FUJITSU display B24-8 TE Pro / B24-8 TS Pro
-
Upload
khangminh22 -
Category
Documents
-
view
4 -
download
0
Transcript of FUJITSU display B24-8 TE Pro / B24-8 TS Pro
Congratulations on your purchase of an innovative
product from Fujitsu.
Latest information about our products, tips, updates etc. can be found onthe Internet at: "http://www.fujitsu.com/fts/"
You can find driver updates at: "http://support.ts.fujitsu.com/download"
Should you have any technical questions, please contact:
• our Hotline/Service Desk (see the Service Desk list or visit:"http://support.ts.fujitsu.com/contact/servicedesk")
• Your sales partner
• Your sales office
We hope you enjoy working with your new Fujitsu system!
Published by / Contact address in the EU
Fujitsu Technology Solutions GmbH
Mies-van-der-Rohe-Straße 8
80807 Munich, Germany
"http://www.fujitsu.com/fts/"
Copyright© Fujitsu Technology Solutions GmbH 2015. All rights reserved.
Publication Date12/2015
Order No.: A26361-K1577-Z320-1-7619, edition 1
FUJITSU displayB24-8 TE Pro / B24-8 TS Pro
Operating Manual
Your LCD screen... 5
Important notes 7
Getting started 11
Operation 18
Notes on ergonomic colour adjustment 29
Low blue light function 30
Explanatory information about
standard ISO 9241-307 31
Troubleshooting 32
Technical specification 34
Remarks
Notes on the product description meet the design requirements of Fujitsu and areprovided for the purposes of comparison. The actual results may differ due to severalfactors. Subject to technical changes without prior notification. Fujitsu accepts noresponsibility for technical or editorial mistakes or omissions.
Trademarks
Fujitsu and the Fujitsu logo are registered trademarks of Fujitsu Limited or itssubsidiaries in the United States and other countries.
Microsoft and Windows are trademarks or registered trademarks of the MicrosoftCorporation in the United States and/or other countries.
VESA, DDC and DPMS are registered trademarks of Video Electronics Standards Association.
All other trademarks specified here are the property of their respective owners.
Copyright
No part of this publication may be copied, reproduced or translated withoutthe prior written consent of Fujitsu.
No part of this publication may be saved or transmitted by any electronic meanswithout the written consent of Fujitsu.
Contents
ContentsYour LCD screen... . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5Target group . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5Further information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6Notational conventions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Important notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7Safety instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7Power cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8Transporting the device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8Cleaning the device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9CE marking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9Disposal and recycling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Getting started . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11Unpacking and checking the delivery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11Setting up the device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Setting up an ergonomic video workstation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12Mounting the monitor base . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14Adjusting height . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14Adjusting the inclination . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15Adjusting the rotation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15Removing monitor base . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15Connecting the device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16Connecting cables to the computer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18Switching the device on and off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18Notes on power management . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19Changing the monitor settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Changing the monitor settings with the buttons of the control panel . . . . . . . . . . . . . . . . . . . . . . 20Changing the monitor settings using the OSD menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
OSD menu functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24Adjusting the brightness and contrast . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25Selecting the application mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25Setting screen display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26Adjusting the volume . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26Setting colour temperature and colours . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27Setting the OSD menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27Advanced setting functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28Displaying information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Notes on ergonomic colour adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Low blue light function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Explanatory information about standard ISO 9241-307 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Technical specification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34VESA-DDC-compatible VGA interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35Preset operating modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Most frequent operating modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Fujitsu 3
Contents
Video/TV operating modes using DisplayPort or HDMI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36SUB D port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36DVI-D port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37DisplayPort socket . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38HDMI port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
4 Fujitsu
Your LCD screen...
Your LCD screen...has a whole range of useful features and functions, e.g.:
• TFT display (Thin Film Transistor; active matrix)
• minimal space requirements thanks to slim casing
• optimum ergonomic characteristics (totally distortion-free, excellent picturedefinition and colour purity right into the corners)
• high degree of brightness and good contrast
• high resolution (1920 x 1080)
• presentation of up to 16.7 million colours (in conjunction with an appropriate display adapter)
• automatic scanning of horizontal frequencies from 30 to 82 kHz and refresh rates(vertical frequencies) from 56 to 76 Hz (absolutely flicker-free)
• digital screen controller with microprocessor for storing 46 different display modes
• freely adjustable colour alignment for matching the screen colours to thecolours of various input and output devices
• convenient operation via integrated OSD (On-Screen-display) menu
• VESA-DDC compatibility
• VESA-FPMPMI compatibility (Flat Panel Monitor Physical Mounting Interface) –Mounting device for swivel arm or a similar accessory
• Plug&Play capability
• Digital video inputs (DVI, DP or HDMI) with HDCP
• power management for reducing power consumption when the computer is not in use
• Compliance with the recommendations according to TCO 7.0
• the monitor fulfills all GS ("Geprüfte Sicherheit", Certified Security) requirements.
This operating manual contains important information you require to start up and run your LCDmonitor.
