006 1-218-941-11 METAL CHIP 100 0.5% 1/16W
R4007 1-208-671-11 METAL CHIP 330 0.5% 1/16WR4008 1-208-683-11 METAL CHIP 1K 0.5% 1/16WR4009 1-208-683-11 METAL CHIP 1K 0.5% 1/16W
MAIN
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
6-12
R4010 1-218-957-11 RES, CHIP 2.2K 5% 1/16WR4011 1-208-675-11 METAL CHIP 470 0.5% 1/16W
R4012 1-218-941-11 METAL CHIP 100 0.5% 1/16WR4013 1-218-957-11 RES, CHIP 2.2K 5% 1/16WR4014 1-218-957-11 RES, CHIP 2.2K 5% 1/16WR4015 1-218-957-11 RES, CHIP 2.2K 5% 1/16WR4016 1-218-957-11 RES, CHIP 2.2K 5% 1/16W
R4017 1-218-957-11 RES, CHIP 2.2K 5% 1/16WR4018 1-218-957-11 RES, CHIP 2.2K 5% 1/16WR4019 1-218-990-11 SHORT 0R4020 1-218-990-11 SHORT 0R4021 1-218-990-11 SHORT 0
R4022 1-218-990-11 SHORT 0R4026 1-218-985-11 RES, CHIP 470K 5% 1/16WR4028 1-218-985-11 RES, CHIP 470K 5% 1/16WR4030 1-218-965-11 RES, CHIP 10K 5% 1/16WR4031 1-218-965-11 RES, CHIP 10K 5% 1/16W
R5001 1-218-945-11 RES, CHIP 220 5% 1/16WR5003 1-218-985-11 RES, CHIP 470K 5% 1/16WR5004 1-218-957-11 RES, CHIP 2.2K 5% 1/16WR5005 1-218-957-11 RES, CHIP 2.2K 5% 1/16WR5006 1-218-987-11 RES, CHIP 680K 5% 1/16W
R5007 1-218-973-11 RES, CHIP 47K 5% 1/16WR5008 1-218-973-11 RES, CHIP 47K 5% 1/16WR5009 1-218-953-11 RES, CHIP 1K 5% 1/16WR5010 1-218-965-11 RES, CHIP 10K 5% 1/16WR5011 1-218-987-11 RES, CHIP 680K 5% 1/16W
R5012 1-218-977-11 RES, CHIP 100K 5% 1/16WR5013 1-218-957-11 RES, CHIP 2.2K 5% 1/16WR5014 1-218-977-11 RES, CHIP 100K 5% 1/16WR5015 1-218-965-11 RES, CHIP 10K 5% 1/16WR5016 1-218-953-11 RES, CHIP 1K 5% 1/16W
R5017 1-218-949-11 RES, CHIP 470 5% 1/16WR5018 1-218-949-11 RES, CHIP 470 5% 1/16WR5020 1-218-951-11 RES, CHIP 680 5% 1/16WR5021 1-218-951-11 RES, CHIP 680 5% 1/16WR5022 1-218-990-11 SHORT 0
R5023 1-218-953-11 RES, CHIP 1K 5% 1/16WR5024 1-218-965-11 RES, CHIP 10K 5% 1/16WR5025 1-218-981-11 RES, CHIP 220K 5% 1/16WR5026 1-218-977-11 RES, CHIP 100K 5% 1/16WR5027 1-218-975-11 RES, CHIP 68K 5% 1/16W
R5028 1-218-965-11 RES, CHIP 10K 5% 1/16WR5030 1-218-965-11 RES, CHIP 10K 5% 1/16WR5031 1-218-965-11 RES, CHIP 10K 5% 1/16WR5032 1-218-977-11 RES, CHIP 100K 5% 1/16WR5033 1-218-977-11 RES, CHIP 100K 5% 1/16W
R5034 1-218-953-11 RES, CHIP 1K 5% 1/16WR5037 1-218-985-11 RES, CHIP 470K 5% 1/16WR5038 1-218-985-11 RES, CHIP 470K 5% 1/16WR5039 1-218-967-11 RES, CHIP 15K 5% 1/16WR5040 1-218-967-11 RES, CHIP 15K 5% 1/16W
R5041 1-218-965-11 RES, CHIP 10K 5% 1/16WR5042 1-218-967-11 RES, CHIP 15K 5% 1/16WR5043 1-218-965-11 RES, CHIP 10K 5% 1/16WR5044 1-218-985-11 RES, CHIP 470K 5% 1/16WR5045 1-218-965-11 RES, CHIP 10K 5% 1/16W
R5046 1-218-985-11 RES, CHIP 470K 5% 1/16WR5047 1-218-965-11 RES, CHIP 10K 5% 1/16WR5048 1-218-965-11 RES, CHIP 10K 5% 1/16WR5049 1-218-973-11 RES, CHIP 47K 5% 1/16WR5050 1-218-973-11 RES, CHIP 47K 5% 1/16W
R5051 1-218-961-11 RES, CHIP 4.7K 5% 1/16WR5052 1-218-977-11 RES, CHIP 100K 5% 1/16WR5053 1-218-977-11 RES, CHIP 100K 5% 1/16WR5054 1-218-973-11 RES, CHIP 47K 5% 1/16WR5055 1-218-977-11 RES, CHIP 100K 5% 1/16W
R5056 1-218-977-11 RES, CHIP 100K 5% 1/16WR5057 1-218-973-11 RES, CHIP 47K 5% 1/16WR5058 1-218-977-11 RES, CHIP 100K 5% 1/16WR5059 1-218-990-11 SHORT 0R5060 1-218-990-11 SHORT 0
R5061 1-218-990-11 SHORT 0R5076 1-218-989-11 RES, CHIP 1M 5% 1/16WR5077 1-218-989-11 RES, CHIP 1M 5% 1/16WR5078 1-218-957-11 RES, CHIP 2.2K 5% 1/16WR5101 1-218-953-11 RES, CHIP 1K 5% 1/16W
R5102 1-218-953-11 RES, CHIP 1K 5% 1/16WR5103 1-218-941-11 RES, CHIP 100 5% 1/16WR5104 1-218-953-11 RES, CHIP 1K 5% 1/16WR5105 1-218-953-11 RES, CHIP 1K 5% 1/16WR5106 1-218-989-11 RES, CHIP 1M 5% 1/16W
R5107 1-218-989-11 RES, CHIP 1M 5% 1/16WR5112 1-218-981-11 RES, CHIP 220K 5% 1/16WR5113 1-218-977-11 RES, CHIP 100K 5% 1/16WR5201 1-218-953-11 RES, CHIP 1K 5% 1/16WR5202 1-218-953-11 RES, CHIP 1K 5% 1/16W
R5203 1-218-953-11 RES, CHIP 1K 5% 1/16WR5204 1-218-953-11 RES, CHIP 1K 5% 1/16WR5205 1-218-971-11 RES, CHIP 33K 5% 1/16WR5206 1-218-971-11 RES, CHIP 33K 5% 1/16WR5207 1-218-977-11 RES, CHIP 100K 5% 1/16W
R5208 1-218-977-11 RES, CHIP 100K 5% 1/16WR5209 1-218-977-11 RES, CHIP 100K 5% 1/16WR5210 1-218-977-11 RES, CHIP 100K 5% 1/16WR5211 1-218-981-11 RES, CHIP 220K 5% 1/16WR5214 1-218-989-11 RES, CHIP 1M 5% 1/16W
R5215 1-218-989-11 RES, CHIP 1M 5% 1/16WR5216 1-218-990-11 SHORT 0 5% 1/16WR5217 1-218-990-11 SHORT 0 5% 1/16WR5301 1-218-935-11 RES, CHIP 33 5% 1/16WR5302 1-218-959-11 RES, CHIP 3.3K 5% 1/16W
R5303 1-218-965-11 RES, CHIP 10K 5% 1/16WR5304 1-218-971-11 RES, CHIP 33K 5% 1/16WR5305 1-218-989-11 RES, CHIP 1M 5% 1/16WR5306 1-218-975-11 RES, CHIP 68K 5% 1/16WR5307 1-218-975-11 RES, CHIP 68K 5% 1/16W
R5308 1-218-961-11 RES, CHIP 4.7K 5% 1/16WR5309 1-218-985-11 RES, CHIP 470K 5% 1/16WR5310 1-218-961-11 RES, CHIP 4.7K 5% 1/16WR5311 1-218-977-11 RES, CHIP 100K 5% 1/16WR5312 1-218-965-11 RES, CHIP 10K 5% 1/16W
R5313 1-216-801-11 METAL CHIP 22 5% 1/16WR5314 1-218-937-11 RES, CHIP 47 5% 1/16WR5316 1-218-959-11 RES, CHIP 3.3K 5% 1/16W
MAIN
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
6-13
R5318 1-218-990-11 SHORT 0R5401 1-218-965-11 RES, CHIP 10K 5% 1/16W
R5402 1-218-965-11 RES, CHIP 10K 5% 1/16WR5403 1-218-983-11 RES, CHIP 330K 5% 1/16WR5404 1-218-983-11 RES, CHIP 330K 5% 1/16WR5405 1-218-983-11 RES, CHIP 330K 5% 1/16WR5406 1-218-983-11 RES, CHIP 330K 5% 1/16W
R5407 1-218-983-11 RES, CHIP 330K 5% 1/16WR5408 1-218-983-11 RES, CHIP 330K 5% 1/16WR5409 1-208-707-11 METAL CHIP 10K 0.5% 1/16WR5410 1-208-719-11 METAL CHIP 33K 0.5% 1/16WR5411 1-218-973-11 RES, CHIP 47K 5% 1/16W
R5412 1-218-985-11 RES, CHIP 470K 5% 1/16WR5413 1-218-983-11 RES, CHIP 330K 5% 1/16WR5414 1-218-983-11 RES, CHIP 330K 5% 1/16WR5416 1-208-663-11 METAL CHIP 150 0.5% 1/16WR5417 1-218-937-11 RES, CHIP 47 5% 1/16W
R5418 1-218-983-11 RES, CHIP 330K 5% 1/16WR5419 1-218-989-11 RES, CHIP 1M 5% 1/16WR5420 1-218-939-11 RES, CHIP 68 5% 1/16WR5421 1-218-989-11 RES, CHIP 1M 5% 1/16WR5422 1-218-990-11 SHORT 0
R5423 1-218-990-11 SHORT 0R5424 1-218-985-11 RES, CHIP 470K 5% 1/16WR5425 1-218-990-11 SHORT 0R5426 1-218-941-11 METAL CHIP 100 0.5% 1/16WR5427 1-218-941-11 METAL CHIP 100 0.5% 1/16W
R5428 1-218-941-11 METAL CHIP 100 0.5% 1/16WR5429 1-218-941-11 METAL CHIP 100 0.5% 1/16WR5601 1-218-990-11 SHORT 0R5602 1-218-977-11 RES, CHIP 100K 5% 1/16WR5603 1-218-985-11 RES, CHIP 470K 5% 1/16W
R5604 1-218-989-11 RES, CHIP 1M 5% 1/16WR5605 1-218-990-11 SHORT 0R5606 1-218-983-11 RES, CHIP 330K 5% 1/16WR5607 1-218-990-11 SHORT 0R8001 1-218-977-11 RES, CHIP 100K 5% 1/16W
R8002 1-218-953-11 RES, CHIP 1K 5% 1/16WR8003 1-218-953-11 RES, CHIP 1K 5% 1/16WR8004 1-218-953-11 RES, CHIP 1K 5% 1/16WR8005 1-218-953-11 RES, CHIP 1K 5% 1/16WR8006 1-218-953-11 RES, CHIP 1K 5% 1/16W
R8007 1-218-985-11 RES, CHIP 470K 5% 1/16WR8008 1-218-985-11 RES, CHIP 470K 5% 1/16WR8009 1-218-985-11 RES, CHIP 470K 5% 1/16WR8010 1-218-985-11 RES, CHIP 470K 5% 1/16WR8011 1-218-985-11 RES, CHIP 470K 5% 1/16W
R8012 1-218-977-11 RES, CHIP 100K 5% 1/16WR8013 1-218-977-11 RES, CHIP 100K 5% 1/16WR8015 1-218-985-11 RES, CHIP 470K 5% 1/16WR8016 1-218-953-11 RES, CHIP 1K 5% 1/16WR8017 1-218-985-11 RES, CHIP 470K 5% 1/16W
R8018 1-218-953-11 RES, CHIP 1K 5% 1/16WR8019 1-218-953-11 RES, CHIP 1K 5% 1/16WR8020 1-218-985-11 RES, CHIP 470K 5% 1/16WR8021 1-218-953-11 RES, CHIP 1K 5% 1/16WR8022 1-218-985-11 RES, CHIP 470K 5% 1/16W
R8023 1-218-953-11 RES, CHIP 1K 5% 1/16WR8024 1-218-985-11 RES, CHIP 470K 5% 1/16WR8025 1-218-953-11 RES, CHIP 1K 5% 1/16WR8026 1-218-985-11 RES, CHIP 470K 5% 1/16WR8027 1-218-953-11 RES, CHIP 1K 5% 1/16W
R8028 1-218-985-11 RES, CHIP 470K 5% 1/16WR8029 1-218-953-11 RES, CHIP 1K 5% 1/16WR8030 1-218-985-11 RES, CHIP 470K 5% 1/16WR8031 1-218-953-11 RES, CHIP 1K 5% 1/16WR8032 1-218-985-11 RES, CHIP 470K 5% 1/16W
R8033 1-218-953-11 RES, CHIP 1K 5% 1/16WR8034 1-218-941-11 RES, CHIP 100 5% 1/16WR8035 1-218-941-11 RES, CHIP 100 5% 1/16WR8036 1-218-983-11 RES, CHIP 330K 5% 1/16WR8037 1-218-965-11 RES, CHIP 10K 5% 1/16W
R8038 1-218-953-11 RES, CHIP 1K 5% 1/16WR8039 1-218-977-11 RES, CHIP 100K 5% 1/16WR8040 1-218-985-11 RES, CHIP 470K 5% 1/16WR8041 1-218-985-11 RES, CHIP 470K 5% 1/16WR8042 1-208-955-11 METAL CHIP 680K 0.5% 1/16W
R8043 1-208-955-11 METAL CHIP 680K 0.5% 1/16WR8044 1-218-990-11 SHORT 0R8045 1-218-983-11 RES, CHIP 330K 5% 1/16WR8046 1-218-961-11 RES, CHIP 4.7K 5% 1/16WR8047 1-218-953-11 RES, CHIP 1K 5% 1/16W
R8048 1-216-304-11 METAL CHIP 3.3 5% 1/10WR8049 1-216-304-11 METAL CHIP 3.3 5% 1/10WR8050 1-218-941-11 RES, CHIP 100 5% 1/16WR8051 1-218-973-11 RES, CHIP 47K 5% 1/16WR8052 1-218-953-11 RES, CHIP 1K 5% 1/16W
R8053 1-218-983-11 RES, CHIP 330K 5% 1/16WR8055 1-218-977-11 RES, CHIP 100K 5% 1/16WR8056 1-218-945-11 RES, CHIP 220 5% 1/16WR8057 1-218-965-11 RES, CHIP 10K 5% 1/16WR8058 1-218-985-11 RES, CHIP 470K 5% 1/16W
R8061 1-218-989-11 RES, CHIP 1M 5% 1/16WR8062 1-218-983-11 RES, CHIP 330K 5% 1/16WR8063 1-218-990-11 SHORT 0R8064 1-218-990-11 SHORT 0R8065 1-218-990-11 SHORT 0
R8066 1-218-990-11 SHORT 0R8067 1-218-990-11 SHORT 0R8068 1-218-990-11 SHORT 0R8069 1-218-990-11 SHORT 0R8070 1-218-990-11 SHORT 0
R8071 1-218-990-11 SHORT 0R8072 1-218-990-11 SHORT 0R8073 1-218-990-11 SHORT 0R8074 1-218-990-11 SHORT 0R8075 1-218-990-11 SHORT 0
R8076 1-218-990-11 SHORT 0R8077 1-218-990-11 SHORT 0R8078 1-218-990-11 SHORT 0R8079 1-218-990-11 SHORT 0R8080 1-218-990-11 SHORT 0
R8081 1-218-990-11 SHORT 0R8082 1-218-990-11 SHORT 0R8083 1-218-977-11 RES, CHIP 100K 5% 1/16W
MAIN
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
6-14
R8084 1-218-990-11 SHORT 0R8085 1-218-983-11 RES, CHIP 330K 5% 1/16W
R8086 1-218-983-11 RES, CHIP 330K 5% 1/16WR8087 1-218-983-11 RES, CHIP 330K 5% 1/16WR8088 1-218-983-11 RES, CHIP 330K 5% 1/16WR8089 1-218-983-11 RES, CHIP 330K 5% 1/16WR8090 1-218-983-11 RES, CHIP 330K 5% 1/16W
R8091 1-218-983-11 RES, CHIP 330K 5% 1/16WR8092 1-218-983-11 RES, CHIP 330K 5% 1/16WR8093 1-218-983-11 RES, CHIP 330K 5% 1/16WR8094 1-218-983-11 RES, CHIP 330K 5% 1/16WR8095 1-218-983-11 RES, CHIP 330K 5% 1/16W
R8096 1-218-983-11 RES, CHIP 330K 5% 1/16WR8097 1-218-985-11 RES, CHIP 470K 5% 1/16WR8098 1-218-953-11 RES, CHIP 1K 5% 1/16WR8099 1-218-983-11 RES, CHIP 330K 5% 1/16WR8101 1-218-945-11 METAL CHIP 220 0.5% 1/16W
R8102 1-208-671-11 METAL CHIP 330 0.5% 1/16WR8103 1-208-679-11 METAL CHIP 680 0.5% 1/16WR8104 1-208-683-11 METAL CHIP 1K 0.5% 1/16WR8105 1-208-691-11 METAL CHIP 2.2K 0.5% 1/16WR8106 1-208-683-11 METAL CHIP 1K 0.5% 1/16W
R8107 1-218-945-11 METAL CHIP 220 0.5% 1/16WR8108 1-218-945-11 METAL CHIP 220 0.5% 1/16WR8109 1-218-990-11 SHORT 0R8110 1-218-990-11 SHORT 0R8111 1-218-977-11 RES, CHIP 100K 5% 1/16W
R8112 1-218-977-11 RES, CHIP 100K 5% 1/16WR8113 1-218-977-11 RES, CHIP 100K 5% 1/16WR8114 1-218-977-11 RES, CHIP 100K 5% 1/16WR8115 1-218-977-11 RES, CHIP 100K 5% 1/16WR8116 1-218-977-11 RES, CHIP 100K 5% 1/16W
R8117 1-218-977-11 RES, CHIP 100K 5% 1/16WR8118 1-218-977-11 RES, CHIP 100K 5% 1/16WR8119 1-218-977-11 RES, CHIP 100K 5% 1/16WR8120 1-218-977-11 RES, CHIP 100K 5% 1/16WR8121 1-218-977-11 RES, CHIP 100K 5% 1/16W
R8122 1-218-977-11 RES, CHIP 100K 5% 1/16WR8125 1-218-990-11 SHORT 0R8126 1-218-990-11 SHORT 0R8127 1-208-683-11 METAL CHIP 1K 0.5% 1/16WR8129 1-218-977-11 RES, CHIP 100K 5% 1/16W
R8130 1-218-977-11 RES, CHIP 100K 5% 1/16WR8208 1-208-679-11 METAL CHIP 680 0.5% 1/16WR8501 1-218-961-11 RES, CHIP 4.7K 5% 1/16WR8502 1-218-961-11 RES, CHIP 4.7K 5% 1/16WR8503 1-218-961-11 RES, CHIP 4.7K 5% 1/16W
R8504 1-218-961-11 RES, CHIP 4.7K 5% 1/16WR8505 1-218-961-11 RES, CHIP 4.7K 5% 1/16WR8506 1-218-961-11 RES, CHIP 4.7K 5% 1/16WR8507 1-218-961-11 RES, CHIP 4.7K 5% 1/16WR8508 1-218-965-11 RES, CHIP 10K 5% 1/16W
