2-7665

Page 1 of 8F-4225 9-25-08

716524086

5. Remove the tool box from the tractor and retain thehardware for later use.

6. Grind off existing SMV bracket from left hand ROPS,flush with the ROPS tube (Figure 3).

TRACTOR PREPARATION (Figures 1, 2, & 3)

IMPORTANT: Shut off engine, engage parking brake,and remove key for swivel seat installation.

1. Disconnect the two electrical wires from the sensoron the bottom of the seat.

2. Remove the seat from the tractor by pulling the twocotter pins out of the seat pins where the seat mountingbrackets attach to the seat rail assembly (Figure 1).

3. Remove the mounting brackets from the tractor seat.Retain the four bolts and washers for later use (Figure1).

4. Loosen the bolt holding the seat belt latch in placeand rotate the latch to a horizontal position (Figure 2).Retighten the bolt.

SWIVEL SEAT INSTALLATION(Figures 4, 5, 6, & 8)

1. Attach the swivel mechanism (1) and latch (2) to theseat mounting brackets using 5/16”-18 x 3/4" capscrews (5), 5/16” washers (6), and 5/16”-18 lock nuts(7) (Figure 8).

NOTE: Make sure the latch pin fits into the hole inthe tab attached to the swivel assembly.

2. Install swivel assembly onto tractor by sliding the seatmounting plates onto the pins of the seat rail assembly(Figure 4).

MountingBrackets

Seat Pins

Seat RailAssembly

Figure 1

Figure 2Swivel

Assembly

Seat RailAssembly

Figure 4

CAUTION: DO NOT USE acutting torch or welder toremove existing SMVbracket. Only use a grinderto remove welds.

Grind off here

Figure 3

NEW HOLLAND SWIVEL SEAT KIT

ASSEMBLY MANUAL

Keep With Operator’s Manual

TRACTOR MODEL BACKHOE MODELT1010, T1030, Boomer 1020,

Boomer 1025

T1110, Boomer 1030910GH

716524086

Page 2 of 8F-4225 9-25-08

2-7665SWIVEL SEAT INSTALLATION (CONTINUED)

3. Connect the two female spade connectors on the wireharness (4) to the seat sensor (Figure 5)

NOTE: Orientation of the wires does not matter.

4. Place the seat onto the swivel assembly and routethe wire harness (4) through the bushing in the swivelassembly (Figure 5).

5. Attach the seat to the swivel assembly using the seathardware retained earlier (Figure 5).

6. Connect the male spade connectors on the wireharness (4) to the wires originally connected to theseat sensor.

NOTE: Orientation of the wires does not matter.

7. Using the hardware retained when removing the toolbox, attach the seat support (3) to the tractor in placeof the tool box (Figure 6)

Bushing

4

Figure 5SMV/CANISTER BRACKET INSTALLATION(Figures 7 & 9)

1. Install manual cannister (4) to the cannister mountplate (2) using 1/4”-20 x 3/4” cap screws (6), 1/4”washers (8), and 1/4”-20 lock nuts (10) (Figure 9).

2. Install cannister mount plate (2) and SMV bracket (1)around the left hand ROPS tube using 5/16”-18 x 2 3/4” cap screws (5), 5/16” washers (7), and 5/16”-18lock nuts (9) (Figure 9).

3. Using the same hardware as in the previous step,attach the clamp plate (3) to the cannister mount platearound the ROPS tube (Figure 9).

NOTE: When SMV sign is inserted into SMV socket,sign should not cover any part of the warning light. Ifneeded, move the SMV/Canister bracket up on theROPS tube.

4. Figure 7 shows completed installation from the rear ofthe tractor.

Figure 7Final Canister Bracket Assembly

3

Figure 6

2-7665

Page 3 of 8F-4225 9-25-08

716524086

1

2

3

4

5

6

7

5

6

7

6

7

Seat MountingBracket

Latch Pin

Tab

Figure 8Swivel Seat Assembly

PARTS LIST - SWIVEL SEAT ASSEMBLY

Item Part No. Description Qty.1 54868 ASSEMBLY, Swivel Seat Mechanism 12 54865 ASSEMBLY, Latch, Swivel Seat 13 54895 SUPPORT, Seat 14 54867 HARNESS, Wire 15 41838-26 HHCS 5/16”-18 X .75 GR5 46 42502-7 WASHER, Flat 5/16” 47 41840-2 NUT, Lock, 5/16”-18 4