A graphics card (display adapter) with VGA interface or a digital graphics card with DVI interfaceand/or a video signal source with DP interface for a B24-8 TE Pro monitor or with an HDMIinterface for a B24-8 TS Pro monitor is required to control the LCD monitor. The monitorprocesses the data supplied to it by the graphics card. The graphics card or the associateddriver software is responsible for setting the modes (resolution and refresh rate).
When putting the monitor into operation for the first time, the screen display should beoptimally adapted to the display adapter used and adjusted in accordance with yourneeds (see chapter "Changing the monitor settings", Page 19).
Target groupYou don’t need to be an "expert" to perform the operations described here.Nonetheless, it is important to always observe the safety notes given in the operatinginstructions for the computer and in this manual.
In the event of any problems, please contact your sales office or our Service Desk.
Fujitsu 5
Your LCD screen...
Further informationDetails of how you set the resolution and refresh rate are provided in the documentationfor your display adapter and the associated driver software.
For ergonomic reasons, we recommend a screen resolution of 1920 x 1080 pixels.
Because of the technology used (active matrix) an LCD monitor provides a totallyflicker-free picture even with a refresh rate of 60 Hz.
Notational conventionsPay particular attention to text marked with this symbol. Failure to observethese warnings could pose a risk to health, damage the device or leadto loss of data. The warranty will be invalidated if the device becomesdefective through failure to observe these warnings.
Indicates important information for the proper use of the device.
Indicates an activity that must be performed
Indicates a result
This font indicates data entered using the keyboard in a program dialogue or atthe command line, e.g. your password (Name123) or a command used tostart a program (start.exe)
This font indicates information that is displayed on the screen by a program, e.g.:Installation is complete.
This font indicates
• terms and texts used in a software interface, e.g.: Click on Save
• names of programs or files, e.g. Windows or setup.exe.
"This font" indicates
• cross-references to another section, e.g. "Safety information"
• cross-references to an external source, e.g. a web address: For moreinformation, go to "http://www.fujitsu.com/fts/"
• Names of CDs, DVDs and titles or designations of other materials, e.g.:"CD/DVD Drivers & Utilities" or "Safety" Manual
Key indicates a button on the monitor, e.g: MENU
This font indicates terms and texts that are emphasised or highlighted, e.g.: Donot switch off the device
6 Fujitsu
Important notes
Important notesImportantnotesNotes
In this chapter you will find information regarding safety which it is essential totake note of when working with your device.
Safety instructionsThis device complies with the relevant safety regulations for data processing equipment,including electronic office machines for use in an office environment. If you haveany questions about whether the device can be used in the intended environment,please contact your sales office or our Service Desk.
• The display surface of the device is sensitive to pressure and scratches. You should thereforebe careful with the display surface in order to avoid lasting damage (scratches).
• If the device is brought into the installation site from a cold environment, condensationcan form. Before operating the device, wait until it is absolutely dry and has reachedapproximately the same temperature as the installation site.
• When installing and operating the device, please observe the notes on environmentalconditions in Chapter "Technical specification", Page 34 as well as the instructions inChapter "Setting up an ergonomic video workstation", Page 12.
• To ensure sufficient ventilation, the air inlet and outlet openings of the device must be kept clear.
• The device automatically sets itself to the correct voltage within the range from 100 V to 240 V.Make sure that the local mains voltage is neither higher nor lower than this range.
• Ensure that the power socket on the device and the mains outlet are freely accessible.
• The ON/OFF switch does not disconnect the monitor from the mains voltage. To disconnectfully from the mains supply, disconnect the power plug from the socket.
• The device is equipped with a power cable that complies with safety standards.
• Use the supplied power cable only.
• Lay the cables in such a way that they do not create a hazard (danger of tripping)and cannot be damaged. When connecting the device, observe the relevantnotes in chapter "Connecting the device", Page 16.
• No data transfer cables should be connected or disconnected during a thunderstorm.
• Make sure that no objects (e.g. jewellery chains, paper clips, etc.) or liquids getinside the device (danger of electric shock, short circuit).
• The device is not waterproof! Never immerse the device in water and protectit from spray water (rain, sea water).
• In an emergency (e.g. damaged casing, operation controls or cables, penetrationof liquids or foreign matter), switch off the device, disconnect the power plugand contact your sales outlet or our Service Desk.
• Repairs to the device must only be performed by qualified technicians. Unauthorised openingand incorrect repair may greatly endanger the user (electric shock, fire risk).
• Only use the screen resolution settings and refresh rates specified in Chapter "Technicalspecification", Page 34. Otherwise you may damage the device. If you are in anydoubt, contact your sales outlet or our Service Desk.
• Use a screen saver with moving images and activate the power management foryour monitor to prevent still images from "burning in".
• If you operate the device with the swivel arm or a similar accessory, it must not be turned by 180°.
Fujitsu 7
Important notes
• The device may only be operated in wide format (0° landscape mode) and high format(90° portrait mode). The buttons of the control panel are located at the bottom inthe middle of the monitor in wide format (0° landscape mode) and at the left-handside of the monitor in high format (90° portrait mode).
