Post on 03-May-2023
HCD-CPX22/NXM3US Model
HCD-CPX22
AEP ModelHCD-CPX22/NXM3
UK ModelE Model
HCD-CPX22
SERVICE MANUAL
HCD-CPX22
MICRO Hi-Fi COMPONENT SYSTEMHCD-NXM3
MiNi Hi-Fi COMPONENT SYSTEMSony CorporationHome Audio CompanyPublished by Sony Engineering Corporation
9-877-828-012004D02-1© 2004.04
SPECIFICATIONS
Ver 1.0 2004. 04
– Continued on next page –
• HCD-CPX22 is the Amplifier, CD player,tape deck and tuner section in CMT-CPX22.
• HCD-NXM3 is the Amplifier, CD player,tape deck and tuner section in MHC-NXM3.
Model Name Using Similar Mechanism NEW
CD CD Mechanism Type CDM81B-F1BD81A
Section Base Unit Name BU-F1BD81A
Optical Pick-up Name KSM-215DCP/C2NP
TAPEModel Name Using Similar Mechanism NEWSection
Amplifier sectionFor the U.S.A. modelAUDIO POWER SPECIFICATIONSHCD-CPX22POWER OUTPUT AND TOTAL HARMONIC DISTORTION:With 4-ohm loads, both channels driven, from 120 – 10,000 Hz;rated 100 watts per channel minimum RMS power, with no morethan 10% total harmonic distortion from 250 milliwatts to ratedoutput.
Other models:The following measured at AC 120 – 127/220 – 240 V, 50/60 Hz(Saudi Arabian model only)The following measured at AC 230 V, 50/60 Hz (European andRussian models only)The following measured at AC 120/220 – 240 V, 50/60 Hz (exceptfor European, Russian and Saudi Arabian models)
DIN power output (rated): 75 + 75 watts (4 ohms at 1 kHz, DIN)Continuous RMS power output (reference):
100 + 100 watts(4 ohms at 1 kHz, 10% THD)
InputsVIDEO/MD IN (phono jacks): Sensitivity 250/450 mV, impedance
47 kilohmsOutputsDIGITAL (OPTICAL) OUT: Optical Wavelength: 660 nmPHONES (mini jack): accepts headphones with an
impedance of 8 ohms or more
Photo : HCD-CPX22
SPEAKER: Use only the supplied speakersSS-CPX22(HCD-CPX22)SS-NXM3(HCD-NXM3)
CD player sectionSystem Compact disc and digital audio systemLaser Semiconductor laser
(λ=770 – 810 nm)Emission duration: continuous
Frequency response 2 Hz – 20 kHz (±0.5 dB)
Tape deck sectionRecording system 4-track 2-channel stereoFrequency response 50 – 13,000 Hz (±3 dB), using Sony
TYPE I cassettes
2
HCD-CPX22/NXM3
Tuner sectionFM stereo, FM/AM superheterodyne tunerFM tuner sectionTuning rangeU.S.A. model: 87.5 – 108.0 MHz (100-kHz step)Russian model: 65.0 – 74.0 MHz (10-kHz step)
(There is no stereo effect)87.5 – 108.0 MHz (50-kHz step)
Other models: 87.5 – 108.0 MHz (50-kHz step)Antenna FM lead antennaAntenna terminals 75 ohms unbalancedIntermediate frequency 10.7 MHzAM tuner sectionTuning rangePan-American model: 530 – 1,710 kHz
(with the tuning interval set at 10 kHz)531 – 1,710 kHz(with the tuning interval set at 9 kHz)
European, Russian and Saudi Arabian models:531 – 1,602 kHz(with the tuning interval set at 9 kHz)
Other models: 531 – 1,602 kHz(with the tuning interval set at 9 kHz)530 – 1,710 kHz(with the tuning interval set at 10 kHz)
Antenna AM loop antennaAntenna terminals External antenna terminalIntermediate frequency 450 kHz
GeneralPower requirementsU.S.A. model: 120 V AC, 60 HzEuropean and Russian models:
230 V AC, 50/60 HzSaudi Arabian model: 120 – 127 V or 220 – 240 V AC,
50/60 HzAdjustable with voltage selector
Other models: 120 V, 220 – 240 V AC, 50/60 HzAdjustable with voltage selector
Power consumptionU.S.A. model: 65 wattsEuropean and Russian models: 65 watts
0.3 watts (in Power Saving mode)Other models: 65 wattsDimensions (w/h/d) incl. projecting parts and controlsAmplifier/Tuner/Tape/CD section:
Approx. 230 x 292 x 355 mmMassAmplifier/Tuner/Tape/CD section:
Approx. 6.1 kgSupplied accessories Remote Commander (1)
Size AA (R6) batteries (2)AM loop antenna (1)FM lead antenna (1)Speaker pads (8)Speaker cords
Design and specifications are subject to change without notice.
After correcting the original service problem, perform the followingsafety checks before releasing the set to the customer:Check the antenna terminals, metal trim, “metallized” knobs, screws,and all other exposed metal parts for AC leakage. Check leakage asdescribed below.
LEAKAGEThe AC leakage from any exposed metal part to earth ground andfrom all exposed metal parts to any exposed metal part having areturn to chassis, must not exceed 0.5 mA (500 microamperes).Leakage current can be measured by any one of three methods.
1. A commercial leakage tester, such as the Simpson 229 or RCAWT-540A. Follow the manufacturers’ instructions to use theseinstruments.
2. A battery-operated AC milliammeter. The Data Precision 245digital multimeter is suitable for this job.
3. Measuring the voltage drop across a resistor by means of aVOM or battery-operated AC voltmeter. The “limit” indicationis 0.75 V, so analog meters must have an accurate low-voltagescale. The Simpson 250 and Sanwa SH-63Trd are examplesof a passive VOM that is suitable. Nearly all battery operateddigital multimeters that have a 2V AC range are suitable. (SeeFig. A)
SAFETY CHECK-OUT
To Exposed Metal Parts on Set
0.15 µF 1.5 k ΩACVoltmeter(0.75 V)
Earth Ground
Fig. A. Using an AC voltmeter to check AC leakage.
3
HCD-CPX22/NXM3
TABLE OF CONTENTS
1. SERVICING NOTES ................................................ 4
2. GENERALLocation of Controls ........................................................ 5
3. DISASSEMBLY3-1. Disassembly Flow ........................................................... 73-2. Case ................................................................................. 83-3. Main Board, Front Panel Section .................................... 83-4. Tape Mechanism Deck .................................................... 93-5. Panel Board ..................................................................... 93-6. Back Panel ....................................................................... 103-7. CD Mechanism Deck (CDM81B-F1BD81A) ................. 103-8. S-Master Board ................................................................ 113-9. Tray .................................................................................. 113-10. M761 (LD/ST Motor), M762 (BU U/D Motor) .............. 123-11. Base Unit (BU-F1BD81A) .............................................. 123-12. BD Board ......................................................................... 13
4. TEST MODE .............................................................. 14
5. MECHANICAL ADJUSTMENTS ....................... 17
6. ELECTRICAL ADJUSTMENTSDeck section .................................................................... 17CD Section ...................................................................... 18
7. DIAGRAMS7-1. Circuit Board Location .................................................... 217-2. Block Diagram – CD Servo Section – ............................ 227-3. Block Diagram – Tuner/Tape Deck Section – ................ 23
7-4. Block Diagram – Main Section – ................................... 247-5. Block Diagram – S-Master Section – ............................. 257-6. Printed Wiring Board – BD Board – .............................. 267-7. Schematic Diagram – BD Board – ................................. 277-8. Printed Wiring Board – CD Mechanism Board – ........... 287-9. Schematic Diagram – CD Mechanism Board – ............. 297-10. Printed Wiring Boards – Main Board – .......................... 307-11. Schematic Diagram – Main Board (1/3) – ..................... 317-12. Schematic Diagram – Main Board (2/3) – ..................... 327-13. Schematic Diagram – Main Board (3/3) – ..................... 337-14. Printed Wiring Boards – Panel Board – ......................... 347-15. Schematic Diagram – Panel Board – ............................... 357-16. Printed Wiring Board – Disc SW, Vol, HP Board – ....... 367-17. Schematic Diagram – Disc SW, Vol, HP Board – .......... 377-18. Printed Wiring Board – S-Master Board – ..................... 387-19. Schematic Diagram – S-Master Board – ........................ 397-20. IC Block Diagram ........................................................... 407-21. IC Pin Function Description ............................................ 41
8. EXPLODED VIEWS8-1. Main Section .................................................................... 478-2. Front Panel Section ......................................................... 488-3. Chassis Section ................................................................ 498-4. CD Mechanism Deck Section-1
(CDM81B-F1BD81A) .................................................... 508-5. CD Mechanism Deck Section-2
(CDM81B-F1BD81A) .................................................... 518-6. CD Mechanism Deck Section-3
(CDM81B-F1BD81A) .................................................... 52
9. ELECTRICAL PARTS LIST ................................ 53
Notes on chip component replacement• Never reuse a disconnected chip component.• Notice that the minus side of a tantalum capacitor may be
damaged by heat.
Flexible Circuit Board Repairing• Keep the temperature of soldering iron around 270˚C
during repairing.• Do not touch the soldering iron on the same conductor of the
circuit board (within 3 times).• Be careful not to apply force on the conductor when soldering
or unsoldering.
CAUTIONUse of controls or adjustments or performance of proceduresother than those specified herein may result in hazardousradiation exposure.
This appliance is classified asa CLASS 1 LASER product.This label is located on the rearexterior.
SAFETY-RELATED COMPONENT WARNING!!
COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE WITHMARK 0 ON THE SCHEMATIC DIAGRAMS AND IN THE PARTSLIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESECOMPONENTS WITH SONY PARTS WHOSE PART NUMBERSAPPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTSPUBLISHED BY SONY.
4
HCD-CPX22/NXM3SECTION 1
SERVICING NOTES
NOTES ON HANDLING THE OPTICAL PICK-UP BLOCKOR BASE UNIT
The laser diode in the optical pick-up block may suffer electrostaticbreak-down because of the potential difference generated by thecharged electrostatic load, etc. on clothing and the human body.During repair, pay attention to electrostatic break-down and alsouse the procedure in the printed matter which is included in therepair parts.The flexible board is easily damaged and should be handled withcare.
NOTES ON LASER DIODE EMISSION CHECK
The laser beam on this model is concentrated so as to be focused onthe disc reflective surface by the objective lens in the optical pick-up block. Therefore, when checking the laser diode emission, observefrom more than 30 cm away from the objective lens.
LASER DIODE AND FOCUS SEARCH OPERATION CHECK
Carry out the “S curve check” in “CD section adjustment” and checkthat the S curve waveform is output several times.
• MODEL IDENTIFICATION– Back Panel –
MODEL PART No.
AEP, UK models 4-253-358-0[]
RU model 4-253-358-1[]
E3 model 4-253-358-2[]
E51 model 4-253-358-3[]
US model 4-253-358-4[]
EA model 4-253-358-5[]
• AbbreviationE3 : 240 V AC Area in E modelE51 : Chilean and Peruvian modelEA : Saudi Arabia modelRU : Russian model
PART No.
• SERVICE POSITION FOR TAPE MECHANISM DECK
Jig (J-2501-271-A)
Jig (J-2501-270-A)
tape mechanism deck
CN302
CN301
5
HCD-CPX22/NXM3SECTION 2GENERAL This section is extracted
from instruction manual.
LOCATING THE CONTROLS
Main unit
ALBUM +/– qaBASS control w;CD wkCD SYNC wsDeck A qjDeck B qgDIMMER wdDISC 1 – 5 3Disc tray 9DISPLAY wfDisplay window 4DSGX qs
PHONES jack qhRemote sensor 2TAPE A/B wh TREBLE control qlTUNER/BAND wjTUNING +/– 0VIDEO/MD wgVOLUME control qd
?/1 (power) 1nN (play) 5X (pause) 6x (stop) 7CD Z (eject) 8.m/M> (rewind/fast
forward, go back/go forward) 0
TAPE Z B(eject) qfA TAPE Z (eject) qkz START wa
List of button locations and reference pages
ALPHABETICAL ORDER
A – O P – Z
BUTTON DESCRIPTIONS
1 2 3 4
56789
0
qa
qs
qd
qf
wjwk
whwg
wfwdwswaw;ql
qk
qj
qh
qg
6
HCD-CPX22/NXM3This section is extractedfrom instruction manual.
Remote control
ALBUM – qdALBUM + qaCD qkCLEAR qgCLOCK/TIMER SELECT 2 CLOCK/TIMER SET 3
DISC SKIP 0DISPLAY waENTER 9EQ qf
FM MODE 4FUNCTION 6PLAY MODE w;REPEAT 4SLEEP wsTAPE qjTUNER BAND 5TUNER MEMORY qlTUNING MODE w;VOLUME +/– qs
?/1 (power) 1m/M (rewind/fast forward) 7
N (play) 8X (pause) 8x (stop) 8./> (go back/go forward) qh–/+ (tuning) qh
ALPHABETICAL ORDER
A – E F – Z
BUTTON DESCRIPTIONS
456
7
8
9
q;
ws 1
qd
qg
qf
waw;qlqkqj
qh
qa
qs
32
7
HCD-CPX22/NXM3SECTION 3
DISASSEMBLY
• This set can be disassembled in the order shown below.
3-1. DISASSEMBLY FLOW
3-2.CASE(Page 8)
3-3.MAIN BOARD, FRONT PANEL SECTION(Page 8)
3-12.BD BOARD (Page 13)
3-4.TAPE MECHANISM DECK(Page 9)
3-10.M761 (LD/ST MOTOR), M762 (BU U/D MOTOR) (Page 12)
3-9.TRAY (Page 11)
3-8.S-MASTER BOARD (Page 11)
3-5.PANEL BOARD(Page 9)
3-11.BASE UNIT (BU-F1BD81A) (Page 12)
3-6.BACK PANEL (Page 10)
3-7.CD MECHANISM DECK (CDM81B-F1BD81A) (Page 10)
SET
8
HCD-CPX22/NXM3
Note: Follow the disassembly procedure in the numerical order given.
3-2. CASE
3-3. MAIN BOARD, FRONT PANEL SECTION
1 three screws (CASE 3 TP2)
2 three screws (CASE 3 TP2)
3 two screws (+BVTP 3X8)
4 two screws (+BVTP 3X8)
5 screw (+BVTP 3X8)
6
7 CASE
1 two screws (+BVTP 3X8)
3MAIN board
4 connector (CN301)
5 connector (CN302)
6 connector (CN107)
7 CN303
8 connector (CN304)
9 connector (CN105)
qa CN106
0 connector (CN101)
qd connector (CN401)qs CN112
qf CN204
qg CN372qh CN371
qj CN109
qk CN110
2 two screws (+BVTP 2.6X8)
ql two screws (+BVTP 3X8)
w; front panel section
9
HCD-CPX22/NXM3
3-4. TAPE MECHANISM DECK
3-5. PANEL BOARD
3 two screws (+BV (B3))
4 two screws (+BV (B3))
5 tape mechanism deck
2
1
1 four screws (+BVTP 2.6X8)
2 screw (+BVTP 2.6X8)
3 screw (+BVTP 2.6X8)
4 bracket (main)
5 screw (+BVTP 2.6X8)
6 three screws (+BVTP 2.6X8)
7 PANEL board
10
HCD-CPX22/NXM3
3-6. BACK PANEL
3-7. CD MECHANISM DECK (CDM81B-F1BD81A)
1 screw (+BVTP 3X8)
2 two screws (+BVTP 3X8)
3 two screws (+BVTP 2.6X8)
4 back panel section
1 screw (+BVTP 3X8)
2 two screws (+BVTP 3X8)
4 two screws (+BVTP 3X8)
5 screw (+BVTP 3X8)
6 screw (+BVTP 3X8)
7 screw (+BVTP 3X8)
3 bracket
8 CD mechanism deck (CDM81B-F1BD81A)
9 CN701
0 CN201
11
HCD-CPX22/NXM3
3-8. S-MASTER BOARD
3-9. TRAY
1 two screws (+BTP 2.6X8)
2 two screws (+BTP 2.6X8)
3 bracket
5 tray
4
1 connector (CN701)
3 connector (CN702)
2 two screws (+BVTP 3X8)
4 two screws (+BVTP 3X8)
5 S-MASTER board
12
HCD-CPX22/NXM3
3-10. M761 (LD/ST MOTOR), M762 (BU U/D MOTOR)
3-11. BASE UNIT (BU-F1BD81A)
1 two screws (+BTP 2.6X8)
2 MOTOR board
3 Remove soldering from the two points.5 Remove soldering from the two points.
6 M762 (BU U/D MOTOR)
4 M761 (LD/ST MOTOR)
1 two floating screws (+PTPWH2.6)
2 base unit (BU-F1BD81A)
13
HCD-CPX22/NXM3
3-12. BD BOARD
1 floating screw (+PTPWH2.6)
2 coil spring (insulator)
3 insulator
4 floating screw (+PTPWH2.6)
5 coil spring (insulator)
6 insulator
7 floating screw (+PTPWH2.6)
8 coil spring (insulator)
9 insulator
0 floating screw (+PTPWH2.6)
qa coil spring (insulator)
qs insulator
qd
qf optical pick-up (KSM-215DCP/C2NP)
qj screw (+BVTP 2.6X8)
qg CN101
qh Remove the four solderings of motor.
qk BD board
14
HCD-CPX22/NXM3SECTION 4TEST MODE
[Change-over of AM Tuner Step between 9 kHz and 10 kHz]• A step of AM channels can be changed over between 9 kHz
and 10 kHz.
Procedure:1. Press ?/1 button to turn the set ON.2. Select the function “TUNER”, and press [TUNER/BAND]
button to select the BAND “AM”.
3. Press ?/1 button to turn the set OFF.
4. Press x and ?/1 buttons simultaneously, and the displayof fluorescent indicator tube changes to “AM 9 kHz step” or“AM 10 kHz step”, and thus the channel step is changed over.
[Cold Reset]• The cold reset clears all data including preset data stored in
the RAM to initial conditions. Execute this mode whenreturning the set to the customer.
Procedure:
1. Press three buttons x , [DIMMER] ,and ?/1simultaneously.
[Switching MD/VIDEO Functions]
Procedure:1. Press the ?/1 button to turn the set ON.
2. Press the ?/1 button while holding the VIDEO (MD)button depressed to toggle between “MD” and “VIDEO.” Theselected mode is displayed.
[Error code indication]
Procedure:1. Press the ?/1 button to turn the set ON.2. Select the “CD” function.
3. Press the x , X , and [DISPLAY] buttons simultaneously.4. The error code is displayed.5. Press the [TUNING +] button to display the next error code.
Press the[TUNING -] button to display the previous errorcode.
[Aging Mode]This mode can be used for operation check CD section and Tapedeck section.
• If an error occurred:The aging operation stops and is displayed status.
• If no error occurs:The aging operation continues repeatedly
1. Aging mode in CD section
Procedure:1. Press ?/1 button on the set ON2. Select the function “CD”
3. Press three buttons x , X , and [DISC 3] simultaneously.The “Aging in” display and aging mode is set.
4. Press [DISC 1] button, starts aging mode of all trays check.5. Press [DISC 2] button ,starts measurement loading time.6. To exit from the aging mode perform [Cold Reset].
1) Error displayDisc error
Display Error
E00D01022 Focus error (No disc)
E00D02022 Sub Q error (Focus is good)
E00D02023 TOC reading error
E00D02014 Access error (Unable within regular time)
Mechanism error
Display Error
E00M__E_0 Error during opening tray
E00M__C_2 EX-CHANGE disc error
E00M__D_0 Error during closing tray
E00M__F_3 EX-OPEN error
E00M__D_5 EX-CLOSE error
E00M__C_2 Chuck-up error
E00M__C_3 Unchucking error
2. Aging mode in Tape Deck section
Procedure:1. Load the tapes into the decks A and B respectively.
2. Press ?/1 button on the set ON3. Select the function “TAPE A”
4. Press three buttons x , X , and [TAPE A/B]
simultaneously, and aging mode is started.5. To exit from the aging mode perform [Cold Reset].
• In the aging mode ,the program is executed in the followingsequence.
Step Operation Display
1 Rewind the TAPE A TAPE A AG-1
2 Rewind the TAPE B TAPE B AG-1
3 Play the TAPE A (t) (2 minute) TAPE A AG-2
4 F•F. (AMS) the TAPE A TAPE A AG-3
5 Play the TAPE A (T) (2 minute) TAPE A AG-4
6 Rewind the TAPE A TAPE A AG-5
7 Play the TAPE B (t) (2 minute) TAPE B AG-2
8 F•F.(AMS) the TAPE B TAPE B AG-3
9 Play the TAPE B (T) (2 minute) TAPE B AG-4
10 Rewind the TAPE B TAPE B AG-5
15
HCD-CPX22/NXM3
[GC Test Mode]• All fluorecent segments and LEDs are tested.• Microprocessor virsion.• Keyboard check.• Display check.
Procedure: 1. To enter the test mode, press the three buttons x , X and
[TUNER/BAND] simultaneously.2. All segments and LEDs (without STANDBY LED) are turned
on.3. Press the [TUNING -] button to increment the microprocessor
software version.4. Press the [TUNING +] button to change the indication for the
microprocessor software version. 3. Press the b B button to set the check mode for the entries
(KEY, JOG, etc.). 4. Press the X button to display the current VACS level.
7. Press the x button to enter the mode to check the display. Ifyou press this button repeatedly, the display will changesequentially as the button is pressed.
8. Press the x , X and [TUNER/BAND] buttons simultaneouslyto set the standby mode.
[CD Service Mode]• This mode can run the CD sled motor freely. Use this mode,
for instance, when cleaning the pick-up.
Procedure:1. Press ?/1 button to turn the set ON.2. Select the function “CD”.
3. To enter the test mode, press three buttons x , X , and [DISC
1] simultaneously.4. The CD service mode is selected.The message ‘‘CD SERVICE
MODE’’ is displayed.5. While holding the [TUNING -] button depressed , to move
the sled to the inside. “SLED IN” is displayed.While holding the [TUNING +] button depressed, to movethe sled to the outside. “SLED OUT” is displayed.
6. Press the [CD SYNC] button so that “LD ON” and “LD OFF”are displayed to switch between Laser ON/OFF.
7. To exit from this mode, perform as follows:1) Move the pick-up to the most inside track.
2) Press ?/1 button to turn the set OFF.Note: • Always move the pick-up to most inside track when exiting from
this mode. Otherwise, a disc will not be unloaded.• Do not run the sled motor excessively, otherwise the gear can be
chipped.
[MC Test Mode] (Amplifier SECTION)• This mode is used to test the function of the amplifier section.
Procedure:1. Press ?/1 button to turn the set ON.
2. To enter the test mode, press the three buttons x , X andz/START simultaneously.
3. Turn [VOLUME] knob to counter-clockwise, the function ofthe equalizer is set to “MIN”.
4. Turn [VOLUME] knob to clockwise, the function of theequalizer is set to “MAX”.
5. Whenever turn [BASS] knob to clockwise, the display switchesas follows.
“TONE MAX” t“TONE MIN” t“TONE FLAT”
6. To exit from this mode, press ?/1 button to turn the setOFF.
[MC Test Mode] (Tape section)• This mode is used to test the functions of the Tape Procedure.
Procedure:1. Press ?/1 button to turn the set ON.
2. To enter the test mode, press the three buttons x , X and z/START simultaneously.3. While holding the [DIMMER] button depressed, turn the ALC
ON.4. Press the z/START button to start REC (recording).5. While recording, press the [TUNING +] button to perform
automatic rewind and automatic playback (for FF version).Also, press the [TUNING -] button to perform automatic rewindand automatic playback (for FR version).
6. Select the function “TAPE A” or “TAPE B”7. Press the [CD-SYNC] button while “TAPE A” or “TAPE B”
is selected, to perform AMS check. “EDG[ ]” is displayed.A number appears inside[ ].
8. To exit from this mode, press ?/1 button to turn the setOFF.
[CD Ship Mode (LOCK) ]• This mode moves the pick-up to the position durable to
vibration. Use this mode when returning the set to the customerafter repair.
Procedure:1. Press ?/1 button to turn the set ON.2. Select the function “CD”.
3. Press x button and [CD] button simultaneously.4. The “STANDBY” display blinks instantaneously, and the CD
ship mode is set.5. To fluorescent indicator tube displays ‘‘LOCK’’.
[CD Ship (LOCK) & COLD RESET MODE]
Procedure:1. Press ?/1 button to turn the set ON.2. Select the function “CD”.
3. Press three buttons x , X and VIDEO (MD) simultaneously.4. The “STANDBY” display blinks instantaneously and CD ship
mode is set.5. To fluorescent indicator tube displays “LOCK” and the set is
reset.
[CD power -manage function]
Procedure:1. Press ?/1 button to the set ON2. Select the function “CD”.
3. Press ?/1 button to turn the set OFF.
4. Press x and ?/1 buttons simultaneously ,and the displayof fluorescent indicator tube changes “CD POWER OFF” or“CD POWER ON”.
5. Press ?/1 button to turn the set OFF.
16
HCD-CPX22/NXM3
[DISC Tray Lock]
Procedure:1. Press ?/1 button to the set ON.2. Select the function “CD”.
3. Press x and CD Z buttons simultaneously for 5 seconds.And the displays of fluorescent indicator tube changes to“LOCKED” or “UNIOCKED”.
4. Press ?/1 button to turn the set OFF.
[CD Repeat 5 Times Limit Release Mode]
Procedure:1. Press ?/1 button to turn the set ON.2. Select the function “CD”.
3. Press three buttons x , X and [CD SYNC] simultaneously.4. The message “LIMIT OFF” is displayed.
5. Press ?/1 button the set OFF.
[AMP TEST MODE]
Procedure:1. Press ?/1 button to turn the set ON.
2. To enter the test mode, press three buttons x , X and [DSGX]
simultaneously.3. Display will changes ‘‘VACS ON’’ to ‘‘VACS OFF’’.
4. Press ?/1 button to turn the set OFF.
17
HCD-CPX22/NXM3
SECTION 5MECHANICAL ADJUSTMENTS
SECTION 6ELECTRICAL ADJUSTMENTS
Precaution1. Clean the following parts with a denatured alcohol-moistened
swab:record/playback heads pinch rollerserase head rubber beltscapstan idlers
2. Demagnetize the record/playback head with a headdemagnetizer.
3. Do not use a magnetized screwdriver for the adjustments.4. After the adjustments, apply suitable locking compound to
the parts adjusted.5. The adjustments should be performed with the rated power
supply voltage unless otherwise noted.
