Dirjen Migas No 84K-1998 Pemeriksaan Keselamatan Kerja (Dwi Bahasa)
Transcript of Dirjen Migas No 84K-1998 Pemeriksaan Keselamatan Kerja (Dwi Bahasa)
-
8/2/2019 Dirjen Migas No 84K-1998 Pemeriksaan Keselamatan Kerja (Dwi Bahasa)
1/19
PEDOMAN DAN TATACARA PEMERIKSAAN
KESELAMATAN KERJA ATAS INSTALASI,
PERALATAN DAN TEKNIK YANG
DIPERGUNAKAN DALAM USAHA
PERTAMBANGAN MINYAK DAN GAS BUMI
DAN PENGUASAAN SUMBERDAYA PANAS
BUMI
INSPECTION GUIDELINES FOR SAFETY ON
FACILITIES, EQUIPMENT AND
TECHNOLOGY USED IN OIL AND GAS AND
GEOTHERMAL ACTIVITY
Keputusan Direktur Jenderal Minyak dan Gas Bumi
Nomor : 84.K/38/DJM/1998
The Director General of Oil and gas Decree Nor:
84.K/38/DJM/1998
DEPARTEMEN PERTAMBANGAN DAN
ENERGI REPUBLIK INDONESIA
DIREKTUR JENDERAL MINYAK DAN GAS
BUMI,
DEPARTMENT OF MINES AND ENERGY OF
THE REPUBLIC INDONESIA
DIRECTOR GENERAL OF OIL AND GAS
Menimbang : Considering:
Bahwa dalam rangka kelancaran pelaksanaanpemeriksaan keselamatan kerja atas instalasi,
peralatan dan teknik yang dipergunakan dalam usaha
pertambangan minyak dan gas bumi dan
pengusahaan sumberdaya panas bumi dan sebagai
pelaksanaan lebih lanjut Peraturan Menteri
Pertambangan dan Energi Nomor 06 P/0746/
M.PE/1991 tanggal 19 November 1991, dianggap
perlu menetapkan Pedoman dan Tatacara
Pemeriksaan Keselamatan Kerja atas Instalasi,Peralatan dan Teknik Yang Dipergunakan Dalam
Usaha Pertambangan minyak dan Gas bumi Dan
Pengusahaan Sumberdaya Panasbumi dalam suatu
keputusan Direktur Jenderal Minyak Gas Bumi
that in order to smoothen the inspection guidelinesfor safety on installation, equipment and techniques
in oil and gas and geothermal activities and as
further implementation of the Mines and Energy
Minister's Regulation Number 06 P/ 0746/
M.PE/1991 dated 19 November 1991, it is deemed
necessary to stipulate Inspection Guidelines for
Safety on Installation, Equipment, and Techniques
in Oil and Gas and Geothermal Activities in a
Decree of the Director General of Oil and Gas;
Mengingat: In view of:
1. Undang-undang Nomor 44 Prp Tahun 1960(L.N. Tahun 1960 Nomor 33, TLN Nomor
2070);
1.
2.
3.
4.
5.
6.
7.
8.
1. Law No.44 Prp Year 1960 (L.N 1960 No.
33, TLN No. 2070);
2. Undang-undang Nomor 8 Tahun 1971 (L.N.Tahun 1971 Nomor 76, TLN Nomor 2970)
2. Law No. 8 Year 1971 (L.N. 1971 No. 76,
TLN No. 2970)
3. Peraturan Pemerintah Nomor 11 tahun 1979(L.N. Tahun 1979 Nomor 18, TLN Nomor
3135)
Government Regulation No. 11 Year 1979
(L.N. Year 1979 No. 18, TLN Nomor 3135).
4. Keputusan Presiden Nomor 22 Tahun 1981tanggal 1 Juni 1981 jo Keputusan Presiden
Nomor 45 1991 tanggal 1 Oktober 1991;
Decree of President No. 22 Year 1981, 1 June
1981 jo Decree of President No. 45 1991, 1
October 1991;
5. Keputusan Presiden Nomor 374/M Tahun 1995tanggal 23 November 1995;
Decree of President No. 374/M Year 1995, 23
November 1995;
6. Peraturan Menteri Pertambangan dan EnergiNomor 02/PM/Pertamb/1975 tanggal 10 Maret
1975;
Regulation of Mines and Energys minister No.
02/PM/Pertamb/1975, 10 March 1975;
7. Keputusan Menteri Pertambangan dan EnergiNomor 02 P/M/Pertam/1979 tanggal 30 Juni1979;
Decree of Mines and Energy No. 02
P/M/Pertamb/1979, 30 June 1979;
8. Keputusan Menteri Pertambangan dan EnergiNomor 521/Kpts/1979 tanggal 20 Juni 1979;
Decree of Mines and Energy No.521/Kpts/1979, 20 June 1979;
Page 1 of 19
-
8/2/2019 Dirjen Migas No 84K-1998 Pemeriksaan Keselamatan Kerja (Dwi Bahasa)
2/19
9. Peraturan Menteri Pertambangan dan EnergiNomor 06 P/0746/M.PE/1991 tanggal 19
Nopember 1991;
9.
10.
11.
Regulation of Mines and Energy No. 06
P/0746/M.PE/1991, 19 November 1991;
10. Keputusan Menteri Pertambangan dan EnergiNomor 300.K/38/M.PE/1997 tanggal 28 April
1997;
Decree of Mines and Energy No.
300.K/38/M.PE/1997, 28 Avril 1997;
11. Peraturan Direktur Jenderal Minyak dan GasBumi Nomor 43/382/DDJ/1992 tanggal 19September 1992;
Regulation of Mines and Energy No.43/382/DDJ/1992,
MEMUTUSKAN : HAS DECIDED :
Menetapkan : To Determine:
Pasal 1 Article 1
(1) Segala definisi atau pengertian yangdipergunakan dalam Keputusan ini adalah
definisi atau pengertian sebagaimana dimaksuddalam Pasal 1 Keputusan Menteri
Pertambangan dan Energi Nomor
06P/0746/M.PE/1991 tanggal 19 Nopember
1991.
(1) All definitions or understandings used in thisDecree shall be the definitions or
understandings as referred to in Article 1 of theMinister of Mines and Energy's Decree No.
06P/0746/M.PE/1991 dated 19 November
1991.
(2) Selain sebagaimana telah ditetapkan pada ayat(1), dalam Keputusan ini yang dimaksud
dengan :
(2) Other than as stipulated in subsection (1), inthis Decree:
a. Sertifikat Kelayakan Penggunaan, adalahpersetujuan yang diberikan Direktur
Jenderal atau operasi atau penggunaan
Instalasi dan Peralatan setelah dilakukan
pemeriksaan Keselamatan Kerja, yang
berupa Sertifikat Kelayakan Penggunaan
Instalasi (SKPI) dan Sertifikat Kelayakan
Penggunaan Peralatan (SKPP);
a. Worthiness Certificate shall be anyapproval given by the Director General for
the operation or use of Installation and
Equipment after Work Safety Inspection in
the form of Installation Worthiness
Certification (SKPI) and Equipment
Worthiness Certificate (SKPP);
b. Direktorat Jenderal, adalah DirektoratJenderal Minyak dan Gas Bumi;
b. Directorate General, shall be theDirectorate General Oil and gas;
c. Direktut, adalah Direktur TeknikPertambangan Minyak dan Gas Bumi.
c. Directorate General, shall be theDirectorate General Oil and gas
d. Direktorat Teknik, adalah DirektoratTeknik Pertambangan Minyak dan Gas
Bumi;
d. Director of Engineering, shall be Directorof Oil and gas Mining Techniques;
e. Kepala Pelaksana Inspeksi Tambang,
adalah Kepala Inspeksi Tambang Minyakdan Gas Bumi.
