SOP XGPON ALU Provisioning v1 13112014(1)

Standard Operating Procedure Provisioning

XGPON ALU 7360 ISAM

PT. Lintas Teknologi Indonesia

Menara MTH 16th

Floor Jl. MT Haryono Kav. 23 Jakarta 12820 - Indonesia

Telp. +62 21 8378 0000

Fax. +62 21 8378 0001

http://www.lt-indonesia.com 2013

http://www.lt-indonesia.com/

XGPON ALU 7360 ISAM Provisioning SOP 2

Sta

nd

ard

Op

era

tin

g P

roce

du

re

DOCUMENT CONTROL

Author : Rendi

Change Authority :

Revision History :

Version Number Date Issued Status Editor Reason for Change

1 26-10-2014 Draft Rendi Draft

Reviewers:

Name Organization Department Review Date

Approvals:

Name Organization Department Approval Date

Change Forecast: Low

Intellectual Property Rights This document contains valuable trade secrets and confidential information of ALU and its partners, and shall not be disclosed to any person, organization, or entity unless such disclosure is subject to the provisions of a written non-disclosure and proprietary rights agreement or intellectual property license agreement approved by ALU or LINTAS. The distribution of this document does not grant any license in or rights, in whole or in part, to the content, the product (s), technology, or intellectual property described herein.


Sta

nd

ard

Op

era

tin

g P

roce

du

re

Table of Contents

DOCUMENT CONTROL 2

1. INTRODUCTION 6

2. PERSON IN CHARGE (PIC) 6

3. PROVISIONING 7

3.1 I-240W-A ONT 7 3.1.1 TOPOLOGY 7 3.1.2 CONNECTIONS AND COMPONENTS 7 3.1.3 CREATE/MODIFY/DELETE ONT 9 3.1.4 CREATE/MODIFY/DELETE INTERNET SERVICE (PPPoE) 9 3.1.5 CREATE/MODIFY/DELETE IPTV SERVICE 9 3.1.6 CREATE/MODIFY/DELETE VOICE SERVICE 10

3.2 O-16160E-Q ONT 11 3.2.1 TOPOLOGY 11 3.2.2 CONNECTIONS AND COMPONENTS 11 3.2.3 CREATE/MODIFY/DELETE ONT 13 3.2.4 CREATE/MODIFY/DELETE INTERNET SERVICE (BRIDGE) 13 3.2.5 CREATE/MODIFY/DELETE IPTV SERVICE 13 3.2.6 CREATE/MODIFY/DELETE VOICE SERVICE 14

3.3 B-2404-P ONT 15 3.3.1 TOPOLOGY 15 3.3.2 CONNECTIONS AND COMPONENTS 15 3.3.3 CREATE/MODIFY/DELETE ONT 17 3.3.4 CREATE/DELETE E1 SERVICE 17

3.4 POINT TO POINT (P2P) (NELT-B) 19 3.4.1 TOPOLOGY 19 3.4.2 CONNECTIONS AND COMPONENTS 19 3.4.3 CREATE/MODIFY/DELETE TAGGED VLAN SERVICE 22

4. APPENDIX: PROVISIONING FLOW 23


Sta

nd

ard

Op

era

tin

g P

roce

du

re

List of Figures FIGURE 1 PHYSICAL TOPOLOGY OF I-240W-A INDOOR ONT AT PT. TELKOM INDONESIA 7 FIGURE 2 I-240W-A INDOOR ONT PHYSICAL CONNECTIONS (BACK VIEW) 7 FIGURE 3 I-240W-A INDOOR ONT PHYSICAL CONNECTIONS (SIDE VIEW) 7 FIGURE 4 I-240W-A INDOOR ONT LEDS 8 FIGURE 5 PHYSICAL TOPOLOGY OF O-16160E-Q MDU ONT AT PT. TELKOM INDONESIA 11 FIGURE 6 PHYSICAL CONNECTIONS ON THE FRONT OF O-16160E-Q MDU ONT 11 FIGURE 7 PHYSICAL CONNECTIONS ON THE BACK OF O-16160E-Q MDU ONT 11 FIGURE 8 O-16160E-Q MDU ONT LEDS 12 FIGURE 9 PHYSICAL TOPOLOGY OF E1 SFP TO B-2404-P ONT AT PT. TELKOM INDONESIA 15 FIGURE 10 PHYSICAL CONNECTIONS FOR B-2404-P BUSINESS ONTS 15 FIGURE 11 B-2404-P BUSINESS ONT LEDS 16 FIGURE 12 PHYSICAL TOPOLOGY OF P2P AT PT. TELKOM INDONESIA 19 FIGURE 13 FRONT VIEW OF THE NELT-B 19 FIGURE 14 BOARD LEDS ON THE NELT-B 19 FIGURE 15 LEDS FOR SFP PORTS 20 FIGURE 16 PHYSICAL OF 1000BASE-LX SFP 20 FIGURE 17 CREATE ONT FLOW 23 FIGURE 18 MODIFY ONT SERIAL NUMBER FLOW 23 FIGURE 19 DELETE ONT FLOW 23 FIGURE 20 CREATE INTERNET SERVICE FLOW (PPPOE) 23 FIGURE 21 MODIFY SERVICE BANDWIDTH FLOW 24 FIGURE 22 MODIFY INTERNET PPPOE USERNAME AND PASSWORD FLOW 24 FIGURE 23 DELETE INTERNET SERVICE FLOW (PPPOE) 24 FIGURE 24 CREATE INTERNET SERVICE FLOW (BRIDGE) 24 FIGURE 25 DELETE INTERNET SERVICE FLOW (BRIDGE) 25 FIGURE 26 CREATE IPTV SERVICE FLOW 25 FIGURE 27 DELETE IPTV SERVICE FLOW 25 FIGURE 28 CREATE VOICE SERVICE FLOW 26 FIGURE 29 MODIFY POTS PORT FLOW 26 FIGURE 30 DELETE VOICE SERVICE FLOW 26 FIGURE 31 CREATE E1 SERVICE FLOW 27 FIGURE 32 DELETE E1 SERVICE FLOW 28 FIGURE 33 CREATE POINT TO POINT TAGGED VLAN FLOW 29 FIGURE 34 DELETE POINT TO POINT TAGGED VLAN FLOW 29