• Store this manual close to the device. If you pass the device on to thirdparties, you should pass this manual on with it.
• We recommend that you place your device on a durable, non-slip surface. In viewof the many different finishes and varnishes used on furniture, it is possible that thefeet of the device may mark the surface they stand on.
• The device must be connected to protective earth.
• To prevent possible hearing damage, do not listen at high volume levels for long periods.
• Warning for excessive sound pressure from earphones and headphones:Excessive sound pressure from earphones and headphones can cause hearing loss.Adjustment of the equalizer to maximum increases the earphones and headphonesoutput voltage and therefore the sound pressure level.
Power cableUse the supplied power cable only.
Use the following guidelines if it is necessary to replace the original cable set.
• The female/male receptacles of the cord set must meet IEC60320/CEE-22 requirements.
• The cable has to be HAR-certified or VDE-certified. The mark HAR orVDE will appear on the outer sheath.
• For devices which are mounted on a desk or table, type SVT or SJT cable sets may beused. For devices which sit on the floor, only SJT type cable sets may be used.
• The cable set must be selected according to the rated current for your device.
• If necessary, replace the original power cable with a regular grounded 3-core mains lead.
Transporting the deviceDevice,TransportationRetransportation
Transport all parts separately in their original packaging or in a packaging whichprotects them from knocks and jolts, to the new site.
Do not unpack them until all transportation manoeuvres are completed.
If the device is brought from a cold environment into the room where it will be used,condensation may occur. Before operating the device, wait until it is absolutely dryand has reached approximately the same temperature as the installation site.
8 Fujitsu
Important notes
Cleaning the deviceSwitch off the device and unplug the power plug.
Do not clean any interior parts yourself, leave this job to a service technician.
Do not use any cleaning agents that contain abrasives or may corrode plastic.
Ensure that no liquid enters the device.
The display surface of the device is sensitive to pressure and scratches. Cleanit only using a soft, slightly moistened cloth.
The surface of the casing can be cleaned with a dry cloth. If particularly dirty, use a cloth thathas been moistened in mild domestic detergent and then carefully wrung out.
CE markingThe shipped version of this device complies with the requirements of EU directives 2004/108/EC"Electromagnetic compatibility", 2006/95/EC "Low voltage directive" and 2009/125/EC "Ecodesigndirective" (from 20.04.2016: 2014/30/EC "Electromagnetic compatibility", 2014/35/EG "Low voltagedirective").
Fujitsu 9
Important notes
Disposal and recyclingThis device has been manufactured as far as possible from materials which can be recycled ordisposed of in such a way that the environment is not damaged. The device may be taken back afteruse to be reused or recycled, provided that it is returned in a condition that befits its intended use.Any components not reclaimed will be disposed of in an environmentally acceptable manner.
The device must be disposed of in accordance with the local regulations for disposal of special waste.
If you have any questions on disposal, please contact your local sales office or ourService Desk, or contact one of the following directly:
Germany Belgium Switzerland
Fujitsu Technology SolutionsGmbH
Remarketing and Recycling
D-33106 Paderborn
Tel.: +49 5251 / 81 80 10
Fax: +49 5251 / 81 80 15
"http://fujitsu.com/fts/remarketing"
RECUPEL
Boulevard Reyers, 80
B-1030 Brussels
Tel.: +32 2 / 706 86 16
Fax: +32 2 / 706 86 13
E-Mail: [email protected]
"http://www.recupel.be"
SWICO
SchweizerischerWirtschaftsverbandder Informations-,Kommunikations- undOrganisationstechnik
A list of the SWICO acceptancelocations can be found at:"http://www.swico.ch"
Asia USA
Taiwan:
Environmental ProtectionAdministrationExecutive Yuan R.O.C.
"http://recycle.epa.gov.tw"
Fujitsu America, Inc.
1250E. Arques Avenue
Sunnyvale, CA 94085 U.S.A.
Phone No.: (408) 746-6000
You can also find more information on this at"http://www.fujitsu.com/fts/about/fts/environment-care/".
10 Fujitsu
Getting started
Getting started
Unpacking and checking the deliveryThe display surface of the device is sensitive to pressure and scratches.Always hold the device by the casing!
The complete device package includes:
• one monitor
• a data line (DP) for the B24-8 TS Pro
• one data cable (DVI)
• one USB cable
• one audio cable
• one power cable
• a flyer "Quick Start Guide"
• a safety instructions "flyer"
Unpack all the individual parts.
Check the contents of the package for any visible damage caused during transport.
Check whether the delivery conforms to the details in the delivery note.
Should you discover that the delivery does not correspond to the deliverynote, notify your local sales outlet immediately.
Do not discard the original packing material of the devices. You may need thepackaging in the future if you need to transport your device.
Fujitsu 11
Getting started
Setting up the deviceTo ensure sufficient ventilation, the air inlet and outlet openings ofthe device must be kept clear.
Setting up an ergonomic video workstation
1
Do not position the video workstationopposite a window (1).
1 Position the monitor outside the reach
of a light source (1).
12 Fujitsu
Getting started
1
Position the keyboard where it iseasiest to reach (1).
