How to Install a Return Air Duct in Basement?

3
1/3 How to Install a Return Air Duct in Basement? thetechbizz.com/how-to-install-a-return-air-duct-in-basement When it comes to air ducts, most people don’t know this. Other than the standard air ducts, there are return ducts installed throughout your home that keep air circulating. Therefore, According to Commercial air duct and dryer vent cleaning Roswell GA services, there are hot and cold spots around your home that need some air balance to keep the atmosphere the same all around. For this, return air duct in basement are helpful and installed along with ductwork. The function of Return Duct As you know, air ducts transfer cool or warm air around your home, building a comfortable environment. Thus, That’s how your HVAC system works. However, that’s not all. Moreover, Other than the ductwork, there are return ducts installed. Its primary function is carrying the air back to the furnace or the air handler. It circulates the air back out through supply vents. Today, most modern systems are usually designed to have one or two returns for the whole system. Although it may be less considering the size of the house, they’re effective. But, this doesn’t mean old houses already have return ducts installed. Therefore, In most cases, you have to do it yourself. Before that, don’t forget to clean and perform air duct sanitizing in Roswell GA carefully to remove all contaminants from air ducts. Problems Caused if There Are No Return Air Ducts

description

When it comes to air ducts, most people don’t know this. Other than the standard air ducts, there are return ducts installed throughout your home that keep air circulating.

Transcript of How to Install a Return Air Duct in Basement?

Page 1: How to Install a Return Air Duct in Basement?

1/3

How to Install a Return Air Duct in Basement?thetechbizz.com/how-to-install-a-return-air-duct-in-basement

When it comes to air ducts, most people don’t know this. Other than the standard air

ducts, there are return ducts installed throughout your home that keep air circulating.

Therefore, According to Commercial air duct and dryer vent cleaning Roswell GA services,

there are hot and cold spots around your home that need some air balance to keep the

atmosphere the same all around. For this, return air duct in basement are helpful and

installed along with ductwork.

The function of Return Duct

As you know, air ducts transfer cool or warm air around your home, building a

comfortable environment. Thus, That’s how your HVAC system works. However, that’s

not all. Moreover, Other than the ductwork, there are return ducts installed. Its primary

function is carrying the air back to the furnace or the air handler. It circulates the air back

out through supply vents.

Today, most modern systems are usually designed to have one or two returns for the

whole system. Although it may be less considering the size of the house, they’re effective.

But, this doesn’t mean old houses already have return ducts installed. Therefore, In most

cases, you have to do it yourself. Before that, don’t forget to clean and perform air duct

sanitizing in Roswell GA carefully to remove all contaminants from air ducts.

Problems Caused if There Are No Return Air Ducts

Page 2: How to Install a Return Air Duct in Basement?

2/3

Here you might have guessed, and if the return ducts aren’t installed, air circulation is

affected, resulting in several problems.

Poor airflow affects your overall ductwork and HVAC system.

Hot and cold spots around the house.

Weird odors around your home.

Air quality problems in all rooms.

Noisy HVAC system.

Best Places to Install Return Ducts

Understandable, the purpose of return ducts is to send the air back into the HVAC system.

Your instinct might say to install a return duct with a regular air vent. Although it’s a great

idea, it could be a poor choice. According to commercial air duct and dryer vent cleaning

Roswell GA services, return ducts should be installed anywhere except between the

kitchen and bathrooms. Now you don’t want to circulate the hot moist, or contaminated

air around the house. That will only result in a disaster and bad smells.

However, the story in two-floor homes is different. The general rule there is installing

return ducts as close to the thermostat as possible. Since the thermostat is installed at a

centralized location, monitoring and recording temperature reading of every room is easy.

Anyway, most homeowners have return air duct in basement, which is the most effective

place if taken care of properly.

6 Step Installation of Return Air Duct in Basement

Most DIYers have tried installing air ducts, but the return duct’s installation is not that

difficult. Here are six easy steps :

1: Finding Where Ducts G

Most homeowners make this simple mistake of not planning the whole idea. It’s better to

start with the location you want to start return ducts from and trace down where the duct

will go.

According to air duct sanitizing Roswell GA, you might want to cut a hole low in the

drywall. It is the place you want your return air grille to go. On the other hand, while

trying to cut the new return registers into an existing house, make sure not to cut any

pipes or electric wires in the wall.

Next, start making holes appropriate to the size of the grille. Keep making holes until your

desired number of holes is ready. There should be at least one hole in every room except

the bathroom.

2: Panning for Adding

Page 3: How to Install a Return Air Duct in Basement?

3/3

After step one, go back to the basement after some refreshments and locate all the holes.

Start from the furthest hole to install return air, panning backward to where the furnace

is. Carefully nail the panning to the ceiling joists. Next, from the furthest hole, nick the

pan to bend up and fit in place, closing off any space left.

Halts are all panning in the joist at the same point, there are hot and cold spots around

your home that need some air balance to keep the atmosphere the same all around. For

this, return air duct in a basement are helpful and installed along with ductwork near the

furnace. Nick this side too and take it up to the floor. Next, cut the holes in the pan to get

the return air throughout the house back to the furnace. The holes should line

perpendicular to the joists for a clean set-up.

3: Enclose the New Return Ductwork

Services like commercial air duct and dryer vent cleaning Roswell GA tell us to enclose

return ductwork carefully. While installing the return air duct, run it, so it covers up all

the holes you cut. After that, at the top of the return air ducts, cut holes that match the

holes in the panning. It allows air to go into return ducts.

Make a tight seal that connects the return air duct using s-slips and drive cleats to the

bottom of the ceiling joists. It’s a good idea to insulate the return air duct with one and a

half-inch foil-faced duct wrap, preventing heat gain or loss or air circulation. Don’t forget

to use a one inch galvanized hanger stamp to secure the ducts to the ceiling.

4: New Air Return Duct to Furnace

At the end of the return duct next to where the furnace is, cut a hole. That’s the place

where another duct, attached, goes down into the furnace. Next, carefully cut a hole inside

the furnace, which matches the size of the filter rack.

5: New Air Filter for Filter Rack.

With a silicone caulk, seal all joints after installing your HVAC filter to your rack. Next,

see if you need air duct sanitizing Roswell GA for cleaning your new ductwork.

6: Adding Return Air Register Covers

With screws, make sure all your return air registers are secured carefully. Viola, installing

your air duct system for return ductwork is ready.

However, As mentioned, Return ducts are the best if installed in places like the basement

or attic.

Since they take someplace, they’re added around the house or as needed. Their primary

function is to act as an airbus that sends air back to the HVAC system, improving the

indoor atmosphere.