Sta

nd

ard

Op

era

tin

g P

roce

du

re

List of Tables TABLE 1 I-240W-A INDOOR ONT PHYSICAL CONNECTIONS 8 TABLE 2 I-240W-A INDOOR ONT LEDS 8 TABLE 3 O-16160E-Q MDU ONT PHYSICAL CONNECTIONS 11 TABLE 4 O-16160E-Q MDU ONT LEDS 12 TABLE 5 B-2404-P BUSINESS ONT CONNECTIONS 15 TABLE 6 B-2404-P BUSINESS ONT LED DESCRIPTIONS 16 TABLE 7 LED DEFINITION FOR THE NELT-B 19 TABLE 8 BEHAVIOR OF LEDS FOR SFP PORTS 20 TABLE 9 OPTICAL PARAMETERS FOR ALCATEL-LUCENT APPROVED OPTICAL MODULES 21 TABLE 10 1000BASE-LX OPTICAL MODULE PARAMETERS 21


Sta

nd

ard

Op

era

tin

g P

roce

du

re

1. INTRODUCTION

This document has been prepared for reference of XGPON ALU 7360 provisioning at PT Telkom Indonesia.

2. PERSON IN CHARGE (PIC)

Name Company Phone Number Roles and Responsibilities

Rendi PT. Lintas Teknologi Indonesia

+62 82233167779 Senior Access Engineer


Sta

nd

ard

Op

era

tin

g P

roce

du

re

3. PROVISIONING

3.1 I-240W-A ONT

3.1.1 TOPOLOGY

Figure 1 Physical topology of I-240W-A indoor ONT at PT. Telkom Indonesia

3.1.2 CONNECTIONS AND COMPONENTS

Figure 2 I-240W-A indoor ONT physical connections (back view)

Figure 3 I-240W-A indoor ONT physical connections (side view)

1st IPTV

I-240W-A ONT

Splitter 1:8

Home Connection

FTM

7360 ISAM FX OLT

Splitter 1:4

PON

Internet

SIP Phone

2nd

IPTV Eth#1

Eth#2

Eth#3

Eth#4

POTS#1

POTS#2


Sta

nd

ard

Op

era

tin

g P

roce

du

re

Table 1 I-240W-A indoor ONT physical connections

Connection Description

Ethernet ports

This connection is provided through Ethernet RJ-45 connectors. Up to four 10/100 Base-T Ethernet interfaces are supported. The Ethernet ports can support both data and in-band video services on all four interfaces.

Fiber optic This connection is provided through an SC/APC fiber optic connector.

LED button This buttons turns all LEDs on or off.

POTS This connection is provided through RJ-11 ports. Up to two POTS connections are supported. The POTS ports support voice services.

Wireless button Wi-Fi service is compliant with IEEE 802.11 standards and is enabled and disabled using a Wireless button.

WPS button The Wi-Fi Protected Setup button is labeled WPS. This button enables and disables WLAN data encryption.

Power This connection is provided through the power connector. A power cable fitted with a barrel connector is used to make the connection.

USB ports This connection is provided through 2 USB ports.

Figure 4 I-240W-A indoor ONT LEDs

Table 2 I-240W-A indoor ONT LEDs

Indicator LED color and behavior LED behavior description

PWR Green solid Off

Operating on AC power No power source

Link Green solid Off

GPON link is OK GPON link is not OK

Auth Green solid Off

ONT is authorized ONT is not authorized

LAN 1 to 4 Green solid Off

Ethernet is linked ONT power off or Ethernet not connected

TEL 1 to 2 Green solid Green flashing Off

Off hook Call in On hook

VOIP Green solid Off

VOIP is OK VOIP is not OK

WPS Green solid Red Off

"In Progress" or "Success" status "Error" and "Session Overlap" status WPS not activated

WLAN Green solid Green flashing Off

Wireless enabled Traffic on wireless interface Wireless disabled


Sta

nd

ard

Op

era

tin

g P

roce

du

re

USB Green solid Green flashing Off

One or more USB device is connected One or more USB device is connected with traffic No USB device connected

INTERNET Green solid Off

HSI WAN is connected HSI WAN is not connected

3.1.3 CREATE/MODIFY/DELETE ONT

a. Create configure equipment ont interface 1/1/<SLOT>/<PON>/<ONT> sw-ver-pland 3FE54869ACEC29

sernum <ONT-SERNUM> subslocid WILDCARD voip-allowed iphost cvlantrans-mode local

configure equipment ont interface 1/1/<SLOT>/<PON>/<ONT> admin-state up

configure equipment ont slot 1/1/<SLOT>/<PON>/<ONT>/14 planned-card-type veip

plndnumdataports 1 plndnumvoiceports 0 admin-state up

configure equipment ont slot 1/1/<SLOT>/<PON>/<ONT>/1 planned-card-type 10_100base


configure equipment ont slot 1/1/<SLOT>/<PON>/<ONT>/2 planned-card-type pots


b. Modify ONT Serial Number configure equipment ont interface 1/1/<SLOT>/<PON>/<ONT> admin-state down

configure equipment ont interface 1/1/<SLOT>/<PON>/<ONT> sernum <NEW-ONT-SERNUM>


c. Delete configure equipment ont interface 1/1/<SLOT>/<PON>/<ONT> admin-state down

configure equipment ont no interface 1/1/<SLOT>/<PON>/<ONT>

3.1.4 CREATE/MODIFY/DELETE INTERNET SERVICE (PPPoE)

a. Create configure qos interface 1/1/<SLOT>/<PON>/<ONT>/14/1 upstream-queue 0 bandwidth-profile