150 cm
Position the monitor so that the eye distanceto the screen (1) is around 50 cm.
Position the monitor for optimum viewing(1). The monitor should under nocircumstances fall outside the permissibleviewing space (2).
Depending on the situation, it may be advisable to use a swivel arm or similaraccessory (VESA FPMPMI), which are available from specialist dealers. Forthis purpose the monitor base must be removed beforehand as describedin Chapter "Removing monitor base", Page 15.
Fujitsu 13
Getting started
Mounting the monitor baseDo not remove the locking pin until you have secured the base plate on themonitor and moved it into the operating position.
1
2
Insert the base plate on the foot (1).
Secure the base plate with the screw (2).
Place the monitor in the operating position.
Adjusting heightThe height adjustment is fixed in the transport position.
1
2
To free the fixing, remove the lockingpin on the flange (1).
The height of the monitor can be adjustedby approximately 150 mm.
Grasp the monitor with both hands onthe right and left edge of the casingand move it up or down (2).
14 Fujitsu
Getting started
Adjusting the inclinationThe inclination of the monitor can be adjusted by -3° (forwards) and +35°(backwards) from its vertical position.
Hold the monitor with both hands on the left and right sides of the casingand move it to the desired angle.
Adjusting the rotationThe monitor can be rotated by ±170°.
Grasp the monitor with both hands on the right and left edge of the casingand turn it to the desired position.
Removing monitor baseBefore you can use a swivel arm or a similar accessory, you must remove the monitor base.
The display surface is susceptible to scratching!
1
2
Switch off the monitor and pull the powerplug out of the power socket.
Lay the monitor on its face on a soft surface.
Disconnect all cables.
To release the stand, remove the fourscrews that hold the stand in the VESAmount. Then lift the stand away upwards.
You can now mount a swivel arm or asimilar accessory in accordance with VESAFPMPMI using a hole spacing of 100 mm.
For instructions on how to mount the swivel arm or a similar accessory, pleasesee the documentation for the swivel arm or similar accessory.
Fujitsu 15
Getting started
Connecting the devicePlease observe the safety information in "Important notes", Page 7.
CE conformance and optimum picture quality are guaranteed only ifyou use the data cables supplied.
Switch off the monitor and the computer.
Disconnect the power plug from the computer.
Connecting cables to the monitor
The data cables supplied have two 20 pole DP connectors (B24-8 TE Pro) or two 24 poleDVI connectors for connection to the monitor and to the computer.
Information on the computer connections and interfaces is contained in theoperating manual for the computer.
2
1
5 643 9 107 8
1 = Security slot for Security Lock
2 = Power connector
3 = DisplayPort (B24-8 TE Pro)
4 = HDMI (B24-8 TS Pro)
5 = DVI-D socket (DVI)
6 = D-SUB socket (VGA)
7 = AUDIO-OUT socket
8 = AUDIO-IN socket
9 = USB 2.0 (Downstream)
10 = USB 2.0 (Upstream)
Select the appropriate data cable for your computer.
16 Fujitsu
Getting started
Insert the connector of the data cable into the D-SUB connector or DVI-D connector orinto the HDMI connector (B24-8 TS Pro) / DP connection socket (B24-8 TE Pro) of themonitor. Secure the plug-in connection by tightening the safety screws.
The monitor automatically detects the input when only one signal source is connected.
Insert one plug of the audio line in the AUDIO IN socket on the monitorand make sure it is properly engaged.
Plug the power cable supplied into the power connector of the monitor.
Plug the supplied USB cable into the USB IN socket and the other end ofthe cable into a USB socket of the computer.
Connect the USB keyboard and mouse directly to the PC, as the USB connectionsocket of the monitor is turned off in power-saving mode where possible.
A lock (Security Lock) can be mounted in the security slot to protect the monitoragainst theft. A Security Lock is not included with the monitor at delivery.
Connecting cables to the computerInformation on the computer connections and interfaces is contained in theoperating manual for your computer.
Connect the data cable to the (active) monitor port on the computer and securethe plug-in connection by tightening the safety screws.
Insert the other plug of the audio cable in the audio output of the computer.
Plug the power connector of the monitor into a properly grounded mains outlet.
Plug the power connector of the computer into a properly grounded mains outlet.
If your computer has two monitor ports ("onboard" screen controller and separategraphics card), the monitor port for the separate graphics card is active as standard.
Fujitsu 17
Operation
Operation
Switching the device on and off
1 2
1 2
1 = ON/OFF switch 2 = Power supply indicator
The colour of the power indicator changes as follows:
Power indicator Status
blue Monitor and computer are switched on (normal mode).green Monitor and computer are switched on (ECO mode).orange Monitor is not receiving a video signal or is in power saving mode.
does not light up Monitor is switched off.
Switch the device on again with the ON/OFF switch (1).
18 Fujitsu
Operation
Notes on power managementIf your computer is equipped with power management (power-saving mode), the monitor can fullysupport this function. Here the monitor does not distinguish between the individual energy-savingmodes of the computer (standby mode, suspend mode and OFF mode), as it is capable ofimmediately switching into the mode with the highest energy-saving effect.
