2
Patentsuni-chains A/S develops and manufactures products under a dynamic intellectual property portfolio. Products may be protected by one or more patents, utility models, designs or trademarks. A regularly updated list of all publicly available rights is published on our homepagewww.unichains.com. At time of print products in this catalog are protected by one or more of the following rights:
©2007, uni-chains A/S. Copying or reproduction of this catalog is prohibited without written permission.uni-chains® reserves the right to make changes without notice.The drawings are according to American projection. The drawings belong to uni-chains® and are not to be used orcopied without the permission in writing from uni-chains®.
US D509,038 SUS D503,841 SUS D502,585 SUS 6,857,517 B2US 6,758,329US 6,662,938DE/EP 0931736DK/EP 0931736IT/EP 0931736NL/EP 0931736US 6,073,756US 6,216,854DK 174527GB 2352220IT 1320239US 6,390,288US 6,412,625US 5,482,156US 5,305,869
US 5,027,944US 5,127,515US 5,307,923US 5,379,883US 5,697,492DE 69109610FR/EP 0480863GB/EP 0480863IT/EP 0480863DE 4312864GB 2309062DE 69506772FR/EP 0680898GB/EP 0680898IT/EP 0680898NL/EP 0680898SE/EP 0680898MR 1995 00926
The quality assurance system of uni-chains A/S is certified according to ISO 9001.
Trade Marksuni-chains A/S is in possession of the following registered trade marks:uni-chains®
Single Link®
Snap Link®
Quality Assurance System
3
www.unichains.com
uni-chains® Belt Catalog
Innovative belt solutions for all applications and industries from uni-chains®.
4
7
10
11
11
12
13
uni Belt Material Selection
uni Pin Material Selection
uni Reinforcement Material Selection
uni Rubber Material Selection
Approvals
Standard Belts
14
Pitch = 12.7 mm (0.50 in.)Straight running
Strength Index (POM)
Pitch = 12.7 mm (0.50 in.)Straight running
18
uni M-PNB M1 Snap Link®
uni M-QNB
Pitch = 12.7 mm (0.50 in.)Straight running
22
Pitch = 19.05 mm (0.75 in.)Straight running
26
Pitch = 25.4 mm (1.00 in.)Straight running
Pitch = 25.4 mm (1.00 in.)Straight running
36
41
46
Pitch = 25.4 mm (1.00 in.)Straight running
Pitch = 25.4 mm (1.00 in.)Side flexing
uni M-SNB M3
uni Light
32uni S-MPB Single Link®
uni QNB
uni CNB
uni Flex SNB
Contents
20000 40000 60000
Strength Index (POM)
20000 40000 60000
19000 N/m (1302 lb/ft)
Strength Index (POM)
20000 40000 60000
15000 N/m (1028 lb/ft)
Strength Index (POM)
20000 40000 60000
10250 N/m (702 lb/ft)
Strength Index (POM)
20000 40000 60000
23500 N/m (1610 lb/ft)2000 N/m (137 lb/ft)
Strength Index (POM)
20000 40000 60000
35000 N/m (2398 lb/ft)
Strength Index (POM)
20000 40000 60000
15700 N/m (1076 lb/ft)
Strength Index (POM)
20000 40000 60000
Standard
Standard
Standard Standard
Standard
Standard
Standard Standard
30000 N/m (2055 lb/ft)
5
56
Pitch = 25.4 mm (1.00 in.)Straight running
69
Pitch = 38.1 mm (1.50 in.)Straight running
73
Pitch = 38.1 mm (1.50 in.)Straight running
uni SNB M2
uni SSB
uni Light EP
77
Pitch = 50.0 mm (1.97 in.)Straight running
Pitch = 50.0 mm (1.97 in.)Straight running
82
uni L-SNB
uni OPB
Pitch = 50.8 mm (2.00 in.)Straight running
88uni CPB
Strength Index (POM)
20000 40000 60000
23500 N/m (1610 lb/ft)
Strength Index (POM)
20000 40000 60000
36000 N/m (2467 lb/ft)
Strength Index (POM)
20000 40000 60000
10250 N/m (702 lb/ft)
Strength Index (POM)
20000 40000 60000
55000 N/m (3768 lb/ft)
Strength Index (POM)
20000 40000 60000
22000 N/m (1507 lb/ft)
Strength Index (POM)
20000 40000 60000
52000 N/m (3563 lb/ft)
Standard US
Standard
Standard
Standard
Standard
Standard
Pitch = 50.8 mm (2.00 in.)Straight running
93uni MPB
Strength Index (POM)
20000 40000 60000
27500 N/m (1884 lb/ft)
Standard
Pitch = 63.5 mm (2.50 in.)Straight running
102uni X-MPB
Strength Index (POM)
20000 40000 60000
37500 N/m (2570 lb/ft)
Standard
106uni XLB
Pitch = 63.5 mm (2.50 in.)Straight running
Strength Index (POM)
20000 40000 60000 80000 100000
100000 N/m (6900 lb/ft)
Standard
62
Pitch = 38.1 mm (1.50 in.)Side flexing
uni Flex ONE
Strength Index (POM)
20000 40000 60000
(20000 N/m (1370 lb/ft) converted)
Standard
6
111
Pitch = 12.7 mm (0.50 in.)Straight running
Pitch = 19.1 mm (0.75 in.)Straight running
112
uni M-SNB M2
uni Light
Pitch = 25.4 mm (1.00 in.)Side flexing
115
Pitch = 38.1 mm (1.50 in.)Straight running
117
Pitch = 38.1 mm (1.50 in.)Straight running
123
uni Flex SNB
uni Light EP
122uni SSB
uni OPB
Pitch = 50.0 mm (1.97 in.)Straight running
128uni CPB
Pitch = 50.8 mm (2.00 in.)Straight running
Strength Index (POM)
20000 40000 60000
15000 N/m (1028 lb/ft)
Strength Index (POM)
20000 40000 60000
10250 N/m (702 lb/ft)
Strength Index (POM)
20000 40000 60000
30000 N/m (2055 lb/ft)
Strength Index (POM)
20000 40000 60000
Strength Index (POM)
20000 40000 60000
36000 N/m (2467 lb/ft)
Strength Index (POM)
20000 40000 60000
22000 N/m (1507 lb/ft)
Strength Index (POM)
20000 40000 60000
52000 N/m (3563 lb/ft)
Made-To-Order
Made-To-Order
Made-To-Order
Made-To-Order
Made-To-Order
Made-To-Order
Made-To-Order
130
132
134
135
Back cover
Fold-outflap on the frontcover
Application Data sheet (Metric)
Application Data sheet (Imperial)
Disclaimer
Warnings
Sales Organization
Legend
116
Pitch = 25.4 mm (1.00 in.)Straight running
uni SNB M2
Strength Index (POM)
20000 40000 60000
23500 N/m (1610 lb/ft)
Made-To-Order
110 - 128Made-To-Order Belts
10250 N/m (lb/ft)
129uni Retainer Rings
7
1/ Max temperature in water +60°C (+140°F).2/ Avoid impact below +8°C (+46°F).3/ Dry. Wet and hot applications use PPHW.Please, note that the temperature does have an effect on the mechanical properties of the belts.4/ POM-D/DI/LF/SLF/NL/S/SX
Material GradesTemperature range
Load
FDA
AR - Glass reinforced polypropylene +1 to +80 +33 to +176
POM - Polyoxymethylen4/ -40 to +90 -40 to +194
POM-EC - Electrical conductive materials -40 to + 90 -40 to +194
POM-AS/NLAS - Semi conductive materials -40 to + 90 -40 to +194
PA6.6 - Polyamide -40 to +140 -40 to +284
PA6 - Polyamide
PVDF - Polyvinylidenfluoride
FR - Flame Retardant Polyamide
-40 to +120
-40 to +100
+1 to +104
-40 to +248
-40 to +212
+34 to +219
Permissible load index
50% POM
100% POM
50% POM
100% POM
100% POM
100% POM
100% POM
90% POM
✔✔
✔✔
POM-DK - Polyoxymethylen -40 to +90 -40 to +194 100% POM -
PP - Polypropylene2/ 3/ +1 to +104 +34 to +219 100% PP
-
PE - Polyethylene -50 to +80 -58 to +176 100% PE
✔✔
GR - Glass reinforced polyester1/ -40 to +125 -40 to +257 70% POM
✔✔
--
PPMI - Metal detectable polypropylene -10 to +80 +14 to +176 70% PP
✔✔
PP-I - Polypropylene -10 to +80 +14 to +176 80% PP ✔✔
PEMI - Metal detectable polyethylene -50 to +80 -58 to +176 80% PE
✔✔PPHW - Hot water polypropylene +1 to +104 +34 to +219 100% PP
-
✔✔
PA6.6H - Polyamide -40 to +160 -40 to +320 100% POM -
✔✔
PA6-GF - Polyamide Glass Reinforced -40 to +120 -40 to +248 100% POM -
✔✔
-
°C °F
uni Belt Material Selection
POM-DPOM polymers with self-lubricating components.
POM - Polyoxymethylen POM is a thermoplastic material with very good mechanical and thermal properties. The material can also be characterized by great strength, elasticity and dimensional stability. POM is resistant to a wide selection of chemicals. POM has good bearing qualities, low coefficient of friction and a good resistance to wear.
B BR D DG E G K N O P T W YColor options:
POM-LFPOM polymers with improved self-lubricating components.
POM-DIPOM polymers with self-lubricating components and improved impact resistance.
B BR D DG E G K N O P T W YColor options:
POM-DKPOM-DK is a reinforced POM polymer designed for applications where high wear resistance is needed and/or high con-veyor speeds are required. The material is typically used for wear parts on side flexing belt or in applications where veryhigh wear resistance is required.
O KColor options:
B BR D DG E G K N O P T W YColor options:
POM-AS - Semi conductive materials Semi conductive POM with self-lubricating components is used in applications where you want to avoid build-up of static electricity. POM-AS is normally used for manrider belts to avoid discomfort; it can also be used in applications where youwant to avoid products (such as thin plastic foils) "sticking" to the belt/chain.uni-chains® standard POM-AS holds a surface resistivity of 1 x 1011 Ohm according to IEC 60093/ASTM D257.
8
POM-NLPOM polymers with no lubricant that can be used for applications where you want to ensure that no lubricant may affect theproduct adhesion or the like.uni-chains® standard POM-NL holds a surface resistivity of minimum 1 x 1014 Ohm according to IEC 60093/ASTM D257.
PP - Polypropylene Polypropylene is a thermoplastic material with very good chemical resistance properties. PP is an economical material forapplications with high temperatures.
uni Belt Material Selection
POM-SLFPOM polymers with self-lubricating additives to obtain the lowest possible friction resistance.
B BR D DG E G K N O P T WColor options:
POM-NLASPOM polymers which contains no lubricant and contains additives that reduce the electrical resistance, thereby helping to dissipate static electricity.POM-NLAS holds a surface resistivity of 1 x 1011 Ohm according to IEC 60093/ASTM D257.
POM-SPOM polymers which contains low noise components, mainly used for the new uni Snap Link® without pins.
GKColor options:
KColor options:
KColor options:
B BR D DG E G K N O P T W YColor options:
Color options:
PP-IPP with improved impact resistance and improved properties at low temperatures. Use of PP-I in hot water should be avoided.
B D E G K N O P T W Y
Color options: B D E G K N O P T W Y
POM-EC - Electrical conductive materialsElectrical conductive POM is normally used in explosive areas where sparks and static must be avoided, such as areas with fil-ling aerosol, camping gas, or the like. uni-chains® standard EC holds a surface resistivity of 1 x 106 Ohm according to IEC 60093/ASTM D257.
Color options: K
Y
Y
Y
POM-SXPOM polymers with self-lubricating components.POM-SX will be the right solution where the demand is lower friction, higher load and lower noise compared to standardPOM. POM-SX will mainly be used for high load capacity uni Snap Link® without pins.
WColor options:
Color options:
GR - Glass Reinforced PolyesterGlass reinforced polyester is a material with an extremely high resistance to wear and heat.
Color options:
9
FR - Flame Retardant Polyamide Flame retardant polyamide is a fire restricting material used in surroundings where there is a danger of the chain being ignited.The FR material is rated as V-0 which is the best classification according to UL 94 standard to avoid burning.
Color options: N
PVDF - Polyvinylidenfluoride Polyvinylidenfluoride is characterized by an especially high chemical resistance. Furthermore, PVDF has high wear resistanceand good friction properties.
Color options: N
Metal detectable polypropylene – PPMI PPMI is a metal detectable polypropylene with improved impact resistance to allow detection with both metal detectors andX-ray machines in case of belt breakage. PPMI is used to increase safety in food processing equipment which will allow theuser to detect if pieces of plastic from upstream conveyors have contaminated the conveyed product.
Color options: DB DD
PPHW - Hot water polypropylene PPHW is a polypropylene which contains additives that reduce decomposition over time due to oxidization caused by metalions in hot water applications like blanchers and cookers.
Color options: B D E G K N O P T W Y
PE - PolyethylenePE is used in low temperature applications and where high impact resistance is required.
Color options: B D E G K N O P T W Y
PE-IPE with improved impact resistance.
Color options: B D E G K N O P T W Y
uni Belt Material Selection
B K W
K N
AR - Glass Reinforced Polypropylene AR is an acid resistant material which is used where very high chemical resistance is required. The limited mechanical strengthof polypropylene is considerably improved by the glass fiber reinforcement.
PEMI - Metal detectable polyethylene PEMI is a metal detectable polyethylene with improved impact resistance to allow detection with both metal detectors and X-ray machines in case of belt breakage. PEMI is used to increase safety in food processing equipment which will allow youto detect if pieces of plastic from upstream conveyors have contaminated the conveyed product.
Color options: DB
10
PA6.6 - Polyamide Polyamide PA6.6 is a thermoplastic material with many fine properties. The material has a high resistance to wear, high strengthand great stiffness. Furthermore, polyamide has a large temperature range.
Color options: B D N W
Note: PA materials will absorb water in wet environments which will cause expansion of the dimension with approx. 1-2 %, depending on the temperature level and the humidity of the air.
PA6.6-HPA6.6-H is a polyamid which contains the same fine properties as PA6.6. The PA6.6-H improves upon PA6.6 in applications where higher temperature resistance is needed e.g. shrink tunnels.
Color options: B D N W
Austenitic Stainless Steel
Austenitic quality containing 18% chrome and 8% nickel.Werkstoff no. 1.4301AISI 30418/8 CrNi steel is non-magnetic in the entire recommended temperature range. The austenitic quality has a very high degree of corrosion resistance in oxidizing surroundings. However, in connection with evaporation of chloride-containing fluids, the18/8 CrNi steel is not recommended, as stress corrosion can occur over time.
SS304
uni Belt Material Selection
The UV stabilizer is an additive recommended for plastic materials used for outdoor applications. The UV stabilizer is able toprotect materials against direct sunlight to avoid destruction thereof. The UV stabilizer is FDA approved and will increase thelifetime of plastic materials. The UV stabilizer is available for the most common materials such as POM, PP and PE.
UV - Ultraviolet stabilizer
uni Pin Material Selection
PA6-GF - Polyamide Glass ReinforcedThis Polyamide is reinforced with glass fiber. PA6-GF will be the right solution where higher stiffness and higher strength isrequired, compared to standard Polyamide. The combination of mechanical properties and chemical resistance makes this material suitable for many situations. Polyamide has a high resistance to wear and dynamic loads. Polyamide has also a lagerworking temperature range.
Color options: B K
PA6 - Polyamide Polyamide PA6 is a thermoplastic material. The combination of mechanical properties and chemical resistance makes this material suitable for many situations. Polyamide has a high resistance to wear and dynamic loads. This material is primarily usedfor sprockets.
Color options: B D K N T W
11
Rubber colorRubber code
Natural
Black
Ivory
60
60
85
-40 to +80°C
-40 to +80°C
-40 to +80°C
-40 to +176°F
-40 to +176°F
-40 to +176°F
✔✔
-
✔✔
Hardness(shore A)
Temperature range
°C °F
FDAapproved
Co-moulding
Co-moulding
Mechanical
Attachment to baselink
Natural 64 -40 to +125°C -40 to +257°F ✔✔ Mechanical01 N
03 N
03 K
05 I
Austenitic Stainless Steel
Austenitic quality containing 18% chrome, 10% nickel and 3% molybdenumWerkstoff no. 1.4404AISI 316
18/10 CrNi steel with molybdenum is non-magnetic in the entire recommended temperature range. The austenitic quality has a very high degree of corrosion resistance in oxidizing surroundings. Molybdenum has been added to increase corrosion resistance particulary in chloride containing environments.
SS316
uni Reinforcement Material Selection
uni Rubber Material Selection
uni Pin Material Selection
PA6.6 - PolyamidePolyamide PA6.6 is a thermoplastic material with many fine properties. The material has a high resistance to wear, high strengthand great stiffness. Furthermore, polyamide has a large temperature range.
GR - Glass Reinforced Polyester Glass reinforced polyester is a material with an extremely high resistance to wear and heat.
Austenitic Stainless Steel
Austenitic quality containing 18% chrome, 10% nickel and 3% molybdenumWerkstoff no. 1.4404AISI 316
18/10 CrNi steel with molybdenum is non-magnetic in the entire recommended temperature range. The austenitic quality has a very high degree of corrosion resistance in oxidizing surroundings. Molybdenum has been added to increase corrosion resistance particulary in chloride containing environments.
SS316
PP - Polypropylene Polypropylene is a thermoplastic material with very good chemical resistance properties. PP is an economical material forapplications with high temperatures.
PE - Polyethylene PE is used in low temperature applications and where high impact resistance is required.
12
USDA (US Department of Agriculture)USDA evaluates and accepts products and equipment for use in the dairy, meat, and poultry industries. uni-chains belting products listed on this page are listed in the USDA's Accepted Meat and Poultry Equipment book as accepted for food contact and packaged goods respectively. In addition, USDA inspectors accept belt styles on an individualplant basis.
USDA Dairy Grading Branch has issued Equipment Acceptance Certificates for the belt types listed on this page under USDA Dairy Accepted.
USDA Accepted Meat and Poultry Equipment (Food Contact)• uni SNB series• uni OPB 4C, uni OPB 4V C, uni OPB 4V 23%, uni OPB 4V 36%, uni OPB 8C and uni OPB 8 25%
USDA Accepted Meat and Poultry Equipment (Packaged Product only)All the above plus uni Light.
USDA Dairy Accepted• uni MPB, uni MPB-G, uni MPB-GE, uni MPB-N, uni MPB-NE, uni MPB 18%, uni MPB 20%, uni MPB 22%• uni CNB C, uni CNB 18%, uni CNB 22%
USDA Equipment Acceptance Certificate in compliance with NSF - 3A - 14159 - 003: Hygiene requirementsfor design of mechanical belt conveyors used in meat and poultry processing.The acceptance covers the following products:• uni MPB Single Link® and bricklayed belts• uni MPB Product Supports and Side Guards• uni MPB Sprockets
Approvals
FDA (US Food and Drug Administration)US Federal Agency that approves materials for use with food contact.
uni-chains® uses FDA approved materials of the following types:• POM-D, POM-DI, POM-LF, POM-SLF, POM-NL and POM-S• PP, PP-I, PPMI, PPHW• PE, PE-I, PEMI• PVDF• PA6, PA6.6• UV additive
14
ST
AN
DA
RD
uni M-PNB M1
uni M-PNB M1 – a new pinless design beltThis new pinless design is an exclusive uni-chains® 0.5 in. pitch belt including the new Snap Link® feature. An open belt with no pin makes assembly and disassembly an exceptionally simple operation. The design of Mini PNB(uni M-PNB M1) provides the maximum amount of open area for drainage and airflow with minimum product contact. The belt reduces dirt/debris compared to e.g. a wire mesh belt.
The uni M-PNB M1 belt with its unique features is the perfect belt in the following industries/applications:- Bakery applications including cooling lines, freezing lines and icing lines- Poultry applications including grading lines- Seafood applications including grading lines and weighing lines
Product features and operational Benefits:- Easy to clean – reduced downtime for cleaning- Small transfer – nose bar applications- Snap Link® feature reduces maintenance and downtime- Snap Link® feature eliminates pin walking and pins coming out - Snap Link® feature increases belt weight consistency
Pitch 12.7 mm (0.50 in.)
New
15
TypeStandard materials
and colors
uni M-PNB M1 WBPOM-S
Standard Materials and Colors
Surface opening 40%
ST
AN
DA
RD
uni M-PNB M1
Standard Selection
uni M-PNB M1Materials
12.7 mm (0.50 in.)
See page 7 and 8
Patent Patent pending
Straight running
See page 17
See page 129
12.5 mm (0.49 in.)
uni M-PNB M1
Dimensional Sketch
T
P
6.4
12.7
mm
0.25
0.50
in.
Dimensions
Travel*
P
T * Travel in both directions is possible.uni-chains® recommends this traveldirection.
51
102
152
203
254
305
356
406
457
508
2.0
4.0
6.0
8.0
10.0
12.0
14.0
16.0
18.0
20.0
559 22.0
609 24.0
mm in. mm in. mm in. mm in. mm in.
660 26.0
711 28.0
762 30.0
812
863
914
965
1015
1066
1117
1168
1218
32.0
34.0
36.0
38.0
40.0
42.0
44.0
46.0
48.0
1269 50.0
1320 52.0
1371 54.0
1421 55.9
1472 58.0
1523 60.0
1573
1624
1675
1726
1776
1827
61.9
63.9
65.9
68.0
69.9
71.9
1878
1929
1979
2030
73.9
75.9
77.9
79.9
2081 81.9
2132 83.9
2182 85.9
2233 87.9
2284 89.9
2335
2385
2436
91.9
93.9
95.9
2487
2538
2588
2639
2690
2741
2791
97.9
99.9
101.9
103.9
105.9
107.9
109.9
2842 111.9
2893 113.9
2944 115.9
2994 117.9
3045 119.9
Standard Bricklayed Belt Widths (See next page for Single Link® widths)
16
ST
AN
DA
RD
uni M-PNB M1
uni M-PNB M1 Single Link®
uni M-PNB M1 Single Link® is available in the following standard widths:
K200 (50.5 mm (1.99 in.))
K400 (101.3 mm (3.99 in.))
K1200 (304.5 mm (11.99 in.))
137*2000*uni M-PNB M1
POM
Permissible Tensile StrengthBelt material
lb/ftN/m
0.924.5uni M-PNB M1
POM
Belt WeightsBelt material
lb/ft2kg/m2
* Please note: strength reduction if:- non-compliance with recommended sprocket distance- use of nosebar
B
A
C
B min.
A min.
5.0
25.0
0.20
C min. 46.0 1.81
0.98
mm in.
Nosebars
Min. dimensions
100
60
ø25 mm(~1 in.)
ø65 mm(~2.5 in.)
DiameterA
% of permissible tensile strength
Reduction of strength
17
ST
AN
DA
RD
uni M-PNB M1
Standard Sprockets
0.9825.01.3434.01.3133.28 8333MPNB08N
in.mmin.mmin.mm
Hub diameterOverall diameterPitch diameterNo. ofteeth
1.1830.01.6742.41.6241.110 8333MPNB10N
1.7745.02.3259.02.2557.114 8333MPNB14N
2.1755.02.8171.32.7269.117 8333MPNB17N
2.5665.03.1379.53.0477.219 8333MPNB19N
2.9575.0
2.9575.0
3.78*96.0*
3.9399.83.8397.324 8333MPNB24N
4.57116.14.46113.4288333MPNB28N
8333MPNB28NBB*
2.9575.0
4.72*120.0*5.85148.55.74145.736
8333MPNB36N
8333MPNB36NBB*
Reference no.plastic
in.mm
Max. round bore
No. ofteeth
0.9825.010
1.5740.014
1.9750.017
2.3660.019
2.7670.024
2.7670.0
3.54*90.0*
2.7670.0
4.53*115.0*
28
36
in.mm
Max. square bore
0.5915.0
1.0025.4
1.1830.0
1.5740.0
1.7745.0
1.7745.0
2.36*60.0*
1.7745.0
3.00*76.2*
in.mm
0.7920.08 0.5915.0 0.6316.0
0.7920.0
1.3835.0
1.5740.0
2.0050.8
2.3660.0
2.3660.0
3.15*80.0*
2.3660.0
3.94*100.0*
Width of sprockets: 20.0 mm (0.79 in.)Tooth width: 12.0 mm (0.47 in.)
uni M-PNB M1 sprocket
PA6 N
Other sprocket sizes are available upon request. Two-part sprockets available upon request.
Please contact uni-chains® for further information.
Standard Material and Color
* BB = Big boss.
* BB = Big boss.
No. of
teeth mm in. mm in.
8
10
14
17
19
24
28
12.2
16.4
20.2
24.0
31.9
37.9
41.9
52.0
60.0
0.80
0.94
1.26
1.49
1.65
2.05
2.36
24.6
30.8
35.9
45.1
53.2
0.48
0.65
0.97
1.21
1.37
1.78
2.09
36 76.1 3.00 69.4 2.73
Minimum B-dimension
Wearstrip distance A
A
B
Placement of Wearstrips and Sprockets
Bore + keyway
18
ST
AN
DA
RD
uni M-QNB
Pitch 12.7 mm (0.50 in.)
uni M-QNB – the high speed and tight transfer belt The uni Mini QNB (uni M-QNB) is a belt developed for tight transfer and high speed conveyors in both food and non food industries. The 0.5 in. pitch, bi-directional belt ensures product stability even in nose bar and high speed applications due to the rounded bottom surface.