name:<UP-BW>

configure qos interface 1/1/<SLOT>/<PON>/<ONT>/14/1 queue [0...3] shaper-profile

name:<DOWN-BW>

configure interface port uni:1/1/<SLOT>/<PON>/<ONT>/14/1 admin-up

configure bridge port 1/1/<SLOT>/<PON>/<ONT>/14/1 max-unicast-mac 4

configure bridge port 1/1/<SLOT>/<PON>/<ONT>/14/1 vlan-id 881 vlan-scope local network-

vlan <INTERNET-VLAN> single-tagged

configure veip ont 1/1/<SLOT>/<PON>/<ONT>/14/1 domain-name <PPPoE-USERNAME> admin-state up

configure ntp ont 1/1/<SLOT>/<PON>/<ONT> key <PPPoE-PASSWORD>

b. Modify Bandwidth configure qos interface 1/1/<SLOT>/<PON>/<ONT>/14/1 upstream-queue 0 bandwidth-profile

name:<NEW-UP-BW>


name:<NEW-DOWN-BW>

c. Modify PPPoE Username and Password configure veip ont 1/1/<SLOT>/<PON>/<ONT>/14/1 domain-name <PPPoE-USERNAME>

configure ntp ont 1/1/<SLOT>/<PON>/<ONT> key <PPPoE-PASSWORD>

d. Delete configure ntp ont 1/1/<SLOT>/<PON>/<ONT> no key

configure veip ont 1/1/<SLOT>/<PON>/<ONT>/14/1 no domain-name no admin-state

configure bridge no port 1/1/<SLOT>/<PON>/<ONT>/14/1

configure interface port uni:1/1/<SLOT>/<PON>/<ONT>/14/1 no admin-up

configure qos interface 1/1/<SLOT>/<PON>/<ONT>/14/1 queue [0...3] shaper-profile none

configure qos interface 1/1/<SLOT>/<PON>/<ONT>/14/1 upstream-queue 0 no bandwidth-profile

3.1.5 CREATE/MODIFY/DELETE IPTV SERVICE

a. Create configure qos interface 1/1/<SLOT>/<PON>/<ONT>/1/4 upstream-queue 0 bandwidth-profile

name:<UP-BW>


name:<DOWN-BW>

configure interface port uni:1/1/<SLOT>/<PON>/<ONT>/1/4 admin-up

configure bridge port 1/1/<SLOT>/<PON>/<ONT>/1/4 max-unicast-mac 4

configure bridge port 1/1/<SLOT>/<PON>/<ONT>/1/4 vlan-id 111

configure bridge port 1/1/<SLOT>/<PON>/<ONT>/1/4 pvid 111

configure igmp channel vlan:1/1/<SLOT>/<PON>/<ONT>/1/4:111 max-num-group 2

configure igmp channel vlan:1/1/<SLOT>/<PON>/<ONT>/1/4:111 preview-packages "[1...1024]"


Sta

nd

ard

Op

era

tin

g P

roce

du

re

b. Modify Bandwidth

configure qos interface 1/1/<SLOT>/<PON>/<ONT>/1/4 upstream-queue 0 bandwidth-profile

name:<UP-BW>

configure qos interface 1/1/<SLOT>/<PON>/<ONT>/1/4 queue [0...3] shaper-profile name:<NEW-

DOWN-BW>

c. Delete configure bridge no port 1/1/<SLOT>/<PON>/<ONT>/1/4

configure interface port uni:1/1/<SLOT>/<PON>/<ONT>/1/4 no admin-up

configure qos interface 1/1/<SLOT>/<PON>/<ONT>/1/4 queue [0...3] shaper-profile none

configure qos interface 1/1/<SLOT>/<PON>/<ONT>/1/4 upstream-queue 0 no bandwidth-profile

3.1.6 CREATE/MODIFY/DELETE VOICE SERVICE

a. Create configure qos interface 1/1/<SLOT>/<PON>/<ONT>/voip upstream-queue 0 bandwidth-profile

name:VOIP_UP-1M

configure qos interface 1/1/<SLOT>/<PON>/<ONT>/voip queue [0...3] shaper-profile

name:VOIP_DN-1M

configure bridge port 1/1/<SLOT>/<PON>/<ONT>/voip

configure bridge port 1/1/<SLOT>/<PON>/<ONT>/voip vlan-id <VOIP-VLAN> vlan-scope network

tag untagged

configure bridge port 1/1/<SLOT>/<PON>/<ONT>/voip pvid <VOIP-VLAN>

configure bridge port 1/1/<SLOT>/<PON>/<ONT>/vuni max-unicast-mac 2

configure iphost ont ont:1/1/<SLOT>/<PON>/<ONT>/1 dhcp enabled vlan <VOIP-VLAN>

configure iphost ont ont:1/1/<SLOT>/<PON>/<ONT>/1 admin-state up

configure voice ont voip-config ont:1/1/<SLOT>/<PON>/<ONT>/1 protocol sip conf-method omci

configure voice ont sip-config ont:1/1/<SLOT>/<PON>/<ONT>/1 proxyserv-prof 20

outproxyserv-prof 20 reg-expire-time 3600 re-reg-head-start 360 aor-host-prt-prof 21

registrar-prof 24 uri-format sip-uri dscp 46 opt-tx-cntrl disable

configure voice ont voice-sip-port 1/1/<SLOT>/<PON>/<ONT>/2/1 user-aor <VOIP-USER1> user-

name <VOIP-USER1>@telkom.net.id display-name <VOIP-USER1> password <VOIP-PWD1> realm

telkom.net.id ac-code-prof 2 app-serv-prof 8 ntwk-dp-prof 13

configure voice ont voice-port 1/1/<SLOT>/<PON>/<ONT>/2/1 voipconfig sip voip-media-prof 3

admin-state unlocked

b. Modify POTS Number configure voice ont pots 1/1/<SLOT>/<PON>/<ONT>/2/1 admin-state locked

configure voice ont voice-sip-port 1/1/<SLOT>/<PON>/<ONT>/2/1 user-aor <NEW-VOIP-USER1>

user-name <NEW-VOIP-USER1>@telkom.net.id display-name <NEW-VOIP-USER1> password <NEW-VOIP-