Stage Operation Power saving mode
Normal ECO
Power supply indicator Lights up blue Lights up green Lights up orange
Display Max. brightness typ. 175 cd/m2 unlit
Typical powerconsumption (withoutUSB and audio)
< 25 W < 22 W < 0.3 W
If the computer detects inactivity (no input) it sends an appropriate signal to the monitor to reducethe power consumption (power saving mode). The power indicator of the monitor changescolour to show the change in status. ECO mode is the preset factory default.
Once an input is made at the computer the screen contents are restored.
For detailed information on how energy-saving mode operates, please refer tothe operating manual or technical manual of the computer.
Changing the monitor settingsWhen putting the monitor into operation for the first time, the screen display shouldbe optimally adapted to the display adapter used.
Fujitsu 19
Operation
Changing the monitor settings with the buttonsof the control panel
The buttons on the control panel have multiple functions. When the OSDmenu is active, the current meaning of the buttons is shown directlyover the buttons on the edge of the screen.
The display (softkey icon) over the buttons varies depending on the sub-menu chosen.
Key Function
Call up OSD menu
Activate/deactivate ECO operating mode
Select input signal (digital/analog)
Adjust volume
Adjust brightness
Perform auto-adjustment of the monitor with analog input
Monitor: switching on/off
Softkey icon Function
Selecting the next menu item (sub-menu)
Selecting the previous menu item (sub-menu)
Opening the selected sub-menu
Going to the next setting
Going to the previous setting
Decreasing the set value
Increasing the set value
Accepting the applied settings and returning to main menu
Cancelling the applied settings and returning to main menu
Exiting OSD menu
Loudspeaker: switching off/on
When the OSD menu is not activated, you can apply the following settings directly:
20 Fujitsu
Operation
Select OSD language
When an OSD menu button is activated for the first time, the language selection window will appear:
Press the button or the button to choose the desired language.
Press the button to confirm.
After selecting the OSD language for the first time, you can changeit at any time in the OSD.
Activate/deactivate ECO operating mode
The power consumption of the device can be decreased by reducingthe brightness of the picture.
Press the ECO button to switch the ECO operating mode on or off.
The message ECO Mode on or ECO Mode off is displayed.
If the ECO operating mode is activated, the following OSD settings are changed:
Mode Office
Color 6500 K
Brightness reduced
After the ECO operating mode is switched off, the brightness previously set by the user is restored.
Selecting the input signal
Press the INPUT button to open the Input select setting window.
Press the button or the button to select the desired monitor connection (VGA,DVI, HDMI for B24-8 TS Pro or DP for B24-8 TE Pro).
Press the button to confirm or the button to cancel.
This setting window can also be called up when the OSD menu is locked.
Adjusting the volume
Press the button to open the Volume setting window.
Press the button or the button to set the desired volume for the built-in speakers.
Press the button to activate/deactivate the mute function.
Press the button to close the menu.
Fujitsu 21
Operation
Adjusting the brightness
Press the button to open the Brightness setting window.
Press the button or the button to set the desired brightness.
Press the button to activate/deactivate the low blue light function.
Press the button to close the menu.
Performing auto-adjustment of the monitor
This function is only intended for analogue image transmission (VGA).
Press the AUTO button for about 1 second.
The Auto Processing message appears.
Picture quality and position are set to optimum values for your system.
Locking the OSD menu
The OSD menu can be locked to prevent accidental or unauthorised changes to the monitor settings.
Press the MENU button and the ON/OFF button at the same time for several seconds.
The message OSD locked / unlocked is displayed.
Please proceed in the same manner to release the locked OSD menu again.
Lock the ON/OFF button
The ON/OFF button can be locked to prevent accidental or unauthorisedchanges to the monitor settings.
Press the ECO button and INPUT button at the same time for a few seconds.
The message Power button locked / unlocked is displayed.
To remove the locking of the ON/OFF button again, proceed in the same way.
22 Fujitsu
Operation
Changing the monitor settings using the OSD menuWith the buttons on the control panel, you can call up and use the integratedOSD (On-Screen Display) menu.
The English menu names are used in the following description (default setting).
The OSD menu of your device may differ in several ways fromthe functional scope described.
The softkey icons may deviate from those shown here.
Press the MENU button to activate the OSD menu.
The OSD menu appears, with menu items for the setting functions.
The first menu item (Brightness/Contrast) is highlighted and the associatedfunctions are visible in the right-hand menu field.
Press the button or button to highlight another icon (e.g. Image).
Press the button to select the highlighted icon.
The Image setting window will be displayed.
Press the button to close the OSD menu.
Fujitsu 23
Operation
Press the button or button to highlight another function.
Press the button or the button to change the setting.
Press the button to save the change or the button to quit thefunction without making a change.
If you wish to change other settings, select the corresponding function from the OSDmain menu. All the settings options in the main menu are described below.
OSD menu functionsThe OSD menu for analogue monitor operation is described below. Duringdigital operation some functions are not available, as they are not requireddue to the digital transmission technology used.