R8509 1-218-965-11 RES, CHIP 10K 5% 1/16WR8510 1-218-965-11 RES, CHIP 10K 5% 1/16WR8511 1-218-965-11 RES, CHIP 10K 5% 1/16WR8512 1-218-977-11 RES, CHIP 100K 5% 1/16WR8513 1-218-977-11 RES, CHIP 100K 5% 1/16W
R8514 1-218-977-11 RES, CHIP 100K 5% 1/16WR8515 1-218-977-11 RES, CHIP 100K 5% 1/16WR8516 1-218-977-11 RES, CHIP 100K 5% 1/16WR8517 1-218-977-11 RES, CHIP 100K 5% 1/16WR8519 1-218-977-11 RES, CHIP 100K 5% 1/16W
R8520 1-218-949-11 RES, CHIP 470 5% 1/16WR8521 1-218-977-11 RES, CHIP 100K 5% 1/16WR8522 1-218-985-11 RES, CHIP 470K 5% 1/16WR8523 1-218-985-11 RES, CHIP 470K 5% 1/16WR8524 1-218-989-11 RES, CHIP 1M 5% 1/16W
R8525 1-218-989-11 RES, CHIP 1M 5% 1/16WR8526 1-218-977-11 RES, CHIP 100K 5% 1/16WR8527 1-218-985-11 RES, CHIP 470K 5% 1/16WR8528 1-218-985-11 RES, CHIP 470K 5% 1/16WR8529 1-218-961-11 RES, CHIP 4.7K 5% 1/16W
R8530 1-218-977-11 RES, CHIP 100K 5% 1/16WR8531 1-218-977-11 RES, CHIP 100K 5% 1/16WR8532 1-218-977-11 RES, CHIP 100K 5% 1/16WR8601 1-218-987-11 RES, CHIP 680K 5% 1/16WR8602 1-218-990-11 SHORT 0
R8603 1-218-990-11 SHORT 0R8901 1-218-977-11 RES, CHIP 100K 5% 1/16WR8902 1-218-977-11 RES, CHIP 100K 5% 1/16WR8903 1-218-977-11 RES, CHIP 100K 5% 1/16WR8904 1-218-990-11 SHORT 0
R8906 1-218-957-11 RES, CHIP 2.2K 5% 1/16WR8908 1-218-977-11 RES, CHIP 100K 5% 1/16WR8909 1-218-937-11 RES, CHIP 47 5% 1/16WR8910 1-218-959-11 RES, CHIP 3.3K 5% 1/16WR8911 1-218-985-11 RES, CHIP 470K 5% 1/16W
R8912 1-218-965-11 RES, CHIP 10K 5% 1/16WR8913 1-218-965-11 RES, CHIP 10K 5% 1/16WR8914 1-218-989-11 RES, CHIP 1M 5% 1/16WR8915 1-216-304-11 METAL CHIP 3.3 5% 1/10WR8916 1-218-949-11 RES, CHIP 470 5% 1/16W
R8917 1-218-977-11 RES, CHIP 100K 5% 1/16WR8918 1-218-965-11 RES, CHIP 10K 5% 1/16WR8919 1-218-990-11 SHORT 0R8921 1-218-990-11 SHORT 0R8931 1-218-967-11 RES, CHIP 15K 5% 1/16W
R8932 1-218-965-11 RES, CHIP 10K 5% 1/16WR8933 1-218-989-11 RES, CHIP 1M 5% 1/16WR8934 1-218-965-11 RES, CHIP 10K 5% 1/16WR8935 1-218-977-11 RES, CHIP 100K 5% 1/16WR8936 1-218-959-11 RES, CHIP 3.3K 5% 1/16W
R8937 1-218-989-11 RES, CHIP 1M 5% 1/16WR9101 1-208-947-11 METAL CHIP 330K 0.5% 1/16WR9102 1-208-927-11 METAL CHIP 47K 0.5% 1/16WR9103 1-208-691-11 METAL CHIP 2.2K 0.5% 1/16WR9104 1-218-969-11 RES, CHIP 22K 5% 1/16W
R9105 1-218-977-11 RES, CHIP 100K 5% 1/16WR9106 1-218-989-11 RES, CHIP 1M 5% 1/16WR9107 1-218-989-11 RES, CHIP 1M 5% 1/16WR9108 1-218-979-11 RES, CHIP 150K 5% 1/16WR9109 1-218-990-11 SHORT 0
R9110 1-218-989-11 RES, CHIP 1M 5% 1/16WR9111 1-218-981-11 RES, CHIP 220K 5% 1/16WR9112 1-218-977-11 RES, CHIP 100K 5% 1/16W
MAIN
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
6-15
MAIN POWER
R9113 1-218-989-11 RES, CHIP 1M 5% 1/16WR9114 1-218-989-11 RES, CHIP 1M 5% 1/16W
R9116 1-218-973-11 RES, CHIP 47K 5% 1/16WR9117 1-218-990-11 SHORT 0R9118 1-208-947-11 METAL CHIP 330K 0.5% 1/16WR9119 1-208-947-11 METAL CHIP 330K 0.5% 1/16WR9120 1-218-989-11 RES, CHIP 1M 5% 1/16W
R9121 1-218-990-11 SHORT 0R9123 1-218-977-11 RES, CHIP 100K 5% 1/16WR9124 1-218-989-11 RES, CHIP 1M 5% 1/16WR9125 1-218-989-11 RES, CHIP 1M 5% 1/16WR9126 1-218-977-11 RES, CHIP 100K 5% 1/16W
R9127 1-218-977-11 RES, CHIP 100K 5% 1/16WR9128 1-218-989-11 RES, CHIP 1M 5% 1/16WR9129 1-218-989-11 RES, CHIP 1M 5% 1/16WR9130 1-218-990-11 SHORT 0R9132 1-218-989-11 RES, CHIP 1M 5% 1/16W
R9134 1-218-989-11 RES, CHIP 1M 5% 1/16WR9135 1-218-989-11 RES, CHIP 1M 5% 1/16WR9136 1-218-989-11 RES, CHIP 1M 5% 1/16WR9137 1-218-979-11 RES, CHIP 150K 5% 1/16WR9139 1-218-989-11 RES, CHIP 1M 5% 1/16W
R9140 1-208-715-11 METAL CHIP 22K 0.5% 1/16WR9143 1-218-990-11 SHORT 0R9144 1-208-711-11 METAL CHIP 15K 0.5% 1/16WR9147 1-218-989-11 RES, CHIP 1M 5% 1/16WR9148 1-218-990-11 SHORT 0
R9150 1-218-990-11 SHORT 0R9152 1-208-691-11 METAL CHIP 2.2K 0.5% 1/16WR9153 1-218-989-11 RES, CHIP 1M 5% 1/16WR9154 1-218-989-11 RES, CHIP 1M 5% 1/16WR9155 1-208-715-11 METAL CHIP 22K 0.5% 1/16W
R9156 1-208-927-11 METAL CHIP 47K 0.5% 1/16WR9157 1-218-959-11 RES, CHIP 3.3K 5% 1/16WR9159 1-208-927-11 METAL CHIP 47K 0.5% 1/16WR9161 1-218-989-11 RES, CHIP 1M 5% 1/16WR9901 1-218-990-11 SHORT 0
R9902 1-218-990-11 SHORT 0R9903 1-218-990-11 SHORT 0R9904 1-218-990-11 SHORT 0R9905 1-218-990-11 SHORT 0R9906 1-218-990-11 SHORT 0
R9910 1-218-990-11 SHORT 0
< SWITCH >
S8001 1-572-467-61 SWITCH, PUSH (1 KEY)(OPEN/CLOSE DETECT)
S8002 1-572-467-61 SWITCH, PUSH (1 KEY) (HALF LOCK DETECT)S8003 1-762-805-21 SWITCH, PUSH (1 KEY)
(OPEN CLOSE DETECT)
< BATTERY >
U8001 1-528-834-11 BATTERY, LITHIUM SECONDARY
< VIBRATOR >
X5301 1-767-498-11 OSCILLATOR, CRYSTAL (22.5792MHz)X5401 1-767-124-11 VIBRATOR, CRYSTAL (16.9344MHz)
X5403 1-781-247-21 VIBRATOR, CRYSTAL (70.54MHz)X8001 1-767-994-41 VIBRATOR, CRYSTAL (32.768kHz)X8002 1-767-994-22 VIBRATOR, CRYSTAL (32.768kHz)
X8003 1-781-259-21 VIBRATOR, CRYSTAL (9.8304MHz)X8501 1-781-260-21 VIBRATOR, CRYSTAL (6.6MHz)
************************************************************
A-3321-881-A POWER BOARD, COMPLETE***********************
(Ref. No.: 20,000 Series)
3-043-103-01 CUSHION (SHIELD)* 4-216-027-01 CASE (FRONT), SHIELD* 4-216-028-01 CASE (REAR), SHIELD
< CAPACITOR >
C9001 1-164-937-11 CERAMIC CHIP 0.001uF 10% 16VC9002 1-164-937-11 CERAMIC CHIP 0.001uF 10% 16VC9003 1-164-937-11 CERAMIC CHIP 0.001uF 10% 16VC9004 1-119-751-11 TANTALUM CHIP 22uF 20% 16VC9005 1-119-751-11 TANTALUM CHIP 22uF 20% 16V
C9007 1-119-923-81 CERAMIC CHIP 0.047uF 10% 10VC9008 1-107-820-11 CERAMIC CHIP 0.1uF 0% 16VC9009 1-107-820-11 CERAMIC CHIP 0.1uF 0% 16VC9010 1-107-820-11 CERAMIC CHIP 0.1uF 0% 16VC9011 1-119-751-11 TANTALUM CHIP 22uF 20% 16V
C9012 1-164-938-11 CERAMIC CHIP 0.0015uF 10% 16VC9013 1-164-874-11 CERAMIC CHIP 100PF 5% 16VC9014 1-164-489-11 CERAMIC CHIP 0.22uF 10% 16VC9015 1-119-751-11 TANTALUM CHIP 22uF 20% 16VC9017 1-164-942-11 CERAMIC CHIP 0.0068uF 10% 16V
C9018 1-119-751-11 TANTALUM CHIP 22uF 20% 16VC9019 1-164-941-11 CERAMIC CHIP 0.0047uF 10% 16VC9021 1-164-938-11 CERAMIC CHIP 0.0015uF 10% 16VC9023 1-164-939-11 CERAMIC CHIP 0.0022uF 10% 16VC9024 1-164-938-11 CERAMIC CHIP 0.0015uF 10% 16V
C9027 1-164-858-11 CERAMIC CHIP 22PF 5% 16VC9028 1-164-858-11 CERAMIC CHIP 22PF 5% 16VC9029 1-119-751-11 TANTALUM CHIP 22uF 20% 16VC9030 1-164-935-11 CERAMIC CHIP 470PF 10% 16VC9031 1-164-935-11 CERAMIC CHIP 470PF 10% 16V
C9032 1-164-858-11 CERAMIC CHIP 22PF 5% 16VC9033 1-164-935-11 CERAMIC CHIP 470PF 10% 16VC9034 1-164-858-11 CERAMIC CHIP 22PF 5% 16VC9035 1-164-935-11 CERAMIC CHIP 470PF 10% 16VC9036 1-164-935-11 CERAMIC CHIP 470PF 10% 16V
C9037 1-164-935-11 CERAMIC CHIP 470PF 10% 16VC9038 1-164-858-11 CERAMIC CHIP 22PF 5% 16VC9039 1-164-858-11 CERAMIC CHIP 22PF 5% 16VC9040 1-119-751-11 TANTALUM CHIP 22uF 20% 16VC9041 1-119-751-11 TANTALUM CHIP 22uF 20% 16V
C9042 1-115-566-11 CERAMIC CHIP 4.7uF 10% 10VC9043 1-115-566-11 CERAMIC CHIP 4.7uF 10% 10VC9044 1-115-566-11 CERAMIC CHIP 4.7uF 10% 10VC9045 1-115-566-11 CERAMIC CHIP 4.7uF 10% 10VC9046 1-115-566-11 CERAMIC CHIP 4.7uF 10% 10V
C9047 1-115-566-11 CERAMIC CHIP 4.7uF 10% 10VC9048 1-104-851-11 TANTALUM CHIP 10uF 20% 10VC9049 1-104-851-11 TANTALUM CHIP 10uF 20% 10V
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
6-16
C9050 1-104-851-11 TANTALUM CHIP 10uF 20% 10VC9051 1-104-852-11 TANTALUM CHIP 22uF 20% 10V
C9052 1-164-937-11 CERAMIC CHIP 0.001uF 10% 16VC9053 1-115-339-11 CERAMIC CHIP 0.1uF 10% 50VC9055 1-104-913-11 TANTALUM CHIP 10uF 20% 16VC9057 1-110-569-11 TANTALUM CHIP 47uF 20% 6.3VC9059 1-115-339-11 CERAMIC CHIP 0.1uF 10% 50V
C9061 1-104-852-11 TANTALUM CHIP 22uF 20% 10VC9062 1-115-566-11 CERAMIC CHIP 4.7uF 10% 10VC9063 1-104-852-11 TANTALUM CHIP 22uF 20% 10VC9064 1-104-916-11 TANTALUM CHIP 6.8uF 20% 20VC9065 1-104-852-11 TANTALUM CHIP 22uF 20% 10V
C9066 1-107-820-11 CERAMIC CHIP 0.1uF 0% 16VC9067 1-107-820-11 CERAMIC CHIP 0.1uF 0% 16VC9068 1-104-916-11 TANTALUM CHIP 6.8uF 20% 20VC9069 1-107-820-11 CERAMIC CHIP 0.1uF 0% 16VC9070 1-113-994-11 TANTALUM CHIP 6.8uF 20% 16V
C9071 1-113-994-11 TANTALUM CHIP 6.8uF 20% 16VC9072 1-113-984-11 TANTALUM CHIP 1.5uF 20% 35VC9073 1-104-752-11 TANTALUM CHIP 33uF 20% 6.3VC9074 1-104-916-11 TANTALUM CHIP 6.8uF 20% 20VC9076 1-113-682-11 TANTALUM CHIP 33uF 20% 10V
C9077 1-115-566-11 CERAMIC CHIP 4.7uF 10% 10VC9078 1-115-566-11 CERAMIC CHIP 4.7uF 10% 10VC9079 1-115-566-11 CERAMIC CHIP 4.7uF 10% 10VC9080 1-115-566-11 CERAMIC CHIP 4.7uF 10% 10VC9081 1-115-566-11 CERAMIC CHIP 4.7uF 10% 10V
< CONNECTOR >
CN9001 1-785-482-41 CONNECTOR, BOARD TO BOARD 70P* CN9002 1-695-106-11 PIN, CONNECTOR (PC BOARD) 4P
< DIODE >
D9001 8-719-074-63 DIODE MAZS120001SOD9002 8-719-074-63 DIODE MAZS120001SOD9003 8-719-074-63 DIODE MAZS120001SOD9004 8-719-074-63 DIODE MAZS120001SOD9005 8-719-074-63 DIODE MAZS120001SO
D9006 8-719-067-36 DIODE MA3ZD1200LS0D9007 8-719-067-36 DIODE MA3ZD1200LS0D9008 8-719-067-36 DIODE MA3ZD1200LS0D9009 8-719-067-36 DIODE MA3ZD1200LS0D9010 8-719-067-36 DIODE MA3ZD1200LS0
D9011 8-719-074-63 DIODE MAZS120001SOD9012 8-719-056-48 DIODE 1SS388 (TPL3)D9013 8-719-056-48 DIODE 1SS388 (TPL3)D9014 8-719-056-48 DIODE 1SS388 (TPL3)D9015 8-719-056-48 DIODE 1SS388 (TPL3)
< FUSE >
0F9001 1-533-760-21 FUSE (SMD) (1.4A/24V)0F9002 1-533-760-21 FUSE (SMD) (1.4A/24V)0F9003 1-533-760-21 FUSE (SMD) (1.4A/24V)0F9004 1-533-760-21 FUSE (SMD) (1.4A/24V)
< FERRITE BEAD >
* FB9001 1-469-230-21 FERRITE 0uH* FB9002 1-469-230-21 FERRITE 0uH
< IC >
IC9001 8-759-596-54 IC SN104241PM-TEBIC9002 8-759-252-41 IC TK11900MTL
< COIL >
L9001 1-409-529-41 INDUCTOR 10uHL9002 1-409-529-41 INDUCTOR 10uHL9003 1-409-529-41 INDUCTOR 10uHL9004 1-414-757-11 INDUCTOR 100uHL9005 1-409-529-41 INDUCTOR 10uH
L9006 1-424-674-11 INDUCTOR 22uHL9007 1-409-535-41 INDUCTOR 100uHL9008 1-409-535-41 INDUCTOR 100uHL9009 1-409-529-41 INDUCTOR 10uHL9010 1-409-529-41 INDUCTOR 10uH
L9013 1-469-367-21 INDUCTOR 10uHL9015 1-414-757-11 INDUCTOR 100uHL9016 1-414-757-11 INDUCTOR 100uHL9017 1-469-367-21 INDUCTOR 10uHL9018 1-469-367-21 INDUCTOR 10uH
L9019 1-469-367-21 INDUCTOR 10uHL9020 1-414-757-11 INDUCTOR 100uHL9021 1-414-757-11 INDUCTOR 100uHL9022 1-414-757-11 INDUCTOR 100uHL9023 1-469-367-21 INDUCTOR 10uH
< TRANSISTOR >
Q9001 8-729-804-41 TRANSISTOR 2SB1122-SQ9002 8-729-037-52 TRANSISTOR 2SD2216J-QR (TX).SOQ9003 8-729-043-94 TRANSISTOR CPH3106-PM-TLQ9004 8-729-043-94 TRANSISTOR CPH3106-PM-TLQ9005 8-729-043-94 TRANSISTOR CPH3106-PM-TL
Q9006 8-729-043-94 TRANSISTOR CPH3106-PM-TLQ9007 8-729-047-38 TRANSISTOR FDN359ANQ9008 8-729-047-38 TRANSISTOR FDN359ANQ9009 8-729-043-94 TRANSISTOR CPH3106-PM-TLQ9010 8-729-427-70 TRANSISTOR XP4401
< RESISTOR >
R9001 1-208-699-11 METAL CHIP 4.7K 0.5% 1/16WR9003 1-208-707-11 METAL CHIP 10K 0.5% 1/16WR9004 1-218-973-11 RES, CHIP 47K 5% 1/16WR9005 1-218-969-11 RES, CHIP 22K 5% 1/16WR9006 1-218-973-11 RES, CHIP 47K 5% 1/16W
R9007 1-208-699-11 METAL CHIP 4.7K 0.5% 1/16WR9008 1-218-967-11 RES, CHIP 15K 5% 1/16WR9011 1-218-965-11 RES, CHIP 10K 5% 1/16WR9013 1-218-965-11 RES, CHIP 10K 5% 1/16WR9014 1-218-959-11 RES, CHIP 3.3K 5% 1/16W
R9015 1-218-965-11 RES, CHIP 10K 5% 1/16WR9016 1-208-715-11 METAL CHIP 22K 0.5% 1/16WR9017 1-208-715-11 METAL CHIP 22K 0.5% 1/16WR9019 1-208-927-11 METAL CHIP 47K 0.5% 1/16WR9020 1-218-969-11 RES, CHIP 22K 5% 1/16W
R9021 1-208-715-11 METAL CHIP 22K 0.5% 1/16WR9022 1-208-703-11 METAL CHIP 6.8K 0.5% 1/16WR9023 1-208-715-11 METAL CHIP 22K 0.5% 1/16WR9024 1-208-715-11 METAL CHIP 22K 0.5% 1/16W
POWER
The components identified bymark 0 or dotted line withmark 0 are critical for safety.Replace only with part num-ber specified.
Les composants identifiés par unemarque 0 sont critiques pour lasécurité.Ne les remplacer que par une pièceportant le numéro spécifié.
