VacuFlush-HTS-models.pdf - Stroboflash

1

HOLDING TANK SYSTEMOWNER’S MANUAL

VacuFlush® 10HTS, 18HTS, 35HTS and 42HTS Models;Standard 28HTS and 40HTS Models

Dometic Corporation • Sanitation Systems13128 State Rt. 226, P.O. Box 38Big Prairie, OH 44611-0038 USA

330-496-32111-800-321-9886 • Fax: 330-496-3097

® Registered; ™ Trademark of Dometic Corporation© Dometic Corporation

This manual must be read and under-stood before installation, adjustment,service, or maintenance is performed.Modification of this product canresult in property damage.

WARNING!

2

FEATURES

TABLE OF CONTENTS

SeaLand’s standard 28 and 40 Holding Tank System (HTS) models feature a space-saving design thatcombines the level indicator, vent filter, overboard discharge pump (optional) and TankSaver vacuum reliefvalve into one package.VacuFlush models 10HTS, 18HTS, 35HTS and 42HTS include vacuum generator, level indicator and Tank-Saver vacuum relief valve. Models 35HTS and 42HTS also include a vent filter and overboard dischargepump (optional).HTS technology simplifies installation and assures quality by assembling and testing all components at thefactory. Integral mounting feet eliminate all strapping. Separate connections are provided to the overboarddischarge and dockside fittings.Each HTS exceeds proposed ISO standard with 95% removal of tank contents. Tank material is 5/16-inch[7.9mm] durable linear low density polyethylene (LLDPE) with no seams to leak. All penetrations are locatedabove highest level of tank contents.The TankWatch level indicator cap has three floats that are adjusted to indicate when tank is empty, midrange and full. The HTS can also be used with the optional TankWatch 4 level indicator panel which desig-nates the level of the tank contents.SeaLand’s SaniGardTM holding tank vent filter contains odor-removing media which eliminate odors from thetank vent. Each cartridge is good for one boating season and is easily replaced. Filter sold separately from10-gallon and 18-gallon HTS.The SaniPumpTM T-series overboard discharge pump will empty a tank at a rate of 3.9 gpm [14.7 liters/minute],can run dry without harming the pump, and is self priming.The 1 ½" TankSaver valve provides an excellent odor seal and meets the ISO standard on venting require-ments. The TankSaver valve will protect the holding tank from excessive suction by dockside pumps.

Note: Spindles not supplied with 18HTS.1. Avoid mounting the holding tanks next to extreme heat sources, such as engine manifolds.2. Mount to surface supporting the entire area of the tank. Avoid mounting tank on projections such as

fastener heads, which could puncture the tank.3. Secure the tank as indicated below.

INSTALLATION INSTRUCTIONS

Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2Installation Instructions . . . . . . . . . . . . . . . . . 2 - 4Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4Winterizing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . 5Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 - 7Parts Lists . . . . . . . . . . . . . . . . . . . . . . . . . . 8 - 15

HTS Components . . . . . . . . . . . . . . . . . . . . . . . 16VacuFlush® Vacuum Generators . . . . . . . . . . . . 17Other HTS Features . . . . . . . . . . . . . . . . . . . . . 17Holding Tank Discharge Information . . . . . . . . . 18Customer Service . . . . . . . . . . . . . . . . . . . . . . . 19Manufacturer's One-Year Limited Warranty . . . 20

3

INSTALLATION INSTRUCTIONS (cont’d)Secure 5/8" vent hose, 1 ½" holding tank inlet hose, 1 ½" dockside discharge hose, and 1 ½" overboarddischarge pump hose (optional). SeaLand recommends that all 1 ½" hoses be secured with double clamps toprevent any leaks that may occur if the fittings are undersized.

4

WINTERIZINGIf using the HTS with SeaLand’s VacuFlush components, refer to VacuFlush Owner’s Manual for winterizationinstructions. If using antifreeze to winterize the HTS, use only propylene glycol freshwater antifreeze that doesnot contain alcohol. Antifreeze that contains alcohol will result in damage to your sanitation system.1. Pump out holding tank.2. Thoroughly flush the system with fresh water before adding propylene glycol freshwater antifreeze to the

HTS.3. Turn off electrical power.