24 Fujitsu
Operation
Adjusting the brightness and contrastCall up the Brightness/Contrast setting window
Brightness Set the brightness of the display
With this function you change the brightness of the background lighting.
Contrast Set the contrast of the display
With this function you modify the contrast of bright colour tones.
Black level Set the brightness of the display
With this function you modify the contrast of dark colour tones.
ACR Enable/disable dynamic contrast
This function improves the contrast by automatically controlling thebackground lighting in relation to the image being displayed.
This setting can only be configured in Video application mode.
Auto level Adjust the signal level
With this function you can automatically set the contrast.
The function is executed using .
If the contrast is set too high, bright surfaces can no longer be distinguished from verybright surfaces. If the contrast is set too low, the maximum brightness will not be achieved.
Selecting the application modeCall up the Mode setting window
sRGB Predefined settings for sRGB (reduced brightness)
Office Office settings (the settings for Color and sharpness can be adjusted)
Photo Predefined settings for Photo (Color, Sharpness, Saturation)
Video Predefined settings for Video (Colour, Sharpness, ACR)
Low blue light Default setting for low blue light (5000 K reduced brightness)
Fujitsu 25
Operation
Setting screen displayOpen the Image window
Phase Eliminate picture disturbance
With this function you fine-tune your monitor to eliminate picture disturbance.
Clock Set synchronisation
With this function you adjust the picture width to eliminate vertical picturedisturbances.
H-Position Adjust the horizontal position
With this function you move the picture to the left or to the right.
V-Position Adjust the vertical position
With this function you move the picture up or down.
Sharpness Adjust the sharpness of the picture for the Photo and Video modes.
Saturation Setting colour saturation
This setting only applies for devices with YUV output (e.g. BluRay players).
Hue Setting the colour tone
This setting only applies for devices with YUV output (e.g. BluRay players).
Expansion Adjust the picture size
Full screen = selection of full screen mode
Keep aspect = maximum picture size without distortion
Adjusting the volumeCall the Audio setting window
Volume Set the volume for playback with the integrated loudspeakers
Mute Switch the loudspeakers off or on
Input Selecting the audio input signal (DP, HDMI, PC Audio)
26 Fujitsu
Operation
Setting colour temperature and coloursOpening the Color setting window
Select the colour temperature
The "warmth" of the screen colours is set using the colour temperature. Thecolour temperature is measured in K (= Kelvin). You can choose betweensRGB, 5000 K, 6500 K, 7500 K, native and custom colour.
The options sRGB, Native and Custom Color are only available in the Officesetting mode.
You can change the colour ratios of the basic colours (red, green, blue) asrequired using Custom Color. You can use to select the colour channels.
The 6500K and sRGB settings are recommended for general Windowsapplications.
The setting 5000 K reduces the blue light emission of the monitor.
In the Native and Custom Color settings, the full colour space of the LCDpanel can be used.
Setting the OSD menuCall up the OSD window
Language Selecting the language for the OSD menu
With this function you select the language for the OSD menu.
The default setting is English.
Timeout Setting the display duration of the OSD menu
With this function you can select a value from 10 to 120 seconds.
If the set time expires without a setting being made, the OSD menu isautomatically hidden.
Rotation Adjust the orientation of the OSD menu.
This function can be used to turn the OSD menu through 90°.
This function makes it easier to read the OSD menu while the pivot functionis being used.
Auto = orientation of the OSD menu will be matched to the monitor.
On = OSD menu will be turned through 90°.
Fujitsu 27
Operation
Advanced setting functionsCalling up the Advanced window
Input select Select the input signal
This function is used to select the input signal (VGA, DVI, DP or HDMI).
This is on condition that the display adapter supports this function.
Overdrive Activating/deactivating the overdrive function
This function can be used to improve the focus in fast moving images.
This setting can only be configured in Video application mode.
DDC-CI Activating/deactivating the DDC-CI function
DDC-CI (Display Data Channel - Command Interface)
Data can be exchanged through the connection between the PC and thedisplay.
Factory recall Activate the factory settings
With this function all settings are reset to the factory settings onreconfirmation.
The function is executed using . The Auto Processing message is displayedvia a VGA data cable. The language selection menu appears.
Displaying informationCall the Information setting window
This function displays details such as the serial number, signal input,resolution, H/V frequency and ECO mode.
28 Fujitsu
Notes on ergonomic colour adjustment
Notes on ergonomic colour adjustmentIf you select colours for the monitor in your application programmes,take note of the information below.
The primary colours blue and red on a dark background do not produce the minimumrequired contrast of 3:1 and are therefore not suitable for continuous text and data entry.
When using several colours for characters and background and giving the primary colours fullmodulation, you can obtain very suitable colour combinations (see the following table):
CharactersBackground
black white purple blue cyan green yellow red
black + + - + + + -
white + + + - - - +
purple + + - - - - -
blue - + - + - + -
cyan + - - + - - -
green + - - + - - -
yellow + - + + - - +
red - + - - - - +
+ Colour combination very suitable
- Colour combination not suitable because colour hues are too close together, thin charactersare not identifiable or rigorous focusing is demanded of the human eye.