Torque Measurement
3.06 N • m to 6.96 N • m
FWD CQ-102C 31 to 71 g • cm
(0.43 – 0.98 oz • inch)
FWD0.19 N • m to 0.58 N • m
back tensionCQ-102C 2 to 6 g • cm
(0.02 – 0.08 oz • inch)
3.06 N • m to 6.96 N • m
REV CQ-102RC 31 to 71 g • cm
(0.43 – 0.98 oz • inch)
0.19 N • m to 0.58 N • mREVCQ-102RC 2 to 6 g • cmback tension
(0.02 – 0.08 oz • inch)
6.96 N • m to 14.02 N • m
FF/REW CQ-201B 71 to 143 g • cm
(0.98 – 1.99 oz • inch)
9.80 N • m
FWD tension CQ-403A 100 g or more
(3.53 oz or more)
9.80 N • m
REV tension CQ-403R 100 g or more
(3.53 oz or more)
Mode Torque meter Meter reading
0 dB=0.775 VDECK SECTION
1. Demagnetize the record/playback head with a headdemagnetizer.
2. Do not use a magnetized screwdriver for the adjustments.3. After the adjustments, apply suitable locking compound to the
parts adjust.4. The adjustments should be performed with the rated power
supply voltage unless otherwise noted.5. The adjustments should be performed in the order given in
this service manual. (As a general rule, playback circuitadjustment should be completed before performing recordingcircuit adjustment.)
6. The adjustments should be performed for both L-CH and R-CH.
7. Switches and controls should be set as follows unless otherwisespecified.
• Test Tape
RECORD/PLAYBACK HEAD AZIMUTH ADJUST-MENT
DECK A DECK B
Note: Perform this adjustments for both decksProcedure:
1. Mode: Playback
Tape Signal Used forP-4-A100 10 kHz, –10 dB Azimuth Adjustment
set
MAIN boardCN304Pin 1 (L-CH)Pin 3 (R-CH)
MAIN boardCN304Pin 2 (GND)
+–
level meter
test tapeP-4-A100(10 kHz, –10 dB)
18
HCD-CPX22/NXM3
2. Turn the adjustment screw and check output peaks. If the peaksdo not match for L-CH and R-CH, turn the adjustment screwso that outputs match within 1dB of peak.
3. Mode: Playback
4. After the adjustments, apply suitable locking compound tothe pats adjusted.
Adjustment Location: Playback Head (Deck A).Record/Playback/Erase Head (Deck B).
Screwposition
L-CHpeak
within1dB
Outputlevel
L-CHpeak
R-CHpeak
within1dB
Screwposition
R-CHpeak
MAINboardCN301set
test tapeP-4-A100(10 kHz, –10 dB)
pin 3
oscilloscope
L-CH
R-CH
V H
waveform of oscilloscope
in phase 45° 90° 135° 180°
good wrong
pin 2
pin 1
L
R
CD SECTION
Note:1. CD Block is basically designed to operate without adjustment.
Therefore, check each item in order given.2. Use YEDS-18 disc (3-702-101-01) unless otherwise indicated.3. Use an oscilloscope with more than 10MW impedance.4. Clean the object lens by an applicator with neutral detergent
when the signal level is low than specified value with thefollowing checks.
S-curve CheckConnection:
Procedure:1. Connect an oscilloscope to test point TPO102 (FE1) and TP
117(VC) on the CD board.2. Turn the power on.3. Put the disc (YEDS-18) in and turned power switch on again
and actuate the focus search. (actuate the focus search whendisc table is moving in and out)
4. Check the oscilloscope waveform (S-curve) is symmetricalbetween A and B. And confirm peak to peak level within 2.4± 1 Vp-p.
S-curve waveform
Note:• Try to measure several times to make sure than the ratio
of A : B or B : A is more than 10 : 7.• Take sweep time as long as possible and light up the
brightness to obtain best waveform.
Checking Location: CD board (SIDE B) (See page 20.)
+–
CD board
TPO102 (FE1)TP117 (VC)
oscilloscope
A
B
symmetry
within 2.4 ± 1 Vp-p
forwardreverse
19
HCD-CPX22/NXM3
RFAC Level CheckConnection:
Procedure:1. Connect an oscilloscope to test point TP124 (RFAC) and TP
117(VC) on the CD board.2. Turn the power on.3. Put the disc (YEDS-18) in to playback the number five track.4. Confirm that oscilloscope waveform is clear and check RFAC
signal level is correct or not.Note: A clear RFAC signal waveform means that the shape “◊” can be
clearly distinguished at the center of the waveform.
RFAC signal waveform
Checking Location: CD board (SIDE B) (See page 20.)
E-F Balance CheckConnection:
Procedure:1. Connect an oscilloscpe to test point TPO103 (TE1) and TP117
(VC) on the CD board.2. Turn the power on.3. Select the function “CD”.
4. Press three buttons of [ENTER], M , and[SURRUUND MODE] simultaneously to set the CD servicemode.
5. Put the disc (YEDS-18) in to playback the number five track. 6. Press the . button. The message “TRAVERSE” is
displayed. (The tracking servo and the sledding servo areturned OFF)
7. Check the level B of the oscilliscope's waveform and the A(DC voltage) of the center of the Traverse waveform.Confirm the following :A/B x 100 = less than ± 22%
Traverse Waveform
8. Press the . button. The message “TRAVERSE” isdisplayed. (The tracking servo and sledding servo are turnedON)Confirm the C (DC voltage) is almost equal to the A (DCvoltage) is step 5.
9. To exit from this mode, perform as follows.1) Move the optical pick-up to the most inside track.
2) Press three buttons of x , [CLEAR], and [DISPLAY]
simultaneously. (cold reset)Notes:
• Always move the optical pick-up to most inside trackwhen exiting from this mode. Otherwise, a disc will notbe unloaded.
• Do not run the sled motor excessively, otherwise the gearcan be chipped.
Traverse Waveform
Checking Location: CD board (SIDE B) (See page 20.)
+–
CD board
TP124 (RFAC)TP117 (VC)
oscilloscope
VOLT/DIV: 200 mVTIME/DIV: 500 ns
level: 0.9 ± 0.4 Vp-p
+–
CD board
TPO103 (TE1)TP117 (VC)
oscilloscope
0V
B
level: 1.0 ± 0.5 Vp-p
Center of the waveform
A (DC voltage)
0V
Tracking servoSled servo
ON
C (DC voltage)
Tracking servoSled servo
OFF
20
HCD-CPX22/NXM3
Checking Location:
– CD BOARD (SIDE B) –
TP117 (VC)
TP124 (RFAC)
JPO103 (TE1)
JPO102 (FE1)IC101
HCD-CPX22/NXM3
2121HCD-CPX22/NXM3
• WAVEFORMS
– MAIN BOARD –
IC401 0 XC-IN
VOL/DIV : 0.5 V ACTIME/DIV : 2.0 µsec
2 IC401 qg X-IN
VOL/DIV : 0.5 V ACTIME/DIV : 50 nsec
2 IC703 6
VOL/DIV : 1 V ACTIME/DIV : 50 nsec
1
1.5Vp-p
32.768KHz
1.5Vp-p
16MHz
2Vp-p
12.288 MHz
– BD BOARD –
IC101 wa TEI
VOL/DIV : 0.2 V ACTIME/DIV : 0.2 msec
2 IC101 wd FEI
VOL/DIV : 0.1 V ACTIME/DIV : 1 msec
3 IC101 ra RFACO
VOL/DIV : 0.2 V ACTIME/DIV : 0.5 µsec
1
49.152MHz
4Vp-p
– S-MASTER BOARD –
IC705 rk XFSOIN
VOL/DIV : 2 V ACTIME/DIV : 20 nsec
1
0.15Vp-p
0.4Vp-p
0.96Vp-p
SECTION 7DIAGRAMS
For schematic diagrams.Note:• All capacitors are in µF unless otherwise noted. (p: pF)
50 WV or less are not indicated except for electrolyticsand tantalums.
• All resistors are in Ω and 1/4 W or less unless otherwisespecified.
• % : indicates tolerance.• f : internal component.• 2 : nonflammable resistor.• 5 : fusible resistor.
• C : panel designation.• A : B+ Line.• B : B– Line.• H : adjustment for repair.• Voltages and waveforms are dc with respect to ground
under no-signal conditions.no mark: TUNER (FM/AM)( ) : CD PLAY< >: TAPE PLAY[ ]: TAPE REC
* : Impossible to measure• Voltages are taken with a VOM (Input impedance 10 MΩ).
Voltage variations may be noted due to normal produc-tion tolerances.
• Waveforms are taken with a oscilloscope.Voltage variations may be noted due to normal produc-tion tolerances.
• Signal path.F : TUNER (FM/AM)E : TAPE PLAY (DECK A)d : TAPE PLAY (DECK B)G : RECORDJ : CD PLAY (ANALOG OUT)c : CD PLAY (DIGITAL OUT)
• AbbreviationE3 : 240V AC Area in E modelE51 : Chilean and Peruvian modelEA : Saudi Arabia mdoelRU : Russian model
Note: The components identified by mark 0 or dotted linewith mark ! are critical for safety.Replace only with part number specified.
(The other layers' patterns are not indicated.)
• Indication of transistor.
• AbbreviationE3 : 240V AC Area in E modelE51 : Chilean and Peruvian modelEA : Saudi Arabia mdoelRU : Russian model
Caution:Parts face side: Parts on the parts face side seen from(Side A) the parts face are indicated.Pattern face side: Parts on the pattern face side seen from(Side B) the pattern face are indicated.
C
B
These are omitted.
E
Q
B
These are omitted.
C E
Q
B
These are omitted.
C E
Q
Note on Printed Wiring Boards:Note:• X : parts extracted from the component side.• : Pattern from the side which enables seeing.
7-1. CIRCUIT BOARD LOCATION
MAIN board
PANEL board
DISC SW board
VOL board
HP boardS-MASTER board
switching regulator
SW(2) board
SW(1) board
MOTOR board
SENSOR board
ENCODER boardBD board
RELAY board
SP OUT board
HCD-CPX22/NXM3
2222HCD-CPX22/NXM3
7-2. BLOCK DIAGRAM – CD SERVO SECTION –
OPTICAL PICK-UPBLOCK
(KSM-215DCP)
LDDRIVER
+1.7V+3.3V
LD
GND
FOCUSCOIL
F+
F
T+
TTRACKING
COIL
X17116.9MHz
IC251SL/SP MOTOR
DRIVER
RF AMP
16
7
15
17
18
VR
PD
19
20
21
22
5
30
3
24MUTE
CH2OUT-F
CH1FIN
CH1RIN
CH2FIN
CH3FIN
OPIN+
CH2OUT-R
CH1OUT-R
CH1OUT-F
CH4OUT-R
CH4OUT-F
CH3OUT-F
CH3OUT-R
M
M
M101(SPINDLE)
M102(SLED)
VC
VCC
A
B
C
D
E
F
DETECTOR
A
B
E19
F20
LD36
PD37
TFDR11
FFDR13
SFDR9
MPD6
95XTACN
100XRST
102DATA
104XLAT
105CLOCK
AOUT2
AOUT1
DOUT
61PCMDI
62LRCKI
63LRCK
65PCMD
IC301DIGITAL
SIGNAL PROCESSOR
2140
SDO011
LRCKIA16
SFSY/LRCKIB19
SDIO14
77 XTAO
78 XTAI
55VDD
VDD
VDDM
26
27
C28
D29
107SENS
XTACN
XRST
DATA
XLT
CLOCK
SENS
TRDR12
29CH3RIN SRDR
CH2RIN FRDR
66BCK
60BCKI
BCKIA15
SBSY/BCKIB18
6
+3.3V
8
5 1
3STANBY
36PO11/BUCK/AD1
8MIACK7MICK
6MIDIO
4MICS
5MILP
2RESET
115SCOR SCOR
REG
MP3STB
MP3REQMIACK
MICKMIDIO
MILP
MICS
MP3RST
SCOR
SENSCLOCK
XLT
DATA
XRST
XTACN
SCOR
SENSCLOCK
XLT
DATA
XRST
XTACN
DOUT
ROUT
LOUT
A MAINSECTION(Page 24)
B TUNER/TAPE DECKSECTION(Page 23)
IC751 (DISC SENSOR)Q751
ROTARYENCODER
(MD)
ROTARYENCODER(ST U/D)
IC701LD/ST MOTOR DRIVER
IC711U/DOTOR DRIVER
42
97
RINFIN
OUT1OUT2
42
97
RINFIN
OUT1OUT2
DMAINSECTION(Page 24)
M761(LD/ST)
M762(U/D)
S781
(SUB TRAY OUT)
(SUB TRAY OUT)
OPENMAIN TRAY
OPEN/INCLOSE
S731
S761
S721
SENSE SWITCH
S771
M
M
D+3.3V
LD/ST MTR NEGLD/ST MTR POS
BU U/D MTR NEGBU U/D MTR POS
CN701
SW3 SUB TRAY OUTSW2 SUB TRAY OUTSW4SUB TRAY OUTSW1 SUB TRAY OUT
MD-E4MD-E3MD-E2MD-E1
ST-E4ST-E3ST-E2ST-E1
D.SEMSOR
CN201
86
81
71
10
14
XRST100
113GFS
2FOK
1
3
114C2P0
IC303
Q10
IC101
• Signal pathJ : CD PLAY (ANALOG)c : CD PLAY (DIGITAL)
HCD-CPX22/NXM3
2323HCD-CPX22/NXM3
7-3. BLOCK DIAGRAM – TUNER/TAPE DECK SECTION –
TUNER
AEP, UK
AEP, UK
R-CH Q25,26Q270
R-CH
L OUT
R OUTCD SERVOSECTION(Page 22)
D OUT
RDS INTRDS DATA
L OUTR OUT
ST-MUTETUNERST-CE
ST D OUTST D INST CLK
STEREO
DECK-A
DECK-B
L
R
HP2
HP1
L
R
HE
HRP2
HRP1
TAPE
F REC
B SHUTA HALFA PLAYB PLAY
A HALFA PLAYB PLAY
R-RECB HALF
A SHUT
CAPM+
A TRIG+
B TRIG+
R-CH
R-CH
Q303Q314,315
Q301,302Q311-313
Q104Q31,22R-CH
L
RVIDEO(MD)
MECHANISM DECK
64
61
66
27
18
49
CN371
IC301
18505152535455
63
5
10
3
11
171819
26
1516
2534789
2221
REC/PBSWITCH
MUTESWITCHDIGITAL
OUT
REC/PBSWITCH
BIASOSC
Q318T301
Q316,317BIAS
REC/PB
BIASSWITCH
TC RECMUTE
12
CAP MDRIVE
Q326,327
Q323,324
Q321,322A TRIGDRIVE
9091
86
89
87
88
67 468 2669 25
65
93
97100
92
LINE MUTE
A MUTE
RDS-DATARDS-INTST-MUTETUNEDST-CE
ST-DINST-CLK
B HALF
MAIN TRANS-OUT
STBY RELAY
CLKDATA
INT
I/O EXP CLK
M16537 CLK
M16537 DATA
SPEC-INVACS INAMS IN
I/O EXP LAT
I/O EXP DATYA INI/O EXP DATA OUT
LATCH
ADC-POWR
S-MASTER
ENABLE
SC SHUTSCDT
INTISCLATCH
P-DOWN
CLK
DATA
D182
/RST
A SHUT
A TRIG
B TRIG
CAPM-CNT1
TC REC MUTE
B SHUT
ON/OFF(SWITCHING REGULATOR)
D+3.3V
ST-DOUT
8081
616059585756
1314
19
876
20212223
18
17
9
L-CH
R-CH
R-CH
Q21,22Q1
Q27,28Q71
J1063PHONES
P-DOWN
FR-OUT
FL-OUT
/RSTINIT
SCLATCHSCSHIFT
SCDTPGMUTE
SOFTMUTENSPMUTE
OVF/OTW
SD
63
62
71
70
68 67 66 65
7 8 11 53 51 50 48 34 35
R-CH
Q341-343Q103Q29,30
Q140Q33,34
SELECTOR
R-CH
AMSDPL-2
42 41 37
3 1
8
S2
FL
CLK DATA
CLK DATAEQ
MD BUSTONE
TRE
AMSMUTE
AMSBUFFER
PB MUTE
LEDSWITCH
LEDSWITCH
AMS-MUTESTEREO
Q1026
D1021
D1001-1005
Q1001-1005
B PLAYA PLAYA HALF
CLK
LED 9V
VCC
LATCHDI 1DO 2
MUTE
IC971I/O EXPANDER
IC951I/O EXPANDER
IC401 (1/2)SYSTEM CONTROL
IC101INPUT SELECT SWITCHELECTRICAL VOLUME
IC3BUFFER
REC/PBBIAS
SDSD/OTWOVF
OVER TEMP
PROTECT HP IN
HALF PLAY
AMS MUTEDISC1
DISC2DISC3DISC4DISC5
LATCHCLK
DI 1DO 2CLK
LATCHNSP
SOFT HPPG
TA MUTEHP MUTE
DATA 1DATA 2
LATCHCLK
DATA1DATA 2CLKLATCHNSP MUTESOFT MUTEPG MUTE
DATA 1DATA 2
OVER FLOW
MUTESWITCH
Q8
AUDIO +9V
HP MUTESWITCH
B TRIGDRIVE
SURR
3
IC903
REG 1
3
IC901
REG 1
3
IC902
REG 1
3
Q906
UNREG+5V
SWITCHINGREGULATOR
UNREG+12V
D+3.3V
CD+3.3V
AUDIO+9V
M+9VLED9V
REG 1
MCUI/F
B
CS-MASTERSECTION(Page 25)
REG
• R-ch is omitted due to same as L-ch.• Signal path
K : TUNER (FM/AM)E : PLAYBACK (DECK A)d : PLAYBACK (DECK B)G : RECORDJ : CD PLAY (ANALOG)c : CD PLAY (DIGITAL)
HCD-CPX22/NXM3
2424HCD-CPX22/NXM3
7-4. BLOCK DIAGRAM – MAIN SECTION –
28MP3STB
CN371
IC401 (2/2)SYSTEM CONTROL
IC1020DISPLAY CONTROL/KEY CONTROL
MP3REQMIACK
MICKMID10
MILPMICS
HP3RSTCD SERVOSECTION(Page 22)
SCORSENS
CLOCKXLT
DATAXRST
XTACN
MP3STBMP3REQMP3 ACKMP3 CKMP3 DATA OUTMP3 LPMP3 CSRESETSCORSENS
FL-DATAFL-CLKFL-CS
FL-RESET
CD-CLKXLTCD-DATAXRSTXTCN
SIRCD
AD-KEY2
AD-KEY1
JOG2-A
JOG1-A
VOL-A
POWER KEY
DISPLAY KEY
XC-IN
X-OUT
XC-OUT
X-IN
31375213219212324222526
CN372
858483
33 LD-ST MTR POSBU U/D MTR NEGBU U/D MTR POS
SW3 SUB TRAY OUTSW3 SUB TRAY INSW4 TRAY CLOSE SWSW1 TRAY OPEN SW
ST-E1ST-E2ST-E3ST-E4MD-E1MD-E2MD-E3MD-E4D,SENSER
EVER+4V
EVER+4V
4734463545
CDN-MOT-NEG-1(LD)CDN-MOT-POS-1(LD)
CDN-MOT-NEG-2(U/D)CDN-MOT-POS-2(U/D)
CDN-MAIN-SW-OPEN(SW2)CDN-MAIN-SW-CLOSE(SW4)
CDN-SUB-SW-OPEN(SW2)CDN-SUB-SW-CLOSE(SW3)
CDN-ENC-B-3(MDM4)CDN-ENC-B-2(MDM3)
CDN-ENC-B-1(MDM2)CDN-ENC-B-0(MDM1)
CDN-ENC-A-3(STE4)CDN-ENC-A-2(STE3)
CDN-ENC-A-1(STE2)CDN-ENC-A-0(STE1)
DISC SENS
LED-STANDBY
RESET
AC-CUT
48 LD/ST MTR NEG
3644
43384239
37
414075
72
12
20
OUTSIRCS
IC1050
41
KEY2-1KEY2-2
S1043S1001-1005
S1051
KEYNETWORK
94
ROTARYENCODER
ROTARYENCODER
ROTARYENCODER
TREBLE 78JOG2-B79
S1050
76JOG1-B77
S1052
S1042
70VOL-B71
74
95
BASS
BASS
X40136.768kHz
X40216MHz
VOLUME
S1021-1027,1029-1031S1032-1036
REMOTECONTROLRECEIVER
KEYNETWORK
S102873DISPLAY
10
11
13
15
876
82 5
51I
15
3•2•1•
64I
57
56•
55
4
54
LEDSWITCH
Q1041
D1050
IC391RESET
Q391
3 1LEVEL
DETECT
GREIDDRIVE
Q1021
GRIDDRIVE
Q1022
55 GRIDDRIVE
Q1023
SDATASCKCSRESET
SEG00I
SEG35
DEG01
FL1020FLUORESCENT
INDICATORTUBE
F1
F2
DEG11
DEG12/SEG36
DEG13/SEG37
DG00
DIG14SEG38
VF1
VP D/D CON+9V
Q1024T801D1023-1026
VF2
VPRECT
BIASOSC
A
DCD SERVOSECTION(Page 22)
HCD-CPX22/NXM3
2525HCD-CPX22/NXM3
7-5. BLOCK DIAGRAM – S-MASTER SECTION –
1
22
27
/OTW/SD
CN700
/RST
L-INR-IN R-IN
P-DOWNINIT
SCLATCHSCSHIFT
SCDTPGMUTE
SOFTMUTEMSPMUTE
OVF
DOUTBCK
SCKI
OUT BOUT B
OUT AOUT A
LRCK
OUTL1
OUTL2
OUTR1OUTR2
L-IN DATABCK
INIT
XFSD IN
SCLATCHSCSHIFTSCDTPGMUTESOFTMUTENSPMUTEFLAGL OVFOVF FLAGR
/RST/SD/OTW
BP
AP
LRCKXFSI IN
R-INP-DWN
2327
21
1920
18
2425
48
15
TM504IC707
DIGITAL POWER AMPIC705
DATA CONVERTER
L
R+
R-CHR-CH
L+
L-
R-
4
IC709
X702
2 1
IC710A+5VREG3
X701
IC703
IC701A/D CONVERTER
13
11
9
2
3029
2625
17
134
15
64
1110
31302936
PROTECT
Q701
A+5VA+9V
D+3.3V
OVER LOADDETECT
Q702,703
SWITCHINGREGULATOR
R
SPEAKER7 1
6 2
1
IC706D+3.3V
REG3
+1.8V 5
IC7041.8VREG4
CTUNER/TAPE
SECTION(Page 23)
• R-ch is omitted due to same as L-ch.• Signal path
F : AUDIO
HCD-CPX22/NXM3
2626HCD-CPX22/NXM3
7-6. PRINTED WIRING BOARD – BD SECTION – • See page 21 for Circuit Boards Location.
C10
C260
C14
C15
C16
C18
C11
R405
C316
R354
R353
R352
R351
R302
R253
C315
R191
R172
R171
R162
R313
X171
R121
R12
R11
R10Q10
C116
C312
C184
C183
C303
C302
C305
C259C258
C257
C255
C203
C196
C195
C201
C182
C171
C172
C308
C151
C134
C125
C314
C123
R165
R13
C17
FB30
1
C318
R201
C174
R173
R205
C209
C210
12(12)1-860-502-
BD BOARD (SIDE A)
E
R419
R412
R411
R410
R409
R408
R407
R406
R404
R403
R402
1R401
R305
R303
R301
R252
JPO103 (TE1)
JPO102 (FE1)
TP117(VC)
TP124(RFAC)
R251
R182
R181
R163
R151
R143
R142
R141
R133
R132
R131
R114
R113
R112
R111
R307
C313
C311
C310
C309
C307
C306
IC251
C252
C251
C194
C181
C320
S101(LIMIT)
IC101
C163
C162
C143
C142C141
C133
C132
C131
C124
C111
C122
C115
C114
C113
C112
IC301
C185
C186
R306
CN101
IC303
CN20
1
C206
36 28 27 19
1 9 10 18C317
R203
R161C161
C211
C212
R204
C213
13
4 5
M101SPINDLEMOTOR
M102SLED
MOTOR
M
M
BD BOARD (SIDE B)
12(12)1-860-502-OPTICAL PICK-UP
BLOCK(KSM-215DCP)
AMAIN
BOARD(Page 30)
16
17
32 49
48
64
1
33
27
2 3 4 5 6 7 8 9 10
A
1
B
C
D
E
FRef. No. Location
IC101 D-8IC251 C-6IC301 C-8IC303 B-8
Q10 E-4
• SemiconductorLocation
HCD-CPX22/NXM3
2727HCD-CPX22/NXM3
7-7. SCHEMATIC DIAGRAM – BD BOARD –
TP165
TP166TP178
TP14
4TP
147
TP15
3
TP186
TP187
TP167
TP16
0TP
162
TP177
TP14
5
TP14
8
TP12
1
TP12
2
TP12
3
JPO004
JPO10
TP25
0
TP30
1
TP302TP303
TP30
4TP103
TP104
TP105
TP14
6
JPO102
JPO103
TP420
TP421
TP422
TP423
TP424
TP42
6
TP427
TP428
TP429TP430
TP431
TP432
TP433
TP436TP401
TP407TP406TP405TP404TP403TP402
TP408
TP410TP434
TP417TP416TP415TP414TP413TP412TP419
TP411
TP435
TP409
TP19TP18TP17TP16TP15
TP102TP14TP13TP12TP11TP10
TP25
3TP
252
TP25
1
IC301
TP12
5
TP12
4
TP14
2
TP14
9
C308
C309
R303
C310
C311R306
C312IC303
FB301 C302 C303C305
CN201
R205
R411R410R409R408R407R406R412
C213
C212 C211
C209
C203
R201
C201C210 R162
R165 C163
R163
C196
C260 C255
C252
C257
M101
M102
IC251
R253
C258 C259R252
R251
C251
C195
C115
R111
C116
R112
R114R113
C111C112C113C114
CN101
C15
C10
C11
Q10
C16 R13
R10
R11
C17R12
C18
C122
R121
C123
C124
C134C142
R143
C132
C133
R133
R132
C141
R142
R141
C143
R151
C151
C131
R131
R352
R353R354
C161
C174
R173
C162
R171C172
X171
C171
R172
R161
R182
R181C185
C186
C181
C182 C184
C183
C194
R351
R302
C313
C314
C316
C315R313
C317
R305
R301
R401
C318
R203
C320
C306
R405R404
R419R403R402
R307C307
C125
IC101
R191
R204
MIRR
DFCTFOK
XUGF
XPCK GF
S
MVDD
MGND
LOCK
WDC
KCO
UT
VC
WFC
K
SBSO
RFDC
O
MDP
APC
SP-
LRCK
PCMD
BCK
C2PO
FEI
TEI
AGND
DGND
MP3GND
IOP1
IOP2
SW-
PCMDI
FRDRFFDR
TRDRTFDR
MDP
MP3VDD
AVDD
MP3STB
MICSMILPMIDIOMICKMIACKMP3REQ
MP3RST
ROUTAVDD
SCORSENSCLKXLTDATAXRSTXTCN
LOUT
DVDD
DOUT
F-T-F-F+PD
FCBADE
SL-
SL+
SP+
TC94A34FG-002
RFAC
I
RFAC
O
EXCK
474V
0.1
100k
0.1
0.10
0.1BH15FB1W
0.1 0.1 2204V
27P
0
100100100100100100100
22p
22p 220p
0.01
10010V0
10010V
0.1 47k
0.1
100
0.1
22010V
0.1
0.1
0.1
BA5947FM(HSOP28)
10k
0.1 0.122k
10k
0.0068
0.1
0.1
1k
100 10V
15k
15k1k
0.0033470p0.0033470p
16P
0.1
10
10
2SB1690K
1 1
3.3
0
2204V100k
0.001
0.1
15k
0.1
330p
0.10.0015
3.3k
0.47
0.01
180k
10k
0.1
1k
4.7k
0.1
0
10010V
100p
1M
100
100100
0.1
0.1
0
0.1
47027p
16.9MHz
22p
1M
100
100
1002200p
2200p
0.1
0.1 226.3V
226.3V
0.1
100
10k
0.1
474V
0.0022
0.1220
0.01
100k
100k
100
0.01
0
0
0.1
100100
100100100
10k0.1
0.1
CXD3059AR
0
0
SRDRSFDR
D3.3
V
MDP
SQSO
DDC2
.5V
DDC2.5V
DVSS
DVSSD3.3V
A3.3
V
A3.3VAVSS
DOUT
LOUTROUT
DVSS
D3.3
VAV
SSA3
.3V
VSSX
VSSP
VSS
A3.3
V DD
C
A3.3V
D3.3V
DGND
AGND
EF
F
EDABC
MIACKMICK
MIDIOMILP
MICS
SCOR
SENS
CLOC
K
DATA
XRST
XLTCLOCK
SENSSCOR
XRST
MP3REQ
DATA
MP3STB
XTACN
XTAC
N
MP3STB
DCBA
MP3RST
XLT
MP3REQ
MIACKMICK
MIDIOMILPMICS
MP3RST
*
BOARD(Page 33)
MAIN
• See page 41 for IC Pin Function Description.