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
6-17
R9025 1-208-691-11 METAL CHIP 2.2K 0.5% 1/16W
R9029 1-208-703-11 METAL CHIP 6.8K 0.5% 1/16WR9031 1-218-965-11 RES, CHIP 10K 5% 1/16WR9032 1-218-965-11 RES, CHIP 10K 5% 1/16WR9033 1-208-707-11 METAL CHIP 10K 0.5% 1/16WR9035 1-208-703-11 METAL CHIP 6.8K 0.5% 1/16W
R9036 1-208-703-11 METAL CHIP 6.8K 0.5% 1/16WR9037 1-218-849-11 METAL CHIP 3.3K 0.5% 1/16WR9038 1-218-959-11 RES, CHIP 3.3K 5% 1/16WR9039 1-218-849-11 METAL CHIP 3.3K 0.5% 1/16WR9040 1-218-849-11 METAL CHIP 3.3K 0.5% 1/16W
R9041 1-208-683-11 METAL CHIP 1K 0.5% 1/16WR9042 1-218-975-11 RES, CHIP 68K 5% 1/16WR9043 1-218-971-11 RES, CHIP 33K 5% 1/16WR9044 1-218-971-11 RES, CHIP 33K 5% 1/16WR9045 1-218-965-11 RES, CHIP 10K 5% 1/16W
R9046 1-218-955-11 RES, CHIP 1.5K 5% 1/16WR9047 1-208-935-11 METAL CHIP 100K 0.5% 1/16WR9048 1-208-927-11 METAL CHIP 47K 0.5% 1/16WR9049 1-208-711-11 METAL CHIP 15K 0.5% 1/16WR9050 1-208-699-11 METAL CHIP 4.7K 0.5% 1/16W
R9051 1-218-969-11 RES, CHIP 22K 5% 1/16WR9052 1-208-943-11 METAL CHIP 220K 0.5% 1/16WR9053 1-208-935-11 METAL CHIP 100K 0.5% 1/16WR9054 1-208-715-11 METAL CHIP 22K 0.5% 1/16WR9055 1-208-931-11 METAL CHIP 68K 0.5% 1/16W
R9056 1-218-977-11 RES, CHIP 100K 5% 1/16WR9058 1-208-935-11 METAL CHIP 100K 0.5% 1/16WR9059 1-208-715-11 METAL CHIP 22K 0.5% 1/16WR9060 1-218-933-11 RES, CHIP 22 5% 1/16WR9062 1-218-933-11 RES, CHIP 22 5% 1/16W
R9064 1-218-933-11 RES, CHIP 22 5% 1/16WR9066 1-219-365-11 SHORT 0R9067 1-216-296-91 SHORT 0R9068 1-211-950-11 SHORT 0
< TRANSFORMER >
0T9001 1-433-623-21 TRANSFORMER, CONVERTER************************************************************
A-3321-863-A REC BOARD, COMPLETE*********************
(Ref. No.: 20,000 Series)
< CAPACITOR >
C5901 1-107-820-11 CERAMIC CHIP 0.1uF 0% 16VC5902 1-117-177-91 CAP-CHIP 33PF 5% 500VC5903 1-104-851-11 TANTALUM CHIP 10uF 20% 10VC5904 1-104-851-11 TANTALUM CHIP 10uF 20% 10VC5905 1-104-851-11 TANTALUM CHIP 10uF 20% 10V
C5906 1-107-820-11 CERAMIC CHIP 0.1uF 0% 16V
< CONNECTOR >
CN5901 1-778-711-11 CONNECTOR, FFC/FPC (ZIF) 5P* CN5902 1-778-158-21 CONNECTOR, FFC/FPC (ZIF) 10P
< DIODE >
D5901 8-719-073-16 DIODE SBE802-TLD5902 8-719-073-16 DIODE SBE802-TL
< IC >
IC5901 8-759-475-53 IC TC74LCX541FT (EL)
< TRANSISTOR >
Q5901 8-729-037-73 TRANSISTOR UN9212J- (TX).SOQ5902 8-729-047-35 TRANSISTOR FTD1003-TLQ5903 8-729-047-82 TRANSISTOR FTD2007-TL
< RESISTOR >
R5901 1-218-983-11 RES, CHIP 330K 5% 1/16WR5902 1-218-983-11 RES, CHIP 330K 5% 1/16WR5903 1-218-983-11 RES, CHIP 330K 5% 1/16WR5904 1-218-983-11 RES, CHIP 330K 5% 1/16WR5905 1-218-983-11 RES, CHIP 330K 5% 1/16W
************************************************************
VC-216 BOARD, COMPLETE***********************
(Ref. No.: 20,000 Series)
< CAPACITOR >
C001 1-104-851-11 TANTALUM CHIP 10uF 20% 10VC002 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16VC003 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16VC004 1-164-850-11 CERAMIC CHIP 10PF 0.5PF 16VC007 1-107-826-91 CERAMIC CHIP 0.1uF 10% 16V
C008 1-119-750-11 TANTALUM CHIP 22uF 20% 6.3VC009 1-113-994-11 TANTALUM CHIP 6.8uF 20% 16VC010 1-107-826-91 CERAMIC CHIP 0.1uF 10% 16VC011 1-119-750-11 TANTALUM CHIP 22uF 20% 6.3VC012 1-107-826-91 CERAMIC CHIP 0.1uF 10% 16V
C013 1-165-176-11 CERAMIC CHIP 0.047uF 10% 16VC014 1-165-176-11 CERAMIC CHIP 0.047uF 10% 16VC015 1-107-826-91 CERAMIC CHIP 0.1uF 10% 16VC016 1-165-176-11 CERAMIC CHIP 0.047uF 10% 16VC017 1-165-176-11 CERAMIC CHIP 0.047uF 10% 16V
C018 1-125-817-11 CERAMIC CHIP 10uF 10% 6.3VC019 1-125-817-11 CERAMIC CHIP 10uF 10% 6.3VC020 1-125-817-11 CERAMIC CHIP 10uF 10% 6.3VC021 1-125-817-11 CERAMIC CHIP 10uF 10% 6.3VC022 1-110-501-11 CERAMIC CHIP 0.33uF 10% 16V
C023 1-107-826-91 CERAMIC CHIP 0.1uF 10% 16VC024 1-119-750-11 TANTALUM CHIP 22uF 20% 6.3VC101 1-164-506-11 CERAMIC CHIP 4.7uF 0% 16VC102 1-164-506-11 CERAMIC CHIP 4.7uF 0% 16VC103 1-164-862-11 CERAMIC CHIP 33PF 5% 16V
C104 1-109-982-11 CERAMIC CHIP 1uF 10% 10VC105 1-164-862-11 CERAMIC CHIP 33PF 5% 16VC106 1-107-826-91 CERAMIC CHIP 0.1uF 10% 16VC107 1-119-750-11 TANTALUM CHIP 22uF 20% 6.3VC108 1-125-839-91 TANTALUM CHIP 47uF 20% 6.3V
C109 1-107-826-91 CERAMIC CHIP 0.1uF 10% 16VC110 1-107-826-91 CERAMIC CHIP 0.1uF 10% 16VC111 1-107-826-91 CERAMIC CHIP 0.1uF 10% 16V
POWER REC VC-216
The components identified bymark 0 or dotted line withmark 0 are critical for safety.Replace only with part num-ber specified.
Les composants identifiés par unemarque 0 sont critiques pour lasécurité.Ne les remplacer que par une pièceportant le numéro spécifié.
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
6-18
C112 1-107-826-91 CERAMIC CHIP 0.1uF 10% 16VC113 1-107-826-91 CERAMIC CHIP 0.1uF 10% 16V
C114 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16VC115 1-165-176-11 CERAMIC CHIP 0.047uF 10% 16VC116 1-165-176-11 CERAMIC CHIP 0.047uF 10% 16VC117 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16VC118 1-107-826-91 CERAMIC CHIP 0.1uF 10% 16V
C119 1-164-846-11 CERAMIC CHIP 6PF 0.5PF 16VC120 1-107-826-91 CERAMIC CHIP 0.1uF 10% 16VC121 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16VC123 1-107-826-91 CERAMIC CHIP 0.1uF 10% 16VC124 1-107-826-91 CERAMIC CHIP 0.1uF 10% 16V
C125 1-125-837-91 CERAMIC CHIP 1uF 10% 6.3VC126 1-107-826-91 CERAMIC CHIP 0.1uF 10% 16VC127 1-107-826-91 CERAMIC CHIP 0.1uF 10% 16VC128 1-117-919-11 TANTALUM CHIP 10uF 20% 6.3VC129 1-119-750-11 TANTALUM CHIP 22uF 20% 6.3V
C130 1-107-826-91 CERAMIC CHIP 0.1uF 10% 16VC131 1-107-826-91 CERAMIC CHIP 0.1uF 10% 16VC132 1-125-837-91 CERAMIC CHIP 1uF 10% 6.3VC133 1-165-176-11 CERAMIC CHIP 0.047uF 10% 16VC134 1-117-920-11 TANTALUM CHIP 10uF 20% 6.3V
C135 1-107-826-91 CERAMIC CHIP 0.1uF 10% 16VC136 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16VC137 1-117-920-11 TANTALUM CHIP 10uF 20% 6.3VC138 1-107-826-91 CERAMIC CHIP 0.1uF 10% 16VC139 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16V
C140 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16VC141 1-107-826-91 CERAMIC CHIP 0.1uF 10% 16VC142 1-109-982-11 CERAMIC CHIP 1uF 10% 10VC143 1-164-850-11 CERAMIC CHIP 10PF 0.5PF 16VC201 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16V
C202 1-164-941-11 CERAMIC CHIP 0.0047uF 10% 16VC203 1-107-826-91 CERAMIC CHIP 0.1uF 10% 16VC204 1-107-826-91 CERAMIC CHIP 0.1uF 10% 16VC205 1-164-935-11 CERAMIC CHIP 470PF 10% 16VC206 1-164-489-11 CERAMIC CHIP 0.22uF 10% 16V
C207 1-164-937-11 CERAMIC CHIP 0.001uF 10% 16VC208 1-107-823-11 CERAMIC CHIP 0.47uF 10% 16VC209 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16VC210 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16VC211 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16V
C212 1-164-939-11 CERAMIC CHIP 0.0022uF 10% 16VC213 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16VC214 1-107-826-91 CERAMIC CHIP 0.1uF 10% 16VC215 1-117-920-11 TANTALUM CHIP 10uF 20% 6.3VC216 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16V
C217 1-107-826-91 CERAMIC CHIP 0.1uF 10% 16VC218 1-107-826-91 CERAMIC CHIP 0.1uF 10% 16VC219 1-119-750-11 TANTALUM CHIP 22uF 20% 6.3VC220 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16VC221 1-125-839-91 TANTALUM CHIP 47uF 20% 6.3V
C222 1-119-750-11 TANTALUM CHIP 22uF 20% 6.3V
< CONNECTOR >
CN101 1-778-804-11 CONNECTOR, BOARD TO BOARD 40PCN201 1-766-354-21 CONNECTOR, FFC/FPC 24P
< DIODE >
D101 8-713-103-84 DIODE 1T379-01-T8AD201 8-719-056-23 DIODE MA2S111- (K8).SO
< FERRITE BEAD >
FB101 1-414-228-11 FERRITE 0uHFB102 1-500-284-21 FERRITE 0uHFB103 1-414-228-11 FERRITE 0uHFB104 1-414-228-11 FERRITE 0uHFB105 1-414-228-11 FERRITE 0uH
FB201 1-414-228-11 FERRITE 0uH
< IC >
IC002 8-759-489-19 IC uPC6756GR-8JG-E2IC101 8-752-386-72 IC CXD2444RIC102 8-759-570-81 IC AD9808AJSTRLIC103 8-759-445-93 IC AK6440AM-E2IC104 8-759-387-31 IC TC75S55F (TE85R)
IC105 8-759-497-43 IC CXD8691R-TEBIC106 8-752-904-85 IC CXP912032-098R-T6IC201 8-759-444-87 IC NJM324V (TE2)IC202 8-759-492-31 IC MPC17A134VMEL
< COIL >
L001 1-414-757-11 INDUCTOR 100uHL002 1-414-754-11 INDUCTOR 10uHL101 1-414-754-11 INDUCTOR 10uHL103 1-414-754-11 INDUCTOR 10uHL104 1-414-754-11 INDUCTOR 10uH
L201 1-414-754-11 INDUCTOR 10uHL202 1-414-754-11 INDUCTOR 10uHL203 1-414-754-11 INDUCTOR 10uH
< TRANSISTOR >
Q001 8-729-117-73 TRANSISTOR 2SC4178-F14Q101 8-729-037-61 TRANSISTOR UN9113J- (TX).SOQ102 8-729-037-74 TRANSISTOR UN9213J- (TX).SOQ103 8-729-037-61 TRANSISTOR UN9113J- (TX).SOQ104 8-729-037-74 TRANSISTOR UN9213J- (TX).SO
Q201 8-729-037-53 TRANSISTOR 2SB1462J-QR (TX).SOQ202 8-729-037-52 TRANSISTOR 2SD2216J-QR (TX).SOQ203 8-729-037-53 TRANSISTOR 2SB1462J-QR (TX).SOQ204 8-729-037-52 TRANSISTOR 2SD2216J-QR (TX).SO
< RESISTOR/FILTER>
R005 1-218-959-11 RES, CHIP 3.3K 5% 1/16WR007 1-218-969-11 RES, CHIP 22K 5% 1/16WR008 1-218-933-11 RES, CHIP 22 5% 1/16WR009 1-218-969-11 RES, CHIP 22K 5% 1/16WR010 1-218-969-11 RES, CHIP 22K 5% 1/16W
R011 1-218-969-11 RES, CHIP 22K 5% 1/16WR012 1-218-965-11 RES, CHIP 10K 5% 1/16WR013 1-218-965-11 RES, CHIP 10K 5% 1/16WR014 1-218-989-11 RES, CHIP 1M 5% 1/16WR015 1-218-967-11 RES, CHIP 15K 5% 1/16W
R016 1-218-989-11 RES, CHIP 1M 5% 1/16WR101 1-469-537-21 FILTER 0uH
VC-216
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
6-19
VC-216 VF
R102 1-469-537-21 FILTER 0uHR103 1-218-933-11 RES, CHIP 22 5% 1/16WR104 1-218-977-11 RES, CHIP 100K 5% 1/16W
R105 1-218-945-11 RES, CHIP 220 5% 1/16WR106 1-218-977-11 RES, CHIP 100K 5% 1/16WR107 1-218-990-11 SHORT 0R108 1-218-985-11 RES, CHIP 470K 5% 1/16WR109 1-218-983-11 RES, CHIP 330K 5% 1/16W
R110 1-218-953-11 RES, CHIP 1K 5% 1/16WR111 1-218-973-11 RES, CHIP 47K 5% 1/16WR112 1-218-973-11 RES, CHIP 47K 5% 1/16WR113 1-218-953-11 RES, CHIP 1K 5% 1/16WR115 1-218-977-11 RES, CHIP 100K 5% 1/16W
R116 1-218-977-11 RES, CHIP 100K 5% 1/16WR117 1-216-864-11 METAL CHIP 0 5% 1/16WR118 1-218-941-11 RES, CHIP 100 5% 1/16WR119 1-218-941-11 RES, CHIP 100 5% 1/16WR120 1-218-977-11 RES, CHIP 100K 5% 1/16W
R121 1-218-977-11 RES, CHIP 100K 5% 1/16WR122 1-218-977-11 RES, CHIP 100K 5% 1/16WR123 1-218-933-11 RES, CHIP 22 5% 1/16WR124 1-218-953-11 RES, CHIP 1K 5% 1/16WR125 1-218-973-11 RES, CHIP 47K 5% 1/16W
R126 1-218-989-11 RES, CHIP 1M 5% 1/16WR127 1-218-973-11 RES, CHIP 47K 5% 1/16WR128 1-218-953-11 RES, CHIP 1K 5% 1/16WR129 1-218-989-11 RES, CHIP 1M 5% 1/16WR130 1-218-989-11 RES, CHIP 1M 5% 1/16W
R131 1-218-977-11 RES, CHIP 100K 5% 1/16WR132 1-218-961-11 RES, CHIP 4.7K 5% 1/16WR133 1-218-961-11 RES, CHIP 4.7K 5% 1/16WR134 1-218-957-11 RES, CHIP 2.2K 5% 1/16WR135 1-218-965-11 RES, CHIP 10K 5% 1/16W
R136 1-216-864-11 METAL CHIP 0 5% 1/16WR137 1-216-864-11 METAL CHIP 0 5% 1/16WR138 1-216-009-91 RES, CHIP 22 5% 1/10WR201 1-218-961-11 RES, CHIP 4.7K 5% 1/16WR202 1-218-975-11 RES, CHIP 68K 5% 1/16W
R203 1-216-864-11 METAL CHIP 0 5% 1/16WR205 1-218-975-11 RES, CHIP 68K 5% 1/16WR206 1-218-989-11 RES, CHIP 1M 5% 1/16WR207 1-218-961-11 RES, CHIP 4.7K 5% 1/16WR208 1-218-957-11 RES, CHIP 2.2K 5% 1/16W
R209 1-218-953-11 RES, CHIP 1K 5% 1/16WR210 1-218-981-11 RES, CHIP 220K 5% 1/16WR211 1-218-965-11 RES, CHIP 10K 5% 1/16WR212 1-218-985-11 RES, CHIP 470K 5% 1/16WR213 1-218-985-11 RES, CHIP 470K 5% 1/16W
R214 1-218-957-11 RES, CHIP 2.2K 5% 1/16WR215 1-218-969-11 RES, CHIP 22K 5% 1/16WR216 1-218-963-11 RES, CHIP 6.8K 5% 1/16WR217 1-218-985-11 RES, CHIP 470K 5% 1/16WR218 1-218-953-11 RES, CHIP 1K 5% 1/16W
R219 1-218-953-11 RES, CHIP 1K 5% 1/16WR220 1-218-947-11 RES, CHIP 330 5% 1/16WR221 1-218-969-11 RES, CHIP 22K 5% 1/16WR222 1-218-953-11 RES, CHIP 1K 5% 1/16WR223 1-218-965-11 RES, CHIP 10K 5% 1/16W
R224 1-218-973-11 RES, CHIP 47K 5% 1/16WR225 1-216-864-11 METAL CHIP 0 5% 1/16WR226 1-216-864-11 METAL CHIP 0 5% 1/16W
< SENSOR >
SE001 1-803-042-41 SENSOR, ANGULAR VELOCITY (YAW SENSOR)SE201 1-803-042-31 SENSOR, ANGULAR VELOCITY
(PITCH SENSOR)
< VIBRATOR >
X101 1-767-203-21 VIBRATOR, CRYSTAL (36MHz)X102 1-767-980-21 VIBRATOR, CERAMIC (20MHz)
************************************************************
A-3321-879-A VF BOARD, COMPLETE*******************
(Ref. No.: 20,000 Series)
< CAPACITOR >
C4501 1-125-777-11 CERAMIC CHIP 0.1uF 10% 6.3VC4502 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16VC4503 1-104-851-11 TANTALUM CHIP 10uF 20% 10VC4504 1-104-851-11 TANTALUM CHIP 10uF 20% 10VC4505 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16V
C4506 1-119-750-11 TANTALUM CHIP 22uF 20% 6.3VC4507 1-117-919-11 TANTALUM CHIP 10uF 20% 6.3VC4508 1-135-179-21 TANTALUM CHIP 2.2uF 20% 16VC4509 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10VC4510 1-107-686-11 TANTALUM CHIP 4.7uF 20% 16V
C4512 1-119-750-11 TANTALUM CHIP 22uF 20% 6.3VC4514 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10VC4515 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10VC4516 1-107-686-11 TANTALUM CHIP 4.7uF 20% 16VC4517 1-107-686-11 TANTALUM CHIP 4.7uF 20% 16V
C4518 1-107-686-11 TANTALUM CHIP 4.7uF 20% 16VC4519 1-115-566-11 CERAMIC CHIP 4.7uF 10% 10VC4520 1-119-750-11 TANTALUM CHIP 22uF 20% 6.3VC4521 1-135-179-21 TANTALUM CHIP 2.2uF 20% 16VC4522 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16V
C4523 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10VC4524 1-164-505-11 CERAMIC CHIP 2.2uF 0% 16VC4525 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10VC4526 1-107-686-11 TANTALUM CHIP 4.7uF 20% 16VC4527 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16V
C4601 1-115-467-11 CERAMIC CHIP 0.22uF 10% 10VC4602 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16VC4603 1-104-851-11 TANTALUM CHIP 10uF 20% 10VC4604 1-107-826-91 CERAMIC CHIP 0.1uF 10% 16VC4605 1-104-916-11 TANTALUM CHIP 6.8uF 20% 20V
C4606 1-164-939-11 CERAMIC CHIP 0.0022uF 10% 16VC4608 1-107-686-11 TANTALUM CHIP 4.7uF 20% 16VC4610 1-107-819-11 CERAMIC CHIP 0.022uF 10% 16VC4611 1-107-819-11 CERAMIC CHIP 0.022uF 10% 16VC4612 1-109-982-11 CERAMIC CHIP 1uF 10% 10V
C4613 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16VC4614 1-164-878-11 CERAMIC CHIP 150PF 5% 16VC4615 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16VC4616 1-164-940-11 CERAMIC CHIP 0.0033uF 10% 16VC4617 1-115-566-11 CERAMIC CHIP 4.7uF 10% 10V
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
6-20
C4618 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16VC4619 1-135-259-11 TANTALUM CHIP 10uF 20% 6.3VC4620 1-164-874-11 CERAMIC CHIP 100PF 5% 16VC4621 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50VC4622 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16V
C4624 1-107-820-11 CERAMIC CHIP 0.1uF 0% 16VC4625 1-165-112-11 CERAMIC CHIP 0.33uF 0% 16V
< CONNECTOR >
CN4501 1-784-420-11 CONNECTOR, FFC/FPC (ZIF) 21PCN4601 1-778-596-21 CONNECTOR, BOARD TO BOARD 30PCN4901 1-764-704-21 CONNECTOR, FFC/FPC (LIF) 5P
< DIODE >
D4601 8-719-043-70 DIODE MA6S121- (TX)D4602 8-713-102-80 DIODE 1T369-01-T8A
< IC >
IC4501 8-759-546-65 IC CXA8115AR-T4IC4502 8-759-596-12 IC AK9813AFS-E2IC4601 8-759-097-75 IC MB3789PFV-G-BNDIC4602 8-752-392-33 IC CXD2458AR
< COIL >
L4501 1-414-754-11 INDUCTOR 10uHL4502 1-414-754-11 INDUCTOR 10uHL4503 1-414-754-11 INDUCTOR 10uHL4601 1-414-406-41 INDUCTOR 220uHL4602 1-414-756-11 INDUCTOR 47uH
L4603 1-412-949-21 INDUCTOR 6.8uH
< TRANSISTOR >
