Post on 24-Apr-2023
3-864-133-51(1)
1998 by Sony Corporation
CD RadioCassette-Corder
Operating Instructions
CFD-CD777SCFD-CD777L
Introduction2
WarningTo prevent fire or shock hazard, donot expose the player to rain ormoisture.
To avoid electrical shock, do not openthe cabinet. Refer servicing toqualified personnel only.
WarningDo not install the appliance in a confinedspace, such as a bookcase or built-in cabinet.
The FUNCTION selector is located at thefront.When you turn on the player, the OPR/BATTindicator lights up.
Basic O
peratio
ns
3Introduction
Table of contents
Basic Operations4 Playing a CD
6 Listening to the radio
8 Playing a tape
10 Recording on a tape
12 Dubbing
The CD Player
14 Using the display15 Locating a specific track16 Playing tracks repeatedly
(Repeat Play)17 Creating your own program
(Program Play)
The Tape Player
19 Recording through amicrophone/Using as a PAsystem
Setting Up
20 Hooking up the system23 Connecting optional components24 Adjusting the audio emphasis
(DYNAMIC SOUND SYSTEM)
Additional Information
25 Precautions27 Troubleshooting29 Maintenance30 SpecificationsBack cover
Index
Basic Operations4
Playing a CD
Basic Operations
For hookup instructions, see pages 20 – 22.
1 Set FUNCTION to CD.
2 Press 6 PUSH OPEN/CLOSEdown to open the lid of the CDcompartment and place a CDon the CD compartment.
3 Close the lid of the CDcompartment.
With the label side up
1 42,3
CD
TAPE
RADIO
TV/ LINE IN
DUBBING
FUNCTION
CD/RADIOOFF
Basic Operations
Basic O
peratio
ns
5
Display4 Press ^ (( on the remote).
The player plays all the tracksonce.
Playing timeTrack number
Use these buttons for additional operations
To Do this
adjust the volume Turn VOLUME.
stop playback Press p.
pause playback Press ^. (on the remote,press P.)Press the button again toresume play after pause.
go to the next track Press +.
go back to the previous track Press =.
remove the CD Press 6 PUSH OPEN/CLOSE.
turn off the player Set FUNCTION to TAPE•CD/RADIO OFF.
TipDuring operation, thelevel meter shows thefrequency level of thesound.Adjusting the volumewill not affect the levelmeter.
VOLUME^=, +
Level meter
FUNCTION 6 PUSH OPEN/CLOSEp
Basic Operations6
Listening to the radio
For hookup instructions, see pages 20 – 22.
1 Set FUNCTION to RADIO.
2 Set BAND to select the band youwant.
3 Turn TUNING to tune in thestation you want.
For better SW reception, use FINETUNING.
CFD-CD777S CFD-CD777L
31 2 3
CD
TAPE
RADIO
TV/ LINE IN
DUBBING
FUNCTION
CD/RADIOOFF
FM
SW2
SW1
MW
BAND
FM
MW
SW
LW
BAND
TUNING
FINE TUNING
Basic Operations
Basic O
peratio
ns
7
Use these buttons for additional operations
Tips• During operation, the
level meter shows thefrequency level of thesound.Adjusting the volumewill not affect the levelmeter.
• If the FM broadcast isnoisy, set ISS•FMMODE at the rear to“MONO”. Radio willplay in monaural.
To Do this
adjust the volume Turn VOLUME.
turn off the radio Set FUNCTION to TAPE•CD/RADIO OFF.
To improve broadcast receptionReorient the antenna for FM. Reorient the player itselffor MW or LW. For SW, extend the antenna vertically.
for FM for MW/LW
for SW
VOLUME Level meterFUNCTION
Basic Operations8
Playing a tape
For hookup instructions, see pages 20 – 22.
1 Set FUNCTION to TAPE•CD/RADIO OFF.
2 Press p6 to open tapecompartment and insert arecorded tape. Use TYPE I(normal) tape only. Close thecompartment.
3 Press PLAY (.
The player starts playing.