Fujitsu 29
Low blue light function
Low blue light functionThis monitor has a "low blue light" function, which can be selected in the OSD menu. This" lowblue light" function reduces the blue light emission of the monitor to a minimum. In this way, thedevice complies with the "low blue light" certification of the Technical Inspection Association.
LED backlights no longer emit blue light as a conventional source of white light.
30 Fujitsu
Explanatory information about standard ISO 9241-307
Explanatory information aboutstandard ISO 9241-307Permanently unlit or lit pixels
Today’s production techniques cannot guarantee an absolutely fault-free screen display. Dependingon the total number of pixels (resolution), there may be a few constantly lit or unlit pixels or subpixels.
Pixel A pixel consists of 3 subpixels, normally red, green and blue. A pixel isthe smallest element that can be generated by complete functionality ofthe display.
Subpixel A subpixel is a separately addressable internal structure within a pixel thatenhances the pixel function.
The maximum permitted number of faulty pixels is stipulated in the international standard ISO9241-307. In accordance with standard ISO 9241-3, LCD monitors by Fujitsu comply with Class IIfor low resolutions and Class I for resolutions of 1680 x 1050 (1764000 pixel) and higher.
Examples:
A flat-screen monitor with a resolution of 1280 x 1024 has 1280 x 1024 = 1310720 pixels. Each pixelconsists of three subpixels (red, green and blue), so there are almost 3.9 million subpixels in total.According to ISO 9241-3 (Class II), a maximum of 3 lit and 3 unlit pixels plus 7 lit or 13 unlit subpixels,or a corresponding combination, may be faulty (1 lit subpixel counts as two unlit subpixels).
A flat-screen monitor with a resolution of 1920 x 1080 has 1920 x 1080 = 2073600 pixels. Each pixelconsists of three subpixels (red, green and blue), so there are almost 6.2 million subpixels in total.According to ISO 9241-3 (Class I), a maximum of 2 lit and 2 unlit pixels plus 5 lit or 10 unlit subpixels,or a corresponding combination, may be faulty (1 lit subpixel counts as two unlit subpixels).
Fujitsu 31
Troubleshooting
TroubleshootingShould an error occur, first check the following points. If the distortion is still not eliminated,the monitor should, if possible, be checked on another computer.
If you cannot solve the problem, please contact our Service Desk.
Having this problem? Check the following points:
No screen display
Power indicator does not light up
Check whether the power cable on themonitor is connected correctly.
Check whether the computer is switched on.
No screen display
Power indicator is lit
Check whether the computer is switched on.
Check whether the data cable for themonitor is correctly attached to the monitorport on the computer.
Press any key on the computer keyboard.The computer may be in power savingmode.
Alter the brightness and/or contrast until youget a picture.
Message: No Signal Check whether the data cable for themonitor is correctly attached to the monitorport on the computer.
Check whether the computer is switched on.
Message: Frequency out of range:## kHz / ## HzPlease change the display modeto 1920 x 1080 with 60 Hz
The input signal (horizontal frequency andrefresh rate) at the displayed input does notcorrespond to the technical data for the monitor.
Adjust the video frequency range using thecomputer software (see documentation forthe computer or display adapter).
Set a different screen resolution using thecomputer software (see documentation forthe computer or display adapter).
Picture position not correct The monitor recognises an undefined mode (seechapter "Technical specification", Page 34).
Press the AUTO button to conduct theauto-adjustment of the screen.
Picture is shaking Check whether the data cable for themonitor is correctly attached to the monitorport on the computer.
Press the AUTO button to conduct theauto-adjustment of the screen.
Picture is wrongly adjusted Run the Factory Recall function in the OSDmenu.
The Auto Processing message appears.
32 Fujitsu
Troubleshooting
Having this problem? Check the following points:
Picture disturbances (vertical lines) Press the AUTO button to conduct theauto-adjustment of the screen.
Picture disturbances (horizontal lines, picturenoise)
Press the AUTO button to conduct theauto-adjustment of the screen.
The screen becomes darker The background lighting has a limited lifetime.If your monitor display should become too dark,the background lighting will have to be replaced.
Contact our Service Desk.
Fujitsu 33
Technical specification
Technical specificationCondensation is not permitted, neither in the rated range of operationnor in the limit range of operation.
