HCD-LS1 - SERVICE MANUAL

SERVICE MANUAL

COMPACT DISC RECEIVER

SPECIFICATIONS

HCD-LS1US Model

Canadian ModelAEP Model

UK ModelE Model

HCD-LS1 is the Amplifier, CD player andTuner section in CMT-LS1.

– Continued on next page –

CD player sectionSystem Compact disc and digital audio

systemLaser Semiconductor laser (λ=780 nm)

Emission duration: continuousLaser output Max. 44.6 µW*

*This output is the value measuredat a distance of 200 mm from theobjective lens surface on theOptical Pick-up Block with 7 mmaperture.

Frequency response 20 Hz – 20,000 Hz (±3.0 dB)

Amplifier section

For the U.S. model

AUDIO POWER SPECIFICATIONSPOWER OUTPUT AND TOTAL HARMONICDISTORTION:With 4 ohm loads both channels driven, from 120 –10,000 Hz; rated 10 watts per channel minimumRMS power, with no more than 10% totalharmonic distortion from 250 milliwatts to ratedoutput.

North American model:Continuous RMS power output (Reference)

16 + 16 watts(4 ohms at 1 kHz, 10% THD)

European model:DIN power output (Rated) 11 + 11 watts

(4 ohms at 1 kHz, DIN)Continuous RMS power output (Reference)

16 + 16 watts(4 ohms at 1 kHz, 10% THD)

Other models:DIN power output (Rated) 11 + 11 watts

(4 ohms at 1 kHz, DIN, 240 V)11 + 11 watts(4 ohms at 1 kHz, DIN, 220 V)

Continuous RMS power output (Reference)16 + 16 watts(4 ohms at 1 kHz, 10% THD,240 V)16 + 16 watts(4 ohms at 1 kHz, 10% THD,220 V)

Inputs TAPE IN (stereo mini jack):voltage 250 mV, impedance47 kilohms

Outputs TAPE OUT (stereo mini jack):1Vrms at CD Full Bit Play,impedance 1 kilohmCD OUT: OpticalPHONES (stereo mini jack):accepts headphones of 8 ohms ormoreSPEAKER: speaker system4 ohms

Model Name Using Similar Mechanism NEW

CD Mechanism Type HG-1

Optical Pick-up Name KSS-540A

9-929-063-12 Sony Corporation2002K0500-1 Home Audio Company

C 2002.11 Published by Sony Engineering Corporation

Ver 1.1 2002.11

2

TABLE OF CONTENTS

1. SERVICING NOTES ............................................... 3

2. GENERAL ................................................................... 5

3. DISASSEMBLY ......................................................... 7

4. ELECTRICAL ADJUSTMENT ............................ 19

5. DIAGRAMS5-1. Note for Printed Wiring Boards and

Schematic Diagrams ....................................................... 215-2. Printed Wiring Board – CD Section – ........................... 225-3. Schematic Diagram – CD Section (1/3) – ..................... 235-4. Schematic Diagram – CD Section (2/3) – ..................... 245-5. Schematic Diagram – CD Section (3/3) – ..................... 255-6. Printed Wiring Board – Main Section – ........................ 265-7. Schematic Diagram

– MAIN Section – ........................................................... 275-8. Printed Wiring Boards

– AMP/RELAY/JACK Board – ...................................... 285-9. Schematic Diagram

– AMP/RELAY/JACK Board – ...................................... 295-10. Printed Wiring Boards – Panel Section (1/2) – ............. 305-11. Schematic Diagram – Panel Section (1/2) – .................. 315-12. Printed Wiring Boards – Panel Section (2/2) – ............. 325-13. Schematic Diagram – Panel Section (2/2) – .................. 325-14. Printed Wiring Boards

– POWER SUPPLY Section – ....................................... 345-15. Schematic Diagram – POWER SUPPLY Section – ....... 35

6. EXPLODED VIEWS ................................................ 37

7. ELECTRICAL PARTS LIST ............................... 43

ATTENTION AU COMPOSANT AYANT RAPPORTÀ LA SÉCURITÉ!

LES COMPOSANTS IDENTIFIÉS PAR UNE MARQUE 0SUR LES DIAGRAMMES SCHÉMATIQUES ET LA LISTEDES PIÈCES SONT CRITIQUES POUR LA SÉCURITÉDE FONCTIONNEMENT. NE REMPLACER CES COM-POSANTS QUE PAR DES PIÈCES SONY DONT LESNUMÉROS SONT DONNÉS DANS CE MANUEL OUDANS LES SUPPLÉMENTS PUBLIÉS PAR SONY.

SAFETY-RELATED COMPONENT WARNING!!

COMPONENTS IDENTIFIED BY MARK 0 OR DOTTEDLINE WITH MARK 0 ON THE SCHEMATIC DIAGRAMSAND IN THE PARTS LIST ARE CRITICAL TO SAFEOPERATION. REPLACE THESE COMPONENTS WITHSONY PARTS WHOSE PART NUMBERS APPEAR ASSHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUB-LISHED BY SONY.

Desktop standDimensions (w/h/d) 184 × 218 × 140 mmMass Approx. 0.5 kg

Wall hanging adapterDimensions (w/h/d) 180 × 220 × 39 mmMass Approx. 0.5 kg

Wall hanging bracketDimensions (w/h/d) 180 × 220 × 12 mmMass Approx. 0.4 kg

GeneralPower requirementsNorth American model: 120 V AC, 60 HzEuropean model: 230 V AC, 50/60 HzOther models: 220 – 240 V AC, 50/60 HzPower consumption 25 WDimensions 192 × 295 × 150 mm

(w/h/d, incl. projecting parts,controls and desktop stand)

Mass Approx. 4.0 (with Desktopstand) kg

Supplied accessories Remote commander (1)AM loop antenna (1)FM wire antenna (1)Desktop stand (1)Wall hanging adapter (1)Wall hanging bracket (1)Screws for stand or adapterM4 × 14 (4)Dust caps (3)

Designs and specifications are subject to changewithout notice.

Tuner sectionFM stereo, FM/AM superheterodyne tuner

FM tuner sectionTuning rangeNorth American model: 87.5 – 108.0 MHz (100 kHz step)Other models: 87.5 – 108.0 MHz (50 kHz step)Antenna FM lead antennaAntenna terminals 75 ohms unbalancedIntermediate frequency 10.7 MHz

AM tuner sectionTuning rangeNorth American model: 530 – 1,710 kHz

(with the interval set at 10 kHz)531 – 1,710 kHz(with the interval set at 9 kHz)

European model: 531 – 1,602 kHz(with the interval set at 9 kHz)

Other models: 531 – 1,602 kHz(with the interval set at 9 kHz)530 – 1,710 kHz(with the interval set at 10 kHz)

Antenna AM loop antennaIntermediate frequency 450 kHz

3

SECTION 1SERVICING NOTES

The laser diode in the optical pick-up block may suffer electro-static break-down because of the potential difference generatedby the charged electrostatic load, etc. on clothing and the humanbody.During repair, pay attention to electrostatic break-down and alsouse the procedure in the printed matter which is included in therepair parts.The flexible board is easily damaged and should be handled withcare.

NOTES ON LASER DIODE EMISSION CHECKThe laser beam on this model is concentrated so as to be focusedon the disc reflective surface by the objective lens in the opticalpick-up block. Therefore, when checking the laser diode emis-sion, observe from more than 30 cm away from the objective lens.

Notes on chip component replacement• Never reuse a disconnected chip component.• Notice that the minus side of a tantalum capacitor may be dam-

aged by heat.

Flexible Circuit Board Repairing• Keep the temperature of the soldering iron around 270 ˚C dur-

ing repairing.• Do not touch the soldering iron on the same conductor of the

circuit board (within 3 times).• Be careful not to apply force on the conductor when soldering

or unsoldering.

NOTES ON HANDLING THE OPTICAL PICK-UPBLOCK OR BASE UNIT

SAFETY CHECK-OUTAfter correcting the original service problem, perform the follow-ing safety check before releasing the set to the customer:Check the antenna terminals, metal trim, “metallized” knobs,screws, and all other exposed metal parts for AC leakage.Check leakage as described below.

LEAKAGE TESTThe AC leakage from any exposed metal part to earth ground andfrom all exposed metal parts to any exposed metal part having areturn to chassis, must not exceed 0.5 mA (500 microamperes.).Leakage current can be measured by any one of three methods.1. A commercial leakage tester, such as the Simpson 229 or RCA

WT-540A. Follow the manufacturers’ instructions to use theseinstruments.

2. A battery-operated AC milliammeter. The Data Precision 245digital multimeter is suitable for this job.

3. Measuring the voltage drop across a resistor by means of aVOM or battery-operated AC voltmeter. The “limit” indica-tion is 0.75 V, so analog meters must have an accurate low-voltage scale. The Simpson 250 and Sanwa SH-63Trd are ex-amples of a passive VOM that is suitable. Nearly all batteryoperated digital multimeters that have a 2 V AC range are suit-able. (See Fig. A)

Fig. A. Using an AC voltmeter to check AC leakage.

1.5 kΩ0.15 µFACvoltmeter(0.75 V)

To Exposed MetalParts on Set

Earth Ground

This appliance is classified as a CLASS 1 LASER product.The CLASS 1 LASER PRODUCT MARKING is located onthe rear exterior.

CAUTIONUse of controls or adjustments or performance of proceduresother than those specified herein may result in hazardous ra-diation exposure.

4

DISC EJECTION IN EMERGENCY

In case of emergency, remove the discs inside the Mechanism Ass’y(CD Changer) as follows:(1) Disconnect the power of the Main Unit.(2) Remove the Mechanism Ass’y. Refer to item(3) Remove two top cover fastening screws at the rear of the

Mechanism Ass’y, and take off the Top Cover HS Ass’y. Referto Fig. A.

(4) Remove the left side adhesive label (Dust Seal EMA SL) onthe left side of the Mechanism Ass’y. Refer to Fig. A.Note: Carefully remove it since it is used again later.

(5) Turn the Emergency Gear SL up or down until the disc locksleeve SL is lowered as shown in Fig. B.Caution: Never use nail when turning the Emergency Gear

SL. Otherwise, the gear tooth may be broken.(6) Raise the front section of the Mechanism Ass’y as illustrated

in Fig. B. Then carefully spread the Loading L/R MF Ass’y sothat the disc drops into the Stocker.

(7) While keeping the Loading L/R MF Ass’y spread, remove thediscs.Note: When removing the discs, take care not to scrape them

against other parts, to prevent damage.(8) Replace the removed parts by reversing the above procedure.

Note: To prevent dust from entering the unit, reattach theadhesive label on the opening for the Emergency GearSL.

(9) Perform the mechanism initialization as follows to clear thedisc information stored in the Mechanism Ass’y.Press the DISC1 button while pressing the DISC5 button.Then, the Unit enters the CD Playback mode and mechanismInitialization operation begins and disc change operation starts.After that, the Unit enters Standby mode.

DISC1 + DISC5

Top Cover Fastening Screws

Label

Fig. A

Loading L MF Ass’y

Loading R MF Ass’y

Emergency Gear SL

Dust Seal EMA SL

Disc Lock Sleeve SL

– Up Position – – Down Position –

Fig. B

5

SECTION 2GENERAL

• LOCATION OF CONTROLS– Front View –

1 FUNCTION button

2 DISC 1 button and indicator





7 VOLUME + button

8 TUNER/BAND button

9 u button and indicator

q; x button

qa . m , TUNER - button

qs > M , TUNER + button

qd A button

qf VOLUME - button

1 AM ANTENNA terminals

2 FM ANTENNA jack

3 TAPE OUT jack

4 TAPE IN jack

5 PHONES jack

6 `/1 button

7 PANEL OPEN switch

8 PANEL OPEN/CLOSE switch

1 CD DIGITAL OUT (OPTICAL) connector

2 LEFT SPEAKER terminals

3 RIGHT SPEAKER terminals

– Top View –

– Rear View –

8 9 q; qa qs qd qf

1 2 3 4 56 7

54321

6 7 8

1

2

3

6

This section is extracted frominstruction manual.

Step 2: Setting the timeYou must set the time before you can use thetimer functions.

The clock is on a 24-hour system for the Europeanmodel, and a 12-hour system for other models.The 24 hour system model is used for illustrationpurposes.

Set the time before turning on the power.

–

+

– +

>1010/0

8 97

5 64

2 31

m M

–

+

x

. >

N X

12,32,3

1 Press CLOCK/TIMER SET while thepower is off.The hour indication flashes.

2 Press +/– to set the hour then pressENTER.The minute indication flashes.

3 Press +/– to set the minute then pressENTER.The clock starts.

To change the timeYou can change the preset time while the power ison.

1 Press CLOCK/TIMER SET.2 Press +/– repeatedly until “SET CLOCK”

appears then press ENTER.3 Repeat steps 2 and 3 of “Setting the time”.

Tips• If you have made a mistake, start again from step 1.• The built-in clock shows the time in the display

while the power is off.• The upper dot flashes for the first half of a minute

(0 to 29 seconds), and the lower dot flashes for thelast half of a minute (30 to 59 seconds).

7

SECTION 3DISASSEMBLY

Note: Follow the disassembly procedure in the numerical order given.

MAIN CASE SECTION

MECHANISM DECK (HG-1)

6 two claws

7 FFC (26core)(CN604)

5 two screws(BTP 3 × 10)


9 main case section


1 screw(B3 × 6)

2 bottom cover

3 belt

8 two connectors(PC501, 502)

5 mechanism deck (HG-1)

2 two lugs

1 four screws(BTP 3 × 10)

4 connector(CP503)

2 two lugs

3

DOOR MOTOR ASS’Y (M391) (Next Page)HOLDER MECHA, DUST SEAL EMA SL(Page 9)

8

DOOR MOTOR ASS’Y (M391)

MAIN BOARD

1 connector(CN391)

5 two screws(P2.6 × 3)

7 door motor ass’y(M391)

6 motor bracket

2 two screws(BTP3 × 8)

3 lug

4

1 FFC (15core)(CN101)

slide knob

4 Remove the MAIN board in the direction of the arrow.

2 five connectors(CN203, 301, 302, 303, 391)

3 two screws(PWH2.6 × 6)

2 two connectors(CN201, 204)

Note: On installation MAIN boardadjust the S391 and slide knob.

S391

9

(1) MODE-1EJECT, DISC LOAD state

(2) MODE-2STANDARD State (STOP state)

(3) MODE-3PLAY, DISC CHANGE state

When disassembling and reassembling the mechanism deck by any failure, the mechanism deck must be in (2) Standard state (STOP state) as shown below.• The mechanism deck (HG-1) has three modes. (Fig. A)

mecha UD sub cam SL

Traverse Mecha Down state

Traverse Mecha Up state

sus base X sub ass’y shaft

(Fig. A)

HOW TO ADJUST STOP STATE POSITION D lock sleeve SL

emergency gear SL

2 Rotate gradually the emergency gear SL in the up arrow direction up to the position where the D lock sleeve SL comes to the bottom.(To attain (2) standard state in Fig. A)

1 Rotate fully the emergency gear SL in the down arrow direction.

HOLDER MECHA, DUST SEAL EMA SL

PRECAUTIONS ON DISASSEMBLING AND REASSEMBLING MECHANISM DECK

1 four screws(B3 × 5)

2 holder mecha

3 dust seal EMA SL

Note:Carefully remove it sinceit is used again later.

1 four screws(B3 × 5)

2 holder mecha

10

TOP COVER HS ASS’Y, BOTTOM COVER MF ASS’Y, F PANEL ASS’Y R237

5 F panel ass’y R237


3 four screws(P2.6 × 5)


4 Remove bottom coverMF ass’y in the directionof arrow B.

B

2 Remove top cover HS ass’yin the direction of arrow A.

A

Mecha UD Sub SL

Emergency Gear SL

(Fig. B.1)

(Fig. B.2)

Note: 1. Before reassembling F Panel Ass’y R237be sure that the end of the Mecha UD SubCam SL on the right front does not protrudeas shown in (Fig. B.1). If it protrudes, move it backward as follows:1) Carefully remove the left side adhesive

label (Dust Seal EMA SL) on the left sideof the unit. refer to (Fig. B.2)

2) Turn the Emergency Gear SL with your finger tip in the direction of the arrow until the end of the Mecha UD Sub Cam SL is drawn inside the unit. (See Fig. B.2).When turning the Gear, DO NOT use nailas the gear tooth can be broken.

3) Reattach the adhesive label (Dust Seal EMASL).

Note: 2. Be sure that the claws of F Panel Ass’y R237 aresecurely inserted into each holes in Top Cover HS Ass’y and Bottom Cover MF ass’y.

11

MAIN R237 BOARD

INSTALLING THE MAIN R237 BOARD

2 screw(P2.6 × 4)

4 wire flexible board(CP102)

5 PCB FLEX mecha ass’y(CP103)

1 screw(P2.6 × 8)

6 pick-up flexible board(CP101)

Note: When disconnecting these felxible boards, do not open the MAIN R237 board wide toavoid damage to flexible boaards.

3

MAIN R237 board

Unsolder the shorting landson the pick-up flexible board.

Note: To allow easier installation of the MAIN R237 board, move the optical pick-up KSS-540A to the outermostposition, before removing the MAIN R237 board.

LOADING MF ASS’Y(Next Page)STC POS GEAR SL(Page 18)

12

LOADING MF ASS’Y

TRAVERSE MECHA ASS’Y

1 three screws(P2 × 2)

7 loading MF ass’y

2 two screws(2.6 × 3) 2 two screws

(2.6 × 3)

8 washer

9 loading linkSL ass’y

3 screw(P1.7 × 2.5)

5 ditch

5 ditch

6 While pushing lever inward, remove loading MF ass’y by lifting it upward.

lever

Note:Though the cam of the Mecha UD sub cam SL will be in (1) state in (Refer to page 9. Fig. A) when the loading MF Ass’y is assembled, set in (2) state in (Refer to page 9. Fig. A) usingthe emergency gear SL.

