Post on 26-Feb-2023
SERVICE MANUAL LEVEL 2
• For INSTRUCTION MANUAL, refer to separate file (992995271.pdf).• For MECHANISM ADJUSTMENTS, refer to the “DV MECHANICAL ADJUSTMENT MANUAL
J MECHANISM ” (9-929-807-11).
Link
SERVICE NOTE
DISASSEMBLY
BLOCK DIAGRAMS
FRAME SCHEMATIC DIAGRAMS
SCHEMATIC DIAGRAMS
PRINTED WIRING BOARDS
ADJUSTMENTS
REPAIR PARTS LIST
SPECIFICATIONS
SERVICE NOTE
DISASSEMBLY
BLOCK DIAGRAMS
FRAME SCHEMATIC DIAGRAMS
SCHEMATIC DIAGRAMS
PRINTED WIRING BOARDS
ADJUSTMENTS
REPAIR PARTS LIST
SPECIFICATIONS
Link
Revision HistoryRevision History
Ver 1.3 2004. 09
On the VC-280 boardThis service manual provides the information that is premised the circuit board replacement service and not intended repairinside the VC-280 board.Therefore, schematic diagram, printed wiring board, waveforms, mounted parts location and electrical parts list of the VC-280board are not shown.The following pages are not shown.
Schematic diagram .............................Pages 4-37 to 4-66Printed wiring board ............................Pages 4-85 to 4-88Waveforms ........................................... Page 4-92
Mounted parts location .............................Pages 4-95 to 4-96Electrical parts list ................................... Pages 6-19 to 6-24
US ModelCanadian Model
DCR-TRV18
AEP ModelUK Model
East European ModelNorth European Model
DCR-TRV16E/TRV18E/TRV116E/TRV118E
E ModelHong Kong Model
DCR-TRV16/TRV16E/TRV18/TRV18E
Australian ModelChinese Model
DCR-TRV16E/TRV18E
Tourist ModelDCR-TRV18/TRV18E
Korea ModelDCR-TRV16/TRV18J MECHANISM
DCR-TRV16/TRV16E/TRV18/TRV18E/TRV116E/TRV118E
RMT-814
Photo : DCR-TRV18
DIGITAL VIDEO CAMERA RECORDER
— 2 —
DCR-TRV16/TRV16E/TRV18/TRV18E/TRV116E/TRV118E
SPECIFICATIONS
COVERCOVER
Video camerarecorder
System
Video recording system2 rotary headsHelical scanning systemAudio recording systemRotary heads, PCM systemQuantization: 12 bits (Fs 32 kHz,stereo 1, stereo 2), 16 bits(Fs 48 kHz, stereo)
Video signal
PAL colour, CCIR standardsUsable cassetteMini DV cassette with the mark printedTape speedSP: Approx. 18.81 mm/sLP: Approx. 12.56 mm/sRecording/playback time(using cassette DVM60)SP: 1 hourLP: 1.5 hoursFastforward/rewind time(using cassette DVM60)When using the battery pack:Approx. 2 min. and 30 secondsWhen using the AC power adaptor:Approx. 2 min. and 30 secondsViewfinderElectric viewfinder (colour)Image device
DCR-TRV16E/TRV116E:4.5 mm (1/4 type) CCD (ChargeCoupled Device)Gross: Approx. 800 000 pixelsEffective:Approx. 400 000 pixels
DCR-TRV18E/TRV118E:4.5 mm (1/4 type) CCD (ChargeCoupled Device)Gross: Approx. 800 000 pixelsEffective (still):Approx. 400 000 pixelsEffective (moving):Approx. 400 000 pixelsLensCarl ZeissCombined power zoom lensFilter diameter30 mm (1 3/16 in.)10× (Optical), 120× (Digital)
Focal length
DCR-TRV16/TRV18:NTSC color, EIA standardsDCR-TRV16E/TRV18E/TRV116E/TRV118E:
3.3 – 33 mm (5/32 – 1 5/16 in.)When converted to a 35 mm stillcameraIn CAMERA/MEMORY(DCR-TRV18/TRV18E/TRV118E only) 42 – 420 mm (1 11/16 – 16 5/8 in.)Colour temperatureAuto, HOLD (Hold), nIndoor(3 200 K), Outdoor (5 800 K)Minimum illumination5 lx (lux) (F 1.7)0 lx (lux) (in the NightShot mode)** Objects unable to be seen due to
the dark can be shot with infraredlighting.
Input/Output connectors
S video input/output
DCR-TRV116E/TRV118E:4-pin mini DINLuminance signal: 1 Vp-p, 75 Ω(ohms), unbalancedChrominance signal: 0.3 Vp-p,75 Ω (ohms), unbalancedS video outputDCR-TRV16E:AEP, UK, EE, NE/TRV18E:AEP, UK, EE, NE:4-pin mini DINLuminance signal: 1 Vp-p, 75 Ω(ohms), unbalancedChrominance signal: 0.3 Vp-p,75 Ω (ohms), unbalancedAudio/Video input/outputDCR-TRV16/TRV16E:E, HK, AUS, CH/TERV18/TRV18E:E, HK, JE, AUS, CH/TRV116E/TRV118E:AV MINI JACK, 1 Vp-p, 75 Ω(ohms), unbalanced, sync negative327 mV, (at output impedancemore than 47 kΩ (kilohms))Output impedance with less than2.2 kΩ (kilohms)/Stereo minijack(ø 3.5mm)Input impedance more than47 kΩ (kilohms)Audio/Video outputDCR-TRV16E:AEP, UK, EE, NE/TRV18E:AEP, UK, EE, NE:AV MINI JACK, 1 Vp-p, 75 Ω(ohms), unbalanced, sync negative327 mV, (at output impedancemore than 47 kΩ (kilohms))Output impedance with less than2.2 kΩ (kilohms)/Stereo minijack(ø 3.5mm)Input impedance more than47 kΩ (kilohms)
DV input/outputDCR-TRV16/TRV16E:E, HK, AUS, CH/TERV18/TRV18E:E, HK, JE, AUS, CH/TRV116E/TRV118E:4-pin connectorDV outputDCR-TRV16E:AEP, UK, EE, NE/TRV18E:AEP, UK, EE, NE:4-pin connectorHeadphone jackStereo minijack (ø 3.5 mm)USB jackmini-BLANC jackStereo mini-minijack (ø 2.5 mm)MIC jackStereo minijack (ø 3.5 mm)
LCD screen
Picture6.2 cm (2.5 type)50.3 × 37.4 mm (2 × 1 1/2 in.)Total dot number123 200 (560 × 220)
DCR-TRV16:4.5 mm (1/4 type) CCD (ChargeCoupled Device)Gross: Approx. 680 000 pixelsEffective :Approx. 340 000 pixels
DCR-TRV18:4.5 mm (1/4 type) CCD (ChargeCoupled Device)Gross: Approx. 680 000 pixelsEffective (still):Approx. 340 000 pixelsEffective (moving):Approx. 340 000 pixels
4-pin mini DI
DCR-TRV16/TRV16E:E, HK, AUS, CH/TERV18/TRV18E:E, HK, JE, AUS, CH/TRV116E/TRV118E:
NLuminance signal: 1 Vp-p, 75 Ω(ohms), unbalancedChrominance signal: 0.286 Vp-p,75 Ω (ohms)
General
Power requirements7.2 V (battery pack)8.4 V (AC power adaptor)Average power consumption(when using the battery pack)During camera recording usingLCD3.3 WViewfinder2.5W Operating temperature0°C to 40°C (32°F to 104°F)Storage temperature–20°C to + 60°C(–4°F to + 140°F)Dimensions (Approx.)76 × 93 × 162 mm(3 × 3 3/4 × 6 1/2 in.)(w/h/d)Mass (approx.)DCR-TRV16/TRV16E/TRV116E:610 g (1 lb 5 oz)DCR-TRV18/TRV18E/TRV118E:620 g (1 lb 5 oz)main unit onlyDCR-TRV16/TRV16E/TRV116E:700 g (1 lb 8 oz)DCR-TRV18/TRV18E/TRV118E:710 g (1 lb 9 oz)including the battery packcassette DVM60 and lens capSupplied accessoriesSee page 3.
AC power adaptor
Power requirements100 – 240 V AC, 50/60 HzPower consumption23 WOutput voltageDC OUT: 8.4 V, 1.5 A in theoperating modeOperating temperature0°C to 40°C (32°F to 104°F)Storage temperature–20°C to + 60°C (–4°F to + 140°F)Dimensions (approx.)125 × 39 × 62 mm(5 × 1 9/16 × 2 1/2 in.) (w/h/d)excluding projecting partsMass (approx.)280 g (9.8 oz)excluding mains lead
Battery pack
NP-FM30Maximum output voltageDC 8.4 VOutput voltageDC 7.2 VCapacity5.0 Wh (700 mAh)Dimensions (approx.)38.2 × 20.5 × 55.6 mm(1 9/16 × 13/16 × 2 1/4 in.)(w/h/d)Mass (approx.)65 g (2.3 oz)TypeLithium ion
“Memory Stick”(except DCR-TRV16/TRV16E/TRV116E)
MemoryFlash memory8 MB: MSA-8AOperating voltage2.7 – 3.6 VPower consumptionApprox. 45 mA in the operatingmodeApprox. 130 µA in the standbymodeDimensions (approx.)50 × 2.8 × 21.5 mm(2 × 1/8 × 7/8 in.) (w/h/d)Mass (approx.)4 g (0.14 oz)
Design and specifications aresubject to change without notice.
• AbbreviationEE : East European modelNE : North European modelHK : Hong Kong model
AUS : Australian modelCH : Chinese modelJE : Tourist model
— 3 —
DCR-TRV16/TRV16E/TRV18/TRV18E/TRV116E/TRV118E
1. Check the area of your repair for unsoldered or poorly-solderedconnections. Check the entire board surface for solder splashesand bridges.
2. Check the interboard wiring to ensure that no wires are"pinched" or contact high-wattage resistors.
3. Look for unauthorized replacement parts, particularlytransistors, that were installed during a previous repair. Pointthem out to the customer and recommend their replacement.
4. Look for parts which, through functioning, show obvious signsof deterioration. Point them out to the customer andrecommend their replacement.
5. Check the B+ voltage to see it is at the values specified.6. Flexible Circuit Board Repairing
• Keep the temperature of the soldering iron around 270˚Cduring repairing.
• Do not touch the soldering iron on the same conductor of thecircuit board (within 3 times).
• Be careful not to apply force on the conductor when solderingor unsoldering.
Unleaded solderBoards requiring use of unleaded solder are printed with the lead-free mark (LF) indicating the solder contains no lead.(Caution: Some printed circuit boards may not come printed withthe lead free mark due to their particular size.)
: LEAD FREE MARKUnleaded solder has the following characteristics.• Unleaded solder melts at a temperature about 40°C higher than
ordinary solder.Ordinary soldering irons can be used but the iron tip has to beapplied to the solder joint for a slightly longer time.Soldering irons using a temperature regulator should be set toabout 350°C.Caution: The printed pattern (copper foil) may peel away if theheated tip is applied for too long, so be careful!
• Strong viscosityUnleaded solder is more viscous (sticky, less prone to flow) thanordinary solder so use caution not to let solder bridges occur suchas on IC pins, etc.
• Usable with ordinary solderIt is best to use only unleaded solder but unleaded solder mayalso be added to ordinary solder.
SAFETY CHECK-OUT
After correcting the original service problem, perform the following
safety checks before releasing the set to the customer.
SAFETY-RELATED COMPONENT WARNING!!
COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE WITHMARK 0 ON THE SCHEMATIC DIAGRAMS AND IN THE PARTSLIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESECOMPONENTS WITH SONY PARTS WHOSE PART NUMBERSAPPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTSPUBLISHED BY SONY.
ATTENTION AU COMPOSANT AYANT RAPPORTÀ LA SÉCURITÉ!
LES COMPOSANTS IDENTIFÉS PAR UNE MARQUE 0 SUR LESDIAGRAMMES SCHÉMATIQUES ET LA LISTE DES PIÈCES SONTCRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NEREMPLACER CES COMPOSANTS QUE PAR DES PIÈSES SONYDONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL OUDANS LES SUPPÉMENTS PUBLIÉS PAR SONY.
CAUTION :Danger of explosion if battery is incorrectly replaced.Replace only with the same or equivalent type.
— 4 —
DCR-TRV16/TRV16E/TRV18/TRV18E/TRV116E/TRV118E
• SUPPLIED ACCESSORIESMake sure that the following accessories are supplied with your camcorder.
1Wireless Remote Commander (1)
2AC-L10A/L10B/L10C AC power adaptor (1),Mains lead (1)
3 R6 (size AA) battery for RemoteCommander (2)
4 Battery pack (1)
5A/V connecting cable (1)
6 Shoulder strap (1)
7 Lens cap (1)
8 “Memory Stick” (1)(DCR-TRV18/TRV18E/TRV118E)
9USB cable (1)
0 CD-ROM (1)SPVD-008 (I) USB Driver (DCR-TRV18 : US/CND model only)SPVD-008 USB Driver (except : DCR-TRV18: US/CND model)
qa 21-pin adaptor (1)
8
1 2
4 75 6
3
9
qs qd
0 qa
qs 2-pin conversion adaptor (1)(DCR-TRV18 : JE/TRV18E : JE model only)
(for European model only)
qd 2-pin conversion adaptor (1)(DCR- TRV16 : E, HK/TRV16E : E, HK/
TRV18 : E, HK/TRV18E : E, HK)
DCR-TRV16
E, HK, KR
NTSC
a
IN/OUT
IN/OUT
DCR-TRV16E
PAL
• AbbreviationCND : Canadian modelEE : East European modelNE : North European modelHK : Hong Kong model
Table for difference of function
Model
Destination
Color System
VTR REC
Memory Stick
DV Terminal
AUDIO/VIDEOTerminal
Intelligent AccessoryShoe
AEP, UK,EE, NE
OUT
OUT
DCR-TRV18
US, CND, E,HK, JE, KR
NTSC
DCR-TRV18E
E, HK, AUS,CH
AEP, UK,EE, NE
E, HK, AUS,JE, CH
a
a
8-pin connector 15-pin connector
DCR-TRV116E
AEP, UK,EE, NE
DCR-TRV118E
AEP, UK,EE, NE
8-pinconnector
15-pinconnector
a
a
PAL
AUS : Australian modelCH : Chinese modelJE : Tourist modelKR : Korea model
IN/OUT
IN/OUT
OUT
OUT
IN/OUT
IN/OUT
— 5 —
DCR-TRV16/TRV16E/TRV18/TRV18E/TRV116E/TRV118E
TABLE OF CONTENTS1. SERVICE NOTE1-1. SERVICE NOTE ·····························································1-11. POWER SUPPLY DURING REPAIRS ··························1-12. TO TAKE OUT A CASSETTE WHEN NOT EJECT
(FORCE EJECT) ·····························································1-11-2. SELF-DIAGNOSIS FUNCTION ····································1-21. SELF-DIAGNOSIS FUNCTION ····································1-22. SELF-DIAGNOSIS DISPLAY ·······································1-23. SERVICE MODE DISPLAY ··········································1-23-1. Display Method ·······························································1-23-2. Switching of Backup No. ················································1-23-3. End of Display ·································································1-24. SELF-DIAGNOSIS CODE TABLE ································1-3
2. DISASSEMBLY2-1. LCD SECTION (PD-161 BOARD) ································2-32-2. EVF SECTION (LB-077 BOARD) ·································2-42-3. FRONT PANEL SECTION ·············································2-52-4. MA-409, FB-219 BOARDS ············································2-62-5. TOP CABINET ASSEMBLY ·········································2-72-6. CABINET (R) SECTION ···············································2-72-7. BATTERY PANEL SECTION ········································2-82-8. EVF SECTION ································································2-82-9. LB-077 BOARD ······························································2-92-10. VA-117 BOARD (1) ······················································ 2-102-11. MAIN CHASSIS COMPLETE SECTION ··················· 2-112-12. VA-117 BOARD (2) ······················································ 2-122-13. VC-280 BOARD ··························································· 2-122-14. LENS SECTION ··························································· 2-132-15. MECHANISM DECK ··················································· 2-132-16. JK-217, JK-218 BOARDS ············································2-142-17. CD-365 BOARD, 650A (CZ) BLOCK ASSEMBLY
(LENS DEVICE) ··························································· 2-142-18. CK-108 BOARD ··························································· 2-172-19. HINGE ASSEMBLY ·····················································2-182-20. CONTROL SWITCH BLOCK (PS-CX2670) ·············· 2-192-21. MEMORY STICK CONNECTOR ······························· 2-202-22. CIRCUIT BOARDS LOCATION ·································2-212-23. FLEXIBLE BOARDS LOCATION ······························ 2-22
3. BLOCK DIAGRAMS3-1. OVERALL BLOCK DIAGRAM (1/4) ···························3-13-2. OVERALL BLOCK DIAGRAM (2/4) ···························3-33-3. OVERALL BLOCK DIAGRAM (3/4) ···························3-53-4. OVERALL BLOCK DIAGRAM (4/4) ···························3-73-5. POWER BLOCK DIAGRAM (1/3) ································3-93-6. POWER BLOCK DIAGRAM (2/3) ······························ 3-113-7. POWER BLOCK DIAGRAM (3/3) ······························ 3-13
4 PRINTED WIRING BOARDS ANDSCHEMATIC DIAGRAMS
4-1. FRAME SCHEMATIC DIAGRAM (1/3) ·······················4-1FRAME SCHEMATIC DIAGRAM (2/3) ·······················4-3FRAME SCHEMATIC DIAGRAM (3/3) ·······················4-5
4-2. SCHEMATIC DIAGRAMS ············································4-9• CD-365 (CCD IMAGER)
SCHEMATIC DIAGRAM ······························4-9• LB-077 (EVF, EVF BACK LIGHT)
SCHEMATIC DIAGRAM ····························4-10• MA-409 (MIC IN, HP JACK, REMOTE CONTROLRECEIVER, SWITCH)
SCHEMATIC DIAGRAM ····························4-11• FB-219 (MANUAL FOCUS SENSOR)
SCHEMATIC DIAGRAM ····························4-11• JK-217 (STEADY SHOT, A/D IN/OUT)
SCHEMATIC DIAGRAM ····························4-13
• JK-218 (DIGITAL IN/OUT)SCHEMATIC DIAGRAM ····························4-13
• CK-108 (SWITCH, CONNECTOR)SCHEMATIC DIAGRAM ····························4-15
• CONTROL SWITCH BLOCK (PS-CX2670)SCHEMATIC DIAGRAM ····························4-17
• PD-161 (1/2) (RGB DRIVE, TIMING GENERATOR)SCHEMATIC DIAGRAM ····························4-19
• PD-161 (2/2) (LCD DRIVE, BACK LIGHT)SCHEMATIC DIAGRAM ····························4-21
• VA-117 (1/6) (RGB DRIVE, TG)SCHEMATIC DIAGRAM ····························4-23
• VA-117 (2/6) (AUDIO)SCHEMATIC DIAGRAM ····························4-25
• VA-117 (3/6) (MIC AMP)SCHEMATIC DIAGRAM ····························4-27
• VA-117 (4/6) (DC-DC CONVERTER)SCHEMATIC DIAGRAM ····························4-29
• VA-117 (5/6) (CHARGE)SCHEMATIC DIAGRAM ····························4-31
• VA-117 (6/6) (VIDEO I/O)SCHEMATIC DIAGRAM ····························4-33
• FP-100 (MODE SWITCH), FP-228 (DEW SENSOR),FP-102 FLEXIBLE (TAPE TOP/END SENSOR,S/T REEL)
SCHEMATIC DIAGRAM ····························4-35
Shematic diagram of the VC-280 board are not shown.Pages from 4-37 to 4-66 are not shown.
4-3. PRINTED WIRING BOARDS ·····································4-67• CD-365 (CCD IMAGER)
PRINTED WIRING BOARD ·······················4-67• FP-443 FLEXIBLE BOARD ·····································4-68• JK-217 (STEADY SHOT, A/D, IN/OUT),JK-218 (DIGITAL IN/OUT)
PRINTED WIRING BOARD ·······················4-69• MA-409 (MIC IN, HP JACK, REMOTE CONTROLRECEIVER, SWITCH)
PRINTED WIRING BOARD ·······················4-71• FP-444 FLEXIBLE BOARD ·····································4-71• FB-219 (MANUAL FOCUS SENSOR),PD-161 (RGB DRIVE, TIMING GENERATOR,LCD DRIVE, BACK LIGHT)
PRINTED WIRING BOARD ·······················4-73• FP-100 (MODE SWITCH), FP-228 (DEW SENSOR),FP-102 (TAPE TOP/END SENSOR, S/T REEL)
FLEXIBLE BOARD ·····································4-75• LB-077 (EVF, EVF BACK LIGHT)
PRINTED WIRING BOARD ·······················4-75• CK-108 (SWITCH, CONNECTOR)
PRINTED WIRING BOARD ·······················4-77• VA-117 (RGB DRIVE, TG, AUDIO, MIC AMP,DC-DC CONVERTER, CHARGE, VIDEO I/O)
PRINTED WIRING BOARD ·······················4-81
Printed wiring board of the VC-280 board are not shown.Pages from 4-85 to 4-88 are not shown.
4-4. WAVEFORMS ······························································ 4-89
Waveforms of the VC-280 board are not shown.Page 4-92 is not shown.
4-5. MOUNTED PARTS LOCATION ·································4-93
Mounted parts location of the VC-280 board is not shown.Pages from 4-95 to 4-96 are not shown.
— 6 —
DCR-TRV16/TRV16E/TRV18/TRV18E/TRV116E/TRV118E
5. ADJUSTMENTS1. Adjusting items when replacing main parts and boards. ·5-25-1. CAMERA SECTION ADJUSTMENT ··························· 5-41-1. PREPARATIONS BEFORE ADJUSTMENT
(CAMERA SECTION) ··················································· 5-41-1-1.List of Service Tools ························································5-41-1-2.Preparations ·····································································5-51-1-3.Precaution ········································································5-71. Setting the Switch ····························································5-72. Order of Adjustments ······················································ 5-73. Subjects ··········································································· 5-71-2. INITIALIZATION OF 8, A, B, C, D, E, F, 1B, 1F
PAGE DATA ····································································5-81-2-1. INITIALIZATION OF A, D PAGE DATA ······················ 5-91. Initializing the A, D Page Data ········································5-92. Modification of A, D Page Data ······································ 5-93. A Page Table ····································································5-94. D Page Table ··································································5-101-2-2. INITIALIZATION OF B, 1B PAGE DATA ·················· 5-111. Initializing the B, 1B Page Data ····································5-112. Modification of B, 1B Page Data ··································5-113. B Page Table ··································································5-114. 1B Page Table ································································5-111-2-3. INITIALIZATION OF 8, C PAGE DATA ·····················5-121. Initializing the 8, C Page Data ·······································5-122. Modification of 8, C Page Data ·····································5-123. 8 Page Table ···································································5-124. C Page Table ··································································5-131-2-4. INITIALIZATION OF E, F, 1F PAGE DATA ···············5-151. Initializing the E, F, 1F Page Data ·································5-152. Modification of E, F, 1F Page Data ·····································5-153. E Page Table ··································································5-164. F Page Table ··································································5-165. 1F Page Table ································································5-171-3. CAMERA SYSTEM ADJUSTMENTS ························5-191. 36MHz Origin Oscillation Adjustment (VC-280 board) 5-192. HALL Adjustment ·························································5-193. Flange Back Adjustment (Using Minipattern Box) ·······5-204. Flange Back Adjustment (Using Flange Back Adjustment
Chart and Subject More Than 500m Away) ·················· 5-214-1. Flange Back Adjustment (1) ··········································5-214-2. Flange Back Adjustment (2) ··········································5-215. Flange Back Check ························································5-226. Optical Axis Adjustment ···············································5-237. Picture Frame Setting ····················································5-248. Color Reproduction Adjustment ····································5-259. MAX GAIN Adjustment ···············································5-2610. Auto White Balance & LV Standard Data Input ···········5-2611. Auto White Balance Adjustment ···································5-2712. White Balance Check ····················································5-2813. Mechanical Shutter Adjustment ····································5-291-4. COLOR ELECTRONIC VIEWFINDER SYSTEM
ADJUSTMENT ·····························································5-301. VCO Adjustment (VA-117 board) ·································5-302. RGB AMP Adjustment (VA-117 board) ························5-313. Contrast Adjustment (VA-117 board) ····························5-314. White Balance Adjustment (VA-117 board) ·················· 5-321-5. LCD SYSTEM ADJUSTMENT ···································5-331. VCO Adjustment (PD-161 board) ·································5-332. RGB AMP Adjustment (PD-161 board) ························5-343. Contrast Adjustment (PD-161 board) ····························5-344. COM AMP Adjustment (PD-161 board) ·······················5-355. V COM Adjustment (PD-161 board) ····························5-356. White Balance Adjustment (PD-161 board) ·················· 5-365-2. MECHANISM SECTION ADJUSTMENT ·················· 5-372-1. HOE TO ENTER RECORD MODE WITHOUT
CASSETTE ···································································5-37
2-2. HOE TO ENTER PLAYBACK MODE WITHOUTCASSETTE ···································································5-37
2-3. TAPE PATH ADJUSTMENT ········································5-371. Preparation for Adjustment ···········································5-372. Processing after Completing Operations: ······················5-375-3. VIDEO SECTION ADJUSTMENTS ···························5-383-1. PREPARATIONS BEFORE ADJUSTMENTS ············5-383-1-1.Equipment Required ······················································5-383-1-2.Precautions on Adjusting ···············································5-393-1-3.Adjusting Connectors ····················································5-403-1-4.Connecting the Equipment ············································5-403-1-5.Alignment Tapes ····························································5-413-1-6. Input/Output Level and Impedance ·······························5-413-2. SYSTEM CONTROL SYSTEM ADJUSTMENT ········5-421. Initialization of 8, A, B, C, D, E, F, 1B, 1F Page Data ··5-422. Serial No. Input ·····························································5-422-1. Company ID Input ·························································5-422-2. Serial No. Input ·····························································5-423-3. SERVO AND RF SYSTEM ADJUSTMENT ···············5-441. Cap FG Duty Adjustment (VC-280 Board) ···················5-442. PLL f0 & LPF f0 Adjustment (VC-280 Board) ·············5-443. Switching Position Adjustment (VC-280 Board) ··········5-454. AGC Center Level and APC & AEQ Adjustment ·········5-454-1. Preparations before adjustments ····································5-454-2. AGC Center Level Adjustment (VC-280 Board) ··········5-454-3. APC & AEQ Adjustment (VC-280 Board) ···················5-464-4. Processing after Completing Adjustments ····················5-465. PLL f0 & LPF f0 Fine Adjustment (VC-280 Board) ····5-473-4. VIDEO SYSTEM ADJUSTMENTS ·····························5-481. Chroma BPF f0 Adjustment (VA-117 Board) ···············5-482. S VIDEO OUT Y Level Adjustment (VC-280 Board) ··5-483. S VIDEO OUT Chroma Level Adjustment
(VC-280 Board) ·····························································5-494. VIDEO OUT Y, Chroma Level Check (VC-280 Board) ·5-493-5. AUDIO SYSTEM ADJUSTMENTS ····························5-501. Playback Level Check ···················································5-512. Overall Level Characteristics Check ·····························5-513. Overall Distortion Check ···············································5-514. Overall Noise Level Check ············································5-515. Overall Separation Check ··············································5-515-4. SERVICE MODE ··························································5-524-1. ADJUSTMENT REMOTE COMMANDER ················5-521. Using the adjustment remote commander ·····················5-522. Precautions upon using the adjustment remote
commander ····································································5-524-2. DATA PROCESS ···························································5-534-3. SERVICE MODE ··························································5-541. Setting the Test Mode ····················································5-542. Emergence Memory Address ········································5-542-1. EMG Code (Emergency Code) ·····································5-542-2. MSW Code ····································································5-553. Bit value discrimination ················································5-564. Switch check (1) ····························································5-565. Switch check (2) ····························································5-566. Switch check (3) ····························································5-577. Switch check (4) ····························································5-578. Record of Use check (1) ················································5-589. Record of Use check (2) ················································5-5810. Record of Self-diagnosis check ·····································5-58
6. REPAIR PARTS LIST6-1. EXPLODED VIEWS ······················································ 6-16-1-1.OVERALL SECTION ·····················································6-16-1-2.FRONT PANEL SECTION ·············································6-26-1-3.CABINET (R) SECTION ···············································6-36-1-4.LCD SECTION ·······························································6-46-1-5.EVF SECTION ································································6-5
— 7 —
DCR-TRV16/TRV16E/TRV18/TRV18E/TRV116E/TRV118E
6-1-6.MAIN CHASSIS COMPLETE SECTION ·····················6-66-1-7.CABINET (L) SECTION ················································6-76-1-8.CASSETTE COMPARTMENT AND DRUM
BLOCK ASSEMBLY ······················································6-86-1-9.LS CHASSIS BLOCK ASSEMBLY ·······························6-96-1-10.MECHANISM CHASSIS BLOCK ASSEMBLY ······· 6-106-2. ELECTRICAL PARTS LIST ········································6-11
Parts list of the VC-280 board are not shown.Pages from 6-19 to 6-24 are not shown.
* Optical axis frame and Color reproduction frame areshown on pages 188 and 189.
1-1
DCR-TRV16/TRV16E/TRV18/TRV18E/TRV116E/TRV118E
SECTION 1SERVICE NOTE
COVERCOVER
Loading motor
DC power supply(+4.5Vdc)
VC-280 board
CN1010
1-1. SERVICE NOTE
1. POWER SUPPLY DURING REPAIRS
In this unit, about 10 seconds after power is supplied to the battery terminal using the regulated power supply (8.4V), the power is shut off sothat the unit cannot operate.This following two methods are available to prevent this. Take note of which to use during repairs.
Method 1:Use the AC power adaptor (AC-L10, AC-VQ800 etc.).
Method 1:Connect the servicing remote commander RM-95 (J-6082-053-B) to the LANC jack, and set the commander switch to the “ADJ” side.
2. TO TAKE OUT A CASSETTE WHEN NOT EJECT (FORCE EJECT)1 Refer to 2-3. to remove the front panel assembly.2 Refer to 2-5. to remove the top cabinet assembly.3 Refer to 2-6. to remove the cabinet (R) assembly.4 Refer to 2-7. to remove the battery panel section.5 Remove the EVF block.6 Open the VA-117 board.7 Disconnect CN1010 (27P, 0.3mm) of VC-280 board.8 Open the cassette lid.9 Supply +4.5V from the DC power supply to the loading motor and unload with a pressing the cassette compartment.
1-2
DCR-TRV16/TRV16E/TRV18/TRV18E/TRV116E/TRV118E
1-2. SELF-DIAGNOSIS FUNCTION
1. SELF-DIAGNOSIS FUNCTIONWhen problems occur while the unit is operating, the self-diagnosisfunction starts working, and displays on the viewfinder, LCD screenor LCD window what to do. This function consists of two display;self-diagnosis display and service mode display.Details of the self-diagnosis functions are provided in the Instructionmanual.
Note: The “self-diagnosis display” data will be kept even if the lithium battery (CK-108 board BT5201 of the cabinet (R) assembly) is removed.
2. SELF-DIAGNOSIS DISPLAYWhen problems occur while the unit is operating, the counter of theviewfinder, LCD screen or LCD window consists of an alphabetand 4-digit numbers, which blinks at 3.2 Hz. This 5-character displayindicates the “repaired by:”, “block” in which the problem occurred,and “detailed code” of the problem.
3. SERVICE MODE DISPLAYThe service mode display shows up to six self-diagnosis codes shown in the past.
3-1. Display MethodWhile pressing the “STOP” key, set the switch from OFF to “VCR”, and continue pressing the “STOP” key for 5 seconds continuously. Theservice mode will be displayed, and the counter will show the backup No. and the 5-character self-diagnosis codes.
3-2. Switching of Backup No.By rotating the control dial, past self-diagnosis codes will be shown in order. The backup No. in the [] indicates the order in which theproblem occurred. (If the number of problems which occurred is less than 6, only the number of problems which occurred will be shown.)[1] : Occurred first time [4] : Occurred fourth time[2] : Occurred second time [5] : Occurred fifth time[3] : Occurred third time [6] : Occurred the last time
3-3. End of DisplayTurning OFF the power supply will end the service mode display.
Order of previous errors
Backup No. Self-diagnosis Codes
C : 3 1 : 1 1[3]
Lights up
Viewfinder or LCD screen
[3] C : 3 1 : 1 1 3 C : 3 1 : 11LCD window
1 13 1
C : 3 1 : 11
C
Repaired by:
Refer to page 1-3.Self-diagnosis Code Table.
Indicates the appropriatestep to be taken.E.g.31 ....Reload the tape.32 ....Turn on power again.
Block Detailed Code
Blinks at 3.2Hz
C : Corrected by customerH : Corrected by dealerE : Corrected by service
engineer
Viewfinder or LCD screen LCD window
C : 3 1 : 1 1
Control dial
LCD window
1-3E
DCR-TRV16/TRV16E/TRV18/TRV18E/TRV116E/TRV118E
4. SELF-DIAGNOSIS CODE TABLE
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
E
E
E
E
BlockFunction
0 4
2 1
2 2
3 1
3 1
3 1
3 1
3 1
3 1
3 1
3 1
3 1
3 1
3 2
3 2
3 2
3 2
3 2
3 2
3 2
3 2
3 2
3 2
6 1
6 1
6 2
6 2
DetailedCode
0 0
0 0
0 0
1 0
1 1
2 0
2 1
2 2
2 3
2 4
3 0
4 0
4 2
1 0
1 1
2 0
2 1
2 2
2 3
2 4
3 0
4 0
4 2
0 0
1 0
0 0
0 1
Symptom/State
Non-standard battery is used.
Condensation.
Video head is dirty.
LOAD direction. Loading does notcomplete within specified time
UNLOAD direction. Loading does notcomplete within specified time
T reel side tape slacking when unloading.
Winding S reel fault when counting therest of tape.
T reel fault.
S reel fault.
T reel fault.
FG fault when starting capstan.
FG fault when starting drum.
FG fault during normal drum operations.
LOAD direction loading motor time-out.
UNLOAD direction loading motortime-out.
T reel side tape slacking whenunloading.
Winding S reel fault when counting therest of tape.
T reel fault.
S reel fault.
T reel fault.
FG fault when starting capstan.
FG fault when starting drum
FG fault during normal drumoperations
Difficult to adjust focus(Cannot initialize focus.)
Zoom operations fault(Cannot initialize zoom lens.)
Steadyshot function does not work well.(With pitch angular velocity sensor outputstopped.)
Steadyshot function does not work well.(With yaw angular velocity sensor outputstopped.)
Self-diagnosis Code
Rep
aire
d by
:
Correction
Use the info LITHIUM battery.
Remove the cassette, and insert it again after one hour.
Clean with the optional cleaning cassette.
Load the tape again, and perform operations from the beginning.
Load the tape again, and perform operations from the beginning.
Load the tape again, and perform operations from the beginning.
Load the tape again, and perform operations from the beginning.
Load the tape again, and perform operations from the beginning.
Load the tape again, and perform operations from the beginning.
Load the tape again, and perform operations from the beginning.
Load the tape again, and perform operations from the beginning.
Load the tape again, and perform operations from the beginning.
Load the tape again, and perform operations from the beginning.
Remove the battery or power cable, connect, and performoperations from the beginning.
Remove the battery or power cable, connect, and performoperations from the beginning.
Remove the battery or power cable, connect, and performoperations from the beginning.
Remove the battery or power cable, connect, and performoperations from the beginning.
Remove the battery or power cable, connect, and performoperations from the beginning.
Remove the battery or power cable, connect, and performoperations from the beginning.
Remove the battery or power cable, connect, and performoperations from the beginning.
Remove the battery or power cable, connect, and performoperations from the beginning.
Remove the battery or power cable, connect, and performoperations from the beginning.
Remove the battery or power cable, connect, and performoperations from the beginning.
Inspect the lens block focus reset sensor (Pin qk of CN1201 of VC-280 board) when focusing is performed when the focus ring is rotatedin the focus manual mode, and the focus motor drive circuit (IC1204of VC-280 board) when the focusing is not performed.
Inspect the lens block zoom reset sensor (Pin 9 of CN1201 ofVC-280 board) when zooming is performed when the zoom lens isoperated and the zoom motor drive circuit (IC1204 of VC-280board) when zooming is not performed.
Inspect pitch angular velocity sensor (SE5302 of JK-217 board)peripheral circuits.
Inspect yaw angular velocity sensor (SE5301 of JK-217 board)peripheral circuits.
Ver 1.2 2003. 11
2-1
SECTION 2DISASSEMBLY
DCR-TRV16/TRV16E/TRV18/TRV18E/TRV116E/TRV118E
COVERCOVER
The following flow chart shows the disassembly procedure.
2-1. LCD section (PD-161 board) PD-161 board service position
2-2. EVF section (LB-077 board)
2-3. Front panel section
LB-077 board service position
2-4. MA-409, FB-219 boards
2-5. Top cabinet assembly
2-6. Cabinet (R) section
2-7. Battery panel section
2-10. VA-117 board (1)
2-8. EVF section
2-12. VA-117 board (2)
2-13. VC-280 board
2-14. Lens section 2-15. Mechanism deck
2-16. JK-217, JK-218 boards
2-17. CD-365 board, 650A (CZ) block assembly (Lens device)
2-18. CK-108 board
2-19. Hinge assembly
2-20. Control switch block (PS-CX2670)
2-11. Main chassis complete section
MA-409 board service position
VA-117 board service position
SERVICE POSITION TO CHECK THE CAMERA SECTION
2-9. LB-077 board
(page 2-3) (page 2-3)
(page 2-7)
(page 2-14)
(page 2-19, 2-20)
2-21. Memory stick connector (TRV18/TRV18E/TRV118E) (page 2-20)
(page 2-18)
(page 2-7)
(page 2-4)
(page 2-5)
(page 2-5)
(page 2-6)
(page 2-6)
(page 2-8)
(page 2-8)
(page 2-9)
(page 2-10)(page 2-10)
(page 2-14) (page 2-16)
SERVICE POSITION TO CHECK THE VTR SECTION
(page 2-15)
(page 2-17)
(page 2-11)
(page 2-12)
(page 2-12)
(page 2-13) (page 2-13)
DC
R-T
RV
16/T
RV
16E
/TR
V18
/TR
V18
E/T
RV
116E
/TR
V11
8E
2-2
DCR-TRV16/TRV16E/TRV18/TRV18E/TRV116E/TRV118E
Adjustment remotecommander (RM-95)
AC poweradaptor AC IN
CPC-8 jig(J-6082-388-A)
CPC lid
[Equipment connection]
Screw(M1.7 × 4), lock ace, p2
2-3
DCR-TRV16/TRV16E/TRV18/TRV18E/TRV116E/TRV118E
NOTE: Follow the disassembly procedure in the numerical order given.
2-1. LCD SECTION (PD-161 BOARD)
PD-161
PD-161
B
B
A
A
7 P cabinet (c) assembly, Indication LCD block assembly
P cabinet (c) assembly
5 P cabinet (M)
8 Liquid crystal indicator module
9 Back light (Cold cathode fluorescent tube)
Back light(Cold cathode fluorescent tube)
1 Screw (M2 × 4), lock ace, p2
6 FP-441 flexible board (Indication LCD block assembly) (20P)
2 Screw (M2 × 4), lock ace, p2
0 PD-161 board, P frame assembly
3 Two screws (M2 × 4), lock ace, p2
[PD-161 BOARD SERVICE POSITION]
Liquid crystal indicator module
4 Five claws
Adjustment remotecommander (RM-95)
AC poweradaptor AC IN
CPC-8 jig(J-6082-388-A)
PD-161 board
Caution
Caution
FP-441 flexible board
The 7 P cabinet (C) assembly is securely fixed in the LCD unit by the five 4 claws. Because the Indication LCD block assembly installed in the Cabinet (C) assembly is connected to the PD-161 board with the FP-441 flexible board, the flexible board may be damaged if the Cabinet (C) assembly is removed forcibly. Be careful not to damage the flexible board.
Indication LCD block assembly
2-4
DCR-TRV16/TRV16E/TRV18/TRV18E/TRV116E/TRV118E
2-2. EVF SECTION (LB-077 BOARD)
B A
2 Two tapping screws (M1.7 × 6)
4 VF cabinet (upper) assembly
6 VF lens assembly
7 LB-077 board, Lamp guide
q; LB-077 board
9 Lamp guide
5 Three clawsPrism sheet
Illuminator
3Two claws
8 Two claws
1 Raise the EVF in the direction of the arrow A and slide it in the direction of the arrow B.
When separating the 7 LB-077 board and Lamp guide from the 6 VF lens assembly by removing the three 5 claws, do not face the side of the VF lens assembly on which the LB-077 board is installed, downwards. Because the Illuminator and others may fall out of the VF lens assembly, hold the illuminator and others using tape or paper as shown to prevent them from falling. Be careful on this point especially when removing the LB-077 board and Lamp guide because the three claws located in the VF lens assembly are easy to break.
Hold the illuminator and others using tape or paper as shown to prevent them from falling.
Caution
2-5
DCR-TRV16/TRV16E/TRV18/TRV18E/TRV116E/TRV118E
VF lens assembly
LB-077 board
[LB-077 BOARD SERVICE POSITION]
Adjustment remotecommander (RM-95)
AC poweradaptor AC IN
CPC-8 jig(J-6082-388-A)
2-3. FRONT PANEL SECTION
4 Screw (M1.7 × 4), lock ace, p2
1 Screw (M1.7 × 4), lock ace, p2
3 Open the jack cover assembly
7 Front panel sectionCaution
2 Screw (M1.7 × 4), lock ace, p2
6 FP-437 flexible board (24P)
5 Remove the Front panel section in the direction of the arrow A.
A
Because the 7 Front panel section is connected to the main unit by the 6 FP-437 flexible board, the flexible board may be damaged if you remove the Front panel section forcibly. Be very careful not to damage the flexible board.
Caution
2-6
DCR-TRV16/TRV16E/TRV18/TRV18E/TRV116E/TRV118E
2-4. MA-409, FB-219 BOARDS
1 Microphone (4P)
8 MA-409 board
MA-409 board
MA-409 board
Route the harness of the Microphone underneath the MA-409 board as shown in the illustration below.
FB-219 board
4 FB-219 board
2 Screw (M1.7 × 2.5), p
[MA-409 BOARD SERVICE POSITION]
Adjustment remotecommander (RM-95)
AC poweradaptor AC IN
FP-437 flexible board(24P)
5 Tapping screw (M1.7 × 3.5)
3 Tapping screw (M1.7 × 3.5)
7 Focus button FP-444 flexible board
Focus button
6 Focus button retainer
Caution
2-7
DCR-TRV16/TRV16E/TRV18/TRV18E/TRV116E/TRV118E
2-5. TOP CABINET ASSEMBLY
3 Screw (M1.7 × 4), lock ace, p2
2 Screw (M1.7 × 4), lock ace, p2
4 Claw
5 Top cabinet assembly
1 Slide the EVF in the direction of the arrow.
2-6. CABINET (R) SECTION
5 Remove the Cabinet (R) section in the direction of the arrow.
Because the 7 Cabinet (R) section is connected to the main unit using the 6 FP-434 flexible board, the flexible board may be damaged if you remove the Cabinet (R) section forcibly. Be very careful not to damage the flexible board.
7 Cabinet (R) section
4 Screw (M1.7 × 4), lock ace, p2
1 Screw (M1.7 × 4), lock ace, p2
2 Screw (M1.7 × 4), lock ace, p2
3 Open the cassette lid
6 FP-434 flexible board (40P)
Caution
2-8
DCR-TRV16/TRV16E/TRV18/TRV18E/TRV116E/TRV118E
2-7. BATTERY PANEL SECTION
A
VA-117
1 Screw (M1.7 × 4), lock ace, p2
1 Screw (M1.7 × 4), lock ace, p2
2 Strap bracket (lower)
4 Battery terminal board
3 BT panel assembly
3 Two screws (M1.7 × 4), lock ace, p2
6 Battery terminal board (6P)
5 Remove the BT panel section in the direction of the arrow A.
7 BT panel section
2 CPC lid
4 Open the cassette lid
2-8. EVF SECTION
VA-117
VA-117
6 EVF section
5 FP-435 flexible board (20P)
3 Screw (M1.7 × 2.5), p
4 Peel off the tape.
1 Slide the EVF slightly in the direction of the arrow so that the two screws 2 become visible.
2 Two tapping screws (M1.7 × 5)
2-9
DCR-TRV16/TRV16E/TRV18/TRV18E/TRV116E/TRV118E
2-9. LB-077 BOARD
8
1 Screw (M1.7 × 2.5), p
5 Two tapping screws (M1.7 × 6)
7 VF cabinet (upper) assembly
qa VF lens assembly
0 LB-077 board, Lamp guideqf LB-077 board
qd Lamp guide
9 Three claws
Prism sheet
Illuminator
6Two claws
2 Claw
4 VF flexible retainer sheet
3 Flexible retainer sheet metal
qs Two claws
When separating the 0 LB-077 board and Lamp guide from the qa VF lens assembly by removing the three 9 claws, do not face the side of the VF lens assembly on which the LB-077 board is installed, downwards. Because the Illuminator and others may fall out of the VF lens assembly, hold the illuminator and others using tape or paper as shown to prevent them from falling. Be careful on this point especially when removing the LB-077 board and Lamp guide because the three claws located in the VF lens assembly are easy to break.
Hold the illuminator and others using tape or paper as shown to prevent them from falling.
Caution
2-10
DCR-TRV16/TRV16E/TRV18/TRV18E/TRV116E/TRV118E
2-10.VA-117 BOARD (1)
VA-117
VC-280
5 VA-117 board
1 FP-436 flexible board (20P)
2 FP-434 flexible board
(12P)
(28P)
4 Board to board connector (100P)
3 Four screws (M1.7 × 2.5), p
VC-280
VA-117
VA-117 board
LB-077 board
[VA-117 BOARD SERVICE POSITION]
Adjustment remotecommander (RM-95)
FP-435 flexible board(20P)
AC poweradaptor AC IN
CPC-8 jig(J-6082-388-A)
Extension cord (100P)(J-6082-352-A)
Battery terminal board(6P)
VF lens assembly
To check the EVF circuit (IC4201 and IC4202), connect the LB-077 board to the VF lens assembly, and then set the camera to the "Forced EVF ON" mode.
Setting the “Forced EVF Power ON” mode
1) Select page: 0, address: 10, and set data: 00.2) Select page: 3, address: C4, and set data: 67.3) Select page: 3, address: C5, and set data: 01.
Exiting the “Forced EVF Power ON” mode
1) Select page: 0, address: 10, and set data: 00.2) Select page: 3, address: C4, and set data: 00.3) Select page: 3, address: C5, and set data: 00.
2-11
DCR-TRV16/TRV16E/TRV18/TRV18E/TRV116E/TRV118E
2-11.MAIN CHASSIS COMPLETE SECTION
VA-117
VA-117
2 FP-443 flexible board (6P)
3 Two screws (M1.7 × 2.5), p
4 Main chassis complete section
1 Control switch block (PS-CX2670)(20P)
2-12
DCR-TRV16/TRV16E/TRV18/TRV18E/TRV116E/TRV118E
2-12.VA-117 BOARD (2)
VA-117
VC-280
5 VA-117 board
1 FP-436 flexible board (20P)
2 FP-434 flexible board
(12P)
(28P)
4 Board to board connector (100P)
3 Four screws (M1.7 × 2.5), p
2-13.VC-280 BOARD
VC-280
1 Flexible board (from Lens block assembly) (27P)
2 FP-439 flexible board (16P)
4 FP-445 flexible board (30P)
3 Two screws (M1.7 × 2.5), p
5 VC-280 board
2-13
DCR-TRV16/TRV16E/TRV18/TRV18E/TRV116E/TRV118E
2-14.LENS SECTION
VC-280
1 Two screws (M1.7 × 2.5), p
2 Lens section
2-15.MECHANISM DECK
1 Four screws (M1.4 × 1.5)
2 Mechanism deck
2-14
DCR-TRV16/TRV16E/TRV18/TRV18E/TRV116E/TRV118E
2-16.JK-217, JK-218 BOARDS
2 JK-218 board
4 JK-217 board
1 Two screws (M1.7 × 2.5), p
3 Two screws (M1.7 × 2.5), p
2-17.CD-365 BOARD, 650A (CZ) BLOCK ASSEMBLY (LENS DEVICE)
3
1 Two tapping screws (M1.7 × 3.5)
2 Two tapping screws (M1.7 × 5)
2 Lens frame, External connector (Hot shoe)
1 FP-439 flexible board (16P)
3 Optical filter block
4 Seal rubber (W)
5 Remove the solderings
8 650A (CZ) block assembly (Lens device)
6 CCD block assembly
7 CD-366 board
2-15
DCR-TRV16/TRV16E/TRV18/TRV18E/TRV116E/TRV118E
VA-117
VC-280
[SERVICE POSITION TO CHECK THE VTR SECTION]Connection to Check the VTR SectionTo check the VTR section, set the VTR to the “Forced VTR power ON” mode.Operate the VTR functions using the adjustment remote commander (with the HOLD switch set in the OFF position).
Setting the “Forced VTR Power ON” mode
1) Select page: 0, address: 01, and set data: 01.2) Select page: 0, address: 10, and set data: 00.3) Select page: D, address: 10, set data: 02, and
press the PAUSE button of the adjustment remotecommander.
Exiting the “Forced VTR Power ON” mode
1) Select page: 0, address: 01, and set data: 01.2) Select page: 0, address: 10, and set data: 00.3) Select page: D, address: 10, set data: 00, and press the PAUSE button of the adjustment remote commander.4) Select page: 0, address: 01, and set data: 00.
To eject the cassette, connect Pin wd of the CN1501 on the VC-281 board to Pin w;(GND) of the CN1501 on the VC-281 boardfor a second.Note: Be sure to enter the "Forced VTR power ON" mode when ejecting the cassette.
CN15012
24 23
1
CPC-8 jig(J-6082-388-A)
AC poweradaptor AC IN
Adjustment remotecommander (RM-95)
Battery terminalboard (6P)
Extension cable (100P)(J-6082-352-A)
VA-117 board
VC-280 board
JK-217 board
JK-218 board
Mechanism deck
2-16
DCR-TRV16/TRV16E/TRV18/TRV18E/TRV116E/TRV118E
VA-117
VC-280
JK-218 board
JK-217 board
VC-280 board
VA-117 board
Adjustment remotecommander (RM-95)
Flexible board(From the Lens block assembly)(27P)
Lens block assembly
AC poweradaptor AC IN
Battery terminal board(6P)
Mechanism deck
FP-439 flexible board(16P)
[SERVICE POSITION TO CHECK THE CAMERA SECTION]Connection to Check the Camera SectionTo check the CAMERA section, set the CAMERA to the “Forced camera power ON” mode.When you want to operate the ZOOM and FOCUS, use the controls on the remote commander (with HOLD switch off).
Setting the “Forced Camera Power ON” mode
1) Select page: 0, address: 01, and set data: 01.2) Select page: 0, address: 10, and set data: 00.3) Select page: D, address: 10, set data: 01, and
press the PAUSE button of the adjustment remotecommander.
Exiting the “Forced Camera Power ON” mode
1) Select page: 0, address: 01, and set data: 01.2) Select page: 0, address: 10, and set data: 00.3) Select page: D, address: 10, set data: 00, and press the PAUSE button of the adjustment remote commander.4) Select page: 0, address: 01, and set data: 00.
Extension cable (100P)(J-6082-352-A)
2-17
DCR-TRV16/TRV16E/TRV18/TRV18E/TRV116E/TRV118E
CK-108
2 Two tapping screws (M1.7 × 3.5)
5 Control switch block (SH-CX2670)(18P)
6 Control switch block (KP-CX2670)(8P)
4 Tripod (Large)
3 Bottom frame
1 Three screws (M1.7 × 4), lock ace, p2
2-18.CK-108 BOARD<STEP1>
<STEP2>
CK-108
4 Two tapping screws (M1.7 × 3.5)
7 Tapping screw (M1.7 × 3.5)
5 Speaker retainer assembly
6 Speaker (2.0cm)
3 Speaker (2P)
8 Harness (PV-138)(8P)
2 Harness (PV-138)(20P)
1 P harness retainer
P harness retainer
Attach the 1 P harness retainer so that the harness does not come out as shown.
9 CK-108 board
Caution
2-18
DCR-TRV16/TRV16E/TRV18/TRV18E/TRV116E/TRV118E
2-19.HINGE ASSEMBLY
2
1 Four screws (M1.7 × 4), lock ace, p2
1 Two claws
3 Hinge cover (rear)
2 Hinge cover (front)
7 Hinge assembly
5 FP-442 flexible board
4 Screw (M1.7 × 2.5), p
6 Harness (PV-138)(8, 20P)
(Remove the LCD unit referring to section 2-1 before starting disassembling.)
2-19
DCR-TRV16/TRV16E/TRV18/TRV18E/TRV116E/TRV118E
2-20.CONTROL SWITCH BLOCK (PS-CX2670)
4 Zoom cover
2 Grip cover
1 Two screws (M1.7 × 2.5), p
3 Two tapping screws (M1.7 × 5)
(TRV18/TRV18E/TRV118E)
<STEP1>
<STEP2>
5 CS frame assembly
2 Two tapping screws (M1.7 × 3.5)
4 Tapping screw (M1.7 × 3.5)
3 Tapping screw (M1.7 × 5)
1 Tapping screw (M1.7 × 5)
2-20
DCR-TRV16/TRV16E/TRV18/TRV18E/TRV116E/TRV118E
3 Control switch block (PS-CX2670)
1 Tapping screw (M1.7 × 3.5)
2 FP-438 flexible board (8P) (TRV18/TRV18E/TRV118E)
<STEP3>
2-21.MEMORY STICK CONNECTOR (TRV18/TRV18E/TRV118E)
Eject knob
Caution
When removing the 3 Grip lock assembly, be careful that it can be easily caught by the dowel and the protrusion of the Eject knob shown in the illustration. Because the Eject knob is caught by the Grip lock assembly, the Eject knob can be easily removed if it is separated from the Grip lock assembly.
Dowel
7 Memory stick connector
4 Eject knob
1 Three tapping screws (M1.7 × 5)
3 Grip lock assembly
5 Screw (M1.7 × 2.5), p
2 Two screws (M1.7 × 2.5), lock ace, p2
6 FP-438 flexible board (10P)
2-21
DCR-TRV16/TRV16E/TRV18/TRV18E/TRV116E/TRV118E
2-22.CIRCUIT BOARDS LOCATION
MA-409
CK-108
VA-117
VC-280
LB-077
CD-365
JK-217
JK-218
PD161
FB-219
CCD IMAGERSWITCH, CONNECTORMANUAL FOCUS SENSORSTEADY SHOT, A/V IN/OUTDIGITAL IN/OUTEVF, EVF BACK LIGHTMIC IN, HP JACK, REMOTE CONTROL RECEIVER, SWITCHRGB DRIVE, TIMING GENERATOR, LCD DRIVE, BACK LIGHTAUDIO/VIDEO SIGNAL PROCESSCAMERA PROCESS, MPEG/DIGITAL STILL PROCESS, VIDEO/AUDIO SIGNAL PROCESS,SERVO, CAMERA/MECHA/HI CONTROL
CD-365CK-108FB-219JK-217JK-218LB-077MA-409PD-161VA-117
VC-280
NAME FUNCTION
2-22E
DCR-TRV16/TRV16E/TRV18/TRV18E/TRV116E/TRV118E
2-23.FLEXIBLE BOARDS LOCATION
FP-434
FP-441
FP-442
FP-435
FP-445
FP-443
FP-438
FP-436
FP-439
FP-437
CONTROL SWITCH BLOCK(PS-CX2670)
FP-444
TRV18/TRV18E/TRV118E
The flexible boards contained in the mechanism deck and that in the lens device are not shown.