With the side you wantto play facing you
3 213 2
CD
TAPE
RADIO
TV/ LINE IN
DUBBING
FUNCTION
CD/RADIOOFF
STOP/EJECT
PLAY
Basic Operations
Basic O
peratio
ns
9
Use these buttons for additional operations
To Do this
adjust the volume Turn VOLUME.
stop playback Press p6.
fast-forward or rewind Press ) or 0.the tape
pause playback Press P.Press the button again toresume play after pause.
play the opposite side of Press down DIRECTIONthe tape (deck A only) once.
DIRECTION ª ·(reverse/forward) indicators show thetape direction of deck A.
eject the cassette Press p6.
To select the direction of the tape (deck A only)
To play Set DIR MODE to
both sides of the taperepeatedly
both sides of the tapefrom the front side toreverse side only*
* If play begins from the reverse side, the tape stops at theend of that side.
NoteDuring playback, do notpress ), 0 or ( onthe other deck as thiscauses excessive wowand flutter.
Tips• During operation, the
level meter shows thefrequency level of thesound.Adjusting the volumewill not affect the levelmeter.
• To play tapes in bothdecks successively,press ( on deck B andthen press PLAY and Pon deck A as the sametime. When the tapeends on deck B, theplayback startsautomatically on deckA.
DIRECTIONª · DIR MODE
0, )
0, )
p6
P
p6
P
Level meterVOLUME
Basic Operations10
Recording on a tape
Display
For hookup instructions, see pages 20 – 22.
1 Press p6 to open the tapecompartment on deck B andinsert a blank tape.
2 Select the program source youwant to record.
To record from the CD player, setFUNCTION to CD and insert aCD (see page 4).
To record from the radio, setFUNCTION to RADIO, and tunein the station you want usingBAND and TUNING (see page 6).
To record from the built-inmicrophone (MIC), setFUNCTION to TAPE•CD/RADIO OFF.
With the side you want torecord on facing you
3 1
STOP/EJECT
CD
TAPE
RADIO
TV/ LINE IN
DUBBING
FUNCTION
CD/RADIOOFF
CD
TAPE
RADIO
TV/ LINE IN
DUBBING
FUNCTION
CD/RADIOOFF
CD
TAPE
RADIO
TV/ LINE IN
DUBBING
FUNCTION
CD/RADIOOFF
2MIC
Basic Operations
Basic O
peratio
ns
11
Notes• During recording, do
not press ), 0 orPLAY on deck A as thiscauses excessive wowand flutter.
• While recording fromthe built-in microphone(MIC), no sound comesfrom the speakers or theheadphones.
• When you connect themicrophone to the MIXMIC jack, you cannotrecord from the built-inmicrophone.
Tips• Adjusting the volume or
the audio emphasis (seepage 24) will not affectthe recording level.
• If the MW/LW programmakes a whistlingsound after you'vepressed r in step 3, setthe ISS•FM MODE(Interference SuppressSwitch) at the rear to theposition that mostdecreases the noise.
• For the best results, usethe AC power as apower source.
Use these buttons for additional operations
To Press
Stop recording p6 on deck B
Pause recording P on deck BPress the button again toresume recording.
To erase a recording1 Insert the tape into deck B.2 Disconnect the audio source if connected to the TV/LINE
IN jack at the rear.3 Set FUNCTION to TV/LINE IN.4 Press r on deck B.
3 Start recording.
Press r on deck B (( isdepressed automatically).
Deck BREC
Pp6
Basic Operations12
Dubbing
For hookup instructions, see pages 20 – 22.
1 Insert a recorded tape into deck Aand a blank tape into deck B.
2 Set FUNCTION to DUBBING.
3 To dub at high speed, pressHIGH SPEED DUBBING to
ON.
To dub at normal speed, pressHIGH SPEED DUBBING to
OFF.