HCD-CPX22/NXM3
2828HCD-CPX22/NXM3
7-8. PRINTED WIRING BOARD – CD MECHANISM BOARD – • See page 21 for Circuit Boards Location.
JW701
S761(SUB TRAY OUT)
R753R754R751
C702
JW71
3
Q751
R752
R755
JW71
2
JW709
JW710JW711
JW714
IC71
1R7
12
R711
C701
JW702R701
R702
CN761
CN751
JW705
JW707JW708
JW706
IC701
CN70
5
CN731
CN771CN701
C703
IC751
JW703
JW704
S721(MAIN TRAY IN/OUT)
S731(SUB TRAY N)
S771ROTARY ENCODER
(MD)
S781ROTARY ENCODER
(ST U/D)
CN721
JW715
JW716JW718
JW71
9
JW720 JW71
7
CN70
6
CN70
2
CN707
CN703
C762
C761
D701D7
11
MOTOR BOARD
SENSOR BOARD
SW(2) BOARD
SW(1) BOARD
ENCODER BOARD
RELAY BOARD
11(11)1-861-241-
11(11)
1-861-242-
11(11)1-861-243-
11(11)1-861-245-
11(11)
1-861-244-
11(11)1-861-240-
MAIN BOARD(Page30)
B
M761(LD/ST MOTOR)
M762(BU U/D MOTOR)
43
21
G
1
1
1
1
11
1
1
6
2
3
3
3
3
1
1
2
2
3412
34
G
G
9
9
20
21
16
2 3 4 5 6 7
A
1
B
C
D
E
F
Ref. No. Location
D701 D-4D711 D-4
IC701 D-4IC711 E-3IC751 B-6
Q751 D-2
• SemiconductorLocation
HCD-CPX22/NXM3
2929HCD-CPX22/NXM3
7-9. SCHEMATIC DIAGRAM – CD MECHANISM BOARD –
M761
M762
S761
S731 CN731 CN703
IC751
CN751 CN705
R711R712
D711
IC711
D701
C762
C761 R702
R701
C701
IC701
CN702 CN721S721
CN701
C702
R751
R754Q751
R753
R752R755
CN707 CN771
S771
S781
CN706CN761
RF500TB
RF500TB
(SUB TRAY OUT)
(SUB TRAY IN) 2P 2P
RPR-359F
3P 3P
680100
MTZJ-T-77-4.3A
BA6956AN
MTZJ-T-77-4.7B
0.01
0.01 100
680
4716V
BA6956AN
3P 3P(MAIN TRAY
IN/OUT)
21PIN
1016V
91
12k2SC2785-HFE
10k
10k10k
5P 5P
ROTARY ENCODER(MD)
ROTARYENCODER
6P6P
ST-E2ST-E3ST-E4
ST-E1
ST-E4ST-E3ST-E2ST-E1
HCD-CPX22/NXM3
3030HCD-CPX22/NXM3
7-10. PRINTED WIRING BOARD – MAIN BOARD – • See page 21 for Circuit Boards Location.
E
E
E
EE
EEE
E
E
E
E
E
E E
E
R339
R338
R337
R340R333
R330R336R332
R335
R331R334
R18
R208
C205
C255
R206
R256
R220
R221
C223
R222JR200
R231
R232
R298R2
94
Q270
R272
R299
R270
R273
R296
R275
Q271
JR115
R325R326
R324
Q323
C324
C323D322
Q321
R321R322
R323
C322
C321D321
Q326
R327
R329
R328
JR10
8
Q26
R29
R28
R27
Q25
JR10
7JR
109
JR106
R123
Q153
R159
R161 R180
R160Q140
R133
C351
C301
R162
C196
R129
R122
C131
R121
R132
R131
R151
C303
C353
R164
R163
C157C1
60 R153C1
58
R154
R155
C161
IC101
R158
C123
R127
4041
64 65
180
25 24C1
74C1
73
C110R105
C108
C107
R104
R189
R101
C111
JR11
6
R188
R341
R342Q3
41
R343
R345
R344
Q342
Q343
JR11
7
R126
R3
R1
R103
R2
Q1
JR118
JR119
R5
R6Q2
R4Q29
Q30
R33
R35
Q32
Q31
R36
R34
R38
R37
Q33
Q34
C146
R110
Q103
R109
Q316
R314R315
R317
R318
R320
R316
R319
Q314
R303R353
Q353Q303
Q315
R113
R112
R114
R111
R352
Q352
R302
Q302
Q301Q311R312
Q312
Q313
R311
R313 R3
51
Q351
R301
R76R80
R69
R79
R77
Q71Q81
R87
R89R59
R90
R86C90
R60R85R88
R98
R50R75R78
C70
IC3Q22
Q21
R22
R21 R23
JR26
1JR
120
R914
Q906
JR1
L951C952R959R9
58
R957 JR
121
IC951
R955
R954
R953
R968
JR112
JR111
R970
R956 C9
53
R952
C973
C972R984
JR10
4
L971
R450
R449
R243
R241
Q27
Q28
E
ER145
R142
R192
C191 R191
C100
J102C141
R141
R30
R31
R32
L370
R247R246R451
R452
R448
C383
R387
R385
JR11
0
R383
R381
R379
R377
R433
R378
R384
R386
R388
R440
R439
R438
R382
R380
R434
R435
R436R4
37
R441R443R445
EXCE
PT A
EP,U
KR4
55
R442R444R446
31
50
100
81
30
11
80
R447
JR44
9
R453
R454
R416R430
R429R415
R424
R422
R421
R418
R419
JR418
R423
R425
R426
R420
R417
C416
R413R411
R431R432
JR105
FB373
FB372C373
FB37
1
FB37
4
C412
JR101
R391
Q391
R393
D392
R394
C411C410
R409R406
JR10
3
R407D391
R392
R396R405R403R402R401
R404
R395
D393
D394
JR114
JR113
R187
D181
D183
R498 R186
R499
D182
R495
R494
R456 R458
R457
R459 R460
R461
D397
D395
D396 R412
R465
C463
C475R4
70
C476R4
72R4
74R4
77R4
76
R473
R471
R414
R408
R410
R493
R479
R478
R466R467
R482
R483
R468
R469
R484
R486
JR10
2R4
90
R489
R485
R496
R492
R497 C499
C497
IC971
D905
JR123
JR122
JR124
JR125
D904
JR12
6
C148
C198
R39
JR12
7
JR128
R347
IC401
C197
C147
R304
R354
C305
C355
R305
R355
C306
C356
C357
C307R3
06R3
56
R357
R307
R309
R359
C308
C358
Q104
Q154
R102
R152
R118
R168
R119
R169
R915
C35
C32
C40
C41
C368
JW17
1
JW17
2
JW10
3
JW10
2
JW10
6
CN10
9
JW108
JW12
9JW
130
JW12
5
JW15
8
JW16
6JW
165
Q324
JW110JW274
JW10
9
JW11
3
JW11
4
JW11
6
JW11
8
JW11
9
JW12
0
JW12
1
JW476
JW159
JW160
JW23
6JW
150
JW14
9JW
174
JW17
3
JW151
JW143
JW140JW141JW142
JW131
C270
JW13
8
JW137
JW15
4
JW12
6JW
127
JW12
8JW41
8
JW17
5JW
176
CN371
JW136
1
10 20
21 15 15
10
27
C382
JW13
3
JW13
2C3
72
C379
JW13
4
JW14
4JW
145
JW14
6
JW14
8
Q322
JW27
6Q3
27
JW411
JW412JW413
JW105
JW111
JW112
C207C257
C222
JW273
JW474JW480
JW30
5
JW27
8
JW468JW281JW282
JW284JW420
C135C156
C134
C154
C122
C159
C133
C132
C152
C151
C166
C167
CN30
1
C352
C302C1
21C155
C162
C168
C165
C304
C354
C119
CN30
2
C117
C118
C115
C116
JW26
1
JW30
1C3
14C315
T301
C313
C311
C312
Q318
L311
Q317
JW45
4
C101
C102
C106
JW31
2
JW37
8
JW37
9JW
380
JW38
1
C103
C109 C112
C105
C104
JW331
C1
C124
C390
JW31
5
JW42
8
C87
C77JW911
C75
C89
C85
C79
C94
C93
C25
C26
JW47
2JW
309
JW47
1JW
310
JW27
0JW
269
JW26
8JW
267
JW26
6
JW24
6
JW179
JW170
JW152
JW153
JW157
CN11
0
JW163JW164JW162
JW167
JW168JW169
JW177
JW178
C183
JW31
7JW
260
JW19
0
C498
JW397
JW396JW388JW389
JW38
5C2
JW395
JW362
JW39
4
JW482JW481JW354
JW429
C22
C21
JW382JW384JW490
JW90
4
JW500
JW90
3
JW375JW374JW365
JW373
JW371JW376
JW349
JW322JW323
JW351
JW347
JW346JW348JW377
JW8
CN30
4
JW475JW421
JW297
JW42
2JW
423
CN106
JW467
JW31
8JW
319
IC39
1C3
93
C391
C392
X402
X401
JW20
9C417
D373
JW18
9
JW206JW101JW124
CN372
CN401
JW224
C384
JW19
2
JW19
1
D371
JW46
6
D372
JW25
1JW
252
C462
JW40
2JW
405
JW355
JW6 JW3
JW241JW244
JW242
JW48
5
JW42
4
JW404
JW40
6JW40
8JW
409
JW41
0
JW40
3
JW24
5
JW215
JW19
4JW
416
JW19
5JW198
JW199JW200
JW197
CN204
JW202
JW201JW239
C27C28
C370
C142
IC301
JW38
3JW
499
JW45
5JW
483
C192
JW229
JW230
JW231
JW232
JW233JW234
JW235
JW426
JW43
5
JW243
JW9JW7
JW425
3 2 1
17
3 2 1 3 2 1
CN11
2
JW41
4
JW46
4
C901
C902
IC901
C905C906
IC903
C904
C903
JW436
JW489
IC902
C920C919
JW431JW447JW496
JW450JW438JW452
CN101
JW44
3JW
444
JW49
8
JW44
9
C930
JW46
5
JW90
1
JW320
C900
JW49
7
JW902
JW45
3
JW445
JW493JW161
JW442
JW900
EP90
1
JW463
CN30
3
C127
JW48
8
JW5
JW13
9
JW14
7
JW386
JW387JW495
JW10
JW280
JW35
2
JW46
9
JW344
JW343
JW283JW193
JW222
C125
C126
JW25
0JW240
JW216
JW446
JW46
2
CN105JW491
CN10
7
JW214
JW41
5
JW223
JW249
JW205
JW20
3
JW930
JW42
7
JW407
JW43
9
JW35
3
JW20
4
JW401
JW350
15P(AEP,UK)
TUNER
SWITCHINGREG
AC IN
TAPEMECHANISM
DECK
11P(US,E3,E51,EA,RU)
11115
C271
JW29
8
L301
L351
D903
JW334
JW417 JW296
JW363JW366
JW372
JW29
9
C375
JW39
9
Q82
C169
DGNDIC301DIGITAL OUT
J102VIDEO(MD)
OPTICAL3.3VDOUT
11(11)1-861-417-
CHASSIS
CHASSIS
S-MASTER BOARD(Page38)
S-MASTER BOARD(Page38)
H
HP BOARD(Page36)
F
VOL BOARD(Page36)
D
S-MASTER BOARD(Page38)
G
RELAY BOARD(Page28)
BBD
BOARD(Page26)
A
PANEL BOARD(Page34)
E
VOL BOARD(Page36)
C
AEP,UK11PEXCEPTAEP,UK
US,E3,E51,EA,RU15PAEP,UK
AEP,UK
MAIN BOARD
C196
C38
C36
C39
FB80
FB50
FB30
FB34
FB54
FB84
AEP,UK,EA,RU
AEP,UK,EA,RU
AEP,UK,EA,RU
AEP,
UK,E
A,RU
AEP,UK,EA,RU
C37
AEP,UK,EA,RU
E
E
E
E
E
E
E
EEE
E
E
E
E
E
E
E
E
E
EE
E
E
E
E
E
E
I
L
IN
R
R CH
L CHPB HEADHP901
R CH
L CH
HE901ERASEHEAD
HRP901REC/PBHEAD
2 3 4 5 6 7 8 9 10 11 12
A
1
B
C
D
E
F
G
H
J
I
Ref. No. Location
D181 E-7D182 D-6D183 E-7D321 D-11D322 C-11D371 B-5D372 B-5D373 B-6D391 D-6D392 C-7D393 D-7D394 D-7D395 E-5D396 E-5D397 E-5D903 B-10D904 F-2D905 G-4
IC3 I-6IC101 G-8IC301 B-2IC391 C-7IC401 D-6IC901 F-4IC902 F-2IC903 F-3IC951 E-3IC971 D-3
Q1 H-7Q2 I-6Q21 I-5Q22 I-5Q25 E-8Q26 E-8Q27 B-3Q28 B-3Q29 I-6Q30 I-6
• Semiconductor Location
Ref. No. Location
Q31 I-6Q32 I-7Q33 I-7Q34 I-7Q71 I-7Q81 J-7Q82 J-6Q103 I-8Q104 I-8Q140 G-9Q153 G-9Q154 I-8Q270 C-8Q271 C-9Q301 I-9Q302 H-9Q303 I-9Q311 I-8Q312 I-8Q313 I-8Q314 I-9Q315 I-9Q316 J-7Q317 J-8Q318 J-8Q321 C-11Q322 D-11Q323 C-11Q324 C-11Q326 D-11Q327 D-11Q341 F-7Q342 G-7Q343 G-7Q351 I-9Q352 H-9Q353 I-9Q391 D-6Q906 G-4
HCD-CPX22/NXM3
3131HCD-CPX22/NXM3
7-11. SCHEMATIC DIAGRAM – MAIN BOARD (1/3) –
R315
R314
R303
R353
R305 R355
R311 R313
R318 R317R319
C313 R341
R342
R343 R345
C311
R320
R312
R130
C151
C152 C1
54
C156
R122
R151
R111
R153
C312
C305 C355
CN301
CN302
C133
T301
C121 C1
31
C155C122
C308C358
R102
R152
R118
R307
R357
R131
R132
C169
C303
C353
R301
R302
R351
R352
R126
R127
R241
R243
CN304
C117
R113
C147
C125
C126
C167
R163
C197
C148
R112
C118
R114
C198
R162
C168
R164
C119
C116
C146
R109
R33R34
R35R36
R39
R344
C390
C40
C36 C37 C38
R306
R356
L351
C307
C357
L301
C306
C356
R304 R354
C315
C314
R110
CN204
C157
C158 C1
60
C161
C162
R154
R155
R121
C135
R123
C132
R129
C196
R160
R180
R159
C166 R161
C107
C108
C110
C111
C112
C106
C105
R101
C104
C103
C109
R103 R105
R104
C174
R347
C124
C123
R141C141
R142C142
R191 C191 R192 C192
C134R133
C165
C100
R38 R37
C159
FB84
FB54
FB34
FB30
C302
C352
C301
C351FB80
R359
R309
R168
R246
R247
J102
R316
FB50
L311
R298 C101
R294
R119
R169
C115
C173
C102
C127
C35
C304
C354
IC101
Q103
Q301 Q351
Q302 Q352
Q311
Q312
Q313Q314
Q315
Q303
Q353
Q153
Q140
Q104
Q154
Q317
Q316
Q318
Q32 Q34
Q30
Q341 Q342
Q343
Q31 Q29 Q33
4.7k
47k
1k
1k
4.7k 4.7k
10k 10k
47 10k3.3k
4710V
10k
4.7k
22k 10k
0.0068PET
33
10k
100
1050
V 1050
V
1050
V
1050
V
15k
15k
1k
2.2k
0.01PET
0.001B
0.001B
3PPH-L
8PPH-L
0.01
PET
SUMIDA
1M
F
22p
CH
0.1
MF
4.750V
0.01 B0.01 B
47k
47k
100
10k
10k
2.2k
27k
4716V
330pB
330pB
4.7k
4.7k
4.7k
4.7k
220
220
0
0
3P
1 50V
330k
100p CH
100 10V
100 10V
1 50V
330k
100p CH
100p CH
12k
0.01 PET
180
100p CH
12k
0.01 PET
180
4716V
1050V
0.0068B
47k
100k22k
100k22k
0
10k
2250V
0.1
0.1 0.1 0.1
8.2k
8.2k
27mH
330p
330p
27mH
100p
100p
15k 15k
0.0047
0.01 100V
1k
0.02
2B
0.02
2B
0.04
7B
0.00
82B
1050
V
2.2k
10k
2.2M
150
V
1M
0.01PET
15k
0.0068
1k
100
47k
1050V
1k
0.02
2B
0.02
2B
0.04
7B
0.00
82B
1050
V1050
V
0.1
MF
15k
1050
V
1050
V
1050V
2.2k 10k
2.2k
100p
2.2k
10010V
0.1F
1k220p
B 100k10
50V
1k 220pB
100k 1050V
1050V10k
1050V
0.1
22k 100k
1050V
0
0
0
010
50V
1050V
330p
330p0
2.2k
2.2k
100
10k
10k
10
0
1k 1050V
1k
10k
10k
1050V
100p
1050V
10010V
0.1
1050V
1050V
M61537FP
2SC3624APB MUTE
2SC3624A 2SC3624A
2SC3624A 2SC3624A
2SA812
DTC114EKA
DTC114EKADTA114EKA
DTC114EKA
2SC3624A
2SC3624A
2SC3624APB MUTE
2SC3624A
2SC3624A
2SC3624A
RT1P137LBIAS SWITCH
DTC114EKABIAS SWITCH
2SC2001BIAS OSC
DTA114EKA DTA114EKA
DTA114EKA
2SC1623 DTC114EKA
DTC114EKA
DTC114EKA DTC114EKA DTC114EKA
B-1
GND
B-4
ST A
+9V
AUDI
O A+
4.5V
CDM
D+
3.3V
53 B-7
B-6-B
B-5
GND
CDM
D+
3.3V
B-5
100
50
51
52
53
54
55
A5
63
18
81
80B1
9
B18
B17
49
A18
FR
FL
DM-L
DM-R
*
TUNER
AEP,UK
AEP,UK15P
11P US,E3,E51,EA
*CN204
R-CH
L-CH
HEAD
PB
HEAD
REC/PB
HEADERASE
HE901
R-CH
L-CH
(CHASSIS)
R
L
IN
ELECTRICAL VOLUME
INPUT SELECT SWITCH,
REC/PB SWITCH
Q301-303,
Q311-315
(FOR CHECK)
DECK
DECK
A
B
HP901
HRP901
HCD-CPX22/NXM3
3232HCD-CPX22/NXM3
7-12. SCHEMATIC DIAGRAM – MAIN BOARD (2/3) –
C410
R411
R413
R409
R417
X401
R429
R430
R415
R416
R408
R410
R412
R414
R393 R395
R396
C391
C392
C393C1
83
R424
R425
R426
R433
R434
R435
R436
R437
R438
R439
R440
R441
R442
R443
R444
R445
R446
R447
R448
R452
R453
R454
R455
R470
R471
R472
R473
R474
R476
R477
R478
R479
R486
R489
R490
R956
R957
R958
R959
C952
C953
R485
R484
R483
R482
X402
R187
R189
R955
R952
R493
R970
R451
R466
R467
R468
R469
R186
R188
L951
C411
R953
R954
R968
R402
R403
R405
R406
R407
R404
R401 R4
19
R421
R422
R423
R420
R432
R431
R459
R460
R458
R457
R456
R461
R450
R392
R391
JW3
R394
JW5
C973
C972
JW6
L971
R465
CN401
C476
C475
C463C462
C417
C412
C416
C497
C498
C499
R497
R494
R495R498
R499
R492
R496
JR418 R418
JR449
R449
R984
IC951
IC401
IC971
IC391
Q391
D181
D182
D183
D395 D396D392 D393
D394
D397
D391
18p
CH
330k
0
10k
10k
32.7
68K 10
0
100
10k
10k
10k
10k
10k
10k
22k 220
10k
0.1 MF
0.1
MF
1050
V
150
V
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
0.1
F
0.1 F
100
100
100
100
16M
470k
47k
100
100
100
10k
100
10k
10k
10k
10k
0
330
03216
18p
CH
100
100
10k
100
100
100
100
100
100
100 10
0
100
100
1004.7k
100
100
100
100
100
100
100
100
100
22k
10k
4.7k
0.1F
0.1F
03216
100
4PAMP-S
0.01
0.01
0.110010V
10006.3V
0.1
0.1
0.1F
1050V
0.1F
10k
3.3k
3.3k10
10
0 0
0
100
10k
PT8300R
M30622MGN-B28FP
PT8300R
M62703
2SC1623
1SS355
1SS355
1SS355
1SS355 1SS3551SS355 1SS355
1SS355
1SS355
1SS355
B-1
B-2B-3
A-M
UTE
C32
EVER
+4V
GND
53
B-5
B-7
CDM
D+
3.3V
B-8
B-9
TC D
+3.3
V
B-10
GND
CDM
D+
3.3V
B-5
1 2 3 5 7 19 21 22 23 24 25 26 28
32
31
7374777879
4
94
95
86
87
88
89
90
91
100
76 65 63
5758
50
49
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
A8 A9
A10
A11
A12
A17
A19
A20
A21
A22
A23
B7 B8 B9
56
A5
A6 A7
535455 52 51
LATCH
CLK
DATA1
DATA2
DATA1
DATA2
LATCH
CLK
707172
66676869
66 676869
18
596061
82
83
84
85
B19
B18
B17
B22
75
93
A18
81
80
*
*
*R492
1K
2.2K
4.7K
0 AEP,UK
E3,EA
US
E51
1K
4.7K
0
*R496
EA
E3
AEP,UK
I/O EXPANDER
SYSTEM CONTROL
I/O EXPANDER
LEVEL DETECT
(FOR CHECK)
EXCEPT E3,EA
RU150
EXCEPTAEP,UK AEP,UK
EXCEPT
AEP,UK
• See page 44 for IC Pin Function Description.
HCD-CPX22/NXM3
3333HCD-CPX22/NXM3
7-13. SCHEMATIC DIAGRAM – MAIN BOARD (3/3)–
R1
R3
R4
R6
C1
C2
C919C920
R914
C903 C902C904
R22
R21
C901
CN372
R377
R378
R379
R380
R381
R382
R383
R384
R385
R386
R387
R388
C21
C22
R915
C905C906
CN101
CN105
CN106
R76
R85
R75
R77
R87
R78
R88
R80
R79
R89
R69
R59
R60
R50
C89
C85
C75
R90
CN107
R273
R275
C270 R270
R272
R299
R296
C271
JR1
FB371
FB374
CN371
FB373
C382
C900
R323R326R329
R338
R339
R337
JW90
0
C28
C27
R31 R32
R30
C39
CN112
JW93
0
CN109CN110
R86C87
C94R98
C93
C90
C70
JW8
JW7
C375
C372
C373
FB372
C379
C383C384
R335
R332
R336
R330
R333
R340
R334
R331
C324C322
R321R322R324R325
R327R328
R28
C25
R27
C26
C370
L370
C77
C79
C930
R29
JW10
R23
R2
R5
CN303
EP901
IC301
IC902 IC901 IC903
IC3
Q270
Q271
Q906
Q26
Q25
Q28
Q27
Q22
Q21
Q327 Q324 Q322
Q1
Q2
Q321
Q326
Q71
Q81
Q82
D373
D372
D371
D321D322
Q323
D904
D905
D903
2.2k
1k
2.2k
1k
10 50V
10 50V
1050V
1050V
1k
1050V
10010V
10010V
22k
4.7k
0.150V
21P1MMFFC-S
10k
10k
10k
10k
10k
10k
10k
10k
10k
10k
10k
10k
4.750V
4.750V
1k
0.150V
10010V
6PEH-S(2X)
3PEH-S(2X)
19P1.25MMFFC-S
47k
10k
10k
100k
100k
1k
1k
10k
47
47
47
47
47k
47k
10 50V
1050V
1050V
10k
4PAMP-S
2.2k
1k
1050V 2.2k
1k
10k
10k
1050V
0
0
0
27P1MMFFC-S
0
47010V
470016V
1k1k47k
10k
47k
22k
10010V
10010V
22k 100k
4.7k
0.1
5P1.25MMFFC-S
13P1.25MMFFC-S15P
1.25MMFFC-S
47k47010V
10010V
1k
100010V
22p
22p
10006.3V
4706.3V
0.1
0
4706.3V
0.14706.3V
47k
4.7k
47k
4.7k
47k
4.7k
47k
47k
0.00470.0047
2.2k2.2k2.2k2.2k
2.2k2.2k
22k
4.750V
4.7k
4.750V
10010V
47010V
1050V
220016V
100k
100k
10k
10k
13P1.25MMFFC-S
TOTX141
TA7809S TA7809S TA78033LS
NJM3414AV
2SC3624AMUTE SWITCH
2SC3624AMUTE SWITCH
2SC1623
DTA114EKAMUTE SWITCH
DTC114EKAMUTE SWITCH
DTA114EKAMUTE SWITCH
DTC114EKAMUTE SWITCH
DTA114EKAMUTE SWITCH
DTC114EKAMUTE SWITCH
2SB1116CAP MDRIVE
2SB1116A TRIGDRIVE
2SB1116B TRIGDRIVE 2SC3624A
MUTE SWITCH
2SC3624AMUTE SWITCH
DTC114EKAB TRIGDRIVE
DTC114EKACAP MDRIVE
2SC3624AMUTE SWITCH
2SC3624AMUTE SWITCH
2SD2525REG.