716524086

Page 4 of 8F-4225 9-25-08

2-7665

1

2

3

4

5

7

10

10

7

7

7

7

7

68

9

Figure 9SMV/Canister Bracket Assembly

PARTS LIST - SMV/CANISTER BRACKET ASSEMBLY

Item Part No. Description Qty.1 55361 BRACKET, SMV 12 55359 PLATE, Canister Mount 13 55362 PLATE, Clamp 14 49722 CANISTER, Operations Manual 15 41838-57 HHCS 5/16”-18 X 2.75 GR5 46 41838-20 HHCS 1/4”-18 X 0.75 GR5 27 42502-7 WASHER, Flat 5/16” 88 42502-6 WASHER, Flat 1/4” 29 41840-2 NUT, Lock, 5/16”-18 410 41840-11 NUT, Lock, 1/4”-20 2

2-7665

Page 5 of 8F-4225 9-25-08

716524086OPERATION OF THE SWIVEL SEAT(Figures 10, 11, 12, 13, & 14))

IMPORTANT: Parking brake must be applied before op-erating the swivel seat.

1. Pull out the latch pin and rotate it a ¼ turn so that theroll pin rests on the front of the bushing (Figure 10).

2. Remove the linch pin from the side of the swivelmechanism (Figure 11).

3. Grasp the seat with one hand on the front of the seatand one hand on the top of the back support. Lift upand towards the back of the tractor in one smoothmotion. The seat will lift up and pivot on the four-barlinkage towards the rear of the tractor (Figure 12)

Figure 10

Linch Pin

Figure 11

Grasp Here

Grasp Here

Figure 12

Figure 13

4. With the four bar linkage resting on the stops, rotatethe seat clockwise 180° degrees. The seat shouldnow be facing the rear of the tractor (Figure 13)

5. Install the linch pin back in its place to lock the seatfrom rotating. Figure 14 shows the seat in the finalposition.

6. To return the seat to its original position, follow steps1-5 in reverse order: Remove the linch pin, rotate theseat counterclockwise 180°, pivot the seat forward anddown, reinsert the linch pin, and rotate the latch pinback into position.

NOTE: When pivoting the seat forward and down,verify the wire harness has not been pinched betweenthe base plate and bottom swivel plate.

Figure 14

716524086

Page 6 of 8F-4225 9-25-08

2-7665

1

2

3

5

9

10

7

6

6

8

5

5

54

4

45

5

5

5

7

7

7

7

7

4

PARTS LIST - SWIVEL SEAT MECHANISMITEM PART NO. NH NO. DESCRIPTION QTY.1 54862 WDMT, Swivel Plate 12 54864 WDMT, Plate, Bottom Swivel 13 54855 PLATE, Base 14 54856 LINK, Pivot 45 54857 BUSHING, 7/32 86 41838-21 HHCS 3/8”-16 X .75 GR5 87 41840-3 LOCK, Nut 3/8”-16 88 42577-5 BUSHING, Machinery, 1” X 1-1/2” X 14GA 19 6040-3 RING, 7/8” EXT. Retaining 110 44756-2 PIN, Linch, 3/16” X 1-1/4” 1

Figure 10Swivel Seat Mechanism

2-7665

Page 7 of 8F-4225 9-25-08

716524086

1

2

3

4

5

67

PARTS LIST - SWIVEL SEAT LATCHITEM PART NO. NH NO. DESCRIPTION QTY.1 54866 WDMT, Bracket, Lock 12 54873 ASSEMBLY, Pin 13 54861 PIN, Lock 14 6016-4 PIN, Roll 15 6043-28 SPRING, Compression 16 42502-6 WASHER, Flat 1/4” 17 41903-15 PIN, Cotter, 3/32” X .75 1

Figure 11Swivel Seat Latch

716524086

Page 8 of 8F-4225 9-25-08

2-7665

AMERICAN STANDARD CAP SCREWS METRIC CAP SCREWS

GENERAL TORQUE SPECIFICATIONSUSE THE FOLLOWING TORQUES WHEN SPECIAL TORQUES ARE NOT GIVEN

SAE GradeTyp. HeadMarkings

Metric ClassTyp. HeadMarkings

5 8 8.8 10.9

Cap Screw TORQUE

Assembly Torque

TORQUE TORQUE TORQUESize FT·LBS N·m FT·LBS N·m FT·LBS N·m FT·LBS N·m

Inches MIN MAX MIN MAX MIN MAX MIN MAX6.25 7.25 8.5 10 8.25 9.5 11 13

8 9 11 12 10.5 12 14 1614 15 19 20 18.5 20 25 27

17.5 19 23 26 23 25 31 3426 28 35 38 35 37 47.5 5031 34 42 46 41 45 55.5 6141 45 55.5 61 55 60 74.5 8151 55 69 74.5 68 75 92 10265 72 88 97.5 86 96 116 13076 84 103 114 102 112 138 15295 105 129 142 127 140 172 190111 123 150 167 148 164 200 222126 139 171 188 168 185 228 251152 168 206 228 203 224 275 304238 262 322 355 318 350 431 474274 305 371 409 365 402 495 544350 386 474 523 466 515 631 698407 448 551 607 543 597 736 809537 592 728 802 716 790 970 1070670 740 908 1003 894 987 1211 1337

Swivel Nutor Hose

ConnectionF. F. F. T.