e. Executive Head of Mine Inspection, shall
be the Head of Oil and gas MineInspection;
f. Pelaksana Inspeksi Tambang, adalahpejabat Direktorat Jenderal yang diangkat
oleh Direktur jenderal;
f. Mine Inspector, shall be the official of theDirectorate General appointed by the
Director General;
g. Perusahaan adalah Pertamina, KontraktorKontrak Production Sharing, Technical
Assistance Contract, Join Operating Body,
dan mitra kerja Pertamina lainnya dalam
Operasi Bersama Pengusahaan SumberdayaPanasbumi;
g. Company shall be Pertamina, ProductionSharing Contractor, Technical Assistance
Contract, Joint Operating Body, and other
partners of Pertamina in Oil and gas
operation and Joint Operation Contractorfor Geothermal Exploration;
h. Perusahaan Jasa adalah Perusahaan Jasa
Inspeksi Teknik dalam bidangpertambangan minyak dan gas bumi dan
h. Service Company shall be a Company of
Technical Inspection Services in oil andgas mining activities and geothermal
Page 2 of 19
-
8/2/2019 Dirjen Migas No 84K-1998 Pemeriksaan Keselamatan Kerja (Dwi Bahasa)
3/19
pengusahaan sumberdaya panasbumi yang
telah mendapatkan penunjukkan Direktur
Jenderal;
exploration that has been assigned by the
Director General.
Pasal 2 Article 2
(1) Terhadap Instansi dan Peralatan dalam Operasipertambangan minyak dan gas bumi wajib
dilaksanakan pemeriksaan Keselamatan Kerja.
(1) With regard to Installation and Equipment inOil and gas mining activities shall be obligated
to carry out Work Safety Inspection.
(2) Pemeriksaan Keselamatan Kerja sebagaimanadimaksud pada ayat (1) dilakukan terhadap
Instansi dan Peralatan yang :
(2) The Work Safety Inspection as referred to insubsection (1) shall be carried out upon
Installation and Equipment:
a. akan dipasang atau didirikan; a. To be installed or constructed;
b. sedang dipasang atau didirikan; b. Being installed or constructed;
c. telah dipasang atau didirikan. c. Already installed or constructed.
(3) Terhadap peralatan yang dibuat berdasarkan
pesanan dan bukan merupakan produksi massal,pemeriksaan Keselamatan Kerja dapatdilakukan ditempat pembuatan peralatan.
(3) With regard to any equipment made based on
order and not constituting mass production,Work Safety Inspection can be carried out onthe equipment manufacturing plant.
Pasal 3 Article 3
Instalasi dan Peralatan yang wajib dilaksanakan
pemeriksaan Keselamatan Kerja adalah sebagaimana
termaksud dalam Lampiran I Keputusan ini.
The Installation and Equipment subject to a Work
Safety Inspection shall be as referred to in Annex I
of this Decree.
Pasal 4 Article 4
(1) Pemeriksaan Keselamatan Kerja atas Instansidan Peralatan sebagaimana dimaksud dalam
Pasal 2 dilaksanakan oleh Pelaksana Inspeksi
Tambang dan atau oleh Perusahaan Jasa.
(1) Work Safety Inspection for the Installation andEquipment as referred to in Article 2 carried
out by the Mine Inspector and or by Service
Company.
(2) Tata cara Pemeriksaan Keselamatan Kerja atasInstansi dan Peralatan adalah sebagaimana
termaksud dalam Lampiran II Keputusan ini.
(2) Procedure for Work Safety Inspection for theInstallation and Equipment shall be as referred
to in subsection II of this Decree.
Pasal 5 Article 5
(1) Terhadap Instansi dan Peralatan yang telahdilaksanakan pemeriksaan Keselamatan Kerja
diberikan Sertifikat Kelayakan PenggunaanInstansi (SKPI) dan Sertifikat Kelayakan
Penggunaan Peralatan (SKPP) oleh Direktur
Jenderal.
(1) Any Installation and Equipment for which aWork Safety Inspection has been carried out,
shall be given a Installation WorthinessCertificate (SKPI) and Equipment Worthiness
Certificate (SKPP) by the Director General.
(2) Sertifikat Kelayakan Penggunaan Instansi(SKPI) dan Sertifkat Kelayakan Penggunaan
Peralatan (SKPP) sebagaimana dimaksud pada
ayat (1) berlaku selama jangka waktu 5 (lima)
tahun untuk SKPI dan 3 (tiga) tahun untuk
SKPP, atau kurang dari jangka waktu tersebut
di atas apabila Instansi dan Peralatan tersebut
mengalami perubahan atau diragukan
kemampuannya.
(2) Installation Worthiness Certificate (SKPI) andEquipment Worthiness Certificate (SKPP) as
referred to in subsection (1) shall be effective
for a period of 5 (five) years for SKPI and 3
(three) years for SKPP, or less than the period
as mentioned above if the Installation and
Equipment have been amended or their
capability is doubted.
(3) Setelah selesainya jangka waktu sebagaimana (3) After the expiry of period as referred to in
Page 3 of 19
-
8/2/2019 Dirjen Migas No 84K-1998 Pemeriksaan Keselamatan Kerja (Dwi Bahasa)
4/19
dimaksud pada ayat (2), terhadap Instansi dan
Peralatan wajib dilakukan pemeriksaan
Keselamatan Kerja sebagaimana dimaksud
dalam 2.
subsection (2), the Installation and Equipment
shall be subject to a Work Safety Inspection as
referred to in Article 2.
Pasal 6 Article 6
Setelah dilaksanakan evaluasi terhadap teknik yangakan dipergunakan sebagaimana termaksud dalam
Lampiran I huruf C, Direktur Jenderal Cq Direktur
memberikan pengesahan
After the techniques to be applied have beenevaluated as referred to in Annex I letter C, Director
General in this case the Director giving the
authorization.
Pasal 7 Article 7
Besarnya biaya pemeriksaan Keselamatan Kerja atas
Instansi Peralatan yang dilaksanakan oleh
Perusahaan Jasa ditetapkan berdasarkan mekanisme
pasar tenaga kerja bidang minyak dan gas bumi.
The costs for Work Safety Inspection for the
Installation and Equipment carried out by the
Service Company shall be stipulated pursuant to the
manpower market mechanism in the field of oil and
gas.
Pasal 8 Article 8
Dalam jangka waktu 6 (enam) bulan sejak
berlakunya Keputusan ini, Perusahaan yang telah
beroperasi atau telah menggunakan Instansi dan
Peralatan dan belum melakukan ketentuan dan
Keputusan ini wajib mengajukan permohonan
pemeriksaan Keselamatan Kerja atas Instansi,
Peralatan dan Teknik yang dipergunakan kepada
Direktorat Jenderal cq. Direktorat Teknik.
Within the period of 6 (six) months as of the
enactment of this Decree, any Company that has
been in operation or has been using the Installation
and Equipment and not yet carried out the provisions
of this Decree shall be obligated to request a Work
Safety Inspection for the Installation, Equipment and
Techniques used to the Director General in this case
the Directorate of Engineering.
Pasal 9 Article 9
Apabila terdapat kekurangan-kekurangan pada
Instansi atau Peralatan setelah diadakan pemeriksaan
Keselamatan Kerja, maka dalam waktu yang
ditetapkan oleh Direktur, Perusahaan wajib
mengadakan perbaikan atau perubahan sehingga
Instansi dan Peralatan tersebut memenuhi hal-hal
yang disyaratkan oleh peraturan perundang-
undangan yang berlaku.