CLEANINGA small amount of water remains in all marine holding tanks. It is good practice to rinse the tank after thecontents have been discharged. This can be accomplished by adding water to the toilet bowl. Add 8 ounces(237ml) of SeaLand Holding Tank Deodorant and Cleaner to the bowl. Flush the entire contents into theholding tank and continue flushing until the discharge from the holding tank is clear.Do not use chlorine-based cleaners, caustic cleaners or chemicals, such as drain-opening products, asthey may damage the system’s seals and hose.

INSTALLATION INSTRUCTIONS (cont’d)

5

SPECIFICATIONS

10HTS

18HTS

28HTS

35HTS

40HTS

42HTS

10 Gallons38 Liters

18 Gallons68 Liters

28 Gallons106 Liters35 Gallons132 Liters40 Gallons151.4 Liters42 Gallons159 Liters

36 Lbs.16.3 Kg39 Lbs.17.7 Kg40 Lbs.18 Kg

58 Lbs.26.3 Kg44 Lbs.20 Kg

70 Lbs.32 Kg

116 Lbs.52.6 Kg183 Lbs.

83 Kg268 Lbs.121.5 Kg338 Lbs.153 Kg

380 Lbs.172 Kg

410 Lbs.186 Kg

.5 Gallons1.9 Liters

1.5 Gallons5.6 Liters.8 Gallons

3 Liters1.0 Gallons3.8 Liters

1.6 Gallons6 Liters

1.6 Gallons6 Liters

28

50

82

105

117

123

Number ofFlushes*

ResidualCapacityMax. WeightEmpty

WeightCapacitySizeLength x Width x HeightModel

32 3/8" x 10 3/4" x 16 1/2"822mm x 273mm x 419mm

29" x 15 ½" x 22 1/8"737mm x 394mm x 562mm

30" x 19" x 19 ½"762mm x 483mm x 495mm

32" x 22 ½" x 21 ½"813mm x 572mm x 546mm

35" x 21" x 20"889mm x 533mm x 508mm

43" x 18" x 25"1092mm x 457mm x 635mm

* VacuFlush toilets use as little as 0.11 gal. (0.4 l) of water per flush. Because we recommend adding more water when flushingsolids, we conservatively estimate average water use at 0.2 gal. (0.76 l) per flush. Total effluent averages .34 gal. (1.29 l) perflush. For HTS units with Discharge Pump, add 9 lbs. (4.1 Kg) to Empty Weight.

6

WIRING

Overboard DischargePump

Overboard Discharge Pumpwith SeacockInterlock Relay& DeutschConnectors

Vacuum Generator

Tank Level Monitor

PLEASE NOTE THAT THE RECESSED SHOULDER OFTHE FLOAT IS DOWNWARD ON THE EMPTY FLOAT.

7

WIRING (cont’d)

10HTS, 18HTS, 35HTSwith Shutdown Relay

8

123456789101112

600342806385310767600343023600343758600342766600342238600343657600342958600340423600340424385310768600344258

1 ½" MPT x 90º Elbow10 HTS Diptube Kit (includes item 3)2" Uniseal®Tank Full Probe AdapterO-ring, ½" OD x 3/8" ID½" Flexible TubingReed Switch Stem (barbed end)½" UnisealReed Switch FloatFloat Lock RingEmpty Float Indicator Kit – 10 HTSBarbed Adapter (Uniseal)

13141516171819202122

23

600340425385311037313900101313255247600343974600342932385310772600342467600346795317770012317770024600342798

Reed Switch Stem (threaded)Mid Level Float Indicator Kit – 10 HTSFull Float Indicator – 10 HTS1 ½" TankSaver™ Valve (incl. item 3)5/8" Barbed Elbow1 ½" UnisealSwivel Elbow/Uniseal Kit¼-20 x ¾" Hex Head ScrewFlat Washer, 5/8" OD x .281" ID x .050" Thick12VDC Low-Profile Vacuum Generator24VDC Low-Profile Vacuum GeneratorMounting Spindle

Item Part No. Description Item Part No. Description

PARTS LIST – 10HTS

10-GALLON HOLDING TANK SYSTEM

9

123456789101112

600342806385310707600343023313255247385310708600342932600343071306342871385310709600342789600347802385310710

1 ½" MPTx 90° ElbowDiptube Kit, 18HTS (includes item 3)2" Uniseal1 ½" TankSaver (includes item 3)1 ½" Short Elbow Kit (includes item 6)1 ½" Uniseal2" SS Hose Clamp1 ½" OdorSafe Hose1 ½" Sweep Elbow Kit1 ½" Close Nipple1 ½" Duckbill Valve1 ½" Swivel Nut Elbow Kit (includes item 13)

