agra division-s and t/north central rly tender document

AGRA DIVISION-S AND T/NORTH CENTRAL RLY

TENDER DOCUMENT

Closing Date/Time: 08/03/2019 15:00 Tender No: AGRA-ST-2019-12

of 33 Run Date/Time: 07/02 /2019 14:45 :34

SrDSTE/Co acting for and on behalf of The President of India invites E-Tenders against Tender No AGRA-ST-2019-12 Closing

Date/Time 08/03/2019 15:00 Hrs. Bidders will be able to submit their original/revised bids upto closing date and time only. Manual offers

are not allowed against this tender, and any such manual offer received shall be ignored.

Contractors are allowed to make payments against this tender towards tender document cost and earnest money only through only

payment modes available on IREPS portal like net banking, debit card, credit card etc. Manual payments through Demand draft, Banker

cheque, Deposit receipts, FDR etc. are not allowed.

1. NIT HEADER

Name of Work

Design, Manufacturing, Supply, Installation, Testing and Commissioning of Micro processor

based Electronic Interlocking (EI) System in "Hot standby mode" with centralized operation

at 02 stations( KXM & FAR) with dual VDU, Maintenance terminal and operated terminal in

connection with-BFP, RNKA, KXM,FAR - Replacement of signalling gears by - electronic

interlocking .

Bidding type Normal Tender

Tender Type Open Bidding System Two Packet System

Tender Closing Date Time 08/03/2019 15:00 Date Time Of Uploading Tender 07/02/2019 14:44

Pre-Bid Required No Pre-Bid Query Date Time Not Applicable

Advertised Value Tendering Section DHO PWL

Bidding Style Single Rate for Each Schedule Bidding Unit

Earnest Money (Rs.) 1469600.00 Validity of Offer ( Days) 60

Tender Doc. Cost (Rs.) 10000.00 Period of Completion 9 Months

Contract Type Works Contract Category Expenditure

Bidding Start Date 22/02/2019 Are Joint Venture (JV) firms

allowed to bid Yes

Ranking Order For Bids Lowest to Highest

2. SCHEDULE

S.No. Item

Code

Item Qty Qty Unit Unit Rate Basic Value Escl.(%) Estimated Amount

Bidding

Unit

Schedule A-Electronic Interlocking Above/

Below/Par

01

A1 1.00 Lot 53287636.00 53287636.00 AT Par 53287636.00

Item Description:- Design, manufacture and supply of EI system complete with HOT Stand- by architecture as

per RDSO Specn No. RDSO/SPN/192/2005 with latest amendment and all latest applicable TANs issued by

RDSO. This EI mainly consists of Microprocessor equipment, interface equipment, relays, interconnecting

cables,Datalogger and VDU operator consoles with industrial grade fan less PC with 55 inch LED monitors and

Maintenance Terminal PC console for Event and Fault logging with 42" LED monitors (i) Datalogger should be as

per Specn No. IRS-S-99/2006 (Amdt-3) with latest ammendments for monitoring both Digital & Analog inputs with

all external relay contact wiring & networking capabilities with separate PC, VDU, keyboard, and printer (ii)

Embedded Industrial Grade fan less PCs should be of rugged and reliable type like MOXA series V2406, Kontron

MPCX28R, MEN BC50M or similar with compact flash drives designed for working in Non AC Normal environment

. Minimum requirement of Embedded PC for EI shall be as per RDSO TAN document no. STS/E/TAN/3007

version 1.0 dated 2.11.12 or latest. (iii) For Each CPU of EI DC-DC converters shall be provided in N+1

configuration. In addition DC-DC converters will be provided separately for I/O, Communication equipment and

Misc functions in N+1 configuration. DC-DC converters should be made to work so that in case of converter failure

only one system is affected. Installation of Noise filters at input supply. (iv) It should also include racks, fixture,

mounting arrangements, lightening arrestors and any other accessories necessary to make EI system functional.

(v) List of various modules, equipments, sub assemblies, EI racks and other stores and accessories if any with

unit rate, quantity and total cost may be submitted.( Tenderer may submit detailed break up of items and rates as

per format Annexure-1 given in Tender document). (vi) Inspection: By RDSO. However items not covered under

RDSO inspection will be inspected by the Representative of Railways. Note: Special condition of contract and

technical specifications are given in connection with KXM, FAR station Work. Tentative SIP/ Mini diagram of KXM,

FAR station is attached with technical document. The system design shall incorporate details of approved SIP and

its subsequent alteration/ modification till its commissioning. (KXM, FAR Stations).

02

A2 1.00 Lot 3064288.00 3064288.00 AT Par 3064288.00

Item Description:- Set of essential Spares for Electronic Interlocking system based on specification No.

RDSO/SPN/192/2005 with latest amendment or specification and the quantity10% of each type of card and

components supplied vide item no 1 of schedule A, subject to minimum one if 10% is less than one (Item wise

details of spare to be supplied with unit rates has to be submitted. The total cost for all the spares will only be

taken for evaluation.) Annexure-II


TENDER DOCUMENT


of 33 Run Date/Time: 07/02 /2019 14:45 :34

S.No. Item

Code


Bidding

Unit

Schedule B-Item related with electronic interlocking Above/

Below/Par

01

B1 2.00 Job 666540.79 1333081.58 AT Par 1333081.58

Item Description:- Installation, Wiring, Testing & Commissioning of complete Electronic Interlocking system as

per RDSO specification No. RDSO/SPN/ 192/2005 with Hot Standby and latest amendments/ revision for

functioning of Signaling system a t KXM, FAR stations supplied vide Item No.1 of Schedule-A including

transportation of required materials from consignee's depot to site, FAT & SAT. Technical Advisory Notes (TAN)

issued by RDSO time to time on installation practices of EI are to be complied. NOTE: EI equipments are to be

installed and commissioned by OEM at KXM, FAR stations.

02

B2 2.00 Numbers 177690.79 355381.58 AT Par 355381.58

Item Description:- Supply of Laptop based work station for data input and configuration, simulation and

functional testing, diagnostic and trouble shooting and commissioning of EI/SSI system. (Inspection by RDSO)

03

B3 2.00 Set 6692.98 13385.96 AT Par 13385.96

Item Description:- Supply of documents as per technical specifications for Technician, Jr. Engineer. Manual for

Instt.,testing, commissioning & maintenance of the system. (Inspection by Consignee)(Qty- 6 Set for each SSI)

04

B4 2.00 Set 6692.98 13385.96 AT Par 13385.96

Item Description:- Supply of documents for Engineer level-Technical & System Module for diagnostic & Trouble

shooting for repair centre. (Inspection by Consignee)(Qty- 6Set for each SSI)

05

B5 2.00 Set 6692.98 13385.96 AT Par 13385.96

Item Description:- Supply of documents for Higher management level functioning & system over view.

(Inspection by Consignee)(Qty- 6Set for each SSI)

06

B6 2.00 Set 64205.90 128411.80 AT Par 128411.80

Item Description:- Completion documents as per special condition of contract. Each set consisting of 6 copies

each of all completion documents (Inspection by Consignee)

07

B7 2.00 Set 80703.22 161406.44 AT Par 161406.44

Item Description:- Tool Kits & measuring instruments required for Technicians & Jr. Engineers for testig &

maintenance at site. (Inspection by Consignee)

08

B8 2.00 Set 80703.22 161406.44 AT Par 161406.44

Item Description:- Instruments and Tool Kits required for trouble shooting and repair of hardware and software

(Inspection by Consignee)

09

B9 2.00 Station 105632.92 211265.84 AT Par 211265.84

Item Description:- Maintenance & Supervision of compelte SSI/EI equipment installed as per item no 1 for 1 year

as per details of Spl condition of contract. (Inspection by Consignee)

10

B10 2.00 Set 460000.00 920000.00 AT Par 920000.00

Item Description:- Supply and installation of maintenance free special earthing ring arrangement for EI/SSI

system at all locations as per RDSO Specification no. RDSO/SPN /197/2008 with latest amendemnt. All Material

to be supplied by contractor.(Inspection by RDSO )

11

B11 2.00 Set 86827.31 173654.62 AT Par 173654.62

Item Description:- Supply of active lightening arrester of class A for building protection as per standard NFC -17-

102.It shall work on early streamer emission principle and T of 60 micro seconds .A non resettable type counter

shall also be supplied to count the number of lightening occurrences. (Inspection by Consignee)

12

B12 2.00 Set 5521.05 11042.10 AT Par 11042.10

Item Description:- Installation of A class device on the top of the building .The device shall be installed at

suitable height on the roof of the building using GI mast as per instruction of Railway engineer at site. The device

shall be connected to the earth pit using the copper tape of 25mm X 2mm or better, This copper tape will be run

firmly only the side of the mast with the help of spacers. "It shall also be ensured that the down conductor shall no

touch the building throughout .The sown conductor shall be connected to the earth electrode using exothermic

welding .A counter shall b installed at approachable place the accessories like spacers'. welding materials etc

required for installation shall be ranged by the contractor.

S.No. Item

Code


Bidding

Unit

Schedule C-Part-I (Other Supply Items) Above/

Below/Par

CI 01 18.00 Numbers 33951.27 611122.86 AT Par 611122.86


TENDER DOCUMENT


of 33 Run Date/Time: 07/02 /2019 14:45 :34

01

Item Description:- Supply, fixing & erection of Relay Rack, frame, scaffolding and ladder/angle for relay room,

power equipment room, battery room and other places as required, all oven baked and powder coated with Biscuit

Mat colour corrosive resistant and final finish with Grey (Sigma) enameled paint, complete as per standard

drawing with fuse strip, anodized bars/strip for relay bases, Insulators, grouting bolts, tripods, rack fittings, ladder

arrangement, all necessary fitting, supports, insulators, PVC slotted trunking having removable covers suitable for

EI. Fixing of Capacitors, resistors, diodes and other accessories etc. as per drawing and technical specifications &

erection of relay racks with scaffolding arrangement, suitable grounding arrangements, fixing of tag blocks on

relay racks and complete all the accessories as per technical specifications mentioned in Annexure-3 or as per

specification of OEM of Electronic Interlocking suitable for EI installation. ( Inspection by RITES)

02

CI 02 10.00 Numbers 33036.52 330365.20 AT Par 330365.20

Item Description:- Supply, fixing & erection of Cable Termination rack, frame, scaffolding/ladder/angle, all oven

baked and powder coated with Biscuit Mat colour corrosive resistant and final finish with Grey (Sigma) enameled

paint, complete as per standard drawing with fuse strip, anodized bars/strip for relay bases, Insulators, grouting

bolts, tripods, rack fittings, ladder arrangement, all necessary fitting, supports, insulators, PVC slotted trunking

having removable covers suitable for EI. Fixing of Capacitors, resistors, diodes and other accessories etc. as per

drawing and technical specifications & erection of cable termination racks with scaffolding arrangement, suitable

grounding arrangements, fixing of tag blocks on relay racks and complete all the accessories as per technical

specifications mentioned in Annexure-4 or as per specification of OEM of Electronic Interlocking suitable for EI

installation. (Inspection by Consignee)

03

CI 03 140.00 Numbers 2772.91 388207.40 AT Par 388207.40

Item Description:- Supply of QNA-1 8F/8B. Neutral Line ( Metal to carbon) AC Immunized, DC miniature plug in

24V DC 8F-8B front and back contacts QNA1 complete with base, plugboard, retaining clip & connectors PN code

AEDGH conforming to BRS:931A, IRS:S 23 & 34 as applicable with latest amendment. (Inspection by RDSO)

04

CI 04 50.00 Numbers 4000.00 200000.00 AT Par 200000.00

Item Description:- Supply of Relay AC Immunized, plug-in type, Style-QNNA1, Twin DC Neutral line, 24V DC,

6F/2B contacts each for LH & RH, Front and back contacts metal to carbon, complete with plug board, retaining

clips and connectors, Confirming to BRS-960,IRS:S60, IRS S-34 & IRS S-23. Interlocking Pin Code CDEHX.

(Inspection by RDSO)

05

CI 05 28.00 Numbers 6319.72 176952.16 AT Par 176952.16

Item Description:- Supply of (KLCR) Relay Key Lock metal to metal neutral relay, special type, conforming to

IRS:S-46 or with latest amendment / specification, working on 60/24V D.C. configuration 4F/4B or as specified.

With key and key wards of approved type ( Inspection by Consignee)

06

CI 06 130.00 Numbers 2200.48 286062.40 AT Par 286062.40

Item Description:- Supply of RELAY TRACK PLUG-IN TYPE 9 OHM AC Immunized, latest contact configuration,

style QTA-2 Spec No. BRS: 938A, 939A & 966, complete with base, plug board, retaining clip & connectors.


07

CI 07 20.00 Kg 703.31 14066.20 AT Par 14066.20

Item Description:- Supply of solder Wire Resin core 60/40, 18 SWG (PHILCO/KHOSLA/ Approved Make) (

Inspection by Consignee)

08

CI 08 400.00 Numbers 37.02 14808.00 AT Par 14808.00

Item Description:- Supply of Lacing thread rolls, black, wax coated (100 mtrs each thin & thick in the ratio of 3:4.(

Inspection by Consignee)

09

CI 09 600.00 Numbers 20.00 12000.00 AT Par 12000.00

Item Description:- Supply of Adhesive tape rolls, PVC (19mm x 10 mtrs steel grip make in four colours Red, Blue,

Yellow & black in equal quantity. ( Inspection by Consignee)

10

CI 10 700.00 Numbers 634.59 444213.00 AT Par 444213.00

Item Description:- Supply of 16/0.2mm size tinned flexible single core indoor wire IRS:S 76*89 Amend No.2 or

with latest amendment / specification, PVC coated in different colours as per technical specifications and to be

supplied in coils of 100 meters. (Inspection by Consignee )

11

CI 11 1.40 Kilometre 2700.00 3780.00 AT Par 3780.00

Item Description:- Supply of indoor jumper wire ATC 1 x 0.6 mm dia as per specification IRS/S/76/89 with latest

amendment. (for size/parameters not covered by IRS-76/89 relevant clauses of IS-694/77 with latest amendment

will be applicable) ( Red, Black & Grey) (Inspection by Consignee)

12


Item Description:- Supply of indoor jumper wire ATC, 1 x 1mm dia in different colours as per requirement. as per

specification IRS/S/76/89 with latest amendment. (for size/parameters not covered by IRS-76/89 relevant clauses

of IS-694/77 with latest amendment. will be applicable) (Inspection by Consignee)

13



TENDER DOCUMENT


of 33 Run Date/Time: 07/02 /2019 14:45 :34

Item Description:- Supply of Power wire (copper, multi stand) as per IS 2465/1984 & IS 694/1990 ( 1 x 6 Sq mm)

85 conductor each dia 0.30+/- 0.01 with insulation thickness of 1.55mm nominal conductor resistance 3.14

ohms/km and test parameters as per IRS(S)76/89. ( Inspection by Consignee)

14


Item Description:- Supply of flexible cable single core Red & Black color multi strand 1x 10Sq mm as per IRS

76/89 with latest amendment.(Inspection by Consignee)

15


Item Description:- Supply of Power wire (copper, multi stand) as per IS 2465/1984 & IS 694/1990 ( 1 x 16 Sq

mm) 101 conductor each dia 0.45+/- 0.01 with insulation thickness of 1 2mm nominal conductor resistance 1.127

ohms/km and test parameters as per IRS(S)76/89. (Inspection by Consignee)

16


Item Description:- Supply of Power wire (copper, multi strand) as per IS 2465/1984 & IS 694/1990 , 1x 25 Sq mm

(Red and Black each) (Inspection by RDSO)

17

CI 17 850.00 Metre 206.00 175100.00 AT Par 175100.00

Item Description:- Supply of PVC insulated multi strand 35 Sq. mm. Cu Cable as per IS:694 or latest for

connecting earth bus bar to earth electrode as per RDSO Drawing SDO/RDSO/E&B/001 OR LATEST. (Inspection

by Consignee)

18

CI 18 8.00 Numbers 181500.00 1452000.00 AT Par 1452000.00

Item Description:- Supply installation, wiring, testing and commissioning of ELD as per RDSO/SPN /256/2002 or

latest (12 channel) (Inspection by RDSO)

19

CI 19 4.00 Numbers 60208.00 240832.00 AT Par 240832.00

Item Description:- Supply of Isolation transformer 10 KVA, input and output 230V AC 50 Hz Sine Wave Single

phase, as per technical specifications (Annexure - 5). (Inspection by Consignee)

20

CI 20 8.00 Numbers 8088.81 64710.48 AT Par 64710.48

Item Description:- Supply & Installation of program switches snap action bas mounting type along with cover and

mounting bracket 63A-9 pole as per drawing no. RST-C. 106 or latest alteration. (Inspection by Consignee)

21

CI 21 5312.00 Numbers 693.80 3685465.60 AT Par 3685465.60

Item Description:- Supply of Signaling Circuit Automatic Fuse changeover Module for 2-6 Amperes with standby

fuse for 12V/24V/60V DC or 110V AC complete unit with mounting accessories on DIN rail in enclosure of

approved type, two ( NO+NC) potential free contacts for remote monitoring, changeover time less than 1 milli

seconds and Audio Visual Alarm and indications for main and standby fuse, including installation, all as per

technical specifications to monitor the fuses of various voltages and currents provided for various signaling

functions in location boxes as per RDSO specifications RDSO/SPN/209/2012 Rev.1.0 or latest amendment,

(Inspection by RITES.)