10EDB40
10EDB40
10EDB40
1SS3551SS355
DTC114EKAA TRIGDRIVE
1SS355
UDZS-TE-17-4.3B
10EDB40
B-2
B-3
A-M
UTE
B-4
GND
ST A
+9V
AUDI
O A+
4.5V
C32
CDM
D+
3.3V
B-6
CDM
D+
3.3V
B-8
B-9
B-5
B-10
TC D
+3.3
V
-B
EVER
+4V
GND
B-5
3
7
5
2
1
32
19
21
24
22
25
26
FL
FR
23
A8
A7
A6
B7
B8
B9
65
B22
93
56
57
58
59
60
61
28
31
A9
89
A12
90
A11
91
A10
888786
71727476777879
4
94 70
A23
A22
A21 7382838485 A17
A20
A19 95
75
34
33
48
47
40
41
39
42
38
43
37
44
36
45
35
46
DM-R
DM-L
TAPE MECHANISM
DECK
SWITCHING
REGULATOR
DIGITAL OUT
+9V REG +9V REG +3.3V REG
+3.3V REG
DIGITAL OUT
BUFFER
(CHASSIS)
AC IN
HCD-CPX22/NXM3
3434HCD-CPX22/NXM3
7-14. PRINTED WIRING BOARD – PANEL BOARD – • See page 21 for Circuit Boards Location.
R102
0
IC1020
Q102
6R1
037
R103
6
R1034
R1024
R1023
R1021
C102
5
R1025
C1021
C104
8
R102
7R1
028
R103
2R1
029
R103
0R1
031
C102
9
R104
5
R105
1C1052
C1050 R1052
R104
6D1022
Q1024
Q1022
Q1023
R104
1
R1042
R110
2
R110
1
R104
3Q1021 R1100
D1023
R103
3
R103
5R1
040
D102
4
D102
5
D102
6
C1054
R1038
R103
9
R1022
R102
6
C1006
JW1020
JW1022
JW1032
JW1033
JW1034
JW1035
JW1037 JW10
23
JW1021
JW1050
JW10
39
JW10
49
JW1071
JW1043
JW10
40 JW1081
C1053
CN1021
T801
C1051
S1036
S1030
S1032
S1034 +
–
S1035
S1031
S1029 b B
z START
CD
TAPE A/B
CD SYNC
TUNING
ALBUM
DIMMER
DISPLAY
TUNER/BAND
VIDEO(MD)
X
x
CD Z
M>
.m
D1021
S1021
S1022
S1023
S1024
S1028
S1025
S1026
S1027
C102
8
C102
6
JW10
25
JW10
48JW10
24
JW1026
JW1027
FL1020FLOURESCENT INDICATOR TUBE
JW10
36
JW10
45JW
1046
JW1029JW1030
JW1031
1
5 4
1E 3
510
1520
2530
3540
4550
5556
60
JW1038
JW10
47
JW10284849
1716
33 32
64 1
JW10
41
JW10
42
S1033
L1021
LP1001
PANEL BOARD
11(11)1-861-474-
MAIN BOARD(Page30)
E
E
E
E
2 3 4 5 6 7 8 9 10
A
1
B
C
D
E
F
G
Ref. No. Location
D1021 B-1D1022 B-2D1023 B-3D1024 B-2D1025 B-2D1026 B-2
IC1020 B-6
Q1021 B-4Q1022 B-5Q1023 A-5Q1024 A-2Q1026 B-1
• SemiconductorLocation
HCD-CPX22/NXM3
3535HCD-CPX22/NXM3
7-15. SCHEMATIC DIAGRAM – PANEL BOARD –
R1046
R1052C1048
L1021
Q1024SWITCHINGREGULATOR
R1045
C1053
C1050
R1020
C1028
R1039 R1040R1038R1036 R1037
R1034 R1035R1033
R1025C1025
R1023R1022
C1021
R1021
R1024
R1043 R1042 R1041
R1102R1101R1100
C1029
R1027R1026 R1028 R1030R1029 R1031R1032
S1021 S1022 S1023 S1024 S1025 S1026 S1027S1028 S1029 S1030 S1031
S1032 S1033 S1034 S1035 S1036
FL1020
CN1021
R1051
C1051
C1052
C1006C1026
IC1020
Q1024(1/2)
Q1024(2/2)
Q1021 Q1022 Q1023
Q1026
D1022 D1023
D1025
D1024
D1026
D1021
T801
C1054
10k
1000.135V
3.3k
2250V
0.01
100
1050V
10k 33k4.7k1.5k 2.2k
4.7k 10k2.2k
10k220p
100100
0.001
1k
1k
100k 100k 100k
10k10k10k
0.1
330220 470 1k680 1.5k2.2k
13P
10022050V
0.01
0.110
50V
M66005-0131AHPRBOT
CPH5504-TL-E
CPH5504-TL-E
2SC1623 2SC1623 2SC1623
DTC114EKALED SWITCH
RD6.2FM 1SS355
1SS355
1SS355
1SS355
SEL5423
DC-DC CONVERTER
0.0047
36 35
343332313029
2726252423222120
19181716151413121110987654321
50494847464544434241
39 38
28
40
37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 3536
37 51 52
/START(MD)
VIDEODISPLAY TAPE A/BTUNER/BANDCD DIMMER CD SYNC
/KEY CONTROLDISPLAY CONTROL
DRIVEGRID
Q1021-1023
LIQUID CRYSTAL DISPLAY
HCD-CPX22/NXM3
3636HCD-CPX22/NXM3
7-16. PRINTED WIRING BOARD – DISC SW, VOL, HP BOARD – • See page 21 for Circuit Boards Location.
R1049
R1094
C1001R100
1R1
002
Q1001
C1002
R100
3R1
004
R1011
Q1002
R1012
C1003
R1005R1006
Q1003
R1013R1014
C1004R1
007
R100
8
Q1004
C1005
R101
0
R100
9
R1095
C1016
D1051
R1059 Q1041
R1048R1050
R1093
R1092
R1054
R1091R1090
Q1005E
E
E E
E
C1008
C1007
1
10
C1009
JW10
51
JW10
52
JW10
53
JW1002JW1003 JW1004
W1001
NO1001
JW1076
D1001D1002D1003D1005 D1004
CN1051
S1043
D1050
CN1050
S1004S1005DISC 5
VOLUMES1052
TREBLES1051
BASSS1050
DISC 4 DISC 3 DISC 2 DISC 1
S1003 S1002 S1001
JW10
56
JW10
55JW
1054
JW1057
C1013
IC1050 S1042
JW10
58JW
1059JW
1078
JW1073
JW10
69
JW10
77
NO1052
JW10
01
DISC SW BOARD
VOL BOARD
11(11)1-861-475-
11(11)1-861-476-
MAIN BOARD(Page30)
C
MAIN BOARD(Page30)
D
1
10
1 2 3
E
R1088
JR1081
JR1080
C1094
C1093C1096
EP1060
EP1061
CN1062
JW10
97
JW1099
JW10
75
JW10
72
JW10
98JW10
83
JW10
70
MAIN BOARD(Page30)
F
CHASSIS
CHASSIS
J1063PHONES
FB1001
FB10
02
11(11)1-861-477-
HP BOARD
2 3 4 5 6 7 8 9 10 11
A
1
B
C
D
E
F
G
Ref. No. Location
D1001 C-6D1002 C-5D1003 C-4D1004 C-4D1005 C-3D1050 E-6D1051 E-5
IC1050 E-5
Q1001 B-6Q1002 C-5Q1003 C-4Q1004 C-3Q1005 C-2Q1041 E-6
• SemiconductorLocation
HCD-CPX22/NXM3
3737HCD-CPX22/NXM3
7-17. SCHEMATIC DIAGRAM – DISC SW, VOL, HP BOARD –
R1004 R1008R1006 R1010R1002
R1009R1007
R1005R1003
R1001
R1012R1011 R1013 R1014 C1009
R1049
R1050
C1013
R1059 R1090R1091
R1092
R1093
R1094 R1095
R1048
R1088
JR1080
C1093
C1094
FB1001FB1002
C1008
S1050 S1051 S1052S1042
CN1051
CN1050
S1043
JW1099
JR1081
JW1098
C1007
NO1052
NO1001
J1063
S1001 S1002 S1003 S1004 S1005
IC1050
Q1001 Q1002 Q1003 Q1004 Q1005
D1005D1004D1003D1002D1001
Q1041
D1050
D1051
CN1062
C1096
EP1061
680 680680 680680
680680
680680
680
330220 470 680 0.1
1k
220
4716V
47 1k1k
1k
1k
1k 1k
2.2k
0
0
0.001
0.001
0.1
5P
15P
0
0.1
10P
10P
NJM74M400A
DTC114EKALED DRIVE
DTC114EKALED DRIVE
DTC114EKALED DRIVE
DTC114EKALED DRIVE
DTC114EKALED DRIVE
SEL5823ASEL5823ASEL5823ASEL5823ASEL5823A
DTC114EKA
SEL5223S
1SS355
4P
1000p1 2 3 4 5 5
4321
7
1234
56
7
89
101112
89101112
1234 56I/
(CHASSIS)
(CHASSIS)
REMOTECONTROLRECEIVER
SWITCH
Q1001-1005LED
SWITCHLED
HCD-CPX22/NXM3
3838HCD-CPX22/NXM3
7-18. PRINTED WIRING BOARD – S-MASTER BOARD – • See page 21 for Circuit Boards Location.
C710
C757
C807
R713
R752
C794
C734
IC706R7
23
R766
R716
IC703
R773
L710
IC701C732
L711
L760
Q702
C717
C718C713
C715
R754
C758
L761
C764
C778
C716
FL703R7
56
Q701
R757
Q753
C767
C768C763
C765
R76412
3 1
4 5
1
34
8
3
321
3 14 5
C714
C726
R759
R758
R731
R732
R704
R706
C709R714
C708
R707
R708
R709
FB70
2R783FL706
R781
R782C7
85
X702
IC709R779
L703
IC705
IC710
X701
R784R785
R786
R787
R788
R789
R790R735
R739
R741
R743
R742
C766
FL702 L701
R729
C733
FL704
C759
C806
IC70
7
IC70
8
R719
R720
R769
R770
R730
R793
R792
C737
LP701
C704
S-MASTER BOARD (SIDE A)
SP OUT BOARD
S-MASTER BOARD (SIDE B)
11(11)1-861-480-
11(11)1-861-480-
11(11)1-861-479-
R721 R718R771
Q703
R768
C775
C829
C822
CHASSIS
C821 C824
C830
C825C826
C827
C828
R761
D710
C801
R744
L712
R762
C722
C727
D705
D706
C805
R772
C723
C712
C721
R728
C706
R717
C724
L714
C772
R776
R726
R778 R777
C776
L716
D755
D756
R727
C773
C762
Q752
E
C771
C756
C725
R767
C774
R722
C788
C752
R710 R7
11R7
12
C781 C7
82
C750
C786
C784
C783
L705C799
C779C780 L715
R751
R701
R737
R736C739C738
D711D712
C802
R795
R745
R746
R748
C787
R747
C745R749
C746
IC70
4
R750
C797
L702
D707
D708
C800
D702
D701
C749
D709
C729
D703
D704
C795
C823
C754
R760
L713
R724
R725 R7
74
R775
L704
C730
C790C741
C798
C753
C700C747
C731
C751
C701
CN70
0
L708
L709
L758
L759
C803
C804
CN70
1C777C770
C769
C791
C792
C719
C728C720
C702
CN702
EP701 EP702
C736C735C748
C703
MAIN BOARD(Page30)
G
MAIN BOARD(Page30)
H
CHASSIS
CHASSIS CHASSIS
C594C598
C599C592
C595C596C597
L
SPEAKER
R
C591
L590 L591
R597R596
CN510
R598
TM504
L592 L593AEP,UK,EA,RU
AEP,UK,EA,RU
AEP,UK,EA,RU
EXCEPT AEP,UK,EA,RU
R599
EP504
R592R593R594R595
JW593JW592JW590JW591
EP505
LP591LP592
EE
E
E SWITCHINGREGURATOR
(Page30)
I
2 3 4 5 6 7 8 9 10 11 12
A
1
B
C
D
E
F
Ref. No. Location
D701 A-5D702 B-5D703 B-5D704 A-5D705 C-5D706 C-6D707 A-5D708 A-5D709 B-5D710 B-5D711 C-5D712 C-5D755 C-6D756 C-7
• SemiconductorLocation
Ref. No. Location
IC701 A-3IC703 A-2IC704 A-6IC705 B-2IC706 B-1IC707 C-3IC708 C-1IC709 B-2IC710 D-1
Q701 E-2Q702 E-3Q703 E-5Q752 E-7Q753 E-1
HCD-CPX22/NXM3
3939HCD-CPX22/NXM3
7-19. SCHEMATIC DIAGRAM – S-MASTER BOARD –
X701
R735
C739
R736R737
C738
R732
R731
C737
C736
L703
FL703 R739
L702
IC703
D711
D712
C802C735
C734
IC701
R746
R745
C733
R730
C729 C795
C732
R729
C731
D702
D701
L701
C749
C748
C730
L713
IC704
C797
C747
C746
R749
C745
R747 R748
R744
C806
R743R741
R742
R790
C788 C787C703
R784
R785
R786
R788
R787
R789
IC705
C704
C754
C753
L716
C825
C826
C780C799
C779
C700
L714
R779
R750
C798FL704C750
IC706
L712
C805
C790
C783
L705
X702
C785
R781R782
C784
R783FB702
C741
C786
FL706
IC709
L715
L704
CN510
TM504
JW593
R599
L593
L592R598
JW592
JW590
R597L591
R596 L590
JW591
EP505
EP504C598 C594 R592
C592 C599 R593
R594C595C596
C597 C591R595
D703
D704
C752
FL702
R795
C701
R701R751
C751
D710
D709
C801
CN700
CN701
C821 C822EP701
R723
R716
R704
IC707
R706
C709
C781R707C708
R708R709
R711
R712
R714
C710
R710
R713
C712
R717
C702
L708
C714 C715
D706
D705 L709
C716 C717C718
C706R722
R720 C719
C713
R719
C830
C829
L710
C720
R721
C721 C722
C723
R725
C725C727
R718C728
L711
C724
R724
C792
C828
C827Q702
Q703
R778
R726
R728
R727C726
R777
R776
C778
Q753Q752
Q701R792
C794
C770
C777R768
R771 C771
C776
L761
C772
C773R774
R775
C774
C775
R766 R773
C763
R767
L758
C764 C765 R769
D756
D755 L759
C768 C766 C767R770
L760
C756
R772
C769
C791IC708
R761
R764 R762
C759R760
R759
R754
C758
R752 C757
C782
R757
R758
R756
C823 C824
EP702
C762
CN702
R793
IC710
C803C804C800
D707D708
12.288M
0
10p
1M1k
10p
100
100
0.1
4.750V
0UH 0TC7WU04F-TE12L
1SS355TE-17
1SS355TE-17
0.110
50V
0.1
PCM1802DBR
100
100
0.1
100
0.1 0.1
0.1
1k
10010V
1SS355TE-17
1SS355TE-17
0.1
1050V
0.1
0
NJM2870F18
0.01
10010V
0.1
0
0.1
100 47k
0
0.1
100100
10k
100
0.1 0.110010V
100
100
100
100
100
100
CXD9788AR
0.1
0.1
10010V
0
0
0
0.10.1
0.1
10010V
0
0
100k
10010V
0UH0.01
0.1
10010V
10p
49.152M
5p
1001M
0.001
00
2250V
0.01
0UH
MC74VHC1GU04
0
0
4PEH-S
2P
101/2W
101/2W
101/2W
101/2W
100000p 100000p 101/2W
100000p 100000p 101/2W
101/2W100000p100000p
100000p 100000p10
1/2W
1SS355TE-17
1SS355TE-17
0.1
0UH
0
150V
00
150V
1SS355TE-17
1SS355TE-17
0.1
19PFFC-S
8PEH-S
0 0
47k1/10W
4.7k1/10W
0
CXD9775M
100
0.1
0.101
00
100
100
560
47p
100
22k
1
0
0.1
0
0.22 0.22
P6SMB39AT3
P6SMB39AT3 0
0.22 0.220.033
10
3.31/4W
220035V
0.033
3.3 1/4W
0
0
1
4.7k1/10W
0.22 0.0022
0.0022
2.71/10W
0.00220.22
4.7k1/10W
1 0.0022
2.71/10W
47016V
0
02SA1602
PNP2SA1602
PNP 100k
100k
100k
100k2.2
100k
100k
2.2
2SA1602PNP
2SA1602PNP
2SC1623PROTECT
0
1
1
14.7k
1/10W
4.7k1/10W 0.22
0.22
0.0022
0.00222.7
1/10W
2.71/10W
0.0022
0.0022
4.7k1/10W
47k1/10W
0.033
0
0
0.22 0.22 3.31/4W
P6SMB39AT3
P6SMB39AT3 0
0.033 0.22 0.223.3
1/4W
1
0
220035V
0.1CXD9775M
100
0 100
0.1100
0
560
1
22k 47p
0.1
0
0
100
0 01
4PEH-S
100k
0.150V100
10V0.1
1SS355TE-171SS355TE-17
PDW
N
/RST
/SD
/OTWPD
WN
/RST
INIT
SCLA
TCH
SCSH
IFT
SCDT
PGM
UTE
SOFT
MUT
ENS
PMUT
EOV
F/O
TW/S
DNS
PMUT
ESO
FTM
UTE
PGM
UTE
SCDT
SCSH
IFT
SCLA
TCH
INIT
OVF
R
L
SPEAKER
(CHASSIS)
(CHASSIS)
(CHASSIS)
(CHASSIS)
A/D CONVERTER
BUFFER
+1.8V REGULATOR
REGULATORD+3.3V
A+5V REGULATOR
DIGITAL POWER AMP
DIGITAL POWER AMP
DATA CONVERTER
CLOCK GEN
DETECTOVER LOAD
Q702,703,752,753
EXCEPT
EXCEPT
EXCEPT
EXCEPT
AEP,UK,EA,RU
AEP,UK,EA,RU
AEP,UK,EA,RU
AEP,UK,EA,RU
AEP,UK,EA,RU
AEP,UK,EA,RU
AEP,UK,EA,RU
AEP,UK,EA,RU
HCD-CPX22/NXM3
4040HCD-CPX22/NXM3
7-20. IC Block Diagram
– BD Board –
IC251 BA5947FM
– RELAY Board –
IC701, 711 BA6956AN
15
16
17
1819
20
21
22
23
24
25
26
27
36
28
29
30
31
32
33
34
35
1
2
3
4
5
6
7
8
9
10
11
12
13
14
LEVELSHIFT
FR
R
F
RF
F
19k
6.5k
50k 50k
100k
50k
PIN310k
Vref
50k 50k
PIN26
(ch1, 2)
POWVCC
(ch3, 4)
SW
PreVcc
INTERFACE
INTERFACE
INTERFACE
R
F
50k 50k
POWVCC
MUT
E
Vref
POWVCC
RF
10k
CH1PUTF
CH1OUTR
CH2OUTF
CH2OUTR
POWVCC
CNF4
GND
C-M
C-P
VG
CH2RIN
CH2FIN
CH1RIN
CH1FIN
SW
OPIN+
OPIN-
NC
CH4OUTR
CH4OUTF
CH3OUTF
CH3OUTR
POWVCC
MUTE
GND
GND
PREGND
CT
CH3RIN
CH3FIN
CH4IN
CH4CAPA
OUTVREF
DPOUT
TREVCC
NC
D
D
D
D
D
D
D
D
1 2 3 4 5 6 7 8 9
CONTROL LOGIC
TSD
VREF
OUT2
OUT1
RNF
VM VCC
FIN
GND
RIN
– BD Board –
IC301 TC94A34FG-002
33
34
35
36
37
38
39
40
41
42
1
8
43
61 62 63 646059565250
47
46
45
44
48
49
2526272829303132 1718192021222324
9
10
11
2
3
4
5
6
7
5857555351
12
13
14
15
16
54
CS/RAS/ADO2
AD15/CAS/PD12
SDO3/OE
WE
/SD
O1
PIO
7/B
US
3/IO
7
PIO
6/F
I3/B
US
2/IO
7
PIO
5/F
I2/B
US
1/IO
5
PIO
4/F
I1/B
US
0/IO
4
BusSwitch
PO11/BUCK/AD14
PO10/CCE/AD13
PO9/AD12
PO08/AD11
Gen
eral
In/O
utpu
t Por
t
Add
ress
Cal
c.2s
ets
Y-P
oint
erre
gist
erC
-Poi
nter
regi
ster
X-P
oint
erre
gist
er
VDDM
SRMSTB
VDDT
AD10
AD9
ER
AM
2k w
ord
CR
AM
4k w
ord
CR
OM
4k w
ord
YR
AM
4k w
ord
XR
AM
4k w
ord
SR
AM
/D
RA
M I/
F
SR
AM
I/F
1Mbi
tS
RA
MX
-Bus
Y-B
us
PO07/AD7
PO06/AD6
PO05/AD5
AD8
VC0Timing
Generator
PR
AM
Inst
ruct
ion
Dec
oder
Pro
gram
Con
trol
MC
U. I
/F
regi
ster
XO
• X
1 •
X2
Y0
• Y1
• Y2
MX
MY
MZ
MA
C
A0
A1
AX
AY
ALU
A2
A3
DIT
roun
d &
lim
itro
und
& li
mit
Aud
io I/
F
LRCKIA
BCKIA
SDI0
LRCKO
BCKO
SDO0
VSS
VDDT
MIACK
MICK
MIDIO
MILP
MICS
STANBY
RESET
VDDPA
D4/
PO
04
AD
3/P
O03
AD
2/P
O02
AD
1/P
O01
AD
0/P
O00
VS
S
VD
D
CK
O/P
O13
/AD
16
VD
DX
XO
TE
ST
VC
OI
VS
SXXI
MIM
D
VS
SP
PIO
3/IO
3
PIO
2/IO
2
PIO
1/S
DI3
/IO1
PIO
0/S
DI2
/IO0
VS
S
CK
I/CLO
CK
/IRQ
/FIO
VD
D
TX
O
SF
SY
/LR
CK
IB
SB
SY
/BC
KIB
SD
I1/D
ATA
PO
M
Sub
cod
eI/F
CD
P C
ont
I/F
41
HCD-CPX22/NXM3
7-21. IC Pin Function Descriptions• IC101 CXD3059AR (RF AMP) (BD BOARD)
Pin No. Pin Name I/O Description
1 MIRR I/O Mirror signal input/output(Not used)
2 DFCT I/O Defect signal input/output (Not used)
3 FOK I/O Focus OK signal input/output (Not used)
4 VSS — Internal digital ground
5 LOCK I/O Not used
6 MDP O Spindle motor servo control output
7 SSTP I Disk innermost detection signal input
8 IOVSS1 — I/O digital ground
9 SFDR O Sled drive output
10 SFDR O Sled drive output
11 TFDR O Tracking drive output
12 TRDR O Tracking drive output
13 FFDR O Focus drive output
14 FFDR O Focus drive output
15 IOVDD1 — I/O digital power supply
16 AVDD0 — Analog power supply
17 AVSS0 — Analog ground
18 NC — Not used
19 E I E signal input
20 F I F signal input
21 TEI I Tracking error signal input
22 TEO O Tracking error signal output
23 FEI I Focus error signal input
24 FEO O Focus error signal output
25 VC I/O Center voltage output from RF amplifier block
26 A I A signal input
27 B I B signal input
28 C I C signal input
29 D I D signal input A
30 NC — Not used
31 AVDD4 — Analog power supply
32 RFDCO O RFDC signal output (Not used)
33 PDSENS I Reference voltage pin
34 AC_SUM O RFAC summing amplifier output
35 EQ_IN I Equalizer circuit input
36 LD O APC output
37 PD I APC input
38 NC — Not used
39 RFC I Equalizer cut-off frequency adjustment pin
40 AVSS4 — Analog ground
41 RFACO O RFAC signal output
42 RFACI I RFAC signal input or EFM signal input
43 AVDD3 — Analog power supply
44 BIAS I Asymmetry circuit constant current input
45 ASYI I Asymmetry comparator voltage input
46 ASYO O EFM full-swing output
47 VPCO O Not used
48 VCTL I Wide-band EFM PLL VCO2 control voltage input
42
HCD-CPX22/NXM3
Pin No. Pin Name I/O Description
49 AVSS3 — Analog ground
50 CLTV I Multiplier VCO1 control voltage input
51 FILO O Master PLL (slave = digital PLL) filter output
52 FILI I Master PLL filter input
53 PCO O Master PLL charge pump output
54 AVDD5 — Analog power supply
55 DDVROUT O DC/DC converter output
56 DDVRSEN I DC/DC converter output voltage monitor input
57 AVSS5 — Analog ground
58 DDCR I DC/DC converter reset input
59 NC — Not used
60 BCKI I D/A interface bit clock input
61 PCMDI I D/A interface serial data input (2’s COMP, MSB first)
62 LRCKl I D/A interface LR clock input
63 LRCK O D/A interface LR clock output f = Fs
64 VSS — Internal digital ground
65 PCMD O D/A interface serial data output (2’s COMP, MSB first)
66 BCK O D/A interface bit clock output
67 VDD — Internal digital power supply
68 EMPH O High when the playback disc has emphasis, low it has not
69 EMPHI I High when de-emphasis is ON, low when input OFF
70 IOVDD2 — I/O digital power supply
71 DOUT O Digital Out output
72 TEST I Test pin Normally ground
73 TES1 I Test pin Normally ground
74 IOVss2 — I/O digital ground
75 NC — Not used
76 XVSS — Master clock ground
77 XTAO O Crystal oscillation circuit output
78 XTAI I Crystal oscillation circuit input
79 XVDD — Master clock power supply
80 AVDD1 — Analog power supply
81 AOUT1 O Lch analog output
82 VREFL O Lch reference voltage
83 AVSS1 — Analog ground
84 AVSS2 — Analog ground
85 VREFR O Rch reference voltage
86 AOUT2 O Rch analog output
87 AVDD2 — Analog power supply
88 NC — Not used
89 IOVDD0 — I/O digital power supply
90 RMUT O Rch “0” detection flag (Not used)
91 LMUT O Lch “0” detection flag (Not used)
92 NC — Not used
93 XTSL I Crystal selection input (Not used)
94 IOVSS0 — I/O digital ground
95 XTACN IOscillation circuit control
Self-oscillation when high, oscillation stop when low
96 SQSO O Subcode Q 80-bit and PCM peak and level data output (Not used)
97 SQCK I SQSO readout clock input
43
HCD-CPX22/NXM3
Pin No. Pin Name I/O Description
98 SBSO O Subcode P to W serial output (Not used)
99 EXCK I SBSO readout clock input (Not used)
100 XRST I System reset input
101 SYSM I Mute input
102 D ATA I Serial data input from CPU
103 VSS — Internal digital ground
104 XLAT I Latch input from CPU
105 CLOCK I Serial data transfer clock input from CPU
106 VDD — Sled drive output Internal digital power supply Tracking drive output
107 SENS O SENS output to CPU
108 SCLK I SENS serial data readout clock input