DCR-TRV16/TRV16E/TRV18/TRV18E/TRV116E/TRV118E
COVERCOVER
LinkLink
3. BLOCK DIAGRAMS
POWER BLOCK DIAGRAM (1/3)
POWER BLOCK DIAGRAM (3/3)
POWER BLOCK DIAGRAM (2/3)
OVERALL BLOCK DIAGRAM (4/4)
OVERALL BLOCK DIAGRAM (3/4)
OVERALL BLOCK DIAGRAM (2/4)
OVERALL BLOCK DIAGRAM (1/4) POWER BLOCK DIAGRAM (1/3)
POWER BLOCK DIAGRAM (3/3)
POWER BLOCK DIAGRAM (2/3)
OVERALL BLOCK DIAGRAM (4/4)
OVERALL BLOCK DIAGRAM (3/4)
OVERALL BLOCK DIAGRAM (2/4)
OVERALL BLOCK DIAGRAM (1/4)
DCR-TRV16/TRV16E/TRV18/TRV18E/TRV116E/TRV118E
COVERCOVER 3. BLOCK DIAGRAMS3. BLOCK DIAGRAMS
3-1. OVERALL BLOCK DIAGRAM (1/4)
3-1 3-2
SECTION 3BLOCK DIAGRAMS
( ) : Number in parenthesis ( ) indicates the division number of schematic diagram where the component is located.
X250120MHz
X210124.576MHz
55
IC1403
135
59
63
CH SO,SCK
139
PANEL G
CAM SO,SI,SCK
29
PANEL B
IC2302
16
TPA+,-TPB+,-
PANEL R
ZOOM MOTORDRIVE
HALL ADAUDIOA/D CONV.
138
106
75
79
DV IN/OUT
73
2
AD0-AD13
68
71
IRIS PWM
EN1,DIR1 A,B
FC RSTIM RST
EN0,DIR0 A,B
EN0,EN1DIR0 A,BDIR1 A,B
FC RSTZM RST
DV SIGNAL
20
37
•
159
IC1402
PROCESS
DRIVE +,-
9
105
41•
33
78•
79
161
135
175
Y
14
HALL +,-
CCD OUT
V1-V4RG,H1,H2
6
170
78
C
L BUS
179
71
2
DV INTERFACE
73
68
31
11
MC BUS
75
FC RST
ZM RST
IC2102
128
TRCK
77
CN1006
21
TIMINGGENERATOR
24
9
CN5353
CN001
FOCUS MOTORDRIVE
IC1202IC1203
94
42
1
45
47
CD-365 BOARD(1/2)
LCK
6
145
EXT STROBO
EXT STROBO
142
4
18
51
141
127
153
IC1204
IC1201
156
152
L
IRIS HALL AMP
133
IRIS DRIVE
132
R
Y
C
127
IC2101
99
134
61
59
62
97
79
VC-280 BOARD(1/5)
HALL AD
81
EVF G
IRIS PWM
2
83
SHUTTER
12
IC1101
LENS ASSY
M
IC2501
18
PITCH ADYAW/PITCH
8
H
IRIS(SHUTTER)
SENSOR
YAW AD
AMP
MANUAL
129
YAW SENSOR
PITCH SENSOR
17
5
SHUTTERDRIVE
SE5301
8
SE5302
|
M
8
(1/2)
HD,VD
DATA TO SFD
FOCUSMOTOR
FOCUS
EVF R
DATA FROM SFD
1-4 10-12
SENSOR
FB-219 BOARD
JK-217BOARD(1/3)
EVF B
SFD BCK
4
88
123
120
VSP SO,SI,SCK
20
FRRV,TRRV,TRRT
6
18
FRRV,TRRV,TRRT
PANEL R,G,B
HD,VD
EVF R,G,B
Y
C
DATA TO SFDDATA FROM SFDSFD BCK
CAMERA CONTROL
CN6001 CN5903
CN5902
CN4003
CN1007
CN4002
PH6001,PH6002
21
ATF ERR
ZOOMMOTOR
ZOOMRESET
SENSOR
PB CK
66
56
25
6
AD DT
Y0-Y7
C4-C7
Y0-Y7
A0-A23
D0-D15
HS TXD,RXD,SCK
M
CN1201
C0-C3
HD,VD,OEHD,VD,OE
VD SI, SO, SCK
CCDIMAGER
NIGHT SHOT
IRISMETER
17
23
205
201
MC BUS
211
210MF A,B
TOOVERALLBLOCK DIAGRAM(3/4)
TOOVERALLBLOCK DIAGRAM(2/4)
213
ZOOM VR AD
6
207
HS TXD,RXD,SCK
IC2301
CN5352
215
130
67
203
211USBI/F
199
3
CN1401CN5001
CN5001
CN1401
2 2
21
1
1
REC DT
3
41
REC CK
7
TOOVERALLBLOCK DIAGRAM(4/4)
(PAGE 3-7)
3
11
8
S/H,AGCA/D CONV.
IC5001
8 5 11 13
8 5 11 13
173
12
38
35
37
44
45
25
28
18
21
22
X140136MHz
4
5
9
12
13
16
177
25
74
196
48
VCK
SHUTTER
CAM SO,SI,SCK
A0-A11
Y0-Y7
C0-C7
D0-D15
VCK
HD,VD
XSHDXSHPPBLKCLPDM
|
191
182
|
2
11
CLPOB
HD,VD
CH SO,SCK
XNS SW
IC170316MbitSDRAM
19 32
63 64 66
2 12 39 49•
Y0-Y7
DSCK
Y0-Y7
C0-C3
C0-C7
HD,VD,OE
HD,VD,OE
HD,VD
COL0-3
ADAI2
ADAO2
SFD BCK
Y0-Y7
VSP SO,SI,SCK
C4-C7
•
(2/15)
(1/15)
(1/15)
(3/15) (6/15)
(7/15)
MA-409BOARD(1/3)
VA-117BOARD(1/4)
FC A,BFC XA,XB
ZM A,BZM XA,XB
56
54
IC1801EVR17
16
55
56
54
171
172
9 2 34 27 22 11•
IC1704
A16-A23 D0-D7
153
|
170
48
47
117
118
119
65
|
72
76
|
83
91
|
97
99
|
115
34
2
6
IC2001
VIDEOA/D CONV.
38
37
36
42
|
49
52
|
59
84
85
86
144
137
133
130
139
7
6
140
43
|
46
27
28
42
HD,VD,OE
HD,VD,OE
58
47
54
57
190
195
194
191
65 82 63
8
18
24
206
202
212
214
208
216
204
200
22
2 49
13 15
611
183
184
88
87
62
|
93
60
|
39
221
223
IC2905DIGITALSTILL
CONTROL
(4/15)
(5/15)(5/15)
(10/15)
(3/15)
(2/15)
(2/15)
(2/15)
(13/15)
(11/15)
(4/15)
(9/15)
(9/15)
187
184 4
|
215
213
|
IC3002
259
48161
45
36
38
29
16MbitSDRAM
IC3003
32
24
27
19
49
12
39
2
CN1006CN5305
5
4
15
14
XTALOSC
X290148MHz
IC2904
AFCK(IC2001)
DSCK(IC1704)
XTAL 48M LK
XTAL 48M LK(IC2904)
USB D+,D-
USB D+,D-
SPCK(IC1704)
ASDATA
MCLK
238•
239
JK-218BOARD(1/3)
JK-218BOARD(2/3)
CONTROLSWITCHBLOCK(1/2)(PS-CX2670)
4
5
2
1
4
5
2
1
9
11
13
2
4
6
MS BS,DIO,SCLK MEMORYSTICK
CN5351CN5353CN1006
CN1008
8
9
7
8USB D+,D-
4 6
92 94
92 94
4 6
4
6
207
|
199
MPEGMOVIE
PROCESS
CHARACTERGENERATOR
AUDIO
DIGITALSTILL
PROCESS
AFCK
SPCK(IC1704)
47 48
AFCK(IC2001)
SPCK
Y
C
MF A,B
1
16
15
2
23 19
44
195
196
194
CAMERAPROCESS
CAMERA
LINE IN
19
5
7
17
FOCUSRESET
SENSOR
21
2 4
23
17
5 7
19
(1/2)
30
13
15
FLASHMEMORY
1
(PAGE 3-5)
2
(PAGE 3-3)
3
(PAGE 3-5)
4
DV OUT
TOOVERALLBLOCK DIAGRAM(3/4)
(USB)
(DCR-TRV18/TRV18E/TRV118E)
(TRV18/TRV18E/TRV118E)
(TRV16/TRV16E:E, HK, AUS, CH/TRV18/TRV18E:E, HK, AUS, CH, JE/TRV116E/TRV118E)
(TRV18/TRV18E/TRV118E)
Note
Note: DV IN/OUT
DV OUT
(TRV16/TRV16E:E, HK, AUS, CH/TRV18/TRV18E;E, HK, JE,AUS, CH/TRV116E/TRV118E)
(TRV16E:AEP, UK, EE, NE/TRV18E:AEP, UK, EE, NE)• Abbreviation
EE : East European modelNE : North European modelHK : Hong Kong model
AUS : Australian modelCH : Chinese modelJE : Tourist model
DCR-TRV16/TRV16E/TRV18/TRV18E/TRV116E/TRV118E
COVERCOVER 3. BLOCK DIAGRAMS3. BLOCK DIAGRAMS
3-3 3-4
3-2. OVERALL BLOCK DIAGRAM (2/4) ( ) : Number in parenthesis ( ) indicates the division number of schematic diagram where the component is located.
PD-161 BOARD(1/3)
VC-280 BOARD(2/5) CK-108BOARD
(1/3)
RGBDRIVE
VCOM
VR,VG,VB
COM
DAC VGLAC
2.5 INCHLCD UNIT
LCD901
CN5501
CN5203CN5202CN1005 CN5652
PANEL 2.8V
Q5601
(1/2)
(1/2)
IC5501484746
27
CURRENT
INVERTER
BACKLIGHT
T5601Q5604/Q5605ND901
BACKLIGHT
D5602(STARTER)
BL HIGH
BL LOW
DETIN
CN5601
DRIVE
DET
IC56023 4
35
202224
4039
TIMINGGENERATOR
SP901SPEAKER
HD OUT
(2/2)
(2/2)
IC5502
IC5601
1
1
484
5 2
6
7
464542
2 58
12
24
11
192021
45
1012
18
BL REG10
3
CN5651CN5201
CN5205
CN6101
SP+,-
21
Q5603
LED DRIVE
10
1532
98
1413
12 4
4
10
1532
98
13
4
12 4
21
13
222119
1517
2324
2527
VGPANEL COM
XHD OUT
PANEL R,G B
HDVD
14
7
21
VD,SO,SCK
BL CONT
SP+,–
28
192022
2624
17
1614
18
20
18
2422
1416
20
18
2422
1416
3
1
7111054
PANEL VGCN1002FORADJUSTMENTS
PANEL R,G,B
DATA TO SFD
VD SO, SCK
VSP SO, SCK
DATA FROM SFDSFD BCK
HD,VD
PANEL COM
TOOVER ALLBLOCK DIAGRAM (4/4)(VA-117)
TOOVER ALLBLOCK DIAGRAM (1/4)
TOOVER ALLBLOCK DIAGRAM (3/4)
XHDEVF VCOEVF VG
IC4202TIMING
GENERATOR
COLORLCDUNIT
14
1315
1612
3
LB-077 BOARDVA-117 BOARD(2/4)
MA-409 BOARD
(2/3)
10711
9
18
8
4 BACK LIGHT DRIVE
D6102BACKLIGHT
R,G,B
BCK, HCK1/2, HST, EN, STB, VCK, VST
COM
Q6102
IC6101
CN6102
LCD903
17
CN4201
CN1007 CN4002
1114
1312
3
10
IC4201RGB
DRIVE
EVF R,G,B
VD SO,SCK
HD
VCO
G
VD
(1/6)
(1/6)
(2/6)
(6 /6)
(11/15)
202224
464542
484746
14
1 8
148
4039
97
24 8
14
YC
GG
27
26
3028
6264
467
3634
5658
3532
19
181422
394842
18
1715
S VIDEO (OUT)
S VIDEO (IN/OUT)
AUDIO/VIDEO (OUT)
AUDIO/VIDEO (IN/OUT)
YCV
L
16C
ACC
J5302(1/2)
AGC
VIDEO IN/OUT
V
JK-217 BOARD(2/3)
VC-280 BOARD(3/5)
R
R
R
19
LR
LR
12
V
L
L
10
J5302(2/2)
R
63
51
49
6460
L
RL
8
6414
49
60
51
R
CN5305
SHOE MIC L FP-436 (FLEXIBLE)
CN4003
CN5902CN5901
CN1006
INTELLIGENTACCESSORYSHOE (1/2)
CN1007
VSP SO,SCK
CN4004
CN4002
CN4001
L
Y
IC4301AUDIO
I/O
IC4101
YC
YC 26
24
22
20
18
9 10
2 3
757377
6870
74
76
71
72
54
53
45
43
59
56
58
57
50
46
48
44
757377
6870
74
76
71
72
54
53
45
43
59
56
58
57
50
46
48
44
DATA FROM SFDIC2201
D/A CONV.A/D CONV.
RL
R
R
L
L
RL
DATA TO SFDSFD BCK
HP RHP L
HP RHP L
1516
32
98
12
(3/6)
MIC AMP
IC4401
1
333
35
2214
EVF R,G,B
Y
L
R
Y
O
C
3648
MIC901 MIC L
MIC R
J5901MIC
(PLUG IN POWER)
J5902
(HEADPHONES)
15 3
3
(PAGE 3-2)
5
(PAGE 3-5)
6
(PAGE 3-7)
Note
Note
S VIDEO (OUT) AUDIO/VIDEO (OUT)
S VIDEO (IN/OUT) AUDIO/VIDEO (IN/OUT)
Note
(TRV16E:AEP, UK, EE, NE/TRV18E:AEP, UK, NE,EE)
(TRV16/TRV16E:E, HK, AUS, CH/TRV18/TRV18E:E, HK, AUS, JE, CH/TRV116E/TRV118E)
• AbbreviationEE : East European modelNE : North European modelHK : Hong Kong model
AUS : Australian modelCH : Chinese modelJE : Tourist model
DCR-TRV16/TRV16E/TRV18/TRV18E/TRV116E/TRV118E
COVERCOVER 3. BLOCK DIAGRAMS3. BLOCK DIAGRAMS
3-3. OVERALL BLOCK DIAGRAM (3/4)
3-5 3-6
( ) : Number in parenthesis ( ) indicates the division number of schematic diagram where the component is located.
SWP
X250120MHz
16
MODE SW A - MODE SW C
CONTROL
SREEL FG
CAP ON,CAP FWD
DRUM PWM
FRRVTRRTTRRV
TAPE LED ON
13
CAP PWM
|
LOAD,UNLOAD
DRUM PG
15
DEW AD66
63
65
36
38
1
80
77
75
67
64
33
32
72
69
63
68
65
74
78
76
82
80
83
69
67
70
84
179
178
52
32
33
45
CAP FG
TAPE END
TAPE TOP
106
DRUM FG
TREEL FG
MECHA
108
|
EEPROM
2-4
VSP SO,SI,SCK
VD SO, SCK
VD SO, SI, SCK
VSP SO,SI,SCKVSP SO,SCK
FRRV TRRT,TRRV
MC BUS
HI SO,SI,SCK
REC PROOF
CHIME SDA,CHIME SCK,CHIME VDD
XCC DOWN
(2/2)
LPF
CAP ERROR
DRUM ERROR
11
15
IC4501(1/2)
PWM
64
58
SWITCHING
SWITCHING
Q4509
Q4510
20
SENSOR
MOTOR
J MECHA DECK
DRUM FG AMP
S902
1
|
LOADINGDRIVE MOTOR
H001
H002
C INS903
CN1010
D901
5
11
CONNECTOR
TAPE TOP SENSOR
Q902
DRUM FG
CAPSTAN
MODE
24
SENSOR
15
S REEL
SWITCH
XCC DOWN
S REEL +, –
T REEL +, –
LM +, –
18
MOTOR
CN1009
21
TAPE END DETECT
4PIN
T REEL
|
TAPE TOP DETECT
7
LOADING MOTOR
TAPE LED
M
REEL FG AMP
M903
REC PROOF
9
16
SENSOR
DRUM
TAPE END SENSOR
|
20
10
5
CAPSTAN
DRUM PG
23
|
2
M
12
DRUM PG AMP
27
CAP VS
DEW
17
4
25
DRUM VS
FG
M902
1
DRUM
S901
Q901
CN901
|
M901
25
22
TOOVERALLBLOCK DIAGRAM(4/4)
TOOVERALLBLOCK DIAGRAM(2/4)
17 20
SWP
CN1002FOR ADJUSTMENTS
AD DT
6
PB Y OUT
1
EQ
20
PB CK
6
REC/PB 7
2
15
6
CN1901
EVEN 3
ODD
2
5
22 24
VSP SO, SCK
REC CK
REC DT
PB CKTOOVERALLBLOCK DIAGRAM(1/4)
(PAGE 3-2)
VC-280 BOARD(4/5)
166
165FG AMP
(13/15)
(13/15)
(12/15)
(12/15)
(8/15)
(8/15)
(4/6)
111
164
190
89
88
197
198
192
193
196
195
119
180
1
3
ATF ERR
13
34 31
4
53 52
4950
29
25
21
19
20
18
35
42
IC1901
IC190240
42
27
REC CK
REC DT
RF MON
AD DT
6
IC2401
MOTORDRIVE
MOTORDRIVE
CAPSTAN
DRIVE
IC2401(RABI)
LPF
4
|
1
11
14
|
M
CN1011
IC2502
IC2501
A/D CONV.PLL
AMP
CAPSTAN
DRUM
41
44
43 20
18
20
1845
19,21
15,17
19,21
15,17
CN4002 CN4002 CN1007CN1007
26 27
7 8
22 23DEW AD
DRUM U,V,W
CAP U,V,W
FG 1,2
SPCK (IC1704)
(1/2)
(2/2)
VA-117 BOARD (3/4)
2
(PAGE 3-3)
5
TOOVERALLBLOCK DIAGRAM(1/4)
(PAGE 3-1)
4
(PAGE 3-8)
7
DCR-TRV16/TRV16E/TRV18/TRV18E/TRV116E/TRV118E
COVERCOVER 3. BLOCK DIAGRAMS3. BLOCK DIAGRAMS
3-4. OVERALL BLOCK DIAGRAM (4/4)
3-7 3-8
( ) : Number in parenthesis ( ) indicates the division number of schematic diagram where the component is located.
S
BT901
Q4602
10MHzX3101
32.768KHzX3102
S5203
BT5201
Q4610
2
5
1
BATTERYTERMINAL
DC IN 3
2
4
IC4501
IC4505DC/DC
CONVERTER
D 1.9V
PLL1.5V
D 1.5V
1.5V(IC1601)
PANEL -15.3V
A 2.8V
AU 2.8V
MT 5V
CAM -6.5V
CAM 12V
IC2703
IC2905
LANC I/O
1110
12
I/F43
42
74
VDD SWITCH
IC27027
4
3
5
6
RESET
79
3
59
41
45
14
53
62
73
66
XPHOTO STBY SW
XS/S SW
XCAM MODE SW
DIAL A
VCC
XRESET
IB SI
IB SO
BATT/EXT
IC3101HI CONTROL
HI CONTROL
67
29
28
51
52
5
35
37
SIRCS PWM
XCC DOWN
XCC DOWN
37
168
30
REC PROOFREC PROOF
CHIME SDA
CHIME SCK
CHIME AD0
CHIME SDACHIME SCKCHIME VDD
CHIME AD
XEJECT SW
XEJECT SW
RXD
KEY AD5
KEY AD0
KEY AD5
SIRCS SIG
VTR DD ON
SHOE ON
CONTROL SWITCHBLOCK(KP-CX2670)
SEL/PUSHEXEC
S103,S102 EXEC
CN3203
CN5202 CN1005
CN1008
CN5203
CN5652
CN5653
CN5903
CN5207
CN5201
1
15
CK-108BOARD(2/3)
PD-161BOARD(2/3)
MA-409BOARD(3/3)
VA-117BOARD(4/4)
(2/2)
(2/2)
MEMORY FUNCTION SW,MENU SW,VOLUME SW,DISPLAY SW,REC SW
VTR FUNCTION SW
S5201-5206
S101-116
CN4003 CN4002 CN1007
Q4001,4003
CN5902
CN4001
RESET
S100,101
BACK LIGHT SWEXPOSURE SW
LITHIUMBATTERY
CONTROL SWITCHBLOCK(PS-CX2670)
POWER SW
START/STOP SW
S1
S2
68 KEY AD6
PANEL REVERSE SW
S501
PHOTO SW
S71PHOTO REC
KEY AD0
IR ON
ZOOM VR
LED DRIVE
RV001
CN4601
D 2.8V
EP 2.8V
EP 13.3V
RP 4.75V
A 4.75V
AU 4.75V
VC-280 BOARD(5/5)
606165 KEY AD3
KEY AD4
KEY AD1
KEY AD2 A
80 DIAL B
57 SHOE ID1
SHOE ON
58 SHOE ID2
XVTR MODE SW
2
1
7
KEY ADD
6 XPHOTO FREEZE SW
20
4
21
25
24
23TXD
TXD,RDX,SCK
SCK
RXD
185
191
190 TXD
CAM DD ON
IR ON
SCK
39
40
LANC IN
LANC OUT
17
FAST CHARGE
VTR UNREG
CN1007CN4002
CN4004
Q3101
BATT LI 3V
CK-108BOARD(3/3)CN5202
10
9
31
32
17
18
17
18
28
10
20
1
LCDDRIVE
IC5651
7
811
30
CN5654
CN5203CN1005 CN5652
PD-161 BOARD (3/3)
12
1
2
12
1
2
CD-365BOARD(2/2)
SUPER NS/COLOR SLOWS
(LANC)
S5351
J5301
LANC SIG
LANC SIG
ZOOM VR AD
EXT STROBO
HS TXD,RXD,SCK
HI EVER SO
HI EVER SCK
XOSD SCK
16
BATT SIG
BATT SIG
BATT/EXT
FAST CHARGE
BATT UNREG
VTR UNREG
VTR DD ON
CAM DD ON
BL REG
BL CONT BL CONT
CONTROLSWITCHBLOCK(SH-CX2670)
(4/6)
(14/15)
(14/15)
(14/15)
(4/15)(4/15)
(2/2)
1
3
4
65
65
PRT HEAD UNREG
SHOE UNREG
LANC SIG
EXT STROBO
SHOE ID1,2
HS TXD,RXD,SCK
14
15
11
9
12
10
7
8
13
4
12
7
9
6
8
11
10
5
93
90
91
89
79
80
82
86
85
84
87
93
90
91
89
79
80
82
86
85
84
87
INTELLIGENTACCESSORYSHOE
FP-309(FLEXIBLE)
FADERFOCUS/INFINITY
S301,302
FP-444(FLEXIBLE)
JK-218 BOARD (3/3)
JK-217 BOARD (3/3)
EJECT SW
CN5353
CN5305
CN1006
CN1401
CN5001 CN5002 S201
EDIT SERCH+/-
S202,203
FP-443(FLEXIBLE)
TOOVERBLOCK DIAGRAM(3/4)
END SEARCH SW,AUDIO DUB SW,INDEX SW
3635
38
37
39
40
34
33
56
3
4
2
1
7
8
42
16
18
19
5
1
1
3
4
6
9
1
8
7
5
DIAL A,B
. .
.
.
.
160
.
162
.
221
HI SO
HI SO,SI,SCK
HI EVER SO,SCK
HI SI
XHI SCK
200
201.
.
199
EEP TXD
EEP RXD
EEP SCK
207
206
205
222223
.
.
.
3
D5901,5902
IC5901REMOTE
COMMANDER
(NS LED)
RECEIVER
.
.
.
.
.
.
5
1
2
3
8
6
25
23
5
1
2
3
8
6
25
23
(2/2)
TOOVERALLBLOCK DIAGRAM(2/4)
(PAGE 3-3)
TOOVERALLBLOCK DIAGRAM(1/4)
EEPROM
IC2901.
. 8,11
2
9,12
4
14
4
14
6
1
11
18
COM1-4SEG1-16 LCD
INDICATOR
LCD902
6
(PAGE 3-1)
1
(PAGE 3-5)
7
DCR-TRV16/TRV16E/TRV18/TRV18E/TRV116E/TRV118E
COVERCOVER 3. BLOCK DIAGRAMS3. BLOCK DIAGRAMS
3-9 3-10
3-5. POWER BLOCK DIAGRAM (1/3) ( ) : Number in parenthesis ( ) indicates the division number of schematic diagram where the component is located.
L4503
L4506
L4502 L4513
L4515
L4514
L4501
L4508
L4507
L4510
L4504
L4505
F4602
F4603
F4604
F4601
F4605
L4509
L4516
Q4508
Q4505
Q4506
Q4510
Q4503
Q4509
L4511
L4522
L4520
BATT/XEXT
F4606
L4519
30
28 2VCC
40
42
50
45
6
29
IC4501DC/DC CONVERTER
27
49
1
5
21
22
4
1
5
6
2
3
34
37
46
11
64
58
15
OUTPUTVCC-1,2,3
OUTPUTVCC-4,5,6
OUTPUTVCC-7
VREF
RT
CT
STANDBY-3
STANDBY
NONINV INPUT-5
NONINV INPUT-6
OUTPUT-1
MOS GATE-1
OUTPUT-7
OUTPUT-3
OUTPUT-2
OUTPUT-6
OUTPUT-5
OUTPUTMONITOR-1
OUTPUTMONITOR-7
7MONITORINPUT-7
31STANDBY-7
OUTPUTMONITOR-3
OUTPUTMONITOR-2
SWITCHING
SWITCHINGQ4512
Q4511SWITCHING
SWITCHINGQ4501 T4501
D 1.5V
PLL 1.5V
BL REG
BL CONT
1.5V(IC1601)
A 2.8V
AU 2.8V
D 2.8V
A 4.75V
RP 4.75V
A 4.75V
AU 4.75V
CAP VS
DRUM VS
CAP ERROR
6
1
5
4
3
2
Q4601,4602
Q4605, Q4607, Q4609Q4606, Q4608, Q4610 (DCR-TR18/TRV18E/TRV118E)Q4611 (DCR-TR16/TRV16E/TRV116E)
SHOE ON
SHOE UNREG
PRT HEAD UNREG
CHARGESWITCH
BATT UNREG
ACV UNREG
Q4603, 4604
OUTPUTMONITOR-4
OUTPUT-4 57
MOS GATE-4
18
54
8
S BATT SIG
VTR DD ON
5V REG
EMERGENCYDETECT
Q4513
-6.5V REG
Q4517,4518
13.3V REG
Q4521
DC IN
IC4505
Q4502,4504,4507
VIDEOIN/OUT
VA-117 BOARD
LF4601
CN4601
BT901
BATTERYTERMINAL
DRUM ERROR
COMP 41
VREF
SWITCHING
SWITCHING
SWITCHING
SWITCHING
SWITCHING
BAT
T FE
T O
N
INIT
CH
AR
GE
ON
D4503RECT
A 4.75V
EP 2.8V
1.5V (IC1601)
A 2.8V
D 1.9V
RP 4.75V
BATT SIG
BATT UNREG
TOPOWERBLOCKDIAGRAM(2/3)(VC-281
EP 13.3V
CAM -6.5V
EP 4.75V
PANEL -15.3V
D 2.8V
1.9V REG
RECT -15.3V REG
D4502
EP 13.3V
INIT CHARGE ON
SHOE ON5
BATT/XEXT
VTR DD ON
CAM DD ON
FAST CHARGE
BATT UNREG
MT 5V
VTR UNREG
EP 13.3V
D 2.8V
PLL 1.5V
CAP VS
CAP ERROR
DRUM VS
DRUM ERROR
CAM 12V
COLORLCDUNIT
IC6101BACKLIGHTDRIVE
20
IC4201 IC4202TIMING
GENERATORRGB
DRIVE
IC5901REMOTE
COMMANDERRECEIVER
CN4201
LED ON/OFF
CN6101CN6102
LCD903
EP 13.3V
EP 2.8V
EP 4.75V
16
Q4519,4520
D 1.5V
D 1.9V
LB-077 BOARD
MA-409 BOARD
FB-219BOARD
12VREG
CAM DD ON
CAM 12V
Q4514-4516
CAM -6.5V
(PAGE 3-11)
7
81
1
4
1
20
17
8
FB4202
CN4004
BL REG
BL CONT
PANEL -15.3V
PANEL 13.3V
PANEL 4.75V
PANEL 2.8V
EP 13.3V
EP 4.75V
EP 2.8V
7
6
5
4
3
TOPOWERBLOCK DIAGRAM(3/3)(CK-108)(PAGE 3-13)
CN4001
3
1
4
215
14
FP-436(FLEXIBLE)
INTELLIGENTACCESSORY
SHOE
IC4301AUDIOIN/OUT
IC4401MICAMP
IC4101
34
35
18
20
15
17
19
21
31
33
8
9
7
9
27
29
11
13
14
16
26
28
30
32
10
12
36
6
8
2
3
23
25
4
1A 4.75V
D 2.8V
MT 5V
MT 5V
CN4002
AU 2.8V
AU 4.75V
REG
Q4301
SP VCC
C/D VS 1.5V
BL REG UNREG
VTR UNREG
NIGHTSHOTLED
CN5902 CN4003CN5903
CN6001
D6001
D5901, 5902
PH6001, 6002
11
5
9
11
5
9
TALLYLED
MANUALFOCUS
SENSOR
6
2
5
1
MT 5V
R4011,4012
A 4.75V
AU 4.8V
1
2
(DCR-TRV18/TRV18E/TRV118E)
DCR-TRV16/TRV16E/TRV18/TRV18E/TRV116E/TRV118E
COVERCOVER 3. BLOCK DIAGRAMS3. BLOCK DIAGRAMS
3-11 3-12
3-6. POWER BLOCK DIAGRAM (2/3) ( ) : Number in parenthesis ( ) indicates the division number of schematic diagram where the component is located.
D2071
S5203
BT5201
FB2502
FB1702
FB2101FB2903
FB3001
L1902
FB1901
FB1201
Q2706
Q2401
R2431
2
IB SI
BATTER INDETECT
1
XLANC PWR ON
RESET
43
BATT INREG
VCC
Q2701
8
XRESET
17
BTT LI 3V
BATT/XEXT
ACV SENSI/F
FAST CHARGE
Q3101
VTR UNREG
DV
IC2702
VTR DD ON
D 2.8V
LANC I/O
INIT CHARGE ON
VIDEO
VTR DD SENS
31
HI CONTROL
A/D CONV.
56
XREEL
FC RST LED
ZM RST LED
HALL ON
IC3101
73
153
IC2703
37
AUDIOAUDIO
55
A/D CONV.
VCC
A 2.8V
L2201
74
BATT SIG
CAM DD ON
54
LANC DC
42
POWER
ADC&DAC
8
UNREG
XPHOTO STBY SW
BATT SENS
4
38
XCAM MODE SW
14
7
SHOE ON
XVTR MODE SW
1
DV
IB SO
MT 5V
RP 4.75V
A 4.75V
CN1007
PLL 1.5V
D 1.9V
D 2.8V
A 2.8V
1.5V (IC1601)
IC1002 IC2301
IC1402D 1.5V
D 2.8V
USB 3.1V
TOPOWER BLOCKDIAGRAM(1/3)(VA-117)
VC-280 BOARD
RESET
LITHIUM BATTERY
EVER 3.0VTOPOWERBLOCK DIAGRAM(3/3)(PD-161)
T REEL,
13
19
4PIN18
J MECHA DECK
SENSOR VCC
CHIME VDD
FOCUS
SENSOR
ZOOM
SENSOR
SHOE ON
BATT SIG
INIT CHARGE ON
VTR DD ON
CAM DD ON
FAST CHARGE
BATT/XEXT
BATT UNREG
MT 5V
VTR UNREG
1.5V(IC1601)
D 1.9V
A 2.8V
D 2.8V
D 1.5V
PLL 1.5V
A 4.75V
RP 4.75V
CAP VS
CAP ERROR
DRUM VS
DRUM ERROR
CAM 12V
CAM -6.5V
3
7
5
4
8
6
IC1902 IC1901
S/H,AGCA/D CONV.
IC1403
IC2001 IC2101 IC2102
IC2201 IC2302
LANC DC
20
6
10
14
CN001
CN1008
Q1001,1002
CAMERA
IC2501CONTROL
INTERFACESIGNALPROCESS
D 2.8V
EEPROM
IC2502
28
40
39
13
1
2
CN1005
CN5202
D1.5V
PLL 1.5V
D2.8V
CN5203
30
CN1006 CN5305
12
20
2
USBI/F
3.1VREG
IC1704
TIMINGGENERATOR
REC/PBAMP
EQ,A/D CONV.
PLL
A 2.8V
D 1.9V
MT 5V
IC170316MSDRAM
RP 4.75V
A 7.45V
EP 13.3VEP 13.3V
RV001
ZOOM VR
LED
D 2.8V
MS VCCUSB 3.1V
MS VCC ON
D2.8V
EVER 3.0V
LANC DC
SE 2.8VSE 2.8V
CK-108 BOARD(1/2)
JK-217 BOARDSENSORPITCH,YAW
SENSOR AMPPITCH/YAW
SE5301, 5302
LANC
J5301
CONNECTOR
S REELSENSOR
TAPE LED
DRUM FG,PG AMPMOTOR DRIVE
IC2401
43REEL FG AMP
LOADING
DRUM,CAP ERROR AMPTAPE TOP,END DET
DRUMCAPSTAN FG AMP
CAPSTAN MOTOR DRIVE
MOTOR DRIVE
DRUM ERROR
CAP VS
EV 13.3V
CAP ERROR
DRUM VS
CN1010
TAPE LED A
D 2.8V
MT 5V
A 2.8V
D 2.8V
CAM DD ON
VTR UNREG
CH
IME
PW
R C
ON
T
XR
EEL
HA
LL O
N
LENS ASSY
IC5001 CCD
IMAGER
FC RST LED
ZM RST LED
16
8
CN1201FC SENS VCC
ZM SENS VCC
CN5001
CN1401
Q1203(1/2)
Q1203(2/2)
CAM 12V
CAM -6.5V
DIGITAL
HICONTROL
CAM DD ON
MS VCC ON
CHIME PWR CONT
IC2905
CONTROL SWITCHBLOCK(PS-CX2690)
S1
5
2
4
VCR
PLAYER
OFF(CHG)
MEMORY
POWERCAMERA
IC1101
L1101
CD-365 BOARD
EEPROM
IC2901
OSCXTAL
IC2904BUFFER
IC2903
SDRAM
16M
IC3003
3
7MEMORY
STICK
16
35
STILLCONTROL31
23
168
57
55
IC1201SHUTTERDRIVE
IC1204FOCUS/ZOOM/MOTORDRIVE
IC1202IC1203DRIVEIRIS
HALL AMP
IC1801EVR
MEMORY
16M
FLASH
IC3002
145362
7577
6467
RESET
RESET
16
9
16
9
5
32
42
MPEG MOVIEDIGITAL STILLPROCESS
5
1
4
3
23
25
2
8
35
34
26
28
30
14
16
11
13
27
29
31
33
19
21
15
17
7
9
6
36
12
10
32
18
20
R1022
45
(PAGE 3-10)
2
(PAGE 3-13)
3
(TRV18/TRV18E/TRV118E)
(TRV16/TRV16E:E, HK, AUS, CH/TRV18/TRV18E:E, HK, AUS, CH/TRV116E/TRV118E)
(TRV18/TRV18E/TRV118E)
(TRV18/TRV18E/TRV118E) (TRV18/TRV18E/TRV118E)
(TRV16E:AEP, UK, EE, NE/TRV18E:AEP, UK, EE, NE)
(TRV16/TR16E:E, HK, AUS, CH/TRV18/TRV18E:E, HK, AUS, CH, JE/TRV116E/TRV118E)
(TRV18/TRV18E/TRV118E)
• AbbreviationEE : East European modelNE : North European modelHK : Hong Kong modelAUS : Australian modelCH : Chinese modelJE : Tourist model
DCR-TRV16/TRV16E/TRV18/TRV18E/TRV116E/TRV118E
COVERCOVER 3. BLOCK DIAGRAMS3. BLOCK DIAGRAMS
3-13 3-14E
3-7. POWER BLOCK DIAGRAM (3/3) ( ) : Number in parenthesis ( ) indicates the division number of schematic diagram where the component is located.
CN5651
CN5652
CN5501EP 4.75V
EP -15.3V7
4
3
5EP 13.3V
6EP 2.8V
8
7
4
3
5
6
8
PANEL 4.75V
BL CONT
PANEL -15.3V4
7
BL REG89
6PANEL 13.3V
5PANEL 2.8V
3
24
3
1
23
PD-161 BOARD
CK-108BOARD
(2/2)
TOPOWERBLOCK DIAGRAM(1/3)(VA-117)
TOPOWERBLOCK DIAGRAM(2/3)(CK-108)
FB5503CN5202 CN5204
FB5502
FB5501
IC5601,5602INVERTER
BACK LIGHTDRIVE
IC5501
RGBDRIVE
IC5651INDICATOR
LCDDRIVE
IC5502
TIMINGGENERATOR 28
LCDUNIT
LCD901
ND901BACKLIGHT
10
16
Q5502-5505
CN5601
BL HIGH
EVER 3.0V
(PAGE 3-9)
1
(PAGE 3-12)
3
DCR-TRV16/TRV16E/TRV18/TRV18E/TRV116E/TRV118E
COVERCOVER 4-2. SCHEMATIC DIAGRAMS 4-3. PRINTED WIRING BOARDS4-2. SCHEMATIC DIAGRAMS 4-3. PRINTED WIRING BOARDS
4-1 4-2
4-1. FRAME SCHEMATIC DIAGRAM (1/3)
FRAME SCHEMATIC DIAGRAM (1/3)
SECTION 4PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS
20PCN5305
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
10P
CN
1011
12345678910
27P
CN
1010
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27
10P
CN
1901
12345678910
20PCN1002
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
27P
CN
1009
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27
6PCN5002
1
2
3
4
5
6
16PCN5001
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
24PCN1201
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
16PCN1401
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
12PCN5353
1
2
3
4
5
6
7
8
9
10
11
12
30PCN1006
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
1
A
REG_GNDLM
_UN
LOA
D
TREE
L+
PS_V
HE_
GN
D
H_START
XM
OD
E_S
W_B
CA
P_V
XLANK_JACK_IN
XC
CD
OW
N_S
W
FP-4
39
GN
D
FG1
VIDEO_I/O
CA
P_W
HA
LL_G
ND
LANC_SIG(N.C.)
UH
E+
CA
P_U
YS_V
CD-365BOARD
XM
OD
E_S
W_A
REG_GND
CA
P_U
RF_MON
YS_LI
CA
P_V
YEV
EN
SE_2.8VC
HIM
E_S
DA
CA
P_U
LANC_SIG
CA
P_V
PANEL_VG
XO
DD
REG_GND
PS_LI
XR
EC_P
RO
OF
CA
P_U
JIG_TDO(N.C.)
MD(J MECHANISM)
FP-4
43
REG_GND
GND
CA
P_W
FG_V
CC
SWP
XS
DL
EDIT
- S
W
AU_LINE_I/O_R
GND
CA
P_W
FG_G
ND
XHD/PSIG
YS
DL
EDIT
+/
FG_G
ND
JIG_TDI(N.C.)
HE_
VC
C
GN
D
TMS(MAKER_CHECK)
UH
E-
EJEC
T/
DR
UM
_UFG2
GN
D
GND
CA
P_W
SW
YO
DD
PANEL_COM
Shot
DR
UM
_W
WH
E-
MIC
/REC
_SW
_GN
D
EVF_BL+(N.C.)
Night
TAP
E_LE
D_K
KEY_AD0
EVF_VG
FG
VH
E+
GND
SW
_CO
M/S
W_G
ND
RF_IN/LANC_JACK_IN
N.C
.
PG
GND
SR
EEL+
TCK(N.C.)
S_Y_I/O
Super
DR
UM
_W
GND
TAP
E_TO
P
SR
EEL-
EVF_BL-(N.C.)
LANC_DC
DV_JACK
GND
DR
UM
_V
LM_L
OA
D
EVF_VCO
CH
IME_
SC
K
USB_JACK
XEJECT_SW
M_C
OM
TOP
/EN
D_G
ND
S_C_I/O
TAP
E_LE
D_A
FP-4
45
DR
UM
_V
LM_L
OA
D
PD_VCO
HA
LL_V
CC
CPC
TAP
E_EN
D
AV_JACKX
MO
DE_
SW
_C
VH
E-
DR
UM
_U
REG_GND
S VIDEOTERMINAL
WH
E+
FG/P
G_C
OM
AU_LINE_I/O_L
CH
IME_
VD
D
LANC_JACK
CA
P_V
DEW
+
JK-217BOARD
XEV
EN
LM_U
NLO
AD
AV_JACK_IN
DEW
-
XS_JACK_IN
FG_V
CC
TREE
L-
GN
D
CCD_GND
12V
H1
CCD_OUT
V3
RG
CCD_GND
H2
XEJECT_SW
V2
V4
V1
KEY_AD0
V_DRAIN
VSHT
-6.5V
FC_SENS_OUT
NightShot_Vcc
FC_XB
FC_XA
Gnd
FC_B
Gnd
ZM_SENS_Vcc
Gnd
THERMO_OUT
ZM_XA
HALL(+)
ZM_XB
BIAS(-)
BIAS(+)
DRIVE(+)
FC_A
ZM_A
ZM_B
DRIVE(-)
HALL(-)
ZM_SENS_OUT
Gnd
FC_SENS_Vcc
V4
V_DRAIN
V3
-6.5V
KEY_AD0
VSHT
H2
12V
CCD_GND
H1
XEJECT_SW
RG
CCD_OUT
V2
CCD_GND
V1
TPB
USB_D-
REG_GND
USB_DET
REG_GND
REG_GND
KEY_AD5
TPA
REG_GND
NTPB
USB_D+
NTPA
JK-218BOARD
AU_LINE_I/O_L
USB_GND->REG_GND
TPA
S_C_I/O
XS_JACK_IN
SE_2.8V
LANC_SIG
REG_GND
USB_D+
NTPA
REG_GND
VIDEO_I/O
REG_GND
PS_LI
YS_V
S_Y_I/O
XLANK_JACK_IN
NTPB
YS_LI
AV_JACK_IN
TPB
REG_GND
PS_V
AU_LINE_I/O_R
KEY_AD5
USB_VCC->USB_DET
LANC_DC
REG_GND
USB_D-
REG_GND
VC-280 BOARD(1/3)
LENZBLOCK
H
2 3 12
J
179
G
11
E
C
10
K
14136
B
7
I
D
F
155
L
84 16
16
FLEX
IBLE
FLEX
IBLE
CAPSTAN MOTOR LOADING MOTOR,MODE SWITCH,T/S REEL SENSOR DRUM MOTOR VIDEO HEAD
FLEX
IBLE
(FOR CHECK)
J5301
J5302
CN5351
CN5352
CN5351
DCR-TRV16/TRV16E/TRV18/TRV18E/TRV116E/TRV118E
COVERCOVER 4-2. SCHEMATIC DIAGRAMS 4-3. PRINTED WIRING BOARDS4-2. SCHEMATIC DIAGRAMS 4-3. PRINTED WIRING BOARDS
4-3 4-4
FRAME SCHEMATIC DIAGRAM (2/3)
FRAME SCHEMATIC DIAGRAM (2/3)
20P
CN
4001
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20
24P
CN
4003
123456789101112131415161718192021222324
20P
CN
4201
1234567891011121314151617181920
6PC
N46
01
123456
16P
CN
6102
1V
DD
2V
SS
3V
ST
4V
CK
5S
TB
6EN
7D
WN
8R
GT
9H
ST
10H
CK
2
11H
CK
1
12B
LK
13V
B
14V
R
15V
G
16C
OM
20P
CN
6101
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20
24P
CN
5902
123456789101112131415161718192021222324
8PCN5903
1
2
3
4
5
6
7
8
CN5901 4P
1
2
3
4
6PCN6001
1
2
3
4
5
6
100P
CN
1007
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100
100P
CN
4002
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100
1
A
SH
OE_
MT_
GN
D
SH
OE_
UN
REG
SH
OE_
UN
REG
_GN
D
SH
OE_
ID2
SH
OE_
UN
REG
_GN
D
SH
OE_
ID1
SH
OE_
CO
NT_
AD
PR
T_H
EAD
_UN
REG
SH
OE_
UN
REG
TXD
LAN
C_S
IG
RX
D
SH
OE_
MT_
GN
D
SC
K
SH
OE_
MIC
_L
SH
OE_
MIC
_GN
D
HD
S
STB
Y_O
N
PR
T_H
EAD
_UN
REG
SH
OE_
UN
REG
_GN
D
REG
_GN
D
MF_
A
MIC
_GN
D
EXT_
MIC
_L
HP
_R_O
UT
A_4
.6V
MF_
B
MIC
_GN
D
XF_
TALL
Y_L
ED
KEY
_AD
6
INT_
MIC
_L
MIC
_GN
D
AU
_2.8
V
REG
_GN
D
HP
_L_O
UT
HP
_JA
CK
_IN
REG
_GN
D
NS
_LED
_K
N.C
. (M
F_LE
D)
EXT_
MIC
_R
MIC
_GN
D
INT_
MIC
_R
SIR
CS
_SIG
NS
_LED
_A
W_L
ED_4
.75V
VS
T
VR
VC
K
LED
_ON
/OFF
EVF_
GN
D
XTA
LLY
_LED
BLK
EVF_
GN
D
VG
STB
ENEVF_
GN
D
HC
K1
LED
_DA
HC
K2
EVF_
VD
D
HS
T
CO
M
VB
BAT
T_U
NR
EG
BAT
T/X
EXT
BAT
T_S
IG
BAT
T_G
ND
AC
V_U
NR
EG
AC
V_G
ND
ENVR
VS
T
HS
T
LED
_DA
EVF_
GN
D VB
HC
K2
EVF_
GN
D
HC
K1
STB
XTA
LLY
_LED BLK
EVF_
VD
D
LED
_ON
/OFF
VC
K
W_L
ED_4
.75V
CO
M VG
EVF_
GN
DHP
_L_O
UT
MIC
_GN
D
SIR
CS
_SIG
MF_
A
MIC
_GN
D
HP
_R_O
UT
MIC
_GN
D
REG
_GN
D
INT_
MIC
_L
NS
_LED
_K
REG
_GN
D
KEY
_AD
6
INT_
MIC
_R
NS
_LED
_A
A_4
.6V
MIC
_GN
D
EXT_
MIC
_R
HP
_JA
CK
_IN
REG
_GN
D
XF_
TALL
Y_L
ED
AU
_2.8
V
MF_
B
EXT_
MIC
_L
N.C
. (M
F_LE
D)
REG_GND
MF_A
AU_2.8V
XF_TALLY_LED
REG_GND
KEY_AD6
A_4.6V
MF_BINT_MIC_R
INT_MIC_L
GND
GND
REG_GND
A_4.6V
AU_2.8V
XF_TALLY_LED
MF_B
MF_A
VA-117 BOARD(1/2)
MA-409BOARD
LB-077 BOARD
FP-437
R
FB-219BOARDFP
-444
FP-435FP-436
J5901
VD
_SC
K
DR
UM
_VS
PB
_IN
_R
IC41
01_O
UT
D_1
.5V
REG
_GN
D
AG
C_C
ON
T
FAS
T_C
HA
RG
E
A_4
.75V
MT_
GN
D
REG
_GN
D
MF_
B
HO
TSH
OE_
ID2
REC
_OU
T_L
MT_
GN
D
REG
_GN
D
BEE
P_I
N
REG
_1.5
V
BAT
T_S
IG
IC41
01_O
UT
DR
UM
_VS
DR
UM
_ER
RO
R
ZOO
M_M
IC_C
ON
T
KEY
_AD
6
BAT
T_U
NR
EG
D_1
.5V
AU
_LIN
E_I/
O_L
EVF_
G/B
W_Y
VD
_SO
RP
_4.7
5V
XC
S_I
C41
01
XC
S_A
U1
CA
M_-
6.5V
REG
_1.5
V
HS
_SC
K
HS
_HD
S
XV
SP
_SC
K
A_2
.8V
MF_
A
VC
O
XV
IDEO
_IN
BAT
T_X
EXT
INIT
_CH
AR
GE_
ON
IC21
01_O
UT G
XF_
TALL
Y_L
ED
SIR
CS
_PW
M
SH
OE_
ON
HO
TSH
OE_
ID1
MT_
5V
VID
EO_I
/O
EXT_
MIC
_JA
CK
S_C
_I/O
EVF_
R
IC23
01_R
EVF_
B
SH
OE_
CO
NT_
AD
CA
M_D
D_O
N
XM
IC_M
ON
O
A_4
.75V
HS
_TX
D
D_2
.8V
CA
P_E
RR
OR
IC23
01_L
D_1
.9V
HS
_RX
D
EXT_
STR
OB
O
PLL
_1.5
V
IR_O
N
EP_1
3.3V
VTR
_UN
REG
REG
_GN
D
A_2
.8V
CA
P_V
S
XR
ST_
VTR
CA
P_V
S
PB
_IN
_L
PA
NEL
_XH
D
CA
M_1
2V
SD
C_I
N
IC21
01_O
UT
MF_
LED
XC
S_E
VF
PA
NEL
_XV
D
REG
_GN
D
SIR
CS
_SIG
REG
_GN
D
D_2
.8V
AU
_LIN
E_I/
O_R
S_V
_I/O
REG
_GN
D
REC
_OU
T_R
XA
UD
IO_I
N
VTR
_DD
_ON
VS
P_S
O
MT_
5V
LAN
C_S
IG
AC
C_C
ON
T
HP
_JA
CK
_IN
D_2
.8V
REC
_OU
T_R
S_C
_I/O
MF_
A
XF_
TALL
Y_L
ED
VS
P_S
O
AC
C_C
ON
T
CA
M_-
6.5V
REG
_GN
D
IC21
01_O
UT
D_2
.8V
XC
S_E
VF
XC
S_I
C41
01
DR
UM
_VS
PLL
_1.5
V
A_4
.75V
IC43
01_L
PB
_IN
_R
D_2
.8V
HO
TSH
OE_
ID2
XR
ST_
VTR
REG
_GN
D
SH
OE_
CO
NT_
AD
VD
_SO
EVF_
B
VC
O
IC41
01_O
UT
AU
_LIN
E_I/
O_L
XC
S_A
U1
EP_1
3.3V
EXT_
MIC
_JA
CK
VD
_SC
K
MF_
B
BAT
T_S
IG
VID
EO_I
/O
D_1
.9V
RP
_4.7
5V
IC43
01_R
MT_
5V
EVF_
R
A_4
.75V
FAS
T_C
HA
RG
E
DR
UM
_VS
CA
M_D
D_O
N
IR_O
N
D_1
.5V
REG
_GN
D
A_2
.8V
EXT_
STR
OB
O
IC41
01_O
UT
REG
_GN
D
REG
_GN
D
EVF_
G/B
W_Y
CA
P_V
S
DR
UM
_ER
RO
R
SIR
CS
_SIG
HS
_RX
D
REG
_GN
D
REG
_1.5
V
AU
_LIN
E_I/
O_R
ZOO
M_M
IC_C
ON
TG
HO
TSH
OE_
ID1
REG
_GN
D
VTR
_UN
REG
HS
_SC
K
LAN
C_S
IG
REG
_1.5
V
REC
_OU
T_L
A_2
.8V
CA
P_E
RR
OR
MT_
GN
D
SD
C_I
N
PA
NEL
_XH
D
D_2
.8V
XM
IC_M
ON
O
BAT
T_U
NR
EG
HP
_JA
CK
_IN
CA
P_V
S
BEE
P_I
N
PB
_IN
_L
BAT
T_X
EXT
MF_
LED
PA
NEL
_XV
D
SH
OE_
ON
HS
_HD
S
SIR
CS
_PW
M
HS
_TX
D
KEY
_AD
6
XA
UD
IO_I
N
D_1
.5V
INIT
_CH
AR
GE_
ON
XV
SP
_SC
K
AG
C_C
ON
T
CA
M_1
2V
IC21
01_O
UT
S_Y
_I/O
XV
IDEO
_IN
VTR
_DD
_ON
MT_
GN
D
MT_
5V
BT901
LCD903
VC-280 BOARD(2/3)
MIC901
H
2 3 129
G
11
E
C
10 14136
B
7
I
D
F
5 84
16
FLEXIBLE
FLEX
IBLE
L
(HEADPHONE)
MIC(PLUG IN POWER)
INTELLIGENT ACCESSORY SHOE
FLEXIBLE FLEXIBLE
COLOR LCD UNIT
DC INBATTERYTERMINAL
BOARD TO BOARD
15p(DCR-TRV18/TRV18E/TRV118E) 8p(DCR-TRV16/TRV16E/TRV116E)
J5902
DCR-TRV16/TRV16E/TRV18/TRV18E/TRV116E/TRV118E
COVERCOVER 4-2. SCHEMATIC DIAGRAMS 4-3. PRINTED WIRING BOARDS4-2. SCHEMATIC DIAGRAMS 4-3. PRINTED WIRING BOARDS
4-5 4-6
FRAME SCHEMATIC DIAGRAM (3/3)
FRAME SCHEMATIC DIAGRAM (3/3)
28P
CN
1005
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28
12P
CN
4004
123456789101112
2PCN5205
1SP(+)
2SP(-)
40P
CN
5202
12345678910111213141516171819202122232425262728293031323334353637383940
8PC
N52
04
1 2 3 4 5 6 7 8
8PCN5207
1 EXECUTE
2 GND
3 DIAL_A
4 DIAL_B
5 BACK_LIGHT
6 EXPOSURE
7 GND
8 GND
20P
CN
5203
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20
24P
CN
5501
123456789101112131415161718192021222324
10PCN5601
1 LED_GND
2 LED
3 BL_LOW
4 N.C.
5 N.C.
6 N.C.
7 N.C.
8 N.C.
9 N.C.
10 BL_HIGH
6PC
N56
53
123456
8PC
N56
51
1 2 3 4 5 6 7 8
20P
CN
5652
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20
20P
CN
5654
1234567891011121314151617181920
8PC
N00
1
12345678
18P
CN
5201
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18
20P
CN
1008
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20
1
A
10P
CN
001
1 2 3 4 5 6 7 8 9 10
KEY
_AD
3
PA
NEL
_G
XH
D_O
UT
HI_
XR
ESET
BAT
T_LI
_3V
MA
KER
_CH
ECK
KEY
_AD
2
VD
_SO
XR
ST_
VTR
PA
NEL
_XV
D
PA
NEL
_B
CO
M_O
UT
LCD
_CO
M/X
DAT
A
KEY
_AD
1
REG
_GN
D
PA
NEL
_R
XO
SD
_SC
K
XC
S_L
CD
KEY
_AD
4
VG
PA
NEL
_XH
D
DIA
L_A
XC
S_L
CD
_DR
IVER
OS
D_S
O
VD
_SC
K
EVER
_3.0
V
REG
_GN
D
DIA
L_B
BL_
CO
NT
PA
NEL
_4.7
5V SP
-
BL_
GN
D
PA
NEL
_-15
.3V
SE_
GN
D
PA
NEL
_13.