The uni M-QNB belt increases performance in the following industries/applications:- Bakery applications including dough handling, general conveyance and packaging lines- Meat applications including tray pack lines and metal detectors- Seafood applications including grading lines and weighing lines- Beverage applications including depalletizers, accumulation tables and acceleration lines- Can manufacturing applications including palletizers, mass handling and accumulation tables- Corrugated applications including downstacker, corrugator take off, transfer car and WIP storage
Product features and operational benefits:- Less vibration in high speed and nosebar applications- Wear resistance in high speed applications with tight transfers- Strong bi-directional belt for longer conveyors- Unique locking system (lockpin) for easy maintenance- Unique sprocket engagement reduces pulsation- Unique Rubber Top eliminates wear and increases friction in incline or acceleration applications
19
ST
AN
DA
RD
uni M-QNB
NK03 See page 11
Materials
12.7 mm (0.50 in.)
See page 7 and 8
Straight running
See page 21
20 mm (0.8 in.)
uni M-QNB C
uni M-QNB Vacuum
uni M-QNB Rubber Top uni M-QNB Rubber Top
Standard Selection
uni M-QNB, Vacuum
Dimensional Sketches
Travel
P
TL
E
uni M-QNB Rubber Top
P
T
L
P
T
E
4.4
12.7
8.8
5.1
0.17
0.50
R 2.2 0.09
0.35
0.20
mm in.
L
R
E
Travel
76
152
228
304
3803.0
6.0
9.0
12.0
15.0
456
531
607
683
75918.0
20.9
23.9
26.9
29.9
835
912
988
1063
113932.9
35.9
38.9
41.9
44.8
1216
1292
1368
1443
151947.9
50.9
53.9
56.8
59.8
1595
1670
-
-
62.8
65.7
-
-
Standard Bricklayed Belt Widths (See next page for Single Link® widths)
mm in. mm in. mm in. mm in. mm in. mm in.
Dimensions
Patent Patent pending
Vacuum holes: ø3.2 mm (0.12 in.)
Standard materials and colors
Pins
Materials and colors
Standard Materials and Colors
uni M-QNB C B
PP
PE
NPA6.6
NPA6.6
POM-SLF DPA6.6
Type
W
PP PA6.6G
N
POM-EC PA6.6K
uni M-QNB Rubber Top PA6.6
NPA6.6
D
DGPP +
WPP N03+
uni M-QNB Vacuum DPA6.6PP
K03
D
G
See page 129
20
ST
AN
DA
RD
uni M-QNB
uni M-QNB Single Link®
uni M-QNB is available as Single Link® in thefollowing standard widths:
K300 (75.8 mm (2.98 in.))
K600 (152.0 mm (5.98 in.))
130219000uni M-QNB
POM
--
PA6.6
1.688.2uni M-QNB
POM PP
--
1.256.1
1.296.3
Permissible Tensile Strength
lb/ftN/m
89113000
PP
89113000
PA6.6
lb/ftN/m
5488000
PE
--
PA6.6
lb/ftN/m
99314500
EC
--
PA6.6
lb/ftN/m
Belt material
Pin material
uni M-QNB Rubber Top
Belt Weights
lb/ft2kg/m2
PA6.6Pin material
lb/ft2kg/m2
PA6.6
PE
1.215.9
--
lb/ft2kg/m2
PA6.6
EC
1.547.5
--
lb/ft2kg/m2
PA6.6
uni M-QNB Rubber Top
Belt material
Nosebars
B
A
C
B min.
A min.
4.0
20.0
0.16
C min. 41.6 1.64
0.79
mm in.
Min. dimensions
21
ST
AN
DA
RD
uni M-QNB
Standard Sprockets
1.1028.01.6341.51.65 41.810 2233MSNB210N
in.in. mmmmin.mmin.mm
Hub diameterOverall diameterPitch diameterNo. ofteeth
ø0.39/0.71*ø10.0/18.0*
2.5665.03.1179.03.0978.519
2233MSNB219Nø0.75/1.57*ø19.1/40.0*
2233MSNB219N10INSQsq 1.00sq 25.4
2233MSNB219N15INSQsq 1.50sq 38.1
2233MSNB219N40MMSQsq 1.57sq 40.0
2.5665.0
4.57116.24.54115.428
2233MSNB228Nø0.75/1.57*ø19.1/40.0*
2233MSNB228N15INSQsq 1.50sq 38.1
2233MSNB228N40MMSQsq 1.57sq 40.0
3.94100.02233MSNB228NBBø1.57/2.76*ø40.0/70.0*
2233MSNB228NBB60MMSQsq 2.36sq 60.0
2.9575.06.20157.46.16156.438
2233MSNB238Nø0.75/1.57*ø19.1/40.0*
2233MSNB238N15INSQsq 1.50sq 38.1
2233MSNB238N40MMSQsq 1.57sq 40.0
3.94100.0 2233MSNB238NBBø1.57/2.76*ø40.0/70.0*
Reference no.plastic
Bore
Belt material POM
N lb N lb
uni M-QNB 1000 225 800 180
Max. Load per SprocketPP
Width of sprockets: 20.0 mm (0.79 in.)Tooth width: 7.0 mm (0.28 in.)
uni M-QNB sprocket
PA6 N
Other sprocket sizes are available upon request. Two-part sprockets available upon request.
Please contact uni-chains® for further information.
* Minimum/maximum round bore.
Standard Material and Color
No. of
teethmm in. mm in.
10
19
28
38
15.4
34.2
25.2
43.5
62.0
82.4
0.99
1.71
2.44
3.24
52.8
73.8
0.61
1.35
2.08
2.89
Minimum B-dimension
Wearstrip distance A
A
B
Placement of Wearstrips and Sprockets
22
uni M-SNB M3
uni M-SNB M3 – strong and small pitch beltThe uni Mini SNB M3 (uni M-SNB M3) is a belt developed for tight transfer, high speed and low profile conveyors inboth food and non food industries. The 0.5 in. pitch, bi-directional belt ensures product stability even in nose bar and high speed applications due to the rounded bottom surface.
The uni M-SNB M3 belt increases performance in the following industries/applications:- Bakery applications including general conveyance, cooling lines, metal detectors and packaging lines- Meat applications including tray pack lines and metal detectors- Seafood applications including sorting lines and weighing scales- Beverage applications including depalletizers and accumulation tables- Can manufacturing applications including palletizers, mass handling, transfer conveyors, discharge conveyors and
accumulation tables
Product features and operational benefits:- Less vibration in high speed and nosebar applications- Wear resistance in high speed applications with tight transfers- Strong bi-directional belt for longer conveyors- Unique locking system (lockpin) for easy maintenance- Unique sprocket engagement reduces pulsation- Open (flat) top surface increases product stability and reduces back line pressure
Pitch 12.7 mm (0.50 in.)
ST
AN
DA
RD
23
uni M-SNB M3
uni M-SNB M3
TL
E
P
WPE
TypeStandard materials
and colors
Standard pins
Materials and colors
Standard Materials and Colors
uni M-SNB M3
W
DPA6.6
BRPOM-LF
NPA6.6WPP
BPOM-D
Standard Bricklayed Belt Widths (See next page for Single Link® widths)
76
152
228
304
381
456
533
608
685
762
3.0
6.0
9.0
12.0
15.0
18.0
21.0
23.9
27.0
30.0
837
914
990
1066
1142
1218
1294
1370
144633.0
59.936.0
62.939.0
65.942.0
68.945.0
71.948.0
50.9
53.9
56.9
1522
1598
1674
1750
1826
1902
1978
2054
2130
2206
2282
2358
2434
mm in. mm in. in.mm mm
74.9
77.9
80.9
83.9
86.9
89.8
92.8
95.8
in
2510
2586
2662
2738
2814
2890
2966
3042
mm
98.8
101.8
104.8
107.8
110.8
113.8
116.8
119.8
in.
SS304BPA6.6
Surface opening 14%
N01 See page 11
NPA6.6
uni M-SNB M3
Dimensional Sketch
Travel
Alternatives
L
T
E
4.4
8.8
5.1
mm
0.17
P 12.7 0.50
0.35
0.20
in.
Dimensions
ST
AN
DA
RDStandard Selection
Patent Patented
NPA6.6NPE
D
BPP
PA6.6
12.7 mm (0.50 in.)
See page 7 and 8
Straight running
20 mm (0.8 in.)
See page 25
See page 129
Materials
24
B
1.296.3uni M-SNB M3
POM
1.768.6 0.844.1
PP
1.155.6 0.904.4
PE
1.215.9
Belt Weights
lb/ft2kg/m2
plasticPin material
lb/ft2kg/m2
steel
lb/ft2kg/m2
plastic
lb/ft2kg/m2
steel
lb/ft2kg/m2
plastic
lb/ft2kg/m2
steel
Belt material
N01
Rubber inserts can be assembled in any pattern on belt surface per customer’s request.
uni M-SNB M3
102815000uni M-SNB M3
POM
5147500
PP
Permissible Tensile Strength
lb/ftN/m lb/ftN/m
3084500
PE
lb/ftN/m
Belt material
uni M-SNB M3 Rubber Inserts uni M-SNB M3 Rubber Inserts
Standard Selection Accessories Dimensional Sketch
A C
B
A
8.0
14.0
mm
0.31
C 3.0 0.12
0.55
in.
Dimensions
ST
AN
DA
RD uni M-SNB M3 Single Link®
uni M-SNB M3 is available as Single Link® in the following standard widths:
K600 (152.4 mm (6.00 in.))
K300 (76.1 mm (3.00 in.))
Standard Material and Color
B min.
A min.
4.0
20.0
0.16
C min. 41.6 1.64
0.79
mm in.
Nosebars
Min. dimensions
B
A
C
25
uni M-SNB M3
ST
AN
DA
RDStandard Sprockets
1.1028.01.6341.51.65 41.810 2233MSNB210N
in.in. mmmmin.mmin.mm
Hub diameterOverall diameterPitch diameterNo. ofteeth
ø0.39/0.71*ø10.0/18.0*
2.5665.03.1179.03.0978.519
2233MSNB219Nø0.75/1.57*ø19.1/40.0*
2233MSNB219N10INSQsq 1.00sq 25.4
2233MSNB219N15INSQsq 1.50sq 38.1
2233MSNB219N40MMSQsq 1.57sq 40.0
2.5665.0
4.57116.24.54115.428
2233MSNB228Nø0.75/1.57*ø19.1/40.0*
2233MSNB228N15INSQsq 1.50sq 38.1
2233MSNB228N40MMSQsq 1.57sq 40.0
3.94100.02233MSNB228NBBø1.57/2.76*ø40.0/70.0*
2233MSNB228NBB60MMSQsq 2.36sq 60.0
2.9575.06.20157.46.16156.438
2233MSNB238Nø0.75/1.57*ø19.1/40.0*
2233MSNB238N15INSQsq 1.50sq 38.1
2233MSNB238N40MMSQsq 1.57sq 40.0
3.94100.0 2233MSNB238NBBø1.57/2.76*ø40.0/70.0*
Reference no.plastic
Bore
Belt material POM
N lb N lb
uni M-SNB M3 1000 225 800 180
Max. Load per SprocketPP
Width of sprockets: 20.0 mm (0.79 in.)Tooth width: 7.0 mm (0.28 in.)
uni M-SNB M3 sprocket
PA6 N
Other sprocket sizes are available upon request. Two-part sprockets available upon request.
Please contact uni-chains® for further information.
* Minimum/maximum round bore.
Standard Material and Color
No. of
teethmm in. mm in.
10
19
28
38
15.4
34.2
25.2
43.5
62.0
82.4
0.99
1.71
2.44
3.24
52.8
73.8
0.61
1.35
2.08
2.89
Minimum B-dimension
Wearstrip distance A
A
B
Placement of Wearstrips and Sprockets
26
ST
AN
DA
RD
uni Light
uni Light – unique belt for light duty applicationsThe uni Light belt was designed for applications with high volume production, accumulation and where a smooth transferbetween conveyors is needed.
The uni Light (Closed and Open Surface) belts have increased performance in the following industries/applications:- Paper/tissue applications including diverters, accumulation tables and wrapping applications- Beverage applications including depalletizers, palletizers, accumulation tables and acceleration lines- Can manufacturing applications including palletizers, mass handling and accumulation tables- Material handling applications including takeaway and incline conveyors- Fruit & vegetable applications including inspection tables, elevators and incline conveyors- Bakery applications including cooling lines, dough handling and tray conveyors
Product features and operational benefits:- Small pitch for high speed and small transfer applications- Easy maintenance and less downtime with unique locking system (lockpin)- Unique openings for high performance (e.g. 10% opening for cherries with stems)- Flat surface for high stability (e.g. raw edge can manufacturing)- High friction Rubber Top for diverters or incline conveyors
Pitch 19.1 mm (0.75 in.)
27
uni Light
ST
AN
DA
RD
uni Light C uni Light 10% uni Light 22%
Standard Selection
uni Light C, 10%, 22%
Dimensional Sketches
uni Light Rough Rubber Top
E
L
T
A
5.1
4.3
8.5
2.0
0.20
0.17
P 19.1 0.75
0.33
0.08
mm in.
Dimensions
uni Light Rough Rubber Top
K03
W WPP PE
SS304B
NGR
NPA6.6
See page 11
19.05 mm (0.75 in.)
See page 7, 8 and 9
Straight running
See page 29
Materials
25 mm (1.0 in.)uni Light Rib: 50 mm (2.0 in.)
See page 30
Accessories
See page 31
See page 30
See page 114
Alternatives
E
Travel Travel
E
A
P
L L
P
T T
Standard locksType
Standard materials and colors
Standard pins
Materials and colors Materials and colors
DPA6.6uni Light C
uni Light 10%
uni Light 22%
K
B
K
GWPP
PP
GPPPA6
DPA6.6
DPA6.6
NGR
NPA6.6
BRPOM-LF
DPA6.6BRPOM-LF
DPA6.6PP
uni Light Rough Rubber Top KPP K03+ DPA6.6
Standard Materials and Colors
W
BRPOM-LF
Indent for uni Light Rough Rubber Top is 15.0 mm (0.59 in.).
Patent Patented
G
See page 129
28
ST
AN
DA
RD
uni Light
76
153
229
306
382
458
535
611
687
764
3.0
6.0
9.0
12.0
15.0
18.0
21.1
24.1
27.0
30.1
840
917
993
1070
1146
1223
1299
1375
1451
1528
33.1
36.1
39.1
42.1
45.1
48.1
51.1
54.1
57.1
60.2
1604
1681
1757
1834
1910
1987
2063
2139
2216
2292
63.2
66.2
69.2
72.2
75.2
78.2
81.2
84.2
87.2
90.2
2369
2445
2522
2598
2674
2751
2827
2904
2980
3057
93.3
96.3
99.3
102.3
105.3
108.3
111.3
114.3
117.3
120.4
mm in. mm in. mm in. mm in.
uni Light Single Link®
uni Light is available as Single Link® in the followingstandard widths:
K300 (76.4 mm (3.01 in.))
K450 (114.6 mm 4.51 in.))
K600 (152.8 mm (6.02 in.))
K225 (57.7 mm (2.27 in.))
Belt type and widths
uni Light C
uni Light 10%
K600 152.8 mm (6.02 in.)
X
K450 114.6 mm (4.51 in.)
X
K300 76.4 mm (3.01 in.)
X
K22557.7 mm (2.27 in.)
X
XX
uni Light 22% XX
uni Light Rough Rubber Top X
Standard Bricklayed Belt Widths (See below for Single Link® widths)
Standard Single Link® Belt Widths
29
Standard Sprockets
1.2231.01.6842.61.73 43.97 2833UL07N
in.in. mmmmin.mmin.mm
Hub diameterOverall diameterPitch diameterNo. ofteeth
ø0.63/0.79*ø16.0/20.0*
1.7745.02.4361.72.43 61.710
2833UL10Nø0.63/1.38*ø16.0/35.0*
1.9349.0 2833UL10N15HEXhex 1.50hex 38.1
2.5665.04.13105.04.08103.717
5.80147.35.75146.024
2833UL17Nø0.75/1.57*ø19.1/40.0*
2833UL17N40MMSQsq 1.57sq 40.0
2.7670.0
2833UL24Nø0.75/1.57*ø19.1/40.0*
2833UL24N15INSQsq 1.50sq 38.1
4.72120.0 2833UL24NBBø1.57/2.76*ø40.0/70.0*
2833UL24N40MMSQsq 1.57sq 40.0
6.04153.35.98152.0252.7670.0
2833UL25Nø0.75/1.57*ø19.1/40.0*
2833UL25N15INSQsq 1.50sq 38.1
2833UL25N40MMSQsq 1.57sq 40.0
4.72120.0 2833UL25NBBø1.57/2.76*ø40.0/70.0*
Reference no.plastic
Bore
uni Light
ST
AN
DA
RD
Width of sprockets: 25.0 mm (0.98 in.)Tooth width: 4.8 mm (0.19 in.)
uni Light sprocket
PA6 N
Other sprocket sizes are available upon request.
Two-part sprockets available upon request.
Please contact uni-chains® for further information.
* Minimum/maximum round bore.
Standard Material and Color
No. of
teethmm in. mm in.
7
10
17
24
15.4
25.0
26.3
35.2
56.2
77.3
1.04
1.39
2.21
3.04
46.6
67.0
0.61
0.98
1.83
2.64
25 80.3 3.16 71.0 2.80
Minimum B-dimension
Wearstrip distance A
A
B
Placement of Wearstrips and Sprockets
30
ST
AN
DA
RD
uni Light
70210250uni Light
POM
3515125
PP
Permissible Tensile Strength
lb/ftN/m lb/ftN/m
2113075
--uni Light Rough Rubber Top 3515125 --
PE
lb/ftN/m
Belt material
1.396.8uni Light C
POM
2.9114.2 0.984.8
PP
2.5012.2 1.004.9
PE
2.5412.4
1.276.2uni Light 10% 2.8113.7 0.884.3 2.4411.9 0.944.6 2.4812.1
1.135.5uni Light 22% 2.6613.0 0.803.9 2.3611.5 0.844.1 2.3811.6
--uni Light Rough Rubber Top -- 1.135.5 2.6613.0 -- --
Belt Weights
lb/ft2kg/m2
plasticPin material
lb/ft2kg/m2
steel
lb/ft2kg/m2
plastic
lb/ft2kg/m2
steel
lb/ft2kg/m2
plastic
lb/ft2kg/m2
steel
Belt material
uni Light Tab
Standard Selection Accessories Dimensions
H
K
G
15.9
11.9
3.5
mm
0.63
J 20.0 0.79
0.47
0.14
in.
POM-D
Standard Material and Color
Note: When using tabs please verify that sufficient clearanceto the shaft exists.Max. shaft diameter = Sprocket pitch diameter - 44.5 mm(1.75 in.).When using square shafts verify that the diagonal does notexceed above max. diameter.Example: Sprocket z = 17: Max. shaft diameter 103.7 - 44.5 = ø59 mm (4.08 - 1.75 = ø2.3 in.).
HK
G
J
Travel
W
P
A
BB
Travel
Tra
vel
uni Light Side Guard
Dimensions
B* min.
P
A
15.0
19.05
31.4
mm
0.59
C* min. 24.0 0.98
D* min. 25.0 0.98
0.75
1.23
in.
GPP-I
Standard Material and Color
W
C
D D
Standard Selection Accessories
C
* Increment: 9.5 mm (0.37 in.).
Please note that the tabs are not always placed in the middle of the belt.
31
uni Light
ST
AN
DA
RD
uni Light Product Support Flat (no Ribs)
Product Support with Indent
uni Light Product Support with Ribs
Product Support L-I15 (Left Indent)Product Support R-I15 (Right Indent)
Height
mm in.Style
Width
K300 76.4 3.01
152.8 6.02
152.8 6.02
152.8 6.02
152.8 6.02
K600
K600
Molded indent
Indent mm
Standard materials & colors
PP-I PA6 Rubber 04
1.00
flat (no ribs)
with ribs
25.4
50.8 2.00
76.2 3.00
with ribs K600
with ribs K600
W
GW
GW
GW
GW
W
G
G
no*
no*
no*
left
right
right
left
no*
GW
GW
GWright
left
no*
-
-
-
15.0
15.0
15.0
15.0
-
15.0
15.0
-
in.
-
-
-
15.0
0.59
0.59
0.59
-
0.59
0.59
-
K
K
K
K
K
K
K
K
Type mm in.
Product Support
Dimensional Sketch
Travel
Standard Materials, Colors and Dimensions
Standard Selection Accessories
* Minimum bricklaid indent for uni Light product support is 38.1 mm (1.50 in.).Increment: 19.1 mm (0.75 in.).
32
ST
AN
DA
RD
uni S-MPB
uni S-MPB – strong and cleanable 1 in. pitch beltThe uni Small MPB (uni S-MPB) belt is a strong and cleanable belt used in various food applications. The reinforcement bar on the underside ensures high impact resistance. The S-MPB belt is available in the unique Single Link® belt with aSingle Link® product support for optimal cleaning.
The uni S-MPB belt is the preferred belt in the following industries/applications:- Meat (beef & pork) applications including fat/trim lines, cutting lines, general conveyance and packaging lines- Fruit & vegetable applications including elevators, inspection tables and packaging lines- Seafood applications including inspection tables, grading lines and trim lines- Bakery applications including raw dough handling, cooling lines and packing lines
Product features and operational benefits:- Easy to clean Single Link® belt – reduces downtime for cleaning up to 70%- Single Link® belt (no brick lay) reduces bacteria growth- Single Link® eliminates knives sticking in belt seams- Unique locking system (lockpin) – faster, simpler maintenance- Unique sprocket engagement – higher product load and longer conveyors- Strong and thick Single Link® product supports eliminate gaps across the width where product can become trapped - Close transfer applications
Pitch 25.4 mm (1.00 in.)
New
33
uni S-MPB
ST
AN
DA
RD
uni S-MPB-C
Standard Selection
uni S-MPB-C
T
LE
P
Dimensional Sketch
Travel
L
T
E
5.2
10.4
5.1
mm
0.21
P 25.4 1.00
0.41
0.20
in.
Dimensions
25.4 mm (1.00 in.)
See page 7, 8 and 9
Straight running
See page 35
Materials
23 mm (0.91 in.)
TypeMaterials and colors
Standard Materials and Colors
uni S-MPB-C W
PP
PE-I PA6.6
POM-DI NPA6.6
N
N
PA6.6
Standard pinsStandard materials and colors
mm
76
152
228
304
380
456
532
608
684
759
3.0
6.0
9.0
12.0
15.0
18.0
20.9
23.9
26.9
29.9
mm
835
911
987
1063
1139
1215
1291
1367
1443
1519
32.9
35.9
38.8
41.8
44.8
47.8
50.8
53.8
56.8
59.8
1595
1671
1747
1823
1898
1974
2050
2126
2202
2278
62.8
65.8
68.8
71.8
74.7
77.7
80.7
83.7
86.7
89.7
mm
2354
2430
2506
2582
2658
2734
2810
2885
2961
3037
92.7
95.7
98.7
101.7
104.6
107.6
110.6
113.6
116.6
119.6
in. in. in. in. in.
Standard Bricklayed Belt Widths (See next page for Single Link® widths)
mm mm
Patent Patent pending
B
BN
W
See page 129
34
ST
AN
DA
RD
uni S-MPB
uni S-MPB Single Link®
uni S-MPB is also available as Single Link® in the following standard widths:
K600 (151.9 mm (5.98 in.))
K2000 (506.7 mm (19.95 in.))
K300 (75.9 mm (2.99 in.))
uni S-MPB Single Link®
N/m
23500
PA6.6
POM
lb/ft
1610
N/m
9500
PA6.6
PP
lb/ft
651
N/m
7850
PA6.6
PE
lb/ft
538
uni S-MPB Single Link®
kg/m2
8.3
POM
1.69
kg/m2
5.6
PP
1.14
kg/m2
5.7
PE
1.18
Pin material
Belt material
Permissible Tensile Strength
Pin material
Belt material
plastic
lb/ft2
plastic
lb/ft2
plastic
lb/ft2
Belt Weights
uni S-MPB Product Support
Height
mm in.Style
Width Indent both sides Standard materials & colors
POM-DI
50.8 2.00 Indent
Type in.mm in.
506.7 19.95
mm in.
25.8 1.02K2000 W
PP
uni S-MPB Product Support
Dimensional Sketch
Travel
Standard Materials, Colors and Dimensions
Standard Selection Accessories
BW
PE-I
BN
35
uni S-MPB
ST
AN
DA
RD
Belt material POM
N lb N lb
uni S-MPB 1100 247 500 112
PP
N lb
500 112
PE
Standard Bi-directional Sprockets
1.3033.01.9248.82.0050.86 7833SMPB06NR2
in.in. mmmmin.mmin.mm
Hub diameterOverall diameterPitch diameterNo. ofteeth
ø0.63/1.00*ø16.0/25.4*
1.9750.02.5865.62.6166.48 7833SMPB08NR2ø0.63/1.57*ø16.0/40.0*
2.6066.03.2482.23.2482.210 7833SMPB10NR2ø0.71/1.57*ø18.0/40.0*
2.7670.03.8898.63.8698.112 7833SMPB12NR2ø0.71/1.57*ø18.0/40.0*
2.7670.04.85123.14.81122.215
7833SMPB15NR2ø0.71/1.57*ø18.0/40.0*
7833SMPB15NR215INSQsq 1.50sq 38.1
7833SMPB15NR240MMSQsq 1.57sq 40.0
Reference no. plastic
Bore
2.7670.06.45163.86.39162.420 7833SMPB20NR2ø0.71/1.57*ø18.0/40.0*
Width of sprockets: 25.0 mm (0.98 in.)Tooth width: 12.7 mm (0.50 in.)
uni S-MPB sprocket
PA6 N
Other sprocket sizes are available upon request. Two-part sprockets available upon request.
Please contact uni-chains® for further information.