22

CI 22 28.00 Numbers 6598.50 184758.00 AT Par 184758.00

Item Description:- Supply of Portable Halon type/similar type Fire Extinguishers 1 kg. Capacity with squeeze grip

valve high pressure discharge, nozzle and fitted with pressure gauge to conform IS: 11108 of 1984 duly charged

with halon 1211 (Chloride Dilfer) in conformity to IS:111070. (Inspection by Consignee)

23

CI 23 142.00 Numbers 20714.43 2941449.06 AT Par 2941449.06

Item Description:- Supply of apparatus case steel single with 'E' type lock and Key ward No. 42, as per sketch

No. RE / S & T / AID / SK / 219 / 82 with Alt 'A' & 221 / 82 with Alt. 'B'. The key and handle should be at the rate of

one each per 4 Nos. apparatus case. (Inspection by RITES)

24

CI 24 70.00 Numbers 15984.58 1118920.60 AT Par 1118920.60

Item Description:- Supply of apparatus case half steel RE Type fitted with 'E' type lock and key ward No. 42 and

handle single as per Drg. No. Sketch No. RE / S & T / AID / SK / 220 / 82 with Alt 'B' & 221 / 82 with Alt. 'B'.

(Inspection by RITES)

25

CI 25 19600.00 Numbers 144.16 2825536.00 AT Par 2825536.00

Item Description:- Supply of Disconnect Terminal block for Four conductors with screw less Cage Clamp

type/sliding switch disconnect as per RDSO Specification No. RDSO/SPN/189/2004 version 1.2, for each

conductor size upto 2.5 sq. mm. Equivalent of M6 Terminals. Each Terminal block equipped with two markers on

top and bottom, an end plate, 2 end clamps & adequate length rails for fitting terminal blocks. ( Inspection by

RITES)

26

CI 26 1100.00 Numbers 68.01 74811.00 AT Par 74811.00

Item Description:- Supply of Non Deteriorating type low voltage Cartridge fuse rated current 2/4Amp. round head

type as per Spc. No. IRS.S 78/92 with latest amendment. inspection by RDSO.

27

CI 27 100.00 Numbers 72.09 7209.00 AT Par 7209.00

Item Description:- Supply of Non deteriorating type low voltage cyndrical head cartridge Electric fuse 6/10 AMP

as per Specn. No. IRS/S/78/92 with latest amendments. inspection by RDSO.

CI 28 900.00 Numbers 129.17 116253.00 AT Par 116253.00


TENDER DOCUMENT


of 33 Run Date/Time: 07/02 /2019 14:45 :34

28 Item Description:- Supply of FUSE BLOCK MADE OF PBT /POLYCARBONATE as per IRS S 75/2006 & RDSO

Drg No. SA-23748 . Alt 4 suitable for cartridge fuse block cyndrical head fuse links. inspection by RDSO.

29

CI 29 54.00 Numbers 5102.01 275508.54 AT Par 275508.54

Item Description:- Supply of Paper base, resin bonded, Phenolic laminated sheet, conforming to 10 mm thick IS-

2036 of 1974 grade P3 in standard size of 1.22 Mtr. X 1.22 Mtr. Manufacturer test certificate to be submitted by

contractor. (Inspection by Consignee)

30

CI 30 44.00 Numbers 126688.00 5574272.00 AT Par 5574272.00

Item Description:- Supply of Point Machine IRS type 220 mm Stroke clamp type as per IRS S-24/2002 (

Amendment 1 or latest) (Inspection by RDSO)

31

CI 31 12.00 Numbers 85600.00 1027200.00 AT Par 1027200.00

Item Description:- Supply of Electric Point Machine IRS make, 110V DC operation (AC immunity 160V)

NONTRAILABLE, complete with lock, detector, cable termination box and slides for lock and detector (Rotary

locking) as per IRS: S24/2002. 1 set of tools (M6/M8/M18/M20/M22 Box spanners, M10/M12 spanners, adjustable

wrench and a screw driver 300 mm long in a suitable tool box) with every eight machines or less as stipulated in

the RDSO's specification should be supplied.(Inspection by RDSO)

32

CI 32 44.00 Numbers 23245.75 1022813.00 AT Par 1022813.00

Item Description:- Fabrication and supply of point rodding (Ground Connection )set with insulation complete set

including for D Bracket and "L" bracket insulation, for electric point machine 220 mm stroke Clamp type for thick

web switches to suite RDSO Drg no RDSO/S/11000 & RDSO/S-3395 (Inspection by Consignee)

33

CI 33 12.00 Numbers 10623.18 127478.16 AT Par 127478.16

Item Description:- Fabrication and supply of point rodding (Ground Connection) set with insulation complete set

including for D Bracket and "L" bracket insulation, for electric point machine (RDSO Type) as per RDSO Drg. No.

RDSO / S / 3301-02.(Inspection by Consignee)

34

CI 34 8.00 Numbers 2177.99 17423.92 AT Par 17423.92

Item Description:- Supply and Installation of (KLCR Box) Wooden crank handle lock inside up box, for fixing of

EKT on wooden board inside box for installing KLCRs/EKTs UPTO 6 Nos in the same, including suppiy of all

materials like board, handle, hinges, Godrej type padlock, glass sheet etc (Inspection by consignee)

35

CI 35 112.00 Set 256.33 28708.96 AT Par 28708.96

Item Description:- Supply of Point's william stretcher bar insulation complete set as per RDSO Drg. No. SA 9151-

52 or latest with latest amendments complete with nut bolts etc (Inspection by consignee).

36

CI 36 80.00 Set 256.33 20506.40 AT Par 20506.40

Item Description:- Supply of Points gauge tie plate insulation complete set as per CSTE's Drg. No. SK/85/25

complete with nut bolts etc. (Inspection by consignee)

37

CI 37 52.00 Numbers 2063.45 107299.40 AT Par 107299.40

Item Description:- Supply & fixing of GI bend pipe 'B' class 50 mm . Dia for cable entry in point machines with

suitable bent and all fitting accessories . (Inspection by Consignee)

38

CI 38 260.00 Numbers 2538.28 659952.80 AT Par 659952.80

Item Description:- Supply of CHOKE -'B' TYPE Spec. No. IRS:S-65/83 Amendment No.3 or with latest

amendment/ specification. (Inspection by RDSO)

39

CI 39 130.00 Numbers 1102.90 143377.00 AT Par 143377.00

Item Description:- Supply of TRACK FEED RESISTANCE - 'DISC' TYPE DRG No.SA-20161-66/M.(Inspection by

RDSO)

40

CI 40 130.00 Numbers 2257.45 293468.50 AT Par 293468.50

Item Description:- Supply of Battery charger Track feed Self Mounting Type Spec No.: IRS:S-89-93 with

Amendment-2 or with latest amendment/ specification rating 110V AC/ 2 to 6V DC, 3-10 Amps Trickle charge :

0.1A to 0.5A.Boost Charge : 1A to 3 Amp.with potential free contact for remote monitoring.(Inspection by RDSO)

41

CI 41 404.00 Numbers 5614.57 2268286.28 AT Par 2268286.28

Item Description:- Supply of Track Lead Junction Box (TLJB) 4 way in box size 250x255x120 mm, 6 mm thick

made from FRP (SMC) Glass Fiber Reinforced Polyester as per RDSO specification No. RDSO/SPN/151/1997,

Hot compression moulded IP 66 protection class, with tongue & groove sealing system having chloroprene seal,

cover and base system fastened by captive lid stainless steel screws, flammability characteristics compliant to

UL94 VO, grey colour, minimum 25 % glass content, fitted with PBT/Wago terminals of required size for

cable/track lead connections, including cable entry and exit systems at the bottom for required cable /track lead

connection size with polyamide gland and 2 nos. FRP angles white colour with nuts and bolts, size 40x40x6 mm

having fire retardent characteristics as per UL94 V1, for fixing TLJB and all required accessories.(Inspection by

RITES)

42

CI 42 390.00 Numbers 1901.29 741503.10 AT Par 741503.10


TENDER DOCUMENT


of 33 Run Date/Time: 07/02 /2019 14:45 :34

Item Description:- Supply of Secondary cells 2 V, 80 AH Low Maintenance with topping frequency up to 6

months, as per specification no. IRS: S-88/2004 uncharged complete with inter cell connectors, nuts and bolts etc.


43

CI 43 24.00 Set 2846679.31 68320303.44 AT Par 68320303.44

Item Description:- Supply of Digital Axle counter multi section type (MSDAC) complete system equipped including

the central evaluator and final track clearance relay for each section. Detection points, track side electronics, reset

boxes, LV boxes etc with all other accessories including deflector plates. Housing of track side electronics fully

wired and fully equipped for 8 detection points & 6 track sections as per RDSO specification no.

RDSO/SPN/176/2005(ver.2) or latest. The MSDAC system supplied shall have approval /cross approval of RDSO

and inspected by RDSO. (6 track section and 8 detection points )

44

CI 44 164.00 Numbers 335.71 55056.44 AT Par 55056.44

Item Description:- Supply of Hydrometer, Exide makes or similar for measuring specific gravity of battery graded

acid with mounting stand in location boxes. Consignee inspection under manufacturer certificate.(Inspection by

Consignee)

45

CI 45 11.00 Numbers 554905.39 6103959.29 AT Par 6103959.29

Item Description:- Supply of Compact portable Gasoline Rail Drill Machine with belt cover, Drilling Capacity 6 to

36 mm, Suitable for 52 Kg, 60 Kg, Tongue rail, Point m/c base plate, 2 stroke engine, Weight: Approx 15 kg w/o

attachment, Machine size (Max):- H x Lx W: 500 x 350 x260 mm Barrel Dia: 52 ±1 mm, Tack Time: Approx Drilling

- 45 sec, Clamping- 25 Sec, Decamping- 15 Sec. (Inspection by Consignee)

46

CI 46 100.00 Numbers 899.78 89978.00 AT Par 89978.00

Item Description:- Supply of DC Track circuit bond:- length 1.4 meter in stainless steel (Non Magnetic) Multi

stand wire 10 sq mm 2 layer insulation with SS (Non Magnetic) Web pin for fit designing and other side SS (Non

Magnetic) Lug. Contractor should get the approval of sample from Railway Engineer (i.e Sr.DSTE/AGC) before

supply. (Inspection by Consignee)

47

CI 47 160.00 Numbers 1250.98 200156.80 AT Par 200156.80

Item Description:- Supply of DC Track circuit bond:- length 2 meter in stainless steel (Non Magnetic) Multi stand

wire 10 sq mm 2 layer insulation with SS (Non Magnetic) Web pin for fit designing and other side SS (Non

Magnetic) Lug. Contractor should get the approval of sample from Railway Engineer (i.e Sr.DSTE/AGC) before

supply. (Inspection by Consignee)

48

CI 48 144.00 Numbers 1707.64 245900.16 AT Par 245900.16


wire 10 sq mm 2 layer insulation with SS (Non Magnetic) web pin for fit designing and other side SS (Non

Magnetic) Lug. Contractor should get the approval of sample from Railway Engineer (i.e. Sr.DSTE/AGC) before

supply.(Inspection by Consignee)

49

CI 49 160.00 Numbers 2164.30 346288.00 AT Par 346288.00





50

CI 50 144.00 Numbers 2622.85 377690.40 AT Par 377690.40





51

CI 51 52.00 Numbers 18579.99 966159.48 AT Par 966159.48

Item Description:- Supply of Colour light signal post tubular steel 140 mm dia, as per IRS 56/81, Length 3.5m -

5.5m long, as per requirement, complete with Signal base as per RDSO drg. S 2011/M, ladder with base, ladder

guards platform, MS supporting bracket to support ladder, front staging etc. Front staging platform to be as per

site in charge's instructions. (Inspection by RITES)

52

CI 52 40.00 Numbers 518.17 20726.80 AT Par 20726.80

Item Description:- Fabrication, supply and fixing of 'P', 'C', 'A', 'G', 'IBS' etc. marker disk painted and lettered with

enameled paint of approved colors, on signals, conforming to RDSO Drg. No.SA - 23456, as per standard practice

and technical specifications. (Inspection by Consignee)

53

CI 53 12.00 Numbers 7547.20 90566.40 AT Par 90566.40

Item Description:- Supply and installation of stop Board/BSLB/ Goods Warning Board or other boards, making

foundation, complete with contractor material .supply and painting the board & post as per approved colour

scheme complete installation as per tech. specifications. (Inspection by Consignee)

54

CI 54 8.00 Numbers 5660.40 45283.20 AT Par 45283.20


TENDER DOCUMENT


of 33 Run Date/Time: 07/02 /2019 14:45 :34

Item Description:- Supply and installation of calling on boards or other boards ,making foundation ,complete with

contractor material .supply and painting the board & post as per approved colour scheme complete installation as

per tech. specifications. (Inspection by Consignee)

55

CI 55 16.00 Numbers 25774.92 412398.72 AT Par 412398.72

Item Description:- Supply of Two aspect Colour light signal unit non metallic complete to RDSO Specification

RDSOP/SPN/194/2006 Version 1, made of FRP to RDSO Specification RDSOP/SPN/151/1997 & RDSO drg

No.SA-23003A/M (Adv), or all to latest amendments or specifications, without signal transformer light unit & double

lenses . (Inspection by Consignee)

56

CI 56 3.00 Numbers 36382.89 109148.67 AT Par 109148.67

Item Description:- Three aspect Colour light signal unit non metallic complete to RDSO Specification



lenses (Inspection by Consignee).

57

CI 57 33.00 Numbers 33370.33 1101220.89 AT Par 1101220.89

Item Description:- Supply of Four aspect Colour light signal unit non metallic complete to RDSO Specification



lenses . (Inspection by RITES)

58

CI 58 14.00 Numbers 824.68 11545.52 AT Par 11545.52

Item Description:- Supply of Offset bracket for colour light signal Main unit, with fixing U clamps & nuts etc., as

per RDSO Drg. No. SA 23080 (Adv.) with latest amendments. (Inspection by Consignee)

59

CI 59 32.00 Numbers 1085.44 34734.08 AT Par 34734.08

Item Description:- Supply of Off set bracket for colour light signal with fixing U clamps & nuts etc. (Shunt /Co-On)


60

CI 60 4.00 Numbers 40802.02 163208.08 AT Par 163208.08

Item Description:- Supply of Direction type route indicator,1 - way as per IRS: S-66/84, non metallic complete to

RDSO Specification RDSOP/SPN/194/2006 Version 1and RDSO Specification RDSOP/SPN/151/1997 for FRP,

made of FRP to Drg. No.SA-23402(Adv) Alt-4 or all to latest amendments or specifications, complete with fixing

arrangement, brackets, hoods and terminals but without lamps, lamp holders and lenses.(Inspection by

Consignee)

61

CI 61 4.00 Numbers 30787.78 123151.12 AT Par 123151.12

Item Description:- Supply of Direction type route indicator,2 - way as per IRS: S-66/84, non metallic complete to

RDSO Specification RDSOP/SPN/194/2006 Version 1and RDSO Specification RDSOP/SPN/151/1997 for FRP,

made of FRP to Drg. No.SA-23402(Adv) Alt-4 or all to latest amendments or specifications, complete with fixing

arrangement, brackets, hoods and terminals but without lamps, lamp holders and lenses.(Inspection by

Consignee)

62

CI 62 18.00 Numbers 1859.24 33466.32 AT Par 33466.32

Item Description:- Supply of Shunt signal position light post as per IRS 56/81, complete with bracket, Post as per

IRS-S-6 of 1981 having 4.5mm thickness & minimum 1m length, surface base, etc. (Inspection by Consignee)

63

CI 63 26.00 Numbers 11380.16 295884.16 AT Par 295884.16

Item Description:- Supply of Shunt signal position light type non metalic complete to RDSO Specification

RDSOP/SPN/194/2006 Version 1and RDSO Specification RDSOP/SPN/151/1997 for FRP, made of FRP to Drg.

No. SA-23840(Adv) Alt-2 for dependent/independent type complete with signal unit, bracket, terminals etc. but

without lenses, lamps and lamp holders (Inspection by Consignee)

64 CI 64 110.00 Numbers 341.32 37545.20 AT Par 37545.20

Item Description:- Supply of hand cuff lock with key of approved type of signal units. (Inspection by Consignee)

65

CI 65 10.00 Numbers 8194.86 81948.60 AT Par 81948.60

Item Description:- Supply of Calling-On signal unit non metallic complete to RDSO Specification

RDSOP/SPN/194/2006 Version 1and RDSO Specification RDSOP/SPN/151/1997 for FRP, made of FRP complete

with fixing clamps, terminals etc. as per as per RDSO drawing SA-24351 (Adv.) Alt-1 but without lamp, lamp holder

and lens. Fixing arrangement shall be as per RDSO drawing SA-24352 (Adv). (Inspection by Consignee)

66

CI 66 300.00 Numbers 518.17 155451.00 AT Par 155451.00

Item Description:- Supply & fixing of Retro-Reflective number plates of approved type. As per Drg. No.