1314

15

1617181920-

600342781317759012317759024385310713385310711600343657600340424600340423600340425600342766385310714

1 ½" Slip Joint Seal12VDC Vacuum Generator24VDC Vacuum GeneratorTankWatch Cap w/ventTankWatch Cap w/vent, Deutsch ConnectorStem, Barbed-EndFloat Lock RingReed Switch FloatStem, Threaded-EndO-Ring, 3/8" x ½" x .060Optional 10' Wiring Harness withDeutsch Connectors (not shown)




10

123456

7891011121314

151617181920212223242526

PARTS LIST – 28HTS and 40HTS

309310001385310673600342958385310635600342932317301200317401200317302400317402400600342467600346795600342173600342806

385310647 385310648600343023

385310719 385310720385310645 385310646385310715 N/A

600343071306342871385310135600345932306345688600342766600340423600340425600340424231355247600342798600343657

Holding Tank Vent Filter (does not include item 17)Filter Mounting Hardware½" Uniseal®Inlet Elbow (includes item 5)1 ½" Uniseal12VDC Discharge Pump12VDC Discharge Pump with Deutsch Connectors24VDC Discharge Pump24VDC Discharge Pump with Deutsch Connectors¼-20 x ¾" Hex Head Screw¼" Flat Washer1 ½" PVC Male Plug (used only without optional discharge pump)1 ½" MPT Elbow x 90Diptube Assembly2" UnisealHolding Tank, MachinedTankWatch CapTankWatch Cap w/optional Deutsch connectors2" Hose Clamp1 ½" OdorSafeâ HoseVent Filter Fittings7/8" Hose Clamp5/8" Vent HoseO-RingFloatStem, Threaded-EndLock RingTankSaver Valve (includes item 12)Mounting SpindleStem, Barbed-End

Item Part Number Description

28-GALLON and 40-GALLONHOLDING TANK SYSTEMS

28HTS 40HTS

11

Item DescriptionPartNumber

1234567891011

12131415

Vent Filter Fittings1½" Uniseal®½" Uniseal1½" Holding Tank Vent Filter5/8" Holding Tank Vent FilterThumblock Clamp#6 x ½" Oval Head SS ScrewStrapFlat Washer, .625 x .281 x .050 SS¼-20 x 3/4" Long Hex Head SS Screw12VDC Discharge Pump24VDC Discharge Pump2" SS Clamp1½" OdorSafe® Hose1½" MPT ElbowDiptube Kit – 35 HTS (includes item 16)

385310135600342932600342958385310004385310001600343528600343536600343529600346795600342467317301200317302400600343071306342871600342806385310837

16171819

20

212223242526272829

600343023600341370600347167317770012317770024385310842385310843385310787385310844313255247385310841385310840385310839600340423600340424385310914

2" Uniseal¼-20 X 1¼" long Hex Head SS ScrewFlat Washer, .850 x .294 x .050 SS12VDC Low-Profile Vacuum Generator24VDC Low-Profile Vacuum GeneratorRelay/Bracket Kit – 12VDCRelay/Bracket Kit – 24VDC45° Elbow Kit (includes item 2)Tank Inlet Elbow Kit (includes item 2)1½" TankSaver Valve (includes item 16)Full Level IndicatorMid Level IndicatorEmpty Level IndicatorFloatLock Ring1½" Swivel Elbow Kit

Item DescriptionPartNumber



12

Item


123456

78910111213141516171819202122232425

1-1/2" MPT Elbow x 9042 HTS Diptube (includes item 3)2" UnisealTankSaver Valve (includes item 3)1-1/2" Uniseal12VDC Vacuum Generator (includes item 24)12VDC Vacuum Generator with Deutsch Connectors (includes item 24)24VDC Vacuum Generator (includes item 24)24VDC Vacuum Generator with Deutsch Connectors (includes item 24)Kit, Level Indicators – 42HTS, with Deutsch connectorsStem, Threaded-EndLock RingFloatO-Ring2" Hose Clamp1-1/2" OdorSafe Hose1-1/2" PVC Male Plug (used only without optional T Pump)Vent Filter FittingsVent Filter (does not include item 15)1/2" UnisealFilter Mounting HardwareMounting SpindleStem, Barbed-EndTank Full Float42 HTS Mid Level Float42 HTS Empty Level Float42 HTS Vacuum Generator Outlet (includes item 5)12VDC Discharge Pump12VDC Discharge Pump with Deutsch Connectors24VDC Discharge Pump24VDC Discharge Pump with Deutsch Connectors


600342806385310668600343023313255247600342932385310669385310717385310672385310718385310905600340425600340424600340423600342766600343071306342871600342173385310135385310001600342958385310673600342798600343657313900101385310909385310915385311035317301200317401200317302400317402400

Part No. Description

13

NOTE: When reassembling pump, tighten screw (item no. 7) , to 20 ±2 lbs., or until snug.Overtightening will cause holes to strip.