* Minimum/maximum round bore.
Standard Material and Color
Max. Load per Sprocket
No. of
teethmm in. mm in.
6
8
10
12
16.9
25.6
30.8
38.5
46.4
54.4
1.21
1.52
1.83
2.14
34.0
42.3
0.67
1.01
1.34
1.67
15 66.4 2.61 54.6 2.15
20 86.5 3.41 75.1 2.96
Minimum B-dimension
Wearstrip distance A
A
B
Placement of Wearstrips and Sprockets
36
ST
AN
DA
RD
uni QNB
uni QNB – strong and reliableThe uni QNB is a belt developed for different applications in many industries. The belt is unique due to its strength andreliability. The chamfered edges allow easy side transfer and eliminate catch points.
The uni QNB belt has increased performance in the following industries/applications:- Bakery applications including pan handling and incline/decline box or pan applications- Meat and poultry applications including packaging lines and incline box conveyors- Beverage applications including depalletizers, accumulation tables and incline case conveyors- Can manufacturing applications including palletizers, mass handling and accumulation tables- Corrugated applications including downstacker, corrugator take off, transfer car and WIP storage- Tire applications including wigwag, extruder takeaway and Inspection applications- Material handling applications including Incline applications, palletizers and packaging lines
Product features and operational benefits:- Strong, bi-directional belt for long conveyors- Rough Top non-slip surface for increased worker safety- Unique locking system (lockpin) for easy maintenance- Unique sprocket engagement reduces pulsation and increases load capacity- Unique Rubber Top eliminates wear and increases friction properties on incline/decline applications
Pitch 25.4 mm (1.00 in.)
37
uni QNB
ST
AN
DA
RD
25.4 mm (1.00 in.)
See page 7 and 8
Straight running
See page 39
Materials
40 mm (1.6 in.)
K03
NPA6.6
DPA6.6
DPP
W WPP PE
SS304BPA6.6
Accessories
See page 40
See page 11
uni QNB C uni QNB Rough uni QNB Rubber Top*
Standard Selection
uni QNB C
Dimensional Sketches
uni QNB Rough
E
B
5.1
4.5
mm
0.20
0.18
in.
L
F
4.4
0.8
mm
0.17
0.03
in
T
P
8.8
25.4
mm
0.35
1.00
in.
Dimensions
E
Travel Travel
E
F
P
L L
P
uni QNB Rubber Top
Travel
E
B
L
P
T T T
Alternatives
TypeStandard materials
and colors
Standard pins
Materials and colors
Standard Materials and Colors
uni QNB C
uni QNB Rough
uni QNB Rubber Top
GPP
DPA6.6
B
BPOM-SLF
DPA6.6
DPA6.6
DPA6.6
GPP
BPOM-SLF
+
mm
76
152
228
304
379
455
531
607
683
759
3.0
6.0
9.0
12.0
38
51
1.5
2.0
14.9
17.9
20.9
23.9
26.9
29.9
mm
835
911
987
1063
1139
1214
1290
1366
1442
1518
32.9
35.9
38.8
41.8
44.8
47.8
50.8
53.8
56.8
59.8
mm
1594
1670
1746
1822
1898
1973
2049
2125
62.8
65.7
68.7
71.7
74.7
77.7
80.7
83.7
mm mmin. in. in. in. in. mm in. mm in.
Standard Bricklayed Belt Widths (See next page for Single Link® widths)
K03
* Dimensional sketches for Rubber Top see page 40.
Patent Patent pending
2201
2277
86.7
89.6
2353
2429
2505
2581
2657
2732
2808
2884
2960
3036
92.6
95.6
98.6
101.6
104.6
107.6
110.6
113.6
116.5
119.5
See page 129
38
ST
AN
DA
RD
uni QNB
Belt type and widthsK150
37.8 mm (1.49 in.)
Standard Single Link® Belt Widths
K200 50.5 mm (1.99 in.)
K300 75.8 mm (2.98 in.)
K600 152.0 mm (5.98 in.)
uni QNB C X X
X X
X X
uni QNB Rough
uni QNB Rubber Top
uni QNB Single Link®
uni QNB is available as Single Link® in the followingstandard widths:
K300 (75.8 mm (2.98 in.))
K600 (152.0 mm (5.98 in.))
K150 (37.8 mm (1.49 in.))
K200 (50.5 mm (1.99 in.))
239835000
N/m
POM
137020000
N/m
PP
-- 137020000
Permissible Tensile Strength
uni QNB C/uni QNB Rough
lb/ft lb/ft
uni QNB Rubber Top
Belt material
PA6.6 and PP PA6.6 and PPPin material
1.708.3
kg/m2
PP
POM
1.095.3
--
1.728.4
kg/m2
PA6.6
-- 1.416.9
kg/m2
PP
PP
1.115.4
--
kg/m2
PA6.6
Belt Weights
uni QNB C/uni QNB Rough
lb/ft2
Pin material
lb/ft2
uni QNB Rubber Top
lb/ft2 lb/ft2
Belt material
SLO SLO
SLO = Single Link only
39
uni QNB
Standard Sprockets
2.5665.03.1680.33.2482.210
1433QNB10N
1433QNB0N15INSQ
in.in. mmmmin.mmin.mm
Hub diameterOverall diameterPitch diameterNo. ofteeth
ø0.71/1.57*ø18.0/40.0*
sq 1.50sq 38.1
1433QNB10N40MMSQsq 1.57sq 40.0
2.7670.03.8196.83.8698.112
1433QNB12N
1433QNB12N15INSQ
1433QNB12N40MMSQ
ø0.71/1.57*ø18.0/40.0*
sq 1.50sq 38.1
sq 1.57sq 40.0
2.7670.0
3.94100.0
4.78121.54.81122.215
1433QNB15N
1433QNB15N15INSQ
1433QNB15N40MMSQ
1433QNB15NBB
1433QNB15NBB25INSQ
ø0.71/1.57*ø18.0/40.0*
sq 1.50sq 38.1
sq 1.57sq 40.0
ø1.57/2.76*ø40.0/ø70*
sq 2.50sq 63.5
1433QNB15NBB60MMSQsq 2.36sq 60.0
2.7670.0
4.72120.0
4.09104.0
5.75146.15.76146.318
1433QNB18N
1433QNB18N15INSQ
1433QNB18N40MMSQ
1433QNB18NBB
ø0.71/1.57*ø18.0/40.0*
sq 1.50sq 38.1
sq 1.57sq 40.0
ø1.57/2.76*ø40.0/ø70*
1433QNB18NBB60MMSQsq 2.36sq 60.0
Reference no. plastic
Bore
2.7670.0
4.72120.0
6.07154.26.07154.319
1433QNB19N
1433QNB19N15INSQ
1433QNB19N40MMSQ
1433QNB19NBB
ø0.71/1.57*ø18.0/40.0*
sq 1.50sq 38.1
sq 1.57sq 40.0
ø1.57/2.76*ø40.0/ø70*
1433QNB19NBB60MMSQsq 2.36sq 60.0
Belt material POM
N lb N lb
uni QNB 2300 517 1300 292
PP
Width of sprockets: 25.0 mm (0.98 in.)Tooth width: 10.0 mm (0.39 in.)
uni QNB sprocket
PA6 N
Other sprocket sizes are available upon request. Two-part sprockets available upon request.Please contact uni-chains® for further information.
Max. Load per Sprocket
ST
AN
DA
RD
* Minimum/maximum round bore.
Standard Material and Color
No. of
teethmm in. mm in.
10
12
15
18
34.7
43.0
45.5
53.5
65.5
77.5
1.79
2.11
2.58
3.05
55.3
67.6
1.37
1.69
2.18
2.66
19 81.6 3.21 71.7 2.82
Minimum B-dimension
Wearstrip distance A
A
B
Placement of Wearstrips and Sprockets
4.09104.0
40
uni QNB
uni QNB Product Support
uni QNB Product Support
Dimensional Sketch
Travel
Height
mm in.
Width Standard materials & colors
POM-SLF PP-I
25.4 1.00
Type mm in.
152.0 5.98K600 B G
ST
AN
DA
RD
Standard Materials, Colors and Dimensions
Standard Selection Accessories
Dimensional Sketches for Rubber Top
A
AB
AC
A 7.3 0.29
B 14.9 0.58
C 83.5 3.29
mm in.
Dimensions
Minimum bricklaid indent is for uni QNB product support 25.4 mm (1.00 in.).Increment: 25.4 mm (1.00 in.).
41
uni CNB
uni CNB – cleanable belt for light duty applicationsThe uni CNB belt is a cleanable belt for conveying of light duty products in various food applications. The belt is availablewith different openings to optimize drainage and airflow and includes accessories such as product supports and sideguards. The unique hinge and sprocket design make the belt very easy to clean.
The uni CNB belt is the preferred belt in the following industries/applications:- Meat & poultry applications including general conveyance and breading lines- Fruit & vegetable applications including elevators, steam peeler and inspection tables- Seafood applications including elevators, inspection tables, grading lines, trim lines, glazing lines and cooking lines- Bakery applications including raw dough handling, cooling lines, icing lines, packing lines and metal detectors
Product features and operational benefits:- Easy to clean - Unique locking system (lockpin) – faster, simpler maintenance- Unique sprocket engagement – precise indexing, easy cleaning- Different openings to optimize performance in cooling and draining applications
Pitch 25.4 mm (1.00 in.)
ST
AN
DA
RD
42
uni CNB C uni CNB 18% uni CNB 22%
Standard Selection
W WPP PE
BPA6.6 SS304
25.4 mm (1.00 in.)
See page 7, 8 and 9
Straight running
See page 44
Materials
40 mm (1.6 in.)
See page 45
See page 45
Accessories
Alternatives
TypeStandard materials
and colors Materials and colors
Standard Materials and Colors
uni CNB C W
WPP
BPP PA6.6
POM-D
NPE NPA6.6
uni CNB 18% WPP PA6.6
NPA6.6
N
N
PA6.6
N
uni CNB 22% WPP PA6.6 N
WPOM-D PA6.6 N
PE PA6.6 N
Standard pins
uni CNB
mm
76
152
228
304
379
455
531
607
683
759
3.0
6.0
9.0
12.0
14.9
17.9
20.9
23.9
26.9
29.9
mm mm
835
911
987
1063
1139
1214
1290
1366
1442
1518
32.9
35.9
38.8
41.8
44.8
47.8
50.8
53.8
56.8
59.8
mm
1594
1670
1746
1822
1898
1973
2049
2125
2201
2277
62.8
65.7
68.7
71.7
74.7
77.7
80.7
83.7
86.7
89.6
mm
2353
2429
2505
2581
2657
2732
2808
2884
2960
3036
92.6
95.6
98.6
101.6
104.6
107.6
110.6
113.6
116.5
119.5
in. in. in. in.
Standard Bricklayed Belt Widths (See next page for Single Link® widths)
uni CNB
TL
E
P
R
Dimensional Sketch
Travel
L
R
E
4.4
3.0
5.1
mm
0.17
P 25.4 1.00
0.12
T 8.8 0.35
0.20
in.
Dimensions
ST
AN
DA
RD
in.
Patent Patented
See page 129
N
43
uni CNB
ST
AN
DA
RDuni CNB Single Link®
uni CNB is available as Single Link® in the followingstandard widths:
K300 (75.9 mm (2.99 in.))
K600 (152.0 mm (5.98 in.))
92513500uni CNB C, 18%, 22%
N/m
107615700
N/m
5147500
N/m
PP
Permisible Tensile Strength
lb/ft
plasticPin material
lb/ft
steel
lb/ft
plastic
5147500
N/m lb/ft
steel
4256200
N/m
PE
lb/ft
plastic
3975800
N/m lb/ft
steel
Belt material POM
1.195.8uni CNB C
kg/m2
1.025.0uni CNB 18%
0.984.8
0.803.9
kg/m2
0.723.5
0.703.4
0.824.0
kg/m2
PE
0.743.6
0.723.5uni CNB 22%
Belt Weights
lb/ft2
plasticPin material
lb/ft2
plastic
lb/ft2
plastic
Belt material PPPOM
44
uni CNB
Standard Sprockets
2.5665.03.1780.63.2482.210
1933CNB10N
1933CNB10N15INSQ
in.in. mmmmin.mmin.mm
Hub diameterOverall diameterPitch diameterNo. ofteeth
ø0.71/1.57*ø18.0/40.0*
sq 1.50sq 38.1
1933CNB10N40MMSQsq 1.57sq 40.0
2.7670.03.8196.83.8698.112
1933CNB12N
1933CNB12N15INSQ
1933CNB12N40MMSQ
ø0.71/1.57*ø18.0/40.0*
sq 1.50sq 38.1
sq 1.57sq 40.0
2.7670.04.78121.54.81122.215
1933CNB15N
1933CNB15N15INSQ
ø0.71/1.57*ø18.0/40.0*
sq 1.50sq 38.1
1933CNB15N40MMSQsq 1.57sq 40.0
2.7670.04.72146.15.76146.318
1933CNB18N
1933CNB18N15INSQ
ø0.71/1.57*ø18.0/40.0*
sq 1.50sq 38.1
1933CNB18N40MMSQsq 1.57sq 40.0
2.7670.06.07154.26.07154.319
1933CNB19N
1933CNB19N15INSQ
ø0.71/1.57*ø18.0/40.0*
sq 1.50sq 38.1
1933CNB19N40MMSQsq 1.57sq 40.0
Reference no. plastic
Bore
Belt material POM
N lb N lb
uni CNB 600 135 500 112
PP
Width of sprockets: 25.0 mm (0.98 in.)Tooth width: 12.0 mm (0.47 in.)
uni CNB sprocket
PA6 N
Standard Material and Color
Max. Load per Sprocket
Other sprocket sizes are available upon request. Two-part sprockets available upon request.
Please contact uni-chains® for further information.
* Minimum/maximum round bore.
No. of
teethmm in. mm in.
10
12
15
18
34.7
43.0
45.5
53.5
65.5
77.5
1.79
2.11
2.58
3.05
55.3
67.6
1.37
1.69
2.18
2.66
19 81.6 3.21 71.7 2.82
Minimum B-dimension
Wearstrip distance A
A
B
Placement of Wearstrips and Sprockets
ST
AN
DA
RD
45
uni CNB
ST
AN
DA
RD
uni CNB Side Guard
Dimensional SketchTravel
P
AB
C
PP-I
B
A
50.8
25.4
mm
2.00
C 76.2 3.00
P 25.4 1.00
1.00
in.
Dimensions
W
uni CNB Product Support (No Indent) uni CNB Micro Product Support 22%
* uni CNB Micro Product Support 22%: Standard indent in both sides is 6.4 mm (0.25 in).** Minimum bricklaid indent for uni CNB product support is 38.1 mm (1.50 in.).Increment: 12.7 mm (0.50 in.).
Height
mm in.Style
Width
152.0 5.98K600
Moldedindent
Standard materials & colors
POM-D PE PP-I
1.00 No indent25.4
5.0 0.2022% micro
Wno**
Type mm in.
N WB
152.0 5.98K6002.00 No indent50.8 Wno** N WB
152.0 5.98K6003.00 No indent76.2 no**
75.9 2.99K300 LI/RI*
152.0 5.98K600 LI/RI*
N WB
W
WN
N
uni Product Support
Dimensional Sketch
Travel
Standard Materials, Colors and Dimensions
Standard Materials
Standard Selection Accessories
Standard Selection Accessories
Min indent to outside of side guards:14.0 mm (0.55 in.).Increment: 6.4 mm (0.25 in.).
46
ST
AN
DA
RD
uni Flex SNB – strong and tight radius side flexing beltuni Flex SNB 1 in. pitch was created to optimize throughput in high volume operations with space limitations. The belthas unique strength and side flexing characteristics and is used in many different applications.
The uni Flex SNB belt has increased performance in the following industries/applications:- Meat & poultry applications including tray pack conveyors, box/tote handling, freezers infeed/outfeed, low tension
spirals and other side flexing applications- Fruit & vegetable applications including filling lines, canning lines and incline/decline applications- Bakery applications including cooling lines, pan handling, proofers and oven infeed and takeaway- Beverage applications including case conveyors, shrink tunnels and incline/decline applications- Can manufacturing applications including mass handling, transfer conveyors and palletizers infeed conveyors.
Product features and operational benefits:- 180 degree high speed side flexing applications- High temperature and wear resistance- Tight radius applications – reduced space requirements- Unique locking system (no pin walking or pins coming out)- Unique radius top surface for minimum product contact and less friction- Reinforced stainless steel links for higher strength, speed or load
Pitch 25.4 mm (1.00 in.)
uni Flex SNB
48
25.4 mm (1.00 in.)
Side flexing
See page 54
50 mm (2.0 in.)
See page 7, 8 and 10Materials
K03
WPP
SS304 SS316
N03
See page 11Indent: uni Flex SNB-CR RubberTop is 26.5 mm (1.04 in.) uni Flex SNB-C RubberTop is 7.0 mm (0.28 in.).uni Flex SNB-L Rubber isavailable without indent.
uni Flex SNB
ST
AN
DA
RD
uni Flex SNB-L uni Flex SNB-CRuni Flex SNB-C
uni Flex SNB-W uni Flex SNB-WT
uni Flex SNB-CRRubber Top
uni Flex SNB-CRubber Top
uni Flex SNB-WO
Standard Selection
uni Flex SNB-C/CRuni Flex SNB-L/W/WO uni Flex SNB-WT
Dimensional Sketches
Travel
TE L
Travel
P P
E L LT
Travel
P
E T
A
Alternative
Surface opening 55% Surface opening 47% Surface opening 47%
Surface opening 55% Surface opening 55%
Surface opening 47% Surface opening 47%
Surface opening 55%
uni Flex SNB-L: Standard radius. Min. inside radius 2.3 x belt width, 55% open area for max. airflow/cooling.
uni Flex SNB-C: Standard radius. Min. inside radius 2.3 x belt width. 47% open hygienic solid grid surface.
uni Flex SNB-CR: Tight radius. Min. inside radius 1.6 x belt width. 47% open hygienic solid grid surface.
uni Flex SNB-W: Standard radius (2.3 x W) fitted with reinforcement links and steel pins. Integral molded edge wearpart.
uni Flex SNB-WT: Standard radius (2.3 x W) fitted with cover links and PA6.6 pins or with reinforcement links and steel pins. Integral molded edgewearpart. Integral underside tab (S-Tab).
uni Flex SNB-WO: Standard radius (2.3 x W) fitted with reinforcement links and steel pins. Integral outer edge tab system. Transports products widerthan the belt.
uni Flex SNB Rubber Top
Travel
P
E
R
L T
E
A
5.1
12.0
mm
0.20
0.48
in.
P
L
25.4
6.5
mm
1.00
0.26
in
T
R
13.0
3.0
mm
0.51
0.12
in.
Dimensions
Patent Patented
See page 129
49
TypeStandard materials
and colors
Standard pins
Materials and colors
Standard Materials and Colors
uni Flex SNB-L
uni Flex SNB-C/CR
W
W
POM-D
BPOM-D
PP
BPP
NPA6.6
NPA6.6
NPA6.6
NPA6.6
BPA6.6
BPA6.6
BPA6.6 BPA6.6
PA6.6 NPA6.6
BPA6.6
WPP
BPP
WPOM-D
BPOM-D
BPA6.6
uni Flex SNB-W SS304
uni Flex SNB-WT SS304 or NPA6.6
or BPA6.6
SS304
SS304
SS304
SS304
SS304
SS304
orSS304
or BPA6.6SS304
or BPA6.6SS304
SS304
SS304
SS304
SS304
SS304
SS304S
TA
ND
AR
D
W
BPA6.6 BPA6.6
PA6.6 NPA6.6W
uni Flex-SNB Rubber Top B BPA6.6
NPA6.6
uni Flex SNB
K03+
+
PP
WPP N03
For uni Flex SNB-W/WT/WO: Outer modules are always in PA6.6. On belt widths wider than 235 mm (9 in.) beltmay be combined with any of above L or CM links in the middle.Reinforcement links:
For all uni Flex SNB-L: Lockingplate/Wearparts/O-TabLockingplates: BW
Wearparts and O-Tabs: BW
O
SS304
Cover links: BW
PP
PA6.6
PA6.6
W
W
POM-D
BPOM-D
PP
BPP
BPA6.6
PA6.6 W
W
W
POM-D
BPOM-D
PP
BPP
BPA6.6
PA6.6 W
uni Flex SNB-WO W
W
POM-D
BPOM-D
PP
BPP
BPA6.6
PA6.6 W
NPA6.6
orSS304 NPA6.6
For high speed and/or abrasive applications offers: uni Flex SNB cover link
Wearpart and O-Tab in POM-DK:
50
uni Flex SNB Single Link®
uni Flex SNB is also available as Single Link® in the following standard widths:
See below for specific belt types available in each width.
K300 (75.9 mm (2.99 in.))
K600 (152.1 mm (5.99 in.))
K1200 304.5 mm (11.99 in.)
Belt type and widths
Standard Single Link® Belt Widths
uni Flex SNB-L
uni Flex SNB-C
K1200304.5 mm (11.99 in.)
X
K600 152.1 mm (5.99 in.)
X
K300 75.9 mm (2.99 in.)
X
XX
uni Flex SNB-CR XX
uni Flex SNB-W*
uni Flex SNB-WT*
uni Flex SNB-WO*
XX
X
XX
mm
76*
152*
228
304
379
456
532
3.0*
5.9*
9.0
12.0
14.9
18.0
20.9
mm
608
684
760
23.9
26.9
29.9
836
912
988
1065
32.9
35.9
38.9
41.9
- -
- -
Non standard cut widths are possible in multiples of 12.7 mm (0.50 in.).To find the belt widths for other uni Flex SNB tracking systems and belt typesuse formulas to the right.
* Note: These belt widths are only available for uni Flex SNB-L and uni Flex SNB-C.
Standard Modular Belt Widths for uni Flex SNB-L (WL)in. in. mm in. mm in.
uni Flex SNB-C/CR: W = WL
uni Flex SNB-L or C/CR with wearpart both sides: W = WL + 2 x 3 mm (0.24 in.)
For wearpart /O-Tab one side:1 x 3 mm (0.12 in.)
uni Flex SNB-L, C/CR with O-Tab both sides: W = WL + 2 x 3 mm (0.24 in.)
For wearpart /O-Tab one side:1 x 3 mm (0.12 in.)
uni Flex SNB-W, WO or WTboth sides: W = WL + 2 x 3 mm (0.24 in)
uni Flex SNB
ST
AN
DA
RD
* Note: Integrated wearpart, integrated underside tab (S-Tab) and integrated outer edge tab system.
51
uni Flex SNB-L/C/CR
uni Flex SNB-L/C/CR
PP or SS
PA6.6
Pin material
Belt material
600
600
N
135
135
lb
PP
Max. Permissible Load in Curve
uni Flex SNB-W/WO/WT
uni Flex SNB-W/WO/WT
PP or SS
PA6.6
Pin material
Belt material
600
1000
N
135
225
lb
POM/PA6.6
600
600
N
135
135
lb
PP
uni Flex SNB-W/WO/WT SS + RL* 3300 742 - -
* RL = Reinforcement link
uni Flex SNB-L, C, CR, W, WO, WT 30000
N/m
2055
lb/ft
POM/PA6.6
15000
N/m
1028
lb/ft
PPBelt material
Max. Permissible Load on Straight Sections
Belt type Material Hinge design Flex ratio
uni Flex SNB-L all plastic open hinge 2.3
uni Flex SNB-C all plastic closed hinge 2.3*
uni Flex SNB-CR all plastic closed hinge 1.6
uni Flex SNB-W plastic and steel open hinge 2.3
uni Flex SNB-WT all plastic or plastic and steel open hinge 2.3
uni Flex SNB-WO plastic and steel open hinge 2.3
uni Flex SNB Program
Refer to this diagram for the material combinations, surface openings and turning radii of the five different uni Flex SNBtypes.
Inner curve radius = Flex ratio x belt width.
* K300 Single Link® Flex ratio = 1.8 and K600 Single Link® Flex ratio = 1.7.
ST
AN
DA
RD
uni Flex SNB
Max. Permissible Load in Curve
600
1000
N
135
225
lb
POM/PA6.6
7423300uni Flex SNB
N/pcs
Load Capacity per Reinforcement Linklb/pcs
The use of uni-chains® belt with the SS reinforcement /Pitch control links in blanchers, cookers and other high temperatu-re applications will reduce belt elongation due to temperature by more than 90%. This will simplify the belt take-upsystem and reduce maintenance.
52
Basic belt types can be combinedwith the belt tracking and controlsystems below to enhance per-formance.
Belt width (WL)
Wearpart system made of heat andwear resistant nylon to reduce thefriction between belt edge andwearstrip. Only this part needs tobe replaced when it has been wornout, not the whole belt.
Belt width (W)
W - 6 mm (0.24 in.)
Outer edge tab system made ofheat and wear resistant nylon toreduce the friction between beltedge and wearstrip. Using a slot-ted wearstrip the O-Tab will trackthe belt and allow the transportedproducts to be wider than the belt.
W + 12 mm (0.5 in.)
Belt width (W)W - 6 mm (0.24 in.)
Intermediate tabs are placed on thebottom side of the belt to hold thebelt down on incline conveyors.The intermediate tabs will fit any-where across the belt bottom andat pitch multiples of 12.7 mm(0.50 in.).
Side tab for holding the belt down,normally used for wide belts. WithS-Tabs the radial forces in the cur-ve are transferred to the outsideradius (uni Flex SNB-WT).
R = 34.0 mm (1.34 in.).
Belt width (W)
W - 68 mm (2.68 in.)
