1/30/2017
1
Turning Operations
Lec4-1Fundamentals of machining and machine tools - Isfahan Uni. of Tech.
Lec4-2
Turning Operations
• Longitudinal turning
• Facing
• Knurling
• Boring
• Taper Turning
• Eccentric Turning
• Chamfering
• Cut-off
• Grooving
• Contour turning
• Grinding
• Threading
Fundamentals of machining and machine tools - Isfahan Uni. of Tech.
1/30/2017
2
Lec4-3
Turning Operations
Facing Taper turningContour turning
Form turning
Chamfering Cutoff Threading
Boring Drilling Knurling
Fundamentals of machining and machine tools - Isfahan Uni. of Tech.
Lec4-4
Longitudinal Turning
Fundamentals of machining and machine tools - Isfahan Uni. of Tech.
1/30/2017
3
tool
5
Longitudinal Turning
• Small overhang
• Tool offset
• Easier cutting, less vibration and noise
• h=0.04 x R
• hmax=0.5 mm
Lec4-5
tool
h R
Fundamentals of machining and machine tools - Isfahan Uni. of Tech.
Lec4-6
Longitudinal Turning
• Main cutting edge
• Right hand
• Left hand
• Neutral
Right-hand Left-handneutral
Fundamentals of machining and machine tools - Isfahan Uni. of Tech.
1/30/2017
4
Lec4-7
Facing
• Feed in the radial direction
• Tool tip on the workpiece center
• Direction of tool motion depends on the main cutting edge
Fundamentals of machining and machine tools - Isfahan Uni. of Tech.
Lec4-8
Facing
Fundamentals of machining and machine tools - Isfahan Uni. of Tech.
1/30/2017
5
Lec4-9
Knurling
• Regularly shaped roughness on cylindrical surfaces
• For Decorative and/or Functional Purpose
• Knurling Tool
• A Forming Process
• MRR~0
• Too much heat -> coolant
• Workpiece diameter increases
Fundamentals of machining and machine tools - Isfahan Uni. of Tech.
Lec4-10
Knurling
Fundamentals of machining and machine tools - Isfahan Uni. of Tech.
1/30/2017
6
Lec4-11
Knurling
Fundamentals of machining and machine tools - Isfahan Uni. of Tech.
Lec4-12
Knurling
Fundamentals of machining and machine tools - Isfahan Uni. of Tech.
1/30/2017
7
Lec4-13
Taper
• Rapid and accurate method of aligning machine parts
• Easy method of holding tools
• Taper is expressed as change of diameter per unit of length
• Inch system usually expressed in taper per foot (tpf)
D=inch , d=inch , L=inch
L
dD
k
1
L
D d α
L
dDtpf
.12
Fundamentals of machining and machine tools - Isfahan Uni. of Tech.
Lec4-14
Taper Calculations: TPF
in per foot
L
dDtpf
12
1 3
1 1.250tpf
.12
Fundamentals of machining and machine tools - Isfahan Uni. of Tech.
1/30/2017
8
Lec4-15
Metric Tapers
• Expressed as ratio of 1 mm per unit of length
Work would taper 1 mmin a distance of 20 mm
ratio of 1:20
Fundamentals of machining and machine tools - Isfahan Uni. of Tech.
Lec4-16
Machine Tapers
• Classified by American Standards Association
• Self-holding tapers
• Steep or self-releasing tapers
Fundamentals of machining and machine tools - Isfahan Uni. of Tech.
1/30/2017
9
Lec4-17
Self-Holding Tapers
• Remain tight in position
• Most common forms
• Morse, the Brown & Sharpe, .750-in.-per-ft taper
• Smaller sizes provided with tang to help drive the cutting tool
• Larger sizes employ tang drive with shank held in by key or key drive with shank held draw bolt
Fundamentals of machining and machine tools - Isfahan Uni. of Tech.