PWD1> realm telkom.net.id ac-code-prof 2 app-serv-prof 8 ntwk-dp-prof 13

configure voice ont pots 1/1/<SLOT>/<PON>/<ONT>/2/1 admin-state unlocked

c. Delete configure voice ont pots 1/1/<SLOT>/<PON>/<ONT>/2/1 admin-state locked

configure voice ont voice-sip-port 1/1/<SLOT>/<PON>/<ONT>/2/1 user-aor none user-name none

display-name none password none realm telkom.net.id no ac-code-prof no app-serv-prof no

ntwk-dp-prof

configure voice ont voice-port 1/1/<SLOT>/<PON>/<ONT>/2/1 voip-media-prof none

configure bridge no port 1/1/<SLOT>/<PON>/<ONT>/voip

configure qos interface 1/1/<SLOT>/<PON>/<ONT>/voip queue [0...3] shaper-profile none

configure qos interface 1/1/<SLOT>/<PON>/<ONT>/voip upstream-queue 0 no bandwidth-profile


Sta

nd

ard

Op

era

tin

g P

roce

du

re

3.2 O-16160E-Q ONT

3.2.1 TOPOLOGY

Figure 5 Physical topology of O-16160E-Q MDU ONT at PT. Telkom Indonesia


Figure 6 Physical connections on the front of O-16160E-Q MDU ONT

Figure 7 Physical connections on the back of O-16160E-Q MDU ONT

Table 3 O-16160E-Q MDU ONT physical connections

Connection type Description

Management

The first management interface (MGMT) is a craft port where connection is provided through an RJ-45 connector. The second management interface (CONSOLE) is a craft port where connection is provided through an RJ-45 connector.

1st IPTV

O-16160E-Q ONT

Splitter 1:8

Connection

FTM

7360 ISAM FX OLT

Splitter 1:4

PON

Internet

SIP Phone

2nd

IPTV Eth#1

Eth#2

Eth#3

Eth#4

POTS#1

POTS#16

……..

ETH#16

……..


Sta

nd

ard

Op

era

tin

g P

roce

du

re

Ethernet This connection is provided through an Ethernet RJ-45 cable. Up to 24 Ethernet connections are supported. The Ethernet ports support both data and in-band video services.

POTS For the O-24240E-Q, this interface is an RJ-21 connector with 48 positions which support up to 24 POTS lines. For the O-16160E-Q, this interface is an RJ-21 connector with 32 positions which support up to 16 POTS lines.

Fiber optic An SC/APC fiber optic connector terminates a fiber optic connection from the P-OLT.

dc power This connection is provided through an 8-pin UPS power connector.

grounding lug This connection is provided through a ground wire connected to the lug.

ac power This connection is provided by an ac power cord with a three-pronged female plug.

12 V battery backup This connection is provided by a power cord with a two-pronged female plug.

Figure 8 O-16160E-Q MDU ONT LEDs

Table 4 O-16160E-Q MDU ONT LEDs

LED name LED color LED behavior description

PWR Off Green

No power Power on

ALM Off Red

Normal System failure

NET Off Green

Optical path error 1490 nm data path (downstream) is OK and PLOAM has been exchanged with the OLT

MGMT Off Green

ONU is not register to OLT Full communication with ranging sync established between OLT and ONT

SIGN Off Green

VoIP not registered VoIP registered

RTP Off Green

All of the POTS ports on-hook One or more of the POTS ports off-hook

MODE Off Green

10M 100M

LINK Off Yellow Solid Yellow flashing

Link not up Link up Link up and Rx or Tx activity detected


Sta

nd

ard

Op

era

tin

g P

roce

du

re


a. Create configure equipment ont interface 1/1/<SLOT>/<PON>/<ONT> sw-ver-pland 3FE53866AOCK26

sernum <ONT-SERNUM> subslocid WILDCARD voip-allowed iphost cvlantrans-mode local






configure equipment ont slot 1/1/<SLOT>/<PON>/<ONT>/2 planned-card-type pots


b. Modify ONT S/N (Serial Number) configure equipment ont interface 1/1/<SLOT>/<PON>/<ONT> admin-state down





3.2.4 CREATE/MODIFY/DELETE INTERNET SERVICE (BRIDGE)

a. Create configure qos interface 1/1/<SLOT>/<PON>/<ONT>/<10 or 11>/<PORT> upstream-queue 0

bandwidth-profile name:<UP-BW>

configure qos interface 1/1/<SLOT>/<PON>/<ONT>/<10 or 11>/<PORT> queue [0...3] shaper-

profile name:<DOWN-BW>

configure interface port uni:1/1/<SLOT>/<PON>/<ONT>/<10 or 11>/<PORT> admin-up

configure bridge port 1/1/<SLOT>/<PON>/<ONT>/<10 or 11>/<PORT> max-unicast-mac 4

configure bridge port 1/1/<SLOT>/<PON>/<ONT>/<10 or 11>/<PORT> vlan-id <INTERNET-VLAN>

configure bridge port 1/1/<SLOT>/<PON>/<ONT>/<10 or 11>/<PORT> pvid <INTERNET-VLAN>

b. Modify Bandwidth configure qos interface 1/1/<SLOT>/<PON>/<ONT>/<10 or 11>/<PORT> upstream-queue 0

bandwidth-profile name:<NEW-UP-BW>


profile name:<NEW-DOWN-BW>

c. Delete configure bridge no port 1/1/<SLOT>/<PON>/<ONT>/<10 or 11>/<PORT>

configure interface port uni:1/1/<SLOT>/<PON>/<ONT>/<10 or 11>/<PORT> no admin-up


profile none

configure qos interface 1/1/<SLOT>/<PON>/<ONT>/<10 or 11>/<PORT> upstream-queue 0 no