Q4502 8-729-037-53 TRANSISTOR 2SB1462J-QR (TX).SOQ4503 8-729-037-53 TRANSISTOR 2SB1462J-QR (TX).SOQ4504 8-729-037-53 TRANSISTOR 2SB1462J-QR (TX).SOQ4505 8-729-037-53 TRANSISTOR 2SB1462J-QR (TX).SOQ4506 8-729-037-53 TRANSISTOR 2SB1462J-QR (TX).SO
Q4507 8-729-037-53 TRANSISTOR 2SB1462J-QR (TX).SOQ4601 8-729-013-73 TRANSISTOR RN2105-TE85RQ4602 8-729-037-61 TRANSISTOR UN9113J- (TX).SOQ4603 8-729-037-74 TRANSISTOR UN9213J- (TX).SO
< RESISTOR >
R4501 1-216-009-91 RES, CHIP 22 5% 1/10WR4502 1-218-969-11 RES, CHIP 22K 5% 1/16WR4503 1-218-990-11 SHORT 0R4507 1-218-969-11 RES, CHIP 22K 5% 1/16WR4508 1-218-975-11 RES, CHIP 68K 5% 1/16W
R4514 1-208-711-11 METAL CHIP 15K 0.5% 1/16WR4515 1-208-691-11 METAL CHIP 2.2K 0.5% 1/16WR4516 1-218-990-11 SHORT 0R4517 1-218-990-11 SHORT 0R4518 1-218-990-11 SHORT 0
R4519 1-208-675-11 METAL CHIP 470 0.5% 1/16WR4520 1-208-683-11 METAL CHIP 1K 0.5% 1/16WR4523 1-218-971-11 RES, CHIP 33K 5% 1/16WR4524 1-218-975-11 RES, CHIP 68K 5% 1/16W
R4525 1-218-975-11 RES, CHIP 68K 5% 1/16W
R4526 1-218-971-11 RES, CHIP 33K 5% 1/16WR4527 1-218-985-11 RES, CHIP 470K 5% 1/16WR4528 1-218-971-11 RES, CHIP 33K 5% 1/16WR4529 1-218-957-11 RES, CHIP 2.2K 5% 1/16WR4530 1-218-971-11 RES, CHIP 33K 5% 1/16W
R4531 1-218-975-11 RES, CHIP 68K 5% 1/16WR4532 1-218-971-11 RES, CHIP 33K 5% 1/16WR4533 1-218-849-11 METAL CHIP 3.3K 0.5% 1/16WR4534 1-208-675-11 METAL CHIP 470 0.5% 1/16WR4535 1-208-683-11 METAL CHIP 1K 0.5% 1/16W
R4538 1-218-971-11 RES, CHIP 33K 5% 1/16WR4539 1-218-975-11 RES, CHIP 68K 5% 1/16WR4540 1-218-990-11 SHORT 0R4541 1-218-941-11 RES, CHIP 100 5% 1/16WR4542 1-218-941-11 RES, CHIP 100 5% 1/16W
R4543 1-218-941-11 RES, CHIP 100 5% 1/16WR4544 1-218-957-11 RES, CHIP 2.2K 5% 1/16WR4546 1-218-903-11 METAL CHIP 220K 0.5% 1/16WR4547 1-218-887-11 METAL CHIP 47K 0.5% 1/16WR4550 1-218-990-11 SHORT 0
R4551 1-218-990-11 SHORT 0R4553 1-208-691-11 METAL CHIP 2.2K 0.5% 1/16WR4556 1-218-969-11 RES, CHIP 22K 5% 1/16WR4557 1-208-675-11 METAL CHIP 470 0.5% 1/16WR4558 1-208-683-11 METAL CHIP 1K 0.5% 1/16W
R4559 1-218-971-11 RES, CHIP 33K 5% 1/16WR4560 1-218-975-11 RES, CHIP 68K 5% 1/16WR4561 1-218-957-11 RES, CHIP 2.2K 5% 1/16WR4562 1-218-875-11 METAL CHIP 15K 0.5% 1/16WR4564 1-218-990-11 SHORT 0
R4565 1-218-990-11 SHORT 0R4566 1-218-990-11 SHORT 0R4567 1-218-990-11 SHORT 0R4568 1-218-990-11 SHORT 0R4570 1-208-707-11 METAL CHIP 10K 0.5% 1/16W
R4601 1-217-671-11 METAL CHIP 1 5% 1/10WR4602 1-217-671-11 METAL CHIP 1 5% 1/10WR4603 1-208-719-11 METAL CHIP 33K 0.5% 1/16WR4604 1-218-971-11 RES, CHIP 33K 5% 1/16WR4605 1-208-939-11 METAL CHIP 150K 0.5% 1/16W
R4607 1-208-927-11 METAL CHIP 47K 0.5% 1/16WR4608 1-218-975-11 RES, CHIP 68K 5% 1/16WR4609 1-218-981-11 RES, CHIP 220K 5% 1/16WR4610 1-218-973-11 RES, CHIP 47K 5% 1/16WR4611 1-218-965-11 RES, CHIP 10K 5% 1/16W
R4612 1-218-973-11 RES, CHIP 47K 5% 1/16WR4613 1-218-973-11 RES, CHIP 47K 5% 1/16WR4614 1-218-965-11 RES, CHIP 10K 5% 1/16WR4615 1-218-969-11 RES, CHIP 22K 5% 1/16WR4616 1-218-969-11 RES, CHIP 22K 5% 1/16W
R4617 1-218-985-11 RES, CHIP 470K 5% 1/16WR4618 1-218-953-11 RES, CHIP 1K 5% 1/16WR4619 1-218-971-11 RES, CHIP 33K 5% 1/16WR4620 1-218-979-11 RES, CHIP 150K 5% 1/16WR4621 1-218-979-11 RES, CHIP 150K 5% 1/16W
R4622 1-218-961-11 RES, CHIP 4.7K 5% 1/16W
VF
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
6-21
R4623 1-218-983-11 RES, CHIP 330K 5% 1/16WR4624 1-218-971-11 RES, CHIP 33K 5% 1/16WR4626 1-218-969-11 RES, CHIP 22K 5% 1/16WR4627 1-218-965-11 RES, CHIP 10K 5% 1/16W
R4628 1-218-971-11 RES, CHIP 33K 5% 1/16WR4629 1-218-990-11 SHORT 0R4630 1-218-953-11 RES, CHIP 1K 5% 1/16WR4634 1-218-990-11 SHORT 0R4636 1-218-963-11 RES, CHIP 6.8K 5% 1/16W
************************************************************
MISCELLANEOUS***************
14 1-418-201-21 SWITCH UNIT, MAIN CONTROL56 1-672-513-11 TRANSLATION FLEXIBLE (JACK) BOARD61 1-418-563-11 TERMINAL UNIT, REMOTE69 1-418-202-21 SWITCH UNIT, ZOOM78 1-694-497-11 TERMINAL BOARD, BATTERY
110 1-418-564-11 RAY-CATCHER BLOCK UNIT,REMOCON112 1-418-192-11 MICROPHONE UNIT122 1-672-514-11 TRANSLATION FLEXIBLE BOARD169 X-3378-951-1 CONTROL SW SUB ASSY, UPPER207 1-959-252-11 HARNESS (GLAY)
208 1-959-251-11 HARNESS (YELLOW)0213 1-517-843-11 FLUORESCENT TUBE
215 1-672-355-11 LCD DETECTION SW FLEXIBLE BOARD221 1-803-445-11 PANEL, TOUCH251 1-672-356-11 VF/LCD FLEXIBLE BOARD
267 1-672-357-11 VF FLEXIBLE BOARD304 8-848-732-01 DEVICE, LENS (LSV-620B)306 1-758-202-21 FILTER BLOCK, OPTICAL408 1-675-950-11 MOTOR FLEXIBLE BOARD409 1-418-191-11 SENSOR, MR
417 1-452-997-11 ENCODER, MAGNETM5811 1-698-543-21 MOTOR (STEPPING)LCD4301 1-803-033-21 INDICATOR MODULE, LIQUID CRYSTALLCD4701 8-753-023-89 LCX024AK-5
************************************************************
**************HARDWARE LIST**************
#1 7-621-591-00 SCREW +K 2X4#2 7-623-505-01 LUG, 2#3 7-628-253-15 SCREW +PS 2X5
************************************************************
6-21 E
VF
ACCESSORIES & PACKING MATERIALS*******************************
0 1-418-327-21 CHARGER, AC ADAPTOR (AC-VQ800)1-418-732-21 REMOTE COMMANDER (RMT-DCM1)1-543-793-11 FILTER, CLAMP (FERRITE CORE) (SMALL)1-543-798-11 FILTER, CLAMP (FERRITE CORE) (LARGE)1-765-080-11 CORD, CONNECTION (STEREO AV) (1.5m)
0 1-790-107-22 CORD, POWER1-790-351-11 CORD, CONNECTION (ZK-ET1) (1.8m)3-742-854-01 LID, BATTERY (for RMT-DCM1)3-866-152-11 MANUAL, INSTRUCTION (ENGLISH)3-866-152-21 MANUAL, INSTRUCTION (FRENCH) (Canadian)
3-987-015-01 BELT (S), SHOULDER4-220-941-01 ATTACHMENT (TRIPOD)
The components identified bymark 0 or dotted line withmark 0 are critical for safety.Replace only with part num-ber specified.
Les composants identifiés par unemarque 0 sont critiques pour lasécurité.Ne les remplacer que par une pièceportant le numéro spécifié.
< PARTS REFERENCE SHEET >You can find the parts position of mount locations applying to MAIN board of a set.
DCM-M1
IC5002
IC5404
IC8101
IC3004
IC8004
IC8601
IC8501
A
B
C
D
E
F
G
H
1 2 3 4 5 6 7 8
87654321
F
G
H
A
B
C
D
E
SIDE A
SIDE B
MAIN DCM–M1
MAIN DCM–M1
– 254 –
DCM-M1
Sony CorporationPersonal Audio Division Company9-927-635-11 1999L05044-1
Printed in Japan C 1999. 12Published by General Engineering Dept.
SERVICE MANUAL
DCM-M1
SUPPLEMENT-1File this supplement with the service manual.
Subject:1. Change of General2. Correction of Schematic Diagram3. Change of repair parts4. Addition of the note about a special tool for ICs.5. Addition of the instruction manual for Argentina
model.
US ModelCanadian Model
E Model
1. Change of General! : Indicates changed portion.
Page Before Change After Change
1-14
$$
2. Correction of Schematic DiagramPage 4-49 to 4-50. Location G to H, 14 to 16.
Incorrect Correct
2000. 03
– 2 –
Sony CorporationPersonal Audio Division Company9-927-635-81 2000C05044-1D
Printed in Japan C 2000. 3Published by General Engineering Dept.
3. Change of repair parts (Section 5 Exploded Views/Section 6 Electrical Parts List)! : Indicates changed portion.
Page Before Change After Change
Ref. No. Part No. Description Remark
A-3323-172-A POWER BOARD ASSYA-3323-173-A JACK BOARD ASSYA-3323-170-A BL BOARD ASSYA-3323-171-A VF BOARD ASSY
312 A-3328-667-A CCD BLOCK ASSY
Ref. No. Part No. Description Remark
A-3321-881-A POWER BOARD, COMPLETEA-3321-883-A JACK BOARD, COMPLETEA-3321-877-A BL BOARD, COMPLETEA-3321-879-A VF BOARD, COMPLETEnot supplied (IC001)
Page IC Page IC
Ref. No. Part No. Description Remark
@IC8005 1-803-635-11 IC WTGA-EKM29U64000-K1@IC8101 8-752-396-85 IC CXD702-102GA@IC8102 8-759-572-71 IC KM416U4104BC-L6@IC8103 8-759-572-71 IC KM416U4104BC-L6@IC8501 8-759-653-48 IC uPD70F3102F1-33-FA1@IC8601 8-752-396-81 IC CXD1405GG
@IC8701 8-752-394-48 IC CXD1404GA
Ref. No. Part No. Description Remark
@IC3009 8-752-397-21 IC CXZ31021GA@IC5301 8-752-397-34 IC CXD2652AGA@IC5403 8-752-390-38 IC CXD606-112GA@IC5404 8-759-676-88 IC RU6815TC-DCMM1
@IC8001 8-759-572-52 IC HD6417709BT80A@IC8002 8-759-572-70 IC KM416S4034CC-C10@IC8003 8-759-572-70 IC KM416S4034CC-C10
6-9
5-2 Ref No. 52/6-155-2 Ref No. 57/6-35-6 Ref No. 252/6-15-6 Ref No. 266/6-195-7
4. Additional of the note about a special tool for ICs. (Electrical Parts List MAIN Board)Note: @ Replacement of the following ICs used in this set requires a special tool.
Therefore, it cannot be replaced.
6-10
6-10
5. Additional of the instruction manual for Argentina model.Page ACCESSORIES & PACKING MATERIALS
Ref. No. Part No. Description Remark
3-866-152-31 MANUAL, INSTRUCTION (SPANISH) (Argentina)6-21
306307
309 310310
311not supplied(IC001)
notsupplied
306307
309 310310
311
312
not supplied(IC001)
notsupplied
$
$
SERVICE MANUAL
DCM-M1
SUPPLEMENT-2File this supplement with the service manual.
Subject:• Addition of Section 7 Adjustments• Correction of Schematic Diagrams
US ModelCanadian Model
E Model
2000. 05
– 2 –
MAIN BOARD IC8005 (Flash) z z
MAIN BOARD IC5405 (NV-RAM) z
VF BOARD IC4502 (D/A CONV.(EVR)) z
LCD BOARD IC4301 (D/A CONV.(EVR)) z
Mecha. Deck Block z
Touch Panel z
*1LCD Block LCD4301 (LCD Panel) z z
EVF Block LCD4701 (LCD Panel) z
• Adjustment items required at the replacement of main parts and boards Adjust the items marked with z in the following table when main parts were replaced.
7. ADJUSTMENTS
For the adjustment of this set, the test mode and the firmware data writing are provided.In the test mode, various adjustment, setting, and checking can be made. Also, the firmware data writing is executed when the Main boarditself, or the Flash Memory (IC8005) or MPEG Control (IC8501) on the Main board is replaced.
TABLE OF CONTENTS
7-1. Test Mode ...................................................................... 31-1. Outline of Test Mode ..................................................... 31-2. EVF System Adjustment ............................................... 51-3. LCD System Adjustment ............................................... 81-4. Servo System Adjustment ............................................. 131-5. MAC Address Setting .................................................... 161-6. Touch Panel Adjustment ............................................... 201-7. Other Checking ............................................................. 21
7-2. Firmware Data Writing Method ..................................... 232-1. Preparation .................................................................... 232-2. Writing to Flash Memory (IC8005) ................................ 262-3. Writing to MPEG Control (IC8501) ............................... 26
Replacement parts
Adjustment items
Table.7-1*1Note: When LCD panel in the LCD block was replaced, first perform the LCD system adjustment, and then the touch panel position
alignment.
EVF SystemAdjustment
LCD SystemAdjustment
Servo SystemAdjustment
MAC AddressSetting
Touch PanelPosition
Alignment
– 3 –
7-1. Test Mode1-1. Outline of Test ModeIn the Test mode, this set allows you to adjust the LCD, EVF,servo, and touch panel and also to set MAC address.
1-1-1. Equipment UsedIn performing the LCD, EVF, and servo adjustment, use the fol-lowing measuring instruments.
EVF and LCD system adjustment• Oscilloscope
Dual-trace oscilloscope, band over 30MHz, and delay mode(Use 10:1 probe unless otherwise specified)
• Frequency counter• Digital voltmeter• Adjusting monitor jig
Part code: J-2053-017-A
Servo system adjustment• MD1 High reflectance pre-mastered disc (TDYS-1)
Part code: 4-963-646-01• MD1 MO disc
Commercially available SONY MD1 MO disc(already recorded)
• MD2 MO discCommercially available SONY MD2 MO disc
1-1-2. How to Enter the Test ModeIn the normal mode, set the POWER switch to “CAMERA”.While pressing u key on the set, press >, >, ., .,e, E, e, E, y, y keys on the set in this order.The Test Mode screen (Fig.7-1-1) appears on the LCD and theTest mode becomes active.
Fig.7-1-1
1-1-3. How to Exit from the Test ModeTurn the power off.Note: In the Test mode, the POWER switch is inactive and there-
fore disconnect AC adapter to turn the power off.
TEST MODE
Camera
made by MD dep.
I TRON Ver. s. sssDrive Ver. s. sssJAVA APP Ver. ssssssssJAVA OS Ver. ssssssssBOOT Ver. s. sss I PL Ver. s. sssRATE CTL Ver. s. sss
Item No. 1–00–00
1-1-4. Description of Test Mode Screen
Fig.7-1-2
1) Version display fieldThe versions of respective programs that compose the set aredisplayed.ITON ............ Version of set programDrive ............. Version of drive programJAVA APP ..... Version of JAVA applicationJAVA OS....... Date when JAVA OS was releasedBOOT ........... Version of BOOT programIPL ................ Version of IPL programRATE CTL ... Version of V850 (IC8501 on Main board)
program
2) Test mode item number display field
Fig.7-1-3
Current Test mode item number is used.The Test mode items are composed of a major item, mediumitem, and minor item.The number displayed in blue is currently active item.
3) Test mode item name display field
Fig.7-1-4
Major item, medium item, and minor item of current test modeitem are displayed respectively.
TEST MODE
Drive
0790
made by MD dep.
I TRON Ver. s. sssDrive Ver. s. sssJAVA APP Ver. ssssssssJAVA OS Ver. ssssssssBOOT Ver. s. sss I PL Ver. s. sssRATE CTL Ver. s. sss
Item No.
Function code change
4–01–01
Of fse t
: 6C0 DATA : 00 00 00 30 00 00 00 00
Version display field
Test mode item number display field
Adjustment data and adjustment status display field Special data
display field
Test mode item name display field
Item No. 4–01–01
Major item number
Minor item numberMedium item number
DriveFunction code change
Of fse t
Minor item name
Major item name Medium item name
– 4 –
4) Adjustment data and adjustment status display fieldFor the items in which there are adjustment data, the data be-ing adjusted is displayed.In the EVF and LCD adjustment, ifdata are written, the characters are displayed in violet. At thewhite balance adjustment in the EVR and LCD adjustment,“R” or “B” in small size is displayed on the side of data.Also, for automatic adjustment items such as servo auto ad-justment among the items in which there is no adjustment data,“Adjusting”, “OK”, or “NG” is displayed.
5) Special data display fieldOnly the minor item for Drive and Servo adjustment is dis-played. RAM value of address on the drive side is periodicallyread and displayed.
1-1-5. Key Operation in Test ModeIn the Test mode, use the keys on the set for operation.1. Change or setting of test mode items
• Movement over active item numbers (u, x keys)
Fig.7-1-5
Use u key when setting active item number and movingto lower level, or use x key when canceling current itemand moving to higher level.
• Change of active item number (>, ., u keys)Use > key to raise active item number, or . key tolower it. For a minor item of Drive and Servo adjustment,use u key to change the item number.
• Execution or cancellation of active item (y, x keys)For automatic adjustment items such as servo auto adjust-ment, pressing y key executes automatic adjustment. Tocancel automatic adjustment, press x key.
2. Change or writing of adjustment dataFor the items of LCD and EVF adjustment in which there areadjustment data, the data can be changed or written by a keyoperation.
• Change of adjustment data (e, E keys)Use e key to increase the adjustment data, or E key toreduce it.