Sig.05/2009 dtd 02.04.09. (Contractor has to arrange all hardware & other requirement to fix the plate on signal at

his own cost.) (Inspection by Consignee)

67

CI 67 10.00 Numbers 6630.00 66300.00 AT Par 66300.00

Item Description:- Supply of 'A/AG' marker LED signal lightting unit.110V AC retrofit able in existing CLS housing

and complete with AC LED ECR/ AC conventional as per RDSO Specn No. RDSO/SPN/153/2004 Rev-3.0 (Drft or

latest).(Inspection by Consignee)


TENDER DOCUMENT


of 33 Run Date/Time: 07/02 /2019 14:45 :34

68

CI 68 400.00 Metre 646.68 258672.00 AT Par 258672.00

Item Description:- Supply of GI pipe with thread collars of 100 mm nominal bore, specn. No IS 1239 medium

grade, to be perforated after supply for required length , as per technical spech.( Inspection by Consignee)

69

CI 69 1800.00 Metre 193.68 348624.00 AT Par 348624.00

Item Description:- Supply of DWC Size of Outer Dia 90 mm / inner dia 76 mm, having non flame propagation and

anti rodent properties, electric/telerex/optirex or similar as per TEC specifications GR/DWC - 34/01, IS 14930 part-

II, and technical specifications, along with socket/coupler and T joints wherever required having IP-67 protection,

for underground power/ signalling/ telecommunication cable protection. ( Inspection by Consignee)

70

CI 70 3200.00 Metre 351.85 1125920.00 AT Par 1125920.00

Item Description:- Supply of DWC Size of Outer Dia 175 mm / inner dia 148 mm, having non flame propagation

and anti rodent properties, electrex/telerex/optirex or similar as per TEC specifications GR/DWC - 34/01, IS 14930

part-II, and technical specifications, along with socket/coupler and T joints wherever required having IP-67

protection, for underground power/ signaling/ telecommunication cable protection. (Inspection by RITES)

71

CI 71 355.00 Numbers 361.54 128346.70 AT Par 128346.70

Item Description:- Supply & fixing of Cable route marker of stone of approved type in size 1.2 mtr x 0.2 mtr x 0.1

mtr with maximum 5 % tolerance on maximum 5% markers, engraved 'NCR" "S&T" on top portion. (Inspection by

Consignee)

72

CI 72 70.00 Numbers 1692.55 118478.50 AT Par 118478.50

Item Description:- Supply of Cable jointing heat shrinkable type kit from RDSO approved source

RAYCHEM/REPL make for 12 C/19 C/24 C/30 C signaling cable. (Inspection by Consignee)

73

CI 73 12738.00 Metre 17.97 228901.86 AT Par 228901.86

Item Description:- Supply and placing of one layer of standard size 'B' grade quality bricks of the local make and

spreading on cables laid breadth wise, as per technical specifications. NOTE : If size of bricks to be supplied is

less than the minimum size specified in the drawing. (Inspection by Consignee)

74

CI 74 4.00 Set 312326.36 1249305.44 AT Par 1249305.44

Item Description:- Supply of Electrically operated lifting barrier set as per specification no. RDSO/SPN/208/2012

(vER. 2) or latest, with GI Boom in octagonal shape as RDSO standard drawing no. RDSO/S 11600 and Motorized

Boom Locking, to work on 24VDC, each set consisting of 2 Nos. of 32ft. Long Aluminum barrier with stop boards &

lights, 2 Nos. of lifting barrier pedestals each with 8 contacts circuit controllers with top roller type limit switches of

minimum 10000 operations life cycle, hand crank, 2 electric motors, M.S. Counterweights, 2 Nos. of Boom stops

with boom locking, along with panel to have necessary switches/buttons to operate one or both barriers, operate

boom lock only, or operate with push buttons in case of 24 V DC is available..(Inspection by RITES)

75

CI 75 4.00 Numbers 7621.85 30487.40 AT Par 30487.40

Item Description:- Supply of gate signal operation cum indication panel consisting of 2-way switches, LED

indications etc. as per standard practice. This panel shall be used in lieu of the puller slide. (Inspection by

Consignee)

76

CI 76 18.00 Numbers 2640.81 47534.58 AT Par 47534.58

Item Description:- Supply of Desk type Electronic magneto Telephone as per RDSO Spec. no.IRS: TC79/2000

amendment no.2 or latest. (Inspection by Consignee)

77

CI 77 8.00 Numbers 54165.80 433326.40 AT Par 433326.40

Item Description:- Supply of Road signal complete with signal post CLS unit 3 aspect ,ladder ,Base , LED signals

& Hooter etc. (Inspection by RITES)

78

CI 78 4.00 Set 71936.55 287746.20 AT Par 287746.20

Item Description:- Design Manufacturing and supply of sliding boom arrangement, as per drawing no.

Agra/S/305/SBB/009.(Inspection by RITES)

79

CI 79 4.00 Set 596529.13 2386116.52 AT Par 2386116.52

Item Description:- Supply, installation & commissioning of High Availability Digital Axle Counter consisting of

Single section type as per RDSO spec. No. RDSO/SPN/177/2005 (Ver-2) with amend-1 or latest phase reversal

type. (Inspection by RDSO)

80

CI 80 5.00 Set 82584.60 412923.00 AT Par 412923.00

Item Description:- Supply of Tool kits for Digital Axle counter as per RDSO specification RDSO/SPN/177/2012

(Version 3) for SSDAC with latest amendment or specification for type/types of DAC being supplied.(Inspection by

Consignee)

81

CI 81 4.00 Set 25856.00 103424.00 AT Par 103424.00

Item Description:- Supply of Measuring instrument set for measuring all the track side and processor parameters

of Digital Axle counter as per RDSO specification No. RDSO/SPN/177/2012 Version No. 3 or latest amendment or

specification/RDSO specification RDSO/ SPN/ 177/2012 (Version 3) Or RDSO/SPN/177/2003 (Version 1)

Amendment 2/RDSO specification RDSO/SPN/176/2005 (Version 2) or MSDAC/SSDAC with latest amendment or

specification for type/types of DAC being supplied.(Inspection by Consignee)


TENDER DOCUMENT


of 33 Run Date/Time: 07/02 /2019 14:45 :34

82

CI 82 4.00 Set 17686.42 70745.68 AT Par 70745.68

Item Description:- Supply and installation of basic earth materials to construct unit maintenance free earth

consisting as per RDSO Spec no. RDSO/SPN/197/2008 consisting of following items:-(Inspection by Consignee)

(1) Copper bonded steel electrodes of 3.0 m long, 17.2 mm dia with copper bonding thickness of min 350 micron

and UL listed and marked 1 no. (2) Earth enhancement material supplied in sealed bags of minimum 10 kgs 3

nos. (3) Copper strip 150x25x6 mm to terminate earth end - 1 no.,(4) Copper strip 3000x25x6 mm (MEEB) - 1 no.

(5) Copper strip 150x25x6 mm (SEEB) - 1 no.

83

CI 83 5.00 Numbers 1876.82 9384.10 AT Par 9384.10

Item Description:- Supply of Domino units with cover plate as per approved panel diagram, each of size 54x34

mm completely wired up similar to Siemens make each domino units should have all the 15 contact terminals

wired up.(Inspection by Consignee)

84

CI 84 20.00 Set 4936.27 98725.40 AT Par 98725.40

Item Description:- Supply & installation of A set CLASS C Surge Protection System for connecting between Line

& Neutral with inbuilt thermal isolating device suitable for single phase power supply with visual indication and

potential free contacts suitable for 110 V AC/DC application with neutral systems all conforming to RDSO

specification No. RDSO/SPN/144/2004 or latest and configuration conforming to technical specifications.


85

CI 85 204.00 Job 2714.21 553698.84 AT Par 553698.84

Item Description:- Supply & installation of earth electrode assemble as per Drg. No. DRM/S&T/JHS/ 214 . This

also includes fixing of earth electrodes, earthing of S & T apparatus cases along with all equipments and cable

armors along with soldering at all locations as decided by the site engineer of the Railways, signal post etc

connected through cable/GI wire 8 SWG supported on MS flat size 5mm x 40 mm to earth electrodes as per drg

DRM/S&T/JHS /214 and practice on the division. Suitable brick masonry enclosure to be provided around the

earth. The earth value should be less than 10 ohms including the lead wire. It should be measured and painted on

it. (Inspection by RITES)

86

CI 86 98.00 Set 13790.00 1351420.00 AT Par 1351420.00

Item Description:- Supply of A set of complete Earthing and Bonding system as per code of practice

RDSO/SPN/197/2008 or latest, to construct earthing of </= 1 Ohm, mainly consisting of Copper bonded high

tensile low carbon Steel pipe Earth electrode of minimum 3.0 meter length, 17 mm diameter with copper strip of

150mmx25mmx6mm exothermically welded to earth electrode as per drawing SDO/RDSO/E&B/001 or latest, with

set of steel nuts & bolts for earth cable connections and Earth enhancement material 30-35 Kg mainly consisting

of Graphite and Portland cement with negligible Bentonite content. inspection by RITES.

87

CI 87 2.00 Numbers 140000.00 280000.00 AT Par 280000.00

Item Description:- Supply of FEP for networking. IRS:S-99/2006 Amend.3 or latest. ( Inspection by Consignee)

(Annexure -6 )

88

CI 88 4.00 Numbers 354000.00 1416000.00 AT Par 1416000.00

Item Description:- Supply & installation of Computer Maintainer's console with 42 " display unit. (Industrial

embedded PC)(Inspection by Consignee)

89

CI 89 4.00 Pair 17791.90 71167.60 AT Par 71167.60

Item Description:- Supply of Modem 2Mbps G.703 & V.35 as per RDSO spec. RDSO/SPN/TC/80/2008. REV. 0.0

or latest. (Inspection by Consignee)

90 CI 90 4.00 Numbers 4212.37 16849.48 AT Par 16849.48

Item Description:- Supply of Switches 8 port D-link or better make.(Inspection by Consignee)

91 CI 91 200.00 Metre 14.39 2878.00 AT Par 2878.00

Item Description:- Supply of PVC indoor cable 05pair 0.5mm from reputed sources(Inspection by Consignee)

92

CI 92 8.00 Pair 16938.72 135509.76 AT Par 135509.76

Item Description:- Supply & Installation and commissioning of LAN extender 4 Port as per

RDSO/SPN/TC/82/2008. Rev 0.0 or latest.(Inspection by Consignee)

93 CI 93 200.00 Metre 26.35 5270.00 AT Par 5270.00

Item Description:- Supply of CAT-6 data cable make D-Link or better make. (Inspection by Consignee)

94 CI 94 40.00 Numbers 5.50 220.00 AT Par 220.00

Item Description:- Supply of RJ-45 connectors D-Link make or better make. (Inspection by Consignee)

95

CI 95 2.00 Numbers 21991.20 43982.40 AT Par 43982.40

Item Description:- Supply , testing and commissioning of 1KVA UPS with 3 hour backup of APC/ DELTA/ Aplab

(ATUT) Make only (Inspection by Consignee)

96

CI 96 4.00 Numbers 160525.00 642100.00 AT Par 642100.00


TENDER DOCUMENT


of 33 Run Date/Time: 07/02 /2019 14:45 :34

Item Description:- Supply of battery monitoring unit for 110V as per specification with 24V/4 Amps SMPS charger

230V A.C. (1 Nos. ) Along with 12V , 18 AH battery(2 Nos.) , Opto to RS485 Converter to interface with Data

Logger, supply of User Interface Module as per Technical specification (Annexure- 7). Note-unit should be connect

with existing D/Lat station and networking with central place (Control room) (Inspection by Consignee)

97

CI 97 2.00 Numbers 180300.00 360600.00 AT Par 360600.00

Item Description:- Supply of power monitoring system with 40" LED screen as per specification. (Annexure-8 ).


98

CI 98 2.00 Station 33975.00 67950.00 AT Par 67950.00

Item Description:- Supply installation testing & commissioning of power Monitoring software for 16/32 Analog

channels (Annexure-9 ). (Inspection by Consignee)

99 CI 99 2.00 Numbers 4212.37 8424.74 AT Par 8424.74

Item Description:- Supply of Switches 8 port D-link or better make.(Inspection by Consignee)

100

CI 100 2.00 Station 162000.00 324000.00 AT Par 324000.00

Item Description:- Supply and Installation of Microprocessor based Event Logger for point machine and DC track

circuit monitoring in relay room, along with two nos of high gain antennas to receive data from Mini Loggers

installed in Location Box units as per Specifications (Annexure-10). {Note-unit should be connect with existing D/L

at station and networking with central place (Control room)} (Inspection by Consignee)

101

CI 101 18.00 Numbers 62400.00 1123200.00 AT Par 1123200.00

Item Description:- Supply and Installation of Microprocessor based Mini Logger installed in location Boxes to

monitor 16 Digital Inputs (Relays), 6 Current Channels of 3 DC Track circuits or 3 Point machine and 4 voltage

channels ( 110 V DC - 01 No, 24 V DC- 01 No., 9v DC -2 Nos) along with one no. low gain antenna to transfer

data to the event logger in the relay room unit as per Specification (Annexure- 11 ). { Note-unit should be connect

with existing D/L at station & and networking with central place (Control room)} (Inspection by Consignee)

102

CI 102 2.00 Station 174000.00 348000.00 AT Par 348000.00

Item Description:- Supply and Installation of Failure Analysis System (01 no. FAS for each station), along with

software. (Inspection by Consignee) (Annexure-12 )

103 CI 103 2.00 Station 80000.00 160000.00 AT Par 160000.00

Item Description:- Installation & wiring of data logger equipment's and other accessories (Per Station)

104 CI 104 4.00 Numbers 22900.00 91600.00 AT Par 91600.00

Item Description:- Installation , Testing and Commissioning of Battery Monitoring unit.

105 CI 105 2.00 Numbers 10000.00 20000.00 AT Par 20000.00

Item Description:- Installation of Analog/Power Monitoring system with Display Screen Complete

106

CI 106 2.00 Numbers 62637.75 125275.50 AT Par 125275.50

Item Description:- Supply, installation & commissioning of portable operator console for onsite programming as

per specification mentioned in (Annexure- 13) loaded with all types required software for the system. (Inspection

by Consignee)

107

CI 107 500.00 Kg 530.88 265440.00 AT Par 265440.00

Item Description:- Solar heat re-radiating membrane coating paint white as per technical specifications.


108

CI 108 250.00 Kg 118.08 29520.00 AT Par 29520.00

Item Description:- Anticorrosive Weather Coat Zinc phosphate primer cum surface coat for Solar heat re-

radiating membrane coating paint white as per technical specifications. (Inspection by Consignee)

109

CI 109 250.00 Kg 206.40 51600.00 AT Par 51600.00

Item Description:- Glaze coat paint for final coating on Solar heat re-radiating membrane coating paint white as

per technical specifications. (Inspection by Consignee)

110

CI 110 350.00 Kg 97.92 34272.00 AT Par 34272.00

Item Description:- Thinner for removing all oil and foreign particles for application of Solar heat re-radiating

membrane coating paint white as per technical specifications (Inspection by Consignee).

111

CI 111 2.00 Station 25544.94 51089.88 AT Par 51089.88

Item Description:- Scrapping, removing of old paint and applying single coat of anticorrosive Weather Coat Zinc

phosphate primer & thinner and two coats of Solar heat re-radiating membrane coating paint and one coat of

Glaze coat paint on Relay rooms. Relay Huts walls/roof of brick/PVC structure and all newly installed gears like

signals, metallic locations,/JBs /point machine covers.

112

CI 112 2.00 Station 70924.60 141849.20 AT Par 141849.20


TENDER DOCUMENT


of 33 Run Date/Time: 07/02 /2019 14:45 :34

Item Description:- Supply of paints, primers, varnish and other painting material, complete painting and

varnishing , lettering, numbering of all signalling gears, including signal posts and fittings, apparatus cases, point

machines, junction boxes, signal machine, rail post, other gears etc. complete at a station/mid section gates/huts,

letter writing on terminal Nos. apparatus cases, point machine, Signal Nos. and other details as per S.E.M.,

instructions of Engineer at site inspection by Consignee

113 CI 113 2.00 Set 1800.00 3600.00 AT Par 3600.00

Item Description:- Supply of Hammer dies for TLJB Cable/ connection. (Inspection by Consignee)

114

CI 114 2.00 Numbers 339820.42 679640.84 AT Par 679640.84

Item Description:- Supply of Precision pipe and cable locator consisting of MRT transmitter and signal lamp of

MXL stanlay make or similar. (Inspection by Consignee) Note- Prior approval of Railway to be taken before supply.

Demonstration/Training to be given at concerned SSE/Depot. Payment will be made only after

demonstration/Training

115

CI 115 2.00 Numbers 75500.00 151000.00 AT Par 151000.00

Item Description:- Supply of Digital Earth Resistance Tester. Model Motwane : DECT3) or similar of other

reputed make..(Inspection by Consignee) Note- Prior approval of Railway to be taken before supply.



116

CI 116 4.00 Numbers 86100.00 344400.00 AT Par 344400.00

Item Description:- Supply of AC/DC Leakage Clamp Meter. (Model Fluke-360) or similar of other reputed make

(with similar specifications). (Inspection by Consignee) Note- Prior approval of Railway to be taken before supply.



117

CI 117 8.00 Numbers 10410.00 83280.00 AT Par 83280.00

Item Description:- Supply of 53 Pcs Tele communication tool kit, for technician ( Model ST-TCK) or similar of

reputed make (Inspection by Consignee) (Annexure - 14)

118

CI 118 2.00 Set 81753.24 163506.48 AT Par 163506.48

Item Description:- Supply of standard Tool kits for PI/CLS as per the technical specifications and details.

(Inspection by Consignee) (Annexure -15 ) Note- Prior approval of Railway to be taken before supply.



119

CI 119 2.00 Set 206357.92 412715.84 AT Par 412715.84

Item Description:- Supply of cable fault locator in the underground cable as per model no. TFL-B5 of M/s APLAB

stanlay or similar branded make. (Inspection by Consignee). Note- Prior approval of Railway to be taken before

supply. Demonstration/Training to be given at concerned SSE/Depot. Payment will be made only after


120

Please see Item Breakup for details. 25248000.00 AT Par 25248000.00

Item Description:- Provision of MIS for signaling gears and its networking. (09 Stations in Agra Division)


121

CI 121 2.00 Pair 990429.83 1980859.66 AT Par 1980859.66

Item Description:- Supply, Installation, Testing & Commissioning of Block Proving of Digital Axel Counter as per

IRS spec No. IRS:S-105/2012 (Ver 0) or latest amendment using UFSBI and block panel for single line with

following materials (Inspection by RDSO). (a) Universal Fail-Sail Safe Block Interface (UFSBI) as per RDSO Spec

No. RDSO/SPN/147/2005 with latest amendment if any. (b) SM Panel as per RDSO Drg. No. RDSO/S/32019

(Tentative) or latest. (c) Relay racks with due locking and sealing arrangement wiring diagram as per RDSO Drg.