3V
BL_
REG
BL_
REG
BL_
GN
D
PA
NEL
_2.8
V
BL_
CO
NT
VD
_SC
K
PA
NEL
_R
HI_
EVER
_SO
PA
NEL
_XV
D
VD
_SO
XR
ST_
VTR
BL_
REG
KEY
_AD
2_P
MA
KER
_CH
ECK
PA
NEL
_B
HI_
EVER
_SC
K
PA
NEL
_B
XC
S_L
CD
PA
NEL
_XV
D
REG
_GN
D
PA
NEL
_G
KEY
_AD
4
PA
NEL
_-15
.3V
PA
NEL
_13.
3V
PA
NEL
_G
EVER
_3.0
V
LCD
_CO
M/X
DAT
A
KEY
_AD
1
XC
S_L
CD
_DR
IVER
KEY
_AD
3
HI_
EVER
_SC
K
EVER
_3.0
V
BL_
GN
D
SE_
GN
D
BL_
GN
D
SP
+
XH
D_O
UT
REG
_GN
D
PA
NEL
_-15
.3V
XC
S_L
CD
PA
NEL
_XH
D
BL_
REG
PA
NEL
_4.7
5V
EP_1
3.3V
PA
NEL
_XH
D
VD
_SO
VG
MA
KER
_CH
ECK
BL_
CO
NT
XH
D_O
UT
BL_
REG
SE_
GN
D
EP_2
.8V
CO
M_O
UT
PS
IG/P
AN
EL_C
OM
DIA
L_B
VD
_SC
K
PA
NEL
_2.8
V
SP
-
EP_4
.75V
DIA
L_A
BAT
T_LI
_3V
HI_
EVER
_SO
LCD
_CO
M/X
DAT
A
HI_
XR
ESET
XC
S_L
CD
_DR
IVER
XR
ST_
VTR
BL_
GN
D
REG
_GN
D
VG
KEY
_AD
2
PA
NEL
_R
VS
H3V V
B
SP
D
EX1
SP
S
GN
D
CLS EX
2
PS
G
PS
S2
VG
L
MO
1
RES
VG
H
PS
S1
VR
VS
H5V
CTR
GN
D
CLDV
G
MO
2
VC
OM
VG
LAC
BL_
GN
D
PA
NEL
_B
PA
NEL
_REV
VD
_SC
K
XC
S_L
CD
_DR
IVER
PS
IG/P
AN
EL_C
OM
MA
KER
_CH
ECK
GN
D
BL_
REG
EP_1
3.3V
PA
NEL
_R
LCD
_CO
M/X
DAT
A
GN
D
GN
D
VG
PA
NEL
_XV
D
N.C
.
EP_4
.75V
HI_
EVER
_SO
PA
NEL
_-15
.3V
EVER
_3.0
V
XR
ST_
VTR
PA
NEL
_G
HI_
EVER
_SC
K
REG
_GN
D
BL_
CO
NT
VD
_SO
PA
NEL
_REV
XH
D_O
UT
EP_2
.8V
SE_
GN
D
KEY
_AD
2_P
XC
S_L
CD
PA
NEL
_XH
D
CO
M1
SEG
11
SEG
6
SEG
4
SEG
12
SEG
15
SEG
16
SEG
2
SEG
10
CO
M3
CO
M4
SEG
7
SEG
1
SEG
14
SEG
13
SEG
3
SEG
8
SEG
9
CO
M2
SEG
5
MS
_BS
MS
_VC
C
MS
_SC
LK
MS
_DIO
MS
_IN
SER
T
GN
D
GN
D
MS
_VC
C
FP-442
CK-108BOARD
PD-161 BOARD
FP-434
PV-138 HARNESSM
S_P
LAY
MP
EG_P
LAY
MS
_IN
DEX
MEM
OR
Y_M
IX
REG
_GN
D
MS
_-
DIS
PLA
Y
REG
_GN
D
MS
_+
VO
L_-
MEN
U
MS
_DEL
ETE
REC
END
_SEA
RC
H
VO
L_+
AU
DIO
_DU
B
PB
_ZO
OM
GN
D
MS
_VC
C
MS
_VC
C
GN
D
MS
_DIO
XP
HO
TO_F
REE
ZE
KEY
_AD
0
XV
TR_M
OD
E_S
W
XP
HO
TO_S
TBY
_SW
GN
D
ZOO
M_A
D
MS
_SC
LK
XC
AM
_STB
Y_S
W
MS
_IN
SER
T
D_2
.8V
AC
CES
S_L
ED
MS
_BS
GN
D
XS
/S_S
W
D_2
.8V
SP
+
LCD902
PANELREVERSE SW
LCD901
CONTROLSWITCHBLOCK
SHEET KEY
CONTROL SWITCH BLOCK
VC-280 BOARD(3/3)
SP901SPEAKER
VA-117 BOARD(2/2)
H
2 3 12
J
9
G
11
E
C
10 14136
B
7
I
D
F
155 84
16
BACK LIGHT
2.5INCH COLOR LCD UNIT
FLEXIBLE
CHARACTOR DISPLAY UNIT
CONTROL SWITCHBLOCK
(KP-CX2670)
(SH-CX2670)
BT5201(LITHIUM BATTEY)
(PS-CX2670)
MS
_DIO
MS
_BS
MS
_VC
C
MS
_IN
SER
T
MS
_VC
C
MS
_SC
LK
GN
D
GN
D
N.C
.
N.C
.
FP-438FLEXIBLE
MEMORYSTICKCONNECTOR
FLEXIBLE
ND901
DCR-TRV18/TRV18E/TRV118E MODEL
DCR-TRV16/TRV16E/TRV18/TRV18E/TRV116E/TRV118E
COVERCOVER 4-2. SCHEMATIC DIAGRAMS 4-3. PRINTED WIRING BOARDS4-2. SCHEMATIC DIAGRAMS 4-3. PRINTED WIRING BOARDS
4-7
(Measuring conditions voltage and waveform)• Voltages and waveforms are measured between the measure-
ment points and ground when camera shoots color bar chart ofpattern box. They are reference values and reference wave-forms. *(VOM of DC 10 MΩ input impedance is used.).
• Voltage values change depending upon input impedance of VOMused.) *
1. Connection
2. Adjust the distance so that the output waveform of Fig. a andthe Fig. b can be obtain.
Yello
w
A AB BA=B
Fig. a (Video output terminal output waveform)
Fig.b (Picture on monitor TV)
Electron beam scanned frame
CRT picture frame
H
Cya
nG
reen
Whi
teM
agen
ta
Red
Blu
e
Yello
wC
yan
Gre
enW
hite
Mag
enta
Red
Blu
e
THIS NOTE IS COMMON FOR WIRING BOARDS AND SCHEMATIC DIAGRAMS(In addition to this, the necessary note is printed in each block)
Transistor Diode
When indicating parts by reference number, please includethe board name.
(For printed wiring boards)• b: Pattern from the side which enables seeing.
(The other layers' patterns are not indicated.)• Through hole is omitted.• Circled numbers refer to waveforms.• There are few cases that the part printed on diagram isn’t
mounted in this model.• Chip parts.
(For schematic diagrams)• All capacitors are in µF unless otherwise noted. p: pF.
50V or less are not indicated except for electrolytics andtantalums.
• Chip resistors are 1/10W unless otherwise noted.kΩ=1000Ω, MΩ=1000kΩ.
• Caution when replacing chip parts.New parts must be attached after removal of chip.Be careful not to heat the minus side of tantalum capacitor, Be-cause it is damaged by the heat.
• Some chip part will be indicated as follows.Example C541 L452
22U 10UHTA A 2520
• Constants of resistors, capacitors, ICs and etc with XX indicatethat they are not used.In such cases, the unused circuits may be indicated.
• All variable and adjustable resistors have characteristic curve B,unless otherwise noted.
• Signal nameXEDIT → EDIT PB/XREC → PB/REC
• 2 : non flammable resistor• 1 : fusible resistor• C : panel designation• A : B+ Line *• B : B– Line *• J : IN/OUT direction of (+,–) B LINE. *• C : adjustment for repair. *• Circled numbers refer to waveforms. ** Indicated by the color red.
External dimensions (mm)Temperature characteristics
Kinds of capacitor
C
B E
56 4
21 3
54 6
23 1
4 5
23 1
1 2
45 3
3
2 1
3
2 1
3
2 1
E B
C C
2 1
3 4
Note :The components identified bymark 0 or dotted line with mark0 are critical for safety.Replace only with part numberspecified.
Note :Les composants identifiés parune marque 0 sont critiquespour la sécurité.Ne les remplacer que par unepièce portant le numéro spécifié.
1.5 m
Front of the lens
Pattern box
DCR-TRV16/TRV16E/TRV18/TRV18E/TRV116E/TRV118E
COVERCOVER
LinkLink
4-2. SCHEMATIC DIAGRAMS
VA-117 BOARD (6/6) (VIDEO I/O)
VA-117 BOARD (5/6) (CHARGE)
VA-117 BOARD (4/6) (DC-DC CONVERTER)
VA-117 BOARD (3/6) (MIC AMP)
FP-100, FP-228, FP-102 FLEXIBLE BOARD (MODE SWITCH, DEW SENSOR, TAPE TOP/END SENSOR, S/T REEL)
VA-117 BOARD (2/6) (AUDIO)
VA-117 BOARD (1/6) (RGB DRIVE, TG)
PD-161 BOARD (2/2) (LCD DRIVE, BACK LIGHT)
MA-409 BOARD (MIC IN, HP JACK, REMOTE CONTROL RECEIVER, SWITCH)
PD-161 BOARD (1/2)(RGB DRIVE, TIMING GENERATOR)
JK-217 BOARD (STEADY SHOT, A/D IN/OUT)
JK-218 BOARD (DIGITAL IN/OUT)
FB-219 BOARD (MANUAL FOCUS SENSOR)
CK-108 BOARD (SWITCH, CONNECTOR)
CONTROL SWITCH BLOCK (PS-CX2670)
LB-077 BOARD (EVF, EVF BACK LIGHT)
CD-365 BOARD (CCD IMAGER)
VA-117 BOARD (6/6) (VIDEO I/O)
VA-117 BOARD (5/6) (CHARGE)
VA-117 BOARD (4/6) (DC-DC CONVERTER)
VA-117 BOARD (3/6) (MIC AMP)
FP-100, FP-228, FP-102 FLEXIBLE BOARD (MODE SWITCH, DEW SENSOR, TAPE TOP/END SENSOR, S/T REEL)
VA-117 BOARD (2/6) (AUDIO)
VA-117 BOARD (1/6) (RGB DRIVE, TG)
PD-161 BOARD (2/2) (LCD DRIVE, BACK LIGHT)
MA-409 BOARD (MIC IN, HP JACK, REMOTE CONTROL RECEIVER, SWITCH)
PD-161 BOARD (1/2)(RGB DRIVE, TIMING GENERATOR)
JK-217 BOARD (STEADY SHOT, A/D IN/OUT)
JK-218 BOARD (DIGITAL IN/OUT)
FB-219 BOARD (MANUAL FOCUS SENSOR)
CK-108 BOARD (SWITCH, CONNECTOR)
CONTROL SWITCH BLOCK (PS-CX2670)
LB-077 BOARD (EVF, EVF BACK LIGHT)
CD-365 BOARD (CCD IMAGER)
WAVEFORMSCOMMON NOTE FOR SCHEMATIC DIAGRAMS WAVEFORMSCOMMON NOTE FOR SCHEMATIC DIAGRAMS
DCR-TRV16/TRV16E/TRV18/TRV18E/TRV116E/TRV118E
COVERCOVER
4-2. SCHEMATIC DIAGRAMS
4-9 4-10 CD-365/LB-077
4-2. SCHEMATIC DIAGRAMS LB-077 BOARDCD-365 BOARD4-2. SCHEMATIC DIAGRAMS CD-365 BOARD LB-077 BOARD
For Schematic Diagram• Refer to page 4-67 for printed wiring board.• Refer to page 4-89 for waveforms.
R-6
.2/P
0
R-6
.2/P
0
R-0
.3/P
0
R-0
.3/P
0
R7.
4P
0
R12
.2P
0
R-6
.5/P
0.4
R7.
3/P
0
R1.
4/P
0
R1.
6/P
0 0
R8.
4/P
0
R12.2P0
R7.6/P0
5 4 31 2
6
NO MARK:REC/PB MODE R :REC MODE P :PB MODE
:DCR-TRV16/TRV18:DCR-TRV16E/TRV18E/TRV116E/TRV118E
A10V
TA
10uC5001
*IC
5001
V4
1
V3
2
V2
3
V1
4
V_H
OLD
5
V_D
RA
IN
6
VD
D
7
CC
D_O
UT
8
GN
D
9
RG
10
H1
11
H2
12
SU
B
13
VL
14 LN5001
GND
2SC
4178
-F13
F14-
T1Q
5001
CH
C500210p
16PCN5001
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
B20V
TA
10uC5004
B0.01uC5003
220uHL5001
3300R5001
6PCN5002
1
2
3
4
5
6
XXR5002
S202
1A1
3A2
2B1
4B2
XXD201
R2021500
S203
1A1
3A2
2B1
4B2
LND210
S201
R2011200
1
A
RG
RG
H1
H1
H2
H2
V3
KEY_AD0
CCD_GND
H1
VSHT
V2
H2
CCD_OUT
-6.5V
V4
12V
V_DRAIN
RG
CCD_GND
V1
GND
GND
GND
GND
KEY_AD0
XEJECT_SW
XEJECT_SW
CCD IMAGER
IC5001
EDITSERACH +
EDITSERACH -
(EJECT SW)
FP-443 FLEXIBLE
TOVC-280 BOARD(1/15)CN1401
(PAGE 4-38)
TROUGH THE FP-439 FLEXIBLE
BU
FFER
2 5
E
3
F
4
C
9
D
B
876
16
CD-365 BOARD
XX MARK:NO MOUNT
CCD IMAGER
CHROMA
VIDEO SIGNAL
SIGNAL PATH
Y
REC
Y/CHROMA
PB
IC5001ICX220BK-13ICX221BK-13
Precautions Upon Replacing CCD imager
The CD-365 board mounted as a repair part is not equipped
•
•
old one and mount it onto the new one.
As the CCD imager may be damaged by static electricity from
•
its structure, handle it carefully like for the MOS IC.
nor exposed to strong light.
In addition, ensure that the receiver is not covered with dusts
When replacing this board, remove the CCD imager from the
adjustments for the camera section.
If the CCD imager has been replaced, carry out all the
with a CCD imager.
1.0 1.4
0.3
1.00.4
4.70.3
0.3
4.70
4.7
0
2.8
NO MARK:REC/PB MODE
33kR6105
± 0.5%22
R6106NJM2125F(TE2)IC6101
12
3 45
16PCN6102
1 VDD
2 VSS
3 VST
4 VCK
5 STB
6 EN
7 DWN
8 RGT
9 HST
10 HCK2
11 HCK1
12 BLK
13 VB
14 VR
15 VG
16 COM
20PCN6101
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
R6101XX
TH61016.8k
NSCW100-T39D6102
3300R6104
XXD6101
± 0.5%180k
R6102
2.2uF
C6102
HN1B04FE-Y/GR(TPLR3)Q6102
3
5
4 6
2
1
± 0.5%33k
R6103
RN4983FE(TPLR3)Q6101
3
5
4
6
2
1
C61010.1u
1
A
EVF_GND
EVF_VDD
XTALLY_LED
VB
VST
VG
EVF_GND
W_LED_4.75V
BLK
VR
STB
LED_DA
EN
LED_ON/OFF
HST
EVF_GND
COM
VCC
HCK1
HCK2
VCK
LED BACKLIGHT DRIVER
IC6101 (BACKLIGHT)
LED DRIVE
LED SWITCH
TOVA-117 BOARD(1/6)CN4201
( THROUGHTHE FP-435 FLEXIBLE )
(PAGE 4-24)
LCD903
COLOREVF UNIT
EVF,EVF BACK LIGHTLB-077 BOARD
XX MARK:NO MOUNT
E
F
5
C
3 42
B
6
D
16VIDEO SIGNAL
YCHROMA
PB
SIGNAL PATH
REC
Y/CHROMA
For Schematic Diagram• Refer to page 4-75 for printed wiring board.
DCR-TRV16/TRV16E/TRV18/TRV18E/TRV116E/TRV118E
COVERCOVER
4-11 4-12MA-409/FB-219
4-2. SCHEMATIC DIAGRAMS MA-409 BOARD FB-219 BOARD4-2. SCHEMATIC DIAGRAMS MA-409 BOARD FB-219 BOARD
For Schematic Diagram• Refer to page 4-71 for printed wiring board of MA-409 board.• Refer to page 4-73 for printed wiring board of FB-219 board.
0.12.3
1.1 0.1
NO MARK:REC/PB MODE
4.64.6
LN5901
A
B0.01u
C5901
FB5903 0uHJ5901
VD5902 VD5904
FB5904 0uH
CN5901 4P
1
2
3
4
24PCN5902
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
8PCN5903
1
2
3
4
5
6
7
8
FB5901 0uH
VD5903
FB5902 0uH
VD5901J5902
CL-310IRS-X-TUD5902
47R5901
10u6.3VTA
C5902
CL-310IRS-X-TUD5901
MA111-(K8).S0D5903
SBX3055-01IC5901
12
4 3
XXD5904
1 23
D5905UDZSTE-178.2B
GP1S092HCPIPH6001
6PCN6001
1
2
3
4
5
6
GP1S092HCPIPH6002
SML-310LTT86D6001
330R6003
R60010
680R6002
R3011200
R3021500
S301
1A1
3A2
2B1
4B2
S302
1
2
3
4
1
A
INT_MIC_L
EXT_MIC_L
INT_MIC_R
EXT_MIC_R
HP_JACK_IN
HP_L_OUT
HP_R_OUT
EXT_MIC_L
EXT_MIC_R
HP_L_OUT
HP_JACK_IN
HP_R_OUT
INT_MIC_L
INT_MIC_R
XF_TALLY_LED
MF_B
MF_A
MF_A
MF_B
XF_TALLY_LED
KEY_AD6
KEY_AD6
SIRCS_SIG
XF_TALLY_LED
NS_LED_A
A_4.6V
NS_LED_K
INT_MIC_L
INT_MIC_R
GND
GND
A_4.6V
XF_TALLY_LED
HP_R_OUT
HP_L_OUT
HP_JACK_IN
INT_MIC_L
MIC_GND
AU_2.8V
MIC_GND
REG_GND
MF_A
MF_B
REG_GND
REG_GND
MF_A
MF_B
KEY_AD6
KEY_AD6
AU_2.8V
OUT VCC
GND GND
N.C. (MF_LED)
REG_GND
INT_MIC_R
MIC_GND
EXT_MIC_L
EXT_MIC_R
MIC_GND
REG_GND
A_4.6V
AU_2.8V
REG_GND
XF_TALLY_LED
MF_B
MF_A
L
R
MIC901
MIC(PLUG IN POWER)
(HEADPHONES)
REMOTE CONTROL RECEIVER
IC5901
TOVA-117 BOARD(3/6)CN4003
( THROUGH THEFP-437 FLEXIBLE )
(PAGE 4-27)
FADER FOCUS(INFINITY)
FP-444 FLEXIBLE
MANUAL FOCUS SENSORFB-219 BOARD
(TALLY)
SIGNAL PATH
PB
AUDIOSIGNAL
REC
H
2 3 129
G
11
E
C
106
B
7
D
F
5 84
I
MA-409 BOARDMIC IN,HP JACK,REMOTE CONTROL RECEIVER,SWITCHXX MARK:NO MOUNT
16
(NS LED)
(NS LED)
DCR-TRV16/TRV16E/TRV18/TRV18E/TRV116E/TRV118E
COVERCOVER
4-13 4-14 JK-217/JK-218
4-2. SCHEMATIC DIAGRAMS JK-217 BOARD JK-218 BOARD4-2. SCHEMATIC DIAGRAMS JK-217 BOARD JK-218 BOARD
For Schematic Diagram• Refer to page 4-69 for printed wiring board of JK-217 board.• Refer to page 4-70 for printed wiring board of JK-218 board.
(TRV16/TRV16E:E,HK,AUS,CH/TRV18/TRV18E:E,HK,AUS,CH,JE/TRV116E/TRV118E)
(TRV16E:AEP,UK,EE,NE/TRV18E:AEP,UK,EE,NE)
0R5304
VD5303
FB5310 0uH
FB53090uH
VD5304
VD5306
0R5302
0R5301
VD5301
VD5305
VD5302
01ZA8.2(TPL3)D5302
1 23
J5301
1 SIG
2 LANC_DC3 GND
4 232C_TD
5 JACK_IN
Y
GG
C
J5302
2 CGND
1 YGND
4 C
3 Y
6 S1
5 S2
7 V8 AUL
9 AUR10GND11S
XXC5302
XXC5301
LN5301
CH_GND
0R5303
UDZSTE-178.2BD5301
FB53010uH
FB53070uH
FB5308 0uH
FB53050uH
FB53040uH
FB53
020u
H
FB53030uH
20PCN5305
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
0R5305
SE5302
1 234
SE5301
1 234
CN5351 5P
1VCC
2D-
3D+
4ID
5USB GND
S5351
1A
2B
10kR5352
R5355XX
UDZSTE-178.2BD5352
21
CL5351
CH_GND
12PCN5353
1
2
3
4
5
6
7
8
9
10
11
12
01ZA8.2(TPL3)D5351
1 23
R5354XX
CL5352
CH_GND
4PCN5352
1
2
3
4
LF53510uH
R5353XX
UDZSTE-178.2BD5353
21
1SS357(T3SONY1)D5354
LF53520uH
10kR5351
R5356XX
30PCN5354
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
1
A
V_JACK_IN
S_C_I/O
AUDIO_L_I/O
AUDIO_R_I/O
VIDEO_I/O
S_Y_I/O
XS_JACK_IN
S_GND
SE_2.8V
PS_V
LANC_SIG
REG_GND
REG_GND
XS_JACK_IN
PS_LI
AU_LINE_I/O_L
S_C_I/O
XLANK_JACK_IN
REG_GND
VIDEO_I/O
S_Y_I/O
AV_JACK_IN
REG_GND
YS_V
LANC_DC
REG_GND
AU_LINE_I/O_R
YS_LI
Vcc
Vout
Vref
GND
GND Vout
Vref Vcc
TPB
USB_DET
NTPA
TPA
REG_GND
REG_GND
KEY_AD5
TPA
REG_GND
USB_D+
TPB
REG_GND
NTPB
USB_D-
NTPB
NTPA
XLANK_JACK_IN
XS_JACK_IN
KEY_AD5
USB_GND->REG_GND
REG_GND
AU_LINE_I/O_L
PS_LI
YS_V
REG_GND
TPA
TPB
USB_D-
LANC_DC
AV_JACK_IN
S_C_I/O
YS_LI
VIDEO_I/O
NTPA
USB_D+
REG_GND
SE_2.8V
PS_V
AU_LINE_I/O_R
REG_GND
LANC_SIG
USB_VCC->USB_DET
REG_GND
NTPB
REG_GND
S_Y_I/O
(PITCH SENSOR)
(YAW SENSOR)
S VIDEO(IN/OUT)
AUDIO/VIDEO (IN/OUT)
LANC
XX MARK:NO MOUNT
JK-217 BOARDSTEADY SHOT,A/D IN/OUT
CHROMA
REC
Y SIGNAL
PB
Y/CHROMAAUDIO
VIDEO SIGNAL
SIGNAL PATH
(USB)
SUPER NS
DV IN/OUT
XX MARK:NO MOUNT
DIGITAL IN/OUTJK-218 BOARD
FP-445 FLEXIBLE
TOVC-280 BOARD(11/15)CN1006
(PAGE 4-57)
H
2 3 12
J
9
G
11
E
C
10 14136
B
7
I
D
F
5 84
16
S VIDEO(OUT)
AUDIO/VIDEO (OUT)
DV OUT
Note
Note
NoteS VIDEO (IN/OUT) AUDIO/VIDEO (IN/OUT)
S VIDEO (OUT) AUDIO/VIDEO (OUT)
Note
Note
(TRV16/TRV16E:E,HK,AUS,CH/TRV18/TRV18E:E,HK,AUS,CH,JE/TRV116E/TRV118E)
(TRV16E:AEP,UK,EE,NE/TRV18E:AEP,UK,EE,NE)
DV IN/OUT
DV OUT • AbbreviationEE : East European modelNE : North European modelHK : Hong Kong model
AUS : Australian modelCH : Chinese modelJE : Tourist model
DCR-TRV16/TRV16E/TRV18/TRV18E/TRV116E/TRV118E
COVERCOVER
4-15 4-16CK-108
4-2. SCHEMATIC DIAGRAMS CK-108 BOARD SIDE A CK-108 BOARD SIDE B4-2. SCHEMATIC DIAGRAMS CK-108 BOARD SIDE A CK-108 BOARD SIDE B
For Schematic Diagram• Refer to page 4-77 for printed wiring board.
(DCR-TRV18/TRV18E/TRV118E)
(DCR-TRV16/TRV16E;E,HK,AUS,CH/TRV18/TRV18E:E,HK,AUS,CH,JE/TRV116E/TRV118E)
2PCN5205
1SP(+)
2SP(-)
01ZA8.2(TPL3)D5205
1 2
301ZA8.2(TPL3)
D5206
1 2
3
LN5202
CH GND
40PCN5202
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
18PCN5201
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
S520712
34
3900R5219
3900R5220
1200R5209
2200R5217
1500R5213
LN5201
CH GND
D520101ZA8.2(TPL3)
1 2
3
D52
03U
DZS
TE-1
78.2
B 2
1
S5203
1
3
2
401ZA8.2(TPL3)D5204
1 2
3
1kR5201
8PCN5204
1
2
3
4
5
6
7
8
20PCN5203
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
S5201
1
3
2
4
S5202
1
3
2
4
S5204
1
3
2
4
S5205
1
3
2
4
S5206
1
3
2
4
8200R5223
8200R5226
BT5201
C5201XX
C5202XX
8PCN5207
1
2
3
4
5
6
7
8
0R5227
XXC5203
0R5228
XXD5208
XXD5207
S114
1
3
2
4
S102
1
3
2
4
S110
1
3
2
4
S108
1
3
2
4
S116
1
3
2
4
S111
1
3
2
4
S113
1
3
2
4
S107
1
3
2
4
S103
1
3
2
4
S115
1
3
2
4
S101
1
3
2
4
S105
1
3
2
4
S109
1
3
2
4
S104
1
3
2
4
S106
1
3
2
4
S112
1
3
2
4
S102,103
S100
1
2
3
4
5
6
7
8S101
28PCN002
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
40PCN001
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
12PCN003
1
2
3
4
5
6
7
8
9
10
11
12
1200R5206
8200R5221
1200R5207
1500R5212
2200R5215
3900R5218
1500R5211
2200R5216
8200R5224
1500R5210
1200R5208
27kR5225
2200R5214
3900R5222
1
A
KEY_AD1
MS_PLAY
MS_-
DISPLAY
VOL_-
MS_INDEX
MS_+
END_SEARCH
VOL_+
MS_DELETE
MEMORY_MIX
KEY_AD2
MENU
AUDIO_DUB
HI_XRESET
DIAL_A
HI_EVER_SO
PANEL_R
DIAL_B
XCS_LCD
VD_SO
PANEL_XVD
KEY_AD1
HI_EVER_SCK
XHD_OUT
XCS_LCD_DRIVER
COM_OUT
LCD_COM/XDATA
VG
EVER_3.0V
VD_SCK
PANEL_G
PANEL_XHD
MAKER_CHECK
HI_XRESET
XCS_LCD
PANEL_G
EVER_3.0V
HI_EVER_SO
VD_SO
PANEL_R
VG
HI_EVER_SCK
XRST_VTR
XHD_OUT
PANEL_XVD
COM_OUT
XCS_LCD_DRIVER
LCD_COM/XDATA
PANEL_XHD
MAKER_CHECK
PANEL_B
KEY_AD4_A
MS_-
MS_+
MEMORY_MIX
MS_DELETE
MS_INDEX
MS_PLAY
KEY_AD1
KEY_AD1
KEY_AD4
KEY_AD2_A
DIAL_A
DIAL_B
XRST_VTR
VD_SCK
KEY_AD3
KEY_AD2_A
AUDIO_DUB
MENU
KEY_AD2
KEY_AD2
VOL_-
DISPLAY
END_SEARCH
VOL_+
KEY_AD3
KEY_AD3
KEY_AD4_A
KEY_AD2
KEY_AD3
KEY_AD4
PANEL_B
DIAL_B
DIAL_A
EXECUTE
GND
GND
XHD_OUT
KEY_AD1
KEY_AD2
BATT_LI_3V
PANEL_R
REG_GND
LCD_COM/XDATA
HI_EVER_SCK
DIAL_A
COM_OUT
PANEL_XHD
XCS_LCD_DRIVER
KEY_AD4
PANEL_B
XRST_VTR
VG
HI_EVER_SO
DIAL_B
MAKER_CHECK
XCS_LCD
EVER_3.0V
PANEL_G
HI_XRESET
VD_SCK
VD_SO
REG_GND
KEY_AD3
PANEL_XVD
BL_REG
BL_CONT
BL_GND
EP_4.75V
EP_2.8V
EP_13.3V
SE_GND
PANEL_-15.3V
MAKER_CHECK
VD_SCK
XRST_VTR
XHD_OUT
PANEL_XHD
HI_EVER_SCK
REG_GND
KEY_AD2_P
HI_EVER_SO
VD_SO
XCS_LCD
EVER_3.0V
PANEL_XVD
PANEL_R
PANEL_G
PANEL_B
LCD_COM/XDATA
PSIG/PANEL_COM
VG
XCS_LCD_DRIVER
SP-
SE_GND
PANEL_-15.3V
BL_GND
PANEL_13.3V
BL_CONT
BL_REG
BL_GND
PANEL_2.8V
BL_REG
PANEL_4.75V
SP+
MS_DELETE
DISPLAY
MS_INDEX
MEMORY_MIX
REG_GND
VOL_-
MS_+
PB_ZOOM
MPEG_PLAY
END_SEARCH
REC
MS_PLAY
MENU
VOL_+
REG_GND
MS_-
AUDIO_DUB
(MPEG_PLAY)
BACK_LIGHT
EXPOSURE
(EXECUTE)
(BACK_LIGHT,EXPOSURE)
(PB_ZOOM)
(REC)
(REC)
(PB_ZOOM)
(MPEG_PLAY)
GND
(BACK_LIGHT,EXPOSURE)
(EXECUTE)
MEMORY/PLAY
MPEGDISPLAY
ENDSEARCH
DUBBING
MEMORY -
VOLUME +INDEXMEMORY +
MEMORYMIX
MEMORY DELETE
VOLUME -
MENU PB ZOOM
EXECUTE
DIAL_B
GND
GND
EXEC
DIAL_A
BACK_LIGHT
GND
GND
EXPOSURE
OSD_SO
BL_REG
MAKER_CHECK
COM_OUT
SP+
XOSD_SCK
PANEL_R
KEY_AD2
HI_XRESET
XHD_OUT
SE_GND
PANEL_G
BATT_LI_3V
PANEL_XVD
REG_GND
BL_GND
HI_XRESET
VD_SCK
DIAL_A
KEY_AD4
XRST_VTR
REG_GND
PANEL_4.75V
BL_GND
VD_SO
DIAL_B
EVER_3.0V
PANEL_XHD
XCS_LCD
DIAL_B
LCD_COM/XDATA
PANEL_-15.3V
BL_REG
BL_CONT
PANEL_B
VG
BATT_LI_3V
KEY_AD3
PANEL_13.3V
DIAL_A
PANEL_2.8V
XCS_LCD_DRIVER
SP-
KEY_AD1
REC
XHD_OUT
HI_EVER_SCK
PANEL_R
SP+
PANEL_-15.3V
MAKER_CHECK
XRST_VTR
PANEL_XVD
PANEL_2.8V
PANEL_XHD
PANEL_4.75V
LCD_COM/XDATA
SE_GND
PANEL_G
BL_CONT
KEY_AD3
PANEL_B
BL_GND
COM_OUT
BL_REG
SP-
PANEL_13.3V
KEY_AD2
EVER_3.0V
BL_REG
KEY_AD4
HI_EVER_SO
VD_SO
BL_GND
KEY_AD1
VD_SCK
REG_GND
XCS_LCD
REG_GND
VG
XCS_LCD_DRIVER
(LITHIUM BATTERY) (STOP) (REW) (PLAY) (FF) (PAUSE)
RESET
S103
BACKLIGHT EXPOSURE
SEL/PUSH EXEC
S102
(PANEL OPEN/CLOSE)
TOPD-161 BOARD(1/2)CN5652
(PAGE 4-19)
TOPD-161 BOARD(1/2)CN5651
(PAGE 4-19)
CONTROL SWITCH BLOCK(KP-CX2670)
SP901SPEAKER
TOVC-280 BOARD(15/15)CN1005
(PAGE 4-66)
TOVA-117 BOARD(2/6)CN4004
(PAGE 4-25)
FP-434 FLEXIBLE
CONTROL SWITCH BLOCK(SH-CX2670)
CK-108 BOARDSWITCH,CONNECTORXX MARK:NO MOUNT
REC
SIGNALCHROMA
VIDEO SIGNAL
PB
SIGNAL PATH
Y Y/CHROMAAUDIO
H
2 3 12
J
179
G
11
E
C
10
K
14136
B
7
I
D
18
F
155
L
84 16
16
CONTROL SWITCH BLOCK(SH-CX2670)is replaced as a block.So that this PRINTED WIRING BOARD is omitted.
CONTROL SWITCH BLOCK(KP-CX2670)is replaced as a block.So that this PRINTED WIRING BOARD is omitted.
REC
THROUGHTHE PV-138 HARNESS
THROUGHTHE PV-138 HARNESS
• AbbreviationEE : East European modelNE : North European modelHK : Hong Kong model
AUS : Australian modelCH : Chinese modelJE : Tourist model
DCR-TRV16/TRV16E/TRV18/TRV18E/TRV116E/TRV118E
COVERCOVER
4-17 CONTROL SWITCH BLOCK (PS-CX2670)4-18
4-2. SCHEMATIC DIAGRAMS 4-3. PRINTED WIRING BOARDS4-2. SCHEMATIC DIAGRAMS 4-3. PRINTED WIRING BOARDS
(DCR-TRV18/ TRV18E/ TRV118E)
(DCR-TRV16/TRV16E:E,HK,AUS,CH/TRV18/TRV18E:E,HK,AUS,CH,JE/TRV116E/TRV118E)
(DCR-TRV16E:AEP,UK,EE,NE/ TRV18E:AEP,UK,EE,NE)
(DCR-TRV18/TRV18E/TRV118E)
S071 RV001
S1
S2
SML-310LTT86D001
8PCN001
1
2
3
4
5
6
7
8
1
2
3
4
5
6
7
8
10PCN001
1
2
3
4
5
6
7
8
9
10
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
1
A
GND
MS_DIO
D_2.8V
MS_VCC
GND
ZOOM_AD
KEY_AD_0
MS_INSERT
MS_BS
MS_SCLK
GND
GND
XPHOTO_FREEZE
MS_VCC
ACCESS_LED
XS/S_SW
XVTR_MODE_SW
XCAM_STBY_SW
XPHOTO_STBY_SW
D_2.8V
GND
MS_BS
MS_VCC
MS_SCLK
MS_INSERT
GND
MS_VCC
MS_DIO
GND
MS_VCC
MS_INSERT
GND
MS_INSERT
MS_BS
MS_VCC
MS_DIO
GND
MS_SCLK
MS_DIO
MS_BS
MS_VCC
N.C.
MS_VCC
GND
N.C.MS_SCLK
TOVC-280 BOARD(15/15)CN1008
(PAGE 4-66)
PHOT0 T W
(ZOOM)
POWER
MEMORY
CAMERA
OFF(CHG)
VCR
START/STOP
CONTROL SWITCH BLOCK(PS-CX2670)
FP-438 FLEXIBLE
MEMORY STICKCONNECTOR
2 3 9
E
C
6
B
7
D
5 84
16
(ACCESS)
PLAYER
• AbbreviationEE : East European modelNE : North European modelHK : Hong Kong model
AUS : Australian modelCH : Chinese modelJE : Tourist model
DCR-TRV16/TRV16E/TRV18/TRV18E/TRV116E/TRV118E
COVERCOVER
4-19 4-20PD-161 (1/2)
4-2. SCHEMATIC DIAGRAMS PD-161 PRINTED WIRING BOARD4-2. SCHEMATIC DIAGRAMS PD-161 PRINTED WIRING BOARD
For Schematic Diagram• Refer to page 4-73 for printed wiring board.• Refer to page 4-89 for waveforms.
13.813.2
4.1 13.8
4.7 13.2
-15.9
3.4
2.8
-15.2 -15.9
-15.2
4.7 4.7
0
0
2.8
R0.
7/p0
1.7
R1.
1/p0
2.7
0.2
1.4
1.4
6.9
13.8
4.7
1.6
2.8
2.6
2.7
2.7
2.8
2.8
1.1
2.8
1.8
1.8
1.8
1.7
1.7
1.7
4.7
2.3
2.3
2.3
13.8
1.4
R3.
1P
2.8
1.4
1.4
1.4
4
5
6
2
3
1
0.2
1.4
1.4
2.6
2.8
2.6
2.8
2.7
2.7
R2.7P2.0
2.7
2.8
2.8
1.4
2.8
1.4
1.4
2.8
P0.1R1.4
R1.4P1.3
R0.4P1.4
R2.4P2.8
R0.1P2.3
R2.8P1.4
R0P2.8
R0P2.8
R0P2.8
R0.1P2.8
R2.3P0
P2.8R0.5
2.6
2.6
2.8
2.8 0
R2.
8P
2.4
8
7
9
NO MARK:REC/PB MODE R :REC MODE P :PB MODE
0.01uC5507
XXC5523
0.1u BC5517
1u BC5524
0.01uC5506
560p
CH
C55
11
XXR5518
0.1uB
C5512
24PCN5501
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
R552147k
0R5523
IC5502LZ9FF474
1
HD
I
2
HD
B
3
W/H
4
BL-
ON
5
BL-
DET
6
GN
D/T
ESTI
7
TES
TI/G
ND
8
LED
9
PW
M
10
TES
TI
11
TES
TI
12
CP
MO
DE/
CLS
13CP/SPS
14GRES/EX1
15GPCK/MODE1
16GSRT/MODE2
17STBYB/PSG
18RESET/EX2
21OE/PSS2
19VDD/RES
20SRT/PSS1
22CLR/CTR
23MCLK/CLD
24HCNT/SPD
25D
R.P
.SA
VE
26
OS
CO
27
OS
CI
28
XC
.SA
VE
29
PD
30
PS
/VD
D
31
GN
D
32
-IN
/TES
TO
33
+IN
/TES
TO
34
OU
T/TE
STO
35
SY
F
36
PO
CB
37 BGP
38 SWCOM
39 SW
40 FRP
41 COM_FRP
42 XSCK
45 SO
44 XCS
43 VDD/TESTI
46 SI
47 VSYB
48 XVD
0.01uC5505
10uC5514
TA6.3V
AA
XXR5520
1MR5513
D55021SV290(TPL3)
XXR5514
22kR5509
DETIN
XXR5528
FB55010uH
± 0.5%68k
R5503
FB5502 0uH
LED
MA111-(K8).S0D5503
68kR5510
L5502 XX
Q5503HN1B04FE-Y/GR(TPLR3)
3
5
46
2
1
1uB
C5521
Q5504HN1B04FE-Y/GR(TPLR3)
3
5
4 6
2
1
RN1104F(TPL3)Q5505
BL_ON
0.01uB
C5527
0.001uB
C5515
XXR5525
1MR5533
L550110uH
1kR5534
MGSF1P02LT1Q5502
100kR5532
XXC5503
180kR5531
0.01uB
C5530
C5532XX
470kR5501
XXR5529
0.1u BC5518
XXR5530
0.01uB
C5531
15kR5505
L55036.8uH
0.01uB
C5510
XXC5522
0.1u BC5519
0.01uB
C5504
C5509
20V1u
0.01uB
C5513
0R5515
47kR5507
IC5501CXA3592R-T4
1
N.C
.
2
N.C
.
3N
.C.
4
N.C
.
5
N.C
.
6
N.C
.
7
BIA
S
8
OP
_IN
+
9
OP
_IN
-
10
OP
_OU
T
11
VC
O
12
N.C
.
13N.C.
14N.C.
15Vcc4
16VSH
17GND1
18GND2
21G_DC_DET
19R_DC_DET
20VR
22VG
23B_DC_DET
24VB
25
Vcc
2
26
Vcc
3
27
CO
M_O
UT
28
N.C
29
CO
M_F
RP
30
FRP
31
GN
D3
32
BLA
CK
_IN
33
BG
P
34
N.C
.
35
EXT_
DA
1
36
R_I
NJE
CT
37 EXT_DA2
38 XC.SAVE
39 XSCK
40 SI
41 XCS
42 Vcc1
45 XP.SAVE
44 LPF_ADJ
43 TRAP_ADJ
46 B_IN47 G_IN
48 R_IN
XXR5517
100kR5512
R55190
XXR5502
DAC
68kR5508
2700R5506
1MR5511
68pCH
C5516
10kR5516
RB5501100
FB5503 0uH
RB55021M
RB550310k
D5504XX
16V6.8u
C5520
TA
C5528
AA20V1u
C55080.1u
R55522.2k
1kR5591
C5501
6.3V10u
100kR5540
100kR5541
HI_EVER_SCK
BL_GND
XCS_LCD_DRIVER
6PCN5653
1
2
3
4
5
6
BL_CONT
LCD_COM/XDATA
BL_REG
8PCN5651
1
2
3
4
5
6
7
8
EP_4.75V
EVER_3.0V
SE_GND
CN5652 20P
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
HI_EVER_SO
EP_2.8V
REG_GND
S001
1
A
TG14
TG16
TG15
TG13
XCS_LCD VR
VB
VD_SCK
TG18
TG16
TG15
TG14
TG13
CO
M_F
RP
FRP
BG
P
XP.SAVE
BGP
VD_SCK
XCS_LCD
VD_SO
PANEL_XHD
XHD_OUT
FRP
BLK
XP.
SA
VE
XC.SAVE
XTG_SO
TG18
TG20
TG21
TG22
TG24
COM_FRP
XTG_SO
TG24
BLK
VB
VG
TG23
TG22
TG20
TG21
TG19
TG17
TG17
TG12
TG12
TG19
XC
.SA
VE
TG23
PANEL_XVD
VG
VR
VD_SCK
XCS_LCD
VD_SO
PANEL_XVD
PANEL_XHD
XHD_OUT
CLS
VGLAC
CLD
PSS1
PSS2
EX1
MO2
RES
EX2
VB
VG
VR
VGL
SPS
VSH5V
MO1
GND
VSH3V
GND
VCOM
CTR
VGH
PSG
SPD
IC5501RGB DRIVE
TIMING GENERATOR
IC5502PANEL_REV
GND
PANEL_REV
PANEL_XVD
PSIG/PANEL_COM
EP_2.8V
BL_REG
PANEL_R
XCS_LCD_DRIVER
GND
VD_SO
MAKER_CHECK
BL_GND
PANEL_XHD
VG
PANEL_G
EP_4.75V
XRST_VTR
XCS_LCD
LCD_COM/XDATA
GND
REG_GND
EP_13.3V
BL_CONT
KEY_AD2_P
EVER_3.0V
SE_GND
N.C.
XHD_OUT
VD_SCK
PANEL_-15.3V
PANEL_B
HI_EVER_SO
HI_EVER_SCK
LCD9012.5INCHCOLORLCD UNIT
SWITCH
SWITCHSWITCH
B+ SWITCH
TOCK-108 BOARDCN5204
THROUGHTHE PV-138 HARNESS
(PAGE 4-16)
(PAGE 4-16)
THROUGHTHE PV-138 HARNESS
TOCK-108 BOARDCN5203
FP-309FLEXIBLE
(PANEL REVERSE)
H
2 3 12
J
179
G
11
E
C
10
K
14136
B
7
I
D
18
F
155
L
84 16
XX MARK:NO MOUNT
RGB DRIVE,TIMING GENERATORPD-161 BOARD(1/2)
REC
SIGNAL PATH
PB
CHROMA Y/CHROMA
VIDEO SIGNAL
Y
163 (2/2)
(2/2)2
1 (2/2)
DCR-TRV16/TRV16E/TRV18/TRV18E/TRV116E/TRV118E
COVERCOVER
4-21 4-22 PD-161 (2/2)
4-2. SCHEMATIC DIAGRAMS PD-161 PRINTED WIRING BOARD4-2. SCHEMATIC DIAGRAMS PD-161 PRINTED WIRING BOARD
For Schematic Diagram• Refer to page 4-73 for printed wiring board.• Refer to page 4-89 for waveform.
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.6
2.0
3.0
3.0
3.0
3.0
0
3.0 0
1.5
1.5
1.5
1.5
1.5
1.5
10
NO MARK:REC/PB MODE
1.8
0
2.8
1.7
2.8
0
2.8
2.8 0.3
2.8 1.5
4.7 0.3
0
4.7
4.7
4.84.8
-0.7 -0.7
LED
D56
02P
G11
12H
-TR
R5609 XX
BL_REG
MA111-(K8).S0D5601
EP_2.8V
L56010uH
IC5601TC7W53FU(TE12R)
1 COM
2 INH
3 VEE
4 GND 5A
6CH1
7CH0
8VCC
EP_4.75V
R560322k
0.015uB
C5603
1/10W1800R5601
XXR5604
IC5602TA75S393F-TE85R
12
345
R5605120
BL_GND
0.1uB
C5605
DETIN
DAC
R5608 XX
10PCN5601
1 LED_GND
2 LED
3 BL_LOW
4 N.C.
5 N.C.
6 N.C.
7 N.C.
8 N.C.
9 N.C.
10 BL_HIGH
D5604 XX
B
C56040.1u
BL_ON
R5602180k
BL_CONT
XXD5603LD5605
A
C560612p3kVSL
470R5607
22kR5606
Q5603RN4983FE(TPLR3)
3
5
4
6
2
1
T5601
1
2
3
4
5
6
10
4.7uB
C5607
10kR5613
R5614 XX
RN1104F(TPL3)Q5601
10kR5612
XXQ5604
Q5605CPH5504-TL-E
5
1
2
4
3
XCS_LCD_DRIVER
HI_EVER_SCK
HI_EVER_SO
LCD_COM/XDATA
20PCN5654
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
XXIC5651
1 OSC1
2 OSC2
3 VSS
4 VC
5 VLCD
6 VDD
7 SCK
8 SO
9
XC
S
10
C/X
D
11
CO
M1
12
CO
M2
13
CO
M3
14
CO
M4
15
SEG
1
16
SEG
2
17SEG3
18SEG4
19SEG5
20SEG6
21SEG7
22SEG8
23SEG9
24SEG10
25
SEG
11
26
SEG
12
27
SEG
13
28
SEG
14
29
SEG
15
30
SEG
16
31
SEG
17
32
SEG
18
REG_GND
680kR5652
270R5651
EVER_3.0V
VD5651
ND901
1
A
SE_GND
SEG10
SEG
15
SEG9
SEG12
SEG4
SEG4
SEG
1
SEG
11
CO
M3
COM2
CO
M2
COM3
SEG1
SEG15
SEG7
SEG10 SEG3
SEG14
SEG5
SEG3
SEG11
SEG16
SEG
14
SEG13
SEG
13
SEG6
CO
M1
COM4
COM1
SEG5
SEG
12
SEG6
SEG
16
CO
M4
SEG7
SEG
2
SEG8
SEG2
SEG9
SEG8
VCC
SELECT SWITCH
IC5601
IC5602CURRENT DETECT
COM2
SEG1
SEG13
SEG3
SEG9
COM4
SEG5
SEG16
COM1
LCD DRIVE
SEG2
SEG6IC5651
SEG7
SEG14
SEG12
SEG11
COM3
SEG4
SEG15
SEG8
SEG10
LCD902CHARACTER DISPLAY
FP-441FLEXIBLE
BACKLIGHT
SWITCHING
LED DRIVE
INV
2
G
5
E
3
F
4
C
9
D
I
B
8 11
H
76 10
XX MARK:NO MOUNT
PD-161 BOARD(2/2)LCD DRIVE,BACKLIGHT
16
2 (1/2)
1 (1/2)
3 (1/2)
INVERTER TRANSFORMER
(STA
RTE
R)
Note :The components identified bymark 0 or dotted line with mark0 are critical for safety.Replace only with part numberspecified.
Note :Les composants identifiés parune marque 0 sont critiquespour la sécurité.Ne les remplacer que par unepièce portant le numéro spécifié.
DCR-TRV16/TRV16E/TRV18/TRV18E/TRV116E/TRV118E
COVERCOVER
4-23 4-24VA-117 (1/6)
4-2. SCHEMATIC DIAGRAMS VA-117 BOARD SIDE A VA-117 BOARD SIDE B4-2. SCHEMATIC DIAGRAMS VA-117 BOARD SIDE A VA-117 BOARD SIDE B
For Schematic Diagram• Refer to page 4-81 for printed wiring board.• Refer to page 4-90, 4-91 for waveforms.
0
2.8
2.6
2.2
2.6
2.8
2.8
1.3
2.8
1.7
1.7
1.7
0 2.0
13.7
2.7
0 1.4
6.7
3.0
6.7
3.0
6.7
3.1
13.7
6.4
6.4
2.8
0.9
2.8
0.9
0.9
1.4
1.4
1.4
1.4
2.9
16
15
14
13
12
11
2.7
0
1.4
2.6
2.8
2.6
2.3
2.5
2.7
2.6
0.9
2.8
0.9
0.9
1.4
2.8
1.4
1.4
2.8
0
1.4
1.4
0.1
2.8
2.7
2.8
1.4
0
2.5
0.3
2.8
2.8
18
19
17
NO MARK:REC/PB MODE
6.8uHL4202
100R4212
2700
R42
05
B0.01uC4205
2.2uB
C4218
100R4214
0.01uB
C4208
FB42010uH
C42171u
68kR4209
B0.01uC4204
0.1uB
C4210
1MR4210
PANEL_XHD
68kR4207
VD_SCK
R4204XX
100kR4211
PANEL_XVD
VD_SO
47kR4206
C4203XX
XCS_EVF
560pCH
C4209
L420110uH
22kR4208
100R4213
C42161u
1SV290(TPL3)D4201
4.7u20V
C4211
0R4203
EP_13.3V
120pCH
C4214
REG_GND
0.01u
B
C4213
16V
XXC4202
VCO
470kR4201
± 0.5%100k
R4202
0.001uB
C4212
XXC4223
C42151u
G
B0.01uC4206
EP_2.8V
XRST_VTR
0R4221
0R4222
EP_4.75V
20PCN4201
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
FB42020uH
R4215XX
R4220XX
R4219XX
R4218XX
2.2uF
C4219
± 0.5%
R421647k
± 0.5%1M
R4217
C4207XX
C42014.7u
CL4201
0R4223
1
A
EVF_G/BW_Y
EVF_R
EVF_B
CXA3289AR-T4IC4201
1
XS
H.S
AV
E
2
SH
_R
3
SH
_G
4
SH
_B
5
SH
_A
6
N.C
.
7
BIA
S
8
OP
_IN
+
9
OP
_IN
-
10
OP
_OU
T
11
VC
O
12
CO
M_D
C
13COM_IN
14COM_OUT
15Vcc3
16VREF
17GND1
18GND2
21G_DC_DET
19R_DC_DET
20VR
22VG
23B_DC_DET
24VB
25
Vcc
2
26
P_D
C_D
ET
27
VP
28
XV
P.S
AV
E
29
PFR
P
30
FRP
31
PR
G
32
BLA
CK
_IN
33
BG
P
34
N.C
.
35
EXT_
DA
36
R_I
NJE
CT
37 N.C.
38 XC.SAVE
39 XSCK
40 SI
41 XCS
42 Vcc1
45 XP.SAVE
44 LPF_ADJ
43 TRAP_ADJ
46 B_IN
47 G_IN
48 R_IN
CXD3501AR-T4IC4202
1
HD
2
HD
O
3
XW
RT
4
CM
PO
5
DET
IN
6
GN
D
7
TES
TI
8
LED
9
PW
M
10
-IN
11
+IN
12
TES
T
13N.C.
14VST
15VCK
16STB
17EN
18DCG/CLR
21HST
19VDD
20RGT
22HCK2
23HCK1
24BLK
25
XS
TBY
26
OS
CO
27
OS
CI
28
XC
SA
VE
29
RP
D
30
TES
T
31
GN
D
32
SH
A
33
SH
B
34
SH
G
35
SH
R
36
XC
LR
37 XCLP
38 TEST
39 SBLK
40 FRP
41 TEST
42 XSCK
45 SO
44 XCS
43 VDD
46 SI
47 VDO
48 XVDR4224 1k PANEL_XVD
BGP
XP_SAVE
XC_SAVE
BG
P
SB
LK
FRP
XCS_EVF
TG24
TG21
SH
R
SH
G
SH
B
SH
A
SH
A
SH
B
SH
G
SH
R
PANEL_XHD
XP
_SA
VE
XC
_SA
VE
SBLK
FRP
TG15
TG14
TG16
TG17
VCO
VD_SO
VD_SCK_EVF
XCS_EVF
XTG_SO
EVF_B
VCO
PANEL_XHD
XCS_EVF
VD_SO
VD_SCK_EVF
TG23
TG22
EVF_G/BW_Y
EVF_R
TG24
TG21
TG22
TG23
TG17
TG16
TG15
G
XRST_VTR
TG14
VD_SCK_EVF
XTG_SO
XRST_VTR
EVF_R
EVF_G/BW_Y
EVF_B
G
PANEL_XVD
EVF_GND
VCK
HST
EN
VR
COM
HCK1
XTALLY_LED
W_LED_4.75V
HCK2
VG
LED_ON/OFF
VB
LED_DA
BLK
VST
EVF_VDD
STB
EVF_GND
EVF_GND
TA A
RGB DRIVE
IC4201
IC4202TIMING GENERATOR
TOLB-077 BOARDCN6101
THROUGH THEFP-435 FLEXIBLE( )
(PAGE 4-10)
RGB DRIVE,TG(VF BLOCK)XX MARK:NO MOUNT
VA-117 BOARD(1/6)
9
G
K
E
8 15
F
5
J
C
143 7 114 13
I
2
B
6 10 12
L
D
H
16
VIDEO SIGNAL
REC
Y
PB
CHROMA
SIGNAL PATH
Y/CHROMA
(4/6)1
(6/6)2
DCR-TRV16/TRV16E/TRV18/TRV18E/TRV116E/TRV118E
COVERCOVER
4-25 4-26 VA-117 (2/6)
4-2. SCHEMATIC DIAGRAMS VA-117 BOARD SIDE A VA-117 BOARD SIDE B4-2. SCHEMATIC DIAGRAMS VA-117 BOARD SIDE A VA-117 BOARD SIDE B
For Schematic Diagram• Refer to page 4-81 for printed wiring board.