With the side you want torecord on facing you
2 4 114 3
STOP/EJECT
CD
TAPE
RADIO
TV/ LINE IN
DUBBING
FUNCTION
CD/RADIOOFF
HIGH SPEEDDUBBING
ONOFF
5
Basic Operations
Basic O
peratio
ns
13
4 Press P and then press PLAY on deck A.
5 Start dubbing.
Press r on deck B (( is depressedautomatically).
Deck A
Deck B
NoteDuring dubbing, do notset FUNCTION or pressHIGH SPEED DUBBINGas this causes excessivewow and flutter.
Tips• Adjusting the volume or
the audio emphasis (seepage 24) will not affectthe recording level.
• For the best results, usethe AC power as apower source.
• When the tape in deck Aends first, deck B willcontinue recording tillthe tape end. When thetape in deck B ends first,deck A plays onaccording to the settingof the DIR MODEswitch.
To stop dubbingPress p6 on deck A and B.
Use these buttons for additional operations
PLAY PAUSE
REC
p6p6
The CD Player14
Using the display
You can check information about the CDusing the display.
The CD Player
DISPLAY
Checking the total track number and playingtimeCheck the display in stop mode.
Checking the remaining timePress DISPLAY (DISPLAY/ENTER on the player)while playing a CD.
To display Press DISPLAY
remaining time on the oncecurrent track*
remaining time on the CD twiceand the number of tracks left
playing time and the current three timestrack number
* For a track whose number is more than 20, the remainingtime appears as “--:--” in the display.
Total playing time
Total track number
The CD Player 15
The C
D Player
Locating a specifictrack
You can quickly locate any track usingthe number buttons. You can also find aspecific point in a track while playing aCD.
Numberbuttons
=, +
To locate Press
a specific track directly the number button of the track.
a point while listening to + (forward) or = (backward)the sound while playing and hold down
until you find the point.
a point while observing + (forward) or = (backward)the display in pause and hold down until
you find the point.
NoteYou cannot locate aspecific track if “SHUFREP” or “PGM” is lit inthe display. Turn offthe indication bypressing p.
TipWhen you locate atrack numbered over10, press >10 first, thenthe correspondingnumber buttons.Example:To play track number23, press >10 first, then2 and 3.
The CD Player16
Playing tracksrepeatedly(Repeat Play)
You can play tracks repeatedly innormal, shuffle or program play modes(see page 17).
1 Set FUNCTION to CD on the player.
2 Press MODE (PLAY MODE on the player) untilthe repeat mode you want appears in the display.
To repeat Select
a single track REP 1
all the tracks REP ALL
tracks in random order SHUF REP
programed tracks PGM REP
3 Do either of the following to start repeat play:
• When you’ve selected REP1, select the track bypressing the number button (pressing = or+ then ^ on the player).
• When you’ve selected REP ALL or SHUF REP,press ( (^ on the player).
• When you’ve selected PGM REP, programtracks (see step 3 on page 17), then press ( (^on the player).
To cancel Repeat PlayPress MODE until “REP” disappears from the display.
TipPress and hold LOOPon the remote duringplay to repeat aselected part of a CD.When you releaseLOOP, the playerreturns to normal play.
(
MODE
Numberbuttons
The CD Player 17
The C
D Player
Creating yourown program(Program Play)
You can arrange the playing order of upto 20 tracks on a CD.
Numberbuttons
1 Set FUNCTION to CD on the player.
2 Press MODE until “PGM” appears in the display.
3 Press the number buttons for the tracks you wantto program in the order you want.
4 Press ( to start program play.
On the player1 Set FUNCTION to
CD.2 Press PLAY MODE
until “PGM” appearsin the display.
3 Press = or +then pressDISPLAY/ENTERfor the tracks youwant to program inthe order you want.
4 Press ^.
Playing order
MODE
DISPLAY
(
continued
Programed track
The CD Player18
Creating your own program (Program Play) (continued)
Tips• You can play the same
program again, sincethe program is saveduntil you open the CDcompartment or switchFUNCTION.
• The current programwill be erased if youswitch FUNCTION oropen the CDcompartment.
