Manual DRB IIIr Para Cargar El

DRB III UPDATE PROGRAM

AM User Guide

May 2002

Ver. 1.00

Copyright 2002 DaimlerChrysler Corporation

Dealer Technical Operations 800 Chrysler Drive, Auburn Hills, MI 48326-2757

IMPORTANT INFORMATION The information in this document has been carefully checked and is believed to be accurate. However, DaimlerChrysler Corporation (DaimlerChrysler) assumes no responsibility for any technical inaccuracies or typographical errors that may be contained herein. In no event will DaimlerChrysler be held responsible for direct, indirect, special, incidental, consequential or any other loss or damage caused by errors, omissions, misprints, or misinterpretation of the information found in this publication, even if advised of the possibility of such damages. DaimlerChrysler expressly disclaims any and all liability to any person, in respect of anything done or omitted, and the consequences if anything done or omitted, by any such person in reliance on the contents of this publication.

ALL RIGHTS RESERVED No part of this publication may be reproduced, reformatted or transmitted in any form or by any means, electronic or mechanical, including photocopying, recording, or through any information storage and retrieval system, currently available or developed in the future, without prior written approval of DaimlerChrysler. This document is protected by copyright laws. Unauthorized reproduction or distribution of all or part of this document may result in severe civil and criminal penalties and will invoke prosecution to the full extent of the law. The DaimlerChrysler Diagnostic Readout Box III and DRB III are trademarks or registered trademarks of DaimlerChrysler Corporation. This document also includes tradenames and trademarks of companies other than DaimlerChrysler Corporation.

DRBIII & PCMCIA CARD UPDATE PROCESS USERS GUIDE 1.00

2002 DaimlerChrysler Corporation 1

TABLE OF CONTENTS

PHASE 1 DETERMINE MINIMUM PC REQUIREMENTS .......................................................... 1

DRBIII UPDATE PROGRAM SYSTEM REQUIREMENTS ............................................................................. 1 Hardware:...................................................................................................................................................... 1 Operating System:......................................................................................................................................... 1

PHASE 2 PERFORMING THE PC INSTALLATION:.................................................................... 2

PHASE 3 UPDATE DRBIII TOOLMODE SOFTWARE VERSION............................................ 4

PHASE 4 UPDATE A PCMCIA MEMORY CARD.......................................................................... 7

TECHNICAL SUPPORT........................................................................................................................... 9



PHASE 1 DETERMINE MINIMUM PC REQUIREMENTS DRBIII Update Program System Requirements

Before installing the DaimlerChrysler DRBIII Update program, make sure the computer meets the following minimum system requirements as well as the operating system.

Hardware: Intel 80486, 66 MHz or higher processor 16 MB of RAM (More memory improves performance) 50-MB available hard disk space VGA or higher-resolution monitor 16 x CD-ROM drive Mouse or pointing device Serial communications port (COM) Operating System: Windows 98 - or - Windows 95 Windows NT 4.0 Workstation Windows 2000 Professional



PHASE 2 PERFORMING THE PC INSTALLATION:

Typical Windows 98 Installation shown: 1. Exit all running software applications on the personal computer.

NOTE: As with any software application loading process, users should close any open programs that may interfere with loading. This may include items running in the background and may include some anti-virus programs.

2. Place the DRB III Remote Update and Flash Reprogramming CD-ROM in the computers CD-ROM drive. NOTE: If the PC has the auto-install feature turned ON, the Setup program will initiate and install the DRBUpdate process, if not continue.

3. Click the Start button and click Run option.

4. In the Run dialog box, type D:\setup.exe where D:\ is the CD-ROM drive letter of that personal computer (PC). Click the OK button.



The InstallShield Wizard starts and will guides the setup process.

5. Click the OK button to close the InstallShield Wizard.



PHASE 3 UPDATE DRBIII TOOLMODE SOFTWARE VERSION In this phase there will be references to cables and connections. Please review the appropriate sections from the DRB III Hardware, Operation & Accessories Reference Guide publication number 510325 (CH6050) for details. 1. Exit all running software applications on the personal computer.