• Writing of adjustment data (y key)Pressing y key causes the adjustment data to be written tononvolatile memory.At this time, the displayed adjustment data characterschanges to violet in color. (Unless this operation is per-formed, new adjustment data are not stored in nonvolatilememory)
3. Switching of screen displayThe LCD and EVF adjustment contains the items that requirethe screen display to be switched to the test signal screen.• Color bar display method (MENU key)
When major item is in the LCD state (item number: 3), pressthe MENU key, and the screen display will be switched tothe color bar display.To return to the test mode screen, press the MENU key oncemore.
• 10-step gradation pattern display method (DSPL key)Press the DSPL key, and the screen display will be switchedas shown below. (Except Drive and Servo items)
• 10-step gradation pattern setting method (MENU key)When major item is in the EVF state (item number: 2) andthe 10-step gradation pattern screen is displayed, press theMENU key, and the screen will be switched to the 10-stepgradation pattern (green) display. Pressing the MENU keyonce more causes the screen to be switched to the 10-stepgradation pattern (white/black) display. If this setting is notmade, the 10-step gradation pattern screen is switched tothe camera-through screen.
1-1-6. Test Mode ConfigurationThe Test mode (major item) is composed of the following items.
Camera (item number: 1) ... Not used.EVF (item number: 2) ........ Use for EVF system adjustment.LCD (item number: 3) ........ Use for LCD system adjustment.Drive (item number: 4) ....... Use for checking if an error
occurredin Servo system adjust-ment.
Audio (item number: 5) ..... Not used.Power (item number: 6) ..... Not used.Other (item number: 7) ...... Use for touch panel adjustment,
MAC address setting, or otherchecking.
Servo (item number: 8) ...... Use for Servo system adjustment.
Item No. 4–01–01u key moving
x key moving
Test mode screen
10-step gradation pattern screen(Set in “EVF” item)
Camera-through screen
– 5 –
[Connector for adjustment]The measurement points for EVF adjustment are concentrated onthe CN4901 on the VF board. Connect a measuring instrument toit via adjusting monitor jig (J-2503-017-A).The following table lists the pin No. and signal name of CN4901.
Pin No.
VF board Adjustment Signal nameCN4901 monitor jig
5 A EVF_GND
4 B G
3 C EVF_BL_4.95V (–)
2 D EVF_BL_4.95V
1 E VCO
– F NC
– G NC
– H NC
– I NC
– J NC
Table.7-1-1
1-2. EVF System AdjustmentNote 1: The backlight (fluorescent tube) is driven with high volt-
age AC power. Accordingly, do not touch the backlightholder; otherwise you could receive an electric shock.
Note 2: Take extreme care not to destroy the LCD unit by staticelectricity, when replacing it.
Note 3: On the Menu screen, set the “Finder Brightness” to thecenter.
Note 4: Once the 10-step gradation pattern (white/black) has beenset, it is held until the power is turned off. Therefore, itis not necessarily set every time in successive adjust-ment.
[Adjustment steps]The EVF adjustment, as a rule, should be performed following thesteps given below.Only for the “Backlight Consumed Current Adjustment”, the or-der may be changed.1. EVF Adjustment Data Initializing2. VCO Adjustment3. Brightness Adjustment4. Contrast Adjustment5. Backlight Consumed Current Adjustment6. White Balance Adjustment
Fig.7-1-6
Use the connector with EVF labeling.
VF board CN4901
1
5
ABCDEFGHIJ
Adjusting monitor jig (J-2503-017-A)
– 6 –
1. EVF Adjustment Data Initializing
Item number 2-03-01
Screen display Test mode screen
Adjusting method1) Select the item number “2-03-01”.2) Press y key to execute the adjustment data initializing.
Check that “OK!” is displayed on the test mode screen.3) Move to the item number “2-01-ss”, and check that the ad-
justment data of each minor item is initial value. (See the fol-lowing table)
Item No. Initial Data Minor item name
2-1-1 83 VCO adjustment
2-1-2 90 BRIGHT adjustment
2-1-3 B5 CONTRAST adjustment
2-1-4 B8 Back Light adjustment
2-1-5 R data: 97 White balance adjustmentB data: 57
Table.7-1-2
Note: To switch between R data and B data of “White BalanceAdjustment”, press u key. After checking the data, moveto other item with R data kept displayed.
2. VCO AdjustmentSet free running frequency of VCO.
Item number 2-01-01
Screen display Arbitrary
Measurement point Adjusting monitor jig E pin (VCO)
Measuring instrument Oscilloscope (DC range)
Adjustment data 83initial value
Adjustment value A = 1.80 ± 0.05 V
Adjusting method1) Select the item number “2-01-01”.2) Check the GND level of oscilloscope.3) Using e and E keys, change the adjustment data so that the
VCO output voltage (A) satisfies the adjustment value.4) Press y key to write the adjustment data.
Fig.7-1-7
H
A
GND level (0Vdc)
3. Brightness AdjustmentSet the VIDEO signal level that drives the LCD (of EVF) to propervalue.If deviated, the EVF screen will be unclear, black blurring, or whiteblurring.
Item number 2-01-02
Screen display Arbitrary
Measurement point Adjusting monitor jig B pin (G)
Measuring instrument Oscilloscope
Adjustment data 90initial value
Adjustment value A = 7.1 ± 0.1 Vp-p
Adjusting method1) Select the item number “2-01-02”.2) Using e and E keys, change the adjustment data so that the
voltage (A) between pedestal of inverted waveform and ped-estal of non-inverted waveform satisfies the adjustment value.
3) Press y key to write the adjustment data.
Fig.7-1-8
2H
Pedestal
Pedestal
A
– 7 –
4. Contrast AdjustmentSet the VIDEO signal level that drives the LCD to proper value.If deviated, the EVF screen will be unclear, black blurring, or whiteblurring.
Item number 2-01-03
Screen display 10-step gradation pattern (white/black)
Measurement point Adjusting monitor jig B pin (G)
Measuring instrument Oscilloscope
Adjustment data B5initial value
Adjustment value A = 2.1 ± 0.1 Vp-p
Adjusting method1) Set the 10-step gradation pattern (white/black).2) Select the item number “2-01-03”.3) Press the DSPL key to display the 10-step gradation pattern
(white/black) on the EVF screen.4) Using e and E keys, change the adjustment data so that the
voltage (A) between pedestal (0 IRE) and 100 IRE satisfiesthe adjustment value.
5) Press y key to write the adjustment data.6) Press the DSPL key to return the EVF screen to the test mode
screen.
Fig.7-1-9
5. Backlight Consumed Current AdjustmentSet the brightness of backlight.If deviated, the picture will be too dark or too bright.
Item number 2-01-04
Screen display 10-step gradation pattern (white/black)
Measurement point + probe: Adjusting monitor jig D pin(BL+)
– probe: Adjusting monitor jig C pin(BL–)
Measuring instrument Digital voltmeter
Adjustment data B8initial value
Adjustment value A = 21.0 ± 1.0 mV
Note: After turning on the power, wait for more than 30 seconds,and then start the adjustment.
Adjusting method1) Set the 10-step gradation pattern (white/black).2) Select the item number “2-01-04”.3) Press the DSPL key to display the 10-step gradation pattern
(white/black) on the EVF screen.4) Using e and E keys, change the adjustment data so that po-
tential difference (A) between adjusting monitor jig D pin(BL+) and C pin (BL–) satisfies the adjustment value.
5) Press y key to write the adjustment data.6) Press the DSPL key to return the EVF screen to the test mode
screen.
A
100 IRE
Pedestal(0 IRE)
2H
6. White Balance AdjustmentAdjust the white balance properly.If deviated, the color reproducibility of EVF screen will be poor.
Item number 2-01-05
Screen display 10-step gradation pattern (white/black)
Measurement point Check on the EVF screenMeasuring instrument
Adjustment data R data: 97initial value B data: 57
Adjustment value EVF screen must not be colored
Note: To switch between R data and B data, press u key.After the adjustment finished, move to other item with Rdata kept displayed.
Adjusting method1) Set the 10-step gradation pattern (white/black).2) Select the item number “2-01-05”.3) Set the adjustment data to initial value (R data:97, B data:57).Note: Each time the data is set, press y key to write data to
nonvolatile memory.4) Press the DSPL key to display the 10-step gradation pattern
(white/black) on the EVF screen.5) Check that the EVF screen is not colored.
If colored, change the adjustment data by using e and E keysso that the EVF screen is not colored.
Note: Each time the data is set, press y key to write data tononvolatile memory.
6) Press the DSPL key to return the EVF screen to the test modescreen.
– 8 –
[Connector for adjustment]The measurement points for LCD adjustment are concentrated onthe CN4305 on the LCD board.Connect a measuring instrument to it via adjusting monitor jig(J-2503-017-A).The following table lists the pin No. and signal name of CN4305.Use the connector with LCD labeling.
Pin No.
LCD board Adjustment Signal nameCN4305 monitor jig
9 A XTST
8 B SYF
7 C HSY
6 D PANEL_XHD
5 E GND
4 F PANEL_COM
3 G VG
2 H BL (+)
1 I BL (–)
– J NC
Table.7-1-3
LCD board CN4305
9 1
Use the connector with LCD labeling.
Adjusting monitor jig (J-2503-017-A)
ABCDEFGHIJ
Fig.7-1-10
1-3. LCD System AdjustmentNote 1: The backlight (fluorescent tube) is driven with high volt-
age AC power. Accordingly, do not touch the backlightholder; otherwise you could receive an electric shock.
Note 2: Take extreme care not to destroy the LCD unit by staticelectricity, when replacing it.
Note 3: On the Menu screen, set the “Panel Brightness” and“Panel Color Density” to the center.
Note 4: Once the 10-step gradation pattern (white/black) has beenset, it is held until the power is turned off. Therefore, itis not necessarily set every time in successive adjust-ment.
[Adjustment steps]The LCD adjustment, as a rule, should be performed followingthe steps given below.Only for the “Backlight Consumed Current Adjustment”, the or-der may be changed.1. LCD Adjustment Data Initializing2. VCO Adjustment3. Horizontal Position Adjustment4. RGB D Range Adjustment5. Brightness Adjustment6. Contrast Adjustment7. V-COM Level Adjustment8. Color Adjustment9. V-COM Adjustment10. Backlight Consumed Current Adjustment11. White Balance Adjustment
– 9 –
1. LCD Adjustment Data Initializing
Item number 3-03-01
Screen display Test mode screen
Adjusting method1) Select item number “3-03-01”.2) Press y key to execute the adjustment data initializing.
Check that “OK!” is displayed on the test mode screen.3) Move to the item number “3-01-ss”, and check that the ad-
justment data of each minor item is initial value. (See the fol-lowing table)
Item No. Initial Data Minor item name
3-1-1 BF VCO adjustment
3-1-2 5D Flat Position adjustment
3-1-3 80 RGB D-range adjustment
3-1-4 7C BRIGHT adjustment
3-1-5 D5 CONTRAST adjustment
3-1-6 A8 V-COM level adjustment
3-1-7 76 COLOR adjustment
3-1-8 9C V-COM adjustment
3-1-9 B6 Back Light adjustment
3-1-A R data: 95 White balance adjustmentB data: 70
Table.7-1-4
Note: To switch between R data and B data of “White BalanceAdjustment”, press u key. After checking the data, moveto other item with R data kept displayed.
2. VCO AdjustmentSet free running frequency of VCO.
Item number 3-01-01
Screen display Arbitrary
Measurement point Adjusting monitor jig C pin (HSY)
Measuring instrument Frequency counter
Adjustment data BF initial value
Adjustment value f = 15734 ± 30 Hz
Adjusting method1) Select the item number “3-01-01”.2) Connect the adjusting monitor jig B pin (SYF) and E pin
(GND).3) Using e and E keys, change the adjustment data so that the
VCO frequency (f) satisfies the adjustment value.4) Press y key to write the adjustment data.5) Disconnect the adjusting monitor jig B pin (SYF) and E pin
(GND).
3. Horizontal Position AdjustmentAdjust the display position on LCD panel properly.
Item number 3-01-02
Screen display Color bar
Measurement point CH1: Adjusting monitor jig D pin(PANEL XHD)
CH2: Adjusting monitor jig C pin(HSY)
Measuring instrument Oscilloscope
Adjustment data 5Dinitial value
Adjustment value T = 0.65 ± 0.1 µsec
Adjusting method1) Select the item number “3-01-02”.2) Press the MENU key to display color bar on the LCD screen.3) Using e and E keys, change the adjustment data so that the
falling time difference (T) between PANEL XHD signal andHSY signal satisfies the adjustment value.
4) Press y key to write the adjustment data.5) Press the MENU key to return the LCD screen to the test mode
screen.
Fig.7-1-11
CH1
CH2
CH1
CH2
T
enlargement
– 10 –
5. Brightness AdjustmentSet the VIDEO signal level that drives the LCD to proper value.If deviated, the LCD screen will be unclear, black blurring, or whiteblurring.
Item number 3-01-04
Screen display 10-step gradation pattern (white/black)
Measurement point Adjusting monitor jig G pin (VG)
Measuring instrument Oscilloscope
Adjustment data 7Cinitial value
Adjustment value A = 1.40 ± 0.05 Vp-p
Note: This is the tracking adjustment in relation to “6. ContrastAdjustment”.
Adjusting method1) Select major item number “2” (EVF), and set the 10-step gra-
dation pattern (white/black).2) Select the item number “3-01-04”.3) Press the DSPL key to display the 10-step gradation pattern
(white/black) on the LCD screen.4) Connect the adjusting monitor jig A pin (XTST) and E pin
(GND).5) Using e and E keys, change the adjustment data so that the
voltage (A) between pedestal (0 IRE) and GAMMA1 limiterlevel satisfies the adjustment value.
6) Press y key to write the adjustment data.7) Disconnect the adjusting monitor jig A pin (XTST) and E
pin (GND).8) Press the DSPL key to return the LCD screen to the test mode
screen.9) Check that the adjustment value of “Contrast Adjustment” is
satisfied.If not satisfied, perform “Contrast Adjustment”.
Fig.7-1-13
Pedestal(0 IRE)
GAMMA1 limiter level
A
2H
4. RGB D Range AdjustmentSet the D range of RGB decoder driver step-wise output that drivestheLCD to proper value.If deviated, the LCD screen will be black blurring or white blur-ring.
Item number 3-01-03
Screen display 10-step gradation pattern (white/black)
Measurement point Adjusting monitor jig G pin (VG)
Measuring instrument Oscilloscope
Adjustment data 80initial value
Adjustment value A = 3.00 ± 0.05 Vp-p
Adjusting method1) Select major item number “2” (EVF), and set the 10-step gra-
dation pattern (white/black).2) Select the item number “3-01-03”.3) Press the DSPL key to display the 10-step gradation pattern
(white/black) on the LCD screen.4) Using e and E keys, change the adjustment data so that the
voltage (A) between pedestal of inverted waveform and ped-estal of non-inverted waveform satisfies the adjustment value.
5) Press y key to write the adjustment data.6) Press the DSPL key to return the LCD screen to the test mode
screen.
Fig.7-1-12
2H
Pedestal
Pedestal
A
– 11 –
6. Contrast AdjustmentSet the VIDEO signal level that drives the LCD to proper value.If deviated, the LCD screen will be unclear, black blurring, or whiteblurring.
Item number 3-01-05
Screen display 10-step gradation pattern (white/black)
Measurement point Adjusting monitor jig G pin (VG)
Measuring instrument Oscilloscope
Adjustment data D5initial value
Adjustment value A = 2.54 ± 0.05 Vp-p
Note: This is the tracking adjustment in relation to “5. Bright-ness Adjustment”.
Adjusting method1) Select major item number “2” (EVF), and set the 10-step gra-
dation pattern (white/black).2) Select the item number “3-01-05”.3) Press the DSPL key to display the 10-step gradation pattern
(white/black) on the LCD screen.4) Using e and E keys, change the adjustment data so that the
voltage (A) between pedestal (0 IRE) and 100 IRE satisfiesthe adjustment value.
5) Press y key to write the adjustment data.6) Press the DSPL key to return the LCD screen to the test mode
screen.7) Check that the adjustment value of “Brightness Adjustment”
is satisfied.If not satisfied, perform “Brightness Adjustment”.
Fig.7-1-14
Pedestal(0 IRE)
100 IRE
A
2H
7. V-COM Level AdjustmentSet common electrode drive signal level of the LCD panel to propervalue.
Item number 3-01-06
Screen display 10-step gradation pattern (white/black)
Measurement point Adjusting monitor jig F pin(PANEL COM)
Measuring instrument Oscilloscope
Adjustment data A8initial value
Adjustment value A = 4.95 ± 0.05 Vp-p
Adjusting method1) Select major item number “2” (EVF), and set the 10-step gra-
dation pattern (white/black).2) Select the item number “3-01-06”.3) Press the DSPL key to display the 10-step gradation pattern
(white/black) on the LCD screen.4) Using e and E keys, change the adjustment data so that the
V-COM signal level satisfies the adjustment value.5) Press y key to write the adjustment data.6) Press the DSPL key to return the LCD screen to the test mode
screen.
Fig.7-1-15
A
2H
– 12 –
9. V-COM AdjustmentSet DC bias of common electrode drive signals for the LCD panelto proper value.If deviated, the LCD screen will be unstable where flickering orvertical streaks appear.
Item number 3-01-08
Screen display Test mode screen
Measurement point Check on LCD screenMeasuring instrument
Adjustment data 9Cinitial value
Adjustment value Fig. 7-1-17
Note: This adjustment must be performed after performing“Brightness Adjustment” and “Contrast Adjustment”.
Adjusting method1) Select the item number “3-01-08”.2) Set the adjustment data to initial value (9C).3) Check that the density of character “e” on the LCD screen is
same (see Fig. 7-1-17). If different, change the adjustment databy using e and E keys so as to attain the same density ofcharacter “e”.
4) Press y key to write the adjustment data.
Fig.7-1-17
TEST MODE
LCD Panel
9C
made by MD dep.
I TRON Ver. s. sssDrive Ver. s. sssJAVA APP Ver. ssssssssJAVA OS Ver. ssssssssBOOT Ver. s. sss I PL Ver. s. sssRATE CTL Ver. s. sss
Item No.
V–COM adjst
3–01–08
Adus t
NGOK
enlargement
NG
8. Color AdjustmentSet the color density to the specified value.If deviated, the color will be too dark or too light.
Item number 3-01-07
Screen display Color bar
Measurement point Adjusting monitor jig G pin (VG)
Measuring instrument Oscilloscope
Adjustment data 76initial value
Adjustment value A = 0.15 ± 0.05 Vp-p
Adjusting method1) Select the item number “3-01-07”.2) Press the MENU key to display color bar on the LCD screen.3) Using e and E keys, change the adjustment data so that a
difference (A) between white signal level and green signal levelsatisfies the adjustment value.
4) Press y key to write the adjustment data.5) Press the MENU key to return the LCD screen to the test mode
screen.
Fig.7-1-16
Green
White
A
2H
– 13 –
10. Backlight Consumed Current AdjustmentSet the brightness of backlight.If deviated, the picture will be too dark or too bright.
Item number 3-01-09
Screen display Color bar
Measurement point + probe: Adjusting monitor jig I pin (BL+)
_ probe: Adjusting monitor jig H pin (BL–)
Measuring instrument Digital voltmeter
Adjustment data B6initial value
Adjustment value A = 66.0 ± 1.0 mV
Note: Use AC adapter whenever performing this adjustment.After turning on the power, wait for more than 30 seconds,and then start the adjustment.
Adjusting method1) Select the item number “3-01-09”.2) Press the MENU key to display color bar on the LCD screen.3) Using e and E keys, change the adjustment data so that po-
tential difference (A) between adjusting monitor jig I pin(BL+) and H pin (BL–) satisfies the adjustment value.
4) Press y key to write the adjustment data.5) Press the MENU key to return the LCD screen to the test mode
screen.
11. White Balance AdjustmentAdjust the white balance properly.If deviated, the color reproducibility of LCD screen will be poor.
Item number 3-01-0A
Screen display 10-step gradation pattern (white/black)
Measurement point Check on the LCD screenMeasuring instrument
Adjustment data R data: 95initial value B data: 70
Adjustment value LCD screen must not be colored
Note: To switch between R data and B data, press u key.After the adjustment finished, move to other item with Rdata kept displayed.
Adjusting method1) Select major item number “2” (EVF), and set the 10-step gra-
dation pattern (white/black).2) Select the item number “3-01-0A”.3) Set the adjustment data to initial value (R data:95, B data:70).
Note: Each time the data is set, press y key to write data tononvolatile memory.
4) Press the DSPL key to display the 10-step gradation pattern(white/black) on the LCD screen.