4

3 two damper screws3 two damper screws

4 traverse mecha ass’y

1 three screws(P2 × 2) 2 FR chassis SL ass’y

PCB FLEX MECHAASS’Y(Page 15)

13

MOTOR (SLED) (M1)

INSTALLING A MOTOR (SLED) (M1)

1 Remove two solders of the sled motor leads (M1).

5 first gear

Note:When first gear is removed, make sure to install a bland new gear.

6 motor (sled)(M1)

Note:Pay attention to the motor (sled) installing direction.

2 washer

3 second gear

4 two screws(P1.7 × 2.5)

0.1 mm

motor (sled) (M1)

first gear

(Fig. C)

Note: Press fit a new first gear so that the gap between the chassis surface and the bottom of first gear is 0.1mm as shown in Fig. C.

14

OPTICAL PICK-UP KSS-540A

INSTALLING A OPTICAL PICK-UP KSS-540A


6 optical pick-up KSS-540A

5 pick-up flexible board

2 screw(P2.6 × 3)

3 two SH lock plate SLs

2 screw(P2.6 × 3)

3 two SH lock plate SLs

4 PU guide shaft SL

Note: Before disconnecting the pick-up flexible board from the optical pick-up KSS-540A, short the laser diode shorting lands on the bottom of the optical pick-up KSS-540A.Refer to Fig. D.

pick-up flexible board

1. Connect the pick-up flexible board to the optical pick-up KSS-540A.2. Open the laser diode shorting lands on the bottom of the optical pick-up KSS-540A.

Note:Use the soldering iron whose metal part is grounded or a ceramic soldering iron.

(Fig. D)

15

2 two screws(P2 × 2)

1 Remove two solders ofthe STC motor SL ass’yflexible board (M3).

4 screw(P2 × 2)

5 PCB FLEX mecha ass’y

3 Remove four solders of the loading motor leads (M4) and up/down motor leads (M5).

PU G PLATE H SL

PCB FLEX MECHA ASS’Y

3 screw (2 × 4)

2 screw (2 × 4)

1 screw (2 × 4)

4 PU G plate H SL

Note:Assemble with tighten screw in the order of 3 to 1.

16

UD LINK ARM SL

MOTOR CHASSIS SL ASS’Y

2 UD link arm SL1 washer

Note:When reassembling motor chassis SL ass’y with the 2 screws, DO NOT let its Emergency Gear SL Teach touch the edge of the MA chassis SL S ass’yas they can be broken.

emergency gear SL

4 motor chassis SL ass’y

2 two screws(2.6 × 3)

4 two pet washers

1 anti rattle SP SL

5 sus base X sub ass’y

4 two pet washers

7 two UD S cam guide SL

6 mecha UD sub cam SL

4 two pet washers

plate spring SL

Note:Be sure that the plate spring SL is put on sus base X sub ass’y as shown in figure.

MA chassis SL ass’y

2 screw(2.6 × 3)

Note:Hook anti rattle SP SL on motor chassis SL ass’y as shown in figure.

3

Note:Reassemble UD S cam guide SL so that their wider sides come upper as shwon in Fig. E.

mecha UD sub cam SL Wide Wide

Narrow Narrow

mecha UD sub cam SL

UD S cam guide SLUD S cam guide SL

(fig. E)

LDG PLATE CAM SL(Page 18)

17

DISC LOCK ARM SL

INSTALLING THE DISC LOCK ARM SL

sellotape

(Fig. F. 1)

disc lock SL ass’y

D lock spring SL

2 washer

3 disc lock arm SL

1 Apply sellotape to the disc lock SL ass’y as shown infigure to prevent the disc lock from falling off while removing the disc arm SL.

disc lock arm SL

disc lock pinion

(Fig. F. 2)

washer

POSITIONING OF THE DISC LOCK ARM SL IS REQUIRED. (Refer to Fig. F. 2)

(1) Place the disc lock spring SL as shown in the figure.(2) Insert the disc lock pinion into the hole on the disc lock arm SL.(3) Adjust the position of the disc lock arm SL until its mark meets

the V-cut of the disc lock pinion as shown in the figure.

(4) Insert the shaft hole of the disc lock arm SL into the shaft.(5) Hook the end of the disc lock spring SL on the chassis hole as

shown in the figure.(6) Reassemble the washer in place.(7) Peel off the sellotape. Refer to Fig. F. 1.

18

STC POS GEAR SL

LDG PLATE CAM SL

2 LDG plate cam SL

1 washer

(Fig. G. 2)

(Fig. G. 1)

Note:Never use nail when turning the emergency gear SL.Otherwise, the gear tooth may be broken.

emergency gear SL

d

Note:DO NOT remove the STC POS GearSL together with the STC Motor SL Ass’y(Stocker) (M3), always replace it alone.

If they are removed at the same time andthe gear in the stocker height becomes outof position.

1 washer

2 STC POS gear SL

MA chassis SL S ass’y

STC POS gear SL

c

c

b

b

Note:Assemble the STC POS gearSL so that the mark on theSTC POS gear SL meets the mark on the MA chassis SLS ass’y.

POSITIONING OF THE STC POS GEAR SL REQUIRED

LDG plate cam SL

emergency gear SL

Note:Never use nail when turning the emergency gear SL.Otherwise the gear tooth may be broken.

e

d

ed

d

(Fig. G. 3)

(1) Turn the emergency gear SL in the direction of the arrow as shown in Fig. G. 1 until it stops.

(2) Assemble LDG plate cam SL so that the center of the LDG plate camSL, mark on the LDG plate cam SL and the center of the shaft are aligned on one line as shown in Fig. G. 2.

(3) Turn the emergency gear SL in revers until the marks , on LDG plate cam SL are almost aligened as shown in Fig. G. 3. (This operation is required to return to the mechanism in standby state.)

INSTALLING THE LDG PLATE CAM SL

POSITIONING OF THE LDG PLATE CAM SL IS REQUIRED.

19

SECTION 4ELECTRICAL ADJUSTMENT

Adjustment Location:

– MAIN R237 BOARD (Conductor Side) –

Procedure :1. Connect oscilloscope to TP101(pin 1: RFO) and TP101 (pin3: VC) on MAIN R237 board.

2. Press the I/1 button to turn the power on.3. Put test disc (YEDS-18) in and press the u button to play-

back.4. Adjust VR102 so that oscilloscope waveform is as shown in

the figure below. (eye pattern)A good eye pattern means that the diamond shape ( ) in thecenter of the waveform can be clearly distinguished.

5. After adjustment, check the RF signal level.

Forcus Bias Adjustment

Note:1. CD Block is basically designed to operate without adjustment.2. Use YEDS-18 disc (3-702-101-01)3. Use an oscilloscope with more than 10 MΩ impedance.4. Clean the object lens by an applicator with lens cleaning liq-

uid when the signal level is low than specified value with thefollowing adjustment.

5. Adjust the focus bias adjustment when optical block is replaced.

Focus Bias Adjustment

+–

MAIN R237 board

TP (RFO)TP (VC)

oscilloscope(DC range)

VOLT/DIV: 200 mVTIME/DIV: 500 ns

level:1.0 Vp-p+0.3

- 0.2

10: 1

TP101(Pin 1 : RFO)

TP101(Pin 3 : VC)

VR102FOCUS BIAS

ADJUSTMENT

s

20

MEMO

2121

SECTION 5DIAGRAMS

5-1. NOTE FOR PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS • Circuit Boards Location

Note on Schematic Diagram:• All capacitors are in µF unless otherwise noted. pF: µµF

50 WV or less are not indicated except for electrolyticsand tantalums.

• All resistors are in Ω and 1/4 W or less unless otherwise

specified.• 2 : nonflammable resistor.• C : panel designation.

• U : B+ Line.• V : B– Line.• H : adjustment for repair.• Voltages are taken with a VOM (Input impedance 10 MΩ).

Voltage variations may be noted due to normal produc-tion tolerances.

• Waveforms are taken with a oscilloscope.Voltage variations may be noted due to normal produc-tion tolerances.

• Circled numbers refer to waveforms.• Signal path.

F : TUNER (FM/AM)J : CD PLAYE : TAPE

Note:The components identi-fied by mark 0 or dottedline with mark 0 are criti-cal for safety.Replace only with partnumber specified.

Note:Les composants identifiés parune marque 0 sont critiquespour la sécurité.Ne les remplacer que par unepièce por tant le numérospécifié.

Note on Printed Wiring Board:• X : parts extracted from the component side.• Y : parts extracted from the conductor side.• z : Through hole.• b : Pattern from the side which enables seeing.(The other layers' patterns are not indicated.)

Caution:Pattern face side: Parts on the pattern face side seen from(Conductor Side) the pattern face are indicated.Parts face side: Parts on the parts face side seen from(Component Side) the parts face are indicated.

MAIN board

POWER SW board

FRONT board

TACT SW board

DOOR SW board

TUNER (FM/AM)

RELAY board

JACK board

PHOTO JACK board

AMP board

POWER SUPPLY board

AC board

TRA ASSY V619 MAIN R237 board

2222

HCD-LS1

5-2. PRINTED WIRING BOARD – CD Section – • See page 21 for Circuit Boards Location.

MAIN R237 BOARD (COMPONENT SIDE) MAIN R237 BOARD (CONDUCTOR SIDE)

C402

C404

R401

R418

C423

C406

C145

R13R14

R12R11R10

C521

L503

C516

C11

C12 R18

R134R136

R545

R133

C119

C128

C132

C126

R710

C120

C157

C134

R114

R702

R125

R126

R121

R122 R123

C114

C106

R177

R111C116

C115 R110

C133 R197

C117

C129

R112

R199R145

R144

R109R137C143

C137

R195

C110

R194

R127 R158

C103

C105

R142

R141

R101

C113

R700

C118

R423

L802

L401

R553

L402

R420

R405

R416

R518

C506

C419

R422

R408

R407

R552

R551

J404

R414

R530

R526

R409

R410

R532

R527

R528

R519

R516

R517

C505

R529

R524

C504

R406

C413

R415C4

14

R404

R402

R417

R411

R412

C422

R419

R603

R602

R113

C163

R15

C112R1

28C1

24R1

19R1

18C1

23C1

22

R143

C1

C165

R200

R706

R179

R103

R102

C107

R106

R105

R181

R180

C169

R196

R159

C102

L102

R147

R139

R117

C131

C130

L103

R19

R3

R2 R9

C135

C136

C138

R132

C142

R120

R17

R413

R403

R563

R554

R810

2

R8081

R8091

R8092

R8082

C1041

C1042

C1092

C1091

C111

1

C111

2

R810

1

R565

R564

C509

R531

B C E

B C E

BCE BCE

BC

E

B

C

E

Q412

B C E

B C E

Q521

Q522

B

C

E

BC

E

Q102Q103

Q8011

Q8012

B C E

Q411

Q413

Q502 Q501

BC

E Q402

D404

D101

D801

R573

C164

C140

R543

R548

R542

R541

R540

R539

R538

R537

R536

R510

R511

R508

R509

R512

R513

R549

R506

R507

R572

R571

R570

R714

R705

R709

R701

R712

R708

R713

R704

R707

R703

R711

R131C139R129R130

C8022

C8012C8011

R8012R8022R8032R8031

C8021R8011R8021

R4 R5 R6

C5071

C5072

R115R116C121

1 8

16

D406

AK

K

C409

C417

U502

9

C403

C405

D802A

A/K

K

C141

C8102

C8101

+

+

+

C162C127+

+

C125

+

C101

1

8 17

24

169

253232

+

C144CP102

ZD521

ZD403

ZD401

ZD502

Q404

Q401

ZD503

ZD405ZD404ZD402

C407

1

20

14

1

18

15

28

60

4140 21

61 80

U501

61

80

40

2120 1

41 60

U102

U404

U101

X101

CP103

122

CP101

1

16

8 5

1 4

U180

8

5

1

4U103

5

1

6

10

U106

5

1

6

10

U105

5

1

6

10

U107

ECB

E C B

Q414 E C B

Q403

BC

E

Q101

BC

E

D102 A K

KK

AX501

+

+

+

+

C411 +

+

+

D521AK K

D517

AK K

AK K

D409 K KA

D516K KA

KK

A

D401

KA

(CHASSIS)

C401+

CP502

1 5

CP503

1 3

CP501

1 7

U401

4 1

TP101

1

5

FORADJUSTMENT

VR102

L101

R124

R135

A D B C

OPTICAL PICK-UPBLOCK

(KSS-540A)

TRA ASSYV619

M2(SPINDLE)

M1(SLED)

M M

M4(LOADING)

M5(UP/DOWN)

M3(STOCKER)

M

M

M

CD SENSORBLOCK

05

1

A

2 3 4 5 6 7 8 9 10 11 12 13 14 15

B

C

D

E

F

G

H

I

J

K

L

(Page 26) (Page 30) (Page 26)

(Page 26)

2323

HCD-LS1

• SemiconductorLocation

5-3. SCHEMATIC DIAGRAM – CD Section (1/3) – • See page 33 for Waveforms.

• Voltages and waveforms are dc with respect to groundunder no-signal conditions.no mark : CD PLAY

The components identified by mark 0 or dottedline with mark 0 are critical for safety.Replace only with part number specified.

Les composants identifiés par une marque 0 sontcritiques pour la sécurité. Ne les remplacer quepar une pièce portant le numéro spécifié.

Ref. No. Location

D101 J-12D102 K-9D401 B-12D404 B-11D406 E-15D409 C-11D516 B-13D517 B-12D521 D-11D801 C-11

Q101 J-5Q102 I-10Q103 I-10Q401 D-7Q402 C-9Q403 E-2Q404 C-7Q411 B-13Q412 B-12Q413 B-12Q414 C-6Q501 C-13Q502 C-13Q521 C-11Q522 C-11Q8011 C-11Q8012 C-11

U101 K-5U102 J-7U103 I-7U105 H-2U106 H-2U107 H-2U180 J-4U401 B-9U404 J-3U501 J-2U502 C-3

ZD401 B-11ZD402 D-9ZD403 E-15ZD404 D-10ZD405 D-10ZD502 C-12ZD503 C-12ZD521 B-11

Note:• In the printed wiring diagram of the MAIN R237

Board, “A and L” or “B and R” of the last code of RefNo. on the silk-screen printing drawing of the mainunit are replace with “1” or “2” respectively.

Example: C104A → C1041R801R → R8012

(Page 24)

2424

HCD-LS1

5-4. SCHEMATIC DIAGRAM – CD Section (2/3) – • See page 33 for Waveforms. • See page 36 for IC Block Diagram.


(Page 23)

(Page 25)

(Page 27)

(Page 27)

(Page 27)

2525

HCD-LS1

5-5. SCHEMATIC DIAGRAM – CD Section (3/3) – • See page 33 for Waveform.


(Page 24)

(Page 31)

2626

HCD-LS1

5-6. PRINTED WIRING BOARDS – MAIN Section – • See page 21 for Circuit Boards Location.


Ref. No. Location

D200 F-2D251 B-5D252 B-4D253 C-3D254 B-4D304 H-4D312 C-3D316 G-4D321 D-2D352 E-3D391 B-2

IC103 C-8IC201 D-8IC251 C-5IC321 E-6IC351 F-4IC390 B-6IC391 C-7

PH200 E-2

Q201 C-4Q202 D-4Q203 C-5Q204 D-5Q205 D-3Q301 G-6Q302 G-6Q303 G-6Q304 F-9Q305 G-4Q306 H-8Q311 G-7Q312 G-7Q313 G-8Q316 G-4Q317 G-3Q321 E-5Q351 E-4Q352 E-4Q371 G-6Q372 F-6Q373 G-7Q374 F-7Q375 G-6Q376 G-5Q377 G-5Q381 F-8Q382 F-7Q383 G-8Q384 G-8

BC

E

BC

E

B C E

B C E

B C E

BC

E

BC

E

BC

E

B C E

B C E

SDG

B C E

C162

C163

D254 D252 D251

D253

D312

D321

D391

D352

++

+

+

+

+

+

L101

C159

C158

R321 R322R235R2

36

C241

C242R231

R233

R234

R282

R232

R229

R281R2

28

R227

R225

R222

R221 R237

R226

R238

C399

R366R365

R368R367

R315

R311R3

18

R373

R379

R381

C301

C306

R380

R314

R312

R313 R388R387

R397

R308

R309

R389R390

R363

R369

R364

R382

R370

R372

R377

R304

R357

R355

R356

R332

R329

R220R2

18

R216

R217

R257

R253

R251

R252

C253

R219

R204

R203

R201

R359

R358

R360

R354

R362

R352 R326 R328R327

R334R331R333

R325

R212R211

R214

R210

R209

R213

R145

R143

R144

R399

R215

R254

R391

R394

R393

R392

R258

R202

R353

R361

R351

C310 C309

R317

R316

R376

R375

R303

R371

R230

C200

R200

C102

C2001(C200A)

R2001(R200A)

1 8

16 9

IC103

1 14

28 15

IC201

Q304

Q384Q383

Q312Q313

Q374

BC

EB

CE

Q204

Q203

Q371

Q373

Q372

Q301Q303

Q316

B C E

Q317

Q311

Q306

BC

E

BCE

Q351

Q352

BC

E

Q305

IC3511

4

8

5

IC2511

4

8

5

IC391

1

6

5

10

IC321

1

4

8

5

Q202

Q205

Q201BCE

BCE

S D G

C214 C213

C201 C202

C355

C357

C359

C207

C208

C360

C358

C356

C327

C329

C328

C104

C237

C235

C233

C231

C238

C236

C103C330

C325 C324C323

C232

C367 C368

C249

C240 C239

C234

+ +

+

C157

+

C312

C161

C160

+

C243

+

C391

+

C392+

+

++

+

C255

+++C252

C251C257

C256

C321

C204

C290

C203C322

+

+ +

+

C216

C271C212

C211 C215

C272

+

+

+

+

+

+

+ +

+

C382

C305

C381

C384

C326 C362

C383

C385C386

C206

C205

+

+

C209

C210

C220

+ +

C333

+++

C313 C316

+

+

+

+

C308 C389 C388

C302C307

C334

+

C331

+

C387

D304

D316

D200

R142R256

R223

R307

R306

R305

X102

1-678-385-

11

1

PH200

CN200

3

PH200

CD DIGITALOUT

(OPTICAL)

PHOTO JACK BOARD

MAIN BOARD

1 2

CN2041 2

BC

E

BCE

R302

1

CN2017

Q377 Q375

Q382 Q381

Q376

Q302

1CN303

9 1

CN302

3 1

CN391

21

CN301

71

CN203

2

1

CN202

3

1

IC390

3

1415

21

CN101

12

2526

CN604

S392PANEL

OPEN/CLOSE

S3911 2 3 4 5

6 7 8 9 10

S391PANEL OPEN

MANUAL AUTO ON/AUTO

1 2 3 4 5

6 7 8 9 10

F

E

B

(AEP, UK) (AEP, UK)

1CN204

2

C G J H

A

M391(DOOR)M

1

A

2 3 4 5 6 7 8 9 10 11

B

C

D

E

F

G

H05

Q321

S

TUNE

R PA

CK (F

M/A

M)

(SUP

PLIE

D W

ITH

THE

ASSE

MBL

ED B

LOCK

)

ANTE

NNA

AM

FM 75Ω

(Page 30)

(Page 28)

(Page 22)

(Page 22) (Page 34) (Page 28) (Page 34)

(Page 22)

2727

HCD-LS15-7. SCHEMATIC DIAGRAM – MAIN Section – • See page 33 for Waveform. • See page 36 for IC Block Diagram.