2. Click the Start button, point to Programs, point to DRBIII Update and

click DRBIII Update.

The DRBIII Update program opens.



3. Select the serial communications port (COM).

4. Select the DRBIII toolmode software release version and the corresponding language, if available.

5. Make the connection from PC to DRBIII. Using the RS-232 Peripheral

Communication Cable, CH7068 (DB9 a 9-pin null modem cable), connect one end to the selected computer communication port. Connect the other end to the recessed RS-232 port on the DRBIII scan tool.

6. Remove any PCMCIA card from the DRBIII scan tool.

7. Power up the DRBIII. It is important that the power not drop during these types of operations. Use CH7055 power cable with a suitable power supply or a vehicle by connecting CH7000/CH7010 cable. We recommend either having the vehicle running or a battery charger on the vehicle set to 14 volts.

8. From the DRBIII scan tools Main Menu, select 5. Run Memory Card Program option.

9. Select 1. Attempt Serial Communications on the No Memory Card Present menu. The screen should now display,

NO MEMORY CARD DETECTED Attempting Serial Communication Link Press Page Back to Exit

SonyPencil

SonyText BoxES IMPORTANTE QUE EL drb TENGA ESTA FUNCION DE LO CONTRARIO NO SE PUEDE ACTUALIZAR CON ESTE SOFTWARE



10. On the computer, click the Update button to download the DRBIII toolmode

software. NOTE: This process can take from 20 to 45 minutes depending on the nature of the software update. CAUTION: It is important NOT to lose power to the DRB III during this time.

The purple progress bar indicates data transfer.

11. When the DRBIII Toolmode software download is complete, click the

button on the upper right corner of the window to close the software application.



PHASE 4 UPDATE A PCMCIA MEMORY CARD In this phase there will be references to cables and connections. Please review the appropriate sections from the DRB III Hardware, Operation & Accessories Reference Guide publication number 510325 (CH6050) for details. 1. Exit all running software applications on the personal computer.

2. Click the Start button, point to Programs, point to DRBIII Update and

click, DRBIII Update.

The DRBIII Update program opens.



3. Select the serial communications port (COM).

4. Using the lower pick box Make International Super Card 94 97 Select the language version and the type of PCMCIA card. NOTE: A 4-megabyte size PCMCIA card is the minimum/maximum requirement. The original Supercard P/N CH8000 when issued was a 2-Meg card. There are NO updates available for that card/configuration. SRAM cards are usually only used by engineering groups not in field service. The 4MB Flash Cards (not SRAM Card, so change default from pick list) to update are:

CH8361 SuperCard2 (Yellow w/ Black lettering) CH8425 Sebring Stratus 2-door Coupe (ST22)

5. Make the connection from PC to DRBIII. Using the RS-232 Peripheral Communication Cable, CH7068 (DB9 type null modem cable), connect one end to the selected computer communication port. Connect the other end to the recessed RS-232 port on the DRBIII scan tool.

6. Remove any PCMCIA cards attached to the DRBIII scan tool.

7. Power up the DRBIII. It is important that the power not drop during these types of operations. Use CH7055 power cable with a suitable power supply or a vehicle by connecting CH7000/CH7010 cable. We recommend either having the vehicle running or a battery charger on the vehicle set to 14 volts.

8. From the DRBIII scan tools Main Menu, select 5. Run Memory Card Program option.

9. Select 1. Attempt Serial Communications from the No Memory Card Present menu. The screen should now display,

NO MEMORY CARD DETECTED Attempting Serial Communication Link Press Page Back to Exit



10. Insert the 4-Meg size PCMCIA card to the DRBIII scan tool.

11. On the computer, click the Update button to download the appropriate PCMCIA card software.

Data transfer is indicated by purple progress bar.

12. When the software download to the PCMCIA card is complete, click the button on the upper right corner of the window to close the software application.

TECHNICAL SUPPORT For assistance or technical support with the DRBUpdate program, please contact:

Miller Special Tools 1 800 801 5420

Manual DRB IIIr Para Cargar El

Documents

Transcript of Manual DRB IIIr Para Cargar El