Lec4-18
Steep Tapers
• 3.500 in. taper per foot (tpf)
• Formerly called standard milling machine taper
• Used mainly for alignment of milling machine arbors and accessories
• Has key drive and uses draw-in bolt to hold it securely in milling machine spindle
Fundamentals of machining and machine tools - Isfahan Uni. of Tech.
1/30/2017
10
Lec4-19
Standard Tapers
• Morse taper• Approximately 0.625-in tpf, eight sizes #0 to #7
• Used for drills, reamers, and lathe center shanks
• Brown & Sharpe taper• 0.502-in. tpf, sizes from #4 to #12
• Used on Brown and Sharpe machines
• Jarno taper• 0.600-in. tpf, sizes from #2 to #20
• Standard taper pins• Used for positioning and holding parts together
• ¼ tpf, standard sizes range from #6/0 to #10
Fundamentals of machining and machine tools - Isfahan Uni. of Tech.
Lec4-20
Taper Turning
• Swiveling the compound rest
• Offsetting tailstock
• Taper attachment
• Method used depends on work length, taper length, taper angle and number of pieces
Fundamentals of machining and machine tools - Isfahan Uni. of Tech.
1/30/2017
11
Lec4-21
Taper Turning Using Compound Rest
1. Calculate the taper angle
2. Loosen compound rest lock screws
3. Swivel compound rest as follows:
Fundamentals of machining and machine tools - Isfahan Uni. of Tech.
Lec4-22
Taper Turning Using Compound Rest
4. Tighten compound rest lock screws
5. Set cutting tool to center with toolholder at right angles to taper to be cut
6. Tighten tool-post securely
7. Back off top slide of compound rest so there will be enough travel to machine length of taper
Fundamentals of machining and machine tools - Isfahan Uni. of Tech.
1/30/2017
12
Lec4-23
Taper Turning Using Compound Rest
8. Move carriage to position cutting tool near start of taper and then lock carriage
9. Rough turn taper by feeding cutting tool using compound rest feed handle
10.Check taper for accuracy and read just compound rest setting if necessary
11.Finish-turn and check taper for size and fit
Fundamentals of machining and machine tools - Isfahan Uni. of Tech.
Lec4-24
Taper Turning Using Compound Rest
Fundamentals of machining and machine tools - Isfahan Uni. of Tech.
1/30/2017
13
Lec4-25
Taper Turning Using Compound Rest
• Short or large angle tapers
• Tool fed by hand -> not very good surface finish
• Internal and external tapers
• Angle
• Tapered mandrels
• Reading on the machine
Fundamentals of machining and machine tools - Isfahan Uni. of Tech.
Lec4-26
Taper Turning Using Tailsotck Offset
• Loosen the tailstock clamp nut
• Offset upper part of tailstock by loosening the screw
S
lα/2
l
dD
2)
2tan(
2
dDS
l
S)
2sin(
Small angle
Fundamentals of machining and machine tools - Isfahan Uni. of Tech.
1/30/2017
14
Lec4-27
Taper Turning Using Tailsotck Offset
l
dD
2)
2tan(
L
S)
2sin(
l
dDLS
2
Small angle
50max
LS
Fundamentals of machining and machine tools - Isfahan Uni. of Tech.
Lec4-28
Taper Turning Using Tailsotck Offset
• Generally used when no taper attachment available
• Involves moving tailstock center out of line with headstock center
• Amount tailstock may be offset limited
• Small taper angles (<3°)
• Only external tapers
• Time consuming
Fundamentals of machining and machine tools - Isfahan Uni. of Tech.
1/30/2017
15
Lec4-29
Taper Turning Using Tailsotck Offset
Fundamentals of machining and machine tools - Isfahan Uni. of Tech.
Lec4-30
Taper Turning Using Tailsotck Offset
Fundamentals of machining and machine tools - Isfahan Uni. of Tech.
1/30/2017
16
Lec4-31
Taper Turning Using Tailsotck Offset
Fundamentals of machining and machine tools - Isfahan Uni. of Tech.