5) Check that the LCD screen is not colored.If colored, change the adjustment data by using e and E keysso that the LCD screen is not colored.Note: Each time the data is set, press y key to write data to
nonvolatile memory.6) Press the DSPL key to return the LCD screen to the test mode
screen.
1-4. Servo System Adjustment1. Servo Auto AdjustmentThe servo auto adjustment is executed automatically so that theadjustment data of the servo system meets the optical pick-up blockin that set.The servo auto adjustment checks the type of inserted disc andexecutes automatically the adjustment that meets the inserted disc.If the optical pick-up block or IC5405 on the Main board wasreplaced, perform the servo auto adjustment with the followingthree types of discs respectively.
• MD1 High reflectance pre-mastered disc (TDYS-1)Part code: 4-963-646-01
• MD1 MO discCommercially available SONY MD1 MO disc (already recorded)
• MD2 MO discCommercially available SONY MD2 MO disc
Adjusting method1) Select the item number “8-01-01”.2) Insert the desired type of disc to be adjusted.3) Press y key to execute the servo auto adjustment. (Auto ad-
justment will start and “Now Adjusting ... ss” will be dis-played in the adjustment status display field.)Note: Place the set horizontally and perform adjustment un-
der stable condition.
Fig.7-1-18
4) At the completion of adjustment, the adjustment result will bedisplayed in the adjustment status display field.Note: If an error occurs during adjustment, you can check
the item name where the error occurred. (Refer to“Faulty item checking method”.)
Fig.7-1-19
5) Remove the disc inserted in step 2).
TEST MODE
Servo
made by MD dep.
I TRON Ver. s. sssDrive Ver. s. sssJAVA APP Ver. ssssssssJAVA OS Ver. ssssssssBOOT Ver. s. sss I PL Ver. s. sssRATE CTL Ver. s. sss
Item No.
All Adjust START
Now Adjusting . . . ss
8–01–01
Servo Common
: 6C0 DATA : 00 00 00 30 00 00 00 00
Adjustment status display field
NG
OK!
NG. ss ss
• In case of successful adjustment
• In case of NG adjustment
A
– 14 –
Faulty item checking method1) From the adjustment status display screen at “NG” (Fig.7-1-
19), read a 2-digit number at part “A”.Example: On the following screen, if adjustment finished, “78” is
displayed.
Fig.7-1-20
2) Move over major item to Drive (item number: 4).3) Set medium item number to higher digit of the number read in
step 1).Example: If the read number is “78”, medium item number is 7.4) Set minor item number to lower digit of the number read in
step 1).At this time, the medium item name and minor item name onthe screen indicate the adjustment item names where an erroroccurred during servo auto adjustment.
Example: If the read number is “78”, minor item number is 8.
Fig.7-1-21
Then, from the medium item name and minor item name, youcan confirm that a fault occurred in “MD1 GRV F-BIAS(ADIP)” item of the “MD1 GRV adj”.
TEST MODE
Servo
made by MD dep.
I TRON Ver. s. sssDrive Ver. s. sssJAVA APP Ver. ssssssssJAVA OS Ver. ssssssssBOOT Ver. s. sss I PL Ver. s. sssRATE CTL Ver. s. sss
Item No.
All Adjust START
8–01–01
Servo Common
: 6C0 DATA : 00 00 00 30 00 00 00 00NG NG. 78 ss
TEST MODE
Drive
0790
made by MD dep.
I TRON Ver. s. sssDrive Ver. s. sssJAVA APP Ver. ssssssssJAVA OS Ver. ssssssssBOOT Ver. s. sss I PL Ver. s. sssRATE CTL Ver. s. sss
Item No.
MD1 GRV F-BIAS (ADIP)
4–07–08
MD1 GRV adj
: 6C0 DATA : 00 00 00 30 00 00 00 00
– 15 –
2. Mecha. Deck Block Primary CheckThe following parts of the mecha. deck block can be checked in asimple check.• Laser diode• Focus coil• Spindle motor• Disc type check switch• Sled motor• Tracking coil• INITIAL SW• HEAD UP/DOWN motor• INITIAL SW
Note: To check the operation of mecha. deck block, remove theUpper Panel Assembly. (See 2. Removal on page 2-9)
Checking method1) In the normal mode, set the POWER switch to “CAMERA”.2) Check that “DISC LID IS OPEN” is displayed on the LCD
screen.3) Press the part A to check that the part B lights in red and
moves up and down. (Laser diode check, Focus coil check)Also, check that the spindle motor rotates at this time. (Spindlemotor check)
Note: If the part A is released once and then pressed again, theoperation restarts though the operation time is short.
MD1/MD2
PIT/GRV
PROTECT SW
Spindle MotorOPTICAL PICK-UP block
B
C
A
D
X
NOTES ON HANDLING THE OPTICAL PICK-UPBLOCK OR BASE UNIT
The laser diode in the optical pick-up block may suffer electro-static break-down because of the potential difference generatedby the charged electrostatic load, etc. on clothing and the humanbody.During repair, pay attention to electrostatic break-down and alsouse the procedure in the printed matter which is included in therepair parts.The flexible board is easily damaged and should be handled withcare.
NOTES ON LASER DIODE EMISSION CHECK
The laser beam on this model is concentrated so as to be focusedon the disc reflective surface by the objective lens in the opticalpick-up block. Therefore, when checking the laser diode emis-sion, observe from more than 30 cm away from the objective lens.
Fig.7-1-22
– 16 –
4) Operating the keys on the set, enter the Test mode.5) Select the item “7-02-01” and press u key to activate the
Switch Check mode.Note: When the Switch Check mode becomes active, the
screen as shown in Fig.7-1-23 appears.
Fig.7-1-23
6) Press each switch at part C to check that the mecha. deckswitch status display on the LCD screen changes as listed be-low. (Disc type check switch)
Switch name When not pressed When pressed
MD1/MD2 MD2 MD1
PIT/GRV GRV PIT
PROTECT SW ON OFF
Table 7-1-5
7) Check that the Optical Pick-up block moves outward when> key is pressed, or it moves inward when . key ispressed. (Sled motor check)
8) At this time, check that the part B also moves in the samedirection as the direction in which the Optical Pick-up blockmoves. (Tracking coil check)
9) Check that when the Optical Pick-up block moves inward asfar as it will go, the IN LIMIT SW status display on the LCDscreen is “ON” and when it moves outward, the switch be-comes “OFF”. (IN LIMIT SW check)
10) Check that the part D moves in arrow direction when y keyis pressed, and it returns to original position when y key ispressed once more. (HEAD UP/DOWN motor check)
11) At this time, check that each time the y key is pressed, theINITIAL SW status display on the LCD screen changes overbetween “ON” and “OFF”. (INITIAL SW check)
12) Turn the power off.Note: Disconnect the AC adapter to turn the power off, be-
cause the POWER switch is inactive in the Test mode.
SW CHECK MODE
REVERSE/CLOSE
COVER CLOSEOFFEJECT SW
IN LIMIT SW INITIAL SWMD1/MD2PIT/GRVPROTECT SW
OFFOFFMD2GRVON
LCD
Mecha. deck switch status display
Set switch status display
LCD switch status display
1-5. MAC Address SettingThe MAC address must be unique in the world.On this set, hexadecimal MAC address is set for every serial num-ber of the set.
1. How to Get MAC Address1) Read the lower 5 digits of serial No. and add “291903 (deci-
mal)” to it, which is assumed to be D1.D1 = “Lower 5 digits of serial No.” + 291903Example: If the lower 5 digits of serial No. is “03574”
D1 = 3574 + 291903 = 2954772) From Table 7-1-6, obtain D2 and H1 that correspond to D1
Example: If D1 = 295477D2 = 295477 – 262144 = 33333H1 = 04
D1 (decimal) D2 (decimal) H1 (hexadecimal)
327679 or less D1-262144 04
327680 or more D1-327680 05
Table 7-1-6
3) From Table 7-1-7, obtain maximum decimal number not ex-ceeding D2, which is assumed to be D3.Example: If D2 = 33333
D3 = 332804) From Table 7-1-7, obtain hexadecimal number that corresponds
to D3, and the higher 2 digits of that number is assumed to beH3.Example: If D3 = 33280
H3 = 825) Obtain a difference between D2 and D3, which assumed to be
D4. (0 ≤ D4 ≤ 255)D4 = D2 – D3
Example: If D2 = 33333 and D3 = 33280,D4 = 33333 – 33280 = 53
6) From Table 7-1-8, convert D4 into hexadecimal number to ob-tain H4.Example: If D4 = 53
H4 = 357) The MAC address is “08:00:46:H1:H3:H4”. (08, 00, 46 are fixed
values)Example: If H1 = 04, H3 = 82 and H4 = 35
08:00:46:04:82:35
– 17 –
Note: D3: DecimalH3: Hexadecimal
Table 7-1-7
D3 H3 D3 H3 D3
0 0000 8192 2000 16384 4000 24576 6000 32768 8000 40960 A000 49152 C000 57344 E000
256 0100 8448 2100 16640 4100 24832 6100 33024 8100 41216 A100 49408 C100 57600 E100
512 0200 8704 2200 16896 4200 25088 6200 33280 8200 41472 A200 49664 C200 57856 E200
768 0300 8960 2300 17152 4300 25344 6300 33536 8300 41728 A300 49920 C300 58112 E300
1024 0400 9216 2400 17408 4400 25600 6400 33792 8400 41984 A400 50176 C400 58368 E400
1280 0500 9472 2500 17664 4500 25856 6500 34048 8500 42240 A500 50432 C500 58624 E500
1536 0600 9728 2600 17920 4600 26112 6600 34304 8600 42496 A600 50688 C600 58880 E600
1792 0700 9984 2700 18176 4700 26368 6700 34560 8700 42752 A700 50944 C700 59136 E700
2048 0800 10240 2800 18432 4800 26624 6800 34816 8800 43008 A800 51200 C800 59392 E800
2304 0900 10496 2900 18688 4900 26880 6900 35072 8900 43264 A900 51456 C900 59648 E900
2560 0A00 10752 2A00 18944 4A00 27136 6A00 35328 8A00 43520 AA00 51712 CA00 59904 EA00
2816 0B00 11008 2B00 19200 4B00 27392 6B00 35584 8B00 43776 AB00 51968 CB00 60160 EB00
3072 0C00 11264 2C00 19456 4C00 27648 6C00 35840 8C00 44032 AC00 52224 CC00 60416 EC00
3328 0D00 11520 2D00 19712 4D00 27904 6D00 36096 8D00 44288 AD00 52480 CD00 60672 ED00
3584 0E00 11776 2E00 19968 4E00 28160 6E00 36352 8E00 44544 AE00 52736 CE00 60928 EE00
3840 0F00 12032 2F00 20224 4F00 28416 6F00 36608 8F00 44800 AF00 52992 CF00 61184 EF00
4096 1000 12288 3000 20480 5000 28672 7000 36864 9000 45056 B000 53248 D000 61440 F000
4352 1100 12544 3100 20736 5100 28928 7100 37120 9100 45312 B100 53504 D100 61696 F100
4608 1200 12800 3200 20992 5200 29184 7200 37376 9200 45568 B200 53760 D200 61952 F200
4864 1300 13056 3300 21248 5300 29440 7300 37632 9300 45824 B300 54016 D300 62208 F300
5120 1400 13312 3400 21504 5400 29696 7400 37888 9400 46080 B400 54272 D400 62464 F400
5376 1500 13568 3500 21760 5500 29952 7500 38144 9500 46336 B500 54528 D500 62720 F500
5632 1600 13824 3600 22016 5600 30208 7600 38400 9600 46592 B600 54784 D600 62976 F600
5888 1700 14080 3700 22272 5700 30464 7700 38656 9700 46848 B700 55040 D700 63232 F700
6144 1800 14336 3800 22528 5800 30720 7800 38912 9800 47104 B800 55296 D800 63488 F800
6400 1900 14592 3900 22784 5900 30976 7900 39168 9900 47360 B900 55552 D900 63744 F900
6656 1A00 14848 3A00 23040 5A00 31232 7A00 39424 9A00 47616 BA00 55808 DA00 64000 FA00
6912 1B00 15104 3B00 23296 5B00 31488 7B00 39680 9B00 47872 BB00 56064 DB00 64256 FB00
7168 1C00 15360 3C00 23552 5C00 31744 7C00 39936 9C00 48128 BC00 56320 DC00 64512 FC00
7424 1D00 15616 3D00 23808 5D00 32000 7D00 40192 9D00 48384 BD00 56576 DD00 64768 FD00
7680 1E00 15872 3E00 24064 5E00 32256 7E00 40448 9E00 48640 BE00 56832 DE00 65024 FE00
7936 1F00 16128 3F00 24320 5F00 32512 7F00 40704 9F00 48896 BF00 57088 DF00 65280 FF00
H3 D3 H3 D3 H3 D3 H3 D3 H3 D3 H3
– 18 –
Table 7-1-8
Hexadecimal-decimal Conversion TableLower digit ofhexadecimal
Upper digit of hexadecimal
0 1 2 3 4 5 6 7 8 9 A(A)
B(b)
C(c)
D(d)
E(E)
F(F)
0
1
2
3
4
5
6
7
8
9
A (A)
B (b)
C (c)
D (d)
E (E)
F (F)
0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15
16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31
32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47
48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63
64 65 66 67 68 69 70 71 72 73 74 77 76 77 78 79
80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95
96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111
112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127
128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143
144 145 146 147 148 149 150 151 152 153 154 155 156 157 158
174
159
175160 161 162 163 164 165 166 167 168 169 170 171 172 173
177176 178 179 180 181 182 183 184 185 186 187 188 189 190 191
192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207
208 209 210 211 212 213 214 215 216 217 218 219 220 221 222 223
224 225 226 227 228 229 230 231 232 233 234 235 236 237 238 239
240 241 242 243 244 245 246 247 248 249 250 251 252 253 254 255
0
1
Example: If decimal number is “53”, the higher digit 1 of hexadecimal number is “3” and the lower digit 2 is “5”, and thus “35” is the hexadecimal number to be obtained.
0
2
– 19 –
2. MAC Address Setting Method1) Select the item number “7-01-01”.2) Press u key to activate the MAC Address Set mode.
(When the MAC Address Set mode becomes active, the MACaddress is displayed as shown in Fig.7-1-24)
Fig.7-1-24
3) Operating the keys on the set, set the MAC address.Note: Set the address values at three places on the right side.
Three address values on the left side are fixed valuesand not changeable.
• Key operation> or u key ...... Moves the cursor to the right.. key ................. Moves the cursor to the left.e key ..................... Increases address value at the cursor position.E key ..................... Decreases address value at the cursor position.x key ...................... Releases the MAC Address Set mode.y key .................... Writes MAC address.
4) Press y key to write the MAC address.Note: Even if the y key is pressed, the screen does not
change. Unless this key is pressed, the set MAC addressis not stored in nonvolatile memory.Also, the MAC address writing can be done only onceafter the power was turned on. To set the MAC addressonce more, the power must be turned off, and on again.
TEST MODE
Other
made by MD dep.
ITRON Ver. s. sssDrive Ver. s. sssJAVA APP Ver. ssssssssJAVA OS Ver. ssssssssBOOT Ver. s. sss IPL Ver. s. sssRATE CTL Ver. s. sss
Item No.
MAC Address Write
7–01–01
Adjust
MAC 08 : 00 : 46 : ss : ss : ss
MAC 08 : 00 : 46 : ss : ss : ss
Moves the cursor by > or u key
Moves the cursor by . key
– 20 –
1-6. Touch Panel Adjustment1. Touch Panel Position AlignmentThe touch panel position alignment should be made in both caseswhere the LCD screen is opened, and it is closed.In touching the screen, use the input pen attached.
Adjusting method1) Select the item number “7-01-02”.2) Press u key to activate the Touch Panel Position Alignment
mode.(The screen display will be as shown in Fig.7-1-25)
3) Touch the center of mark displayed at the upper left of LCDscreen.(The screen display switches to the one shown in Fig.7-1-26)
4) Touch the center of mark displayed at the lower right of LCDscreen.(The screen display switches to the one shown in Fig.7-1-27)
5) Touch the center of mark displayed in the center of LCD screen.6) The touch panel position alignment finishes, and the adjust-
ment result is displayed.• If alignment is successful ........... “OK!”• If alignment failed ...................... “NG!”
7) If the touch panel alignment is to be made once more by chang-ing the direction of the LCD, press u key to display the screenshown in Fig.7-1-25, and then perform adjustment after step3).Note: If the alignment failed, perform the touch panel posi-
tion alignment again without changing the LCD direc-tion.
8) At successful completion of the alignment in both cases wherethe LCD is opened and closed, press x key to release the TouchPanel Position Alignment mode.
2. Touch Panel Simple Check
Checking method1) Select the item number “7-01-03”.2) Check that “OK” is displayed when you touch the LCD screen.
Fig.7-1-25
Fig.7-1-26
Fig.7-1-27
Fig.7-1-28
Touch PanelPlease Touch
Touch PanelPlease Touch
Touch PanelPlease Touch
Touch Panel
NG!
Please Touch
Touch Panel
OK!
Please Touch
• In case of NG adjustment
• In case of successful adjustment
– 21 –
1-7. Other Checking1. Switch CheckIn the Switch Check mode, even pressing the x key cannot re-lease the Switch Check mode. To exit from this mode, turn thepower off.
Checking method1) Select the item number “7-02-01”.2) Press u key to activate the Switch Check mode.
(The screen display becomes as shown in Fig.7-1-29, and thedetection status of each switch on the set, LCD switch, andmecha. deck switch is displayed)
Fig.7-1-29
3) Check that each switch is detected normally.(See Table below. For the mecha. deck switch, see “Mecha.Deck Block Simple Check”)
• SET switch
Display Condition
COVER OPEN Disc lid is OPEN
CLOSE Disc lid is CLOSE
EJCT SW ON DISC EJECT switch ON
OFF DISC EJECT switch OFF
• LCD switch
Display LCD panel Condition
LCD NORMAL/CLOSE NORMAL/CLOSE
NORMAL/OPEN NORMAL/OPEN
REVERS/CLOSE REVERSE/CLOSE
REVERS/OPEN REVERSE/OPEN
• MECHANISM DECK switch
Display Remark
IN LIMIT SW Condition of OPTICAL PIC-UP in limitswitch
INITIAL SW Condition of REC HEAD initial positiondetect switch
MD1/MD2 Condition of MD1/MD2 detect switch
PIT/GRV Condition of REFLECT switch
PROTECT Condition of PROTECT detect switch
SW CHECK MODE
REVERSE/CLOSE
COVER CLOSEOFFEJECT SW
IN LIMIT SW INITIAL SWMD1/MD2PIT/GRVPROTECT SW
OFFOFFMD2GRVON
LCD
Mecha. deck switch status display
LCD switch status display
Set switch status display
2.Key CheckIn the Key Check mode, even pressing the x key cannot releasethe Key Check mode. To exit from this mode, turn the power off.
Checking method1) Select the item number “7-02-01”.2) Press u key to activate the Switch Check mode.3) From the Switch Check mode, press u key to activate the
Key Check mode. (The screen display becomes as shown inFig.7-1-30)
Fig.7-1-30
4) Check that the POWER switch detection status displayed atpart A is normal. (See Table below)
Display Condition
PLAY/EDIT MODE PLAY/EDIT position
MODE OFF OFF position
Camera MODE CAMERA position
Interview MODE INTERVIEW position
5) Check that a numeric value displayed at part B decreases ifthe control dial is rotated clockwise, or increases if counter-clockwise.
KEY CHECK MODE
ssssss
000
PLAY/EDIT MODE
A Power switch status display
C control dial status display
B Set key status display
– 22 –
6) Check that the name associated with the pressed key is dis-played at part C if a key on the set is pressed. (See Tablebelow)
Display Key name
PLAY u (PLAY/PAUSE)
STOP x (STOP)
FF > (FF)
REW . (REW)
SLOW y (SLOW)
A REC AUDIO REC
V REC (VIDEO REC)
PON ENTER
ERASE ERASE
MENU MENU
BRIGHT EXPOSURE
DISPLAY DSPL
VOLUME + e (VOL +)
VOLUME – E (VOL –)
PHOTO PHOTO
MARK BACK LIGHT
FORCUS FORCUS
7) Check that the “KEY CHECK MODE” characters on the screenchange to green in color if all keys on the set are pressed.
3. Adjustment Condition CheckIn the Adjustment Condition Check mode, current conditions ofservo auto adjustment, MAC address setting, and touch panel po-sition alignment canbe checked.