2.8
2.3
R
1.6
1.4
1.4
1.6
2.8
1.6
1.6
R1.8P0
R1.9P0.4
0.1
2.5
2.7
2.8
2.4
1.6
1.6
3.3
1.8
1.6
1.8
1.8
R1.9/P0
R1.0/P0.3
4.7
2.4
2.4
0
0
2.4
2.4
0
4.7
R1.9P0.5
R1.9P0
R1.9P0.5
0 0
-0.4-0.40
0.1
2.7
2.42.4
0.1 0.1
2.4 2.4
0 0
-0.5-0.5
3.3 8.2
4.2
NO MARK:REC/PB MODE R :REC MODE P :PB MODE
XCS_AU1
AU_4.75V
AU_LINE_I/O_L
AU_2.8V
0.01uB
C4314
10u6.3V
ATA
C4305
4V47u
C4324
4V47u
C4323
AU_LINE_I/O_R
TA
10u
A6.3V
C4318
220kR4302 10u
6.3VATA
C4328
3900R4303
10u6.3V
ATA
C4327
33kR4301
TA
10u
A6.3V
C4311
15u4V
C4316
A
B0.1u
C4310
10uA6.3V
C4322
VTR_UNREG
B1uC4307
0.01uB
C4312
B1u
C4306
B0.1u
C4309
B1u
C4317
XAUDIO_IN
BEEP_IN
B1u
C4315
VSP_SO
1uB
C4325
XVSP_SCK
1u BC4326
2SD1834-T100Q4301
1uB
C4308
1uB
C4302
L430110uH
B1u
C4304
B1uC4303
FB43010uH
A4V
TA
4.7uC4319
RN2111F(TPL3)Q4306
RN1104F(TPL3)Q4304
XXC4313
MIC_R
MIC_L
RN2910FE(TPLR3)Q4303
6
2
1
3
5
4
0.22u BC4321
10uA6.3V
C4320RN1910FE(TPLR3)
Q4307
3
5
4
6
2
1
RN1910FE(TPLR3)Q4305
6
2
1
3
5
4XX
Q4302
47kR4308
47kR4309
2200R4307
2200R4306
1kR4311
1kR4310
10kR4304
10kR4305
REG_GND
LA74207W-TBM-EIC4301
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
1718
1920
2122
2324
2526
2728
2930
3132
33343536373839404142434445464748
4950
5152
5354
5556
5758
5960
6162
6364
REC_OUT_L
REC_OUT_R
PB_IN_L
PB_IN_R
C4301XX
IC4301_L
IC4301_R
HP_L_OUT
HP_R_OUT
47R
4316
47R
4318
47R
4319
47R43
17
PANEL_-15.3V
BL_REG
REG_GND(BL_GND)
EP_13.3V
EP_2.8V
12PCN4004
1
2
3
4
5
6
7
8
9
10
11
12
BL_CONT
EP_4.75V
REG_GND
REG_GND
1
A
XC
S_A
U1
XV
SP
_SC
K
VS
P_S
O
PANEL_-15.3V
EP_2.8V
EP_4.75V
EP_13.3V
BL_REG
VSP_SO
XVSP_SCK
XCS_AU1
BL_REG
PANEL_-15.3V
EP_13.3V
EP_4.75V
EP_2.8V
LINE2_OUT(R)
LPF_IN(L)
Vcc(M)
LINE1_OUT(R)
ALC_OUT(L)
MU
TE
MIC
_CTL
2(R
)
INT_
MIC
_Vcc
LPF_IN(R)
HP_OUT(L)
XC
S_A
U
MIC
_EX
T/IN
T
ALC_OUT(R)
Vcc
(D)
VS
P_S
O
VR
EFS
XV
SP
_SC
K
EXT_
MIC
(L)
LINE1_IN(L)
MIC
_OU
T(L)
AGC_TC
D_G
ND
XMIC_P_SAVE
MIC_IN(R)
Vcc(H)
MIC
_IN
(L)
LINE2_IN(R)
REC_OUT(L)
MIC
_GN
D
Vcc(L)
VREFM
INT_
MIC
(R)
MIC
_OU
T(R
)
EXT_
MIC
_Vcc
SP
_Vcc
VREFH
PB_IN(R)
EXT_MIC(R)
SP
_OU
T-
HP
_OU
T(R
)
INT_
MIC
(L)
MIX
_OU
TM
IC_M
ON
O
SP
_GN
D
LINE2_OUT(L)
BEE
P_I
N
MIC
_CTL
2(L)
HP
_CO
M
SP
_IN
MIC_DET1
LINE1_IN(R)
POWER_MUTE
LINE1_OUT(L)
PB_IN(L)
SP
OU
T+
MIC
_DET
2
P.MUTE_TC
LINE2_IN(L)REC_OUT(R)
MIC
_CTL
1(L)
A_GNDA_GND
MIC
_CTL
1(R
)
A_GND
BL_CONT
BL_GND
SP-
PANEL_2.8V
PANEL_-15.3V
PANEL_4.75V
BL_GND
SE_GND
PANEL_13.3V
SP+
BL_REG
BL_REG
TOFP-434 FLEXIBLECN003
(PAGE 4-15)
REC
PB
AUDIO
SIGNAL PATH
SIGNAL
16
9
G
E
8
F
5
C
143 7 114 132
B
6 10 12
D
H
AUDIO(AU BLOCK)VA-117 BOARD(2/6)
XX MARK:NO MOUNT
IC4301AUDIO IN/OUT
MUTE
MUTING
AUDIO I/O SWITCH
SWITCH
3 (6/6)
9 (4/6)
4 (4/6)
5 (3/6)
(6/6)6
7 (3/6)
8 (4/6)
DCR-TRV16/TRV16E/TRV18/TRV18E/TRV116E/TRV118E
COVERCOVER
4-27 4-28VA-117 (3/6)
4-2. SCHEMATIC DIAGRAMS VA-117 BOARD SIDE A VA-117 BOARD SIDE B4-2. SCHEMATIC DIAGRAMS VA-117 BOARD SIDE A VA-117 BOARD SIDE B
For Schematic Diagram• Refer to page 4-81 for printed wiring board.
1.0
0.1
0.1
0.1
2.8
1.4
2.9
2.6
2.0
2.8
0.2
2.5
1.4
2.8
R3.0P0
1.4
1.4
2.5
1.4
2.2
1.4
1.4
1.4
1.4
1.4
1.4
1.2
1.4
1.4
1.4
0
1.4
1.4
1.4
1.4
1.4
1.4
2.5
2.2
1.4
1.4
1.4
1.4
1.4
1.4
1.4
NO MARK:REC/PB MODE R :REC MODE P :PB MODE
12kR4424
B6800pC4404
1kR
4410
47kR4419
10kR4403
22kR4415
4700R4404
BH7870AKV-E2IC4401
1 2 3 4 5 6 7 8 9 10 11 12
1314
1516
1718
1920
2122
2324
252627282930313233343536
3738
3940
4142
4344
4546
4748
XXC4418
XXR4416
B0.01uC4430 B
6800pC4429
B0.1u
C4419
XXC4415
B0.001uC4414
B6800pC4402
22kR4417
2200R4406
2200R4401
2700R4402
XXC4431
XXR4414 B6800p
C4428
B0.01uC4426
1kR
4411
CH100p
C4412
XXC4424
XXR4413
B0.1u
C4421
B0.022uC4401
100kR4425
CH100pC4417
2200R4407
CH100p
C4413
A6.3V10u
C4406
CH100p
C4416
B0.01uC4425
A6.3V10u
C4411
12kR4420
0.01uB
C4405
B0.022uC4403
MIC_R
REG_GND
100uHL4401
1uB
C4434
MIC_L
6800R4408
B0.1uC4420
TA
22u4V
A
C4432
XMIC_MONO
47kR4418
XXC4422
EXT_MIC_JACK
B0.01uC4427
XXC4407
ZOOM_MIC_CONT
B0.001uC4410
XXC4409
XX
*C4408
12kR4421
0R4405
6800R4409
0R4422
0.01uB
C4433
10kR4423
B0.047uC4435
B0.1uC4423
B0.047uC4437
3300R4427 XX
C4436
XXR4428
XXC4438
XXR4429
XXR4426
XXR4412
SHOE_MIC_L
XXR4431
AU_4.75V
AU_2.8V
0R4430
XXD4401
HP_R_OUT
XF_TALLY_LED
HP_L_OUT
24PCN4003
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
MF_LED
MF_B
HP_JACK_IN
SIRCS_SIG
MF_A
A_4.75V
KEY_AD6
IR_ON
3300R4010
47R4011
MT_5V
0R4013
2SC5585H-T2LQ4003
RN1111F(TPL3)Q4001
47R4012
SIRCS_PWM
68R4009
REG_GND
REG_GND
1
A
HP_JACK_IN
HP_R_OUT
HP_L_OUT
XF_TALLY_LED
MF_LED
MF_B
SIRCS_SIG
MF_A
KEY_AD6
IR_ON
SIRCS_PWM
HP_R_OUT
HP_L_OUT
HP_JACK_IN
SIRCS_SIG
MF_LED
XF_TALLY_LED
MF_B
MF_A
KEY_AD6
SIRCS_PWM
IR_ON
N.C.
INV
T_O
UT_
L
EXT_
IN_R
N.C.
SU
B_S
IG_O
UT_
L
MO
DE_
CTL
_1
C_REG
AM
P_O
UT_
R
C_1/2VCC
SG
_IN
_R
INV
T_O
UT_
R
HP
F_O
UT_
L
SU
B_S
IG_O
UT_
R
HPF_AMP_IN_L
MTX
_AM
P_I
N_R
INT_
IN_L
MTX
_AM
P_O
UT_
R
SU
B_I
N_L
HP
F_O
UT_
R
GND
HP
F_A
MP
_IN
_R
ZOOM_AMP_OUT
HPF_ON/OFF
R_OUT
ZOOM_AMP_IN
REG
_2.5
V
MIC_MONO
MIX_OUT
EXT_
IN_L
L_OUT
GND
MO
DE_
CTL
_2
ZOOM_BAL
INT_
IN_R
SG
_IN
_L
ZOOM_POSI
SUB_IN_R
MTX
_AM
P_O
UT_
L
VCC
N.C.
AM
P_O
UT_
L
EXT_MIC
N.C.
MTX
_AM
P_I
N_L
REG
_2.5
V
REG_GND
HP_JACK_IN
EXT_MIC_R
MF_B
KEY_AD6
MIC_GND
N.C. (MF_LED)
NS_LED_K
A_4.6V
INT_MIC_R
REG_GND
REG_GND
EXT_MIC_L
MIC_GND
NS_LED_A
INT_MIC_L
SIRCS_SIG
MIC_GND
XF_TALLY_LED
HP_R_OUT
HP_L_OUT
MF_A
MIC_GND
AU_2.8V
TOMA-409 BOARDCN5902
)(PAGE 4-12)
( THROUGHTHE FP-437 FLEXIBLE
LED DRIVE
SWITCH
MIC AMP
IC4401
MIC AMP(MA BLOCK)VA-117 BOARD(3/6)
XX MARK:NO MOUNT
9
G
E
8
F
5
C
3 7 114 132
B
6 10 12
D
16
PB
REC
SIGNAL PATH
SIGNALAUDIO
10 (4/6)
(2/6)7
11 (4/6)
(6/6)12
5 (2/6)
13 (6/6)
DCR-TRV16/TRV16E/TRV18/TRV18E/TRV116E/TRV118E
COVERCOVER
4-29 4-30
4-2. SCHEMATIC DIAGRAMS VA-117 BOARD SIDE A VA-117 BOARD SIDE B4-2. SCHEMATIC DIAGRAMS VA-117 BOARD SIDE A VA-117 BOARD SIDE B
VA-117 (4/6)
For Schematic Diagram• Refer to page 4-81 for printed wiring board.• Refer to page 4-91 for waveforms.
0.8
1.6
1.5
0.8
0.8
1.3
0
1.5
2.1
1.5
8.2
3.0
3.0
1.6
0.9
0.9
0.9
2.6
0.7
0.3
0.3
0.6
1.1
1.2
1.2
4.9
8.2
8.1
6.4
7.7
8.2
8.1
7.1
8.6
8.5
7.0
8.0
8.0
7.0
8.5
2.9
8.0
8.2
R8.4P8.6R6.8P7.1
1.5
15.7 1.1
1.5
4.7
0.9
1.5
2.9
1.5
2.3
8.4
6.8
7.9
7.7
6.5
8.1
20
21
8.2 5.1
R7.6P7.8
R7.2/P8.0
R3.1P3.4
5.1
2.8
2.3
4.98.2
7.7
0.98.2
8.1
8.0
8.2 2.6
1.68.2
8.0
2.9
2.3
8.2
7.9
2.9
8.2
0 0
8.0 0 0
7.7
8.2 4.7
R-1.4P-1.6
1.5
15.7 R15.2/P0
R15.0P15.8
P0
R15
.2
R4.
6/P
0
4.7
P5.2R4.2
R2.3P0
R2.8P0
R-9.9/P-10.1 R-7.6P0
R-9.5P-10.2
P0
R-7
.6
R-0
.9/P
0.2
P-0.2R0.4
13.9
15.7
14.5
R-25.3/P-23.3
R-25.2/P23.5
-1.1
-15.9
0.4
1.9
2.82.8
1.2
NO MARK:REC/PB MODE R :REC MODE P :PB MODE
L450622uH
± 0.5%47k
R4551
2SC4738F-Y/GR(TPL3)Q4514
CXA3282R-T6
IC4501
12345678910111213141516
1718
1920
2122
2324
2526
2728
2930
3132
33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48
4950
5152
5354
5556
5758
5960
6162
6364
L45194.7uH
A_2.8V
±0.
5%18
kR45
15
C45284.7u10V B
2SC4738F-Y/GR(TPL3)Q4519
47kR4524
10kR4507
D_1.9V
22kR4533
REG_1.5V
4700pB
C4508
2SC4738F-Y/GR(TPL3)Q4521
4700
pB
C45
10
10u6.3V
A
C4533
CPH6702-TL-EQ4508
1
2
3 4
5
6
C45304.7u10V B
REG_GND
L45104.7uH
L450422uH
AU_4.75V
100kR4537
DRUM_ERROR
± 0.5%
R4504470k
BL_CONT
22k
R45
19
680pB
C4509
± 5%4700
R4544
± 0.5%15k
R4552
REG_GND
4700
R45
12
CAM_DD_ON
CPH6701-TL-EQ4506
1
2
3 4
5
6
C4527
10V B4.7u
CPH6701-TL-EQ4509
1
2
3 4
5
6
33uHL4501
± 0.5%4700
R4550
33kR4502
R452847k
CPH6702-TL-EQ4510
1
2
3 4
5
6
D_2.8V
EP_2.8V
100kR4543
XXC4545
± 0.5%100k
R4508
0.01u
F
C4529
50V
± 0.5%68k
R4546
BL_REG_UNREG
CPH6102-TL-EQ4501
1234 5 6
4.7u25V
C4546
REG_GND
C45354.7u
C45344.7u
L45114.7uH
BL_REG
22kR4511
10u16V
C4551
100kR4542
± 0.5%47k
R4535
VTR_UNREG
0R4517
33k
R45
18
4700R4525
± 0.5%22k
R4501
10u6.3V
A
C4536
L450222uH
2SA1832F-Y/GR(TPL3)Q4504
100kR4532
22u6.3V
A
C4547
22u4VA
C4559
CAP_VS
1SS383(T5RSONY1)D4503
Q4511SI2304DS-T1
T4501
1
2
3
4 5
6
7
8
10u6.3V
A
C4556
0.001uB
C4519
10u6.3V
A
C4553
0.00
1uB
C45
18
470pB
C4515
22u4VA
C4557
REG_GND
0.001uB
C4516
EP_4.75V
47kR4531
4.7uHL4509
C45314.7u
10V B
0.001uB
C4520
RP_4.75V
± 5%
R45090
0R4510
10u10V
A
C4544
XXR4549
R4530XX
1uHL4522
10k
R45
20
SI2304DS-T1Q4512
0R4554
0.1uC4538
10u6.3V
A
C4541
HN1A01FE-Y/GR(TPLR3)Q4520
6
2
1
3
5
4
0.01uB
C4507
4.7u10V B
C4521
± 0.5%100k
R4539
15k
R45
40
2.2uF
C4555XXD4501
± 0.5%36k
R4527
0.00
1uB
C45
17
L45174.7uH
4700R4514
2SC4738F-Y/GR(TPL3)Q4517
XXL4512
XXR4553
CPH6702-TL-EQ4503
1
2
3 4
5
6
XXR4516
0.001uB
C4513
XXD4504
D_1.5V
22uHL4503
2200
pB
C45
12
22kR4538
CAP_ERROR
2SB798-T1-DLDKQ4502
± 0.5%27k
R4526
HN
1C01
FE-Y
/GR
(TP
LR3)
Q45
16
6
2
1
3
5
4
EP_13.3V
C/D_VS_D1.5V XXC4524
CPH6702-TL-EQ4505
1
2
3 4
5
6
15kR4506
2.2uF
C4554
4.7uHL4507
0.1uB
C4543
0R
4513
2SA1832F-Y/GR(TPL3)Q4515
6800R4503
4.7uHL4508
PANEL_-15.3V
22u6.3V
A
C4550
L45154.7uH
VTR_DD_ON
MT_5V
0R
4521
HN1C01FE-Y/GR(TPLR3)Q4507
6
2
1
3
5
4
L450533uH
Q4513RN1104F(TPL3)
PLL_1.5V
10u10VA
C4525
C454822u
6.3VA
R452922k
10u6.3V
A
C4539
22uHL4516
A_4.75V
CAM_-6.5V
± 0.5%100k
R4534
DRUM_VS
± 0.5%15k
R4536
C45324.7u10V B
HN1A01FE-Y/GR(TPLR3)Q4518
6
21
3
5
4
XXR4564
1500
pB
C45
11
AU_2.8V
4700pB
C4501
± 0.5%220k
R4541
C454910u6.3V
A
1uHL4520
4.7u10V
B
C4523
0R4505
CAM_12V
± 0.5%220k
R4545
C45224.7u10V
B
1uHL4513
1SS383(T5RSONY1)D4502
L45144.7uH
4.7u10V
B
C4526
R1121N191B-TLIC4505
12
3 45
XXC4540
220p CHC4502
0.1uB
C4505
0.1u BC4503
0.1uB
C4506
0.047uB
C4504
REG_GND
REG_GND
EP_13.3V
EP_4.75V
EP_2.8V
MT_5V
A_4.75V
EP_13.3V
AU_4.75V
AU_2.8V
REG_GND
XXC4514
1
A
VTR_UNREG
VTR_UNREG
CAP_ERROR
DRUM_ERROR
CAP_VS
DRUM_VS
CAP_ERROR
CAP_VS
DRUM_ERROR
DRUM_VS
OU
TPU
T-7
NO
NIN
V_I
NP
UT-
5
BO
OT_
CA
P_L
-2
INV
_IN
PU
T-3
MOS_GATE-4
OUTPUT_GND-4,5,6,7
STANDBY-7
INV
_IN
PU
T-7
OU
TPU
T_M
ON
ITO
R-2
SOFT_START
OUTPUT-3
INV
_IN
PU
T-6
BOOT_CAP_H-6
CO
MP
OUTPUT-4
OU
TPU
T_V
CC
-7
OU
TPU
T-1
RT
OU
TPU
T_V
CC
-4,5
,6
OU
TPU
T_M
ON
ITO
R-5
BO
OT_
CA
P_H
-2
OU
TPU
T_M
ON
ITO
R-3
OUTPUT_GND-1,2,3
BOOT_CAP_H-5
OUTPUT_MONITOR-4
FEED_BACK-3
VREF(1.5V)
NO
NIN
V_I
NP
UT-
6
MO
S_G
ATE-
1N
ON
INV
_IN
PU
T-7
FEED
_BA
CK
-1
BO
OT_
CA
P_H
-7
OUTPUT_VCC-1,2,3
FEED_BACK-5
CT
BOOT_CAP_L-4
OU
TPU
T-2
FEED
_BA
CK
-6
OU
TPU
T_M
ON
ITO
R-6
OUTPUT-6
INV_INPUT-4
FEED
_BA
CK
-2
SCP
BOOT_CAP_L-5
STANDBY-3 BOOT_CAP_H-3
MOS_DUTY
BO
OT_
CA
P_H
-1O
UTP
UT_
MO
NIT
OR
-7
INV
_IN
PU
T-1
BO
OT_
CA
P_L
-7
INV
_IN
PU
T-5
BOOT_CAP_H-4
FEED
_BA
CK
-7
STANDBY
VCC
BOOT_CAP_L-3
BOOT_CAP_L-6
FEED_BACK-4
INV
_IN
PU
T-2
OUTPUT-5
GND
BO
OT_
CA
P_L
-1
OU
TPU
T_M
ON
ITO
R-1
Vout GND VDD
N.C.
CE
IC4501DC-DC CONVERTER
Q4502,4504,4507 MT 5V REG
Q4508,4509,4510 SWITCHING
Q4505,4506,4511,4512 SWITCHING
SWITCHING
DC-DC CONVERTER TRANSFORMER
SWITCHING
EMERGENCY DETECT
Q4514,4515,4516 CAM 12V REG
Q4517,4518CAM -6.5V REG EP 13.3V REG
Q4519,4520-15.3V REG
IC4505D1.9V REG
9
G
E
8 15
F
5 18
J
C
143 7 114 1713
I
2
B
6 10 1612
D
H
XX MARK:NO MOUNT
DC-DC CONVERTER(DD BLOCK)VA-117 BOARD(4/6)
16
Drum servo (speed and phase)
REC/PBREC
Capstan servo (speed and phase)
SIGNAL PATHPB
14 (5/6)
9 (2/6)
(6/6)16
(3/6)10
(3/6)11
(1/6)1
(2/6)8
(2/6)4
(6/6)15
(6/6)17
Note :The components identified bymark 0 or dotted line with mark0 are critical for safety.Replace only with part numberspecified.
Note :Les composants identifiés parune marque 0 sont critiquespour la sécurité.Ne les remplacer que par unepièce portant le numéro spécifié.
DCR-TRV16/TRV16E/TRV18/TRV18E/TRV116E/TRV118E
COVERCOVER
4-31 4-32
4-2. SCHEMATIC DIAGRAMS VA-117 BOARD SIDE A VA-117 BOARD SIDE B4-2. SCHEMATIC DIAGRAMS VA-117 BOARD SIDE A VA-117 BOARD SIDE B
VA-117 (5/6)
For Schematic Diagram• Refer to page 4-81 for printed wiring board.
7.8
8.1
7.8
8.0
8.2
7.8
0.1
7.6
8.2
8.2
0.1
3.1
R8.2P0
8.2
R0/P8.2
8.2
P8.2R0.2
R0/P8.2
P0.1R3.1
8.2
P8.2R0
R8.2P0
8.2
R0.2P8.2
R8.2/P0
R8.2P0
P8.2R0.2
8.2
8.2
NO MARK:REC/PB MODE R :REC MODE P :PB MODE
P8.2R0.2
(DCR-TRV16/TRV16E/TRV116E)
(DCR-TRV18/TRV18E/TRV118E)
(DCR-TRV18/TRV18E/TRV118E)
F46061.4A/32V
XXR4602
1MR4615
4.7uHL4601
FAST_CHARGE
2SB1122-ST-TDQ4603
1
23
47kR4611
RN2104F(TPL3)Q4606
12
3
SHOE_ON
100kR4604
REG_GND
C460422u16V
TA B
F46051.4A/32V
BL_REG_UNREG
1MR4605
BATT_UNREG
SHOE/MT_UNREG
RN1104F(TPL3)Q4604
12
3
C460622u16V
TA B
6800R4609
INIT_CHARGE_ON
0.022uB
C4603
01ZA8.2(TPL3)D4601
123
BATT_SIG
1uB
C4608
SSM3K03FE(TPL3)Q4601
12
3
1kR4608
PRT_HEAD_UNREG
C460522u16VTA B
F46031.4A/32V
100R4614
XXR4603
F46041.4A/32V
2SJ3
05(T
E85L
)Q
4609
12
3
VTR_UNREG
0.1uB
C4602
1kR4601
F46021.4A/32V
1uB
C4607
RN2104F(TPL3)Q4607
1
2
3
XXR4616
0.1uB
C4601
BATT/XEXT
47kR4610
1kR4618
1kR4617
2SJ305(TE85L)Q4608
12
3
100R4612
1MR4613
RN1104F(TPL3)Q4605
12
3
C/D_VS_D1.5V
10R4607
F46011.4A/32VLF4601
XXR4606
1SS383(T5RSONY1)D4602
23
14
TPCS8302(TE12L)Q4610
1
4
23
8
5
67
TPCS8302(TE12L)Q4602
1
4
23
8
5
67
Q4611TPC6101(TE85R)
1
3
4256
6PCN4601
1
2
3
4
5
6
REG_GND
1
A
BATT_SIG
BATT/XEXT
ACV_GND
BATT_GND
BATT_UNREG
ACV_UNREG
SWITCH
SWITCHCHARGE SWITCH
CHARGE SWITCH
Q4605-4609 SWITCH
SWITCHING
(SHOE_GND)
S
BATTERYTERMINAL
DC IN
BT901
9
G
E
8
F
5
C
3 7 1142
B
6 10 12
D
XX MARK:NO MOUNT
CHARGE(FU BLOCK)VA-117 BOARD(5/6)
16
18 (6/6)
(4/6)14
19 (6/6)
(6/6)20
Note :The components identified bymark 0 or dotted line with mark0 are critical for safety.Replace only with part numberspecified.
Note :Les composants identifiés parune marque 0 sont critiquespour la sécurité.Ne les remplacer que par unepièce portant le numéro spécifié.
DCR-TRV16/TRV16E/TRV18/TRV18E/TRV116E/TRV118E
COVERCOVER
4-33 4-34
4-2. SCHEMATIC DIAGRAMS VA-117 BOARD SIDE A VA-117 BOARD SIDE B4-2. SCHEMATIC DIAGRAMS VA-117 BOARD SIDE A VA-117 BOARD SIDE B
VA-117 (6/6)
For Schematic Diagram• Refer to page 4-81 for printed wiring board.• Refer to page 4-90 for waveforms.
4.7
0
0
2.8
2.6
-0.8
0 0
-0.8
-0.8
1.7
2.6
0
R0/P2.3
2.6
0.1
0.3
2.0
2.1
1.0
2.4
0.5
4.7
4.7
1.3
1.3
1.8
1.6
4.7
4.7
2.2
0
0.1
4.7 0
2.8
2.5
2.6
2.6
7
6
5
8
9
10
12
3
4
NO MARK:REC/PB MODE R :REC MODE P :PB MODE
(DCR-TRV18/TRV18E/TRV118E)
:(DCR-TRV18/TRV18E/TRV118E):(DCR-TRV16/TRV16E/TRV116E)
C41070.01u
B
C41051u B
C41180.01u B
C41121uB
C41061uB
C41040.22u
B
C41030.033u
B
R410722k
± 0.5%
C41141uB
C412310u 6.3V A
C4124XX
C411110u
6.3V
C41130.01u
B C41160.1uB
L410210uH
FB41010uH
L410110uH
AN2225NFHQBA
IC4101
1 2 3 4 5 6 7 8 9 10 11 12
13
14
15
16
17
18
19
20
21
22
23
24
252627282930313233343536
37
38
39
40
41
42
43
44
45
46
47
48
0.01uB
C4119
10kR4110
0.01uB
C4115
2SC4738F-Y/GR(TPL3)Q4101
4700R4102
100R4103
0.01uB
C4101 220kR4104
4700R4101
R41091k
R41081k
BC41102.2u
B2.2uC4108
B2.2uC4109
B2.2u
C4121
B2.2u
C4117
R41061k
Q4102RN2104F(TPL3)
R41051k
C4102XX
HN1C01FE-Y/GR(TPLR3)Q4103
3
5
4
6
2
1
C4V220u
C4120
4V220uC4122
22pCH
C4125
2200R4111
33R4112
33R4113
33R4114
33R4115
33R4116
33R4117
1kR4118
1kR4119
1kR4120
1kR4121
HP_JACK_IN
REG_GND
XMIC_MONO
EXT_MIC_JACK
AU_LINE_I/O_R
INIT_CHARGE_ON
SIRCS_SIG
EVF_R
BATT/XEXT
EVF_G/BW_Y
MF_B
100PCN4002
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
PANEL_XHD
EVF_B
MF_A
XVSP_SCK
XF_TALLY_LED
XCS_AU1
G
ZOOM_MIC_CONT
BEEP_IN
AU_LINE_I/O_L
XAUDIO_IN
VSP_SO
FAST_CHARGE
KEY_AD6
XCS_EVF
PANEL_XVD
IR_ON
BATT_SIG
SHOE_ON
MF_LED
VCO
SIRCS_PWM
PRT_HEAD_UNREG
01ZA
8.2(
TPL3
)D
4003
0R4001
20PCN4001
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
0.1uB
C4003
SHOE/MT_UNREG
0.1uB
C4001
0R4005
REG_GND
0R4003
01ZA
8.2(
TPL3
)D
4005
0R4002
0.1uB
C4002
01ZA
8.2(
TPL3
)D
4001
01ZA
8.2(
TPL3
)D
4004
UD
ZSTE
-178
.2B
D40
06
0R4004
SHOE_MIC_L
20p
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
REG_GND
CAM_DD_ON
VTR_DD_ON
XRST_VTR
VD_SO
VD_SCK
1
A
BATT_UNREG
VTR_UNREG
REG_1.5V
D_1.5V
PLL_1.5V
D_1.9V
MT_5V
RP_4.75V
A_4.75V
D_2.8V
CAM_12V
A_2.8V
EP_13.3V
CAM_-6.5V
CAP_VS
DRUM_VS
DRUM_ERROR
CAP_ERROR
IC2301_L
REC_OUT_R
REC_OUT_L
IC2301_R
PB_IN_R
PB_IN_L
VD
_SO
VD
_SC
K
XC
S_I
C41
01
IC41
01_C
_OU
T
IC41
01_Y
_OU
T
Y_O
UT
DR_C_OUT
AC
C_C
ON
T
AG
C_C
ON
T
S_Y
_I/O
VID
EO_I
/O
DR
_C_O
UT
DR_Y_OUT
DR
_Y_O
UT
DR
_V_O
UT
DR_V_OUT
SHOE_CONT_AD
S_Y_I/O
XCS_IC4101
HS_TXD
DRUM_ERROR
HOTSHOE_ID2
ACC_CONT
DRUM_VS
HS_SCK
HS_RXD
VD_SO
AGC_CONT
VIDEO_I/O
IC4101_Y_OUT
HOTSHOE_ID1
CAP_ERROR
VTR_DD_ON
IC4101_C_OUT
VD_SCK
EXT_STROBO
S_C_I/O
CAP_VS
C_OUT
Y_OUT
HS_HDS
CAM_DD_ON
LANC_SIG
HOTSHOE_ID2
HS_SCK
HOTSHOE_ID1
HS_HDS
SHOE_CONT_AD
LANC_SIG
EXT_STROBO
HS_RXD
HS_TXD
C_O
UT
S_C
_I/O
DRUM_VS
DRUM_ERROR
CAP_VS
CAP_ERROR
CAM_DD_ON
VTR_DD_ON
VD_SO
VD_SCK
C_G
CA
_CO
NT
AG
C_V
OU
T
C_I
N2
MA
IN_V
CC
C_I
N3
D_G
ND
C_I
N4
D_V
CC
SI
XS
CK
XC
S
C_G
ND
SDC
DRV_C_OUT
C_VCC
Y_GND
Y_INV
DRV_Y_OUT
Y_VCC
V_GND
V_INV
DRV_V_OUT
V_VCC
IR_V_OUT
MM
_TC
2
4FS
C_O
UT
MM
_TC
3
XTA
L
PLL
_VC
C
EXTA
L
AP
C_F
IL
BG
T_O
UT
PLL
_GN
D
INP
UT_
C_O
UT
VR
EF
INP
UT_
Y_O
UT
IR
MAIN_GND1
Y_IN1
MAIN_GND2
SYNC_SEP_TC
Y_IN2
CLAMP_TC1
Y_IN3
CLAMP_TC2
Y_IN4
Y_GCA_CONT
C_IN1
VIDEO IN/OUT,AGC
IC4101
BATT_SIG
IC4101_Y_OUT
REG_GND
A_4.75V
EVF_G/BW_Y
PB_IN_R
CAM_12V
MT_5V
CAM_-6.5V
AGC_CONT
CAP_VS
HP_JACK_IN
SDC_IN
XCS_EVF
XRST_VTR
HS_TXD
CAP_VS
DRUM_VS
REG_GND
REC_OUT_L
DRUM_VS
ZOOM_MIC_CONT
VD_SCK
HOTSHOE_ID1
REG_GND
VIDEO_I/O
BATT_UNREG
VD_SO
D_1.5V
KEY_AD6
REG_GND
VTR_UNREG
LANC_SIG
IC2101_C_OUT
VTR_DD_ON
MT_GND
EXT_MIC_JACK
SIRCS_PWM
XF_TALLY_LED
REG_GND
PLL_1.5V
AU_LINE_I/O_R
PB_IN_L
D_2.8V
REG_1.5V
MF_LED
D_1.9V
CAM_DD_ON
VSP_SO
IC4101_C_OUT
IC4301_R
AU_LINE_I/O_L
XCS_AU1
SHOE_CONT_AD
REC_OUT_R
RP_4.75V
XVSP_SCK
BATT_XEXT
PANEL_XHD
DRUM_ERROR
EP_13.3V
HOTSHOE_ID2
PANEL_XVD
MF_B
MT_5V
MT_GND
ACC_CONT
MF_A
HS_SCK
IC4301_L
BEEP_IN
REG_GND
EVF_R
D_2.8V
HS_RXD
IR_ON
SIRCS_SIG
XVIDEO_IN
HS_HDS
XAUDIO_IN
A_2.8V
FAST_CHARGE
IC2101_Y_OUT
VCO
EVF_B
SHOE_ON
D_1.5V
XCS_IC4101
A_2.8V
D_2.8V
S_C_I/O
A_4.75V
EXT_STROBO
XMIC_MONO
G
REG_GND
CAP_ERROR
INIT_CHARGE_ON
REG_1.5V
S_Y_I/O
TXD
SHOE_UNREG_GND
SHOE_MT_GND
SHOE_MIC_L
SHOE_ID1
LANC_SIG
SHOE_UNREG
SHOE_MT_GND
PRT_HEAD_UNREG
SHOE_CONT_AD
SCK
RXD
PRT_HEAD_UNREG
SHOE_MIC_GND
SHOE_ID2
HDS
SHOE_UNREG_GND
SHOE_UNREG_GND
SHOE_UNREG
STBY_ON
SHOE_MIC_GND
SHOE_UNREG
SHOE_ID2
PRT_HEAD_UNREG
STBY_ON
SHOE_UNREG
PRT_HEAD_UNREG
RXD
SHOE_CONT_AD
TXD
SHOE_UNREG_GND
HDS
SHOE_UNREG_GND
SHOE_MIC_L
SHOE_MT_GND
SCK
RXD
STBY_ON
TXD
HDS
SHOE_MT_GND
SHOE_ID1
LANC_SIG
SCK
LANC_SIG
SHOE_CONT_AD
SHOE_UNREG
SHOE_UNREG_GND
SHOE_MT_GND
PRT_HEAD_UNREG
SHOE_MIC_GND
SHOE_ID2
SHOE_MIC_L
SHOE_ID1
SHOE_UNREG_GND
BUFFER
SWITCH
SWITCH
FP-436FLEXIBLE
INTELLIGENTACCESSORYSHOE
VIDEO I/O(TA BLOCK)XX MARK:NO MOUNT
VA-117 BOARD(6/6)
9
G
K
E
8 15
F
5
J
C
143 7 114 17
M
13
I
2
B
6 10 1612
L
D
H
16
REC
SIGNAL PATHREC/PB
Drum servo (speed and phase)
PB
SIGNAL PATH
REC
VIDEO SIGNAL
PB
Y/CHROMA SIGNALAUDIO
YCHROMA
Capstan servo (speed and phase)
TOVC-280 BOARD(15/15)CN1007
(PAGE 4-65)
18
19 (5/6)
(5/6)18
(4/6)15
(4/6)16
(4/6)17
(2/6)3
(2/6)6
(1/6)2
13 (3/6)
12 (3/6)
20 (5/6)
15P 8P
DCR-TRV16/TRV16E/TRV18/TRV18E/TRV116E/TRV118E
COVERCOVER
4-35 4-36FP-100/FP-228/FP-102
4-2. SCHEMATIC DIAGRAMS FP-100, FP-228, FP-102 FLEXIBLE BOARD4-2. SCHEMATIC DIAGRAMS FP-100, FP-228, FP-102 FLEXIBLE BOARD
27P
1LM_LOAD
TO VC-280 BOARD (12/15) CN1010 (PAGE 4-60)
2LM_LOAD
3LM_UNLOAD
4LM_UNLOAD
5DEW+
6DEW-
7MODE A
8MODE B
9MODE C
10SW_COM/SW_GNDS903
D901
4PCN901
S901
1
A
MIC
/REC
_SW
_GN
D
TAP
E_EN
D
XR
EC_P
RO
OF
HA
LL_G
ND
DEW
+
CH
IME_
VD
D
TREE
L-
SW
_CO
M/S
W_G
ND
LM_U
NLO
AD
TOP
/EN
D_G
ND
DEW
-
XC
CD
OW
N_S
W
TAP
E_LE
D_A
XM
OD
E_S
W_A
XM
OD
E_S
W_B
LM_U
NLO
AD
LM_L
OA
D
SR
EEL-
CH
IME_
SD
A
HA
LL_V
CC
SR
EEL+
TAP
E_TO
P
TAP
E_LE
D_K
TREE
L+
CH
IME_
SC
K
LM_L
OA
D
XM
OD
E_S
W_C
(CC DOWN)
(TAPE LED)
M M903LOADING MOTOR
S902 MODESWITCH
FLEXIBLE
FP-100
Vcc -
+ G
-Vcc
G+
H902T REELSENSOR
H901S REELSENSOR
Q902TAPE TOPSENSOR
Q901TAPE ENDSENSOR
(REC PROOF)
FP-102FLEXIBLE
DEWSENSOR
FP-228FLEXIBLE
B
4
D
C
732 65
16
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27
Schematic diagram of the VC-280 board are not shown.Pages from 4-37 to 4-66 are not shown.
DCR-TRV16/TRV16E/TRV18/TRV18E/TRV116E/TRV118E
COVERCOVER
LinkLink
4-3. PRINTED WIRING BOARDS
PD-161 BOARD
FP-100, FP-228, FP-102 FLEXIBLE BOARDS
FP-444 FLEXIBLE BOARD VA-117 BOARD (SIDE B)
MA-409 BOARD VA-117 BOARD (SIDE A)
JK-218 BOARD CK-108 BOARD (SIDE B)
JK-217 BOARD CK-108 BOARD (SIDE A)
FP-443 FLEXIBLE BOARD LB-077 BOARD
CD-365 BOARD
FB-219 BOARDFB-219 BOARD
PD-161 BOARD
FP-100, FP-228, FP-102 FLEXIBLE BOARDS
FP-444 FLEXIBLE BOARD VA-117 BOARD (SIDE B)
MA-409 BOARD VA-117 BOARD (SIDE A)
JK-218 BOARD CK-108 BOARD (SIDE B)
JK-217 BOARD CK-108 BOARD (SIDE A)
FP-443 FLEXIBLE BOARD LB-077 BOARD
CD-365 BOARD
CIRCUIT BOARDS LOCATION
WAVEFORMSCOMMON NOTE FOR PRINTED WIRING BOARDS
MOUNTED PARTS LOCATION FLEXIBLE BOARDS LOCATIONCIRCUIT BOARDS LOCATION
WAVEFORMSCOMMON NOTE FOR PRINTED WIRING BOARDS
MOUNTED PARTS LOCATION FLEXIBLE BOARDS LOCATION
DCR-TRV16/TRV16E/TRV18/TRV18E/TRV116E/TRV118E
COVERCOVER 4-2. SCHEMATIC DIAGRAMS 4-3. PRINTED WIRING BOARDS4-2. SCHEMATIC DIAGRAMS 4-3. PRINTED WIRING BOARDS
4-67 4-68 CD-365/FP-443
CD-365 (CCD IMAGER) PRINTED WIRING BOARD4-3. PRINTED WIRING BOARDS
FP-443 FLEXIBLE BOARD
MOUNTED PARTS LOCATIONMOUNTED PARTS LOCATION
1
6
R201
R202S202
S203
EDIT SEARCH +
EDIT SEARCH –
S201(EJECT SW)
1-684-257- 21
FP-443 FLEXIBLE
1112
• : Uses unleaded solder.
For printed wiring boards• Refer to page 4-93 for parts location.• This board is six-layer print board. However, the pat-
terns of layers two to five have not been included inthe diagram.
There are a few cases that the part printed onthis diagram isn’t mounted in this model.
DCR-TRV16/TRV16E/TRV18/TRV18E/TRV116E/TRV118E
COVERCOVER 4-2. SCHEMATIC DIAGRAMS 4-3. PRINTED WIRING BOARDS4-2. SCHEMATIC DIAGRAMS 4-3. PRINTED WIRING BOARDS
4-69 4-70
JK-217 (STEADY SHOT, A/D, IN/OUT), JK-218 (DIGITAL IN/OUT) PRINTED WIRING BOARD
JK-217/JK-218
MOUNTED PARTS LOCATIONMOUNTED PARTS LOCATION
S VIDEO
AUDIO/VIDEO
1112
DV IN/OUT
DV OUT
1112
Note
(TRV16/TRV16E:E,HK,AUS,CH/TRV18/TRV18E:E,HK,AUS,CH,JE/TRV116E/TRV118E)
(TRV16E:AEP,UK,EE,NE/TRV18E:AEP,UK,EE,NE)
NoteDV IN/OUT
DV OUT
• : Uses unleaded solder.
For printed wiring boards• Refer to page 4-93 for parts location.• This board is six-layer print board. However, the pat-
terns of layers two to five have not been included inthe diagram.
There are a few cases that the part printed onthis diagram isn’t mounted in this model.
For printed wiring boards• This board is six-layer print board. However, the pat-
terns of layers two to five have not been included inthe diagram.
There are a few cases that the part printed onthis diagram isn’t mounted in this model.
• AbbreviationEE : East European modelNE : North European modelHK : Hong Kong model
AUS : Australian modelCH : Chinese modelJE : Tourist model
DCR-TRV16/TRV16E/TRV18/TRV18E/TRV116E/TRV118E
COVERCOVER 4-2. SCHEMATIC DIAGRAMS 4-3. PRINTED WIRING BOARDS4-2. SCHEMATIC DIAGRAMS 4-3. PRINTED WIRING BOARDS
4-71 4-72 MA-409/FP-444
MA-409 (MIC IN, HP JACK, REMOTE CONTROL RECEIVER, SWITCH) PRINTED WIRING BOARD FP-444 FLEXIBLE BOARD
MOUNTED PARTS LOCATIONMOUNTED PARTS LOCATION
S301
R301 R302
S302
FADER
FOCUS (INFINITY)
1-684-258- 21
1
16
8
FP-444 FLEXIBLEMIC
(PLUG IN POWER)
• : Uses unleaded solder.
For printed wiring boards• Refer to page 4-93 for parts location.• This board is six-layer print board. However, the pat-
terns of layers two to five have not been included inthe diagram.
There are a few cases that the part printed onthis diagram isn’t mounted in this model.
DCR-TRV16/TRV16E/TRV18/TRV18E/TRV116E/TRV118E
COVERCOVER 4-2. SCHEMATIC DIAGRAMS 4-3. PRINTED WIRING BOARDS4-2. SCHEMATIC DIAGRAMS 4-3. PRINTED WIRING BOARDS
4-73 4-74FB-219/PD-161
FB-219 (MANUAL FOCUS SENSOR), PD-161 (RGB DRIVE, TIMING GENERATOR, LCD DRIVE, BACK LIGHT) PRINTED WIRING BOARD
MOUNTED PARTS LOCATIONMOUNTED PARTS LOCATION
11
12
• : Uses unleaded solder.
For printed wiring boards• This board is six-layer print board. However, the pat-
terns of layers two to five have not been included inthe diagram.
There are a few cases that the part printed onthis diagram isn’t mounted in this model.
For printed wiring boards• Refer to page 4-93 for parts location.• This board is six-layer print board. However, the pat-
terns of layers two to six have not been included in thediagram.
There are a few cases that the part printed onthis diagram isn’t mounted in this model.
DCR-TRV16/TRV16E/TRV18/TRV18E/TRV116E/TRV118E
COVERCOVER 4-2. SCHEMATIC DIAGRAMS 4-3. PRINTED WIRING BOARDS4-2. SCHEMATIC DIAGRAMS 4-3. PRINTED WIRING BOARDS
4-75 4-76 LB-077/FP-100/FP-228/FP-102
FP-100 (MODE SWITCH), FP-228 (DEW SENSOR), FP-102 (TAPE TOP/END SENSOR, S/T REEL) FLEXIBLE BOARDLB-077 (EVF, EVF BACK LIGHT) PRINTED WIRING BOARD
1-677-085-
1-677-049-
11
11
110
101
127
M
S902MODE SWITCH
DEWSENSOR
M903LOADINGMOTOR
D901(TAPE LED)
S903(CC DOWN)
S901(REC PROOF)
Q902TAPE TOPSENSOR
Q901TAPE ENDSENSOR
H902T REEL
SENSOR
H901S REEL
SENSOR
CN901
FP-102 FLEXIBLE BOARD
FP-100 FLEXIBLE BOARD
FP-228FLEXIBLE BOARD
1112
• : Uses unleaded solder. (LB-077 board)
For printed wiring boards• This board is six-layer print board. However, the pat-
terns of layers two to five have not been included inthe diagram.
There are a few cases that the part printed onthis diagram isn’t mounted in this model.
DCR-TRV16/TRV16E/TRV18/TRV18E/TRV116E/TRV118E
COVERCOVER 4-2. SCHEMATIC DIAGRAMS 4-3. PRINTED WIRING BOARDS4-2. SCHEMATIC DIAGRAMS 4-3. PRINTED WIRING BOARDS
4-77 4-78CK-108
CK-108 (SWITCH, CONNECTOR) PRINTED WIRING BOARD
MOUNTED PARTS LOCATIONMOUNTED PARTS LOCATION
(STOP) (REW) (PLAY) (FF) (PAUSE)
11
12
• : Uses unleaded solder.
For printed wiring boards• Refer to page 4-94 for parts location.• This board is six-layer print board. However, the pat-
terns of layers two to five have not been included inthe diagram.
There are a few cases that the part printed onthis diagram isn’t mounted in this model.
DCR-TRV16/TRV16E/TRV18/TRV18E/TRV116E/TRV118E
COVERCOVER 4-2. SCHEMATIC DIAGRAMS 4-3. PRINTED WIRING BOARDS4-2. SCHEMATIC DIAGRAMS 4-3. PRINTED WIRING BOARDS
4-79 CK-1084-80
MOUNTED PARTS LOCATIONMOUNTED PARTS LOCATION
11
12
• : Uses unleaded solder.
CAUTION :Danger of explosion if battery is incorrectly replaced.Replace only with the same or equivalent type.
DCR-TRV16/TRV16E/TRV18/TRV18E/TRV116E/TRV118E
COVERCOVER 4-2. SCHEMATIC DIAGRAMS 4-3. PRINTED WIRING BOARDS4-2. SCHEMATIC DIAGRAMS 4-3. PRINTED WIRING BOARDS
4-81 4-82VA-117
VA-117 (RGB DRIVE, TG, AUDIO, MIC AMP, DC-DC CONVERTER, CHARGE, VIDEO I/O) PRINTED WIRING BOARD
MOUNTED PARTS LOCATIONMOUNTED PARTS LOCATION
• : Uses unleaded solder.
For printed wiring boards• Refer to page 4-94 for parts location.• This board is six-layer print board. However, the pat-
terns of layers two to five have not been included inthe diagram.
There are a few cases that the part printed onthis diagram isn’t mounted in this model.
DCR-TRV16/TRV16E/TRV18/TRV18E/TRV116E/TRV118E
COVERCOVER 4-2. SCHEMATIC DIAGRAMS 4-3. PRINTED WIRING BOARDS4-2. SCHEMATIC DIAGRAMS 4-3. PRINTED WIRING BOARDS
4-83 4-84 VA-117
MOUNTED PARTS LOCATIONMOUNTED PARTS LOCATION
• : Uses unleaded solder.
Printed wiring board of the VC-280 board are not shown.Pages from 4-85 to 4-88 are not shown.