If there are shortcomings in the Installation or
Equipment after a Work Safety Inspection, then
within the period as stipulated by Director, the
Company shall be obligated to carry out repair or
modification so the Installation and Equipment meet
the requirements pursuant to the prevailing laws and
regulations.
Pasal 10 Article 10
Keputusan ini berlaku pada tanggal ditetapkan. This Decree shall be effective on the date of itsenactment.
Ditetapkan di Jakarta Stipulated in Jakarta
Pada tanggal 19 Agustus 1988 On 19 August 1998
Direktur Jenderal Minyak dan Gas Bumi Director General of Oil and gas,
Soepraptono Soeleiman Soepraptono Soeleiman
Page 4 of 19
-
8/2/2019 Dirjen Migas No 84K-1998 Pemeriksaan Keselamatan Kerja (Dwi Bahasa)
5/19
Lampiran I Keputusan Direktur Annex I of the Director General of
Jenderal Minyak dan Gas Bumi Oil and gas' Decree
Nomor: /38/DJM/1988 No.: /38/DJM/1998
Tanggal Date :
Intalasi dan Peralatan yang Wajib Dilaksanakan
Pemeriksaan Keselamatan Kerja
Installation and Equipment for which a Work
Safety Inspection is Obligatorily Carried Out
A. Instalasi A. Installations
1. Instalasi Eksplorasi dan Eksploitasi: 1. Exploitation and exploration instalation
a. Instansi pemboran; a. Drilling installation;
b. Instalasi produksi; b. Production installation;
c. Instalasi pengumpul; c. Collecting installation;
d. Instalasi lainnya yang terkait dengankegiatan Eksplorasi dan Eksploitasi.
d. Other installation associated withExploration and Exploitation
activities.
2. 1Instalasi Pemurnian dan Pengolahan : 2. Purification and Processing Installations
a. Instalasi Pemurnian dan Pengolahan; a. Purification and Processinginstallation;
b. Pembongkaran dan Pemuatan; b. Loading and Unloading;c. Instalasi lainnya yang terkait dengan
kegiatan Pemurnian dan Pengolahan
baik langsung maupun tidak langsung
berhubungan dengan kegiatan
termaksud.
c. Other installations associated withPurification and Processing activities
in connection, either directly or
indirectly, with the corresponding
activities.
3. Instalasi Penimbunan dan Pemasaran yangdimaksud adalah :
3. Storage and Marketing installations:
a. Instalasi Seafed Depot; a. Seafed Depot Installation;
b. Instalasi Inland Depot; b. Inland Depot Installation;
c. Instalasi Depot Pengisian Pesawat
Udara (DPPU);
c. Airplane Filling Depot Installation
(DPPU);
d. Intalasi Transit Terminal; d. Transit Terminal Installation;
e. Instalasi Stasiun Pengisi Bahan Bakar(SPBU) dan Stasiun Pengisian Bahan
Bakar Gas (SPBG);
e. Public Gas Station (SPBU) and GasFuel Filling Station Gas (SPBG);
f. Instansi lainnya yang terkait dengankegiatan penimbunan dan pemasaran.
f. Other installations associated withstorage and marketing activities.
B. Peralatan B. Equipment.
1. Katup pengamanan, yaitu peralatan yang
berguna untuk melindungi peralatan danfasilitas yang terkait meliputi :
1. Safety Valves namely any equipment useful
to protect relevant equipment and facilitiescover:
Page 5 of 19
-
8/2/2019 Dirjen Migas No 84K-1998 Pemeriksaan Keselamatan Kerja (Dwi Bahasa)
6/19
a. Safety Valve; a. Safety Valve;
b. Relief Valve; b. Relief Valve;
c. Safety Relief Valve; c. Safety Relief Valve;
d. Thermal Relief Valve; d. Thermal Relief Valve;
e. Pilot Operated Safety Valve; e. Pilot Operated Safety Valve;
f. Vacuum Relief Valve. f. Vacuum Relief Valve;
2. Bejana Tekan dan sejenisnya, yaituperalatan yang bekerja dengan tekanan
kerja didalam peralatan melebihi 1/2 Atm
tekanan lebih (gauge), atau bejana vakum
dengan tekanan kerja didalam peralatan
kurang dari 1 atm absolut.
2. Pressure Vessel and similar devices namelyany equipment working under a work
pressure in the equipment exceeding 1/2
Atm of overpressure (gauge), or vacuum
pressure under a work pressure in the
equipment less than 1 Atm absolute.
3. Pesawat Angkat, yaitu untukmemindahkan, mengangkat barang secara
vertikal dan atau horizontal dalam jarak
ditentukan, antara lain meliputi:
3. Lifting Devices namely any equipment toremove, to lift any goods in vertical and or
horizontal direction in a stipulated
distance, cover:
a. Pesawat Angkat Bergerak; a. Mobile lifting device;
b. Pesawat Angkat Tetap; b. Fixed lifting device;
c. Pesawat Angkat di atas kepala. c. Overhead lifting device;
4. Peralatan Listrik, yaitu peralatan yangmembangkit, mendistribusi dan
mengendalikan sistem tenaga listrik,
meliputi :
4. Electrical Equipment namely anyequipment which generates, distributes and
controls a power system covers:
a. Unit Power Generator; a. Power Generator Unit;
b. Unit Power Transformer; b. Power Transformer Unit;
c. Unit Switchgear; c. Switchgear Unit;
d. Unit Motor Control Center. d. Motor Control Center Unit.
5. Peralatan Putar, yaitu peralatan yangberfungsi memindahkan atau memanpatkan
minyak, gas serta panasbumi meliputi :
5. Rorating Equipment namely any equipmentserving to remove or compress petroleum,
gas, and geotherm covers:
a. Unit Kompresor; a. Compressor Unit;
b. Unit Pompa. b. Pump Unit.
6. Pipa Penyalur, yaitu bentang pipa berikutfasilitas-fasilitas terkait yang digunakan
untuk mengalirkan dan menyalurkan
minyak dan gas bumi serta panas bumi.
6. Distribution pipes, namely a network ofpipes with relevant facilities used to flow
and distribute oil and gas and geotherm.
c. Teknik Yang Dipergunakan a. Techniques Used
Teknik yang dipergunakan, yatiu tatacara atau
prosedur yang akan dipergunakan dalam operasi
pertambangan minyak dan gas bumi antara lain,
meliputi :
Techniques used namely procedures to be used in
Oil and gas mining activities cover:
1. Spesifikasi Prosedur Las (WPS) dan Rekaman
Kualifikasi Prosedur (PQR);
1. Specification of Welding Procedures (WPS) and
Procedure Qualification Records (PQR);
2. Catatan Unjuk Kerj (Sertifikat) Juru
Las/Operator Las;
2. Performance Note (Certificate) of
Welder/Welding Operator;
3. Prosedur Uji Tekan Pipa Penyalur; 3. Pressure Testing Procedures of Distribution
Page 6 of 19
-
8/2/2019 Dirjen Migas No 84K-1998 Pemeriksaan Keselamatan Kerja (Dwi Bahasa)
7/19
Pipes;
4. Prosedur Uji Beban Pesawat Angkat; 4. Load Test Procedures of Lifting Devices;
5. Prosedur Reparasi, Modifikasi dan Alterasi. 5. Procedures for Reparation, Modification and
Alteration.