Reinforcement link
Belt typeWearpart
uni Flex SNB-L +
uni Flex SNB-C/CR +
uni Flex SNB-W ✔✔
uni Flex SNB-WT -
uni Flex SNB-WO -
O-Tab
+
+
-
-
✔✔
S-Tab
-
-
-
✔✔
-
I-Tab
+
-
+
+
+
Standard Optional Not possible✔✔ -+
Belt tracking and control combination
uni Flex SNB-L(Standard)
Wearpart
O-Tab
I-Tab
S-Tab
R R
uni Flex SNB
ST
AN
DA
RD
Please note that the tabs are not always placed in the middle ofthe belt.
Note: When using S-Tabs please verify that sufficient clearance to the shaft exists. Max. shaft diameter = Sprocket pitch diameter - 50.8 mm (2.00in.). When using square shafts verify that the diagonal does not exceed above max. diameter. Example: Sprocket z = 10: Max. shaft diameter 82.2 - 50.8 = ø31 mm (3.24 - 2.00 = ø1.2 in.).
Belt Tracking and Control Systems
53
PA6.6
SS
PP
kg/m2
6.7
POM PP
1.37
kg/m2
4.6 0.94
6.9 1.41 4.8 0.98
12.1 2.48 10.0 2.05
Belt Weights for uni Flex SNB-L
Pin material
Belt material
lb/ft2 lb/ft2 kg/m2
5.6
PA6.6
1.15
5.8 1.19
11.0 2.25
lb/ft2
PA6.6
SS
PP
kg/m2
7.5
POM PP
1.54
kg/m2
5.2 0.94
7.7 1.58 5.4 0.98
12.9 2.64 10.2 2.09
Belt Weights for uni Flex SNB-C/CR
Pin material
Belt material
lb/ft2 lb/ft2 kg/m2
6.2
PA6.6
1.27
6.4 1.31
11.6 2.38
lb/ft2
PA6.6
SS
PP
kg/m2
7.1
POM PP
1.45
kg/m2
4.9 1.00
7.3 1.50 5.1 1.04
12.5 2.56 10.3 2.11
Belt Weights for uni Flex SNB-W
Pin material
Belt material
lb/ft2 lb/ft2 kg/m2
5.8
PA6.6
1.19
6.0 1.23
11.2 2.29
lb/ft2
PA6.6
SS
PP
kg/m2
7.3
POM PP
1.52
kg/m2
5.1 1.04
7.5 1.54 5.3 1.09
12.7 2.60 10.5 2.15
Belt Weights for uni Flex SNB-WO
Pin material
Belt material
lb/ft2 lb/ft2 kg/m2
6.1
PA6.6
1.25
6.2 1.27
11.4 2.34
lb/ft2
PA6.6
SS
PP
kg/m2
7.4
POM PP
1.52
kg/m2
5.1 1.04
7.6 1.56 5.3 1.09
12.8 2.62 10.5 2.15
Belt Weights for uni Flex SNB-WT
Pin material
Belt material
lb/ft2 lb/ft2 kg/m2
6.1
PA6.6
1.25
6.3 1.29
11.5 2.36
lb/ft2
ST
AN
DA
RD
uni Flex SNB
54
Standard Sprockets
2.2456.82.9173.82.9374.39
2133FSNB09N
2133FSNB0910INSQ
2133FSNB0930MMSQ
in.in. mmmmin.mmin.mm
Hub diameterOverall diameterPitch diameterNo. ofteeth
ø0.71/1.18*ø18.0/30.0*
sq 1.00sq 25.4
sq 1.18sq 30.0
2.5765.23.2482.23.2482.210
2133FSNB10N
2133FSNB10N10INSQ
ø0.71/1.57*ø18.0/40.0*
sq 1.00sq 25.4
2133FSNB10N30MMSQsq 1.18sq 30.0
2.7670.03.8998.83.8798.212
2133FSNB12N
2133FSNB12N15INSQ
2133FSNB12N40MMSQ
ø0.71/1.57*ø18.0/40.0*
sq 1.50sq 38.1
sq 1.57sq 40.0
Bore
2.7670.04.86123.54.81122.215
2133FSNB15N
2133FSNB15N15INSQ
ø0.71/1.57*ø18.0/40.0*
sq 1.50sq 38.1
2133FSNB15N40MMSQsq 1.57sq 40.0
2.7670.05.75146.15.76146.318
2133FSNB18N
2133FSNB18N15INSQ
ø0.71/1.57*ø18.0/40.0*
sq 1.50sq 38.1
2133FSNB18N40MMSQsq 1.57sq 40.0
2.7670.06.15156.26.07154.319
2133FSNB19N
2133FSNB19N15INSQ
ø0.71/1.57*ø18.0/40.0*
sq 1.50sq 38.1
2133FSNB19N40MMSQsq 1.57sq 40.0
Reference no. plastic
Width of sprockets: 25.0 mm (0.98 in.)Tooth width: 6.4 mm (0.25 in.)
uni Flex SNB sprocket
PA6 N
Other sprocket sizes are available upon request. Two-part sprockets available upon request.
Please contact uni-chains® for further information.
* Minimum/maximum round bore.
Standard Material and Color
No. of
teethmm in. mm in.
9
10
12
15
28.4
32.6
43.5
47.5
55.5
67.5
1.71
1.87
2.19
2.66
40.9
53.2
1.12
1.28
1.61
2.09
18 79.6 3.13 65.5 2.58
19 83.6 3.29 69.6 2.74
Minimum B-dimension
Wearstrip distance A
A
B
Placement of Wearstrips and Sprockets
uni Flex SNB
ST
AN
DA
RD
55
Product Support 50.8 mm (2.0 in.)
Product Support 25.4 mm (1.0 in.)
Rubber Support Made-To-Order see page 115
Product Support low Made-To-Order see page 115
Side Guard
Rubber Top
•
•• •
•
•
Belt type Rubber Top
uni Flex SNB-L +
uni Flex SNB-C +1/
uni Flex SNB-W +3/
uni Flex SNB-WT +3/
uni Flex SNB-WO +3/
Side guard
+
-
+
+
+
Product support
+
-
uni Flex SNB-CR +2/ - -
+
+
+
1/ Minimum indent from the side of the belt 6.5 mm (0.26 in.). 2/ Minimum indent from the side of the belt 26.5 mm (1.04 in.). 3/ Minimum indent from the side of the belt 75.9 mm (2.99 in.).
For build patterns please contact uni-chains®.
+ = Optional - = Not possible
Height
mm in.
StyleWidth
Standard materials & colors
PA6.6 PP-I PPmm in.
B75.91.00 Product
support
25.4
2.0050.82.99
B-1.18Sideguard
30.0 -
B
Standard Materials and Colors
Belt Top Accessories
ST
AN
DA
RD
uni Flex SNB
56
uni SNB M2 – the unique open top and rib top beltThe new uni SNB M2 20% (Closed hinges) offers improved cleanability while still maintaining high strength properties.The flat surface of the uni SNB M2 20% allows for gentle transport of sensitive products while still providing an open surface for airflow or drainage. The uni SNB M2 belt may be used with uni SNB M2 Single Link® mold-to-width chains in de-combiners or combiners toincrease conveyor speed and product throughput. The open radius top surface makes the belt unique especially in dryapplications.
The uni SNB M2 belt increases performance in the following industries/applications:- Meat applications including microwaves, cooling and freezing lines- Fruit & vegetable applications including de-watering lines, cooling and freezing lines- Pasta applications including blanchers, pasteurizers and cooling lines- Beverage applications including accumulating tables, infeed to packaging, pasteurizers and palletizers- Can manufacturing applications including accumulation tables, mass handling and palletizers
Product features and operational benefits:- Less friction and product contact – for easy cooking, cooling and freezing of products- Radius top surface reduces back line pressure with up to 70%- Reduced dirt and oxide build up due to self cleaning surface- Unique locking system (lockpin) – easy assembly and less downtime - Finger plates for trouble free transfer
Pitch 25.4 mm (1.00 in.)
uni SNB M2
ST
AN
DA
RD
57
ST
AN
DA
RD
uni SNB M2
uni SNB M2 34% uni SNB M2 20%uni SNB M2 34% Rib
Standard Selection
GWBPP
W WPP PE
BPA6.6 SS304
N See page 11
25.4 mm (1.00 in.)
See page 7, 8 and 9
Straight running
See page 61
Materials
30 mm (1.2 in.)
See page 59
Accessories
See page 60
TypeStandard materials
and colors
Standard pins
Materials and colors
D
D
PA6.6
PA6.6
NPA6.6
NPA6.6
DPA6.6
Standard Materials and Colors
uni SNB M2 34% and uni SNB M2 20%
uni SNB M2 34% Rib
B
W
POM-D
PP
PP
BPOM-SLF
NPE
PP
uni SNB M2 20% Rubber Top K03+
AlternativeOnly for uni SNB M2 34% anduni SNB M2 34% Rib. Not 20%-style belts.
uni SNB M2 34% and M2 20%
Dimensional Sketches
uni SNB M2 34% Rib
E
Travel Travel
E
R
P
L L
P
T T
uni SNB M2 34% TAB and 20%TAB
Travel
E
Z
L
V
P
uni SNB M2 20% Rubber Top
Travel
E
SL
P
TT
L
P
E
4.4
25.4
5.1
0.17
1.00
T 8.8 0.35
R 5.5 0.22
S 3.4 0.13
0.20
mm in.
V 7.5 0.29
Z 15.0 0.59
Dimensions
GBPP
NPA6.6N03+WPP
uni SNB M2 20% Rubber Top
G
K03
Patent Patented
D
D
PA6.6
PA6.6
GB
See page 129
58
uni SNB M2
ST
AN
DA
RD
76
152
228
304
379
456
532
608
684
760
3.0
6.0
9.0
12.0
14.9
18.0
20.9
23.9
26.9
29.9
836
912
988
1064
1140
1216
1292
1368
1444
1520
32.9
35.9
38.9
41.9
44.9
47.9
50.9
53.9
56.8
59.8
1596
1672
1748
1824
1900
1976
2052
2128
2204
2280
62.8
65.8
68.8
71.8
74.8
77.8
80.8
83.8
86.8
89.8
2356
2432
2508
2584
2660
2736
2812
2888
2964
3040
92.8
95.7
98.7
101.7
104.7
107.7
110.7
113.7
116.7
119.7
mm in. mm in. mm in. mm in.
Standard Bricklayed Belt Widths (See below for Single Link® widths)
uni SNB M2 Single Link®
X
Belt type and widths K300
uni SNB M2 Single Link® Belt Widths
uni SNB M2 34%
uni SNB M2 34% TAB
uni SNB M2 34% Rib X
K450
X
K600
X
K750
X
K1200
uni SNB M2 20% X X
uni SNB M2 20% TAB Rubber Top
K325 K335
K300 (75.9 mm (2.99 in.))
K450 (114.3 mm (4.50 in.))
K600 (152.1 mm (5.99 in.))
K325 (82.3 mm (3.24 in.))
K335 (85.0 mm (3.35 in.))
K750 (189.4 mm (7.46 in.))
K1200 (304.5 mm (11.99 in.))
SLO SLO SLO SLO
uni SNB M2 20% TAB SLO
uni SNB M2 20% Rubber Top X1/ X1/ SLO2/
SLO2/
uni SNB M2 is also available as Single Link® in the following standard widths:
uni SNB M2 20% and 20% TAB Single Link®
uni SNB M2 34% TABSingle Link®
uni SNB M2 20% Rubber TopSingle Link®
SLO = Single Link® only 1/ Indent: 7.5 mm (0.30 in.) 2/ Indent: 36.4 mm (1.43 in.).
SLO
TypeStandard materials
and colors
Standard pins
Materials and colors
DPA6.6
Standard Materials and Colors
uni SNB M2 20% and 20% TAB Single Link® PP
uni SNB M2 20% and 20% TAB Rubber Top Single Link® DPA6.6PP
uni SNB M2 34% TAB Single Link® DPA6.6POM-D B
DPA6.6PP G
See below for specific belt types available in each width.
SLO
GB
GB K03+
SLO
uni SNB M2 20% TAB RubberTop Single Link®
59
ST
AN
DA
RD
uni SNB M2
1.296.3uni SNB M2 34%
kg/m2
POM
1.828.9
0.884.3
kg/m2
PP
1.135.5uni SNB M2 34% Rib
PE
4.4
kg/m2
-
0.90
lb/ft2
-
1.477.2 1.004.9uni SNB M2 20% 5.1 1.04
-- 1.215.9uni SNB M2 20% Rubber Top - -
161023500uni SNB M2 34%
N/m
POM
15000
N/m
PP
161023500uni SNB M2 34% Rib 15000
1028
1028
10000
N/m
PE
-
685
-
161023500uni SNB M2 20% 15000 1028 10000 685
--uni SNB M2 20% Rubber Top 15000 1028 - -
Permissible Tensile Strength
lb/ft lb/ft lb/ft
Belt material
PP PP PEPin material
Belt Weights
lb/ft2
PPPin material
lb/ft2
PP PE
Belt material
uni SNB M2 Product Support No Cling
uni SNB M2 Product SupportNo Cling
Dimensional SketchesTravel
Height
mm in.
Width Standard materials & colors
POM-D PP
2.0050.8
3.0076.2
PEType in.mm in.
K600 152.1 B G N5.99
K600 152.1 N5.99 B G
4.00101.6 K600 152.1 N5.99 B G
Standard Materials, Colors and Dimensions
Standard Selection Accessories
Only No Cling on one side and Flat on the other side.
Minimum bricklaid indent for uni SNB M2 product support is 38.0 mm (1.50 in.).Increment: 12.7 mm (0.50 in.).
60
uni SNB M2
ST
AN
DA
RD
uni SNB M2 Finger Plate Type 2
B
C
D
A
165.0
95.0
51.0
2.5
mm
6.50
3.74
2.01
E 152.1 5.99
F 100.0 3.94
G 12.0 0.47
H 10.3 0.41
I 76.0 3.00
J 6.0 0.24
M 135.0 5.31
N 23.0 0.91
O 57.0 2.24
0.10
in.
Dimensions
KPOM-EC
KPOM-EC
Standard Materials and Colors
Standard Materials and Colors
All uni-chains® belt systems that areavailable in a raised rib version canbe supplied with matching fingerplates, also called combs.
The finger plates are supplied withcover caps which can be attachedwhen the finger plate has beeninstalled. The cover caps can be re-moved by using a screwdriver thatcan be inserted between the coverand finger plate.
In order to adjust to belt width vari-ations caused by temperature fluc-tuations, a slider facilitates the side-ways movement of the finger plates(finger plate type 2).
Standard Selection Accessories
uni SNB M2 Finger Plate Type 2S
E
A
FG
N
H
O
M
J
B
A
C
D
I E
G
Snap-OnCover Caps
Snap-OnCover Caps
Slider
Only available in POM-EC black.
Only available in POM-EC black.
61
Standard Sprockets
2.5665.03.4186.53.2482.210
75332SNB10N
75332SNB10N15INSQ
75332SNB10N40MMSQ
in.in. mmmmin.mmin.mm
Hub diameterOverall diameterPitch diameterNo. ofteeth
ø0.75/1.57*ø19.1/40.0*
sq 1.50sq 38.1
sq 1.57sq 40.0
2.5665.04.06103.23.8698.112
75332SNB12N
75332SNB12N15INSQ
75332SNB12N40MMSQ
ø0.75/1.57*ø19.1/40.0*
sq 1.50sq 38.1
sq 1.57sq 40.0
2.5665.0
4.72120.0
6.01152.75.76146.318
75332SNB18N
75332SNB18N15INSQ
75332SNB18N40MMSQ
75332SNB18NBB
75332SNB18NBB60MMSQ
ø0.75/1.57*ø19.1/40.0*
sq 1.50sq 38.1
sq 1.57sq 40.0
75332SNB18NBB25INSQsq 2.50sq 63.5
ø1.57/2.76*ø40.0/ø70.0*
sq 1.57sq 60.0
75332SNB19Nø0.75/1.57*ø19.1/40.0*
Reference no. plastic
Bore
2.5665.0
6.33160.96.07154.319
75332SNB19N15INSQ
75332SNB19N40MMSQ
sq 1.50sq 38.1
sq 1.57sq 40.0
2.5665.0
4.72120.0
6.66169.16.39162.420
75332SNB20N15INSQ
75332SNB20N40MMSQ
sq 1.50sq 38.1
sq 1.57sq 40.0
75332SNB20NBB
75332SNB20NBB25INSQ
ø1.57/2.76ø40.0/70.0
sq 2.50sq 63.5
75332SNB20NBB60MMSQsq 2.36sq 60.0
Width of sprockets: 25.0 mm (0.98 in.)Tooth width: 6.0 mm (0.24 in.)
uni SNB M2 Sprocket
Belt material POM
N lb N lb
uni SNB M2 1400 315 1100 247
PP
PA6 N
Standard Material and Color
Max. Load per Sprocket
4.72120.075332SNB19NBB
75332SNB19NBB60MMSQ
ø1.57/2.76ø40.0/70.0
sq 2.36sq 60.0
ST
AN
DA
RD
uni SNB M2
Other sprocket sizes are available upon request. Two-part sprockets available upon request.Please contact uni-chains® for further information.
* Minimum/maximum round bore.
No. of
teethmm in. mm in.
10
12
18
19
34.7
43.0
45.5
53.5
77.6
81.6
1.79
2.11
3.06
3.21
67.6
71.7
1.37
1.69
2.66
2.82
20 85.6 3.37 75.8 2.98
Minimum B-dimension
Wearstrip distance A
A
B
Placement of Wearstrips and Sprockets
62
uni Flex ONE – strong, cleanable and tight radius side flexing beltuni Flex One 1.5 in. pitch was created to optimize throughput in high volume operations with space limitations. The belt is unique because it is pinless and has a higher tensile strength than all other side flexing belts in the market place.
The uni Flex One belt will increase performance in the following industries/applications:- Meat & poultry applications including tray pack conveyors, box/tote handling, freezers infeed/outfeed and other side
flexing applications- Fruit & vegetable applications including side flexing and packaging lines- Bakery applications including cooling lines, pan handling, proofers and oven infeed and takeaway- Beverage applications including case conveyors and incline/decline applications- Spiral applications including both low tension and high tension spirals- Distribution center applications including spirals and other high tension long runs
Product Features and Operational Benefits:- 80 degree high speed side flexing applications- Tight radius applications - reduced space requirements- Snap Link® design (pinless) - no pin walking- Unique safety top surface- Edge Wearparts for higher speed and load- Edge Roller Bearings for higher speed, load and no lubrication- Integrated Wearparts for cleanable applications- Easy maintenance with Snap Link® Design (pinless)
Pitch 38.1 mm (1.50 in.)
uni Flex ONE
ST
AN
DA
RD
New
64
uni Flex ONE-O
uni Flex ONE-ER
uni Flex ONE-EO uni Flex ONE-EW
Standard Selection
uni Flex ONE-O (EO)
Dimensional Sketches
Travel*
B
A
CT
P
uni Flex ONE for EO/EOO, EW, ER
Travel*
T
P
Materials
38.1 mm (1.50 in.)
See page 7 and 8
Side flexing
See page 67 and 68
See page 129
50 mm (1.8 in.)
See page 68
uni Flex ONE
B
C
A
5.9
6.6
10.0
0.23
0.26
D 9.0 0.35
E 11.0 0.43
P 38.1 1.50
T 19.1 0.75
0.39
mm in.
Dimensions
Exchangeable parts: O-Tabs (EO), Offset O-Tabs (EOO), Wearparts (EW), Edge Rollers (ER).
* uni-chains® recommends this travel direction. However, travel in both directions is possible.
Patent Pat. pending
Type Standard materials and colors
uni Flex ONE
Standard Materials and Colors
Exchangeable O-Tab, wearpart in POM-DK: O
WPOM-SX
uni Flex ONE-O (O-Tab): Using the uni Flex ONE with O-Tab and a slotted wearstrip the O-Tab will allow the transpor-ted products to be wider than the belt. O-Tabs are molded into the belt to ensure cleanability and are preferred for directfood contact.
uni Flex ONE-EO/EOO (Exchangeable O-Tab/Exchangeable Offset O-Tab): Exchangeable O-Tab system is made ofheat and wear resistant material to improve performance between belt edge and wearstrip. Using a slotted wearstrip theexchangeable O-Tab will track the belt and allow the transported products to be wider than the belt. Resists high curve loadat increased speed.
uni Flex ONE-EW (Exchangeable Wearpart): Exchangeable Wearpart system is made of heat and wear resistant materialto improve performance between belt edge and wearstrip. This Wearpart can easily be replaced. Resists high curve load atincreased speed.
uni Flex ONE-ER (Exchangeable Edge Roller): uni Flex ONE with Exchangeable Edge Rollers reduces friction in curvesto a minimum making it very suitable for applications with many curves e.g. static spirals (non rotating drum) or high speedside flexing conveyors.
ST
AN
DA
RD
uni Flex ONE-EOO
uni Flex ONE-EOO
Travel*
T
P
D
E
65
X
Belt type and widths K750
Standard Single Link® Belt Widths
uni Flex ONE-O
uni Flex ONE-EW
X
K1200 K1500 K2400
X
uni Flex ONE-EO
X
X X X X
X X X X
uni Flex ONE-ER L/R* X X X X
uni Flex ONE Single Link®
uni Flex ONE is available as Single Link® in the following standard widths:
uni Flex ONE
12.7 mm (0.50 in.)
K750 (190.5 mm (7.50 in.))
K1200 (304.8 mm (12.00 in.))
K1500 (381.0 mm (15.00 in.))
K2400 (609.6 mm (24.00 in.))
Type mm in.
Belt width
N lbf
Max. permissible load on straight section
N lbf N lbf
Max. permissible load in curves at low speed*
UHMW PEHD 1000 Nylatron, NSM
Permissible Tensile Strength
Assortment
uni Flex ONE
-O
K750 190.5 7.50 2400 540
1800 405 2000 450
1800 405 2000 450
1800 405 2000 450
2000 450 2000 450
-EW
-EO
-ER
uni Flex ONE
-O
K1200 304.8 12.00 4000 899
2700 607 3400 764
2700 607 3400 764
2700 607 3400 764
3400 764 3400 764
-EW
-EO
-ER
uni Flex ONE
-O
K1500 381.0 15.00 6400 1439
2800 629 3500 787
2800 629 3500 787
2800 629 3500 787
3500 787 3500 787
-EW
-EO
-ER
uni Flex ONE
-O
K2400 609.6 24.00 12000 2698
3200 719 3800 854
3200 719 3800 854
3200 719 3800 854
3800 854 3800 854
-EW
-EO
-ER
* Valid at 20° C (+ 68° F). Material for all types of uni Flex ONE: POM-SX.
ST
AN
DA
RD
66
Size mm in.
POM
kg/m lb/ft
Belt Weight
Assortment
uni Flex ONE-O
uni Flex ONE-EW
uni Flex ONE-EO
uni Flex ONE-ER-/ L/R*
uni Flex ONE-ER/ER
K750 190.5 7.50
2.5 1.68
2.4 1.68
2.5 1.68
2.6 1.68
2.7 1.68
uni Flex ONE-O
uni Flex ONE-EW
uni Flex ONE-EO
uni Flex ONE-ER-/ L/R*
uni Flex ONE-ER/ER
K1200 304.8 12.00
4.0 2.69
3.9 2.62
4.0 2.69
4.1 2.76
4.2 2.82
uni Flex ONE-O
uni Flex ONE-EW
uni Flex ONE-EO
uni Flex ONE-ER-/ L/R*
uni Flex ONE-ER/ER
K1500 381.0 15.00
4.9 3.29
4.9 3.29
4.9 3.29
5.0 3.36
5.1 3.43
uni Flex ONE-O
uni Flex ONE-EW
uni Flex ONE-EO
uni Flex ONE-ER-/ L/R*
uni Flex ONE-ER/ER
K2400 609.6 24.00
7.9 5.31
7.8 5.24
7.8 5.24
7.9 5.31
8.1 5.44
uni Flex ONE
* L/R = L (left)/R (right). When ordering please specify Belt Edge Configuration on opposite of edge roller (e.g. uni Flex ONE ER/EO = ER on left side and EO on right side - uni Flex ONE EW/ER = EW on left side and ER rightside.
Compression rate is 23% (e.g. 1 meter (3.28 ft) of belt can compress 0.23 m (0.75 ft) to a length of 0.77 m (2.53 ft).
