Post on 11-May-2023
Nederlandse
NEN-EN 837-1 Manometers. Deel 1 : Manometers met Bourdon-buizen. Afmetingen, métrologie, eisen en beproeving
Pressure gauges. Part 1 : Bourdon tube pressure gauges. Dimensions, metrology, requirements and testing
1e druk, februari 1997 ICS 17.100
Dit document bevat de officiële Engelse versie van de Europese norm EN 837-1, december 1996.
Deze norm heeft de status van Nederlandse norm.
Normcommissie 341 030 "Manometers"
Behoudens uitzondering door de wet gesteld mag zonder schriftelijke toestemming van het Nederlands Normalisatie-instituut niets uit deze uitgave worden verveelvoudigd en/of openbaar gemaakt door middel van fotokopie, microfilm, opslag in computerbestanden of anderszins, hetgeen ook van toepassing is op gehele of gedeeltelijke bewerking.
Het Nederlands Normalisatie-instituut is met uitsluiting van ieder ander gerechtigd de door derden verschuldigde vergoedingen voor verveelvoudiging te innen en/of daartoe in en buiten rechte op te treden, voor zover deze bevoegdheid niet is overgedragen c.q. rechtens toekomt aan de Stichting Reprorecht.
Hoewel bij deze uitgave de uiterste zorg is nagestreefd, kunnen fouten en onvolledigheden niet geheel worden uitgesloten. Het Nederlands Normalisatie-instituut en/of de leden van de commissies aanvaarden derhalve geen enkele aansprakelijkheid, ook niet voor directe of indirecte schade, ontstaan door of verband houdende met toepassing van door het Nederlands Normalisatie-instituut gepubliceerde uitgaven.
Prijsklasse 72
Nederlands Normalisatie-instituut
© 1997 Nederlands Normalisatie-instituut Kalfjeslaan 2, Postbus 5059,2600 GB Delft, Telefoon (015) 2 690 390, Fax (015) 2 690 190
Voorbeeld
Preview
Dit document is een voorbeeld van NEN / This document is a preview by NEN
Dit
do
cum
ent
mag
sle
chts
op
een
sta
nd
-alo
ne
PC
wo
rden
gei
nst
alle
erd
. Geb
ruik
op
een
net
wer
k is
alle
en.
toes
taan
als
een
aan
vulle
nd
e lic
enti
eove
reen
kom
st v
oo
r n
etw
erkg
ebru
ik m
et N
EN
is a
fges
lote
n.
Th
is d
ocu
men
t m
ay o
nly
be
use
d o
n a
sta
nd
-alo
ne
PC
. Use
in a
net
wo
rk is
on
ly p
erm
itte
d w
hen
a su
pp
lem
enta
ry li
cen
se a
gre
emen
t fo
r u
s in
a n
etw
ork
wit
h N
EN
has
bee
n c
on
clu
ded
.