DCR-TRV16/TRV16E/TRV18/TRV18E/TRV116E/TRV118E
COVERCOVER
4-89 4-90CD-365/PD-161/VA-117
4-4. WAVEFORMS
CD-365 BOARD
2 IC5001 3,4
6 Q5001 E
1 IC5001 1,2
7.5 Vp-p
H
7.5 Vp-p
H
4 IC5001 q;
3.0 Vp-p
56 nsec
56 nsec
1.2Vp-p
3 IC5001 8
H
1.2Vp-p
H
5 IC5001 qa
3.4 Vp-p
PD-161 BOARD REC/PB
2 IC5501 ws
3 IC5501 wf
1 IC5501 w;
3.8Vp-p
H
9 IC5502 wh
2.9 Vp-p
85 nsec
3.8Vp-p
3.8Vp-p
H
H
q; IC5651 2
3.1 Vp-p
6 IC5501 rh
H
5 IC5501 rj
H
4 IC5501 rk
480 mVp-p
450 mVp-p
500 mVp-p
H
7 IC5502 1
2.8Vp-p
H
8 IC5502 rk
2.8Vp-p
V
39 µsec
VA-117 BOARD
1 IC4101 7 CAMERA REC S JACK IN
2 IC4101 qf CAMERA REC S JACK IN
H
qd IC4201 wf REC/PB
7.0 Vp-p0.4Vp-p
H
H1.4 Vp-p
H
1.8 Vp-p
3 IC4101 qk CAMERA REC/PB S JACK IN
4 IC4101 ws CAMERA REC/PB AV JACK IN
2.2Vp-p
H
5 IC4101 ef LINE REC(S-VIDEO)
1.0 Vp-p
H
6 IC4101 eh LINE REC(S-VIDEO)
0.8 Vp-p
H
7 IC4101 el LINE REC (S-VIDEO)
H
420 mVp-p
H
0.5Vp-p
8 IC4101 rs LINE REC (AV VIDEO)
9 IC4101 rh CAMERA REC/PB AV JACK or S JACK IN
450 mVp-pH
H
q; IC4101 rk LINE REC (S-VIDEO)
1.3 Vp-p
qa IC4201 w; REC/PB
6.2Vp-p
H
qs IC4201 ws REC/PB
7.0 Vp-p
H
qf IC4201 rh REC/PB
350 mVp-p
H
qh IC4201 rk REC/PB
350 mVp-p
H
qg IC4201 rj REC/PB
350mVp-p
H
qj IC4202 1 REC/PB
2.8Vp-p
H
qk IC4202 rk REC/PB
2.8Vp-p
V
CD-365 BOARD PD-161 BOARD VA-117 BOARD SIDE A VA-117 BOARD SIDE BCD-365 BOARD PD-161 BOARD VA-117 BOARD SIDE A VA-117 BOARD SIDE B
4-91
DCR-TRV16/TRV16E/TRV18/TRV18E/TRV116E/TRV118E
COVERCOVER
VA-117
VA-117 BOARD
w; IC4501 tk REC/PB
0.8 Vp-p
2.3 µsec
wa IC4501 yf REC/PB
0.8 Vp-p
2.3 µsec
ql IC4202 wh REC/PB
2.1 Vp-p
92 nsec
VA-117 SIDE A VA-117 SIDE BVA-117 SIDE A VA-117 SIDE B
4-93
DCR-TRV16/TRV16E/TRV18/TRV18E/TRV116E/TRV118E
COVERCOVER
* C5001 B-1* C5002 B-2* C5003 B-1* C5004 B-1
CN5001 A-1CN5002 A-2
IC5001 B-1* IC5001 B-1
* L5001 B-2
* Q5001 B-2
* R5001 B-1R5002 A-1
CD-365 BOARD
* C5301 A-3* C5302 A-3
CN5305 B-3
* D5301 D-1* D5302 B-2
* FB5301 D-1* FB5302 B-3* FB5303 A-2* FB5304 A-2* FB5305 B-2* FB5307 B-3* FB5308 C-1* FB5309 B-1* FB5310 B-2
J5301 D-1J5302 B-2
* R5301 C-1* R5302 B-1* R5303 B-2* R5304 B-2* R5305 B-3
SE5301 B-3SE5302 A-3
* VD5301 B-1* VD5302 D-1* VD5303 B-2* VD5304 C-1* VD5305 B-2* VD5306 B-1
JK-217 BOARD
C5901 C-2C5902 B-1
* CN5901 B-2* CN5902 B-1* CN5903 A-1
D5901 A-1D5902 A-1D5903 B-1
* D5904 A-1* D5905 A-1
* FB5901 B-2* FB5902 B-2
FB5903 B-2FB5904 B-2
IC5901 B-1
J5901 C-2J5902 C-3
R5901 B-1
VD5901 B-3VD5902 B-2VD5903 B-2VD5904 B-2
MA-409 BOARD PD-161 BOARD
R5513 B-3R5514 A-2R5515 A-2R5516 C-2R5517 B-1R5518 B-1R5519 B-1R5520 A-2R5521 B-1R5523 C-2R5525 A-2R5528 B-1R5529 B-1R5530 B-1R5531 C-2R5532 B-2R5533 C-1R5534 B-2R5540 B-1R5541 B-1R5552 B-1R5591 B-1R5601 C-6R5602 B-5R5603 B-5R5604 C-6R5605 B-5R5606 B-5R5607 B-5R5608 C-5R5609 D-5R5612 C-5R5613 B-5R5614 B-5R5651 C-4R5652 C-4
RB5501 C-3RB5502 A-1RB5503 B-1
T5601 B-6
VD5651 C-4
C5501 C-3C5503 C-3C5504 B-2C5505 C-2C5506 C-2C5507 C-2C5508 B-2C5509 C-1C5510 C-2C5511 B-3C5512 B-3C5513 C-2C5514 C-2C5515 B-3C5516 B-3C5517 C-3C5518 C-3C5519 C-3C5520 C-2C5521 D-1C5522 C-3C5523 A-2C5524 B-1C5527 C-3C5528 A-3C5530 A-1C5531 A-1C5532 C-1C5603 C-6C5604 B-5C5605 B-5C5606 B-6C5607 D-6
CN5501 A-2CN5601 A-5CN5651 D-1CN5652 B-1CN5653 C-2CN5654 A-4
D5502 B-3D5503 A-3D5504 B-1D5601 B-5D5602 A-5D5603 C-5D5604 D-5
FB5501 C-1FB5502 C-1FB5503 C-1
IC5501 C-3IC5502 B-2IC5601 C-5IC5602 B-5IC5651 C-4
L5501 D-3L5502 C-1L5503 B-2L5601 C-5
Q5502 B-1Q5503 B-1Q5504 B-1Q5505 B-2Q5601 C-5Q5603 B-5Q5604 C-6Q5605 C-6
R5501 C-2R5502 C-2R5503 C-2R5505 C-2R5506 B-3R5507 B-3R5508 B-3R5509 B-3R5510 B-3R5511 B-3R5512 B-3
no mark : side A* mark : side B4-5. MOUNTED PARTS LOCATION
4-3. PRINTED WIRING BOARDS4-3. PRINTED WIRING BOARDS
CD-365/JK-217/MA-409/PD-161
4-94
DCR-TRV16/TRV16E/TRV18/TRV18E/TRV116E/TRV118E
COVERCOVER
R4427 B-1R4428 B-1R4429 B-1
* R4430 A-1* R4431 A-1* R4501 D-5* R4502 D-5* R4503 D-5* R4504 D-5* R4505 D-5* R4506 E-5* R4507 D-5* R4508 D-5* R4509 E-5* R4510 D-5* R4511 E-5* R4512 D-5* R4513 E-5* R4514 E-5* R4515 C-5* R4516 E-5* R4517 E-5* R4518 D-5* R4519 D-5* R4520 D-5* R4521 D-5* R4524 B-6* R4525 B-5* R4526 B-5* R4527 B-5
R4528 E-5R4529 E-5R4530 E-6R4531 D-5R4532 E-5R4533 D-5R4534 E-5R4535 E-5R4536 E-5R4537 D-5R4538 D-5R4539 D-5R4540 D-5R4541 D-5R4542 E-5R4543 D-5R4544 D-5R4545 D-5R4546 D-5
* R4549 E-5R4550 D-5R4551 D-5R4552 D-5
* R4553 E-5* R4554 B-5* R4564 D-5
R4601 A-6R4602 B-6R4603 B-6
* R4604 B-6* R4605 B-6* R4606 A-6* R4607 B-6* R4608 A-6* R4609 A-6* R4610 E-2* R4611 E-2* R4612 E-3* R4613 E-3* R4614 E-3* R4615 E-3* R4616 E-3* R4617 E-3* R4618 E-3
T4501 D-6
* R4109 B-3* R4110 B-3* R4111 C-3* R4112 C-4* R4113 C-4* R4114 C-4* R4115 C-4* R4116 C-4* R4117 C-4* R4118 C-2* R4119 C-2* R4120 C-2* R4121 C-3* R4201 E-2* R4202 E-3* R4203 D-3* R4204 D-2* R4205 D-3* R4206 D-3* R4207 D-3* R4208 D-3
R4209 D-3R4210 D-3
* R4211 D-3* R4212 D-2* R4213 D-2* R4214 D-3* R4215 D-3* R4216 D-3* R4217 D-3* R4218 D-3* R4219 D-2* R4220 D-2
R4221 D-4R4222 D-4R4223 D-4R4224 D-4R4301 D-4R4302 B-3R4303 D-4R4304 C-3R4305 D-3R4306 B-3R4307 B-3R4308 B-3R4309 B-3R4310 C-3R4311 C-3R4316 C-3R4317 C-3R4318 D-3R4319 D-3R4401 B-1R4402 B-1R4403 B-1R4404 B-1R4405 B-1R4406 B-1R4407 A-1
* R4408 B-2* R4409 A-2
R4410 A-2R4411 B-2R4412 B-2R4413 A-2
* R4414 B-2R4415 B-2R4416 A-2R4417 A-2R4418 B-2R4419 A-2R4420 B-2R4421 A-2
* R4422 B-2* R4423 B-2
R4424 B-2R4425 B-2R4426 B-1
VA-117 BOARD
C4403 B-1C4404 A-1C4405 B-1
* C4406 B-1C4407 B-1C4408 B-1C4409 B-1C4410 A-1
* C4411 B-1C4412 A-1C4413 B-1C4414 B-1C4415 A-1C4416 A-1C4417 B-2C4418 B-1C4419 A-2C4420 B-2
* C4421 A-2* C4422 B-2* C4423 B-2
C4424 A-2C4425 A-2C4426 B-2C4427 B-2C4428 B-2C4429 A-2C4430 A-2C4431 B-2
* C4432 B-2C4433 B-2
* C4434 B-2C4435 B-1C4436 B-1C4437 B-1C4438 B-1
* C4501 D-5* C4502 D-5* C4503 D-5* C4504 D-5* C4505 D-5* C4506 D-5* C4507 E-5* C4508 D-5* C4509 E-5* C4510 D-5* C4511 E-5* C4512 D-5* C4513 E-5* C4514 D-5* C4515 D-5* C4516 E-5* C4517 D-6* C4518 D-6* C4519 D-6* C4520 D-6* C4521 C-6* C4522 D-6* C4523 C-6* C4524 A-5* C4525 A-6* C4526 C-6* C4527 D-7* C4528 D-6
C4529 E-5* C4530 D-7* C4531 D-6* C4532 D-6* C4533 B-5
C4534 E-6C4535 E-6
* C4536 B-5C4538 E-5
* C4539 B-5* C4540 C-5* C4541 B-5
C4543 D-5* C4544 C-6
* C4545 C-6C4546 D-5C4547 B-5C4548 B-5C4549 A-5C4550 B-5C4551 D-5
* C4553 C-5C4554 D-5C4555 D-5
* C4556 B-5* C4557 C-5* C4559 B-5
C4601 A-6C4602 B-6
* C4603 B-6C4604 C-6
* C4605 B-6* C4606 B-6* C4607 E-3* C4608 E-3
CN4001 E-3* CN4002 A-3* CN4003 B-1
CN4004 B-4CN4201 E-4CN4601 B-6
D4001 D-2D4003 D-2D4004 D-3D4005 D-3D4006 D-2
* D4201 D-3* D4401 A-1
D4501 E-6D4502 E-6D4503 E-6
* D4504 C-6D4601 A-6D4602 A-6
F4601 B-6F4602 B-6F4603 B-6F4604 B-6F4605 B-6F4606 B-6
* FB4101 B-3* FB4201 E-4* FB4202 D-4
FB4301 C-4
* IC4101 C-3* IC4201 D-3* IC4202 D-4
IC4301 C-3IC4401 B-2
* IC4501 D-5* IC4505 C-5
* L4101 B-3* L4102 C-3* L4201 E-4
L4202 D-4L4301 C-4
* L4401 B-2L4501 D-7L4502 D-6L4503 C-6L4504 D-7L4505 D-6L4506 D-6
* L4507 B-5* L4508 B-5* L4509 B-5
* L4510 B-5* L4511 C-6* L4512 C-6
L4513 B-5L4514 B-5L4515 B-5L4516 B-5L4517 D-5
* L4519 C-5* L4520 C-5* L4522 C-5* L4601 C-6
LF4601 B-6
Q4001 A-1* Q4003 A-1* Q4101 C-4* Q4102 C-4* Q4103 C-4
Q4301 D-4Q4302 C-3Q4303 C-3Q4304 C-3Q4305 D-3
* Q4306 B-3* Q4307 B-2* Q4501 D-6* Q4502 A-6* Q4503 D-7* Q4504 B-6* Q4505 D-6* Q4506 D-7* Q4507 B-5* Q4508 C-6* Q4509 D-7* Q4510 D-7* Q4511 D-7* Q4512 D-6
Q4513 E-5Q4514 D-5Q4515 E-5Q4516 E-5Q4517 D-5Q4518 D-5Q4519 D-5Q4520 D-5Q4521 D-5
* Q4601 B-6* Q4602 B-6* Q4603 B-6* Q4604 A-6* Q4605 E-3* Q4606 E-2* Q4607 E-2* Q4608 E-2* Q4609 E-2* Q4610 E-3* Q4611 E-4
R4001 D-2R4002 D-2R4003 D-3R4004 D-3R4005 D-3R4009 A-1
* R4010 A-1R4011 B-1R4012 B-1R4013 A-1
* R4101 C-4* R4102 C-4* R4103 C-4* R4104 C-4* R4105 C-4* R4106 C-4* R4107 C-4* R4108 B-4
C4001 D-2* C4002 E-3
C4003 E-3* C4101 C-4* C4102 C-4* C4103 C-4* C4104 C-4* C4105 C-4* C4106 C-4* C4107 B-4* C4108 C-4* C4109 C-4* C4110 C-4* C4111 B-3* C4112 B-4* C4113 B-3* C4114 C-3* C4115 B-3* C4116 B-3* C4117 C-3* C4118 B-3* C4119 B-3* C4120 C-3* C4121 C-3* C4122 C-3* C4123 C-3* C4124 C-3* C4125 C-3* C4201 E-4* C4202 D-3* C4203 E-2
C4204 D-3C4205 D-3C4206 D-3
* C4207 D-3* C4208 E-4
C4209 D-3C4210 D-3
* C4211 E-4* C4212 D-3* C4213 D-2* C4214 D-3* C4215 D-2* C4216 D-2* C4217 D-3* C4218 D-3* C4219 D-3* C4223 E-4
C4301 C-4C4302 C-4C4303 C-4C4304 C-4C4305 B-4C4306 C-4C4307 C-4C4308 C-4C4309 C-4C4310 C-4C4311 D-4C4312 C-3C4313 C-3C4314 C-3C4315 B-3C4316 D-3C4317 B-3C4318 C-3
* C4319 B-2C4320 B-3C4321 B-3C4322 D-4C4323 C-3C4324 C-3C4325 B-3C4326 B-3
* C4327 B-2* C4328 B-3
C4401 A-1C4402 B-1
CK-108/VA-117
no mark : side A* mark : side B
4-3. PRINTED WIRING BOARDS4-3. PRINTED WIRING BOARDS
CK-108 BOARD
* BT5201 C-3
C5201 B-5C5202 B-5
* C5203 A-2
* CN5201 C-7* CN5202 A-5* CN5203 A-2
CN5204 B-2* CN5205 B-4* CN5207 C-8
* D5201 A-7* D5203 B-7* D5204 B-7* D5205 A-4* D5206 C-8
D5207 B-5D5208 C-5
R5201 A-5* R5206 B-7* R5207 B-7* R5208 B-7
R5209 A-5* R5210 B-7* R5211 B-7* R5212 B-7
R5213 A-5* R5214 B-7* R5215 B-7* R5216 B-7
R5217 A-6* R5218 B-7* R5219 B-7
R5220 A-7* R5221 C-7* R5222 B-7
R5223 A-7* R5224 C-7* R5225 C-7* R5226 C-8* R5227 A-2* R5228 A-2
S5201 A-4S5202 A-5S5203 B-5S5204 A-6S5205 A-7S5206 A-8S5207 C-1
Mounted parts location of the VC-280 board is not shown.Pages from 4-95 to 4-96 are not shown.
5-2
DCR-TRV16/TRV16E/TRV18/TRV18E/TRV116E/TRV118E
Len
s de
vice
Mec
hani
sm d
eck
Not
e1
LC
D b
lock
LC
D90
1 (L
CD
pan
el)
LC
D b
lock
ND
901
(Flu
ores
cent
tube
)
EV
F bl
ock
LC
D90
3 (L
CD
pan
el)
Mec
hani
sm d
eck
M90
1 (D
rum
ass
y) N
ote1
Mec
hani
sm d
eck
M90
2 (C
apst
an m
otor
)
JK-2
17 b
oard
SE53
01/5
302
(YA
W/P
ITC
H s
enso
r)N
ote2
PD-1
61 b
oard
IC55
01 (
RG
B d
rive
r (L
CD
))
PD-1
61 b
oard
IC55
02 (
Tim
ing
gene
rato
r (L
CD
))
LB
-077
boa
rdIC
6101
,D61
02 (
Bac
k lig
ht (
EV
F))
VA
-117
boa
rdIC
4201
(R
GB
dri
ver
(EV
F))
VA
-117
boa
rdIC
4202
(T
imin
g ge
nera
tor
(EV
F))
VA
-117
boa
rdIC
4101
(V
ideo
IN
/OU
T)
CD
-365
boa
rdIC
8001
(C
CD
imag
e)
VC
-280
boa
rdIC
1402
, X14
01 (
Tim
ing
gene
rato
r)
VC
-280
boa
rdIC
1403
(S/
H, A
/D c
onv.
)
VC
-280
boa
rdIC
2101
(D
V s
igna
l pro
cess
)
VC
-280
boa
rdIC
1901
(E
Q, A
/D C
ON
V.,
PLL
)
VC
-280
boa
rdIC
1902
(R
EC
/PB
AM
P)
VC
-280
boa
rdIC
1801
(E
VR
)
Replaced parts
Block replacement Parts replacement
z z
z z
z z
z z
z z
z z
z z
z z
z z
z
z z
z z z
z z
z
z z
z
z
z z z
z z
z z
z z z z
z z z z
z z z z
z
z z
z z
z z z
1. Adjusting items when replacing main parts and boards.• Adjusting items when replacing main partsWhen replacing main parts, adjust the items indicated by z in the following table.Note1: When replacing the drum assy. or the mechanism deck, reset the data of page: 7, address: A7 to A9 to “00”. (Refer to “Record of Use check” of “5-
4. SERVICE MODE”)
Adjustment
Section
Initialization of
8, A, B,C, D,
E, F, 1B, 1F
page data
Camera
Color EVF
LCD
System control
Servo, RF
Video
Mechanism
Adjustment
Initialization of A, D page data
Initialization of B, 1B page data
Initialization of 8, C page data
Initialization of E, F, 1F page data
36MHz origin oscillation adj.
HALL adj.
Flange back adj.
Optical axis adj.
Color reproduction adj.
MAX GAIN adj.
AWB & LV standard data input
Auto white balance adj.
Mechanical shutter adj.
VCO adj.
RGB AMP adj.
Contrast adj.
White balance adj.
VCO adj.
RGB AMP adj.
Contrast adj.
COM AMP adj.
V COM adj.
White balance adj.
Serial No. input
CAP FG duty adj.
Switching position adj.
AGC center level adj.
APC & AEQ adj.
PLL fo & LPF fo adj.
Chroma BPF fo adj.
S VIDEO OUT Y level adj.
S VIDEO OUT chroma level adj.
Tape path adj.
Table. 5-1-1 (1).
5-3
DCR-TRV16/TRV16E/TRV18/TRV18E/TRV116E/TRV118E
LB
-077
boa
rd(C
OM
PLE
TE
)
PD-1
61 b
oard
(CO
MPL
ET
E)
VA
-117
boa
rd(C
OM
PLE
TE
)
VC
-280
boa
rd(C
OM
PLE
TE
)
VC
-280
boa
rdIC
2502
(E
EPR
OM
)
VC
-280
boa
rdIC
2901
(E
EPR
OM
)
Supp
ortin
g
Board EEPROM
replacement replacement
z z
z z
z z
z z
z z
z z z
z z z
z z
z z
z z z
z z z
z z z
z z z
z z z
z z z
z z z
z z z z
z z z
z z z
z z z
z z z
z z z
z z z
z z
z z z
z z z
z z z
z z z
z z z
z z z
z z z
z z z
Adjustment
Section
Initialization of
8, A, B,C, D,
E, F, 1B, 1F
page data
Camera
Color EVF
LCD
System control
Servo, RF
Video
Mechanism
Adjustment
Initialization of A, D page data
Initialization of B, 1B page data
Initialization of 8, C page data
Initialization of E, F, 1F page data
36MHz origin oscillation adj.
HALL adj.
Flange back adj.
Optical axis adj.
Color reproduction adj.
MAX GAIN adj.
AWB & LV standard data input
Auto white balance adj.
Mechanical shutter adj.
VCO adj.
RGB AMP adj.
Contrast adj.
White balance adj.
VCO adj.
RGB AMP adj.
Contrast adj.
COM AMP adj.
V COM adj.
White balance adj.
Serial No. input
CAP FG duty adj.
Switching position adj.
AGC center level adj.
APC & AEQ adj.
PLL fo & LPF fo adj.
Chroma BPF fo adj.
S VIDEO OUT Y level adj.
S VIDEO OUT chroma level adj.
Tape path adj.
Table. 5-1-1 (2).
• Adjusting items when replacing a board or EEPROMWhen replacing a board or EEPROM, adjust the items indicated by z in the following table.
Note2: There are two types of angular velocitysensor.
Type A: CG-L43A0Type B: CG-L43A1
Replace the broken sensor with a sametype sensor. If replace with other typeparts, the image will vibrate up and downor left and right during hand-shakecorrection operations.
5-4
DCR-TRV16/TRV16E/TRV18/TRV18E/TRV116E/TRV118E
Ref. No.
J-1
J-2
J-3
J-4
J-5
J-6
J-7
J-8
J-9
J-10
J-11
Name
Filter for color temperature correction (C14)
ND filter 1.0
ND filter 0.4
ND filter 0.1
Pattern box PTB-450
Color chart for pattern box
Adjustment remote commander(RM-95 upgraded) (Note)
Siemens star chart
Clear chart for pattern box
CPC-8 jig
Extension cable (100P, 0.5mm)
Mini pattern box
Camera table
Parts Code
J-6080-058-A
J-6080-808-A
J-6080-806-A
J-6080-807-A
J-6082-200-A
J-6020-250-A
J-6082-053-B
J-6080-875-A
J-6080-621-A
J-6082-388-A
J-6082-352-A
J-6082-353-B
J-6082-384-A
UsageAuto white balance adjustment/checkWhite balanceadjustment/check
White balance check
White balance check
White balance check
For checking the flange back
For adjusting the video sectionFor adjusting the color viewfinderFor adjusting the LCD block
For extension between the VA-117 board (CN4002) andthe VC-280 board (CN1007)
For adjusting the flange back
For adjusting the flange back
5-1. CAMERA SECTION ADJUSTMENT
1-1. PREPARATIONS BEFORE ADJUSTMENT (CAMERA SECTION)
1-1-1. List of Service Tools• Oscilloscope • Color monitor • Vectorscope• Regulated power supply • Digital voltmeter
Note: If the micro processor IC in the adjustment remote commander isnot the new micro processor (UPD7503G-C56-12), the pages cannotbe switched. In this case, replace with the new micro processor (8-759-148-35).
Fig. 5-1-1.
J-1 J-2
J-6
J-3
J-7 J-8
J-4 J-5
J-9 J-10
J-11
5-5
DCR-TRV16/TRV16E/TRV18/TRV18E/TRV116E/TRV118E
1-1-2. PreparationsNote1: For details of how remove the cabinet and boards, refer to “2.
DISASSEMBLY”.Note2: When performing only the adjustments, the lens block and boards
need not be disassembled.Note3: Before performing the adjustments, check the data of page: 0,
address: 10 is “00”. If not, set data: 00 to this address.
1) Connect the equipment for adjustments according to Fig. 5-1-3.
Note4: As removing the cabinet (R) assembly (removing CN1005 of theVC-280 board) means removing the lithium 3V power supply(BT5201 on the CK-108 board), data such as date, time, user-setmenus will be lost. After completing adjustments, reset these data.But the self-diagnosis data and the data on history of use (totaldrum rotation time etc.) will be kept even if the lithium 3V powersupply is removed. (Refer to “5-4.Service Mode” for the self-diagnosis data and the data on history of use.)
Note5: Setting the “Forced Camera Power ON” Mode1) Select page: 0, address: 01, and set data: 01.2) Select page: D, address: 10, set data: 01, and press the PAUSE
button.The above procedure will enable the camera power to be turnedon with the control switch block (PS-CX2670) removed. Aftercompleting adjustments, be sure to exit the “Forced Camera PowerON Mode”.
Note6: Exiting the “Forced Camera Power ON” Mode1) Select page: 0, address: 01, and set data: 01.2) Select page: D, address: 10, set data: 00, and press the PAUSE
button.3) Select page: 0, address: 01, and set data: 00.
Fig. 5-1-2.
1.5 m
Front of the lens
Pattern box
5-6
DCR-TRV16/TRV16E/TRV18/TRV18E/TRV116E/TRV118E
Fig. 5-1-3.
Color monitorVector scope
Terminated at 75Ω
VIDEO(Yellow)
AUDIO L(White)
AUDIO R(Red)
AC power adaptor
AC-L10,AC-VQ800 etc.
LANC jack
Lens block
Front panel block
VC-280board
VA-117 board
AUDIO/VIDEO jack
Adjustment remotecommander
EVF block
CPC-8 jig(J-6082-388-A)
Need not be connected.
CN1009
CN1010
CN1401
CN1006
CN1201
CN1901 CN1008
CN1005CN1007
CN4002
CN1002
CN1001
CN1011
CN4601CN4004
CN4003
CN4001
CN5202
CN5201
CN5207
CN5203
CN5205
CN4201Need not be connected.
CN5902MA-406 board
Must be connectedwhen performing the LCD system adjustments.
Must be connected.
DC IN jack
Must be connected when performing the EVF system adjustments.
Must be connected when performingthe video or EVF or LCD system adjustments.
CK-108 board
Cabinet (R)
Battery terminal
Extension cable (100P)(J-6082-352-A)
5-7
DCR-TRV16/TRV16E/TRV18/TRV18E/TRV116E/TRV118E
1-1-3. Precaution1. Setting the SwitchUnless otherwise specified, set the switches as follows and perform adjustments without loading cassette.
1. POWER switch (PS-CX2670 block) ..................... CAMERA2. NIGHT SHOT switch (Lens block) .................................OFF3. FOCUS switch (KP-CX2670 block) ..................... MANUAL4. BACK LIGHT switch (KP-CX2670 block) .....................OFF5. COLOR SLOW S/ SUPER NS switch (JK-218 board) ... OFF6. DEMO MODE (Menu setting) ........................................OFF7. STEADY SHOT (Menu setting) ...................................... OFF8. DIGITAL ZOOM (Menu setting) ....................................OFF
9. 16 : 9 WIDE (Menu setting) ............................................OFF10. PROGRAM AE (Menu setting) ................................... AUTO11. PICTURE EFECT (Menu setting) ...................................OFF12. DIGITAL EFECT (Menu setting) ....................................OFF13. WHITE BALANCE (Menu setting) ............................ AUTO14. AUTO SHUTTER (Menu setting) ...................................OFF15. DISPLAY (Menu setting) .................................. V-OUT/LCD16. DISPLAY (CK-108 board) ............................................... ON
2. Order of AdjustmentsBasically carry out adjustments in the order given.
Fig.5-1-4.
3. Subjects1) Color bar chart (Color reproduction adjustment frame)
When performing adjustments using the color bar chart, adjustthe picture frame as shown in Fig. 5-1-4. (Color reproductionadjustment frame)
2) Clear chart (Color reproduction adjustment frame)Remove the color bar chart from the pattern box and insert aclear chart in its place. (Do not perform zoom operations duringthis time.)
3) Flange back adjustment chartMake the chart shown in Fig. 5-1-5 using A0 size (1189mm ×841mm) black and white vellum paper.
H
A=B
C=D
A B B
C D
A
Enlargement
V
Electronic beam scanning frame
CRT picture frame
B A
Difference in level
Yello
wC
yan
Gre
enW
hite
Mag
enta
Red
Blu
e
Yello
wC
yan
Gre
enW
hite
Mag
enta
Red
Blu
e
Color bar chart (Color reproduction adjustment frame )
Fig. a(Video output terminal
output waveform)
Fig. b (TV monitor picture)
Adjust the camera zoom and direction toobtain the output waveform shown in Fig. aand the TV monitor display shown in Fig. b.
White
Black
841mm
1189mm
Fig. 5-1-5.
Note: Use matte vellum paper bigger than A0, and make sure the edges ofthe black and white paper joined together are not rough.
5-8
DCR-TRV16/TRV16E/TRV18/TRV18E/TRV116E/TRV118E
1-2. INITIALIZATION OF 8, A, B, C, D, E, F, 1B, 1FPAGE DATA
Note: When reading or writing the 1B or 1F page data, select page: 0,address: 10, and set data: 01, then select B or F page. The 1B or 1Fpage can be chosen by this data setting.After reading or writing, reset the data of page: 0, address: 10 to“00”.
[Connection of the power supply during the initialization of thedata.]1) Connect the regulated power supply and the digital voltmeter
to the battery terminal as shown in Fig. 5-1-6.2) Adjust the output voltage of the regulated power supply so that
the digital voltmeter display is 6.0 ± 0.1Vdc.3) Turn off the power supply.4) Turn on the HOLD switch of the adjusting remote commander.5) Turn on the power supply.6) Perform the initialization of the data.
Note: This is normal though the following message is indicated onthe LCD screen.
“FOR InfoLITHIUM BATTERY ONLY”
[Initialization Procedure]1. Initialization of A, D page data2. Initialization of B, 1B page data3. Initialization of 8, C page data4. Initialization of E, F, 1F page data
Fig.5-1-6.
Battery terminal
Regulated power supply
Digital volt meter
5-9
DCR-TRV16/TRV16E/TRV18/TRV18E/TRV116E/TRV118E
1-2-1. INITIALIZATION OF A, D PAGE DATA
Note: The data of page: 0, address: 10 must be “00”.
1. Initializing the A, D Page Data
Note1: If the A, D page data has been initialized, the following adjustmentsneed to be performed again.1) Modification of A, D page data
Note2: The power supply voltage must be 6.0 ± 0.1Vdc.
Adjusting page A
Adjusting Address 10 to FF
Adjusting page D
Adjusting Address 10 to 67
Initializing Method:
Order Page Address Data Procedure
1 0 01 01 Set the data.
2 0 10 00 Set the data.
3 7 03 Set the following data.02 (DCR-TRV16 (NTSC))03 (DCR-TRV18 (NTSC))82 (DCR-TRV16E /TRV116E(PAL))83 (DCR-TRV18E/TRV118E (PAL))
4 7 00 Set the following data.20 (Initializing A page)22 (Initializing D page)28 (Initializing A and D pages)
5 7 01 Set the following data, and pressPAUSE button.20 (Initializing A page)22 (Initializing D page)28 (Initializing A and D pages)
6 7 02 Check that the data changes to“01”
7 Perform “Modification of A, DPage Data”.
2. Modification of A, D Page DataIf the A, D page data has been initialized, change the data of the“Fixed data-2” address shown in the following tables by manualinput.
Modifying Method:1) Before changing the data, select page: 0, address: 01, and set
data: 01.2) New data for changing are not shown in the tables because
they are different in destination. When changing the data, copythe data built in the same model.Note: If copy the data built in the different model, the camcorder may
not operate.3) When changing the data, press the PAUSE button of the
adjustment remote commander each time when setting newdata to write the data in the non-volatile memory.
Processing after Completing Modification of A, D Page data
Order Page Address Data Procedure
1 2 00 29 Set the data.
2 2 01 29 Set the data, and press PAUSEbutton.
Note: If the following symptoms occur after completing of the“Modification of A, D page data”, check that the data of the “Fixeddata-2” addresses of A and D page are same as those of the samemodel of the same destination.1) The self-diagnosis code “E:20:00” on the LCD screen is displayed.2) The power is shut off so that unit cannot operate.
3. A Page Table
Note1: The data of page: 0, address: 10 must be “00”.Note2: Fixed data-1: Initialized data. (Refer to “1. Initializing the A, D
Page Data”.)Fixed data-2: Modified data. (Refer to “2. Modification of A, DPage Data”).
Table. 5-1-2.
Address00 to 0F
10 to 17
18
19
1A
1B to 2E
2F
30 to 31
32
33
34 to 51
52
53 to 59
5A
5B to CF
D0
D1
D2 to FF
Remark
Fixed data-1
Fixed data-2
Fixed data-1
Fixed data-2
Fixed data-1
Fixed data-2
Fixed data-1
Fixed data-2
Fixed data-1
Fixed data-2
Fixed data-1
Fixed data-2
Fixed data-1
Fixed data-2
Fixed data-1
Ver 1.1 2002. 06
5-10
DCR-TRV16/TRV16E/TRV18/TRV18E/TRV116E/TRV118E
4. D Page Table
Note1: The data of page: 0, address: 10 must be “00”.Note2: Fixed data-1: Initialized data. (Refer to “1. Initializing the A, D
Page Data”.)Fixed data-2: Modified data. (Refer to “2. Modification of A, DPage Data”).
Table. 5-1-3.
00 to 0F
10
11 to 12
13
14 to 15
16
17 to 21
22
23
24
25
26
27 to 29
2A
2B
2C
2D
2E to 36
37
38
39
3A
3B to 56
57
58
59
5A
5B
5C
5D
5E
5F to 67
00 Test mode
Fixed data-1
Fixed data-2
Fixed data-1
Fixed data-2
Fixed data-1
Fixed data-2
(Modified data. Copy the data
built in the same model.)
Fixed data-1
Fixed data-2
Fixed data-1
Fixed data-2
Fixed data-1
Fixed data-2
Fixed data-1
Fixed data-2
Fixed data-1
Fixed data-2
Fixed data-1
Fixed data-2
(Modified data. Copy the data
built in the same model.)
Fixed data-1
Address RemarkInitial value
5-11
DCR-TRV16/TRV16E/TRV18/TRV18E/TRV116E/TRV118E
1-2-2. INITIALIZATION OF B, 1B PAGE DATA
Note: When reading or writing the B page data, select page: 0, address:10, and set data: 00.When reading or writing the 1B page data, select page: 0, address:10, and set data: 01, then select B page. The 1B page can be chosenby this data setting.After reading or writing, reset the data of page: 0, address: 10 to“00”.
1. Initializing the B, 1B Page DataNote1: If “Initializing the B, 1B Page Data” is performed, all data
of the B page and 1B page will be initialized. (It isimpossible to initialize a single page.)
Note2: If the B, 1B page data has been initialized, the followingadjustments need to be performed again.1) Modification of B, 1B page data
Note3: The power supply voltage must be 6.0 ± 0.1Vdc.
Adjusting page B
Adjusting Address 00 to FF
Adjusting page 1B
Adjusting Address 00 to FF
Initializing Method:
Order Page Address Data Procedure
1 0 01 01 Set the data.
2 0 10 00 Set the data.
3 5 02 FF Set the data.
4 5 01 F3 Set the data, and press PAUSEbutton.
5 5 00 01 Set the data, and press PAUSEbutton.
6 5 02 Check that the data changes to“00”.
7 Perform “Modification of B, 1BPage Data”.
2. Modification of B, 1B Page DataIf the B, 1B page data has been initialized, change the data of the“Fixed data-2” address shown in the following tables by manualinput.
Modifying Method:1) Before changing the data, select page: 0, address: 01, and set
data: 01.2) When changing the B page data, select page: 0, address: 10,
and set data: 00.3) When changing the 1B page data, select page: 0, address: 10,
and set data: 01.After completing the modification of 1B page data, reset thedata of this address to “00”.
4) New data for changing are not shown in the tables becausethey are different in destination. When changing the data, copythe data built in the same model.Note: If copy the data built in the different model, the camcorder may
not operate.5) When changing the data, press the PAUSE button of the
adjustment remote commander each time when setting newdata to write the data in the non-volatile memory.
Processing after Completing Modification of B, 1B Page data:
Order Page Address Data Procedure
1 0 10 00 Set the data.
2 2 00 29 Set the data.
3 2 01 29 Set the data, and press PAUSEbutton.
3. B Page TableNote1: The data of page: 0, address: 10 must be “00”.Note2: Fixed data-1: Initialized data. (Refer to “1. Initializing the B, 1B
Page Data”.)Fixed data-2: Modified data. (Refer to “2. Modification of B, 1BPage Data”).
Table. 5-1-4.
4. 1B Page TableNote1: When reading or writing the 1B page data, select page: 0, address:
10, and set data: 01, then select B page. The 1B page can be chosenby this data setting.After reading or writing, reset the data of page: 0, address: 10 to“00”.
Note2: Fixed data-1: Initialized data. (Refer to “1. Initializing the B, 1BPage Data”.)Fixed data-2: Modified data. (Refer to “2. Modification of B, 1BPage Data”).
Address00 to 01
02
03 to 16
17
18 to FF
RemarkFixed data-1
Fixed data-2
Fixed data-1
Fixed data-2
Fixed data-1
Table. 5-1-5.
Address00 to E0
E1
E2 to FF
RemarkFixed data-1
Fixed data-2
Fixed data-1
5-12
DCR-TRV16/TRV16E/TRV18/TRV18E/TRV116E/TRV118E
1-2-3. INITIALIZATION OF 8, C PAGE DATANote: The data of page: 0, address: 10 must be “00”.
1. Initializing the 8, C Page Data
Note1: If “Initializing the 8, C Page Data” is performed, all dataof the 8 page and C page will be initialized. (It isimpossible to initialize a single page.)
Note2: If the 8, C page data has been initialized, following adjustmentsneed to be performed again.1) Modification of 8, C page data2) Serial No. input3) Viewfinder system adjustments4) LCD system adjustments5) Servo and RF system adjustments6) Video system adjustments
Note3: The power supply voltage must be 6.0 ± 0.1Vdc.
Adjusting page 8
Adjusting Address 00 to A3
Adjusting page C
Adjusting Address 10 to FF
Initializing Method:
Order Page Address Data Procedure
1 0 01 01 Set the data.
2 0 10 00 Set the data.
3 3 81 Check that the data is “00”.
4 3 80 0C Set the data, and press PAUSEbutton.
5 3 80 Check that the data changes to“1C”.
6 Perform “Modification of 8, CPage Data”.
2. Modification of 8, C Page DataIf the 8, C page data has been initialized, change the data of the“Fixed data-2” address shown in the following table by manual input.
Modifying Method:1) Before changing the data, select page: 0, address: 01, and set
data: 01.2) New data for changing are not shown in the tables because
they are different in destination. When changing the data, copythe data built in the same model.Note: If copy the data built in the different model, the camcorder may
not operate.3) When changing the data, press the PAUSE button of the
adjustment remote commander each time when setting newdata to write the data in the non-volatile memory.
4) Check that the data of adjustment addresses is the initial value.If not, change the data to the initial value.
Processing after Completing Modification of 8, C Page data
Order Page Address Data Procedure
1 2 00 29 Set the data.
2 2 01 29 Set the data, and press PAUSEbutton.
3. 8 Page Table
Note1: The data of page: 0, address: 10 must be “00”.Note2: Fixed data-1: Initialized data. (Refer to “1. Initializing the 8, C
Page Data”.)Fixed data-2: Modified data. (Refer to “2. Modification of 8, CPage Data”).
Table. 5-1-6.
Address RemarkInitial value
Address RemarkInitial value
00 to 18
19
1A to 28
29
2A to 2E
2F
30 to 3A
3B
3C to 49
4A
4B to 51
52
53 to 59
5A
5B to 79
7A
7B
7C
7D
7E
7F
80
81
82
83
84
85 to 89
8A
8B
8C
8D
8E
8F
90
91
92
93
94 to A3
08
00
46
01
02
00
00
00
Fixed data-1
Fixed data-2
Fixed data-1
Fixed data-2
Fixed data-1
Fixed data-2
Fixed data-1
Fixed data-2
Fixed data-1
Fixed data-2
Fixed data-1
Fixed data-2
Fixed data-1
Fixed data-2
Fixed data-1
Fixed data-2
(Modified data. Copy the data
built in the same model.)
Fixed data-1
Fixed data-2
Fixed data-1
Serial No. input
Fixed data-1
5-13
DCR-TRV16/TRV16E/TRV18/TRV18E/TRV116E/TRV118E
4. C Page TableNote1: The data of page: 0, address: 10 must be “00”.Note2: Fixed data-1: Initialized data. (Refer to “1. Initializing the 8, C
Page Data”.)Fixed data-2: Modified data. (Refer to “2. Modification of 8, CPage Data”).
Address RemarkInitial value
Address RemarkInitial value
00 to 0F
10
11
12
13
14 to 15
16
17
18
19
1A
1B
1C
1D
1E
1F
20
21
22
23 to 24
25
26
27
28
29
2A to 2B
2C
2D to 34
35
36
37 to 4E
4F
50
51
52
53
54
55
56
57
58
59 to 5E
5F
60
61
62
63
64
65
66
67
68
69
6A
6B
6C
6D to 71
72
73 to 75
76
77 to 79
7A
7B to 81
82
83 to 88
89
8A
8B
8C
8D to A9
AA
AB
AC
AD
AE
AF
B0 to C0
C1
C2
C3
C4
C5
C6
C7 to C8
C9
CA
CB
CC
CD
CE
CF to D0
D1
D2
D3
D4
D5
D6
D7
D8
D9
DA
DB
DC
DD
Address RemarkInitial value
Address RemarkInitial value
EE
00
00
00
E0
2A
2A
32
32
25
3E
3E
DC
99
88
E3
A1
04
20
03
87
6F
97
80
80
37
80
70
80
30
C0
80
80
50
Switching position adj.
Fixed data-1
CAP FG duty adj.
Fixed data-1
AEQ adj.
Fixed data-1
AEQ adj.
Fixed data-1
AGC center level adj.
PLL fo adj.
APC adj.
LPF fo adj.
Fixed data-1
S VIDEO out Y level adj.
S VIDEO out Cr level adj.
S VIDEO out Cb level adj.
Chroma BPF fo adj.
PLL fo adj.
Fixed data-1
APC adj.
Fixed data-1
Fixed data-2
Fixed data-1
Fixed data-2
VCO adj. (EVF)
Fixed data-2
RGB AMP adj. (EVF)
Fixed data-1
White balance adj. (EVF)
Contrast adj. (EVF)
Fixed data-1
Fixed data-2
Fixed data-1
VCO adj. (LCD)
V COM adj. (LCD)
RGB AMP adj. (LCD)
Fixed data-1
COM AMP adj. (LCD)
White balance adj. (LCD)
Contrast adj. (LCD)
Fixed data-1
Fixed data-2
Fixed data-1
Fixed data-2
Fixed data-1
Fixed data-2
Fixed data-1
Fixed data-2
Fixed data-1
Fixed data-2
Fixed data-1
Fixed data-2
Fixed data-1
Fixed data-2
Fixed data-2
Fixed data-1
Fixed data-2
(Modified data. Copy the data
built in the same model.)
Fixed data-1
Fixed data-2
Fixed data-1
Fixed data-2
(Modified data. Copy the data
built in the same model.)
Fixed data-1
Fixed data-2
(Modified data. Copy the data
built in the same model.)
Fixed data-1
Fixed data-2
Fixed data-1
Fixed data-2
Fixed data-1
Fixed data-2
Fixed data-1
Fixed data-2
(Modified data. Copy the data
built in the same model.)
5-14
DCR-TRV16/TRV16E/TRV18/TRV18E/TRV116E/TRV118E
Table. 5-1-7.
Address RemarkInitial value
DE
DF
E0
E1
E2
E3
E4 to E7
E8
E9
EA
EB
EC
ED
EE
EF
F0 to F1
F2
F3
F4
F5
F6
F7
F8
F9
FA
FB
FC
FD
FE
FF
00
00
00
00
00
00
00
00
00
00
00
00
Fixed data-2
(Modified data. Copy the data
built in the same model.)
Fixed data-1
Fixed data-2
Fixed data-1
Fixed data-2
(Modified data. Copy the data
built in the same model.)
Fixed data-1
Fixed data-2
Fixed data-1
Emergency memory address
C page
5-15
DCR-TRV16/TRV16E/TRV18/TRV18E/TRV116E/TRV118E
1-2-4. INITIALIZATION OF E, F, 1F PAGE DATANote: When reading or writing the E, F page data, select page: 0, address:
10, and set data: 00.When reading or writing the 1F page data, select page: 0, address:10, and set data: 01, then select F page. The 1F page can be chosenby this data setting.After reading or writing, reset the data of page: 0, address: 10 to“00”.
1. Initializing the E, F, 1F Page Data
Note1: If “Initializing the E, F, 1F Page Data” is performed, alldata of the E page, F page and 1F page will be initialized.(It is impossible to initialize a single page.)
Note2: If the E, F, 1F page data has been initialized, following adjustmentsneed to be performed again.1) Modification of E, F, 1F page data2) 36MHz origin osc. adjustment3) Camera system adjustments
Note3: The power supply voltage must be 6.0 ± 0.1Vdc.Note4: NTSC model: DCR-TRV16/TRV18
PAL model: DCR-TRV16E/TRV18E/TRV116E/TRV118E
Adjusting page E
Adjusting Address 00 to FF
Adjusting page F
Adjusting Address 10 to FF
Adjusting page 1F
Adjusting Address 00 to D9
Initializing Method:
Order Page Address Data Procedure
1 0 01 01 Set the data.
2 0 10 00 Set the data.
3 6 01 Set the following data, and pressPAUSE button.2D (NTSC), 2F (PAL)
4 6 03 FF Set the data, and press PAUSEbutton.
5 6 02 Check that the data changes to“01”.
6 Perform “Modification of E, F,1F Page Data”.
2. Modification of E, F, 1F Page DataIf the E, F, 1F page data has been initialized, change the data of the“Fixed data-2” address shown in the following table by manual input.
Modifying Method:1) Before changing the data, select page: 0, address: 01, and set
data: 01.2) When changing the E, F page data, select page: 0, address: 10,
and set data: 00.3) When changing the 1F page data, select page: 0, address: 10,
and set data: 01.After completing the modification of 1F page data, reset thedata of this address to “00”.
4) New data for changing are not shown in the tables becausethey are different in destination. When changing the data, copythe data built in the same model.Note: If copy the data built in the different model, the camcorder may
not operate.5) When changing the data, press the PAUSE button of the
adjustment remote commander each time when setting newdata to write the data in the non-volatile memory.
6) Check that the data of adjustment addresses is the initial value.If not, change the data to the initial value.
Processing after Completing Modification of E, F, 1F Page data
Order Page Address Data Procedure
1 0 10 00 Set the data.
2 2 00 29 Set the data.
3 2 01 29 Set the data, and press PAUSEbutton.
4 Perform “36MHz Origin Osc.Adjustment” of the camerasystem adjustment.
5-16
DCR-TRV16/TRV16E/TRV18/TRV18E/TRV116E/TRV118E
3. E Page Table
Note1: The data of page: 0, address: 10 must be “00”.Note2: Fixed data-1: Initialized data. (Refer to “1. Initializing the E, F, 1F
Page Data”.)Fixed data-2: Modified data. (Refer to “2. Modification of E, F,1F Page Data”).
Table. 5-1-8.
Address00 to 10
11
12 to 14
15
16
17
18 to 1B
1C
1D
1E to 36
37
38 to 3C
3D
3E to 6E
6F
70 to 94
95
96 to 97
98
99
9A
9B
9C
9D
9E
9F
A0
A1
A2 to AD
AE
AF to C1
C2
C3 to E8
E9
EA
EB
EC
ED
EE
EF to FF
RemarkFixed data-1
Fixed data-2
Fixed data-1
Fixed data-2
Fixed data-1
Fixed data-2
Fixed data-1
Fixed data-2
Fixed data-1
Fixed data-2
Fixed data-1
Fixed data-2
Fixed data-1
Fixed data-2
Fixed data-1
Fixed data-2
Fixed data-1
Fixed data-2
Fixed data-1
Fixed data-2
(Modified data. Copy the data
built in the same model.)
Fixed data-1
Fixed data-2
Fixed data-1
Fixed data-2
Fixed data-1
Fixed data-2
(Modified data. Copy the data
built in the same model.)
Fixed data-1
Fixed data-2
Fixed data-1
4. F Page Table
Note1: The data of page: 0, address: 10 must be “00”.Note2: Fixed data-1: Initialized data. (Refer to “1. Initializing the E, F, 1F
Page Data”.)Fixed data-2: Modified data. (Refer to “2. Modification of E, F,1F Page Data”).
Address RemarkInitial valueInitial valueNTSC PAL
00 to 0F
10 to 11
12
13 to 16
17
18
19
1A to 1C
1D
1E
1F
20 to 29
2A
2B
2C
2D
2E
2F
30 to 32
33
34
35
36 to 39
3A
3B
3C to 45
46
47
48
49
4A
4B
4C
4D
4E
4F
50
51
52
53
54
55
56
57 to 5B
5C
5D
5E
5F to 65
80
81
5D
17
9A
80
7A
4D
3E
64
59
96
7A
22
27
00
F1
19
51
20
22
13
93
00
00
00
00
46
19
00
2A
00
00
00
00
80
81
5D
17
9A
80
7A
90
3E
43
59
80
40
22
24
00
EF
19
51
20
22
13
93
00
00
00
00
46
19
00
2A
00
00
00
00
Fixed data-1
36MHz origin osc. adj.
Fixed data-1
HALL adj.
Fixed data-1
MAX GAIN adj.
AWB & LV standard data input
Fixed data-1
AWB & LV standard data input
Auto white balance adj.
Fixed data-1
Color reproduction adj.
Fixed data-1
Color reproduction adj.
Fixed data-1
Color reproduction adj.
Fixed data-1
Flange back adj.
Fixed data-1
Fixed data-2
Optical axis adj.
Fixed data-1
5-17
DCR-TRV16/TRV16E/TRV18/TRV18E/TRV116E/TRV118E
80
80
80
80
80
80
40
00
34
00
30
00
2A
00
28
00
70
80
80
80
80
1E
80
80
80
80
80
80
40
00
34
00
30
00
2A
00
28
00
70
80
80
80
80
1E
66
67
68
69
6A
6B
6C
6D
6E
6F
70
71
72
73
74
75
76
77
78
79
7A
7B
7C to 92
93
94
95 to 9E
9F
A0 to C3
C4
C5 to C9
CA
CB
CC to D9
DA
DB to DD
DE
DF to E7
E8
E9
EA to EB
EC
ED to F4
F5
F6
F7
F8 to FF
Mechanical shutter adj.
Fixed data-1
Fixed data-2
Fixed data-1
Fixed data-2
Fixed data-1
Fixed data-2
Fixed data-1
Fixed data-2
Fixed data-1
Fixed data-2
Fixed data-1
Fixed data-2
Fixed data-1
Fixed data-2
Fixed data-1
Fixed data-2
Fixed data-1
Fixed data-2
Fixed data-1
Fixed data-2
Fixed data-1
Table. 5-1-9.
5. 1F Page Table
Note1: When reading or writing the 1F page data, select page: 0, address:10, and set data: 01, then select F page. The 1F page can be chosenby this data setting.After reading or writing, reset the data of page: 0, address: 10 to“00”.
Note2: Fixed data-1: Initialized data. (Refer to “1. Initializing the E, F, 1FPage Data”.)Fixed data-2: Modified data. (Refer to “2. Modification of E, F,1F Page Data”).
F page
00
01
02 to 05
06
07
08
09
0A to 51
52
53 to 56
57
58 to 59
5A
5B
5C
5D to 64
65
66 to 6B
6C
6D
6E
6F
70 to 73
74
75 to 77
78
79
7A to 7F
80
81 to 97
98
99
9A
9B
9C
9D
9E
9F
A0
A1
A2
A3
A4 to B0
B1
B2
B3
B4 to B9
Fixed data-2
Fixed data-1
Fixed data-2
(Modified data. Copy the data
built in the same model.)
Fixed data-1
Fixed data-2
Fixed data-1
Fixed data-2
Fixed data-1
Fixed data-2
(Modified data. Copy the data
built in the same model.)
Fixed data-1
Fixed data-2
Fixed data-1
Fixed data-2
(Modified data. Copy the data
built in the same model.)
Fixed data-1
Fixed data-2
Fixed data-1
Fixed data-2
Fixed data-1
Fixed data-2
Fixed data-1
Fixed data-2
(Modified data. Copy the data
built in the same model.)
Fixed data-1
Fixed data-2
Fixed data-1
Fixed data-2
Fixed data-1
Address RemarkInitial valueInitial valueNTSC PAL
Address Remark
5-18
DCR-TRV16/TRV16E/TRV18/TRV18E/TRV116E/TRV118E
Address Remark
BA
BB to CB
CC
CD
CE
CF
D0
D1 to D9
Fixed data-2
Fixed data-1
Fixed data-2
(Modified data. Copy the data
built in the same model.)
Fixed data-1
1F page
Table. 5-1-10.
5-19
DCR-TRV16/TRV16E/TRV18/TRV18E/TRV116E/TRV118E
1-3. CAMERA SYSTEM ADJUSTMENTSBefore perform the camera system adjustments (except for “36MHzOrigin Oscillation Adjustment”), check that the specified values of“VIDEO SYSTEM ADJUSTMENTS” are satisfied.And check that the data of page: 0, address: 10 is “00”. If not, setdata: 00 to this address.
1. 36MHz Origin Oscillation Adjustment (VC-280 board)Set the frequency of the clock for synchronization.If deviated, the synchronization will be disrupted and the color willbecome inconsistent.
Subject Not required
Measurement Point Pin qs of IC1402Or Pin eg of IC2401
Measuring Instrument Frequency counter
Adjustment Page F
Adjustment Address 12
Specified Value Pin qs of IC1402f=18000000 ± 90HzPin eg of IC2401f=13500000 ± 68Hz
Note1: The data of page: 0, address: 10 must be “00”.Note2: When open the VA-117 board, use the following extension cable
between the VC-280 board CN1007 and VA-117 board CN4002.J-6082-352-A (100P, 0.5mm)
Adjusting method:
Order Page Address Data Procedure
1 0 01 01 Set the data.
2 F 12 Change the data and set thefrequency (f) to the specifiedvalue.
3 F 12 Press PAUSE button.
4 0 01 00 Set the data.
2. HALL Adjustment
For detecting the position of the lens iris and ND filter, adjust AMPgain and offset.
Subject Not required
Measurement Point Display data of page 1 (Note1)
Measuring Instrument Adjustment remote commander
Adjustment Page F
Adjustment Address 17, 18, 19
Specified Value 1 15 to 19
Specified Value 2 8A to 8E
Note1: Displayed data of page 1 of the adjustment remote commander.1 : 00 : XX
IRIS display dataNote2: The data of page: 0, address: 10 must be “00”.
Switch setting:POWER ......................................................................... CAMERA
Adjusting method:
Order Page Address Data Procedure
1 0 01 01 Set the data.
2 6 94 17 Set the data.
3 6 95 8C Set the data.
4 6 01 6D Set the data, and press PAUSEbutton.
5 6 02 Check that the data changes to“01”. (Note3)
6 6 01 00 Set the data, and press PAUSEbutton.
Note3: The adjustment data will be automatically input to page: F, address:17, 18, 19.
Checking method:
Order Page Address Data Procedure
1 0 03 03 Set the data.
2 6 01 01 Set the data, and press PAUSEbutton.
3 1 Check that the IRIS display data(Note1) satisfies the specifiedvalue 1.
4 6 01 03 Set the data, and press PAUSEbutton.
5 1 Check that the IRIS display data(Note1) satisfies the specifiedvalue.2.
Processing after Completing Adjustments:
Order Page Address Data Procedure
1 6 94 00 Set the data.
2 6 95 00 Set the data.
3 6 01 00 Set the data, and press PAUSEbutton.
4 0 03 00 Set the data.
5 0 01 00 Set the data.
Fig. 5-1-7.
1
1213 24
48 3736
25IC1402
1
20
21 40
80 61
41
60
IC2401
VC-280 board (SIDE B)
VC-280 board (SIDE A)
5-20
DCR-TRV16/TRV16E/TRV18/TRV18E/TRV116E/TRV118E
3. Flange Back Adjustment (Using Minipattern Box)The inner focus lens flange back adjustment is carried outautomatically. In whichever case, the focus will be deviated duringauto focusing/manual focusing.
Subject Siemens star chart with ND filter forthe minipattern box (Note1)
Measuring Instrument Adjustment remote commander
Adjustment Page F
Adjustment Address 46 to 56
Note1: Dark Siemens star chart.Note2: This adjustment should be carried out upon completion of “HALL
Adjustment”.Note3: Make the lens horizontal and perform this adjustment.Note4: The data of page: 0, address: 10 must be “00”.Note5: Check that the data of page: 6, address: 02 is “00”. If not, to page:
6, address: 01, set data: 00, and press the PAUSE button.
Switch setting:1) POWER .................................................................. CAMERA2) NIGHT SHOT ..................................................................OFF
Preparations:1) The minipattern box is installed as shown in the following
figure.Note: The attachment lenses are not used.
2) Install the minipattern box so that the distance between it andthe front of the lens of the camcorder is less than 3cm.
3) Make the height of the minipattern box and the camcorder equal.4) Check that the output voltage of the regulated power supply is
the specified voltage.5) Check that at both the zoom lens TELE end and WIDE end,
the center of the Siemens star chart and center of the exposurescreen coincide.
Specified voltage:The specified voltage varies according to the minipattern box, soadjust the power supply output voltage to the specified voltagewritten on the sheet which is supplied with the minipattern box.
Adjusting method:
Order Page Address Data Procedure
1 0 01 01 Set the data.
2 6 48 01 Set the data.
3 6 01 13 Set the data, and press PAUSEbutton. (Note3)
4 6 01 27 Set the data, and press PAUSEbutton.
5 6 02 Check that the data changes to“01”. (Note6)
Note6: The adjustment data will be automatically input to page: F, address:46 to 56.
Processing after Completing Adjustments:
Order Page Address Data Procedure
1 6 48 00 Set the data.
2 0 01 00 Set the data.
3 Turn off the power and turn onagain.
4 Perform “Flange Back Check”.
Fig. 5-1-8.
Minipattern box
Below 3 cm
Camcorder
Camera table
Red (+)
Black (–)
Yellow (SENS +)
White (SENS –)
Black (GND)
Need not connected
Regulated power supplyOutput voltage : Specified voltage ±0.01Vdc
Output current : more than 3.5A
5-21
DCR-TRV16/TRV16E/TRV18/TRV18E/TRV116E/TRV118E
4. Flange Back Adjustment(Using Flange Back Adjustment Chart and SubjectMore Than 500m Away)
The inner focus lens flange back adjustment is carried outautomatically. In whichever case, the focus will be deviated duringauto focusing/manual focusing.
4-1. Flange Back Adjustment (1)
Subject Flange back adjustment chart(2.0 m from the front of the protectionglass)(Luminance: 350 ± 50 lux)
Measuring Instrument Adjustment remote commander
Adjustment Page F
Adjustment Address 46 to 56
Note1: This adjustment should be carried out upon completion of “HALLAdjustment”.
Note2: Make the lens horizontal and perform this adjustment.Note3: The data of page: 0, address: 10 must be “00”.Note4: Check that the data of page: 6, address: 02 is “00”. If not, to page:
6, address: 01, set data: 00, and press the PAUSE button.
Switch setting:1) POWER .................................................................. CAMERA2) NIGHT SHOT .................................................................. OFF
Preparations:1) Check that at both the zoom lens TELE end and WIDE end,
the center of the chart for the flange back adjustment and centerof the exposure screen coincide.
Adjusting method:
Order Page Address Data Procedure
1 0 01 01 Set the data.
2 6 48 01 Set the data.
3 6 01 13 Set the data, and press PAUSEbutton. (Note2)
4 6 01 15 Set the data, and press PAUSEbutton.
5 6 02 Check that the data changes to“01”. (Note5)
Note5: The adjustment data will be automatically input to page: F, address:46 to 56.
Processing after Completing Adjustments:
Order Page Address Data Procedure
1 Turn off the power and turn onagain.
2 Perform “Flange BackAdjustment (2)”
4-2. Flange Back Adjustment (2)Perform this adjustment after performing “Flange Back Adjustment(1)”.
Subject Subject more than 500m away(Subjects with clear contrast such asbuildings, etc.)
Measurement Point Check operation on TV monitor
Measuring Instrument
Adjustment Page F
Adjustment Address 46 to 56
Note1: Make the lens horizontal and perform this adjustment.Note2: The data of page: 0, address: 10 must be “00”.Note3: Check that the data of page: 6, address: 02 is “00”. If not, to page:
6, address: 01, set data: 00, and press the PAUSE button.
Switch setting:1) POWER .................................................................. CAMERA2) NIGHT SHOT .................................................................. OFF
Preparations:1) Set the zoom lens to the TELE end and expose a subject that is
more than 500m away (subject with clear contrast such asbuilding, etc.). (Nearby subjects less than 500m away shouldnot be in the screen.)
Adjusting method:
Order Page Address Data Procedure
1 0 01 01 Set the data.
2 6 48 01 Set the data.
3 6 01 13 Set the data, and press PAUSEbutton. (Note2)
4 Place a ND filter on the lens sothat the optimum image is obtain.
5 6 01 29 Set the data, and press PAUSEbutton.