Compression
ST
AN
DA
RD
67
ST
AN
DA
RDStandard Sprockets
ø2.56ø65.0
sq 1.97sq 50.03.98101.03.9299.68
8233FONE08N
8233FONE08N10INSQ
8233FONE08N30MMSQ
in.in. mmmmin.mmin.mm
Hub diameterOverall diameterPitch diameterNo. ofteeth
ø0.71/1.57*ø18.0/40.0*
sq 1.00sq 25.4
sq 1.18sq 30.0
ø2.76ø70.0
sq 2.24sq 57.04.48113.74.39111.49
8233FONE09N
8233FONE09N15INSQ
8233FONE09N40MMSQ
ø0.71/1.57*ø18.0/40.0*
sq 1.50sq 38.1
sq 1.57sq 40.0
ø2.76ø70.0
sq 2.24sq 57.0
ø3.74ø95.05.46138.85.32135.211
8233FONE11N
8233FONE11N15INSQ
8233FONE11N40MMSQ
ø0.71/1.57*ø18.0/40.0*
sq 1.50sq 38.1
sq 1.57sq 40.0
8233FONE11NBBø1.57/2.76ø 40.0/ø70.0
sq 2.95sq75.08233FONE11NBB20INSQsq 2.00sq 50.8
8233FONE11NBB60INSQsq 2.36sq 60.0
ø2.76ø70.0
sq 2.24sq 57.0
ø4.33ø110.05.95151.25.80147.212
8233FONE12N
8233FONE12N15INSQ
8233FONE12N40MMSQ
ø0.71/1.57*ø18.0/40.0*
sq 1.50sq 38.1
sq 1.57sq 40.0
8233FONE12NBBø1.57/2.76ø 40.0/ø70.0
sq 3.35sq 85.0
8233FONE12NBB20INSQsq 2.00sq 50.8
8233FONE12NBB60MMSQsq 2.36sq 60.0
8233FONE12NBB25INSQsq 2.50sq 63.5
ø2.76ø70.0
sq 2.24sq 57.0
ø4.72ø120.06.44163.66.27159.213
8233FONE13N
8233FONE13N15INSQ
8233FONE13N40MMSQ
ø0.71/1.57*ø18.0/40.0*
sq 1.50sq 38.1
sq 1.57sq 40.0
8233FONE13NBBø1.57/2.76ø 40.0/ø70.0
sq 3.35sq 85.0
8233FONE13NBB20INSQsq 2.00sq 50.8
8233FONE13NBB60MMSQsq 2.36sq 60.0
8233FONE13NBB25INSQsq 2.50sq 63.5
ø2.76ø70.0
sq 2.24sq 57.0
ø4.72ø120.07.89200.57.69195.316
8233FONE16N
8233FONE16N15INSQ
8233FONE16N40MMSQ
ø0.71/1.57*ø18.0/40.0*
sq 1.50sq 38.1
sq 1.57sq 40.0
8233FONE16NBBø1.57/2.76ø 40.0/ø70.0
sq 3.35sq 85.0
8233FONE16NBB20INSQsq 2.00sq 50.8
8233FONE16NBB60MMSQsq 2.36sq 60.0
8233FONE16NBB25INSQsq 2.50sq 63.5
Reference no. plastic
Bore
uni Flex ONE
* Minimum/maximum round bore.
68
uni Flex ONE
Width of sprockets: 39.0 mm (1.54 in.)Tooth width: 9.0 mm (0.35 in.)
uni Flex ONE Sprocket
Standard Sprockets
PA6 G
Standard Material and Color
uni-chains® provides an extensive range of sprockets to drive the uni Flex ONE belts. During years of field experience thesprocket profiles have been developed to ensure maximum operating performance.
No. of
teethmm in. mm in.
8
9
11
12
58.9
64.9
36.5
42.8
55.3
61.6
1.44
1.69
2.18
2.43
76.9
82.9
2.32
2.56
3.03
3.26
13 67.8 2.67 88.9 3.50
16 86.2 3.40 107.0 4.21
Minimum B-dimension
Wearstrip distance A
A
B
Placement of Wearstrips and Sprockets
Placement and Number of Sprockets
B
C
A
78.5
52.0
56.0
3.10
2.05
D 88.8 3.50
E 61.0 2.40
F 104.0 4.10
G 81.6 3.21
2.20
mm in.
A B
A C D D
A C C E C C
A F F G F F
uni Flex ONE K750
uni Flex ONE K1200
uni Flex ONE K1500
uni Flex ONE K2400
Thickness of Idler: 20.0 mm (0.79 in.)
uni Flex ONE Idler
Standard Selection Accessories
N
Standard Material and Color
POM-D
No. of
teethmm in.
8
9
11
12
72.9
85.6
110.7
123.1
2.87
3.37
4.36
4.85
13 135.5 5.33
16 172.4 6.79
Diameter Idler
Recommended for use at idler end to ensure smooth andlow noise operation.
ST
AN
DA
RD
69
uni SSB – strong and solid wear resistant beltThe uni SSB 1.5 in. pitch belt was created to be used in heavy duty applications such as accumulation tables, packagingapplications or other areas where wear resistance is needed. The uni SSB belt may be used together with uni SSB mold-to-width chains in de-combiners or combiners to increase conveyor speed and product throughput.
The uni SSB belt has increased performance in the following industries/applications:- Fruit & vegetable applications including filling lines, canning lines, accumulation tables and incline/decline
applications- Bakery and snack food applications including cooling lines, pan handling, oven infeed and takeaway- Beverage applications including case conveyors, denester lines, de-combiners, accumulation tables, incline/decline
applications- Can manufacturing applications including mass handling, transfer conveyors, accumulation tables and palletizers
infeed conveyors- Material handling applications including mass handling, accumulation tables, palletizers and packaging areas
Product features and operational benefits:- Closed and wide hinge design increases product stability and decreases pin wear- Chamfered edges allow stability in side transfer applications - Unique locking systems (no pin walking or pins coming out)- Unique open area for cooling conveyors and incline drainage applications
Pitch 38.1 mm (1.50 in.)
uni SSB
US
ST
AN
DA
RD
70
US
ST
AN
DA
RD
uni SSB
uni SSB C
uni SSB TAB
uni SSB 29% uni SSB 32%
Standard Selection
uni SSB
Dimensional Sketches
Travel
T EL
P
uni SSB TAB
Travel
TR
EL
P
1.39 35.2C
0.77 19.6 D
0.26 6.5 E0.16 4.0B
0.39 10.0 A 1.50 38.1 P
0.39 10.0 R
0.50 12.7 T0.25 6.4L
mm
Dimensions
Materials
Accessories
38.1 mm (1.50 in.)
See page 7 and 8
Straight running
See page 72
See page 72
See page 71
45 mm (1.8 in.)
Alternative
Standard locksType
Standard materials and colors
Standard pins
Materials and colors Materials and colors
Standard Materials and Colors
uni SSB C and uni SSB TAB
uni SSB 29%
uni SSB 32%
G
BRPOM-LF
BRPOM-LF
BRPOM-LF
PP
GPP
N BGR
NGR
NGR
PP
BPP
BPP
GPP NGR BPP
BPPNGR
BPPNGR
mm
76
152
228
304
380
456
532
607
683
759
3.0
6.0
9.0
12.0
15.0
18.0
20.9
23.9
26.9
29.9
mm
835
911
987
1063
1139
1216
1291
1367
1443
1519
32.9
35.9
38.9
41.9
44.9
47.9
50.8
53.8
56.8
59.8
mm
1595
1671
1747
1823
1899
1975
2051
2127
2203
2279
62.8
65.8
68.8
71.8
74.8
77.8
80.8
83.7
86.7
89.7
mm
2355
2431
2507
2583
2659
2735
2811
2887
2963
3039
92.7
95.7
98.7
101.7
104.7
107.7
110.7
113.7
116.6
119.6
in. in. in. in. mm in.
Standard Bricklayed Belt Widths (See next page for Single Link® widths)
WPP
SS304
uni SSB TAB
T
CA
D B
in. mm in. mm in.
See page 129
71
uni SSB
US
ST
AN
DA
RD
X
Belt type and widths K300
Standard Single Link® Belt Widths
uni SSB C
uni SSB C TAB
K325 K450 K600
uni SSB 29%
X
X X
K750
uni SSB 32% X X
SLO
SLO
SLO SLO
uni SSB Single Link®
uni SSB is also available as Single Link® in the following standard widths:
2.3111.3uni SSB
kg/m2
GR
POM
2.2711.1
kg/m2
PP
2.7913.6
kg/m2
2.3111.3
kg/m2
GR
PP
2.2711.1
kg/m2
PP
2.7913.6
kg/m2
246736000uni SSB
N/m
POM
132919400
N/m
GR
6379300
N/m
PP
123318000
N/m
PP
89113000
N/m
GR
75411000
N/m
PP
lb/ft2
Pin material
lb/ft2 lb/ft2
steel
lb/ft2 lb/ft2 lb/ft2
steel
Belt material
Permissible Tensile Strength
lb/ft
steel
lb/ft lb/ft lb/ft
steel
lb/ft lb/ft
Belt material
Pin material
Belt Weights
Height S
mm in.Style
Width
76.1 3.00 flat
mm in.
152.2 5.99K600
uni SSB Product Support
S
PP-I G
Standard Materials, Colors and DimensionsStandard Selection Accessories
K300 (76.0 mm (2.99 in.))
K325 (82.3 mm (3.24 in.))
K450 (114.1 mm 4.49 in.))
K600 (152.2 mm (5.99 in.))
K750 (190.2 mm (7.49 in.))
A* F*
*Depending on thewidth the SSB belt isbricklayed with 2 different K300 mo-dules called "A" and"F."For belt widths that aremultiples of 6 in. an"A" and an "F" moduleare used on oppositesides every other pitch.For other belt widthsonly an "F" module isused on alternatingsides every pich.
Minimum bricklaid indent for uni SSB product support is 50.8 mm (2.00 in.).Increment: 25.4 mm (1.00 in.).
SLO = Single Link® only
72
US
ST
AN
DA
RD
uni SSB
Standard Sprockets - Single row
2.9575.04.61117.14.62117.319 1633SSB19N
in.in. mmmmin.mmin.mm
Hub diameterOverall diameterPitch diameterNo. ofteeth
ø0.71/1.57*ø18.0/40.0*
Reference no. plastic
2.9575.05.12130.05.09129.321 1633SSB21Nø0.71/1.57*ø18.0/40.0*
2.9575.05.59142.05.56141.223 1633SSB23Nø0.71/1.57*ø18.0/40.0*
2.9575.06.07154.26.03153.225 1633SSB25Nø0.71/1.57*ø18.0/40.0*
Bore
Standard Sprockets - Two-part single row
2.2858.04.61117.14.62117.319 1633SSB19NT
in.in. mmmmin.mmin.mm
Hub diameterOverall diameterPitch diameterNo. ofteeth
ø0.71/1.57*ø18.0/40.0*
Reference no. plastic
2.2858.05.12130.05.09129.321 1633SSB21NTø0.71/1.57*ø18.0/40.0*
2.2858.05.59142.05.56141.223 1633SSB23NTø0.71/1.57*ø18.0/40.0*
2.2858.06.07154.26.03153.225 1633SSB25NTø0.71/1.57*ø18.0/40.0*
Bore
Width of sprockets: 42.3 mm (1.67 in.)Tooth width: 15.0 mm (0.59 in.)
uni SSB sprocket
PA6 N
Other sprocket sizes are available upon request. Two-part sprockets available upon request.
Please contact uni-chains® for further information.
Note: uni SSB can also be driven by uni 820 chain sprockets except uni SSB-K325 and K450.
* Minimum/maximum round bore.
Standard Material and Color
Width of sprockets: 42.3 mm (1.67 in.)Tooth width: 15.0 mm (0.59 in.)
uni SSB sprocketTwo-part single row
PA6 N
Other sprocket sizes are available upon request. Two-part sprockets available upon request.
Please contact uni-chains® for further information.
Standard Material and Color
* Minimum/maximum round bore.
No. of
teethmm in. mm in.
19
21
23
25
49.5
55.8
65.4
71.4
77.4
83.4
2.57
2.81
3.05
3.28
62.1
68.3
1.95
2.20
2.44
2.69
Minimum B-dimension
Wearstrip distance A
A
B
Placement of Wearstrips and Sprockets
73
uni Light EP
uni Light EP – light duty application beltThe uni Light EP 1.5 in. pitch belt design is developed for light duty applications such as cooking, blanching and pasteurizing in the food industry. The different openings allow high performance with various food products.
The uni Light EP belt is commonly used in the following industries/applications:- Fruit & vegetable applications including elevators, blanchers, cooking lines and pasteurizers- Pasta applications including blanchers, pasteurizers and cooling lines- Agriculture (corn & rice) applications including elevators, blanchers and cooking lines- Beverage applications including accumulation tables, pasteurizers and palletizers
Product features and operational benefits:- Various openings including fine-mesh for water drainage- Steel reinforcement feature eliminates belt elongation in high temperature applications - Reinforced product supports for high load elevators and incline conveyors
Pitch 38.1 mm (1.50 in.)
ST
AN
DA
RD
74
WPE
SS304
WPP
38.1 mm (1.50 in.)
Straight running
See page 76
Reinforcement Links: See page 75 for further information.
75 mm (3.0 in.)
Materials See page 9
ST
AN
DA
RD
uni Light EP
uni Light EP22% fine-meshed
uni Light EPwith Reinforcement Links
Standard Selection
uni Light EP
Dimensional Sketches
E
Travel
P
L
T
Standard locksType
Standard materials and colors
Standard pins
Materials and colors Materials and colors
Standard Materials and Colors
uni Light EP 22% fine-meshed WPPHW WPP WPP
BPPHW WPP WPP
Alternative
L
T
E
4.3
8.5
5.1
0.17
P 38.1 1.50
0.34
0.20
mm in.
Dimensions
Accessories
mm
102
152
254
305
355
406
458
509
559
610
6.0
10.0
12.0
14.0
16.0
18.0
20.0
22.0
24.0
mm
661
712
763
814
865
916
966
1017
1068
1119
26.0
28.0
30.0
32.0
34.0
36.0
38.0
40.0
42.0
44.0
mm
1170
1220
1271
1322
1373
1424
1474
1525
1576
1627
46.0
48.0
50.0
52.0
54.0
56.0
58.0
60.0
62.0
64.0
mm
1678
1728
1779
1830
1881
1932
1982
2033
2084
2135
66.0
68.0
70.0
72.0
74.0
76.0
78.0
80.0
82.0
84.0
mm
2186
2236
2287
2338
2389
2440
-
-
-
-
86.0
88.0
90.0
92.0
94.0
96.0
-
-
-
-
in. in. in. in. in.
Standard Bricklayed Belt Widths (See next page for Single Link® widths)
SS316
4.0
Patent Patented
See page 129
75
uni Light EP Single Link®
uni Light EP is also available as Single Link® in the following standard widths:
K250 (63.5 mm (2.50 in.))
K400 (101.6 mm (4.00 in.))
K600 (152.8 mm (6.02 in.))
K750 (191.0 mm (7.52 in.))
uni Light EP
ST
AN
DA
RD
70210250uni Light EP 22% fine-meshed
N/m
POM
3515125
N/m
PP PE
2113075
N/m
Permissible Tensile Strength
lb/ft lb/ft lb/ft
Belt material
2251000uni Light EP 22% fine-meshed
N/pcs
Load Capacity per Reinforcement Linklb/pcs
kg/m2
POM
0.984.8uni Light EP 22% fine-meshed
kg/m2
1.728.4
kg/m2
PP
0.703.4
kg/m2
1.437.0
kg/m2
PE
0.743.6
kg/m2
1.487.2
Belt Weights
lb/ft2
plasticPin material
lb/ft2
steel
lb/ft2
plastic
lb/ft2
steel
lb/ft2
plastic
lb/ft2
steel
Belt material
The use of uni-chains® belt with the SS reinforcement /pitchcontrol links in blanchers, cookers and other high tem-perature applications will reduce belt elongation due to temperature by more than 90%. This will simplify the belttake-up system and reduce maintenance.
uni-chains® recommends 1 reinforcement link per K600module.
76
ST
AN
DA
RD
uni Light EP
Standard Sprockets
2.5665.03.3986.03.4687.87 2533EP07N
in.in. mmmmin.mmin.mm
Hub diameterOverall diameterPitch diameterNo. ofteeth
ø0.71/1.57*ø18.0/40.0*
3.5490.04.35110.64.39111.492533EP09N
2533EP09N15INSQ
ø0.71/2.76*ø18.0/70.0*
sq 1.50sq 38.1
3.94100.04.83122.74.85123.310
2533EP10N
2533EP10N15INSQ
ø0.71/2.76*ø18.0/70.0*
sq 1.50sq 38.1
2533EP10N40MMSQsq 1.57sq 40.0
4.33110.05.31134.95.32135.211 2533EP11Nø0.71/2.76*ø18.0/70.0*
4.72120.05.79147.15.80147.212
2533EP12Nø0.71/2.76*ø18.0/70.0*
4.72120.07.23183.67.22183.315 2533EP15Nø0.71/1.57*ø18.0/40.0*
Reference no. plastic
Bore
2533EP12N15INSQsq 1.50sq 38.1
2533EP12N40MMSQsq 1.57sq 40.0
Width of sprockets: 23.2 mm (0.91 in.)Tooth width: 11.8 mm (0.47 in.)
uni Light EP sprocket
PA6 N
Other sprocket sizes are available upon request. Two-part sprockets available upon request.
Please contact uni-chains® for further information.
* Minimum/maximum round bore.
Standard Material and Color
No. of
teethmm in. mm in.
7
9
10
11
35.2
48.0
48.3
60.0
66.0
72.0
1.90
2.36
2.60
2.83
54.3
60.5
1.39
1.89
2.14
2.38
12 78.0 3.07 66.7 2.62
15 96.0 3.78 85.3 3.36
Minimum B-dimension
Wearstrip distance A
A
B
Placement of Wearstrips and Sprockets
77
uni L-SNB – the heavy duty open top and rib top beltThe Large SNB 2 in. pitch belt was designed for heavy duty applications in various industries. The unique surface profilelimits friction and contact between products and belt and increases airflow. The L-SNB belt has the unique stainless steelreinforcement link feature which allows pitch control in high or low temperature applications.
The uni L-SNB belt increases performance in the following industries/applications:- Meat applications including microwaves, cooling and freezing lines- Fruit & vegetable applications including de-watering lines, cooling and freezing lines- Pasta applications including blanchers, pasteurizers and cooling lines- Beverage applications including accumulating tables, pasteurizers and palletizers- Can manufacturing applications including accumulation tables, mass handling and palletizers
Product features and operational benefits:- Less friction and product contact – for easy cooking, cooling and freezing of products- Large open area for easy drainage- Steel reinforcement feature reduces belt elongation in high temperature applications - Easy cleaning – less maintenance and downtime - Finger plates for trouble free transfer- Small backflex radius for lower profile conveyors
Pitch 50.0 mm (1.97 in.)
uni L-SNB
ST
AN
DA
RD
78
ST
AN
DA
RD
uni L-SNB
uni L-SNB uni L-SNB Rib
Standard Selection
Surface opening 36% Surface opening 36%
WPE
SS304
50.0 mm (1.97 in.)
See page 7 and 8
Straight running
Materials
70 mm (2.8 in.)uni L-SNB Rib:140 mm (5.5 in.)
See page 81
See page 80
Accessories
Alternative
uni L-SNB
Dimensional SketchesTravel
T
EL
P
uni L-SNB Rib
Travel
T
EL
P
R
L
E
8.0
8.3
mm
0.31
0.33
in.
R
P
6.0
50.0
mm
0.23
1.97
in
-
T
-
16.0
mm
-
0.63
in.
Dimensions
Standard locksType
Standard materials and colors
Standard pins
Materials and colors Materials and colors
Standard Materials and Colors
uni L-SNB
uni L-SNB Rib
W
BRPOM-LF
PP
GPP
WPP WPP
NPP WPP NPP
GPP
GPP
WPP
WPP
mm
152
228
304
380
456
532
608
684
760
836
6.0
9.0
12.0
15.0
18.0
20.9
23.9
26.9
29.9
32.9
mm
912
988
1064
1140
1217
1293
1369
1445
1521
1597
35.9
38.9
41.9
44.9
47.9
50.9
53.9
56.9
59.9
62.9
mm
1673
1749
1825
1901
1977
2053
2129
2205
2281
2357
65.9
68.9
71.9
74.8
77.8
80.8
83.8
86.8
89.8
92.8
mm
2433
2509
2585
2661
2737
2813
2889
2965
3041
3117
mm
95.8
98.8
101.8
104.8
107.8
110.7
113.7
116.7
119.7
122.7
in. in. in. in. in.
Standard Bricklayed Belt Widths (See next page for Single Link® widths)
SS316
Patent Patented
See page 129
79
uni L-SNB
ST
AN
DA
RDuni L-SNB Single Link®
uni L-SNB is also available as Single Link® in the following standard widths:
K600 (151.4 mm (5.96 in.))
K1200 (304.3 mm (11.98 in.))
239835000uni L-SNB
N/m
POM
119917500
N/m
PP
376855000uni L-SNB-Rib 204229800
Permissible Tensile Strength
lb/ft lb/ft
Belt material
2.0910.2uni L-SNB
kg/m2
plastic
POM
3.5017.1
kg/m2
steel
Belt Weights
lb/ft2
Pin material
lb/ft2
1.376.7
kg/m2
plastic
PP
2.8313.8
kg/m2
steel
lb/ft2 lb/ft2
1.457.1
kg/m2
plastic
PE
2.8714.0
3.0314.8uni L-SNB-Rib 4.4621.8 2.019.8 3.4216.7 2.0710.1 3.4817.0
kg/m2
steel
lb/ft2 lb/ft2
Belt material
2472500uni L-SNB
N/pcs
Load Capacity per Reinforcement Linklb/pcs
The use of uni-chains® belt with the SS reinforcement/pitchcontrol links in blanchers, cookers and other high tempera-ture applications will reduce belt elongation due to tempera-ture by more than 90%. This will simplify the belt take-upsystem and reduce maintenance.
uni-chains® recommends 3 reinforcement links per K1200 module.
80
Standard Sprockets
2.9575.03.6492.53.94100.06 2033LSNB06N
in.in. mmmmin.mmin.mm
Hub diameterOverall diameterPitch diameterNo. ofteeth
ø0.71/1.57*ø18.0/40.0*
Reference no. plastic
2.9575.06.29159.86.37161.810
2033LSNB10Nø0.71/1.57*ø18.0/40.0*
4.72120.0 2033LSNB10NBBø1.57/2.76*ø40.0/70.0*
2.9575.07.58192.57.61193.212
2033LSNB12Nø0.71/1.57*ø18.0/40.0*
4.72120.0 2033LSNB12NBBø1.57/2.76*ø40.0/70.0*
2.9575.05.06128.65.15130.78
2033LSNB08Nø0.71/1.57*ø18.0/40.0*
4.72120.0 2033LSNB08NBBø1.57/2.76*ø40.0/70.0*
Bore
4.72120.010.13257.310.09256.316 2033LSNB16NBBø1.57/2.76*ø40.0/70.0*
Width of sprockets: 42.3 mm (1.67 in.)Tooth width: 7.0 mm (0.28 in.)
uni L-SNB sprocket
PA6 N
Other sprocket sizes are available upon request. Two-part sprockets available upon request.
Please contact uni-chains® for further information.
* Minimum/maximum round bore.
Standard Material and Color
ST
AN
DA
RD
uni L-SNB
No. of
teethmm in. mm in.
6
8
10
12
35.3
52.4
58.0
73.3
88.9
104.6
2.28
2.89
3.50
4.12
69.0
85.3
1.39
2.06
2.72
3.36
16 136.1 5.36 117.7 4.63
Minimum B-dimension
Wearstrip distance A
A
B
Placement of Wearstrips and Sprockets
81
uni L-SNB Finger Plate Type A
uni L-SNB Finger Plate Type B
BRPOM-LF
Standard Materials and Colors
G F E
N
I
J
K
A
H
EG
H
N
O
M
A
F
Snap-OnCover Caps
GPOM-DI
BRPOM-LF
Standard Materials and Colors
GPOM-DI
E
F
G
A
152.1
100.3
12.0
2.5
mm
5.99
3.95
0.47
H 10.0 0.39
I 80.0 3.15
J 114.0 4.49
K 192.0 7.56
M 135.0 5.31
N 23.0 0.91
O 57.0 2.24
0.10
in.
Dimensions
uni L-SNB
ST
AN
DA
RD
All uni-chains® belt systems that areavailable in a raised rib version canbe supplied with matching fingerplates, also called combs.
The finger plates are supplied withcover caps which can be attachedwhen the finger plate has beeninstalled. The cover caps can be re-moved by using a screwdriver thatcan be inserted between the coverand finger plate.
In order to adjust to belt width vari-ations caused by temperature fluc-tuations, a slider facilitates the side-ways movement of the finger plates.
Standard Selection Accessories
Snap-OnCover Caps
Slider
Slider
ST
AN
DA
RD
82
uni OPB
uni OPB – the open belt with a unique top and bottom surface The uni OPB 2 in. pitch belt is developed for the processes of cooking, blanching and pasteurizing in the food industry. The different openings provide high performance with various food products.
The uni OPB belt is commonly used in the following industries/applications:- Fruit & vegetable applications including elevators, blanchers, cooking lines and pasteurizers- Pasta applications including blanchers, pasteurizers and cooling lines- Agriculture (corn & rice) applications including elevators, blanchers and cooking lines- Beverage applications including accumulating tables, pasteurizers and palletizers
Product features and operational benefits:- Small or large opening including fine mesh for water drainage- Steel reinforcement feature reduces belt elongation in high temperature applications - Wear and impact resistant bottom surface - Reinforced product supports for high load elevators and incline conveyors- Finger plates for trouble free transfer
Pitch 50.0 mm (1.97 in.)
83
uni OPB
uni OPB 4V-23%
uni OPB 4V-36%
uni OPB 4V-23% fine meshed
Standard Selection
uni OPB 4V-23% Rib
uni OPB 4V
Dimensional SketchesTravel*
V
EL
P
uni OPB 4V-Rib
Travel*
V
EL
PR
B
W WPP PE
SS316
GWPP
BWPE
50.0 mm (1.97 in.)
See page 7, 8 and 9
Straight running
Materials
75 mm (3.0 in.)Rib: 300 mm (11.8 in.)Side guards: 200 mm (7.9 in.)
Accessories
See page 86
See page 86
See page 87
See page 85
Alternative
TypeStandard materials
and colors
Pins
Materials and colors
Standard Materials and Colors
uni OPB 4V-23%
uni OPB 4V-23% fine meshed
WPPBPPHW
BPPHW
uni OPB 4V-23% Rib WPPGPP
uni OPB 4V-36% WPPPP
WPP
mm
151
185
268
302
335
386
403
418
452
486
in.
5.9
7.3
10.6
11.9
13.2
15.2
15.9
16.5
17.8
19.1
mm
503
536
570
603
636
703
754
788
804
872
in.