Nederlands voorwoord
Voor de in deze norm vermelde andere normen bestaan in Nederland de volgende equivalenten:
Vermelde norm:
EN 4 7 2 : 1 9 9 4 EN 5 6 2 : 1 9 9 4
EN 837-2
EN 837 -3 :1996
EN 60068-2 -6 :1995
EN 60068 -2 -27 :1993
EN 60529 :1991
ISO 228 -1 :1994 ISO 1302 :1992 EN 22768 -1 :1993
ISO 2859 -1 :1989 ISO 7 0 0 0 : 1 9 8 9 EN 2 9 5 3 9 : 1 9 9 2
ISO 1 0 1 0 2 : 1 9 9 0 ANSI/ASME B1.20.1
Nederlandse norm: Titel:
NEN-EN 4 7 2 : 1 9 9 4 NEN-EN 562 :1995
NEN-EN 837-2
NEN-EN 837-3 :1997
NEN 10068-2-6 :1995
Manometers. Termen en definities Apparatuur voor autogeenlassen. Manometers voor gebruik bij lassen, snijden en verwante processen Manometers. Deel 2 : Aanbevelingen voor keuze en inbouw van manometers (in voorbereiding) Manometers. Deel 3: Manometers met plaat- en kegelveer. Afmet ingen, métrologie, eisen en beproeving Klimatologische en mechanische beproevingsmethoden voor elektrotechnische produkten. Deel 2: Beproevingen. Sectie 6: Bestandheid tegen trillen
NEN 10068-2 -27 :1994 Klimatologische en mechanische beproevingsmethoden voor elektrotechnische produkten. Deel 2 : Beproevingen. Sectie 27 : Proef Ea met leidraad: Schokken
NEN 10529 :1992 Beschermingsgraden van omhulsels van elektrisch materieel (IP-codering)
NEN-ISO 2768 -1 :1990 Algemene toleranties. Deel 1 : Toleranties voor lineaire en hoekmaten zonder afzonderlijke tolerantieaanduidingen
NEN-ISO 9 5 3 9 : 1 9 9 2 Materialen voor apparatuur voor autogeenlassen, snijden en aanverwante processen
Voorbeeld
Preview
Dit document is een voorbeeld van NEN / This document is a preview by NEN
EUROPEAN STANDARD EN 837-1
NORME EUROPÉENNE
EUROPÄISCHE NORM December 1996
ICS 17.100
Descriptors: Metrology, measuring instruments, manometers, vacuum gauges, indicating instruments, designation, specifications, dimensions, fidelity, safety, metrology inspection, marking
English version
Pressure gauges - Part 1 : Bourdon tube pressure gauges - Dimensions, metrology, requirements
and testing
Manomètres - Partie 1: Manomètres à tubes de Druckmeßgeräte - Teil 1: Druckmeßgeräte mit Bourdon - Dimensions, métrologie, prescriptions Rohrfedern - Maße, Meßtechnik, Anforderungen et essais und Prüfung
This European Standard was approved by CEN on 1996-10-30. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CEN member.
The European Standards exist in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom.
CEN European Committee for Standardization
Comité Européen de Normalisation Europäisches Komitee für Normung
Central Secretariat: rue de St assart, 36 В-1050 Brussels
© 1996 Copyright reserved to CEN members Ref. No. EN 837-1:1996 E
Voorbeeld
Preview
Dit document is een voorbeeld van NEN / This document is a preview by NEN
P a g e 2 EN 8 3 7 - 1 : 1 9 9 6
Contents
Foreword 3
1 Scope 4
2 Normative references 4
3 Definitions 5
4 Nominal sizes 5
5 Pressure ranges 6
6 Accuracy classes 6
7 Dimensions 7
8 Pressure element assembly 15
9 Requirements 16
10 Testing 27
11 Packaging for transportation 34
12 Designation 35
Annex A (informative) Examples of scale numbering for accuracy classes from 0,6 to 4 36
Voorbeeld
Preview
Dit document is een voorbeeld van NEN / This document is a preview by NEN
Page 3 EN 837-1:1996
Foreword
This European Standard has been prepared by the Technical Committee CEN/TC 141 "Pressure gauges - Thermometers - Means of measuring and/or recording temperature during the distribution of refrigerated frozen and quick-frozen products", the secretariat of which is held by AFNOR.
This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by June 1997, and conflicting national standards shall be withdrawn at the latest by June 1997.
This European Standard is a part of the series of the following standards :
- EN 837-1 : Pressure gauges - Part 1 : Bourdon tube pressure gauges-Dimensions, metrology, requirements and testing ;
- EN 837-2 : Pressure gauges - Part 2 : Selection and installation recommendations for pressure gauges ;
- EN 837-3 : Pressure gauges - Part 3 : Diaphragm and capsule pressure gauges-Dimensions, metrology, requirements and testing.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and the United Kingdom.