6 6 02 Check that the data changes to“01”. (Note4)
Note4: The adjustment data will be automatically input to page: F, address:46 to 56.
Processing after Completing Adjustments:
Order Page Address Data Procedure
1 6 48 00 Set the data.
2 0 01 00 Set the data.
3 Turn off the power and turn onagain.
4 Perform “Flange Back Check”
5-22
DCR-TRV16/TRV16E/TRV18/TRV18E/TRV116E/TRV118E
5. Flange Back Check
Subject Siemens star(2.0 m from the front of the lens)(Luminance : approx. 200 lux)
Measurement Point Check operation on TV monitor
Measuring Instrument
Specified Value Focused at the TELE end and WIDEend.
Note1: The data of page: 0, address: 10 must be “00”.
Switch setting:1) POWER .................................................................. CAMERA2) NIGHT SHOT (Menu display) ........................................OFF
Note2: When the auto focus is ON, the lens can be checked if it is focusedor not by observing the data on the page 1 of the adjustment remotecommander.1) Select page: 0, address: 03, and set data: 0F.2) Page 1 shows the state of the focus.
1 : 00 : XXOdd: FocusedEven: Unfocused
Checking method:1) Select page: 6, address: 40, and set data: 01.2) Select page: 6, address: 41, and set data: 01.3) Place the Siemens star 2.0m from the front of the lens.4) To open the IRIS, decrease the luminous intensity to the
Siemens star up to a point before noise appear on the image.5) Shoot the Siemens star with the zoom TELE end.6) Turn on the auto focus.7) Check that the lens is focused (Note2).8) Select page: 6, address: 21, and set data: 10.9) Shoot the Siemens star with the zoom WIDE end.10) Observe the TV monitor and check that the lens is focused.
Processing after Completing Adjustments:1) Select page: 6, address: 21, and set data: 00.2) Select page: 6, address: 40, and set data: 00.3) Select page: 6, address: 41, and set data: 00.4) Select page: 0, address: 03, and set data: 00.
5-23
DCR-TRV16/TRV16E/TRV18/TRV18E/TRV116E/TRV118E
6. Optical Axis AdjustmentAlign the lens Optical Axis with that of the CCD imager. If deviated,center of picture can lose focus when zoom is operated from theWIDE end to the TELE end.
Subject Siemens star
Measurement Point Check on the monitor TV
Measuring Instrument
Adjustment Page F
Adjustment Address 5E
Note1: This adjustment should be carried out upon completion of “Flangeback adjustment”.
Note2: The data of page: 0, address: 10 must be “00”.Note3: Check that the data of page: 6, address: 48 is “00”. If not, set data:
00 to this address.
Switch setting:1) POWER .................................................................. CAMERA2) DIGITAL ZOOM (Menu display) ................................... OFF3) STEADY SHOT (Menu display) .....................................OFF
Preparations before adjustments:1) Playback the monoscope segment of the system check tape
(XH5-5 (NTSC), XH5-5P (PAL),).2) Attach the optical axis frame chart (transparent) on the monitor
TV screen. Center of monoscope image and that of optical axisframe must be agree.
3) Set to the camera mode.
Adjusting method:1) Select page: 0, address: 01, and set data: 01.2) Select page: F, address: 5E, set data: 00, and press the PAUSE
button.3) Place the Siemens star 2.0 m away from the front of the lens.4) Shoot the Siemens star with the zoom TELE end.5) Point the lens toward the Siemens star chart until center of the
Siemens star is located in the center of the optical axis frame.6) Shoot the Siemens star with the zoom WIDE end.7) Measure on the monitor TV screen in which area of the optical
axis frame the center of the Siemens star is located. Measurethe amount of displacement (distance between the center ofthe Siemens star and the center of the optical axis frame.) Themeasurement value is named L1.
8) Read the correction data corresponding to the area from Table5-1-11.
9) Input the correction data to page: F, address: 5E, and press thePAUSE button
10) Shoot the Siemens star with the zoom TELE end.11) Point the lens toward the Siemens star chart until center of the
Siemens star is located in the center of the optical axis frame.12) Shoot the Siemens star with the zoom WIDE end.13) Measure the amount of displacement (distance between the
center of the Siemens star and the center of the optical axisframe.) The measurement value is named L2.
14) Compare the values L1 and L2, and confirm that L2 is smallerthan L1. If L2 is lager than L1, select page: F, address: 5E, setdata: 00, and press the PAUSE button.
Table 5-1-11.
Processing after Completing Adjustments:1) Select page: 0, address: 01, and set data: 00.
Fig. 5-1-9.
Area
1
2
3
4
5
6
7
8
Correction data(Page: F, address: 5E)
01
02
03
04
05
06
07
08
Display phase
22.6° to 67.5°67.6° to 112.5°
112.6° to 157.5°157.6° to 202.5°202.6°to 247.5°247.6° to 292.5°292.6° to 337.5°337.6° to 22.5°
5-24
DCR-TRV16/TRV16E/TRV18/TRV18E/TRV116E/TRV118E
7. Picture Frame Setting
Subject Color bar chart(Color reproduction adjustment frame)(1.5m from the front of the lens)
Measurement Point Video output terminal
Measuring Instrument Oscilloscope and TV monitor
Specified Value A=B, C=D, E=F
Note1: The following adjustments should be carried out upon completionof “Flange back adjustment”.
Note2: The data of page: 0, address: 10 must be “00”.
Switch setting:1) POWER .................................................................. CAMERA2) NIGHT SHOT ..................................................................OFF3) DIGITAL ZOOM (Menu display) ...................................OFF4) STEADY SHOT (Menu display) .....................................OFF
Setting method:1) Select page: 6, address: 48, and set data: 01.2) Adjust the zoom and the camera direction, and set to the
specified position.3) Mark the position of the picture frame on the monitor display,
and adjust the picture frame to this position in followingadjustments using “Color reproduction adjustment frame”.
Processing after Completing Camera System Adjustments:After completing the camera system adjustments, release the datasettings.1) Select page: 6, address: 48, and set data: 00.
Check on the oscilloscope
1. Horizontal period
Fig. 5-1-10.
2. Vertical period
Fig. 5-1-11.
Check on the monitor TV (Underscanned mode)
Fig. 5-1-12.
A=B C=D
A
B C
D
E=F
V
E F
Color bar chart picture frame Monitor TV picture frame
5-25
DCR-TRV16/TRV16E/TRV18/TRV18E/TRV116E/TRV118E
8. Color Reproduction AdjustmentAdjust the color Separation matrix coefficient so that proper colorreproduction is produced.
Subject Color bar chart(Color reproduction adjustment frame)
Measurement Point Video output terminal
Measuring Instrument Vectorscope
Adjustment Page F
Adjustment Address 33, 35, 3A, 3B
Specified Value All color luminance points shouldsettle within each color reproductionframe.
Note1: The data of page: 0, address: 10 must be “00”.Note2: NTSC model: DCR-TRV16/TRV18
PAL model: DCR-TRV16E/TRV18E/TRV116E/TRV118E
Switch setting:1) POWER .................................................................. CAMERA2) NIGHT SHOT .................................................................. OFF3) DIGITAL ZOOM (Menu display) ................................... OFF4) STEADY SHOT (Menu display) .....................................OFF
Adjusting method:1) Select page: 0, address: 01, and set data: 01.2) Select page: 6, address: 48, and set data: 01.3) Select page: 6, address: 9D, and set data: 29.4) Select page: 6, address: 01, set data: 3D, and press the PAUSE
button.5) Select page: F, address: D0, set the following data, and press
the PAUSE button.37 (NTSC), B7 (PAL)
6) Adjust the GAIN and PHASE of the vectorscope, and adjustthe burst luminance point to the burst position of the colorreproduction frame.
7) Change the data of page: F, address: 33, 35, 3A and 3B, andsettle each color luminance point in each color reproductionframe.Note: Be sure to press the PAUSE button of the adjustment remote
commander before changing the addresses. If not, the new datawill not be written to the memory.
Processing after Completing Adjustments:1) Select page: 6, address: 01, set data: 00, and press the PAUSE
button.2) Select page: 6, address: 48, and set data: 00.3) Select page: 6, address: 9D, and set data: 00.4) Select page: 0, address: 01, and set data: 00.
Fig. 5-1-13.
Burst position
Burst position
For PAL model
For NTSC model
5-26
DCR-TRV16/TRV16E/TRV18/TRV18E/TRV116E/TRV118E
9. MAX GAIN AdjustmentSetting the minimum illumination.If it is not consistent, the image level required for taking subjects inlow illuminance will not be produced (dark).
Subject Clear chart(Color reproduction adjustment frame)
Adjustment Page F
Adjustment Address 1D
Note1: The data of page: 0, address: 10 must be “00”.Note2: Check that the data of page: 6, address: 02 is “00”. If not, to page:
6, address: 01, set data: 00, and press the PAUSE button.
Switch setting:1) POWER .................................................................. CAMERA2) NIGHT SHOT ..................................................................OFF3) DIGITAL ZOOM (Menu display) ...................................OFF4) STEADY SHOT (Menu display) .....................................OFF
Adjusting method:
Order Page Address Data Procedure
1 0 01 01 Set the data.
2 6 48 01 Set the data.
3 6 96 27 Set the data.
4 6 97 00 Set the data.
5 6 01 6F Set the data, and press PAUSEbutton.
6 6 02 Check that the data changes to“01”. (Note3)
Note3: The adjustment data will be automatically input to page: F, address:1D.
Processing after Completing Adjustments
Order Page Address Data Procedure
1 6 48 00 Set the data.
2 6 96 00 Set the data.
3 6 97 00 Set the data.
4 6 01 00 Set the data, and press PAUSEbutton.
5 0 01 00 Set the data.
10. Auto White Balance & LV Standard Data InputAdjust the white balance reference at 3200K, and adjust the normalcoefficient of the light value.
Subject Clear chart(Color reproduction adjustment frame)
Measurement Point Display data of page 1 (Note5)
Measuring Instrument Adjustment remote commander
Adjustment Page F
Adjustment Address 1E, 1F, 2A to 2D
Specified Value 0FF0 to 1010
Note1: This adjustments should be carried out upon completion of “Colorreproduction adjustment” and “MAX GAIN adjustment”.
Note2: After the power is turned on, this adjustment can be done onlyonce.
Note3: The data of page: 0, address: 10 must be “00”.Note4: Check that the data of page: 6, address: 02 is “00”. If not, to page:
6, address: 01, set data: 00, and press the PAUSE button.Note5: Displayed data of page 1 of the adjustment remote commander.
1 : XX : XXDisplay data
Switch setting:1) POWER .................................................................. CAMERA2) NIGHT SHOT ..................................................................OFF3) DIGITAL ZOOM (Menu display) ...................................OFF4) STEADY SHOT (Menu display) .....................................OFF
Adjusting method:
Order Page Address Data Procedure
1 0 01 01 Set the data.
2 6 48 01 Set the data.
3 Wait for 2 sec.
4 6 01 11 Set the data, and press PAUSEbutton.
5 6 01 0D Set the data, and press PAUSEbutton.
6 6 02 Check that the data changes to“01”. (Note6)
7 0 03 1E Set the data.
8 1 Check that the display data(Note5) satisfies the specifiedvalue.
Note6: The adjustment data will be automatically input to page: F, address:1E, 1F, 2A to 2D.
Processing after Completing Adjustments
Order Page Address Data Procedure
1 6 01 00 Set the data, and press PAUSEbutton.
2 6 48 00 Set the data.
3 0 03 00 Set the data.
4 0 01 00 Set the data.
5 Perform “Auto White BalanceAdjustment”.
5-27
DCR-TRV16/TRV16E/TRV18/TRV18E/TRV116E/TRV118E
11. Auto White Balance AdjustmentAdjust to the proper auto white balance output data.If it is not correct, auto white balance and color reproducibility willbe poor.
Subject Clear chart(Color reproduction adjustment frame)
Filter Filter C14 for color temperaturecorrection
Measurement Point Display data of page 1 (Note5)
Measuring Instrument Adjustment remote commander
Adjustment Page F
Adjustment Address 2E, 2F
Specified Value R ratio: 2B40 to 2C40B ratio: 5980 to 5A80
Note1: This adjustments should be carried out upon completion of “AutoWhite Balance & LV Standard Data Input”.
Note2: After the power is turned on, this adjustment can be done onlyonce.
Note3: The data of page: 0, address: 10 must be “00”.Note4: Displayed data of page 1 of the adjustment remote commander.
1 : XX : XXDisplay data
Switch setting:1) POWER .................................................................. CAMERA2) NIGHT SHOT .................................................................. OFF3) DIGITAL ZOOM (Menu display) ................................... OFF4) STEADY SHOT (Menu display) .....................................OFF
Adjusting method:
Order Page Address Data Procedure
1 Place the C14 filter for colortemperature correction on the lens.
2 0 01 01 Set the data.
3 6 48 01 Set the data.
4 F 3E Write down the data.
5 F 3E 2B Set the data, and press PAUSEbutton.
6 F 3F Write down the data.
7 F 3F C0 Set the data, and press PAUSEbutton.
8 F 40 Write down the data.
9 F 40 5A Set the data, and press PAUSEbutton.
10 F 41 Write down the data.
11 F 41 00 Set the data, and press PAUSEbutton.
12 6 01 83 Set the data, and press PAUSEbutton.
13 6 01 81 Set the data, and press PAUSEbutton.
14 6 02 Check that the data changes to“01”. (Note5)
15 6 01 3F Set the data, and press PAUSEbutton.
16 0 03 04 Set the data.
17 1 Check that the display data(Note4) satisfies the R ratiospecified value.
18 0 03 05 Set the data.
1 Check that the display data(Note4) satisfies the B ratiospecified value.
Note5: The adjustment data will be automatically input to page: F, address:2E, 2F.
Processing after Completing Adjustments:
Order Page Address Data Procedure
1 6 01 00 Set the data, and press PAUSEbutton.
2 6 48 00 Set the data.
3 F 3E Set the data that is written downat step 3, and press PAUSE button.
4 F 3F Set the data that is written downat step 5, and press PAUSE button.
5 F 40 Set the data that is written downat step 7, and press PAUSE button.
6 F 41 Set the data that is written downat step 9, and press PAUSE button.
7 0 03 00 Set the data.
8 0 01 00 Set the data.
5-28
DCR-TRV16/TRV16E/TRV18/TRV18E/TRV116E/TRV118E
12. White Balance Check
Subject Clear chart(Color reproduction adjustment frame)
Filter Filter C14 for color temperaturecorrectionND filter 1.0 and 0.4 and 0.1
Measurement Point Video output terminal
Measuring Instrument Vectorscope
Specified Value Fig. 5-1-14. A to B
Note1: The data of page: 0, address: 10 must be “00”.
Switch setting:1) POWER .................................................................. CAMERA2) NIGHT SHOT ..................................................................OFF3) DIGITAL ZOOM (Menu display) ...................................OFF4) STEADY SHOT (Menu display) .....................................OFF
Checking method:
Order Page Address Data Procedure
Indoor white balance check
1 Check that the lens is not coveredwith either filter.
2 6 48 01 Set the data.
3 6 01 0F Set the data, and press PAUSEbutton.
4 Check that the center of the whiteluminance point is within thecircle shown Fig. 5-1-14. A.
5 6 01 00 Set the data, and press PAUSEbutton.
Outdoor white balance check
6 Place the C14 filter on the lens.
7 6 01 3F Set the data, and press PAUSEbutton.
8 Check that the center of the whiteluminance point is within thecircle shown Fig. 5-1-14. B.
9 Remove the C14 filter.
LV data check
10 Place the ND filter 1.5(1.0+0.1+0.4) on the lens.
11 6 01 00 Set the data, and press PAUSEbutton.
12 0 03 06 Set the data.
13 1 Check that the display data (Note2)satisfies the specified value.
Specified value: 8000 to 8BC0
Note2: Displayed data of the adjustment remote commander.1 : XX : XX
Display data
Processing after Completing Adjustments
Order Page Address Data Procedure
1 6 01 00 Set the data, and press PAUSEbutton.
2 6 48 00 Set the data.
3 0 03 00 Set the data.
R-Y 2mm
B-Y
2mm
R-Y
B-Y0.5mm
1mm
3mm
3mm
Fig. 5-1-14 (A).
Fig. 5-1-14 (B).
5-29
DCR-TRV16/TRV16E/TRV18/TRV18E/TRV116E/TRV118E
13. Mechanical Shutter Adjustment(DCR-TRV18/TRV18E/TRV118E)
Adjustment Page F
Adjustment Address 66 to 7B
Note: The data of page: 0, address: 10 must be “00”.
Adjusting method:1) Select page: 0, address: 01, and set data: 01.2) Input the following data to page: F, addresses: 66 to 7B.
Note: Press the PAUSE button of the adjustment remote commandereach time to set the data.
3) Select page: 0, address: 01, and set data: 00.
Address
66
67
68
69
6A
6B
6C
6D
6E
6F
70
71
72
73
74
75
76
77
78
79
7A
7B
NTSC80
80
80
80
80
80
40
00
34
00
30
00
2A
00
28
00
70
80
80
80
80
1E
PAL80
80
80
80
80
80
3D
00
32
00
2C
00
27
00
24
00
6B
7A
83
83
75
1B
DATA
5-30
DCR-TRV16/TRV16E/TRV18/TRV18E/TRV116E/TRV118E
1-4. COLOR ELECTRONIC VIEWFINDERSYSTEM ADJUSTMENT
Note1: When replacing the LCD unit, be careful to prevent damagescaused by static electricity.
Note2: Before performing the adjustments, check the data of page: 0,address: 10 is “00”. If not, set data: 00 to this address.
Note3: As the PANEL CLOSE switch is attached to the cabinet (R), thiscabinet must be attached when performing adjustments.If you perform the adjustments with cabinet (R) removed, set thefollowing data.1) Select page: 3, address: C4, and set data: 67.2) Select page: 3, address: C5, and set data: 01.Reset the data after completing adjustment.1) Select page: 3, address: C4, and set data: 00.2) Select page: 3, address: C5, and set data: 00.
Note4: NTSC model: DCR-TRV16/TRV18PAL model: DCR-TRV16E/TRV18E/TRV116E/TRV118E
[Adjusting connector]Most of the measuring points for adjusting the viewfinder systemare concentrated in CN1002 of VC-280 board.Connect the Measuring Instruments via the CPC-8 jig (J-6082-388-A).The following table shows the Pin No. and signal name of CN1002.
Table 5-1-12.
1. VCO Adjustment (VA-117 board)Set the VCO free-run frequency. If deviated, the EVF screen will beblurred.
Mode Camera
Subject Arbitrary
Measurement Point Pin 5 of CN1002 of VC-280 board(EVF VCO)
Measuring Instrument Frequency counter
Adjustment Page C
Adjustment Address 51, 52
Specified Value f = 15734 ± 30Hz (NTSC)f = 15625 ± 30Hz (PAL)
Note1: The data of page: 0, address: 10 must be “00”.
Adjusting method:
Order Page Address Data Procedure
1 0 01 01 Set the data.
2 C 51 Change the data and set the VCOfrequency (f) to the specified value.
3 C 51 Press PAUSE button.
4 C 51 Read the data, and this data isnamed D51.
5 Convert D51 to decimal notation,and obtain D51’. (Note2)
6 Calculate D52’ using followingequations (Decimal calculation)[NTSC model]
When D51’ 231D52’ = D51’+24
When D51’ > 231D52’ = 255
[PAL model]When D51’ 24
D52’ = D51’ – 24When D51’ < 24
D52’ = 0
7 Convert D52’ to a hexadecimalnumber, and obtain D52. (Note2)
8 C 52 D52 Set the data, and press PAUSEbutton.
9 0 01 00 Set the data.
Note2: Refer to “Table 5-4-1. Hexadecimal-decimal Conversion Table”.
fig. 5-1-15.
Pin No.1
3
5
7
9
11
13
15
17
19
Signal NameN.C.
N.C.
EVF VCO
PANEL VG
H START
PANEL COM
N.C.
N.C.
SWP
GND
Pin No.
2
4
6
8
10
12
14
16
18
20
Signal NameN.C.
EVF VG
GND
PD VCO
XHD/PSIG
TMS (MAKER CHECK)
N.C.
GND
RF IN/LANC JACK IN
RF MON
CN1002
Removed the CPC lid.
2
19 20
1
5-31
DCR-TRV16/TRV16E/TRV18/TRV18E/TRV116E/TRV118E
2. RGB AMP Adjustment (VA-117 board)Set the D range of the RGB driver used to drive the LCD to thespecified value. If deviated, the LCD screen will become blackishor saturated (whitish).
Mode Camera
Subject Arbitrary
Measurement Point Pin 4 of CN1002 of VC-280 board(EVF VG)
Measuring Instrument Oscilloscope
Adjustment Page C
Adjustment Address 54
Specified Value A = 7.20 ± 0.10V (NTSC)A = 7.14 ± 0.10V (PAL)
Note: The data of page: 0, address: 10 must be “00”.
Adjusting method:
Order Page Address Data Procedure
1 0 01 01 Set the data.
2 C 54 Change the data and set thevoltage (A) between the reversedwaveform pedestal and non-reversed waveform pedestal to thespecified value.
3 C 54 Press PAUSE button.
4 0 01 00 Set the data.
3. Contrast Adjustment (VA-117 board)Set the level of the VIDEO signal for driving the LCD to the specifiedvalue. If deviated, the screen image will be blackish or saturated(whitish).
Mode Camera
Subject Arbitrary
Measurement Point Pin 4 of CN1002 of VC-280 board(EVF VG)
Measuring Instrument Oscilloscope
Adjustment Page C
Adjustment Address 58
Specified Value A = 2.52 ± 0.10V (NTSC)A = 2.38 ± 0.10V (PAL)
Note: The data of page: 0, address: 10 must be “00”.
Adjusting method:
Order Page Address Data Procedure
1 0 01 01 Set the data.
2 C 58 Change the data and set thevoltage (A) between the 100 IREand 0 IRE (pedestal) to thespecified value. (The data shouldbe “00” to “7F”.)
3 C 58 Press PAUSE button.
4 0 01 00 Set the data.
Pedestal
Pedestal
A
2H
3 steps peak
Pedestal
A
2H
Fig. 5-1-16. Fig. 5-1-17.
5-32
DCR-TRV16/TRV16E/TRV18/TRV18E/TRV116E/TRV118E
4. White Balance Adjustment (VA-117 board)
Correct the white balance.If deviated, the reproduction of the EVF screen may degenerate.
Mode Camera
Subject Arbitrary
Measurement Point Check on EVF screen
Measuring Instrument
Adjustment Page C
Adjustment Address 56, 57
Specified Value The EVF screen should not be colored.
Note1: Check the white balance only when replacing the following parts.If necessary, adjust them.1. LCD panel2. Light induction plate3. IC4201
Note2: The data of page: 0, address: 10 must be “00”.
Adjusting method:
Order Page Address Data Procedure
1 0 01 01 Set the data.
2 C 56 80 Set the data, and press PAUSEbutton.
3 C 57 80 Set the data, and press PAUSEbutton.
4 C 57 Check that the EVF screen is notcolored. If not colored, proceed tostep 10.
5 C 56 Change the data so that the EVFscreen is not colored.
6 C 56 Press PAUSE button.
7 C 57 Change the data so that the EVFscreen is not colored.
8 C 57 Press PAUSE button.
9 C 57 If the EVF screen is colored,repeat steps 5 to 9.
10 0 01 00 Set the data.
5-33
DCR-TRV16/TRV16E/TRV18/TRV18E/TRV116E/TRV118E
1-5. LCD SYSTEM ADJUSTMENT
Note1: The back light (fluorescent tube) is driven by a high voltage ACpower supply. Therefore, do not touch the back light holder toavoid electrical shock.
Note2: When replacing the LCD unit, be careful to prevent damagescaused by static electricity.
Note3: Before performing the adjustments, check the data of page: 0,address: 10 is “00”. If not, set data: 00 to this address.
Note4: NTSC model: DCR-TRV16/TRV18PAL model: DCR-TRV16E/TRV18E/TRV116E/TRV118E
Switch setting:LCD BRIGHT(Menu setting) ............................................. Center.
[Adjusting connector]Most of the measuring points for adjusting the LCD system areconcentrated in CN1002 of the VC-280 board. Connect themeasuring instruments via the multi CPC-8 jig (J-6082-388-A). Thefollowing table shows the Pin No. and signal name of CN1002.
Table 5-1-13.
1. VCO Adjustment (PD-161 board)Set the VCO free-run frequency. If deviated, the LCD screen willbe blurred.
Mode VTR stop
Signal No signal
Measurement Point Pin 9 of CN1002 of VC-280 board(H START)
Measuring Instrument Frequency counter
Adjustment Page C
Adjustment Address 61, 62
Specified Value f = 15734 ± 30Hz (NTSC)f = 15625 ± 30Hz (PAL)
Note1: The data of page: 0, address: 10 must be “00”.
Adjusting method:
Order Page Address Data Procedure
1 0 01 01 Set the data.
2 C 61 Change the data and set the VCOfrequency (f) to the specifiedvalue.
3 C 61 Press PAUSE button.
4 C 61 Read the data, and this data isnamed D61.
5 Convert D61 to decimal notation,and obtain D61’. (Note2)
6 Calculate D62’ using followingequations (Decimal calculation)[NTSC model]
When D61’ 229D62’ = D61’ + 26
When D61’ > 229D62’ = 255
[PAL model]When D61’ 26
D62’ = D61’ – 26When D61’ < 26
D62’ = 0
7 Convert D62’ to a hexadecimalnumber, and obtain D62. (Note2)
8 C 62 D62 Set the data, and press PAUSEbutton.
9 0 01 00 Set the data.
Note2: Refer to “Table 5-4-1. Hexadecimal-decimal Conversion Table”.
Pin No.1
3
5
7
9
11
13
15
17
19
Signal NameN.C.
N.C.
EVF VCO
PANEL VG
H START
PANEL COM
N.C.
N.C.
SWP
GND
Pin No.
2
4
6
8
10
12
14
16
18
20
Signal NameN.C.
EVF VG
GND
PD VCO
XHD/PSIG
TMS (MAKER CHECK)
N.C.
GND
RF IN/LANC JACK IN
RF MON
fig. 5-1-18.
CN1002
Removed the CPC lid.
2
19 20
1
5-34
DCR-TRV16/TRV16E/TRV18/TRV18E/TRV116E/TRV118E
2. RGB AMP Adjustment (PD-161 board)Set the D range of the RGB decoder used to drive the LCD to thespecified value. If deviated, the LCD screen will become blackishor saturated (whitish).
Mode VTR stop
Signal No signal
Measurement Point Pin 7 of CN1002 of VC-280 board(PANEL VG)Ext. trigger: Pin qa of CN1002 of VC-280 board (PANEL COM)
Measuring Instrument Oscilloscope
Adjustment Page C
Adjustment Address 64
Specified Value A = 3.52 ± 0.05V (NTSC)A = 3.63 ± 0.05V (PAL)
Note: The data of page: 0, address: 10 must be “00”.
Adjusting method:
Order Page Address Data Procedure
1 0 01 01 Set the data.
2 C 64 Change the data and set thevoltage (A) between the reversedwaveform pedestal and non-reversed waveform pedestal to thespecified value. (The data shouldbe “00” to “3F”.)
3 C 64 Press PAUSE button.
4 0 01 00 Set the data.
3. Contrast Adjustment (PD-161 board)Set the level of the VIDEO signal for driving the LCD to the specifiedvalue. If deviated, the screen image will be blackish or saturated(whitish).
Mode VTR stop
Signal No signal
Measurement Point Pin 7 of CN1002 of VC-280 board(PANEL VG)Ext. trigger: Pin qa of CN1002 of VC-280 board (PANEL COM)
Measuring Instrument Oscilloscope
Adjustment Page C
Adjustment Address 69
Specified Value A = 3.00 ± 0.05V (NTSC)A = 3.37 ± 0.05V (PAL)
Note: The data of page: 0, address: 10 must be “00”.
Adjusting method:
Order Page Address Data Procedure
1 0 01 01 Set the data.
2 C 69 Change the data and set thevoltage (A) between the 100 IREand 0 IRE (pedestal) to thespecified value. (The data shouldbe “00” to “7F”.)
3 C 69 Press PAUSE button.
4 0 01 00 Set the data.
Fig. 5-1-19.
Pedestal
Pedestal
A
2H
100 IRE
Pedestal
A
2H
Fig. 5-1-20.
5-35
DCR-TRV16/TRV16E/TRV18/TRV18E/TRV116E/TRV118E
4. COM AMP Adjustment (PD-161 board)
Set the common electrode drive signal level of LCD to the specifiedvalue.
Mode VTR stop
Signal No signal
Measurement Point Pin qa of CN1002 of VC-280 board(PANEL COM)
Measuring Instrument Oscilloscope
Adjustment Page C
Adjustment Address 66
Specified Value A = 5.97 ± 0.05V (NTSC)A = 6.34 ± 0.05V (PAL)
Note: The data of page: 0, address: 10 must be “00”.
Adjusting method:
Order Page Address Data Procedure
1 0 01 01 Set the data.
2 C 66 Change the data and set thePANEL COM signal level (A) tothe specified value.
3 C 66 Press PAUSE button.
4 0 01 00 Set the data.
5. V COM Adjustment (PD-161 board)Set the DC bias of the common electrode drive signal of LCD to thespecified value.If deviated, the LCD display will move, producing flicker andconspicuous vertical lines.
Mode VTR stop
Signal No signal
Measurement Point Check on LCD display
Measuring Instrument
Adjustment Page C
Adjustment Address 63
Specified Value The brightness difference between thesection A and section B is minimum.
Note1: This adjustment should be carried out upon completion of thefollowing adjustments.
RGB AMP AdjustmentContrast AdjustmentCOM AMP Adjustment
Note2: The data of page: 0, address: 10 must be “00”.
Adjusting method:
Order Page Address Data Procedure
1 0 01 01 Set the data.
2 C 63 Change the data so that thebrightness of the section A andthat of the section B is equal.
3 C 63 Subtract 8 from the data.
4 C 63 Press PAUSE button.
5 0 01 00 Set the data.
Fig. 5-1-21.
Fig. 5-1-22.
A
A
A
A
B
B
B
B
A
2H
5-36
DCR-TRV16/TRV16E/TRV18/TRV18E/TRV116E/TRV118E
6. White Balance Adjustment (PD-161 board)Correct the white balance.If deviated, the reproduction of the LCD screen may degenerate.
Mode VTR stop
Signal No signal
Measurement Point Check on LCD screen
Measuring Instrument
Adjustment Page C
Adjustment Address 67, 68
Specified Value The LCD screen should not be colored.
Note1: Check the white balance only when replacing the following parts.If necessary, adjust them.1. LCD panel2. Light induction plate3. IC5501
Note2: The data of page: 0, address: 10 must be “00”.
Adjusting method:
Order Page Address Data Procedure
1 0 01 01 Set the data.
2 C 67 80 Set the data, and press PAUSEbutton.
3 C 68 80 Set the data, and press PAUSEbutton.
4 C 68 Check that the LCD screen is notcolored. If not colored, proceed tostep 10.
5 C 67 Change the data so that the LCDscreen is not colored.
6 C 67 Press PAUSE button.
7 C 68 Change the data so that the LCDscreen is not colored.
8 C 68 Press PAUSE button.
9 C 68 If the LCD screen is colored,repeat steps 5 to 9.
10 0 01 00 Set the data.
5-37
DCR-TRV16/TRV16E/TRV18/TRV18E/TRV116E/TRV118E
5-2. MECHANISM SECTIONADJUSTMENT
On the mechanism section adjustmentFor detail of mechanism section adjustments, checks, andreplacement of mechanism parts, refer to the separate volume “DVMECHANICAL ADJUSTMENT MANUAL J Mechanism ”.Note: Before performing the adjustments, check the data of page: 0,
address: 10 is “00”. If not, set data: 00 to this address.
2-1. HOE TO ENTER RECORD MODE WITHOUTCASSETTE
1) Connect the adjustment remote commander to the LANC jack.2) Turn the HOLD switch of the adjustment remote commander
to the ON position.3) Close the cassette compartment without the cassette.4) Select page: 3, address: 01, and set data: 0C, and press the
PAUSE button of the adjustment remote commander.(The mechanism enters the record mode automatically.)Note: The function buttons becomes inoperable.
5) To quit the record mode, select page: 3, address: 01, set data:00, and press the PAUSE button of the adjustment remotecommander. (Whenever you want to quit the record mode, besure to quit following this procedure.)
2-2. HOE TO ENTER PLAYBACK MODEWITHOUT CASSETTE
1) Connect the adjustment remote commander to the LANC jack.2) Turn the HOLD switch of the adjustment remote commander
to the ON position.3) Close the cassette compartment without the cassette.4) Select page: 3, address: 01, and set data: 0B, and press the
PAUSE button of the adjustment remote commander.(The mechanism enters the playback mode automatically.)Note: The function buttons becomes inoperable.
5) To quit the playback mode, select page: 3, address: 01, set data:00, and press the PAUSE button of the adjustment remotecommander. (Whenever you want to quit the playback mode,be sure to quit following this procedure.)
2-3. TAPE PATH ADJUSTMENT
1. Preparation for Adjustment
1) Clean the tape running side (tape guide, drum, capstan shaft,pinch roller, etc.).
2) Connect the adjustment remote commander to the LANC jack.3) Turn the HOLD switch of the adjustment remote commander
to the ON position.4) Connect an oscilloscope to VC-280 board CN1002 via the CPC-
8 jig (J-6082-388-A).Channel 1: VC-280 board, CN1002 Pin w; (Note)External trigger: VC-280 board, CN1002 Pin qjNote: Connect a 75Ω resistor between Pins w; of CN1002 and ql
(GND).5) Playback the alignment tape for tracking. (XH2-1)6) Select page: 3, address: 33, and set data: 08.7) Select page: 3, address: 26, and set data: 31.8) Check that the oscilloscope RF waveform is normal at the
entrance and exit.If not normal, adjust according to the separate volume“DV MECHANICAL ADJUSTMENT MANUAL J Mechanism ”.
CN1002 of VC-280 board
Table 5-2-1.
2. Processing after Completing Operations:1) Connect the adjustment remote commander to the LANC jack
and set the HOLD switch to the ON position.2) Select page: 3, address: 26, and set data: 00.3) Select page: 3, address: 33, and set data: 00.
CH1
Entrance side Exit sideCheck this section(Normal waveform)
CH2(Trigger)
3.3msec
Fig. 5-2-1.
Pin No.1
3
5
7
9
11
13
15
17
19
Signal NameN.C.
N.C.
EVF VCO
PANEL VG
H START
PANEL COM
N.C.
N.C.
SWP
GND
Pin No.2
4
6
8
10
12
14
16
18
20
Signal NameN.C.
EVF VG
GND
PD VCO
XHD/PSIG
TMS (MAKER CHECK)
N.C.
GND
RF IN/LANC JACK IN
RF MON
5-38
DCR-TRV16/TRV16E/TRV18/TRV18E/TRV116E/TRV118E
5-3. VIDEO SECTION ADJUSTMENTS
NTSC model : DCR-TRV16/TRV18PAL model : DCR-TRV16E/TRV18E/TRV116E/TRV118E
3-1. PREPARATIONS BEFORE ADJUSTMENTS
Use the following measuring instruments for video sectionadjustments.
3-1-1. Equipment Required
1) TV monitor2) Oscilloscope (dual-phenomenon, band above 30 MHz with
delay mode) (Unless specified otherwise, use a 10 : 1 probe.)3) Frequency counter4) Pattern generator with video output terminal.5) Digital voltmeter6) Audio generator7) Audio level meter8) Audio distortion meter9) Audio attenuator10) Regulated power supply11) Alignment tapes
• Tracking standard (XH2-1)Parts code: 8-967-997-01
• SW/OL standard (XH2-3)Parts code: 8-967-997-11
• Audio operation check for NTSC (XH5-3)Parts code: 8-967-997-51
• System operation check for NTSC (XH5-5)Parts code: 8-967-997-61
• Audio operation check for PAL (XH5-3P)Parts code: 8-967-997-55
• System operation check for PAL (XH5-5P)Parts code: 8-967-997-66
12) Adjustment remote commander (J-6082-053-B)13) CPC-8 jig (J-6082-388-A)14) Extension cable (100P, 0.5mm) (J-6082-352-A)
For extension between the VA-117 board (CN4002) and VC-280 board (CN1007).
5-39
DCR-TRV16/TRV16E/TRV18/TRV18E/TRV116E/TRV118E
3-1-2. Precautions on AdjustingNote1: Before performing the adjustments, check the data of page: 0,
address: 10 is “00”. If not, set data: 00 to this address.1) The adjustments of this unit are performed in the VTR mode
or camera mode.To set to the VTR mode, set the power switch to “VCR” (or“PLAYER”) or set the “Forced VTR Power ON mode” usingthe adjusting remote commander (Note2).To set to the Camera mode, set the power switch to “CAMERA”or set the “Forced Camera Power ON mode” using the adjustingremote commander (Note3).After completing adjustments, be sure to exit the “Forced VTRPower ON Mode” or “Forced Camera Power ON Mode”.(Note5)
2) The front panel block ( Focus ring, Microphone unit., MA-409board, FB-219 board) need not be assembled. To remove it,disconnect the following connector.
VA-117 board CN4003 (24P, 0.5mm)3) Cabinet (R) (CK-108board, LCD block) need not be connected.
But removing the cabinet (R) (removing the VC-280 boardCN1005) means removing the lithium 3V power supply (CK-108 board, BT5201) , data such as date, time, user-set menuswill be lost. After completing adjustments, reset these data.But, the self-diagnosis data and the data on history of use (totaldrum rotation time etc.) will be kept even if the cabinet (R) hasbeen removed. (Refer to “5-4.Service Mode” for the data onthe history use and the self-diagnosis data.)To remove the cabinet (R), disconnect the following connectors.
VA-117 board CN4004 (12P, 0.5mm)VC-280 board CN1005 (28P, 0.5mm)
4) The EVF block (LB-077 board) is need not be connected. Toremove it, disconnect the following connector.
VA-117 board CN4201 (20P, 0.5mm)5) The intelligent accessory shoe is need not be connected. To
remove it, disconnect the following connector.VA-117 board CN4001 (20P, 0.5mm)
6) To open the VA-117 board, use the following extension cablebetween the VA-117 board CN4002 and VC-280 boardCN1007.
J-6082-352-A (100P, 0.5mm)7) The lens block (CD-365 board) is need not be connected. To
remove it, disconnect the following connectors.VC-280 board CN1401 (16P, 0.5mm)VC-280 board CN1201 (24P, 0.5mm)
8) By setting the “Forced VTR Power ON mode”, the video sectioncan be operate even if the control switch block (PS-CX2670)has been removed. When removing it, disconnect the followingconnector.
VC-280 board CN1008 (20P, 0.5mm)
Note2: Setting the “Forced VTR Power ON” mode (VTR mode)1) Select page: 0, address: 01, and set data: 01.2) Select page: D, address: 10, set data: 02, and press the PAUSE
button of the adjusting remote commander.The above procedure will enable the VTR power to be turnedon with the control switch block (PS-CX2670 block) removed.After completing adjustments, be sure to exit the “Forced PowerON mode”.
Note3: Setting the “Forced Camera Power ON” mode (Camera mode)1) Select page: 0, address: 01, and set data: 01.2) Select page: D, address: 10, set data: 01, and press the PAUSE
button of the adjusting remote commander.The above procedure will enable the camera power to be turnedon with the control switch block (PS-CX2670 block) removed.After completing adjustments, be sure to exit the “Forced PowerON mode”.
Note4: Setting the “Forced Memory Power ON” mode (Memory mode)1) Select page: 0, address: 01, and set data: 01.2) Select page: D, address: 10, set data: 05, and press the PAUSE
button of the adjusting remote commander.The above procedure will enable the memory power to beturned on with the control switch block (PS-CX2670 block)removed.After completing adjustments, be sure to exit the “Forced PowerON mode”.
Note5: Exiting the “Forced Power ON” mode1) Select page: 0, address: 01, and set data: 01.2) Select page: D, address: 10, set data: 00, and press the PAUSE
button of the adjusting remote commander.3) Select page: 0, address: 01, and set data: 00.
5-40
DCR-TRV16/TRV16E/TRV18/TRV18E/TRV116E/TRV118E
3-1-3. Adjusting ConnectorsSome of the adjusting points of the video section are concentratedat VC-280 board CN1002. Connect the measuring instruments viathe CPC-8 jig (J-6082-388-A). The following table lists the pinnumbers and signal names of CN1002.
Table 5-3-1.
3-1-4. Connecting the EquipmentConnect the measuring instruments as shown in Fig. 5-3-2, andperform the adjustments.
Adjustmentremote
commander
LANC jack
Main unit
AUDIO/VIDEO jack
TV monitor
VIDEO(Yellow)
AUDIO L (White)
AUDIO R (Red)
Pin No.1
3
5
7
9
11
13
15
17
19
Signal NameN.C.
N.C.
EVF VCO
PANEL VG
H START
PANEL COM
N.C.
N.C.
SWP
GND
Pin No.2
4
6
8
10
12
14
16
18
20
Signal NameN.C.
EVF VG
GND
PD VCO
XHD/PSIG
TMS (MAKER CHECK)
N.C.
GND
RF IN/LANC JACK IN
RF MON
Fig. 5-3-2.
Fig. 5-3-1.
CN1002
Removed the CPC lid.
2
19 20
1
5-41
DCR-TRV16/TRV16E/TRV18/TRV18E/TRV116E/TRV118E
3-1-5. Alignment TapesUse the alignment tapes shown in the following table.Use tapes specified in the signal column of each adjustment.
Fig. 5-3-3 shows the 75% color bar signals recorded on the alignmenttape for Audio Operation Check.
Note: Measure with video terminal (Terminated at 75 Ω)
UseTape path adjustment
Switching position adjustment
Audio system adjustment
Operation check
NameTracking standard (XH2-1)
SW/OL standard (XH2-3)
Audio operation check(XH5-3 (NTSC), XH5-3P (PAL))
System operation check(XH5-5 (NTSC), XH5-5P (PAL))
For NTSC model
For PAL model
Color bar signal waveform Color bar pattern
Color bar signal waveform Color bar pattern
Fig. 5-3-3. Color bar signal of alignment tapes
3-1-6. Input/Output Level and ImpedanceVideo input/output
Special stereo mini jackVideo signal: 1 Vp-p, 75 Ω unbalanced,
sync negativeS video input/output
4-pin mini DINLuminance signal: 1 Vp-p, 75 Ω unbalanced,
sync negativeChrominance signal: 0.286 Vp-p, 75 Ω unbalanced (NTSC)
: 0.300 Vp-p, 75 Ω unbalanced (PAL)
Audio input/outputSpecial stereo mini jackInput level: 327mVInput impedance: More than 47kΩOutput level: 327 mV (at load impedance 47 kΩ)Output impedance: Below 2.2 kΩ
1V
0.714V
0.286V
White (75%)
White (100%)
Yello
w
Cya
nG
reen
Mag
enta
Red
Blu
e Burst signal
0.286V
Q I
Horizontal sync signal
(75%)
Whi
te
Yello
w
Cya
n
Gre
en
Mag
enta
Red
Blu
e
Q I
White(100%)
Black
1V0.7V
0.3V
White (100%)
Yello
w
Cya
nG
reen
Mag
enta
Red
Blu
e
Burst signalHorizontal sync signal
0.3V(100%)
Yello
w
Cya
n
Gre
en
Mag
enta
Red
Blu
e
Whi
te
Bla
ck
5-42
DCR-TRV16/TRV16E/TRV18/TRV18E/TRV116E/TRV118E
3-2. SYSTEM CONTROL SYSTEM ADJUSTMENT
1. Initialization of 8, A, B, C, D, E, F, 1B, 1F Page DataIf the 8, A, B, C, D, E, F, 1B, 1F page data is erased due to somereason, perform “1-2. INITIALIZATION OF 8, A, B, C, D, E, F, 1B,1F PAGE DATA” of “5-1. CAMERA SECTION ADJUSTMENT”.Note: When reading or writing the 1B, 1F page data, select page: 0,
address: 10, and set data: 01, then select B or F page. The 1B or1F page can be chosen by this data setting.After reading or writing, reset the data of page: 0, address: 10 to“00”.
2. Serial No. InputNote: Before performing the adjustments, check the data of page: 0,
address: 10 is “00”. If not, set data: 00 to this address.
2-1. Company ID InputWrite the company ID in the EEPROM (nonvolatile memory).
Page 8
Address 8C, 8D, 8E, 8F, 90
Input method:1) Select page: 0, address: 01, and set data: 01.2) Input the following data to page: 8, addresses: 8C to 90.
Note: Press the PAUSE button of the adjustment remote commandereach time to set the data.
3) Select page: 0, address: 01, and set data: 00.
2-2. Serial No. InputWrite the serial No. and model code in the EEPROM (nonvolatilememory). Convert the serial No. on the name plate from decimal tohexadecimal, and write in the EEPROM.
Page 8
Address 91, 92, 93
Input method:1) Select page: 0, address: 01, and set data: 01.2) Read the serial No. on the name plate, and take it as D1.
Example: If the serial No. is 77881.D1 = 77881
Note: Use six digits of the low rank when a serial No. is more thanseven digits.
3) Obtain D2 and H1 corresponding to D1 from Table 5-3-2.Example: If D1 is “77881”.
D2 = D1 – 65536 = 12345H1 = FE
Address8C
8D
8E
8F
90
Data08
00
46
01
02
D1 (Decimal)
000001 to 065535
065536 to 131071
131072 to 196607
D2 (Decimal)
D1
D1–65536
D1–131072
H1 (Hexadecimal)(Service model code)FE
FE
FE
Table 5-3-2.
4) Input H1 to page: 8, address: 91. (Model code input)Example: If H1 is “FE”.
Select page: 8, address: 91, set data: FE, andpress the PAUSE button.
5) Obtain the maximum decimal not exceeding D2 from Table 5-3-3, and take this as D3.
Example: If D2 is “12345”.D3 = 12288
6) Obtain the hexadecimal corresponding to D3 from Table 5-3-3, and take this as H3.
Example: If D3 is “12288”.H3 = 3000
7) Obtain the difference D4 between D2 and D3. (Decimalcalculation, 0 D4 255)
D4 = D2 – D3
Example: If D2 is “12345” and D3 is “12288”.D4 = 12345 – 12288 = 57
8) Convert D4 to hexadecimal, and take this as H4.(Refer to “Hexadecimal-decimal conversion table” in “5-4.Service Mode”.)
Example: If D4 is “57”.H4 = 39
9) Input the upper 2 digits of H3 to page: 8, address: 92.Example: If H3 is “3000”.
Select page: 8, address: 92, set data: 30, andpress the PAUSE button.
10) Input H4 to page: 8, address: 93.Example: If H4 is “39”.
Select page: 8, address: 93, set data: 39, andpress the PAUSE button.
11) Select page: 0, address: 01, and set data: 00.
5-43
DCR-TRV16/TRV16E/TRV18/TRV18E/TRV116E/TRV118E
Decimal(D3)
Hexa-decimal
(H3)
Decimal(D3)
Hexa-decimal
(H3)
Decimal(D3)
Hexa-decimal
(H3)
Decimal(D3)
Hexa-decimal
(H3)
Decimal(D3)
Hexa-decimal
(H3)
Decimal(D3)
Hexa-decimal
(H3)
Decimal(D3)
Hexa-decimal
(H3)
Decimal(D3)
Hexa-decimal
(H3)
0
256
512
768
1024
1280
1536
1792
2048
2304
2560
2816
3072
3328
3584
3840
4096
4352
4608
4864
5120
5376
5632
5888
6144
6400
6656
6912
7168
7424
7680
7936
8192
8448
8704
8960
9216
9472
9728
9984
10240
10496
10752
11008
11264
11520
11776
12032
12288
12544
12800
13056
13312
13568
13824
14080
14336
14592
14848
15104
15360
15616
15872
16128
16384
16640
16896
17152
17408
17664
17920
18176
18432
18688
18944
19200
19456
19712
19968
20224
20480
20736
20992
21248
21504
21760
22016
22272
22528
22784
23040
23296
23552
23808
24064
24320
24576
24832
25088
25344
25600
25856
26112
26368
26624
26880
27136
27392
27648
27904
28160
28416
28672
28928
29184
29440
29696
29952
30208
30464
30720
30976
31232
31488
31744
32000
32256
32512
32768
33024
33280
33536
33792
34048
34304
34560
34816
35072
35328
35584
35840
36096
36352
36608
36864
37120
37376
37632
37888
38144
38400
38656
38912
39168
39424
39680
39936
40192
40448
40704
40960
41216
41472
41728
41984
42240
42496
42752
43008
43264
43520
43776
44032
44288
44544
44800
45056
45312
45568
45824
46080
46336
46592
46848
47104
47360
47616
47872
48128
48384
48640
48896
49152
49408
49664
49920
50176
50432
50688
50944
51200
51456
51712
51968
52224
52480
52736
52992
53248
53504
53760
54016
54272
54528
54784
55040
55296
55552
55808
56064
56320
56576
56832
57088
57344
57600
57856
58112
58368
58624
58880
59136
59392
59648
59904
60160
60416
60672
60928
61184
61440
61696
61952
62208
62464
62720
62976
63232
63488
63744
64000
64256
64512
64768
65024
65280
0000
0100
0200
0300
0400
0500
0600
0700
0800
0900
0A00
0B00
0C00
0D00
0E00
0F00
1000
1100
1200
1300
1400
1500
1600
1700
1800
1900
1A00
1B00
1C00
1D00
1E00
1F00
2000
2100
2200
2300
2400
2500
2600
2700
2800
2900
2A00
2B00
2C00
2D00
2E00
2F00
3000
3100
3200
3300
3400
3500
3600
3700
3800
3900
3A00
3B00
3C00
3D00
3E00
3F00
4000
4100
4200
4300
4400
4500
4600
4700
4800
4900
4A00
4B00
4C00
4D00
4E00
4F00
5000
5100
5200
5300
5400
5500
5600
5700
5800
5900
5A00
5B00
5C00
5D00
5E00
5F00
6000
6100
6200
6300
6400
6500
6600
6700
6800
6900
6A00
6B00
6C00
6D00
6E00
6F00
7000
7100
7200
7300
7400
7500
7600
7700
7800
7900
7A00
7B00
7C00
7D00
7E00
7F00
8000
8100
8200
8300
8400
8500
8600
8700
8800
8900
8A00
8B00
8C00
8D00
8E00
8F00
9000
9100
9200
9300
9400
9500
9600
9700
9800
9900
9A00
9B00
9C00
9D00
9E00
9F00
A000
A100
A200
A300
A400
A500
A600
A700
A800
A900
AA00
AB00
AC00
AD00
AE00
AF00
B000
B100
B200
B300
B400
B500
B600
B700
B800
B900
BA00
BB00
BC00
BD00
BE00
BF00
C000
C100
C200
C300
C400
C500
C600
C700
C800
C900
CA00
CB00
CC00
CD00
CE00
CF00
D000
D100
D200
D300
D400
D500
D600
D700
D800
D900
DA00
DB00
DC00
DD00
DE00
DF00
E000
E100
E200
E300
E400
E500
E600
E700
E800
E900
EA00
EB00
EC00
ED00
EE00
EF00
F000
F100
F200
F300
F400
F500
F600
F700
F800
F900
FA00
FB00
FC00
FD00
FE00
FF00
Table 5-3-3.
5-44
DCR-TRV16/TRV16E/TRV18/TRV18E/TRV116E/TRV118E
3-3. SERVO AND RF SYSTEM ADJUSTMENTBefore perform the servo and RF system adjustments, check thatthe specified value of “36 MHz Origin Oscillation Adjustment” of“CAMERA SYSTEM ADJUSTMENT” is satisfied.And check that the data of page: 0, address: 10 is “00”. If not, setdata: 00 to this address.
Adjusting Procedure:1. CAP FG duty adjustment2. PLL f0 & LPF f0 adjustment3. Switching position adjustment4. AGC center level and APC & AEQ adjustment5. PLL f0 & LPF f0 fine adjustment
1. Cap FG Duty Adjustment (VC-280 Board)Set the Cap FG signal duty cycle to 50% to establish an appropriatecapstan servo. If deviated, the uneven rotation of capstan and noisecan occur.
Measurement Point Display data of page: 3, address: 02, 03
Measuring Instrument Adjustment remote commander
Adjustment Page C
Adjustment Address 16
Specified Value Data of page: 3, address: 02 is “00”.Data of page: 3, address: 03 is “00”.
Note1: The data of page: 0, address: 10 must be “00”.
Adjusting method:
Order Page Address Data Procedure
1 Close the cassette compartmentwithout inserting a cassette.
2 0 01 01 Set the data.
3 3 01 1B Set the data, and press PAUSEbutton.
4 3 02 Check that the data changes inthe following order.“1B” t “2B” t “00”
5 3 03 Check that the data is “00”.(Note2)
6 0 01 00 Set the data.
Note2: If the data is “01”, adjustment has errors or the mechanism deck isdefective.
2. PLL f0 & LPF f0 Adjustment (VC-280 Board)
Mode VTR stop
Measurement Point Display data of page: 3, address: 02, 03
Measuring Instrument Adjustment remote commander
Adjustment Page C
Adjustment Address 1F, 20, 22, 29
Specified Value Data of page: 3, address: 02 is “00”.Data of page: 3, address: 03 is “00”.
Note1: The data of page: 0, address: 10 must be “00”.
Adjusting method:
Order Page Address Data Procedure
1 0 01 01 Set the data.
2 C 21 DC Set the data, and press PAUSEbutton.
3 3 01 30 Set the data, and press PAUSEbutton.
4 3 02 Check that the data changes to“00” with in 5 sec. (Note2)
5 3 03 Check that the data is “00”.(Note2)
6 0 01 00 Set the data.
Note2: If it isn’t satisfied, select page: C, address: 21, set the followingdata, and press the PAUSE button, and repeat steps 3 to 5.
There are errors when it isn’t satisfied even if the above treatmentis done.If bit2, bit3, bit4, bit5 or bit 6 of the data of page: 3, address: 03 is“1”, there are errors. For the error contents, see the following table.(For the bit values, refer to “5-4. SERVICE MODE”, “4-3. 3. Bitvalue discrimination”.)
Setting dataE0
D8
E4
D4
When the data of page: C, address: 21 is “DC”.
When the data of page: C, address: 21 is “E0”.
When the data of page: C, address: 21 is “D8”.
When the data of page: C, address: 21 is “E4”
Bit value of page: 3,address: 03 databit 2 = 1 or bit 3 = 1
bit 4 = 1 or bit 5 = 1
bit 6 = 1
Error contents
PLL f0 fine adjustment is defective
PLL f0 adjustment is defective
LPF f0 is defective
5-45
DCR-TRV16/TRV16E/TRV18/TRV18E/TRV116E/TRV118E
3. Switching Position Adjustment (VC-280 Board)To obtain normal playback waveform output during the Digital8playback mode, adjust the switching position.
Mode VTR playback
Signal SW/OL reference tape (XH2-3)
Measurement Point Display data of page: 3, address: 02, 03
Measuring Instrument Adjustment remote commander
Adjustment Page C
Adjustment Address 10, 11, 12, 13
Specified Value Data of page: 3, address: 02 is “00”.Data of page: 3, address: 03 is “00”.
Note1: The data of page: 0, address: 10 must be “00”.
Adjusting method:
Order Page Address Data Procedure
1 Insert the SW/OL reference tapeand enter the VTR STOP mode.
2 0 01 01 Set the data.