Ditetapkan di Jakarta Stipulated in Jakarta
Pada tanggal 19 Agustus 1998 On,August 19,1998
Direktur Jenderal Minyak dan Gas Bumi Director General of Oil and gas
Soepraptono Soeleiman Soepraptono Soeleiman
Lampiran II Keputusan Direktur Annex I of the Director General of
Jenderal Minyak dan Gas Bumi Oil and gas' Decree
Nomor Number: /38/DJM/1998
Tanggal Date :
Tata Cara Pemeriksaan Keselamatan Kerja atasInstalasi dan Peralatan
Procedurefor Work Safety Inspection for TheInstallation and Equipment
I. Pemeriksaan Keselamatan Kerja Instalasi I. Work Safety Inspection of Installation
A. Pemeriksaan Keselamatan Kerja Instalasi
meliputi penilaian perencanaan dengan
melaksanakan penelaahan terhadap data :
A. Work Safety Inspection of Installation coveres
evaluation of planning by carrying out review of
data:
a. Peralatan proses, utilitas dan pengolahlimbah;
b. Process equipmeSnt, utilities and wasteprocessing equipment;
b. Alat ukur dan metering; c. Measuring devices and metering;
c. Sistem perpipaan; d. Piping system;
d. Sistem instrumentasi; e. Instrumentation system;
e. Piranti Pengaman f. Safety devices;
f. Tangki Timbul; g. Storage tanks;
g. Sistem pencegahan dan penanggulangankebakaran;
h. Fire prevention and control system;
h. Sistem pencegahan dan pemantauanpencemaran lingkungan;
i. Environmental pollution prevention andmonitoring system;
i. Peralatan lain; j. Other equipment;
j. Diagram alir proses dan diagram pipa &instrumen;
k. Process flow diagrams and pipe &instrument diagrams;
k. Gambar tata letak peralatan; l. Layout drawing of equipment;
l. Pekerjaan sipil; m. Civil works;
Page 7 of 19
-
8/2/2019 Dirjen Migas No 84K-1998 Pemeriksaan Keselamatan Kerja (Dwi Bahasa)
8/19
m. Klasifikasi daerah berbahaya (hazardousarea classification);
n. Hazardous area classification;
n. Electrical one line diagram; o. Electrical one-line diagram;
o. Gambar tata letak pentanahan (groundinglay-out);
p. Grounding layout drawing;
p. Diagram cause & effect / SAFE Chart; q. Cause & effect diagram / SAFE Chart;
q. Prosedur kerja pengoperasian peralatan; r. Operating procedures for equipment;
r. Prosedur evakuasi darurat; s. Procedures for emergency evacuation;
s. Surat persetujuan atau rekomendasi dariinstansi yang berwenang untuk program
Pengolahan dan Pemantauan Lindungan
Lingkungan.
t. Letter of approval or recommendation fromthe authorized institution for the
environmental management and
management proggrams.
A. Pemeriksaan Fisik A.Physical Inspection.
Pemeriksaan fisik meliputi : Physician inspection covers:
1. Pemeriksaan Instalasi untuk memastikansesuai tidaknya Intalasi dengan
perencanaan, spesifikasi, prosedur
pembuatan dan pemasangan.
3. Inspection of Installation to verify theconformance of Installation with the
planning, specification, production and
installation procedures.
2. Memeriksa Kelengkapan Mutu Peralatan,Teknik Keselamatan Kerja dan Lindungan
Lingkungan meliputi :
4. Inspection of Equipment Quality, WorkSafety Techniques and Environmental
Protection covers:
a. Alat Pemadam kebakaran; a. Fire fighting equipment;
b. Alat deteksi api, panas, asap dan gasberbahaya;
b. Fire, heat, smoke and hazardous gasdetection devices;
c. Alat perlengkapan penyelamatan danpelindung perorangan;
c. Individual safety and protectionequipment;
d. Sistem komunikasi; d. Communication system;
e. Sistem kontrol dan penghentian darurat(emergency shutdown system);
e. Emergency control and shutdownsystem;
f. Pemeriksaan tangga, lampu, bordes danhandrail;
f. Inspection of stairs, lamps, balustradeand handrail;
g. Flaring; g. Flaring;
h. Rock Muffler; h. Rock Muffler;
i. Peralatan pencegahan danpenanggulangan pencemaran
lingkungan;
i. Environmental pollution prevention andcontrol equipment;
j. Sistem untuk meniadakan bahaya listrikstatis dan arus listrik lainnya;
j. System to eliminate static electricalhazards and other electrical current;
k. Tanda-tanda keselamatan kerja, antaralain; tanda peringatan, larangan kode
warna dan tanda lainnya.
k. Work safety signs, such as; warningsigns, prohibitions, color code and other
signs.
1. Memeriksa Kelengkapan SertifikatKelayakan Penggunaan peralatan, SertifikatKelayakan Konstruksi Platform serta Ijin
Penggunaan dari Instansi teknis terkait
antara lain:
1. Inspection of the completeness of EquipmentWorthiness Certificate, PlatformConstruction Worthiness Certificate, Permit
of Use from the relevant technical institution
such as:
d. Katup Pengaman; d. Safety valve;
e. Bejana Tekan dan peralatan lainsejenisnya;
e. Pressure vessel and other similarequipment;
Page 8 of 19
-
8/2/2019 Dirjen Migas No 84K-1998 Pemeriksaan Keselamatan Kerja (Dwi Bahasa)
9/19
f. Peralatan Berputar (unit pompa dan unitkompresor);
f. Rotating Equipment (pump units andcompressor units);
g. Peralatan listrik; g. Electrical equipment;
h. Pesawat Angkat; h. Lifting devices;
i. Pipa Penyalur; i. Distribution pipes;
j. Struktur Anjungan Lepas Pantai; j. Offshore Platform Structure;k. Ketel Uap & Bejana, Alat bantu
Navigasi, Alat Ukur dan Metering, Alat
Timbang, Helideck, Zat Radio Aktif,
Bahan Peledak, dan lain-lain;
k. Steam Boiler & Steam Vessel,Navigation Devices, Measuring Devices
& Metering, Weighting Devices,
Helideck, Radioactive Materials,
Explosives, etc.;
l. Peralatan penyelamatan dan pelindungperorangan.
l. Individual Safety and ProtectionEquipment.
3. Khusus Instalasi pemboran wajib dilakukanpemeriksaan berkala sesuai denganPedoman Pelaksanaan Pemboran Darat dan
Lepas Pantai Yang Aman di Indonesia (KK-
01-DJM).
3. Particularly for the Drilling Installation,periodic inspection shall be obligatorilycarried out pursuant to Implementative
Guidance for Safe Land and Offshore
Operation in Indonesia (KK-01-DJM).
4. Pemeriksaan Pre-Commissioning,Commissioning dan Pengujian.
4. Pre-Commissioning, Commissioning andTesting Inspection.
A. Pelaporan B.Reporting
Menyusul seluruh hasil pemeriksaan teknis
berbentuk dokumen untuk diserahkan keDirektur Direktorat Teknik Pertambangaan
Minyak dan Gas Bumi sebagai bahan evaluasi
untuk penerbitan Sertifikat Kelayakan
Penggunaan Instansi.
To prepare all results of technical inspection in
the form of documents to be submitted to the
Director of the Directorate of Oil and gas Mining
Techniques as evaluation materials for theissuance of Installation Worthiness Certificate.
II. Pemeriksaan Keselamatan kerja atas Peralatan I. Work Safety Inspection of Equipment
A. Pemeriksaan Keselamatan Kerja KatupPengaman
A.Work Safety Inspection of Safety Valve
Pemeriksaan teknis katup pengaman meliputi : Technical inspection OF safety valve includes:
a. Penelaahan Dokumen c. Review of Documents
P & ID (Piping & Instrumen Diagram) P & ID (Piping & Instrument Diagram)
Dokumen katup pengaman Safety valve documents
Plat nama Name plates
Tipe katup pengaman Types of safety valve:
Konvensional Conventional
Pilot Pilot
Balance Balance
Sertifikat Kelayakan Penggunaan test bench Worthiness Certificate for test bench
Rekaman Kalibrasi presure gauge/indicator Calibration Records for pressure gauge/
indicator Perhitungan tekanan uji cold diff untuk Calculation of cold diff. testing pressure to
Page 9 of 19
-
8/2/2019 Dirjen Migas No 84K-1998 Pemeriksaan Keselamatan Kerja (Dwi Bahasa)
10/19
menentukan tekanan buka nyata determine real open pressure
a. Pelaksanaan pengujian a. Implementation of testing
Uji tekanan buka Open pressure test
Uji bojor Leakage test
b. Rekaman Hasil Uji b. Records of Test Results
Rekaman hasil uji diisi berdasarkan dokumen
katup pengaman, data plat nama serta data
pengujian sebagai bahan evaluasi penertiban
Sertifikat Kelayakan Penggunaan Peralatan.