1) Select the item number “7-02-05”.2) Press u key to activate the Adjustment Condition Check
mode.(When the Adjustment Condition Check mode becomes ac-tive, the screen changes as shown in Fig.7-1-31, and currentadjustment conditions are displayed)
Fig.7-1-31
• escription of displayOK ........... Adjustment successfully completedNG ........... Adjustment failed (or not adjusted yet)– ............... Not adjusted yet (Servo auto adjustment only)
• Key operationx key ....... Releases the Adjustment Condition Check modey key ..... Initializes the Adjustment Condition Check mode
If y key is pressed, the condition display of servo auto adjust-ment will be all “–”, and that of MAC address setting and touchpanel position alignment will be “NG”. (Fig.7-1-31)Note: The adjustment data are not initialized even if the Adjust-
ment Condition Check mode is initialized.
4. Set Value InitializingEach set value on the set can be initialized to the factory setting.
Initializing method1) Select the item number “7-02-06”.2) Press y key, and “OK” will be displayed on the screen and
each set value will be initialized to the factory setting.
Adjust Condition
OK
NG
MD1 -- OKMO CD
Correct a location of Touch Panel
Write MAC address
MD2 OK NG
Condition display of servo auto adjustment
Condition display of MAC address setting
Condition display of touch panel position alignment
– 23 –
7-2. Firmware Data Writing Method
Write the data by the method given below, when the Main boardor the Flash Memory (IC8005) and MPEG Control (IC8501)mounted on the MAIN board were replaced.
2-1. Preparation1. Measuring EquipmentTo write the data, use measuring equipment listed below:1) Personal computer (Windows95/98 installed)2) Hyper Terminal (Communication software attached to the Win-
dows)3) Firmware Writer Ether Flash BB(U)
Part code: J-2503-019-A4) MPEG RATE CONTROL
Part code: J-2503-020-s5) RS-232C Cable D-Sub 9pin (Female) (Cross cable type)6) Regulated power supply7) AC Adaptor/Charger (AC-VQ800)
2. Connection1) Disconnect the CN8801 of ETHER board from the CN8007
of MAIN board, and connect the Ether Flash BB instead.Note: Be careful of the connection direction when connecting
the Ether Flash BB.2) Connect the CN7 of Ether Flash BB and the personal com-
puter with the RS-232C Cable (Cross cable type).
Fig.7-2-1
*1 Regulated power supply (15 Vdc)
TP5002 GND
TP8047 TEST
Test pins
MAIN BOARDPOWER BOARD
Cabinet (R)
AC adaptor/charger(AC-VQ800)
Ether Flash BB
RS-232C Cable (Cross cable Type)
2 1
CN3
CN6 CN7
*1 Use the regulated power supply and MPEG RATE CONTROL when MPEG Control (IC8501) was replaced.
CN8007
Personal computer
to RS-232C
*1 MPEG RATE CONTROL
– 24 –
3. Hyper Terminal Setting1) Double-click [Hypertrm.exe] in the Hyper Terminal folder of
the personal computer.2) On the [Connection Description] screen, enter the name “DCM-
M1” and select the icon, and then click [OK].
Fig.7-2-2
Select [Direct to Com1] for the Connect using: and click [OK].If Com1 port has been used, select [Direct to Com2].
Fig.7-2-3
3) On the [Port Settings] screen, set the following and click [OK].Bits per second: 57600Data bits: 8Parity: NoneStop bit: 1Flow control: Xon/Xoff
Fig.7-2-4
4) From the File on the menu bar, click the Properties to selectthe Settings screen.Next, click [ASCII Setup] on the Settings screen.
Fig.7-2-5
– 25 –
5) On the [ASCII Setup] screen, set the following and click [OK].[ASCII Sending]
Line delay: [2] milliseconds[ASCII Receiving]
[Append line feeds to incoming line ends]: [√] marking[Wrap lines that exceed terminal width]: [√] marking
Next, on the [Settings] screen, click [OK] once more.
Fig.7-2-6
4. Setting of the SetAfter the Hyper Terminal setting finished, check that the promptappears on the screen, and then perform a setting to the set throughthe steps given below.
1) Set the POWER switch to PLAY/EDIT.Note: Setting the POWER switch to CAMERA/INTERVIEW al-
lows the Auto Power OFF function to operate, thus caus-ing the power to be turned off during measurement. There-fore, be sure to set it to PLAY/EDIT.
2) Short the test pins TP8047 (TEST) and TP5002 (GND) withtweezers, etc.
3) From the AC Adaptor, turn the power on.4) Remove tweezers to release the test pins.5) Check that the following message is displayed on the screen.
Board Check Monitor ver1.XXX
5. Exit Hyper TerminalFrom the File on the menu bar, click the “Exit Hyper Terminal”.On the following screen, click [Yes] to finish the Hyper Terminal.
Fig.7-2-7
– 26 –
2-2. Writing to Flash Memory (IC8005)
Note 1: When the writing to the Flash Memory (IC8005) wasexecuted, perform the following:• MAC Address Setting (See Test Mode page 16)• Touch Panel Adjustment (See Test Mode page 20)
Note 2: Hyper Terminal setting must already be finished.Note 3: on typical screen display indicates input characters.
1) Perform a setting to the set. (See page 25)2) Make “Board Check Monitor ver1.XXX” displayed on the
screen, enter “WT” for the prompt and press the [Enter] key.3) Data writing to the Flash Memory starts, and the progress sta-
tus is displayed on the screen as shown below. After about oneminute, [WT>OK] is displayed and the writing finishes.
Board Check Monitor ver1.XXX> WTFormatting FLASH file... src=1 ,dst=0Format done.Copying file: MDCX_ITRON@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@Copying file: MDCX_JAPP@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@Copying file: MDCX_JAVA@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@Copying file: MDCX_FTPBT@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@Copying file: MDCX_FTPD@@@@@@@@Copying file: MDCX_WKSCR@@@@@Copying file: MDCX_JDICS@@@@@@@@@@@@@@@@Copying file: MDCX_EFFECT@Copying file: MDCX_SLEEP@Copying file: MDCX_VERSION@Copying 2nd partition...End of WT.WT>OK
Fig.7-2-8 Typical screen display
4) Exit the Hyper Terminal. (See page 25)
2-3. Writing to MPEG Control (IC8501)
Note 1: Hyper Terminal setting must already be finished.Note 2: on typical screen display indicates input characters.
1) Insert MPEG RATE CONTROL disc into the drive A.2) Perform a setting to the set. (See page 25)3) Apply +15Vdc to the CN6 of Ether Flash BB.4) Make “Board Check Monitor ver1.XXX” displayed on the
screen, enter “V” for the prompt and press the [Enter] key.5) After [V850E>] is displayed, enter “R” and press the [Enter]
key.6) Again, after [V850E>] is displayed, enter “L” and press the
[Enter] key.7) From the Transfer on the menu bar, click [Send Text File] to
display the [Send Text File] screen.
Fig. 7-2-9
Select [3 1/2 Floppy (A:)] for the Look in, and [All files (*.*)]for the File type.Click the “Rom_1000.hex” displayed on the screen to high-light, and click [Open].The data are then sent and displayed on the screen.
8) After [V850E>] is displayed, enter “A” and press the [Enter]key.The Flash Data writing starts, and the following is displayed:[Program to V850 flash memory finished] Then, [V850E>] isdisplayed as a prompt.
9) Enter “Q” to quit the data writing.10) Exit the Hyper Terminal. (See page 25)Note 3: Disconnect the +15Vdc applied to the CN6 of Ether Flash
BB in prior to disconnection of the power supply fromthe AC Adaptor.
– 27 –
Board Check Monitor ver1.XXX> V << V850E Flash Writer menu V0.203 >> A ........................... V850E Auto sequence
(Erase, Program,Verify) R ........................... V850E Device reset P ........................... V850E Program mode on I ............................ Initialize parameter L ........................... Load Motlora S format file W .......................... Write all flash memory E ........................... Erase all flash memory (without PreWrite) C<CMD [prm]> ... Send V850E command Q ........................... Quit V850 menuV850E> RV850E RESET,Vpp=7.8VV850E> LS0086262322E6F75747BS2080000008007C00AA6S254000130E00F40005C1A630F0100E10F40005C1A630F0100E087600180FF684BC0FF58F1D20DC0BF58F1243779860656010064577986005FDAF0465F0000E0076001230F0100441AE10F2000230F0100441AE107FF
~ an omission ~
S21500DB5C0000000000000000000000000000000000B3S804000AC031V850E> AV850E RESET,Vpp=7.8VV850E PROGRAM MODE .... FAILEDV850E PROGRAM MODE .... READYFREQ SET COMMAND OKERASE SET COMMAND OKWRITE SET COMMAND OKBAUDRATE SET COMMAND baudrate 76800bps OKWRITEBACK SET COMMAND OKInitialize OK!WRITE ALL 0.............................................. OKALL ERASE Waiting ... OKRESET COMMAND OKALL BLANK CHECK Waiting ... OKWRITE START.............................................. OKALL VERIFY.............................................. OK Program to V850 flash memory finished.V850E RESET,Vpp=7.8VV850E> Q>
Fig.7-2-10 Typical screen display
– 28 –
• Correction of Schematic Diagrams! : Indicates changed portion.MAIN BOARD (1/8) (Page 4-29 to 4-30. Location A to E, 1 to 8)
Incorrect
Correct
$
#
#
#
%
!
$
#
#
#
%
!
– 29 –
MAIN BOARD (3/8) (Page 4-32. Location E, 28)
Incorrect Correct
MAIN BOARD (3/8) (Page 4-32. Location J, 27 to 29)
Incorrect Correct
MAIN BOARD (3/8) (Page 4-39. Location C to E, 1 to 4)
Incorrect Correct
MAIN BOARD (3/8) (Page 4-39 to 40. Location E, 8 to 10)
Incorrect Correct
MAIN BOARD (3/8) (Page 4-40. Location C to E, 11 to 14)
Incorrect Correct
$
^
^
^^
^
$
# $
^
^
%
%
$
^
^
^^
^
$
# $
^
^
%
%
– 30 –
MAIN BOARD (3/8) (Page 4-40. Location C, 15 to 19)
Incorrect Correct
$
MAIN BOARD (3/8) (Page 4-40. Location F to G, 17 to 18)
Incorrect Correct
%
MAIN BOARD (3/8) (Page 4-40. Location J to L, 15 to 18)
Incorrect Correct
$
MAIN BOARD (4/8) (Page 4-44. Location A to B, 14 to 17)
Incorrect Correct
%
@
$##
$
%
^
^
$$#
#
– 31 –
MAIN BOARD (4/8) (Page 4-44. Location D to E, 14 to 16)
Incorrect Correct
MAIN BOARD (4/8) (Page 4-44 to 45. Location J to L, 17 to 19)
Incorrect Correct
MAIN BOARD (4/8) (Page 4-45. Location H to J, 24 to 27)
Incorrect Correct
MAIN BOARD (4/8) (Page 4-46. Location G to H, 30 to 33)
Incorrect Correct
%
%
^
%
#
%
%
#
%
#
– 32 –
MAIN BOARD (5/8) (Page 4-48. Location F to G, 1 to 4)
Incorrect Correct
MAIN BOARD (8/8) (Page 4-59. Location L, 1 to 4)
Incorrect Correct
CLV BOARD (Page 4-77. Location G to H, 12 to 14)
Incorrect Correct
REC BOARD (Page 4-82. Location D to E, 10 to 12)
Incorrect Correct
#
#
#
%
#
#
#
#
%
#
DCM-M1
– 33 – – 34 – – 35 –LCDLCD
• Signal Paths were Missing in Service Manual.LCD (LCD) SCHEMATIC DIAGRAM (Page 4-106 to 4-108)
– 38 –
Sony CorporationAudio Entertainment Group9-927-635-82
2000E05035-1Printed in Japan C 2000. 5
Published by PE General Engineering Dept.
ETHER BOARD (Page 4-116. Location D, 1 to 3)
Incorrect Correct
#
DCM-M1
#
SERVICE MANUAL2000. 08
DCM-M1
SUPPLEMENT-3File this supplement with the service manual.
Subject:• Addition of Section 7 Camera Section Adjustment• Correction of Schematic Diagrams
US ModelCanadian Model
E Model
– 2 –
7-3. CAMERA SECTION ADJUSTMENT
TABLE OF CONTENTS
3-1. Preparation before Adjustment .................................. 33-1-1. Service Tools List ........................................................ 33-1-2. Preparation .................................................................. 43-1-3. Precautions ................................................................. 5
3-2. Operation during Adjustment ........................................ 63-2-1. How to Enter the Test Mode ........................................ 63-2-2. How to Exit from the Test Mode .................................. 63-2-3. Description of Test Mode Screen ................................ 63-2-4. Key Operation in Test Mode ........................................ 7
3-3. Camera System Adjustment ........................................ 81. Zoom Center Adjustment ................................................ 82. Hall Adjustment ............................................................... 83. Flange Back Adjustment (Using flange back
adjusting chart subject more than 500 m away) ............. 94. Flange Back Adjustment (Using mini pattern box) ......... 115. Flange Back Check ......................................................... 126. Optical Axis Adjustment .................................................. 137. AGC Gain Calibration Adjustment .................................. 158. Color Reproduction Adjustment ...................................... 169. Max. Gain Adjustment ..................................................... 1710. Auto White Balance & LV Reference Data Acquisition ... 1811. Auto White Balance Adjustment ..................................... 1812. Auto White Balance Check .............................................. 19
• Main PartsThe following parts can be supplied as main parts of the camera block in this set.1) Camera Block (General Assembly including 2), 3) mentioned below and minor parts) .... (A-3250-920-A)2) Zoom Lens (LSV-620B) ....................................................................................................... (8-848-732-01)3) CCD Block Assembly ........................................................................................................... (A-3328-667-A)
* Further, there are small parts such as brackets and screws. See the Parts Price List.* The Camera Process Board (VC-216 Board) alone is not supplied.
• Adjustment Items Required When Main Parts are ReplacedWhen the main parts were replaced, the adjustments marked with “z” in the following table are required.
Replacement Parts Camera Block Zoom Lens (LSV-620B) CCD Block Ass’y
Camera Block (A-3250-920-A) (8-848-732-01) (A-3328-667-A)
Zoom Center Adjustment (Note 1) z
Hall Adjustment z
Flange Back Adjustment z z (Note 2)
Optical Axis Adjustment z z
AGC Gain Calibration Adjustment z
Color Reproduction Adjustment z
Max Gain Adjustment z
Auto White Balance &z
LV Reference Data Acquisition
Auto White Balance Adjustment z
Table 7-3-1
Note 1: Also, if the Zoom Switch Unit (1-418-202-21) was replaced, perform the Zoom Center Adjustment.Note 2: Check the flange back, and if deviated, adjust it.
– 3 –
3-1. Preparation before Adjustment
3-1-1. Service Tools List• Oscilloscope • Color Monitor • Vectorscope• Regulated Power Supply • Digital Voltmeter
Ref. No. Name Part Code Usage
J-1 Filter for color temperature correction (C14) J-6080-058-AAuto white balance adj./checkWhite balance adj./check
J-2ND filter 1.0 J-6080-808-A White balance check
ND filter 0.3 J-6080-818-A White balance check
J-3 Pattern box PTB-450 J-6082-200-A
J-4 Color chart for pattern box J-6020-250-A
J-5 Siemens star chart J-6080-875-A Flange back check
J-6 Clear chart for pattern box J-6080-621-A
J-7 Mini pattern box J-6082-353-B Flange back adjustment
J-8 Camera base J-6082-384-A Flange back adjustment
J-1 J-2 J-3 J-4 J-5
J-6 J-7 J-8
Fig. 7-3-1
– 4 –
3-1-2. Preparation
Note 1: See “DISASSEMBLY” for removing the cabinet and eachboard.
Note 2: The lens block and each board need not be separated, ifonly the adjustment is performed.
Note 3: For the power supply, use exclusive AC adapter.
Fig. 7-3-2
Pattern box
Front side of the lens
about 1.5m
– 5 –
3-1-3. Precautions
1. Switch settingSet the switches to the following positions respectively and per-form the adjustment without loading a disc, unless otherwise speci-fied.
1. POWER switch ...................................................... CAMERA2. DIGITAL ZOOM (MENU screen) ........................ OFF3. STEADY SHOT (MENU screen) ......................... OFF4. FOCUS ................................................................... MANUAL5. PROGRAM AE (MENU screen) ........................... AUTO6. PICTURE EFFECT (MENU screen) .................... OFF7. WHITE BALANCE (MENU screen) .................... AUTO8. AUTO SHUTTER (MENU screen) ...................... OFF
H
A=B
C=D
A B B
C D
A
Enlargement
V
Electronic beam scanning frame
CRT picture frame
B A
Difference in level
Yello
wC
yan
Gre
enW
hite
Mag
enta
Red
Blu
e
Yello
wC
yan
Gre
enW
hite
Mag
enta
Red
Blu
e
Color bar chart (Color reproduction adjustment frame)
Fig. a(VIDEO terminal of A/V jackoutput waveform)
Fig. b (monitor TV picture)
Adjust the camera zoom and direction toobtain the output waveform shown in Fig. aand the monitor TV display shown in Fig. b.
2. Order of AdjustmentsBasically carry out adjustments in the order given.
Fig. 7-3-3
3. Subjects1) Color bar chart (Color reproduction adjustment frame)
When performing adjustments using the color bar chart, adjustthe picture frame as shown in Fig. 7-3-3. (Color reproductionadjustment frame)
2) Clear chart (Color reproduction adjustment frame)Remove the color bar chart from the pattern box and insert aclear chart in its place. (Do not perform zoom operations duringthis time)
3) Chart for flange back adjustmentJoin together a piece of white A0 size paper (1189 mm × 841mm) and a piece of black paper to make the chart shown inFig. 7-3-4.
Note: Use a non-reflecting and non-glazing vellum paper. Thesize must be A0 or larger and the joint between the whiteand black paper must not have any undulations.
Black
White841 mm
1189 mm
Fig. 7-3-4
– 6 –
3-2. Operation during Adjustment
In adjusting the camera, execute the service mode in the Test Mode.Note: For the adjustment items that must be checked with the color
monitor, first connect the VIDEO OUT to the monitor, andthen set the Test Mode.(If connected later, no video signal will be outputted.)
3-2-1. How to Enter the Test ModeIn the normal mode, set the POWER switch to “CAMERA”.While pressing u key on the set, press >, >, ., .,e, E, e, E, y, y keys on the set in this order.The Test Mode screen (Fig. 7-3-5) appears on the LCD and theTest mode becomes active.
Fig. 7-3-5
3-2-2. How to Exit from the Test ModeTurn the power off.Note: In the Test mode, the POWER switch is inactive and there-
fore disconnect AC adapter to turn the power off.
3-2-3. Description of Test Mode Screen
Fig. 7-3-6
TEST MODE
Camera
made by MD dep.
I TRON Ver. s. sssDrive Ver. s. sssJAVA APP Ver. ssssssssJAVA OS Ver. ssssssssBOOT Ver. s. sss I PL Ver. s. sssRATE CTL Ver. s. sss
Item No. 1–00–00
TEST MODE
Camera
made by MD dep.
I TRON Ver. s. sssDrive Ver. s. sssJAVA APP Ver. ssssssssJAVA OS Ver. ssssssssBOOT Ver. s. sss I PL Ver. s. sssRATE CTL Ver. s. sss
Item No.
Service mode
1–02–01
06–00–00
Ad jus t
Camera register display field
Test mode item name display fieldTest mode item No.
display fieldVersion display field
1) Version display fieldThe versions of respective programs that compose the set aredisplayed.ITON ............ Version of set programDrive ............. Version of drive programJAVA APP ..... Version of JAVA applicationJAVA OS ....... Date when JAVA OS was releasedBOOT ........... Version of BOOT programIPL ................ Version of IPL programRATE CTL ... Version of V850 (IC8501 on Main board)
program
2) Test mode item number display field
Fig. 7-3-7
Current Test mode item number is used.The Test mode items are composed of a major item, mediumitem, and minor item.The number displayed in blue is currently active item.
3) Test mode item name display field
Fig. 7-3-8
Major item name, medium item name, and minor item name ofcurrent test mode are displayed respectively.
4) Camera register display field
Fig. 7-3-9
The register state (page/address/data) in the camera block is dis-played. Also, active item at present is underlined with a red cur-sor.
Item No. 1–02–01
Major item number
Minor item numberMedium item number
CameraService mode
Ad jus t
Major item name Medium item name
Minor item name
06–00–00
Page
Address
Data
Cursor
– 7 –
3-2-4. Key Operation in Test ModeIn the Test mode, use the keys on the set for operation.For adjusting the camera, execute the test mode item “1-02-01”(major item: Camera, medium item: Adjust, and minor item: Ser-vice mode) to select the Service mode and perform adjustmentwhile writing data to the camera register.