PARTS LIST – VACUUM GENERATOR

123456789

101112131415161718

600340237600343027600342804600341506600344087600342332600341503385310151600340664600343006600347807600342783600342779385310539600342782600342778385310540600347802

Pan Phillips Head Screw, #4 x 3/8", SSFlat Washer, .312" OD x .030 Thick, SSMotor/Switch CoverPump Top ClosureFlat Washer, #10 x 5/8" OD, SSHex Washer Head Screw, #10-32 x ½", SSHex Washer Head Screw, #10-32 x 7/8", SSO-Ring KitBushingShoulder Screw, ½ x .687 x 3/8-16Bellows Clamp3-3/4" Diameter Worm Gear ClampO-Ring, 3" ID x 3 ¼" ODDiptube Assembly Kit (includes item 13)2 ½" Diameter Worm Gear ClampO-Ring, 2" ID x 2-1/4" ODVacuum Switch Kit (includes items 15, 16)Duckbill Valve

19202122232425262728293031

31A32NSNS

600342789600342467600346795385310635600342932385310542600347800600347801600341504385230980600344470600347788385310245385310246600342798385310774385310775

1 ½" NPT Close Nipple¼-20 x ¾" Hex Head Screw, SSFlat Washer, .625" OD x .281" ID x .050Inlet Elbow Kit (includes item 23)1 ½" Uniseal®Vacuum Generator TankValve NippleValve AdapterPump BodyBellows Assembly (includes item 9)Pump Eccentric¼-28 x 5/16" Set Screw, ½ Dog Point12 VDC Motor Kit24 VDC Motor KitMounting SpindleKit, VG Pump Assembly, 12VDCKit, VG Pump Assembly, 24VDC


STANDARD VACUUM GENERATOR

14

PARTS LIST – LOW-PROFILE VACUUM GENERATOR

LOW-PROFILEVACUUM GENERATOR

Pan Phillips Head Screw, #4 x 3/8", SSPump CoverTop ClosureHex Washer Head Screw, #10-12 x 7/8", SSHex Washer Head Screw, #10-32 x ½", SSO-Ring Replacement KitBushingShoulder Screw, ½" x .687 x 3/8-16Bellows ClampValve NippleDuckbill ValveValve AdapterPump BodyPump FittingO-RingDiptube Kit – Low-Profile VGUniseal® 1½"Pan Phillips Head Screw, #4 x 1/4"

Part No.123456789101112131415161718

Item Description600340237385640239600341506600341503600342332385310151600340664600343006600347807600347800600347802600347801600341504600344676600343936600344675600342932600343621

Part No.Item Description192021222324

25262728

2929A

600343027600343913385310626600342798385310755385310635385310690385310787385230980600344470600347788385310756385310245385310757385310246600343053600343053

Washer, #6 x 3/8"Vacuum Switch CoverVacuum Switch KitMounting SpindlesLow-Profile Vacuum TankInlet Elbow AssemblyStraight Inlet (Optional)45° Inlet (Optional)Bellows AssemblyPump EccentricSet Screw, 1/4-28 x 5/16", ½ Dog Point12 VDC Motor w/ Deutsch Connection12 VDC Motor24 VDC Motor w/ Deutsch Connection24 VDC MotorRelay, SPDT 12 VDC 40/30 Amp, VF4Relay, SPDT 12 VDC 40/30 Amp, VF4

15

SANIPUMP™ OVERBOARDDISCHARGE PUMP

PARTS LIST – DISCHARGE PUMP

Item Part No. Description

*Note: When reassembling pump, tighten screws to 20±2lbs., or until snug.Over-tightening will cause holes to strip.