• You can record yourown program. Afteryou’ve created theprogram, insert a blanktape into deck B andpress r on deck B tostart recording.
To cancel Program PlayPress MODE until “PGM” disappears from thedisplay.
To check the order of tracks before playPress DISPLAY.
Every time you press the button, the track numberappears in the programed order.
To change the current programPress p once if the CD is stopped and twice if the CDis playing. The current program will be erased. Thencreate a new program following the programingprocedure.
The Tape Player 19
The Tap
e Player
Recordingthrough amicrophone/Usingas a PA system
You can record sound using amicrophone (not supplied) or useplayer as a pub
The Tape Player
TipYou can mix CD orradio sounds and recordthem by adding yourvoice or other audiothrough themicrophone.
Notes• Acoustic feedback
(howling) tend to occurwhen you use amicrophone with echofunction.
• If acoustic feed (howling) occurs, turndown the volume ormove the microphoneaway from the speakers.
Recording through a microphone
1 Plug the microphoneinto the MIX MIC jackand turn on themicrophone if it has apower switch.
2 Set FUNCTION to TAPE•CD/RADIO OFF.
3 Insert a blank tape into deck B and press r to startrecording.
Using as a PA system
1 Plug the microphone into the MIX MIC jack andturn on the microphone if it has a power switch.
2 Set FUNCTION to TV/LINE IN.
3 Sing or speak into the microphone and adjust thevolume.
MIX MIC FUNCTION r
Setting Up20
Setting Up
Hooking up thesystem
Make sure you turn off thepower before making anyconnections.
1 Hooking up the speakers
1 Align the grooves and slide the speaker box downuntil it snaps into place A.
Tips• To detach the speakers,
unlock speaker (see Bon the diagram) andslide the speaker box allthe way up and awayfrom the player.
• Connect the suppliedspeakers to this player.If you connect anyother speakers orequipment,malfunction may occur.
Rightspeaker
Left speakerSpeaker cord
AC IN
4 Batterycompartment
1 Speaker terminals
2 to a wall outlet
A
B
Setting Up 21
Setting
Up
TipOnly for thecustomers suppliedwith an AC plugadaptor:Use the supplied ACplug adaptor if theplug of the AC powercord does not matchyour outlet.
2 Connect the black wires to (–) minus and the redwires to (+) plus terminals; the right speaker wiresto the R and the left speaker wires to the Lterminals.
2 Connecting the AC power cordInsert one end of the supplied AC power cord to theAC IN socket located at the rear of the player, and theother end to the wall outlet.
CFD-CD777S only: Adjusting the voltageBe sure to set the VOLTAGE SELECTOR (at the rear)to your local power supply.
continued
Setting Up22
Hooking up the system (continued)
3 Inserting batteries into the remote
Insert two R6 (size AA) batteries (not supplied)
Replacing batteriesWith normal use, the batteries should last for about sixmonths. When the remote no longer operates theplayer, replace all the batteries with new ones.
4 Using the player on batteriesInsert eight R20 (size D) batteries (not supplied) intothe battery compartment.
To use the player on batteries, disconnect the ACpower cord from the player.
TipReplace the batterieswhen the OPR/BATTindicator dims or whenthe player stopsoperating. Replace allthe batteries with newones. Before youreplace the batteries, besure to take out the CDfrom the player.
Setting Up 23
Setting
Up
Connectingoptionalcomponents
You can enjoy the sound froma TV or VCR through thespeakers of this player.
For details, refer to theinstruction manual of thecomponent to be connected.
Before making connections, be sure to turn off thepower of each equipment, and set FUNCTION toTAPE•CD/RADIO OFF.
1 Connect a component to the player.
2 Set FUNCTION to TV/LINE IN and play theconnected component.
NoteConnect the cablesfirmly to avoid anymalfunction.
TipYou can record thesound of the connectedcomponent. Insert ablank tape, and press ron deck B.
Rear panel of thisplayer
to line out jackAudio connectingcable (not supplied)
TV, VCR,cassette player/recorder, etc.