3 C 10 EE Set the data, and press PAUSEbutton.
4 3 21 Check that the data is “02”.(Note2)
5 3 01 0D Set the data, and press PAUSEbutton.
6 3 02 Check that the data changes to“00”.
7 3 03 Check that the data is “00”.(Note3)
8 0 01 00 Set the data.
Note2: If the data of page: 3, address: 21 is “72”, the tape top being played.After playing the tape for 1 to 2 seconds, stop it, perform step 5and higher.If the data of page: 3, address: 21 is “62”, the tape end being played.After rewinding the tape, perform step 5 and higher.
Note3: If bit 0 of the data is “1”, the EVEN channel is defective. If bit 1 is“1”, the ODD channel is defective. Contents of the defect is writteninto page: C, addresses: 10 and 12. See the following table. (Forthe bit values, refer to “5-4. SERVICE MODE”, “4-3. 3. Bit valuediscrimination”.) If bit 3 of the data is “1”, the tape end beingplayed, so rewind the tape and perform the adjustment again.
When the EVEN channel is defective
When the ODD channel is defective
Data of page: C,address: 10EE
E8
E7
Contents of defect
Writing into EEPROM (IC2502) is defective
Adjustment data is out of range
No data is returned from IC2101
Data of page: C,address: 12EE
E8
E7
Contents of defect
Writing into EEPROM (IC2502) is defective
Adjustment data is out of range
No data is returned from IC2101
4. AGC Center Level and APC & AEQ AdjustmentNote: The data of page: 0, address: 10 must be “00”.
4-1. Preparations before adjustments
Mode Camera recording
Subject Arbitrary
Adjusting method:
Order Page Address Data Procedure
1 7 30 80 Set the data.
2 Record the camera signal forthree minutes.
4-2. AGC Center Level Adjustment (VC-280 Board)
Mode Playback
Signal Recorded signal at “Preparationsbefore adjustments”
Measurement Point Pin w; of CN1002 (RF MON) (Note1)Ext. trigger: Pin qj of CN1002 (SWP)
Measuring Instrument Oscilloscope
Adjustment Page C
Adjustment Address 1E
Specified Value Data of page: 3, address: 02 is “00”.Data of page: 3, address: 03 is “00”.
Note1: Connect a 75Ω resistor between Pin w; and Pin ql (GND) ofCN1002.75Ω resistor (Parts code: 1-247-804-11)
Adjusting method:
Order Page Address Data Procedure
1 Playback the recorded signal at“Preparations before adjustments”
2 0 01 01 Set the data.
3 3 33 08 Set the data.
4 Confirm that the playback RFsignal is stable. (Fig. 5-3-4.)
5 3 01 23 Set the data, and press PAUSEbutton.
6 3 02 Check that the data is “00”.
7 3 03 Check that the data is “00”.(Note2)
8 Perform “APC & AEQAdjustment”.
Note2: If the data of page: 3, address: 03 is other than “00”, adjustmenthas errors. (Take an appropriate remedial measures according tothe errors referring to the following table.)
Data Contents of defect
20 Perform re-adjustment. (Note 3)
30 The machine is defective
40 Perform re-adjustment. (Note 3)
50 The machine is defective
Note3: If this data is displayed twice successively, the machine is defective.
5-46
DCR-TRV16/TRV16E/TRV18/TRV18E/TRV116E/TRV118E
4-3. APC & AEQ Adjustment (VC-280 Board)
Mode Playback
Signal Recorded signal at “Preparationsbefore adjustments”
Measurement Point Pin w; of CN1002 (RF MON) (Note1)Ext. trigger: Pin qj of CN1002 (SWP)
Measuring Instrument Oscilloscope
Adjustment Page C
Adjustment Address 18, 19, 1B, 1C, 21, 2C
Specified Value Data of page: 3, address: 02 is “00”.Data of page: 3, address: 03 is “00”.
Note1: Connect a 75Ω resistor between Pin w; and Pin ql (GND) ofCN1002.
75Ω resistor (Parts code: 1-247-804-11)Note2: The “AGC Center Level Adjustment” must have already been
completed before starting this adjustment.
Adjusting method:
Order Page Address Data Procedure
1 Playback the recorded signal at“Preparations before adjustments”
2 0 01 01 Set the data.
3 3 33 08 Set the data.
4 Confirm that the playback RFsignal is stable. (Fig. 5-3-4.)
5 3 01 07 Set the data, and press PAUSEbutton.
6 3 02 Check that the data changes from“07” to “00” in about 20 secondsafter pressing PAUSE button.
7 3 03 Check that the data is “00”.(Note3)
8 Perform “Processing afterCompleting Adjustments”.
Note3: If the data is other than “00”, adjustment has errors. Take anappropriate remedial measures according to the errors referring tothe following table.
Data Contents of defect
20 Perform re-adjustment. (Note 4)
30 The machine is defective
50 Perform re-adjustment. (Note 4)
60 The machine is defective
80 The machine is defective
Note4: If this data is displayed twice successively, the machine is defective.
4-4. Processing after Completing Adjustments
Order Page Address Data Procedure
1 7 30 00 Set the data.
2 3 33 00 Set the data.
3 0 01 00 Set the data.
6.7 msec
PB RF signal is stable
Pin qj
Pin w;
Fig. 5-3-4.
5-47
DCR-TRV16/TRV16E/TRV18/TRV18E/TRV116E/TRV118E
5. PLL f0 & LPF f0 Fine Adjustment (VC-280 Board)
Mode VTR stop
Signal Arbitrary
Measurement Point Display data of page: 3, address: 02, 03
Measuring Instrument Adjustment remote commander
Adjustment Page C
Adjustment Address 1F, 20, 22, 29
Specified Value Data of page: 3, address: 02 is “00”.Data of page: 3, address: 03 is “00”.
Note1: The data of page: 0, address: 10 must be “00”.
Adjusting method:
Order Page Address Data Procedure
1 0 01 01 Set the data.
2 3 01 30 Set the data, and press PAUSEbutton.
3 3 02 Check that the data changes to“00” with in 5 sec. (Note2)
4 3 03 Check that the data is “00”.(Note3)
5 0 01 00 Set the data.
Note2: If it isn’t satisfied, there are errors.Note3: If the data of page: 3, address: 03 is other than “00”, there are
errors. For the error contents, see the following table. (For the bitvalues, refer to “5-4. SERVICE MODE”, “4-3. 3. Bit valuediscrimination”.)
Bit value of page: 3,address: 03bit 2 = 1 or bit 3 = 1
bit 4 = 1 or bit 5 = 1
bit 6 = 1
Error contents
PLL f0 fine adjustment is defective
PLL f0 adjustment is defective
LPF f0 is defective
5-48
DCR-TRV16/TRV16E/TRV18/TRV18E/TRV116E/TRV118E
3-4. VIDEO SYSTEM ADJUSTMENTSNote1: Before perform the video system adjustments, check that the
specified value of “36 MHz Origin Oscillation Adjustment” of“CAMERA SYSTEM ADJUSTMENT” is satisfied.And check that the data of page: 0, address: 10 is “00”. If not, setdata: 00 to this address.
Note2: NTSC model: DCR-TRV16/TRV18PAL model: DCR-TRV16E/TRV18E/TRV116E/TRV118E
1. Chroma BPF fo Adjustment (VA-117 Board)Set the center frequency of IC4101 chroma band-pass filter.
Mode Camera
Subject Arbitrary
Measurement Point CH1: Chroma signal terminal of SVIDEO jack (75Ω terminated)CH2: Y signal terminal of S VIDEO jack(75Ω terminated)
Measuring Instrument Oscilloscope
Adjustment Page C
Adjustment Address 28
Specified Value A = 100mVp-p or lessB = 200mVp-p or more
Note: The data of page: 0, address: 10 must be “00”.
Adjusting method:
Order Page Address Data Procedure
1 0 01 01 Set the data.
2 Check that the burst signal (B) isoutput to the chroma signalterminal of S VIDEO jack.
3 3 0C 04 Set the data, and press PAUSEbutton.
4 C 28 Change the data for minimumamplitude of the burst signallevel (A).(The data should be “00” to “0F”.)
5 C 28 Press PAUSE button.
6 3 0C 00 Set the data, and press PAUSEbutton.
7 Check that the burst signal level(B) satisfies the specified value.
8 0 01 00 Set the data.
2. S VIDEO OUT Y Level Adjustment (VC-280 Board)
Mode Camera
Subject Arbitrary
Measurement Point Y signal terminal of S VIDEO jack(75Ω terminated)
Measuring Instrument Oscilloscope
Adjustment Page C
Adjustment Address 25
Specified Value A = 1000 ± 14mV
Note: The data of page: 0, address: 10 must be “00”.
Switch setting:DEMO MODE (Menu setting) ................................................OFF
Adjusting method:
Order Page Address Data Procedure
1 0 01 01 Set the data.
2 3 0C 02 Set the data, and press PAUSEbutton.
3 C 25 Change the data and set the Ysignal level (A) to the specifiedvalue.
4 C 25 Press PAUSE button.
5 3 0C 00 Set the data, and press PAUSEbutton.
6 0 01 00 Set the data.
CH1
CH2
A
H
CH1
H
B
When the data of page: 3, address: 0C, is 04:
When the data of page: 3, address: 0C, is 00:
Fig. 5-3-5.
H
Center of luminance line
A
Fig. 5-3-6.
5-49
DCR-TRV16/TRV16E/TRV18/TRV18E/TRV116E/TRV118E
3. S VIDEO OUT Chroma Level Adjustment(VC-280 Board)
Mode Camera
Subject Arbitrary
Measurement Point Chroma signal terminal of S VIDEOjack (75Ω terminated)External trigger: Y signal terminal ofS VIDEO jack
Measuring Instrument Oscilloscope
Adjustment Page C
Adjustment Address 26, 27
Specified Value Cr level: A = 714 ± 14mV (NTSC)A = 700 ± 14mV (PAL)
Cb level:B = 714 ± 14mV (NTSC)B = 700 ± 14mV (PAL)
Burst level: C = 286 ± 6mV (NTSC)C = 300 ± 6mV (PAL)
Note: The data of page: 0, address: 10 must be “00”.
Switch setting:DEMO MODE (Menu setting) ................................................OFF
Adjusting method:
Order Page Address Data Procedure
1 0 01 01 Set the data.
2 3 0C 02 Set the data, and press PAUSEbutton.
3 C 26 Change the data and set the Crsignal level (A) to the specifiedvalue.
4 C 26 Press PAUSE button.
5 C 27 Change the data and set the Cbsignal level (B) to the specifiedvalue.
6 C 27 Press PAUSE button.
7 Check that the burst signal level(C) is satisfied the specified value.
8 3 0C 00 Set the data, and press PAUSEbutton.
9 0 01 00 Set the data.
4. VIDEO OUT Y, Chroma Level Check (VC-280 Board)
Mode Camera
Subject Arbitrary
Measurement Point Video terminal of AUDIO VIDEOjack (75Ω terminated)
Measuring Instrument Oscilloscope
Specified Value Sync level: A = 286 ± 18mV (NTSC)A = 300 ± 18mV (PAL)
Burst level: B = 286 ± 18(mV (NTSC)B = 300 ± 18mV (PAL)
Note: The data of page: 0, address: 10 must be “00”.
Switch setting:DEMO MODE (Menu setting) ................................................OFF
Adjusting method:
Order Page Address Data Procedure
1 3 0C 02 Set the data, and press PAUSEbutton.
2 Check that the sync signal level(A) satisfies the specified value.
3 Check that the burst signal level(B) satisfies the specified value.
4 3 0C 00 Set the data, and press PAUSEbutton.
H
C
A
0.28 µsec (NTSC)0.23 µsec (PAL)
B
0.28 µsec (NTSC) 0.23 µsec (PAL)
H
B
A
Fig. 5-3-7.
Fig. 5-3-8.
5-50
DCR-TRV16/TRV16E/TRV18/TRV18E/TRV116E/TRV118E
3-5. AUDIO SYSTEM ADJUSTMENTS
[Connection of Audio System Measuring Devices]Connect the audio system measuring devices as shown in Fig. 5-3-9.
Fig. 5-3-9.
Recording (Camera mode)
Audio oscillator
Attenuator
600 Ω Left
Right
Main unit
MIC
600 Ω: 270 Ω (1-249-410-11) + 330 Ω (1-249-411-11)
Main unit
AUDIO/VIDEOOUT
Left (White)
Right 47k Ω
47k Ω
Video (Yellow)
TV monitor
Audio level meteror Distortion meter
47k Ω (1-249-437-11)
Playback
(Red)
5-51
DCR-TRV16/TRV16E/TRV18/TRV18E/TRV116E/TRV118E
1. Playback Level Check
Mode VTR playback
Signal Alignment tape:For audio operation check(XH5-3 (NTSC))(XH5-3P (PAL))
Measurement Point Audio left or right terminal of AUDIOVIDEO jack
Measuring Instrument Audio level meter and frequencycounter
Specified Value 32 kHz mode: 1 kHz, +3.0 ± 2.0dBs48 kHz mode: 1 kHz, +3.0 ± 2.0dBs44.1 kHz mode:The 7.35kHz signal level during EMPOFF is +2.0 ± 2.0dBs.The 7.35kHz signal level during EMPON is –6 ± 2 dB from the signal levelduring EMP OFF.
Checking Method:1) Check that the playback signal level is the specified value.
2. Overall Level Characteristics Check
Mode Camera recording and playback
Signal 400Hz, –66 dBs signal: MIC jack leftand right
Measurement Point Audio left or right terminal of AUDIOVIDEO jack
Measuring Instrument Audio level meter
Specified Value –7.5 ± 3.0dBs
Checking Method:1) Input the 400Hz, –66dBs signal in the MIC jack.2) Record in the camera mode.3) Playback the recorded section.4) Check that the 400Hz signal level is the specified value.
3. Overall Distortion Check
Mode Camera recording and playback
Signal 400Hz, –66dBs signal: MIC jack leftand right
Measurement Point Audio left or right terminal of AUDIOVIDEO jack
Measuring Instrument Audio distortion meter
Specified Value Below 0.4%(200Hz to 6kHz BPF ON)
Checking Method:1) Input the 400Hz, –66dBs signal in the MIC jack.2) Record in the camera mode.3) Playback the recorded section.4) Check that the distortion is the specified value.
4. Overall Noise Level Check
Mode Camera recording and playback
Signal No signal: Insert a shorting plug in theMIC jack
Measurement Point Audio left or right terminal of AUDIOVIDEO jack
Measuring Instrument Audio level meter
Specified Value Below –45dBs(IHF-A filter ON, 20kHz LPF ON)
Checking Method:1) Insert a shorting plug in the MIC jack.2) Record in the camera mode.3) Playback the recorded section.4) Check that the noise level is the specified value.
5. Overall Separation Check
Mode Camera recording and playback
Signal 400Hz, –66dBs signal: MIC jack<right> [left](Connect the MIC jack <left> [right]to GND)
Measurement Point Audio <left> [right] terminal ofAUDIO VIDEO jack
Measuring Instrument Audio level meter
Specified Value Below –40dBs (IHF-A filter ON)
< > : Left channel check[ ] : Right channel check
Checking Method:1) Input the 400Hz, –66dBs signal in the <right> [left] terminal
of the MIC jack only.2) Record in the camera mode.3) Playback the recorded section.4) Check that the signal level of the audio <left> [right] terminal
is the specified value.
5-52
DCR-TRV16/TRV16E/TRV18/TRV18E/TRV116E/TRV118E
5-4. SERVICE MODE
4-1. ADJUSTMENT REMOTE COMMANDERThe adjustment remote commander is used for changing thecalculation coefficient in signal processing, EVR data, etc. Theadjustment remote commander performs bi-directionalcommunication with the unit using the remote commander signalline (LANC). The resultant data of this bi-directional communicationis written in the non-volatile memory.
1. Using the adjustment remote commander1) Connect the adjustment remote commander to the LANC
terminal.2) Set the HOLD switch of the adjustment remote commander to
“HOLD” (SERVICE position). If it has been properlyconnected, the LCD on the adjustment remote commander willdisplay as shown in Fig. 5-4-1.
Fig. 5-4-1
3) Operate the adjustment remote commander as follows.• Changing the page
The page increases when the EDIT SEARCH+ button is pressed,and decreases when the EDIT SEARCH– button is pressed.There are altogether 18 pages, from 0 to F, 1B, 1F. (Note)
• Changing the addressThe address increases when the FF (M) button is pressed,and decreases when the REW (m) button is pressed. Thereare altogether 256 addresses, from 00 to FF.
• Changing the data (Data setting)The data increases when the PLAY (N) button is pressed,and decreases when the STOP (x) button is pressed. Thereare altogether 256 data, from 00 to FF.
• Writing the adjustment dataThe PAUSE button must be pressed to write the adjustmentdata (8, A, B, C, D, E, F, 1B, 1F page) in the nonvolatilememory. (The new adjusting data will not be recorded in thenonvolatile memory if this step is not performed.)
4) After completing all adjustments, turn off the main powersupply once.
Note: When reading or writing the 1B, 1F page data, select page: 0,address: 10, and set data: 01, then select B or F page. The 1B or1F page can be chosen by this data setting.After reading or writing, reset the data of page: 0, address: 10to “00”.
HexadecimalnotationLCD DisplayDecimal notationconversion value
0 1 2 3 4 5 6 7 8 9 A B C D E F
0 1 2 3 4 5 6 7 8 9 A b c d E F
0 1 2 3 4 5 6 7 8 9 101112131415
2. Precautions upon usingthe adjustment remote commander
Mishandling of the adjustment remote commander may erase thecorrect adjustment data at times. To prevent this, it is recommendedthat all adjustment data be noted down before beginning adjustmentsand new adjustment data after each adjustment.
Page Data Address
5-53
DCR-TRV16/TRV16E/TRV18/TRV18E/TRV116E/TRV118E
4-2. DATA PROCESSThe calculation of the DDS display and the adjustment remotecommander display data (hexadecimal notation) are required forobtaining the adjustment data of some adjustment items. In this case,after converting the hexadecimal notation to decimal notation,calculate and convert the result to hexadecimal notation, and use itas the adjustment data. Indicates the hexadecimal-decimalconversion table.
Hexadecimal-decimal Conversion TableLower digit ofhexadecimal
Upper digit of hexadecimal
0 1 2 3 4 5 6 7 8 9 A(A)
B(b)
C(c)
D(d)
E(E)
F(F)
0
1
2
3
4
5
6
7
8
9
A (A)
B (b)
C (c)
D (d)
E (E)
F (F)
0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15
16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31
32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47
48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63
64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79
80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95
96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111
112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127
128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143
144 145 146 147 148 149 150 151 152 153 154 155 156 157 158
174
159
175160 161 162 163 164 165 166 167 168 169 170 171 172 173
177176 178 179 180 181 182 183 184 185 186 187 188 189 190 191
192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207
208 209 210 211 212 213 214 215 216 217 218 219 220 221 222 223
224 225 226 227 228 229 230 231 232 233 234 235 236 237 238 239
240 241 242 243 244 245 246 247 248 249 250 251 252 253 254 255
0
1
Note : The characters shown in the parenthesis ( ) shown the display on the adjustment remote commander.(Example) If the DDS display or the adjustment remote commander shows BD (bd);
Because the upper digit of the adjustment number is B (b), and the lower digit is D (d), the meeting point “189” of 1 and 2 in the above table is the corresponding decimal number.
0
2
Table. 5-4-1.
5-54
DCR-TRV16/TRV16E/TRV18/TRV18E/TRV116E/TRV118E
4-3. SERVICE MODE
Note: Before performing the adjustments, check the data of page: 0,address: 10 is “00”. If not, set data: 00 to this address.
1. Setting the Test Mode
Page D Address 10
• Before setting the data , select page: 0, address: 01, and set data:01.
• For page D, the data set is recorded in the non-volatile memoryby pressing the PAUSE button of the adjustment remotecommander. In this case, take note that the test mode will not beexited even when the main power is turned off.
• After completing adjustments/repairs, be sure to return the dataof this address to 00, and press the PAUSE button of the adjustmentremote commander.Select page: 0, address: 01, and set data: 00.
2. Emergence Memory Address
Page C Address F4 to FF
When no error occurs in this unit, data “00” is written in the aboveaddresses (F4 to FF). when first error occurs in the unit, the datacorresponding to the error is written in the first emergency address(F4 to F7). In the same way, when the second error occurs, the datacorresponding to the error is written in the second emergency address(F8 to FB). Finally, when the last error occurs, the data correspondingto the error is written in the last emergency address (FC to FF).
Note: After completing adjustments, be sure to initialize the data ofaddresses F4 to FF to “00”.
Initializing method:1) Select page: 0, address: 01, and set data: 01.2) Select page: 3, address: 01, set data: 37, and press the PAUSE
button.3) Select page: 0, address: 01, and set data: 00.
ContentsEMG code when first error occurs
Upper: MSW code when shift starts when firsterror occursLower: MSW code when first error occurs
Lower: MSW code to be moved when first erroroccurs
EMG code when second error occurs
Upper: MSW code when shift starts when seconderror occursLower: MSW code when second error occurs
Lower: MSW code to be moved when second erroroccurs
EMG code when last error occurs
Upper: MSW code when shift starts when last erroroccursLower: MSW code when last error occurs
Lower: MSW code to be moved when last erroroccurs
AddressF4
F6
F7
F8
FA
FB
FC
FE
FF
2-1. EMG Code (Emergency Code)Codes corresponding to the errors which occur are written inaddresses F4, F8 and FC. The type of error indicated by the codeare shown in the following table.
Emergency TypeNo error
Loading motor emergency during loading
Loading motor emergency during unloading
T reel emergency during normal rotation
S reel emergency during normal rotation
T reel emergency (Short circuit between S reelterminal and T reel terminal)
FG emergency at the start up of the capstan
FG emergency at the start up of the drum
FG emergency during normal rotation of the drum
Code00
10
11
22
23
24
30
40
42
FunctionNormal
Forced camera power ON
Forced VTR power ON
Forced camera + VTR power ON
Forced memory power ON
Data00
01
02
03
05
5-55
DCR-TRV16/TRV16E/TRV18/TRV18E/TRV116E/TRV118E
00
10
=2
11
10
=E
← UNLOAD
Lock releasedCassette compartment
Pinch roller pressing
LS chassis movement section
EJ BL
10
10
=A
11
10
=E
ULE BL
10
00
=8
11
10
=E
SR BL
11
00
=C
11
10
=E
GL BL
01
00
=4
11
10
=E
STOP BL
01
10
=6
R/P
LOAD →
← A (MSB) ← B← C← D (LSB) (Fixed at “0”)
Mechanical Position
Position
EJ
BL
ULE
SR
GL
STOP
R/P
NULL
Code
2
E
A
8
C
4
6
0
F
ContentsPosition at which the cassette component lock is released, at the farthest unload side mechanicallyat which the mechanism can move no further in the UNLOAD direction.
BLANK code, at the boundary between codes.
EJECT completion position. when the cassette is ejected, the mechanism will stop at this position.Cassette IN standby. The guide will start protruding out as the mechanism moves towards theLOAD position.
Position at which it is possible to release the S ratchet.
Guide loading are performed here.
Stop position in the loading state. The pinch roller separates, the tension regulator returns, and thebrake is imposed on both reels.
PB, REC, CUE, REVIEW, PAUSE positions. When pinch roller is pressed, and the tensionregulator is ON, the mechanism is operating at this position in modes in which normal images areshown.
Code not existing in the MD. Default value.
Status before finding any mechanism position.
2-2. MSW CodeMSW when errors occur:Information on MSW (mode SW) when errors occurMSW when movement starts: Information on MSW when movements starts when the mechanism position is moved (When the L motor is moved)MSW of target of movement: Information on target MSW of movement when the mechanism position is moved
5-56
DCR-TRV16/TRV16E/TRV18/TRV18E/TRV116E/TRV118E
Display on theadjustment
remotecommander
0
1
2
3
4
5
6
7
8
9
A (A)
B (b)
C (c)
D (d)
E (E)
F (F)
Bit valuesbit3or
bit70
0
0
0
0
0
0
0
1
1
1
1
1
1
1
1
bit2or
bit60
0
0
0
1
1
1
1
0
0
0
0
1
1
1
1
bit1or
bit50
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
bit0or
bit40
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1B
Example: If “8E” is displayed on the adjustment remote commander, thebit values for bit7 to bit4 are shown in the A column, and thebit values for bit3 to bit0 are shown in the B column.
Page
Address
bit3 to bit0 discrimination
bit7 to bit4 discrimination
Display on the adjustment remote commander
3. Bit value discriminationBit values must be discriminated using the display data of theadjustment remote commander for following items. Use the tablebelow to discriminate if the bit value is “1” or “0”.
A
4. Switch check (1)
Page 7 Address 0E
Note: The data of page: 0, address: 10 must be “00”.
Bit1
2
3
FunctionMIC jack (MA-409 board J5901)
AUDIO/VIDEO jack (JK-217 board J5302)
S VIDEO jack (JK-217 board J5302)
When bit value=1Used
Used
Used
When bit value=0Not used
Not used
Not used
Bit0
1
2
3
4
5
6
7
FunctionPOWER SW (VTR MODE SW) (PS-CX2670 block S001)
POWER SW (CAM MODE SW) (PS-CX2670 block S001)
START/STOP SW (PS-CX2670 block S002)
EJECT SW (FP-443 flexible S201)
CC DOWN SW (Mechanism chassis)
PHOTO FREEZE SW (PS-CX2670 block S071)
POWER SW (PHOTO STBY SW) (PS-CX2670 block S001)
When bit value=1ON (VCR/PLAYER)
ON (CAMERA)
ON
ON
ON (DOWN)
ON
ON (MEMORY)
When bit value=0OFF
OFF
OFF
OFF
OFF (UP)
OFF
OFF
Using method:1) Select page: 7, address: 0E.2) By discriminating the bit value of display data, the state of the switch can be discriminated.
5. Switch check (2)
Page 7 Address 0C
Note: The data of page: 0, address: 10 must be “00”.
Using method:1) Select page: 7, address: 0C.2) By discriminating the bit value of display data, the state of the switch can be discriminated.
5-57
DCR-TRV16/TRV16E/TRV18/TRV18E/TRV116E/TRV118E
6. Switch check (3)
Page 3 Address 61
Note: The data of page: 0, address: 10 must be “00”.
Using method:1) Select page: 3, address: 61.2) By discriminating the bit value of display data, the state of the switch can be discriminated.
Bit6
FunctionHEADPHONS jack (MA-409 board J5902)
When bit value=1Used
When bit value=0Not used
7. Switch check (4)
Page 2 Address 60 to 66
Note: The data of page: 0, address: 10 must be “00”.
Using method:1) Select page: 2, address: 60 to 66.2) By discriminating the display data, the pressed key can be discriminated.
*1: DCR-TRV18/TRV18E/TRV118E
Address
60(KEY AD0)(IC3101 tl)
61(KEY AD1)(IC3101 y;)
62(KEY AD2)(IC3101 ya)
63(KEY AD3)(IC3101 yg)
64(KEY AD4)(IC3101 yh)
65(KEY AD5)(IC3101 yj)
66(KEY AD6)(IC3101 yk)
00(00 to 0C)
PHOTO(PHOTO REC)(PS-CX2670)
(S071)
MPEG PLAY(SH-CX2670)
(S101) *1
PB ZOOM(SH-CX2670)
(S114)
REC(SH-CX2670)
(S106,111)
STOP(CK-108)(S5201)
COLOR SLOWS/ SUPER NS
(JK-218)(S5351)
FADER(FP-444)(S301)
19(0D to 24)
EDITSEARCH +(FP-443)(S202)
MEMORYPLAY
(SH-CX2670)(S102) *1
MENU(SH-CX2670)
(S115)
VOL +(SH-CX2670)
(S110)
REW(CK-108)(S5202)
FOCUS(INFINITY)
(FP-444)(S302)
Data32
(25 to 3F)EDIT
SEARCH –(FP-443)(S203)
MEMORYINDEX
(SH-CX2670)(S107) *1
AUDIO DUB(SH-CX2670)
(S116)
END SEARCH(SH-CX2670)
(S109)
PLAY(CK-108)(S5204)
FOCUS(AUTO/MANUAL)
(FP-444)(S302)
4E(40 to 5D)
MEMORYDELETE
(SH-CX2670)(S112) *1
BACK LIGHT(KP-CX2670)
(S100)
DISPLAY(SH-CX2670)
(S104)
FF(CK-108)(S5205)
6F(5E to 81)
MEMORYMIX
(SH-CX2670)(S113) *1
EXPOSURE(KP-CX2670)
(S101)
VOL –(SH-CX2670)
(S105)
PAUSE(CK-108)(S5206)
96(82 to AA)
MEMORY +(SH-CX2670)
(S108) *1
PANELREVERSE(FP-309)
PANEL CLOSE(CK-108)(S5207)
EXECUTE(KP-CX2670)
(S103)
C1(AB to D7)
MEMORY –(SH-CX2670)
(S103) *1
E8(D8 to FF)
No key input
No key input
PANELNORMAL(FP-309)
PANEL OPEN(CK-108)(S5207)
No key input
No key input
No key input
5-58E
DCR-TRV16/TRV16E/TRV18/TRV18E/TRV116E/TRV118E
8. Record of Use check (1)
Page 7 Address A7 to A9
Note1: When replacing the drum assembly or the mechanism deck, initialize the data of address: A7 to A9.Note2: This data will be kept even if the lithium battery (CK-108 board BT5201 of the cabinet (R) assembly) is removed.Note3: The data of page: 0, address: 10 must be “00”.
Using method:1) The record of use data is displayed at addresses: A7 to A9.
Initializing method:1) Select page: 7, address: 00, and set data: 71.2) Select page: 7, address: 01, set data: 71 and press the PAUSE button.3) Check that the data of page: 7, address: 02 is “00”.
AddressA7
A8
A9
Remarks100000th place digit and 10000th place digit of counted time
1000th place digit and 100th place digit of counted time
10th place digit and 1st place digit of counted time
FunctionHour (H)
Drum rotation counted time (BCD code) Hour (M)
Hour (L)
9. Record of Use check (2)
Page 7 Address C8 to CD
Note1: This data will be kept even if the lithium battery (CK-108 board BT5201 of the cabinet (R) assembly) is removed.Note2: The data of page: 0, address: 10 must be “00”.
Using method:1) The record of use data is displayed at addresses: C8 to CD.
10. Record of Self-diagnosis check
Page 7 Address B0 to C6
AddressC8
C9
CA
CB
CC
CD
Remarks
After setting the clock, set the date of power on next.
FunctionYear
User initial power on date (BCD code) Month
Day
Final condensation occurrence dateYear
(BCD code)Month
Day
Note1: This data will be kept even if the lithium battery (CK-108 boardBT5201 of the cabinet (R) assembly) is removed.
Note2: The data of page: 0, address: 10 must be “00”.
Address Self-diagnosis code
B0 “Repaired by” code (Occurred 1st time) *1
B1 “Block function” code (Occurred 1st time)
B2 “Detailed” code (Occurred 1st time)
B4 “Repaired by” code (Occurred 2nd time) *1
B5 “Block function” code (Occurred 2nd time)
B6 “Detailed” code (Occurred 2nd time)
B8 “Repaired by” code (Occurred 3rd time) *1
B9 “Block function” code (Occurred 3rd time)
BA “Detailed” code (Occurred 3rd time)
BC “Repaired by” code (Occurred 4th time) *1
BD “Block function” code (Occurred 4th time)
BE “Detailed” code (Occurred 4th time)
C0 “Repaired by” code (Occurred 5th time) *1
C1 “Block function” code (Occurred 5th time)
C2 “Detailed” code (Occurred 5th time)
C4 “Repaired by” code (Occurred the last time) *1
C5 “Block function” code (Occurred the last time)
C6 “Detailed” code (Occurred the last time)
*1 : “01” → “C”, “03” → “E”
Using method:1) The past self-diagnosis codes are displayed at addresses: BC
to C6. Refer to “SELF-DIAGNOSIS FUNCTION” for detailof the self-diagnosis code.
6-1
DCR-TRV16/TRV16E/TRV18/TRV18E/TRV116E/TRV118E
SECTION 6REPAIR PARTS LIST
6-1. EXPLODED VIEWSNOTE:• -XX, -X mean standardized parts, so they may
have some differences from the original one.• Items marked “*” are not stocked since they
are seldom required for routine service. Somedelay should be anticipated when ordering theseitems.
• The mechanical parts with no reference numberin the exploded views are not supplied.
• AbbreviationAUS : Australian modelCH : Chinese modelJE : Tourist modelEE : East European modelNE : North European modelHK : Hong Kong model
The components identified by mark 0ordotted line with mark 0 are critical for safety.Replace only with part number specified.
Les composants identifiés par une marque0 sont critiques pour la sécurité.Ne les remplacer que par une pièce portantle numéro spécifié.
COVERCOVER
6-1-1. OVERALL SECTION
Ref. No. Part No. Description Ref. No. Part No. Description
VA-117
A
A
1
1
1
2
3
1
1
1
1
1
4
5
6
7
8
9
12
11
10
3
BT901
Cabinet (L) section(See page 6-7)
Cabinet (R) section(See page 6-3)
EVF section(See page 6-5)
Main chassis complete section(See page 6-6)
Front panel section(See page 6-2)
1 3-056-030-61 SCREW (M1.7), LOCK ACE, P22 X-3950-537-1 CAP ASSY, LENS3 4-974-725-01 SCREW (M1.7X2.5), P4 3-713-791-11 SCREW (M1.7X5), TAPPING, P25 3-067-024-01 BRACKET (LOWER), STRAP
6 X-3952-229-1 BT PANEL ASSY7 3-067-025-01 CPC LID8 X-3952-231-1 TOP CABINET ASSY9 1-684-248-11 FP-434 FLEXIBLE BOARD10 3-073-511-11 PLATE, JACK ORNAMENTAL (TRV16/TRV18)
10 3-073-511-21 PLATE, JACK ORNAMENTAL(TRV16E:AEP,UK,EE,NE/TRV18E:AEP,UK,EE,NE)
10 3-073-511-31 PLATE, JACK ORNAMENTAL(TRV16E:E,HK,AUS,CH/TRV116E/
TRV18E:E,HK,AUS,CH,JE/TRV118E)11 3-073-502-31 SHEET, POWER
(TRV18/TRV18E:E,HK,AUS,CH,JE/TRV118E)11 3-073-502-41 SHEET, POWER (TRV18E:AEP,UK,EE,NE)11 3-073-502-51 SHEET, POWER
(TRV16/TRV16E:E,HK,AUS,CH/TRV116E)11 3-073-502-61 SHEET, POWER (TRV16E:AEP,UK,EE,NE)
12 3-074-433-01 LABEL, COLOR (VF)BT901 1-694-772-11 TERMINAL BOARD, BATTERY
Ver 1.3 2004. 09
6-2
DCR-TRV16/TRV16E/TRV18/TRV18E/TRV116E/TRV118E
6-1-2. FRONT PANEL SECTION
A
A
MIC901
51
52
53
5455
5657
58
59
60
62
63
64
61
5353 64
53
Ref. No. Part No. Description Ref. No. Part No. Description
51 4-974-725-01 SCREW (M1.7X2.5), P52 A-7078-104-A MA-409 BOARD, COMPLETE53 3-713-791-51 SCREW (M1.7X3.5), TAPPING, P254 3-073-464-01 RETAINER, FOCUS BUTTON55 3-073-463-01 FOCUS, BUTTON
56 3-073-460-01 RETAINER (2), MICROPHONE57 3-073-461-01 CUSHION, MICROPHONE RETAINER58 3-073-459-01 RETAINER (1), MICROPHONE
59 3-074-585-01 CUSHION, MICROPHONE60 3-073-462-01 LIGHT, TALLY GUIDE61 A-7078-103-A FB-219 BOARD, COMPLETE62 X-3952-401-1 F PANEL ASSY63 1-684-258-21 FP-444 FLEXIBLE BOARD
64 3-075-386-01 CUSHION, JACKMIC901 1-542-477-11 MICROPHONE
6-3
DCR-TRV16/TRV16E/TRV18/TRV18E/TRV116E/TRV118E
6-1-3. CABINET (R) SECTION
CK-108
B
A
B
A
SP901
ns
101
102103
105
106104
101
113 107
108
109 110
103
103 112
111
LCD section(See page 6-4)
: BT5201 (Lithium battery) CK-108 board on the mount position. (See page 4-80)
ns : not supplied
Ref. No. Part No. Description Ref. No. Part No. Description
CAUTION :Danger of explosion if battery is incorrectly replaced.Replace only with the same or equivalent type.
101 3-055-573-01 SCREW (M1.7), LOCK ACE, P2102 A-7078-105-A CK-108 BOARD, COMPLETE103 3-713-791-51 SCREW (M1.7X3.5), TAPPING, P2104 3-074-072-01 FRAME BOTTOM105 3-055-257-01 TRIPOD (LARGE)
106 3-073-466-01 BLIND, KURUPON107 1-477-147-11 SWITCH BLOCK, CONTROL (KP-CX2670)
* 108 X-3950-471-1 RETAINER ASSY, SPEAKER109 X-3952-407-1 CABINET (R) ASSY 2.5110 3-959-978-02 CUSHION, PANEL
111 1-477-149-21 SWITCH BLOCK, CONTROL (SH-CX2670)(TRV18/TRV18E:E,HK,AUS,CH,JE/TRV118E)
111 1-477-149-31 SWITCH BLOCK, CONTROL (SH-CX2670)(TRV18E:AEP,UK,EE,NE)
111 1-477-149-41 SWITCH BLOCK, CONTROL (SH-CX2670)(TRV16/TRV16E:E,HK,AUS,CH/TRV116E)
111 1-477-149-51 SWITCH BLOCK, CONTROL (SH-CX2670)(TRV16E:AEP,UK,EE,NE)
112 3-074-538-01 RETAINER, P HARNESS
113 3-989-735-91 SCREW (M1.7), LOCK ACE, P2SP901 1-529-590-11 SPEAKER (2.0CM)
6-4
DCR-TRV16/TRV16E/TRV18/TRV18E/TRV116E/TRV118E
6-1-4. LCD SECTION
PD-161
A
B
LCD901
ND901
151
151
152
151
153
154
155
157
158
166
167
159
LCD902
160
163 162
161
153
153156
164
165
A
B
Ref. No. Part No. Description Ref. No. Part No. Description
151 3-056-233-21 SCREW (M2), LOCK ACE, P2152 X-3952-405-1 P CABINET (C) ASSY 2.5153 4-974-725-01 SCREW (M1.7X2.5), P154 3-073-468-01 COVER (FRONT), HINGE155 X-3952-242-1 HINGE ASSY
156 1-684-256-21 FP-442 FLEXIBLE BOARD157 3-073-469-01 COVER (REAR), HINGE158 1-961-795-11 HARNESS (PV-138)159 3-073-488-01 PLATE, P ORNAMENTAL (TRV18)159 3-073-488-11 PLATE, P ORNAMENTAL (TRV18E)
159 3-073-488-21 PLATE, P ORNAMENTAL (TRV16)159 3-073-488-31 PLATE, P ORNAMENTAL (TRV16E)159 3-075-361-01 PLATE, P ORNAMENTAL (TRV116E)
159 3-075-361-11 PLATE, P ORNAMENTAL (TRV118E)160 X-3952-244-1 P FRAME ASSY (2.5)161 3-073-474-01 P CABINET (M) 2.5162 3-073-470-01 BUTTON, P OPEN163 3-073-472-01 SPRING (U), LOCK
164 3-073-471-01 P LOCK165 3-073-473-01 SPRING (L), LOCK166 A-7078-106-A PD-161 (25SH123) BOARD, COMPLETE167 3-073-467-01 LCD HOLDERLCD901 1-803-853-21 INDICATOR MODULE LIQUID CRYST
(LQ25A3FR34)
LCD902 A-7096-989-A INDICATION LCD BLOCK ASSY0ND901 1-518-798-21 TUBE, FLUORESCENT,COLD CATHODE
Note :The components identified bymark 0 or dotted line with mark0 are critical for safety.Replace only with part numberspecified.
Note :Les composants identifiés parune marque 0 sont critiquespour la sécurité.Ne les remplacer que par unepièce portant le numéro spécifié.
6-5
DCR-TRV16/TRV16E/TRV18/TRV18E/TRV116E/TRV118E
6-1-5. EVF SECTION
202
205
206
207208
209211 212
210
213
203
204
201
LCD903
ns
ns
203
ns : not supplied
Ref. No. Part No. Description Ref. No. Part No. Description
201 4-974-725-01 SCREW (M1.7X2.5), P202 3-073-454-01 SHEET, VF FLEXIBLE RETAINER203 3-713-791-31 SCREW (M1.7X6), TAPPING, P2204 X-3952-234-1 VF BASE ASSY205 1-684-249-11 FP-435 FLEXIBLE BOARD
206 A-7078-102-A LB-077 BOARD, COMPLETE207 3-072-214-01 GUIDE (20), LAMP
208 3-072-211-01 ILLUMINATOR209 3-072-210-01 SHEET, PRISM210 X-3952-235-1 VF CABINET (UPPER) ASSY211 3-059-734-01 CUSHION (1), LCD212 X-3952-236-1 VF CABINET (LOWER) ASSY
213 X-3951-453-1 LENS ASSY, VFLCD903 8-753-028-47 LCX032AN-5
6-6
DCR-TRV16/TRV16E/TRV18/TRV18E/TRV116E/TRV118E
6-1-6. MAIN CHASSIS COMPLETE SECTION
VC-280
VA-117
251
255 251
258257
251
251
265
251
261
271
254
256
260
262
259
253
251 272
264
266
268
252 251
269
270
263
273267
IC5001
ns
AB
C
D
A
B C
D
E
F
F
G
G
E
Mechanism deck(See page 6-8 to 6-10)
ns : not supplied
Ref. No. Part No. Description Ref. No. Part No. Description
251 4-974-725-01 SCREW (M1.7X2.5), P252 A-7078-100-A JK-217 BOARD, COMPLETE253 A-7078-101-A JK-218 BOARD, COMPLETE254 3-713-791-51 SCREW (M1.7X3.5), TAPPING, P2255 3-073-432-01 FRAME (960), LENS
256 1-815-124-11 CONNECTOR, EXTERNAL (HOT SHOE)(TRV18/TRV18E/TRV118E)
256 1-815-124-21 CONNECTOR, EXTERNAL (HOT SHOE)(TRV16/TRV16E/TRV116E)
257 3-074-612-01 CUSHION, SENSOR PROTECTION258 8-848-748-01 DEVICE, LENS LSV-650D259 3-059-722-01 COVER, CASSETTE COMPARTMENT
260 X-3952-233-1 MD FRAME ASSY261 3-059-718-01 SCREW (M1.4X1.5)262 1-684-250-11 FP-436 FLEXIBLE BOARD263 3-059-725-01 LABEL, LS264 A-7078-154-A VC-280 (F) BOARD, COMPLETE (SERVICE)
(TRV18/TRV18E:E,HK,AUS,CH,JE/TRV118E)
264 A-7078-277-A VC-280 (O) BOARD, COMPLETE (SERVICE)(TRV16E:AEP,UK,EE,NE)
264 A-7078-278-A VC-280 BOARD, COMPLETE (SERVICE)(TRV16/TRV16E:E,HK,AUS,CH/TRV116E)
264 A-7078-279-A VC-280 (FO) BOARD, COMPLETE (SERVICE)(TRV18E:AEP,UK,EE,NE)
265 3-074-613-01 VV SHIELD SHEET266 A-7078-099-A VA-117 (F) BOARD, COMPLETE
(TRV18/TRV18E/TRV118E)266 A-7078-162-A VA-117 MOUNT BOARD, COMPLETE
(TRV16/TRV16E/TRV116E)
267 1-758-155-21 FILTER BLOCK, OPTICAL (OFB-04-14)268 1-684-253-11 FP-439 FLEXIBLE BOARD269 1-684-251-11 FP-437 FLEXIBLE BOARD270 1-684-259-11 FP-445 FLEXIBLE BOARD271 3-713-791-41 SCREW (M1.7X5), TAPPING, P2
272 A-7078-107-A CD-365 BOARD, COMPLETE273 3-053-973-01 RUBBER (W), SEALIC5001 A-7031-244-A CCD BLOCK ASSY (CCD IMAGER)
(TRV16/TRV18)IC5001 A-7031-276-A CCD BLOCK ASSY (CCD IMAGER)
(TRV16E/TRV116E/TRV18E/TRV118E)
6-7
DCR-TRV16/TRV16E/TRV18/TRV18E/TRV116E/TRV118E
6-1-7. CABINET (L) SECTIONns : not supplied
A
B
B
A301
302303
304
306
307
308
309
305
304
304
304
316
302
318
319317
304
310311
312
314
315
313
313
317
ns
ns
ns
313
TRV18/TRV18E/TRV118E
TRV18/TRV18E/TRV118E
Ref. No. Part No. Description Ref. No. Part No. Description
301 X-3952-237-1 LOCK ASSY, GRIP302 3-989-735-91 SCREW (M1.7), LOCK ACE, P2303 X-3952-414-1 CABINET (L) ASSY (TRV18)303 X-3952-415-1 CABINET (L) ASSY (TRV18E/TRV118E)303 X-3952-417-1 CABINET (L) ASSY (TRV16E/TRV116E)
303 X-3952-418-1 CABINET (L) ASSY (TRV16)304 3-713-791-11 SCREW (M1.7X5), TAPPING, P2305 3-074-586-01 CUSHION (2), MUFFLE
* 306 3-055-189-01 FOOT (A)307 3-061-550-01 BELT, GRIP
308 1-684-257-21 FP-443 FLEXIBLE BOARD309 X-3952-230-1 COVER ASSY, JACK
310 3-073-456-01 EJECT KNOB311 1-684-252-11 FP-438 FLEXIBLE BOARD
(TRV18/TRV18E/TRV118E)312 1-477-148-11 SWITCH BLOCK, CONTROL (PS-CX2670)313 3-713-791-51 SCREW (M1.7X3.5), TAPPING, P2314 X-3952-238-1 CS FRAME ASSY
315 1-816-271-11 CONNECTOR, MEMORY STICK 10P(TRV18/TRV18E/TRV118E)
316 3-073-457-01 COVER, GRIP (TRV18/TRV18E/TRV118E)317 4-974-725-01 SCREW (M1.7X2.5), P318 3-073-458-01 COVER, ZOOM319 3-073-928-01 L SHEET
6-8
DCR-TRV16/TRV16E/TRV18/TRV18E/TRV116E/TRV118E
6-1-8. CASSETTE COMPARTMENT AND DRUM BLOCK ASSEMBLY
703
704
M901
705
706701
708
701
707
701
702
708
710
709
713
711
711
712
LS chassis block assembly(See page 6-9)
Mechanism chassis block assembly(See page 6-10)
Ref. No. Part No. Description Ref. No. Part No. Description
701 3-703-816-14 SCREW (M1.4)702 X-3952-017-3 CASSETTE COMPARTMENT ASSY703 3-059-082-01 SPRING, TENSION
(CASSETTE COMPARTMENT S)704 3-059-208-01 SPRING (CASSETTE COMPARTMENT T)705 X-3950-370-3 DAMPER ASSY
706 3-059-101-03 RETAINER, LS GUIDE707 7-624-102-04 STOP RING 1.5, TYPE -E
708 3-704-197-21 SCREW (M1.4X2.5), SPECIAL HEAD709 X-3950-364-1 GEAR ASSY, GOOSENECK710 X-3950-366-1 TABLE ASSY, T REEL711 3-075-097-01 SCREW (M1.4X1.4), SPECIAL HEAD712 3-059-093-01 RETAINER, LED
713 X-3950-361-1 PLATE ASSY, RETAINERM901 A-7048-940-A DRUM (DEH-18A-R)
6-9
DCR-TRV16/TRV16E/TRV18/TRV18E/TRV116E/TRV118E
6-1-9. LS CHASSIS BLOCK ASSEMBLY
753
754
755
756
757758
760759
761762
763
764765
766
D901
Q901
770
767
768769
S903
Q902H901
H902
nsns
ns
ns
752
751
FP-102
Note: FP-102 is included in the LS sub assy and is attached to chassis by hot-press. Because installation of FP-102 requires a very high accuracy, FP-102 is not supplied as an independent service parts.
Note
ns : not supplied
Ref. No. Part No. Description Ref. No. Part No. Description
751 3-059-173-01 PLATE, LS CAM752 3-075-097-01 SCREW (M1.4X1.4), SPECIAL HEAD753 X-3950-371-1 ARM ASSY, BRAKE (S) DRIVING754 3-059-166-01 BRAKE (S)755 3-059-146-01 POSITIONING (S), CASSETTE
756 3-059-167-01 SPRING (BRAKE S), TENSION COIL757 3-059-169-01 SPRING (BRAKE S ARM), TORSION758 3-703-816-14 SCREW (M1.4)759 3-059-090-01 SCREW (M1.4X2.5), SPECIAL HEAD
* 760 X-3950-358-4 TG1 ASSY
761 3-059-156-01 SPRING (TENSION REGULATOR)762 X-3950-365-2 TABLE ASSY, S REEL763 A-7094-819-A TG7 BLOCK ASSY
764 3-059-165-01 SPRING (TG7 RETURN), TORSION765 X-3950-359-1 ARM ASSY, PINCH766 3-059-161-01 SPRING (PINCH RETURN), TORSION767 3-059-170-01 BRAKE (T)768 3-059-171-01 GEAR (T), BRAKE
769 3-059-172-01 SPRING (T), BRAKE770 A-7094-816-B LS BLOCK ASSYD901 8-719-078-71 DIODE LA57A, SO (TAPE LED)H901 8-719-067-74 ELEMENT, HOLE HW-105A-CDE-T (S REEL)H902 8-719-067-74 ELEMENT, HOLE HW-105A-CDE-T (T REEL)
Q901 8-729-028-71 TRANSISTOR PN166, SO (TAPE END)Q902 8-729-028-71 TRANSISTOR PN166, SO (TAPE TOP)S903 1-572-288-11 SWITCH, PUSH (C.C.DOWN)
6-10
DCR-TRV16/TRV16E/TRV18/TRV18E/TRV116E/TRV118E
6-1-10. MECHANISM CHASSIS BLOCK ASSEMBLYns : not supplied
801
802
803
804
806
829
805
807
808
M903
812
811
813 820
815
824
807
815
826
815
827
828
815
825
818
819
817
815
822
814
810
809
815816
830
ns
821 823
ns
M902 (Including belt)
Ref. No. Part No. Description Ref. No. Part No. Description
801 3-059-211-01 GEAR, CONVERSION802 3-059-220-01 GEAR, RELAY803 3-059-187-01 SHAFT, WORM804 3-059-186-03 HOLDER, MOTOR805 3-060-002-01 ROLLER, LS GUIDE
806 3-059-189-01 GEAR (A), CAM807 3-704-197-21 SCREW (M1.4X2.5), SPECIAL HEAD808 3-059-225-01 SHIELD, MOTOR809 3-059-191-01 ROLLER, LS810 3-059-190-01 ARM, LS
811 1-677-049-11 FP-228 FLEXIBLE BOARD (DEW SENSOR)812 1-677-084-11 FP-100 FLEXIBLE BOARD813 3-059-149-01 SLIDER, TG1 CAM814 3-059-148-01 ARM, TG1 DRIVING815 3-703-816-14 SCREW (M1.4)
816 3-059-117-01 COVER (A), GEAR817 X-3950-367-1 GEAR ASSY, MODE
818 3-059-139-01 GEAR, GL DRIVING819 3-059-188-01 GEAR, DECELERATION820 A-7094-818-A COASTER (S) BLOCK ASSY821 A-7094-817-A COASTER (T) BLOCK ASSY822 3-059-126-01 RAIL, GUIDE
823 3-962-914-01 SCREW (M1.4X2)824 A-7094-822-A DRUM BASE BLOCK ASSY825 3-059-118-01 COVER (B), GEAR826 3-059-083-01 COVER (C), GEAR827 X-3950-368-1 ARM ASSY, PINCH DRIVING
828 3-059-192-01 GEAR (B), CAM829 3-063-355-01 ROLLER (S1), LS GUIDE830 3-065-202-01 SUPPORT, TG7M902 8-835-685-01 MOTOR, DC SCD18A/C-NP (INCLUDING BELT)
(CAPSTAN)M903 A-7094-823-A MOTOR BLOCK ASSY, L
6-11
Ref. No. Part No. Description Ref. No. Part No. Description
DCR-TRV16/TRV16E/TRV18/TRV18E/TRV116E/TRV118E
6-2. ELECTRICAL PARTS LISTNOTE:• Due to standardization, replacements in the
parts list may be different from the partsspecified in the diagrams or the componentsused on the set.
• -XX, -X mean standardized parts, so they mayhave some difference from the original one.
• Items marked “*” are not stocked since theyare seldom required for routine service. Somedelay should be anticipated when ordering theseitems.
• CAPACITORS:uF: µF
• COILSuH: µH
• RESISTORSAll resistors are in ohms.METAL: metal-film resistorMETAL OXIDE: Metal Oxide-film resistorF: nonflammable
• SEMICONDUCTORSIn each case, u: µ, for example:uA...: µA... , uPA... , µPA... ,uPB... , µPB... , uPC... , µPC... ,uPD..., µPD...
• AbbreviationCND : Canadian modelAUS : Australian modelCH : Chinese modelJE : Tourist model
When indicating parts by reference number,please include the board name.
The components identified by mark 0 ordotted line with mark 0 are critical for safety.Replace only with part number specified.
Les composants identifiés par une marque0 sont critiques pour la sécurité.Ne les remplacer que par une pièce portantle numéro spécifié.
EE : East European modelNE : North European modelHK : Hong Kong modelKR : Korea model
A-7078-107-A CD-365 BOARD, COMPLETE**********************(IC5001 is not included in this complte board.)