123456789101112131415

15A1617

600340237385640239600341502600342332385310151600340664600343006600347807600340669600347802600341489385230980600347788600344470385310245385310246600341503600341113

385310250

#4 x 3/8" Pan Head ScrewPump Cover KitPump Top Closure#10-32 x ½" Hex Head ScrewO-Ring Replacement KitBushingShoulder Screw, ½" x .687 x 3/8-16Bellows ClampValve Nipple1 ½" Duckbill ValvePump BodyBellows Assembly (includes item 6)Set Screw, ¼-28 x 5/16"Eccentric12 VDC Motor24 VDC Motor#10-12 x 7/8" Hex Washer Head Screw *1" x 1 ½" Reducing AdapterNot ShownPump Assembly, Less Motor(includes items 3, 5, 6, 8, 9, 10, 11, 12, 19)

16

HTS COMPONENTSTankSaver™ VacuumRelief ValveSeaLand’s TankSaver™vacuum relief valve preventsdamage due to holding tankimplosion from docksidepumps that operate at veryhigh levels of vacuum. TheTankSaver valve opens auto-matically under vacuum, butremains sealed regardless of shock-loading orvibrations.

TankWatch® 4 Level Monitor and Micro-FloatSwitchesIncludes four tank level indicator lights – Empty, Low,Mid and Full, and international symbology of four tanklevels. One light is always on. Reliable micro-floatswitches are installed in holding tank. No electricalcomponents come in contact with waste or water. Op-erates on 12 or 24-volt DC. Uses only .017 amps at13-volts. Micro-float switches are installed in all HTStanks either as a unit (with a TankWatch cap) or asindividual Empty, Mid and Full probes.

SaniPump™ Overboard Waste Discharge Pump*This T-series discharge pump can run dry without harmand draws just 6 amps at 12 VDC. Delivers flow rateof just over 3.9 gallons per minute (14.7 liters perminute). Emptying the tank of the 10HTS takes aboutthree minutes, and for the 42 HTS about 11 minutes.The discharge pump is connected to a through-hullfitting. Check Marine Sanitation Regulations for infor-mation on areas where discharge is allowed.

SaniGard™ Holding Tank Vent Filter*The vent filter stops odors that escape from the hold-ing tank vent. It contains odor-removing filter mediato keep your boat smelling clean and pleasant. Eachcartridge is good for an entire season and is easilyreplaced for a fresh start. The vent filter includesmounting brackets and hose adapters, and is avail-able with either 5/8-inch (16mm) or 1½-inch (38mm)hose fittings.

* Not available on all HTS models.

VacuFlush Shutdown RelayTo prevent overfilling of a holding tank, a shutdown re-lay is supplied as standard with 10HTS, 18HTS, and35HTS models. The relay is optional (p/n 600341292 -12VDC, p/n 600342490 - 24VDC) on standard 28HTS,40HTS, and 42HTS models. The relay shuts off powerto the vacuum generator when the holding tank reachesthe "Full" level, preventing further flushing of the toilet.

17

VACUFLUSH® VACUUM GENERATORS

Low-ProfileVacuumGenerator

Vacuum GeneratorsVacuFlush vacuum generators combine the vacuumtank and vacuum pump in one unit. Our standard andlow-profile configurations eliminate hose runs betweenthe vacuum tank and pump that are found in previousVacuFlush sanitation system installations. Standard

Vacuum Generator

OTHER HTS FEATURESOdorSafe® Sanitation HoseOur exclusive OdorSafe hose provides the best odorbarrier of any marine hose available. A result of morethan a decade of research and development, this sani-tation hose delivers up to 16 times greater resistanceto sulfurous malodors than other so-called “no-odor”marine hoses. On HTS models, this hose is used forall 1 1/2-inch (38mm) hose connections. It's also thebest choice for connecting the discharge pump to thethrough-hull and deck waste fittings.

Diptube Discharge KitOur diptube discharge design allows for removal ofwaste from the top of the holding tank rather than nearthe bottom of the tank. This feature greatly reducesthe opportunities for stagnant sewage to sit in tankdischarge lines – a main cause of odor permeationand hose failure.

18

HOLDING TANK DISCHARGE INFORMATIONOVERBOARD DISCHARGEWhen is it okay to discharge overboard?The answer to this question depends on where you are boating. If you are three miles or more offshore in U.S.coastal waters, you can legally discharge untreated effluent from the holding tank.Within three miles of shore, however, it is not legal to dump raw sewage into the water. Effluent can only bedischarged if it has been treated by a Type I or II marine sanitation device (MSD), and if the waters have notbeen designated as a “No Discharge Zone.”Otherwise, boats within a coastal “No Discharge Zone” must contain their waste in a Type III MSD which usesa holding tank. SeaLand Holding Tank Systems are Type III MSDs. The waste can be discharged at docksidepump-out facilities. All rivers and freshwater lakes, including the Great Lakes, are protected by the Environmen-tal Protection Agency as “No Discharge Zones” as well, so Type III MSDs must be used in these areas, andsewage can be discharged only at dockside pump-out facilities.