FUNCTION TV/LINE IN
TV/LINE IN
R L
Setting Up24
Adjusting theaudio emphasis(DYNAMIC SOUND SYSTEM)
You can adjust the audio emphasis of thesound you are listening to.
Using the 5 BAND GRAPHIC EQUALIZERSlide 5 BAND GRAPHIC EQUALIZER to select theaudio emphasis you want.
Use To adjust
MEGA BASS deep bass sound
400 Hz speaking voice, middle frequencies ofinstrumental music
1 kHz presence of vocals
4 kHz brightness of sound
10 kHz high treble sounds or to reduce highfrequency noise/tape hiss
Using the PRESET MODESet the PRESET MODE selector to the sound mode youwant.
Use To
MANUAL adjust the sound using the 5 BANDGRAPHIC EQUALIZER.
DISCO get powerful, clear sounds emphasizing lowand high range audio.
PARTY get light, bright sounds emphasizing highand middle range audio.
LIVE get wide-ranging sounds having presense.
Adjusting the sound balance of the left andright speakersUse BALANCE.
NoteWhen adjusting the 5BAND GRAPHICEQUALIZER, be sureto set the PRESETMODE selector toMANUAL. Thegraphic equalizer willnot work in any otherposition.
BALANCE PRESETMODE
5 BAND GRAPHICEQUALIZER
Additional Information 25
Precautions
Additional Information
On placement• Do not leave the player in a location
near heat sources, or in a place subjectto direct sunlight, excessive dust ormechanical shock.
• Do not place the player on an inclinedor unstable place.
• Do not place anything within 10 mmof the side of the cabinet. Theventilation holes must beunobstructed for the player to operateproperly and prolong the life of itscomponents.
• If the player is left in a car parked inthe sun, be sure to choose a location inthe car where the player will not besubjected to the direct rays of the sun.
• Since a strong magnet is used for thespeakers, keep personal credit cardsusing magnetic coding or spring-wound watches away from the playerto prevent possible damage from themagnet.
On operation• If the player is brought directly from a
cold to a warm location, or is placed ina very damp room, moisture maycondense on the lens inside the CDplayer section. Should this occur, theplayer will not operate properly. Inthis case, remove the CD and waitabout an hour for the moisture toevaporate.
• If the player has not been used for along time, set it in the playback modeto warm it up for a few minutes beforeinserting a cassette.
If you have any questions or problemsconcerning your player, please consultyour nearest Sony dealer.
On safety• As the laser beam used in the CD
player section is harmful to the eyes,do not attempt to disassemble thecasing. Refer servicing to qualifiedpersonnel only.
• Should any solid object or liquid fallinto the player, unplug the player, andhave it checked by qualified personnelbefore operating it any further.
On power sources• For AC operation, check that the
player’s operating voltage is identicalwith your local power supply (see“Specifications”) and use the suppliedAC power cord; do not use any othertype. The voltage selector is located atthe rear of the player (CFD-CD777Sonly).
• The player is not disconnected fromthe AC power source (mains) as longas it is connected to the wall outlet,even if the player itself has beenturned off.
• For battery operation, use eight R20(size D) batteries.
• When the batteries are not to be used,remove them to avoid damage thatcan be caused by battery leakage orcorrosion.
• The nameplate indicating operatingvoltage, power consumption, etc. islocated at the rear.
continued
Additional Information26
Notes on CDs• Before playing, clean the CD with a
cleaning cloth. Wipe the CD from thecenter out.
• Do not use solvents such as benzine,thinner, commercially availablecleaners or anti-static spray intendedfor vinyl LPs.
• Do not expose the CD to directsunlight or heat sources such as hotair ducts, nor leave it in a car parkedin direct sunlight as there can be aconsiderable rise in temperatureinside the car.
• Do not stick paper or sticker on theCD, nor scratch the surface of the CD.
• After playing, store the CD in its case.
If there is a scratch, dirt or fingerprintson the CD, it may cause tracking error.