109 ATSK I/O Anti-shock input/output (Not used)
110 WFCK O WFCK output (Not used)
111 XUGF O XUGF output (Not used)
112 XPCK O XPCK output (Not used)
113 GFS O GFS output (Not used)
114 C2PO O C2PO output (Not used)
115 SCOR O High output when the subcode sync, S0 or S1, is detected
116 VDD — Internal digital power supply
117 C4M O 4 2336MHz output (Not used)
118 WDCK O Word clock output f = 2Fs (Not used)
119 COUT I/O Track number count signal input/output (Not used)
120 NC — Not used
44
HCD-CPX22/NXM3
• IC401 M30622MGN-B28FPUO (SYSTEM CONTROL) (MAIN Board)
Pin No. Pin Name I/O Description
1 MP3 CS O Chip select signal to CD Digital Processor
2 MP3 LP O Latch pulse output to CD Digital Processor and Motor signal output
3 MP3 ACK I ACK input from CD Digital Processor and Motor signal input
4 SIRCS I Remote commander signal input
5 MP3 DATA OUT O Serial data output to the MP3 circuit
6 MP3 DATA IN I Serial data input from the MP3 circuit
7 MP3 CLK O Serial clock output to the MP3 circuit
8 BYTE I External data bus width select input (connected to ground)
9 CN VSS I Processor modes switch
10 Xcin I Sub clock input (32.768kHz)
11 Xcout O Sub clock output (32.768kHz)
12 RESET I System reset input
13 Xout O Main system clock output (16MHz)
14 Vss – Ground
15 Xin I Main system clock input (16MHz)
16 Vcc – Power supply
17 NMI I Non-maskable interrupt input
18 RDS-INT I Sirial data taransfer clock signal input
19 SCOR I CD Q-DATA request
20 AC-CUT I AC cut-off detection signal input
21 SENS I Internal status(SENSE) signal input from CXD3059AR
22 CD-DATA O Serial data output
23 CD-CLK O Serial data transfer clock signal output
24 XLT O Serial data latch pulse output
25 XRST O Reset signal output to the CD mechanism
26 XCTN O XCTN signal output (for Tuner noise reduction)
27 A-MUTE O Audio muting on/off control signal output
28 MP3-STANDBY O Standby signal output to the MP3 circuit
29 IIC_CLK I/O Communication data reading clock signal input or transfer clock siganal output
30 IIC_DATA I/O Communication data bus with CD mechanism and Fluorescent indicater
31 MP3 REQ I REQ signal input from MP3 circuit
32 MP3 RESET O RESET signal output to the MP3 circuit
33 CDM-MOT-POS-1 O Motor drive signal output (L/D)
34 CDM-MOT-POS-2 O Motor drive signal output (U/D)
35 CDM-MAIN-SW-CLS I Detection signal input from disc tray close detect main switch
36 CDM-SUB-SW-OPN I Detection signal input from disc tray open detect sub switch
37 CDM-ENC-A-1 I Detection signal input from the disc tray address detect rotary encoder
38 CDM-ENC-A-3 I Detection signal input from the disc tray address detect rotary encoder
39 CDM-ENC-B-1 I Detection signal input from the disc tray address detect rotary encoder
40 CDM-ENC-B-3 I Detection signal input from the disc tray address detect rotary encoder
41 CDM-ENC-B-2 I Detection signal input from the disc tray address detect rotary encoder
42 CDM-ENC-B-0 I Detection signal input from the disc tray address detect rotary encoder
43 CDM-ENC-A-2 I Detection signal input from the disc tray address detect rotary encoder
44 CDM-ENC-A-0 I Detection signal input from the disc tray address detect rotary encoder
45 CDM-SUB-SW-CLS I Detection signal input from disc tray close detect sub switch
46 CDM-MAIN-SW-OPN I Detection signal input from disc tray open detect main switch
47 CDM-MOT-NEG-2 O Motor drive signal output (U/D)
48 CDM-MOT-NEG-1 O Motor drive signal output (L/D)
49 RDS-DATA I RDS data input
50 ST-MUTE O Tuner muting control signal output to tuner unit
45
HCD-CPX22/NXM3
Pin No. Pin Name I/O Description
51 TUNED IN I Tuning detecton signal input from tuner unit
52 ST-CE O PLL chip enable signal output to tuner unit
53 ST-DOUT O PLL serial data output to tuner unit
54 ST-DIN I PLL serial data input from tuner unit
55 ST-CLK O PLL serial tansfer clock signal output to tuner unit
56 SM-DATA O Serial data output to the S-Master circuit
57 SM-CLK O Serial data transfer outout to the S-Master circuit
58 SM-LAT O Serial data latch pulse output to the S-Master circuit
59 SM-INT O Initial signal output to the S-Master (Power reset)
60 SM-ENB O ENABLE signal output to the S-Master
61 SM-ADC-POWR O ADC signal to the S-Master
62 VCC – Power supply
63 TC-REC-MUTE O Recording muting on/off selection signal output
64 VSS – Ground
65 STBY-RELAY O Main power on/off control signal output
66 IO-EXP:CLK O Serial data transfer output to the I/O expander circuit
67 IO-EXP:LAT O Serial data latch pulse output to the I/O expander circuit
68 IO-EXP DATA IN I Serial data input from the I/O expander circuit
69 IO-EXP DATA OUT O Serial data output to the I/O expander circuit
70 VOL-A I Jog dial pulse input from the rotary encoder (Volume)
71 VOL-B I Jog dial pulse input from the rotary encoder (Volume)
72 LED:STANDBY O Standby signal output to the LED driver
73 DISPLAY KEY I Display key input signal
74 POWER KEY I Power key input signal
75 DISC-SENS I Disc status detection signal input
76 JOG 1-A I Jog dial pulse input from the rotary encoder (Bass)
77 JOG 1-B I Jog dial pulse input from the rotary encoder (Bass)
78 JOG 2-A I Jog dial pulse input from the rotary encoder (Treble)
79 JOG 2-B I Jog dial pulse input from the rotary encoder (Treble)
80 AMP-DATA O Serial data output to the Front Amp circuit
81 AMP-CLK O Serial clock output to the Front Amp circuit
82 FL-RESET O Reset signal output to the FL indicator tubu circuit
83 FL-CS O Chip select signal output to the FL indicator tubu circuit
84 FL-CLK O Serial clock output to the FL indicator tubu circuit
85 FL-DATA O Serial data output to the FL indicator tubu circuit
86 CAMP-CNT1 O Capstan motor drive signal output
87 A TRG O Deck-A side trigger plunger drive signal output
88 B TRG O Deck-B side trigger plunger drive signal output
89 A SHUT I Shut off detection signal input from the deck-A side reel pulse detector
90 B SHUT I Shut off detection signal input from the deck-B side reel pulse detector
91 B HALF I Detection input from the deck-B half detect switch
92 SPEC-IN I Setting terminal for the version
93 MAIN-TRANS-CUT I Main transformer cut detect signal input
94 AD-KEY 2 I AD key 2 signal input
95 AD-KEY 1 I AD key 1 signal input
96 AVSS – Ground
97 VACS IN I VACS signal input
98 VREF I Reference voltage input
99 AVCC – Analog power supply
100 AMS-IN I Automatic music senser signal input
46
HCD-CPX22/NXM3
Pin No. Pin Name I/O Description
1 XVss – Ground
2 Vsubc – Ground
3 VssR – Ground
4 OUTR2 O PWM2 output for R-ch power stage.
5 VddR – Power supply(+3.3v)
6 OUTR1 O PWM1 output for R-ch power stage.
7 VssR – Ground
8 VssL – Ground
9 OUTL2 O PWM2 output for L-ch power stage.
10 VddL – Power supply(+3.3v)
11 OUTL1 O PWM1 output for R-ch power stage.
12 VssL – Ground
13 XOVss – Ground
14 XfsoOUT O Secondary master clock buffer output
15 XOVdd – Power supply(+3.3v)
16 DVdd – Power supply(power supply for digital section +1.8v)
17 DVss – Ground
18 NSPMUTEI I PWM duty50% mute and delta/sigma registor clear signal input
19 SoftMUTE I Soft mute signal input
20 PGMUTE I Mute signal input for PWM output data
21 SCDT I Serial control data input
22 SCSHIFT I Serial control shift clock input
23 SCLATCH I Serial control latch signal input
24 OVFFLAG O R-ch arithmetic section overflow detect flag output
25 OVFFLAG O L-ch arithmetic section overflow detect flag output
26 SFLAG O Anti-synchronize detect flag output
27 INIT I Initalise signal input (power reset)
28 MCKSEL I Secondary master clock select input
29 LRCK I Sampling clock input (correspond to CD/MD/DVDaudio etc)
30 BCK I Bit clock input(correspond to CD/MD/DVDaudio etc)
31 DATA I Audio data input(correspond to CD/MD/DVDaudio etc)
32 BFVdd – Power supply(+3.3v)
33 BFVss – Ground
34 TEST I Test terminal(normaly ground)
35 DVdd – Power supply(power supply for digital section +1.8v)
36 XFfsilN I Primary master clock input
37 FsoCKO O Secondary fso clock M-output
38 Fsol I Secondary fso clock input
39 HPOUTR2 O Not used
40 HPVssR – Ground
41 HPOUTR1 O Not used
42 HPVddR – Power supply(+3.3v)
43 HPOUTL2 O Not used
44 HPVddL – Ground
45 HPOUT O Not used
46 HPVddL – Power supply(+3.3v)
47 XVdd – Power supply(+3.3v)
48 XfsoIN I Secondary master clock input(1024/512fso)
• IC705 CXD9788AR (DATA CONTOL) (S-MASTER Board)
47
HCD-CPX22/NXM3
Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks
SECTION 8EXPLODED VIEWS
8-1. MAIN SECTION
NOTE:• -XX, -X mean standardized parts, so they may
have some differences from the original one.• Items marked “*” are not stocked since they
are seldom required for routine service. Somedelay should be anticipated when ordering theseitems.
• The mechanical parts with no reference numberin the exploded views are not supplied.
• AbbreviationE3 : 240V AC Area in E modelE51 : Chilean and Peruvian modelEA : Saudi Arabia modelRU : Russian model
The components identified by mark 0 ordotted line with mark 0 are critical forsafety.Replace only with part number specified.
#1
#1
#1
#1
#1
not supplied
1
3 4
1414
5
12
6
13
7
7
7
7
8
8
9
10
11
8
8
#1
#1
1 A-1052-039-A MAIN BOARD, COMPLETE (EA)1 A-4750-856-A MAIN BOARD, COMPLETE (AEP, UK)1 A-4750-931-A MAIN BOARD, COMPLETE (RU)1 A-4750-933-A MAIN BOARD, COMPLETE (E3)1 A-4750-935-A MAIN BOARD, COMPLETE (E51)
1 A-4750-937-A MAIN BOARD, COMPLETE (US)3 1-769-984-11 WIRE (FLAT TYPE) (13 CORE)4 1-765-332-11 WIRE (FLAT TYPE) (15 CORE)5 1-769-869-11 WIRE (FLAT TYPE) (5 CORE)6 1-769-939-11 WIRE (FLAT TYPE) (11 CORE) (EXCEPT AEP, UK)
6 1-773-003-11 WIRE (FLAT TYPE) (15 CORE) (AEP, UK)7 3-363-099-22 SCREW (CASE 3 TP2)
8 4-951-620-01 SCREW (2.6X8), +BVTP9 4-252-541-51 CASE10 4-252-538-01 PANEL, TOP
11 1-693-603-31 TUNER (FM/AM) (E3, E51, EA)11 1-693-604-11 TUNER (FM/AM) (AEP, UK)11 1-693-623-31 TUNER (FM/AM) (US)11 1-693-654-11 TUNER (FM/AM) (RU)12 1-773-119-11 WIRE (FLAT TYPE) (19CORE)
13 1-827-488-11 WIRE (FLAT TYPE) (27CORE)14 1-500-386-11 FILTER, CLAMP (FERRITE CORE)#1 7-685-646-79 SCREW +BVTP 3X8 TYPE2 IT-3#2 7-685-647-79 SCREW +BVTP 3X10 TYPE2 TT (B)
48
HCD-CPX22/NXM3
8-2. FRONT PANEL SECTION
Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks
not suppliednot supplied
not supplied
not supplied
#1
not supplied
not supplied
notsupplied
not supplied
51
52
53
57
57
56
57 57
57
57
57
57
57
57
58
5757
57
59
60
61
57
57
55
55
6263
51 4-252-535-11 KNOB (VOL)52 4-252-536-11 KNOB (B/T)53 X-4956-194-1 PANEL ASSY (U) (CPX22), FRONT (US)53 X-4956-200-1 PANEL ASSY (CPX22), FRONT (AEP, UK)53 X-4956-262-1 PANEL ASSY, FRONT (E3, E51, EA)
53 X-4956-333-1 PANEL ASSY, FRONT (RU)55 3-970-608-01 SUMITITE (B3), +BV56 A-4750-851-A VOL BOARD, COMPLETE57 4-951-620-01 SCREW (2.6X8), +BVTP
58 A-4750-849-A FL COM BOARD, COMPLETE
59 1-796-880-11 DECK, MECHANISM60 X-4956-197-1 HOLDER (A) (TC) ASSY61 X-4956-198-1 HOLDER (B) (TC) ASSY62 4-252-530-01 SPRING (HB)63 4-252-529-01 SPRING (HA)
#1 7-685-646-79 SCREW +BVTP 3X8 TYPE2 IT-3
49
HCD-CPX22/NXM3
8-3. CHASSIS SECTION
Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks
#1
#1
#1
#1
#1
#1
#1
#1
#1
#1
#1
not supplied
not supplied
not supplied
CDM81B-F1BD81A
not supplied
101
102
103
104
106
105107
The components identified bymark 0 or dotted line with mark0 are critical for safety.Replace only with part numberspecified.
101 A-4750-863-A S-MASTER (A) BOARD, COMPLETE0102 1-468-813-11 REGULATOR, SWITCHING (AEP, UK, RU)0102 1-468-819-11 REGULATOR, SWITCHING (US)0102 1-468-821-11 REGULATOR, SWITCHING (E3, E51, EA)0103 1-775-786-21 CORD, POWER (UK, EA)
0103 1-777-071-53 CORD, POWER (AEP, E51, RU)0103 1-783-820-11 CORD, POWER (US)
0103 1-827-226-11 CORD, POWER (E3)* 104 3-703-244-00 BUSHING (2104), CORD (EXCEPT E3)
104 3-703-571-11 BUSHING (S) (4516), CORD (E3)
105 1-500-497-11 FILTER, CLAMP (FERRITE CORE)106 1-469-854-11 CORE, FERRITE (US)107 1-500-386-11 FILTER, CLAMP (FERRITE CORE) (US)#1 7-685-646-79 SCREW +BVTP 3X8 TYPE2 IT-3
50
HCD-CPX22/NXM3
8-4. CD MECHANISM DECK SECTION-1(CDM81B-F1BD81A)
Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks
#5
#3
#3
#5
#5
#3
#3
153154
151
152
155
156
157
158
159
160
161
162
163
164
165
166
167
151 4-251-849-01 LEVER (SW2)152 4-251-991-01 SPRING (SW2), TORSION153 4-251-860-01 LEVER (LOCK)154 4-251-867-01 SPRING (LOCK), TORSION155 4-251-828-01 TRAY (MAIN)
156 4-252-533-11 PANEL, LOADING157 4-251-857-01 COVER (R)158 4-251-830-01 SLIDER (ST)159 4-251-858-01 COVER (L)160 4-251-829-01 TRAY (SUB)
161 X-4955-707-2 PULLEY (A5) ASSY, CHUCKING (CPX22)161 X-4955-707-3 PULLEY (A5) ASSY, CHUCKING (NXM3)162 1-471-035-11 MAGNET ASSY163 4-251-821-01 BRACKET (TOP)164 4-231-189-01 PULLEY (B), CHUCKING
165 4-251-824-01 LIFTER166 4-985-672-01 SCREW (+PTPWHM2.6), FLOATING167 4-251-822-01 JOINT (LIFTER)#3 7-685-534-19 SCREW +BTP 2.6X8 TYPE2 N-S#5 7-685-102-19 SCREW +P 2X4 NON-SLIT TYPE 2
51
HCD-CPX22/NXM3
8-5. CD MECHANISM DECK SECTION-2(CDM81B-F1BD81A)
Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks
#4 #4
#4
#3
#3
#3
S771
not supplied
not supplied
#4#4
#4
#4
#3
not supplied
M761
M762
#4
#4
#4
#4#4
#4
201
208
208
208
211212
213
203203
203
204
209 214 214
210
215
205
206
207
202
201 4-251-870-01 BELT (BU)202 4-251-869-01 BELT (MAIN TRAY)203 4-251-841-01 GEAR (SUB TRAY 1)204 4-251-873-01 SPRING (MODE), COMPRESSION205 4-239-618-02 SCREW (+PWH, 2X6), STEP TAPPING
206 4-251-872-01 SPRING (LEVER), TORSION207 4-251-868-01 BELT (SUB TRAY)208 4-251-853-01 PULLEY (BU)209 4-251-834-01 LEVER (MAIN TRAY)210 4-251-852-01 GEAR (MAIN TRAY 3)
211 4-251-854-01 GEAR (BU1)212 4-251-850-01 GEAR (MAIN TRAY 1)213 4-251-856-01 GEAR (BU2)214 4-251-842-01 GEAR (SUB TRAY 2)215 4-251-851-01 GEAR (MAIN TRAY 2)
M761 A-4713-174-A MOTOR (81) ASSY (LD/ST MOTOR)M762 A-4713-174-A MOTOR (81) ASSY (BU U/D MOTOR)S771 1-478-552-11 ENCODER, ROTARY#3 7-685-534-19 SCREW +BTP 2.6X8 TYPE2 N-S#4 7-685-902-21 SCREW +PTPWH 2.6X8 (TYPE2)
52
HCD-CPX22/NXM3
8-6. CD MECHANISM DECK SECTION-3(CDM81B-F1BD81A)
not supplied
not supplied
not supplied
BU-F1BD81A
not supplied
#3#4
#4#4
#4 #3
#3
S781
#4
#4#4
#4#4
#3
#3
#4
251
251
252
256
257
273
272
270
259
255271
260254272269
268
258
253
251
261
262
262 263263
263
262
264
265
266
267
252
Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks
251 4-985-672-01 SCREW (+PTPWHM2.6), FLOATING252 4-251-873-01 SPRING (MODE), COMPRESSION253 4-251-874-01 SPRING (SW), TENSION254 4-251-844-01 GEAR (SS2)255 4-251-835-01 GEAR (STOCKER 1)
256 4-251-833-01 LEVER (SUB TRAY)257 4-251-843-01 LEVER (RELEASE)258 4-251-831-01 LEVER (MODE)259 4-251-862-01 SHUTTER (TRAY)260 4-251-845-01 GEAR (SS3)
261 4-251-829-01 TRAY (SUB)262 4-251-827-01 CAM (STOCKER)263 4-251-836-01 GEAR (STOCKER 2)
The components identified bymark 0 or dotted line with mark0 are critical for safety.Replace only with part numberspecified.
264 4-251-838-01 GEAR (STOCKER 3)265 4-251-823-01 CHASSIS (CDM81)
266 A-4750-232-A RELAY MOUNTED PC BOARD267 4-239-618-02 SCREW (+PWH, 2X6), STEP TAPPING268 4-251-825-01 CAM (BU)269 4-251-832-01 LEVER (STOCKER)270 4-251-861-01 LEVER (SW)
271 4-251-839-01 GEAR (STOCKER 4)272 4-251-840-01 GEAR (SUB TRAY)273 4-251-847-01 GEAR (SS4)S781 1-478-551-11 ENCODER, ROTARY#3 7-685-534-19 SCREW +BTP 2.6X8 TYPE2 N-S
#4 7-685-902-21 SCREW +PTPWH 2.6X8 (TYPE2)
53
HCD-CPX22/NXM3
8-7. BASE UNIT (BU-F1BD81A)
308
307
305
305305
305
304
304
304
304
303
303
303
303
302
301
306
Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks
301 X-4956-102-1 HOLDER (215) ASSY0302 8-820-244-01 OPTICAL PICK-UP (KSM-215DCP/C2NP)
303 4-227-549-11 INSULATOR304 4-227-045-11 SPRING (INSULATOR), COIL305 4-985-672-01 SCREW (+PTPWHM2.6), FLOATING
306 1-827-992-11 WIRE (FLAT TYPE) (16 CORE)307 A-4751-045-A CD (A) BOARD, COMPLETE308 4-951-620-01 SCREW (2.6X8), +BVTP
The components identified bymark 0 or dotted line with mark0 are critical for safety.Replace only with part numberspecified.
54
HCD-CPX22/NXM3SECTION 9
ELECTRICAL PARTS LIST
Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks
NOTE:• Due to standardization, replacements in the
parts list may be different from the partsspecified in the diagrams or the componentsused on the set.
• -XX, -X mean standardized parts, so theymay have some difference from the originalone.
• Items marked “*” are not stocked since theyare seldom required for routine service.Some delay should be anticipated whenordering these items.
• CAPACITORS:uF: µF
• RESISTORSAll resistors are in ohms.METAL: metal-film resistorMETAL OXIDE: Metal Oxide-film resistorF: nonflammable
• COILSuH: µH
• SEMICONDUCTORSIn each case, u: µ, for example:uA...: µA... , uPA... , µPA... ,uPB... , µPB... , uPC... , µPC... ,uPD..., µPD...
• AbbreviationE3 : 240V AC Area in E modelE51 : Chilean and Peruvian modelEA : Saudi Arabia modelRU : Russian model
BD
The components identified by mark 0or dotted line with mark 0 are criticalfor safety.Replace only with part number specified.
When indicating parts by referencenumber, please include the board.