Records of test are completed pursuant to the
documents of safety valve, data of name plate
and data of testing as evaluation materials for the
issuance of Equipment Worthiness Certificate.
c. Penyegelan d. Sealing
Penyegelan katup pengaman dilakukan oleh
Pelaksana Inspeksi Tambang pada pengatur
katup pengaman yang telah diuji dengan hasil
baik dengan menggunakan Segel Migas.
Sealing of safety valve shall be carried out by the
Mine Inspector in the controller of safety valve
already tested with good results using Oil and gas
seal.
B. Pemeriksaan Keselamatan Kerja Bejana Tekan
dan Sejenisnya
A.Work Safety Inspection of Pressure Vessel and
Similar Equipment
Pemeriksaan Teknis bejana tekan dan sejenisnya
dibedakan menjadi 3 (tiga) bagian :
Technical inspection of pressure vessel and similar
equipment shall be differentiated into 3 (three) parts:
1. Bejana tekan dan sejenisnya yang baru dan atauakan dipasang.
2. Pressure vessel and its new similar equipmentand or those to be installed.
2. Bejana tekan dan sejensinya yang lama dan atautelah dipasang.
3. Pressure vessel and its old similar equipment andor those to be installed.
3. Bejana tekan dan sejenisnya yang mengalamireparasi/alterasi/modifikasi.
4. Pressure vessel and its similar equipmentexperiencing any
reparation/alteration/modification.
A.1 Pemeriksaan teknis bejana tekan dansejenisnya yang baru dan atau akan dipasang
C.1 Technical inspection of pressure vessel and itsnew similar equipment and or those to be
installed.
a. Penelaahan data yang meliputi : a. Review of data covers:
Gambar konstruksi dan perhitunganbejana takan;
Construction drawing and calculationof pressure vessel;
Spesifikasi material yang digunakan; Specification of materials to be used;
Spesifikasi prosedur las dan rekanankualifikasi prosedur serta catatan
kualifikasi (sertifikat) unjuk kerjajuru / operator las;
Specification of welding proceduresand procedure qualification records
and qualification notes (certificates)of welder/welding operator
performance;
Prosedur uji tidak merusak dankualifikasi personilnya;
Non-destructive procedures andpersonal qualification;
Prosedur reparasi; Reparation procedures;
Prosedur perlakuan panas pasca las(bila diisyaratkan);
Post-welding heat treatmentprocedures (if required);
Prosedur uji tekan; Pressure testing procedures;
b. Pemeriksaan fisik yang meliputi : b. Physical inspection covers;
Verifikasi sistem pengendalian mutu
manufaktur; Verification of manufacturing quality
control system;
Page 10 of 19
-
8/2/2019 Dirjen Migas No 84K-1998 Pemeriksaan Keselamatan Kerja (Dwi Bahasa)
11/19
Identifikasi material yang akandigunakan;
Identification of materials to be used;
Verifikasi pembentukan bejana; Verification of formation of vessels;
Verifikasi pemasangan sambungan; Verification of joint installation;
Verifikasi persiapan pengelasan; Verification of welding preparation;
Pemeriksaan hasil las serta verifikasi
hasil uji coba tanpa merusak; Inspection of welding results and
verification of results non-destructive
testing;
Pengukuran dimensi bejana danpemeriksaan internal;
Measurement of vessel dimensionsand internal inspection;
Uji bocor dan uji tekan. Leakage and pressure tests;
Verifikasi formulir pemanufaktur danplat nama bejana.
Verification of manufacturing formand name plate of vessel.
a. Uji Tekanan : b. Pressure test:
Pemeriksaan rekaman kalibrasi alatpengukur dan alat pencatat tekatan,
termasuk daerah jangkau yangdiijinkan untuk tekanan uji yang
bersangkutan, dimana skala
penunjukkan maksimum peralatan
termaksud 1,5 - 4 kali tekanan uji.
Inspection of records of calibration ofthe measuring devices and pressure
recorders, including ranges allowedfor the corresponding testing pressure,
in which the scale of maximum
indication of the corresponding
equipment is 1.5-4 times the testing
pressure.
Uji tekan dilaksanakan denganmenaikkan tekanan secara bertahap
dan dicatat dengan alat pencatat
tekanan sampai tekanan uji yang telah
ditentukan kemudian tekanan ditahan
minimum selama 2 (dua) jam dan
setelah itu tekanan dikeluarkan secarabertahap.
Pressure test shall be carried out bygradually increasing pressure and
recorded with a pressure recorder up
to the stipulated testing pressure, then
the pressure is held for a period of
minimum 2 (two) hours and after the
pressure is gradually released.
a. Pelaporan b. Reporting
Menyusun seluruh hasil pemeriksaan teknis
berbentuk dokumen untuk diserahkan ke
Direktur Direktorat Teknik Pertambangan
Minyak dan Gas Bumi sebagai bahan
evaluasi untuk penerbitan Sertifikat
Kelayakan Penggunaan Peralatan.
To prepare all results of technical
inspection in the form of documents to be
submitted to the Director of the Directorate
of Oil and gas Mining Techniques as
evaluation materials for the issuance of
Equipment Worthiness Certificate.
A.2 Pemeriksaan teknis bejana tekan dan
sejenisnya yang lama dan atau akan dipasang
A.2 Technical inspection of pressure vessel and
its old similar equipment and or thosealready installed.
b. Penelaahan data yang meliputi : b. Review of data covers:
Sertifikat kelayakan penggunaanperalatan yang akan diperpanjang
masa berlakunya;
Equipment Worthiness Certificatethe effective period of which will
be extended;
Catatan riwayat penggunaan bejana; Historical Notes of vessel;
Gambar bangunan bejana (as builtdrawing);
Construction drawing of vessel (asbuilt drawing);
Salinan plat nama atau marka keraslainnya;
Copy of name plate or other hardmarks;
Prosedur kerja aman melakukan Safe work procedures to carry out
Page 11 of 19
-
8/2/2019 Dirjen Migas No 84K-1998 Pemeriksaan Keselamatan Kerja (Dwi Bahasa)
12/19
pemeriksaan. inspection.
a. Penelaahan data yang meliputi : b. Review of Data covers:
Pemeriksaan visual kondisi bejana; Inspection visual of vesselconditions;
Verifikasi hasil pengukuran terakhirtebal bejana yang dilakukan olehperusahaan;
Verification of results of lastmeasurement of vessel thicknesscarried out by the Company.
Melakukan pengukuran tebal bejana; Measurement of vessel thickness
Uji tidak merusak (bila diperlukan) Non-destructive testing (ifrequired)
Verifikasi hasil perhitungan sisaumur bejana.
Verification of results ofcalculation of remaining age of
vessel.
c. Pelaporan a. Reporting
Menyusun seluruh hasil pemeriksaan teknis
berbentuk dokumen untuk diserahkan keDirektur Direktorat Teknik Pertambangan
minyak dan Gas Bumi sebagai bahan
evaluasi untuk menerbitkan Sertifikat
Kelayakan. Penggunaan Peralatan.
