Distribusi Responden Bukan Penderita Penyakit Diabetes Mellitus
AutoCad2
description
Transcript of AutoCad2
:: PRAKTIKUM AUTO-CAD
MENGGAMBAR OBJEK
DASAR
Oleh :
• Membuat garis dengan sistem
koordinat
– Dengan koordinat cartesius
• Misal :
? Buat garis dari titik A (40,20) ke titik B (80,80) Command: line
Specify first point: 40.20
Specify next point or [Undo]: 80,80
? Buat sebuah bangun segi 4 dengan panjang 70 dan
lebar 50 yang berawal dari titik 30,30 Command:
• Membuat garis dengan sistem
koordinat
– Dengan koordinat polar
• Misal :
? Buat garis dari titik A (40,20) ke arah atas sejauh 40 Command: line
Specify first point: 40.20
Specify next point or [Undo]: @40<90
? Buat sebuah bangun segi 4 dengan panjang
70 dan lebar 50 yang berawal dari titik 30,30 Command:
• Membuat Segi Empat
– Dapat diawali dengan:
• Comand: Rectangle atau rectang
• MenuDrawRectangle
• Toolbar Draw
• Membuat Segi Empat
– Dengan mouse menentukan titik
sudut 1 dan 2
1
2
• Membuat Segi Empat
– Dengan command menentukan titik
sudut 1 dan 2
Command: rectang
Specify first corner point or [Chamfer/Elevation/Fillet/Thickness/Width]: 30,20
Specify other corner point or [Dimensions]: 160,80
30,20
160,80
• Membuat Segi Empat
? Buat segi empat dengan sudut 1 di
koordinat (50,50) dan sudut ke 2 di
(150,150)
Command: rectang
Specify first corner point or [Chamfer/Elevation/Fillet/Thickness/Width]: 50,50
Specify other corner point or [Dimensions]: 150,150
• Membuat Segi Empat
– Dengan command menentukan
dimensi panjang dan lebar (2004)
Contoh : Command: rectang
Specify first corner point or [Chamfer/Elevation/Fillet/Thickness/Width]:20,20
Specify other corner point or [Dimensions]: D
Specify length for rectangles <0.0000>: 30
Specify width for rectangles <0.0000>: 20
Specify other corner point or [Dimensions]: tentukan arah sudut ke 2 (ATAS,
BAWAH, KANAN. KIRI)
• Segi Empat Sudut Terpancung (Chamfer)
5
10
Command: rectang
Specify first corner point or [Chamfer/Elevation/Fillet/Thickness/Width]: C
Specify first chamfer distance for rectangles <3.0000>: 10
Specify second chamfer distance for rectangles <4.0000>: 5
Specify first corner point or [Chamfer/Elevation/Fillet/Thickness/Width]: 20,20
Specify other corner point or [Dimensions]: 50,50
• Segi Empat Sudut Tumpul (Fillet) 10
Command: rectang
Specify first corner point or [Chamfer/Elevation/Fillet/Thickness/Width]: F
Specify fillet radius for rectangles <0.000>: 10
Specify first corner point or [Chamfer/Elevation/Fillet/Thickness/Width]: 10,10
Specify other corner point or [Dimensions]: 80,80
• Segi Empat Bergaris Tebal (Width)
10
Command: rectang
Specify first corner point or [Chamfer/Elevation/Fillet/Thickness/Width]: w
Specify line width for rectangles <0.0000>: 10
Specify first corner point or [Chamfer/Elevation/Fillet/Thickness/Width]: 10,10
Specify other corner point or [Dimensions]: 80,80
Settingan harus
dikembalikan ke nilai awal
agar tidak membingungkan
kecuali akan dilkukan
kombinasi
• Segi Empat dengan kombinasi
Kombinasi fillet dengan
width
Kombinasi Charm
dengan width
• Membuat lingkaran
– Dapat diawali dengan:
• Comand: Circle atau C
• MenuDrawCircle[Pilih acuannya]
• Toolbar Draw
• Membuat lingkaran
– Dengan menggunakan
centre dan radius
Contoh:
? buat lingkaran yang ber-
centre di 40,50 dengan
radius 30
Command: C
CIRCLE Specify center point for circle or [3P/2P/Ttr (tan tan radius)]: 40,50
Specify radius of circle or [Diameter]: 30
• Membuat lingkaran
– Dengan menggunakan
centre dan diameter
Contoh:
? buat lingkaran yang ber-
pusat di 40,50 dengan
radius 60
Command: C
CIRCLE Specify center point for circle or [3P/2P/Ttr (tan tan radius)]: 40,50
Specify radius of circle or [Diameter] <30.0000>: D
Specify diameter of circle <60.0000>: 60
• Membuat lingkaran
– Dengan menggunakan
two point circle (2P)
Contoh:
? buat lingkaran yang
melalui titik 40,20 dan
titik 40,80
Command: C
CIRCLE Specify center point for circle or [3P/2P/Ttr (tan tan radius)]: 2P
Specify first end point of circle's diameter: 40,20
Specify second end point of circle's diameter: 40,80
• Membuat lingkaran
– Dengan menggunakan
three point circle (3P)
Contoh:
? buat lingkaran yang
melalui titik (40,20) ;
(10,50) dan titik (40,80)
Command: CIRCLE
CIRCLE Specify center point for circle or [3P/2P/Ttr (tan tan radius)]: 3P
Specify first point on circle: 40,20
Specify second point on circle: 10,50
Specify third point on circle: 40,80
• Membuat lingkaran
– Menggunakan tangent,tangent, radius
menggambarkan suatu lingkaran yang menyinggung ke
suatu obyek yang dipilih, dimana titik singgung tersebut
akan mendekati titik tangen yang dipilih
1
2
A
B
Contoh:
? Gambar lingkaran
dengan radius 30 yang
akan menyinggung
lingkaran 1 dan
lingkaran 2 di titik A
dan B
Command: C
CIRCLE Specify center point for circle or [3P/2P/Ttr (tan tan radius)]: ttr
Specify point on object for first tangent of circle: klik di A
Specify point on object for second tangent of circle: klik di B
Specify radius of circle <20.0000>: 30
1
2
A
B
• Setting lembar kerja sbb:
– Unit dalam centimeter ; Limit = (0,0) dan (1000,1000)
– Grid & Snap = 50; Tulis Nama di kanan atas
• Segi Empat
– Buat segi empat sudut tumpul dengan radius sudut tumpulnya
sebesar 150 dengan tebal garisnya 50 dan segi empat ini dibuat
dengan dari titik sudut ke 1 (100,100) dan titik sudut ke 2 di
(800,700)
• Lingkaran
– Buat lingkaran yang melalui titik (500,0); (100,400) dan (900,400)
• Simpan file Nim_Nama.dwg.