19.8
21.1
22.4
23.7
25.0
27.7
29.7
31.0
31.7
34.3
mm
905
938
988
1022
1055
1206
1357
1508
1659
1810
in.
35.6
36.9
38.9
40.2
41.5
47.5
53.4
59.4
65.3
71.2
mm
1960
2111
2262
2413
2564
2714
2865
3016
3167
3318
in. mm in.
77.2
83.1
89.1
95.0
100.9
106.9
112.8
118.7
124.7
130.6
Standard Bricklayed Belt Widths (See next page for Single Link® widths)
SS316
Note: uni OPB 4V-23%, uni OPB 4V 23% Rib and uni OPB 4V-36%are listed in the USDA "Accepted Meat and Poultry Equipment" pub-lication as accepted for food contact.
* uni-chains® recommends this travel direction. However, travel inboth directions is possible.
Bottom uni OPB 4V
Tra
vel
L
E
8.0
8.3
mm
0.31
0.33
in.
R
P
10.0
50.0
mm
0.39
1.97
in.
-
V
-
16.0
mm
-
0.63
in.
Dimensions
Patent Patented
W
See page 129
ST
AN
DA
RD
ST
AN
DA
RD
84
uni OPB
uni OPB Single Link®
uni OPB is also available as Single Link® in the following standard widths:
Standard Single Link® Belt Widths
K475 (117.4 mm (4.62 in.))
K600 (151.0 mm (5.94 in.))
K725 (184.6 mm (7.27 in.))
Belt type and widthsK475
117.4 mm (4.62 in.)
uni OPB 4V-23%
K600 151.0 mm(5.94 in.)
K725184.6 mm(7.27 in.)
uni OPB 4V-23% fine meshed
X X X
X X X
uni 4V-23% Rib X
uni 4V-36% X
150722000uni OPB 4V
POM
75411000
PP
4526600
PE
Permissible Tensile Strength
lb/ftN/m lb/ftN/m lb/ftN/m
Belt material
3.0014.6uni OPB Rib
2.0710.1uni OPB 23%/fine-meshed
POM
4.3221.1
3.3016.1
1.919.3
1.416.9
PP
3.2215.7
2.7413.4
2.0710.1
1.507.3
PE
3.3716.5
1.959.5uni OPB 36% 3.1315.3 1.296.3 2.6212.8 1.376.7 2.7013.2
2.8313.8
Belt Weights
lb/ft2kg/m2
plastic steelPin material
lb/ft2kg/m2 lb/ft2kg/m2
plastic steel
lb/ft2kg/m2 lb/ft2kg/m2
plastic steel
lb/ft2kg/m2
Belt material
2472500uni OPB
N/pcs
Load Capacity per Reinforcement Linklb/pcs
The use of uni-chains® belt with the SS reinforcement /pitchcontrol links in blanchers, cookers and other high tempera-ture applications will reduce belt elongation due to tempera-ture by more than 90%. This will simplify the belt take-upsystem and reduce maintenance.
uni-chains® recommends 1 reinforcement link per K600module.
85
uni OPB
Standard Sprockets
2.5665.03.7294.53.94100.06
2433OPBS06N
2433OPBS06N15INSQ
2433OPBS06N40MMSQ
in.in. mmmmin.mmin.mm
Hub diameterOverall diameterPitch diameterNo. ofteeth
ø0.71/1.57*ø18.0/40.0*
sq 1.50sq 38.1
sq 1.57sq 40.0
2.5665.05.08129.05.15130.78
2433OPBS08N
2433OPBS08N15INSQ
2433OPBS08N40MMSQ
ø0.71/1.57*ø18.0/40.0*
sq 1.50sq 38.1
sq 1.57sq 40.0
2.5665.0
4.72120.0
6.30160.16.37161.810
2433OPBS10N
2433OPBS10N15INSQ
2433OPBS10N40MMSQ
2433OPBS10NBB
ø0.71/1.57*ø18.0/40.0
sq 1.50sq 38.1
sq 1.57sq 40.0
ø1.57/2.76*ø40.0/ø70.0*
Reference no. plastic
Bore
2.5665.07.54191.57.61193.212
2433OPBS12N
2433OPBS12N15INSQ
2433OPBS12N40MMSQ
ø0.71/1.57*ø18.0/40.0*
sq 1.50sq 38.1
sq 1.57sq 40.0
4.72120.0 2433OPBS12NBBø1.57/2.76*ø40.0/ø70.0*
2.8372.0
5.91150.08.16207.38.22208.913
2433OPBS13N
2433OPBS13NBB
ø0.71/1.57*ø18.0/40.0*
sq 1.50sq 38.1
4.72120.010.04254.910.09256.316 2433OPBS16NBBø1.57/2.76*ø40.0/ø70.0*
Width of sprockets: 42.3 mm (1.67 in.)Tooth width: 11.0 mm (0.43 in.)
uni OPB sprocket
PA6 N
Other sprocket sizes are available upon request. Two-part sprockets availableupon request.
Please contact uni-chains® for further information.
* Minimum/maximum round bore.
Standard Material and Color
No. of
teethmm in. mm in.
6
8
10
12
35.3
52.4
58.5
73.8
89.4
105.1
2.30
2.91
3.52
4.14
68.9
85.3
1.39
2.06
2.71
3.36
13 113.0 4.45 93.4 3.68
16 136.6 5.38 117.7 4.63
Minimum B-dimension
Wearstrip distance A
A
B
Placement of Wearstrips and SprocketsS
TA
ND
AR
D
ST
AN
DA
RD
86
uni OPB
uni OPBProduct Support No Cling
Dimensional Sketches
uni OPB Product Support No Cling with Ribs
Height
mm in.Style
Width Standard materials & colors
PPHWmm in.
K600 151.0 5.94OPB 4V PS No Cling
OPB 4V PS No Cling with Ribs
2.0050.8
3.0076.2
4.00101.6
2.0050.8
3.0076.2
4.00101.6
K600 151.0 5.94
OPB 4V-23F PS No Cling
OPB 4V-23F PS No Cling with Ribs
4.00101.6
3.0076.2
4.00101.6
B
B
K600 151.0 5.94 B
K600 151.0 5.94 B
Standard Materials, Colors and Dimensions
CB
A
uni OPB Side Guard
P
Travel
Dimensions
B
D*
A
77.2
21.0
102.6
mm
3.04
C 51.8 2.04
0.83
E* 34.0 1.34
P 50.0 1.97
4.04
in.
PA6
Standard Material and Color
B
TravelTravel
Standard Selection Accessories
Standard Selection Accessories
* Min. indent.Increment: 8.4 mm (0.33 in.).
uni OPB Product Support No Cling with Ribsuni OPB Product Support No Cling
D
E
D
Tra
vel
E
87
uni OPB
uni OPB Finger Plate Type 1A
uni OPB Finger Plate Type 2
Standard Materials and Colors
GPOM-DI
Standard Materials and Colors
GPOM-DI
Dimensions
EF
H
A
B
L
D
C
G
Snap-OnCover Caps
B
C
D
A
220.0
150.0
75.0
2.8
8.66
5.91
2.95
E 149.0 5.87
F 100.0 3.94
G 12.0 0.47
H 9.0 0.35
L 119.0 4.69
M 123.0 4.84
N 22.0 0.87
O 53.0 2.09
0.11
mm in.
All uni-chains® belt systems that areavailable in a raised rib version canbe supplied with matching fingerplates, also called combs.
The finger plates are supplied withcover caps which can be attachedwhen the finger plate has beeninstalled. The cover caps can be re-moved by using a screwdriver thatcan be inserted between the coverand finger plate.
Standard Selection Accessories
ST
AN
DA
RD
H
M
O
N
G F E
A
Snap-OnCover Caps
ST
AN
DA
RD
88
uni CPB
uni CPB – a strong and wear resistant beltThe uni CPB 2 in. pitch, straight running belt was created for heavy duty conveyors. It replaces steel slat top chains andother technologies being used for high wear or heavy duty applications.
The uni CPB (Closed and Rough Top) belts have increased performance in the following industries/applications:- Automotive applications including manrider belts, car conveyors, leak tests- Carwash applications including carwash, interior detailing areas- Material handling applications including pallet handling and other heavy duty product applications- Meat (beef & pork) applications including hook lines and hide takeaway conveyors- Bakery applications including stacked pan handling and packaging lines- People moving applications including ski lifts and amusement parks
Product features and operational benefits:- No lubrication required- Easy maintenance and less downtime – unique locking system (lockpin)- Reduced noise level- Extremely wear and impact resistant- Unique sprocket engagement allows long conveyors with reduced pulsation - Rough top surface reduces slippage and allows safe movements
Pitch 50.8 mm (2.00 in.)
New
89
uni CPB
uni CPB C uni CPB 20% Rough uni CPB C Rough
Standard Selection
50.8 mm (2.00 in.)
Straight running
See page 91 and 92
85 mm (3.3 in.)
See page 7 and 8Materials
TypeStandard materials
and colors
Pins
Material and color
Standard Materials and Colors
uni CPB C
uni CPB 20% Rough
K
KPOM-NL
KPOM-NL
NPA6.6
GPP NPA6.6
NPA6.6
NPA6.6
uni CPB C Rough KPOM-NL NPA6.6
POM-NLAS
KPOM-NLAS
NPA6.6
uni CPB C
Dimensional SketchesTravel
E L
P
uni CPB 20% Rough, C Rough
Travel
V T
P
S
E L 0.041.0S
0.7118.0T
0.7519.0V
2.0050.8P
0.31 8.0L
0.338.3E
mm in.
Dimensions
mm
150
200
250
300
350
401
451
5.9
7.9
9.8
11.8
13.8
15.8
17.8
mm
501
551
601
651
701
751
21.7
23.7
25.6
27.6
29.6
1201
1252
1302
1352
1402
47.3
49.3
51.3
53.2
55.2
1852
1902
1952
2002
72.9
74.9
76.9
78.8
2052
2102
80.8
82.8
801
851
901
951
100119.7
31.5
33.5
35.5
37.4
39.4
1051 41.4
1101 43.3
1151 45.3
mm
1452
1502
1552
1602
1652
1702
1752
57.2
59.1
61.1
63.1
65.0
67.0
69.0
1802 70.9
in. in. in.
Standard Bricklayed Belt Widths (See next page for Single Link® widths)in.
Accessories
See page 90
mm
See page 129
ST
AN
DA
RD
ST
AN
DA
RD
90
uni CPB
uni CPB C, 20% /C Rough
N/m
52000
PA6.6
3563
Pin material
lb/ft N/m
35000
PA6.6
PP
2398
lb/ft
Permissible Tensile Strength
kg/m2
16.6
PA6.6
3.40
Belt Weights
uni CPBC, 20%/C Rough
Pin material
Belt material
lb/ft2
POM
kg/m2
11.1
PA6.6
2.27
lb/ft2
PP
Belt material
Height
mm in.
Width
K600 150.5
Standard material & color
POM-NLAS
1.0025.4 K
Type mm in.
5.93
uni CPB Product Support flat (no Ribs)
uni CPBProduct Support flat (no Ribs)
Dimensional Sketch
Travel
Standard Materials, Colors and Dimensions
uni CPB Single Link®
uni CPB is also available as Single Link® in the following standard width:
K600 (150.5 mm (5.93 in.))
Standard Selection Accessories
POM
R
0.225.5R
mm in.
Dimensions
Distance between product support is 30.0 mm (1.18 in.).
91
uni CPB
Standard Sprockets
uni CPB Sprocket
PA6 N
Width of sprockets: 42.3 mm (1.67 in.)Tooth width: 9.5 mm (0.37 in.)
Other sprocket sizes are available upon request. Two-part sprocketsavailable upon request.Please contact uni-chains® for further information.
Please note, if travel is in both directions, an extra set of sprocketsis required or use Bi-directional options. (See next page.)
* Minimum/maximum round bore.
Standard Material and Color
2.5665.03.9299.54.00101.66
1833MPB06N
1833MPB06N15INSQ
1833MPB06N40MMSQ
in.in. mmmmin.mmin.mm
Hub diameterOverall diameterPitch diameterNo. ofteeth
ø0.71/1.57*ø18.0/40.0*
sq 1.50sq 38.1
sq 1.57sq 40.0
2.5665.05.23132.95.23132.88
1833MPB08N
1833MPB08N15INSQ
1833MPB08N20INSQ
ø0.71/1.57*ø18.0/40.0*
sq 1.50sq 38.1
1833MPB08N40MMSQsq 1.57sq 40.0
sq 2.00sq 50.8
2.5665.0
4.72120.0
6.53165.86.47164.410
1833MPB10N
1833MPB10N15INSQ
1833MPB10NBB
1833MPB10NBB25INSQ
ø0.71/1.57*ø18.0/40.0*
sq 1.50sq 38.1
ø1.57/2.76*ø40.0/ø70.0*
1833MPB10NBB20INSQsq 2.00sq 50.8
sq 2.50sq 63.5
1833MPB10NBB60MMSQsq 2.36sq 60.0
Reference no. plastic
Bore
2.5665.0
4.72120.0
7.82198.67.73196.312
1833MPB12N15INSQ
1833MPB12N40MMSQ
1833MPB12NBB
sq 1.50sq 38.1
sq 1.57sq 40.0
1.57/2.76*ø40.0/ø70.0*
1833MPB12NBB20INSQsq 2.00sq 50.8
1833MPB12NBB40MMSQsq 1.57sq 40.0
1833MPB12NBB60MMSQsq 2.36sq 60.0
2.8372.0
5.91150.010.04255.010.25260.416
1833MPB16N
1833MPB16NBB
ø0.71/1.57*ø18.0/40.0*
1.57/2.76*ø40.0/ø70.0*
1833MPB10N40MMSQsq 1.57sq 40.0
1833MPB12Nø0.71/1.57*ø18.0/40.0*
Belt material POM
N lb
uni CPB 2500 560
Max. Load per Sprocket
No. of
teethmm in. mm in.
6
8
10
12
36.2
53.6
60.9
76.8
92.8
108.8
2.40
3.02
3.65
4.28
70.5
87.2
1.43
2.11
2.78
3.43
16 141.1 5.56 120.2 4.73
Minimum B-dimension
Wearstrip distance A
A
B
Placement of Wearstrips and Sprockets
ST
AN
DA
RD
ST
AN
DA
RD
92
uni CPB
Width of sprockets: 10 - 12 teeth: 42.3 mm (1.67 in.)16 teeth: 40.8 mm (1.61 in.)
uni CPB Bi-directional Sprocket
Standard Bi-directional Sprockets
in.in. mmmmin.mmin.mm
Hub diameterOverall diameterpitch diameterNo. ofteeth
2.5665.0
4.72120.0
6.53165.86.47164.410
1833MPB10NR2
1833MPB10NR215INSQ
1833MPB10NR240MMSQ
1833MPB10NBBR2
1833MPB10NBBR260MMSQ
ø0.71/1.57*ø18.0/40.0*
sq 1.50sq 38.1
sq 1.57sq 40.0
ø1.57/2.76*ø40.0/ø70*
sq 2.36sq 60.0
1833MPB10NBBR225INSQsq 2.50sq 63.5
Reference no. plastic
Bore
4.72120.07.82198.67.73196.312 1833MPB12NBBR260MMSQsq 2.36sq 60.0
4.72120.010.04255.010.25260.4161833MPB16NBBR260MMSQ
1833MPB16NBBR290MMSQ
sq 2.36sq 60.0
sq 3.54sq 90.0
PA6 N
Other sprocket sizes are available upon request.
Please contact uni-chains® for further information.
Standard Material and Color
* Minimum/maximum round bore.
93
uni MPB
uni MPB – the most cleanable modular plastic belt in the world The uni MPB belt is the most cleanable, 2 in. pitch, straight running modular plastic belt in the world and the belt holdsthe most current NSF/USDA acceptance. The belt is used in various food applications and offers various styles from closed and open surfaces to roller or rubber top.
The uni MPB belt is the preferred belt in the following industries/applications:- Meat (beef & pork) applications including deboning lines, fat/trim lines, cutting lines, offal lines, evisceration lines,
Packaging lines and elevator/incline conveyors- Poultry applications including cage dumper lines, deboning lines, fat/trim lines, offal lines, grading lines, packaging
lines and elevator/incline conveyors- Fruit & vegetable applications including elevators, steam peeler lines, inspection tables, blanchers and packaging lines- Seafood applications including bulk feeder, elevators, inspection tables, grading lines, glazing lines, cooling and
freezing lines- Snack food applications including fryer discharge and incline applications
Product features and operational benefits:- Easy to clean Single Link® belt reduces downtime for cleaning up to 70%- Single Link® belt (no brick lay) reduces bacteria growth and Single Link® belt eliminates knives sticking in belt seams- Unique locking system (lockpin) – faster, simpler maintenance- Unique sprocket engagement – higher product load and longer conveyors- Strong and thick product supports allow more load without breakage- Stick and non stick surfaces allow optimized product throughput- Easy to clean roller top for long crate/box conveyors
Pitch 50.8 mm (2.00 in.)
ST
AN
DA
RD
94
uni MPB
uni MPB C uni MPB-N*
uni MPB 22%
uni MPB-G*
uni MPB 20%
uni MPB PRR
uni MPB 18%
uni MPB G/GE
uni MPB RO
uni MPB C, 18%, 20%, 22% uni MPB N/NE
uni MPB PRR
L
P
S
E
8.0
50.8
2.0
8.3
mm
0.31
N 3.0 0.12
2.00
R 3.2 0.13
0.08
T 16.0 0.63
V 15.3 0.60
X 3.5 0.14
0.33
in.
Standard Selection
Dimensional Sketches
uni MPB RO
W WPP PE
SS304
Dimensions
50.8 mm (2.00 in.)
Straight running
See page 101
Accessories
See page 101
See page 100
See page 7, 8 and 9Materials
65 mm (2.6 in.)With sideguard: 200 mm (7.9 in.)
See page 98 and 99
Alternative
uni MPB Rubber Top Type RB4
N01 See page 11
P
E L
T
T
Travel
P
R
E L
T
Travel Travel
P
S
E L
T
Travel Travel
E
L
N
N
E L
T
V
uni MPB Rubber Top
Travel
E L
T
P P P
X
Patent Patented
ST
AN
DA
RD
See page 129
* Indent: uni MPB-GE and uni MPB-NE are 35.0 mm (1.38 in.).
95
ST
AN
DA
RD
uni MPB
TypeStandard materials
and colors
Pin
Materials and colors
WPP
Standard Materials and Colors
uni MPB C
B
WPP
WPP
WPE
WPP
PP
WPEBPE-I
WPP
uni MPB 18% WPP
WPPW
WPE
uni MPB 20%
WPE
PP
NPE-I
N
WPOM-DI
NPE-I
NPE-I WPE
WPP
uni MPB 22% WPENPE-I
WPEBPE-I
WPPPP
uni MPB PRR* PP
uni MPB RO** NPA6.6
WPP
GPOM-DI
uni MPB Rubber Top NPA6.6WPOM-DI
WPOM-DIBaselink:
WPOM-DIRoller bed:
BPOM-DIRollers:
WPA6.6Rollers:
SS304Roller pins:
W
WPOM-DI
uni MPB-G/GE
uni MPB-N/NE
WPOM-DI
PE-I
** Standard materials foruni MPB RO
* Standard materials foruni MPB PRR
WPOM-DI
WPPBPOM-DI
W
WPOM-DI N
mm
151
184
268
302
335
402
418
452
637
653
5.9
7.2
10.6
11.9
13.2
15.8
16.5
17.8
25.1
25.7
mm
704
720
754
787
804
854
1022
1055
1089
1106
27.7
28.3
29.7
31.0
31.7
33.6
40.2
41.5
42.9
43.5
mm
1156
1173
1206
1240
1407
1457
1474
1507
1541
1558
45.5
46.2
47.5
48.8
55.4
57.4
58.0
59.3
60.7
61.3
mm
1608
1625
1809
1842
1859
1909
1926
1960
1993
2010
mm
63.3
64.0
71.2
72.5
73.2
75.2
75.8
77.2
78.5
79.1
486 19.1 871 34.3 1256 49.4 1658 206065.3 81.1
503 19.8 905 35.6 1307 51.5 1692 207766.6 81.8
553 21.8 938 36.9 1323 52.1 1709 211067.3 83.1
569 22.4 955 37.6 1357 53.4 1759 214469.3 84.4
603 23.7 1005 39.6 1390 54.7 1776 216169.9 85.1
2211
2228
2261
2295
2312
2362
2379
2412
2446
2462
2512
-
-
in.
87.0
87.7
89.0
90.4
91.0
93.0
93.7
95.0
96.3
96.9
98.9
-
-
in. in. in. mm in. in.
Standard Bricklayed Belt Widths (See next page for Single Link® widths)
N01+
PA6.6
ST
AN
DA
RD
96
uni MPB
K275 (67.0 mm (2.64 in.))
K325 (83.8 mm (3.30 in.))
K600 (151.0 mm (5.94 in.))
K725 (184.0 mm (7.24 in.))
K1800 (452.0 mm (17.80 in.))
K2000 (503.0 mm (19.80 in.))
K2400 (603 mm (23.74 in.))
uni MPB Single Link®
uni MPB is available as Single Link® in the following standard widths:
X
Belt type and widthsK275
67.0 mm (2.64 in.)
uni MPB C
uni MPB 18%
uni MPB 20%
uni MPB 22%
uni MPB-G/GE
X
X
uni MPB-N/NE
uni MPB PRR
uni MPB RO
X
K32583.8 mm(3.30 in.)
X
X
X
K600 151.0 mm (5.94 in.)
X
X
X
X
X
X
X
X
K725184.0 mm(7.24 in.)
X
X
X
X
X
K1800 452.0 mm(17.80 in.)
X
K2000503.0 mm (19.80 in.)
X
K2400603.0 mm(23.74 in.)
uni MPB Rubber Top X
uni MPB Single Link® Belt Widths
188427500
N/m
uni MPB C, 18%, 20% 22%, G/GE, N/NE, Rubber Top
75411000uni MPB RO
POM-DI
109616000
N/m
--
PP
89113000
N/m
--
188427500uni MPB PRR -- --
PE
Permissible Tensile Strength
lb/ft lb/ft lb/ft
Belt material
97
N
uni MPB RO
uni MPB PRR
4952200
4502000
N
23100
68300
Max. Load per Roller
lb
Max. permissible static loadMax. permissible dynamic
load (accumulation)
lb
uni MPB
10.8uni MPB 22%
11.3uni MPB RO
9.3uni MPB PRR*
11.2uni MPB 20%
11.1uni MPB 18%
11.9uni MPBC, G, GE, N, NE and Rubber Top
POM
1.477.2
--
--
1.527.4
1.547.5
1.708.3
PP
1.567.6
--
--
1.627.9
1.648.0
1.808.8
PE
kg/m2 kg/m2 kg/m2
2.44
2.27
2.29
2.21
2.31
1.91
* For total belt weights add 0.011 kg (0.024 lb) x no. of roller kits.
Belt Weights
plasticPin material
lb/ft2
plastic
lb/ft2
plastic
Belt material
lb/ft2
ST
AN
DA
RD
ST
AN
DA
RD
98
uni MPB with snub roller
uni MPB without snub roller
Max. Load per Sprocket
uni MPB
uni MPB Sprocket
PA6 N
Width of sprockets: 42.3 mm (1.67 in.)Tooth width: 9.5 mm (0.37 in.)
N lb
1250 281
2000 450
Other sprocket sizes are available upon request. Two-part sprocketsavaialable upon request.
Please contact uni-chains® for further information.
Please note, if travel is in both directions, an extra set of sprockets isrequired or use Bi-directional options. (See next page.)
Standard Material and Color
No. of
teethmm in. mm in.
6
8
10
12
36.2
53.6
59.5
75.1
91.0
107.0
2.34
2.96
3.58
4.21
70.5
87.2
1.43
2.11
2.78
3.43
16 139.2 5.48 120.2 4.73
Minimum B-dimension
Wearstrip distance A
A
B
Placement of Wearstrips and Sprockets
Standard Sprockets
* Minimum/maximum round bore.
2.5665.03.9299.54.00101.66
1833MPB06N
1833MPB06N15INSQ
1833MPB06N40MMSQ
in.in. mmmmin.mmin.mm
Hub diameterOverall diameterPitch diameterNo. ofteeth
ø0.71/1.57*ø18.0/40.0*
sq 1.50sq 38.1
sq 1.57sq 40.0
2.5665.05.23132.95.23132.88
1833MPB08N
1833MPB08N15INSQ
1833MPB08N20INSQ
ø0.71/1.57*ø18.0/40.0*
sq 1.50sq 38.1
1833MPB08N40MMSQsq 1.57sq 40.0
sq 2.00sq 50.8
2.5665.0
4.72120.0
6.53165.86.47164.410
1833MPB10N
1833MPB10N15INSQ
1833MPB10NBB
1833MPB10NBB25INSQ
ø0.71/1.57*ø18.0/40.0*
sq 1.50sq 38.1
ø1.57/2.76*ø40.0/ø70.0*
1833MPB10NBB20INSQsq 2.00sq 50.8
sq 2.50sq 63.5
1833MPB10NBB60MMSQsq 2.36sq 60.0
Reference no. plastic
Bore
2.5665.0
4.72120.0
7.82198.67.73196.312
1833MPB12N15INSQ
1833MPB12N40MMSQ
1833MPB12NBB
sq 1.50sq 38.1
sq 1.57sq 40.0
1.57/2.76*ø40.0/ø70.0*
1833MPB12NBB20INSQsq 2.00sq 50.8
1833MPB12NBB40MMSQsq 1.57sq 40.0
1833MPB12NBB60MMSQsq 2.36sq 60.0
2.8372.0
5.91150.010.04255.010.25260.416
1833MPB16N
1833MPB16NBB
ø0.71/1.57*ø18.0/40.0*
1.57/2.76*ø40.0/ø70.0*
1833MPB10N40MMSQsq 1.57sq 40.0
1833MPB12Nø0.71/1.57*ø18.0/40.0*
99
uni MPB
Standard Bi-directional Sprockets
in.in. mmmmin.mmin.mm
Hub diameterOverall diameterPitch diameterNo. ofteeth
2.5665.0
4.72120.0
6.53165.86.47164.410
1833MPB10NR2
1833MPB10NR215INSQ
1833MPB10NR240MMSQ
1833MPB10NBBR2
1833MPB10NBBR260MMSQ
ø0.71/1.57*ø18.0/40.0*
sq 1.50sq 38.1
sq 1.57sq 40.0
ø1.57/2.76*ø40.0/ø70*
sq 2.36sq 60.0
1833MPB10NBBR225INSQsq 2.50sq 63.5
Reference no. plastic
Bore
4.72120.07.82198.67.73196.312 1833MPB12NBBR260MMSQsq 2.36sq 60.0
4.72120.010.04255.010.25260.4161833MPB16NBBR260MMSQ
1833MPB16NBBR290MMSQ
sq 2.36sq 60.0
sq 3.54sq 90.0
* Minimum/maximum round bore.