bandwidth-profile

3.2.5 CREATE/MODIFY/DELETE IPTV SERVICE

a. Create configure qos interface 1/1/<SLOT>/<PON>/<ONT>/<10 or 11>/<PORT> upstream-queue 0



profile name:<DOWN-BW>

configure interface port uni:1/1/<SLOT>/<PON>/<ONT>/<10 or 11>/<PORT> admin-up

configure bridge port 1/1/<SLOT>/<PON>/<ONT>/<10 or 11>/<PORT> max-unicast-mac 4

configure bridge port 1/1/<SLOT>/<PON>/<ONT>/<10 or 11>/<PORT> vlan-id 111

configure bridge port 1/1/<SLOT>/<PON>/<ONT>/<10 or 11>/<PORT> pvid 111

configure igmp channel vlan:1/1/<SLOT>/<PON>/<ONT>/<10 or 11>/<PORT>:111 max-num-group 2

configure igmp channel vlan:1/1/<SLOT>/<PON>/<ONT>/<10 or 11>/<PORT>:111 preview-packages

"[1...1024]"

b. Modify Bandwidth configure qos interface 1/1/<SLOT>/<PON>/<ONT>/<10 or 11>/<PORT> upstream-queue 0



profile name:<NEW-DOWN-BW>

c. Delete configure bridge no port 1/1/<SLOT>/<PON>/<ONT>/<10 or 11>/<PORT>

configure interface port uni:1/1/<SLOT>/<PON>/<ONT>/<10 or 11>/<PORT> no admin-up


profile none


Sta

nd

ard

Op

era

tin

g P

roce

du

re

configure qos interface 1/1/<SLOT>/<PON>/<ONT>/<10 or 11>/<PORT> upstream-queue 0 no

bandwidth-profile

3.2.6 CREATE/MODIFY/DELETE VOICE SERVICE

a. Create configure qos interface 1/1/<SLOT>/<PON>/<ONT>/voip upstream-queue 0 bandwidth-profile

name:VOIP_UP-1M

configure qos interface 1/1/<SLOT>/<PON>/<ONT>/voip queue [0...3] shaper-profile

name:VOIP_DN-1M

configure bridge port 1/1/<SLOT>/<PON>/<ONT>/voip

configure bridge port 1/1/<SLOT>/<PON>/<ONT>/voip vlan-id <VOIP-VLAN> vlan-scope network

tag untagged

configure bridge port 1/1/<SLOT>/<PON>/<ONT>/voip pvid <VOIP-VLAN>

configure bridge port 1/1/<SLOT>/<PON>/<ONT>/vuni max-unicast-mac 2

configure iphost ont ont:1/1/<SLOT>/<PON>/<ONT>/1 dhcp enabled vlan <VOIP-VLAN>

configure iphost ont ont:1/1/<SLOT>/<PON>/<ONT>/1 admin-state up

configure voice ont voip-config ont:1/1/<SLOT>/<PON>/<ONT>/1 protocol sip conf-method omci

configure voice ont sip-config ont:1/1/<SLOT>/<PON>/<ONT>/1 proxyserv-prof 20

outproxyserv-prof 20 reg-expire-time 3600 re-reg-head-start 360 aor-host-prt-prof 21

registrar-prof 24 uri-format sip-uri dscp 46 opt-tx-cntrl disable

configure voice ont voice-sip-port 1/1/<SLOT>/<PON>/<ONT>/2/<PORT> user-aor <VOIP-USER1>

user-name <VOIP-USER1>@telkom.net.id display-name <VOIP-USER1> password <VOIP-PWD1> realm

telkom.net.id ac-code-prof 2 app-serv-prof 8 ntwk-dp-prof 13

configure voice ont voice-port 1/1/<SLOT>/<PON>/<ONT>/2/<PORT> voipconfig sip voip-media-

prof 4 admin-state unlocked

b. Modify POTS Number configure voice ont pots 1/1/<SLOT>/<PON>/<ONT>/2/<PORT> admin-state locked

configure voice ont voice-sip-port 1/1/<SLOT>/<PON>/<ONT>/2/<PORT> user-aor <NEW-VOIP-

USER1> user-name <NEW-VOIP-USER1>@telkom.net.id display-name <NEW-VOIP-USER1> password

<NEW-VOIP-PWD1> realm telkom.net.id ac-code-prof 2 app-serv-prof 8 ntwk-dp-prof 13

configure voice ont pots 1/1/<SLOT>/<PON>/<ONT>/2/<PORT> admin-state unlocked

c. Delete configure voice ont pots 1/1/<SLOT>/<PON>/<ONT>/2/<PORT> admin-state locked

configure voice ont voice-sip-port 1/1/<SLOT>/<PON>/<ONT>/2/<PORT> user-aor none user-name

none display-name none password none realm telkom.net.id no ac-code-prof no app-serv-prof

no ntwk-dp-prof

configure voice ont voice-port 1/1/<SLOT>/<PON>/<ONT>/2/<PORT> voip-media-prof none

configure bridge no port 1/1/<SLOT>/<PON>/<ONT>/voip

configure qos interface 1/1/<SLOT>/<PON>/<ONT>/voip queue [0...3] shaper-profile none

configure qos interface 1/1/<SLOT>/<PON>/<ONT>/voip upstream-queue 0 no bandwidth-profile


Sta

nd

ard

Op

era

tin

g P

roce

du

re

3.3 B-2404-P ONT

3.3.1 TOPOLOGY

Figure 9 Physical topology of E1 SFP to B-2404-P ONT at PT. Telkom Indonesia


Figure 10 Physical connections for B-2404-P business ONTs

Table 5 B-2404-P business ONT connections

Connection Function

E1/T1 connections There are up to four E1/T1 ports supporting unstructured and fractional E1/T1 through RJ-48C connectors. Currently, E1 connections are supported while T1 connections are not.

Ethernet connections There are up to four Ethernet port supporting 10/100/1000Base-T Ethernet connections through Ethernet RJ-45 connectors.