• Voltages and waveforms are dc with respect to groundunder no-signal (detuned) conditions.no mark : TUNER (FM/AM)

∗ : Impossible to measure



(Page 24)(Page 24)

(Page 24)

(Page29)

(Page 31)

(Page 35)

(Page 35)

(Page 29)

2828

HCD-LS1

5-8. PRINTED WIRING BOARDS – AMP/RELAY/JACK Board – • See page 21 for Circuit Boards Location.


Ref. No. Location

D201 F-9D202 F-9D203 F-9D204 F-10D205 E-8D206 E-8D501 F-1D502 F-3D503 F-1D504 F-3D505 G-5D506 H-6D507 H-6D508 F-8D509 F-9D510 F-8D511 F-9D512 H-6D513 H-6D514 G-2D515 G-2D516 G-2

IC501 G-2IC502 F-11IC503 H-2

Q501 G-5Q502 F-9Q503 F-9Q504 G-5Q505 G-6

+

+

C505 C503

C514

3132

C557

C539

12

C540

C528

C529

C517

C512

+C511

+

C543

+

C510

+

+

+ +

C546

C544C545C527

+

+

C509

C508

+C507

+C516

+C515

C501 C5

02C5

06C5

04C5

13

C537

C538

C558

D503

D501

L503

C5011(C501A)

C5021(C502A)

C535

C533

C536

C534

C532

C542

C541

R503

R531

R529

R504R530

R536

R5281

4

8

5IC503

R532

R534R535

R533

R509

R510

R551

R543

R538

R549

R546

R548

R545

R544

R508

R507

R506

R505

D504

D514

D515

IC501

D502

D516

D505

D513 D507

D512

D506

L501

C550

L506

L504

L502

L505

R501

R502

7

1 9

CN501 CN505

1 6

12

AMP BOARD (COMPONENT SIDE) RELAY BOARD (COMPONENT SIDE)

AMP BOARD (CONDUCTOR SIDE)

RELAY BOARD (CONDUCTOR SIDE)

6

8

9

7

6

8

9

5 5

4 4

3 3

2 2

1 1

12

CN502

1

3

RY501

–1

–2

Q501 Q504 Q505

+–

CN504LEFT SPEAKER

(IMPEDANCE USE 4Ω)

+

–

CN503RIGHT SPEAKER

(IMPEDANCE USE 4Ω)

K J

1

A

2 3 4 5 6 7 8 9 10 11

B

C

D

E

F

G

H

C531

C547

C530

C518

C524 C523

+

+

C518

+

C549

+

+

+C548

1

2

3

1

2

3

1

1 2

2

3

21+

+

C555C204

C519

C552

C526

C525

C551

C206

C205

C203

C520

C554

C556

C553

R522

R521 R519

R553

R517

R552 R518

R550R523

R515

R513

R524

R526

R527 R5

25

R514

R520

R516

1

5 4IC502

8D201

D203

D202

D206

D205

D509

Q502 Q503

D508

D204

D510

D511

JK501

5462 3

1 21

3

JK201

21

3

JK202

1 7

CN201

6 1CN505

JACK BOARD (COMPONENT SIDE)

JACK BOARD (CONDUCTOR SIDE)

JK501PHONES

JK201TAPE OUT

JK202TAPE IN

E

Q502, 503

D509

05

C951

C952

C953

C954

C955

C959

C958

C957

C956

(Page 34) (Page 26)

(Page 26)

2929

HCD-LS1

5-9. SCHEMATIC DIAGRAM – AMP/RELAY/JACK Board –

• Voltages are dc with respect to ground under no-signal(detuned) conditions.no mark : TUNER (FM/AM)



(Page27)

(Page 35)

(Page 27)

3030

HCD-LS1

5-10. PRINTED WIRING BOARDS – PANEL Section (1/2) – • See page 21 for Circuit Boards Location.


Ref. No. Location

D601 D-8D602 D-8D603 E-2D604 D-2D605 E-7D606 E-4D607 E-4

IC601 C-5IC631 C-2

LED601 A-9LED602 A-1LED603 B-9LED604 B-1

Q601 E-2Q602 D-3Q613 C-2Q631 D-2Q632 D-1

SEN601 C-9

1-678-387- 11

C613+

C610

+

C603

L601

+

C635

1

+

C601

IC601

+

C608

CN602

+

D603

D604 D6

02

D601

R622

R621

R619

R618

R616

R615

CN604

R609

R626

C634

R617

R624 R623

R686

R628

R620

C633 C6

32

R632

R644

R601

C604

R602

R604

R608

R645

R603

R646

C607

C609

R643

R631

C631

R625

D606

D607 D605

X601

IC631

19

10 18

LCD601

R648

R642

JW60

1

C602

C612

R641

R613

R611

R610

R614

R627

R685

R612

R659

C606

R605

R607

R649

C626

C625

R650

C622

R658

1

3031

5051

80

100

81

Q601

SD

G

BCE

Q602BCE

SD

GQ631

Q632

Q613BCE

45

1

CN605

3

1SEN601 3

LR

1 7CN606

LED601, 603(LCD BACK LIGHT)

LED601

LED603

1

26

LED602, 604(LCD BACK LIGHT)

LED604

LED602

1

CN6012

1CN601

2

S615/

FRONT BOARD

POWER SW BOARD

LD

F

1

A

2 3 4 5 6 7 8 9

B

C

D

E

05

121

TO HAND SENSOR

(CHASSIS)

(Page 32)(Page 22)

(Page 26)

3131

HCD-LS1

5-11. SCHEMATIC DIAGRAM – PANEL Section (1/2) – • See page 33 for Waveform. • See page 36 for IC Block Diagram.

• Voltages and waveforms are dc with respect to groundunder no-signal (detuned) conditions.no mark : TUNER (FM/AM)( ) : CD PLAY


(Page32)

(Page 27)

(Page 25)

3232

HCD-LS1

5-12. PRINTED WIRING BOARDS – PANEL Section (2/2) – • See page 21 for Circuit Boards Location.


5-13. SCHEMATIC DIAGRAM – PANEL Section (2/2) –

Ref. No. Location

LED651 B-3LED652 B-4LED653 B-4LED654 B-5LED655 B-6LED656 C-3

R652 R653 R654 R655

R675

R676

R682R6

81

R680

R674

R673

R672

R679

R678

R671

R691

R657

R656

R683

R684

R677

R651

S603S602

S609

CN602

112

S610

S604

S611

S605

S612

S606

S613

S601FUNCTION

S614VOLUME –

S607VOLUME +LED651, S602

DISC 1 LED652, S603DISC 2

LED653, S604DISC 3

LED654, S605DISC 4

LED655, S606DISC 5

S608TUNER/BAND

LED651A AK

LED656A AK

LED652A AK

LED653A AK

LED654A AK

LED655A AK

LED656, S609

TUNER +TUNER –

S601-614

TACT SW BOARD

DOOR SW BOARD

1-678-836- 11

CN603

S691DOOR

OPEN/CLOSE

LED651-656

1

CN603

2

12

1

A

2 3 4 5 6 7

B

C

D05

L(Page 30)

(Page 31)

3333

• Waveforms– MAIN R237 Board –

1 U101 8 (TE), U102 ra (TE)(CD Play Mode)

2 U101 q; (FE), U102 el (FE)(CD Play Mode)

3 U101 wf (RFI), wg (RFO)U102 rd (RFDC), ta (RFAC)(CD Play Mode)

4 U102 yh (XTAI)

5 U501 yl (X2)

140 m Vp-pApprox.

200 mVp-pApprox.

Approx.1.2 Vp-p

2.4 Vp-p

16.9344 MHz

3.7 Vp-p

4.194304 MHz

3.2 Vp-p

4.332 MHz

5.2 Vp-p

5 MHz

– MAIN Board –

1 IC103 qd (XI)

– FRONT Board –

1 IC601 qj (X2)

3434

HCD-LS1

5-14. PRINTED WIRING BOARDS – POWER SUPPLY Section – • See page 21 for Circuit Boards Location.


Ref. No. Location

D1 H-6D2 H-6D3 H-6D4 H-6D5 G-5D6 F-4D7 F-4D8 G-4D9 G-4D10 E-6D11 H-6D12 H-5D13 F-6D14 F-6D15 F-6D16 F-8

IC1 G-5IC2 G-6IC3 G-6IC4 G-6IC5 G-9

Q1 H-6Q2 H-5Q3 H-5Q4 G-7Q5 F-8Q6 E-8Q7 F-8

POWER SUPPLY BOARD (COMPONENT SIDE)

POWER SUPPLY BOARD (CONDUCTOR SIDE)

1

IC5

10

1CN1

7 1CN3 3

1CN23

IC1

5

42

1

IC2 IC4

Q4

2

L1LINE

FILTER

3

14

Q1

Q2

Q3

Q5

Q7

Q6

T901DC/DC CONVERTER

5 1234

1234

6

IC3

1

3

+

(CHASSIS)

KHG

R16

R1

R11

R26

R25

R27

R30

R2

R7

R8

R5

R15

R14

R4

R3

R17

R6

R9 R10

R13

R28

R29

R23

R24

R12

D4

D2D1

D3

D9

D13D14

D10

D15

D16

D6 D7

D5D8

D12

D11

TH1

C2

C1

C3C4

C5

C8

C31

C9

C20

C21

C18

C12

C28

C10

C13

C27

R22

C25

C29

C30

C26 +

+

C23

+

C15

+

C22

+

+

C17

+

C6

+

+

C16

C24

+

+

C11 +

L4

L3

L2

FB1

1

2

1

2

AC IN

05

F501

1

A

2 3 4 5 6 7 8 9

B

C

D

E

F

G

H

GND1

AC BOARD (COMPONENT SIDE)

1-678-395- 11

AC BOARD (CONDUCTOR SIDE)

1-678-395- 11

(Page 26) (Page 26) (Page 28)

3535

HCD-LS1

5-15. SCHEMATIC DIAGRAM – POWER SUPPLY Section – • See page 36 for IC Block Diagram.

• Voltages are dc with respect to ground under no-signal(detuned) conditions.no mark : TUNER (FM/AM)




(Page 29)

(Page 27)

(Page 27)

3636

• IC Block Diagrams– MAIN R237 Board –

U102 CXD2587Q

– MAIN Board –

IC103 BU1924F (AEP, UK models)

– FRONT Board –

IC631 BU2092F-E2

– POWER SUPPLY Board –

IC5 LA5617

TERFDC

CEIGEN

AVSS

0

ADIO

AVDD

0

CLTV

FILO

AVSS

3

VSS

AVDD

3

DOUT

VDD

PCO

FILI

ASYO

ASYI

RFAC

BIAS

SSTP

DFCTMIRR

MDPLOCK

FOK

SFDR

VSS

TEST

FRDR

FEVC

COUT

SE

XTSLTES1

SRDRTFDR

FFDRTRDR

21

7071

6869

6667

64

65

62

61

63

7374

72

75

76

7778

7980

4

XRST

3

SQCK

SQSO

5 9876

5660 53545559 5758 5152 484950 47 444546 43 4142

XLAT

CLOK

SENS

SYSM

DATA

XUGF

XPCK GF

S

C2PO

WFC

K

10 11 12 13 14 15 16 17 18 19 20

21

222324

2526

3233

3031

3637

3435

3940

38

28

27

29

SPOA

ATSK

SCLK

VDD

SCOR

SPOB

XLON

XTAI

XVDD

EMPH

AVDD1AOUT1

AIN1

XTAOXVSS

AIN2

AOUT2AVDD2

RMUT

LOUT2

LOUT1

BCK

LRCK

PCMD

LMUT

AVSS1AVSS2

CPUINTERFACE

SERVO AUTOSEQUENCER

SERIAL ININTERFACE

OVER SAMPLINGDIGITAL FILTER

3rd ORDERNOISE SHAPER

PWM PWM

EFMDEMODULATOR

TIMINGLOGIC

DIGITALOUT

D/AINTERFACE

DIGITALPLL

ASYMMETRYCORRECTION

CLOCKGENERATOR

MIRR, DFCT,FOK

DETECTOR

DIGITALCLV

SUBCODEPROCESSOR

SERVOINTERFACE

SERVO DSP

FOCUSSERVO

TRACKINGSERVO

SLEDSERVO

PWM GENERATOR

FOCUS PWMGENERATOR

TRACKINGPWM GENERATOR

SLED PWMGENERATOR

16KRAM

ERRORCORRECTOR

INTE

RNAL

BUS

A/DCONVERTER

OPERATIONALAMPLIFIER

ANALOG SWITCH

ANAL

OG

DIGI

TAL

RCLK

NC XO XI VSS2

T2VDD2

T1

QUAL

RDAT

VREF

MUX

VDD1

VSS1

VSS3

CMP

1 43 65 872

141516 13 12 11 10 9

CLOCK

PLL 57kHzRDS/ARI

COMPARATOR

8th SWITCHEDCAPACITOR

FILTER

ANTI-ALIASINGFILTER

BIPHASEDECODER

PLL1187.5Hz

DEFFERENTIALDECODER

TEST

1 2 3 4 5 6 7 8 9

1016 15 14 13 12 11

CONTROLCIRCUIT

12 BITSHIFT

REGISTER

12 BITSTORAGEREGISTER

OUTPUTBUFFER

(OPEN DRAIN)

1718

VDD

OE Q11

Q10

Q9 Q8 Q7 Q6 Q5Q4Q3Q2Q1Q0LC

K

CLOC

K

DATAVSS

ON/OFF CURRENTLIMITER

STARTCIRCUIT

VREF

OVER HEATPROTECT

ON/OFFCURRENTLIMITER

1 2 3 4 5 6 7 8 9 10

VCC

VMUTE VCC

VREF

ERRORAMP

VREF

ERRORAMP

VO1

VCC

CN1 EN

EN D

ISPL

AY

GND NC CN2

VEE

VO2

~_1.8V

~_ 140

uACO

MPA

RATE

R

37

1

23

4

5

6

7not supplied 8

10

#2

9

16

D704

#2D703

D702

not supplied

not suppliedD701not supplied

not supplied

17#1

#4

18

19

202122notsupplied12

232526

274

29#1

#5

A

A

33

34

#2

30

3132

notsupplied

#1

28

24

11#3

#6

#6

#6

#1

notsupplied

notsupplied

12

13

21

14

SECTION 6EXPLODED VIEWS

Les composants identifiés par unemarque 0 sont critiquens pour lasécurité.Ne les remplacer que par une pièceportant le numéro spécifié.

The components identified bymark 0 or dotted line with mark0 are critical for safety.Replace only with part numberspecified.

• Items marked “*” are not stocked since theyare seldom required for routine service. Somedelay should be anticipated when orderingthese items.

• The mechanical parts with no reference num-ber in the exploded views are not supplied.

• Hardware (# mark) list is given in the last ofthe electrical parts list.

NOTE:• -XX and -X mean standardized parts, so they

may have some difference from the originalone.