TubeConnection

F. F. F. T.ft.·lb.in.·lb.Thread

SizeSize

Assembly Torque

ft.·lb.in.·lb.Swivel Nut

or HoseSize F. F. F. T.

-4

234568

10121416202432

5/16 - 243/8 - 24

7/16 - 201/2 - 20

9/16 - 183/4 - 167/8 - 14

1 1/16 - 121 3/16 - 121 5/16 - 121 5/8 - 121 7/8 - 122 1/2 - 12

90 ± 5170 ± 10220 ± 15260 ± 15320 ± 20570 ± 251060 ±501300 ± 501750 ±75

1920 ± 1252700 ± 1503000 ± 1503900 ± 200

7.5 ± 0.514 ± 118 ± 122 ± 127 ± 248 ± 290 ± 5110 ± 5145 ± 6160 ± 6

225 ± 12250 ± 12325 ± 15

1 ± .251 ± .251 ± .251 ± .25

1.5 ± .251.5 ± .251.5 ± .251.5 ± .251.5 ± .251.5 ± .251.5 ± .251.5 ± .251.5 ± .25

7/16 - 20 140 ± 10 12 ± 1 2 2-5 1/2 - 20 180 ± 15 15 ± 1 2 2-6 9/16 - 18 250 ± 15 21 ± 1 1 1/2 1 1/4-8 3/4 - 16 550 ± 25 45 ± 5 1 1/2 1

-12 1 1/16 - 12 1000 ± 50 85 ± 5 1 1/4 1-16 1 5/16 - 12 1450 ± 50 120 ± 5 1 1-20 1 5/8 - 12 2000 ± 100 170 ± 10 1 1-24 1 7/8 - 12 2400 ± 150 200 ± 15 1 1-32 2 1/2 - 12 3200 ± 200 270 ± 20 1 1

MIN MAX MIN MAX MIN MAX MIN MAX6 8 8 11 9 11 12 15

16 20 21.5 27 23 27 31 36.529 35 39 47 42 52 57 7052 62 70 84 75 91 102 12385 103 115 139 120 146 163 198

130 158 176 214 176 216 238 293172 210 233 284 240 294 325 398247 301 335 408 343 426 465 577332 404 450 547 472 576 639 780423 517 573 700 599 732 812 992637 779 863 1055 898 1098 1217 1488872 1066 1181 1444 1224 1496 1658 2027

1/4 - 201/4 - 285/16 - 185/16 - 243/8 - 163/8 - 247/16 - 147/16 - 201/2 - 131/2 - 209/16 - 129/16 - 18

Cap ScrewSize

MillimetersM6 x 1.00M8 x 1.25M10 x 1.50M12 x 1.75M14 x 2.00M16 x 2.50M18 x 2.50M20 x 2.50M22 x 2.50M24 x 3.00M27 x 3.00M30 x 3.00

5/8 - 115/8 - 183/4 - 103/4 - 167/8 - 9

7/8 - 141 - 8

1 - 14

37° JIC Fittings

Standard American and Metric Cap Screws

SAE O-Ring Fittings

NOTE: These values apply to fasteners as receivedfrom supplier, dry or when lubricated with normalengine oil. They do not apply if special graphite ormolysulphide greases or other extreme lubricants areused.

Swivel NutTorque

SwivelNut Hex

Size(in.)

ThreadSize(in.)

DashSize

-3-4-5-6-8

-10-12-14-16-20-24-32

568

1012162022253238

50.8

--9/16 - 18

--11/16 - 1613/16 - 16

1 - 141-3/16 - 121-3/16 - 121-7/16 - 121-11/16 - 12

2 - 12--

--11/16

--13/1615/161-1/81-3/8

--1-5/81-7/82-1/4

--

--16--245069

102102142190217--

--N·m lb ·ftf

12--1837517575

105140160--

O-Ring Face Seal Tube/Hose Swivel Nut

MetricTubeO.D.(mm)

INSTALLATION INSTRUCTIONS