PON optical connection This connection is provided through an SC/APC connector for the physical interface to the PON.

Power connection A terminal is provided to connect an external –12 V dc UPS to the ONT.

B-2404-P ONT

Splitter 1:8

Connection

FTM

7360 ISAM FX OLT

Splitter 1:4

PON

E1#1…4 E1 SFP


Sta

nd

ard

Op

era

tin

g P

roce

du

re

Figure 11 B-2404-P business ONT LEDs

Table 6 B-2404-P business ONT LED descriptions

Indicator Color Description

PWR

Green solid Green flashing slow Green flashing fast Red solid

Operating from AC power Operating from battery power System booting Battery low

GPON

Off Green solid Green flashing slow Red solid

Optical Not OK Optical OK; Ranged PON is in ranging and synchronizing process Optical Power Off (LOS/LOF)

DATA Off Green solid Green flash

Ethernet service is not configured in ONT Ethernet service is configured in ONT Ethernet service is configured and there is activity of receiving or transmitting data

CES

Off Green solid Green flashing

CES data path is not setup CES data path is ready LED blinks when links are up and there is activity (data receive and transfer). LED blinks with a 167 ms cycle and 50% duty cycle.

TIMING Off Green solid Green flashing

Reference clock is not valid Reference clock ready In holdover state

UPDATE Off Green flashing fast Red solid

Normal status Upgrading Upgrade failure

ALARM Off Green solid Red solid

Normal status No alarm with local Ethernet access enabled (for Telnet) Indicates hardware failure

POTS Off Green solid Green flashing fast

Telephone at POTS A and B are all in the on hook condition Telephone at POTS A and B are all in the off hook condition At least one POTS is in off hook condition for at least one hour

TEST Off Green solid Green flashing fast

Normal status ONT is under loopback test ONT is in normal state with local Ethernet access (for Telnet) enabled


Sta

nd

ard

Op

era

tin

g P

roce

du

re


a. Create configure equipment ont interface 1/1/<SLOT>/<PON>/<ONT> sw-ver-pland 3FE54603AOCI35

sernum <ONT-SERNUM> subslocid WILDCARD voip-allowed enable cvlantrans-mode local


configure equipment ont slot 1/1/<SLOT>/<PON>/<ONT>/5 planned-card-type e1


b. Modify ONT S/N (Serial Number) configure equipment ont interface 1/1/<SLOT>/<PON>/<ONT> admin-state down





3.3.4 CREATE/DELETE E1 SERVICE

a. Create configure vlan id <VLAN-ID> mode cross-connect name <SERVICE-DESCRIPTION> in-qos-prof-name

name:Default_TC0

configure service customer <CUSTOMER-ID> description <CUSTOMER-DESCRIPTION>

configure service vpls <VLAN-ID> customer <CUSTOMER-ID> create

configure service vpls <VLAN-ID> description <SERVICE-DESCRIPTION>

configure service vpls <VLAN-ID> sap lt:1/1/<SLOT-ONT>:<VLAN-ID> create

configure service vpls <VLAN-ID> sap lt:1/1/15:<VLAN-ID> create

configure service vpls <VLAN-ID> user-user-com

configure service vpls <VLAN-ID> no shutdown

///SFP

configure ethernet line 1/1/15/<PORT> port-type uni admin-up

configure ethernet line 1/1/15/<PORT> mau 1 type 1000baselxfd power up

configure equipment sfpe1t1 clock lt: 1/1/15/<PORT> clocksource serdes

configure equipment sfpe1t1 pwtdm lt: 1/1/15/<PORT>:<E1-NUMBER> channel open packet-length

256 jitter-buff-size 7 vlanid <VLAN-ID> priority 6 conseq-number 2 ecid-rx <ECID-RX-DEC>

ecid-tx <ECID-TX-DEC> source-mac <SRC-MAC@> dest-mac <DEST-MAC@>

configure equipment sfpe1t1 framer lt: 1/1/15/<PORT>:<E1-NUMBER> frame-mode unframed

configure equipment sfpe1t1 liu lt: 1/1/15/<PORT>:<E1-NUMBER> distance longhaul cable-

impedance 120ohms

configure bridge port 1/1/15/<PORT> max-unicast-mac 10

configure bridge port 1/1/15/<PORT> vlan-id <VLAN-ID> tag single-tagged

// ONT

configure interface port uni:1/1/<SLOT>/<PON>/<ONT>/5/<PORT> admin-up

configure qos interface 1/1/<SLOT>/<PON>/<ONT>/5/<PORT> upstream-queue 0 bandwidth-profile

name:E1

configure qos interface 1/1/<SLOT>/<PON>/<ONT>/5/<PORT> queue [0...3] shaper-profile

name:E1

configure bridge port 1/1/<SLOT>/<PON>/<ONT>/5/<PORT> max-unicast-mac 10

configure bridge port 1/1/<SLOT>/<PON>/<ONT>/5/<PORT> vlan-id <VLAN-ID>

configure bridge port 1/1/<SLOT>/<PON>/<ONT>/5/<PORT> pvid <VLAN-ID>

configure ces ont profile <ID> profile-name <NAME> jitter-buff-max 100

configure ces ont line 1/1/<SLOT>/<PON>/<ONT>/5/<PORT> mode unstructured frame unframed

encoding hdb3 line-length 120ohms

configure ces ont service 1/1/<SLOT>/<PON>/<ONT>/5/<PORT> service-nbr 1 vlan <VLAN-ID>

timing-mode adaptive maintenance-prof 2 payload-size 256 transmit-ckt-id <TX-CKT-ID-HEX>