No Discharge ZonesAn up-to-date list of No Discharge Zones can be located on the World Wide Web at:http://www.epa.gov/owow/oceans/regulatory/vessel_sewage/vsdnozone.html.

DOCKSIDE DISCHARGEWhen pumping out a holding tank, it is important to create an airtight seal between the deck’s discharge fittingand the dockside suction pump discharge hose. But because deck fittings vary in thread size and internaldimensions, it is sometimes difficult to achieve this seal.Dockside pump suppliers have tried to solve this problem by using a tapered rubber nozzle that will fit moststandard size openings. But the fit is not airtight, so not enough vacuum may be achieved for complete pump-out. And the rubber abrades over time, reducing its effectiveness.Another remedy is a cam-operated coupling. A special adapter is required for this, and marina-suppliedadapters have a strange way of disappearing.The SeaLand NozAll™ Pump-out Adapter workswith both tapered rubber nozzle and cam-operated fit-tings. There are three NozAll models available tomatch the most popular deck fitting threads and sizes.NozAllPart No. Deck Fitting Thread, Size Description310343502 11.5 tpi (4.5 tpcm), 1-7/8 in. OD (48mm)310343503 11.5 tpi (4.5 tpcm), 1-5/8 in. OD (41mm)310343504 16 tpi (6.3 tpcm), 1-5/8 in. OD (41mm)

Helpful Pump-out HintsCompletely unroll the suction hose and lay it with the straightest possible runs to help increase flow.Inexpensive plastic or latex gloves should be used. Do not dispose of gloves in water.Always wash hands with hot water and soap when finished.Clean and disinfect surfaces with typical bathroom cleaner.Store hose and attachments after every use. Leave area in clean condition for next boat owner.Continually flush pump-out connection with fresh water during pump-out if you cannot make an airtightconnection.

1 2

3

4

1. Tapered rubbernozzle

2. Cam-operatedfitting

3. NozAll pump-outadapter

4. Deckfitting

19

CUSTOMER SERVICEThere is a strong, worldwide network to assist in servicing andmaintaining your sanitation system. For the Authorized ServiceCenter near you, please call from 8:00 a.m. to 5:00 p.m. (ET)Monday through Friday. You may also write us at DometicCorp., P.O. Box 38, Big Prairie Ohio 44611.Telephone: 1 800-321-9886 U.S.A. and Canada

330-496-3211 International

You may also contact or have your local dealer contact theParts Distributor nearest you for quick response to yourreplacement parts needs. They carry a complete inventoryfor the SeaLand product line.

Fax: 330-496-3097 U.S.A. and Canada330-496-3220 International

U.S.A. - Southwest(AZ, CO, NV, UT, CA-south)Ardemco Marine Specialties778 West 17th StreetCosta Mesa, CA 92627Tel: 949-722-7672

800-253-0115Fax: 949-642-9582E-mail: [email protected]: Rick GlasserU.S.A. – Upper Midwest(IA, MN, NE, ND, SD, WI)PowerHouse Marine518 LoganLa Crosse, WI 54603Tel: 608-784-9580

888-752-4539Fax: 608-784-8422E-mail:[email protected]: Dave TuckerU.S.A. – Northern CaliforniaFox Marine2250 Zanker Road, Unit DSan Jose, CA 95131Tel: 408-451-9055

800-826-2873E-mail: [email protected]: Charlie Barker

INTERNATIONALDISTRIBUTORSArgentinaTrimer S.A.Del Arca 55, B1646 AASan FernandoPCIA, De Buenos AiresTel: 5411 4580 0444Fax: 5411 4580 0440E-mail: [email protected]: Carlos Friedlanderor Pablo VillarAustraliaDometic Pty Ltd6 Treforest DriveClayton, Victoria 3168PO Box 1140Clayton South, Victoria 3169Tel: (03) 9545 5655Fax: (03) 9545 5966Email:[email protected]: Petra BachAustriaOcean MarineSee GermanyBelgiumAuerhaan B.V.See The NetherlandsCanada - EastEastern Marine Systems, Inc.12-A Leslie StreetToronto, Ontario M4M 3H7Tel: 416-465-1668