To prepare all results of technical
inspection in the form of documents to
be submitted to the Director of theDirectorate of Oil and gas Mining
Techniques as evaluation materials to
control Equipment Worthiness
Certificates.
B.3 Pemeriksaan teknis bejana tekan dansejenisnya yang mengalami
reparasi/alterasi/modifikasi
A.3 Technical inspection of pressure vessel and itssimilar equipment experiencing
reparation/alteration/modification
c. Penalaahan Data yang meliputi : c. Data study are cover :
Sertifikat Kelayakan Penggunaan
Peralatan yang akan diterbitkan danatau diperpanjang masa berlakunya;
Equipment Worthiness Certificate to
be issued and or the effective periodof which is extended;
Catatan riwayat penggunaan bejana; Historical notes on use of vessel;
Gambar bangunan dan konstruksibejana;
Drawing of building and constructionof vessel;
Salinan plat nama atau marka keraslainnya;
Copy of name plate or other hardmarks;
Prosedur kerja aman melakukanpemeriksaan.
Safe work procedures to carry outinspection;
Prosedur reparasi/alterasi/modifikasi; Procedures for reparation/alteration/modification;
Calculation of reparation/alteration/modification;
Calculation of reparation/alteration/modification;
Spesifikasi material bahan pengganti; Specification of substitute materials;
Spesifikasi prosedur las dan rekamankualifikasi prosedur serta catatan
kualifikasi (sertifikat) unjuk kerja
juru/operator las;
Specification of welding proceduresand procedure qualification records
and qualification notes (certificate) of
welder/welding operator performance;
Prosedur uji tidak merusak dankualifikasi personilnya;
Procedures for non-destructive testingand personal qualification
Prosedur perlakuan panas pasca las(bila diisyaratkan);
Procedures for post-welding heattreatment (if required);
a. Pemeriksaan fisik yang meliputi : c. Physical inspection covers:
Page 12 of 19
-
8/2/2019 Dirjen Migas No 84K-1998 Pemeriksaan Keselamatan Kerja (Dwi Bahasa)
13/19
Verifikasi sistem pengendalian mutupemanufaktur;
Verification of manufacturing qualitycontrol system;
Identifikasi material yang akandigunakan;
Identification of materials to be used;
Verifikasi pemebentukan bejana; Verification of formation of vessel;
Verifikasi pemasangan sambungan; Verification of joint installation;
Verifikasi persiapan pengelasan; Verification of welding preparation;
Pemeriksaan hasil las serta verifikasihasil uji tanpa merusak;
Inspection of welding results andverification of results of non-
destructive tests;
Pengukuran dimensi bejana; Measurement of vessel dimensions;
Uji bocor dan uji tekan (biladiperlukan);
Leake and pressure tests (if required);
Verifikasi formulir pemanufaktur danplat nama bejana;
Verification of manufacturing formsand name plate of vessel;
Verifikasi hasil pengukuran tebalbejana yang dilakukan olehPerusahaan;
Verification of results ofmeasurement of vessel thickness thatwill be carried out by the Company;
Melakukan pengukuran tebal bejana; Measurement of vessel thickness;
Verifikasi hasil perhitungan sisaumur bejana;
Verification of results of calculationof remaining age of vessel;
a. Pelaporan a. Reporting
Menyusun seluruh hasil pemeriksaan
teknis berbentuk dokumen untuk
diserahkan ke Direktur Direktorat Teknik
Pertambangan minyak dan Gas Bumi
sebagai bahan evaluasi untuk menerbitkan
Sertifikat Kelayakan. PenggunaanPeralatan.
To prepare all results of technical
inspection in the form of documents to be
submitted to the Director of the Directorate
Oil and gas Mining Techniques as
evaluation materials for the issuance ofEquipment Worthiness Certificate.
A. Pemeriksaan Keselamatan Kerja Pesawat Angkat A. Work Safety Inspection of Lifting Devices
Pemeriksaan teknis pesawat angkat meliputi : Technical inspection of lifting devices covers:
b. Penelaahan Dokumen d. Study of Documents
1. Spesifikasi perencanaan dan tabel beban 4. Specification of planning and load table
2. Perhitungan perencanaan 5. Calculation of planning
3. Gambar perencanaan 6. Drawing of planning
4. Material yang digunakan 7. Materials to be used
5. Spesifikasi sambungan 8. Specification of joints
6. Sumber tenaga yang digunakan 9. Power sources used
7. Petunjuk operasi (Operasi Manual) 10.Operation Manual
a. Pemeriksaan fisik a. Physical inspection
6. Pemeriksaan sambungan-sambungan 1. Inspection of joints
7. Pemeriksaan kait pemegang beban 2. Inspection of load holding hook
8. Pemeriksaan bagan yang bergerak sertaberputar
3. Inspection of moving and rotating parts
Page 13 of 19
-
8/2/2019 Dirjen Migas No 84K-1998 Pemeriksaan Keselamatan Kerja (Dwi Bahasa)
14/19
9. Pemeriksaan sistem hidrolik/pneumatik4. Inspection of hydraulic / pneumatic
system
10. Pemeriksaan kondisi tali baja (wire rope)
termasuk ikatan simpul dan jumlah lilitaan.
5. Inspection of steel wire rope conditionsincluding knot binding and number of
windings
11. Verifikasi fungsi indikator-indikator 6. Verification of functions of indicators
12. Verifikasi dimensi boom 7. Verification of boom dimensions
13. Verifikasi counter weight 8. Verification of counter weight
14. Pemeriksaan persiapan pengujian 9. Inspection of testing preparation
Persiapan tempat pengujian Preparation of testing locations
Prosedur pengujian Procedures of testing
Persiapan alat uji antara lain : Preparation of testing devices such as:
Alat ukur beban (load cell) Load measuring devices (load cells)
Beban uji Testing loads
Alat-alat ukur lainnya
Other measuring devices Operator yang sudah berkualifikasi Qualified operators
a. Pelaksanaan pengujian c. Implementation of testing
Uji fungsi tanpa beban Functional tests without load
Uji beban sesuai dengan prosedur uji bebanyang telah mendapat pengesahan Direktur
Load tests pursuant to the load testprocedures already approved by the Director.
e. Pemeriksaan setelah pengujian a. Post-testing inspection
Pemeriksaan atas seluruh bagian-bagian
terbebani dan bergerak ataupun yang diam untuk
mengetahui kemungkinan adanya deformasi,
retak, longgar pada baut dan atau cacat-cacatlainnya.
Inspection of all parts, either loaded, moving,
or standstill to know any possibility of
deformation, crack, loose bolts or other
defects.
d. Pemeriksaan khusus a. Special inspection
Apabila pesawat angkat mengalamikerusakan atau diragukan kemampuannya.
If a lifting device experiences any damageor its capacity is doubted.
Apabila diadakan perbaikan atau perubahanprinsipil pada pesawat angkat.
If any principal repair or change is doneon a lifting device.
g. Rekaman hasil uji a. Records of test results
Rekaman hasil uji diisi berdasarkan atas data
pesawat angkat dan hasil uji.
Records of test results are completed pursuant
to the data of lifting device and test results.
a. Pelaporan a. ReportingMenyusun seluruh hasil pemeriksaan teknis
berbentuk dokumen untuk diserahkan ke
Direktur Direktorat Teknik Pertambangan
minyak dan Gas Bumi sebagai bahan evaluasi
untuk menerbitkan Sertifikat Kelayakan.
Penggunaan Peralatan
To report all results of technical inspection in
the form of documents to be submitted to the
Director of the Directorate of Oil and gas
Mining Techniques as evaluation materials for
the issuance of Equipment Worthiness
Certificate.