expected-ckt-id <DEST-CKT-ID-HEX> dest-mac-address <DEST-MAC@>

b. Delete configure bridge no port 1/1/15/<PORT>

configure equipment sfpe1t1 no pwtdm lt:1/1/15/<PORT>:<E1-NUMBER>

configure equipment sfpe1t1 no clock lt:1/1/15/<PORT>

configure ethernet line 1/1/15/<PORT> mau 1 power down

configure ethernet line 1/1/15/<PORT> no admin-up

configure ces ont no service 1/1/<SLOT>/<PON>/<ONT>/5/<PORT>

configure ces ont line 1/1/<SLOT>/<PON>/<ONT>/5/<PORT> no admin-state

configure ces ont no profile <ID>

configure bridge no port 1/1/<SLOT>/<PON>/<ONT>/5/<PORT>

configure interface port uni:1/1/<SLOT>/<PON>/<ONT>/5/<PORT> no admin-up

configure qos interface 1/1/<SLOT>/<PON>/<ONT>/5/<PORT> queue [0...3] shaper-profile none

configure qos interface 1/1/<SLOT>/<PON>/<ONT>/5/<PORT> upstream-queue 0 no bandwidth-

profile

configure vlan no id <VLAN-ID>


Sta

nd

ard

Op

era

tin

g P

roce

du

re

configure service vpls <VLAN-ID> shutdown

configure service vpls <VLAN-ID> sap lt:1/1/<SLOT>:<VLAN-ID> shutdown

configure service vpls <VLAN-ID> no sap lt:1/1/<SLOT-ONT>:<VLAN-ID>

configure service vpls <VLAN-ID> sap lt:1/1/15:<VLAN-ID> shutdown

configure service vpls <VLAN-ID> no sap lt:1/1/15:<VLAN-ID>

configure service no vpls <VLAN-ID>

configure service no customer <CUSTOMER-ID>


Sta

nd

ard

Op

era

tin

g P

roce

du

re

3.4 POINT TO POINT (P2P) (NELT-B)

3.4.1 TOPOLOGY

Figure 12 Physical topology of P2P at PT. Telkom Indonesia


Figure 13 Front view of the NELT-B

Figure 14 Board LEDS on the NELT-B

Table 7 LED Definition for the NELT-B

LED Color Description

ALM Red Alert

A/S Green Active/Standby

PWR Green On line

7360 ISAM FX OLT

1 GbE SFP in NELT-B LT card

MSAN/SWITCH


Sta

nd

ard

Op

era

tin

g P

roce

du

re

Figure 15 LEDs for SFP Ports

Table 8 Behavior of LEDs for SFP Ports

Situation Status LED

Board reset Off

Link administrative down Off

Link administrative up and Loss Of signal (LOS) Off

Link administrative up and Signal detected On

Link is OK and carrying traffic Blinking

Figure 16 Physical of 1000Base-LX SFP


Sta

nd

ard

Op

era

tin

g P

roce

du

re

Table 9 Optical parameters for Alcatel-Lucent approved optical modules

Part Number Description Wavelength Reach Operating

Temperature Optical Budget

Fiber mode

Gigabit Ethernet optical modules for optical connections

3FE 25774 AA 1 Gb/s Ethernet 1000Base-LX 1310 nm 10 km -40°C to + 85°C 11 dB SMF

Table 10 1000Base-LX optical module parameters

Parameter Minimum Typical Maximum

Absolute Maximum Ratings

Storage temperature -40°C - +85°C

Operating case temperature(1) -5°C - +85°C

Supply voltage 0V - +5.0V

Operating data rate - 1250 Mb/s -

Transmitter Performance Characteristics

Optical output power(2) -9.0 dBm - -3.0 dBm

TX wavelength 1260 nm 1310 nm 1360 nm

Center wavelength 1274 nm 1310 nm 1360 nm

Spectral width (-20dB) - - 4.0 nm

Extinction ratio 9 dB - -

Deterministic jitter - - 80 ps

Total jitter - - 227 ps

Relative intensity noise - - -120 dB/Hz

Transmitter output eye Compliant with IEEE 802.3z and FC-PI eye mask

Receiver Performance Characteristics

Operating data rate(4) - 1250 Mb/s -

Input optical power (10-12 BER)(2) -22.0 dBm - -3.0 dBm(5)

LOS thresholds, increasing light input - - -22.0 dBm

LOS thresholds, decreasing light input -30.0 dBm - -

LOS Hysteresis 0.5 dB - -

Deterministic jitter - - 170 ps

Total jitter - - 266 ps

Wavelength of operation 1100 nm - 1600 nm

Optical return loss 12 dB - -

Electrical 3 dB upper cut-off frequency - - 1500 MHz

Electrical 3 dB upper cut-off frequency Compliant with IEEE 802.3z standard


Sta

nd

ard

Op

era

tin

g P

roce

du

re

3.4.3 CREATE/MODIFY/DELETE TAGGED VLAN SERVICE

a. Create configure vlan id <VLAN-ID> mode cross-connect name <SERVICE-DESCRIPTION> in-qos-prof-name

name:Default_TC0

configure service customer <CUSTOMER-ID> description <CUSTOMER-DESCRIPTION>

configure service vpls <VLAN-ID> customer <CUSTOMER-ID> create

configure service vpls <VLAN-ID> description <SERVICE-DESCRIPTION>

configure service vpls <VLAN-ID> sap lag-1:<VLAN-ID> create

configure service vpls <VLAN-ID> sap lt:1/1/16:<VLAN-ID> create

configure service vpls <VLAN-ID> no shutdown

configure interface port ethernet-line:1/1/16/<PORT> admin-up

configure ethernet line 1/1/16/<PORT> port-type uni admin-up

configure ethernet line 1/1/16/<PORT> mau 1 type 1000baselx10 speed-auto-sense power up

configure bridge port 1/1/16/<PORT> max-unicast-mac 10

configure bridge port 1/1/16/<PORT> vlan-id <VLAN-ID> tag single-tagged

b. Delete configure bridge no port 1/1/16/<PORT>

configure ethernet line 1/1/16/<PORT> mau 1 no speed-auto-sense power down

configure ethernet line 1/1/16/<PORT> no admin-up

configure interface port ethernet-line:1/1/16/<PORT> no admin-up

configure service vpls <VLAN-ID> shutdown

configure service vpls <VLAN-ID> sap lag-1:<VLAN-ID> shutdown

configure service vpls <VLAN-ID> no sap lag-1:<VLAN-ID>

configure service vpls <VLAN-ID> sap lt:1/1/16:<VLAN-ID> shutdown

configure service vpls <VLAN-ID> no sap lt:1/1/16:<VLAN-ID>

configure service no vpls <VLAN-ID>

configure service no customer <CUSTOMER-ID>

configure vlan no id <VLAN-ID>


Sta

nd

ard

Op

era

tin

g P

roce

du

re

4. APPENDIX: PROVISIONING FLOW

Figure 17 Create ONT flow

Figure 18 Modify ONT serial number flow

Figure 19 Delete ONT flow

Figure 20 Create internet service flow (PPPoE)