• Color Indication of Appearance PartsExample:KNOB, BALANCE (WHITE) . . . (RED)

↑ ↑Parts Color Cabinet's Color

Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark

1 X-4953-040-1 SLIDE DOOR ASSY2 4-229-209-01 FUNCTION PANEL3 4-229-217-01 MAIN CASE4 4-229-220-01 SP. SCREW5 4-229-208-01 FRONT WINDOW

6 4-229-214-01 FRONT SCREW7 4-229-216-01 AL PANEL8 4-229-219-01 POWER BUTTON (SUB)9 PCB BRACKET10 1-678-387-11 POWER SW BOARD

11 8-719-070-85 HAND SENSOR KU381-4012 4-229-242-01 SP. HOOK BKT.13 4-229-201-01 +B 2X8 SCREW14 1-792-759-11 FFC (12CORE)16 A-4473-557-A FRONT BOARD, COMPLETE

17 1-792-758-11 FFC (26CORE)18 A-4473-559-A TACT SW BOARD, COMPLETE19 FIBER WASHER20 X-4953-039-1 FUNCTION BUTTON ASSY

21 LIGHT LEAK SEAL A22 LIGHT LEAK SEAL B23 4-229-330-01 SHEET METAL, EARTH24 4-229-227-01 COIL SPRING25 4-229-241-01 SCREW (2.6X6), TAPPING

26 DOOR SPRING27 4-229-240-01 SLIDE DOOR WASHER28 SLIDE DOOR CUSHION29 1-678-386-11 DOOR SW BOARD30 4-229-226-01 WORM GEAR HOLDER

31 4-229-222-01 WORM GEAR32 X-4953-041-1 GEAR ASSY33 4-229-264-01 BELT34 4-229-259-01 BOTTOM COVERD701 8-719-991-33 DIODE 1SS133T-77

D702 8-719-991-33 DIODE 1SS133T-77D703 8-719-991-33 DIODE 1SS133T-77D704 8-719-991-33 DIODE 1SS133T-77

(1) MAIN CASE SECTION

38


51 4-229-265-01 MECHA, HOLDER52 A-4473-561-A MAIN BOARD, COMPLETE53 1-500-386-11 FILTER, CLAMP (FERRITE CORE)54 4-229-328-01 EGG TERMINAL55 1-678-395-11 AC BOARD

56 A-4473-563-A POWER SUPPLY BOARD, COMPLETE57 A-4473-565-A RELAY BOARD, COMPLETE58 A-4473-564-A AMP BOARD, COMPLETE59 A-4473-566-A JACK BOARD, COMPLETE60 FFC (15CORE)

61 1-693-473-21 TUNER PACK (FM/AM)62 X-4953-038-1 TOP PANEL ASSY

63 4-229-260-01 SLIDE KNOB64 SLIDE KNOB PLATE65 A-4473-562-A PHOTO JACK BOARD, COMPLETE66 4-229-258-01 BOTTOM CASE67 1-792-757-11 AC CORD (POWER)

68 4-229-263-01 AC CORD STOPPERD705 8-719-991-33 DIODE 1SS133T-77D706 8-719-991-33 DIODE 1SS133T-77D707 8-719-991-33 DIODE 1SS133T-77D708 8-719-991-33 DIODE 1SS133T-77

D801 8-719-070-85 DIODE KU381-4M391 X-4953-037-1 MOTOR PULLEY ASSY (DOOR)

#7

notsupplied

#19

#19

D707

D708 D801

notsupplied

notsupplied

notsupplied

notsupplied

notsupplied

not supplied

not supplied

#7

#9

#18

#6

60

D706

D705

61

6263

64

65 66#8

59

#1B

#8#19

68

67

#13#2

not supplied

not supplied

not supplied

not supplied

M391

53

52

56

#19

#19

#20

#1

#1

57

58

#19

54

55

B

51

51

not supplied

(2) BOTTOM CASE SECTION

39


101 4-229-348-01 F PANEL ASSY R237102 4-229-314-01 PCB FLEX MECHA ASSY103 4-229-318-01 MECH UD SUB CAM SL104 4-229-315-01 PET WASHER105 4-229-312-01 SUS BASE X SUB ASSY

106 4-229-324-01 ANTI RATTLE SP SL107 4-229-295-01 SCREW 2.6X3108 4-229-325-01 DAMPER SCREW SL109 4-229-350-01 TOP COVER HS ASSY110 4-229-327-01 DUST SEAL EMA SL

111 4-229-311-01 WASHER112 4-229-287-01 STC POS GEAR SL113 4-229-293-01 STC MOTOR SHEET SL114 4-229-294-01 WASHER115 4-229-291-01 STC WORM GEAR SL

116 4-229-286-01 STC C IDLE GEAR SL117 4-229-283-01 DISC LOCK SL ASSY118 4-229-292-01 STC IDLE GEAR SL119 STC SCREW GEAR SL

120 STC SCREW NUT A SL121 4-229-320-01 STC SPRING B SL122 4-229-317-01 STC SP CAP A SL123 STOCKER CD SL124 4-229-316-01 STC SP CAP B SL

125 4-229-319-01 STC SPRING A SL126 4-229-321-01 STC SPRING C SL127 4-229-282-01 MA CHASSIS SL S ASSY128 4-229-351-01 HEAT SINK REG129 4-229-289-01 D LOCK SPRING SL

130 4-229-288-01 DISC LOCK ARM SL131 4-229-326-01 WASHER132 4-229-322-01 UD LINK ARM SL133 4-229-323-01 PLATE SPRING SL134 4-229-290-01 UD S CAM GUIDE SL

135 4-229-313-01 FR CHASSIS SL ASSY136 A-4473-555-A MAIN R237 BOARD, COMPLETE137 4-229-349-01 BOTTOM COVER MF ASSYM3 4-229-284-01 STC MOTOR SL ASSY (STOCKER)

109

Loading MF ass’y

107

107

C

D

Motor chassisSL ass’y

Traverse mechaass’y

108108

107104

106#12

104105

#11 104103

104110

111

112113

115

114

107

116 111

117118

111

119

120

121

122

F

M3

123#13

124122

125

126

120

119111

118

#14

FE

127129

130

111128

#15136

131

132

135

#11

134107

133

#10

#10

#10

137101

102 #11

#11 #11

C

E

D

(3) MECHANISM DECK SECTION-1(HG-1: MAIN SECTION)

40


151 4-229-306-01 EMERGENCY GEAR SL152 4-229-308-01 BRACKET SCREW SL153 4-229-311-01 WASHER154 4-229-301-01 MECHA UD GEAR SL155 4-229-305-01 LDG PLATE CAM SL

156 4-229-307-01 UD WORM PLATE SL157 4-229-310-01 E-RING158 4-229-300-01 UD WORM GEAR SL159 4-229-302-01 MEC SENSOR RING SL

160 4-229-303-01 LDG WORM GEAR SL161 4-229-304-01 LDG SENSOR RING SL162 UD CAM GUIDE SL163 4-229-299-01 UD CAM SL164 4-229-309-01 UD CAM GUIDE W SL

165 4-229-296-01 MO CHASSIS SL S ASSYM4 4-229-297-01 LDG MOTOR SL ASSY (LOADING)M5 4-229-298-01 UD MOTOR SL ASSY (UP/DOWN)

153

155

152

M5

151

153

154

159

158

157

156

#13

160

162

#16

163

164

161

152 165

M4

(4) MECHANISM DECK SECTION-2(HG-1: MOTOR CHASSIS SL ASS’Y)

41

206

206

207 206

208

#12204

203

M1

214202

201

#12

#13

#13

#17

215

214

213

210

M2

204

211

212

209

205


201 4-229-268-01 TRA ASSY V619202 1-792-692-11 WIRE FLEXIBLE BOARD203 4-229-276-01 FIRST GEAR204 4-229-273-01 DAMPER S SL205 4-229-278-01 THIRD GEAR

206 4-229-294-01 WASHER207 4-229-277-01 SECOND GEAR208 4-229-272-01 POWER GEAR

209 4-229-280-01 SCREW 2X4210 4-229-275-01 PU G PLATE H SL211 4-229-279-01 RACK CA

0212 1-251-883-11 OPTICAL PICK-UP KSS-540A213 1-678-133-11 PICK-UP FLEXIBLE BOARD

214 4-229-271-01 SH LOCK PLATE SL215 4-229-270-01 PU GUIDE SHAFT SLM1 1-763-519-11 MOTOR (SLED)M2 4-229-269-01 DISC MOTOR CH ASSY (SPINDLE)

(5) MECHANISM DECK SECTION-3(HG-1: TRAVERSE MECHA ASS’Y)

The components identified bymark 0 or dotted line withmark 0 are critical for safety.Replace only with part num-ber specified.

Les composants identifiés par unemarque 0 sont critiques pour lasécurité.Ne les remplacer que par une pièceportant le numéro spécifié.

42


251 4-229-188-01 SHUT ARM SHAFT SL252 4-229-193-01 SHUTTER ARM SL253 4-229-187-01 SHUT ARM CUSH SL254 LOADING CHASSIS SL ASSY255 4-229-196-01 SHUTTER LEVER SL

256 4-229-192-01 SHUTTER SPRING SL257 4-229-191-01 LDG CENTER GEAR SL258 4-229-183-01 LOADING L MF ASSY259 4-229-190-01 LDG RETURN SP SL260 4-229-197-01 DISC G UPPER SL

261 4-229-200-01 DISC CRAMP BASE262 4-229-198-01 STEEL RING263 4-229-294-01 WASHER264 4-229-185-01 LDG LINK SL ASSY265 4-229-184-01 LOADING R MF ASSY

266 4-229-189-01 CLAMPER RE SP SL267 4-229-195-01 CLAMP HOLDER L SL268 4-229-199-01 CLAMP TOP269 4-229-186-01 BT 1.7X5 +PAN (0 TYPE 3)270 4-229-194-01 CLAMP HOLDER R SL

262261

260

259

263

264257

258

256

255265

266

267

268269

270

251

252

253

254

(6) MECHANISM DECK SECTION-4(HG-1: LOADING MF ASS’Y)

43

SECTION 7ELECTRICAL PARTS LIST AC AMP


1-678-395-11 AC BOARD*********

4-229-206-01 TERMINAL PIN (K)4-229-207-01 TERMINAL PIN (L)1-576-450-11 FUSE HOLDER

< FUSE >

0F501 1-532-465-31 FUSE (3.15A/250V)**************************************************************

A-4473-564-A AMP BOARD, COMPLETE********************

4-229-344-01 SCREW (3X1), TAPPING4-229-345-01 INSULATING SHEET (A)4-229-346-01 INSULATING SHEET (B)

< CAPACITOR >

C501 1-136-165-00 MYLAR 0.1uF 5% 50VC502 1-136-165-00 MYLAR 0.1uF 5% 50VC503 1-136-846-11 MYLAR 1.5uF 5% 50VC504 1-136-846-11 MYLAR 1.5uF 5% 50VC505 1-136-846-11 MYLAR 1.5uF 5% 50V

C506 1-136-846-11 MYLAR 1.5uF 5% 50VC507 1-126-012-11 ELECT 470uF 20% 16VC508 1-126-012-11 ELECT 470uF 20% 16VC509 1-126-044-11 ELECT 1uF 20% 50VC510 1-126-044-11 ELECT 1uF 20% 50VC511 1-126-052-11 ELECT 100uF 20% 16V

C512 1-126-052-11 ELECT 100uF 20% 16VC513 1-136-177-00 MYLAR 1uF 5% 50VC514 1-136-165-00 MYLAR 0.1uF 5% 50VC515 1-124-360-00 ELECT 1000uF 20% 16VC516 1-124-360-00 ELECT 1000uF 20% 16V

C517 1-136-177-00 MYLAR 1uF 5% 50VC528 1-136-165-00 MYLAR 0.1uF 5% 50VC529 1-136-165-00 MYLAR 0.1uF 5% 50VC532 1-163-038-00 CERAMIC CHIP 0.1uF 25VC533 1-163-038-00 CERAMIC CHIP 0.1uF 25V

C534 1-163-038-00 CERAMIC CHIP 0.1uF 25VC535 1-163-038-00 CERAMIC CHIP 0.1uF 25VC536 1-163-038-00 CERAMIC CHIP 0.1uF 25VC537 1-136-169-00 MYLAR 0.22uF 5% 50VC538 1-136-169-00 MYLAR 0.22uF 5% 50V

C539 1-136-169-00 MYLAR 0.22uF 5% 50VC540 1-136-169-00 MYLAR 0.22uF 5% 50VC541 1-163-038-00 CERAMIC CHIP 0.1uF 25VC542 1-163-038-00 CERAMIC CHIP 0.1uF 25VC543 1-126-933-11 ELECT 100uF 20% 16V

C550 1-124-724-11 ELECT 47uF 20% 16VC557 1-137-505-11 MYLAR 220PF 5% 50VC558 1-137-505-11 MYLAR 220PF 5% 50V

C591 1-135-838-11 CERAMIC 2000PFC592 1-135-838-11 CERAMIC 2000PFC593 1-135-838-11 CERAMIC 2000PFC594 1-135-838-11 CERAMIC 2000PFC595 1-135-838-11 CERAMIC 2000PF

C596 1-135-838-11 CERAMIC 2000PFC597 1-135-838-11 CERAMIC 2000PFC598 1-135-838-11 CERAMIC 2000PFC599 1-135-838-11 CERAMIC 2000PF

< DIODE >

D501 8-719-210-21 DIODE 11EQS04D502 8-719-210-21 DIODE 11EQS04D503 8-719-210-21 DIODE 11EQS04D504 8-719-210-21 DIODE 11EQS04D514 8-719-820-58 DIODE 1SS177

D515 8-719-820-58 DIODE 1SS177D516 8-719-820-58 DIODE 1SS177

< IC >

IC501 8-759-638-11 IC TA2020-020IC503 8-759-100-96 IC NJM4558M

< COIL >

L501 1-419-281-11 INDUCTOR 10uHL502 1-419-281-11 INDUCTOR 10uHL503 1-419-281-11 INDUCTOR 10uHL504 1-419-281-11 INDUCTOR 10uHL505 1-419-282-11 INDUCTOR 10uH

L506 1-410-509-11 INDUCTOR 10uH

< RESISTOR >

0R501 1-215-857-11 METAL OXIDE 10 5% 1W F0R502 1-215-857-11 METAL OXIDE 10 5% 1W F

R503 1-216-222-00 RES, CHIP 10K 5% 1/8W

NOTE:• Due to standardization, replacements in the

parts list may be different from the parts speci-fied in the diagrams or the components usedon the set.

• -XX and -X mean standardized parts, so theymay have some difference from the originalone.

• RESISTORSAll resistors are in ohms.METAL: Metal-film resistor.METAL OXIDE: Metal oxide-film resistor.F: nonflammable

• Items marked “*” are not stocked since theyare seldom required for routine service.Some delay should be anticipated when order-ing these items.

• SEMICONDUCTORSIn each case, u: µ, for example:uA. . : µA. . uPA. . : µPA. .uPB. . : µPB. . uPC. . : µPC. .uPD. . : µPD. .

• CAPACITORSuF: µF

• COILSuH: µH

Les composants identifiés par unemarque 0 sont critiquens pour lasécurité.Ne les remplacer que par une pièceportant le numéro spécifié.

The components identified bymark 0 or dotted line with mark0 are critical for safety.Replace only with part numberspecified.

When indicating parts by referencenumber, please include the board.

44


AMP DOOR SW FRONT

R504 1-216-222-00 RES, CHIP 10K 5% 1/8WR505 1-216-230-00 RES, CHIP 22K 5% 1/8W

R506 1-216-230-00 RES, CHIP 22K 5% 1/8WR507 1-216-220-00 RES, CHIP 8.2K 5% 1/8WR508 1-216-246-00 RES, CHIP 100K 5% 1/8WR528 1-216-270-00 RES, CHIP 1M 5% 1/8WR529 1-216-270-00 RES, CHIP 1M 5% 1/8WR530 1-216-270-00 RES, CHIP 1M 5% 1/8W

R531 1-216-270-00 RES, CHIP 1M 5% 1/8WR532 1-216-262-00 RES, CHIP 470K 5% 1/8WR533 1-216-262-00 RES, CHIP 470K 5% 1/8WR534 1-216-262-00 RES, CHIP 470K 5% 1/8WR535 1-216-262-00 RES, CHIP 470K 5% 1/8W

R536 1-216-174-00 RES, CHIP 100 5% 1/8W**************************************************************

1-678-386-11 DOOR SW BOARD***************

< RESISTOR >

R691 1-216-073-00 METAL CHIP 10K 5% 1/10W

< SWITCH >

S691 1-771-960-11 LEAF SW (DOOR OPEN/CLOSE)**************************************************************

A-4473-557-A FRONT BOARD, COMPLETE**********************

4-229-202-01 BACK LIGHT WINDOW

< CAPACITOR >

C601 1-126-916-11 ELECT 1000uF 20% 6.3VC602 1-163-033-00 CERAMIC CHIP 0.022uF 50VC603 1-125-972-91 ELECT 100uF 20% 16VC604 1-163-038-00 CERAMIC CHIP 0.1uF 25VC606 1-163-038-00 CERAMIC CHIP 0.1uF 25V

C607 1-163-038-00 CERAMIC CHIP 0.1uF 25VC608 1-126-160-11 ELECT 1uF 20% 50VC609 1-163-038-00 CERAMIC CHIP 0.1uF 25VC610 1-124-589-11 ELECT 47uF 20% 16VC612 1-163-033-00 CERAMIC CHIP 0.022uF 50V

C613 1-126-160-11 ELECT 1uF 20% 50VC622 1-163-117-00 CERAMIC CHIP 100PF 5% 50VC625 1-163-102-00 CERAMIC CHIP 24PF 5% 50VC626 1-163-102-00 CERAMIC CHIP 24PF 5% 50VC631 1-163-009-11 CERAMIC CHIP 0.001uF 10% 50V

C632 1-163-009-11 CERAMIC CHIP 0.001uF 10% 50VC633 1-163-009-11 CERAMIC CHIP 0.001uF 10% 50VC634 1-163-033-00 CERAMIC CHIP 0.022uF 50VC635 1-124-247-91 ELECT 10uF 20% 35V