888-764-1111Fax: 416-465-2098E-mail: [email protected]: Paul Gales

Canada - WestWestern Marine Company1494 Powell StreetVancouver, BC V5L 5B5Tel: 604-253-7721

800-663-0600Fax: 604-253-2656

800-663-6790E-mail: sales@

westernmarine.comContact: Bill FalkCaribbeanBudget MarineP.O. Box 43425B Waterfront RoadCole Bay, PhilipsburgSt. MaartenNetherlands AntillesTel: 599 5 43134Fax: 599 5 44409Contact: Jackie LeechDenmarkDometic Origo ABSee SwedenFinlandNautikulma OyLantinen Pitkakatu 3320100 TurkuTel: 358 2 250 3444Fax: 358 2 251 8470E-mail: [email protected]: Teppo SiltalaFranceKent Marine Equipment3 rue de la Dutee - BP 20744815 Saint-HerblainTel: 33 2 40 92 15 84Fax: 33 2 40 92 13 16Contact: Luc TavoliniGermanyOcean MarineWendenstrasse 42920537 HamburgTel: 49 (0) 40 219 1042Fax: 49 (0) 40 219 1114E-mail: [email protected]: Thorsten LentzGreeceAmaltheia13 Papaflessa Str.143 43 N. HalkidonaAthens-GreeceTel: 30 (210) 25 88 985Fax: 30 (210) 25 88 986E-mail: [email protected]: Dimitris KyriazesHong KongFuncle Ltd.G/F, 81D, Pak Shek TerraceClearwater Bay RoadSai KungTel: 852 2335 0482Fax: 852 2335 0580Contact: Alan Reid

ItalySVAMA Nautica S.r.L.Via Del Lavaro 25/A248015 Montaletto Di Cervia(Ravenna)Tel: 390 544 965689Fax: 390 544 965734E-mail: svama-nautica@

svama-nautica.comContact: Claudio CasadioJapanTominaga & Co., Ltd.2-6-8 NishitenmaKita-ku, Osaka 530Tel: 81 (06) 365 5010Fax: 81 (06) 365 6294E-mail: [email protected]: A. TatsumiLuxembourgAuerhaan B.V.See The NetherlandsThe NetherlandsAuerhaan B.V.P.O. Box 22, 8200 AA LelystadPlatinastraat 158211 AR, LelystadTel: 31 (0) 320-286171Fax: 31 (0) 320-286170E-mail: accessoires@

auerhaan.nlContact: Bert van LoenenNetherlands AntillesBudget MarineP.O. Box 43425B Waterfront RoadCole Bay, PhilipsburgSt. MaartenTel: 599 5 43134Fax: 599 5 44409Contact: Jackie LeechNew ZealandLusty & Blundell Ltd.38 Tawa DriveAlbany, AucklandTel: 64 (09) 415 8303Fax: 64 (09) 415 8304Contact: Mike HarrisNorwayDometic Origo ABSee SwedenPhilippinesSolid Sales Philippines31 Horseshoe DriveBanawa Hills, Cebu City 6000Tel: 63 32 255 3002Fax: 63 32 255 3001E-mail: ssphils@

cebu.pw.net.phContact: Andy Y. Lim

Sardenia and SicilySVAMA NauticaSee ItalySingaporeMarina Yacht Services Pte.Ltd.No. 10 Tuas West Drive#01-01 to 04 Raffles MarinaSingapore 638404Tel: 65 862 4320Fax: 65 862 4431Contact: Johnny LimSpain, Balearic & CanaryIslandsDahlberg Sociedad AnonimaNicolau de Pacs, 3207006 Palma de MallorcaTel: 34 971 774751Fax: 34 971 771458E-mail: sealand@

dahlberg-sa.comContact: Rosa DahlbergSwedenDometic Origo ABSöndrumsvägen 35SE-302 39 Halmstad, SwedenTel: 46 (0) 35 17 57 00Fax: 46 (0) 35 17 57 10E-mail: [email protected]: Johan EdlundSwitzerlandOcean MarineSee GermanyTaiwanMercury Marine SupplyNo 488Ming Chuan 2nd RoadChyan Jenn District806 KaohsiungTel: 886 (07) 331 7293Fax: 886 (07) 332 4232E-mail: mms46654@

ms16.hinet.netContact: Mercury LiuTurkeyMarina Deniz AraclariFener Kalamis CAD. No:75Fenerbahce 81030IstanbulTel: 90 (0) 216 338 14 41Fax: 90 (0) 216 337 44 92E-mail: [email protected]: Isik AylanUnited KingdomLee SanitationFenny ComptonWharf Road, WarwickshireCV47 2FETel: 44 (0) 1295 770000Fax: 44 (0) 1295 770022E-mail: [email protected]: Chris Coburn