Notes on cassettes• Break off the cassette tab from side A
or B to prevent accidental recording. Ifyou want to reuse the tape forrecording, cover the broken tab withadhesive tape.
• The use of a cassette with more than90 minutes of play time is notrecommended except for long,continuous recording or playback.
Side A
Tab for side ATab for side B
Precautions (continued)
Additional Information 27
Troubleshooting
Remedy
• Connect the AC power cord to a wall outletsecurely.
• Make sure the batteries are inserted correctly.
• Set FUNCTION to the position you want tooperate.
• Adjust the volume.• Unplug the headphones when listening through
speakers.
• Insert the CD with the label surface up.
• Make sure that the CD compartment is closed.• Place the CD with the label surface up.• Clean the CD.• Take out the CD and leave the CD compartment
open for about an hour to dry moisturecondensation.
• Set FUNCTION to CD.
• Reduce the volume.• Clean the CD, or replace it if the CD is badly
damaged• Place the player in a location free from
vibration.
• Replace all the batteries with new ones if theyare weak.
• Move the player away from the TV.• If you are using the remote while listening to
MW/LW radio, noise may be heard. This isunavoidable.
• If you are listening to an FM program near theTV with an indoor antenna, move the playeraway from the TV.
Gen
eral
Symptom
The power is not on.
There is no audio.
“no disc“ lights in the display evenwhen a CD is in place.
The CD does not play.
The sound drops out.
The audio is weak or has poorquality.
The picture of your TV becomesunstable.
CD
Pla
yer
Rad
io
continued
Additional Information28
Remedy
• Close the tape compartment securely.
• Make sure the safety tab on the cassette is inplace.
• Make sure FUNCTION is set to “TAPE” or“DUBBING”.
• Clean the erasing head (see page 29.)• Replace all the batteries with new ones if they
are weak.
• Make sure the tape is inserted properly.• Make sure the safety tab of the cassette is in
place.
• Clean the heads, pinch rollers and capstans (Seepage 29).
• Demagnetize the heads using a demagnetizer(see page 29).
• The TYPE II (high position) or TYPE IV (metal)tape is being used. Use TYPE I (normal) tapeonly.
• Replace all the batteries in the remote with newones if they are weak.
• Make sure that you are pointing the remote atthe remote sensor on the player.
• Remove any obstacles in the path of the remoteand the player.
• Make sure the remote sensor is not exposed tostrong light such as direct sunlight orfluorescent lamp light.
• Move closer to the player when using theremote.
Tap
e Pl
ayer
Symptom
The tape does not move when youpress an operation button.
The REC r button does notfunction/The tape does not play.
The tape does not erase completely.
The tape does not record.
The audio is weak/The audioquality is poor.
The sound is distorted.
The remote does not function.
Troubleshooting (continued)R
emo
te
After trying the above remedies, if the player still does not function properly, unplug the ACpower cord and remove all the batteries. After all the indications in the display disappear, plugthe power cord and insert the batteries again. If the problem persists, please consult your nearestSony dealer.
Additional Information 29
Maintenance
After cleaning, insert a tape when theareas cleaned are completely dry.
Demagnetizing the tape headsAfter 20 to 30 hours of use, enoughresidual magnetism will have built upon the tape heads to begin to cause lossof high frequency sound and hiss. Atthis time, you should demagnetize theheads and all metal parts in the tapepath with a commercially available tapehead demagnetizer.
Cleaning the cabinetClean the cabinet, panel and controlswith a soft cloth slightly moistened witha mild detergent solution. Do not useany type of abrasive pad, scouringpowder, or solvent, such as alcohol orbenzine.
Cleaning the lensIf the lens becomes dirty, it may cause askipping of sound during CD operation.Clean with a commercially availableblower.
Cleaning the tape heads and tapepathWipe the heads, the pinch rollers andthe capstans with a cleaning swabslightly moistened with cleaning fluid oralcohol after every 10 hours of operationfor optimum playback and recordingquality. To make the best possiblerecording, however, we recommend thatyou clean all surfaces over which tapetravels before each recording.