< CONNECTOR >

CN602 1-794-485-11 CONNECTOR 12PCN604 1-794-484-11 CONNECTOR 26PCN605 1-794-486-11 CONNECTOR 3P

< DIODE >

D601 8-719-200-02 DIODE 1N4002D602 8-719-200-02 DIODE 1N4002D603 8-719-991-33 DIODE 1SS133T-77D604 8-719-991-33 DIODE 1SS133T-77D605 8-719-991-33 DIODE 1SS133T-77

D606 8-719-991-33 DIODE 1SS133T-77D607 8-719-991-33 DIODE 1SS133T-77

< IC >

IC601 8-759-677-45 IC LC867232A-5P06IC631 8-759-396-78 IC BU2092F-E2

< RESISTOR >

JW601 1-216-053-00 METAL CHIP 1.5K 5% 1/10W

< COIL >

L601 1-419-636-11 COIL, CHOKE

< LIQUID CRYSTAL DISPLAY >

LCD601 1-804-047-11 LCD

< LED >

LED601 8-719-069-45 LED SELU5E23C-TP15 (LCD BACK LIGHT)LED602 8-719-069-45 LED SELU5E23C-TP15 (LCD BACK LIGHT)LED603 8-719-069-45 LED SELU5E23C-TP15 (LCD BACK LIGHT)LED604 8-719-069-45 LED SELU5E23C-TP15 (LCD BACK LIGHT)

< TRANSISTOR >

Q601 8-729-120-28 TRANSISTOR 2SC1623-L6Q602 8-729-120-28 TRANSISTOR 2SC1623-L6Q613 8-729-120-28 TRANSISTOR 2SC1623-L6Q614 8-729-029-66 TRANSISTOR DTC114ESAQ615 8-729-029-66 TRANSISTOR DTC114ESA

Q631 8-729-052-45 FET 2SJ461Q632 8-729-052-45 FET 2SJ461

< RESISTOR >

R601 1-216-089-00 RES, CHIP 47K 5% 1/10WR602 1-216-049-11 RES, CHIP 1K 5% 1/10WR603 1-216-089-00 RES, CHIP 47K 5% 1/10WR604 1-216-089-00 RES, CHIP 47K 5% 1/10WR605 1-216-049-11 RES, CHIP 1K 5% 1/10W

R607 1-216-065-00 RES, CHIP 4.7K 5% 1/10WR608 1-216-049-11 RES, CHIP 1K 5% 1/10WR609 1-216-065-00 RES, CHIP 4.7K 5% 1/10WR610 1-216-049-11 RES, CHIP 1K 5% 1/10WR611 1-216-049-11 RES, CHIP 1K 5% 1/10W

R612 1-216-049-11 RES, CHIP 1K 5% 1/10WR613 1-216-049-11 RES, CHIP 1K 5% 1/10WR614 1-216-049-11 RES, CHIP 1K 5% 1/10WR615 1-249-049-11 CARBON 1K 5% 1/4WR616 1-249-049-11 CARBON 1K 5% 1/4W

R617 1-216-049-11 RES, CHIP 1K 5% 1/10WR618 1-249-049-11 CARBON 1K 5% 1/4WR619 1-249-049-11 CARBON 1K 5% 1/4W

45


R620 1-216-065-00 RES, CHIP 4.7K 5% 1/10WR621 1-249-429-11 CARBON 10K 5% 1/4W

R622 1-249-429-11 CARBON 10K 5% 1/4WR623 1-216-097-00 RES, CHIP 100K 5% 1/10WR624 1-216-097-00 RES, CHIP 100K 5% 1/10WR625 1-216-097-00 RES, CHIP 100K 5% 1/10WR626 1-216-097-00 RES, CHIP 100K 5% 1/10W

R627 1-216-021-00 METAL CHIP 68 5% 1/10WR628 1-216-021-00 METAL CHIP 68 5% 1/10WR630 1-216-049-91 RES, CHIP 1K 5% 1/10WR631 1-216-097-00 RES, CHIP 100K 5% 1/10WR632 1-216-097-00 RES, CHIP 100K 5% 1/10W

R633 1-216-029-00 RES, CHIP 150 5% 1/10WR641 1-216-073-00 METAL CHIP 10K 5% 1/10W

R642 1-216-073-00 METAL CHIP 10K 5% 1/10WR643 1-216-073-00 METAL CHIP 10K 5% 1/10WR644 1-216-073-00 METAL CHIP 10K 5% 1/10WR645 1-216-073-00 METAL CHIP 10K 5% 1/10WR646 1-216-073-00 METAL CHIP 10K 5% 1/10W

R648 1-216-073-00 METAL CHIP 10K 5% 1/10WR649 1-216-073-00 METAL CHIP 10K 5% 1/10WR650 1-216-073-00 METAL CHIP 10K 5% 1/10WR658 1-216-065-00 RES, CHIP 4.7K 5% 1/10WR659 1-216-089-00 RES, CHIP 47K 5% 1/10W

R685 1-216-045-00 METAL CHIP 680 5% 1/10WR686 1-216-045-00 METAL CHIP 680 5% 1/10W

< IC >

SEN601 8-749-017-81 IC SPS-446 (REMOTE CONTROL RECEIVER)

< VIBRATOR >

X601 1-781-679-11 VIBRATOR, CRYSTAL (5MHz)**************************************************************

A-4473-566-A JACK BOARD, COMPLETE*********************

< CAPACITOR >

C203 1-163-038-00 CERAMIC CHIP 0.1uF 25VC204 1-163-038-00 CERAMIC CHIP 0.1uF 25VC205 1-163-038-00 CERAMIC CHIP 0.1uF 25VC206 1-163-038-00 CERAMIC CHIP 0.1uF 25VC518 1-128-526-11 ELECT 220uF 20% 10V

C519 1-163-009-11 CERAMIC CHIP 0.001uF 10% 50VC520 1-163-009-11 CERAMIC CHIP 0.001uF 10% 50VC523 1-126-868-11 ELECT 47uF 20% 50VC524 1-126-868-11 ELECT 47uF 20% 50VC525 1-163-009-11 CERAMIC CHIP 0.001uF 10% 50V

C526 1-163-009-11 CERAMIC CHIP 0.001uF 10% 50VC530 1-104-942-11 ELECT 1uF 20% 50VC531 1-104-942-11 ELECT 1uF 20% 50VC547 1-128-526-11 ELECT 220uF 20% 10VC548 1-126-163-11 ELECT 4.7uF 20% 50V

C549 1-126-163-11 ELECT 4.7uF 20% 50VC551 1-163-038-00 CERAMIC CHIP 0.1uF 25VC552 1-163-038-00 CERAMIC CHIP 0.1uF 25VC553 1-163-129-00 CERAMIC CHIP 330PF 5% 50V

C554 1-163-129-00 CERAMIC CHIP 330PF 5% 50V

C555 1-163-133-00 CERAMIC CHIP 470PF 5% 50VC556 1-163-133-00 CERAMIC CHIP 470PF 5% 50V

< DIODE >

D201 8-719-947-61 DIODE MTZJ-T-72-15BD202 8-719-947-61 DIODE MTZJ-T-72-15BD203 8-719-947-61 DIODE MTZJ-T-72-15BD204 8-719-947-61 DIODE MTZJ-T-72-15BD205 8-719-820-58 DIODE 1SS177

D206 8-719-820-58 DIODE 1SS177D508 8-719-947-61 DIODE MTZJ-T-72-15BD509 8-719-947-61 DIODE MTZJ-T-72-15BD510 8-719-820-58 DIODE 1SS177D511 8-719-820-58 DIODE 1SS177

< IC >

IC502 8-759-711-82 IC NJM4580E

< JACK >

JK201 1-563-281-41 JACK (TAPE OUT)JK202 1-563-281-41 JACK (TAPE IN)JK501 1-794-492-11 HP JACK (PHONES)

< TRANSISTOR >

Q502 8-729-231-55 TRANSISTOR 2SC2878-AQ503 8-729-231-55 TRANSISTOR 2SC2878-A

< RESISTOR >

R511 1-216-138-00 RES, CHIP 3.3 5% 1/8WR513 1-216-206-00 RES, CHIP 2.2K 5% 1/8WR514 1-216-206-00 RES, CHIP 2.2K 5% 1/8WR515 1-216-238-91 RES, CHIP 47K 5% 1/8WR516 1-216-238-91 RES, CHIP 47K 5% 1/8WR517 1-216-210-00 RES, CHIP 3.3K 5% 1/8W

R518 1-216-210-00 RES, CHIP 3.3K 5% 1/8WR519 1-216-254-00 RES, CHIP 220K 5% 1/8WR520 1-216-254-00 RES, CHIP 220K 5% 1/8WR521 1-216-190-00 RES, CHIP 470 5% 1/8WR522 1-216-190-00 RES, CHIP 470 5% 1/8W

R523 1-216-182-00 RES, CHIP 220 5% 1/8WR524 1-216-150-00 RES, CHIP 10 5% 1/8WR525 1-216-150-00 RES, CHIP 10 5% 1/8WR526 1-216-214-00 RES, CHIP 4.7K 5% 1/8WR527 1-216-214-00 RES, CHIP 4.7K 5% 1/8W

R550 1-216-182-00 RES, CHIP 220 5% 1/8WR552 1-216-230-00 RES, CHIP 22K 5% 1/8WR553 1-216-230-00 RES, CHIP 22K 5% 1/8W

**************************************************************

A-4473-561-A MAIN BOARD, COMPLETE*********************

< CAPACITOR >

C102 1-163-038-00 CERAMIC CHIP 0.1uF 25VC103 1-130-471-00 MYLAR 0.001uF 5% 50VC104 1-130-471-00 MYLAR 0.001uF 5% 50V

FRONT JACK MAIN

46


MAIN

C157 1-124-589-11 ELECT 47uF 20% 16V(AEP, UK)

C158 1-163-135-00 CERAMIC CHIP 560PF 5% 50V(AEP, UK)

C159 1-163-127-00 CERAMIC CHIP 270PF 5% 50V(AEP, UK)

C160 1-126-162-11 ELECT 3.3uF 20% 50V(AEP, UK)

C161 1-124-589-11 ELECT 47uF 20% 16V(AEP, UK)

C162 1-102-518-11 CERAMIC 33PF 5% 50V(AEP, UK)

C163 1-102-518-11 CERAMIC 33PF 5% 50V(AEP, UK)

C201 1-130-471-00 MYLAR 0.001uF 5% 50VC202 1-130-471-00 MYLAR 0.001uF 5% 50VC203 1-126-045-11 ELECT 2.2uF 20% 50VC204 1-126-045-11 ELECT 2.2uF 20% 50VC205 1-126-045-11 ELECT 2.2uF 20% 50V

C206 1-126-045-11 ELECT 2.2uF 20% 50VC207 1-137-503-11 MYLAR 0.0001uF 5% 50VC208 1-137-503-11 MYLAR 0.0001uF 5% 50VC209 1-126-045-11 ELECT 2.2uF 20% 50VC210 1-126-045-11 ELECT 2.2uF 20% 50V

C211 1-126-045-11 ELECT 2.2uF 20% 50VC212 1-126-045-11 ELECT 2.2uF 20% 50VC213 1-130-471-00 MYLAR 0.001uF 5% 50VC214 1-130-471-00 MYLAR 0.001uF 5% 50VC215 1-126-045-11 ELECT 2.2uF 20% 50V

C216 1-126-045-11 ELECT 2.2uF 20% 50VC220 1-124-673-11 ELECT 100uF 20% 10VC231 1-137-440-11 MYLAR 0.018uF 5% 50VC232 1-137-440-11 MYLAR 0.018uF 5% 50VC233 1-137-372-11 MYLAR 0.022uF 5% 50V


C239 1-137-437-11 MYLAR 0.0056uF 5% 50VC240 1-137-437-11 MYLAR 0.0056uF 5% 50VC241 1-163-125-00 CERAMIC CHIP 220PF 5% 50VC242 1-163-125-00 CERAMIC CHIP 220PF 5% 50VC243 1-124-261-00 ELECT 10uF 20% 50V

C249 1-130-495-00 MYLAR 0.1uF 5% 50VC251 1-124-257-00 ELECT 2.2uF 20% 50VC252 1-124-257-00 ELECT 2.2uF 20% 50VC253 1-163-009-11 CERAMIC CHIP 0.001uF 10% 50VC255 1-125-972-91 ELECT 100uF 20% 16V

C256 1-125-972-91 ELECT 100uF 20% 16VC257 1-124-464-11 ELECT 0.22uF 20% 50VC271 1-126-045-11 ELECT 2.2uF 20% 50VC272 1-126-045-11 ELECT 2.2uF 20% 50VC290 1-124-673-11 ELECT 100uF 20% 10V

C301 1-163-037-11 CERAMIC CHIP 0.022uF 10% 50VC302 1-125-972-91 ELECT 100uF 20% 16VC305 1-125-972-91 ELECT 100uF 20% 16VC306 1-163-037-11 CERAMIC CHIP 0.022uF 10% 50VC307 1-125-972-91 ELECT 100uF 20% 16V

C308 1-125-972-91 ELECT 100uF 20% 16VC309 1-164-004-11 CERAMIC CHIP 0.1uF 10% 25VC310 1-163-037-11 CERAMIC CHIP 0.022uF 10% 50VC312 1-125-972-91 ELECT 100uF 20% 16VC313 1-125-972-91 ELECT 100uF 20% 16V

C316 1-124-589-11 ELECT 47uF 20% 16VC321 1-126-045-11 ELECT 2.2uF 20% 50VC322 1-126-045-11 ELECT 2.2uF 20% 50VC323 1-137-361-11 MYLAR 330PF 5% 50VC324 1-137-361-11 MYLAR 330PF 5% 50V

C325 1-137-378-11 MYLAR 0.22uF 5% 50VC326 1-128-526-11 ELECT 220uF 20% 10VC327 1-137-361-11 MYLAR 330PF 5% 50VC328 1-137-361-11 MYLAR 330PF 5% 50VC329 1-137-361-11 MYLAR 330PF 5% 50V

C330 1-137-361-11 MYLAR 330PF 5% 50VC331 1-124-465-00 ELECT 0.47uF 20% 50VC333 1-124-673-11 ELECT 100uF 20% 10VC334 1-124-673-11 ELECT 100uF 20% 10VC355 1-130-495-00 MYLAR 0.1uF 5% 50V


C362 1-128-526-11 ELECT 220uF 20% 10VC367 1-136-356-11 MYLAR 470PF 5% 50VC368 1-136-356-11 MYLAR 470PF 5% 50VC381 1-126-045-11 ELECT 2.2uF 20% 50VC382 1-126-045-11 ELECT 2.2uF 20% 50V

C383 1-126-045-11 ELECT 2.2uF 20% 50VC384 1-126-045-11 ELECT 2.2uF 20% 50VC385 1-124-261-00 ELECT 10uF 20% 50VC386 1-124-261-00 ELECT 10uF 20% 50VC387 1-124-257-00 ELECT 2.2uF 20% 50V

C388 1-124-257-00 ELECT 2.2uF 20% 50VC389 1-124-257-00 ELECT 2.2uF 20% 50VC391 1-124-261-00 ELECT 10uF 20% 50VC392 1-124-261-00 ELECT 10uF 20% 50VC399 1-163-038-00 CERAMIC CHIP 0.1uF 25V

< CONNECTOR >

CN101 1-794-490-11 CONNECTOR 15PCN201 1-564-723-11 PIN, CONNECTOR (SMALL TYPE) 7PCN202 1-794-488-11 CONNECTOR

* CN203 1-564-718-11 PIN, CONNECTOR (SMALL TYPE) 2P

CN204 1-564-718-11 PIN, CONNECTOR (SMALL TYPE) 2PCN301 1-564-723-11 PIN, CONNECTOR (SMALL TYPE) 7P

* CN302 1-564-719-31 PIN, CONNECTOR (SMALL TYPE) 3P* CN303 1-564-725-11 PIN, CONNECTOR (SMALL TYPE) 9P

CN391 1-564-718-11 PIN, CONNECTOR (SMALL TYPE) 2P

CN604 1-794-489-11 CONNECTOR 26P

< DIODE >

D251 8-719-921-49 DIODE MTZJ-6.2D252 8-719-921-49 DIODE MTZJ-6.2D253 8-719-991-33 DIODE 1SS133T-77

47


D254 8-719-991-33 DIODE 1SS133T-77D304 8-719-109-97 DIODE RD6.8ESB2

D312 8-719-991-33 DIODE 1SS133T-77D316 8-719-991-33 DIODE 1SS133T-77D321 8-719-991-33 DIODE 1SS133T-77D352 8-719-991-33 DIODE 1SS133T-77D391 8-719-991-33 DIODE 1SS133T-77

< IC >

IC103 8-759-560-51 IC BU1924F (AEP, UK)IC201 8-759-476-86 IC TDA7438D013TRIC251 8-759-100-96 IC NJM4558MIC321 8-759-711-82 IC NJM4580EIC351 8-759-711-82 IC NJM4580E

IC390 8-759-332-39 IC NJM7806FAIC391 8-759-675-71 IC TA8409F

< COIL >

L101 1-410-330-11 INDUCTOR 22uH

< TRANSISTOR >

Q201 8-729-120-28 TRANSISTOR 2SC1623-L6Q202 8-729-120-28 TRANSISTOR 2SC1623-L6Q203 8-729-120-28 TRANSISTOR 2SC1623-L6Q204 8-729-120-28 TRANSISTOR 2SC1623-L6Q205 8-729-052-45 FET 2SJ461

Q301 8-729-216-22 TRANSISTOR 2SA812-T1M5Q302 8-729-141-83 TRANSISTOR 2SB1015-OQ303 8-729-120-28 TRANSISTOR 2SC1623-L6Q304 8-729-141-75 TRANSISTOR 2SD596-DV3Q305 8-729-922-34 TRANSISTOR 2SD1758F5-Q