B24-8 TE Pro / B24-8 TS Pro
Name of model B24-8T
Dimensions and weight
Visible diagonals 60.47 cm
Dot pitch 0.2745 mm
Width 527.04 mmImage size
Height 296.46 mm
Maximum resolution 1920 x 1080
Width 553 mm
Height 347 mm
Dimensions incl. monitor base
Depth 230 mm
Weight (without packaging) approx. 5.60 kg
Storable display modes 46
Pixel error classes accordingto ISO 9241-307
Class I
Electrical data
Analog Positive, 0.7 Vpp, 75 ΩVideo
Digital DVI-D, HDMI/DP with HDCP
Synchronisation Separate Sync. TTL,positive or negative
Horizontal frequency 30 kHz .... 82 kHz(multi-scanning)
Refresh rate 56 Hz .... 76 Hz
Maximum pixel rate 165 MHz
Power supply Switches automatically100 V – 240 V, 50/60 Hz
Normal operation < 25 W
ECO operating mode < 22 W
Typical power consumption(without audio, USB)
Power saving mode < 0.3 W
Sound output 2 W left; 2 W right
34 Fujitsu
Technical specification
Environmental conditions
Environment class 3K2, DIN IEC 721
Rated range of operation
Humidity
15 °C .... 35 °C
20 % .... 85 %
Limit range of operation
Humidity
5 °C .... 35 °C
15 % .... 85 %
VESA-DDC-compatible VGA interfaceYour monitor is equipped with a VESA-DDC-compatible VGA interface. VESA-DDC (VideoElectronics Standard Association, Display Data Channel) is used as the communicationsinterface between the monitor and the computer. If the computer is equipped with aVESA-DDC-compatible VGA interface, it can automatically read the data for ensuringoptimum operation from the monitor and select the appropriate settings.
Preset operating modesThe picture position and size have been set to optimum values at the factory for theoperating modes listed above. Depending on the display adapter used, it may benecessary to adjust the picture position and size. In this case, you can change andsave the settings (see chapter "Changing the monitor settings", Page 19).
For ergonomic reasons, a screen resolution of 1920 x 1080 pixels is recommended.Because of the technology used (active matrix), an LCD monitor provides atotally flicker-free picture, even with a refresh rate of 60 Hz.
Most frequent operating modesScreen resolution Refresh rate
640 x 480 60/75 Hz
720 x 400 70 Hz
800 x 600 60/75 Hz
1024 x 768 60/75 Hz
1280 x 720 60 Hz
1280 x 1024 60/75 Hz
1366 x 768 60 Hz
1440 x 900 60 Hz
1600 x 900 60 Hz
1680 x 1050 60 Hz
1920 x 1080 60 Hz
Fujitsu 35
Technical specification
Video/TV operating modes using DisplayPort or HDMIScreen resolution Refresh rate Aspect ratio
720 x 480 i 60 Hz 4:3 / 16:9
720 x 480 p 60 Hz 4:3 / 16:9
720 x 576 i 50 Hz 4:3 / 16:9
720 x 576 p 50 Hz 4:3 / 16:9
1280 x 720 p 50 / 60 Hz 16:9
1920 x 1080 i 50 / 60 Hz 16:9
1920 x 1080 p 50 / 60 Hz 16:9
SUB D port
610
1115
5 1
Pin Meaning
1 Video input red
2 Video input green
3 Video input blue
4 Ground
5 Ground
6 Video ground red
7 Video ground green
8 Video ground blue
9 +5 V (DDC)
10 Sync. ground
11 Ground
12 DDC Data
13 H. sync
14 V. sync
15 DDC Clock
36 Fujitsu
Technical specification
DVI-D port
9
1
17
Pin Meaning
1 TMDS Data2–
2 TMDS Data2+
3 TMDS Data 2/4 Shield
4 not connected
5 not connected
6 DDC Clock
7 DDC Data
8 Analog Vertical Sync
9 TMDS Data1–
10 TMDS Data1+
11 TMDS Data 1/3 Shield
12 not connected
13 not connected
14 +5V Power
15 Earth
16 Hot Plug Detect
17 TMDS Data0–
18 TMDS Data0+
19 TMDS Data 0/5 Shield
20 not connected
21 not connected
22 TMDS Clock Shield
23 TMDS Clock+
24 TMDS Clock–
Fujitsu 37
Technical specification
DisplayPort socketThe DisplayPort connection is only available in the model B24-8 TE Pro.
1319 17 15 13 11 9 7 5
2420 19 16 14 12 10 8 6
Pin Meaning
1 Lane 3 (negative)
2 Earth
3 Lane 3 (positive)
4 Lane 2 (negative)
5 Earth
6 Lane 2 (positive)
7 Lane 1 (negative)
8 Earth
9 Lane 1 (positive)
10 Lane 0 (negative)
11 Earth
12 Lane 0 (positive)
13 Connected to earth
14 Connected to earth
15 Auxiliary channel (positive)
16 Earth
17 Auxiliary channel (negative)
18 Hot Plug Detect
19 Return for Power
20 Power for connector(3.3 V 500 mA)
38 Fujitsu
Technical specification
HDMI portThe HDMI connection is only available in the model B24-8 TS Pro.
13
24681012141618
5791113151719
Pin Meaning
1 TMDS Data2+
2 TMDS Data2 Shield
3 TMDS Data2–
4 TMDS Data1+
5 TMDS Data1 Shield
6 TMDS Data1–
7 TMDS Data0+
8 TMDS Data0 Shield
9 TMDS Data0–
10 TMDS Clock+
11 TMDS Clock Shield
12 TMDS Clock–
13 CEC
14 N.C.
15 SCL
16 SDA
17 DDC/CEC Ground
18 +5 V Power
19 Hot plug detect
Fujitsu 39