Lec4-32
Taper Turning Using Taper Attachments
• The amount guide bar set over is one-half angle given on drawing
• Cross slide is attached to guide bar
• Remove binding screw that holds cross-slide to cross-feed screw nut
Fundamentals of machining and machine tools - Isfahan Uni. of Tech.
1/30/2017
17
Lec4-33
Taper Turning Using Taper Attachments
• Simple setup
• Easy to change from taper to parallel turning with no time lost to align centers
• No limit on the work length
• Lathe centers remain in alignment, preventing distortion of centers
• Work can be tightly held between centers, in chuck or in collet
• Internal and external
• Automatic feed -> good surface finish
Fundamentals of machining and machine tools - Isfahan Uni. of Tech.
Lec4-34
Taper Turning Using Taper Attachments
Fundamentals of machining and machine tools - Isfahan Uni. of Tech.
1/30/2017
18
Lec4-35
Eccentrics
• Shaft that may have two or more turned diameters parallel to each other
• Not concentric with normal axis of work
• Used in locking devices, in feed mechanism on some machines, and in crankshaft of automobiles
• Where necessary to convert rotary motion into reciprocating motion
Fundamentals of machining and machine tools - Isfahan Uni. of Tech.
Lec4-36
Eccentrics
• Amount of eccentricity (throw) is distance set of center holes has been offset from normal work axis
• If center holes offset .250 in. from work axis, amount of throw would be .250 in and total travel of eccentric would be .500 in.
Fundamentals of machining and machine tools - Isfahan Uni. of Tech.
1/30/2017
19
Lec4-37
Eccentric Turning
• Adjustable three-jaws chuck
Fundamentals of machining and machine tools - Isfahan Uni. of Tech.
Lec4-38
Eccentric Turning
• Auxiliary part
• Fixture
• Faceplate
Fundamentals of machining and machine tools - Isfahan Uni. of Tech.
1/30/2017
20
Lec4-39
Eccentric Turning
• Mandrel for hollow shafts
Fundamentals of machining and machine tools - Isfahan Uni. of Tech.
Lec4-40
Procedure to Turn Eccentric
1. Place work in chuck and face it to length
2. Place work in V-block on surface plate
3. Set vernier height gage to top of work and note reading
4. Subtract half work diameter from reading and set gage to this dimension
5. Scribe centerline on both ends of work
6. Rotate work 90° and scribe another centerline on both ends at same height-gage setting
Fundamentals of machining and machine tools - Isfahan Uni. of Tech.
1/30/2017
21
Lec4-41
Procedure to Turn Eccentric
Fundamentals of machining and machine tools - Isfahan Uni. of Tech.
Lec4-42
Procedure to Turn Eccentric
7. Lower or raise height-gage as much as the amount of eccentricity and scribe lines for offset centers on both ends
8. Carefully center-punch four scribed centers and drill center holes in each end
9. Mount work in lathe and turn diameter with true centers
10.Set work on offset centers and turn eccentric (center section) to required diameter
Fundamentals of machining and machine tools - Isfahan Uni. of Tech.
1/30/2017
22
Lec4-43
Eccentric Turning
Fundamentals of machining and machine tools - Isfahan Uni. of Tech.
Lec4-44
Eccentric Turning
Fundamentals of machining and machine tools - Isfahan Uni. of Tech.
1/30/2017
23
Lec4-45
Chamfering
• Cutting edge cuts an angle on the corner of the cylinder, forming a "chamfer"
Fundamentals of machining and machine tools - Isfahan Uni. of Tech.
Lec4-46
Grooving
• Tool feed in the radial direction
• Groove width equal to cutting tool width
• Multiple cuts for grooves larger than the tool width
• Internal and external
Fundamentals of machining and machine tools - Isfahan Uni. of Tech.