A-4751-045-A BD BOARD, COMPLETE*****************
< CAPACITOR >
C10 1-165-989-11 CERAMIC CHIP 10uF 10% 6.3VC11 1-165-989-11 CERAMIC CHIP 10uF 10% 6.3VC14 1-164-360-11 CERAMIC CHIP 0.1uF 16VC15 1-164-360-11 CERAMIC CHIP 0.1uF 16VC16 1-115-156-11 CERAMIC CHIP 1uF 10V
C17 1-126-246-11 ELECT CHIP 220uF 20% 4VC18 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50VC111 1-162-967-11 CERAMIC CHIP 0.0033uF 10% 50VC112 1-164-315-11 CERAMIC CHIP 470PF 5% 50VC113 1-162-967-11 CERAMIC CHIP 0.0033uF 10% 50V
C114 1-164-315-11 CERAMIC CHIP 470PF 5% 50VC115 1-164-360-11 CERAMIC CHIP 0.1uF 16VC116 1-128-995-21 ELECT CHIP 100uF 20% 10VC122 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16VC123 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V
C124 1-162-959-11 CERAMIC CHIP 330PF 5% 50VC125 1-164-360-11 CERAMIC CHIP 0.1uF 16VC131 1-162-927-11 CERAMIC CHIP 100PF 5% 50VC132 1-117-863-11 CERAMIC CHIP 0.47uF 10% 6.3VC133 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
C134 1-164-360-11 CERAMIC CHIP 0.1uF 16VC141 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16VC142 1-162-965-11 CERAMIC CHIP 0.0015uF 10% 50VC143 1-164-360-11 CERAMIC CHIP 0.1uF 16VC151 1-128-995-21 ELECT CHIP 100uF 20% 10V
C161 1-164-360-11 CERAMIC CHIP 0.1uF 16VC162 1-164-360-11 CERAMIC CHIP 0.1uF 16VC163 1-164-360-11 CERAMIC CHIP 0.1uF 16VC171 1-162-919-11 CERAMIC CHIP 22PF 5% 50VC172 1-162-920-11 CERAMIC CHIP 27PF 5% 50V
C174 1-164-360-11 CERAMIC CHIP 0.1uF 16VC181 1-164-360-11 CERAMIC CHIP 0.1uF 16VC182 1-164-360-11 CERAMIC CHIP 0.1uF 16VC183 1-124-778-00 ELECT CHIP 22uF 20% 6.3VC184 1-124-778-00 ELECT CHIP 22uF 20% 6.3V
C185 1-164-315-11 CERAMIC CHIP 470PF 5% 50VC186 1-164-315-11 CERAMIC CHIP 470PF 5% 50VC194 1-164-360-11 CERAMIC CHIP 0.1uF 16V
C195 1-164-360-11 CERAMIC CHIP 0.1uF 16VC196 1-164-360-11 CERAMIC CHIP 0.1uF 16V
C201 1-128-995-21 ELECT CHIP 100uF 20% 10VC203 1-128-995-21 ELECT CHIP 100uF 20% 10VC209 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25VC210 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16VC211 1-164-230-11 CERAMIC CHIP 220PF 5% 50V
C212 1-162-919-11 CERAMIC CHIP 22PF 5% 50VC213 1-162-919-11 CERAMIC CHIP 22PF 5% 50VC251 1-162-969-11 CERAMIC CHIP 0.0068uF 10% 25VC252 1-164-360-11 CERAMIC CHIP 0.1uF 16VC255 1-164-360-11 CERAMIC CHIP 0.1uF 16V
C257 1-164-360-11 CERAMIC CHIP 0.1uF 16VC258 1-164-360-11 CERAMIC CHIP 0.1uF 16VC259 1-164-360-11 CERAMIC CHIP 0.1uF 16VC260 1-128-394-11 ELECT CHIP 220uF 20% 10VC302 1-164-360-11 CERAMIC CHIP 0.1uF 16V
C303 1-164-360-11 CERAMIC CHIP 0.1uF 16VC305 1-126-246-11 ELECT CHIP 220uF 20% 4VC306 1-164-360-11 CERAMIC CHIP 0.1uF 16VC307 1-164-360-11 CERAMIC CHIP 0.1uF 16VC308 1-126-208-21 ELECT CHIP 47uF 20% 4V
C309 1-164-360-11 CERAMIC CHIP 0.1uF 16VC310 1-164-360-11 CERAMIC CHIP 0.1uF 16VC311 1-164-360-11 CERAMIC CHIP 0.1uF 16VC312 1-164-360-11 CERAMIC CHIP 0.1uF 16VC313 1-164-360-11 CERAMIC CHIP 0.1uF 16V
C314 1-126-208-21 ELECT CHIP 47uF 20% 4VC315 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16VC316 1-162-966-11 CERAMIC CHIP 0.0022uF 10% 50VC317 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25VC318 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
C320 1-216-864-11 SHORT CHIP 0
< CONNECTOR >
CN101 1-770-425-11 CONNECTOR, FFC/FPC 16PCN201 1-818-350-11 CONNECTOR (FFC) 27P
< FERRITE BEAD >
FB301 1-500-445-21 FERRITE, EMI (SMD) (2012)
55
HCD-CPX22/NXM3
Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks
BD
< IC >
IC101 8-752-425-12 IC CXD3059ARIC251 6-705-808-01 IC BA5947FMIC301 6-705-365-01 IC TC94A34FG-002IC303 6-705-807-01 IC BH15FB1WG
< TRANSISTOR >
Q10 6-550-363-01 TRANSISTOR 2SB1690KT146
< RESISTOR >
R10 1-216-791-11 METAL CHIP 3.3 5% 1/10WR11 1-216-864-11 SHORT CHIP 0R12 1-216-845-11 METAL CHIP 100K 5% 1/10WR13 1-218-446-11 METAL CHIP 1 5% 1/10WR111 1-216-821-11 METAL CHIP 1K 5% 1/10W
R112 1-216-835-11 METAL CHIP 15K 5% 1/10WR113 1-216-821-11 METAL CHIP 1K 5% 1/10WR114 1-216-835-11 METAL CHIP 15K 5% 1/10WR121 1-216-835-11 METAL CHIP 15K 5% 1/10WR131 1-216-857-11 METAL CHIP 1M 5% 1/10W
R132 1-216-833-11 METAL CHIP 10K 5% 1/10WR133 1-216-848-11 METAL CHIP 180K 5% 1/10WR141 1-216-829-11 METAL CHIP 4.7K 5% 1/10WR142 1-216-821-11 METAL CHIP 1K 5% 1/10WR143 1-216-827-11 METAL CHIP 3.3K 5% 1/10W
R151 1-216-864-11 SHORT CHIP 0R161 1-216-809-11 METAL CHIP 100 5% 1/10WR162 1-216-841-11 METAL CHIP 47K 5% 1/10WR163 1-216-809-11 METAL CHIP 100 5% 1/10WR165 1-216-864-11 SHORT CHIP 0
R171 1-216-817-11 METAL CHIP 470 5% 1/10WR172 1-216-857-11 METAL CHIP 1M 5% 1/10WR173 1-216-295-91 SHORT CHIP 0R181 1-216-809-11 METAL CHIP 100 5% 1/10WR182 1-216-809-11 METAL CHIP 100 5% 1/10WR191 1-216-864-11 SHORT CHIP 0R201 1-500-445-21 FERRITE, EMI (SMD) (2012)R203 1-216-864-11 SHORT CHIP 0
R204 1-500-445-21 FERRITE, EMI (SMD) (2012)R205 1-216-864-11 SHORT CHIP 0R251 1-216-833-11 METAL CHIP 10K 5% 1/10WR252 1-216-837-11 METAL CHIP 22K 5% 1/10WR253 1-216-833-11 METAL CHIP 10K 5% 1/10W
R301 1-216-845-11 METAL CHIP 100K 5% 1/10WR302 1-216-833-11 METAL CHIP 10K 5% 1/10WR303 1-216-845-11 METAL CHIP 100K 5% 1/10WR305 1-216-845-11 METAL CHIP 100K 5% 1/10WR306 1-216-864-11 SHORT CHIP 0
R307 1-216-833-11 METAL CHIP 10K 5% 1/10WR313 1-216-813-11 METAL CHIP 220 5% 1/10WR351 1-216-809-11 METAL CHIP 100 5% 1/10WR352 1-216-809-11 METAL CHIP 100 5% 1/10WR353 1-216-809-11 METAL CHIP 100 5% 1/10W
R354 1-216-809-11 METAL CHIP 100 5% 1/10WR401 1-216-809-11 METAL CHIP 100 5% 1/10WR402 1-216-809-11 METAL CHIP 100 5% 1/10WR403 1-216-809-11 METAL CHIP 100 5% 1/10WR404 1-216-809-11 METAL CHIP 100 5% 1/10W
R405 1-216-809-11 METAL CHIP 100 5% 1/10WR406 1-216-809-11 METAL CHIP 100 5% 1/10WR407 1-216-809-11 METAL CHIP 100 5% 1/10WR408 1-216-809-11 METAL CHIP 100 5% 1/10WR409 1-216-809-11 METAL CHIP 100 5% 1/10W
R410 1-216-809-11 METAL CHIP 100 5% 1/10WR411 1-216-809-11 METAL CHIP 100 5% 1/10WR412 1-216-809-11 METAL CHIP 100 5% 1/10WR419 1-216-809-11 METAL CHIP 100 5% 1/10W
< SWITCH >
S101 1-771-853-11 SWITCH, DETECTION (LIMIT)
< VIBRATOR >
X171 1-767-408-21 VIBRATOR, CRYSTAL (16.9MHz)************************************************************
DISC SW BOARD*************
< CAPACITOR >
C1009 1-164-156-11 CERAMIC CHIP 0.1uF 25V
< DIODE >
D1001 8-719-058-64 DIODE SEL5823A-TP15 (DISC 1)D1002 8-719-058-64 DIODE SEL5823A-TP15 (DISC 2)D1003 8-719-058-64 DIODE SEL5823A-TP15 (DISC 3)D1004 8-719-058-64 DIODE SEL5823A-TP15 (DISC 4)D1005 8-719-058-64 DIODE SEL5823A-TP15 (DISC 5)
< TRANSISTOR >
Q1001 8-729-027-43 TRANSISTOR DTC114EKA-T146Q1002 8-729-027-43 TRANSISTOR DTC114EKA-T146Q1003 8-729-027-43 TRANSISTOR DTC114EKA-T146Q1004 8-729-027-43 TRANSISTOR DTC114EKA-T146Q1005 8-729-027-43 TRANSISTOR DTC114EKA-T146
< RESISTOR >
R1001 1-216-819-11 METAL CHIP 680 5% 1/10WR1002 1-216-819-11 METAL CHIP 680 5% 1/10WR1003 1-216-819-11 METAL CHIP 680 5% 1/10WR1004 1-216-819-11 METAL CHIP 680 5% 1/10WR1005 1-216-819-11 METAL CHIP 680 5% 1/10W
R1006 1-216-819-11 METAL CHIP 680 5% 1/10WR1007 1-216-819-11 METAL CHIP 680 5% 1/10WR1008 1-216-819-11 METAL CHIP 680 5% 1/10WR1009 1-216-819-11 METAL CHIP 680 5% 1/10WR1010 1-216-819-11 METAL CHIP 680 5% 1/10W
R1011 1-216-813-11 METAL CHIP 220 5% 1/10WR1012 1-216-815-11 METAL CHIP 330 5% 1/10WR1013 1-216-817-11 METAL CHIP 470 5% 1/10WR1014 1-216-819-11 METAL CHIP 680 5% 1/10W
< SWITCH >
S1001 1-762-875-21 SWITCH, KEYBOARD (DISC 1)S1002 1-762-875-21 SWITCH, KEYBOARD (DISC 2)S1003 1-762-875-21 SWITCH, KEYBOARD (DISC 3)S1004 1-762-875-21 SWITCH, KEYBOARD (DISC 4)S1005 1-762-875-21 SWITCH, KEYBOARD (DISC 5)
************************************************************
DISC SW
56
HCD-CPX22/NXM3
Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks
HP BOARD********
< CAPACITOR >
C1093 1-162-971-11 CERAMIC CHIP 0.001uF 10% 50VC1094 1-162-971-11 CERAMIC CHIP 0.001uF 10% 50V
< CONNECTOR >
CN1062 1-785-330-11 PIN, CONNECTOR (LIGHT ANGLE) 4P
< FERRITE BEAD >
FB1001 1-500-245-11 INDUCTOR, FERRITE BEADFB1002 1-500-245-11 INDUCTOR, FERRITE BEADFB1003 1-500-245-11 INDUCTOR, FERRITE BEADFB1004 1-500-245-11 INDUCTOR, FERRITE BEAD
< JACK >
J1063 1-750-032-11 JACK (DIA. 3.5) (PHONES)
< SHORT >
JR1080 1-216-864-11 SHORT CHIP 0JR1081 1-216-864-11 SHORT CHIP 0
< RESISTOR >
R1088 1-216-864-11 SHORT CHIP 0************************************************************
A-1052-039-A MAIN BOARD, COMPLETE (EA)A-4750-856-A MAIN BOARD, COMPLETE (AEP, UK)A-4750-931-A MAIN BOARD, COMPLETE (RU)A-4750-933-A MAIN BOARD, COMPLETE (E3)A-4750-935-A MAIN BOARD, COMPLETE (E51)A-4750-937-A MAIN BOARD, COMPLETE (US)
********************
7-685-646-79 SCREW +BVTP 3X8 TYPE2 IT-3
< CAPACITOR >
C1 1-126-964-11 ELECT 10uF 20% 50VC2 1-126-964-11 ELECT 10uF 20% 50VC21 1-126-963-11 ELECT 4.7uF 20% 50VC22 1-126-963-11 ELECT 4.7uF 20% 50VC25 1-126-963-11 ELECT 4.7uF 20% 50V
C26 1-126-963-11 ELECT 4.7uF 20% 50VC27 1-104-658-91 ELECT 100uF 20% 10VC28 1-104-658-91 ELECT 100uF 20% 10VC35 1-164-156-11 CERAMIC CHIP 0.1uF 25VC36 1-164-156-11 CERAMIC CHIP 0.1uF 25V
C37 1-164-156-11 CERAMIC CHIP 0.1uF 25VC38 1-164-156-11 CERAMIC CHIP 0.1uF 25VC39 1-164-156-11 CERAMIC CHIP 0.1uF 25VC40 1-164-156-11 CERAMIC CHIP 0.1uF 25VC70 1-162-919-11 CERAMIC CHIP 22PF 5% 50V
C75 1-126-964-11 ELECT 10uF 20% 50VC77 1-126-925-91 ELECT 470uF 20% 10VC79 1-126-964-11 ELECT 10uF 20% 50V
C85 1-126-964-11 ELECT 10uF 20% 50VC87 1-126-925-91 ELECT 470uF 20% 10V
C89 1-126-964-11 ELECT 10uF 20% 50VC90 1-162-919-11 CERAMIC CHIP 22PF 5% 50VC93 1-126-926-11 ELECT 1000uF 20% 10VC94 1-104-658-91 ELECT 100uF 20% 10VC100 1-164-156-11 CERAMIC CHIP 0.1uF 25V
C101 1-126-964-11 ELECT 10uF 20% 50VC102 1-126-964-11 ELECT 10uF 20% 50VC103 1-126-964-11 ELECT 10uF 20% 50VC104 1-126-964-11 ELECT 10uF 20% 50VC105 1-136-497-81 FILM 0.1uF 5% 50V
C106 1-126-964-11 ELECT 10uF 20% 50VC107 1-164-227-11 CERAMIC CHIP 0.022uF 10% 25VC108 1-164-227-11 CERAMIC CHIP 0.022uF 10% 25VC109 1-126-964-11 ELECT 10uF 20% 50VC110 1-165-176-11 CERAMIC CHIP 0.047uF 10% 16V
C111 1-164-174-11 CERAMIC CHIP 0.0082uF 10% 25VC112 1-126-964-11 ELECT 10uF 20% 50VC115 1-126-964-11 ELECT 10uF 20% 50VC116 1-126-964-11 ELECT 10uF 20% 50VC117 1-126-960-11 ELECT 1uF 20% 50V
C118 1-130-483-00 MYLAR 0.01uF 5% 50VC119 1-126-947-11 ELECT 47uF 20% 35VC121 1-136-177-00 FILM 1uF 5% 50VC122 1-126-963-11 ELECT 4.7uF 20% 50VC123 1-164-156-11 CERAMIC CHIP 0.1uF 25V
C124 1-104-658-91 ELECT 100uF 20% 10VC125 1-104-658-91 ELECT 100uF 20% 10VC126 1-104-658-91 ELECT 100uF 20% 10VC127 1-104-658-91 ELECT 100uF 20% 10VC131 1-162-919-11 CERAMIC CHIP 22PF 5% 50V
C132 1-130-483-00 MYLAR 0.01uF 5% 50VC133 1-130-483-00 MYLAR 0.01uF 5% 50VC134 1-126-964-11 ELECT 10uF 20% 50VC135 1-126-960-11 ELECT 1uF 20% 50VC141 1-162-960-11 CERAMIC CHIP 220PF 10% 50V
C142 1-126-964-11 ELECT 10uF 20% 50VC146 1-162-969-11 CERAMIC CHIP 0.0068uF 10% 25VC147 1-162-927-11 CERAMIC CHIP 100PF 5% 50VC148 1-162-927-11 CERAMIC CHIP 100PF 5% 50VC150 1-163-077-00 CERAMIC CHIP 0.1uF 50V
C151 1-126-964-11 ELECT 10uF 20% 50VC152 1-126-964-11 ELECT 10uF 20% 50VC154 1-126-964-11 ELECT 10uF 20% 50VC155 1-136-497-81 FILM 0.1uF 5% 50VC156 1-126-964-11 ELECT 10uF 20% 50V
C157 1-164-227-11 CERAMIC CHIP 0.022uF 10% 25VC158 1-164-227-11 CERAMIC CHIP 0.022uF 10% 25VC159 1-126-964-11 ELECT 10uF 20% 50VC160 1-165-176-11 CERAMIC CHIP 0.047uF 10% 16VC161 1-164-174-11 CERAMIC CHIP 0.0082uF 10% 25V
C162 1-126-964-11 ELECT 10uF 20% 50VC165 1-126-964-11 ELECT 10uF 20% 50VC166 1-126-964-11 ELECT 10uF 20% 50V
HP MAIN
57
HCD-CPX22/NXM3
Ref. No. Part No. Description Remarks Ref. No. Part No. Description RemarksRef. No. Part No. Description Remarks
MAIN
C167 1-126-960-11 ELECT 1uF 20% 50VC168 1-130-483-00 MYLAR 0.01uF 5% 50V
C169 1-126-947-11 ELECT 47uF 20% 35VC173 1-162-960-11 CERAMIC CHIP 220PF 10% 50VC174 1-162-960-11 CERAMIC CHIP 220PF 10% 50VC183 1-126-960-11 ELECT 1uF 20% 50VC191 1-162-960-11 CERAMIC CHIP 220PF 10% 50V
C192 1-126-964-11 ELECT 10uF 20% 50VC196 1-162-969-11 CERAMIC CHIP 0.0068uF 10% 25VC197 1-162-927-11 CERAMIC CHIP 100PF 5% 50VC198 1-162-927-11 CERAMIC CHIP 100PF 5% 50VC270 1-126-964-11 ELECT 10uF 20% 50V
C271 1-126-964-11 ELECT 10uF 20% 50VC301 1-162-961-11 CERAMIC CHIP 330PF 10% 50VC302 1-126-964-11 ELECT 10uF 20% 50VC303 1-162-961-11 CERAMIC CHIP 330PF 10% 50VC304 1-126-964-11 ELECT 10uF 20% 50V
C305 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50VC306 1-162-927-11 CERAMIC CHIP 100PF 5% 50VC307 1-162-961-11 CERAMIC CHIP 330PF 10% 50VC308 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25VC311 1-130-481-00 MYLAR 0.0068uF 5% 50V
C312 1-130-483-00 MYLAR 0.01uF 5% 50VC313 1-126-947-11 ELECT 47uF 20% 35VC314 1-137-150-11 FILM 0.01uF 5% 100VC315 1-130-479-00 MYLAR 0.0047uF 5% 50VC322 1-162-968-11 CERAMIC CHIP 0.0047uF 10% 50V
C324 1-162-968-11 CERAMIC CHIP 0.0047uF 10% 50VC351 1-162-961-11 CERAMIC CHIP 330PF 10% 50VC352 1-126-964-11 ELECT 10uF 20% 50VC353 1-162-961-11 CERAMIC CHIP 330PF 10% 50VC354 1-126-964-11 ELECT 10uF 20% 50V
C355 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50VC356 1-162-927-11 CERAMIC CHIP 100PF 5% 50VC357 1-162-961-11 CERAMIC CHIP 330PF 10% 50VC358 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25VC370 1-104-658-91 ELECT 100uF 20% 10V
C372 1-104-655-91 ELECT 470uF 20% 6.3VC373 1-164-156-11 CERAMIC CHIP 0.1uF 25VC375 1-126-916-11 ELECT 1000uF 20% 6.3VC379 1-104-655-91 ELECT 470uF 20% 6.3VC382 1-126-925-91 ELECT 470uF 20% 10V
C383 1-164-156-11 CERAMIC CHIP 0.1uF 25VC384 1-104-655-91 ELECT 470uF 20% 6.3VC390 1-126-965-91 ELECT 22uF 20% 50VC391 1-136-497-81 FILM 0.1uF 5% 50VC392 1-136-497-81 FILM 0.1uF 5% 50V
C393 1-126-964-11 ELECT 10uF 20% 50VC410 1-162-918-11 CERAMIC CHIP 18PF 5% 50VC411 1-162-918-11 CERAMIC CHIP 18PF 5% 50VC412 1-164-156-11 CERAMIC CHIP 0.1uF 25VC416 1-164-156-11 CERAMIC CHIP 0.1uF 25V
C417 1-126-916-11 ELECT 1000uF 20% 6.3VC462 1-104-658-91 ELECT 100uF 20% 10VC463 1-164-156-11 CERAMIC CHIP 0.1uF 25VC475 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25VC476 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
C497 1-164-156-11 CERAMIC CHIP 0.1uF 25VC498 1-126-964-11 ELECT 10uF 20% 50VC499 1-164-156-11 CERAMIC CHIP 0.1uF 25VC900 1-126-937-11 ELECT 4700uF 20% 16VC901 1-126-956-91 ELECT 0.1uF 20% 50V
C902 1-104-658-91 ELECT 100uF 20% 10VC903 1-126-964-11 ELECT 10uF 20% 50VC904 1-104-658-91 ELECT 100uF 20% 10VC905 1-126-956-91 ELECT 0.1uF 20% 50VC906 1-104-658-91 ELECT 100uF 20% 10V
C919 1-126-964-11 ELECT 10uF 20% 50VC920 1-126-964-11 ELECT 10uF 20% 50VC930 1-126-768-11 ELECT 2200uF 20% 16VC952 1-164-156-11 CERAMIC CHIP 0.1uF 25VC953 1-164-156-11 CERAMIC CHIP 0.1uF 25V
C972 1-164-156-11 CERAMIC CHIP 0.1uF 25VC973 1-164-156-11 CERAMIC CHIP 0.1uF 25V
< CONNECTOR >
CN101 1-691-768-11 PLUG (MICRO CONNECTOR) 6PCN105 1-691-765-11 PLUG (MICRO CONNECTOR) 3PCN106 1-784-780-11 CONNECTOR, FFC 19PCN107 1-785-316-11 PIN, CONNECTOR (STRAIGHT) 4PCN109 1-784-774-11 CONNECTOR, FFC 13P
CN110 1-784-776-11 CONNECTOR, FFC 15PCN112 1-784-766-11 CONNECTOR, FFC 5PCN204 1-568-830-11 CONNECTOR, FFC 11P (EXCEPT AEP, UK)CN204 1-784-776-11 CONNECTOR, FFC 15P (AEP, UK)
* CN301 1-564-719-11 PIN, CONNECTOR (SMALL TYPE) 3P
* CN302 1-564-724-11 PIN, CONNECTOR (SMALL TYPE) 8PCN303 1-784-774-11 CONNECTOR, FFC 13P
* CN304 1-568-449-11 HOUSING, CONNECTOR (PC BOARD) 3PCN371 1-779-295-11 CONNECTOR, FFC (LIF (NON-ZIF)) 27PCN372 1-779-289-11 CONNECTOR, FFC (LIF (NON-ZIF)) 21P
CN401 1-785-316-11 PIN, CONNECTOR (STRAIGHT) 4P
< DIODE >
D181 8-719-988-61 DIODE 1SS355TE-17D182 8-719-988-61 DIODE 1SS355TE-17D183 8-719-988-61 DIODE 1SS355TE-17D321 8-719-988-61 DIODE 1SS355TE-17D322 8-719-988-61 DIODE 1SS355TE-17
D371 6-500-522-31 DIODE 10EDB40-TB5D372 6-500-522-31 DIODE 10EDB40-TB5D373 6-500-522-31 DIODE 10EDB40-TB5D391 8-719-988-61 DIODE 1SS355TE-17D392 8-719-988-61 DIODE 1SS355TE-17
D393 8-719-988-61 DIODE 1SS355TE-17D394 8-719-988-61 DIODE 1SS355TE-17D395 8-719-988-61 DIODE 1SS355TE-17D396 8-719-988-61 DIODE 1SS355TE-17D397 8-719-988-61 DIODE 1SS355TE-17
D903 6-500-522-31 DIODE 10EDB40-TB5D904 8-719-988-61 DIODE 1SS355TE-17D905 8-719-083-58 DIODE UDZSTE-173.9B
58
HCD-CPX22/NXM3
Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks
MAIN
< EARTH TERMINAL >
EP901 1-537-738-21 TERMINAL, GROUND
< FERRITE BEAD >
FB30 1-469-125-21 FERRITE, EMI (SMD) (1608)FB34 1-469-125-21 FERRITE, EMI (SMD) (1608)FB50 1-469-125-21 FERRITE, EMI (SMD) (1608)FB54 1-469-125-21 FERRITE, EMI (SMD) (1608)FB80 1-469-125-21 FERRITE, EMI (SMD) (1608)
FB84 1-469-125-21 FERRITE, EMI (SMD) (1608)FB371 1-216-864-11 SHORT CHIP 0FB372 1-216-864-11 SHORT CHIP 0FB373 1-216-864-11 SHORT CHIP 0FB374 1-216-864-11 SHORT CHIP 0
< IC >
IC3 8-759-359-49 IC NJM3414AV (TE2)IC101 6-705-667-01 IC M61537FP-RF0GIC301 8-749-019-25 IC TOTX141 (DIGITAL OUT)IC391 8-759-532-64 IC M62703SL-TPIC401 6-803-926-01 IC M30622MGN-B28FPU0
IC901 8-759-701-59 IC NJM78M09FAIC902 8-759-701-59 IC NJM78M09FAIC903 6-702-771-01 IC TA78033LSIC951 6-703-679-11 IC PT8300R-TPIC971 6-703-679-11 IC PT8300R-TP
< JACK >
J102 1-778-940-11 JACK 2P (VIDEO(MD))
< SHORT >