1. SET UPSTREAM QOS INTERFACE

2. SET DOWNSTREAM QOS INTERFACE

3. UNLOCK INTERFACE PORT

4. CREATE BRIDGE PORT VLAN TRANS 881

5. SET PPPOE USERNAME

6. SET PPPOE PASSWORD

1. LOCK EQUIPMENT ONT INTERFACE

2. DELETE EQUIPMENT ONT INTERFACE

1. LOCK EQUIPMENT ONT INTERFACE

2. MODIFY EQUIPMENT ONT INTERFACE

2. UNLOCK EQUIPMENT ONT INTERFACE

1. CREATE EQUIPMENT ONT INTERFACE

2. UNLOCK EQUIPMENT ONT INTERFACE

3. CREATE EQUIPMENT ONT SLOT


Sta

nd

ard

Op

era

tin

g P

roce

du

re

Figure 21 Modify service bandwidth flow

Figure 22 Modify internet PPPoE username and password flow

Figure 23 Delete internet service flow (PPPoE)

Figure 24 Create internet service flow (Bridge)

1. DELETE PPPOE PASSWORD

2. DELETE PPPOE USERNAME

3. DELETE BRIDGE PORT

4. LOCK INTERFACE PORT

5. DELETE DOWNSTREAM QOS INTERFACE

6. DELETE UPSTREAM QOS INTERFACE

1. MODIFY PPPOE USERNAME

2. MODIFY PPPOE PASSWORD

1. MODIFY UPSTREAM QOS INTERFACE

2. MODIFY DOWNSTREAM QOS INTERFACE




4. CREATE BRIDGE PORT UNTAGGED VLAN


Sta

nd

ard

Op

era

tin

g P

roce

du

re

Figure 25 Delete internet service flow (Bridge)

Figure 26 Create IPTV service flow

Figure 27 Delete IPTV service flow





5. CREATE IGMP CHANNEL



3. DELETE DOWNSTREM QOS INTERFACE







Sta

nd

ard

Op

era

tin

g P

roce

du

re

Figure 28 Create voice service flow

Figure 29 Modify POTS port flow

Figure 30 Delete voice service flow




4. CREATE IPHOST

5. CREATE VOICE ONT VOIP-CONFIG

6. CREATE VOICE ONT SIP-CONFIG

7. CREATE VOICE ONT VOICE-SIP-PORT

8. CREATE VOICE ONT VOICE-PORT & UNLOCK

1. LOCK VOICE ONT POTS

2. MODIFY VOICE ONT VOICE-SIP-PORT

3. UNLOCK VOICE ONT POTS

1. LOCK VOICE ONT POTS

2. MODIFY VOICE ONT VOICE-SIP-PORT

3. MODIFY VOICE-ONT VOICE-PORT





Sta

nd

ard

Op

era

tin

g P

roce

du

re

Figure 31 Create E1 service flow

1. CREATE IACM VLAN

2. CREATE SERVICE CUSTOMER

3. CREATE SERVICE VPLS

4. UNLOCK INTERFACE PORT ETHERNET-LINE

5. SET ETHERNET-LINE MAU TYPE AND UNLOCK

6. CREATE SFPE1T1 CLOCK

7. CREATE SFPE1T1 PWTDM

8. CREATE SFPE1T1 FRAMER

9. CREATE SFPE1T1 LIU

10. CREATE BRIDGE PORT ON SFP E1 IN NELT-B CARD

11. UNLOCK INTERFACE PORT ON ONT




15. CREATE CES ONT PROFILE

16. CREATE CES ONT LINE

11. CREATE CES ONT SERVICE


Sta

nd

ard

Op

era

tin

g P

roce

du

re

Figure 32 Delete E1 service flow


2. DELETE EQUIPMENT SFPE1T1 PWTDM

3. DELETE EQUIPMENT SFPE1T1 CLOCK

4. REMOVE ETHERNET LINE MAU TYPE AND LOCK

5. DELETE CES ONT SERVICE

6. DELETE CES ONT LINE

7. DELETE CES ONT PROFILE

8. DELETE ONT BRIDGE PORT

9. LOCK ONT INTERFACE PORT



12. DELETE IACM VLAN

13. DELETE SERVICE VPLS

14. DELETE SERVICE CUSTOMER


Sta

nd

ard

Op

era

tin

g P

roce

du

re

Figure 33 Create point to point tagged vlan flow

Figure 34 Delete point to point tagged vlan flow

1. CREATE IACM VLAN

2. CREATE SERVICE CUSTOMER

3. CREATE SERVICE VPLS

4. UNLOCK INTERFACE PORT ETHERNET-LINE

5. SET ETHERNET-LINE MAU TYPE AND UNLOCK

6. CREATE BRIDGE PORT TAGGED VLAN


2. REMOVE ETHERNET-LINE MAU TYPE AND LOCK

3. LOCK INTERFACE PORT ETHERNET-LINE

4. DELETE SERVICE VPLS

5. DELETE SERVICE CUSTOMER

6. DELETE IACM VLAN

SOP XGPON ALU Provisioning v1 13112014(1)

Documents

Transcript of SOP XGPON ALU Provisioning v1 13112014(1)