B. Pemeriksaan Keselamatan Kerja Unit Pompa,Unit Kompresor dan Penggeraknya
B. Inspection of Work Safety of Pump Units,Compressor Units and Their Driving Force
Pemeriksaan teknis unit pompa, unit kompresor danpenggeraknya meliputi :
Technical inspection of pump units, compressorunits and their driving force covers:
Page 14 of 19
-
8/2/2019 Dirjen Migas No 84K-1998 Pemeriksaan Keselamatan Kerja (Dwi Bahasa)
15/19
a. Penilaian terhadap rancang bangun unit Pompa,unit Kompresor dan penggeraknya dengan
melaksanakan penelaahan data :
a. Evaluation of design of pump units,compressor units and their driving force by
reviewing the data:
Spesifikasi perencanaan; Specification of planning;
Gambar dan perhitungan perencanaan; Drawing and calculation of planning;
Spesifikasi material yang digunakan; Specification of materials to be used;
Spesifikasi sambungan yang digunakan; Specification of joints to be used;
Spesifikasi komponen utama dan pendukungserta piranti pengaman yang digunakan;
Specification of main and supportcomponents and safety devices used;
Pedoman pengoperasian danpemeliharaannya.
Operation and maintenance manual.
b. Penilaian pabrikasi dengan melaksanakanpenelaahan laporan inspeksi yang dilakukan oleh
Pihak Ketiga yang indenpenden di pabrik
pembuat yang terdiri dari antara lain :
a. Evaluation of fabrication by reviewing anyreports of inspection carried out by an
independent Third Party at the manufacturer's
plant consisting of:
Identifikasi material; Identification of materials;
Verifikasi pipa-pipa instrumen;
Verification of instrument pipes;
Verifikasi pengujian komponen-komponenutama;
Verification of testing of main components;
Hasil uji balancs; Results of balance tests;
Hasil pemeriksaan kelurusan (aligment)kopling dan poros/kompresor dengan
penggeraknya;
Results of alignment inspection of couplingand pump/compressor shafts with their
driving force;
Hasil "factory acceptance test" yang telahdilakukan di pabrik pembuat;
Results of "factory acceptance test" alreadycarried at the manufacturer's plant;
Pemeriksaan terhadap sistem penggeraknya. Inspection of driving force system.
c. Pemeriksaan fisik, yaitu pemeriksaan mengikutiproses pemasangan unit Pompa/unit Kompresor
dengan penggeraknya di lokasi pemasangan
dengan melakukan:
c. Physical inspection, namely inspection followingthe installation process of pump
units/compressor units with their driving force at
the installation location by carrying out:
Identifikasi peralatan komponen; Identification of equipment and components;
Pemeriksaan kondisi struktur pondasi; Inspection of structural foundationconditions;
Pemeriksaan kelengkapan alat ukur danpiranti pengaman;
Inspection of completeness of measuringdevices and safety devices;
Pemeriksaan umum kondisi pemasangan unitPompa/unit Kompresor dan penggeraknya;
General inspection installation conditions forpump units/compressor units and their
driving force;
Uji mekanikal, kelistrikan dan instrumen; Mechanical, electrical and instrumentationtests;
Uji coba piranti pengaman; Trial tests of safety devices;
Pemeriksaan pelaksanaan "start-up"; Inspection of "start-up";
Uji kemampuan. Performance tests.
d. Pelaporan d. Reporting
Menyusun seluruh hasil pemeriksaan teknis
berbentuk dokumen untuk diserahkan keDirektur Direktorat Teknik Pertambangan
To prepare all technical results of inspection in
the form of documents to be submitted to theDirector of the Directorate of Oil and gas Mining
Page 15 of 19
-
8/2/2019 Dirjen Migas No 84K-1998 Pemeriksaan Keselamatan Kerja (Dwi Bahasa)
16/19
minyak dan Gas Bumi sebagai bahan evaluasi
untuk menerbitkan Sertifikat Kelayakan.
Penggunaan Peralatan
Techniques as evaluation materials for the
issuance of Equipment Worthiness Certificate.
E. PEMERIKSAAN KESELAMATAN KERJA
PIPA PENYALUR
E. WORK SAFETY INSPECTION
DISTRIBUTION PIPES
Pemeriksaan teknis pipa penyalur meliputi : Technical inspection of distribution pipes covers:
a. Penelaahan Dokumen : a. Study of Documents:
Umum General
0. Lokasi 1. Location
0. Jadwal penyelesaian pembangunan 2. Construction completion schedule
0. Spesifikasi perencanaan 3. Specification of planning
0. Spesifikasi prosedur las dan rekamankualifikasi prosedur serta catatan
kualifikasi (sertifikat) unjuk kerja
juru/operator las
4. Specification of welding procedures andprocedure qualification records and
qualification notes (certificates) for the
performance of welder/welding operator
0. Prosedur reparasi 5. Procedures of reparation
0. Spesifikasi material yang digunakan 6. Specification of materials used
0. Prosedur pengoperasian danpemeliharaan
7. Operation and maintenance procedures
0. Prosedur pembersihan dan pengeringan 8. Cleaning and drying procedures
0. Data Piranti pengaman 9. Data of safety devices
a. Rancang bangun a. Construction
1. Penelaahan peta jalur bentang pipa penyalurantara lain :
0. Study of map of distribution pipes such as:
Kedalaman letak pipa penyalur
maksimum dan minimum (khusus pipa
penyalur lepas pantai)
Depth of maximum and minimum
distribution pipes (particularly offshore
distribution pipes)
Sudut kemiringan Inclination angle
Keadaan perparitan Depth of ditch
Jarak bentangan maksimum yangtersangga
Maximum span distance with support
Right of Way (ROW) Right of Way (ROW)
2. Penelaahan metode pelengkungan pipa dilokasi meliputi:
2. Study of pipe bending method in the location
covers:
diameter pipa
Pipe diameter
ketebalan pipa Pipe thickness
radius lengkung pipa Pipe bending radius
3. Penelaahan beban pipa penyalur : 3. Study of distribution pipe loads :
Beban operasi antara berat sendiri,tekanan internal dan eksternal,ekspansi
panas, daya apung dan lain-lain.
Operation loads such as own weight,internal and external pressures, heat
expansion, floating power, etc.
Beban lingkungan antara laingelombang, arus, angin, gempa dam
lain-lain.
Environmental loads such as wave,current, wind, earthquake etc.
Beban pemasangan antara lain
buckling, residual stress yang terjadi Installation loads such as buckling,
residual stresses occurring during pipe
Page 16 of 19
-
8/2/2019 Dirjen Migas No 84K-1998 Pemeriksaan Keselamatan Kerja (Dwi Bahasa)
17/19
saat instalasi pipa. installation.
4. Penelaahan perhitungan perhitungankekuatan pipa penyalur antara lain :
4. Study of calculation of distribution pipe
power such as:
Tegangan yang terjadi pada pipapenyalur, buckling, on bottom stability(khusus pipa penyalur lepas pantai)
Stress occurring in the distributionpipes, Buckling, on bottom stability(particularly offshore distribution pipes)
Perhitungan penyangga pipa penyalur
Calculation of distribution pipe support
Perhitungan tekanan uji yang akandilakukan.
Calculation of testing pressure to becarried out.
5. Penelaahan perhitungan pengendalian korosiantara lain:
5. Study of calculation of corrosion control
such as:
Karateristik korosi Characteristics of corrosion
Metode pengendalian korosi Corrosion control methods
Spesifikasi dan dimensi coating Specification and dimensions of coating
Kebutuhan pengendalian korosi yang
diperlukan Corrosion control needs
6. Penelaahan pada fasilitas terkait dan sisteminstrumentasi antara lain :
6. Study of relevant facilities and
instrumentation system such as:
Sistem pipa terkait seperti riser, piglauncher, pig receiver,sistem metering
dan lain-lain
Relevant pipe system such as riser, piglauncher, pig receiver, metering system,
etc.