Q306 8-729-216-22 TRANSISTOR 2SA812-T1M5Q311 8-729-216-22 TRANSISTOR 2SA812-T1M5Q312 8-729-120-28 TRANSISTOR 2SC1623-L6Q313 8-729-052-45 FET 2SJ461Q316 8-729-216-22 TRANSISTOR 2SA812-T1M5

Q317 8-729-120-28 TRANSISTOR 2SC1623-L6Q321 8-729-048-99 FET 2SK2541-TQ351 8-729-120-28 TRANSISTOR 2SC1623-L6Q352 8-729-120-28 TRANSISTOR 2SC1623-L6Q371 8-729-120-28 TRANSISTOR 2SC1623-L6

Q372 8-729-120-28 TRANSISTOR 2SC1623-L6Q373 8-729-120-28 TRANSISTOR 2SC1623-L6Q374 8-729-120-28 TRANSISTOR 2SC1623-L6Q375 8-729-422-57 TRANSISTOR DTA114ESQ376 8-729-029-66 TRANSISTOR DTC114ES

Q377 8-729-029-66 TRANSISTOR DTC114ESQ381 8-729-231-55 TRANSISTOR 2SC2878-AQ382 8-729-231-55 TRANSISTOR 2SC2878-AQ383 8-729-120-28 TRANSISTOR 2SC1623-L6Q384 8-729-120-28 TRANSISTOR 2SC1623-L6

< RESISTOR >

R142 1-249-405-11 CARBON 100 5% 1/4W(AEP, UK)

R143 1-216-025-00 RES, CHIP 100 5% 1/10W(AEP, UK)

R144 1-216-025-00 RES, CHIP 100 5% 1/10W(AEP, UK)

R145 1-216-025-00 RES, CHIP 100 5% 1/10W(AEP, UK)

R201 1-216-077-00 RES, CHIP 15K 5% 1/10W

R202 1-216-077-00 RES, CHIP 15K 5% 1/10WR203 1-216-085-00 METAL CHIP 33K 5% 1/10WR204 1-216-085-00 METAL CHIP 33K 5% 1/10WR209 1-216-089-00 RES, CHIP 47K 5% 1/10WR210 1-216-089-00 RES, CHIP 47K 5% 1/10W

R211 1-216-057-00 METAL CHIP 2.2K 5% 1/10WR212 1-216-057-00 METAL CHIP 2.2K 5% 1/10WR213 1-216-057-00 METAL CHIP 2.2K 5% 1/10WR214 1-216-057-00 METAL CHIP 2.2K 5% 1/10WR215 1-216-061-00 METAL CHIP 3.3K 5% 1/10W

R216 1-216-061-00 METAL CHIP 3.3K 5% 1/10WR217 1-216-049-00 METAL CHIP 1K 5% 1/10WR218 1-216-049-00 METAL CHIP 1K 5% 1/10WR219 1-216-121-00 METAL CHIP 1M 5% 1/10WR220 1-216-121-00 METAL CHIP 1M 5% 1/10W

R221 1-216-073-00 METAL CHIP 10K 5% 1/10WR222 1-216-073-00 METAL CHIP 10K 5% 1/10WR223 1-247-704-11 CARBON 220 5% 1/4WR225 1-216-073-00 METAL CHIP 10K 5% 1/10WR226 1-216-073-00 METAL CHIP 10K 5% 1/10W

R227 1-216-067-00 METAL CHIP 5.6K 5% 1/10WR228 1-216-067-00 METAL CHIP 5.6K 5% 1/10WR229 1-216-073-00 METAL CHIP 10K 5% 1/10WR230 1-216-073-00 METAL CHIP 10K 5% 1/10WR231 1-216-059-00 METAL CHIP 2.7K 5% 1/10W

R232 1-216-059-00 METAL CHIP 2.7K 5% 1/10WR233 1-216-067-00 METAL CHIP 5.6K 5% 1/10W

R234 1-216-067-00 METAL CHIP 5.6K 5% 1/10WR235 1-216-049-11 RES, CHIP 1K 5% 1/10WR236 1-216-049-11 RES, CHIP 1K 5% 1/10WR237 1-216-071-00 METAL CHIP 8.2K 5% 1/10WR238 1-216-071-00 METAL CHIP 8.2K 5% 1/10W

R251 1-216-089-00 RES, CHIP 47K 5% 1/10WR252 1-216-089-00 RES, CHIP 47K 5% 1/10WR253 1-216-119-00 METAL CHIP 820K 5% 1/10WR254 1-216-081-00 METAL CHIP 22K 5% 1/10WR256 1-247-704-11 CARBON 220 5% 1/4WR257 1-216-091-00 METAL CHIP 56K 5% 1/10W

R258 1-216-113-00 METAL CHIP 470K 5% 1/10WR281 1-216-057-00 METAL CHIP 2.2K 5% 1/10WR282 1-216-057-00 METAL CHIP 2.2K 5% 1/10WR302 1-247-717-11 CARBON 2.2K 5% 1/4WR303 1-216-073-00 METAL CHIP 10K 5% 1/10W

R304 1-216-073-00 METAL CHIP 10K 5% 1/10WR305 1-247-713-11 CARBON 1K 5% 1/4W

0R306 1-215-880-11 METAL OXIDE 100 5% 2W FR307 1-247-716-11 CARBON 1.8K 5% 1/4WR308 1-216-073-00 METAL CHIP 10K 5% 1/10WR309 1-216-073-00 METAL CHIP 10K 5% 1/10WR311 1-216-065-00 RES, CHIP 4.7K 5% 1/10W

R312 1-216-065-00 RES, CHIP 4.7K 5% 1/10WR313 1-216-041-00 METAL CHIP 470 5% 1/10W


Les composants identifiés par unemarque 0 sont critiques pour lasécurité.Ne les remplacer que par une pièceportant le neméro spécifié.

MAIN

48


R314 1-216-073-00 METAL CHIP 10K 5% 1/10WR315 1-216-097-00 RES, CHIP 100K 5% 1/10WR316 1-216-065-00 RES, CHIP 4.7K 5% 1/10WR317 1-216-073-00 METAL CHIP 10K 5% 1/10W

R318 1-216-065-00 RES, CHIP 4.7K 5% 1/10WR321 1-216-049-11 RES, CHIP 1K 5% 1/10WR322 1-216-049-11 RES, CHIP 1K 5% 1/10WR325 1-216-097-00 RES, CHIP 100K 5% 1/10WR326 1-216-065-00 RES, CHIP 4.7K 5% 1/10W

R327 1-216-089-00 RES, CHIP 47K 5% 1/10WR328 1-216-089-00 RES, CHIP 47K 5% 1/10WR329 1-216-113-00 METAL CHIP 470K 5% 1/10WR331 1-216-073-00 METAL CHIP 10K 5% 1/10WR332 1-216-073-00 METAL CHIP 10K 5% 1/10W

R333 1-216-073-00 METAL CHIP 10K 5% 1/10WR334 1-216-073-00 METAL CHIP 10K 5% 1/10WR351 1-216-295-00 SHORT 0R352 1-216-295-00 SHORT 0

R353 1-216-081-00 METAL CHIP 22K 5% 1/10WR354 1-216-081-00 METAL CHIP 22K 5% 1/10WR355 1-216-089-00 RES, CHIP 47K 5% 1/10WR356 1-216-089-00 RES, CHIP 47K 5% 1/10WR357 1-216-105-00 RES, CHIP 220K 5% 1/10W

R358 1-216-105-00 RES, CHIP 220K 5% 1/10WR359 1-216-295-00 SHORT 0R360 1-216-295-00 SHORT 0R361 1-216-059-00 METAL CHIP 2.7K 5% 1/10WR362 1-216-059-00 METAL CHIP 2.7K 5% 1/10W

R363 1-216-059-00 METAL CHIP 2.7K 5% 1/10WR364 1-216-059-00 METAL CHIP 2.7K 5% 1/10WR365 1-216-121-00 METAL CHIP 1M 5% 1/10WR366 1-216-121-00 METAL CHIP 1M 5% 1/10WR367 1-216-073-00 METAL CHIP 10K 5% 1/10W


R376 1-216-073-00 METAL CHIP 10K 5% 1/10WR377 1-216-113-00 METAL CHIP 470K 5% 1/10WR379 1-216-073-00 METAL CHIP 10K 5% 1/10WR381 1-216-073-00 RES, CHIP 10K 5% 1/10WR387 1-216-049-11 RES, CHIP 1K 5% 1/10W

R388 1-216-049-11 RES, CHIP 1K 5% 1/10WR389 1-216-081-00 METAL CHIP 22K 5% 1/10WR390 1-216-081-00 METAL CHIP 22K 5% 1/10WR391 1-216-049-11 RES, CHIP 1K 5% 1/10WR392 1-216-049-11 RES, CHIP 1K 5% 1/10W

R393 1-216-073-00 METAL CHIP 10K 5% 1/10WR394 1-216-065-00 RES, CHIP 4.7K 5% 1/10WR397 1-216-105-00 RES, CHIP 220K 5% 1/10WR399 1-216-073-00 METAL CHIP 10K 5% 1/10W

< SWITCH >

S391 1-554-843-11 SWITCH, SLIDE (PANEL OPEN)S392 1-572-499-21 SWITCH, TACTIL (PANEL OPEN/CLOSE)

< VIBRATOR >

X102 1-781-919-11 X TAL (4.332MHz) (AEP, UK)**************************************************************

A-4473-555-A MAIN R237 BOARD, COMPLETE**************************

< CAPACITOR >

C1 1-163-038-00 CERAMIC CHIP 0.1uF 25VC11 1-163-237-11 CERAMIC CHIP 27PF 5% 50VC12 1-163-237-11 CERAMIC CHIP 27PF 5% 50VC101 1-124-225-11 ELECT 100uF 20% 6.3VC102 1-163-038-00 CERAMIC CHIP 0.1uF 25V

C103 1-163-038-00 CERAMIC CHIP 0.1uF 25VC105 1-110-501-11 CERAMIC CHIP 0.33uF 10% 16VC106 1-163-239-11 CERAMIC CHIP 33PF 5% 50VC107 1-163-239-11 CERAMIC CHIP 33PF 5% 50VC110 1-163-038-00 CERAMIC CHIP 0.1uF 25V

C112 1-163-017-00 CERAMIC CHIP 0.0047uF 5% 50VC113 1-163-011-11 CERAMIC CHIP 0.0015uF 10% 50VC114 1-163-243-11 CERAMIC CHIP 47PF 5% 50VC115 1-163-263-11 CERAMIC CHIP 330PF 5% 50V

C116 1-163-038-00 CERAMIC CHIP 0.1uF 25VC117 1-163-263-11 CERAMIC CHIP 330PF 5% 50VC118 1-163-137-00 CERAMIC CHIP 680PF 5% 50VC119 1-163-038-00 CERAMIC CHIP 0.1uF 25VC120 1-163-021-11 CERAMIC CHIP 0.01uF 10% 50V

C121 1-107-823-11 CERAMIC CHIP 0.47uF 10% 16VC122 1-163-125-00 CERAMIC CHIP 220PF 5% 50VC123 1-163-011-11 CERAMIC CHIP 0.0015uF 10% 50VC124 1-163-809-11 CERAMIC CHIP 0.047uF 10% 25VC125 1-124-589-11 ELECT 47uF 20% 16V

C126 1-163-038-00 CERAMIC CHIP 0.1uF 25VC127 1-128-057-11 ELECT 330uF 20% 6.3VC128 1-163-038-00 CERAMIC CHIP 0.1uF 25VC129 1-163-038-00 CERAMIC CHIP 0.1uF 25VC130 1-163-229-11 CERAMIC CHIP 12PF 5% 50V

C131 1-163-229-11 CERAMIC CHIP 12PF 5% 50VC132 1-163-038-00 CERAMIC CHIP 0.1uF 25VC133 1-163-038-00 CERAMIC CHIP 0.1uF 25VC134 1-163-038-00 CERAMIC CHIP 0.1uF 25VC135 1-163-137-00 CERAMIC CHIP 680PF 5% 50V

C136 1-163-137-00 CERAMIC CHIP 680PF 5% 50VC137 1-163-137-00 CERAMIC CHIP 680PF 5% 50VC138 1-163-038-00 CERAMIC CHIP 0.1uF 25VC139 1-163-038-00 CERAMIC CHIP 0.1uF 25VC140 1-163-038-00 CERAMIC CHIP 0.1uF 25V

C141 1-124-589-11 ELECT 47uF 20% 16VC142 1-163-037-11 CERAMIC CHIP 0.022uF 10% 50VC143 1-163-137-00 CERAMIC CHIP 680PF 5% 50VC144 1-128-057-11 ELECT 330uF 20% 6.3VC145 1-163-038-00 CERAMIC CHIP 0.1uF 25V

C157 1-163-017-00 CERAMIC CHIP 0.0047uF 5% 50VC162 1-126-176-11 ELECT 220uF 20% 10VC163 1-163-038-00 CERAMIC CHIP 0.1uF 25VC164 1-163-038-00 CERAMIC CHIP 0.1uF 25VC165 1-164-348-11 CERAMIC CHIP 0.12uF 10% 25V

MAIN MAIN R237

49


C169 1-163-251-11 CERAMIC CHIP 100PF 5% 50VC401 1-126-767-11 ELECT 1000uF 20% 16VC402 1-163-038-00 CERAMIC CHIP 0.1uF 25VC403 1-124-584-00 ELECT 100uF 20% 10VC404 1-163-038-00 CERAMIC CHIP 0.1uF 25V

C405 1-126-176-11 ELECT 220uF 20% 10VC406 1-163-809-11 CERAMIC CHIP 0.047uF 10% 25VC407 1-124-242-00 ELECT 33uF 20% 25VC409 1-125-972-11 ELECT 100uF 20% 16VC411 1-125-622-11 DOUBLE LAYER 0.1F 5.5V

C413 1-163-038-00 CERAMIC CHIP 0.1uF 25VC414 1-163-038-00 CERAMIC CHIP 0.1uF 25VC417 1-124-225-11 ELECT 100uF 20% 6.3VC419 1-163-809-11 CERAMIC CHIP 0.047uF 10% 25VC422 1-163-275-11 CERAMIC CHIP 0.001uF 5% 50V

C423 1-163-809-11 CERAMIC CHIP 0.047uF 10% 25VC504 1-163-038-00 CERAMIC CHIP 0.1uF 25VC505 1-163-135-00 CERAMIC CHIP 560PF 5% 50VC506 1-163-135-00 CERAMIC CHIP 560PF 5% 50V

C509 1-163-243-11 CERAMIC CHIP 47PF 5% 50VC516 1-163-038-00 CERAMIC CHIP 0.1uF 25VC521 1-163-038-00 CERAMIC CHIP 0.1uF 25VC1041 1-127-573-11 CERAMIC CHIP 1uF 10% 16VC1042 1-127-573-11 CERAMIC CHIP 1uF 10% 16V

C1091 1-127-573-11 CERAMIC CHIP 1uF 10% 16VC1092 1-127-573-11 CERAMIC CHIP 1uF 10% 16VC1111 1-127-573-11 CERAMIC CHIP 1uF 10% 16VC1112 1-127-573-11 CERAMIC CHIP 1uF 10% 16VC5071 1-127-573-11 CERAMIC CHIP 1uF 10% 16V

C5072 1-127-573-11 CERAMIC CHIP 1uF 10% 16VC8011 1-163-255-11 CERAMIC CHIP 150PF 5% 50VC8012 1-163-255-11 CERAMIC CHIP 150PF 5% 50VC8021 1-163-137-00 CERAMIC CHIP 680PF 5% 50VC8022 1-163-137-00 CERAMIC CHIP 680PF 5% 50V

C8101 1-126-153-11 ELECT 22uF 20% 6.3VC8102 1-126-153-11 ELECT 22uF 20% 6.3V

< CONNECTOR >

* CP101 1-770-114-11 SOCKET, CONNECTOR 16PCP102 1-568-164-11 CONNECTOR, FPC (1.0MM) (ZIF) 8PCP103 1-568-165-11 CONNECTOR, FPC 22P

* CP501 1-564-709-11 PIN, CONNECTOR (SMALL TYPE) 7PCP502 1-564-707-11 PIN, CONNECTOR (SMALL TYPE) 5P

* CP503 1-564-705-11 PIN, CONNECTOR (SMALL TYPE) 3P* CP504 1-560-060-00 PIN, CONNECTOR 2P

< DIODE >

D101 8-719-400-20 DIODE MA152WA-TXD102 8-719-400-20 DIODE MA152WA-TXD401 8-719-400-20 DIODE MA152WA-TXD404 8-719-400-20 DIODE MA152WA-TXD406 8-719-400-20 DIODE MA152WA-TX

D409 8-719-400-20 DIODE MA152WA-TXD516 8-719-400-20 DIODE MA152WA-TXD517 8-719-400-20 DIODE MA152WA-TXD521 8-719-400-20 DIODE MA152WA-TXD801 8-719-400-20 DIODE MA152WA-TX

< SHORT >

J404 1-216-295-00 SHORT 0

< COIL/SHORT >

L101 1-410-509-11 INDUCTOR 10uHL102 1-469-780-11 FERRITE 0uHL103 1-469-780-11 FERRITE 0uHL401 1-216-295-00 SHORT 0L402 1-216-295-00 SHORT 0