1/30/2017
24
Lec4-47
Grooving
Fundamentals of machining and machine tools - Isfahan Uni. of Tech.
Lec4-48
Grooving
Fundamentals of machining and machine tools - Isfahan Uni. of Tech.
1/30/2017
25
Lec4-49
Parting-off
• Similar to grooving
• Tool in the radial direction
Fundamentals of machining and machine tools - Isfahan Uni. of Tech.
Lec4-50
Parting-off
Fundamentals of machining and machine tools - Isfahan Uni. of Tech.
1/30/2017
26
Lec4-51
Threading
• Pointed form tool
• Axial feed
• Large feed rate
• Specified length and pitch
• May require multiple passes
• Will be later discussed in detail
Fundamentals of machining and machine tools - Isfahan Uni. of Tech.
Lec4-52
Threading
Fundamentals of machining and machine tools - Isfahan Uni. of Tech.
1/30/2017
27
Lec4-53
Contour Turning
• Tool follows a contour that is other than straight
• Contour attachment
• Copying lathe
Fundamentals of machining and machine tools - Isfahan Uni. of Tech.
Lec4-54
Drilling
• Drill is fixed in the tailstock
• Workpiece rotates
• Tailstock hand-wheel is used to feed the drill
Fundamentals of machining and machine tools - Isfahan Uni. of Tech.
1/30/2017
28
Lec4-55
Drilling
1. Center drill
Fundamentals of machining and machine tools - Isfahan Uni. of Tech.
Lec4-56
Drilling
2. Twist drill
Fundamentals of machining and machine tools - Isfahan Uni. of Tech.
1/30/2017
29
Lec4-57
Boring
• Axial feed of boring tool
• Along an internal surface
• Form different features, such as steps, tapers, chamfers, and contours
• After drilling a hole
Fundamentals of machining and machine tools - Isfahan Uni. of Tech.
Lec4-58
Reaming
• Reamer is fixed in the tailstock and fed axially
Fundamentals of machining and machine tools - Isfahan Uni. of Tech.
1/30/2017
30
Lec4-59
Tapping
• Tap is fixed in the tailstock and moved along the workpiece axis
Fundamentals of machining and machine tools - Isfahan Uni. of Tech.
Lec4-60
Sequence of Operations to Turn a Pin
Fundamentals of machining and machine tools - Isfahan Uni. of Tech.
1/30/2017
31
Lec4-61
Sequence of Operations to Turn a Pin
Fundamentals of machining and machine tools - Isfahan Uni. of Tech.
Lec4-62
Some Advanced Turning Techniques
Fundamentals of machining and machine tools - Isfahan Uni. of Tech.
1/30/2017
32
Lec4-63
MDT
• Multi Direction Turning
• Turning
• Profiling
• Grooving
• Threading
• Parting-off
Fundamentals of machining and machine tools - Isfahan Uni. of Tech.
Lec4-64
MDT
• Applications
Fundamentals of machining and machine tools - Isfahan Uni. of Tech.
1/30/2017
33
Lec4-65
MDT
Fundamentals of machining and machine tools - Isfahan Uni. of Tech.
Lec4-66
MDT
2
31
231
2
3
1
Fundamentals of machining and machine tools - Isfahan Uni. of Tech.
1/30/2017
34
Lec4-67
MDT
Fundamentals of machining and machine tools - Isfahan Uni. of Tech.
Lec4-68
Plunge Turning
• Saving time
• Improve surface integrity
Conventional Turning Plunge Turning
Fundamentals of machining and machine tools - Isfahan Uni. of Tech.
1/30/2017
35
Lec4-69
Plunging
Single point Plunge
• Potential with Plunge- High productivity
- Improved surface integrity
• Limitation with Plunge- Dimensional & form accuracy
- Flexibility
- No standard solution
Fundamentals of machining and machine tools - Isfahan Uni. of Tech.
Lec4-70
Capto
Fundamentals of machining and machine tools - Isfahan Uni. of Tech.