No. RDSO/S/32019 (Tentative) (d) Block telephone as per RDSO Spec No. RDSO/SPN/191/2006 with latest

amendment if any. (e) Relays for single line section as listed below will be supplied with prewired relay racks-62

Nos. i- Relays Non AC immunized plug in type style "QN1", DC neutral line 24V, 12F/4B or 8F/8B metal to carbon

along with plug board, retaining clips and connectors confirming to BRS: 930, IRS:S23 (As applicable). The

interlocking code for this unit shall be ABCDE-44 Nos. ii- Relays AC immunized plug in type style "QNA1", DC

neutral line 24V, 12F/4B or 8F/8B metal to carban along with plug board, retaining clips and connectors confirming

to BRS: 931A, IRS:S23 (As applicable). The interlocking code for this unit shall be ABCDE-12 Nos. iii- Relays plug

in type style "QL1", magnetically latched, neutral line 24V, 11F/4B or 8F/8B metal to carbon along with plug board,

retaining clips and connectors confirming to BRS: 935A, IRS:S24 (As applicable). The interlocking code for this unit

shall be ABDEG-04 Nos. iv- Relays fail safe electronic time delay device mounted on "Q" series relay base &

covered with fixed time of 120 seconds confirming to IRS: 61-2000, IRS:S34 (As applicable). The interlocking code

for this unit shall be AFGKY-02 Nos. v- User manual with each pair of set. vi- All the items mentioned above are to

be installed and interfaced with the existing BPAC equipment as per standers RDSO approved arrangement/as

directed by Engineer in charge at site. (f) Wooden rack/counter made of good quality for fixing block panel. (g)

This will also include supply of automatic media change over modems working on OFC/Quad= 1pair OR SSBPAC

(Digital)for single line as per spec no . RDSO/SPN/175/2005 Ver1 with all accessories.

CI 122 16.00 Numbers 118899.00 1902384.00 AT Par 1902384.00


TENDER DOCUMENT


of 33 Run Date/Time: 07/02 /2019 14:45 :34

S.No. Item

Code


Bidding

Unit

Schedule c-Part-II (Execution items) Above/

Below/Par

01

C II 01 4.00 Numbers 2432.70 9730.80 AT Par 9730.80

Item Description:- Installation, Wiring, Testing and commissioning of Isolation Transformer 10 KVA, Input and

output 230 V AC 50 Hz Sine Wave Single Phase, as per technical specifications

02

C II 02 2.00 Station 526820.00 1053640.00 AT Par 1053640.00

Item Description:- Supply & installation of fire detection & alarm system (air aspiration) as per RDSO-Draft

specification no RDSO/SPN/New /2010. (Inspection by RITES) (It covers complete building)

03

C II 03 5312.00 Each 109.68 582620.16 AT Par 582620.16

Item Description:- Installation, Wiring & Commissioning of the signaling Circuit Automatic Fuse changeover

Module for 2-6 Amperes with standby fuse for 12V/24V/60V DC or 110V AC complete unit for various signaling

functions in location boxes all with contractor's materials.

04


Item Description:- Installation, Wiring, Testing and commissioning of Power Supply Measurement, Display &

Alarm System with SMS Facility including design and fabrication and accessories as per site requirement and as

per technical specifications, required cable will be given by Railways.

05


Item Description:- Supply & fixing of hylam sheet 10 mm thick, of minimum grade P3, (size 860 mm X 140 mm

)on apparatus case/Location boxes for wiring of signaling circuits and cable termination, fixing on suitable size

contractor's angle with string rod for supporting cable on back side, including fixing of all types of terminals/ fuses

as per location diagram/plan and technical specifications, with drilling of holes on either sides of terminals/ fuses

and other places as required for cable conductor / wires entry and fixing of sheet. (Inspection by Consignee)

06


Item Description:- Supply & fixing of hylam sheet 10 mm thick, of minimum grade P3, (size 860 mm X 100 mm

)on apparatus case/Location boxes for wiring of signaling circuits and cable termination, fixing on suitable size

contractor's angle with string rod for supporting cable on back side, including fixing of all types of terminals/ fuses

as per location diagram/plan and technical specifications, with drilling of holes on either sides of terminals/ fuses

and other places as required for cable conductor / wires entry and fixing of sheet. (Inspection by Consignee)

07


Item Description:- Fabrication & fixing of hylam sheet 10 mm thick, of minimum grade P3, on apparatus

case/Location boxes single for wiring of signaling circuits and cable termination, fixing on suitable size contractor's

angle with string rod for supporting cable on back side, including fixing of all types of terminals/ fuses as per

location diagram/plan and technical specifications, with drilling of holes on either sides of terminals/ fuses and

other places as required for cable conductor / wires entry and fixing of sheet.

08


Item Description:- Excavation, ramming, Casting Cement Concrete foundation for full Apparatus cases/Location

boxes in the ratio of 1:3:6 Aggregate not exceeding 3 : 8 cm, as per Drg. No. SK 748 and technical specifications

using standard size galvanized Anchor bolts & nuts (also referred to as foundation bolts) conforming to IRS Drg.

No. SA-116A/M, for erection of Apparatus cases/Location boxes, plastering with 1 : 4 cement - sand mixture all

the surfaces up to 75 mm below ground level, complete with contractor's material including cement, sand, stones,

anchor bolts and nuts and curing of casted foundation, refilling & ramming of loose soil around foundation and

disposal of loose dugged soil from site. (Post SS/ Full Location Box)

09


Item Description:- Excavation, ramming, Casting Cement Concrete foundation for Half Apparatus cases/Location

boxes in the ratio of 1:3:6 Aggregate not exceeding 3 : 8 cm, as per Drg. No. SK 747 and technical specifications

using standard size galvanized Anchor bolts & nuts (also referred to as foundation bolts) conforming to IRS Drg.

No. SA-116A/M, for erection of Apparatus cases/Location boxes, plastering with 1 : 4 cement - sand mixture all

the surfaces up to 75 mm below ground level, complete with contractor's material including cement, sand, stones,


disposal of loose dugged soil from site. (Meduim Box Type SS/Half Location Box)

10


Item Description:- Installation of Apparataus cases/Location Boxes on CC foundation on grouted bolts, including

filling the space enclosed below the location box with contractor's sand, as per technical specifications. (Post SS

Location Box as per Drg. No. SK 748)

122 Item Description:- Supply, installation of Air conditioner. Make - HITACHI, RAG048HTD3, 4 Ton Split AC or

similar other reputed make ( for other make prior approval from Rly Engg. Is required before supply). (Inspection

by Consignee)


TENDER DOCUMENT


of 33 Run Date/Time: 07/02 /2019 14:45 :34

11


Item Description:- Installation of Apparatus cases/Location Boxes on CC foundation on grouted bolts, including

filling the space enclosed below the location box with contractor's sand, as per technical specifications. ( Meduim

Box Type SS Location Box as per Drg. No. SK 747)

12


Item Description:- Fixing of ARA Terminals and fuse blocks with provision of holes on hylem sheets and fixing by

galvanized nuts & bolts. This includes provision of two additional holes on the hylem board on either side for cable

conductor entry. The work shall be done as per the instruction of Rly. Engineer at site.

13


Item Description:- Termination of cables and supporting of string rod, with supply and providing identification

tags/ferrules/tapes with letters on each cable conductor. As per instruction of site in charge. (Full case)

14


Item Description:- Termination of cables and supportling of string rod, with supply and providing identification

tags/ferrules/tapes with letters on each cable conductor As per instruction of site in charge. (Half case)

15

C II 15 12900.00 Per

Conductor 9.46 122034.00 AT Par 122034.00

Item Description:- Termination of cable cores on disconnecting links /ARA terminals, fuse blocks etc. in the

apparatus cases, provided on the cable termination rack. This includes all associated works like pulling in/out the

cable from underground, peeling of insulation, dressing of cable cores supported on insulating galvanized & PVC

coated M.S. string rods. (All dressing and insulating material including string rods are to be supplied by

contractor).

16


Item Description:- Installation, fixing of (Relays, resistance chargers, bulb holders & accessories etc) & wiring of

the same in apparatus cases as per location diagrams with contractor's own wiring material suitable for 25 KV

area. This also includes supply & installation of Three pole switch & socket 5A (Anchor make)and Lamp holders,

two pin, Bakelite type fixing arrangement at contractor own cost. The work shall be done as per instruction of

Railway engineer at site. Apparatus case (Full)

17


Item Description:- Installation, fixing of (Relays, resistance chargers, bulb holders & accessories etc) & wiring of

the same in apparatus cases as per location diagrams with contractor's own wiring material suitable for 25 KV

area. This also includes supply & installation of Three pole switch & socket 5A (Anchor make)and Lamp holders,

two pin, Bakelite type fixing arrangement at contractor own cost. The work shall be done as per instruction of

Railway engineer at site. Apparatus case (Half Case)

18 C II 18 210.00 Numbers 699.30 146853.00 AT Par 146853.00

Item Description:- Supply and fixing of 2 stroke godown lock .

19

C II 19 28.00 Turn-out 3923.49 109857.72 AT Par 109857.72

Item Description:- Removal of existing electro mechanical point fittings and point machine from insulated points,

Fixing of Electrical Point Machine on the extended sleepers at points as per std. Practice with contractor's long

fixing bolts, buts and as per RDSO Drg No. SA 9151-52 or 9710 or 9161 as per section of rails used, wiring inside

the point machine with contractor's wiring material, supply and fixing of GI pipes (Gland pipe) with flange for taking

cable into point machine, termination of tail cable in point machine and junction boxes, the complete work of

Electric point machine installation as per Technical specifications,, removal of ground connections, point machines

after testing (duly numbered) and re-fixing of mechanical point fittings. Including servicing of point machine and

supply and filling of SAE-30 lubricating oil (500 ml approx.) per machine, supply of all fixing material, necessary

fittings and adjustment to make the mechanically operated points functional again. (Ordinary lay out /Derail

switch/Double slip/Single slip lay out) and alteration in ground connection to install point machine on raised plate

form in water logging area Derail switch/Double slip/Single slip lay out ) and alteration in ground connection to

install point machine on raised plate form in water logging area.

20

C II 20 48.00 Turn-out 10737.13 515382.24 AT Par 515382.24

Item Description:- Fixing of complete set of ground connections as per RDSO Drg No. SA 9151-52 or 9710 or

9161 as per section of rails used including D/P brackets, drilling of required holes in tongue rails & brackets for

fixing various rods etc., fixing of various insulations, adjusting opening of the switches and adjusting the point

machine with crank handle including all smithy & fitting works required at site for complete installation and fitting

insulation for gauge tie plate & William Stretcher Bar etc., the complete work of ground connections & insulation by

contractor also oiling and greasing of point machine and filling of SAE-30 lubricating oil ( 500 ml approx per

machine ) and fixing materials including nut bolts to be supplied by contractor.

21



TENDER DOCUMENT


of 33 Run Date/Time: 07/02 /2019 14:45 :34

Item Description:- Charging of Secondary cells with Contractor's own charging equipments including supply of

Sulphuric acid conforming to IS:266-1977, distilled water conforming to IS:1069-1964,installation Supply and

application of acid proof foam activities as per Technical specifications and according to standard adopted for

initial charging and installation of charged batteries spray of approved type, on the terminals of charges batteries,

all in battery room in groups as per instructions of Engineer at site.(2Volt, 80 AH)

22


Item Description:- Supply, Installation, fixing and wiring of Alarm unit for Track Feed battery charger of RDSO

Spec No.: IRS:S-89-93 with Amendment-3, from RDSO approved source of charger, to work on 110 V AC, having

terminals for connecting all 3 supplies and indications for mains and charger failure and drive potential free

contact all with contractor's material, all as per technical specifications.( per track)(Inspection by Consignee)

23


Item Description:- Installation commissioning & testing of MSDAC(6 track section 8 detection point) IT includes

Installation, wiring, testing & commissioning of of track device (double rail contact) of MSDAC, including digging of

trench, track crossing, laying of double walled antirodent corrugated pipe from track side to location box and

making its terminations, fixing of deflector plates.(all other accessories as per site requirement to be supplied by

the firm) and including Installation, wiring, testing & commissioning of central evaluator, wiring from the CT rack to

the central evaluator and wiring of the Reset boxes and wiring of the power supply to the evaluator including

supply of cable/shielded cable of required conductor size as applicable with all accessories 10/16Sqmm PVC wire

from equipment room to Central Evaluator will be born by contractor. This also includes the painting & wiring work

on the evaluator as per site requirement.

24

C II 24 160.00 Set 4612.50 738000.00 AT Par 738000.00

Item Description:- Installation of Axle Counter Cable conductor's Earth Resistance Sensing Unit, Microcontroller

based for 12 no's conductors without cable (Cable by Railway)

25

C II 25 80.00 Per Track

Circuit 9078.27 726261.60 AT Par 726261.60

Item Description:- Installation and commissioning of DC track circuits including drilling of bond holes, supply and

fixing of continuity GI wire bonds on rail joints after drilling bond-hole of 7.0/7.2mm dia. wherever required, bond

clips, channel pin & making rail connections of lead wires, installation & fixing of track lead junction box on MS

angle grouted on concrete and cable taken through DWC Pipe for track feed end, track relay end and BX

Jumpers, connections to tail cable, termination of tail cables on TLJB terminals etc., insertion of insulated block

joints and also fixing jumper cables as per insulation diagram/track bonding plan, charging & adjustment of track

circuit, all activities as per standard practice and technical specifications. This also includes Installation, fixing and

wiring of DC track circuits equipments, track battery charger, resistances/chokes, track relays and batteries etc., in

apparatus cases, location huts, relay rooms etc., with contractor's wiring material, termination of tail cables. T.C.

not involving pt. zone

26

C II 26 44.00 Per Track

Circuit 9684.00 426096.00 AT Par 426096.00

Item Description:- Installation and commissioning of DC track circuits including drilling of bond holes, supply and

fixing of continuity GI wire bonds on rail joints after drilling bond-hole of 7.0/7.2mm dia. wherever required, bond

clips, channel pin & making rail connections of lead wires, installation & fixing of track lead junction box on MS

angle grouted on concrete and cable taken through DWC Pipe for track feed end, track relay end and BX

Jumpers, connections to tail cable, termination of tail cables on TLJB terminals etc., insertion of insulated block

joints and also fixing jumper cables as per insulation diagram/track bonding plan, charging & adjustment of track

circuit, all activities as per standard practice and technical specifications. This also includes Installation, fixing and

wiring of DC track circuits equipments, track battery charger, resistances/chokes, track relays and batteries etc., in

apparatus cases, location huts, relay rooms etc., with contractor's wiring material, termination of tail cables. Pt.

zone T.C.

27


Item Description:- Excavation, ramming, Casting Concrete foundation for Colour Light Main Signal Post in the

ratio of 1:3:6, Aggregate not exceeding 3 : 8 cm, as per Drg.No.SK-749 based on Drg No RST 11173 using

standard size galvanized Anchor bolts & nuts (also referred to as foundation bolts) conforming to IRS Drg. No. SA-

116A/M, for erection of colour light signal post, plastering with 1 : 4 cement - sand mixture all the surfaces up to

75 mm below ground level, complete with contractor's material including cement, sand, aggregate, anchor bolts

and nuts and curing of casted foundation, refilling & ramming of loose soil around foundation and disposal of loose

dugged soil from site.

28


Item Description:- Casting, concreting and curing of foundations for shunt signal as per drg. No. Sig. / RRI / 30 -

87. All material such as cement, sand, aggregate & foundation bolts will be supplied by contractor.

29


Item Description:- Assembling, erection, installation & taking of cable inside unit through post, termination and

wiring of CLS complete with all accessories of CLS unit, post, base, ladder, ladder guards, platform and MS

supporting bracket in the middle of the ladder, hoods, pinnacles, offset brackets, etc. including fixing & wiring of

LED units lamps with contractor's wiring material with A/AG /calling ON signals complete with all fittings.


TENDER DOCUMENT


of 33 Run Date/Time: 07/02 /2019 14:45 :34

30


Item Description:- Erection of shunt signal with Surface base, post, signal unit and fixing of No. plates. The work

shall be done as per instructions of Railway Engineer at site.

31


Item Description:- Fixing of Jn. Route Indication 1-Way/2-Way/3-Way/theatre type on the top of the signal post

as per instructions of Railway Engineer at site.

32

C II 32 29000.00 Metre 46.20 1339800.00 AT Par 1339800.00

Item Description:- Digging of 1.20 Meter deep and 0.3 Meter wide trenches including clearing of roots of trees

and bushes and temporary obstruction on the selected route, as per technical specifications and cable route plan.

Note:In case where digging of trench up to 1.20 Meter depth and 0.3 meter wide is not possible or bigger size

trench is required to lay more cables or loose soil/ muck is encountered, the depth can be reduced / increased as

per directions of the Engineer-in-charge of the works, the payment will be decreased/increased proportionate to

the depth & width of excavation compared to 1.20 Meter deep and 0.3 Meter wide. This also includes Back filling

and consolidating of cable trench first for 5 CM (in case where bricks are to laid over cables) after laying of cables

and then complete back filling & Ramming of loose soil as per the technical specifications. (In all type of soils

including soft rock)

33

C II 33 1250.00 Metre 66.72 83400.00 AT Par 83400.00

Item Description:- Digging of 1.20 Meter deep and 0.3 Meter wide trenches including clearing of roots of trees

and bushes and temporary obstruction on the selected route, as per technical specifications and cable route plan.