L503 1-469-780-11 FERRITE 0uHL802 1-469-780-11 FERRITE 0uH

< TRANSISTOR >

Q101 8-729-903-46 TRANSISTOR 2SB1132-PQ102 1-801-806-11 TRANSISTOR DTC144EKA-T146Q103 8-729-027-56 TRANSISTOR DTC143TKA-T146Q401 8-729-927-50 TRANSISTOR 2SB1182-QQ402 8-729-120-28 TRANSISTOR 2SC2412K-QR

Q403 8-729-044-09 TRANSISTOR 2SD2153T100VQ404 8-729-922-34 TRANSISTOR 2SD1758F5-QRQ411 8-729-120-28 TRANSISTOR 2SC2412K-QRQ412 8-729-120-28 TRANSISTOR 2SC2412K-QRQ413 8-729-120-28 TRANSISTOR 2SC2412K-QR

Q414 8-729-922-34 TRANSISTOR 2SD1758F5-QRQ501 8-729-120-28 TRANSISTOR 2SC2412K-QRQ502 1-801-806-11 TRANSISTOR DTC144EKA-T146Q521 8-729-027-23 TRANSISTOR DTA114EKA-T146Q522 8-729-120-28 TRANSISTOR 2SC2412K-QR

Q8011 8-729-015-39 TRANSISTOR DTC323TKQ8012 8-729-015-39 TRANSISTOR DTC323TK

< RESISTOR/COIL >

R2 1-216-073-00 METAL CHIP 10K 5% 1/10WR3 1-216-073-00 METAL CHIP 10K 5% 1/10WR4 1-216-097-00 RES, CHIP 100K 5% 1/10WR5 1-216-097-00 RES, CHIP 100K 5% 1/10WR6 1-216-097-00 RES, CHIP 100K 5% 1/10W

R9 1-216-073-00 METAL CHIP 10K 5% 1/10WR10 1-216-089-00 RES, CHIP 47K 5% 1/10WR11 1-216-089-00 RES, CHIP 47K 5% 1/10WR12 1-216-089-00 RES, CHIP 47K 5% 1/10WR13 1-216-089-00 RES, CHIP 47K 5% 1/10W

R14 1-216-089-00 RES, CHIP 47K 5% 1/10WR15 1-216-041-00 METAL CHIP 470 5% 1/10WR17 1-414-234-22 INDUCTOR CHIP 0uHR18 1-216-295-00 SHORT 0R101 1-216-603-11 METAL CHIP 10 0.5% 1/10W

R102 1-216-081-00 METAL CHIP 22K 5% 1/10WR103 1-216-100-00 RES, CHIP 130K 5% 1/10WR105 1-216-072-00 METAL CHIP 9.1K 5% 1/10WR106 1-216-072-00 METAL CHIP 9.1K 5% 1/10WR109 1-216-024-00 RES, CHIP 91 5% 1/10W


MAIN R237

50


R115 1-216-073-00 METAL CHIP 10K 5% 1/10WR116 1-216-097-00 RES, CHIP 100K 5% 1/10WR117 1-216-121-00 RES, CHIP 1M 5% 1/10WR118 1-216-073-00 METAL CHIP 10K 5% 1/10WR119 1-216-061-00 METAL CHIP 3.3K 5% 1/10W

R120 1-216-107-00 METAL CHIP 270K 5% 1/10WR121 1-216-084-00 METAL CHIP 30K 5% 1/10WR122 1-216-084-00 METAL CHIP 30K 5% 1/10WR123 1-216-070-00 METAL CHIP 7.5K 5% 1/10WR124 1-216-070-00 METAL CHIP 7.5K 5% 1/10W

R125 1-216-077-00 RES, CHIP 15K 5% 1/10WR126 1-216-077-00 RES, CHIP 15K 5% 1/10WR127 1-216-070-00 METAL CHIP 7.5K 5% 1/10WR128 1-216-061-00 METAL CHIP 3.3K 5% 1/10WR129 1-216-084-00 METAL CHIP 30K 5% 1/10W

R130 1-216-084-00 METAL CHIP 30K 5% 1/10WR131 1-216-070-00 METAL CHIP 7.5K 5% 1/10WR132 1-216-070-00 METAL CHIP 7.5K 5% 1/10WR133 1-216-073-00 METAL CHIP 10K 5% 1/10WR134 1-216-109-00 METAL CHIP 330K 5% 1/10W

R135 1-216-090-00 METAL CHIP 51K 5% 1/10WR136 1-216-094-00 RES, CHIP 75K 5% 1/10WR137 1-216-070-00 METAL CHIP 7.5K 5% 1/10WR139 1-216-089-00 RES, CHIP 47K 5% 1/10WR141 1-216-073-00 METAL CHIP 10K 5% 1/10W

R142 1-216-085-00 METAL CHIP 33K 5% 1/10WR143 1-216-101-00 METAL CHIP 150K 5% 1/10WR144 1-216-081-00 METAL CHIP 22K 5% 1/10WR145 1-216-081-00 METAL CHIP 22K 5% 1/10WR158 1-216-097-00 RES, CHIP 100K 5% 1/10W

R159 1-216-085-00 METAL CHIP 33K 5% 1/10WR177 1-216-056-00 RES, CHIP 2K 5% 1/10WR179 1-216-065-00 RES, CHIP 4.7K 5% 1/10WR180 1-216-065-00 RES, CHIP 4.7K 5% 1/10WR181 1-216-081-00 METAL CHIP 22K 5% 1/10W

R194 1-216-073-00 METAL CHIP 10K 5% 1/10WR195 1-216-092-00 RES, CHIP 62K 5% 1/10WR196 1-216-081-00 METAL CHIP 22K 5% 1/10WR197 1-216-001-00 METAL CHIP 10 5% 1/10WR199 1-216-073-00 METAL CHIP 10K 5% 1/10W

R200 1-216-085-00 METAL CHIP 33K 5% 1/10WR401 1-216-037-00 METAL CHIP 330 5% 1/10WR402 1-216-091-00 METAL CHIP 56K 5% 1/10WR403 1-216-049-11 RES, CHIP 1K 5% 1/10WR404 1-216-097-00 RES, CHIP 100K 5% 1/10W

R405 1-216-073-00 METAL CHIP 10K 5% 1/10WR406 1-216-105-00 RES, CHIP 220K 5% 1/10WR407 1-216-089-00 RES, CHIP 47K 5% 1/10WR408 1-216-097-00 RES, CHIP 100K 5% 1/10WR409 1-216-097-00 RES, CHIP 100K 5% 1/10W

R411 1-216-033-00 METAL CHIP 220 5% 1/10WR412 1-216-073-00 METAL CHIP 10K 5% 1/10WR413 1-216-043-00 RES, CHIP 560 5% 1/10WR414 1-216-097-00 RES, CHIP 100K 5% 1/10WR415 1-216-097-00 RES, CHIP 100K 5% 1/10W

R416 1-216-097-00 RES, CHIP 100K 5% 1/10WR417 1-216-033-00 METAL CHIP 220 5% 1/10W

MAIN R237

R418 1-216-049-11 RES, CHIP 1K 5% 1/10WR419 1-216-105-00 RES, CHIP 220K 5% 1/10WR420 1-216-121-00 RES, CHIP 1M 5% 1/10W

R422 1-216-077-00 RES, CHIP 15K 5% 1/10WR423 1-216-037-00 METAL CHIP 330 5% 1/10WR506 1-216-073-00 METAL CHIP 10K 5% 1/10WR507 1-216-073-00 METAL CHIP 10K 5% 1/10WR508 1-216-073-00 METAL CHIP 10K 5% 1/10W


R516 1-216-075-00 METAL CHIP 12K 5% 1/10WR517 1-216-057-00 METAL CHIP 2.2K 5% 1/10WR518 1-216-097-00 RES, CHIP 100K 5% 1/10WR519 1-216-073-00 METAL CHIP 10K 5% 1/10WR524 1-216-018-00 METAL CHIP 51 5% 1/10W

R526 1-216-073-00 METAL CHIP 10K 5% 1/10WR527 1-216-065-00 RES, CHIP 4.7K 5% 1/10WR528 1-216-121-00 RES, CHIP 1M 5% 1/10WR529 1-216-065-00 RES, CHIP 4.7K 5% 1/10WR530 1-216-065-00 RES, CHIP 4.7K 5% 1/10W

R531 1-216-121-00 RES, CHIP 1M 5% 1/10WR532 1-216-065-00 RES, CHIP 4.7K 5% 1/10WR536 1-216-089-00 RES, CHIP 47K 5% 1/10WR537 1-216-089-00 RES, CHIP 47K 5% 1/10WR538 1-216-089-00 RES, CHIP 47K 5% 1/10W


R545 1-216-041-00 METAL CHIP 470 5% 1/10WR548 1-216-089-00 RES, CHIP 47K 5% 1/10WR549 1-216-073-00 METAL CHIP 10K 5% 1/10WR551 1-216-109-00 METAL CHIP 330K 5% 1/10WR552 1-216-097-00 RES, CHIP 100K 5% 1/10W

R553 1-216-095-00 METAL CHIP 82K 5% 1/10WR554 1-216-049-11 RES, CHIP 1K 5% 1/10WR563 1-216-073-00 METAL CHIP 10K 5% 1/10WR564 1-216-041-00 METAL CHIP 470 5% 1/10WR565 1-216-041-00 METAL CHIP 470 5% 1/10W

R570 1-216-034-00 METAL CHIP 240 5% 1/10WR571 1-216-019-00 METAL CHIP 56 5% 1/10WR572 1-216-027-00 METAL CHIP 120 5% 1/10WR573 1-216-023-00 METAL CHIP 82 5% 1/10WR602 1-216-033-00 METAL CHIP 220 5% 1/10W

R603 1-216-065-00 RES, CHIP 4.7K 5% 1/10WR700 1-216-049-11 RES, CHIP 1K 5% 1/10WR701 1-216-097-00 RES, CHIP 100K 5% 1/10WR702 1-216-049-11 RES, CHIP 1K 5% 1/10WR703 1-216-049-11 RES, CHIP 1K 5% 1/10W


51


MAIN R237 PHOTO JACK POWER SUPPLY


R714 1-216-049-11 RES, CHIP 1K 5% 1/10WR8011 1-216-075-00 METAL CHIP 12K 5% 1/10WR8012 1-216-075-00 METAL CHIP 12K 5% 1/10WR8021 1-216-075-00 METAL CHIP 12K 5% 1/10WR8022 1-216-075-00 METAL CHIP 12K 5% 1/10W

R8031 1-216-075-00 METAL CHIP 12K 5% 1/10WR8032 1-216-075-00 METAL CHIP 12K 5% 1/10WR8081 1-216-043-00 RES, CHIP 560 5% 1/10WR8082 1-216-043-00 RES, CHIP 560 5% 1/10WR8091 1-216-097-00 RES, CHIP 100K 5% 1/10W

R8092 1-216-097-00 RES, CHIP 100K 5% 1/10WR8101 1-216-295-00 SHORT 0R8102 1-216-295-00 SHORT 0

< CONNECTOR >

* TP101 PIN, CONNECTOR 5P

< IC >

U101 8-752-076-96 IC CXA2521AQU102 8-752-386-85 IC CXD2587QU103 8-759-082-61 IC TC4W53FUU105 8-759-675-71 IC TA8409FU106 8-759-675-71 IC TA8409F

U107 8-759-675-71 IC TA8409FU180 8-759-710-55 IC NJM2100MU401 8-759-054-12 IC PQ09RF11U404 8-759-673-97 IC BA5972FPU501 8-759-673-93 IC uPD78058FGC-A80-8BT

U502 8-759-200-79 IC TC4049BF

< VARIABLE RESISTOR >

VR102 1-237-606-11 RES, ADJ, CARBON 22K

< VIBRATOR >

X101 1-767-226-11 VIBRATOR, CRYSTAL (16.9344MHz)X501 1-577-121-11 VIBRATOR, CRYSTAL (4.194304MHz)

< DIODE >

ZD401 8-719-114-37 DIODE RD5.6JSAB2ZD402 8-719-114-50 DIODE RD7.5JSAB3ZD403 8-719-114-42 DIODE RD6.2JSAB3ZD404 8-719-114-37 DIODE RD5.6JSAB2ZD405 8-719-114-37 DIODE RD5.6JSAB2

ZD502 8-719-114-42 DIODE RD6.2JSAB3ZD503 8-719-114-42 DIODE RD6.2JSAB3ZD521 8-719-114-30 DIODE RD5.1JSAB2

**************************************************************

A-4473-562-A PHOTO JACK BOARD, COMPLETE***************************

< CAPACITOR >

C200 1-163-038-00 CERAMIC CHIP 0.1uF 25VC2001 1-163-038-00 CERAMIC CHIP 0.1uF 25V

< DIODE >

D200 8-719-991-33 DIODE 1SS133T-77

< IC >

PH200 8-749-923-04 IC TOTX178A (CD DIGITAL OUT (OPTICAL))

< RESISTOR >

R200 1-216-049-11 RES, CHIP 1K 5% 1/10WR2001 1-216-033-00 METAL CHIP 220 5% 1/10W

**************************************************************

A-4473-563-A POWER SUPPLY BOARD, COMPLETE******************************

4-229-235-01 TERMINAL PIN (K)4-229-247-01 BIND TYPE (A)4-229-249-01 PLASTIC SCREW M2.6X64-229-255-01 SCREW (3X8), TAPPING4-229-256-01 SCREW (3X6), TAPPING

7-621-773-86 SCREW +B 2.6X47-682-549-04 SCREW +B 3X107-685-546-14 SCREW +BTP 3X8 TYPE2 N-S

< CAPACITOR >

0C1 1-131-983-11 FILM 0.1uF 250V0C2 1-131-983-11 FILM 0.1uF 250V0C3 1-113-896-11 CERAMIC 220PF 10% 250V0C4 1-113-896-11 CERAMIC 220PF 10% 250V0C5 1-113-896-11 CERAMIC 220PF 10% 250V

C6 1-135-738-11 ELECT 220uF 400VC8 1-104-572-11 CERAMIC 0.0022uF 10% 2KVC9 1-162-290-31 CERAMIC 470PF 10% 50VC10 1-162-303-11 CERAMIC 0.0033uF 20% 16VC11 1-107-909-11 ELECT 47uF 20% 50V

C12 1-162-115-00 CERAMIC 330PF 10% 2KVC13 1-104-568-11 CERAMIC 470PF 10% 2KVC15 1-135-737-21 ELECT 3300uF 25VC16 1-111-044-11 ELECT 2200uF 20% 16VC17 1-126-316-51 ELECT 470uF 20% 16V

C18 1-164-159-11 CERAMIC 0.1uF 50VC20 1-164-159-11 CERAMIC 0.1uF 50VC21 1-162-600-11 CERAMIC 0.0047uF 20% 16VC22 1-111-068-11 ELECT 1500uF 20% 25V

C23 1-124-360-00 ELECT 1000uF 20% 16VC24 1-126-044-11 ELECT 1uF 20% 50VC25 1-126-335-11 ELECT 220uF 20% 10VC26 1-126-335-11 ELECT 220uF 20% 10VC27 1-104-568-11 CERAMIC 470PF 10% 2KV

C28 1-104-568-11 CERAMIC 470PF 10% 2KVC29 1-126-052-11 ELECT 100uF 20% 16VC30 1-126-052-11 ELECT 100uF 20% 16V


Les composants identifiés par unemarque 0 sont critiques pour lasécurité.Ne les remplacer que par une pièceportant le neméro spécifié.