JR1 1-216-864-11 SHORT CHIP 0JR101 1-216-864-11 SHORT CHIP 0JR102 1-216-864-11 SHORT CHIP 0JR103 1-216-296-11 SHORT CHIP 0JR104 1-216-296-11 SHORT CHIP 0
JR105 1-216-296-11 SHORT CHIP 0JR106 1-216-864-11 SHORT CHIP 0JR107 1-216-296-11 SHORT CHIP 0JR108 1-216-296-11 SHORT CHIP 0JR109 1-216-296-11 SHORT CHIP 0
JR110 1-216-864-11 SHORT CHIP 0JR111 1-216-296-11 SHORT CHIP 0JR112 1-216-864-11 SHORT CHIP 0JR113 1-216-296-11 SHORT CHIP 0JR114 1-216-864-11 SHORT CHIP 0
JR115 1-216-296-11 SHORT CHIP 0JR116 1-216-864-11 SHORT CHIP 0JR117 1-216-296-11 SHORT CHIP 0JR118 1-216-864-11 SHORT CHIP 0JR119 1-216-864-11 SHORT CHIP 0
JR120 1-216-864-11 SHORT CHIP 0JR121 1-216-864-11 SHORT CHIP 0JR122 1-216-296-11 SHORT CHIP 0JR123 1-216-864-11 SHORT CHIP 0JR124 1-216-296-11 SHORT CHIP 0
JR125 1-216-864-11 SHORT CHIP 0JR126 1-216-296-11 SHORT CHIP 0JR127 1-216-296-11 SHORT CHIP 0JR128 1-216-864-11 SHORT CHIP 0JR203 1-216-864-11 SHORT CHIP 0
JR204 1-216-296-11 SHORT CHIP 0JR205 1-216-296-11 SHORT CHIP 0JR206 1-216-296-11 SHORT CHIP 0JR261 1-216-296-11 SHORT CHIP 0JR418 1-216-864-11 SHORT CHIP 0 (EXCEPT AEP, UK)
JR449 1-216-864-11 SHORT CHIP 0 (EXCEPT AEP, UK)
< COIL >
L301 1-410-780-11 INDUCTOR 27mHL311 1-414-189-31 INDUCTOR 100uHL351 1-410-780-11 INDUCTOR 27mHL370 1-412-064-11 INDUCTOR 100uHL951 1-216-296-11 SHORT CHIP 0
L971 1-216-296-11 SHORT CHIP 0
< TRANSISTOR >
Q1 6-550-889-01 TRANSISTOR 2SC5938-T112-1BQ2 6-550-889-01 TRANSISTOR 2SC5938-T112-1BQ21 8-729-027-43 TRANSISTOR DTC114EKA-T146Q22 8-729-027-23 TRANSISTOR DTA114EKA-T146Q25 8-729-027-43 TRANSISTOR DTC114EKA-T146
Q26 8-729-027-23 TRANSISTOR DTA114EKA-T146Q27 8-729-027-43 TRANSISTOR DTC114EKA-T146Q28 8-729-027-23 TRANSISTOR DTA114EKA-T146Q29 8-729-027-43 TRANSISTOR DTC114EKA-T146Q30 8-729-027-23 TRANSISTOR DTA114EKA-T146
Q31 8-729-027-43 TRANSISTOR DTC114EKA-T146Q32 8-729-027-23 TRANSISTOR DTA114EKA-T146Q33 8-729-027-43 TRANSISTOR DTC114EKA-T146Q34 8-729-027-23 TRANSISTOR DTA114EKA-T146Q71 6-550-889-01 TRANSISTOR 2SC5938-T112-1B
Q81 6-550-889-01 TRANSISTOR 2SC5938-T112-1BQ82 8-729-142-48 TRANSISTOR 2SD1616-TP-LKQ103 6-550-889-01 TRANSISTOR 2SC5938-T112-1BQ104 6-550-889-01 TRANSISTOR 2SC5938-T112-1BQ140 6-550-889-01 TRANSISTOR 2SC5938-T112-1B
Q153 6-550-889-01 TRANSISTOR 2SC5938-T112-1BQ154 6-550-889-01 TRANSISTOR 2SC5938-T112-1BQ270 6-550-889-01 TRANSISTOR 2SC5938-T112-1BQ271 6-550-889-01 TRANSISTOR 2SC5938-T112-1BQ301 8-729-141-73 TRANSISTOR 2SC3624A-T1L15L16
Q302 8-729-141-73 TRANSISTOR 2SC3624A-T1L15L16Q303 8-729-141-73 TRANSISTOR 2SC3624A-T1L15L16Q311 8-729-216-22 TRANSISTOR 2SA1162-GQ312 8-729-027-43 TRANSISTOR DTC114EKA-T146Q313 8-729-027-43 TRANSISTOR DTC114EKA-T146
Q314 8-729-027-23 TRANSISTOR DTA114EKA-T146Q315 8-729-027-43 TRANSISTOR DTC114EKA-T146Q316 8-729-027-43 TRANSISTOR DTC114EKA-T146Q317 8-729-040-20 TRANSISTOR RT1P137L-TPQ318 8-729-142-46 TRANSISTOR 2SC2001-LK
59
HCD-CPX22/NXM3
Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks
MAIN
Q321 8-729-027-43 TRANSISTOR DTC114EKA-T146Q322 8-729-140-04 TRANSISTOR 2SB1116A-LQ323 8-729-027-43 TRANSISTOR DTC114EKA-T146Q324 8-729-140-04 TRANSISTOR 2SB1116A-LQ326 8-729-027-43 TRANSISTOR DTC114EKA-T146
Q327 8-729-140-04 TRANSISTOR 2SB1116A-LQ341 8-729-120-28 TRANSISTOR 2SC1623-L5L6Q342 8-729-027-43 TRANSISTOR DTC114EKA-T146Q343 8-729-027-43 TRANSISTOR DTC114EKA-T146Q351 8-729-141-73 TRANSISTOR 2SC3624A-T1L15L16
Q352 8-729-141-73 TRANSISTOR 2SC3624A-T1L15L16Q353 8-729-141-73 TRANSISTOR 2SC3624A-T1L15L16Q391 8-729-120-28 TRANSISTOR 2SC1623-L5L6Q906 8-729-120-28 TRANSISTOR 2SC1623-L5L6
< RESISTOR >
R1 1-216-825-11 METAL CHIP 2.2K 5% 1/10WR2 1-216-833-11 METAL CHIP 10K 5% 1/10WR3 1-216-821-11 METAL CHIP 1K 5% 1/10WR4 1-216-825-11 METAL CHIP 2.2K 5% 1/10WR5 1-216-833-11 METAL CHIP 10K 5% 1/10W
R6 1-216-821-11 METAL CHIP 1K 5% 1/10WR21 1-216-829-11 METAL CHIP 4.7K 5% 1/10WR22 1-216-837-11 METAL CHIP 22K 5% 1/10WR23 1-216-845-11 METAL CHIP 100K 5% 1/10WR27 1-216-829-11 METAL CHIP 4.7K 5% 1/10W
R28 1-216-837-11 METAL CHIP 22K 5% 1/10WR29 1-216-845-11 METAL CHIP 100K 5% 1/10WR30 1-216-829-11 METAL CHIP 4.7K 5% 1/10WR31 1-216-837-11 METAL CHIP 22K 5% 1/10WR32 1-216-845-11 METAL CHIP 100K 5% 1/10W
R33 1-216-845-11 METAL CHIP 100K 5% 1/10WR34 1-216-837-11 METAL CHIP 22K 5% 1/10WR35 1-216-845-11 METAL CHIP 100K 5% 1/10WR36 1-216-837-11 METAL CHIP 22K 5% 1/10WR37 1-216-845-11 METAL CHIP 100K 5% 1/10W
R38 1-216-837-11 METAL CHIP 22K 5% 1/10WR39 1-216-864-11 SHORT CHIP 0R50 1-216-841-11 METAL CHIP 47K 5% 1/10WR59 1-216-805-11 METAL CHIP 47 5% 1/10WR60 1-216-841-11 METAL CHIP 47K 5% 1/10W
R69 1-216-805-11 METAL CHIP 47 5% 1/10WR75 1-216-833-11 METAL CHIP 10K 5% 1/10WR76 1-216-841-11 METAL CHIP 47K 5% 1/10WR77 1-216-845-11 METAL CHIP 100K 5% 1/10WR78 1-216-821-11 METAL CHIP 1K 5% 1/10W
R79 1-216-805-11 METAL CHIP 47 5% 1/10WR80 1-216-833-11 METAL CHIP 10K 5% 1/10WR85 1-216-833-11 METAL CHIP 10K 5% 1/10WR86 1-216-841-11 METAL CHIP 47K 5% 1/10WR87 1-216-845-11 METAL CHIP 100K 5% 1/10W
R88 1-216-821-11 METAL CHIP 1K 5% 1/10WR89 1-216-805-11 METAL CHIP 47 5% 1/10WR90 1-216-833-11 METAL CHIP 10K 5% 1/10WR98 1-216-821-11 METAL CHIP 1K 5% 1/10WR101 1-216-835-11 METAL CHIP 15K 5% 1/10W
R102 1-216-841-11 METAL CHIP 47K 5% 1/10WR103 1-216-825-11 METAL CHIP 2.2K 5% 1/10W
R104 1-216-825-11 METAL CHIP 2.2K 5% 1/10WR105 1-216-833-11 METAL CHIP 10K 5% 1/10WR109 1-216-841-11 METAL CHIP 47K 5% 1/10W
R110 1-216-821-11 METAL CHIP 1K 5% 1/10WR111 1-216-821-11 METAL CHIP 1K 5% 1/10WR112 1-216-834-11 METAL CHIP 12K 5% 1/10WR113 1-216-851-11 METAL CHIP 330K 5% 1/10WR114 1-216-812-11 METAL CHIP 180 5% 1/10W
R118 1-216-809-11 METAL CHIP 100 5% 1/10WR119 1-216-833-11 METAL CHIP 10K 5% 1/10WR121 1-216-861-11 METAL CHIP 2.2M 5% 1/10WR122 1-216-835-11 METAL CHIP 15K 5% 1/10WR123 1-216-857-11 METAL CHIP 1M 5% 1/10W
R126 1-216-813-11 METAL CHIP 220 5% 1/10WR127 1-216-813-11 METAL CHIP 220 5% 1/10WR129 1-216-835-11 METAL CHIP 15K 5% 1/10WR130 1-216-809-11 METAL CHIP 100 5% 1/10WR131 1-216-825-11 METAL CHIP 2.2K 5% 1/10W
R132 1-216-838-11 METAL CHIP 27K 5% 1/10WR133 1-216-833-11 METAL CHIP 10K 5% 1/10WR141 1-216-821-11 METAL CHIP 1K 5% 1/10WR142 1-216-845-11 METAL CHIP 100K 5% 1/10WR151 1-216-835-11 METAL CHIP 15K 5% 1/10W
R152 1-216-841-11 METAL CHIP 47K 5% 1/10WR153 1-216-825-11 METAL CHIP 2.2K 5% 1/10WR154 1-216-825-11 METAL CHIP 2.2K 5% 1/10WR155 1-216-833-11 METAL CHIP 10K 5% 1/10WR159 1-216-841-11 METAL CHIP 47K 5% 1/10W
R160 1-216-821-11 METAL CHIP 1K 5% 1/10WR161 1-216-821-11 METAL CHIP 1K 5% 1/10WR162 1-216-834-11 METAL CHIP 12K 5% 1/10WR163 1-216-851-11 METAL CHIP 330K 5% 1/10WR164 1-216-812-11 METAL CHIP 180 5% 1/10W
R168 1-216-809-11 METAL CHIP 100 5% 1/10WR169 1-216-833-11 METAL CHIP 10K 5% 1/10WR180 1-216-809-11 METAL CHIP 100 5% 1/10WR186 1-216-864-11 SHORT CHIP 0R187 1-216-853-11 METAL CHIP 470K 5% 1/10W
R188 1-216-815-11 METAL CHIP 330 5% 1/10WR189 1-216-841-11 METAL CHIP 47K 5% 1/10WR191 1-216-821-11 METAL CHIP 1K 5% 1/10WR192 1-216-845-11 METAL CHIP 100K 5% 1/10WR241 1-216-864-11 SHORT CHIP 0
R243 1-216-864-11 SHORT CHIP 0R246 1-216-833-11 METAL CHIP 10K 5% 1/10WR247 1-216-833-11 METAL CHIP 10K 5% 1/10WR270 1-216-825-11 METAL CHIP 2.2K 5% 1/10WR272 1-216-821-11 METAL CHIP 1K 5% 1/10W
R273 1-216-825-11 METAL CHIP 2.2K 5% 1/10WR275 1-216-821-11 METAL CHIP 1K 5% 1/10WR294 1-216-821-11 METAL CHIP 1K 5% 1/10WR296 1-216-833-11 METAL CHIP 10K 5% 1/10WR298 1-216-821-11 METAL CHIP 1K 5% 1/10W
R299 1-216-833-11 METAL CHIP 10K 5% 1/10WR301 1-216-829-11 METAL CHIP 4.7K 5% 1/10WR302 1-216-829-11 METAL CHIP 4.7K 5% 1/10WR303 1-216-821-11 METAL CHIP 1K 5% 1/10WR304 1-216-835-11 METAL CHIP 15K 5% 1/10W
60
HCD-CPX22/NXM3
Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks
MAIN
R305 1-216-829-11 METAL CHIP 4.7K 5% 1/10WR306 1-216-832-11 METAL CHIP 8.2K 5% 1/10WR307 1-216-833-11 METAL CHIP 10K 5% 1/10WR309 1-216-825-11 METAL CHIP 2.2K 5% 1/10WR311 1-216-833-11 METAL CHIP 10K 5% 1/10W
R312 1-216-833-11 METAL CHIP 10K 5% 1/10WR313 1-216-833-11 METAL CHIP 10K 5% 1/10WR314 1-216-841-11 METAL CHIP 47K 5% 1/10WR315 1-216-829-11 METAL CHIP 4.7K 5% 1/10WR316 1-216-797-11 METAL CHIP 10 5% 1/10W
R317 1-216-833-11 METAL CHIP 10K 5% 1/10WR318 1-216-805-11 METAL CHIP 47 5% 1/10WR319 1-216-827-11 METAL CHIP 3.3K 5% 1/10WR320 1-216-803-11 METAL CHIP 33 5% 1/10WR321 1-216-825-11 METAL CHIP 2.2K 5% 1/10W
R322 1-216-825-11 METAL CHIP 2.2K 5% 1/10WR323 1-216-821-11 METAL CHIP 1K 5% 1/10WR324 1-216-825-11 METAL CHIP 2.2K 5% 1/10WR325 1-216-825-11 METAL CHIP 2.2K 5% 1/10WR326 1-216-821-11 METAL CHIP 1K 5% 1/10W
R327 1-216-825-11 METAL CHIP 2.2K 5% 1/10WR328 1-216-825-11 METAL CHIP 2.2K 5% 1/10WR329 1-216-841-11 METAL CHIP 47K 5% 1/10WR330 1-216-829-11 METAL CHIP 4.7K 5% 1/10WR331 1-216-841-11 METAL CHIP 47K 5% 1/10W
R332 1-216-829-11 METAL CHIP 4.7K 5% 1/10WR333 1-216-841-11 METAL CHIP 47K 5% 1/10WR334 1-216-841-11 METAL CHIP 47K 5% 1/10WR335 1-216-841-11 METAL CHIP 47K 5% 1/10WR336 1-216-841-11 METAL CHIP 47K 5% 1/10W
R337 1-216-837-11 METAL CHIP 22K 5% 1/10WR338 1-216-833-11 METAL CHIP 10K 5% 1/10WR339 1-216-841-11 METAL CHIP 47K 5% 1/10WR340 1-216-829-11 METAL CHIP 4.7K 5% 1/10WR341 1-216-833-11 METAL CHIP 10K 5% 1/10W
R342 1-216-829-11 METAL CHIP 4.7K 5% 1/10WR343 1-216-837-11 METAL CHIP 22K 5% 1/10WR344 1-216-833-11 METAL CHIP 10K 5% 1/10WR345 1-216-833-11 METAL CHIP 10K 5% 1/10WR347 1-216-825-11 METAL CHIP 2.2K 5% 1/10W
R351 1-216-829-11 METAL CHIP 4.7K 5% 1/10WR352 1-216-829-11 METAL CHIP 4.7K 5% 1/10WR353 1-216-821-11 METAL CHIP 1K 5% 1/10WR354 1-216-835-11 METAL CHIP 15K 5% 1/10WR355 1-216-829-11 METAL CHIP 4.7K 5% 1/10W
R356 1-216-832-11 METAL CHIP 8.2K 5% 1/10WR357 1-216-833-11 METAL CHIP 10K 5% 1/10WR359 1-216-825-11 METAL CHIP 2.2K 5% 1/10WR377 1-216-833-11 METAL CHIP 10K 5% 1/10WR378 1-216-833-11 METAL CHIP 10K 5% 1/10W
R379 1-216-833-11 METAL CHIP 10K 5% 1/10WR380 1-216-833-11 METAL CHIP 10K 5% 1/10WR381 1-216-833-11 METAL CHIP 10K 5% 1/10WR382 1-216-833-11 METAL CHIP 10K 5% 1/10WR383 1-216-833-11 METAL CHIP 10K 5% 1/10W
R384 1-216-833-11 METAL CHIP 10K 5% 1/10WR385 1-216-833-11 METAL CHIP 10K 5% 1/10WR386 1-216-833-11 METAL CHIP 10K 5% 1/10W
R387 1-216-833-11 METAL CHIP 10K 5% 1/10WR388 1-216-833-11 METAL CHIP 10K 5% 1/10W
R391 1-216-833-11 METAL CHIP 10K 5% 1/10WR392 1-216-837-11 METAL CHIP 22K 5% 1/10WR393 1-216-837-11 METAL CHIP 22K 5% 1/10WR394 1-216-829-11 METAL CHIP 4.7K 5% 1/10WR395 1-216-813-11 METAL CHIP 220 5% 1/10W
R396 1-216-833-11 METAL CHIP 10K 5% 1/10WR401 1-216-809-11 METAL CHIP 100 5% 1/10WR402 1-216-809-11 METAL CHIP 100 5% 1/10WR403 1-216-809-11 METAL CHIP 100 5% 1/10WR404 1-216-809-11 METAL CHIP 100 5% 1/10W
R405 1-216-809-11 METAL CHIP 100 5% 1/10WR406 1-216-809-11 METAL CHIP 100 5% 1/10WR407 1-216-809-11 METAL CHIP 100 5% 1/10WR408 1-216-833-11 METAL CHIP 10K 5% 1/10WR409 1-216-833-11 METAL CHIP 10K 5% 1/10W
R410 1-216-833-11 METAL CHIP 10K 5% 1/10WR411 1-216-851-11 METAL CHIP 330K 5% 1/10WR412 1-216-833-11 METAL CHIP 10K 5% 1/10WR413 1-216-864-11 SHORT CHIP 0R414 1-216-833-11 METAL CHIP 10K 5% 1/10W
R415 1-216-833-11 METAL CHIP 10K 5% 1/10WR416 1-216-833-11 METAL CHIP 10K 5% 1/10WR417 1-216-833-11 METAL CHIP 10K 5% 1/10WR418 1-216-809-11 METAL CHIP 100 5% 1/10W
(AEP, UK)R419 1-216-809-11 METAL CHIP 100 5% 1/10W
R420 1-216-829-11 METAL CHIP 4.7K 5% 1/10WR421 1-216-809-11 METAL CHIP 100 5% 1/10WR422 1-216-809-11 METAL CHIP 100 5% 1/10WR423 1-216-809-11 METAL CHIP 100 5% 1/10WR424 1-216-809-11 METAL CHIP 100 5% 1/10W
R425 1-216-809-11 METAL CHIP 100 5% 1/10WR426 1-216-809-11 METAL CHIP 100 5% 1/10WR429 1-216-809-11 METAL CHIP 100 5% 1/10WR430 1-216-809-11 METAL CHIP 100 5% 1/10WR431 1-216-809-11 METAL CHIP 100 5% 1/10W
R432 1-216-809-11 METAL CHIP 100 5% 1/10WR433 1-216-809-11 METAL CHIP 100 5% 1/10WR434 1-216-809-11 METAL CHIP 100 5% 1/10WR435 1-216-809-11 METAL CHIP 100 5% 1/10WR436 1-216-809-11 METAL CHIP 100 5% 1/10W
R437 1-216-809-11 METAL CHIP 100 5% 1/10WR438 1-216-809-11 METAL CHIP 100 5% 1/10WR439 1-216-809-11 METAL CHIP 100 5% 1/10WR440 1-216-809-11 METAL CHIP 100 5% 1/10WR441 1-216-809-11 METAL CHIP 100 5% 1/10W
R442 1-216-809-11 METAL CHIP 100 5% 1/10WR443 1-216-809-11 METAL CHIP 100 5% 1/10WR444 1-216-809-11 METAL CHIP 100 5% 1/10WR445 1-216-809-11 METAL CHIP 100 5% 1/10WR446 1-216-809-11 METAL CHIP 100 5% 1/10W
R447 1-216-809-11 METAL CHIP 100 5% 1/10WR448 1-216-809-11 METAL CHIP 100 5% 1/10WR449 1-216-809-11 METAL CHIP 100 5% 1/10W
(AEP, UK)R450 1-216-809-11 METAL CHIP 100 5% 1/10W
61
HCD-CPX22/NXM3
Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks
MAIN
R451 1-216-809-11 METAL CHIP 100 5% 1/10W
R452 1-216-809-11 METAL CHIP 100 5% 1/10WR453 1-216-809-11 METAL CHIP 100 5% 1/10WR454 1-216-809-11 METAL CHIP 100 5% 1/10WR455 1-216-809-11 METAL CHIP 100 5% 1/10WR456 1-216-809-11 METAL CHIP 100 5% 1/10W
R457 1-216-809-11 METAL CHIP 100 5% 1/10WR458 1-216-809-11 METAL CHIP 100 5% 1/10WR459 1-216-809-11 METAL CHIP 100 5% 1/10WR460 1-216-809-11 METAL CHIP 100 5% 1/10WR461 1-216-809-11 METAL CHIP 100 5% 1/10W
R465 1-216-809-11 METAL CHIP 100 5% 1/10WR466 1-216-833-11 METAL CHIP 10K 5% 1/10WR467 1-216-833-11 METAL CHIP 10K 5% 1/10WR468 1-216-833-11 METAL CHIP 10K 5% 1/10WR469 1-216-833-11 METAL CHIP 10K 5% 1/10W
R470 1-216-809-11 METAL CHIP 100 5% 1/10WR471 1-216-809-11 METAL CHIP 100 5% 1/10WR472 1-216-809-11 METAL CHIP 100 5% 1/10WR473 1-216-809-11 METAL CHIP 100 5% 1/10WR474 1-216-809-11 METAL CHIP 100 5% 1/10W
R476 1-216-809-11 METAL CHIP 100 5% 1/10WR477 1-216-809-11 METAL CHIP 100 5% 1/10WR478 1-216-809-11 METAL CHIP 100 5% 1/10WR479 1-216-809-11 METAL CHIP 100 5% 1/10WR482 1-216-809-11 METAL CHIP 100 5% 1/10W
R483 1-216-809-11 METAL CHIP 100 5% 1/10WR484 1-216-809-11 METAL CHIP 100 5% 1/10WR485 1-216-809-11 METAL CHIP 100 5% 1/10WR486 1-216-809-11 METAL CHIP 100 5% 1/10WR489 1-216-809-11 METAL CHIP 100 5% 1/10W
R490 1-216-809-11 METAL CHIP 100 5% 1/10WR492 1-216-811-11 METAL CHIP 150 5% 1/10W
(RU)R492 1-216-821-11 METAL CHIP 1K 5% 1/10W
(E51)R492 1-216-825-11 METAL CHIP 2.2K 5% 1/10W
(US)R492 1-216-829-11 METAL CHIP 4.7K 5% 1/10W
(E3, EA)
R492 1-216-864-11 SHORT CHIP 0 (AEP, UK)R493 1-216-809-11 METAL CHIP 100 5% 1/10WR494 1-216-827-11 METAL CHIP 3.3K 5% 1/10WR495 1-216-827-11 METAL CHIP 3.3K 5% 1/10WR496 1-216-821-11 METAL CHIP 1K 5% 1/10W
(EA)
R496 1-216-829-11 METAL CHIP 4.7K 5% 1/10W(EXCEPT E3, EA)
R496 1-216-864-11 SHORT CHIP 0 (E3)R497 1-216-833-11 METAL CHIP 10K 5% 1/10WR498 1-216-797-11 METAL CHIP 10 5% 1/10WR499 1-216-797-11 METAL CHIP 10 5% 1/10W
R914 1-216-821-11 METAL CHIP 1K 5% 1/10WR915 1-216-821-11 METAL CHIP 1K 5% 1/10WR952 1-216-809-11 METAL CHIP 100 5% 1/10WR953 1-216-809-11 METAL CHIP 100 5% 1/10WR954 1-216-809-11 METAL CHIP 100 5% 1/10W
R955 1-216-809-11 METAL CHIP 100 5% 1/10W
R956 1-216-809-11 METAL CHIP 100 5% 1/10WR957 1-216-809-11 METAL CHIP 100 5% 1/10WR958 1-216-809-11 METAL CHIP 100 5% 1/10WR959 1-216-809-11 METAL CHIP 100 5% 1/10W
R968 1-216-833-11 METAL CHIP 10K 5% 1/10WR970 1-216-833-11 METAL CHIP 10K 5% 1/10WR984 1-216-833-11 METAL CHIP 10K 5% 1/10W
< TRANSFORMER >
T301 1-433-372-11 TRANSFORMER, BIAS OSCILLATION
< VIBRATOR >
X401 1-567-098-41 VIBRATOR, CRYSTAL (32.768kHz)X402 1-795-482-11 VIBRATOR, CERAMIC (16MHz)
************************************************************
MOTOR BOARD***********
< SWITCH >
S761 1-786-704-11 SWITCH, LEVER (SUB TRAY OUT)************************************************************
A-4750-849-A PANEL BOARD, COMPLETE*******************
< CAPACITOR >
C1006 1-164-156-11 CERAMIC CHIP 0.1uF 25VC1021 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50VC1025 1-162-960-11 CERAMIC CHIP 220PF 10% 50VC1026 1-126-964-11 ELECT 10uF 20% 50VC1028 1-126-964-11 ELECT 10uF 20% 50V
C1029 1-131-992-91 CERAMIC CHIP 100000PF 35VC1048 1-131-992-91 CERAMIC CHIP 100000PF 35VC1050 1-162-974-11 CERAMIC CHIP 0.01uF 50VC1051 1-126-969-11 ELECT 220uF 20% 50VC1052 1-162-974-11 CERAMIC CHIP 0.01uF 50V
C1053 1-126-965-91 ELECT 22uF 20% 50VC1054 1-162-968-11 CERAMIC CHIP 0.0047uF 10% 50V
< CONNECTOR >
CN1021 1-784-774-11 CONNECTOR, FFC 13P
< DIODE >
D1021 8-719-058-03 DIODE SEL5423E-TP15 (n N)D1022 8-719-059-18 DIODE RD6.2FM-T1D1023 8-719-988-61 DIODE 1SS355TE-17D1024 8-719-988-61 DIODE 1SS355TE-17D1025 8-719-988-61 DIODE 1SS355TE-17
D1026 8-719-988-61 DIODE 1SS355TE-17
< FILTER >
FL1020 1-518-979-11 INDICATOR TUBE, FLUORESCENT
< IC >
IC1020 6-705-745-01 IC M66005-0131AHPRB0T
MOTOR PANEL
62
HCD-CPX22/NXM3
Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks
< COIL >
L1021 1-410-671-31 INDUCTOR 47uH
< TRANSISTOR >
Q1021 8-729-120-28 TRANSISTOR 2SC1623-L5L6Q1022 8-729-120-28 TRANSISTOR 2SC1623-L5L6Q1023 8-729-120-28 TRANSISTOR 2SC1623-L5L6Q1024 6-550-065-01 TRANSISTOR CPH5504-TL-EQ1026 8-729-027-43 TRANSISTOR DTC114EKA-T146
< RESISTOR >
R1020 1-216-809-11 METAL CHIP 100 5% 1/10WR1021 1-216-821-11 METAL CHIP 1K 5% 1/10WR1022 1-216-809-11 METAL CHIP 100 5% 1/10WR1023 1-216-809-11 METAL CHIP 100 5% 1/10WR1024 1-216-821-11 METAL CHIP 1K 5% 1/10W