< CAPACITOR >
C5001 1-104-851-11 TANTAL. CHIP 10uF 20% 10VC5002 1-162-915-11 CERAMIC CHIP 10PF 0.5PF 50VC5003 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25VC5004 1-113-985-11 TANTAL. CHIP 10uF 20% 20V
< CONNECTOR >
CN5001 1-815-315-11 CONNECTOR, FFC/FPC 16PCN5002 1-766-336-21 CONNECTOR, FFC/FPC 6P
< IC >
IC5001 A-7031-244-A CCD BLOCK ASSY (CCD IMAGER)(TRV16/TRV18)
IC5001 A-7031-276-A CCD BLOCK ASSY (CCD IMAGER)(TRV16E/TRV116E/TRV18E/TRV118E)
< COIL >
L5001 1-414-406-11 INDUCTOR 220uH
< TRANSISTOR >
Q5001 8-729-117-73 TRANSISTOR 2SC4178-F13F14-T1
< RESISTOR >
R5001 1-216-827-11 METAL CHIP 3.3K 5% 1/16W************************************************************
A-7078-105-A CK-108 BOARD, COMPLETE**********************
< BATTERY >
BT5201 1-756-128-11 BATTERY, LITHIUM (SECONDARY)
< CONNECTOR >
CN5201 1-573-927-11 CONNECTOR, FFC/FPC 18PCN5202 1-815-231-11 CONNECTOR, FFC/FPC (ZIF) 40PCN5203 1-794-997-11 PIN, CONNECTOR 20PCN5204 1-794-377-21 PIN, CONNECTOR 8PCN5205 1-778-506-21 PIN, CONNECTOR (PC BOARD) 2P
CN5207 1-691-346-11 CONNECTOR, FFC/FPC (ZIF) 8P
< DIODE >
D5201 8-719-062-16 DIODE 01ZA8.2(TPL3)D5203 8-719-056-85 DIODE UDZSTE-178.2BD5204 8-719-062-16 DIODE 01ZA8.2(TPL3)D5205 8-719-062-16 DIODE 01ZA8.2(TPL3)D5206 8-719-062-16 DIODE 01ZA8.2(TPL3)
< RESISTOR >
R5201 1-218-953-11 RES-CHIP 1K 5% 1/16WR5206 1-218-954-11 RES-CHIP 1.2K 5% 1/16WR5207 1-218-954-11 RES-CHIP 1.2K 5% 1/16WR5208 1-218-954-11 RES-CHIP 1.2K 5% 1/16WR5209 1-218-954-11 RES-CHIP 1.2K 5% 1/16W
R5210 1-218-955-11 RES-CHIP 1.5K 5% 1/16WR5211 1-218-955-11 RES-CHIP 1.5K 5% 1/16WR5212 1-218-955-11 RES-CHIP 1.5K 5% 1/16WR5213 1-218-955-11 RES-CHIP 1.5K 5% 1/16WR5214 1-218-957-11 RES-CHIP 2.2K 5% 1/16W
R5215 1-218-957-11 RES-CHIP 2.2K 5% 1/16WR5216 1-218-957-11 RES-CHIP 2.2K 5% 1/16WR5217 1-218-957-11 RES-CHIP 2.2K 5% 1/16WR5218 1-218-960-11 RES-CHIP 3.9K 5% 1/16WR5219 1-218-960-11 RES-CHIP 3.9K 5% 1/16W
R5220 1-218-960-11 RES-CHIP 3.9K 5% 1/16WR5221 1-218-964-11 RES-CHIP 8.2K 5% 1/16WR5222 1-218-960-11 RES-CHIP 3.9K 5% 1/16WR5223 1-218-964-11 RES-CHIP 8.2K 5% 1/16WR5224 1-218-964-11 RES-CHIP 8.2K 5% 1/16W
R5225 1-218-970-11 RES-CHIP 27K 5% 1/16WR5226 1-218-964-11 RES-CHIP 8.2K 5% 1/16WR5227 1-218-990-11 SHORT CHIP 0R5228 1-218-990-11 SHORT CHIP 0
< SWITCH >
S5201 1-786-157-11 SWITCH, TACTILE (STOP)S5202 1-786-157-11 SWITCH, TACTILE (REW)S5203 1-786-157-11 SWITCH, TACTILE (RESET)S5204 1-786-157-11 SWITCH, TACTILE (PLAY)S5205 1-786-157-11 SWITCH, TACTILE (FF)
S5206 1-786-157-11 SWITCH, TACTILE (PAUSE)S5207 1-786-148-11 SWITCH, PUSH (1 KEY) (PANEL OPEN/CLOSE)
************************************************************
Be sure to read “Precautions upon replacing CCD imager”on page 4-9 when changing the CCD imager.
CD-365 CK-108
6-12
Ref. No. Part No. Description Ref. No. Part No. Description
DCR-TRV16/TRV16E/TRV18/TRV18E/TRV116E/TRV118E
A-7078-103-A FB-219 BOARD, COMPLETE**********************
< CONNECTOR >
CN6001 1-779-327-11 CONNECTOR, FFC/FPC 6P
< DIODE >
D6001 8-719-074-30 DIODE SML-310LTT86
< PHOTO INTERRUPTER >
PH6001 8-749-016-83 IC GP1S092HCPIPH6002 8-749-016-83 IC GP1S092HCPI
< RESISTOR >
R6001 1-218-990-11 SHORT CHIP 0R6002 1-218-951-11 RES-CHIP 680 5% 1/16WR6003 1-218-947-11 RES-CHIP 330 5% 1/16W
************************************************************
A-7078-100-A JK-217 BOARD, COMPLETE**********************
< CONNECTOR >
CN5305 1-779-334-11 CONNECTOR, FFC/FPC 20P
< DIODE >
D5301 8-719-056-85 DIODE UDZSTE-178.2BD5302 8-719-062-16 DIODE 01ZA8.2(TPL3)
< FERRITE BEAD >
FB5301 1-500-444-11 FERRITE 0uHFB5302 1-469-179-21 FERRITE 0uHFB5303 1-469-179-21 FERRITE 0uHFB5304 1-469-179-21 FERRITE 0uHFB5305 1-469-179-21 FERRITE 0uH
FB5307 1-500-444-11 FERRITE 0uHFB5308 1-500-444-11 FERRITE 0uHFB5309 1-500-444-11 FERRITE 0uHFB5310 1-500-444-11 FERRITE 0uH
< JACK >
J5301 1-793-995-11 JACK, SUPER SMALL TYPE (LANC)J5302 1-694-651-11 TERMINAL BOARD (S VIDEO/AUDIO/VIDEO)
< RESISTOR >
R5301 1-216-864-11 METAL CHIP 0 5% 1/16WR5302 1-216-864-11 METAL CHIP 0 5% 1/16WR5303 1-216-864-11 METAL CHIP 0 5% 1/16WR5304 1-216-864-11 METAL CHIP 0 5% 1/16WR5305 1-216-864-11 METAL CHIP 0 5% 1/16W
< SENSOR >
SE5301 1-803-042-31 SENSOR, ANGULAR VELOCITY (YAW)SE5302 1-803-042-41 SENSOR, ANGULAR VELOCITY (PITCH)
< VARISTOR >
VD5301 1-803-974-21 VARISTOR, CHIPVD5302 1-801-923-11 VARISTOR, CHIPVD5303 1-803-974-21 VARISTOR, CHIPVD5304 1-803-974-21 VARISTOR, CHIPVD5305 1-803-974-21 VARISTOR, CHIP
VD5306 1-803-974-21 VARISTOR, CHIP************************************************************
A-7078-101-A JK-218 BOARD, COMPLETE**********************
< CONNECTOR >
CN5351 1-794-962-11 CONNECTOR, SQUARE TYPE(USB 5P) (USB)CN5352 1-794-276-11 CONNECTOR, SQUARE TYPE 4P (DV IN/OUT)CN5353 1-779-330-21 CONNECTOR, FFC/FPC 12P
< DIODE >
D5351 8-719-062-16 DIODE 01ZA8.2(TPL3)D5352 8-719-056-85 DIODE UDZSTE-178.2BD5353 8-719-056-85 DIODE UDZSTE-178.2BD5354 8-719-078-02 DIODE 1SS357(T3SONY1)
< LINE FILTER >
LF5351 1-419-100-21 INDUCTOR 0uHLF5352 1-419-100-21 INDUCTOR 0uH
< RESISTOR >
R5351 1-218-965-11 RES-CHIP 10K 5% 1/16WR5352 1-218-965-11 RES-CHIP 10K 5% 1/16W
< SWITCH >
S5351 1-786-227-21 SWITCH, TACTILE (SUPER NS)************************************************************
A-7078-102-A LB-077 BOARD, COMPLETE**********************
< CAPACITOR >
C6101 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10VC6102 1-164-505-11 CERAMIC CHIP 2.2uF 16V
< CONNECTOR >
CN6101 1-691-358-21 CONNECTOR, FFC/FPC (ZIF) 20PCN6102 1-691-354-21 CONNECTOR, FFC/FPC (ZIF) 16P
< DIODE >
D6102 8-719-082-33 DIODE NSCW100-T39
< IC >
IC6101 8-759-581-11 IC NJM2125F(TE2)
< TRANSISTOR >
Q6101 8-729-054-48 TRANSISTOR RN4983FE(TPLR3)Q6102 8-729-054-48 TRANSISTOR N1B04FE-Y/GR(TPLR3)
FB-219 JK-217 JK-218 LB-077
6-13
Ref. No. Part No. Description Ref. No. Part No. Description
DCR-TRV16/TRV16E/TRV18/TRV18E/TRV116E/TRV118E
< RESISTOR >
R6102 1-208-941-11 METAL CHIP 180K 0.5% 1/16WR6103 1-208-719-11 METAL CHIP 33K 0.5% 1/16WR6104 1-218-959-11 RES-CHIP 3.3K 5% 1/16WR6105 1-216-839-11 METAL CHIP 33K 5% 1/16WR6106 1-211-977-11 METAL CHIP 22 0.5% 1/10W
< THERMISTOR >
TH6101 1-810-811-11 THERMISTOR, NTC (1608)************************************************************
A-7078-104-A MA-409 BOARD, COMPLETE**********************
< CAPACITOR >
C5901 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25VC5902 1-117-919-11 TANTAL. CHIP 10uF 20% 6.3V
< CONNECTOR >
CN5901 1-816-232-11 PIN, CONNECTOR (PC BOARD) 4PCN5902 1-779-336-11 CONNECTOR, FFC/FPC 24PCN5903 1-779-328-21 CONNECTOR, FFC/FPC 8P
< DIODE >
D5901 8-719-067-44 DIODE CL-310IRS-X-TUD5902 8-719-067-44 DIODE CL-310IRS-X-TUD5903 8-719-073-01 DIODE MA111-(K8).S0D5905 8-719-056-85 DIODE UDZSTE-178.2B
< FERRITE BEAD >
FB5901 1-500-444-11 FERRITE 0uHFB5902 1-500-444-11 FERRITE 0uHFB5903 1-500-444-11 FERRITE 0uHFB5904 1-500-444-11 FERRITE 0uH
< IC >
IC5901 8-742-221-00 HYB IC SBX3055-01
< JACK >
J5901 1-691-737-41 JACK (SMALL TYPE) (MIC(PLUG IN POWER))J5902 1-569-950-41 JACK (SMALL TYPE) (HEADPHONES)
< RESISTOR >
R5901 1-216-805-11 METAL CHIP 47 5% 1/16W
< VARISTOR >
VD5901 1-801-862-11 VARISTOR, CHIPVD5902 1-801-862-11 VARISTOR, CHIPVD5903 1-801-862-11 VARISTOR, CHIPVD5904 1-801-862-11 VARISTOR, CHIP
************************************************************
A-7078-106-A PD-161 (25SH123) BOARD, COMPLETE*******************************
< CAPACITOR >
C5501 1-117-920-11 TANTAL. CHIP 10uF 20% 6.3VC5504 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16VC5505 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16VC5506 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16VC5507 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16V
C5508 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10VC5509 1-135-177-21 TANTALUM CHIP 1uF 20% 20VC5510 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16VC5511 1-164-739-11 CERAMIC CHIP 560PF 5% 50VC5512 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V
C5513 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16VC5514 1-117-920-11 TANTAL. CHIP 10uF 20% 6.3VC5515 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50VC5516 1-164-870-11 CERAMIC CHIP 68PF 5% 50VC5517 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V
C5518 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16VC5519 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16VC5520 1-131-615-11 TANTAL. CHIP 6.8uF 20% 16VC5521 1-127-573-11 CERAMIC CHIP 1uF 10% 16VC5524 1-127-573-11 CERAMIC CHIP 1uF 10% 16V
C5527 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16VC5528 1-135-177-21 TANTALUM CHIP 1uF 20% 20VC5530 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16VC5531 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16VC5603 1-164-657-11 CERAMIC CHIP 0.015uF 10% 50V
C5604 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10VC5605 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V
0C5606 1-131-959-91 CERAMIC CHIP 12PF 10% 3KVC5607 1-115-566-11 CERAMIC CHIP 4.7uF 10% 10V
< CONNECTOR >
CN5501 1-573-364-11 CONNECTOR, FFC/FPC 24PCN5601 1-764-709-11 CONNECTOR, FFC/FPC (LIF) 10PCN5651 1-794-377-21 PIN, CONNECTOR 8PCN5652 1-794-997-11 PIN, CONNECTOR 20PCN5653 1-691-370-11 CONNECTOR, FFC/FPC 6P
CN5654 1-691-384-11 CONNECTOR, FFC/FPC 20P
< DIODE >
D5502 8-719-084-47 DIODE 1SV290(TPL3)D5503 8-719-073-01 DIODE MA111-(K8).S0D5601 8-719-073-01 DIODE MA111-(K8).S0D5602 8-719-062-44 DIODE PG1112H-TR
< FERRITE BEAD >
FB5501 1-414-760-21 FERRITE 0uHFB5502 1-414-760-21 FERRITE 0uHFB5503 1-414-760-21 FERRITE 0uH
Note :The components identified bymark 0 or dotted line with mark0 are critical for safety.Replace only with part numberspecified.
Note :Les composants identifiés parune marque 0 sont critiquespour la sécurité.Ne les remplacer que par unepièce portant le numéro spécifié.
LB-077 MA-409 PD-161
6-14
Ref. No. Part No. Description Ref. No. Part No. Description
DCR-TRV16/TRV16E/TRV18/TRV18E/TRV116E/TRV118E
< IC >
IC5501 8-752-102-40 IC CXA3592R-T4IC5502 8-759-714-77 IC LZ9FF474IC5601 8-759-564-49 IC TC7W53FU(TE12R)IC5602 8-759-075-70 IC TA75S393F-TE85RIC5651 8-759-573-02 IC BU9735K-E2
< COIL >
L5501 1-469-555-21 INDUCTOR 10uHL5503 1-469-891-21 INDUCTOR 6.8uHL5601 1-428-878-11 INDUCTOR 0uH
< TRANSISTOR >
Q5502 8-729-041-23 TRANSISTOR MGSF1P02LT1Q5503 8-729-054-48 TRANSISTOR N1B04FE-Y/GR(TPLR3)Q5504 8-729-054-48 TRANSISTOR N1B04FE-Y/GR(TPLR3)Q5505 8-729-042-29 TRANSISTOR RN1104F(TPL3)Q5601 8-729-042-29 TRANSISTOR RN1104F(TPL3)
Q5603 8-729-054-48 TRANSISTOR RN4983FE(TPLR3)Q5605 6-550-065-01 TRANSISTOR CPH5504-TL-E
< RESISTOR >
R5501 1-218-985-11 RES-CHIP 470K 5% 1/16WR5503 1-208-931-11 METAL CHIP 68K 0.5% 1/16WR5505 1-218-967-11 RES-CHIP 15K 5% 1/16WR5506 1-218-958-11 RES-CHIP 2.7K 5% 1/16WR5507 1-218-973-11 RES-CHIP 47K 5% 1/16W
R5508 1-218-975-11 RES-CHIP 68K 5% 1/16WR5509 1-218-969-11 RES-CHIP 22K 5% 1/16WR5510 1-218-975-11 RES-CHIP 68K 5% 1/16WR5511 1-218-989-11 RES-CHIP 1M 5% 1/16WR5512 1-218-977-11 RES-CHIP 100K 5% 1/16W
R5513 1-218-989-11 RES-CHIP 1M 5% 1/16WR5515 1-218-990-11 SHORT CHIP 0R5516 1-218-965-11 RES-CHIP 10K 5% 1/16WR5519 1-218-990-11 SHORT CHIP 0R5521 1-218-973-11 RES-CHIP 47K 5% 1/16W
R5523 1-218-990-11 SHORT CHIP 0R5531 1-218-980-11 RES-CHIP 180K 5% 1/16WR5532 1-218-977-11 RES-CHIP 100K 5% 1/16WR5533 1-218-989-11 RES-CHIP 1M 5% 1/16WR5534 1-218-953-11 RES-CHIP 1K 5% 1/16W
R5540 1-218-977-11 RES-CHIP 100K 5% 1/16WR5541 1-218-977-11 RES-CHIP 100K 5% 1/16WR5552 1-218-957-11 RES-CHIP 2.2K 5% 1/16WR5591 1-218-953-11 RES-CHIP 1K 5% 1/16WR5601 1-216-055-00 METAL CHIP 1.8K 5% 1/10W
R5602 1-218-980-11 RES-CHIP 180K 5% 1/16WR5603 1-218-969-11 RES-CHIP 22K 5% 1/16WR5605 1-218-942-11 RES-CHIP 120 5% 1/16WR5606 1-218-969-11 RES-CHIP 22K 5% 1/16WR5607 1-218-949-11 RES-CHIP 470 5% 1/16W
R5612 1-218-965-11 RES-CHIP 10K 5% 1/16WR5613 1-218-965-11 RES-CHIP 10K 5% 1/16WR5651 1-218-946-11 RES-CHIP 270 5% 1/16WR5652 1-218-987-11 RES-CHIP 680K 5% 1/16W
< COMPOSITION CIRCUIT BLOCK >
RB5501 1-234-372-21 RES, NETWORK 100X4 (1005)RB5502 1-234-384-11 RES, NETWORK 1MX4 (1005)RB5503 1-234-378-21 RES, NETWORK 10KX4 (1005)
< TRANSFORMER >
0T5601 1-435-786-31 TRANSFORMER, INVERTER
< VARISTOR >
VD5651 1-801-862-11 VARISTOR, CHIP************************************************************
A-7078-099-A VA-117 (F) BOARD, COMPLETE(TRV18/TRV18E/TRV118E)
**************************************A-7078-162-A VA-117 BOARD, COMPLETE
(TRV16/TRV16E/TRV116E)**************************************
< CAPACITOR >
C4001 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10VC4002 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V
(TRV18/TRV18E/TRV118E)C4003 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10VC4101 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16VC4103 1-164-677-11 CERAMIC CHIP 0.033uF 10% 16V
C4104 1-115-467-11 CERAMIC CHIP 0.22uF 10% 10VC4105 1-125-837-91 CERAMIC CHIP 1uF 10% 6.3VC4106 1-125-837-91 CERAMIC CHIP 1uF 10% 6.3VC4107 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16VC4108 1-125-838-11 CERAMIC CHIP 2.2uF 10% 6.3V
C4109 1-125-838-11 CERAMIC CHIP 2.2uF 10% 6.3VC4110 1-125-838-11 CERAMIC CHIP 2.2uF 10% 6.3VC4111 1-135-259-11 TANTAL. CHIP 10uF 20% 6.3VC4112 1-125-837-91 CERAMIC CHIP 1uF 10% 6.3VC4113 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16V
C4114 1-125-837-91 CERAMIC CHIP 1uF 10% 6.3VC4115 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16VC4116 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10VC4117 1-125-838-11 CERAMIC CHIP 2.2uF 10% 6.3VC4118 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16V
C4119 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16VC4120 1-125-899-11 TANTAL. CHIP 220uF 20% 4VC4121 1-125-838-11 CERAMIC CHIP 2.2uF 10% 6.3VC4122 1-125-899-11 TANTAL. CHIP 220uF 20% 4VC4123 1-135-259-11 TANTAL. CHIP 10uF 20% 6.3V
C4125 1-164-858-11 CERAMIC CHIP 22PF 5% 50VC4201 1-115-566-11 CERAMIC CHIP 4.7uF 10% 10VC4204 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16VC4205 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16VC4206 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16V
C4208 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16VC4209 1-164-739-11 CERAMIC CHIP 560PF 5% 50VC4210 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10VC4211 1-131-861-91 TANTAL. CHIP 4.7uF 20% 20VC4212 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V
Note :The components identified bymark 0 or dotted line with mark0 are critical for safety.Replace only with part numberspecified.
Note :Les composants identifiés parune marque 0 sont critiquespour la sécurité.Ne les remplacer que par unepièce portant le numéro spécifié.
PD-161 VA-117
6-15
Ref. No. Part No. Description Ref. No. Part No. Description
DCR-TRV16/TRV16E/TRV18/TRV18E/TRV116E/TRV118E
C4213 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16VC4214 1-164-876-11 CERAMIC CHIP 120PF 5% 50VC4215 1-125-837-91 CERAMIC CHIP 1uF 10% 6.3VC4216 1-125-837-91 CERAMIC CHIP 1uF 10% 6.3VC4217 1-125-837-91 CERAMIC CHIP 1uF 10% 6.3V
C4218 1-109-994-11 CERAMIC CHIP 2.2uF 10% 10VC4219 1-164-505-11 CERAMIC CHIP 2.2uF 16VC4302 1-125-837-91 CERAMIC CHIP 1uF 10% 6.3VC4303 1-125-837-91 CERAMIC CHIP 1uF 10% 6.3VC4304 1-125-837-91 CERAMIC CHIP 1uF 10% 6.3V
C4305 1-135-259-11 TANTAL. CHIP 10uF 20% 6.3VC4306 1-125-837-91 CERAMIC CHIP 1uF 10% 6.3VC4307 1-125-837-91 CERAMIC CHIP 1uF 10% 6.3VC4308 1-125-837-91 CERAMIC CHIP 1uF 10% 6.3VC4309 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V
C4310 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10VC4311 1-135-259-11 TANTAL. CHIP 10uF 20% 6.3VC4312 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16VC4314 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16VC4315 1-125-837-91 CERAMIC CHIP 1uF 10% 6.3V
C4316 1-135-158-21 TANTALUM CHIP 15uF 20% 4VC4317 1-125-837-91 CERAMIC CHIP 1uF 10% 6.3VC4318 1-135-259-11 TANTAL. CHIP 10uF 20% 6.3VC4319 1-135-151-21 TANTALUM CHIP 4.7uF 20% 4VC4320 1-135-259-11 TANTAL. CHIP 10uF 20% 6.3V
C4321 1-164-489-11 CERAMIC CHIP 0.22uF 10% 16VC4322 1-135-259-11 TANTAL. CHIP 10uF 20% 6.3VC4323 1-131-862-91 TANTAL. CHIP 47uF 20% 4VC4324 1-131-862-91 TANTAL. CHIP 47uF 20% 4VC4325 1-125-837-91 CERAMIC CHIP 1uF 10% 6.3V
C4326 1-125-837-91 CERAMIC CHIP 1uF 10% 6.3VC4327 1-135-259-11 TANTAL. CHIP 10uF 20% 6.3VC4328 1-135-259-11 TANTAL. CHIP 10uF 20% 6.3VC4401 1-107-819-11 CERAMIC CHIP 0.022uF 10% 16VC4402 1-164-942-11 CERAMIC CHIP 0.0068uF 10% 16V
C4403 1-107-819-11 CERAMIC CHIP 0.022uF 10% 16VC4404 1-164-942-11 CERAMIC CHIP 0.0068uF 10% 16VC4405 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16VC4406 1-135-259-11 TANTAL. CHIP 10uF 20% 6.3VC4410 1-164-937-11 CERAMIC CHIP 0.001uF 10% 50V
C4411 1-135-259-11 TANTAL. CHIP 10uF 20% 6.3VC4412 1-164-874-11 CERAMIC CHIP 100PF 5% 50VC4413 1-164-874-11 CERAMIC CHIP 100PF 5% 50VC4414 1-164-937-11 CERAMIC CHIP 0.001uF 10% 50VC4416 1-164-874-11 CERAMIC CHIP 100PF 5% 50V
C4417 1-164-874-11 CERAMIC CHIP 100PF 5% 50VC4419 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10VC4420 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10VC4421 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10VC4423 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V
C4425 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16VC4426 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16VC4427 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16VC4428 1-164-942-11 CERAMIC CHIP 0.0068uF 10% 16VC4429 1-164-942-11 CERAMIC CHIP 0.0068uF 10% 16V
C4430 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16VC4432 1-104-847-11 TANTAL. CHIP 22uF 20% 4VC4433 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16VC4434 1-125-837-91 CERAMIC CHIP 1uF 10% 6.3VC4435 1-119-923-81 CERAMIC CHIP 0.047uF 10% 10V
C4437 1-119-923-81 CERAMIC CHIP 0.047uF 10% 10VC4501 1-164-941-11 CERAMIC CHIP 0.0047uF 10% 16VC4502 1-164-882-11 CERAMIC CHIP 220PF 5% 16VC4503 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10VC4504 1-119-923-81 CERAMIC CHIP 0.047uF 10% 10V
C4505 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10VC4506 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10VC4507 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16VC4508 1-164-941-11 CERAMIC CHIP 0.0047uF 10% 16VC4509 1-164-936-11 CERAMIC CHIP 680PF 10% 50V
C4510 1-164-941-11 CERAMIC CHIP 0.0047uF 10% 16VC4511 1-164-938-11 CERAMIC CHIP 0.0015uF 10% 50VC4512 1-164-939-11 CERAMIC CHIP 0.0022uF 10% 50VC4513 1-164-937-11 CERAMIC CHIP 0.001uF 10% 50VC4515 1-164-935-11 CERAMIC CHIP 470PF 10% 50V
C4516 1-164-937-11 CERAMIC CHIP 0.001uF 10% 50VC4517 1-164-937-11 CERAMIC CHIP 0.001uF 10% 50VC4518 1-164-937-11 CERAMIC CHIP 0.001uF 10% 50VC4519 1-164-937-11 CERAMIC CHIP 0.001uF 10% 50VC4520 1-164-937-11 CERAMIC CHIP 0.001uF 10% 50V
C4521 1-115-566-11 CERAMIC CHIP 4.7uF 10% 10VC4522 1-115-566-11 CERAMIC CHIP 4.7uF 10% 10VC4523 1-115-566-11 CERAMIC CHIP 4.7uF 10% 10VC4525 1-104-851-11 TANTAL. CHIP 10uF 20% 10VC4526 1-115-566-11 CERAMIC CHIP 4.7uF 10% 10V
C4527 1-115-566-11 CERAMIC CHIP 4.7uF 10% 10VC4528 1-115-566-11 CERAMIC CHIP 4.7uF 10% 10VC4529 1-164-947-11 CERAMIC CHIP 0.01uF 50VC4530 1-115-566-11 CERAMIC CHIP 4.7uF 10% 10VC4531 1-115-566-11 CERAMIC CHIP 4.7uF 10% 10V
C4532 1-115-566-11 CERAMIC CHIP 4.7uF 10% 10VC4533 1-135-259-11 TANTAL. CHIP 10uF 20% 6.3VC4534 1-164-506-11 CERAMIC CHIP 4.7uF 16VC4535 1-164-506-11 CERAMIC CHIP 4.7uF 16VC4536 1-135-259-11 TANTAL. CHIP 10uF 20% 6.3V
C4538 1-165-319-11 CERAMIC CHIP 0.1uF 50VC4539 1-135-259-11 TANTAL. CHIP 10uF 20% 6.3VC4541 1-135-259-11 TANTAL. CHIP 10uF 20% 6.3VC4543 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10VC4544 1-104-851-11 TANTAL. CHIP 10uF 20% 10V
C4546 1-113-987-11 TANTAL. CHIP 4.7uF 20% 25VC4547 1-119-750-11 TANTAL. CHIP 22uF 20% 6.3VC4548 1-119-750-11 TANTAL. CHIP 22uF 20% 6.3VC4549 1-135-259-11 TANTAL. CHIP 10uF 20% 6.3VC4550 1-119-750-11 TANTAL. CHIP 22uF 20% 6.3V
C4551 1-104-913-11 TANTAL. CHIP 10uF 20% 16VC4553 1-135-259-11 TANTAL. CHIP 10uF 20% 6.3VC4554 1-164-505-11 CERAMIC CHIP 2.2uF 16VC4555 1-164-505-11 CERAMIC CHIP 2.2uF 16VC4556 1-135-259-11 TANTAL. CHIP 10uF 20% 6.3V
C4557 1-104-847-11 TANTAL. CHIP 22uF 20% 4VC4559 1-104-847-11 TANTAL. CHIP 22uF 20% 4VC4601 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10VC4602 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10VC4603 1-107-819-11 CERAMIC CHIP 0.022uF 10% 16V
C4604 1-119-751-11 TANTAL. CHIP 22uF 20% 16VC4605 1-119-751-11 TANTAL. CHIP 22uF 20% 16VC4606 1-119-751-11 TANTAL. CHIP 22uF 20% 16VC4607 1-109-982-11 CERAMIC CHIP 1uF 10% 10V
(TRV18/TRV18E/TRV118E)C4608 1-109-982-11 CERAMIC CHIP 1uF 10% 10V
VA-117
6-16
Ref. No. Part No. Description Ref. No. Part No. Description
DCR-TRV16/TRV16E/TRV18/TRV18E/TRV116E/TRV118E
< CONNECTOR >
CN4001 1-691-384-11 CONNECTOR, FFC/FPC 20PCN4002 1-774-603-21 CONNECTOR, BOARD TO BOARD 100PCN4003 1-691-388-11 CONNECTOR, FFC/FPC 24PCN4004 1-691-376-21 CONNECTOR, FFC/FPC 12PCN4201 1-766-350-21 CONNECTOR, FFC/FPC 20P
* CN4601 1-580-789-21 PIN, CONNECTOR (SMD) 6P
< DIODE >
D4001 8-719-062-16 DIODE 01ZA8.2(TPL3)D4003 8-719-062-16 DIODE 01ZA8.2(TPL3)D4004 8-719-062-16 DIODE 01ZA8.2(TPL3)D4005 8-719-062-16 DIODE 01ZA8.2(TPL3)D4006 8-719-056-85 DIODE UDZSTE-178.2B
D4201 8-719-084-47 DIODE 1SV290(TPL3)D4502 8-719-081-19 DIODE 1SS383(T5RSONY1)D4503 8-719-081-19 DIODE 1SS383(T5RSONY1)D4601 8-719-062-16 DIODE 01ZA8.2(TPL3)D4602 8-719-081-19 DIODE 1SS383(T5RSONY1)
< FUSE >
0F4601 1-576-406-21 FUSE, MICRO (1.4A/32V) (1608)0F4602 1-576-406-21 FUSE, MICRO (1.4A/32V) (1608)0F4603 1-576-406-21 FUSE, MICRO (1.4A/32V) (1608)0F4604 1-576-406-21 FUSE, MICRO (1.4A/32V) (1608)0F4605 1-576-406-21 FUSE, MICRO (1.4A/32V) (1608)
(TRV18/TRV18E/TRV118E)
0F4606 1-576-406-21 FUSE, MICRO (1.4A/32V) (1608)
< FERRITE BEAD >
FB4101 1-469-676-22 FERRITE 0uHFB4201 1-469-676-22 FERRITE 0uHFB4202 1-500-329-21 FERRITE 0uHFB4301 1-469-676-22 FERRITE 0uH
< IC >
IC4101 6-701-555-01 IC AN2225NFHQBAIC4201 8-752-100-95 IC CXA3289AR-T4IC4202 8-752-405-57 IC CXD3501AR-T4IC4301 6-701-074-01 IC LA74207W-TBM-EIC4401 8-759-679-11 IC BH7870AKV-E2
IC4501 8-752-102-78 IC CXA3282R-T6IC4505 6-700-139-01 IC R1121N191B-TL
< COIL >
L4101 1-469-525-91 INDUCTOR 10uHL4102 1-469-525-91 INDUCTOR 10uHL4201 1-469-525-91 INDUCTOR 10uHL4202 1-469-891-21 INDUCTOR 6.8uHL4301 1-469-525-91 INDUCTOR 10uH
L4401 1-469-528-91 INDUCTOR 100uHL4501 1-416-670-11 INDUCTOR 33uHL4502 1-416-669-11 INDUCTOR 22uHL4503 1-416-669-11 INDUCTOR 22uHL4504 1-416-669-11 INDUCTOR 22uH
L4505 1-416-670-11 INDUCTOR 33uHL4506 1-416-669-11 INDUCTOR 22uHL4507 1-469-524-91 INDUCTOR 4.7uHL4508 1-469-524-91 INDUCTOR 4.7uHL4509 1-469-524-91 INDUCTOR 4.7uH
L4510 1-469-524-91 INDUCTOR 4.7uHL4511 1-412-056-11 INDUCTOR 4.7uHL4513 1-414-392-41 INDUCTOR 1uHL4514 1-412-056-11 INDUCTOR 4.7uHL4515 1-469-524-91 INDUCTOR 4.7uH
L4516 1-469-526-91 INDUCTOR 22uHL4517 1-469-524-91 INDUCTOR 4.7uHL4519 1-469-524-91 INDUCTOR 4.7uHL4520 1-414-392-41 INDUCTOR 1uHL4522 1-414-392-41 INDUCTOR 1uH
L4601 1-412-056-11 INDUCTOR 4.7uH
< LINE FILTER >
LF4601 1-411-957-11 FILTER, COMMON MODE
< TRANSISTOR >
Q4001 8-729-037-76 TRANSISTOR RN1111F(TPL3)Q4003 8-729-049-92 TRANSISTOR 2SC5585H-T2LQ4101 8-729-037-52 TRANSISTOR 2SC4738F-Y/GR(TPL3)Q4102 8-729-037-61 TRANSISTOR RN2104F(TPL3)Q4103 8-729-053-52 TRANSISTOR N1C01FE-Y/GR(TPLR3)
Q4301 8-729-921-51 TRANSISTOR 2SD1834-T100Q4303 8-729-054-51 TRANSISTOR RN2910FE(TPLR3)Q4304 8-729-042-29 TRANSISTOR RN1104F(TPL3)Q4305 8-729-054-52 TRANSISTOR RN1910FE(TPLR3)Q4306 8-729-037-63 TRANSISTOR UN9115J-(K8).SO
Q4307 8-729-054-52 TRANSISTOR RN1910FE(TPLR3)Q4501 8-729-043-60 TRANSISTOR CPH6102-TL-EQ4502 8-729-101-07 TRANSISTOR 2SB798-T1-DLDKQ4503 8-729-046-98 TRANSISTOR CPH6702-TL-EQ4504 8-729-037-53 TRANSISTOR 2SA1832F-Y/GR(TPL3)
Q4505 8-729-046-98 TRANSISTOR CPH6702-TL-EQ4506 8-729-044-33 TRANSISTOR CPH6701-TL-EQ4507 8-729-053-52 TRANSISTOR N1C01FE-Y/GR(TPLR3)Q4508 8-729-046-98 TRANSISTOR CPH6702-TL-EQ4509 8-729-044-33 TRANSISTOR CPH6701-TL-E
Q4510 8-729-046-98 TRANSISTOR CPH6702-TL-EQ4511 8-729-044-58 TRANSISTOR SI2304DS-T1Q4512 8-729-044-58 TRANSISTOR SI2304DS-T1Q4513 8-729-042-29 TRANSISTOR RN1104F(TPL3)Q4514 8-729-037-52 TRANSISTOR 2SC4738F-Y/GR(TPL3)
Q4515 8-729-037-53 TRANSISTOR 2SA1832F-Y/GR(TPL3)Q4516 8-729-053-52 TRANSISTOR N1C01FE-Y/GR(TPLR3)Q4517 8-729-037-52 TRANSISTOR 2SC4738F-Y/GR(TPL3)Q4518 8-729-053-54 TRANSISTOR N1A01FE-Y/GR(TPLR3)Q4519 8-729-037-52 TRANSISTOR 2SC4738F-Y/GR(TPL3)
Q4520 8-729-053-54 TRANSISTOR N1A01FE-Y/GR(TPLR3)Q4521 8-729-037-52 TRANSISTOR 2SC4738F-Y/GR(TPL3)Q4601 8-729-047-68 TRANSISTOR SSM3K03FE(TPL3)Q4602 8-729-056-54 TRANSISTOR TPCS8302(TE12L)Q4603 8-729-804-41 TRANSISTOR 2SB1122-ST-TD
VA-117
Note :The components identified bymark 0 or dotted line with mark0 are critical for safety.Replace only with part numberspecified.
Note :Les composants identifiés parune marque 0 sont critiquespour la sécurité.Ne les remplacer que par unepièce portant le numéro spécifié.
6-17
Ref. No. Part No. Description Ref. No. Part No. Description
DCR-TRV16/TRV16E/TRV18/TRV18E/TRV116E/TRV118E
Q4604 8-729-042-29 TRANSISTOR RN1104F(TPL3)Q4605 8-729-042-29 TRANSISTOR RN1104F(TPL3)Q4606 8-729-037-61 TRANSISTOR RN2104F(TPL3)
(TRV18/TRV18E/TRV118E)Q4607 8-729-037-61 TRANSISTOR RN2104F(TPL3)Q4608 8-729-023-89 TRANSISTOR 2SJ305(TE85L)
(TRV18/TRV18E/TRV118E)
Q4609 8-729-023-89 TRANSISTOR 2SJ305(TE85L)Q4610 8-729-056-54 TRANSISTOR TPCS8302(TE12L)
(TRV18/TRV18E/TRV118E)Q4611 8-729-056-19 TRANSISTOR TPC6101(TE85R)
(TRV16/TRV16E/TRV116E)
< RESISTOR >
R4001 1-218-990-11 SHORT CHIP 0 (TRV18/TRV18E/TRV118E)R4002 1-218-990-11 SHORT CHIP 0R4003 1-218-990-11 SHORT CHIP 0 (TRV18/TRV18E/TRV118E)R4004 1-218-990-11 SHORT CHIP 0 (TRV18/TRV18E/TRV118E)R4005 1-218-990-11 SHORT CHIP 0 (TRV18/TRV18E/TRV118E)
R4009 1-218-939-11 RES-CHIP 68 5% 1/16WR4010 1-218-959-11 RES-CHIP 3.3K 5% 1/16WR4011 1-216-017-91 RES-CHIP 47 5% 1/10WR4012 1-216-017-91 RES-CHIP 47 5% 1/10WR4013 1-218-990-11 SHORT CHIP 0
R4101 1-218-961-11 RES-CHIP 4.7K 5% 1/16WR4102 1-218-961-11 RES-CHIP 4.7K 5% 1/16WR4103 1-218-941-81 RES-CHIP 100 5% 1/16WR4104 1-218-981-11 RES-CHIP 220K 5% 1/16WR4105 1-218-953-11 RES-CHIP 1K 5% 1/16W
R4106 1-218-953-11 RES-CHIP 1K 5% 1/16WR4107 1-208-715-11 METAL CHIP 22K 0.5% 1/16WR4108 1-218-953-11 RES-CHIP 1K 5% 1/16WR4109 1-218-953-11 RES-CHIP 1K 5% 1/16WR4110 1-218-965-11 RES-CHIP 10K 5% 1/16W
R4111 1-218-957-11 RES-CHIP 2.2K 5% 1/16WR4112 1-218-935-11 RES-CHIP 33 5% 1/16WR4113 1-218-935-11 RES-CHIP 33 5% 1/16WR4114 1-218-935-11 RES-CHIP 33 5% 1/16WR4115 1-218-935-11 RES-CHIP 33 5% 1/16W
R4116 1-218-935-11 RES-CHIP 33 5% 1/16WR4117 1-218-935-11 RES-CHIP 33 5% 1/16WR4118 1-218-953-11 RES-CHIP 1K 5% 1/16WR4119 1-218-953-11 RES-CHIP 1K 5% 1/16WR4120 1-218-953-11 RES-CHIP 1K 5% 1/16W
R4121 1-218-953-11 RES-CHIP 1K 5% 1/16WR4201 1-218-985-11 RES-CHIP 470K 5% 1/16WR4202 1-208-935-11 METAL CHIP 100K 0.5% 1/16WR4203 1-218-990-11 SHORT CHIP 0R4205 1-218-958-11 RES-CHIP 2.7K 5% 1/16W
R4206 1-218-973-11 RES-CHIP 47K 5% 1/16WR4207 1-218-975-11 RES-CHIP 68K 5% 1/16WR4208 1-218-969-11 RES-CHIP 22K 5% 1/16WR4209 1-218-975-11 RES-CHIP 68K 5% 1/16WR4210 1-218-989-11 RES-CHIP 1M 5% 1/16W
R4211 1-218-977-11 RES-CHIP 100K 5% 1/16WR4212 1-218-941-81 RES-CHIP 100 5% 1/16WR4213 1-218-941-81 RES-CHIP 100 5% 1/16WR4214 1-218-941-81 RES-CHIP 100 5% 1/16WR4216 1-208-927-11 METAL CHIP 47K 0.5% 1/16W
R4217 1-218-989-11 METAL CHIP 1M 0.5% 1/16WR4221 1-218-990-11 SHORT CHIP 0R4222 1-218-990-11 SHORT CHIP 0R4223 1-218-990-11 SHORT CHIP 0R4224 1-218-953-11 RES-CHIP 1K 5% 1/16W
R4301 1-218-971-11 RES-CHIP 33K 5% 1/16WR4302 1-218-981-11 RES-CHIP 220K 5% 1/16WR4303 1-218-960-11 RES-CHIP 3.9K 5% 1/16WR4304 1-218-965-11 RES-CHIP 10K 5% 1/16WR4305 1-218-965-11 RES-CHIP 10K 5% 1/16W
R4306 1-218-957-11 RES-CHIP 2.2K 5% 1/16WR4307 1-218-957-11 RES-CHIP 2.2K 5% 1/16WR4308 1-218-973-11 RES-CHIP 47K 5% 1/16WR4309 1-218-973-11 RES-CHIP 47K 5% 1/16WR4310 1-218-953-11 RES-CHIP 1K 5% 1/16W
R4311 1-218-953-11 RES-CHIP 1K 5% 1/16WR4316 1-218-937-11 RES-CHIP 47 5% 1/16WR4317 1-218-937-11 RES-CHIP 47 5% 1/16WR4318 1-218-937-11 RES-CHIP 47 5% 1/16WR4319 1-218-937-11 RES-CHIP 47 5% 1/16W
R4401 1-218-957-11 RES-CHIP 2.2K 5% 1/16WR4402 1-218-958-11 RES-CHIP 2.7K 5% 1/16WR4403 1-218-965-11 RES-CHIP 10K 5% 1/16WR4404 1-218-961-11 RES-CHIP 4.7K 5% 1/16WR4405 1-218-990-11 SHORT CHIP 0
R4406 1-218-957-11 RES-CHIP 2.2K 5% 1/16WR4407 1-218-957-11 RES-CHIP 2.2K 5% 1/16WR4408 1-218-963-11 RES-CHIP 6.8K 5% 1/16WR4409 1-218-963-11 RES-CHIP 6.8K 5% 1/16WR4410 1-218-953-11 RES-CHIP 1K 5% 1/16W
R4411 1-218-953-11 RES-CHIP 1K 5% 1/16WR4415 1-218-969-11 RES-CHIP 22K 5% 1/16WR4417 1-218-969-11 RES-CHIP 22K 5% 1/16WR4418 1-218-973-11 RES-CHIP 47K 5% 1/16WR4419 1-218-973-11 RES-CHIP 47K 5% 1/16W
R4420 1-218-966-11 RES-CHIP 12K 5% 1/16WR4421 1-218-966-11 RES-CHIP 12K 5% 1/16WR4422 1-218-990-11 SHORT CHIP 0R4423 1-218-965-11 RES-CHIP 10K 5% 1/16WR4424 1-218-966-11 RES-CHIP 12K 5% 1/16W
R4425 1-218-977-11 RES-CHIP 100K 5% 1/16WR4427 1-218-959-11 RES-CHIP 3.3K 5% 1/16WR4430 1-218-990-11 SHORT CHIP 0R4501 1-208-715-11 METAL CHIP 22K 0.5% 1/16WR4502 1-218-971-11 RES-CHIP 33K 5% 1/16W
R4503 1-218-963-11 RES-CHIP 6.8K 5% 1/16WR4504 1-218-985-11 METAL CHIP 470K 0.5% 1/16WR4505 1-218-990-11 SHORT CHIP 0R4506 1-218-967-11 RES-CHIP 15K 5% 1/16WR4507 1-218-965-11 RES-CHIP 10K 5% 1/16W
R4508 1-208-935-11 METAL CHIP 100K 0.5% 1/16WR4509 1-216-864-11 METAL CHIP 0 5% 1/16WR4510 1-218-990-11 SHORT CHIP 0R4511 1-218-969-11 RES-CHIP 22K 5% 1/16WR4512 1-218-961-11 RES-CHIP 4.7K 5% 1/16W
R4513 1-218-990-11 SHORT CHIP 0R4514 1-218-961-11 RES-CHIP 4.7K 5% 1/16WR4515 1-208-713-11 METAL CHIP 18K 0.5% 1/16WR4517 1-218-990-11 SHORT CHIP 0R4518 1-218-971-11 RES-CHIP 33K 5% 1/16W
VA-117
6-18
Ref. No. Part No. Description Ref. No. Part No. Description
DCR-TRV16/TRV16E/TRV18/TRV18E/TRV116E/TRV118E
R4519 1-218-969-11 RES-CHIP 22K 5% 1/16WR4520 1-218-965-11 RES-CHIP 10K 5% 1/16WR4521 1-218-990-11 SHORT CHIP 0R4524 1-218-973-11 RES-CHIP 47K 5% 1/16WR4525 1-218-961-11 RES-CHIP 4.7K 5% 1/16W
R4526 1-218-970-11 METAL CHIP 27K 0.5% 1/16WR4527 1-208-720-11 METAL CHIP 36K 0.5% 1/16WR4528 1-218-973-11 RES-CHIP 47K 5% 1/16WR4529 1-218-969-11 RES-CHIP 22K 5% 1/16WR4531 1-218-973-11 RES-CHIP 47K 5% 1/16W
R4532 1-218-977-11 RES-CHIP 100K 5% 1/16WR4533 1-218-969-11 RES-CHIP 22K 5% 1/16WR4534 1-208-935-11 METAL CHIP 100K 0.5% 1/16WR4535 1-208-927-11 METAL CHIP 47K 0.5% 1/16WR4536 1-208-711-11 METAL CHIP 15K 0.5% 1/16W
R4537 1-218-977-11 RES-CHIP 100K 5% 1/16WR4538 1-218-969-11 RES-CHIP 22K 5% 1/16WR4539 1-208-935-11 METAL CHIP 100K 0.5% 1/16WR4540 1-218-967-11 RES-CHIP 15K 5% 1/16WR4541 1-208-943-11 METAL CHIP 220K 0.5% 1/16W
R4542 1-218-977-11 RES-CHIP 100K 5% 1/16WR4543 1-218-977-11 RES-CHIP 100K 5% 1/16WR4544 1-218-961-11 RES-CHIP 4.7K 5% 1/16WR4545 1-208-943-11 METAL CHIP 220K 0.5% 1/16WR4546 1-208-931-11 METAL CHIP 68K 0.5% 1/16W
R4550 1-208-699-11 METAL CHIP 4.7K 0.5% 1/16WR4551 1-208-927-11 METAL CHIP 47K 0.5% 1/16WR4552 1-208-711-11 METAL CHIP 15K 0.5% 1/16WR4554 1-218-990-11 SHORT CHIP 0R4601 1-218-953-11 RES-CHIP 1K 5% 1/16W
R4604 1-218-977-11 RES-CHIP 100K 5% 1/16WR4605 1-218-989-11 RES-CHIP 1M 5% 1/16WR4607 1-216-797-11 METAL CHIP 10 5% 1/16WR4608 1-218-953-11 RES-CHIP 1K 5% 1/16WR4609 1-218-963-11 RES-CHIP 6.8K 5% 1/16W
R4610 1-218-973-11 RES-CHIP 47K 5% 1/16W(TRV18/TRV18E/TRV118E)
R4611 1-218-973-11 RES-CHIP 47K 5% 1/16WR4612 1-218-941-81 RES-CHIP 100 5% 1/16W
(TRV18/TRV18E/TRV118E)R4613 1-218-989-11 RES-CHIP 1M 5% 1/16W
(TRV18/TRV18E/TRV118E)R4614 1-218-941-81 RES-CHIP 100 5% 1/16W
R4615 1-218-989-11 RES-CHIP 1M 5% 1/16WR4617 1-218-953-11 RES-CHIP 1K 5% 1/16W
(TRV18/TRV18E/TRV118E)R4618 1-218-953-11 RES-CHIP 1K 5% 1/16W
(TRV18/TRV18E/TRV118E)
< TRANSFORMER >
0T4501 1-435-252-21 TRANSFORMER, DC-DC CONVERTER************************************************************
A-7078-154-A VC-280 (F) BOARD, COMPLETE (SERVICE)(TRV18/TRV18E:E,HK,AUS,CH,JE/TRV118E)
**************************************A-7078-277-A VC-280 (O) BOARD, COMPLETE (SERVICE)
(TRV16E:AEP,UK,EE,NE)**************************************
A-7078-278-A VC-280 BOARD, COMPLETE (SERVICE)(TRV16/TRV16E:E,HK,AUS,CH/TRV116E)
**************************************A-7078-279-A VC-280 (FO) BOARD, COMPLETE (SERVICE)
(TRV18E:AEP,UK,EE,NE)**************************************
************************************************************
Note :The components identified bymark 0 or dotted line with mark0 are critical for safety.Replace only with part numberspecified.
Note :Les composants identifiés parune marque 0 sont critiquespour la sécurité.Ne les remplacer que par unepièce portant le numéro spécifié.
VA-117 VC-280
Electrical parts list of the VC-280 boardare not shown.Pages from 6-19 to 6-24 are not shown.
6-25E
DCR-TRV16/TRV16E/TRV18/TRV18E/TRV116E/TRV118E
Ref. No. Part No. Description Ref. No. Part No. Description
ACCESSORIES***********
1-475-141-61 REMOTE COMMANDER (RMT-814)0 1-475-599-11 ADAPTOR, AC (AC-L10)
(TRV16:E,HK/TRV16E:AEP,UK,EE,NE,E,HK,AUS/TRV116E/TRV18:US,CND,E,HK,JE/
TRV18E:AEP,UK,EE,NE,E,HK,AUS,JE/TRV118E)0 1-475-599-71 ADAPTOR, AC (AC-L10) (TRV16:KR/TRV18:KR)0 1-475-599-81 ADAPTOR, AC (AC-L10)
(TRV16E:CH/TRV18E:CH)1-569-007-11 ADAPTOR, CONVERSION 2P
(TRV18:JE/TRV18E:JE)
1-569-008-21 ADAPTOR, CONVERSION 2P(TRV16:E,HK/TRV16E:E, HK/TRV18:E,HK/TRV18E:HK)
1-573-291-11 CONNECTOR, CONVERSION 21P(TRV16E:AEP,UK,EE,NE/TRV116E/TRV18E:AEP,UK,EE,NE/TRV118E)
0 1-696-819-11 CORD, POWER (TRV16E:AUS/TRV18E:AUS)1-757-293-21 CORD, CONNECTION (USB 5P)
0 1-769-608-11 CORD, POWER(TRV16:E/TRV16E:AEP,EE,NE,E/TRV116E:AEP,EE,NE/TRV18:E/TRV18E:AEP,EE,NE,E/TRV118E:AEP,EE,NE)
0 1-776-985-11 CORD, POWER (TRV16:KR/TRV18:KR)0 1-782-476-11 CORD, POWER (TRV16E:CH/TRV18E:CH)0 1-783-374-11 CORD, POWER
(TRV16:HK/TRV16E:UK,HK/TRV116E:UK/TRV18:HKTRV18E:UK,HKTRV118E:UK)
0 1-790-107-22 CORD, POWER (TRV18:US,CND)0 1-790-732-11 CORD, POWER (TRV18:JE/TRV18E:JE)
1-824-097-11 CORD, CONNECTION (AV CABLE) (1.5m)3-072-414-01 SPVD-008 (CD-ROM USE DRIVER)
(TRV16/TRV16E/TRV116E/TRV18:E,HK,JE,KR/TRV18E/TRV118E)
3-072-654-01 SPVD-008 (I) (CD-ROM USE DRIVER)(TRV18:US,CND)
3-073-855-11 MANUAL, INSTRUCTION (ENGLISH)(TRV16:E,HK/TRV18:US,CND,E,HK,JE)
3-073-855-21 MANUAL, INSTRUCTION (FRENCH)(TRV18:CND)
3-073-855-31 MANUAL, INSTRUCTION(SPANISH/PORTUGUESE) (TRV16:E/TRV18:E,JE)
3-073-855-41 MANUAL, INSTRUCTION(TRADITIONAL CHINESE) (TRV16:E,HK/TRV18:E,HK)
3-073-855-51 MANUAL, INSTRUCTION (KOREAN)(TRV16:KR/TRV18:JE,KR)
3-073-855-61 MANUAL, INSTRUCTION (ARABIC)(TRV16:E/TRV18:E)
3-075-067-11 MANUAL, INSTRUCTION (ENGLISH/RUSSIAN)(TRV16E:UK/TRV116E:UK/TRV18E:UK/TRV118E:UK)
3-075-067-21 MANUAL, INSTRUCTION (FRENCH/GERMAN)(TRV16E:AEP/TRV116E:AEP/TRV18E:AEP/TRV118E:AEP)
3-075-067-31 MANUAL, INSTRUCTION (ENGLISH/DUTCH)(TRV16E:AEP/TRV116E:AEP/TRV18E:AEP/TRV118E:AEP)
3-075-067-41 MANUAL, INSTRUCTION(SPANISH/PORTUGUESE) (TRV16E:AEP/
TRV116E:AEP/TRV18E:AEP/TRV118E:AEP)3-075-067-51 MANUAL, INSTRUCTION (ITALIAN/GREEK)
(TRV16E:AEP/TRV116E:AEP/TRV18E:AEP/TRV118E:AEP)3-075-067-61 MANUAL, INSTRUCTION (ENGLISH/SWEDISH)
(TRV16E:NE/TRV116E:NE/TRV18E:NE/TRV118E:NE)
3-075-067-71 MANUAL, INSTRUCTION (DANISH/FINNISH)(TRV16E:NE/TRV116E:NE/TRV18E:NE/TRV118E:NE)
3-075-068-11 MANUAL, INSTRUCTION (ENGLISH/RUSSIAN)(TRV16E:E,HK,AUS,CH/TRV18E:E,HK,AUS,CH,JE)
3-075-068-21 MANUAL, INSTRUCTION (FRENCH/GERMAN)(TRV16E:E/TRV18E:E,JE)
3-075-068-31 MANUAL, INSTRUCTION (ARABIC/PERSIAN)(TRV16E:E/TRV18E:E)
3-075-068-41 MANUAL, INSTRUCTION(TRADITIONAL CHINESE) (TRV16E:HK/TRV18E:HK)
3-075-068-51 MANUAL, INSTRUCTION(SIMPLIFIED CHINESE) (TRV16E:E,CH/TRV18E:E,CH,JE)
3-742-854-01 LID, BATTERY CASE (FOR RMT-814)3-987-015-01 BELT (S), SHOULDERA-7024-735-A MEMORY STICK (MSA-8A)
(TRV18/TRV18E/TRV118E)X-3950-537-1 CAP ASSY, LENS
NP-FM30 BATTERY PACK (NOT SUPPLIED)NP-FM50 BATTERY PACK (NOT SUPPLIED)
Note :The components identified bymark 0 or dotted line with mark0 are critical for safety.Replace only with part numberspecified.
Note :Les composants identifiés parune marque 0 sont critiquespour la sécurité.Ne les remplacer que par unepièce portant le numéro spécifié.
Take a copy of OPTICAL AXISFRAME with a clear sheet for use.
— 188 —
⟨OPTICAL AXIS FRAME⟩
DCR-TRV16/TRV16E/TRV18/TRV18E/TRV116E/TRV118E
Take a copy of CAMERA COLORREPRODUCTION FRAME witha clear sheet for use.
— 189 —
⟨FOR CAMERA COLOR REPRODUCTION ADJUSTMENT⟩
DCR-TRV16/TRV18
For NTSC model
For PAL model
DCR-TRV16E/TRV18E/TRV116E/TRV118E
DCR-TRV16/TRV16E/TRV18/TRV18E/TRV116E/TRV118E
DCR-TRV16/TRV16E/TRV18/TRV18E/TRV116E/TRV118E
— 190 —Sony EMCS Co. 2004I1600-1
©2004.9Published by DI Technical Support Section
9-929-952-31
Revision History
Ver.
1.0
1.1
1.2
1.3
Date
2002.03
2002.06
2003.11
2004.09
History
Official Release
Correction-1
Correction-2
Correction-3
Contents
—
Correction of AdjustmentsS.M. correction: Page 5-9
Correction of the SELF-DIAGNOSIS CODETABLE.S.M. correction: Page 1-3
Correction of part numberS.M. correction: Page 6-1
S.M. Rev.issued
—
Yes
Yes
Yes
992995234.pdfReverse