Note: In case where digging of trench up to 1.20 Meter depth and 0.3 meter wide is not possible or bigger size

trench is required to lay more cables or loose soil/ muck is encountered, the depth can be reduced / increased as

per directions of the Engineer-in-charge of the works, the payment will be decreased/increased proportionate to

the depth & width of excavation compared to 1.20 Meter deep and 0.3 Meter wide. This also includes Back filling

and consolidating of cable trench first for 5 CM (in case where bricks are to laid over cables) after laying of cables

and then complete back filling & Ramming of loose soil as per the technical specifications. (In rocky soils)

34

C II 34 200.00 Metre 128.19 25638.00 AT Par 25638.00

Item Description:- Excavation of trenches 300mm wide 300mm deep on concrete/mettled/ macadamized/ stone

paved road or on platform, laying of DWC pipe All mm dia 6 mtrs long with collars provision of 2 wires in the pipe

for pulling the cable and refilling the trench, repairing the excavated area to its original condition and disposal of

extra soil.

35

C II 35 4000.00 Metre 738.06 2952240.00 AT Par 2952240.00

Item Description:- Trenchless trenching for Track Crossing & Road Crossing for laying various dia, DWC (Double

Walled Corrugated) pipes. Depth of trenchless Trenching shall not be less than 1.5 mtrs. The work shall be done

as per extant practice on N C Rly and as per instructions of Rly representative at site.

36

C II 36 533.00 Kilometre 4170.00 2222610.00 AT Par 2222610.00

Item Description:- Laying of S&T Cables of various cores/pairs/quads in trenches/GI pipes/RCC/ DWC

pipes/trunking with laying of these including laying of cables in track crossings & road crossings, provision of labels

on each cable of colored plastic adhesive tapes or any other identifiable marker complete with contractor's

material to give the cable number at each termination point and meggering of all Cables before and after its laying

before termination by contractor under supervision of Railway Representative and submitting the maggering

report of each testing, the complete activities to be done as instruction of site in charge Note:Length of the cable

laid includes the length of the cable coiled for termination purposes.

37

C II 37 400.00 Metre 701.00 280400.00 AT Par 280400.00

Item Description:- Fixing of GI pipes/DWC pipes of all sizes & diameters/ toughing on culverts, bridges & any

other loc. etc. complete with contractor's material including clamps, nuts and bolts and other fixing arrangements

as directed by Engineer in charge.

38

C II 38 4500.00 Metre 6.58 29610.00 AT Par 29610.00

Item Description:- Laying of DWC pipes various dia along with collars at places of track, road crossing platform

cutting etc or as directed by Railway representative at site.


Item Description:- Jointing of all type Signalling & Telecom cables.

40

C II 40 4.00 Set 51163.00 204652.00 AT Par 204652.00

Item Description:- Installation, testing and commissioning of electrically lifting barrier, complete with casting of

cement concrete foundation for pedestal and boom rest post as per standard drawing , cabling power supply

connection & wiring with complete outdoor work including earthing of barriers. This includes Wiring of Electrical

lifting barrier set complete with boom locking & panel including wiring of electrical contact/controllers and group

phone/master slave unit with contractor's material, Hooter assembly including termination of concerned cables at

gate.



TENDER DOCUMENT


of 33 Run Date/Time: 07/02 /2019 14:45 :34

41

Item Description:- Excavation, ramming, Casting Concrete foundation for Colour Light Main Signal Post(for road

signanl) in the ratio of 1:3:6, Aggregate not exceeding 3 : 8 cm, as per Drg.No.SK-749 based on Drg No RST

11173 using standard size galvanized Anchor bolts & nuts (also referred to as foundation bolts) conforming to IRS

Drg. No. SA-116A/M, for erection of colour light signal post, plastering with 1 : 4 cement - sand mixture all the

surfaces up to 75 mm below ground level, complete with contractor's material including cement, sand, aggregate,


disposal of loose dugged soil from site.

42


Item Description:- Assembling, erection, installation & taking of cable inside unit through post, termination and

wiring of CLS complete with all accessories of CLS unit, post, base, ladder, ladder guards, platform and MS

supporting bracket in the middle of the ladder, hoods, pinnacles, offset brackets, etc. including fixing & wiring of

LED units lamps with contractor's wiring material. (Road Signal)

43

C II 43 40.00 Job 2784.90 111396.00 AT Par 111396.00

Item Description:- Casting of concrete foundation 2'x2'x3' with cement concrete, sand of ratio 1:3:6 (Sliding

Boom)

44

C II 44 4.00 Job 6851.10 27404.40 AT Par 27404.40

Item Description:- Installation, testing, wiring & commissioning and Painting of sliding boom.(including fixing

relay/ARA/8way terminal, termination of cable etc. as per direction of site in charge.

45

C II 45 4.00 Lot 6350.55 25402.20 AT Par 25402.20

Item Description:- Preparation of cable route plan, cable corage plan, location diagram & particulars, CT rack

particulars and cable termination diagram, meggering report, earth resistance particulars, traction bonding

diagram/track insulation & bonding diagram & any other drawing/particulars required for PI/EI as per the technical

specifications applicable for circuit designing.

46

C II 46 4.00 Job 7324.86 29299.44 AT Par 29299.44

Item Description:- Alteration to existing circuit setting of additional circuits as per approved diagram as soldering

including fuse as function wiring , wiring of operating cum indication panel. Axle counter, evaluator. Per

equipment, IPS By, KLR box and their inter connection etc. fixing of dominos and their wiring to suit modified lay

out. (LC gate/ Auto)

47


Item Description:- Fixing of Q series relay base plates, laying, lacing, dressing and packeting of PVC indoor

cable/flexible wire and termination of conductors of indoor cable/flexible wire on tag blocks/base plates and

soldering. Wiring of circuits is to be done as per approved diagram based on Electronic Interlocking system using

metal to carbon type relays and soldering. This also includes fuse wiring, function wiring (interconnection between

relay racks & CT racks) and supply of materials like solder, resine core, lacing threads, adhesive tapes etc. The

work shall be done as per approved plan, extant practice and the instructions of railway engineer at site. (Item QtY

Unit - PER RACK)

48


Item Description:- Painting (Single Case) two coats of enamel paint over one coat of Red Oxide primer on the

following items after scraping and cleaning of the surface wherever necessary. Primer and paints both Asian

paints are to be supplied by contractor. Location boxes inside & outside surfaces with aluminum paint.


Item Description:- Lettering, Numbering, termination particulars, equipment name etc legibly & neatly (TLJB) etc

50


Item Description:- Lettering, Numbering, termination particulars, equipment name etc legibly & neatly in location

boxes etc

51

C II 51 98.00 Set 7757.00 760186.00 AT Par 760186.00

Item Description:- Installation of complete Earthing and Bonding system as per code of practice

RDSO/SPN/197/2008 or latest ,to construct earthing of </=1 Ohm including auguring hole of 100-125 mm dia and

minimum 2.8 meter depth for earth electrode carrying out necessary digging work and to make , 300x300x300

mm ( inside dimensions ) concrete box with lid if approx , 50 mm thickness and painted black on top , all with

contractor's material , fixing earth electrode in the augured hole ,filling Earthing enhancement material around

earth electrode in the hole in slurry form and allowing to set , back filling of excavated soil after sieving ,

measurement of earth value and all other work of earthing as per code of practice

52


Item Description:- Supply & Installation of distilled water plant including supply of 500 Ltr overhead hard PVC

watter storage tank, its installation on supporting structure and supply, laying pipe and making connection

between storage tank and distil water plant (capacity 65 litres per hour approx). This includes all the pipe

connection from water source to unit and also to collection unit. As per instruction of site in charge. (Inspection by

consignee)

53



TENDER DOCUMENT


of 33 Run Date/Time: 07/02 /2019 14:45 :34

Item Description:- Supply of Office table having laminated top godrej make or similar. (Inspection by consignee)

54


Item Description:- Supply of U-plain storage Elmira with 4-adjustable shelf of Godrej make or similar. (Inspection

by consignee)


Item Description:- Supply of Chair of Godrej make (Inspection by consignee)


Item Description:- Supply of Minor plan storage Elmira Godrej make or similar. (Inspection by consignee)


Item Description:- Supply of Steel stool of Godrej make or similar. (Inspection by consignee)

58


Item Description:- Supply & installation of Ultra sonic Rat repellant for relay room/IPS room model no Trio-123 or

similar specifications (Annexure-19 ) (Inspection by Consignee)

59


Item Description:- Supply & installation of Water purifier make Kent Genpure/Aqua Guard or similar (Cap. 9 Ltr)

total RO water filter cum purifier with AMC for one year or equivalent. (Inspection by consignee)


Item Description:- Supply, installation of glass fronted key box. (Inspection by consignee)

61


Item Description:- Supply of rechargeable remote area lighting system USA make pelican model 9430 RALS or

similar. (Inspection by consignee)


Item Description:- Supply industrial vacuum cleaner. (Inspection by consignee)

63


Item Description:- Fabrication, supply, installation & fixing of SWRD / cabin diagram on board of size

1500mmx700mm made of 12mm ply word of approved type and size as per requirement. (Inspection by

consignee)

64

C II 64 30.00 cum 2138.15 64144.50 AT Par 64144.50

Item Description:- Cement concrete work for miscellaneous items in the ratio 1 : 3 : 6, aggregate not exceeding

3 : 8 cm including excavation,raming, curing and plastering with 1 : 4 cement - sand mixture complete with

contractor's material including cement, sand, aggregate and curing of casted foundation, refilling & ramming of

loose soil around foundation and disposal of loose dugged soil from site. NOTE: Due to local condition in very

special circumstances if the size of the foundation for all the above items is required to be increased / decreased,

the extra payment /deduction for variation of the CC work shall be calculated on volumetric basis as per rate of

this item.

65


Item Description:- Preparation of cable route plan, cable corage plan, location diagram & particulars, CT rack

particulars and cable termination diagram, meggering report, earth resistance particulars, traction bonding

diagram/track insulation & bonding diagram , SWR & any other drawing/particulars required for PI/EI as per the

technical specifications applicable for circuit designing.

66


Item Description:- Releasing of lever frame, old location boxes, LC Gate, signal posts,TLJB, equipments in site

the location boxes and all fitting etc.

67

C II 67 24.00 Month 63366.80 1520803.20 AT Par 1520803.20

Item Description:- Hiring of 02 Nos of vehicle for supervision of execution of work done at site - Non-AC Tata

Sumo / Bulero / Xylo/Tata MOVUS or similar Make not be more than Three (3 ) Years old & in good working

condition, including Driver, Fuel, Crew and Maintenance etc., for running of 2500 Kms per month. (Nature of work:

24 Hrs per day without any Holiday/Rest. for 24 Months)" (Rate of Two vehicle per month = Per Vehicle per month

rate 31,683.40 x 2 = 63366.80 ) Note- Prior approval of Railway to be taken before supply.

68


Item Description:- Loading and transportation of signalling & telecom materials to/from SSE/Sig/Store at AGC to

other station & other station to AGC (Scrap yard) or other divisional units including lead, lift ascent, descent and

measurement for the purpose shall be Railway track kilometre.(9 MT vehicale)

69


Item Description:- Transportation of less heavy materials & manpower supply & running of one MUV to the sites

of work as per requirement and direction of Engineer in-charge along with Driver. The rates includes all taxes

license fee, road permit, driver wages, fuel, repair and maintenance cost of etc complete in all respects


TENDER DOCUMENT


of 33 Run Date/Time: 07/02 /2019 14:45 :34

70 Please see Item Breakup for details. 4098092.00 AT Par 4098092.00

Item Description:- Augmentation of store depot/ office accommodation.

S.No. Item

Code


Bidding

Unit

Schedule d-Telecom Above/

Below/Par

01

D 01 100.00 Metre 781.78 78178.00 AT Par 78178.00

Item Description:- Supply & Fixing of GI pipe with thread collars of 100 mm nominal bore, specn. No IS 1239

medium grade, to be perforated after supply for required length , as per technical spech.(Inspection by

Consignee)

02

D 02 10.00 Numbers 1018.27 10182.70 AT Par 10182.70

Item Description:- Supply and installation of CT box with GD tubes & LD etc with disconnection facility &

termination of cables as per RDSO guidelines(Inspection by Consignee) 10 pair

03

D 03 10.00 Numbers 2036.55 20365.50 AT Par 20365.50



04

D 04 10.00 Numbers 5259.05 52590.50 AT Par 52590.50



05

D 05 2.00 Station 2529.75 5059.50 AT Par 5059.50

Item Description:- Taking the all types of cables inside station relay rooms location boxes and junction boxes etc

and sealing of cable entry pit etc as per technical specifications, complete with contractor's material.(Inspection by

Consignee)

06

D 06 5.00 Numbers 570872.00 2854360.00 AT Par 2854360.00

Item Description:- Supply of STM 64/16 equipments along with interface cards (model TJ1600C/TJ1400) for

RailTel/NR.(Inspection by RDSO)

07

D 07 5.00 Numbers 81628.16 408140.80 AT Par 408140.80

Item Description:- Supply of Fiber distribution management system as per RDSO/specification No.

RDSO/SPN/TC-37-2000 (Ver.3) with latest amendment as on the date of opening of tender. (It include the supply

of 19" 42 rack with mounting arrangement as per Annexure No. 24 Rack will be consignee inspection (Inspection

by Consignee)

08

D 08 5.00 Numbers 125669.36 628346.80 AT Par 628346.80

Item Description:- Supply of 2 Mb programmable primary digital Drop Insert Mux with all interface cards,

connection to 48 V bus bar and termination of VF/Data interface circuits to the Krone MDF in already installed 42-

U Euro rack. This includes termination of PVC cable at both ends and taking PVC cable over runway or on the

wall. This also includes supply of PVC cable of conductor size 0.63mm. The MUX shall be equipped for 16 E&M

VF circuits, 4 data circuits of 64 kbps, 6 hot line,/subscriber interface circuits. The equipment shall be RDSO

approved on the date of opening of tender. The OFC equipments supplied in this work should be compatible with

the existing M/s Webfil make PD Mux system. As per IRS.TC.68.04 with latest amendment which are already

installed in Section & should be able to manage with the existing NMS of the section. The existing proposed

equipment should be as per IRS Specification TC.68.04 (Amendment-1) with latest amendments. However in

case this specification does not match with the existing system then RDSO spec. Will not be insisted upon as to

have seamless connectivity with existing equipments and NMS.(Inspection by RDSO)

09

D 09 5.00 Numbers 40871.86 204359.30 AT Par 204359.30

Item Description:- Supply of SMPS based 48 Volts, 25 Amps single phase 230 Volt AC operated FR-FC-BC

battery charger for telecom use as per specification No. RDSO/SPN/TL/23/2008 (Rev.4) with latest amendments

in N+2 configuration i.e. using 4 modules of 12.5 Amp with automatic switching between the module suitable for

200 AH MF VRLA battery bank. It shall be equipped with surge and lighting protection of class B&C along with

instruction and service manual. (Inspection by Consignee)

10

D 10 5.00 Numbers 50905.25 254526.25 AT Par 254526.25

Item Description:- Supply of Multi telephone way station equipment with necessary mounting arrangement on

standard 19" rack. It shall be 48 volt operated as per RDSO Draft specification No. RDSO/SPN/TC/66/2007 with

amendments 1 & 2 and subsequent amendments if any on the date of tender opening.(Inspection by Consignee)

11

D 11 10.00 Numbers 4174.07 41740.70 AT Par 41740.70

Item Description:- Supply of 24 fiber optic fiber cable straight joint enclosure (SJC) complete with all accessories

as per G/OJC-02/01 March 99 with latest amendment.(Inspection by Consignee)

D 12 20.00 Numbers 1111.73 22234.60 AT Par 22234.60


TENDER DOCUMENT


of 33 Run Date/Time: 07/02 /2019 14:45 :34

12 Item Description:- Supply of 1120:470 Ohms VF isolation transformer rack mounting type as per RDSO

specification IRS/TC/22/76 with latest amendment applicable on the date of opening of the tender. (Inspection by

Consignee)

13

D 13 20.00 Numbers 1111.73 22234.60 AT Par 22234.60

Item Description:- Supply of 600:470 Ohms VF isolation transformer rack mounting type as per RDSO

specification IRS/TC/22/76 with latest amendment applicable on the date of opening of the tender. (Inspection by

Consignee)

14

D 14 10.00 Numbers 1350.34 13503.40 AT Par 13503.40

Item Description:- Supply of Signaling Transformer 50 V/50 Hz Ratio 1:2 rack mounting type as per Specification

No. IRS/TC/22/76 with latest amendment applicable on the date of opening of the tender. (Inspection by

Consignee)

15

D 15 5.00 Numbers 29049.43 145247.15 AT Par 145247.15

Item Description:- Supply of composite rack of standard make (President, Comrack, Rittal or equivalent.)

covered with front transparent doors, to house, 2 SDH, 2 OPT, MUX/OLTES and 2 PDH MUX along with PDP,

DDF, cooling fans, MDF for 100 pairs with anti surge protection through fast acting fuses and GD tubes, IPM (Z

protection) (Inspection by Consignee)

16

D 16 10.00 Numbers 1379.23 13792.30 AT Par 13792.30

Item Description:- Supply of Anti static mats of size 1 mtr x 0.75 mtrs & 3mm thickness. (Inspection by

Consignee)

17

D 17 4.00 Numbers 38102.70 152410.80 AT Par 152410.80

Item Description:- Supply of 200 AH MF VRLA battery set. Nominal voltage of 48 volts, 200 AH at 10 hrs rate

fully charged complete with all accessories with two nos manual of instruction with each set as per RDSO specn

No. S-93-96(A) with latest amendment. (Inspection by RDSO)

18

D 18 5.00 Numbers 13399.61 66998.05 AT Par 66998.05

Item Description:- Supply of battery charger/Power supply unit (SMPS) 230 V AC/12V DC 10 Amp. As per

IRS:S:93/96(B)(Inspection by RDSO)

19

D 19 5.00 Numbers 11858.81 59294.05 AT Par 59294.05

Item Description:- Supply of 12 V-80AH lead acid maintenance free battery banks with suitable racks as per

IRS:S:93-96(A) amendment 1. (Inspection by RDSO)

20

D 20 20.00 Numbers 1841.47 36829.40 AT Par 36829.40

Item Description:- Supply of Desk type Electronic Magneto Telephone as per Specn. No. IRS/TC/79/2000

Amendment-2 or latest. (Inspection by Consignee)

21

D 21 5.00 Set 5663.51 28317.55 AT Par 28317.55

Item Description:- Supply of Surge Suppressor for all the 30 circuits derived from primary MUX's (Z protection

complete as per technical specifications and other stipulations of tender document. (Inspection by Consignee)

22

D 22 5.00 Numbers 15223.96 76119.80 AT Par 76119.80

Item Description:- Supply of PA AMPLIFIER model no. TZA-2000 Ahuja make or similar (120 watt with mike)

with all accessories(Inspection by Consignee)

23 D 23 5.00 Numbers 1363.18 6815.90 AT Par 6815.90

Item Description:- Supply of Microphone 56 XLR or Ahuja Make or similar.(Inspection by Consignee)

24

D 24 12.00 Numbers 1519.40 18232.80 AT Par 18232.80

Item Description:- Supply of Loud speaker (horn type) 25 Watt-UHC-25-XT Ahuja make or similar (Inspection by

Consignee)

25

D 25 5.00 Numbers 12138.08 60690.40 AT Par 60690.40

Item Description:- Supply of ultra isolation transformer 230/230-1.5 KVA with MOVR protection on either side to

provide X protection and supply of cross bar surge protection circuit for 48 volt DC side to provide Y protection.