U.S.A.MASTER SANITATIONDISTRIBUTORSU.S.A. – North Central(IL, IN, KY, MI, OH)Midwest Marine Supply24300 Jefferson Ave.St. Clair Shores, MI 48080Tel: 586-778-8950

800-860-1540Fax: 586-778-6108E-mail: midwestmarine@

yahoo.comContact: Bob KennedyU.S.A. - Northeast(CT, DE, DC, MA, MD, ME, NH,NJ, NY, PA, RI, VA, VT, WV)Northeast Marine Sanitation69 Florida StreetFarmingdale, NY 11735Tel: 631-752-7606

800-352-4323Fax: 631-752-7615

888-283-7606E-mail: [email protected]: Mike StaritoU.S.A. - Northwest(AK, ID, MT, OR, WA, WY)Marine Sanitation, Inc.1900 N. Northlake Way, Suite 121Seattle, WA 98103Tel: 206-633-1110

800-624-9111Fax: 206-633-0317E-mail: marinesan@

mindspring.comContact: Ric KolbU.S.A. - South Central(AR, KS, LA, MO, MS, NM, OK,TX)AER SupplyP.O. Box 3492301 Nasa Road #1Seabrook, TX 77586Tel: 281-474-3276

800-767-7606Fax: 281-474-2714E-mail: [email protected]: Richard MillerU.S.A. - Southeast(AL, FL, GA, NC, PR, SC, TN, VI)Environmental Marine111 S.W. 23rd Street, Suite AFort Lauderdale, FL 33315Tel: 954-522-2626

800-522-2656Fax: 954-522-5152E-mail:[email protected]: John or Jill Hopkins

20

Dometic warrants, to the original purchaser only, that this product, if used for personal, family or household purposes, isfree from defects in material and workmanship for a period of one (1) year from the date of purchase.

If this Dometic product is placed in commercial or business use, it will be warranted, to the original purchaser only, to befree of defects in material and workmanship for a period of ninety (90) days from the date of purchase.

Dometic reserves the right to replace or repair any part of this product that proves, upon inspection by Dometic, to bedefective in material or workmanship. All labor and transportation costs or charges incidental to warranty service are tobe borne by the purchaser-user.

EXCLUSIONSIN NO EVENT SHALL DOMETIC BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES, FOR DAMAGESRESULTING FROM IMPROPER INSTALLATION, OR FOR DAMAGES CAUSED BY NEGLECT, ABUSE, ALTER-ATION OR USE OF UNAUTHORIZED COMPONENTS. ALL IMPLIED WARRANTIES, INCLUDING ANY IMPLIED WAR-RANTY OF MERCHANTABILITY OR FITNESS FOR ANY PARTICULAR PURPOSE, ARE LIMITED TO A PERIOD OFONE YEAR FROM THE DATE OF PURCHASE.

IMPLIED WARRANTIESNo person is authorized to change, add to, or create any warranty or obligation other than that set forth herein.

Implied warranties, including those of merchantability and fitness for a particular purpose, are limited to one (1) year fromthe date of purchase for products used for personal, family or household purposes, and ninety (90) days from the date ofpurchase for products placed in commercial or business use.

OTHER RIGHTSSome states do not allow limitations on the duration of an implied warranty and some states do not allow exclusions orlimitations regarding incidental or consequential damages; so, the above limitations may not apply to you. This warrantygives you specific legal rights, and you may have other rights which vary from state to state.

To obtain warranty service, first contact your local dealer from whom you purchased this product.

MANUFACTURER'S ONE-YEAR LIMITED WARRANTY

600343562 8/03

Dometic Corporation • Sanitation Systems13128 State Rt. 226, P.O. Box 38Big Prairie, OH 44611-0038 USA

330-496-32111-800-321-9886 • Fax: 330-496-3097

Email: [email protected]

® Registered; ™ Trademark of Dometic Corporation© Dometic Corporation

VacuFlush-HTS-models.pdf - Stroboflash

Documents

Transcript of VacuFlush-HTS-models.pdf - Stroboflash