1. Change or setting of test mode item• Movement over active item numbers (u, x keys)
Fig. 7-3-10
Use u key when setting active item number and movingto lower level, or use x key when canceling current itemand moving to higher level.
• Change of active item number (> . keys)Use > key to raise active item number, or . key tolower it.
• Execution or cancellation of item (u, x keys)If the test mode item “1-02-01” (major item: Camera, me-dium item: Adjust, and minor item: Service mode) was set,pressing the u key causes the register state to be displayedin the cameral register display field, and the Service modeto be active. To cancel this item, press the x key.
Item No. 1–02–01
x key Moveing
u key Moveing
2. Change or writing of camera register(Operation in Service mode)• Cursor movement (., > keys)
Fig. 7-3-11
Pressing the . key or > key causes the cursor to bemoved as shown above.Note: If page is “01”, the cursor will stand still at the page
position.
• Page change (e, E keys)When the cursor is in page position, pressing the e key in-creases the page, or the E key decreases the page. There are15 pages, 01 to 0F.
• Address change (e, E keys)When the cursor is in address position, pressing the e keyincreases the address, or the E key decreases the address.Also, pressing the u key increases the higher order digitof 00-FF.There are 256 addresses, 00 to FF.
• Data change (e, E keys)When the cursor is in data position, pressing the e key in-creases the data, or the E key decreases the data.Also, pressing the u key increases the higher order digitof 00-FF.There are 256 data, 00 to FF.
• Data writing (y key)To write data to the nonvolatile memory, press the y key.(Unless this operation is performed, new data are not storedin the nonvolatile memory.)
3. Switching of screen displayThe camera adjustment contains the items to be adjusted with thecamera-through screen.
• Camera-through screen display method (DSPL key)Press the DSPL key, and the screen display will be switchedas shown below.
06–00–00
Moves the cursor by . key
Moves the cursor by > key
Test mode screen
10-step gradation pattern screen
(Camera-through screen, if not set in “EVF” item)
Camera-through screen
– 8 –
3-3. Camera System Adjustment
1. Zoom Center AdjustmentAdjust the center voltage of Zoom control to the center of microcomputer A/D value.If deviated, zooming will be executed even with the Zoom control in center position.
Adjusting method
Steps Page Address Data Work Description
1 06 50 Read the displayed data (D50).
2 0F 5D D50 Set the data read in step 1, and press the y key.
2. Hall AdjustmentTo detect the lens iris position, adjust the gain and offset of the amplifier.If deviated, the iris will oscillate or the white balance between indoor and outdoor will be disordered.
Note: For the data display, the data at the time when address was set is displayed, and it is not updated.Check data variation while repeating address change and resetting (change address from “02” to “01”, and then return it to “02”).
Adjusting method
Steps Page Address Data Work Description
1 06 02 Check that the data is “00”.
2 06 94 8A Press the y key.
3 06 95 17 Press the y key.
4 06 01 6DPress the y key.(Hall is adjusted, and the data are automatically entered to page: F, address: 1E, 1F, 70.)
5 06 02 Check that the data becomes “01”. (Note)
6 06 01 00 Press the y key.
Processing after completion of adjustment
Steps Page Address Data Work Description
1 06 01 00 Press the y key.
2 06 94 00 Press the y key.
3 06 95 00 Press the y key.
Subject Arbitrary
Measurement point Display data of page: 06, address: 50
Adjustment page 0F
Adjustment address 5D
Note: Do not touch the Zoom lever during adjustment.(The Zoom lever must be in center position.)
Subject Arbitrary
Adjustment page 0F
Adjustment address 1E, 1F, 70
– 9 –
3. Flange Back Adjustment (Using flange back adjusting chart subject more than 500 m away)The flange back adjustment of the inner focus lens is carried out automatically.If deviated, auto focus and manual focus will be disordered.
Flange back adjustment (1)
Note: For the data display, the data at the time when address was set is displayed, and it is not updated.Check data variation while repeating address change and resetting (change address from “02” to “01”, and then return it to “02”).
Adjusting method
Steps Page Address Data Work Description
1With the zoom lens at TELE end and WIDE end respectively, check that the center of theshot image screen concurs with the center of flange back adjusting chart.
2 06 02 Check that the data is “00”.
3 06 01 13 Press the y key.
4 06 01 15Press the y key.(The flange back adjustment is carried out, and the data are automatically entered topage: F, address: 24 – 29 and 36 – 3D.)
5 06 02 Check that the data becomes “01”. (Note)
Processing after completion of adjustment
Steps Page Address Data Work Description
1 06 01 00 Press the y key.
2 Perform “Flange back adjustment (2)”.
SubjectFlange back adjusting chart(Located at 2.00 m position from lens front surface)(Luminance: 350 (50 lux)
Measurement point Check operation on monitor TV
Measuring instrument (Camera-through screen)
Adjustment page 0F
Adjustment address 24 – 29, 36 – 3D
– 10 –
Flange back adjustment (2)
Note: For the data display, the data at the time when address was set is displayed, and it is not updated.Check data variation while repeating address change and resetting (change address from “02” to “01”, and then return it to “02”).
Adjusting method
Steps Page Address Data Work Description
1With the zoom lens at TELE end, shoot the subject distant over 500 m (such as a buildinghaving clear contrast).(At this time, the subjects distant below 500 m must not be displayed on the screen.)
2 06 02 Check that the data is “00”.
3 06 01 13 Press the y key.
4 Cover the lens with ND filter, and adjust so as to get the optimum image.
5 06 01 29Press the y key.(The flange back adjustment is carried out, and the data are automatically entered topage: F, address: 24 – 29 and 36 – 3D.)
6 06 02 Check that the data becomes “01”. (Note)
Processing after completion of adjustment
Steps Page Address Data Work Description
1 06 01 00 Press the y key.
2 Perform “Flange Back Check”.
SubjectSubject more than 500 m away(which should be clear contrast such as a building)
Measurement point Check operation on monitor TV
Measuring instrument (Camera-through screen)
Adjustment page 0F
Adjustment address 24 – 29, 36 – 3D
– 11 –
4. Flange Back Adjustment (Using mini pattern box)The flange back adjustment of the inner focus lens is carried out automatically.If deviated, auto focus and manual focus will be disordered.
Note 1: Darker Siemens star chartNote 2: The mini pattern box is used for the flange back adjustment only.
For other adjustments, use the pattern box (PTB-450).Note 3: For the data display, the data at the time when address was set is displayed, and it is not updated.
Check data variation while repeating address change and resetting (change address from “02” to “01”, and then return it to “02”).
Preparation for adjustmentInstall the mini pattern box as shown below.Note 4: The attachment is not used.
Adjusting method
Steps Page Address Data Work Description
1 Install the mini pattern box so that it is located within 3 cm from the lens front surface.
2 Adjust the height of mini pattern box.
3Check that the output voltage of regulated power supply is the specified voltage± 0.01 Vdc.
4With the zoom lens at TELE end and WIDE end respectively, check that the center of theshot image screen concurs with the center of Siemens star frame.
5 06 02 Check that the data is “00”.
6 06 01 13 Press the y key.
7 06 01 27Press the y key.(The flange back adjustment is carried out, and the data are automatically entered topage: F, address: 24 – 29 and 36 – 3D.)
8 06 02 Check that the data becomes “01”. (Note 3)
Processing after completion of adjustment
Steps Page Address Data Work Description
1 06 01 00 Press the y key.
2 Perform “Flange Back Check”.
SubjectMini pattern box with ND filterSiemens star chart (Note 1)
Measurement point Check operation on monitor TV
Measuring instrument (Camera-through screen)
Adjustment page 0F
Adjustment address 24 – 29, 36 – 3D
Mini pattern box
Within 3 cm
Set
Camera base
Red (+)
Black (–)
Yellow (SENS +)
White (SENS –)
Black (GND)
No connection
Regulated power supplySpecified voltage ( 0.01 Vdc)
Output current over 3.5 A
Fig. 7-3-12
Specified voltage: Variable depending on the mini pattern box.Therefore, set the voltage given on the sheetattached to the mini pattern box.
– 12 –
5. Flange Back Check
Switch setting1) DIGITAL ZOOM (Menu screen) ....... OFF2) STEADY SHOT (Menu screen) ......... OFF3) FOCUS ................................................ AUTO
Note: When Auto Focus is ON, whether the focus is in order or disordered can be judged from the data displayed on page 01.1) Select page: 06, address: 04, and set data: 0F, then press the y key.2) The focusing condition can be confirmed from the data displayed on page 01.
01-00-XXOdd number : Focus is in order.Even number: Focus is disordered.
Checking method
Steps Page Address Data Work Description
1Place the Siemens star at 2.0 m forward position from the lens front surface. As the iris isin open state, lower the luminance of Siemens star to the extent that noise does not appearon the monitor TV.
2 Shoot the Siemens star with the zoom at TELE end.
3 Check that the focus is in order. (Note)
4 06 21 10 Press the y key.
5 Shoot the Siemens star with the zoom at WIDE end.
6 Check on the monitor screen that the focus is in order.
Processing after completion of check
Steps Page Address Data Work Description
1 06 21 00 Press the y key.
2 06 04 00 Press the y key.
SubjectSiemens star (reflection type)(Located at 2.00 m position from lens front surface)(Luminance: about 200 lux)
Measurement point Check on monitor TV
Measuring instrument (Camera-through screen)
Adjustment value Focus must be in order at TELE end and WIDE end
– 13 –
6. Optical Axis AdjustmentCorrect the deviation of optical axis between lens and CCD imager.If deviated, the center of screen will be shifted when the zoom is moved from TELE end to WIDE end.
Switch setting1) DIGITAL ZOOM (Menu screen) ....... OFF2) STEADY SHOT (Menu screen) ......... OFF
Preparation for adjustment:Stick the optical axis deviation specification frame to the monitor screen. At this time, make the monitor center and the specification framecenter concurrent.
Subject Siemens star (reflection type)
Measurement point Check on monitor TV
Measuring instrument (Camera-through screen)
Adjustment page 0F
Adjustment address 43
0
180
90
67.5
22.5337.5
292.5
247.5
202.5 157.5
112.5
8
4
5
7 1
6 2
3
270
Fig. 7-3-13
– 14 –
Adjusting method
Steps Page Address Data Work Description
1 06 40 02 Press the y key.
2 06 41 01 Press the y key.
3 0F 43 00 Press the y key.
4 Place the Siemens star at 2.0 m forward position from the lens front surface.
5 Shoot the Siemens star with the zoom at TELE end.
6Adjusting the lens direction, make the center of Siemens star and the center of optical axisdeviation specification frame (monitor screen) concurrent.
7 Shoot the Siemens star with the zoom at WIDE end.
8
On the monitor TV, check which area of the optical axis deviation specification frame thecenter of Siemens star enters.At this time, measure the center deviation “L1” (distance between center of Siemens starand center of optical axis deviation specification frame).
Read correction data (D43) according to the area in the following table.
9
10 0F 43 D43 Set the read correction data, and press the y key.
11 Shoot the Siemens star with the zoom at TELE end.
12Adjusting the lens direction, make the center of Siemens star and the center of optical axisdeviation specification frame concurrent.
13 Shoot the Siemens star with the zoom at WIDE end.
14Measure the center deviation “L2” (distance between center of Siemens star and center ofoptical axis deviation specification frame).
15 0F 43Compare L1 and L2 to make sure that L2 is smaller than L1.If larger, set data: 00 and press the y key.
Processing after completion of adjustment
Steps Page Address Data Work Description
1 06 40 00 Press the y key.
2 06 41 00 Press the y key.
Area Deviation phase Correction data
1 22.6° – 67.5° 01
2 67.6° – 112.5° 02
3 112.6° – 157.5° 03
4 157.6° – 202.5° 04
5 202.6° – 247.5° 05
6 247.6° – 292.5° 06
7 292.6° – 337.5° 07
8 337.6° – 22.5° 08
– 15 –
7. AGC Gain Calibration Adjustment
Note: For the data display, the data at the time when address was set is displayed, and it is not updated.Check data variation while repeating address change and resetting (change address from “02” to “01”, and then return it to “02”).
Switch setting1) DIGITAL ZOOM (Menu screen) ....... OFF2) STEADY SHOT (Menu screen) ......... OFF
Adjusting method
Steps Page Address Data Work Description
1 06 02 Check that the data is “00”.
2 0F 6E 08 Press the y key.
3 06 01 71Press the y key.(The AGC gain calibration adjustment is carried out, and the data are automaticallyentered to page: E, address: 3A – 3D.)
4 06 02 Check that the data becomes “01”. (Note)
Processing after completion of adjustment
Steps Page Address Data Work Description
1 0F 6E FF Press the y key.
2 06 01 00 Press the y key.
SubjectClear chart (PTB-450)(Color reproduction adjusting frame)
Adjustment page 0E
Adjustment address 3A – 3D
– 16 –
8 Color Reproduction AdjustmentAdjust the primary color separation matrix factor so that colors are reproduced correctly.If deviated, colors are not reproduced correctly.
Adjusting method
Steps Page Address Data Work Description
1 06 00 01 Press the y key.
2 06 01 3D Press the y key.
3 0F 16 37 Press the y key.
4Adjusting the GAIN and PHASE of the vectorscope, adjust the burst luminance point tothe burst position of the color reproduction adjusting frame.
5 0F 5E 29 Press the y key.
2E
6 0F30
44
45
Processing after completion of adjustment
Steps Page Address Data Work Description
1 0F 5E 2E Press the y key.
2 0F 16 33 Press the y key.
3 06 00 00 Press the y key.
4 06 01 00 Press the y key.
SubjectColor bar chart (PTB-450)(Color reproduction adjusting frame)
Measuring pointVIDEO terminal of VIDEO/AUDIO terminals(Camera-through screen)
Measuring instrument Vectorscope
Adjustment page 0F
Adjustment address 2E, 30, 44, 45
Adjustment valueAll color luminance points must fall in respectivecolor reproduction frame
Change the data so that each color luminance point falls within each color reproduciblearea.
Note: Each time the data is changed, press the y key.Unless this key is pressed, new data is not written.
R-Y
B-Y
R
B
G
MG
YE
CY
Burst position
Fig. 7-3-14
– 17 –
9. Max. Gain AdjustmentSet the lowest subject illuminance.If deviated, necessary video level will not be got in low illuminance environment.
Note: For the data display, the data at the time when address was set is displayed, and it is not updated.Check data variation while repeating address change and resetting (change address from “02” to “01”, and then return it to “02”).
Switch setting1) STEADY SHOT (Menu screen) ......... OFF
Adjusting method
Steps Page Address Data Work Description
1 06 02 Check that the data is “00”.
2 06 96 00 Press the y key.
3 06 97 27 Press the y key.
4 06 01 6FPress the y key.(The max. gain adjustment is carried out, and the data is automatically entered topage: F, address: 2C.)
5 06 02Check that the data becomes “01”. (Note)It may take much time (several sec to ten and several sec).
Processing after completion of adjustment
Steps Page Address Data Work Description
1 06 96 00 Press the y key.
2 06 97 00 Press the y key.
3 06 01 00 Press the y key.
SubjectClear chart (PTB-450)(Color reproduction adjusting frame)
Adjustment page 0F
Adjustment address 2C
– 18 –
10. Auto White Balance & LV Reference Data Acquisition
Note 1: Color Reproduction Adjustment must be already finished.Note 2: The auto white balance & LV reference data acquisition is available only once after the power is turned on. Turn the power off,
then on again if the data acquisition is retried.Note 3: For the data display, the data at the time when address was set is displayed, and it is not updated.
Check data variation while repeating address change and resetting (change address from “02” to “01”, and then return it to “02”).
Adjusting method
Steps Page Address Data Work Description
1 06 02 Check that the data is “00”.
2 06 01 11 Press the y key.
3 06 01 0DPress the y key.(The auto white balance & LV reference data acquisition is carried out, and the data areautomatically entered to page: F, address: 20 – 23, 3E, 3F.)
4 06 02 Check that the data becomes “01”. (Note 3)
Processing after completion of adjustment
Steps Page Address Data Work Description
1 06 01 00 Press the y key.
2 Perform “Auto White Balance Adjustment”.
11. Auto White Balance AdjustmentAdjust auto white balance so that correct data are outputted.If deviated, color reproduction in the auto white balance mode will be reduced.
Note 1: “Auto White Balance & LV Reference Data Acquisition” must be already finished.Note 2: The auto white balance adjustment is available only once after the power is turned on. Turn the power off, then on again if the
adjustment is retried.Note 3: For the data display, the data at the time when address was set is displayed, and it is not updated.
Check data variation while repeating address change and resetting (change address from “02” to “01”, and then return it to “02”).
Adjusting method
Steps Page Address Data Work Description
1 Cover the lens with the color temperature correction filter C14.
2 06 02 Check that the data is “00”.
3 06 01 83 Press the y key.
4 06 01 81Press the y key.(The auto white balance adjustment is carried out, and the data are automatically enteredto page: F, address: 34, 35.)
5 06 02 Check that the data becomes “01”. (Note 3)
Processing after completion of adjustment
Steps Page Address Data Work Description
1 06 01 00 Press the y key.
SubjectClear chart (PTB-450)(Color reproduction adjusting frame)
Adjustment page 0F
Adjustment address 20 – 23, 3E, 3F
Subject Clear chart (PTB-450)(Color reproduction adjusting frame)
Filter Color temperature correction filter C14
Measurement point Displayed data on page: 01
Adjustment page 0F
Adjustment address 34, 35
– 19 –
12. Auto White Balance Check
Checking method
Steps Page Address Data Work Description
1 Check that the lens is not covered with any filter.
2 06 01 0F Press the y key.
3 Check that the center of white luminance point is within a circle shown in Fig. 7-3-15 (A).
4 06 01 23 Press the y key.
5 Cover the lens with C14 filter.
6 Check that the center of white luminance point falls within a circle shown in Fig. 7-3-15 (B).
7 Remove the C14 filter, and cover the lens with ND filter 1.3 (1.0 + 0.3).
8After making sure that the white luminance point pull-in motion finished, remove the NDfilter 1.3.
9 Check that the center of white luminance point falls within a circle shown in Fig. 7-3-15 (C).
Processing after completion of check
Steps Page Address Data Work Description
1 06 01 00 Press the y key.
SubjectClear chart (PTB-450)(Color reproduction adjusting frame)
FilterColor temperature correction filter C14ND filter 1.0 and 0.3
Measurement pointVIDEO terminal of VIDEO/AUDIO terminals(Camera-through screen)
Measuring instrument Vectorscope
Adjustment value Fig. 7-3-15 (A) – (C)
Fig. 7-3-15 (A) Fig. 7-3-15 (B) Fig. 7-3-15 (C)
R-Y
B-Y
2 mm
2 mm
R-Y
B-Y
3 mm
3 mm
2 mm
1 mm
R-Y
B-Y
0.5 mm
1 mm
3 mm
3 mm
– 20 –
Incorrect Correct
• Correction of Schematic Diagrams! : Indicates changed portion.MAIN BOARD (4/8) (Page 4-44. Location B to C, 14 to 16)
^^
Incorrect Correct
MAIN BOARD (5/8) (Page 4-52. Location A to B, 37 to 39)
^ ^^^
Incorrect Correct
MAIN BOARD (6/8) (Page 4-53. Location A to E, 5 to 8)
#
%
#
%
– 21 –
Incorrect Correct
VF BOARD (2/3) (Page 4-90. Location I to J, 30 to 32)
Incorrect Correct
ETHER BOARD (Page 4-117. Location B to D, 6 to 9)
% ^ % ^
#
%
#%
– 22 –
FOR CAMERA OPTICAL AXIS ADJUSTMENT
0
180
90
67.5
22.5337.5
292.5
247.5
202.5 157.5
112.5
8
4
5
7 1
6 2
3
270
– 23 –
DCM-M1
FOR CAMERA COLOR REPRODUCTION ADJUSTMENT
Take a copy of CAMERA COLORREPRODUCTION FRAME with aclear sheet for use.
R-Y
B-Y
R
B
G
MG
YE
CY
Sony CorporationAudio Entertainment Group9-927-635-83 2000H05035-1
Printed in Japan C 2000. 8Published by General Engineering Dept.
CDM-M1
![Lawrie v Carey DCM and Anor [2016] NTSC 23 PARTIES](https://static.fdokumen.com/doc/165x107/632542fc051fac18490d2d4b/lawrie-v-carey-dcm-and-anor-2016-ntsc-23-parties.jpg)