Capstan
Pinch roller
Lens
Erase head
Capstan
Pinch roller
Record/Playbackhead
Playback head
Deck A
Deck B
Additional Information30
Specifications
CD player sectionSystem
Compact disc digital audio systemLaser diode properties
Material: GaAlAsWave length: 780 nmEmission duration: ContinuousLaser output: Less than 44.6 µW(This output is the value measured at a distance ofabout 200 mm from the objective lens surface onthe optical pick-up block with 7 mm aperture.)
Spindle speed200 r/min (rpm) to 500 r/min (rpm) (CLV)
Number of channels2
Frequency response20 - 20,000 Hz +0/–1.5 dB
Wow and flutterBelow measurable limit
Radio sectionFrequency range
CFD-CD777S
FM Saudi arabia 87.6 - 107 MHzOther countries 87.6 - 108 MHz
MW 530 - 1,605 kHz
SW1 2.3 - 7 MHz
SW2 7 - 22 MHz
CFD-CD777L
FM 65.0 - 108 MHz
MW 531 - 1,602 kHz
LW 153 - 279 kHz
SW 5.95 - 18 MHz
IFFM: 10.7 MHzSW/MW/LW: 455 kHz
AntennasFM/SW: Telescopic antennaMW/LW: Built-in ferrite bar antenna
Cassette-corder sectionRecording system
4-track 2 channel stereoFast winding time
Approx. 120 s (sec.) with Sony cassette C-60Frequency response
TYPE I (normal): 80 - 12,500 Hz
GeneralSpeaker
Woofer: 10 cm (4 in.) dia., 4 ohms, cone type (2)Tweeter: 5 cm (2 in.) dia.,
OutputsHeadphones jack (stereo minijack)For 16 - 68 ohms impedance headphones
Maximum power output12 W + 12 W
Power requirementsFor CD radio cassette-corder:
CFD-CD777S
110 - 120, 220 - 240 V AC selectable, 50/60 Hz
CFD-CD777L
230 V AC, 50 Hz
12 V DC, 8 R20 (size D) batteriesFor remote control:3 V DC, 2 R6 (size AA) batteries
Power consumptionAC 47 W
Battery lifeFor CD radio cassette-corder:
FM recording
Sony R20P: approx. 4 h
Sony alkaline LR20: approx. 9 h
Tape playback
Sony R20P: approx. 2 h
Sony alkaline LR20: approx. 4 h
CD playback
Sony R20P: approx. 1.5 h
Sony alkaline LR20: approx. 3 h
Additional Information 31
DimensionsApprox. 761 × 245 × 258 mm(w/h/d) (30 × 9 3⁄4 × 10 1⁄4 inches)(incl. projecting parts)
MassApprox. 9.5 kg (20 lb. 15 oz) (incl. batteries)
Supplied accessoryAC power cord (1)Remote control (1)
Design and specifications are subject to change withoutnotice.
Optional accessoriesSony MDR headphone series
Additional Information32
Index
AAudio emphasis 24
BBALANCE 24Batteries
for player 22for remote 22
CCD player 14Cleaning
cabinet 29lens 29tape heads and tapepath 29
ConnectingAC power cord 21optional components 23
Creating your own program17
D, E, FDemagnetizing the tapeheads 29Display 14Dubbing 12
G, HGRAPHIC EQUALIZER 24
I, J, KImproving broadcastreception 7
LListening to the radio 6Locating a specific track 15
M, N, OMEGA BASS 24
P, QPA system 19Playing
a CD 4a tape 8tracks repeatedly 16
PRESET MODE 24Program Play 17Public address systemSee PA system.
RRecording
on a tape 10Repeat Play 16
SSelecting
audio emphasis 24tracks 15
Setting up 20
TTroubleshooting 27
UUsing
the display 14
V, W, X, Y, ZVOLTAGE SELECTOR 21
Sony Corporation Printed in Indonesia