Width of sprockets: 10 - 12 teeth: 42.3 mm (1.67 in.)16 teeth: 40.8 mm (1.61 in.)
uni MPBBi-directional Sprocket
PA6 N
Other sprocket sizes are available upon request.
Please contact uni-chains® for further information.
Standard Material and Color
ST
AN
DA
RD
ST
AN
DA
RD
100
uni MPB
uni MPB Product SupportFlat
uni MPB No Cling ProductSupport with drain
uni MPB Bent Product Support
uni MPB CuppedProduct Support
uni MPB MicroProduct Support M-types
uni MPB Micro Product Support 22%
uni MPB No Cling Product Support NC-types
Height
mm in.Style
K600 151.0
Standard materials & colors
POM-D PE-I
1.00
Flat
25.4
PP-IType mm in.
B2.0050.8
3.0076.2
4.00101.6
W
BW
B
BW
W
BW
6.00152.4 W W
N
N
N
B
NB
B
B
NC withdrain
NC
Bent
M-types 22%
K600 151.0
2.0050.8
5.943.0076.2
4.00101.6
3.0076.2
4.00101.6
3.0076.2
4.00101.6
6.00152.4
B
W
W
BW
NB
NB
B
K600
K600
151.0 5.94
151.0 5.94
K600 151.0 5.94
N
N
NB
B
W
W
4.00101.6
W
W
W
0.123.0
7.3
8.2
9.1
10.0
10.0
8.7
Cupped K600 151.0 5.9452.0
9.6
9.2
3.0
0.29
0.32
0.36
0.39
0.39
0.34
9.6 0.38
10.5 0.41
2.05
0.38
10.5 0.41
0.36
0.12
0.3910.0 WN
N
W BW
W5.94
B
mm in.
B
B
Standard Materials, colors and dimensions
Dimensional Sketches
B Width
M-types 3.0 0.12 K600 151.0 5.940.205.0 N
uni MPB Cuppeduni MPB M-types,
M-types 22%uni MPB Flat, Bent,NC, NC with drain
BW
Standard Selection Accessories
* Minimum bricklaid indent for uni MPB product support is 34.0 mm (1.34 in.).Increment: 16.8 mm (0.66 in.).
Note: For indent of 34 mm (1.34 in.) avoid using PP or PElockpin, always use PA6.6 lockpinor use an alternative pin retainingsystem.
Note: Depending on height and spacing the use of product supportsmay influence the backflex radius.
101
uni MPB
uni MPB Tab
Dimensions
G
J
K H
Travel
uni MPB Side Guard
CB
A
D D
E EP
Travel
Tra
vel
H
K
G
22.0
17.0
4.2
mm
0.87
J 23.2 0.91
0.67
0.17
in.
B
D
A
76.4
32.0
101.7
mm
3.00
C 50.9 2.00
1.26
E* 16.0 0.63
P 50.8 2.00
4.00
in.
WPOM-DI
Height
mm in.
Standard materials & colors
PE-I PP-I
2.0050.8
3.0076.2
4.00101.6
B
W
N WB
Note: Backflex radius when side guards are used: 200 mm (7.9 in.).
Dimensions
Standard Material and Color
Standard Materials, Colors and Dimensions
Note: When using a belt system with tabs, the temperature should be constant. Please note that the tabs are not always placed in the middle of the belt.
B
Standard Selection Accessories
Standard Selection Accessories
* 34.0 mm (1.34 in.) combined withproduct support.
Increment: 8.4 mm (0.33 in.).
Note: Side guards can not be positioned on top of G and N cones.
Note: When using tabs please verifythat sufficient clearance to the shaftexists.Max. shaft diameter = Sprocketpitch diameter - 63.5 mm (2.50 in.).When using square shafts verify that the diagonal does not exceedabove max. diameter.Example: Sprocket z = 6: Max. shaft diameter 100.0 - 63.5 =ø36 mm (3.94 - 2.50 = ø1.4 in.).
ST
AN
DA
RD
ST
AN
DA
RD
102
uni X-MPB
uni X-MPB – the strongest hygienic belt for the food industryThe uni X-MPB is part of the cleanable uni MPB series used mainly in various food applications. The 2.5 in. pitch, straight running belt has the highest tensile strength and impact resistance among the food belts offered by uni-chains®.
The uni X-MPB belt has proved to be a better belt in several industries/applications:- Meat (beef & pork) applications including deboning lines, fat/trim lines, cutting lines, offal lines, evisceration
lines and elevator/incline conveyors- Poultry applications including cage dumper lines, deboning lines, fat/trim lines, offal lines and elevator/incline
conveyors- Fruit & vegetable applications including elevators and inspection tables
Product features and operational benefits:- Easy to clean – reduced downtime for cleaning- Unique locking system (lockpin) – faster, simpler maintenance- Unique sprocket engagement – higher product load and longer conveyors- FDA approved materials and USDA accepted construction- Strong and thick product supports allow more load without breakage- Impact resistance to withstand heavy objects falling onto the belt
Pitch 63.5 mm (2.50 in.)
New
103
uni X-MPB C
Standard Selection
uni X-MPB C
Dimensional Sketches
Travel
E
L
P
T 2.50 63.5 P
0.7519.1 T
0.40 10.1L
0.33 8.3 E
mm in.
Dimensions
TypeStandard materials
and colors
Pins
Materials and colors
Standard Materials and Colors
uni X-MPB C W
NPE-I
PE-I
NPA6.6
WPE
POM-DI NPA6.6
B
mm
75
151
226
302
377
453
528
3.0
5.9
8.9
11.9
14.9
17.8
20.8
mm
604
679
755
830
26.7
29.7
32.7
1358
1434
1509
1585
1660
53.5
56.4
59.4
62.4
65.4
2188
2264
2339
2415
86.2
89.1
92.1
95.1
906
981
1056
1132
120723.8
35.7
38.6
41.6
44.6
47.5
1283 50.5
mm mm
1736
1811
1887
1962
2037
68.3
71.3
74.3
77.2
80.2
2113 83.2
2792
2868
2943
3019
109.9
112.9
115.9
118.8
mm
2490
2566
2641
98.0
101.0
104.0
2717 107.0
Standard Bricklayed Belt Widths (See next page for Single Link® widths)
uni X-MPB
Patent Patent pending
Accessories
See page 104
See page 129
ST
AN
DA
RD
63.5 mm (2.50 in.)
Straight running
See page 105
75 mm (2.95 in.)
See page 7 and 8Materials
in. in. in. in. in.
Alternative
PP W
ST
AN
DA
RD
104
uni X-MPB
uni X-MPB Single Link®
uni X-MPB is available as Single Link® in the following standard widths:
K300 (75.3 mm (2.96 in.))
K600 (151.0 mm (5.94 in.))
uni X-MPB C
N/m
30000
PP
POM
2056
N/m
37500
PA6.6
2570
N/m
10000
PE
PE
685
uni X-MPB C
kg/m2
14.5
PP
POM
2.96
kg/m2
14.7
PA6.6
3.0
PE
PE
2.05
Pin material
Belt material
lb/ft lb/ft lb/ft
Permissible Tensile Strength
Belt Weights
Pin material
Belt material
lb/ft2 lb/ft2 lb/ft2kg/m2
10.0
Height
mm in.
Width
K600 151.0
Standard material & color
POM-DI
4.00101.6
Type mm in.
5.94
uni X-MPB Product Support uni X-MPB Product Support
Dimensional Sketch
Travel
Standard Materials, Colors and Dimensions
W
Standard Selection Accessories
105
Standard Bi-directional Sprockets for uni X-MPB
2.7670.04.89124.24.96126.06 8033XMPB06NR2
in.in. mmmmin.mmin.mm
Hub diameterOverall diameterPitch diameterNo. ofteeth
ø0.71/1.57*ø18.0/40.0*
2.7670.06.52165.66.48164.68 8033XMPB08NR2ø0.71/1.57*ø18.0/40.0*
8033XMPB10NBBR2ø1.57/2.76*ø40.0/70.0*8.13206.68.03203.910 4.72120.0
4.72120.0
2.7670.0 8033XMPB13NR2
8033XMPB13NBBR215INSQ
8033XMPB13NBBR225INSQ
ø0.71/1.57*ø18.0/40.0*
sq 1.50sq 38.1
sq 2.50sq 63.5
10.54267.810.44265.313
Reference no.Bore
uni X-MPB
Max. Load per Sprocket
uni X-MPB Sprocket
PA6 N
Width of sprockets: 42.3 mm (1.67 in.)Tooth width: 12.0 mm (0.47 in.)
N lb
2500 560
Other sprocket sizes are available upon request. Two-part sprockets available upon request.
Please contact uni-chains® for further information.
* Minimum/maximum round bore.
Standard Material and Color
uni X-MPB
No. of
teethmm in. mm in.
6
8
10
13
44.9
66.6
72.5
92.0
111.7
141.7
2.85
3.62
4.40
5.58
87.6
118.7
1.77
2.62
3.45
4.67
Minimum B-dimension
Wearstrip distance A
A
B
Placement of Wearstrips and Sprockets
ST
AN
DA
RD
ST
AN
DA
RD
106
uni XLB
uni XLB – the strongest belt in the “uni-verse”uni XLB 2.5 in. pitch, straight running belt was designed for heavy duty conveyors and to replace steel slat top chains,drag chains and other technologies being used for high wear or heavy duty applications.
The uni XLB (Closed Top, Rough Top and V-Shape) belts have increased performance in the followingindustries/applications:- Automotive applications including skid conveyors, manrider belts, car conveyors, leak tests- Carwash applications including carwash, interior detailing areas- Material handling applications including pallet handling, moving large paper rolls- Meat (beef & pork) applications including shackle tables, gam tables
Product features and operational benefits:- No lubrication required- Reduced horsepower due to low friction materials- Reduced downtime due to easy maintenance- Reduced noise level- Extremely wear and impact resistant- Unique sprocket engagement allows long conveyors with reduced pulsation- Rough top surface reduces slippage and allows safe movements
Pitch 63.5 mm (2.50 in.)
New
107
uni XLB
uni XLB C
uni XLB V4
uni XLB C Rough uni XLB 15% Rough
Standard Selection
uni XLB C
Dimensional Sketches
Travel
E
L
P
T
uni XLB C Rough
Travel
E
L
P
S
T
uni XLB 15% Rough
Travel
E
L
P
S
T
uni XLB V4 and V8
Travel
E
L
P
Z/Y
T
SS304
63.5 mm (2.50 in.)
Straight running
See page 109
100 mm (3.9 in.)
See page 7 and 8Materials
L
E
15.0
10.5
mm
0.59
0.41
in.
S
P
1.5
63.5
0.06
2.50
T 30.0 1.18
Z 4.0 0.16
Y 8.0 0.31
Dimensions
Alternative
mm
100
200
299
398
498
598
697
3.9
7.9
11.8
15.7
19.6
23.5
27.4
mm
797
896
996
1096
35.3
39.2
43.1
1793
1892
1992
2092
2191 70.6
74.5
78.4
82.3
86.3
2888
2988
3087
3187
113.7
117.6
121.5
125.51195
1295
1394
1494
159431.4 47.1
51.0
54.9
58.8
62.7
1693 66.7
mm mm
2291
2390
2490
2590
268990.2
94.1
98.0
102.0
105.9
2789 109.8
in. in. in. in. mm in. mm in. mm in. mm in.
Standard Bricklayed Belt Widths (See next page for Single Link® widths)
LocksType
Standard materials and colors
Pins
Materials and colors Materials and colors
Standard Materials and Colors
uni XLB C
uni XLB 15% Rough
D
D
NPA6.6
NPA6.6 PP
PP
KPOM-NLAS
uni XLB V4 and V8
KPOM-NL
uni XLB C Rough
KPOM-D DPP
DPPKPOM-NLAS NPA6.6
DPPKPOM-NLAS NPA6.6
Patent Patent pending
NPA6.6
SS304
See page 129
ST
AN
DA
RD
uni XLB V8
ST
AN
DA
RD
108
uni XLB
uni XLB
N/m
90000
PA6.6
POM
6210
N/m
100000
SS
6900
Pin material
Belt material
lb/ft lb/ft
Permissible Tensile Strength
uni XLB Single Link®
uni XLB is available as Single Link® in the following standard widths:
K318 (80.8 mm (3.18 in.))
K400 (99.8 mm (3.93 in.))
K800 (199.6 mm (7.86 in.))
uni XLB
kg/m2
31.0
PA6.6
POM
6.35
kg/m2
40.8
SS
8.36
uni XLB V4 and V8 33.9 6.94 42.3 8.66
Pin material
Belt material
lb/ft2 lb/ft2
Belt Weights
Belt type and widths K31880.8 mm (3.18 in.)
uni XLB
uni XLB C Rough
uni XLB 15% Rough
uni XLB V4 and V8
X
K40099.8 mm (3.93 in.)
X
X
X
K800 199.6 mm (7.86 in.)
X
X
X
uni XLB Single Link® Belt Widths
SLO
SLO = Single Link only
109
Standard Bi-directional Sprockets for uni XLB
4.72120.07.98202.68.09205.510
7333XLB10NR2
in.in. mmmmin.mmin.mm
Hub diameterOverall diameterPitch diameterNo. ofteeth
ø0.71/1.57*ø18.0/40.0*
7333XLB10NR215INSQsq 1.50sq 38.1
7333XLB10NR240MMSQsq 1.57sq 40.0
7333XLB10NBBR2ø0.71/1.57*ø18.0/40.0*
7333XLB10NBBR225INSQsq 2.50sq 63.5
7333XLB10NBBR220INSQsq 2.00sq 50.8
7333XLB10NBBR260MMSQsq 2.36sq 60.0
7333XLB10PNR225INSQsq 2.50sq 63.5
7333XLB10PNR240MMSQsq 1.57sq 40.0
7333XLB10PNR260MMSQsq 2.36sq 60.0
7333XLB10PNR290MMSQsq 3.54sq 90.0
--10.41264.410.44265.313 7333XLB13PNR2ø0.71/1.57*ø18.0/40.0*
--12.04305.912.02305.4157333XLB15PNR2ø0.71/1.57*ø18.0/40.0*
7333XLB15PNR225INSQsq 2.50sq 63.5
7333XLB20PNR215INSQsq 1.50sq 38.1
7333XLB20PNR220INSQsq 2.00sq 50.8
7333XLB20PNR225INSQsq 2.50sq 63.5
7333XLB20PNR240MMSQsq 1.57sq 40.0
7333XLB20PNR260MMSQsq 2.36sq 60.0
--16.03407.115.98405.920
Reference no. plastic
Bore
uni XLB
Max. Load per Sprocket
uni XLB Sprocket
PA6 N
Width of sprockets: 33.0 mm (1.30 in.)Tooth width: 16.0 mm (0.63 in.)
N lb
12000 2700
Other sprocket sizes are available upon request. Two-part sprockets available upon request.Please contact uni-chains® for further information.
* Minimum/maximum round bore.
Standard Material and Color
uni XLB
No. of
teethmm in. mm in.
10
13
15
82.7
113.8
117.7
147.7
168.0
4.63
5.81
6.61 134.7
3.26
4.48
5.30
20 218.0 8.58 185.5 7.30
Minimum B-dimension
Wearstrip distance A
A
B
Placement of Wearstrips and Sprockets
ST
AN
DA
RD
111
uni M-SNB M2
uni M-SNB M2
T
LE
P
Made-To-Order MaterialsPOM-D, PP and PE
Made-To-Order Bricklayed Belt Widths
76
152
228
304
381
456
533
608
685
762
3.0
6.0
9.0
12.0
15.0
18.0
21.0
23.9
27.0
30.0
837
914
990
1066
1142
1218
1294
1370
144633.0
59.936.0
62.939.0
65.942.0
68.945.0
71.948.0
50.9
53.9
56.9
1522
1598
1674
1750
1826
1902
1978
2054
2130
2206
2282
2358
2434
mm in. mm in. in.mm mm
74.9
77.9
80.9
83.9
86.9
89.8
92.8
95.8
in.
2510
2586
2662
2738
2814
2890
2966
3042
mm
98.8
101.8
104.8
107.8
110.8
113.8
116.8
119.8
in.
Surface opening 14%
uni M-SNB M2
Dimensional Sketch
Travel
L
T
E
4.4
8.8
5.1
mm
0.17
P 12.7 0.50
0.35
0.20
in.
Dimensions
Made-To-Order Selection
MA
DE
-TO
-OR
DE
R
BWPP
W WPP PE
SS304BNPA6.6
N01 See page 11
WPP
NPA6.6
12.7 mm (0.50 in.)
See page 7 and 8
Straight running
20 mm (0.8 in.)
See page 25
Materials
Patent Patented
See page 129
MA
DE
-TO
-OR
DE
R
112
uni Light CR uni Light 10% SR uni Light 18%
uni Light Vacuum uni Light Flat Rubber Top
Made-To-Order Selection
uni Light 18%, Vacuum
Dimensional Sketches
uni Light Rib
uni Light Rib
uni Light Rough Rubber Top
E
Travel
Travel
E
R
P
L
L
P
T
uni Light 10% SR
E
Travel
P
LT
uni Light Flat Rubber Top
E
Travel
P
LTT
uni Light Rough Rubber Top
Travel
E
A
L
P
T
B
DN
KN03
W WPP PE
SS304B
NGR
PA6.6
GW
NPA6.6
PP
See page 11
19.1 mm (0.75 in.)
See page 7, 8 and 9
Straight running
See page 29
Materials
25 mm (1.0 in.)uni Light Rib: 50 mm (2.0 in.)
See page 30
Accessories
See page 31
See page 30
See page 114
Made-To-Order Materials POM-D, POM-LF, PP, PE and PA6
B
A
B
A
3.0
2.0
mm
0.12
0.08
in.
L
E
4.3
5.1
mm
0.17
0.20
in
R
P
7.3
19.1
mm
0.29
0.75
in.
T
S
8.5
1.5
mm
0.33
0.06
in.
Dimensions
WPP
uni Light CR
Travel
E
S
L
P
T
Note: uni Light Flat Rubber anduni Light Rough Rubber areonly available in PP.
uni Light
Patent Patented
mm in. No. of holes
3.2 0.12 5
4.0 0.16 5
Total open area %
7.64
8.40
4.0 0.16 7 9.24
4.0 0.16 8 9.66
5.2 0.20 5 9.87
5.6 0.22 7 12.10
5.6 0.22 8 12.93
Dimensions for uni Light Vacuum
See page 129
113
uni Light
76
153
229
306
382
458
535
611
687
764
3.0
6.0
9.0
12.0
15.0
18.0
21.1
24.1
27.0
30.1
840
917
993
1070
1146
1223
1299
1375
1451
1528
33.1
36.1
39.1
42.1
45.1
48.1
51.1
54.1
57.1
60.2
1604
1681
1757
1834
1910
1987
2063
2139
2216
2292
63.1
66.2
69.2
72.2
75.2
78.2
81.2
84.2
87.2
90.2
2369
2445
2522
2598
2674
2751
2827
2904
2980
3057
93.3
96.3
99.3
102.3
105.3
108.3
111.3
114.3
117.3
120.4
mm in. mm in. mm in. mm in.
Made-To-Order Bricklayed Belt Widths
70210250uni Light
POM
3515125
PP
Permissible Tensile Strength
lb/ftN/m lb/ftN/m
2113075
--uni Light Rough Rubber Top 3515125 --
PE
lb/ftN/m
Belt material
1.396.8uni Light CR
POM
2.9114.2 0.984.8
PP
2.5012.2 1.004.9
PE
2.5412.4
1.276.2uni Light 10%SR 2.8113.7 0.884.3 2.4411.9 0.944.6 2.4812.1
1.889.2uni Light Rib 3.4416.8 1.296.3 2.8513.9 1.356.6 2.8914.1
1.336.5uni Light Vacuum 2.8714.0 0.904.4 2.4612.0 0.964.7 2.5012.2
1.135.5uni Light 18% 2.6613.0 0.803.9 2.3611.5 0.844.1 2.3811.6
--uni Light Flat Rubber Top -- 1.135.5 2.6613.0 -- --
Belt Weights
lb/ft2kg/m2
plasticPin material
lb/ft2kg/m2
steel
lb/ft2kg/m2
plastic
lb/ft2kg/m2
steel
lb/ft2kg/m2
plastic
lb/ft2kg/m2
steel
Belt material
MA
DE
-TO
-OR
DE
R
MA
DE
-TO
-OR
DE
R
114
uni Light Finger Plate Type 1A K300
A
B
C
D
EF
G
H
L
uni Light Finger Plate Type 2 K300
H
G
F E
M
O
N
A
uni Light Finger Plate Type 3 K300
EF
G
H
I
A
J
K
Dimensions
All uni-chains® belt systems that areavailable in a raised rib version canbe supplied with matching fingerplates, also called combs.
The finger plates are supplied withcover caps which can be attachedwhen the finger plate has beeninstalled. The cover caps can be re-moved by using a screwdriver thatcan be inserted between the coverand finger plate.
B
C
D
A
132.9
80.0
14.9
3.8
mm
5.23
3.15
0.59
E 75.4 2.97
F 40.0 1.57
G 12.0 0.47
H 10.0 0.39
I 197.1 7.76
J 90.3 3.56
K 40.0 1.57
L 54.5 2.15
M 98.9 3.89
N 20.0 0.79
O 45.2 1.78
0.15
in.
Made-To-Order Materials POM-LF, POM-DI and POM-EC
Made-To-Order Selection Accessories
uni Light
Snap-OnCover Caps
Snap-OnCover Caps
Snap-OnCover Caps
115
uni Flex SNB
uni Flex SNB with Rollersø17 x 5.5 mm (ø0.7 x 0.22 in.)
Made-To-Order Selection
Made-To-Order Materials POM-D, PP, PA6.6 and Roller Material POM-D
A min. 50.8
mm
2.00
in.
Dimensions
Height
mm in.Style
Width
43.00.16 Rubber Support4.0
mm in.
1.69
Length
14.0
mm in.
0.55
42.00.16 Product Support low4.0 1.65 10.5 0.41
25.4 mm (1.00 in.)
Side flexing
See page 54
50 mm (2.0 in.)
See page 7, 8 and 10Materials
SS316
BNPA6.6 W
W
PP
PE
Dimensions
Made-To-Order Materials Roller: POM-D and Rubber 01N
Rubber Support•
• Product Support low
Made-To-Order Selection Accessories
SS304
A
Roller ø17 x 17 mm (ø0.7 x 0.7 in.)
Roller ø17 x 30 mm (ø0.7 x 1.2 in.)
Rollers are available in widths: 5.5, 17 and 30 mm (0.23, 0.7 and 1.2 in.).
Patent Patented
See page 129
MA
DE
-TO
-OR
DE
R
MA
DE
-TO
-OR
DE
R
116
D
GWBPP
W WPP PE
BPA6.6
NPA6.6
SS304
25.4 mm (1.00 in.)
See page 7, 8 and 9
Straight running
See page 61
Materials
30 mm (1.2 in.)
See page 59
Accessories
See page 60
uni SNB M2 with Rollers
Made-To-Order Selection
Product Support
Product Support
Dimensional Sketches
Travel
Height
mm in.
Width
K300 75.91.0025.4
2.0050.8
3.0076.2
Type in.mm in.
2.99
K300 75.9 2.99
K300 75.9 2.99
Dimensions
Made-To-Order Materials POM-D, PP and PE
Made-To-Order Selection Accessories
A
Roller ø12 x 5.5 mm (ø0.5 x 0.2 in.)
Made-To-Order Materials POM-D, PP, PE and Roller Material POM-D
A min. 50.8
mm
2.00
in.
Dimensions
uni SNB M2
Patent Patented
* Only for uni SNB M2 34% and uni SNB M2 34% Rib. Not 20%-style belts.
*
*
See page 129
117
uni Light EP
B
W WPP PE
BPA6.6 SS304
GWPP
WPP
38.1 mm (1.50 in.)
Straight running
See page 76
See page 119
Accessories
See page 120
See page 119
See page 121
See page 75
75 mm (3.0 in.)uni Light EP Rib:150 mm (5.9 in.)
Materials See page 7 and 8uni Light EP C uni Light EP 22%uni Light EP 8.5%
uni Light EP 46% uni Light EP 18%
uni Light EP 33%
uni Light EP Vacuum
uni Light EP Rib C uni Light EP Rib 33%
uni Light EP 28%
Made-To-Order Selection
uni Light EP
Dimensional Sketches
E
Travel
P
L
T
uni Light EP Rib C, Rib 33%
E
Travel
P
L
T
L
E
4.3
5.1
mm
0.17
0.20
in.