Voorbeeld
Preview
Dit document is een voorbeeld van NEN / This document is a preview by NEN
P a g e 4 EN 8 3 7 - 1 : 1 9 9 6
1 Scope
This European Standard specifies requirements for Bourdon tube (designated by B, see clause 12) indicating pressure gauges, vacuum gauges and combined vacuum and pressure gauges (compound gauges), with circular, spiral or coiled forms, from 40 to 250 nominal size with ranges up to 1600 bar for the measurement of gauge pressure.
A reading of zero bar is atmospheric pressure. 1 bar = 105 Pa.
Gauges specified have circular dials with concentric scales for industrial and test use.
The standard includes methods of test for performance to be applied at type approval and production piece tests.
The standard applies to gauges suitable for industrial use with common industrial fluids. It applies also to liquid-filled gauges, gauges for high pressure gases and gauges for use with oxygen or acetylene. It does not apply to pressure gauges with electrical contacts.
Pressure gauges for welding, cutting and associated processes are not included in this standard, but are specified in EN 562.
2 Normative references
This European Standard incorporates by dated or undated reference, provisions from other publications. These normative references are cited at the appropriate places in the text and the publications are listed hereafter. For dated references, subsequent amendments to or revisions of any of these publications apply to this European Standard only when incorporated in it by amendment or revision. For undated references the latest edition of the publication referred to applies.
Pipe threads, general purpose (inch).
Pressure gauges - Vocabulary.
Gas welding equipment - Pressure gauges used for welding, cutting and allied processes.
Materials used for equipment used in gas welding, cutting and allied processes (ISO 9539:1988).
Degrees of protection provided by enclosures.
Electrical engineering - basic environmental testing procedures - Part 2 : Tests - Test Fc and guidance : Vibration (sinusoidal).
Electrical engineering - basic environmental testing procedures - Part 2 : Tests - Test Ea and guidance : Shock.
Pipe threads where pressure-tight joints are not made on the threads - Part 1: Designation, dimensions and tolerances.
ANSI/ASMEB1.20.1
EN 472
EN 562
EN 29539
EN 60529
EN 60068-2-6
EN 60068-2-27
ISO 228-1
1994
1994
1992
1991
1995
1993
1994
Voorbeeld
Preview
Dit document is een voorbeeld van NEN / This document is a preview by NEN
P a g e 5 EN 8 3 7 - 1 : 1 9 9 6
ISO 1302 1992 Technical drawings - Methods of indicating surface texture on drawings.
EN 22768-1 1993 General tolerances - Part 1 : Tolerances for linear and angular dimensions without individual tolerance indications.
ISO 2859-1 1989 Sampling procedures for inspection by attributes - Part 1 : Sampling plans indexed by acceptable quality level (AQL) for lot-by-lot inspection.
ISO 7000 1989 Motor vehicles - Graphic symbols - Principles, synopsis.
ISO 10102 1990 Assembly tools for screws and nuts - Double-headed open-ended engineers* wrenches.
3 Definitions
For the purpose of this European Standard, the definitions given in EN 472 apply.
4 Nominal sizes
Nominal sizes of gauges are as follows : 40, 50, 63, 80, 100, 150, 160 and 250.
See table 2 for dimensions.
Voorbeeld
Preview
Dit document is een voorbeeld van NEN / This document is a preview by NEN
Page 6 EN 837-1:1996
5 Pressure ranges
The bar is the preferred unit of pressure.
Pressure ranges in bar :
0 to 0,6 0 t o 1 0 to 1,6 0 to 2,5 0 t o 4
Oto 6 0 t o 1 0 Oto 16 Oto 25 Oto 40
Oto 60 0 to 100 0 to 160 0 to 250 0 to 400
Oto 600 Oto 1000 Oto 1600
Vacuum ranges in bar :
Vacuum gauges have anti-clockwise pointer travel with increasing vacuum.