26

D 26 5.00 Pair 22951.50 114757.50 AT Par 114757.50

Item Description:- Supply of 02 MBps line termination unit/Ethernal extenders 48 V DC operated required for

Comm. Channel as per specification mentioned in the Annexure-21 along with suitable connector to extend the

data on copper cable of dia 0.5mm/0.63 mm and CAT 5/6 cables (Inspection by Consignee)

27

D 27 5.00 Numbers 65563.18 327815.90 AT Par 327815.90

Item Description:- Supply of 2 LAN/2WAN port, 2 MBPS Router-48 V DC operated as per specification

mentioned in Annexure-22 mentioned in the tender document along with required connecting cables and

connector to connect the ethernal devices. (Inspection by Consignee)

28

D 28 5.00 Pair 32827.60 164138.00 AT Par 164138.00

Item Description:- Supply of 2.048 Mbps managed SHDSL modems as per specification mentioned in the

Annexure-23 along with suitable connector.(Inspection by Consignee)


TENDER DOCUMENT


of 33 Run Date/Time: 07/02 /2019 14:45 :34

29

D 29 5.00 Numbers 11275.66 56378.30 AT Par 56378.30

Item Description:- Supply of cable termination panel fitted with 32 way U link feed panel along with U link

complete with mounting arrangement of isolation transformer as per drawing No. SK/CSTE/c/97/26 fitted with 12

No. Of 32 way U link feed panel complete with U link. (Inspection by Consignee)

30

D 30 20.00 Numbers 331.70 6634.00 AT Par 6634.00

Item Description:- Supply of push button telephone suitable for connecting with way side equipment and the

system as per spec No. GR/TEL/02/04 Sept 2004 or latest amendment and from DOT/TEC approved firm.


31

D 31 10.00 Kilometre 68832.07 688320.70 AT Par 688320.70

Item Description:- Supply of HDPE pipe 40mm dia as per TEC specification no GR/CDS/08/02 Nov. .2004 with

all amendment. (Inspection by RITES)

32

D 32 20.00 Numbers 2660.02 53200.40 AT Par 53200.40

Item Description:- Supply of Thermo shrinkable straight through joint suitable for making straight

through/deviation joint without transformer in under ground 6 quad/jelly filled cables. RDSO Specification No.

RDSO/SPN/TC/77/2010 Rev-2 or latest amendment) with all accessories. (Inspection by RDSO)

33

D 33 5.00 Numbers 15995.00 79975.00 AT Par 79975.00

Item Description:- Supply of VHF 25 watt transceiver radio with accessories details in 1 DTMF mic. DC cable

mounting bracket operating manual 2.6.5 db gain GP antenna diamond model CP-22E or similar 3.30 Meters RG

213 co-axial cable with with connectors at both ends make- Kenwood TK-7360. (Inspection by Consignee)

34

D 34 20.00 Numbers 2219.86 44397.20 AT Par 44397.20

Item Description:- Supply of 2 wire DTMF type way station control equipment with Telephone as per RDSO spn.

No. IRS-TC 60/2007 2007 or latest. (Inspection by Consignee)

35

D 35 8.00 Numbers 2499.66 19997.28 AT Par 19997.28

Item Description:- Supply of power supply unit for way station equipment of 2 W control telephones along with

12 V 7AH sealed Maintenance free battery as per RDSO specification No. IRS/TC 72-97 (Amd.1) or latest.


36

D 36 4.00 Numbers 14940.41 59761.64 AT Par 59761.64

Item Description:- Installation, wiring & testing of SDH/STMs with all accessories, DDF with miniature 'U' link type

for 63 E1s, runway ladder etc in already installed 42-U Euro rack. This includes connecting all pig tails, optical

patch cords etc. To the SDH equipment. This also includes connecting the SDH with all interface cards to the 48 V

Bus including supply of wires and connectors, termination of all E1s on DDF. This includes all sundry material

required for installation.

37

D 37 4.00 Numbers 7317.73 29270.92 AT Par 29270.92

Item Description:- Installation & wiring of PD MUX with all interface cards connection to 48V bus bar and

termination of VF/Data interface circuits to the Krone MDF. This includes termination at both ends and taking PVC

cable over runway or on the wall. This also includes supply of PVC cable of conductor size 0.63 mm & 100 pair

krone type D.P Krone shall have both current & voltage protection arrangement.

38

D 38 10.00 Numbers 3768.54 37685.40 AT Par 37685.40

Item Description:- Installation & supply of cable termination box for 26 conductors 0.5-0.9 sqmm with screw type

terminals consisting of the following parts complete of phonix contact make or of wago connect well make. Fixing

to be done as per drawing No. WCR/Tele/04-06 and instruction of railway supervisor at site.2 nos. Protection

devices at LC gate (supplied under this schedule) shall be provided on the terminals where jelly filled cable

terminated.

39 D 39 2.00 Station 7149.74 14299.48 AT Par 14299.48

Item Description:- Testing and commissioning of STM equipments.

40

D 40 2.00 Station 46980.49 93960.98 AT Par 93960.98

Item Description:- Installation, testing & commissioning of All UTS related equipments as per direction of

engineer in charge. This also include configuration, programming and interfacing with existing UTS network at

road side station which are not in the list of the station enclosed for UTS connectivity. This also includes the cost

of all type of connecting cables and connectors required for connecting the various devices

41

D 41 15.00 Numbers 637.72 9565.80 AT Par 9565.80

Item Description:- Installation, testing and commissioning of 4 wire way station equipment with necessary

mounting arrangement on standard 19" rack. This item includes supply of all required material for installation such

as PVC casing/capping, fixing materials, 10/20 pair indoor PVC cable and wiring between way station equipment

and termination box & masonry work etc. The installation shall be done as per the instructions of Engineer-in-

charge.

D 42 4.00 Set 4060.65 16242.60 AT Par 16242.60


TENDER DOCUMENT


of 33 Run Date/Time: 07/02 /2019 14:45 :34

42 Item Description:- Installation, wiring & commissioning of battery charger, 48 volt battery set fully charged and

ultra isolation transformers at each station Note: The rate quoted shall be including the cost of DC bus bar of 48V

DC/Power wire etc. Connection of power supply to the equipments. All the wiring shall be done with the suitable

gauge of power wires through suitable casing/capping as per the instruction of Railway Engineer's instructions. All

the materials required for this item shall be supplied by the contractor. (1 set of 48V/200AH, 1 set 24V/80AH, 1 set

of 12V/80 AH)

43

D 43 10.00 Numbers 9938.16 99381.60 AT Par 99381.60

Item Description:- Splicing of 24 fiber optic fiber cable and making the splice joint with contractor's own splicing

machine and tools. Joint should be prepared in such a way that the top of the enclosure shall be at a depth of 1.2

Mtr. And the enclosure should be covered with soft soil and then bricks. Acceptance Test Procedure of NCR has

to be followed for testing. Continuity of the OFC Armour should not be maintained.

44

D 44 200.00 Metre 128.40 25680.00 AT Par 25680.00

Item Description:- Excavation of cable trench 1.2meter deep and 300 mm wide across the track, for track

crossing and refilling after laying of GI pipes. The work shall be done as per extant practice on N.C.Rly &

instruction of Rly. Engrs. At site. This includes the laying of GI pipe where desired dimensions of trenches could

not be achieved proportionate payment will be made as decided by Engineer-in-charge at site.

45

D 45 500.00 Metre 192.60 96300.00 AT Par 96300.00

Item Description:- Excavation of cable trench 1.2 mtrs deep and 300 mm wide across the existing platform, road

cutting and refilling of GI pipes. It include laying of GI pipes in trenches. The work shall be done as per extant

practice on N.C.Rly & instruction of Rly Engineers at site.

46

D 46 5000.00 Numbers 2.56 12800.00 AT Par 12800.00

Item Description:- Supply & placing of second class bricks of standard size 225 mm x 100 mm x 75 mm (approx)

across the trench over the bad of loos soil on already laid cable in case of change in dimensions proportional

payment on volumetric basis will be made.(Inspection by Consignee)

47

D 47 4.00 Numbers 3590.92 14363.68 AT Par 14363.68

Item Description:- Fixing & supply of Earth Electrode & earthing of armour of underground Quad/JF cable and

extending it to the earth electrode by the use of earth wire of GI 8 SWG size connected through GI lug at either

end and terminated in cable hut/LC gate /cabin etc. All material required shall be supplied by contractor and

provision of cement enclosure, including cement, charcoal salt & lugs etc. The earth resistance should not be

more than 10 (Ten) ohms. (Inspection by Consignee)

48

D 48 4.00 Numbers 60264.54 241058.16 AT Par 241058.16

Item Description:- Provision of earthing system for telecom installations as per Spec. No.

RDSO/SPN/TC/75/2008 with latest amendment. (Inspection by Consignee)

49

D 49 4.00 Numbers 1341.78 5367.12 AT Par 5367.12

Item Description:- Installation of Thermo-shrinkable jointing kits for making (a) straight through joints without

transformer for 6 quad jelly filled cable, (b) Derivation joint with/without transformer of 6-Quad jelly filled cable,

and (c) Straight Through joint without transformer for 10 Pair/20 Pair PIJF cables and construction of Brick

Chamber for protection of joints with contractor's all materials.

50

D 50 4.00 Numbers 7036.32 28145.28 AT Par 28145.28

Item Description:- Installation of cable termination panel rack, mounting of isolation transformers, termination of

under ground jelly filled cables on the screw type terminals, supply of wiring material and wiring of circuitry as per

direction of Engineer in-charge.

51

D 51 2.00 Station 1900.32 3800.64 AT Par 3800.64

Item Description:- Writing work of cable termination details of 6-quad, OFC,PIJF cables & equipments details at

OFC Room/Cable hut & Station Building and wherever necessary as per direction of Engineer in-charge.

52

D 52 2.00 Station 101.65 203.30 AT Par 203.30

Item Description:- Installation of Antistatic mats in Repeaters, OFC/cable huts and fixing of runway wires on OFC

way in OFC/cable huts as per instruction of Engineer in-charge.

53

D 53 2.00 Station 2894.35 5788.70 AT Par 5788.70

Item Description:- Installation and commissioning of VHF set (25 watts) at RLY station including masonry & black

smith work as per the instruction of Engineer-in-charge. Required GI pipe will be supplied by contractor in size of

50 mm dia & 1500 mm in length, 40 mm dia & 6 mtr in length.

54

D 54 2.00 Station 4027.48 8054.96 AT Par 8054.96

Item Description:- Installation of PA system at Railway station as per instruction of engineer-in-charge. Required

cable, equipment & amplifier will be supplied by Railway.

55


Item Description:- Blowing/drawing of OFC cable in the HDPE pipe duct and in protective works already

provided.



TENDER DOCUMENT


of 33 Run Date/Time: 07/02 /2019 14:45 :34

56 Item Description:- Laying of HDPE duct in the trenches , and in the protective woeks already provided incuding

in HDD portion and supplu, pullig of nylon rope through it at different places as per directions of engineer in

charge or site engineer.

57

D 57 4.00 Numbers 3219.63 12878.52 AT Par 12878.52

Item Description:- Installation, supply and wiring of surge protection devices (class D) for 48 V DC supply for

each pair of conductor as per specification and instruction of site engineer.(Inspection by Consignee)

58

D 58 10.00 Numbers 5259.05 52590.50 AT Par 52590.50

Item Description:- Supply & fixing of 50 pair Krone termination DP's duly fitted with disconnection type.


S.No. Item

Code


Bidding

Unit

Schedule e-TPWS {(Design, manufacture and supply of Line side Electronic Unit (LEU)

mainly consisting of Balises(Switchable ,Fixed and Infill), Junction boxes, Power supply with

suitable Power back up ,LEU, LEU cabinet as per RDSO specification No.

RDSO/SPN/182/2011 version2 or latest on the date of Tender opening as per Special

conditions of contract and Technical Specification enclosed in tender document. (Inspection

by RDSO)}

Above/

Below/Par

01

E 01 16.00 Numbers 312918.14 5006690.24 AT Par 5006690.24

Item Description:- Design, manufacture and supply of LEU Modules , should be compatible to existing system in

AGC Div. (Inspection by RDSO)

02 E 02 16.00 Numbers 123963.36 1983413.76 AT Par 1983413.76

Item Description:- Design, manufacture and supply of LEU Line side cabinet (Inspection by RDSO)

03 E 03 16.00 Numbers 13200.00 211200.00 AT Par 211200.00

Item Description:- Design, manufacture and supply of Power supply for LEU. (Inspection by RDSO)

04

E 04 16.00 Numbers 91471.00 1463536.00 AT Par 1463536.00

Item Description:- Design, Manufacture and supply of line side Eurobalise(s) along with connecting cables based

on signalling roll plan etc.(Fixed and switchable eurobalises as per requirement) (Inspection by RDSO)

05 E 05 16.00 Numbers 4719.00 75504.00 AT Par 75504.00

Item Description:- Supply of Junction boxes. ( Inspection by Consignee)

06

E 06 100.00 Numbers 5770.89 577089.00 AT Par 577089.00

Item Description:- Supply of relays universal plug in type for LED signal lamp (Q type ECRs) as per BRS941A

Spec STS/E/Relays/AC Lit LED signal / 09-2002 with latest amendment or Metal To Metal for 110 V AC LED

signal lamp as per SPN.No.STS/E/RELAYS/AC LIT LED SIGNAL/09-2002 No. IRS: S: 46 AS PER DRG A-RT-RG-

A-064 (Siemens make) with base as per site requirement. (Inspection by RDSO)

07

E 07 2.00 Numbers 66000.00 132000.00 AT Par 132000.00

Item Description:- Supply of portable testing equipment along with diagnostic software for maintenance of train

bome TPWS equipment for use in sheds. This includes supply of documentation for working instructions with each

portable testing equipment. (Inspection by Consignee)

08

E 08 4.00 Numbers 39600.00 158400.00 AT Par 158400.00

Item Description:- Supply hand hold maintenance tools for testing the line side equipment/balise. (Inspection by

Consignee)

09 E 09 16.00 Numbers 10000.00 160000.00 AT Par 160000.00

Item Description:- Installation of LEU Module with all accessories and Cabinet

10 E 10 16.00 Numbers 5000.00 80000.00 AT Par 80000.00

Item Description:- Installation of Euroballises based on signaling roll plan.

11

E 11 5.00 Man-Week 12886.63 64433.15 AT Par 64433.15

Item Description:- Training of Railway personal on Design, Installation, Testing, Commissioning and

Maintenance of TPWS system including supply of course Module.(Manufactures premises)

12

E 12 5.00 Man-Week 4476.59 22382.95 AT Par 22382.95

Item Description:- Training of Railway personal on Design, Installation, Testing, Commissioning and

Maintenance of TPWS system including supply of course Module.(Loco sheds/S&T Railway training institute &

place of work)

S.No. Item Code Item Qty Qty Unit Unit Rate Basic Value Escl.(%) Estimated Amount

Bidding Unit

Schedule f-Training centre Above/

Below/Par


TENDER DOCUMENT


of 33 Run Date/Time: 07/02 /2019 14:45 :34

01

Please see Item Breakup for details. 694674.06 AT Par 694674.06

Item Description:- Provision of TPWS {Design, manufacture and supply of Line side Electronic Unit (LEU) mainly

consisting of Balises(Switchable ,Fixed and Infill), Junction boxes,Power supply with suitable Power back up

,LEU, LEU cabinet as per RDSO specification No. RDSO/SPN/182/2011 version2 or latest on the date of Tender

opening as per Special conditions of contract and Technical Specification enclosed in tender document.