Stasiun penguat Reinforcing station
Sistem instrumentasi seperti sistempenghentian darurat, katup pengaman
dan lain-lain.
Instrumentation system such asemergency termination system, safety
valve, etc.
7. Penelaahan surat persetujuan ataurekomendasi dari instansi yang berwenang
untuk program pengelolaan dan pemantauan
lingdungan lingkungan.
7. Study of letter of approval orrecommendation from the authorized
institution for the environmental
management and monitoring programs.
8. Penelaahan data rencana operasi 8. Study of data of operation plans
Penggunaan (service) Use (service)
Specific grafity Specific gravity
Tekanan normal masuk Inlet normal pressure
Tekanan normal keluar Outlet normal pressure
Tekanan operasi maksimum Maximum operation pressure
Temperatur operasi Operation temperature
Laju aliran operasi Operation flow rate
c. Pemeriksaan fisik meliputi : c. Physical inspection covers:
Identifikasi material yang akan digunakan; Identification of materials to be used;
Pemeriksaan lokasi jalur pipa penyalur untukmemastikan klasifikasi area, tipe konstruksi
dari jarak aman yang tersedia;
Inspection of location of distribution piperoutes to confirm classification area, type of
construction and safe distance average;
Pemeriksaan persiapan pengelasan dankesamaan sumbu serta kelurusan sambunganpipa;
Inspection of welding preparation andsimilarity of axis and alignment of pipejoints;
Pemeriksaan sistem penyangga dan Inspection of support and ditch system;
Page 17 of 19
-
8/2/2019 Dirjen Migas No 84K-1998 Pemeriksaan Keselamatan Kerja (Dwi Bahasa)
18/19
perparitan;
Penelaahan hasil uji tidak merusak; Study of results of non-destructive test;
Kondisi dan rekaman hasil uji sistempengendalian korosi serta pemberat pipa
(khusus pipa penyalur lepas pantai);
Conditions and records of test results ofcorrosion control system and pipe weightier
(particularly offshore distribution pipes);
Pemeriksaan pelaksanaan pembersihan danpengeringan dalam pipa penyalur;
Inspection of cleaning and drying indistribution pipes;
Pemeriksaan kelengkapan piranti pengaman; Inspection of completeness of safety devices;
d. Pemeriksaan pelaksanaan uji tekan d. Inspection implementation of pressure test
Kelengkapan peralatan uji yang terdiri dari : Completeness of testing equipment consisting of:
Deat weight tester (DWT) Dead weight tester (DWT)
Pengukuran tekanan Pressure measuring device
Pengukuran temperatur Temperature measuring device
Pencatat tekanan (pressure recorder) Pressure recorder
Perekam Temperatur
Temperature recorder
Pompa Pump
Alat pengukur dan pencatat tersebut harus
dikalibrasi sebelum digunakan, dan skala
penunjukkan maksimumnya adalah 1,5 - 4 kali
tekanann uji.
Measuring devices and recorders must be
calibrated before use, and the scale of maximum
indication shall be 1.5-4 times the testing
pressure.
e. Uji tekan e. Pressure test
Uji tekan dilaksanakan dengan menaikkan
tekanan secara bertahap sampai dengan tekanan
uji dan ditahan mikimum selama 24 (dua puluh
empat) jam untuk pipa penyalur didarat,
mikimum 8(delapan) jam untuk pipa penyalurdilepas pantai dan mikimum 2 (dua) jam untuk
pipa penyalur uap panas bumi.
Pressure test shall be carried out by gradually
raising the pressure up to the testing pressure and
maintained minimum for 24 (twenty-four) hours
for distribution pipes on land, minimum for 8
(eight) hours for office-shore distribution pipesand minimum for 2 (two) hours for geothermal
steam distribution pipes.
f. Pelaporan f. Reporting
Menyusun seluruh hasil pemeriksaan teknis
berbentuk dokumen untuk diserahkan ke
Direktur Dirkloret Teknik Pertambangan Minyakdan Gas Bumi sebagai bahan evaluasi untuk
penerbitan Sertifikat Kelayakan Penggunaan
Peralatan.
To prepare all results of technical inspection in
the form of documents to be submitted to the
Director of the Directorate of Oil and gas Mining
Techniques as evaluation materials for the
issuance of Equipment Worthiness Certificate.
F. Pemeriksaan Keselamatan Kerja Unit PowerGenerator, Unit Transformer, Unit Switchgear
dan Unit Motor Control Center
F. Work Safety Inspection for Power Generator,Transformer, Switchgear and Motor Control
Center Units
Pemeriksaan teknis Peralatan Listrik meliputi : Technical inspection of Electrical Equipment covers:
a. Penelaahan Dokumen a. Study of Documents
Standar yang digunakan Standards to be used
Spesifikasi unit peralatan listrik/data sheet(generator, transformer, switchgear dan
motor control center);
Specification of electrical equipment unit /data sheet (Generator, Transformer,
Switchgear and Motor Control Center);
Gambar perencanaan; Drawing of planning;
Page 18 of 19
-
8/2/2019 Dirjen Migas No 84K-1998 Pemeriksaan Keselamatan Kerja (Dwi Bahasa)
19/19
Spesifikasi perencanaan dan konstruksi; Specification of planning & construction;
Spesifikasi material; Specification of materials;
Perhitungan perencanaan (bila disyaratkan); Calculation of planning (if required);
Prosedur pengoperasian & pemeliharaan; Operation & maintenance procedures;
Klasifikasi area; Classification of area;
Piranti pengaman;
Klas isolasi; Isolation classes
b. Pemeriksaan fisik meliputi : b. Physical inspection covers:
Pemeriksaan peralatan dan komponennya Inspection of equipment and its componen
Verifikasi plat nama Verification of name plate
Pemeriksaan umum kondisi pemasangan dilokasi
General inspection of installation conditionsin the location
Pemeriksaan lay out peralatan dan areaklasifikasi
Inspection of lay out of equipment andclassification area
Pemeriksaan panel kendali
Inspection of control panel
Pemeriksaan terminal kabel utama danpenetralan
Inspection of main cable terminal andneutralization
c. Pengujian meliputi : c. Testing covers:
Pengujian ketahanan isolasi Testing of isolation resistance
Pengujian panel kendali Testing of control panel
Pengujian Hi-pot kabel Testing of Hi-pot cable
Setting relay pengaman Setting of safety relay
Pengujian sinkronisasi Testing of synchronization
Pengujian automatic start unit emergency Testing of automatic start of emergency unit
Pengujian tanpa beban dan dengan beban Testing without load and with load
Penilaian penerimaan (test value) Evaluation of acceptance (test values)
Pre-commisioning dan Commissioning Pre-commissioning and Commissioning
d. Pelaporan d. Reporting
Menyusun seluruh hasil pemeriksaan teknis
berbentuk dokumen untuk diserahkan ke
Direktur Direktorat Teknik Pertambangan
Minyak dan Gas Bumi sebagai bahan evaluasiuntuk penerbitan Sertifikat Kelayakan
Penggunaan Peralatan.
To prepare all results of technical inspection in
the form of documents to be submitted to the
Director of the Directorate of Oil and gas Mining
Techniques as evaluation materials for theissuance of Equipment Worthiness Certificate.
Ditetapkan di Jakarta Stipulated in Jakarta
Pada tanggal 19 Agustus 1998 On,August 19 1998
Direktur Jendral Minyak dan Gas Bumi Director General of Oil and gas
Soepraptono Soeleiman Soepraptono Soeleiman