• Metode Edge
– Menentukan ukuran panjang salahsatu
garis sisi
Command: POLYGON
Enter number of sides <4>: 5
Specify center of polygon or [Edge]: E
Specify first endpoint of edge: KLIK Di 1
Specify second endpoint of edge: KLIK Di 2
1 2
• Metode Inscribed – Menentukan titik pusat dan jari-jari dari pusat
polygon ke salahsatu sudut polygon
Command: POLYGON
Enter number of sides <5>: 6
Specify center of polygon or [Edge]: KLIK Di 1
Enter an option [Inscribed in circle/Circumscribed about circle] <I>: I
Specify radius of circle: KLIK Di 2
1
2
• Metode Circumscribet – Menentukan titik pusat dan jari-jari dari pusat
polygon ke titik tengah salahsatu sisi palygon
1
2
Command: POLYGON
Enter number of sides <6>: 7
Specify center of polygon or [Edge]: KLIK Di 1
Enter an option [Inscribed in circle/Circumscribed about circle] <I>: C
Specify radius of circle: KLIK Di 2
• Menggambarkan bentuk cincin yang
diameter dalam dan luarnya berbeda Command: DONUT
Specify inside diameter of donut <5.0000>: 6
Specify outside diameter of donut <6.0000>: 8
Specify center of donut or <exit>: 5,5
8 6
5,5
• Koordinat 3 titik
Command: ARC
Specify start point of arc or [Center]: 2,2
Specify second point of arc or [Center/End]: 5,5
Specify end point of arc: 8,2
2,2
5,2
8,2
• Titik awal, titik pusat, titik akhir
Command: ARC
Specify start point of arc or [Center]: 2,2
Specify second point of arc or [Center/End]: C
Specify center point of arc: 2,4
Specify end point of arc or [Angle/chord Length]: 0,4
2,2
2,4 0,4
• Titik awal, titik pusat, ukuran sudut
Command: ARC
Specify start point of arc or [Center]: 4,2
Specify second point of arc or [Center/End]: C
Specify center point of arc: 5,5
Specify end point of arc or [Angle/chord Length]: A
Specify included angle: 225
4,2
5,5 225o
• Titik awal, titik pusat, panjang tali busur
Command: ARC
Specify start point of arc or [Center]: 4,2
Specify second point of arc or [Center/End]: C
Specify center point of arc: 5,5
Specify end point of arc or [Angle/chord Length]: L
Specify length of chord: 5
4,2
5,5
5
• Titik awal, titik akhir, ukuran sudut
Command: ARC
Specify start point of arc or [Center]: 5,5
Specify second point of arc or [Center/End]: E
Specify end point of arc: 10,2
Specify center point of arc or [Angle/Direction/Radius]: A
Specify included angle: 90
10,2
90o
5,5
• Titik awal, titik akhir, arah busur
Command: ARC
Specify start point of arc or [Center]: 4,3
Specify second point of arc or [Center/End]: E
Specify end point of arc: 1,8
Specify center point of arc or [Angle/Direction/Radius]: D
Specify tangent direction for the start point of arc: 45
4,3 45o
1,8
• Titik awal, titik akhir, ukuran jari-jari
Command: ARC
Specify start point of arc or [Center]: 4,3
Specify second point of arc or [Center/End]: E
Specify end point of arc: 1,8
Specify center point of arc or [Angle/Direction/Radius]: R
Specify radius of arc: 3
4,3
3
1,8
• Titik pusat, titik awal, titik akhir
Command: ARC
Specify start point of arc or [Center]: C
Specify center point of arc: 5,5
Specify start point of arc: 3,2
Specify end point of arc or [Angle/chord Length]: 2,7
3,2
2,7
5,5
• Titik pusat, titik awal, ukuran sudut
Command: ARC
Specify start point of arc or [Center]: C
Specify center point of arc: 5,5
Specify start point of arc: 5,2
Specify end point of arc or [Angle/chord Length]: A
Specify included angle: 135
5,2
135o 5,5
• Titik pusat, titik awal, panjang tali busur
Command: ARC
Specify start point of arc or [Center]: C
Specify center point of arc: 5,5
Specify start point of arc: 5,2
Specify end point of arc or [Angle/chord Length]: L
Specify length of chord: 5
5,2
5,5
• Melanjutkan dari busur/line yang
sebelumnya dibuat
Command: ARC
Specify start point of arc or [Center]: <tekan enter>
Specify end point of arc: KLIK Di A
A