52


C31 1-117-703-11 CERAMIC 0.0047uF 250V

< DIODE >

D1 8-719-070-53 DIODE 11E4-TA1B2D2 8-719-070-53 DIODE 11E4-TA1B2D3 8-719-070-53 DIODE 11E4-TA1B2D4 8-719-070-53 DIODE 11E4-TA1B2D5 8-719-911-19 DIODE 1SS133

D6 8-719-200-91 DIODE 11EQS10-TA1D7 8-719-200-91 DIODE 11EQS10-TA1D8 8-719-109-97 DIODE MTZJ-6.8BD9 8-719-210-21 DIODE 11EQS04D10 8-719-076-54 DIODE FSQ10A06

D11 8-719-921-75 DIODE MTZN-T-77-10BD12 8-719-924-05 DIODE MTZN-T-77-20BD13 8-719-210-21 DIODE 11EQS04D14 8-719-210-21 DIODE 11EQS04D15 8-719-210-21 DIODE 11EQS04

D16 8-719-911-19 DIODE 1SS133

< FERRITE BEAD >

FB1 1-412-473-21 FERRITE BEAD INDUCTOR

< IC >

IC1 8-749-016-64 IC STR-F6674-LF1352IC2 8-749-013-68 IC PS2561-1-DIC3 8-759-644-34 IC SEN013EIC4 8-749-013-68 IC PS2561-1-DIC5 8-759-288-53 IC LA5617

< TRANSFORMER/COIL >

0L1 1-435-466-11 LINE FILTER TRANSL2 1-419-282-11 INDUCTOR 10uHL3 1-410-525-11 INDUCTOR 220uHL4 1-410-525-11 INDUCTOR 220uH

< TRANSISTOR >

Q1 8-729-265-52 TRANSISTOR 2SC2655-YQ2 8-729-374-02 TRANSISTOR 2SA1020-YQ3 8-729-026-43 TRANSISTOR 2SA933A-RQ4 8-729-194-57 TRANSISTOR 2SC945-PQ5 8-729-194-57 TRANSISTOR 2SC945-P

Q6 8-729-050-26 TRANSISTOR 2SA1757FQ7 8-729-173-36 TRANSISTOR 2SA733-Q

< RESISTOR >

R1 1-249-426-11 CARBON 5.6K 5% 1/4WR2 1-249-415-11 CARBON 680 5% 1/4W

0R3 1-216-363-00 METAL OXIDE 0.33 5% 2W F0R4 1-215-903-11 METAL OXIDE 68K 5% 2W F

R5 1-247-895-00 CARBON 470K 5% 1/4W

R6 1-249-391-11 CARBON 6.8 5% 1/4WR7 1-247-863-11 CARBON 22K 5% 1/4WR8 1-249-422-11 CARBON 2.7K 5% 1/4WR9 1-249-419-11 CARBON 1.5K 5% 1/4WR10 1-249-401-11 CARBON 47 5% 1/4W

R11 1-249-425-11 CARBON 4.7K 5% 1/4W

R12 1-249-431-11 CARBON 15K 5% 1/4WR13 1-249-415-11 CARBON 680 5% 1/4WR14 1-249-421-11 CARBON 2.2K 5% 1/4WR15 1-249-424-11 CARBON 3.9K 5% 1/4W

R16 1-247-881-00 CARBON 120K 5% 1/4WR17 1-249-439-11 CARBON 68K 5% 1/4WR22 1-249-420-11 CARBON 1.8K 5% 1/4WR23 1-249-429-11 CARBON 10K 5% 1/4WR24 1-249-421-11 CARBON 2.2K 5% 1/4W

R25 1-249-429-11 CARBON 10K 5% 1/4W0R26 1-219-119-21 FUSIBLE 0.1 5% 1/4W F0R27 1-219-119-21 FUSIBLE 0.1 5% 1/4W F

R28 1-249-437-11 CARBON 47K 5% 1/4WR29 1-249-421-11 CARBON 2.2K 5% 1/4W

0R30 1-219-119-21 FUSIBLE 0.1 5% 1/4W F

< TRANSFORMER >

T901 1-435-160-11 TRANSFORMER, CONVERTER

< THERMISTOR >

TH1 1-803-806-31 THERMISTOR, NTC**************************************************************

1-678-387-11 POWER SW BOARD****************

< SWITCH >

S615 1-572-595-11 SWITCH, TACTILE (REFLOW TYPE) (`/1)**************************************************************

A-4473-565-A RELAY BOARD, COMPLETE**********************

< CAPACITOR >

C527 1-126-968-11 ELECT 100uF 20% 50VC544 1-126-964-11 ELECT 10uF 20% 50VC545 1-126-964-11 ELECT 10uF 20% 50VC546 1-126-959-11 ELECT 0.47uF 20% 50V

C5011 1-163-117-00 CERAMIC CHIP 100PF 5% 50VC5022 1-163-117-00 CERAMIC CHIP 100PF 5% 50V

< CONNECTOR >

* CN502 1-564-705-11 PIN, CONNECTOR (SMALL TYPE) 3PCN503 1-794-491-11 SOLDER HEADER 2P (RIGHT SPEAKER)CN504 1-794-491-11 SOLDER HEADER 2P (LEFT SPEAKER)

* CN505 1-564-708-11 PIN, CONNECTOR (SMALL TYPE) 6P

< DIODE >

D505 8-719-820-58 DIODE 1SS177D506 8-719-820-58 DIODE 1SS177D507 8-719-820-58 DIODE 1SS177D512 8-719-820-58 DIODE 1SS177D513 8-719-820-58 DIODE 1SS177

< TRANSISTOR >

Q501 8-729-401-95 TRANSISTOR 2SB945-PQ504 8-729-048-99 TRANSISTOR 2SK2541-TQ505 8-729-048-99 TRANSISTOR 2SK2541-T

POWER SUPPLY POWER SW RELAY



Ver 1.1

53


< RESISTOR >


R545 1-216-230-00 RES, CHIP 22K 5% 1/8WR546 1-216-226-00 RES, CHIP 15K 5% 1/8WR548 1-216-246-00 RES, CHIP 100K 5% 1/8WR549 1-216-270-00 RES, CHIP 1M 5% 1/8WR551 1-216-214-00 RES, CHIP 4.7K 5% 1/8W

< RELAY >

RY501 1-755-067-11 RELAY**************************************************************

A-4473-559-A TACT SW BOARD, COMPLETE************************

< CONNECTOR >

CN602 1-794-485-11 CONNECTOR 12P

< LED >

LED651 8-719-080-10 LED KM-23SGC (DISC 1)LED652 8-719-080-10 LED KM-23SGC (DISC 2)LED653 8-719-080-10 LED KM-23SGC (DISC 3)LED654 8-719-080-10 LED KM-23SGC (DISC 4)LED655 8-719-080-10 LED KM-23SGC (DISC 5)

LED656 8-719-080-09 LED KM-23SGYC (u)

< RESISTOR >

R651 1-216-025-00 RES, CHIP 100 5% 1/10WR652 1-216-025-00 RES, CHIP 100 5% 1/10WR653 1-216-025-00 RES, CHIP 100 5% 1/10WR654 1-216-025-00 RES, CHIP 100 5% 1/10WR655 1-216-025-00 RES, CHIP 100 5% 1/10W

R656 1-216-025-00 RES, CHIP 100 5% 1/10WR657 1-216-025-00 RES, CHIP 100 5% 1/10WR671 1-216-045-00 METAL CHIP 680 5% 1/10WR672 1-216-047-00 RES, CHIP 820 5% 1/10WR673 1-216-051-00 METAL CHIP 1.2K 5% 1/10W

R674 1-216-053-00 METAL CHIP 1.5K 5% 1/10WR675 1-216-057-00 METAL CHIP 2.2K 5% 1/10WR676 1-216-061-00 METAL CHIP 3.3K 5% 1/10WR677 1-216-065-00 RES, CHIP 4.7K 5% 1/10WR678 1-216-045-00 METAL CHIP 680 5% 1/10W

R679 1-216-047-00 RES, CHIP 820 5% 1/10WR680 1-216-051-00 METAL CHIP 1.2K 5% 1/10WR681 1-216-053-00 METAL CHIP 1.5K 5% 1/10WR682 1-216-057-00 METAL CHIP 2.2K 5% 1/10WR683 1-216-061-00 METAL CHIP 3.3K 5% 1/10W

R684 1-216-065-00 RES, CHIP 4.7K 5% 1/10W

< SWITCH >

S601 1-572-595-11 SWITCH, TACTIL (REFLOW TYPE) (FUNCTION)S602 1-572-595-11 SWITCH, TACTIL (REFLOW TYPE) (DISC 1)S603 1-572-595-11 SWITCH, TACTIL (REFLOW TYPE) (DISC 2)

RELAY TACT SW

S604 1-572-595-11 SWITCH, TACTIL (REFLOW TYPE) (DISC 3)S605 1-572-595-11 SWITCH, TACTIL (REFLOW TYPE) (DISC 4)

S606 1-572-595-11 SWITCH, TACTIL (REFLOW TYPE) (DISC 5)S607 1-572-595-11 SWITCH, TACTIL (REFLOW TYPE) (VOLUME +)S608 1-572-595-11 SWITCH, TACTIL (REFLOW TYPE)

(TUNER/BAND)S609 1-572-595-11 SWITCH, TACTIL (REFLOW TYPE) (u)S610 1-572-595-11 SWITCH, TACTIL (REFLOW TYPE) (x)

S611 1-572-595-11 SWITCH, TACTIL (REFLOW TYPE)(. m, TUNER -)

S612 1-572-595-11 SWITCH, TACTIL (REFLOW TYPE)(> M, TUNER +)

S613 1-572-595-11 SWITCH, TACTIL (REFLOW TYPE) (A)S614 1-572-595-11 SWITCH, TACTIL (REFLOW TYPE) (VOLUME -)

**************************************************************

MISCELLANEOUS**************

11 8-719-070-85 HAND SENSOR KU381-4017 1-792-758-11 FFC (26CORE)53 1-500-386-11 FILTER, CLAMP (FERRITE CORE)60 FFC (15CORE)61 1-693-473-21 TUNER PACK (FM/AM)

67 1-792-757-11 AC CORD (POWER)201 4-229-268-01 PCB TRA ASSY V619202 1-792-692-11 WIRE FLEXIBLE BOARD

0212 1-251-883-11 OPTICAL PICK-UP KSS-540A213 1-678-133-11 PICK-UP FLEXIBLE BOARD

D701 8-719-991-33 DIODE 1SS133T-77D702 8-719-991-33 DIODE 1SS133T-77D703 8-719-991-33 DIODE 1SS133T-77D704 8-719-991-33 DIODE 1SS133T-77D705 8-719-991-33 DIODE 1SS133T-77

D706 8-719-991-33 DIODE 1SS133T-77D707 8-719-991-33 DIODE 1SS133T-77D708 8-719-991-33 DIODE 1SS133T-77D801 8-719-070-85 DIODE KU381-4M1 1-763-519-11 MOTOR (SLED)

M2 4-229-269-01 DISC MOTOR CH ASSY (SPINDLE)M3 4-229-284-01 STC MOTOR SL ASSY (STOCKER)M4 4-229-297-01 LDG MOTOR SL ASSY (LOADING)M5 4-229-298-01 UD MOTOR SL ASSY (UP/DOWN)M391 X-4953-037-1 MOTOR PULLEY ASSY (DOOR)

************************************************************

**************HARDWARE LIST**************

#1 7-685-533-14 SCREW +BTP 2.6X6 TYPE2 N-S#2 7-685-546-14 SCREW +BTP 3X8 TYPE2 N-S#3 7-685-549-14 SCREW +BTP 3X14 TYPE2 N-S#4 7-685-535-19 SCREW +BTP 2.6X10 TYPE2 N-S#5 7-682-547-09 SCREW +B 3X6

#6 7-685-547-19 SCREW +BTP 3X10 TYPE2 N-S#7 7-682-546-04 SCREW +B 3X5#8 7-684-024-04 N 4, TYPE 2#9 7-685-872-09 SCREW +BVTT 3X8 (S)#10 7-621-770-87 SCREW +P 2.6X5

#11 7-627-553-17 PRECISION SCREW +P 2X2 TYPE3



54


HCD-LS1

#12 7-627-852-08 SCREW, PRECISION +P 1.7X2.5#13 7-621-775-08 SCREW +P 2.6X3#14 7-621-284-30 SCREW +P 2.6X8#15 7-621-259-25 SCREW +P 2.6X4

#16 7-627-850-08 SCREW, PRECISION +P 1.4X2#17 7-627-852-18 SCREW, PRECISION +P 1.7X4 TYPE3#18 7-685-546-19 SCREW +BTP 3X8 TYPE2 N-S#19 7-685-547-14 SCREW +BTP 3X10 TYPE2 N-S#20 7-685-902-11 SCREW +PWH 2.6X6

SERVICE MANUAL

HCD-LS1

SUPPLEMENT-1File this supplement with the service manual.

US ModelCanadian Model

AEP ModelUK Model

E Model

Subject: Addition and Change of Information

9-929-063-81

2002.11

2

Page Before Change After Change

Addition of Information of Destination

• PRINTED WIRING BOARD! : Indicates changed portion.

Location F – H, 6 – 8

34

10

C4

Q4

23

+

(CHASSIS)

R13

C1

C4C5

C21 C3

0C17

+L4

2

GND1 10

C4

Q4

23

+

(CHASSIS)

R13

C1

C4C5

C21 C3

0C17

+L4

2

GND1

R500

(US, CND)

#


• SCHEMATIC DIAGRAM! : Indicates changed portion.

Location H – I, 12 – 15

27

• AbbreviationCND: Canadian model

#

Location J – M, 10 – 13

#^

%

3


Location D – F, 10 – 12

31 Location G – I, 9 – 11

#^

#

Location A – C, 2 – 5

R5004.7M

F13.15A/125V (US, CND)

3.15A/250V (AEP, UK, E)

(US, CND)

^#

• AbbreviationCND: Canadian model

35



4

• EXPLODED VIEWS! : Indicates changed portion.


Ref. No. Part No. Description Remark

5 4-229-208-01 FRONT WINDOW (AEP, UK)5 4-229-758-01 FRONT WINDOW (US, Canadian, E)

9 4-233-568-01 PCB BRACKET

19 4-233-569-01 FIBER WASHER

21 4-233-570-01 LIGHT LEAK SEAL A

22 4-233-571-01 LIGHT LEAK SEAL B

not supplied

26 4-233-572-01 DOOR SPRING

28 4-233-573-01 SLIDE DOOR CUSHION

Ref. No. Part No. Description Remark

5 4-229-208-01 FRONT WINDOW

9 PCB BRACKET

19 FIBER WASHER

21 LIGHT LEAK SEAL A

22 LIGHT LEAK SEAL B

23 4-229-330-01 SHEET METAL, EARTH

26 DOOR SPRING

28 SLIDE DOOR CUSHION

37

52 A-4473-561-A MAIN BOARD, COMPLETE (AEP, UK)52 A-4473-716-A MAIN BOARD, COMPLETE (US, Canadian)52 A-4473-718-A MAIN BOARD, COMPLETE (E)

56 A-4473-563-A POWER SUPPLY BOARD, COMPLETE(AEP, UK, E)

56 A-4473-717-A POWER SUPPLY BOARD, COMPLETE(US, Canadian)

60 1-794-487-11 CONNECTOR 15P

61 1-693-407-23 TUNER PACK (FM/AM) (US, Canadian)61 1-693-473-41 TUNER PACK (FM/AM) (AEP, UK, E)

not supplied

66 4-229-258-01 BOTTOM CASE (AEP, UK)66 4-229-757-01 BOTTOM CASE (US, Canadian)66 4-229-759-01 BOTTOM CASE (E)

067 1-792-757-11 AC CORD (POWER) (AEP, UK, E)067 1-792-941-11 CORD, AC (POWER) (US, Canadian)

52 A-4473-561-A MAIN BOARD, COMPLETE

56 A-4473-563-A POWER SUPPLY BOARD, COMPLETE

60 FFC (15CORE)

61 1-693-473-21 TUNER PACK (FM/AM)

64 SLIDE KNOB PLATE

66 4-229-258-01 BOTTOM CASE

67 1-792-757-11 AC CORD (POWER)

38



19

202122notsupplied12

232526

19

202122notsupplied

not supplied

12

23

2526 $

#9

#662

63

64#9

#662

63

64not supplied @

5


Ref. No. Part No. Description RemarkRef. No. Part No. Description Remark

39119 4-233-575-01 STC SCREW GEAR SL

120 4-233-576-01 STC SCREW NUT A SL

123 4-233-577-01 STOCKER CD SL

119 STC SCREW GEAR SL

120 STC SCREW NUT A SL

123 STOCKER CD SL

40 162 4-233-574-01 UD CAM GUIDE SL162 UD CAM GUIDE SL

42 254 4-233-578-01 LOADING CHASSIS SL ASSY254 LOADING CHASSIS SL ASSY



43 0F501 1-532-465-31 FUSE (3.15A/250V) (AEP, UK, E)0F501 1-533-690-11 FUSE, GLASS CYLINDRICAL (DIA.5)

(3.15A/125V) (US, Canadian)

C620 1-124-589-11 ELECT 47uF 20% 16V

R620A 1-216-065-00 RES-CHIP 4.7K 5% 1/10W

A-4473-561-A MAIN BOARD, COMPLETE (AEP, UK)A-4473-716-A MAIN BOARD, COMPLETE (US, Canadian)A-4473-718-A MAIN BOARD, COMPLETE (E)

D304A 8-719-991-33 DIODE 1SS133T-77Q378 8-729-422-57 TRANSISTOR DTA114ES

R371 1-216-073-00 METAL CHIP 10K 5% 1/10WR372 1-216-073-00 METAL CHIP 10K 5% 1/10WR380 1-216-049-11 RES-CHIP 1K 5% 1/10W

* TP101 1-560-063-00 PIN, CONNECTOR 5P

A-4473-563-A POWER SUPPLY BOARD, COMPLETE(AEP, UK, E)

A-4473-717-A POWER SUPPLY BOARD, COMPLETE(US, Canadian)

0R500 1-219-238-11 SOLID 4.7M 20% 1/2W F(US, Canadian)

0F501 1-532-465-31 FUSE (3.15A/250V)

R607 1-216-065-00 RES-CHIP 4.7K 5% 1/10W

A-4473-561-A MAIN BOARD, COMPLETE

* TP101 PIN, CONNECTOR 5P

A-4473-563-A POWER SUPPLY BOARD, COMPLETE

44

• ELECTRICAL PARTS LIST

45

47

48

51

52

53


60 1-794-487-11 CONNECTOR 15P

61 1-693-407-23 TUNER PACK (FM/AM) (US, Canadian)61 1-693-473-41 TUNER PACK (FM/AM) (AEP, UK, E)

067 1-792-757-11 AC CORD (POWER) (AEP, UK, E)067 1-792-941-11 CORD, AC (POWER) (US, Canadian)


60 FFC (15CORE)

61 1-693-473-21 TUNER PACK (FM/AM)

67 1-792-757-11 AC CORD (POWER)



• Items marked “*” are not stocked since they are seldom required forroutine service.Some delay should be anticipated when ordering these items.

6



54

ACCESSORIES & PACKING MATERIALS*******************************

0 1-569-008-21 ADAPTOR, CONVERSION 2P (Singapore)0 1-770-019-11 ADAPTOR, CONVERSION PLUG 3P

(UK, Hong Kong)



ACCESSORIES & PACKING MATERIALS

HCD-LS1

7

HCD-LS1

MEMO

HCD-LS1

REVISION HISTORY

Clicking the version allows you to jump to the revised page.Also, clicking the version at the upper right on the revised page allows you to jump to the next revisedpage.

Ver. Date Description of Revision

1.0 2000.02 New2000.11 Supplement-1

1.1 2002.11 Correction of Part No. for D10 on POWER SUPPLY board (SPM-02107)

HCD-LS1 - SERVICE MANUAL

Documents

Transcript of HCD-LS1 - SERVICE MANUAL