R1025 1-216-833-11 METAL CHIP 10K 5% 1/10WR1026 1-216-813-11 METAL CHIP 220 5% 1/10WR1027 1-216-815-11 METAL CHIP 330 5% 1/10WR1028 1-216-817-11 METAL CHIP 470 5% 1/10WR1029 1-216-819-11 METAL CHIP 680 5% 1/10W
R1030 1-216-821-11 METAL CHIP 1K 5% 1/10WR1031 1-216-823-11 METAL CHIP 1.5K 5% 1/10WR1032 1-216-864-11 SHORT CHIP 0R1033 1-216-825-11 METAL CHIP 2.2K 5% 1/10WR1034 1-216-829-11 METAL CHIP 4.7K 5% 1/10W
R1035 1-216-833-11 METAL CHIP 10K 5% 1/10WR1036 1-216-823-11 METAL CHIP 1.5K 5% 1/10WR1037 1-216-825-11 METAL CHIP 2.2K 5% 1/10WR1038 1-216-829-11 METAL CHIP 4.7K 5% 1/10WR1039 1-216-833-11 METAL CHIP 10K 5% 1/10W
R1040 1-216-839-11 METAL CHIP 33K 5% 1/10WR1041 1-216-845-11 METAL CHIP 100K 5% 1/10WR1042 1-216-845-11 METAL CHIP 100K 5% 1/10WR1043 1-216-845-11 METAL CHIP 100K 5% 1/10WR1045 1-216-827-11 METAL CHIP 3.3K 5% 1/10W
R1046 1-216-833-11 METAL CHIP 10K 5% 1/10WR1051 1-216-809-11 METAL CHIP 100 5% 1/10WR1052 1-216-809-11 METAL CHIP 100 5% 1/10WR1100 1-216-833-11 METAL CHIP 10K 5% 1/10WR1101 1-216-833-11 METAL CHIP 10K 5% 1/10W
R1102 1-216-833-11 METAL CHIP 10K 5% 1/10W
< SWITCH >
S1021 1-762-875-21 SWITCH, KEYBOARD (CD)S1022 1-762-875-21 SWITCH, KEYBOARD (TUNER/BAND)S1023 1-762-875-21 SWITCH, KEYBOARD (TAPE A/B)S1024 1-762-875-21 SWITCH, KEYBOARD (VIDEO(MD))S1025 1-762-875-21 SWITCH, KEYBOARD (DIMMER)
S1026 1-762-875-21 SWITCH, KEYBOARD (CD SYNC)S1027 1-762-875-21 SWITCH, KEYBOARD (z /START)S1028 1-762-875-21 SWITCH, KEYBOARD (DISPLAY)S1029 1-762-875-21 SWITCH, KEYBOARD (n N)S1030 1-762-875-21 SWITCH, KEYBOARD (CD Z)
S1031 1-762-875-21 SWITCH, KEYBOARD (X)S1032 1-762-875-21 SWITCH, KEYBOARD (B> TUNING +)
S1033 1-762-875-21 SWITCH, KEYBOARD (.b TUNING -)S1034 1-762-875-21 SWITCH, KEYBOARD (ALBUM +)S1035 1-762-875-21 SWITCH, KEYBOARD (ALBUM -)
S1036 1-762-875-21 SWITCH, KEYBOARD (x)
< TRANSFORMER >
T801 1-443-389-11 TRANSFORMER, DC-DC CONVERTER************************************************************
A-4750-232-A RELAY BOARD, COMPLETE*********************
< CAPACITOR >
C701 1-126-786-11 ELECT 47uF 20% 16VC702 1-126-791-11 ELECT 10uF 20% 35VC761 1-162-306-11 CERAMIC 0.01uF 20% 16VC762 1-162-306-11 CERAMIC 0.01uF 20% 16V
< CONNECTOR >
CN701 1-779-558-21 CONNECTOR, FFC (LIF (NON-ZIF)) 21P
< DIODE >
D701 8-719-921-40 DIODE MTZJ-4.7CD711 8-719-982-10 DIODE MTZJ-4.3A
< IC >
IC701 8-759-598-69 IC BA6956ANIC711 8-759-598-69 IC BA6956AN
< TRANSISTOR >
Q751 8-729-119-78 TRANSISTOR 2SC2785-HFE
< RESISTOR >
R701 1-249-415-11 CARBON 680 5% 1/4WR702 1-247-807-31 CARBON 100 5% 1/4WR711 1-249-415-11 CARBON 680 5% 1/4WR712 1-247-807-31 CARBON 100 5% 1/4WR751 1-247-806-11 CARBON 91 5% 1/4W
R752 1-249-429-11 CARBON 10K 5% 1/4WR753 1-249-429-11 CARBON 10K 5% 1/4WR754 1-249-430-11 CARBON 12K 5% 1/4WR755 1-249-429-11 CARBON 10K 5% 1/4W
************************************************************
SENSOR BOARD************
< IC >
IC751 8-759-989-76 IC RPR-359F************************************************************
A-4750-863-A S-MASTER BOARD, COMPLETE**********************
< CAPACITOR >
C700 1-104-658-91 ELECT 100uF 20% 10VC701 1-126-960-11 ELECT 1uF 20% 50V
RELAYPANEL SENSOR S-MASTER
63
HCD-CPX22/NXM3
Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks
C702 1-136-850-11 MYLAR 0.1uF 5% 63VC703 1-104-658-91 ELECT 100uF 20% 10VC704 1-164-156-11 CERAMIC CHIP 0.1uF 25V
C706 1-164-346-11 CERAMIC CHIP 1uF 16VC708 1-164-346-11 CERAMIC CHIP 1uF 16VC709 1-164-156-11 CERAMIC CHIP 0.1uF 25VC710 1-162-923-11 CERAMIC CHIP 47PF 5% 50VC712 1-164-346-11 CERAMIC CHIP 1uF 16V
C713 1-163-078-11 CERAMIC CHIP 0.033uF 10% 25VC714 1-115-340-11 CERAMIC CHIP 0.22uF 10% 25VC715 1-115-340-11 CERAMIC CHIP 0.22uF 10% 25VC716 1-115-340-11 CERAMIC CHIP 0.22uF 10% 25VC717 1-115-340-11 CERAMIC CHIP 0.22uF 10% 25V
C718 1-163-078-11 CERAMIC CHIP 0.033uF 10% 25VC719 1-100-924-21 CAP, ELECTC720 1-136-177-00 FILM 1uF 5% 50VC721 1-125-898-91 CERAMIC CHIP 0.22uF 10% 50VC722 1-162-966-11 CERAMIC CHIP 0.0022uF 10% 50V
C723 1-162-966-11 CERAMIC CHIP 0.0022uF 10% 50VC724 1-162-966-11 CERAMIC CHIP 0.0022uF 10% 50VC725 1-162-966-11 CERAMIC CHIP 0.0022uF 10% 50VC726 1-164-505-11 CERAMIC CHIP 2.2uF 16VC727 1-125-898-91 CERAMIC CHIP 0.22uF 10% 50V
C728 1-136-177-00 FILM 1uF 5% 50VC729 1-164-156-11 CERAMIC CHIP 0.1uF 25VC730 1-164-156-11 CERAMIC CHIP 0.1uF 25VC731 1-104-658-91 ELECT 100uF 20% 10VC732 1-164-156-11 CERAMIC CHIP 0.1uF 25V
C733 1-164-156-11 CERAMIC CHIP 0.1uF 25VC734 1-164-156-11 CERAMIC CHIP 0.1uF 25VC735 1-126-964-11 ELECT 10uF 20% 50VC736 1-126-963-11 ELECT 4.7uF 20% 50VC737 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V
C738 1-162-915-11 CERAMIC CHIP 10PF 0.5PF 50VC739 1-162-915-11 CERAMIC CHIP 10PF 0.5PF 50VC741 1-126-965-91 ELECT 22uF 20% 50VC745 1-164-156-11 CERAMIC CHIP 0.1uF 25VC746 1-164-156-11 CERAMIC CHIP 0.1uF 25V
C747 1-104-658-91 ELECT 100uF 20% 10VC748 1-126-964-11 ELECT 10uF 20% 50VC749 1-164-156-11 CERAMIC CHIP 0.1uF 25VC750 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25VC751 1-126-960-11 ELECT 1uF 20% 50V
C752 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16VC753 1-104-658-91 ELECT 100uF 20% 10VC754 1-164-156-11 CERAMIC CHIP 0.1uF 25VC756 1-164-346-11 CERAMIC CHIP 1uF 16VC757 1-162-923-11 CERAMIC CHIP 47PF 5% 50V
C758 1-164-346-11 CERAMIC CHIP 1uF 16VC759 1-164-156-11 CERAMIC CHIP 0.1uF 25VC762 1-164-346-11 CERAMIC CHIP 1uF 16VC763 1-163-078-11 CERAMIC CHIP 0.033uF 10% 25VC764 1-115-340-11 CERAMIC CHIP 0.22uF 10% 25V
C765 1-115-340-11 CERAMIC CHIP 0.22uF 10% 25VC766 1-115-340-11 CERAMIC CHIP 0.22uF 10% 25VC767 1-115-340-11 CERAMIC CHIP 0.22uF 10% 25VC768 1-163-078-11 CERAMIC CHIP 0.033uF 10% 25VC769 1-100-924-21 CAP, ELECT 2200uF 35V
C770 1-136-177-00 FILM 1uF 5% 50VC771 1-125-898-91 CERAMIC CHIP 0.22uF 10% 50VC772 1-162-966-11 CERAMIC CHIP 0.0022uF 10% 50VC773 1-162-966-11 CERAMIC CHIP 0.0022uF 10% 50VC774 1-162-966-11 CERAMIC CHIP 0.0022uF 10% 50V
C775 1-162-966-11 CERAMIC CHIP 0.0022uF 10% 50VC776 1-125-898-91 CERAMIC CHIP 0.22uF 10% 50VC777 1-136-177-00 FILM 1uF 5% 50VC778 1-164-505-11 CERAMIC CHIP 2.2uF 16VC779 1-164-156-11 CERAMIC CHIP 0.1uF 25V
C780 1-164-156-11 CERAMIC CHIP 0.1uF 25VC781 1-164-156-11 CERAMIC CHIP 0.1uF 25VC782 1-164-156-11 CERAMIC CHIP 0.1uF 25VC783 1-162-915-11 CERAMIC CHIP 10PF 0.5PF 50VC784 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V
C785 1-162-910-11 CERAMIC CHIP 5PF 0.25PF 50VC786 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25VC787 1-164-156-11 CERAMIC CHIP 0.1uF 25VC788 1-164-156-11 CERAMIC CHIP 0.1uF 25VC790 1-104-658-91 ELECT 100uF 20% 10V
C791 1-136-850-11 MYLAR 0.1uF 5% 63VC792 1-126-935-11 ELECT 470uF 20% 16VC794 1-164-346-11 CERAMIC CHIP 1uF 16VC795 1-164-156-11 CERAMIC CHIP 0.1uF 25VC797 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
C798 1-104-658-91 ELECT 100uF 20% 10VC799 1-164-156-11 CERAMIC CHIP 0.1uF 25VC800 1-164-156-11 CERAMIC CHIP 0.1uF 25VC801 1-164-156-11 CERAMIC CHIP 0.1uF 25VC802 1-164-156-11 CERAMIC CHIP 0.1uF 25V
C803 1-126-956-91 ELECT 0.1uF 20% 50VC804 1-104-658-91 ELECT 100uF 20% 10VC805 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16VC806 1-164-156-11 CERAMIC CHIP 0.1uF 25VC821 1-216-864-11 SHORT CHIP 0
C822 1-216-864-11 SHORT CHIP 0C823 1-216-864-11 SHORT CHIP 0C824 1-216-864-11 SHORT CHIP 0C825 1-216-864-11 SHORT CHIP 0C826 1-216-864-11 SHORT CHIP 0
C827 1-216-864-11 SHORT CHIP 0C828 1-216-864-11 SHORT CHIP 0C829 1-216-864-11 SHORT CHIP 0C830 1-216-864-11 SHORT CHIP 0
< CONNECTOR >
CN700 1-784-780-11 CONNECTOR, FFC 19P* CN701 1-564-511-11 PLUG, CONNECTOR 8P
CN702 1-564-507-11 PLUG, CONNECTOR 4P
< DIODE >
D701 8-719-988-61 DIODE 1SS355TE-17D702 8-719-988-61 DIODE 1SS355TE-17D703 8-719-988-61 DIODE 1SS355TE-17D704 8-719-988-61 DIODE 1SS355TE-17D705 6-500-260-01 DIODE P6SMB39AT3
D706 6-500-260-01 DIODE P6SMB39AT3D707 8-719-988-61 DIODE 1SS355TE-17
S-MASTER
64
HCD-CPX22/NXM3
Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks
D708 8-719-988-61 DIODE 1SS355TE-17D709 8-719-988-61 DIODE 1SS355TE-17D710 8-719-988-61 DIODE 1SS355TE-17
D711 8-719-988-61 DIODE 1SS355TE-17D712 8-719-988-61 DIODE 1SS355TE-17D755 6-500-260-01 DIODE P6SMB39AT3D756 6-500-260-01 DIODE P6SMB39AT3
< EARTH TERMINAL >
EP701 1-537-738-21 TERMINAL, GROUNDEP702 1-537-738-21 TERMINAL, GROUND
< FERRITE BEAD >
FB702 1-216-864-11 SHORT CHIP 0
< FILTER >
FL702 1-234-177-21 FILTER, CHIP EMIFL703 1-234-177-21 FILTER, CHIP EMIFL704 1-234-177-21 FILTER, CHIP EMIFL706 1-234-177-21 FILTER, CHIP EMI
< IC >
IC701 6-701-834-01 IC PCM1802DBRIC703 8-759-387-77 IC TC7WU04F (TE12R)IC704 6-700-263-01 IC NJM2870F18 (TE2)IC705 6-705-979-01 IC CXD9788ARIC706 8-759-583-47 IC uPC2933T-E2
IC707 6-705-695-01 IC CXD9775MIC708 6-705-695-01 IC CXD9775MIC709 6-701-189-01 IC MC74VHC1GU04DFT1IC710 8-759-473-95 IC uPC2905T-E1
< COIL >
L701 1-412-951-11 INDUCTOR 10uHL702 1-412-951-11 INDUCTOR 10uHL703 1-412-951-11 INDUCTOR 10uHL704 1-216-295-91 SHORT CHIP 0L705 1-412-939-11 INDUCTOR 1uH
L708 1-456-813-11 COIL, AIR-COREL709 1-456-813-11 COIL, AIR-COREL710 1-456-680-11 COIL, CHOKE 10UFL711 1-456-680-11 COIL, CHOKE 10UFL712 1-412-951-11 INDUCTOR 10uH
L713 1-216-295-91 SHORT CHIP 0L714 1-216-295-91 SHORT CHIP 0L715 1-216-295-91 SHORT CHIP 0L716 1-216-295-91 SHORT CHIP 0L758 1-456-813-11 COIL, AIR-CORE
L759 1-456-813-11 COIL, AIR-COREL760 1-456-680-11 COIL, CHOKE 10UFL761 1-456-680-11 COIL, CHOKE 10UF
< TRANSISTOR >
Q701 8-729-120-28 TRANSISTOR 2SC1623-L5L6Q702 8-729-602-36 TRANSISTOR 2SA1602-FQ703 8-729-602-36 TRANSISTOR 2SA1602-FQ752 8-729-602-36 TRANSISTOR 2SA1602-FQ753 8-729-602-36 TRANSISTOR 2SA1602-F
< RESISTOR >
R701 1-216-864-11 SHORT CHIP 0R704 1-216-864-11 SHORT CHIP 0R706 1-216-809-11 METAL CHIP 100 5% 1/10WR707 1-216-864-11 SHORT CHIP 0R708 1-216-864-11 SHORT CHIP 0
R709 1-216-864-11 SHORT CHIP 0R710 1-216-809-11 METAL CHIP 100 5% 1/10WR711 1-216-809-11 METAL CHIP 100 5% 1/10WR712 1-216-809-11 METAL CHIP 100 5% 1/10WR713 1-216-837-11 METAL CHIP 22K 5% 1/10W
R714 1-216-818-11 METAL CHIP 560 5% 1/10WR716 1-216-829-11 METAL CHIP 4.7K 5% 1/10WR717 1-216-864-11 SHORT CHIP 0R718 1-216-829-11 METAL CHIP 4.7K 5% 1/10WR719 1-220-942-11 METAL CHIP 3.3 1% 1/4W
R720 1-220-942-11 METAL CHIP 3.3 1% 1/4WR721 1-216-829-11 METAL CHIP 4.7K 5% 1/10WR722 1-216-864-11 SHORT CHIP 0R723 1-216-841-11 METAL CHIP 47K 5% 1/10WR724 1-216-302-00 RES-CHIP 2.7 5% 1/10W
R725 1-216-302-00 RES-CHIP 2.7 5% 1/10WR726 1-216-845-11 METAL CHIP 100K 5% 1/10WR727 1-216-845-11 METAL CHIP 100K 5% 1/10WR728 1-216-845-11 METAL CHIP 100K 5% 1/10WR729 1-216-821-11 METAL CHIP 1K 5% 1/10W
R730 1-216-809-11 METAL CHIP 100 5% 1/10WR731 1-216-809-11 METAL CHIP 100 5% 1/10WR732 1-216-809-11 METAL CHIP 100 5% 1/10WR735 1-216-864-11 SHORT CHIP 0R736 1-216-857-11 METAL CHIP 1M 5% 1/10W
R737 1-216-821-11 METAL CHIP 1K 5% 1/10WR739 1-216-864-11 SHORT CHIP 0R741 1-216-809-11 METAL CHIP 100 5% 1/10WR742 1-216-833-11 METAL CHIP 10K 5% 1/10WR743 1-216-809-11 METAL CHIP 100 5% 1/10W
R744 1-216-864-11 SHORT CHIP 0R745 1-216-809-11 METAL CHIP 100 5% 1/10WR746 1-216-809-11 METAL CHIP 100 5% 1/10WR747 1-216-809-11 METAL CHIP 100 5% 1/10WR748 1-216-841-11 METAL CHIP 47K 5% 1/10W
R749 1-216-864-11 SHORT CHIP 0R750 1-216-845-11 METAL CHIP 100K 5% 1/10WR751 1-216-864-11 SHORT CHIP 0R752 1-216-837-11 METAL CHIP 22K 5% 1/10WR754 1-216-818-11 METAL CHIP 560 5% 1/10W
R756 1-216-809-11 METAL CHIP 100 5% 1/10WR757 1-216-864-11 SHORT CHIP 0R758 1-216-864-11 SHORT CHIP 0R759 1-216-864-11 SHORT CHIP 0R760 1-216-809-11 METAL CHIP 100 5% 1/10W
R761 1-216-809-11 METAL CHIP 100 5% 1/10WR762 1-216-809-11 METAL CHIP 100 5% 1/10WR764 1-216-864-11 SHORT CHIP 0R766 1-216-829-11 METAL CHIP 4.7K 5% 1/10WR767 1-216-864-11 SHORT CHIP 0
S-MASTER
65
HCD-CPX22/NXM3
Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks
SP OUT
R768 1-216-829-11 METAL CHIP 4.7K 5% 1/10WR769 1-220-942-11 METAL CHIP 3.3 1% 1/4WR770 1-220-942-11 METAL CHIP 3.3 1% 1/4WR771 1-216-829-11 METAL CHIP 4.7K 5% 1/10WR772 1-216-864-11 SHORT CHIP 0
R773 1-216-841-11 METAL CHIP 47K 5% 1/10WR774 1-216-302-00 RES-CHIP 2.7 5% 1/10WR775 1-216-302-00 RES-CHIP 2.7 5% 1/10WR776 1-216-845-11 METAL CHIP 100K 5% 1/10WR777 1-216-845-11 METAL CHIP 100K 5% 1/10W
R778 1-216-845-11 METAL CHIP 100K 5% 1/10WR779 1-216-864-11 SHORT CHIP 0R781 1-216-809-11 METAL CHIP 100 5% 1/10WR782 1-216-857-11 METAL CHIP 1M 5% 1/10WR783 1-216-864-11 SHORT CHIP 0
R784 1-216-809-11 METAL CHIP 100 5% 1/10WR785 1-216-809-11 METAL CHIP 100 5% 1/10WR786 1-216-809-11 METAL CHIP 100 5% 1/10WR787 1-216-809-11 METAL CHIP 100 5% 1/10WR788 1-216-809-11 METAL CHIP 100 5% 1/10W
R789 1-216-809-11 METAL CHIP 100 5% 1/10WR790 1-216-809-11 METAL CHIP 100 5% 1/10WR792 1-216-864-11 SHORT CHIP 0R793 1-216-845-11 METAL CHIP 100K 5% 1/10WR795 1-216-864-11 SHORT CHIP 0
< VIBRATOR >
X701 1-795-843-11 VIBRATOR, CRYSTAL (12.288MHz)X702 1-795-660-21 QUARTZ CRYSTAL UNIT (49.152MHz)
************************************************************
SP OUT BOARD************
< CAPACITOR >
C591 1-131-992-91 CERAMIC CHIP 100000PF 35V(AEP, UK, EA, RU)
C592 1-131-992-91 CERAMIC CHIP 100000PF 35V(AEP, UK, EA, RU)
C594 1-131-992-91 CERAMIC CHIP 100000PF 35V(AEP, UK, EA, RU)
C595 1-131-992-91 CERAMIC CHIP 100000PF 35V(AEP, UK, EA, RU)
C596 1-131-992-91 CERAMIC CHIP 100000PF 35V(AEP, UK, EA, RU)
C597 1-131-992-91 CERAMIC CHIP 100000PF 35V(AEP, UK, EA, RU)
C598 1-131-992-91 CERAMIC CHIP 100000PF 35V(AEP, UK, EA, RU)
C599 1-131-992-91 CERAMIC CHIP 100000PF 35V(AEP, UK, EA, RU)
< CONNECTOR >
CN510 1-564-507-11 PLUG, CONNECTOR 4P
< EARTH TERMINAL >
EP505 1-537-738-21 TERMINAL, GROUND
< COIL >
L590 1-420-872-52 COIL, AIR-CORE (AEP, UK, EA, RU)L591 1-420-872-52 COIL, AIR-CORE (AEP, UK, EA, RU)L592 1-420-872-52 COIL, AIR-CORE (AEP, UK, EA, RU)L593 1-420-872-52 COIL, AIR-CORE (AEP, UK, EA, RU)
< RESISTOR >
R592 1-249-625-31 CARBON 10 5% 1/2W(AEP, UK, EA, RU)
R593 1-249-625-31 CARBON 10 5% 1/2W(AEP, UK, EA, RU)
R594 1-249-625-31 CARBON 10 5% 1/2W(AEP, UK, EA, RU)
R595 1-249-625-31 CARBON 10 5% 1/2W(AEP, UK, EA, RU)
R596 1-249-625-31 CARBON 10 5% 1/2W(AEP, UK, EA, RU)
R597 1-249-625-31 CARBON 10 5% 1/2W(AEP, UK, EA, RU)
R598 1-249-625-31 CARBON 10 5% 1/2W(AEP, UK, EA, RU)
R599 1-249-625-31 CARBON 10 5% 1/2W(AEP, UK, EA, RU)
< TERMINAL >
TM504 1-537-114-21 TERMINAL BOARD (SPEAKER)************************************************************
SW (1) BOARD***********
< SWITCH >
S721 1-786-084-11 SWITCH, DETECTION (MAIN TRAY IN/OUT)************************************************************
SW (2) BOARD***********
< SWITCH >
S731 1-786-382-11 SWITCH, PUSH (1 KEY) (SUB TRAY IN)************************************************************
A-4750-851-A VOL BOARD, COMPLETE*******************
< CAPACITOR >
C1007 1-164-156-11 CERAMIC CHIP 0.1uF 25VC1008 1-164-156-11 CERAMIC CHIP 0.1uF 25VC1013 1-126-947-11 ELECT 47uF 20% 35V
< CONNECTOR >
CN1050 1-784-776-11 CONNECTOR, FFC 15PCN1051 1-784-766-11 CONNECTOR, FFC 5P
< DIODE >
D1050 8-719-071-44 DIODE SELS5223C-TP15 (^/1)D1051 8-719-988-61 DIODE 1SS355TE-17
S-MASTER SW (1) SW (2) VOL
66
HCD-GN880
The components identified bymark 0 or dotted line with mark0 are critical for safety.Replace only with part numberspecified.
< IC >
IC1050 6-600-349-31 IC NJL24H400A
< TRANSISTOR >
Q1041 8-729-027-43 TRANSISTOR DTC114EKA-T146
< RESISTOR >
R1048 1-216-864-11 SHORT CHIP 0R1049 1-216-821-11 METAL CHIP 1K 5% 1/10WR1050 1-216-823-11 METAL CHIP 1.5K 5% 1/10WR1059 1-216-805-11 METAL CHIP 47 5% 1/10WR1090 1-216-821-11 METAL CHIP 1K 5% 1/10W
R1091 1-216-821-11 METAL CHIP 1K 5% 1/10WR1092 1-216-821-11 METAL CHIP 1K 5% 1/10WR1093 1-216-821-11 METAL CHIP 1K 5% 1/10WR1094 1-216-821-11 METAL CHIP 1K 5% 1/10WR1095 1-216-821-11 METAL CHIP 1K 5% 1/10W
< SWITCH >
S1042 1-762-875-21 SWITCH, KEYBOARD (^/1)S1043 1-762-875-21 SWITCH, KEYBOARD (DSGX)S1050 1-786-418-11 SWITCH, ROTARY (ENCODER) (BASS)S1051 1-786-418-11 SWITCH, ROTARY (ENCODER) (TREBLE)S1052 1-418-725-51 ENCODER, ROTARY (12 TYPE) (VOLUME)
************************************************************
MISCELLANEOUS*************
3 1-769-972-11 WIRE (FLAT TYPE) (13 CORE)4 1-765-332-11 WIRE (FLAT TYPE) (15 CORE)5 1-769-869-11 WIRE (FLAT TYPE) (5 CORE)6 1-769-939-11 WIRE (FLAT TYPE) (11 CORE) (EXCEPT AEP, UK)6 1-773-003-11 WIRE (FLAT TYPE) (15 CORE) (AEP, UK)
11 1-693-603-31 TUNER (FM/AM) (E3, E51, EA)11 1-693-604-11 TUNER (FM/AM) (AEP, UK)11 1-693-623-31 TUNER (FM/AM) (US)11 1-693-654-11 TUNER (FM/AM) (RU)59 1-796-880-11 DECK, MECHANISM
0102 1-468-813-11 REGULATOR, SWITCHING (AEP, UK, RU)0102 1-468-819-11 REGULATOR, SWITCHING (US)0102 1-468-821-11 REGULATOR, SWITCHING (E3, E51, EA)0103 1-775-786-21 CORD, POWER (UK, EA)0103 1-777-071-53 CORD, POWER (AEP, E51, RU)
0103 1-783-820-11 CORD, POWER (US)0103 1-827-226-11 CORD, POWER (E3)
162 1-471-035-11 MAGNET ASSY256 1-827-992-11 WIRE (FLAT TYPE) (16 CORE)
0259 8-820-244-01 OPTICAL PICK-UP (KSM-215DCP/C2NP)
M761 A-4713-174-A MOTOR (81) ASSY (LD/ST MOTOR)M762 A-4713-174-A MOTOR (81) ASSY (BU U/D MOTOR)S771 1-478-552-11 ENCODER, ROTARY (MD)S781 1-478-551-11 ENCODER, ROTARY (ST U/D)
Ref. No. Part No. Description Remarks
VOL