(Inspection by RDSO)}


Item Description:- AXLE COUNTERS


Item Description:- DATA LOGGER EQUIPMENTS


Item Description:- Provision for lifting barrier

3. ITEM BREAKUP

Schedule Schedule C-Part-I (Other Supply Items)

Item- 120 Provision of MIS for signaling gears and its networking. (09 Stations in Agra Division) (Inspection by Consignee)

S No. Item

No

Description of Item Unit Qty Rate Amount

1 1 Supply of Smart Station Network Maintenance System

including its Database: Windows based Application

software with its relevant patches and Database of SQL

Server / MS SQL / MYSQL or Oracle to be supplied with

the 1 server license and 9 station users for maintaining of

Stations assets. Server Application will be installed at

Server machine located at HQ and Station user can log-in

in the server machine by its user credentials and work in

the modules as per Annexure -16 Schedule-1 items

should be as per total scope of work given in FRS in

tender document at annexure-17 entails and work in the

following modules:

Numbers 36.00 480000.00 17280000.00

2 2 Supply of Desktop Client Machine at stations:

Specifications: Desktop 202 MT core I5 4TH GEN / 4GB

DDR3 RAM / 500 GB HDD / No DVD/ WIN 8.1 PRO DG

TO WIN 7 PRO with TFT and UPS with battery backup for

10 minutes.

Numbers 36.00 75000.00 2700000.00

3 3 Supply of GSM Modem of Standard Make like Wave com

or similar for SMS based message or alarm escalation.

Numbers 4.00 12000.00 48000.00

4 4 Supply of Android based Tab of 10" touch screen, having

at least 4GB system memory and total memory space of

16GB or better, features for having data connection using

3G/4Gand Wi-Fi and Bluetooth. Smart Tab must be

loaded with Gears Inspection module software for

maintenance purpose. Railway engineers shall able to

log-in the software and feed the maintenance data online

as per SMC form of gear maintenance.

Numbers 120.00 21000.00 2520000.00

5 5 Implementation Services as per total scope of work given

in FRS in tender document at Annexure-17. (Asset /

Gears position Survey, Creating objects of Gears / assets

into Software application, Object / gears Database

Creation for future use: Contractor shall do the survey,

collect data and feed the initial data into the software to

make it live application.

Numbers 36.00 75000.00 2700000.00

Total 25248000.00

Schedule Schedule c-Part-II (Execution items)

Item- 70 Augmentation of store depot/ office accommodation.

S No. Item

No



TENDER DOCUMENT


of 33 Run Date/Time: 07/02 /2019 14:45 :34

1 1 Overhead Multimedia wireless projector having mini.

luminus capacity of 4100 Lumens with two VGA input , Six

Picture Mode [Dynamic, Presentation, RGB, Cinema

User1, User2] Contrast ratio 3100:1, Keystone Correction

, XGA 1024x 768, HDMI, video input monitor output with

all suitable accessories and cables as following:- (a)VGA

cable approximate 10 meters with connector (b)Power

cable approximate 10 meters with power socket. ( c)

HDMI Power cable 10 meters for multimedia Projector


Numbers 1.00 88751.70 88751.70

2 2 Supply , installation testing and commissioning of

PLOTTER of A0 size of HP make or similar of reputed

make(As per annexure-20) (Inspection by Consignee)

Numbers 1.00 696000.00 696000.00

3 3 Supply , installation testing and commissioning of scanner

of Canon make model cano Scan LiDE700F or similar of

reputed make (Inspection by Consignee)

Numbers 4.00 11130.20 44520.80

4 4 Supply, Prefabricated Porta cabin of size-20'x20'x 9'

height in single slope/double slope. (Annexure -18 )


Numbers 1.00 470967.50 470967.50

5 5 Supply of slotted angle Racks 15"x36"x78", 4 level,20

gauge shelves and 14 gauge angles, rust free nut bolt.

Product dimensions approx 91.4x38.1x198.1 cm


Numbers 18.00 4894.00 88092.00

6 6 Compactor System is standard mounted on a mobile way

Creating Excellent storage , single face unit has depth of

455 mm , Double face movable filling Computer has a

total depth of 910 mm the height of each unit is 2080 mm

(Including Rail and understructure ) from Floor level after

Installation and with Including the drive I 1895 , 2805

,3715 mm two , three and four way systems Respectively.

Shelved are able to carry maximum load of 55 kgs. UDL,

(Make -maxx or similar make) (Inspection by Consignee)

Numbers 2.00 122880.00 245760.00

7 7 Supply of Railways e-DTR managment for Signal &

Telecom (S&T). e-DTR Management application for one

user with its required software and its patches. e-DTR

management System will have architecture to run on

Windows platform and MySQL / MS SQL Database. It

shall have one Admin User which will be used by either

Dy.CSTE or Sr DSTE and another log-in for user. User

and have view of ledgers of each User either through

Windows based application or Android based Mobile

application. Admin can create reports of ledgers in User

wise, materails wise and save in either in .xls format or

.pdf format for printout.Each User shall able to log-in to

the server from any machine either using Mozilla or

Chrome browser. User shall able to create Vendor

information. It shall have e-DTR to fill receipt material

information and it can also issue the materials from

ledger. Issue Note and Gate pass while issuing the

materials shall be generated through the system. Ledger

updatation shall be done through User Module. User shall

able to track the transaction of the materials receipts and

issued using DTR transaction. Railway Working procedure

of accepting materials and issuing materials in S&T

department shall be maintained in the software. User shall

have facility to search for any product / any individual

leager report and see the detailed ledger report of that

product. User shall have the facility to take the ledger

reports in either in .xls and pdf format.(Inspection by

Consignee )

Numbers 5.00 392000.00 1960000.00

8 8 Supply of GSM Modem for User Inventory limit Alert -

Alert in the form of SMS in case any materials in depot

falls below threshold value configured in the system

(Inspection by Consignee )

Numbers 5.00 13440.00 67200.00


TENDER DOCUMENT


of 33 Run Date/Time: 07/02 /2019 14:45 :34

9 9 Supply of Barcode scanner ; USB based handheld 2D

camera type scanner for barcode tag reading of inventory

of decoding capabilities of UPC EAN, UPC EAN with

supplemental, Book land EAN, ISSN, UCC Coupon

Extended Code, Code128, GS1-128, ISBT 128, Code 39,

Code 39 Full ASCII, Trioptic Code 39, Code 32, Code 93,

Code11, Matrix 2 of 5, Interleaved 2 of 5, Discrete 2 of 5,

Codabar, MSI Chinese 2 of 5, GS1 DataBar variants,

Korean 3 of 5, ISBT Concat 2D, PDF417, MicroPDF417,

Composite Codes, Data Matrix, Maxicode, QR Code,

MicroQR, Aztec (Inspection by Consignee )

Numbers 5.00 31360.00 156800.00

10 10 Implementation Services for RDIM: Installations of RDIM

applications; Integration of GSM Modem; barcode

scanner and initial entry of User data, verifications of

ledgers by consultanting User to make system alive.

(Inspection by Consignee )

Numbers 5.00 56000.00 280000.00

Total 4098092.00

Schedule Schedule f-Training centre

Item- 01

Provision of TPWS {Design, manufacture and supply of Line side Electronic Unit (LEU) mainly consisting of

Balises(Switchable ,Fixed and Infill), Junction boxes,Power supply with suitable Power back up ,LEU, LEU

cabinet as per RDSO specification No. RDSO/SPN/182/2011 version2 or latest on the date of Tender opening as

per Special conditions of contract and Technical Specification enclosed in tender document. (Inspection by

RDSO)}

S No. Item

No


1 1 Design, manufacture and supply of LEU Modules , should

be compatible to existing system in AGC Div. (Inspection

by RDSO)

Numbers 1.00 312918.14 312918.14

2 2 Design, manufacture and supply of LEU Line side cabinet

( Inspection by Consignee)

Numbers 1.00 123963.36 123963.36

3 3 Design, manufacture and supply of Power supply for LEU.

( Inspection by Consignee)

Numbers 1.00 13200.00 13200.00

4 4 Design, Manufacture and supply of line side Eurobalise

(s) along with connecting cables based on signalling roll

plan etc. ( Inspection by Consignee)

Numbers 1.00 91471.00 91471.00

5 5 Supply of Junction boxes. ( Inspection by Consignee) Numbers 2.00 4719.00 9438.00

6 6 Supply of relays universal plug in type for LED signal lamp

(Q type ECRs) as per BRS941A Spec STS/E/Relays/AC

Lit LED signal / 09-2002 with latest amendment or Metal

To Metal for 110 V AC LED signal lamp as per

SPN.No.STS/E/RELAYS/AC LIT LED SIGNAL/09-2002

No. IRS: S: 46 AS PER DRG A-RT-RG-A-064 (Siemens

make) with base as per site requirement. (Inspection by

RDSO)

Numbers 4.00 5770.89 23083.56

7 7 Supply of portable testing equipment along with diagnostic

software for maintenance of train bome TPWS equipment

for use in sheds. This includes supply of documentation

for working instructions with each portable testing

equipment. (Inspection by Consignee)

Numbers 1.00 66000.00 66000.00

8 8 Supply hand hold maintenance tools for testing the line

side equipment/balise. (Inspection by Consignee)

Numbers 1.00 39600.00 39600.00

9 9 Installation of LEU Module with all accessories and

Cabinet

Numbers 1.00 10000.00 10000.00

10 10 Installation of Euroballises based on signaling roll plan. Numbers 1.00 5000.00 5000.00

Total 694674.06

Item- 02 AXLE COUNTERS

S No. Item

No



TENDER DOCUMENT


of 33 Run Date/Time: 07/02 /2019 14:45 :34

1 1 Supply, installation & commissioning of High availability

Digital Axle Counter consisting of Single section type as

per RDSO spec. No. RDSO/SPN/177/2005 (Ver-2) with

amend-1 or latest phase reversal type. (Inspection by

RDSO)

Set 1.00 596529.13 596529.13

2 2 Digital Axle counter(MSDAC) for the specified detection

points and track sections as per RDSO specification

RDSO/SPN/176/2013 (Version 3), for MSDAC with latest

amendment or specification OR on cross approval of all

equipment., complete set consisting of central

Evaluator/Processor, vital relays for each track section,

Track site unit with Detection Point complete assembly &

fixing arrangement for each detection point, clamps

deflectors for either side of each detection points,

monitoring console and a reset Box/Boxes for resetting

each track section (Inspection by RDSO) (3 track section

4 detection point)

Set 1.00 1423339.66 1423339.66

3 3 Installation commissioning & testing of MSDAC(3 track

section 5 detection point) IT includes Installation, wiring,

testing & commissioning of of track device (double rail

contact) of MSDAC, including digging of trench, track

crossing, laying of double walled antirodent corrugated

pipe from track side to location box and making its

terminations, fixing of deflector plates.(all other

accessories as per site requirement to be supplied by the

firm) and including Installation, wiring, testing &

commissioning of central evaluator, wiring from the CT

rack to the central evaluator and wiring of the Reset

boxes and wiring of the power supply to the evaluator

including supply of cable/shielded cable of required

conductor size as applicable with all accessories

10/16Sqmm PVC wire from equipment room to Central

Evaluator will be borne by contractor. This also includes

the painting & wiring work on the evaluator as per site

requirement.

Set 1.00 66245.64 66245.64

Total 2086114.43

Item- 03 DATA LOGGER EQUIPMENTS

S No. Item

No


1 1 Supply of FEP for networking. IRS:S-99/2006 Amend.3 or

latest. ( Inspection by Consignee) (Annexure -6 )

Numbers 1.00 140000.00 140000.00

2 2 Supply, installation, wiring, testing & commissioning of D/L

with 512 digital & 32 Analog inputs & accessories, power

supply arrangement, FEP ,modem ,monitoring unit

,complete with software system ( Inspection by

Consignee)

Numbers 1.00 449966.12 449966.12

3 3 Supply & installation of Computer Maintainer's console

with display unit. (Industrial embedded PC)(Inspection by

Consignee)

Numbers 1.00 354000.00 354000.00

4 4 Supply of Modem 2Mbps G.703 & V.35 as per RDSO

spec. RDSO/SPN/TC/80/2008. REV. 0.0 or latest.


Pair 1.00 17791.90 17791.90

5 5 Supply of Switches 8 port D-link or better make.


Numbers 1.00 4212.37 4212.37

6 6 Supply of PVC indoor cable 05pair 0.5mm from reputed

sources(Inspection by Consignee)

Metre 50.00 14.39 719.50

7 7 Supply & Installation and commissioning of LAN extender

4 Port as per RDSO/SPN/TC/82/2008. Rev 0.0 or latest.


Pair 2.00 16938.72 33877.44

8 8 Supply of CAT-6 data cable make D-Link or better make.


Metre 50.00 26.35 1317.50

9 9 Supply of RJ-45 connectors D-Link make or better make.


Numbers 10.00 5.50 55.00


TENDER DOCUMENT


of 33 Run Date/Time: 07/02 /2019 14:45 :34

10 10 Supply , testing and commissioning of 1KVA UPS with 3

hour backup of APC/ DELTA/ Aplab(ATUT) Make only


Numbers 1.00 21991.20 21991.20

11 11 Supply of battery monitoring unit for 110V as per

specification with 24V/4 Amps SMPS charger 230V A.C.

(1 Nos. ) Along with 12V , 18 AH battery(2 Nos.) , Opto to

RS485 Converter to interface with Data Logger, supply of

User Interface Module as per Technical specification

(Annexure- 7).

Numbers 1.00 160525.00 160525.00

12 12 Installation, Testing and Commissioning of Battery

Monitoring unit.

Numbers 1.00 22900.00 22900.00

Total 1207356.03

Item- 04 Provision for lifting barrier

S No. Item

No


1 1 Supply of Electrically operated lifting barrier set as per

specification no. RDSO/SPN/208/2012 (vER. 2) or latest,

with GI Boom in octagonal shape as RDSO standard

drawing no. RDSO/S 11600 and Motorized Boom Locking,

to work on 24VDC, each set consisting of 2 Nos. of 32ft.

Long Aluminum barrier with stop boards & lights, 2 Nos. of

lifting barrier pedestals each with 8 contacts circuit

controllers with top roller type limit switches of minimum

10000 operations life cycle, hand crank, 2 electric motors,

M.S. Counterweights, 2 Nos. of Boom stops with boom

locking, along with panel to have necessary

switches/buttons to operate one or both barriers, operate

boom lock only, or operate with push buttons in case of

24 V DC is available..(Inspection by RITES)

Set 2.00 312326.36 624652.72

2 2 Supply of gate signal operation cum indication panel

consisting of 2-way switches, LED indications etc. as per

standard practice. This panel shall be used in lieu of the

puller slide. (Inspection by Consignee)

Big Stn.

[5-6

Lines]

2.00 7621.85 15243.70

3 3 Supply of Desk type Electronic magneto Telephone as per

RDSO Spec. no.IRS: TC79/2000 amendment no.2 or

latest. (Inspection by Consignee)

Numbers 4.00 2640.81 10563.24

4 4 Supply of Road signal complete with signal post CLS unit

3 aspect ,ladder ,Base , LED signals & Hooter etc.


Numbers 4.00 54165.80 216663.20

5 5 Design Manufacturing and supply of sliding boom

arrangement, as per drawing no. Agra/S/305/SBB/009.


Set 2.00 71936.55 143873.10

6 6 Apparatus cases Full made of 10 SWG sheets with

miniature E Type Locks of same wards as that available

on existing location box of station without keys as per

spec. No IRS S 30/64 & RDSO Drg. No. SA 3376 with

latest amendments and as per Technical Specifications


Numbers 4.00 15625.30 62501.20

7 7 Installation, testing and commissioning of electrically lifting

barrier, complete with casting of cement concrete

foundation for pedestal and boom rest post as per

standard drawing , cabling power supply connection &

wiring with complete outdoor work including earthing of

barriers. This includes Wiring of Electrical lifting barrier set

complete with boom locking & panel including wiring of

electrical contact/controllers and group phone/master

slave unit with contractor's material, Hooter assembly

including termination of concerned cables at gate.

Set 2.00 51163.00 102326.00


TENDER DOCUMENT


of 33 Run Date/Time: 07/02 /2019 14:45 :34

8 8 Excavation, ramming, Casting Concrete foundation for

Colour Light Main Signal Post(for road signal) in the ratio

of 1:3:6, Aggregate not exceeding 3 : 8 cm, as per

Drg.No.SK-749 based on Drg No RST 11173 using

standard size galvanized Anchor bolts & nuts (also

referred to as foundation bolts) conforming to IRS Drg.

No. SA-116A/M, for erection of colour light signal post,

plastering with 1 : 4 cement - sand mixture all the

surfaces up to 75 mm below ground level, complete with

contractor's material including cement, sand, aggregate,

anchor bolts and nuts and curing of casted foundation,

refilling & ramming of loose soil around foundation and

disposal of loose dugged soil from site.

Numbers 4.00 11567.15 46268.60

9 9 Assembling, erection, installation & taking of cable inside

unit through post, termination and wiring of CLS complete

with all accessories of CLS unit, post, base, ladder, ladder

guards, platform and MS supporting bracket in the middle

of the ladder, hoods, pinnacles, offset brackets, etc.

including fixing & wiring of LED units lamps with

contractor's wiring material. (Road Signal)

Numbers 4.00 4629.50 18518.00

10 10 Fabrication & fixing of hylam sheet 10 mm thick, of

minimum grade P3, on apparatus case/Location boxes for

wiring of signaling circuits and cable termination, fixing on

suitable size contractor's angle with string rod for

supporting cable on back side, including fixing of all types

of terminals/ fuses as per location diagram/plan and

technical specifications, with drilling of holes on either

sides of terminals/ fuses and other places as required for

cable conductor / wires entry and fixing of sheet.

Numbers 4.00 1995.75 7983.00

11 11 Supply & installation of earth electrode assemble as per

Drg. No. DRM/S&T/JHS/214. This also includes fixing of

earth electrodes, ear thing of S & T apparatus cases

alongwith all equipments and cable armors along with

soldering at all locations as decided by the site engineer

of the Railways, signal post etc connected through

cable/GI wire 8 SWG supported on MS flat size 5mm x 40

mm to earth electrodes as per drg DRM/S&T/JHS/214

and practice on the division. Suitable brick masonry

enclosure to be provided around the earth. The earth

value should be less than 10 ohms including the lead

wire. It should be measured and painted on it. (Inspection

by Consignee)

Numbers 8.00 2714.21 21713.68

12 12 Supply of Disconnect Terminal block for Four conductor

with screwless Cage Clamp type/sliding switch disconnect

as per RDSO Specification No. RDSO/SPN/189/2004

version 1.2, for each conductor size upto 2.5 sq. mm.