- 0,6 to 0 -1 to 0
Combined pressure and vacuum ranges in bar :
-1 to + 0,6 -1 to + 3 -1 to + 9 -1 to + 24 -1 to+1,5 -1 to+ 5 -1 to + 15
The Sl-units Kilopascal (kPa) and Megapascal (MPa) should follow the bar series from 0 to 60 kPa up to 1000 kPa, then change to 0 MPa to 1,6 MPa up to a maximum of 160 MPa.
6 Accuracy classes
The accuracy class stating the limits of permissible error is expressed as a percentage of the span.
The following accuracy classes are defined : 0,1; 0,25; 0,6; 1; 1,6; 2,5 and 4 (see table 1).
For gauges with a pointer stop, the accuracy class will cover 10 % to 100 % of the range. For gauges with a free zero, the accuracy class will cover 0 % to 100 % of the range and zero shall be used as an accuracy check point.
Voorbeeld
Preview
Dit document is een voorbeeld van NEN / This document is a preview by NEN
Page 7 EN 837-1:1996
Table 1 : Nominal size compared to the accuracy class
Nominal
size
40 and 50
63
80
100
150 and 160
250
Accuracy class
0,1
X
0,25
X
X
0,6
X
X
X
1
X
X
X
X
X
1,6
X
X
X
X
X
X
2,5
X
X
X
X
4
X
X
X
7 Dimensions
7.1 General tolerances
General tolerances : EN 22768-1
7.2 Cases and flanges
The user will have to determine the dimensions for panel cut-out according to the manufacturer's data.
Outside diameter of case Outside diameter of flange Diameter of fixing hole circle Diameter of fixing holes
threaded pressure connection ri
Figure 1
Voorbeeld
Preview
Dit document is een voorbeeld van NEN / This document is a preview by NEN
NEN Uitgeverijt.a.v. afdeling MarketingAntwoordnummer 102142600 WB Delft
Wilt u deze norm in PDF-formaat? Deze bestelt u eenvoudig via www.nen.nl/normshop
Gratis e-mailnieuwsbrievenWilt u op de hoogte blijven van de laatste ontwikkelingen op het gebied van normen,
normalisatie en regelgeving? Neem dan een gratis abonnement op een van onze
e-mailnieuwsbrieven. www.nen.nl/nieuwsbrieven
Gegevens Bedrijf / Instelling
T.a.v. O M O V
Klantnummer NEN
Uw ordernummer BTW nummer
Postbus / Adres
Postcode Plaats
Telefoon Fax
Factuuradres (indien dit afwijkt van bovenstaand adres)
Postbus / Adres
Postcode Plaats
Datum Handtekening
NEN Uitgeverij
Postbus 50592600 GB Delft
Vlinderweg 62623 AX Delft
T (015) 2 690 390F (015) 2 690 271
www.nen.nl/normshop
Stel uw vraag aanKlantenservice via:
@NEN_webcare
RetournerenFax: (015) 2 690 271 E-mail: marketing@nen.nl Post: NEN Uitgeverij, t.a.v. afdeling Marketing Antwoordnummer 10214, 2600 WB Delft (geen postzegel nodig).
Voorwaarden• De prijzen zijn geldig
tot 31 december 2015, tenzij anders aangegeven.• Alle prijzen zijn excl. btw,
verzend- en handelingskosten en onder voorbehoud bij o.m. ISO- en IEC-normen.
• Bestelt u via de normshop een pdf, dan betaalt u geen handeling en verzendkosten.
• Meer informatie: telefoon (015) 2 690 391, dagelijks van 8.30 tot 17.00 uur.
• Wijzigingen en typefouten in teksten en prijsinformatie voorbehouden.
• U kunt onze algemene voorwaarden terugvinden op: www.nen.nl/leveringsvoorwaarden.
preview - 2015
Bestelformulier
Normalisatie: de wereld op één lijn.
Stuur naar:
Ja, ik bestel
€ 74.30__ ex. NEN-EN 837-1:1997 en Manometers - Deel 1: Manometers met
Bourdon-buizen - Afmetingen, metrologie, eisen en beproeving