R
P
7.3
38.1
mm
0.29
1.50
in
-
T
-
8.5
mm
-
0.34
in.
Dimensions
R
Made-To-Order Materials POM-D, POM-LF, PP and PE
Patent Patented
See page 129
MA
DE
-TO
-OR
DE
R
MA
DE
-TO
-OR
DE
R
118
uni Light EP
mm
102
152
254
305
355
406
458
509
559
610
4.0
6.0
10.0
12.0
14.0
16.0
18.0
20.0
22.0
24.0
mm
661
712
763
814
865
916
966
1017
1068
1119
26.0
28.0
30.0
32.0
34.0
36.0
38.0
40.0
42.0
44.0
mm
1170
1220
1271
1832
1373
1424
1474
1525
1576
1627
46.0
48.0
50.0
52.0
54.0
56.0
58.0
60.0
62.0
64.0
mm
1678
1728
1779
1830
1881
1932
1982
2033
2084
2135
66.0
68.0
70.0
72.0
74.0
76.0
78.0
80.0
82.0
84.0
mm
2186
2236
2287
2338
2389
2440
-
-
-
-
86.0
88.0
90.0
92.0
94.0
96.0
-
-
-
-
in. in. in. in. in.
Made-To-Order Bricklayed Belt Widths
70210250uni Light EP
N/m
POM
3515125
N/m
PP PE
2113075
N/m
Permissible Tensile Strength
lb/ft lb/ft lb/ft
Belt material
kg/m2
POM
1.165.7uni Light EP C/8.5%/vacuum
kg/m2
1.909.3
kg/m2
PP
0.763.7
kg/m2
1.507.3
kg/m2
PE
0.824.0
kg/m2
1.567.6
0.984.8uni Light EP 18%/28% 1.728.4 0.703.4 1.437.0 0.743.6 1.487.2
0.904.4uni Light EP 33%/46% 1.648.0 0.633.1 1.376.7 0.683.3 1.416.9
1.457.1uni Light EP Rib 2.1910.7 0.944.6 1.688.2 1.005.0 1.768.6
Belt Weights
lb/ft2
plasticPin material
lb/ft2
steel
lb/ft2
plastic
lb/ft2
steel
lb/ft2
plastic
lb/ft2
steel
Belt material
119
uni Light EP
uni Light EP Tab
Dimensions
H
K
G
15.9
11.9
3.5
mm
0.63
J 26.0 1.02
0.47
0.14
in.
POM-D
Made-To-Order Material
K H
JG
Travel
Note: In belt systems with tabs the temperature of the conveyor should be constant.Please note that the tabs are not always placed in the middle of the belt.
uni Light EP Side Guard
B
P
A
15.0
38.1
31.7
mm
0.59
C 23.0 0.91
1.50
1.25
in.
Dimensions
A
P
Travel
B B
C C
Tra
vel
POM-D
Made-To-Order Material
Made-To-Order Selection Accessories
Made-To-Order Selection Accessories
Note: When using tabs please verifythat sufficient clearance to the shaftexists.Max. shaft diameter = Sprocketpitch diameter - 44.5 mm (1.75 in.).When using square shafts verify that the diagonal does not exceedabove max. diameter.Example: Sprocket z = 7: Max. shaft diameter 87.8 - 44.5 =ø43 mm (3.46 - 1.75 = ø1.7 in.).
Increment: 6.5 mm (0.26 in.).
MA
DE
-TO
-OR
DE
R
MA
DE
-TO
-OR
DE
R
120
uni Light EP
uni Light EP Product Support flat (no Ribs) uni Light EP Product Support with Ribs
uni Light EPProduct Support flat (no Ribs)
Dimensional Sketches
Travel
uni Light EPProduct Support with Ribs
Travel
Height
mm in.Style
Width
K750 191.0 7.52
101.6
152.8
4.00
6.02
K400
K600
Indent left/right
1.00
flat
with ribs25.4
flat
no
no
no
17.5 0.69
Type mm in. mm in.
101.6
152.8
4.00
6.02
K400
K600with ribs
2.0050.8
no
no
191.0 191.0K750
152.8 6.02K600with ribs3.0076.2 no
Dimensions
POM-D, PP-I and PE
Made-To-Order Materials
Made-To-Order Selection Accessories
* Minimum bricklaid indent for uni Light EP product support is 38.1 mm (1.50 in.).Increment: 12.7 mm (0.50 in.).
121
uni Light EP
uni Light EP Finger Plate Type 2
Dimensions
All uni-chains® belt systems that areavailable in a raised rib version canbe supplied with matching fingerplates, also called combs.
The finger plates are supplied withcover caps which can be attachedwhen the finger plate has beeninstalled. The cover caps can be re-moved by using a screwdriver thatcan be inserted between the coverand finger plate.
E
F
G
A
152.4
101.6
12.0
3.3
mm
6.00
4.00
0.47
H 10.3 0.41
M 135.0 5.31
N 23.0 0.91
O 57.0 2.24
0.13
in.
EG
H
N
O
M
A
F
Made-To-Order MaterialPOM-LF
Made-To-Order Selection Accessories
MA
DE
-TO
-OR
DE
R
Snap-OnCover Caps
MA
DE
-TO
-OR
DE
R
122
uni SSB
uni SSB Rubber Top
Made-To-Order Selection
BPP
NGR
I05
SS304
Materials
38.1 mm (1.50 in.)
See page 7 and 8
Straight running
45 mm (1.8 in.)
See page 11
uni SSB Rubber Top
Dimensional Sketches
E
Travel
P
LT B
E
P
B
6.5
38.1
2.5
mm
0.26
L 6.4 0.25
1.50
T 12.7 0.50
0.10
in.
Dimensions
Made-To-Order MaterialsPOM-SLF, POM-LF and GR
mm
76
152
228
304
380
456
532
607
683
759
3.0
6.0
9.0
12.0
15.0
18.0
20.9
23.9
26.9
29.9
mm
835
911
987
1063
1139
1216
1291
1367
1443
1519
32.9
35.9
38.9
41.9
44.9
47.9
50.8
53.8
56.8
59.8
mm
1595
1671
1747
1823
1899
1975
2051
2127
2203
2279
62.8
65.8
68.8
71.8
74.8
77.8
80.8
83.7
86.7
89.7
mm
2355
2431
2507
2583
2659
2735
2811
2887
2963
3039
92.7
95.7
98.7
101.7
104.7
107.7
110.7
113.7
116.6
119.6
in. in. in. in.
Made-To-Order Bricklayed Belt Widths
2.5412.4uni SSB Rubber Top
kg/m2
GR
POM
2.5012.2
kg/m2
PP
3.0715.0
kg/m2lb/ft2
Pin material
lb/ft2 lb/ft2
steel
Belt material
Belt Weights
See page 72
See page 72
See page 129
123
mm
151
185
268
302
335
386
403
418
452
486
in.
5.9
7.3
10.6
11.9
13.2
15.2
15.9
16.5
17.8
19.1
mm
503
536
570
603
636
703
754
788
804
872
in.
32.9
35.9
38.8
41.8
44.8
47.8
50.8
53.8
56.8
59.8
mm
905
938
988
1022
1055
1206
1357
1508
1659
1810
in.
35.6
36.9
38.9
40.2
41.5
47.5
53.4
59.4
65.3
71.2
mm
1960
2111
2262
2413
2564
2714
2865
3016
3167
3318
in. mm in.
77.2
83.1
89.1
95.0
100.9
106.9
112.8
118.7
124.7
130.6
Made-To-Order Bricklayed Belt Widths
uni OPB
uni OPB-C
Made-To-Order Selection
uni OPB Rough uni OPB 20%
uni OPB 25%
uni OPB Rubber Top Type RB2
uni OPB Vacuum
uni OPB Rubber Top Type RB3
uni OPB Rubber Top Type RB1
KN03
B
W WPP PE
SS304
GWPP
BWPE
WPP
50.0 mm (1.97 in.)
See page 7, 8, 9 and 10
Straight running
Materials
75 mm (3.0 in.)Rib: 300 mm (11.8 in.)Side guards: 200 mm (7.9 in.)
See page 125
Accessories
See page 126
See page 86
See page 127
See page 85
POM-D, POM-LF, POM-SLF, PP, PE, PA6.6 and PA6.6H
Made-To-Order Materials
WPP
Patent Patented
See page 11
See page 129
MA
DE
-TO
-OR
DE
R
MA
DE
-TO
-OR
DE
R
124
uni OPB
L
E
8.0
8.3
mm
0.31
0.33
in.
P 50.0
mm
1.97
in
T
S
4.0
7.8
mm
0.16
0.31
in.
X
V
2.5
16.0
mm
0.10
0.63
in.
Z 2.0 0.08
uni OPB 4V
Dimensional SketchesTravel*
V
EL
P
Bottom uni OPB 4V uni OPB 4
Travel
V
EL
P
T
Bottom uni OPB 4
uni OPB 8M
Travel
V
EL
P
S
uni OPB 8
Travel
E
P
SLV
uni OPB Rubber Top RB1
Travel*
V
EL
P
uni OPB Rubber Top RB2
Travel*
V
EL
P
Z
uni OPB Rubber Top RB3
Travel
P
Z
L
V
X
E
Tra
vel
Bottom uni OPB 8
Tra
vel
Tra
vel
uni OPB 8P
Travel
E
P
SLV
Bottom uni OPB 8P
Tra
vel
Bottom uni OPB 8M
Tra
vel
uni OPB C
uni OPB C Rough
uni OPB 20%
X*
uni OPB 4Bottom
Top
uni OPB 25%
uni OPB Vacuum X
X
uni OPB 8M
X*
X
uni OPB 4V
X
X*
X
X
uni OPB 8
X*
X
uni OPB 8P
Combinations of Top and Bottom Surface
* Note: These types are listed in the USDA "Accepted Meat and Poultry Equipment" publication as accepted for foodcontact.
Dimensions
* uni-chains® recom-mends this travel direc-tion. However, travel inboth directions is possi-ble.
125
uni OPB
uni OPB Tab
Dimensions
H
K
G
22.0
17.0
4.2
mm
0.87
J 23.2 0.92
0.67
0.17
in.
POM-D, POM-LF and PP
Made-To-Order Material
G
J
K H
Travel
150722000uni OPB 4V/8
POM
75411000
PP
4526600
75411000uni OPB 4 3775500 2263300
6108900uni OPB 8P/8M 6108900 4526600
PE
Permissible Tensile Strength
lb/ftN/m lb/ftN/m lb/ftN/m
Belt material
2.0710.1uni OPB 20%/25%
2.4011.7uni OPB C/C Rough/Vac.
POM
3.3016.1
3.7518.3
1.416.9
1.547.5
PP
2.7413.4
2.8714.0
1.507.3
1.668.1
PE
2.8313.8
2.9914.6
Belt Weights
lb/ft2kg/m2
plastic steelPin material
lb/ft2kg/m2 lb/ft2kg/m2
plastic steel
lb/ft2kg/m2 lb/ft2kg/m2
plastic steel
lb/ft2kg/m2
Belt material
Made-To-Order Selection Accessories
Note: When using a belt system with tabs, the temperature should be constant. Please note that the tabs are not always placed in the middle of the belt.
Note: When using tabs please verify that sufficient clearance to the shaft exists.Max. shaft diameter = Sprocket pitch diameter - 63.5 mm (2.50 in.).When using square shafts verify that the diagonal does not exceed above max. diameter.Example: Sprocket z = 6: Max. shaft diameter 100.0 - 63.5 = ø36 mm (3.94 - 2.50 = ø1.4 in.).
MA
DE
-TO
-OR
DE
R
MA
DE
-TO
-OR
DE
R
126
uni OPB
uni OPB Product Support NoCling and flat
Dimensional Sketches
uni OPB Product Support No Cling with Ribs
TravelTravel
Height
mm in.Style
Width
Type mm in.
K600 151.0 5.94OPB 4 PS No Cling
OPB 4 PS No Cling with Ribs
2.0050.8
3.0076.2
4.00101.6
2.0050.8
3.0076.2
4.00101.6
K600 151.0 5.94
OPB 4V-23F PS No Cling 2.0050.8
3.0076.2K600 151.0 5.94
OPB 8, OPB 8P and OPB 8M PS No Cling
2.0050.8
3.0076.2
4.00101.6
6.00152.4
K600 151.0 5.94
OPB 8, OPB 8P and OPB 8M PS No Cling with Ribs
2.0050.8
3.0076.2
4.00101.6
K600 151.0 5.94
Dimensions
PPHW
Made-To-Order Material
Made-To-Order Selection Accessories
* Minimum bricklaid indent for uni OPB product support is 21.0 mm (0.83 in.).Increment: 8.4 mm (0.33 in.).
uni OPB Product Support flat
OPB 8 PS flat
2.0050.8OPB 4V-23F PS No Cling with Ribs K600 151.0 5.94
K600 151.0 5.94
uni OPB Product Support No Cling uni OPB Product Support No Cling with Ribs
127
uni OPB
uni OPB Finger Plate Type 3
Dimensions
All uni-chains® belt systems that areavailable in a raised rib version canbe supplied with matching fingerplates, also called combs.
The finger plates are supplied withcover caps which can be attachedwhen the finger plate has beeninstalled. The cover caps can be re-moved by using a screwdriver thatcan be inserted between the coverand finger plate.
E
F
G
A
149.0
100.0
12.0
2.8
mm
5.87
3.94
0.47
H 9.0 0.35
I 259.0 10.20
J 120.0 4.72
K 60.0 2.36
0.11
in.
Made-To-Order MaterialPOM-LF
Made-To-Order Selection Accessories
H
F E
I
J
K
A
G
MA
DE
-TO
-OR
DE
R
Snap-OnCover Caps
128
uni CPB with Thread Insertsuni CPB 20% Rough with Thread Inserts
Made-To-Order Selection
NPA6.6
50.8 mm (2.00 in.)
Straight running
See page 91 and 92
85 mm (3.3 in.)
See page 7 and 8Materials
mm
150
200
250
300
350
401
451
5.9
7.9
9.8
11.8
13.8
15.8
17.8
mm
501
551
601
651
701
751
21.7
23.7
25.6
27.6
29.6
1201
1252
1302
1352
1402
47.3
49.3
51.3
53.2
55.2
1852
1902
1952
2002
72.9
74.9
76.9
78.8
2052
2102
80.8
82.8
801
851
901
951
100119.7
31.5
33.5
35.5
37.4
39.4
1051 41.4
1101 43.3
1151 45.3
mm
1452
1502
1552
1602
1652
1702
1752
57.2
59.1
61.1
63.1
65.0
67.0
69.0
1802 70.9
in. in. in.
Made-To-Order Bricklayed Belt Widths in.
Made-To-Order MaterialsPOM-NLAS, POM-NL
The thread inserts allow for easy attachment of fixtures to the belt.
Available insert size M5.
Depending on the size and shape of the attachment, attention should be payed tohow it will influence the backflex radius of the belt.
uni CPB
mm
See page 129
MA
DE
-TO
-OR
DE
R
129
* Use sprocket sizes that ensure that belt or chain does not conflict with uni Retainer Rings™
uni Retainer Rings™
D
ø20
ø25
ø30
ø40
ø50
40 x 40 mm
39
44
50
1.5
1.7
2.0
63 2.5
75 3.0
63 2.5
B
mm in.
50 x 50 mm
60 x 60 mm
ø1”
ø1.5”
ø2”
1” x 1”
80
95
44
3.1
3.7
1.7
63 2.5
75 3.0
44 1.7
14
14
16
18
18
18
C
mm
18
18
14
18
18
14
1.5” x 1.5”
2.5” x 2.5”
63 2.5
95 3.7
18
18
0.6
0.6
0.6
0.7
0.7
0.7
in.
0.7
0.7
0.6
0.7
0.7
0.6
0.7
0.7
ø39
ø44
ø50
ø63
ø75
ø80
A*
mm
ø103
ø124
ø44
ø63
ø75
ø52
ø80
ø124
ø1.5
ø1.7
ø2.0
ø2.5
ø3.0
ø3.1
in.
ø4.1
ø4.9
ø1.7
ø2.5
ø3.0
ø2.0
ø3.1
ø4.9
ø20
ø25
ø30
ø40
ø50
40 x 40 mm
95PA6RD20MMB4
95PA6RD25MMB4
95PA6RD30MMB4
95PA6RD40MMB4
95PA6RD50MMB4
95PA6SQ40MMB4
set of 4 pcs
50 x 50 mm
60 x 60 mm
ø1”
ø1.5”
ø2”
1” x 1”
95PA6SQ50MMB4
95PA6SQ60MMB4
95PA6RD10INCHB4
95PA6RD15INCHB4
95PA6RD20INCHB4
95PA6SQ10INCHB4
1.5” x 1.5”
2.5” x 2.5”
95PA6SQ15INCHB4
95PA6SQ25INCHB4
95PA6RD20MMB20
95PA6RD25MMB20
95PA6RD30MMB20
95PA6RD40MMB20
95PA6RD50MMB20
95PA6SQ40MMB20
95PA6SQ50MMB20
95PA6SQ60MMB20
95PA6RD10INCHB20
95PA6RD15INCHB20
95PA6RD20INCHB20
95PA6SQ10INCHB20
95PA6SQ15INCHB20
95PA6SQ25INCHB20
uni Retainer Ring™uni reference no.
set of 20 pcs
Prepared for M5set screw (1/4-20)
C
D
B
C
D
B
Prepared for M5set screw (1/4-20)
A
Standard Selection Accessories
uni Retainer Rings
uni Retainer Rings™
PA6-GF
Standard Material and Color
B
130
Technical Data Sheet for Belt/Chain Applications
Company/Customer:
Contact person:
End user:
Technical data
1. Industry:
2. Application:
3. Product type:
4. Wrapping/Container:
5. Item size (mm) L: xW: xH or Ø: xH: Other:
6. Product weight: kg/item kg/m kg/m2
7. Throughput: items/min. kg/min. Speed m/min.
8. Length of conveyor C-C: m Length of belt/chain: m Width of belt: m
9. Start/stop operation:
None Cardboard Shrink wrapped Flow pack Wood
Plastic trays Steel trays Glass Steel cans Alu cans Cross strapped Other:
No (continuous drive) Yes, no. of stops per hour Product indexing
No
10. Accumulation:
11. Min./max. operating temp.: °C / °C
12. Is the conveyor lubricated?
No Full
Yes, type:
Chain Single row
No13. Is the belt/chain exposed to any chemicals during operation? Yes, type:
No14. Is the belt/chain exposed to any chemicals during cleaning? Yes, type:
Parallel rows No. of rows15. Conveyor type: Belt or
Side flexing
Decline- If in-/decline angle to horizontal: °
Original belt/chain from:
16. Layout (birdseye) Straight running
Incline
Retrofit
POM PP PE PA Hardened steel Stainless steel
Stainless steel Other:
Other:
17. Horizontal layout
18.
or chain type:19. Belt type:
Belt or chain color:20. Belt or chain pitch:
21. Belt or chain material:
Plastic ( PP PE PA)
Lockpin
Hardened steel22. Pin material:
Endlock
Pinlock
Rodlock
rightleft
Y-lock
Wearpartlock
23. Pin retention system:
uni Flex SNB
Straight
Partlylength of accumulation:
rightleft Lockingplate rightleft
Ap
pli
cati
on
da
taB
elt/
cha
in
Plastic containers
New conveyor
Other:
131
Technical Data Sheet for Belt/Chain Applications
25. Side accessories: Indent from side:
No of rows:
no. of teeth z=pitch diameter:
Position:
per shaft pcs
no. of teeth z= (0 if non)
dimension
Date:
+ keyway
pitch diameter: per shaft pcs
26. Bottom tabs (belt): Spacing in travel direction:
27: Wearstrip material:
28: Sprockets : Drive end:
Idler end:
29. Sprocket bore: Drive end:
30. Form filled in by:
31. Sketch of conveyor, stating travel direction and drive motor location
Ad
dit
ion
al
info
rma
tio
n
SS PE HD 1000 PE HD500 Other
Additional data:
24. Top accessories: Spacing in travel direction Indent
132
Technical Data Sheet for Belt/Chain Applications
Company/Customer:
Contact person:
End user:
Technical data
1. Industry:
2. Application:
3. Product type:
4. Wrapping/Container:
5. Item size (in.) L: xW: xH or Ø: xH: Other:
6. Product weight: lb/item lbft lb/ft2
7. Throughput: items/min. lb/min. Speed ft/min.
8. Length of conveyor C-C: ft Length of belt/chain: ft Width of belt: ft
9. Start/stop operation:
None Cardboard Shrink wrapped Flow pack Wood
Plastic trays Steel trays Glass Steel cans Alu cans Cross strapped Other:
No (continuous drive) Yes, no. of stops per hour Product indexing
No
10. Accumulation:
11. Min./max. operating temp.: °F / °F
12. Is the conveyor lubricated?
No Full
Yes, type:
Chain Single row
No13. Is the belt/chain exposed to any chemicals during operation? Yes, type:
No14. Is the belt/chain exposed to any chemicals during cleaning? Yes, type:
Parallel rows No. of rows15. Conveyor type: Belt or
Side flexing
Decline- If in-/decline angle to horizontal: °
Original belt/chain from:
16. Layout (birdseye) Straight running
Incline
Retrofit
POM PP PE PA Hardened steel Stainless steel
Stainless steel Other:
17. Horizontal layout
18.
or chain type:19. Belt type:
Belt or chain color:20. Belt or chain pitch:
21. Belt or chain material:
Plastic ( PP PE PA)
Other:
Hardened steel22. Pin material:
Endlock
Pinlock
Rodlock
rightleft
Lockpin
Wearpartlock
23. Pin retention system:
uni Flex SNB
Straight
Partlylength of accumulation:
rightleft Lockingplate rightleft
Ap
pli
cati
on
da
taB
elt/
cha
in
Plastic containers
New conveyor
Other:
133
Technical Data Sheet for Belt/Chain Applications
25. Side accessories: Indent from side:
No of rows:
no. of teeth z=pitch diameter:
Position:
per shaft pcs
no. of teeth z= (0 if non)
dimension
Date:
+ keyway
pitch diameter: per shaft pcs
26. Bottom tabs (belt): Spacing in travel direction:
27: Wearstrip material:
28: Sprockets : Drive end:
Idler end:
29. Sprocket bore: Drive end:
30. Form filled in by:
31. Sketch of conveyor, stating travel direction and drive motor location
Ad
dit
ion
al
info
rma
tio
n
SS PE HD 1000 PE HD500 Other
Additional data:
24. Top accessories: Spacing in travel direction Indent
134
Disclaimeruni-chains® provides this catalog as a service and for information purposes only. The material and contents areprovided without warranty of any kind. This catalog is not intended to be used as a substitute for advice from ourengineers and our official guidelines. While we attempt to maintain the information in this catalog as accurately as possible, it may contain errors oromissions for which we deny any and all liability.
uni-chains® is not responsible for any property damage or personal injury, direct or indirect damage from failure ordown time in production caused by improper equipment construction. uni-chains® cannot be held responsible forthe incorrect application, operation and/or abuse of our products.
uni-chains® does not guarantee that the design and/or operational function of any equipment that incorporates uni-chains® products, conforms to local, state, and/or federal regulations. Nor does uni-chains® warrant that standards relating to safety aspects such as public and worker safety, safety guards, fire and sanitation safety, orany other safety regulations are met by such equipment or products.
All users should read our "Warnings" and "Design Safety Guidelines" before using our products.
135
Warnings
Fireuni-chains® plastic products are, unless clearly specified, made from materials which support open flame. Products made from POM material (D, I, LF and SLF), when so exposed, will emit toxic fumes. uni-chains®
plastic products should therefore not be exposed to extreme temperatures or open flame. Special care should be taken when undertaking repair work particularly when welding at a conveyor if the conveyor is equipped with plastic chains or belts.
Personal ProtectionAlways use safety glasses when installing or repairing chains and belts and while securing or removing pins. Use only suitable tools in good condition.The weight of some products calls for the use of safety shoes.When installing/removing or repairing chains or belts on a conveyor, the motor must be turned off.
Design Safety GuidelinesMost plastic products will lose their mechanical properties if exposed to the sun or ultraviolet beams, which can lead to chain or belt breakage. This can also happen if the products are exposed to strong chemicals.Generally, this is a problem with pH values lower than 4.5 or higher than 9.Always make sure that there is enough space in the conveyor frame to allow chains and belts to retract or expandwhen exposed to temperature variations.Never exceed the maximum or minimum temperatures given by uni-chains®.Note: The different materials have different temperature limits.
Care should be taken with high chain/belt speeds at which friction can lead to heating and subsequently melting of chain/belt as well as wearstrips. Do not exceed speeds recommended by uni-chains®.Use only original uni-chains sprockets with uni-chains® belts and chains.When constructing conveyors it is important to always include sufficient cover around the moving parts to preventfingers and clothing from being caught in the machinery. uni-chains® can also supply safety chains and side flexing belts which leave minimal gaps when turning through curves making them safer than regular chains.
136
Pitch
Materials
Side flexing
Backflex radius
Pin material
Endlock
Sprockets
Two part sprockets
Straight running
Straight running
Lockpin
Solid lockpin
Rodlock
Rubber inserts
Tabs
Accessories
Product support
Side guard
Finger plate
Reinforcement link
Molded to order
Single Link only
Not for use in brick-layed beltwidths.
G-lock
Blue
Brown
Red
Dark Grey
Green
Grey
Black
Natural
Ivory
Orange
Purple
Tan (Beige)
White
Yellow
Standard and alternative belt colors
uni Retainer Rings
Materials
MTO
SLO
B
BR
D
DG
E
G
K
N
O
P
T
W
Y
I