Equivalent of M6 Terminals. Each Terminal block

equipped with two markers on top and bottom, an end

plate, 2 end clamps & adequate length rails for fitting

terminal blocks. ( Inspection by Consignee)

Numbers 200.00 144.16 28832.00

13 13 Termination of cable cores on disconnecting links /ARA

terminals, fuse blocks etc. in the apparatus cases,

provided on the cable termination rack. This includes all

associated works like pulling in/out the cable from

underground, peeling of insulation, dressing of cable

cores supported on insulating galvanized & PVC coated

M.S. string rods. (All dressing and insulating material

including string rods are to be supplied by contractor).

Per

Conductor

200.00 9.46 1892.00


TENDER DOCUMENT


of 33 Run Date/Time: 07/02 /2019 14:45 :34

14 14 Installation, fixing of (Relays, resistance chargers, bulb

holders & accessories etc) & wiring of the same in

apparatus cases as per location diagrams with

contractor's own wiring material suitable for 25 KV area.

This also includes supply & installation of Three pole

switch & socket 5A (Anchor make)and Lamp holders, two

pin, Bakelite type fixing arrangement at contractor own

cost. The work shall be done as per instruction of Railway

engineer at site. Apparatus case (Full)

Numbers 4.00 1446.39 5785.56

15 15 Casting of concrete foundation 2'x2'x3' with cement

concrete, sand of ratio 1:3:6 (Sliding Boom)

Job 20.00 2784.90 55698.00

16 16 Installation, testing, wiring & commissioning and Painting

of sliding boom.(including fixing relay/ARA/8way terminal,

termination of cable etc. as per direction of site incharge.

Job 2.00 6851.10 13702.20

Total 1376216.20

4. ELIGIBILITY CONDITIONS

Standard Financial Criteria

S.No. Description Confirmation

Required

Remarks

Allowed

Documents

Uploading

1

Total contract amount received by the tenderer during the last three financial years (i.e.

current year and last three financial years) should be a minimum of 150% of advertised

tender value of work. Tenderer is required to submit certificate to this effect which may

be an attested certificate from employer/client, audited balance sheet duly certified by

the Chartered Accountant.

No

No

Allowed

(Mandatory)

Submission of Affidavit


Required

Remarks

Allowed

Documents

Uploading

1

Please submit notarized affidavit on a non-judicial stamp paper in the prescribed format

(please download format from the link given below) for verification / confirmation of the

documents submitted for compliance of eligibility/qualifying criteria. Non submission of

properly filled affidavit in the prescribed format shall lead to summary rejection of your

offer.

Click here to download the format for Affidavit

No

No

Allowed

(Mandatory)

Standard Technical Criteria


Required

Remarks

Allowed

Documents

Uploading

1

(a) The tenderer must have successfully completed any of the following during last 07

(seven) years, ending last day of month previous to the one in which tender is invited:

Three similar works costing not less than the amount equal to 40% of advertised value

of the tender, or Two similar works costing not less than the amount equal to 50% of

advertised value of the tender, or One similar work costing not less than the amount

equal to 80% of advertised value of the tender. (b) (i)In case of composite works (e.g.

works involving more than one distinct component, such as Civil Engineering works,

S&T works, Electrical works, OHE works etc. and in the case of major bridges -

substructure, superstructure etc.), tenderer must have successfully completed any of

the following during last 07 (seven) years, ending last day of month previous to the one

in which tender is invited: Three similar works costing not less than the amount equal to

40% of advertised value of each component of tender, or Two similar works costing not

less than the amount equal to 50% of advertised value of each component of tender, or

One similar work costing not less than the amount equal to 80% of advertised value of

each component of tender. Note: Separate completed works of minimum required values

for each component can also be considered for fulfillment of technical eligibility criteria.

(b) (ii) In such cases, what constitutes a component in a composite work shall be clearly

pre-defined with estimated tender cost of it, as part of the tender documents without any

ambiguity. Any work or set of works shall be considered to be a separate component,

only when cost of the component is more than 2 crore each.

No

No

Allowed

(Mandatory)

1.1 Defination of Similar Work :- Any signalling work involving design , installation , testing

and commissioning of EI/PI/RRI. No No Not Allowed

5. COMPLIANCE

https://ireps.gov.in/ireps/upload/resources/Format%20for%20Affidavit%20for%20Credentials.pdf


TENDER DOCUMENT


of 33 Run Date/Time: 07/02 /2019 14:45 :34

Check Lst


Required

Remarks

Allowed

Documents

Uploading

1 Whether cost of tender document deposited online through payment gateway

provided on the website. No No Not Allowed

2 Whether cost of Earnest Money deposited online through payment gateway

facility provided on the website. No No Not Allowed

3

In case the Tenderer is a Private Limited / Limited Companies, uploading of

scanned copies o f the following documents: [ I ] Notary certified c opy of

Resolution o f t h e Directors o f t h e Company authorizing t h e o n e o f the

Directors / Managers of the company t o ac t o n behalf of the company. [ii]

Copy of Memorandum and Articles of Association of the Company. [iii] Power

of Attorney by the Company authorizing the person to act as per [I] above

No

No

Not Allowed

4

Uploading of Certificate by the Tenderer / all the members of the JV that they

have not been black listed or debarred by Railways o r any other Ministry/

Department o f t h e Government o f India/ PSU / State Government from

participation in tenders/ contract on the date of opening of bids either in their

individual capacity as members of the JV or the JV firm in which they were/are

members.

No

No

Not Allowed

5 Uploading o f Statement Showing the particulars o f Works o n Hand Works

Completed as per the format attached to the tender document. No No Not Allowed

6

In case the Tenderer is a Partnership Firm s , uploading of scanned copies of:

[I] Notary certified copy o f the Partnershipdeed o r Partnershipdeed duly

attested by Gazetted officer. [ii] Power ofAttorney in favour ofone of the

partners to act on behalf of the firm [only if such a power is not delegated in

partnership deed itself] and t o enter into liability b y signing t h e tender /

agreement.

No

No

Not Allowed

7 Submission of Details of Personnel to be deployed on work as per the format

attached to the tender document. No No Not Allowed

8

Submission of Certificate in support of Financial Eligibility . [a] Audited Balance

sheet duly certified b y Chartered Accountantclearly indicating contractual

payments . [b] Certificates from the Govt. department or Semi Governments /

PSUs for the work done for them.

No

No

Not Allowed

9 Tender Form as attached in prescribed format to be uploaded as per tender

document. No No Not Allowed

Commercial-Compliance


Required

Remarks

Allowed

Documents

Uploading

1

The earnest money and cost of tender document should be paid through

online payment, failing which the tenderer will not able to submit the offer.

Additional details regarding EMD is as per the Tender Document.

Yes

Yes

Not Allowed

2

Please enter the percentage of local content in the material being offered.

Please enter 0 for fully imported items, and 100 for fully indigenous items. The

definition and calculation of local content shall be in accordance with the Make

in India policy as incorporated in the tender conditions.

No

Yes

Allowed

(Optional)

3 Please submit your bank details i.e. Name of the Bank along with Bank Branch

Code, Account Number, IFSC Code, and PAN Number. No No

Allowed

(Mandatory)

4 Please furnish list of plant and Machinery available on hand own and proposed

to be inducted own and hired to be given separately for the subject work. No No

Allowed

(Mandatory)

5 Please furnish list of Works on hand indicating Description of Work, Contract

Value, Approximate value of balance work yet to be done and Date of award. No No

Allowed

(Mandatory)

6

Please furnish list of Works completed in last three financial years giving

Description of Work, Organization for whom executed, approximate value of

contract at time of award, Date of award and Date of Completion. Date of

actual Start, Actual Completion and Final value of Contract shall also be given.

No

No

Allowed

(Mandatory)

7 Please furnish list of personal, organization available on hand and proposed to

be engaged for the subject work. No No

Allowed

(Mandatory)

8 The accepted rates shall be deemed to include and cover all fees, taxes,

duties, royalties,rent etc. No No Not Allowed


TENDER DOCUMENT


of 33 Run Date/Time: 07/02 /2019 14:45 :34

9

Income Tax, Surcharge thereof, Goods & Service Tax (GST Act, 2017) and

any other applicable tax shall be recovered from contractor's bill as per rule in

force.

No

No

Not Allowed

10 Tender Form as attached in prescribed format to be uploaded as per tender

document. No No

Allowed

(Mandatory)

General Instructions


Required

Remarks

Allowed

Documents

Uploading

1

Tenderer (s) should attached the scan documents in support of minimum

eligibility criteria along with the tender. No document in support of minimum

eligibility criteria will be accepted/entertained after opening of tender.

No

No

Not Allowed

2 Applicability of JVs/ CONSORTIUM/ MOUs: JVs/ Consortium/ MOUs shall be

considered for the tenders of value more than Rs. 10 crore (Ten crore). No No Not Allowed

3 EARNEST MONEY & SECURITY DEPOSIT: No No Not Allowed

3.1

The Earnest Money deposited by the Contractor with his tender will be

retained by the Railways as part of security for the due and faithful fulfillment

of the contract by the contractor. The balance to make up the security deposit,

the rates for which are given below, may be deposited by the Contractor in

cash or may be recovered by percentage deduction from the contractor's "on

account" bills. Provided also that in case of defaulting contractor the Railway

may retain any amount due for payment to the Contractor on the pending "on

account bills" so that the amounts so retained may not exceed 10% of the total

value of the contract.

No

No

Not Allowed

3.2

Unless otherwise specified in the special conditions, if any, the Security

Deposit/rate of recovery/mode of recovery shall be as under:-a.Security

deposit for each work should be 5% of the contract value,b.The rate of

recovery should be at the rate of 10% of the bill amount till the full security

deposit is recovered,c.Security deposits will be recovered only from the

running bills of the contract and no other mode of collecting SD such as SD in

the form of instruments like BG, FD etc. shall be accepted towards security

deposit.The security deposit, however, shall be released only after the expiry

of the maintenance period and after passing the final bill based on 'No Claim

Certificate'.

No

No

Not Allowed

3.3 No interest will be payable upon the Earnest Money and Security Deposit or

amounts payable to the contractor under the contract. No No Not Allowed

4

The tenderer shall clearly specify whether the tender is submitted on his own

or on behalf of partnership concern. If the tender is submitted on behalf of a

partnership concern, he should submit the certified copy of partnership deed

along with the tender and authorization to sign the tender documents on

behalf of partnership firm. If these documents are not enclosed along with

tender documents, the tender will be treated as having been submit by

individual signing the tender documents. The Railway will not be bound by any

power of attorney granted by the tenderer or by changes in the composition of

the firm made subsequent to the execution of the contract. It may however

recognize such power of attorney and changes after obtaining proper legal

advise, the cost of which will be chargeable to the contractor

No

No

Not Allowed

5

The tenderer whether sole proprietor, a limited company or a partnership firm

if they want to act through agent or individual partner(s) should submit along

with the tender or at a later stage, a power of attorney duly stamped and

authenticated by a Notary Public or by Magistrate in favour of the specific

person whether he /they be partner(s) of the firm or any other person

specifically authorizing him/them to submit the tender, sign the agreement,

receive money, witness measurements, sign measurement book, compromise

, settle, relinquish any claim(s) preferred by the firm and sign No Claim

Certificate and refer all or any disputes to arbitration.

No

No

Not Allowed

6

The Tenderers having more than 20 labour, is required to obtain the labour

license from the licensing Officer under Provision of Contract Labour

(Regulation and Abolition) Act 1970 read with Contract Labour (Regulation and

Abolition) Central Rules 1970. They should obtain a proper and valid labour

license for the concerned work from the concerned Asstt. Labour

Commissioner or licensing officer of the area and the photo copy of the labour

license must be submitted to Railway for records . Failure to do so will attract

legal action against the tenderer

No

No

Not Allowed


TENDER DOCUMENT


of 33 Run Date/Time: 07/02 /2019 14:45 :34

7

In case any contradiction between general condition of contract & special

conditions ofcontract, special conditions of contract will prevail over general

conditions of contract.

No

No

Not Allowed

8

If the tenderer(s) deliberately gives / give wrong information in his/their tender

or creates/create circumstances for the acceptance of his/their tender, the

Railway reserves the right to reject such tender at any stage.

No

No

Not Allowed

9

The General Conditions of Contract governing the performance of the works

covered by this tender are the Indian Railway Standard General Conditions of

Contract [IRSGCC Nov 2018] as amended from time to time up to date. A soft

copy of the Indian Railway Standard General conditions of Contract is

uploaded in the attached documents to the tender for reference. Hard copy of

IRSGCC (with up-to-date correction slip) may be pursued in the office of the Sr

DSTE Co /AGC. The tenderer/s is/are deemed to have kept

himself/themselves fully Informed of the provisions of the IRS General

conditions of Contract including all corrections and Amendments issued up to

date while submission of offer and any claim that he/they is/are not aware of

any amendment or correction slip to the IRSGCC shall not be entertained

No

No

Not Allowed

Technical-Compliances


Required

Remarks

Allowed

Documents

Uploading

1

Submission of 'Undertaking by the tenderer' that the equipment for EI shall be

procured from RDSO approved sources and installation, testing and

commissioning of EI shall also be got done from the same source including

after sales support required during the warranty period.

No

Yes

Allowed

(Mandatory)

1.1

After the award of the contract, MOU with RDSO approved source covering

supply of equipment for EI, Installation, testing & commissioning of EI by the

same RDSO approved source including after sales support required during the

warranty period, before supply of equipments is undertaken.

No

Yes

Allowed

(Mandatory)

Undertakings


Required

Remarks

Allowed

Documents

Uploading

1

Until a formal agreement is prepared and executed, acceptance of this tender

shall constitute a binding contract between us subject to modifications, as may

be mutually agreed to between us and indicated in the letter of acceptance of

my/our offer for this work.

No

No

Not Allowed

2

I/We also hereby agree to abide by the Indian Railways Standard General

Conditions Of Contract IRSGCC Nov 2018, with all correction slips up-to-date

and to carry out the work according to the Special Conditions of Contract and

Specifications of materials and works as laid down by Railway in the annexed

Special Conditions/Specifications, Schedule of Rates with all correction slips

up-todate for the present contract.

No

No

Not Allowed

3

I/We have read the various conditions to tender attached hereto and agree to

abide by the said conditions. I/We also agree to keep this tender open for

acceptance for a period of 60 days from the date fixed for opening the same

and in default thereof, I/We will be liable for forfeiture of my/our Earnest Money

. I/We offer to do the work for North Central Railway, at the rates quoted in the

attached schedule and hereby bind myself/ourselves to complete the work in

all respects within the period of completion stipulated in the tender document,

from the date of issue of letter of acceptance of the tender.

No

No

Not Allowed

4 I/ We have visited the works site and I / We am / are aware of the site

conditions. No No Not Allowed

5 I have read the entire tender document including uploaded documents and

corrigendum (if any). No No Not Allowed

6 I/We have read the various conditions attached/referred to in this tender

document and agree to abide by the said conditions. No No Not Allowed

7

I/We hereby confirm that the rates, rebates and/or other financial terms, if any,

quoted by us in the relevant fields of the Financial Bid page will only be the

ruling terms for deciding the inter-se-ranking and any such conditions having

financial repercussions, if quoted by us anywhere else including attached

documents shall not be considered for deciding inter-se-ranking.

No

No

Not Allowed


TENDER DOCUMENT


of 33 Run Date/Time: 07/02 /2019 14:45 :34

8

I t i s agreedthat, If, I/we deliberately give/submit wrong information i n the

tender or create circumstances for the acceptance of the tender, the Railway

reserves the right t o reject such tender a t any stage. The entire Earnest

Money Deposit with the Railway will be forfeited. In addition action will be taken

t o suspend the business with the tenderer for aspecified period at the

discretion of Railway Administration.

No

No

Not Allowed

9

It is certified that I/We have not been blacklisted or debarred by railways or

any other ministry/department/public sector undertaking of the government of

India/State Government from participation in tenders/contract on the date of

tender opening of bids, either in individual capacity or as a member of JV firm

in which I/We were/are members.

No

No

Not Allowed

10

I/We abide by the provisions of Payment of Wages act & Minimum Wages act

in terms of clause 54 and 55 of Indian Railways General Condition of Contract.

I/We aware of registration of firm on website

'www.shramikkalyan.indianrailways.gov.in'and upload requisite details of

labour and their payment in this portal. These details shall be available in

public domain.

No

No

Not Allowed

6. Documents attached with tender

S.No. Document Name Document Description

1 TenderdocumentTechnicalBID.pdf Tender document Technical Bid

2 KXMEIWORK.pdf SIP of KXM

3 FAREIWORK.pdf SIP of FAR

4 EligibilityCriteria.pdf EligibilityCriteria

5 Affidavit.pdf Affidavit

6 Annexure.pdf Annexure

7 BankDetail.pdf Bank Details

8 PaymentCondition.pdf Payment Condition

9 TenderdocumentFinancial.pdf Tender Document Financeial Bid

This tender complies with Public Procurement Policy (Make in India) Order 2017, dated 15/06/2017, issued by

Department of Industrial Promotion and Policy, Ministry of Commerce, circulated vide Railway Board letter no.

2015/RS(G)/779/5 dated 03/08/2017 and 27/12/2017.

Signed By: PRIYANKA SINGH

Designation : DSTEW

agra division-s and t/north central rly tender document

Documents

Transcript of agra division-s and t/north central rly tender document